乐彩750H写真机驱动

收稿日期：2010-09-11作者简介：王欢（1977－），女，湖北十堰人，硕士，从事机械设计、机械原理和先进制造技术等方面的研究。

普通的圆锥行星齿轮式差速器将转矩平均分配给左、右驱动车轮，这样的分配比例在汽车越野行驶或在泥泞、冰雪路上行驶，且一侧驱动车轮与地面的附着系数很小时，有陷车而不能前进的危险。

限（防）滑差速器它使大部分甚至全部扭矩传给另外一个不滑转的驱动轮，以充分利用这一驱动轮的附着力而产生足够的牵引力，大大提高了汽车在双附着系数路面上的动力性和通过性，显著改善了汽车操纵稳定性，有效提高了汽车行驶安全性［1］。

因此，防滑差速器首先在越野汽车、中型和重型汽车、多功能汽车、工程机械以及拖拉机等车辆上得到广泛应用，近年在轿车和商务车上也有采用。

限（防）滑差速器的结构形式主要有自锁式和强制锁止式。

自锁式又可分为高摩擦式、变传动比式、自由轮式3种［1］。

蜗轮蜗杆式、摩擦片式、滑块凸轮式等差速器都属于高摩擦限滑差速器。

蜗轮蜗杆式差速器是高摩擦式差速器中综合性能相当出众的一种，它可以根据各个轮对牵引力的需求而分配扭矩的输出，最为难得的是这样的分配完全靠机械装置类实现，反应迅速而准确。

doi ：10.3969/j.issn.1008-5483.2010.04.009越野汽车托森轮间差速器的效率研究王欢，孙传琼，孙国兴（湖北汽车工业学院机械工程系，湖北十堰442002）摘要：蜗轮蜗杆式托森差速器克服普通锥齿轮差速器将转矩平均分配给左、右驱动车轮而防滑能力差的缺点，有效地提高了汽车的通过性和安全性。

首先阐述了托森轮间差速器的结构组成、工作原理、转矩分配原理以及性能评价指标，然后对差速器的效率进行了分析，最后通过实例计算某越野汽车上托森差速器的效率。

关键词：托森差速器；蜗轮蜗杆式；限滑差速器；锁紧系数；转矩比；效率中国分类号：U463.218+.4文献标志码：A文章编号：1008-5483（2010）04-0035-04Research on Efficiency of Torsen Inter-wheel Differentialfor Off-road VehicleWang Huan ，Sun Chuanqiong ，Sun Guoxing（Dept.of Mechanical Engineering ，Hubei Automotive Industries Institute ，Shiyan 442002，China ）Abstract ：The structure and composition,working principle ，torque distribution principle and the performance evaluation parameters of Torsen inter-wheel differential were introduced.The efficiency of Torsen differential was analyzed ，and the efficiency of Torsen differential for an off-road vehicle was calculated.Key words ：Torsen differential ；worm gear ；limited differential ；locking coefficient ；torque ratio ；efficiency湖北汽车工业学院学报Journal of Hubei Automotive Industries Institute第24卷第4期2010年12月Vol.24No.4Dec.2010湖北汽车工业学院学报2010年12月1蜗轮蜗杆式托森轮间差速器蜗轮蜗杆式托森差速器利用蜗杆传动的不可逆性原理和齿面高摩擦条件，使差速器根据其内部差动转矩（差速器的内摩擦力矩）大小而自动锁死或松开，即在差速器内差动转矩较小时起差速作用，而过大时自动将差速器锁死，有效地提高了汽车的通过性。

