WLT_TFT8060使用说明

MKH 8060 Instruction manualImportant safety instructions Important safety instructions1.Read these safety instructions and the instruction manual of the product.2.Keep these safety instructions and the instruction manual of the product.Always include all instructions when passing the product on to third parties.3.Only use attachments, accessories and spare parts specified by the manu-facturer.4.Caution: The protective basket and pop shield must be completely dry whenyou mount them on the microphone. Moisture can cause malfunctions or damage to the capsule.5.Connect the microphone only to microphone inputs and supply units thatprovide 48 V phantom powering in accordance with IEC 61938.6.Do not attempt to open the product housing on your own.7.Refer all servicing to qualified service personnel. Servicing is requiredwhen the product has been damaged in any way, liquid has been spilled or objects have fallen into the product, when the product has been exposed to rain or moisture, does not operate normally, or has been dropped.e the product only under the conditions of use listed in the specifications.9.Let the product come to ambient temperature before switching it on.10.Do not operate the product if it was damaged during transportation.11.Always run cables so that no one can trip over them.12.Keep the product and its connections away from liquids and electricallyconductive objects that are not necessary for operating the product.13.Do not use any solvents or aggressive cleaning agents to clean the product.14.Caution: Very high signal levels can damage your hearing and your loud-speakers. Reduce the volume on the connected audio devices beforeswitching on the product; this will also help prevent acoustic feedback. Intended useThe product is designed for indoor use.It is considered improper use when the product is used for any application not named in the corresponding instruction manual.Sennheiser does not accept liability for damage arising from improper use or misuse of this product and its attachments/accessories.Before putting the products into operation, please observe the respective country-specific regulations!MKH 8060MKH 8060Delivery includesDelivery includes•Microphone, consisting of the MKH 8060 microphone head and the MZX 8000 XLR module •MZQ 8060 microphone clamp •MZW 8060 foam windshield •Instruction manual •Frequency response sheet •Threaded transport tubeProduct overview11 Foam windshield2 Microphone head3 XLR module4 Microphone clamp (thread adaptor included for 3/8" and 5/8" threads)Putting the MKH 8060 into operation Putting the MKH 8060 into operation Connecting the microphoneConnection data of the MKH 8060:•48 V ±4 V phantom powering (P48, as per IEC 61938)•XLR-3 connector, balancedTo connect the MKH 8060 to a mixing console or recording device:f Connect the socket of the microphone cable to the microphone.f Connect the connector of the microphone cable to the mixing console orrecording device.Attaching the microphonef Select the suitable mounting thread:•Without thread insert: 5/8" thread•Thread insert: 3/8" threadf Screw the microphone clamp 4 to a stand.f Place the microphone with its back end into the microphone clamp: Makesure that the lateral slots are not covered.f Orient the microphone together with the microphone clamp and fix them byscrewing the wing screw tight.MKH 8060Using optional modulesTo suppress structure-borne noise, you can use one of the optional shockmounts.Sennheiser MZS 20-1 Sennheiser MZS 40Using the windshieldThe windshield changes the sound only slightly, but attenuates wind noise by approx. 25 dB.f Place the MZW 8060 foam windshield 1 over the microphone head 2 so thatall lateral slots are covered.Alternative windshields are available as accessories and can be found on the MKH 8060 product page at .Using optional modulesYou can retrofit and extend the microphones of the modular MKH 8000 micro-phone series by using optional modules.The MZF 8000 II filter moduleThe MZF 8000 II filter module has been specially designed for broadcast and film applications. It effectively filters out interference caused by infrasound, such a lowfrequency wind and handling noise.f If necessary, disconnect a connected XLR cable in order to not distort theMKH 8060Transporting the microphone cable and to avoid short-circuits.f Unscrew the microphone head 2 from the XLR module 3.f Screw the MZF 8000 II filter module 4 at a suitable place in the audio signalTransporting the microphonef Let the microphone dry if you used it under extreme climatic conditions.f If necessary, remove the windshield or take the microphone out of the basketwindshield.f Slide the microphone into the transport tube.MKH 8060Cleaning and maintaining the microphoneCleaning and maintaining the microphoneNOTICEDAMAGE TO THE PRODUCT DUE TO LIQUIDS!Liquids entering the product can short-circuit the electronics or damage the mechanics. Solvents or cleansing agents can damage the surface of the prod-uct.f Keep all liquids away from the product.f Only use a soft, slightly damp cloth to clean the product. SpecificationsPick-up pattern