PD-IM-7604-4M/T4HUser Guide PD-IM-7604-4MH and PD-IM-7604-4T4H Four 2-Pair Portsand Four 4-Pair Ports Evaluation BoardsJune 20191Revision History (1)1.1Revision 2.0 (1)1.2Revision 1.0 (1)2Product Overview (2)2.1Evaluation System Features (4)2.2Evaluation System Interfaces and Connections (4)2.2.1RJ45 Connectors (5)2.2.2V IN Connector (6)2.2.3Isolated USB Interface (6)2.3Test Points (7)2.4LED Indication (7)2.5Physical Characteristics (8)2.6Electrical Characteristics (8)3Installation and Settings (9)3.1Initial Configuration (9)4Reference Documents (11)5Ordering Information (12)The revision history describes the changes that were implemented in the document. The changes arelisted by revision, starting with the most current publication.1.1Revision2.0Revision 2.0 was published in June 2019 with minor editorial corrections.1.2Revision 1.0Revision 1.0 was first published in November 2017. It was the first publication of this document.The PD-IM-7604-4M/T4H evaluation board is developed based on two PD69208M/PD69208T4-PD69204T4 and PD69200 chipsets, and demonstrates the operation of four 4-pair ports and four 2-pairports systems.Microsemi's PD69208M/PD69208T4/PD69204T4 Power over Ethernet (PoE) manager IC integratespower, analog, and state-of-the-art logic into a single 56-pin, plastic QFN package. The device is used inEthernet switches and midspans to allow network devices to share power and data over the same cable.The PD69208M/PD69208T4 device is an 8-port and PD69204T4 device is a 4-port, mixed-signal, and high-voltage PoE driver. With the PD69200 external MCU, it performs as a PSE system. Microsemi's PD69200PoE controller is a cost-effective and pre-programmed MCU designed to implement enhanced mode.The PD69208M/PD69208T4/PD69204T4 and PD69200 chipset supports PoE powered device (PD)detection, power-up, and protection according to IEEE standards as well as legacy/pre-standard PDdetection. It provides real-time PD protection through the following mechanisms such as, overload,under-load, over-voltage, over-temperature, and short-circuit, and enables operation in a standalonemode. It also executes all real-time functions as specified in IEEE 802.3at and IEEE 802.3bt draft 3.0standards, including PD detection (AF and AT).PD69208M/PD69208T4/PD69204T4 supports supply voltages between 32 V and 57 V without additionalpower sources. A system that powers over four pairs can be implemented by combining 2 ports ofPD69208M/T4 and PD69204T4, enabling an extra feature for simple and low-cost high-power PDdevices. Ongoing monitoring of system parameters for the host software is available throughcommunication. Internal thermal protection is implemented in the chip. The PD69208M/PD69208T4Ω /PD69204T4 is a low power dissipation device that uses internal MOSFETs and internal 100 m senseresistors.The PD69200 features an ESPI bus for each PD69208M/PD69208T4/PD69204T4. It is based onFreescale's Kinetis_L family MKL15Z128VFM4 embedded with an ARM Cortex™-M0+core. The PD69200utilizes an I C or UART interface to the host CPU. It is designed to support software field-upgradable2through the communication interface.The evaluation system provides designers with the required environment to evaluate the performanceand implementation of the following.PD69204T4 (four ports) and PD69208T4 (eight ports) PoE managers and PD69200 PoE controller (inboard PD-IM-7604-4T4H)PD69208M (eight ports) PoE manager and PD69200 PoE controller (in board PD-IM-7604-4MH)The evaluation board, shown in the following figure, enables PoE designers to evaluate Microsemi's PoE solution with flexibility and easy configuration. The application circuit of two PD69208M/PD69208T4-PD69204T4 and PD69200 chipset is compact in size (highlighted in the white box on board).Figure 