电气专业毕业论文外文翻译分析解析

外文资料：Intellectual building electric protection and earth Summary : This text pass to several power supply earth systematic generalization introduction, is it suit as intellectual power supply earth system of building to screen, and has done comparatively exhaustive explanation and analysis to all kinds of earth measures should be takenned by it, electric protection that should adopt to the intellectual building and connecting the proper suggestion of local law proposition. Keyword:Load is balanced Electric potential form some earth , TN-S of datum point , defend static earth unify the earth body.Support distribution in the design , earth is it occupy important status to design systematically in building, because it concerns the dependability of the electric power system , the security . No matter how many buildings, include earth design systematically always in supplying power design. And, different with requirements of the building, functions of all kinds of equipment are different, earth systems are corresponding and different too. Especially after entering the 1990s, a large number of intelligent appearance of building design and get a lot of new contents out of systematically earth. In daily several person who connects place, which kind be suit the intelligent building ? We might as well analyse several kinds of earth systems .1.TN-C systemTN-C system call that into three-phase Line four system, systematic neutral line N this protect earth PE unite two into one, generally called PEN line. Although this kind of earth system is high in sensitivity to the earth trouble, circuit economy is simple, but it is only suitable for and used in three-phase load in the more balanced place . In theintelligent building, single-phase load proportion relatively heavy, difficult to realize three-phase to be load balanced, disequilibrium electric current , PEN of line add because fluorescent lamp , brilliant floodgate person who in charge of high times of in harmony wave electric current that equipment cause that exist in the circuit, in it is not the trouble cases , will superpose at the N in neutral line , make the neutral line N voltage fluctuate, and electric current light and extremely unstable when being heavy, cause neutral some electric potential unstable to drift about earth. Not only will electrify equipment outer cover (connects with PEN line ) , cause the rights of the person unsafe, and unable to fetch to a suitable electric potential datum point, the accurate electronic equipment is unable to run accurately reliably. So TN-C earth system can't be regarded as the earth system of the intelligent building .2.TN-C-S systemTN-C-S system is by two earth composition systematically, first part It is TN-C system, second part It is TN-S system, connect with PE line and click on N line the boundary. This system is generally used in the place attracted by regional switchyard of power supply of the building, enter family adopt TN-C system , enter households of place make repeated earth , enter after the family turning into TN-S system. Have already made analysis in front of TN-C system. The characteristic of TN-S system is: Neutral line N protect earth connection PE after grounding together while entering the family , can't have any electric connection. In this system, the neutral line N regular meeting protects the earth connection PE source without electricity with electricity. Equipment outer cover and metal component that PE line connects are in system normal running, will not be with electricity all the time. So TN-S earth system has obviously improved the securities of people and thing . At the same time so long as we adopt the earth lead wire, draw from earth body some each, choose correct earth resistance valuemake electronic equipment obtain one electric potential datum point ,etc. measure together, then TN-C-S system can be regarded as a kind of earth system of the intelligent building.3.TN-S systemTN-S is a earth system that three-phase Line four added PE line. Building usually is it enter line adopt this system when turning distribution into independently to have. The characteristic of TN-S system is, neutral line N and protecting earth connection PE except in the voltage transformer is grounded neutrally more together a bit, Line two no longer has electric connection of any. Neutral line N belong to electrification, but PE with electricity line. It's time to be grounded the system and totally possessed the safe and reliable basic electric potential. So long as like TN-C-S earth system, takes the same technological measure, TN-S system can be used as the earth system of the intellectual building. If such electronic equipment as the computer ,etc. generally adopt this kind of earth system without special requirement .4.TT systemUsually call TT system the three-phase Line four earth system. This system supplies power to come from the place of the public electric wire netting dailily in the building. Characteristic, TT of system whether neutral line N protect earth connection PE have a bit electric to join, namely neutral some earth separate from that the line earth of PE is. When this system is in normal running, whether three-phase load is balanced, in case of neutral line N electrification, PE line will not be with electricity. Single-phase earth only at the trouble, protect earth to be low in sensitivity, the trouble can be cut off in time, the equipment outer cover is perhaps with electricity. TT system at the time of normal running is similar to TN-S system , can obtain the securities of people and thing and make the qualified basic earth electric potential too. With electric leakage appearance ofperson who protect of large capacity, should systematic to can regard intelligent earth system of building as more and more too. According to present situation, because the power of the public electric wire netting is of low quality , difficult to meet the requirement for intelligent equipment, so TT system is seldom adopted by the intelligent building.5.IT systemIT system three-phase the strategic hinterland of China earth system, system this voltage transformer neutral to ground or pass impedance earth a bit, have neutral line N , have only line voltage (380V), is it is it keep to press to have (220V), protect earth connection PE and is grounded independently each. System this advantage to when the earth , can make outer cover have larger trouble electric current as one phase, the system can run as usual . The shortcoming can not allot the neutral line N. So it is not suitable for the intelligent building with a large number of single-phase equipment .In the intelligent building, demand to protect earth equipment very much, there is strong electric equipment , weak electric equipment, and the conductive equipment and component not with electricity, must adopt effective protection earth under some normal situations. If adopt TN-C system , use the N line in TN-C system as the earth connection at the same time ; Is it together , join N line and PE line really stiff to get on to connect among the system in TN-S; Set up electronic direct current earth lead wire of equipment and then , receive direct current earth on the PE line directly; Some clear-cut to is it answer together to mix N line , PE line , direct current earth connection. The above methods do not accord with earth requirement , and wrong. Have analysed , in the intelligent building, there is more single-phase power consuming equipment in in the front, single-phase load is relatively great in specific gravity, three-phase load is usually uneven, so there is random electric current in the neutral line N. In addition, becauseadopt the fluorescent lamp to light in a large amount, the waves in harmony three times produced by it are superposed on the N line, have strengthened the electric current amount on the N line, if receive N line on the equipment outer cover , will cause shocking by electricity or fire accident ; If on connecting N line and PE line to receive the equipment outer cover in TN-S system, so dangerous and heavy, every receive equipment on the PE line, with electricity outer cover; Will expand the range which will shock by electricity the accident; Connect together except will take place above-mentioned dangers N line , PE line , direct current earth connection, the electronic equipment will be interfered being unable to work. So intelligent building should set up electronic direct current earth of equipment, exchanges earth, safe protection earth, and ordinary dyke thunder that building too should possess protect earth.Now, we continue analysing various kinds of earth measures which should be taken in intelligent building .1 .Whether defend thunder's earth: For is it channel earth into rapidly to flow thunder and lightning, taking preventing the thunder from hurting as purpose earth is it defend thunder's earth to call.There are a large amount of electronic equipment and wiring system in the intelligent building, such as the communication automated system, the fire reports to the police and fire control link the control system , the automated system of the building , monitoring systems of security personnel, office automated system, the closed-circuit TV system,etc., and their corresponding wiring system. By the look of building built, the roof of every storey in the building, the baseplate, the side wall, hang and is nearly covered with by various kinds of wiring while carrying. These electronic equipment and wiring system generally belong to and able to bear the grade of pressing low , defend and interfere expecting much , is most afraid of the part struck by lightning. No matterattack directly, bunch hit, is it can make electronic equipment the damage in various degree or interfere seriously to strike back. It designs to be must tight , reliable to intelligent dyke thunder earth of building. Intelligent all function earth of building, must in order to avoid thunder based on the system earth, set up tightly , intact dyke thunder structure.The intelligent building is mostly first class load, should design according to the protective measure of first class Fang thunder building , connect person who flash adopt needle is it is it connect person who flash to make up to take , is it is it adopt 25* 4 (mm ) zinc-plated flat-rolled steel make up net of ≤ 10* 10 (m ) in roof to take to take shelter from the thunder, this net and metal component of the roofing are joined electrically, make and join with the building column cap reinforcing bar electrically, guide and roll off the production line and utilize the reinforcing bar in the column cap, enclose the reinforcing bar of roof beam , the floor reinforcing bar and defending the thunder system to join , other wall all metal component should with defend thunder system join , column cap reinforcing bar connect with earth body too, make up the shape of enveloping with multi-layer shielding and defend the thunder system. Can is it is it damage floor equipment to strike by lightning , but also still can prevent the outside electromagnetism from interfering to prevent effectively like this.Earth resistance frequently of engineering of all kinds of dyke of thunder earth devices , should according to set thunder reaction terms at confirm generally. Defend if thunder device share one total earth at the network with job earth of electric equipment, earth resistance should accord with its minimum requirement .2.The exchanges is grounded: Some any of power system, direct passing special equipment (such as impedance, resistance ,etc.), make metal join , call work earth with earth.Job earth mean voltage transformer neutral a bit or neutral line (N line ) earth mainly. N line must spend copper core insulating line. There is wiring end son of the electric potential such as being auxiliary in the distribution , wait for the wiring end son of the electric potential generally in the case cupboard. Must notice , should wire the end son and can expose ; Can't with other earth system, such as direct current earth, shielding earth, defend static earth is it is it connect to mix to wait for; Can't connect with PE line either.In high-pressure system , adopt neutral some person who connects place can make earth relay protection accurate movement and dispel single-phase electric arc earth overvoltage. Can prevent the skew of voltage of zero preface , keep the three-phase voltage in a basic balance in some neutral earth, this is very meaningful to low-voltage system, can be convenient to use the single-phase power.3.Safe protection is grounded: Safe protection earth metal part and earth body with electricity make good metal join electric equipment. Namely power consuming equipment and some metal components near the equipment of building, join with PE thread, but forbid connecting PE line with N line.In the intelligent building, require there is very much earth equipment of safe protection , there is strong electric equipment , weak electric equipment, and some conductive equipment and component with electricity, must take safe protection earth measure. When insulation not doing the earth electric equipment of safe protection is damaged , its outer cover is possible with electricity. If the outer cover that the human body touches this electric equipment may be wounded or caused the life danger by the electricity. Among neutral power system that ground directly a bit, earth short out electric current pass personal, the earth flows back to a bit more neutrally; In a bit more neutrally power system not grounded directly , the earth electric current flows into theearth through the human body, and form thorough fare by electric capacity by circuit to ground, two situation these can lead to the fact the rights of the person get an electric shock.If the insulation which is equipped with the electric equipment of the earth device is damaged while electrifying outer cover , short out in the electric current and flow through two thorough fares of earth body and human body at the same time in earth, I =IL + IP, we know: In a parallel circuit, the electric current value of passing each branch road is in inverse proportion to size of the resistance.In the type: I - Electric current total value in the earth return circuitIL - Electric current flowing through along the earth bodyIP - Flow through electric current of the human bodyHave type can find out earth resistance little , flow through to little electric current have human body, human resistance usually is it ground than earth resistance through electric current of human body electric current of body have several hundred less flowing through too to have several hundred heavier. When earth resistance is extremely small, the electric current that remakable body flows nearly equals zero. Namely I≈IL. In fact, because earth resistance very little, earth short out electric current flow out of date produce press and lower very lightly, so equipment outer cover voltage in earth high. People stand while going to touch the outer cover of the equipment on the earth, the voltage that the human body bears is very low, it can not be dangerous.Is it protect earth device and reduce earth resistance of it to install additional , not only ensure the electric security of system of intelligent building, the effective measure operated effectively, it is not the essential means of equipment and personal security in the intelligent building that ensure too.4.Direct current is grounded: In a block of intelligent building , include a largenumber of computers , communication apparatus and automation equipment of building with computer. Importing to information in these electronic equipment, transmission information, change energy , amplify signal, logic movement, output information a series of course go on through little electric potential or little electric current fast, and will often carry on the work through the internet between the equipment. So