super-cardioid/lobarFrequency response50 Hz to 25,000 HzSensitivity-24 dBV/Pa (63 mV/Pa)Max. sound pressure level129 dB SPLEquivalent noise level A-weightedCCIR-weighted 11 dB(A) 23 dBNominal impedance25 ΩMin. terminating impedance 2 kΩPhantom powering48 V ± 4 V (P48, IEC 61938) Current consumption 3.3 mADiameter19 mmLengthwith MZX 8000 XLR module 145 mm 178 mWeightwith MZX 8000 XLR module 80 g 112 gOperating temperature-10 °C to +60 °CMKH 8060MKH 8060SpecificationsPolar pattern30°150°120°60°90°0510152025dB30°0°180°150°120°60°90°125 Hz 250 Hz 500 Hz 1,000 Hz2,000 Hz 4,000 Hz 8,000 Hz 16,000 HzFrequency response-10-20-30-40-50-60dB 90°0°50 H z100 H z200 H z500 H z1 k H z2 k H z5 k H z10 k H z20 k H zManufacturer declarationsManufacturer declarationsWarrantySennheiser electronic GmbH & Co. KG gives a warranty of 24 months on these products.For the current warranty conditions, please visit our website at or contact your Sennheiser partner.Warranty FOR AUSTRALIA and NEW ZEALAND ONLY:Sennheiser Australia Pty Ltd provides a warranty of 24 months on these products. For the current warranty conditions, visit Sennheiser website:Australia: https:///New Zealand: https:///Sennheiser goods come with guarantees that cannot be excluded under Aus-tralian and New Zealand Consumer law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably fore-seeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.This warranty is in addition to other rights or remedies under law. Nothing in this warranty excludes, limits or modifies any remedy available to be consumer which is granted by law.To make a claim under this contract, raise a case via Sennheiser website Australia: https:///service-support-contactNew Zealand: https:///service-support-contactAll expenses of claiming the warranty will be borne by the person making the claim.Sennheiser international warranty is provided by: Sennheiser Australia Pty Ltd (ABN 68 165 388 312) Level 14, Tower A Zenith Building, 821 Pacific Highway, Chatswood NSW 2067, AustraliaMKH 8060Manufacturer declarations In compliance with the following requirementsEU: UK:• WEEE Directive (2012/19/EU)•WEEE Regulations (2013)Notes on disposalThe symbol of the crossed-out dumpster on the product, the (rechargeable) battery (if applicable) and/or the packaging indicates that these products must not be disposed of with normal household waste, but must be disposed of sep-arately at the end of their service life. For the packaging, follow the regulations in your country for separating waste. Improper disposal of packaging materials can be harmful to your health and the environment.The separate collection of waste electrical and electronic equipment, (re-chargeable) batteries (if applicable) and packaging is intended to promote reuse and recycling and to prevent negative impacts on public health and the environment, for example due to hazardous substances contained in these products. At the end of their service life, recycle electrical and electronic equipment and (rechargeable) batteries so that their materials can be reused and to prevent environmental pollution.If (rechargeable) batteries can be removed without destroying them, you are obliged to dispose of them separately (see the product’s operating instructions for information on how to remove the batteries safely). Be especially careful when handling (rechargeable) batteries containing lithium, as these pose spe-cial hazards, such as the risk of fire and/or health risks if button cells are swal-lowed. Reduce battery waste as much as possible by using longer-life batteries or rechargeable batteries.Further information on the recycling of these products can be obtained from your municipal administration, from the municipal collection points, or from your Sennheiser partner. You may also be able to return electrical or electronic equipment to your distributor, if they are legally required to do so. By dispos-ing of your batteries properly, you are helping to protect public health and the environment.MKH 8060Manufacturer declarationsUK Declaration of conformity•RoHS Regulations (2012)•EMC Regulations (2016)Importer: Sennheiser UK Ltd.Pacific House, Third Avenue, Globe Park, MarlowBuckinghamshire SL7 1EY, United KingdomEU Declaration of conformity•RoHS Directive (2011/65/EU)•EMC Directive (2014/30/EU)The full text of the EU declaration of conformity is available at the following internet address: /download.Statements regarding the FCC and Industry Ca-nada rulesThis device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interfer-ence that may cause undesired operation.Contact information:Sennheiser Electronic Corporation1 Enterprise Drive, Old Lyme, CT 06371MKH 8060Compliance ComplianceEuropeUKUSA FCC 47 CFR 15 subpart BCanada Industry Canada CAN ICES-003(B) /Australia/New ZealandVietnam Kể từ ngày 1 tháng 12 năm 2012, các sảnphẩm được sản xuất bởi Sennheiser tuânthủ Thông tư 30/2011/TT-BCT quy định vềgiới hạn cho phép đối với một số chất độchại trong các sản phẩm điện và điện tử.MKH 8060Sennheiser electronic GmbH & Co. KGAm Labor 1, 30900 Wedemark, Germany, Printed in Germany, Publ. 07/23, 581394/A04。