ENTTEC PIXIE DRIVERD M X/U S B P I XE L L E D S T R I P D R I V E RFeatures•Drives 2 DMX universes worth of 5 Volt PIXEL LED strips•In-Built5V DC power supply with55and110 watts output power units available (pn: 73540 and73451)•In-Built 12V DC power supply with 65 and 130 watts output power units available (pn: 73542 and73453)•DMX512 Controllable and USB configurable•Supports RGB pixel strips based on WS2812 & WS2812B LEDs.•Quick 2 steps test installation: connect your pixel strips to the screw terminal output and plugmains cable to a wall outlet. It is that easy!•Stand-alone test output sequences (no external data required)•Show record and playback (Art-Net to usb using PRO-Manager App)•Power and output status LED indicators•Small, light and easy to hide design•High quality powder coated metal box•Scalable design for large projects•Up to 8 units stackable using standard 19” modular rack accessory (sold separately)•Ideal for custom shape pixel LED installations•Standard IEC mains and5Pin-XLR DMX input connectors•Plug-unplug screw terminal output connector•Automatic multi voltage mains input (110-250V AC) Safety•This unit is intended for indoor use only•Do not expose the PIXIE DRIVER to rain or moisture, doing this will void the warranty•Make all the connections before you plug in the main power•Do not remove the cover, there are no serviceable parts inside•Never plug this unit in to a dimmer pack•Always be sure to mount this unit in an area that will allow proper ventilation.Allow about6”(20cm)between this device and a wall•Power-supply cords should be routed so that they are not likely to be walked on or pinched by itemsplaced upon or against them,paying particularattention to the point they exit from the unitStart-Up Demo InstallationThe PIXIE Driver comes loaded with a scrolling rainbow demo sequence which will run and loop every time you power the unit up so you can get your installation tested straight away once you connect your LED pixel strips.When any valid data is fed through the DMX or USB ports it will override the demo playback sequence and keep listening to the data ports until you re-power the unit.If you do not want the PIXIE driver to generate any output when powered up,it can be done by erasing the pre loaded show or overwriting it with your own as further described in the ENTTEC PRO Manager software section.Power BudgetingThis section explains how many LEDs can be connected to the unit.Please note that the the55Watt model has only one power supply(VCC)and the VCC0output will not be available.The110Watt unit has two internal power supplies.(VCC and VCC0) which can not be connected in parallel. The strips supported by the PIXIE driver are based on the WS2811, WS2812 and WS2812B LEDs; the following table shows the maximum number of LEDs per power source output that the driver could handle when these are driven to their maximum power (full RGB white).Use the information in the table to define the maximum supported strips per unit and the length depending on your particular design.This table can also be used to calculate how many PIXIE drivers will suit your application when one driver is not enough.Overloading the outputs could cause the unit and the connected strips to malfunction.LED StatusThe Pixie driver comes with two LED indicators located in the front panel.The red LED indicates that the internal 5 Volts power supply is working properly and the unit is ready to operate and supply power to the strips. If the LED is OFF and you have already connected the mains cable to a working wall outlet, it means that there is a problem in the unit. In such case please contact ENTTEC support.The green LED indicates the PIXIE status and should be constantly flashing. Please refer to the following table for information about current operating status:Operation ModesThe PIXIE Driver can drive LED strips in three ways:DMX mode,Playback mode and additionally testing sequences can be sent through USB. It is only possible to use one mode at a time and the one with higher precedence will override the others. A general explanation of all the modes is made in this chapter and you can find further information on how to use and configure the settings in the ENTTEC Pro Manager software section.USB (testing sequences)The USB 2.0 port is mainly used to configure the unit and download new shows. It also allows test sequences to be run through the free application as described in the Pro Manager software section.When running the testing sequences all other modes will be overridden by the USB port as it has the highest precedence.DMX modeWhen data is fed through the DMX ports and there is no active USB sequence, this will be reflected on the strips outputs D1 and D2.By default the data coming from DMX1 connector will be sent to the beginning of the strips (section 1) through D1and D2 outputs and the data coming from DMX2 will be