in order to make its accuracy high, the stability is good, besides needing to have a steady power supply power, must also possess a steady basic electric potential . Can adopt bigger and sectionaller insulating copper core line as the lead wire , one end is connected with basic electric potential directly, another end support electronic equipment direct current earth. It is unsuitable to connect with PE line to deserve and go between , forbid connecting with N line.5.Whether shielding earth defend static earth: In the intelligent building, it is very important to design electromagnetic and compatibly, in order to avoid the dysfunctions of the equipment used, equipment can appear evenned to prevent from damage, form equipment of wiring system should can prevent inside oneself conduct and extraneous interference from. Or because of the coupling phenomenon between the wire in these production that interfere, or because of the electric capacity effect or inductance effect. Main source its superelevation voltage, high-power pieces of radio magnetic field, strike by lightning naturally and static discharge. Phenomenon these will is it send or receive very high to transmit equipment of frequency produce heavy interference very to used for designing. Is it must take the protective measure to equipment the to connect up , avoid the interference from various kinds of respects. Shielding and correct earth to prevent electromagnetic best protection method that interfere. Can connect the equipment outer cover with PE line ; Require both ends ofshielding pipeline and PE line to join reliably in shielding earth of the wire; Indoor shielding should a lot of some is joined with PE thread reliably. It is very important too to defend static interference. In clean, dry room, walking , mobile device of people, is it can produce a large amount of static to grit each. For example 10-20% environmental walking of middleman can gather volt of static voltages , have good earth in relative humidity, will not merely produce the interference to the electronic equipment , even will break the equipment chip . Bring static object or may produce object (insulator ) of static through lead static body and earth form electric earth of return circuit is it defend static earth to call. Defend static earth require of clean quiet dry environment, all equipment outer cover and getting indoor facility must with line many to join reliably a bit PE have.Earth device of intelligent building little and kind earth resistance have, independent dyke thunder prote ct earth resistance in conformity with ≤ 10Ω; Independent safe protection earth resistance is in conformity with ≤ 4Ω; Independent exchanges earth resistance is in conformity with ≤ 4Ω; The independent working earth resistance of direct current is in confo rmity with ≤ 4Ω; Defend static earth resistance demand ≤ 100Ω the same.Intelligent power supply earth system of building should adopt TN-S system , should adopt according to norm one a total one common to ground the device , namely unify the earth body. It is a earth electric potential datum point to unify the earth body , therefore draw various kinds of function earth lead wire separately, the way of the electric potential of utilize electric potential such as being total and auxiliarying etc. makes up an intact unified earth system.Generally, unify earth system usable pile reinforcing bar of building, and zinc-plated flat-rolled steel link an organic whole it with 40* 4 (mm), as the natural earth body. According to norm, should systematic defending thunder earthshare systematically , in conformity with ≤ 1Ωearth resistance its. If can not reach the requirement , must increase artificial earth body or adopt chemistry lower law of hindering , make ≤ 1Ω of earth resistance . In turn into distribution is i t wait for electric potential copper arrange always to set up , copper this arrange one end through construct post or reinforcing bar of baseplate connect with unified earth body, another end join with exchanges neutral line , earth of system separately through different connection end son, with is it make safe protection earth every equipment join , with defend thunder's system join to need, join with the insulating copper core earth connection needing to make the earth electronic equipment of direct current. Among intellectual mansion, because system adopt computer is it manage or use computer as job tool to participate in, should adopt some earth not single of so earth of it system and should taking electric potential measure. Single some earth is it protect earth , job earth , direct current earth separate each other at the equipment to mean, it is systematic to become independence each. Can draw three insulating ground terminal each other from cabinet , and then guide to always waiting for the electric potential copper to arrange having and is grounded together from the lead wire. Is it is it together , is it wait for electric potential copper is it have to arrange always to receive three earth with lead wire and then to bind to allow. This to mix earth in fact, this kind connect law to be unsafe to can is it interfere to produce also, the present norm is not allowed .中文翻译：智能楼宇的电气保护与接地摘要:本文通过对几种供电接地系统的概括介绍，筛选出适合作为智能楼宇的供电接地系统，并对其所应采取的各类接地措施作了较为详尽的说明与分析，对智能楼宇应采取的电气保护与接地方法提出了适当的建议。

标准文档外文翻译院（系）专业班级姓名学号指导教师年月日Programmable designed for electro-pneumatic systemscontrollerJohn F.WakerlyThis project deals with the study of electro-pneumatic systems and the programmable controller that provides an effective and easy way to control the sequence of the pneumatic actuators movement and the states of pneumatic system. The project of a specific controller for pneumatic applications join the study of automation design and the control processing of pneumatic systems with the electronic design based on microcontrollers to implement the resources of the controller.1. IntroductionThe automation systems that use electro-pneumatic technology are formed mainly by three kinds of elements: actuators or motors, sensors or buttons and control elements like valves. Nowadays, most of the control elements used to execute the logic of the system were substituted by the Programmable Logic Controller (PLC). Sensors and switches are plugged as inputs and the direct control valves for the actuators are plugged as outputs. An internal program executes all the logic necessary to the sequence of the movements, simulates other components like counter, timer and control the status of the system.With the use of the PLC, the project wins agility, because it is possible to create and simulate the system as many times as needed. Therefore, time can be saved, risk of mistakes reduced and complexity can be increased using the same elements.A conventional PLC, that is possible to find on the market from many companies, offers many resources to control not only pneumatic systems, but all kinds of system that uses electrical components. The PLC can be very versatile and robust to be applied in many kinds of application in the industry or even security system and automation of buildings.Because of those characteristics, in some applications the PLC offers to much resources that are not even used to control the system, electro-pneumatic system is one of this kind of application. The use of PLC, especially for small size systems, can be very expensive for the automation project.An alternative in this case is to create a specific controller that can offer the exactly size and resources that the project needs [3, 4]. This can be made using microcontrollers as the base of this controller.The controller, based on microcontroller, can be very specific and adapted to only one kind of machine or it can work as a generic controller that can be programmed as a usual PLC and work with logic that can be changed. All these characteristics depend on what is needed and how much experience the designer has with developing an electronic circuit and firmware for microcontroller. But