VSX-6155-V2DM&P Vortex86SX 300MHzPC/104 CPU Modulewith 4S/2USB/VGA/LCD/AUDIO/LAN/GPIO 128MB DDR2 OnboardUser’s Manual(Revision 1.0A)CopyrightThe information in this manual is subject to change without notice for continuous improvement in the product. All rights are reserved. The manufacturer assumes no responsibility for any inaccuracies that may be contained in this document. And makes no commitment to update or to keep current the information contained in this manual.No part of this manual may be reproduced, copied, translated or transmitted, in whole or in part, in any form or by any means without the prior written permission of the ICOP Technology Inc..©Copyright 2007 ICOP Technology Inc.Manual No. IUM6155-V2000-01 Ver.1.0A July, 2010Trademarks AcknowledgmentVortex86SX™ is the registered trademark of ICOP Technology Inc.Other brand names or product names appearing in this document are the properties and registered trademarks of their respective owners. All names mentioned herewith are served for identification purpose only.T a b l e o f C o n t e n t sT a b l e o f C o n t e n t s (iii)C h a p t e r 1 Introduction (1)1.1 Packing List (1)1.2 Product Description (2)1.3 Specifications (3)1.4 Board Dimension (5)C h a p t e r 2 Installation (6)2.1 Board Outline (6)2.2 Connectors & Jumpers Location (7)2.3 Connectors & Jumpers Summary (9)2.4 Pin Assignments & Jumper Settings (11)2.5 System Mapping (23)2.6 Watchdog Timer (26)2.7 GPIO (27)2.8 SPI flash (28)C h a p t e r 3 Driver Installation (29)Appendix (30)A. TFT Flat Panel Data Output (30)B. TFT Flat Panel Support List (31)C. LVDS Flat Panel Support List (33)D. Flat Panel Hardware Setting (34)E. Flat Panel Wiring and Lighting (35)F. TCP/IP library for DOS real mode (36)G. BIOS Default Setting (37)Warranty (38)C h a p t e r 1 Introduction1.1 Packing ListProduct NamePackageVSX-6155-V2Embedded Vortex86SX CPU All-in-One Board Manual & Drivers CD x 1 RS232 cable x 4PRINT cable x1 IDE cable x 1USB cable x 1 (USB port x 2) VGA cable x 1 LAN cable x 1 GPIO cable x 1 AUDIO Line x2 PS/2 Mouse cable x 1 PS/2 Keyboard cable x 1 Screw Kit x 11.2 Product DescriptionThe VSX-6155-V2 family of low-power x86 embedded controller is designed to meet PC/104 specification, and integrated with the following features.300 MHz Vortex86SX System-On-ChipVGA, TFT LCD support up to1280x1024 resolution128 / 256MB DDR2 system memory Enhanced IDE10/100Mbps Ethernet2 USB 2.0 (host)Up to 4 serial portsParallel port16-bit GPIOs Onboard 2MB SPI Flash PC/104-Plus expansion busMeet PC/104 stacking spec.2 watchdog timerJTAG interfaceAMI BIOSSingle voltage +5V DCSupport extended operatingtemperature range of -20°C to +70°CThe VSX-6155-V2 PC/104 family of embedded controller is designed with backward compatibility in mind, to provide migration path for projects facing end-of-life challenges with their existing x86 based PC/104 controller. The VSX-6155-V2 family of controller is designed as a plug in replacement, with backward compatibility to support legacy software to help extend existing product life cycle without heavy re-engineering.VSX-6155-V2 is suitable for broad range of data-acquisition, Industrial automation, Process control, Automotive controller, AVL, Intelligent Vehicle management devic,Medical device, Human machine interface, Robotics, machinery control And more…application that required small footprint, low-power and low-cost hardware with open industry standard such as PC/104.1.3 SpecificationsFeatures VSX-6155-V2 CPU DM&P SoC CPU Vortex86SX- 300MHzReal Time Clock with Lithium Battery Backup Cache L1:16K I-Cache, 16K D-CacheBIOS AMI BIOSBus Interface PC/104 Standard Compliant (Optional: PCI-104)System Memory 128 / 256MB DDR2 OnboardWatchdog Timer Software programmable from 30.5 us to 512 seconds x2sets(Watchdog 1 fully compatible with M6117D) VGA XGI Volari Z9s ChipsetVGA and TFT Flat Panel Interface SupportLVDS Flat Panel Interface Support (Optional)Onboard 32MB VGA MemorySupport resolution up to 1280 x 1024,16MB colors LAN Integrated 10/100M EthernetAUDIO CM119 USB Audio controllerI /O Interface Enhanced IDE port x1RS-232 port x3RS-232/422/485 port x1 (RS485: Auto Direction)Parallel port x1USB port x2 (USB 2.0 version)16-bit GPIO port x110/100Mbps Ethernet port x1Connectors 2.00 mm ∅ 44-pin box header for IDE x12.00 mm ∅ 44-pin box header for LCD x 12.00 mm ∅ 10-pin box header for VGA x12.00 mm ∅ 10-pin box header for USB x12.00 mm ∅ 26-pin box header for Print x12.00 mm ∅ 20-pin box header for 16-bit GPIO x12.00 mm ∅ 10-pin box header for RS-232 x42.00 mm ∅ 8-pin header for Ethernet x 12.54 mm ∅ 5-pin box header for Keyboard x12.54 mm ∅ 5-pin header for Mouse x12.54 mm ∅ 4-pin header for DC-in x12.54 mm ∅ 3-pin header for RS-485 x12.54 mm ∅ 2-pin