sent to section 2 through both outputs.The full DMX LED strip update message format is shown below assuming that an RGB strip is being used. If the DMX message has less than 512 slots other than the start code, the data for missing slots will be zero.Playback modeTrigger the stored show from the Pro Manager software or by configuring the PIXIE to start playing it on power up.The PIXIE driver comes with a pre-loaded scrolling rainbow sequence which will playback and loop forever on power up and there are more available pre recorded sequences included with the pro manager software in the Enttec website.The maximum length of the show depends on the recording parameters.E.g. The shortest possible show with 510 channels at 40frames per second, will be 25 seconds, although its length can be increased dramatically if the recording parameters are lowered or the show speed is lower.If the show has a repetitive nature you could also get it to loop-back forever.Remember that any data coming from DMX or USB ports will override the playback mode.Reference DesignPIXIE driver supports any kind of DMX output device. Here is a reference diagram of connections.PIXIE Driver USB supportThe PIXIE is supported by FTDI drivers for the following Operating Systems:•Windows XP,Windows Server2003,Windows Vista, Windows Server 2008,Windows 7, Windows 8, Windows Server 2008R2. (32 bit and 64 bit versions)•Mac OS X (Mac OS X 10.6 or later )•Linux/BSDPRO-MANAGERENTTEC provides a free cross-platform (Windows & Mac only) application to configure, test and update the PIXIE. It also allows the user to record a Artnet show into the memory and set-up the standalone mode. The application is available for Windows or Mac from the ENTTEC website.•Use this application to test,troubleshoot and update the PIXIE,record,playback,set-upstandalone shows, send Art-Net and predefinedoutput pixel patterns to your strips.•This application is merely a testing tool and not Lighting Control software.This manual will cover the Windows7™installation process, by way of example. Others will be similar, but the particulars of how each operating system works in terms of screen shots have been omitted for brevity.Before plugging in your PIXIE to your computer, please install the driver, by installing the PRO Manager software available from Enttec website. Select “YES” when you are asked to install FTDI drivers and follow the installation wizard.Once the driver has finished installing, you may now power up the PIXIE and plug in the micro USB cable to connect the device to your computer. One end, the micro USB (smaller connector) plug, will fit the USB port in the unit. The other end, which is wider and almost flat in comparison, goes to any available USB port in your computer or you may also plug it into a USB hub.When you make the connection to your computer,a message should appear(usually a few seconds later in Windows) saying your computer has detected new hardware. It will be correctly identified as ENTTEC PIXIE Driver by your computer.“Devices” TabFrom the PRO Manager Home page, you can click the “Find Devices” button to search for Enttec devices connected to your computer. Once it finds it, please select the PIXIE from the selection box to start communication.Once selected, you will see all the device information on the Home Page,from here you can configure Settings and update the firmware on the PIXIE.Firmware UpdateUse the latest firmware file meant for PIXIE driver available on the ENTTEC website and upload it using the upload button (“Choose File” - as per Chrome browser).After selecting the correct file, click on the Update Firmware button and let the update proceed.Once Finished, the page will automatically refresh, and device information will be updated to reflect the updated firmware.Pixie SettingsAvailable on firmware 1.5 & onwards, settings can now be changed from the Home page itself.DMX PersonalityAllows the DMX route to be changed.Personality1: Both outputs (D1 & D2) are mapped toboth DMX inputs (DMX1 drives section1 and DMX2drives section2)Personality2: DMX1 is mapped to D1 only, and DMX2 ismapped to D2 only.Additional setting for Personality2, allows the physical LED pixels to be grouped onto desired number of DMX pixels. (patching more than 1 LED pixel to a group of DMX channels – RGB inclusive)How these personalities can be used is discussed further under “Application Usage ”LED Strip protocolAllows compatibility amongst the supported protocols (WS2811, WS2812, WS2812b). Please check your strip to see which protocol it supports.Run show on DMX lossIf standalone show is programmed onto Pixie, and this option is set to Yes and, if no DMX input is received, the show will be played back. (3 seconds timeout for DMX input)Pixel RGB MappingAllows the default order of RGB mapping to be changed on the Pixie, usually to conform with non-standard mapping.This setting applies to all RGB data sources: DMX, USB, and show replay.The default RGB mapping assumes that both the DMX input and the led strip outputs are in RGB order.For example, if the led-strips have GRB ordering, you can change this option to GRB here, and Pixie will map the colours correctly. This avoids having to change the DMX source RGB order to conform to the strip.