1 • PD-IM-7604-4M/T4H Evaluation System Block DiagramInput supply to the board is DC and it can be fed through the V connector (seeIN Electrical Characteristics (see page 8)for the input voltage range). The auxiliary power supply (5 V and 3.3 V) for the PD69208M /PD69208T4/PD69204T4 is generated internally and the auxiliary power supply (3.3 V) for the PD69200–MCU is generated using a 3.3 V isolated DC DC converter.The board communicates with the host environment using UART communication, available through a USB connector (U11). For this connection, a driver for CP210x should be installed. The driver can be /products/mcu/Pages/USBtoUARTBridgeVCPDrivers.aspx downloaded from .A dedicated reset push button (SW1) is provided for resetting the PoE controller. The board consists of eight output ports, of which four are 2-pair ports and the remaining four are 4-pair ports.Test Points (see page 7)The board consists of different test points (for more information, see ). TheLED Indication (see page 7) board also provides different LED indications (for more information, see ).Figure 2 • PD-IM-7604-4M/T4H Evaluation Board2.1Evaluation System FeaturesThe evaluation system has the following features.Two gangs (each contains four RJ45 connectors)Switch domain isolated from PoE domainSwitch domain USB interfacePoE controller manual resetLED status indication for all the ports (LED stream)Requires single power source only0 °C to 40 °C working temperatureRoHS compliant2.2Evaluation System Interfaces and ConnectionsThe evaluation system interfaces and connectors are listed in the following table.Table 1 • Evaluation board ConnectorsConnector Name DescriptionSerialNumberEight RJ45 ports are connected to the powered device load1J3, J4RJ45connectors2J1V connectorMAININ The DC in (V) connection is used to power the evaluation board 3U11Isolated USB The USB communication, coming from the hosting system (U11), convertedto UART and directed to the PoE controllerThere are two dedicated RJ45 connectors. Each contains four RJ45 ports, so there are eight ports in total. The four ports of J3 are 2-pair ports (port numbers 0, 1, 2, and 3) and the power connections of the port are listed in the following table.Table 2 • RJ45 Connectors 2-pair PortPin Number (each RJ45)Signal Name Description4, 5SPARE - Vport_Pos PoE's positive spare port7, 8SPARE - Vport_Neg PoE's negative spare portThe four ports of J4 are 4-pair ports (port numbers 4, 5, 6, and 7) and the power connections of the port are listed in the following table.Table 3 • RJ45 Connectors 4-pair PortPin Number (each RJ45)Signal Name Description1, 2DATA - Vport_Neg PoE's negative data port3, 6DATA - Vport_Pos PoE's positive data port4, 5SPARE - Vport_Pos PoE's positive spare port7, 8SPARE - Vport_Neg PoE's negative spare portManufacturer: AmphenolManufacturer part number: RJHSE508104The following figure shows the RJ45 connectors.Figure 3 • RJ45 ConnectorsThe DC input (V) connection is used for powering the evaluation system. The recommended inputMAINvoltage range is 44 V DC > V > 57 V DC. The input connector is rated for 5 A (See forMAIN Evaluation Boardthe V connector).INTable 4 • V IN ConnectorPin Number Signal Name Description1V MAIN Main positive voltage (referenced to GND_ANALOG)2GND_ANALOG Analog ground3GND_ANALOG Analog groundManufacturer: SWITCHCRAFTManufacturer part number: RAPC722XThe polarity of the V connector is as shown in the following figure.INFigure 4 • Power Supply Cable Polarity2.2.3Isolated USB InterfaceThis interface supplies USB communication coming from the hosting system (U11), converted to UARTcommunication (See for the isolated USB connector).Evaluation BoardTable 5 • Isolated USB InterfacePin Number Signal Name Description1VBUS Voltage supply from USB