header for Reset x12.54 mm ∅ 7-pin header for Redundancy x1(Opt)2.54 mm ∅ 2-pin header for SYS-Fail-SW- x1(Opt)1.25 mm ∅ 6-pin Wafer for JTAG x11.25 mm ∅ 4-pin Wafer for Line-out/MIC-in x2Flash Disk Support Onboard 2MB SPI Flash Disk (Driver: A)44-pin IDE Flash Disk( EmbedDisk 16MB or above)Power Requirement Single Voltage +5V@ 620mADimension 90 X 96mm (3.54 x 3.77 inches)Weight 90gOperating Temperature -20o C ~ +70o C-40°C ~ +85°C (Optional)1.4 Board DimensionC h a p t e r 2Installation2.1 Board Outline(Note1: COM2 RS232/422/485 is selected by BIOS setting) (Note2: PCI-104 connector is optional)(Note3: VI/O Default setting of PCI-104 connector is +5V) (Note4: Redundancy Signal and System-Fail-SW are optional)2.2 Connectors & Jumpers Location ConnectorsJumpers & LEDs2.3 Connectors & Jumpers SummarySummary TableIDE-IDE Active LED (Green ) LED-SMD LEDMTBF-MTBF-Out (Orange) LED-SMDLEDLED 3 LAN Link/Active LED (Green) LED-SMD LED 4 LAN Duplex LED ( Yellow ) LED-SMD SP1 BUZZER2.4 Pin Assignments & Jumper SettingsJ1: IDE (44 Pins)J2: USB Pin # Signal Name Pin # Signal Name1 VCC2 VCC3 LUSBD3-4 LUSBD2-5 LUSBD3+6 LUSBD2+7 GND8 GND9 GGND 10 GGND Pin # Signal Name Pin # Signal Name1 IDERST2 GND3 IDED74 IDED85 IDED6 6 IDED97 IDED58 IDED109 IDED4 10 IDED11 11 IDED3 12 IDED12 13 IDED2 14 IDED13 15 IDED1 16 IDED14 17 IDED0 18 IDED15 19 GND 20 NC 21 IDEREQ 22 GND 23 IDEIOW 24 GND 25 IDEIOR 26 GND 27 ICHRDY 28 GND 29 IDEACK 30 GND 31 IDEINT 32 NC 33 IDESA1 34 IDECBLID 35 IDESA0 36 IDESA2 37 IDECS-0 38 IDECS1 39 IDELED 40 GND 41 VCC 42 VCC 43 GND 44 NCJ4: LANPin # Signal Name Pin # Signal Name1 ATX+2 ATX-3 ARX+4 LED05 LED0+6 ARX-7 LED1+ 8 LED1J5: JTAGPin # Signal Name Pin # Signal Name1 VCC2 GND3 TCK4 TDO5 TDI6 TMSJ6: RESETPin # Signal Name Pin # Signal Name1 RST_SW2 GNDJ7: Redundancy (Optional)Pin # Signal Name Pin # Signal NameSYS-FAIL-OUT1 GND 23 SYS-FAIL-IN4 GPCS05 SYS-GPCS-IN6 TXD9\7 RXD9\J8: System-Fail-Switch (Optional)Pin # Signal Name1 SYS-SW-IN2 GNDJ9: PS/2 KeyboardPin # Signal Name Pin # Signal Name1 KBCLK2 KBDAT3 NC4 GND5 VCCJ10: PS/2 MousePin # Signal Name Pin # Signal Name1 MSCLK2 MSDATA3 NC4 GND5 VCCJ11: COM 1 (Optional TTL/ GPIO-P4)Pin # SignalNamePin #SignalName1 DCD12 RXD13 TXD14 DTR15 GND6 DSR17 RTS1 8 CTS19 RI1 10 NCJ12: COM2 RS232 / 422 / 485 (Optional: TTL)Pin # Signal Name Pin # Signal Name1 DCD2/ 422TX- / RS485-2 RXD2 / 422TX+ / RS485+3 TXD2/422RX+ 4 DTR2/422RX-5 GND6 DSR27 RTS28 CTS29 RI2 10 NCJ13: GPIO (Port 0 / 1)Pin # Signal Name Pin # Signal Name1 GND2 VCC3 GP004 GP105 GP016 GP117 GP02 8 GP129 GP03 10 GP1311 GP04 12 GP1413 GP05 14 GP1515 GP06 16 GP1617 GP07 18 GP1719 VCC 20 GNDJ15: RS485 (Auto direction)Pin # Signal Name1 RS485＋2 RS485－3 GNDJ16: Power Connector (Terminal Block 5.0mm) Pin # Signal Name1 +5V2 GNDJ17: COM3 (Optional: TTL)Pin # Signal Name Pin # Signal Name1 DCD32 RXD33 TXD34 DTR35 GND6 DSR37 RTS3 8 CTS39 RI3 10 NCJ18: PRINTPin # Signal Name Pin # Signal Name1 STB- 14 AFD-2 PD0 15 ERR-3 PD1 16 INIT-SLIN-4 PD2 175 PD3 18 GND6 PD4 19 GND7 PD5 20 GND8 PD6 21 GND9 PD7 22 GND10 ACK- 23 GND11 BUSY 24 GND12 PE 25 GND13 SLCT 26 NCJ19: COM4 (Optional: TTL)Pin # Signal Name Pin # Signal Name1 DCD42 RXD43 TXD4 4 DTR45 GND6 DSR47 RTS4 8 CTS49 RI4 10 NCJ20: PC104 Connector – 64pinPin # Signal Name Pin # Signal Name* 2 GND1 IOCHCHKRESETDRV3 SD7 45 SD6 6 VCC7 SD5 8 IRQ99 SD4 10 -5V 11 SD3 12 DRQ2 13 SD2 14 -12V 15 SD1 16 OWS 17 SD0 18 +12V 19 IOCHRDY 20 GNDSMEMW*21 AEN 22*SMEMR 23 SA19 24* 25 SA18 26 IOW* 27 SA17 28 IOR* 29 SA16 30 DACK3 31 SA15 32 DRQ3* 33 SA14 34 DACK1 35 SA13 36 DRQ1*REFRESH 37 SA12 3839 SA11 40 SYSCLK 41 SA10 42 IRQ7 43 SA9 44 IRQ6 45 SA8 46 IRQ5 47 SA7 48 IRQ4 49 SA6 50 IRQ3DACK2* 51 SA5 5253 SA4 54 TC 55 SA3 56 BALE 57 SA2 58 VCC 59 SA1 60 OSC 61 SA0 62 GND 63 GND 64 GNDJ21: PC104 Connector – 40pinJ22: 4P Power Source (Interconnect to PC/104 – J20) Pin # Signal Name1 -5V2 -12V3 +12V4 GNDPin # Signal Name Pin # Signal Name1 GND2 GND3 MEMCS16 *4 SBHE *5 IOCS16 * 6 SA237 IRQ10 8 SA229 IRQ11 10 SA2111 IRQ12 12 SA2013 IRQ15 14 SA1915 IRQ14 16 SA1817 DACK0 * 18 SA1719 DRQ0 20 MEMR *21 DACK5 * 22 MEMW *23 DRQ5 24 SD825 DACK6 * 26 SD927 DRQ6 28 SD1029 DACK7 * 30 SD1131 DRQ7 32 SD1233 VCC 34 SD1335 MASTER * 36 SD1437 GND 38 SD1539 GND 40 NCJ23: PC/104 + (Optional)VI/O Default setting: +5VIf you need to use VI/O as +3.3V, please see the page 19. Pin # A B C D1 GND NC +5V AD002 VI/O(+5V) AD02 AD01 +5V3 AD05 GND AD04 AD034 C/BE0# AD07 GND AD065 GND AD09 AD08 GND6 AD11VI/O(+5V) AD10 GND7 AD14 AD13 GND AD128 +3.3V C/BE1# AD15 +3.3V9 SERR# GND NC PAR10 GND PERR# +3.3V NC11 STOP# +3.3V LOCK# GND12 +3.3V TRDY# GND DEVSEL#13 FRAME# GND IRDY# +3.3V14 GND AD16 +3.3V C/BE2#15 AD18 +3.3V AD17 GND16 AD21 AD20 GND AD1917 +3.3V AD23 AD22 +3.3V18 IDSEL0 GND IDSEL1 