the main advantage of design the controller with the microcontroller is that the designer has the total knowledge of his controller, which makes it possible to control the size of the controller, change the complexity and the application of it. It means that the project gets more independence from other companies, but at the same time the responsibility of the control of the system stays at the designer hands2. Electro-pneumatic systemOn automation system one can find three basic components mentioned before, plus a logic circuit that controls the system. An adequate technique is needed to project the logic circuit and integrate all the necessary components to execute the sequence of movements properly.For a simple direct sequence of movement an intuitive method can be used [1, 5], but for indirect or more complex sequences the intuition can generate a very complicated circuit and signal mistakes. It is necessary to use another method that can save time of the project, makea clean circuit, can eliminate occasional signal overlapping and redundant circuits. The presented method is called step-by-step or algorithmic [1, 5], it is valid for pneumatic and electro-pneumatic systems and it was used as a base in this work.The method consists of designing the systems based on standard circuits made for each change on the state of the actuators, these changes are called steps.The first part is to design those kinds of standard circuits for each step, the next task is to link the standard circuits and the last part is to connect the control elements that receive signals from sensors, switches and the previous movements, and give the air or electricity to the supply lines of each step. In Figs. 1 and 2 the standard circuits are drawn for pneumatic and electro-pneumatic system [8]. It is possible to see the relations with the previous and the next steps.3. The method applied inside the controllerThe result of the method presented before is a sequence of movements of the actuator that is well defined by steps. It means that each change on the position of the actuators is a new state of the system and the transition between states is called step.The standard circuit described before helps the designer to define the states of the systems and to define the condition to each change betweenthe states. In the end of the design, the system is defined by a sequencethat never chances and states that have the inputs and the outputs well defined. The inputs are the condition for the transition and the outputs are the result of the transition.All the configuration of those steps stays inside of the microcontroller and is executed the same way it was designed. The sequences of strings are programmed inside the controller with 5 bytes; each string has the configuration of one step of the process. There are two bytes for the inputs, one byte for the outputs and two more for the other configurations and auxiliary functions of the step. After programming, this sequence of strings is saved inside of a non-volatile memory of the microcontroller, so they can be read and executed.The controller task is not to work in the same way as a conventional PLC, but the purpose of it is to be an example of a versatile controller that is design for an specific area. A conventional PLC process the control of the system using a cycle where it makes an image of the inputs, execute all the conditions defined by the configuration programmed inside, and then update the state of the outputs. This controller works in a different way, where it read the configuration of the step, wait the condition of inputs to be satisfied, then update the state or the outputs and after that jump to the next step and start the process again.It can generate some limitations, as the fact that this controller cannot execute, inside the program, movements that must be repeated for some time, but this problem can be solved with some external logic components. Another limitation is that the controller cannot be applied on systems that have no sequence. These limitations are a characteristic of the system that must be analyzed for each application.4. Characteristics of the controllerThe controller is based on the MICROCHIP microcontroller PIC16F877 [6,7] with 40 pins, and it has all the resources needed for thisproject .It has enough pins for all the components, serial communication implemented in circuit, EEPROM memory to save all the configuration of the system and the sequence of steps. For the execution of the main program, it offers complete resources as timers and interruptions.The list of resources of the controller was created to explore all the capacity of the microcontroller to make it as complete as possible. During the step, the program chooses how to use the resources reading the configuration string of the step. This string has two bytes for digital inputs, one used as a mask and the other one used as a value expected. One byte is used to configure the outputs value. One bytes more is used for the internal timer , the analog input or time-out. The EEPROM memory inside is 256 bytes length that is enough to save the string of the steps, with this characteristic it is possible to save between 48 steps （Table 1）.The controller (Fig.3) has also a display and some buttons that are used with an interactive menu to program the sequence of steps and other configurations.4.1. Interaction componentsFor the real application the controller must have some elements to interact with the final user and to offer a complete monitoring of the system resources that are available to the designer while creating the logic control of the pneumatic system (Fig.3):•Interactive mode of work; function available on the main program for didactic purposes, the user gives the signal to execute the step. •LCD display, which shows the status of the system, values of inputs, outputs, timer and statistics of the sequence execution.•Beep to give important alerts, stop, start and emergency.• Leds to show power on and others to show the state of inputs and outputs.4.2. SecurityTo make the final application works property, a correct configuration to execute the steps in the right way is needed, but more then that itmust offer solutions in case of bad functioning or problems in the execution of the sequence. The controller offers the possibility to configure two internal virtual circuits that work in parallel to the principal. These two circuits can be used as emergency or reset buttons and can return the system to a certain state at any time [2]. There are two inputs that work with interruption to get an immediate access to these functions. It is possible to configure the position, the buttons and the value of time-out of the system.4.3. User interfaceThe sequence of strings can be programmed using the interface elements of the controller. A Computer interface can also be used to generate the user program easily. With a good documentation the final user can use the interface to configure the strings of bytes that define the steps of the sequence. But it is possible to create a program with visual resources that works as a translator to the user, it changes his work to the values that the controller understands.To implement the communication between the computer interface and the controller a simple protocol with check sum and number of bytes is the minimum requirements to guarantee the integrity of the data.4.4. FirmwareThe main loop works by reading the strings of the steps from the EEPROM memory that has all the information about the steps.In each step, the status of the system is saved on the memory and it is shown on the display too. Depending of the user configuration, it can use the interruption to work with the emergency circuit or time-out to keep the system safety. In Fig.4,a block diagram of micro controller main program is presented.5. Example of electro-pneumatic systemThe system is not a representation of a specific machine, but it is made with some common movements