bus2D–Dedicated USB signal3D+Dedicated USB signal4GND_F Floating groundManufacturer: SamtecManufacture part number: USB-B-S-S-B-TH2.3Test PointsThe following table lists the test points in the evaluation board.Table 6 • Test PointsDesignation DescriptionTP1Connected to power good pin, PG3TP2Connected to power good pin, PG2TP3Connected to power good pin, PG1TP4Connected to power good pin, PG0TP5PD69200 supply (3.3 V) test pointTP6PD69200 ground test pointTP7I C bus serial data (SDA)2TP8I C bus serial clock (SCL)2h1 (+)Evaluation board positive input (V) test pointMAINh2 (–)Evaluation board input ground test point2.4LED IndicationThe evaluation board contains status indication LEDs, listed in the following table.Table 7 • LED IndicationDesignation DescriptionD2Input voltage indicationD3PoE controller 3.3 V indicationD4System OK indication; by default, turns on when input voltage is within operating rangeD5Interrupt indication; LED turns on when a pre-configured event is happeningApart from these LEDs, each RJ45 connector port contains a dedicated LED (green LED), which displaysthe status of the particular port.Table 8 • Port Status IndicationsPort LEDColorPort Load Conditions Port VoltageOff Inactive load or unplugged load Power to port is disconnected, no DC voltage is presenton port output linesGreen Active load is plugged in and complies withnormal load conditionsContinuous nominal DC voltage is presentBlinking green Overload, short circuit, or power management Power to port is disconnected, no DC voltage is presenton port output lines2.5Physical CharacteristicsThe mechanical dimensions of the board are 180 mm × 60 mm × 16 mm (L × W × H).2.6Electrical CharacteristicsThe following table lists the electrical characteristics of the evaluation system.Table 9 • Electrical CharacteristicsParameter Minimum Maximum UnitsMain DC supply V MAIN4457VThis section describes the steps required for installing and operating the PD-IM-7604-4M/T4Hevaluation system. Take the following precautions before starting the installation.Ensure that the power supply of the board is turned on before the peripheral devices are turned on.Ensure that all the required peripherals are connected before powering the board.Ensure that power bank15 is set to 200 W.Ensure the correct polarity of the power supply cable. The polarity of the power supply cable is asshown in .Power Supply Cable Polarity (see page 6)NoteConfirm that the evaluation board is properly configured prior to starting any operation. Formore information about the software and GUI used for enhanced mode operation, seeSoftware GUI User Guide,catalog number 06-0027-056.3.1Initial ConfigurationThe board based on PD69208T4 and PD69204T4 devices (ordering part number PD-IM-7604-4T4H) isconfigured with the following matrix.Table 10 • Port MatrixPort Identification Number Logical Port Physical Port (ALT-A)Physical Port (ALT-B)000255111255222255333255444555676689771011The board based on two PD69208M devices (ordering part number PD-IM-7604-4MH) is configured with the following matrix.Table 11 • Port MatrixPort Identification Number Logical Port Physical Port (ALT-A)Physical Port (ALT-B)0002551112552222553332554489551011661213771415The following documents can be obtained through Microsemi customer support. To access otherMicrosemi websitedocuments, visit the .IEEE 802.3af-2003 Standard, DTE Power via MDIIEEE 802.3at-2009 Standard, DTE Power via MDIPD69204T4 Datasheet (PD-000303601)PD69208M Datasheet (PD-000303451)PD69208T4 Datasheet (PD-000303603)Application Note 211: Designing a PD69208 48-port Enhanced PoE Systems and Layout DesignGuidelines (catalog number PD69208_AN_211) (PD-000300282)Technical Note 218: Interfacing LED Stream circuit with PD69200 (catalog numberPD69200_TN_218_PoE_LED_Stream_Interface)PD69200 