“SEND” TabIt is possible to send pre-defined testing sequences,personalised data or Art-Net packets coming from any external source to your strips using the tools provided in this window.Select one out of the three available sources: “Test Patterns”,“Live Artnet” or “From Faders”. Then select the Output configuration depending on your particular wiring need.The Test Patterns mode will start sending predefined sequences to your strips once you select the desired one from the drop down.The Live Art-Net section will allow the user to send any incoming valid Art-Net data straight to the pixel strips whilstthe pro manager is running and a USB cable is connected.Please select the matching start universe and make sure the Art-net data is being sent to your computer IP address or broadcasted.PRO-Manager will show the mapping from universe to sections on each output, based on your selections. Closing or changing the Send window, will stop Art-Net to Pixie send, PRO-Manager only sends to Pixie while on this page.Finally, data can be sent to any particular pixel by using the channel faders which allow you to adjust the intensity of any desired LED on the strip.“Standalone” TabStandalone mode allows you to record (and playback)shows via Art-Net input to PIXIE memory. The duration of the recording depends on the configuration selected before recording. The recorder is smart enough to only record changes in the frames, so as to accommodate as many frames as possible.The recording trigger feature will let you select a channel in your show to start/stop the recording when it is greaterthan a selected value. Once the configuration is all set, you can click on “Record Art-Net” button to start recording the show.The recording is saved to a file, and is only transferred to the memory when recording is stopped by using the “Stop Recording” button or driving the trigger channel to the right value. Whilst recording, live data is sent to the strips, so you can decide when to stop.The recording can now be transferred to memory using “Write to Memory” button and the upload to memory progress is shown as it happens.Once the show is uploaded to memory successfully, the page is automatically refreshed to allow show control on the recorded show.The show can now be played and stopped using the controls on this page. These controls will only be available, if there is a show stored in memory.You can also export and import recorded shows using the “Export Show to File” or “Import Show to PIXIE Driver”buttons.Application Usage ExamplesDepending on usage, Pixie Driver can be setup to be used in different ways. Following are some examples that will highlight these:Drive 300 leds from one DMX UniverseStrip used: 8PL-60-F (5M of Smart Pixel Tape)Pixie is setup to use DMX Personality2, with pixel grouping set to 2.This setup allows you to map 450 channels of DMX to 300 LEDs (each RGB DMX address is mapped to 2 pixel LEDs) You can even use less DMX channels (with a higher pixel grouping) to drive the entire 300 LEDs.Pixie 55W driver will only support DMX1 in this scenario, however Pixie 110W driver can be used to drive 300 LEDs each from both DMX1 & DMX2Fig: Drive 300 leds from one DMX Universe (110W) Drive 300 leds from DMX1 & DMX2 (combined) Strip used: 8PL-60-F (5M of Smart Pixel Tape)Pixie is setup to use DMX Personality1This setup allows you to map DMX1 to the first section (170 leds) and DMX2 to the second section (remaining 130 leds) – allowing upto 300 leds in totalFig: Drive 300 leds from DMX1 & DMX2 (combined)Physical DimensionsThe unit is designed to fit the modular rack accessory (sold separately) which allows stacking up to 8 units in a standard 19” rack using 3 standard rack mount units (3RU). Stackable Modular Rack (Accessory)The modular rack (sold separately) allows up to 8 Pixie units to be stacked up using only 3 standard rack units (3RU). Also has an in-built fan at the rear side.SpecificationsDue to continuous improvements and innovations of all ENTTEC products, specifications and features are subject to change without notice.Ordering InformationThe PIXIE DRIVER and compatible products can be ordered from our website or through your ENTTEC dealer using the following part numbers. Different voltage and protocol units are made under special order (please contact us). ENTTEC PTY LTD ENTTEC AMERICAS17/5 Samantha Court 604A Cornerstone Ct. Knoxfield Victoria 3180Hillsborough NC27278 Australia USATel: +61 3 9763 5755 Tel-Fax: (888) 454-5922 Fax: +61 3 9763 5688 email ****************。