and components found in a real one. The system is composed of four actuators. The actuators A, B and C are double acting and D-single acting. Actuator A advances and stays in specified position till the end of the cycle, it could work fixing an object to the next action for example (Fig. 5) , it is the first step. When A reaches the end position, actuator C starts his work together with B, making as many cycles as possible during the advancing of B. It depends on how fastactuator B is advancing; the speed is regulated by a flowing control valve. It was the second step. B and C are examples of actuators working together, while B pushes an object slowly, C repeats its work for some time.When B reaches the final position, C stops immediately its cycle and comes back to the initial position. The actuator D is a single acting one with spring return and works together with the back of C, it is the third step. D works making very fast forward and backward movement, just one time. Its backward movement is the fourth step. D could be a tool to make a hole on the object.When D reaches the initial position, A and B return too, it is the fifth step.Fig. 6 shows the first part of the designing process where all the movements of each step should be defined [2]. (A+) means that the actuator A moves to the advanced position and (A−) to the initial position. The movements that happen at the same time are joined together in the same step. The system has five steps.These two representations of the system (Figs. 5 and 6) together are enough to describe correctly all the sequence. With them is possible to design the whole control circuit with the necessary logic components. But till this time, it is not a complete system, because it is missing some auxiliary elements that are not included in this draws because they work in parallel with the main sequence.These auxiliary elements give more function to the circuit and are very important to the final application; the most important of them is the parallel circuit linked with all the others steps. That circuit should be able to stop the sequence at any time and change the state of the actuators to a specific position. This kind of circuit can be used as a reset or emergency buttons.The next Figs. 7 and 8 show the result of using the method without the controller. These pictures are the electric diagram of the control circuit of the example, including sensors, buttons and the coils of the electrical valves.The auxiliary elements are included, like the automatic/manual switcher that permit a continuous work and the two start buttons that make the operator of a machine use their two hands to start the process, reducing the risk of accidents.6. Changing the example to a user programIn the previous chapter, the electro-pneumatic circuits were presented, used to begin the study of the requires to control a system that work with steps and must offer all the functional elements to be used in a real application. But, as explained above, using a PLC or this specific controller, the control becomes easier and the complexity can be increasealso.Table 2 shows a resume of the elements that are necessary to control the presented example.With the time diagram, the step sequence and the elements of the system described in Table 2 and Figs. 5 and 6 it is possible to create the configuration of the steps that can be sent to the controller (Tables 3 and 4).While using a conventional PLC, the user should pay attention to the logic of the circuit when drawing the electric diagram on the interface (Figs. 7 and 8), using the programmable controller, described in this work, the user must know only the concept o f the method and program only the configuration of each step.It means that, with a conventional PLC, the user must draw the relationbetween the lines and the draw makes it hard to differentiate the steps of the sequence. Normally, one needs to execute a simulation on the interface to find mistakes on the logicThe new programming allows that the configuration of the steps be separated, like described by the method. The sequence is defined by itself and the steps are described only by the inputs and outputs for each step.The structure of the configuration follows the order:1-byte: features of the step;2-byte: mask for the inputs;3-byte: value expected on the inputs;4-byte: value for the outputs;5-byte: value for the extra function.Table 5 shows how the user program is saved inside the controller, this is the program that describes the control of the example shown before.The sequence can be defined by 25 bytes. These bytes can be dividedin five strings with 5 bytes each that define each step of the sequence (Figs. 9 and 10).7. ConclusionThe controller developed for this work (Fig. 11) shows that it is possible to create a very useful programmable controller based on microcontroller. External memories or external timers were not used in case to explore the resources that the microcontroller offers inside. Outside the microcontroller, there are only components to implement the outputs, inputs, analog input, display for the interface and the serial communication.Using only the internal memory, it is possible to control a pneumatic system that has a sequence with 48 steps if all the resources for all steps are used, but it is possible to reach sixty steps in the case of a simpler system.The programming of the controller does not use PLC languages, but a configuration that is simple and intuitive. With electro-pneumatic system, the programming follows the same technique that was used before to design the system, but here the designer work s directly with the states or steps of the system.With a very simple machine language the designer can define all the configuration of the step using four or five bytes. It depends only on his experience to use all the resources of the controller.The controller task is not to work in the same way as a commercial PLC but the purpose of it is to be an example of a versatile controller that is designed for a specific area. Because of that, it is not possible to say which one works better; the system made with microcontroller is an alternative that works in a simple way.应用于电气系统的可编程序控制器约翰 F.维克里此项目主要是研究电气系统以及简单有效的控制气流发动机的程序和气流系统的状态。

电气工程与自动化毕业论文中英文资料外文翻译The Transformer on load ﹠Introduction to DC MachinesIt has been shown that a primary input voltage 1V can be transformed to any desired open-circuit secondary voltage 2E by a suitable choice of turns ratio. 2E is available for circulating a load current impedance. For the moment, a lagging power factor will be considered. The secondary current and the resulting ampere-turns 22N I will change the flux, tending to demagnetize the core, reduce m Φ and with it 1E . Because the primary leakage impedance drop is so low, a small alteration to 1Ewill cause an appreciable increase of primary current from 0I to a new value of 1Iequal to ()()i jX R E V ++111/. The extra primary current and ampere-turns nearly cancel the whole of the secondary ampere-turns. This being so , the mutual flux suffers only a slight modification and requires practically the same net ampere-turns 10N I as on no load. The total primary ampere-turns are increased by an amount 22N I necessary to neutralize the same amount of secondary ampere-turns. In thevector equation , 102211N I N I N I =+; alternatively, 221011N I N I N I -=. At full load,the current 0I is only about 5% of the full-load current and so 1I is nearly equalto 122/N N I . Because in mind that 2121/N N E E =, the input kV A which is approximately 11I E is also approximately equal to the output kV A, 22I E .The physical current has increased, and with in the primary leakage flux towhich it is proportional. The total flux linking the primary ,111Φ=Φ+Φ=Φm p , isshown unchanged because the total back e.m.f.,（dt d N E /111Φ-）is still equal and opposite to 1V . However, there has been a redistribution of flux and the mutual component has fallen due to the increase of 1Φ with 1I . Although the change is small, the secondary demand could not be met without a mutual flux and e.m.f.alteration to permit primary current to change. The net flux s Φlinking thesecondary winding has been further reduced by the establishment of secondaryleakage flux due to 2I , and this opposes m Φ. Although m Φ and 2Φ are indicatedseparately , they combine to one resultant in the core which will be downwards at theinstant shown. Thus the secondary terminal voltage is reduced to dt d N V S /22Φ-=which can be considered in two components, i.e. dt d N dt d N V m //2222Φ-Φ-=orvectorially 2222I jX E V -=. As for the primary, 2Φ is responsible for a substantiallyconstant secondary leakage inductance222222/Λ=ΦN i N . It will be noticed that the primary leakage flux is responsible for part of the change in the secondary terminal voltage due to its effects on the mutual flux. The two leakage fluxes are closely related; 2Φ, for example, by its demagnetizing action on m Φ has caused the changes on the primary side which led to the establishment of primary leakage flux.If a low enough leading power factor is considered, the total secondary flux and the mutual flux are increased causing the secondary terminal voltage to rise with load. p Φ is unchanged in magnitude from the no load condition since, neglecting resistance, it still has to provide a total back e.m.f. equal to 1V . It is virtually the same as 11Φ, though now produced by the combined effect of primary and secondary ampere-turns. The mutual flux must still change with load to give a change of 1E and permit more primary current to flow. 1E has increased this time but due to the vector combination with 1V there is still an increase of primary current.Two more points should be made about the figures. Firstly, a unity turns ratio has been assumed for convenience so that '21E E =. Secondly, the physical picture is drawn for a different instant of time from the vector diagrams which show 0=Φm , if the horizontal axis is taken as usual, to be the zero time reference. There are instants in the cycle when primary leakage flux is zero, when the secondary leakage flux is zero, and when primary and secondary leakage flux is zero, and when primary and secondary leakage fluxes are in the same sense.The equivalent circuit already derived for the transformer with the secondary terminals open, can easily be extended to cover the loaded secondary by the addition of the secondary resistance and leakage reactance.Practically all transformers have a turns ratio different from unity although such an arrangement is sometimes employed for the purposes of electrically isolating one circuit from another operating at the same voltage. To explain the case where 21N N ≠ the reaction of the secondary will be viewed from the primary winding. The reaction is experienced only in terms of the magnetizing force due to the secondary ampere-turns. There is no way of detecting from the primary side whether 2I is large and 2N small or vice versa, it is the product of current and turns which causesthe reaction. Consequently, a secondary winding can be replaced by any number of different equivalent windings and load circuits which will give rise to an identical reaction on the primary .It is clearly convenient to change the secondary winding to an equivalent winding having the same number of turns 1N as the primary.With 2N changes to 1N , since the e.m.f.s are proportional to turns, 2212)/('E N N E = which is the same as 1E .For current, since the reaction ampere turns must be unchanged 1222'''N I N I = must be equal to 22N I .i.e. 2122)/(I N N I =.For impedance , since any secondary voltage V becomes V N N )/(21, and secondary current I becomes I N N )/(12, then any secondary impedance, including load impedance, must becomeI V N N I V /)/('/'221=. Consequently,22212)/('R N N R = and 22212)/('X N N X = . If the primary turns are taken as reference turns, the process is called referring to the primary side.There are a few checks which can be made to see if the procedure outlined is valid.For example, the copper loss in the referred secondary winding must be the same as in the original secondary otherwise the primary would have to supply a differentloss power. ''222R I must be equal to 222R I . ）222122122/()/(N N R N N I •• does infact reduce to 222R I .Similarly the stored magnetic energy in the leakage field)2/1(2LI which is proportional to 22'X I will be found to check as ''22X I . The referred secondary 2212221222)/()/(''I E N N I N N E I E kVA =•==.The argument is sound, though at first it may have seemed suspect. In fact, if the actual secondary winding was removed physically from the core and replaced by the equivalent winding and load circuit designed to give the parameters 1N ,'2R ,'2X and '2I , measurements from the primary terminals would be unable to detect any difference in secondary ampere-turns, kVA demand or copper loss, under normal power frequency operation.There is no point in choosing any basis other than equal turns on primary andreferred secondary, but it is sometimes convenient to refer the primary to the secondary winding. In this case, if all the subscript 1’s are interchanged for the subscript 2’s, the necessary referring constants are easily found; e.g. 2'1R R ≈,21'X X ≈; similarly 1'2R R ≈ and 12'X X ≈.The equivalent circuit for the general case where 21N N ≠ except that m r hasbeen added to allow for iron loss and an ideal lossless transformation has been included before the secondary terminals to return '2V to 2V .All calculations of internal voltage and power losses are made before this ideal transformation is applied. The behaviour of a transformer as detected at both sets of terminals is the same as the behaviour detected at the corresponding terminals of this circuit when the appropriate parameters are inserted. The slightly different representation showing the coils 1N and 2N side by side with a core in between is only used for convenience. On the transformer itself, the coils are , of course , wound round the same core.Very little error is introduced if the magnetising branch is transferred to the primary terminals, but a few anomalies will arise. For example ,the current shown flowing through the primary impedance is no longer the whole of the primary current.The error is quite small since 0I is usually such a small fraction of 1I . Slightlydifferent answers may be obtained to a particular problem depending on whether or not allowance is made for this error. With this simplified circuit, the primary and referred secondary impedances can be added to give:221211)/(Re N N R R += and 221211)/(N N X X Xe +=It should be pointed out that the equivalent circuit as derived here is only valid for normal operation at power frequencies; capacitance effects must be taken into account whenever the rate of change of voltage would give rise to appreciablecapacitance currents, dt CdV I c /=. They are important at high voltages and atfrequencies much beyond 100 cycles/sec. A further point is not the only possible equivalent circuit even for power frequencies .An alternative , treating the transformer as a three-or four-terminal network, gives rise to a representation which is just as accurate and has some advantages for the circuit engineer who treats all devices as circuit elements with certain transfer properties. The circuit on this basiswould have a turns ratio having a phase shift as well as a magnitude change, and the impedances would not be the same as those of the windings. The circuit would not explain the phenomena within the device like the effects of saturation, so for an understanding of internal behaviour .There are two ways of looking at the equivalent circuit:(a) viewed from the primary as a sink but the referred load impedance connected across '2V ,or(b) viewed from the secondary as a source of constant voltage 1V with internal drops due to 1Re and 1Xe . The magnetizing branch is sometimes omitted in this representation and so the circuit reduces