Serial Communication Protocol User Guide (catalog number PD_69200_UG_COMM_PROT)Software GUI User Guide (catalog number 06-0027-056)The following table lists the ordering information for the PD-IM-7604-4MH/4T4H evaluation boards.Table 12 • Ordering informationOrdering Number DescriptionPD-IM-7604-4MH Four 2-pair and four 4-pair type-3 ports, the PD69208M-based enhanced evaluationboard supports up to 60 W (4-pair) with LED stream and is RoHS compliant.PD-IM-7604-4T4H Four 2-pair and four 4-pair type-4 ports, the PD69208T4/PD69204T4-based enhancedevaluation board supports up to 99 W (4-pair) with LED stream and is RoHS compliant.Microsemi HeadquartersOne Enterprise, Aliso Viejo,CA 92656 USAWithin the USA: +1 (800) 713-4113Outside the USA: +1 (949) 380-6100Sales: +1 (949) 380-6136Fax: +1 (949) 215-4996Email:***************************© 2019 Microsemi. All rights reserved. Microsemi and the Microsemi logo are trademarks of Microsemi Corporation. All other trademarks and service marks are the property of their respective owners.Microsemi makes no warranty, representation, or guarantee regarding the information contained herein or the suitability of its products and services for any particular purpose, nor does Microsemi assume any liability whatsoever arising out of the application or use of any product or circuit. The products sold hereunder and any other products sold by Microsemi have been subject to limited testing and should not be used in conjunction with mission-critical equipment or applications. Any performance specifications are believed to be reliable but are not verified, and Buyer must conduct and complete all performance and other testing of the products, alone and together with, or installed in, any end-products. Buyer shall not rely on any data and performance specifications or parameters provided by Microsemi. It is the Buyer's responsibility to independently determine suitability of any products and to test and verify the same. The information provided by Microsemi hereunder is provided "as is, where is" and with all faults, and the entire risk associated with such information is entirely with the Buyer. Microsemi does not grant, explicitly or implicitly, to any party any patent rights, licenses, or any other IP rights, whether with regard to such information itself or anything described by such information. Information provided in this document is proprietary to Microsemi, and Microsemi reserves the right to make any changes to the information in this document or to any products and services at any time without notice.Microsemi, a wholly owned subsidiary of Microchip Technology Inc. (Nasdaq: MCHP), offers a comprehensive portfolio of semiconductor and system solutions for aerospace & defense, communications, data center and industrial markets. Products include high-performance and radiation-hardened analog mixed-signal integrated circuits, FPGAs, SoCs and ASICs; power management products; timing and synchronization devices and precise time solutions, setting the world's standard for time; voice processing devices; RF solutions; discrete components; enterprise storage and communication solutions; security technologies and scalable anti-tamper products; Ethernet solutions; Power-over-Ethernet ICs and midspans; as well as custom design capabilities and services. Microsemi is headquartered in Aliso Viejo, California, and has approximately 4,800 employees globally. Learn more at www. .PD-000354473。