IDSEL2VI/O(+5V) IDSEL319 AD24 C/BE3#20 GND AD26 AD25 GND21 AD29 +5V AD28 AD2722 +5V AD30 GND AD3123 REQ0# GND REQ1# VI/O(+5V)24 GND REQ2# +5V GNT0#25 GNT1# VI/O(+5V) GNT2# GND26 +5V CLK0 GND CLK127 CLK2 +5V CLK3 GND28 GND INTD# +5V RST#29 +12V INTA# INTB# INTC#30 -12V NC NC GNDPlease remove the 0 ohm (1206 type) of R212 and add 0 ohm (1206 type) on R213J24: VGAPin # SignalNamePin #SignalName1 ROUT 2 GND3 GOUT 4 GND5 BOUT 6 GND7 HSYNC 8 GND9 VSYNCD 10 GNDJ25: LCD (DVO) ConnectorPin # Signal Name Pin # Signal Name1 +3.3V2 +3.3V3 LG24 LG35 LG46 LG57 NC 8 NC9 LR0 10 LR111 LR2 12 LR313 LR4 14 LR515 GND 16 NC17 NC 18 NC19 NC 20 GND21 NC 22 NC23 LB0 24 LB125 LB2 26 LB327 LB4 28 LB529 NC 30 NC31 LG0 32 LG133 GND 34 GND35 NC 36LCLK37 NC 38 LDE39 NC 40LHSYNC41 NC 42LVSYNC43 LBACKL 44 LVDDEN(Please refer to Appendix A, for TFT Flat Panel Data Output)J26~J31: Display type setup (CRT /LCD) Connector Pin # Signal Name1 VCCJ262 GPIOA3 GND1 VCCJ272 GPIOB3 GND1 VCCJ282 GPIOC3 GND1 VCCJ292 GPIOD3 GND1 VCCJ302 GPIOE3 GND1 VCCJ312 GPIOF3 GND(Please refer to Appendix D, for Display type setup)J33: LINE OUTPin # Signal Name1 LOUTR2 GND3 GND4 LOUTLJ34: MIC-INPin # Signal Name1 MICVREF2 GND3 GND4 MIC-IN2.5 System Mapping2.6 Watchdog TimerThere are two watchdog timers in Vortex86SX/DX CPU. One is compatible with M6117D watchdog timer and the other is new. The M6117D compatible watchdog timer is called WDT0 and new one is called WDT1.We also provide DOS, Linux and WinCE example for your reference. For more technical support, please visit: /tech or download the PDF file:/tech/vortex86dx/2.7 GPIO (General Purpose Input / Output)40 GPIO pins are provided by the Vortex86SX/DX for general usage in the system. All GPIO pins are independent and can be configured as inputs or outputs, with or without pull-up/pull-down resistors.We also offer DOS, Linux and WinCE example for your reference. For more technical support, please visit: /tech or download the PDF file:/tech/vortex86dx/2.8 SPI flash (Serial Peripheral Interface)As SPI Flash (Serial Peripheral Interface) offers many benefits including: reduced controller pin count, smaller and simpler PCBs, reduced switching noise, less power consumption, and lower system costMany of users may consider using a formatted SPI flash to boot for the system or emulate SPI flash as Floppy (A: Driver or B: Driver). Then you must know how to set for this condition in CMOS Setup and boot up under DOS 6.22, X-DOS, DR-DOS and Free DOS.For more technical support, please visit: /tech or download the PDF file: /tech/vortex86dx/C h a p t e r 3Driver InstallationVGAThe Vortex86DX processor also use external Display chip ““Volari™ Z9s” which is an ultra low powered graphics chipset with total power consumption at around 1-1.5 W. It is capable in providing VGA display output upto 1600x1200. With DVO interface, developers could easily connect flat Panel to support TFT and LVDS output.LANThe Vortex86DX processor also integrated 10/100Mbps Ethernet controller that supports both 10/100BASE-T and allows direct connection to your 10/100Mbps Ethernet based Local Area Network for full interaction with local servers, wide area networks such as the Internet.The controller supports: Half / Full-Duplex Ethernet function to double channel bandwidth, auto media detection.AUDIOCM119 is a highly integrated single chip USB audio controller specifically for VoIP (Voice over internet protocol) application. All essential analog modules are embedded in CM119, including dual DAC and earphone driver, ADC, microphone booster, PLL, regulator, and USB transceiver.8 GPIO pins can constitute a 24 key matrix directly support keypad control function without MCU.Many features are programmable with jumper pins or external EEPROM. Vender can customize unique USB VID/PID to EEPROM for VoIP software authentication. Moreover, individual unique phone number for each device is possible via serial number stored in external EEPROM.Operating system supportThe Vortex86SX-6155-V2 PC/104 CPU board supports Embedded software: Free DOS, DOS 6.22, PCDOS 7.1, DR-DOS, x-DOS, OS/2, Windows CE 5.0 / 6.0Please get the drivers from the Driver CD which attached with the standard packing ofVortex86SX-6155-V2 board or please get it from DMP official website:/tech/vortex86sx/Vortex86SX-6155-V2 also supports most of the popular Linux distributions, for more detail information, please visit DMP official website: /tech/vortex86sx/Appendix A. TFT Flat Panel Data OutputB. TFT Flat Panel Support ListSize Brand Resolution Model No.image 320x240 FG050701DSSWBG015.7” Data5.7” Optrex 320x240 55264GD057J-FW-ABN5.7” TOSHIBA 320x240 LTA057A343F5.7” Sharp 320x240 (QVGA / VGA) LQ057Q3DC02(QVGA / VGA) TCG057QV1AC-G105.7” Kyocera 320x240(QVGA / VGA) PD057VU4 /U55.7” PVI 