to a generator producing a constant voltage 1E (actually equal to 1V ) and having an internal impedance jX R + (actually equal to 11Re jXe +).In either case, the parameters could be referred to the secondary winding and this may save calculation time .The resistances and reactances can be obtained from two simple light load tests. Introduction to DC MachinesDC machines are characterized by their versatility. By means of various combination of shunt, series, and separately excited field windings they can be designed to display a wide variety of volt-ampere or speed-torque characteristics for both dynamic and steadystate operation. Because of the ease with which they can be controlled , systems of DC machines are often used in applications requiring a wide range of motor speeds or precise control of motor output.The essential features of a DC machine are shown schematically. The stator has salient poles and is excited by one or more field coils. The air-gap flux distribution created by the field winding is symmetrical about the centerline of the field poles. This axis is called the field axis or direct axis.As we know , the AC voltage generated in each rotating armature coil is converted to DC in the external armature terminals by means of a rotating commutator and stationary brushes to which the armature leads are connected. The commutator-brush combination forms a mechanical rectifier, resulting in a DCarmature voltage as well as an armature m.m.f. wave which is fixed in space. The brushes are located so that commutation occurs when the coil sides are in the neutral zone , midway between the field poles. The axis of the armature m.m.f. wave then in 90 electrical degrees from the axis of the field poles, i.e., in the quadrature axis. In the schematic representation the brushes are shown in quarature axis because this is the position of the coils to which they are connected. The armature m.m.f. wave then is along the brush axis as shown.. (The geometrical position of the brushes in an actual machine is approximately 90 electrical degrees from their position in the schematic diagram because of the shape of the end connections to the commutator.)The magnetic torque and the speed voltage appearing at the brushes are independent of the spatial waveform of the flux distribution; for convenience we shall continue to assume a sinusoidal flux-density wave in the air gap. The torque can then be found from the magnetic field viewpoint.The torque can be expressed in terms of the interaction of the direct-axis air-gapflux per pole d Φ and the space-fundamental component 1a F of the armature m.m.f.wave . With the brushes in the quadrature axis, the angle between these fields is 90 electrical degrees, and its sine equals unity. For a P pole machine 12)2(2a d F P T ϕπ=In which the minus sign has been dropped because the positive direction of thetorque can be determined from physical reasoning. The space fundamental 1a F ofthe sawtooth armature m.m.f. wave is 8/2π times its peak. Substitution in above equation then givesa d a a d a i K i m PC T ϕϕπ==2 Where a i =current in external armature circuit;a C =total number of conductors in armature winding;m =number of parallel paths through winding;Andm PC K aa π2=Is a constant fixed by the design of the winding.The rectified voltage generated in the armature has already been discussedbefore for an elementary single-coil armature. The effect of distributing the winding in several slots is shown in figure ,in which each of the rectified sine waves is the voltage generated in one of the coils, commutation taking place at the moment when the coil sides are in the neutral zone. The generated voltage as observed from the brushes is the sum of the rectified voltages of all the coils in series between brushesand is shown by the rippling line labeled a e in figure. With a dozen or socommutator segments per pole, the ripple becomes very small and the average generated voltage observed from the brushes equals the sum of the average values ofthe rectified coil voltages. The rectified voltage a e between brushes, known also asthe speed voltage, ism d a m d a a W K W m PC e ϕϕπ==2 Where a K is the design constant. The rectified voltage of a distributed winding has the same average value as that of a concentrated coil. The difference is that the ripple is greatly reduced.From the above equations, with all variable expressed in SI units:m a a Tw i e =This equation simply says that the instantaneous electric power associated with the speed voltage equals the instantaneous mechanical power associated with the magnetic torque , the direction of power flow being determined by whether the machine is acting as a motor or generator.The direct-axis air-gap flux is produced by the combined m.m.f. f f i N ∑ of the field windings, the flux-m.m.f. characteristic being the magnetization curve for the particular iron geometry of the machine. In the magnetization curve, it is assumed that the armature m.m.f. wave is perpendicular to the field axis. It will be necessary to reexamine this assumption later in this chapter, where the effects of saturation are investigated more thoroughly. Because the armature e.m.f. is proportional to flux times speed, it is usually more convenient to express the magnetization curve in termsof the armature e.m.f. 0a e at a constant speed 0m w . The voltage a e for a given fluxat any other speed m w is proportional to the speed,i.e. 00a m m a e w w e =Figure shows the magnetization curve with only one field winding excited. This curve can easily be obtained by test methods, no knowledge of any design details being required.Over a fairly wide range of excitation the reluctance of the iron is negligible compared with that of the air gap. In this region the flux is linearly proportional to the total m.m.f. of the field windings, the constant of proportionality being the direct-axis air-gap permeance.The outstanding advantages of DC machines arise from the wide variety of operating characteristics which can be obtained by selection of the method of excitation of the field windings. The field windings may be separately excited from an external DC source, or they may be self-excited; i.e., the machine may supply its own excitation. The method of excitation profoundly influences not only the steady-state characteristics, but also the dynamic behavior of the machine in control systems.The connection diagram of a separately excited generator is given. The required field current is a very small fraction of the rated armature current. A small amount of power in the field circuit may control a relatively large amount of power in the armature circuit; i.e., the generator is a power amplifier. Separately excited generators are often used in feedback control systems when control of the armature voltage over a wide range is required. The field windings of self-excited generators may be supplied in three different ways. The field may be connected in series with the armature, resulting in a shunt generator, or the field may be in two sections, one of which is connected in series and the other in shunt with the armature, resulting in a compound generator. With self-excited generators residual magnetism must be present in the machine iron to get the self-excitation process started.In the typical steady-state volt-ampere characteristics, constant-speed primemovers being assumed. The relation between the steady-state generated e.m.f. a Eand the terminal voltage t V isa a a t R I E V -=Where a I is the armature current output and a R is the armature circuitresistance. In a generator, a E is large than t V ; and the electromagnetic torque T is acountertorque opposing rotation.The terminal voltage of a separately excited generator decreases slightly with increase in the load current, principally because of the voltage drop in the armature resistance. The field current of a series generator is the same as the load current, so that the air-gap flux and hence the voltage vary widely