SPORT OPTICS PRICE GUIDE 2015Offering the ultimate level of optical and build quality to achieve a brilliant view of your subject.What you couldn’t see before is suddenly so close you can almost touch it.That’s because PENTAX premium level quality and clarity are within reach, at a price that’s within reach, too. Every Z-series model is built for critical observation. PENTAX: designed to delight the most demanding users. Designed to inspire the most dedicated enthusiasts.• Premium multi-layer coatings assure the maximum light transmission through the binocular. The result is bright, crisp, true-to-life images in the widest range of viewing conditions.• Specialized protective coating repels dust, water and grease to keep your optics clean and your image quality at its peak.• Magnesium alloy construction balances durability and weight. The lightweight design is built to handle rough and tumble conditions of life’s adventures. • Hybrid Aspherical lens elements provide exceptional edge-to-edge sharpness. This assures that items on the edge of your field of view are just as sharp as those in the center.• Phase coated roof prisms allow the maximum light transmission for sharp, high contrast images.• Waterproof and nitrogen-filled (JIS Class 6) to handle the most extreme weather conditions (submersible to 1m). CODE PRODUCT NAME UPC CODE DEALER NET UPP 62701ZD 8x43 ED027*********$699.95$999.00 62702ZD 10x43 ED027*********$769.95$1,099.00 62703ZD 10x50 ED027*********$804.95$1,149.00 62721ZD 8x43 WP027*********$419.95$599.00 62722ZD 10x43 WP027*********$454.95$649.00 62723ZD 10x50 WP027*********$524.95$749.00Superior quality full sized binoculars that are ideal for the widest range of lighting and weather conditions.Exceptional quality meets high-end expectations. Large objective lenses incorporated in the design allow for contrast-rich, bright viewing under all light conditions.• Large objective lens elements provide maximum light gathering capabilities and are perfect for use in low light conditions.• Premium multi-layer coatings assure the maximum light transmission through the binocular. The result is bright, crisp, true-to-life images in the widest range of viewing conditions.• Specialized protective coating repels dust, water and grease to keep your optics clean and your image quality at its peak. (SD Models Only)• Rigid body construction makes these binoculars extremely rugged to maintain optical alignment. This ensures comfortable viewing throughoutthe life of the product.• Waterproof and nitrogen-filled (JIS Class 6) to handle the most extreme weather conditions (submersible to 1m). CODE PRODUCT NAME UPC CODE DEALER NET UPP 62751SD 9x42 WP027*********$259.95$349.00 62761SD 8x42 WP027*********$174.95$249.00 62762SD 10x42 WP027*********$195.95$279.00 65871SP 8x40 WP027*********$111.95$159.00 65872SP 10x50 WP027*********$132.95$189.00 65873SP 12x50 WP027*********$139.95$199.00 65874SP 20x60 WP027*********$167.95$239.00 65902SP 8x40027075288720$54.95n/a 65903SP 10x50027075288737$59.95n/a 65904SP 12x50027075288744$64.95n/a 65905SP 16x50027075288751$67.95n/aFull-size performance in a compact-sized body. All A Series binoculars offer you impeccableviewing quality in a compact, portable and durable design, so you can enjoy carrying convenience without compromising performance.• Compact roof and porro prism models that balance small size and premium image quality. These binoculars are easily packable when small size and weight are critical but a high quality image is required.• Premium multi-layer coatings assure the maximum light transmission through the binocular. The result is bright, crisp, true-to-life images in the widest range of viewing conditions.