针对所有国产4色机一：如何初始化设置菜单→使用者设置菜单→初始设定值二：初始化后英文变中文右4（按3下）→右2→右1→左4（一直按到出现中文）→确定三：更改PASS值设置菜单→打印模式菜单→每行喷印次数→一般改为“四次”或“六次”→确定四：更改托架速度设置菜单→打印模式菜单→托架速度→一般改为“7”→确定五：页边留白设置菜单→纸张选项菜单→页边留白→“正常”改为“扩展”→确定六：计量单位设置菜单→使用者设置菜单→计量单位选择→“英制”改为“公制”→确定七：保存设置菜单→使用者设置菜单→保存使用者设置→保存到“1”里→确定写真机的常见问题及解决办法1．错位：A．故障现象：左右错位大于0.5公分，隔段错位。

电机阻力值过大。

可检查皮带，皮带轮，铜套，滑面贴，光栅，确保都没有问题仍不能解决，更换电机。

B．故障现象：左右错位小于0.5公分，连续错位。

铜套阻力过大，可清洗铜套，擦拭光杆或降低托架速度。

仍不能解决，更换铜套C．故障现象：出图斜，成平行四边形。

擦光栅，译码器。

仍不能解决，检查光栅如果受损，更换光栅。

D．故障现象：字体周围有杂色虚边。

校准喷头。

2．出图速度慢：A.故障现象：打图左右有停顿。

操作系统是否WIN98，外部并行打印口是否是ECP3．喷头不出墨：A．故障现象：单个喷头不出墨。

交叉换位打清洗后，判断触点带是否有问题。

如无，可以判断是烧或者堵，堵的话可用热的纯净水冲泡。

如固定一个颜色经常堵头，可与墨水供应商联系，调换墨水。

B．故障现象：所有喷头均不出喷墨，其中有一个喷头有问题，影响其他。

逐个打清洗挑出来即可，或者墨车板有问题。

4.打印出的图像歪斜错位或者走弧线？A.光栅太脏:用棉签蘸酒精擦拭光栅并保持环境卫生或更换光栅B.光栅感应器太脏:拆除光栅感应器用酒精擦拭或更换光栅感应器C.铜环磨损厉害或太脏:更换铜环或涂抹无尘机油保持润滑D.小车运行速度太快:将小车速度调到“7”或“8”为宜5.打印时小车两边停顿运行不流畅导致打印速度变慢?A.电脑未设置好ECP打印端:电脑重启，在电脑进行硬件自检时按DEL键进入COMS设置，进入INTEGRATED PERIPHERALS功能选项，将其中的Parallel Port Mode设置为ECP（注意：一定要是标准ECP，而不是EPP，SPP 或ECP/EPP），最后保存并退出BIOS,随后，电脑会重新启动，windows系统自动检测到ECP打印口并为其安装驱动程序，这时，您就可以使用ECP打印口所提供的告诉传输性能了。