with load. As a consequence, series generators are not often used. The voltage of shunt generators drops off somewhat with load. Compound generators are normally connected so that the m.m.f. of the series winding aids that of the shunt winding. The advantage is that through the action of the series winding the flux per pole can increase with load, resulting in a voltage output which is nearly constant. Usually, shunt winding contains many turns of comparatively heavy conductor because it must carry the full armature current of the machine. The voltage of both shunt and compound generators can be controlled over reasonable limits by means of rheostats in the shunt field. Any of the methods of excitation used for generators can also be used for motors. In the typical steady-state speed-torque characteristics, it is assumed that the motor terminals are supplied froma constant-voltage source. In a motor the relation between the e.m.f. a E generated inthe armature and the terminal voltage t V isa a a t R I E V +=Where a I is now the armature current input. The generated e.m.f. a E is nowsmaller than the terminal voltage t V , the armature current is in the oppositedirection to that in a motor, and the electromagnetic torque is in the direction to sustain rotation of the armature.In shunt and separately excited motors the field flux is nearly constant. Consequently, increased torque must be accompanied by a very nearly proportional increase in armature current and hence by a small decrease in counter e.m.f. to allow this increased current through the small armature resistance. Since counter e.m.f. is determined by flux and speed, the speed must drop slightly. Like the squirrel-cage induction motor ,the shunt motor is substantially a constant-speed motor having about 5 percent drop in speed from no load to full load. Starting torque and maximum torque are limited by the armature current that can be commutatedsuccessfully.An outstanding advantage of the shunt motor is ease of speed control. With a rheostat in the shunt-field circuit, the field current and flux per pole can be varied at will, and variation of flux causes the inverse variation of speed to maintain counter e.m.f. approximately equal to the impressed terminal voltage. A maximum speed range of about 4 or 5 to 1 can be obtained by this method, the limitation again being commutating conditions. By variation of the impressed armature voltage, very wide speed ranges can be obtained.In the series motor, increase in load is accompanied by increase in the armature current and m.m.f. and the stator field flux (provided the iron is not completely saturated). Because flux increases with load, speed must drop in order to maintain the balance between impressed voltage and counter e.m.f.; moreover, the increase in armature current caused by increased torque is smaller than in the shunt motor because of the increased flux. The series motor is therefore a varying-speed motor with a markedly drooping speed-load characteristic. For applications requiring heavy torque overloads, this characteristic is particularly advantageous because the corresponding power overloads are held to more reasonable values by the associated speed drops. Very favorable starting characteristics also result from the increase in flux with increased armature current.In the compound motor the series field may be connected either cumulatively, so that its.m.m.f.adds to that of the shunt field, or differentially, so that it opposes. The differential connection is very rarely used. A cumulatively compounded motor has speed-load characteristic intermediate between those of a shunt and a series motor, the drop of speed with load depending on the relative number of ampere-turns in the shunt and series fields. It does not have the disadvantage of very high light-load speed associated with a series motor, but it retains to a considerable degree the advantages of series excitation.The application advantages of DC machines lie in the variety of performance characteristics offered by the possibilities of shunt, series, and compound excitation. Some of these characteristics have been touched upon briefly in this article. Stillgreater possibilities exist if additional sets of brushes are added so that other voltages can be obtained from the commutator. Thus the versatility of DC machine systems and their adaptability to control, both manual and automatic, are their outstanding features.中文翻译负载运行的变压器及直流电机导论通过选择合适的匝数比，一次侧输入电压1V 可任意转换成所希望的二次侧开路电压2E 。

1、 外文原文（复印件）A: Fundamentals of Single-chip MicrocomputerT h e sin gle -ch ip mi c ro co m p u t e r is t h e cu lm in at io n of b ot h t h e d e ve lo p me nt of t h e d ig ita l co m p u t e r a n d t h e i nte g rated c ircu it a rgu ab l y t h e to w mo st s ign if i cant i nve nt i o n s of t h e 20t h c e nt u ry [1].T h ese to w t yp e s of arch ite ct u re are fo u n d in s in gle -ch ip m i cro co m p u te r. S o m e e mp l oy t h e sp l it p ro gra m /d at a m e m o r y of t h e H a r va rd arch ite ct u re , s h o wn in -5A , ot h e rs fo l lo w t h e p h i lo so p hy, wid e l y ad a p ted fo r ge n e ral -p u rp o se co m p u te rs an d m i cro p ro ce ss o rs , of m a kin g n o l o g i ca l d i st in ct i o n b et we e n p ro gra m an d d ata m e m o r y as in t h e P rin c eto n a rch ite ct u re , sh o wn in -5A.In ge n e ra l te r m s a s in g le -ch ip m ic ro co m p u t e r is ch a ra cte r ized b y t h e in co r p o rat io n of all t h e u n its of a co mp u te r into a s in gle d e vi ce , as s h o w n in F i g3-5A-3.-5A-1A Harvard type-5A. A conventional Princeton computerProgrammemory Datamemory CPU Input& Output unitmemoryCPU Input& Output unitResetInterruptsPowerFig3-5A-3. Principal features of a microcomputerRead only memory (ROM).RO M is u su a l l y fo r t h e p e r m an e nt , n o n -vo lat i le sto rage of an ap p l i cat io n s p ro g ram .M a ny m i c ro co m p u te rs a n d m i cro co nt ro l le rs are inte n d ed fo r h i gh -vo lu m e ap p l i cat io n s a n d h e n ce t h e e co n o m i cal man u fa c t u re of t h e d e vi ces re q u ires t h at t h e co nt e nts of t h e p ro gra m me mo r y b e co mm i ed p e r m a n e nt l y d u r in g t h e m a n u fa ct u re of c h ip s . C lea rl y, t h i s imp l ies a r i go ro u s ap p ro a ch to ROM co d e d e ve lo p m e nt s in ce ch an ges can n o t b e mad e af te r m an u fa ct u re .T h i s d e ve l o p m e nt p ro ces s m ay i nvo l ve e mu l at i o n u sin g a so p h ist icated d e ve lo p m e nt syste m wit h a h ard wa re e mu l at i o n capab i l it y as we ll as t h e u s e of p o we rf u l sof t war e to o l s.So m e m an u fa ct u re rs p ro vi d e ad d it i o n a l ROM o p t io n s b y in clu d in g in t h e i r ran ge d e v ic es w it h (o r inte n d ed fo r u s e wit h ) u se r p ro g ram m a b le m e mo r y. T h e s im p lest of t h e se i s u su a l l y d e v i ce wh i ch can o p e rat e in a m i cro p ro ce s so r mo d e b y u s in g s o m e of t h e in p u t /o u t p u t l in es as an ad d res s a n d d ata b u s fo r a cc es sin g exte rn a l m e m o r y. T h is t yp e o f d e vi ce can b e h ave f u n ct i o n al l y as t h e s in gle ch ip m i cro co m p u t e r f ro m wh i ch it i s d e ri ved a lb e it wit h re st r icted I/O an d a m o d if ied exte rn a l c ircu it. T h e u s e of t h e se RO M le ss d e vi ces i s co mmo n e ve n in p ro d u ct io n circu i ts wh e re t h e vo lu m e d o e s n ot ju st if y t h e d e ve lo p m e nt co sts of cu sto m o n -ch ip ROM [2];t h e re ca n st i ll b e a si gn if i cant sav in g in I/O an d o t h e r ch ip s co m pared to a External Timing components System clock Timer/ Counter Serial I/O Prarallel I/O RAM ROMCPUco nve nt io n al m i c ro p ro ces so r b ased circ u it. M o re exa ct re p l a ce m e nt fo rRO M d e v ice s can b e o b tain ed in t h e fo rm of va ria nts w it h 'p i g g y-b a c k'E P ROM(E rasab le p ro gramm ab le ROM )s o cket s o r d e v ice s w it h E P ROMin stead of ROM 。