320x240image 640x480 FG050710DSSWJG01/DG015.7” Data5.7” Ampire 640x480 AM-640480GTMQW-T00H5.7” URT 640x480 UMSH-8004MD-T5.7” Sharp 640x480 LQ057V3DG015.7” CPT 640x480 CLAA057VA016.4” PVI 640x480 V16C6448AC6.4” LG-PHILIPS 640x480 LB064V02/VT5/VT46.4” PVI 640x480 PD064VT26.4” Sharp 640x480 LQ064V3DG017” AUO 800x480 C070VW02V0image 800x480 FG0700A0DSSWBG01 7” Data7” LG-PHILIPS 800x480 (TFT 24 bits) LB070WV17” HITACHI 800x480 TX18D57VM2BAA 7” Samsung 800x480 LMS700KF057” PVI 800x480 PM070WL4 7” URT 800x480 UMSH-8173MD-1T HSIN 800x480 LW700AT9309 7” CHI8” Sharp 640x480 LQ080V3DG01Size Brand Resolution Model No.V024bits) A080SN01(TFT8” AUO 800x6008.4” Sharp 800x600 LQ084S3DG01 10.4” PVI 640x480 PD104VT1/VT2 10.4” NEC 640x480 NL6448AC33-18 10.4” NEC 640x480 NL6448AC33-29 10.4” NEC 640x480 NL6448BC33-59 10.4” Sharp 640x480 LQ104V1DG51/DG61 10.4” Sharp 640x480 LQ10d368 11” Sharp 800x480 LQ110Y3DG01 12.1” NEC 800x600 NL8060BC31-01C. LVDS Flat Panel Support ListIf you would like to use LVDS Flat Panel with Vortex86SX / Vortex86DX series, please contact our regional sales to get ICOP-0096 information or visit ICOP website:/pddetail.aspx?id=65&pid=4ICOP–0096: 18-bit TFT to LVDS converter and Cable-LVDS-30: LVDS Cable 30cmApproved LVDS Flat Panel ListSize Brand Resolution Model No.3.5” PVI 640x480 PD035VL15” PVI 640x480 PD050VL16.5” AUO 640x480 G065VN018.4” AUO 800x600 G084SN038.9” AUO 1024x600 A089SW018.9” CPT 1024x600 CLAA089NA0ACW10.4” AUO 800x600 G104SN0212.1” AUO 800x600 G121SN0115” AUO 1024x768 G150XG01D. Flat Panel Hardware Setting:The Vortex86SX-6155-V2 offers the Hardware setting for the various TFT LCD Flat Panels support and please make sure the jumper setting (J26~J31) before you connect the LCD.Display type setupConnector LCD 1-2 2-3J26 C J27 CJ28 X XJ29 X XJ30 CJ31 CNote: "C" means close; "X" means openE. Flat Panel Wiring and LightingHardwareBefore you connect the TFT LCD Flat Panel with Vortex86SX-6155-V2, please make sure that the input Voltage of LCD is +3.3V or NotBIOSPlease contact or e-mail our regional sales to get the special BIOS for the any TFT LCD Flat Panels.Wiring LCD CablePlease refer to Page 20 (J25: LCD connector) and Page 30~35. Or for more LCD lighting and integration service, please contact our regional sales or mail to *************.tw ,if you have any questions.F. TCP/IP library for DOS real modeDSock is a TCP/IP library for DOS real mode, which is used by RSIP. It provides simple C functions for programmer to write Internet applications. ICOP also provide Internet examples using DSock: BOOTP/DHCP, FTP server, SMTP client/server, HTTP server, TELNET server, Talk client/server, etc.DSock provides a lot of example source code. Programmer can add Internet functions to their project easily and save development time. With a utility "MakeROM”, programmer also can make a ROM image to fit their application, those examples can be seen in the following Application systems: Mity-Mite Serial Server,Web Camera Tiny Server and RSIP Serial Server.DSock is free for All ICOP products using M6117D/Vortex86/Vortex86SX/Vortex86DX CPU and ICOP also provide the business version of DSock for those customers who are using other x86 CPUs.If you would like to use DSock or business version of DSock, Please mail to *************.tw or contact your regional sales.Please download the trial DSock software and Utilities from our website:/tech/dmp-lib/dsock/G. BIOS Default settingIf the system cannot be booted after BIOS changes are made, Please follow below procedures in order to restore the CMOS as default setting.Press “End” Key, when the power onPress <Del> to enter the AMI BIOS setupPress “F9” to Load Optimized DefaultsPress “F10” to Save configuration changes and exit setupWarrantyThis product is warranted to be in good working order for a period of one year from the date of purchase. Should this product fail to be in good working order at any time during this period, we will, at our option, replace or repair it at no additional charge except as set forth in the following terms. This warranty does not apply to products damaged by misuse, modifications, accident or disaster. Vendor assumes no liability for any damages, lost profits, lost savings or any other incidental or consequential damage resulting from the use, misuse of, originality to use this product. Vendor will not be liable for any claim made by any other related party. Return authorization must be obtained from the vendor before returned merchandise will be accepted. Authorization can be obtained by calling or faxing the vendor and requesting a Return Merchandise Authorization (RMA) number. Returned goods should always be accompanied by a clear problem description.Vortex86SX-6155-V2 Vortex86SX™PC/104 CPU Module 38。