• Durable construction includes fiber reinforced polycarbonate designs which combine light weight and rugged styling. The reinforced chassis isextremely rigid, but light enough to carry anywhere. • Waterproof and nitrogen-filled (JIS Class 6) to handle the most extreme weather conditions (submersible to 1m).Advanced compact models with premium quality features and build for all of life’s adventures.CODE PRODUCT NAME UPC CODE DEALER NET UPP 62791AD 9x32 WP 027*********$195.95$279.0062831AD 9x28 WP 027*********$139.95$199.0062851AD 8x36 WP 027*********$139.95n/a 62852AD 10x36 WP 027*********$146.95n/a 62881AD 8x25 WP 027*********$83.95n/a 62882AD 10x25 WP 027*********$90.95n/a 65931AP 8x30 WP 027*********$97.95n/a 65932AP 10x30 WP027*********$104.95n/aDon’t miss a moment. Indoors or out. PENTAX quality and clarity are within reach, at a price that’s within reach, too. These compact porro-prism models feature a dual-axis, single body design with synchronized eyepiece adjustment. Aspherical lens elements give you edge-to-edge sharpness. Clear images and clearly affordable.• Fully-multi-coated optics assure maximum light transmission resulting in high quality viewing. Every surface of every element is fully coated minimizing internal glare and flare and giving a bright clear view.• Unique Uni-body design enhances durability by locking objective lenses in a single housing and synchronizing the eyepiece movement. This minimizes moving parts and assures these binoculars will function properly and clearly for years to come.• Aspherical lens elements, which are critical in compact binoculars, provide exceptionaledge-to-edge sharpness. This assures that items on the edge of your field of view are just as sharp as those in the center.• The UP 8-16x21 Zoom and UP 10x21 and 8x21 models are offered in unique, attractive color options that match your personal style.Compact, durable models ideal foruse from the field to the theater.CODE PRODUCT NAME UPC CODE DEALER NET UPP61801UP 8x21 Black027*********$41.95n/a61802UP 8x21 Navy027*********$41.95n/a61803UP 8x21 Pink027*********$41.95n/a61804UP 10x21 BK027*********$44.95n/a61805UP 10x21 Navy027*********$44.95n/a61806UP 10x21 Pink027*********$44.95n/a61901UP 8x25027075288843$62.95n/a61902UP 10x25027075288850$69.95n/a61931UP 8x25 WP027*********$88.95n/a61932UP 10x25 WP027*********$98.95n/a61961UP 8-16x21 BLACK027*********$76.95n/a61962UP 8-16x21 Brown027*********$76.95n/a61963UP 8-16x21 Green027*********$76.95n/a62001PAPILIO II 6.5x21027075288911$94.95$129.0062002PAPILIO II 8.5x21027075288928$104.95$149.00• BaK-4 prisms provide clear, sharp images• Multi-Coating maximizes light transmission, clarity, and contrast • Wide field of view increases viewing comfort • Pocket size and feather light (6 ounces)CODE PRODUCT NAME UPC CODE DEALER NET UPP KB613938x21 Jupiter III Clam Pack027*********$25.95n/a• Available in 7x50 which gives the ideal magnification and objective lens diameter for viewing on or around water• Built-in Compass, with an easy to read compass scale, on liquid bearing for quick dampening• Ranging reticle to determine distance from object or object size from a distance • Nitrogen-filled, waterproof construction allow these binoculars to be used in the most extreme weather conditions• High-resolution phase-coated and super-reflective coated BaK-4 roof prisms provide high resolution, high contrast imagesCODE PRODUCT NAME UPC CODE DEALER NET UPP 880397x50 Marine w/ Built-in Compass & Case027*********$149.95n/a• Rubber covered exterior provides sure grip, protects internal mechanisms • Comfortable rubber eye cups adjust for use with or without glasses • Durable, polycarbonate construction withstands rough handling • Multi-Coating eliminates harmful ultraviolet rays, improves light • BaK-4 prisms allow more light for easier viewing in any conditionCODE PRODUCT NAME UPC CODE DEALER NET UPP 8803610x50 WA027*********$34.50n/a• Powerful 10x25 roof prism construction • High-resolution wide-angle design• Compact and rugged full metal body with rubber armoring • Waterproof for use in inclement weather conditions• Multi-coated lenses increase light transmission and color quality • Highest quality BaK-4 prisms for maximum light transmissionCODE PRODUCT NAME UPC CODE DEALER NET UPP 8803710x25 DCF WP027*********$34.50n/a• Fully-multi-coated optics assure maximum light transmission resulting in high quality viewing. Every surface of every element is fully coated minimizing internal glare and flare and giving a bright clear view.