用户手册DLP 投影仪使用产品前请阅读使用说明。

保留备用。

BF50NST-GLBF60PST-GLP/NO : SAC37813575 (2112-REV00)版权 © 2021 乐金电子（中国）有限公司版权所有。

2中文目录许可证 3开源软件提示信息 4安全预防措施 5准备工作 17安装 25遥控器 34连接设备 37规格 43标志 49故障排除 503中文许可证不同型号所支持的许可证可能会有所不同。

有关许可证的详细信息，请访问 。

HDMI、HDMI高清晰度多媒体接口以及HDMI标志是HDMI Licensing Administrator, Inc.在美国和其他国家的商标或注册商标。

本产品经过杜比实验室的许可而制造。

杜比, 杜比视界，杜比音效，杜比全景声，和双 D 符号是杜比实验室的注册商标。

有关 DTS 专利，请参阅 。

在获得 DTS Licensing Limited 许可的条件下制造。

DTS、符号、DTS 与符号同时出现、DTS 2.0 Channel、DTS 2.0+Digital Out、DTS-HD 和 DTS Virtual:X 是 DTS, Inc. 在美国和/或其他国家/地区的注册商标或商标。

© DTS, Inc. 保留所有权利。

注意• 所示的图像可能与您的投影仪有所不同。

• 投影仪的 OSD（在屏显示）可能与此手册的显示略有不同。

4中文开源软件提示信息为取得本产品内搭载的 GPL、LGPL、MPL 及其他开源证书下的源代码，请您访问 https:// 。

除源代码以外，所有相关的许可条款、免责声明和版权通知均可供下载。

LG Electronics 也可以 CD-ROM 的形式为您提供开源代码,如有需要,请发送电子邮件至******************,仅收取执行配送的费用（如介质费用、运输费和手续费）。

此报价从该产品出厂之日起，三年内有效。

此报价对收到本信息的任何人有效。

CW8060INFORMATION IS SPECIFIC TO OUR PRODUCTS AND CAN CAUSE DAMAGE IF USED WITH NONE COMPATIBLE PRODUCTS SO PLEASECHECK WITH YOUR SUPPLIER FOR COMPATIBILITYThese drawings are supplied as a guide no guarantees are implied or given.CW8060 Stepper Motor DriverThe CW8060 Stepping Motor DriverOverview:Application:It is suitable for a variety of large-scale automation equipment and instruments, such as high end CNC machines, retrofitting projects labeling machines, cutting machines,packing machines, plotters, engraving machines and anywhere high performance and high transfer of power is required.The CW8060 microstepping driver design philosophy is based on advanced digital current control technology, with continuous monitoring of output to give smooth and reliable microstepping. Very versatile input power capability can be used with toroidal or similar transformer directly all internal rectification and smoothing built into CW8060, also can be used with Switchmode PSU operating voltage range is 24VDC-80VDC maximum and precautions taken not to exceed these values and consideration for input line variations and overvoltage generation by Switchmode PSU's for current regulation need to be factored in, if in doubt contact technical support team. Driver can be used with two-phase or four-phase (wired in iseries or Parallel) hybrid stepper motors up to 6.0A. Due to the adoption of theadvanced anti-noise sound control method, it can significantly reduce the noise and vibration during operation; it uses full current PWM control method, and featuresstable operation, low noise, low vibration and low temperature rise of motor. It has 16levels of microstepping, the maximum number of microsteps is 1/256 (step number is 51200 steps/rev can be useful to reduce vibration). Current range is 2.0A~6.0A, the output current is 8 steps; it has automatic semi-flow, self-test, overvoltage,under-voltage and over-current protection functions built in.CW80602-Phase stepping Motor DriverSwitch Choice:(¡ON=0，OFF=1¡)1、Microstepping choice:SW500000000111111SW601010101010101SW700110011001100SW800001111000011Micro 1/21/41/81/161/321/641/1281/2561/51/101/251/501/1251/2502、Current choice ：SW101010101SW200110011SW300001111Current （A ） 2.002.573.14 3.714.28 4.865.436.003、Full current or half current choice ：SW4：0＝Full current ；1＝half currentOutput Current Setting:Users can set the drive output current by SW1-SW3 three dip switches, only change settings when unit is powered down and on next power up your new settings will take effect. The setting of the specific output current, please refer to the illustrations of the drive panel figure due to high efficiency of these drivers stepper temperature maybe hotter than hobbyist is used to 50 to 60 oC if this is higher than you feel comfortable with just reduce current setting .Microstep Setting:Users can set the drive Microstep by SW5-SW8 four dip switches. The setting of the specific Micro-step subdivision, please refer to the illustrations of the drive panel figure. Steps / rev = 200 * microstep for the majority of steppers check with your manufacturer. Imperial and Metric values make for matching Imperial and Metric ballscrews so values are rounded but this is not essential. As well as giving increase resolution (8 to 10 microsteps) if application has excess torque is available you can use higher values to give smother operation.Automatic half current function:Users can set the drive half flow function by SW4 to "1" indicates that the quiescent current is reduced to half of the dynamic current set by the operator, this takes effect 0.5 seconds after the end of the step pulse.SW4 to "0" indicates that the quiescent current and the dynamic current is the same. Users should set SW4 to "1", if possible in order to reduce motor and drive heating and improve power consumption.Signal interfaces:CP+ and CP- is the positive and negative side of control pulse signalCW + and CW- is the positive and negative side of direction signalEN + and EN- is the positive and negative side of enable signal (can be left open). Motor interfaces:A + and A- is connected to a phase winding of motor;B + and B- is connected to another phase winding of motor. If you need to reversed, one of the phase windings can be reversed or reversed in your control software. Power interfaces:Recommended operating voltage is 24VDC-80VDC, and precautions taken not to exceed these absolute maximum values if in doubt please ask.Indicator lights:There are two indicator lights Power green and red when there is over-voltage or over-current fault, power down system and clear fault condition and when the drive fault is cleared, re-power the red light will be off if all faults have been rectified.Signal interface details:The internal interface of the CW8060 stepping motor drive are isolated by the optocouplers and built in resistor for 5Volt operation compatible with our range of breakout boards.Some examples of external resistor value for different voltages are shown below and required to limit current to a safe value for normal operation in the figure is an external current limiting resistor. The optocouplers give isolation and noise immunity.Outline and installation size (unit: mm)Drive Dimensions:150X99X48mm, please refer to dimensions diagram below.。

目录1 云终端简介.............................................................................................................................. -2 -1.1 云终端........................................................................................................................... - 2 -1.2 云终端产品参数........................................................................................................... - 3 -1.3 云终端的部署............................................................................................................... - 4 -1.4系统需求........................................................................................................................ - 5 -1.5 服务器软件安装........................................................................................................... - 6 -2 启动云终端............................................................................................................................ - 17 -2.1 启动前的准备............................................................................................................. - 17 -2.2 安装云终端................................................................................................................. - 18 -2.2.1 安装前准备...................................................................................................... - 18 -2.2.2云终端新建用户和监控................................................................................... - 19 -2.3 使用云终端................................................................................................................. - 20 -2.4 模式切换..................................................................................................................... - 21 -2.4.1 共享计算模式到MiniPC 模式 ..................................................................... - 22 -2.4.2 MiniPC 模式到共享计算模式 ........................................................................ - 22 -3 共享计算模式........................................................................................................................ - 22 -3.1 连接服务器................................................................................................................. - 23 -3.2 互联网浏览器............................................................................................................. - 24 -3.3 办公软件..................................................................................................................... - 24 -3.4 媒体播放器................................................................................................................. - 25 -3.5 系统设置..................................................................................................................... - 25 -3.6本地桌面...................................................................................................................... - 39 -4.MiniPC模式........................................................................................................................... - 39 -4.1 远程桌面连接............................................................................................................. - 39 -4.2 移动硬盘或U盘........................................................................................................ - 40 -4.3 显示属性..................................................................................................................... - 41 -4.4 屏幕键盘..................................................................................................................... - 41 -4.5 手写设置..................................................................................................................... - 42 -5. 常见问题解答....................................................................................................................... - 42 -云终端T680W实物图片云终端T680实物图片云终端简介1.1 云终端云终端是一种精巧别致的网络计算机，其外观如图1-1 所示。

T80系列控制器简易操作手册目录一、操作画面 (2)二、操作步骤 (3)1.准备启动 (3)2.设置目标转速 (3)3.升降负荷 (4)1>CV阀控 (4)2>功控 (4)3>主汽压控 (5)三、参数设置与功能选择 (6)四、常规伺服阀的调试方法 (9)一、操作画面操作员画面主要分以下四个画面，汽机参数，测点清单，电调试验，电调主控. 其中汽机参数，测点清单，电调试验三个画面的数据须工程师权限才允许操作修改。

如图1-1，2，3，4。

图 1-1.汽机参数图 1-2.测点清单图 1-3.电调试验图 1-4.电调主控二、操作步骤1.启动准备在现场进行挂闸，并且开启主汽门，T80画面相应的状态会改变，外部设备发允许启动信号，使“允许启动”灯亮。

此时点击电调主控画面的运行按钮，转速控制面板亮（转速框图由灰色变为蓝色）。

机组已进入等待冲转状态。

2.设置目标转速机组挂闸进入等待冲转状态后，（注：此时此框图为蓝色）转速控制栏在转速控制栏目标转速输入目标转速（一般设定为3000 r/min）值。

也可以设置为其他任何非临界区的转速值。

首次起机建议先给500转，再1200，然后2500，以此类推。

目标转速设定后，给定转速将以默认的升速率向目标转速靠近；机组开始冲转；司机可根据实际情况在升速率输入框内修改升速率，允许取值范围为0~800最大升速率 r/min/min；（建议慢些100~200）。

随着给定转速的增加，总阀位给定增加，油动机开启，机组转速增加；暖机时间到或点击“停止暖机”按钮后继续升速；当需要保持当前转速时，点击“给定保持”。

3.升降负荷1>CV阀控并网带初负荷后，操作员可通过点按“CV阀控”CV阀控控制栏栏内的增、减按钮（即单箭头与双箭头键，改变总阀位给定值单位为%），从而控制调门开度，来控制负荷。

2>功控功控控制栏功控投入：在电网要求机组维持负荷不变时，可投入功率反馈控制。

ARM8060嵌入式主板说明书北京阿尔泰科技发展有限公司Beijing Art Technology Development Co.,Ltd.！安全须知电气方面安全性为避免可能的电击造成严重损害，在移动主板之前，请先将主板的电源切断。

当您要加入硬件设备到系统中或者要移除系统中的硬件设备时，请务必先连接该设备的信号线，然后再连接电源线。

请确定电源的电压设置已调整到所规定的电压标准值。

操作方面的安全性在您安装主板以及加入硬件设备之前，请务必详细阅读本手册所提供的相关信息。

在使用本产品之前，请确定所有的排线、电源线都正确地连接好。

若您发现有任何重大的瑕疵，请尽快联系我们或您的经销商。

为避免发生电气短路情形，请务必将所有没用到的螺丝、回形针及其它零件收好，不要遗留在主板上。

灰尘、湿气以及剧烈的温度变化都会影响主板的使用寿命，因此请尽量避免放置在这些地方。

当操作系统启动过程中，请勿断电，为避免损坏主板芯片系统运行过程中，防止静电，最好不要用手接触主板若在本产品使用上有任何的技术性问题，请和我们的技术支持人员联系。

目录目录 (2)1．产品简介 (3)1.1产品概述 (3)1.2 产品特点 .................................................................................................................. 错误！未定义书签。

2产品特性 (11)2.1跳线说明 (11)2.2 外围设备接口连接 (11)2.3 软件特性 ................................................................................................................ 错误！未定义书签。

3．电气参数及机械特性 (18)附录A 订购信息 (19)附录B 应用程序开发环境 (19)1．产品简介1.1产品概述ARM8060是北京阿尔泰科技发展有限公司基于Atmel公司ARM926EJ-S内核的AT91SAM9261处理器，结合PC104总线规范设计的一款具有极高性价比、结构和尺寸极其紧凑并且功耗极低的工业级嵌入式主板，其上运行嵌入式Linux 或WinCE操作系统，可以处理多种计算任务。