• Included macro viewing stand magnifies close up object bringing out the smallest details.CODE PRODUCT NAME UPC CODE DEALER NET UPP 880338x42 Monocular w/ Magnifier Stand027*********$104.95$129.00Jupiter III SeriesMarine10x5010x258x42 MonocularCODE PRODUCT NAME UPC CODE DEALER NET UPP 70511 SMC XW 3.5 (11/4” Tube) 027*********$270.95 $359.00 70512 SMC XW 5 (11/4” Tube) 027*********$270.95 $359.00 70513 SMC XW 7 (11/4” Tube) 027*********$270.95 $359.00 70514 SMC XW 10 (11/4” Tube) 027*********$270.95 $359.00 70515 SMC XW 14 (11/4” Tube) 027*********$270.95 $359.00 70516 SMC XW 20 (11/4” Tube) 027*********$270.95 $359.00 70509SMC WP Zoom (11/4” Tube)027*********$349.95$459.00CODE PRODUCT NAME UPC CODE DEALER NET UPP 70531 SMC XF 8.5 (11/4” Tube) 027*********$132.95 $179.00 70532 ESMC XF 12 (11/4” Tube) 027*********$132.95 $179.00 70530SMC XF Zoom (11/4” Tube)027*********$222.95$319.00CODE PRODUCT NAME UPC CODE DEALER NET UPP 70510PF-CA35 Camera Adapter027*********$313.95$419.00CODE PRODUCT NAME UPC CODE DEALER NET UPP 70930 PF-80ED with Field Case 027*********$631.95 $849.00 KU70114 PF-80ED w/Zoom Eyepiece 027********* $846.95 $1,099.00 70950 PF-80ED-A with Field Case 027*********$679.95 $899.00 KU70115PF-80ED-A w/Zoom Eyepiece027*********$896.95$1,149.00CODE PRODUCT NAME UPC CODE DEALER NET UPP 70966 PF-65ED II with Field Case 027********* $412.95 $579.00 KU70117PF-65ED II w/Zoom Eyepiece 027********* $613.95 $799.0070967 PF-65ED-A II with Field Case 027********* $465.95 $659.00 KU70118PF-65ED-A II w/Zoom Eyepiece027*********$656.95$849.00CODE PRODUCT NAME UPC CODE DEALER NET UPP 69552Tripod Adapter-U for U-series models w/ tripod socket 027*********$4.95 n/a 69553Tripod Adapter N for S & A-series models w/ tripod socket 027*********$14.95 n/a 69554TP-3 Tripod Adapter for Z, S, & A-series models w/ tripod socket027*********$19.95n/aXW EyepiecesCamera AdaptersPF-80EDSpotting ScopesXF EyepiecesTripod AdaptersPF-65ED II SpottingScopesZD 8X43 ED ZD 10X43 ED ZD 10X50 ED ZD 8X43 WP ZD 10X43 WP ZD 10X50 WP SD 9X42 WP SD 8X42 WP SD 10X42 WP SP 8X40 WP SP 10X50 WP SP 12X50 WP SP 20X60 WP SP 8X40SP 10X50SP 12X50SP 16X50 AD 9X32 WP AD 9X28 WP AD 8X36 WP AD 10X36 WP AD 8X25 WP AD 10X25 WP AP 8X30 WP AP 10X30 WP UP 8X21UP 10X21UP 8X25UP 10X25UP 8-16X21 PAPILIO II 6.5X21PAPILIO II 8.5X21 | ricoh-imaging.ca | © 2015 Ricoh Imaging Americas Corporation。
![理财产品说明书[002]](https://imgs-1438308264.cos.ap-hongkong.myqcloud.com/465179cc6bec0975f465e268.webp)
理财产品说明书一、产品概述特别风险提示★银行销售的理财产品与存款存在明显区别，理财非存款、产品有风险、投资须谨慎。
★本产品为非保本浮动收益型产品，兴业银行理财产品风险评级为低风险，面向具有一定风险承受能力的有、无投资经验客户销售。
★兴业银行对本理财产品的本金和收益不提供保证承诺。
本理财产品在发生不利情况下（可能但不一定发生），投资者可能无法取得收益，并可能面临损失本金的风险。
投资者应认真阅读本说明书及风险揭示书风险揭示的内容，基于自身的独立判断进行投资决策。
★本理财产品说明书中的任何预计收益、参考收益、测算收益或类似表述均属不具二、投资范围1、本系列理财产品主要投资范围包括但不限于：（1）同业拆借、债券回购等货币市场工具，银行存款及其它银行间资金融通工具；（2）国债、政策性金融债、央行票据、短期融资券、中期票据、企业债、公司债等银行间、交易所市场债券及债务融资工具，其它固定收益类短期投资工具；（3） 符合监管机构规定的信托计划（受益权）等其它金融资产及其组合。
2、各投资资产种类的投资比例上述资产或资产组合信用级别较高，流动性较好，且符合兴业银行授权授信要求。
若产品所配置的信托计划（受益权）等其它金融资产的存续期限与理财期限不一致（该等资产期限长于理财期限），则存在期限错配的低流动性资产配置比例不高于70%。
3、特别提示：兴业银行将本着诚实信用、谨慎勤勉的原则，在规定的范围内运用理财资金进行投资，本产品如因市场变化、未达到或超过计划募集额等因素，投资比例可在不影响客户预期收益、产品风险评级的前提下合理浮动。
理财产品起始日的具体投资资产种类及比例将在产品成立公告中进行披露。
三、提前终止在理财产品投资运作期间内，客户无权要求提前终止该理财产品；当相关政策出现重大调整、市场出现剧烈波动、投资标的提前到期或发生其他兴业银行认为需要提前终止本理财产品等情况，银行有权部分或全部提前终止该款该期理财产品。
当银行决定提前终止本产品时，将在提前终止日前两个工作日通过代销机构营业网点，或兴业银行或代销机构的网站进行公示。