一、安装软件1、安装前准备2、找安装包3、软件参数设置二、软件连接机器三、软件介绍四、软件报错信息和解决方案一、软件安装1.安装前准备a、安装前卸载已经安装的软件并且删除安好的文件夹B、推荐电脑硬件和软件配置：硬件：系统：win7、winXPCPU：2.50GHZ内存：2.00GB主板：P321-ES3G2、找到安装包--PrintExp_16H4C_C图1 图2双击安装软件，安装过程中需要更改或者选择的地方如下图，其它地方无需调整，选择下一步或者确定即可图3图4图53、软件参数设置找到下图，双击打开软件，图6图7新装软件共需要调整4点①修改清洗参数②修改运动参数（横向、纵向马达校准）③墨序设置④偏差校正（双向、步进校准）具体修改内容及方法①修改清洗参数图8如上图输入密码进入后，按照下图的内容输入，然后点击应用确定，图9确定后弹出下图，再次点击应用，确定②修改运动参数图10a.横向马达校准第一步红圈1内输入800，然后点移动，等小车停下后点红圈3内的复位，小车回到正确位置后,第二步在红圈内1内输入3500（1.9米机器输入2400），然后点移动，等小车停下后点红圈3内的复位，小车回到正确位置后，第三步再次在红圈内1内输入3500（1.9米机器输入2400），然后点移动，等小车停下后点红圈3内的复位，小车回到正确位置，第四步检查设置，红圈2内的齿轮比数值在4.7左右，大于5小于4说明横向马达校准失败b.纵向马达校准第一步直接在红圈5内走布长度后面输入2500，然后点红圈6内的计算1次，然后点应用第二步在机器打印平台上找任意一点A，在这点A对应的纸上找一点B，然后在红圈4内输入1000，点移动，等纸停下以后在平台A点对应的纸上标记C点，标记好后用卷尺测量BC两点之间的距离，将测量的距离换算成毫米，把数值输入到走布长度里点击1次计算第三步检查参数，红圈7内1脉冲=300到400之间的某额数值，如大于400小于300则说明步进没设置好③墨序设置设置好后点应用、确定图11 ④偏差校正图12图13a.双向校准红圈1内只选择360精度，红圈2内选择低速打印、中速打印、高速打印，红圈三内输入打印出来对应的数值。

注：1、机器更改设置完毕，如不保存设定数值机器重新开机后将恢复原来设置！ 2、打印黑色字符时如有颜色阴影应重新设置颜色静曲和颜色校准，先设置颜色静曲后设置颜色校准！ 3、机器开机之前确保接好地线，电脑及机器开机状态下且勿拔插数据线！ 4、为保证打印质量每天开机先进行颜色测试，然后进行喷头清洗！ 5、定期用卫生棉沾缝纫机油擦拭轨道；用棉棒沾纯净水擦拭光栅；抽完喷头后,一定要保证喷头和触点带电路干燥！蒙泰软件设置：1、在电脑COMS中设置ECP端口。

重启电脑按DEL进入INTEGRATED PERIPHERALS功能选项，将其中的PARALLEL PORT MODE设置为ECP，F10保存退出。

2、蒙泰中添加“ENCAD Novajet”-------“Novajet750”，（选择850机器时，打印机设定里面将纸张类型设置为高光相纸，墨水设置为CMYK （right））。

3、打开蒙泰：按“打印”（第五个图标）打印机设定打印端口选“FITE”或“LPT1”。

oki彩色打印机驱动安装说明（OKI color printer driverinstallation instructions）readme.txt= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =oki c810dn软件cd - rome版本 1.00copyright (c) 2008 oki data corporation= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =目录1. 关于本cd - rome2. cd rom的构成3. windows环境3.1 在windows 2000上安装3.1.1 使用安装程序3.1.2 通过添加打印机向导安装3.1.3 即插即用安装3.1.3.1 通过usb接口连接3.2 在windows xp / server 2003上安装3.2.1 使用安装程序3.2.2 通过安装打印机安装3.2.3 即插即用安装3.2.3.1 通过usb接口连接3.3 在windows vista / server 2008上安装3.3.1 使用安装程序3.3.2 即插即用安装3.3.2.1 通过usb接口连接4. macintosh环境4.1 在macintosh上安装※关于商标= = = = = = = = = = = = = = = = = = = = = = = = = = = = =1. 关于本cd - rome= = = = = = = = = = = = = = = = = = = = = = = = = = = = =本cd - rom包含oki c810dn专用的软件.打印机驱动程序为windows 2000 / xp / server 2003 / vista / server 2008、macintosh、mac osx专用.有关相应机型的详细信息, 请参阅打印机软件的用户手册及各目录中的 "gas" 或 "readme".= = = = = = = = = = = = = = = = = = = = = = = = = = = = =2. cd rom的构成= = = = = = = = = = = = = = = = = = = = = = = = = = = = =本cd - rom的构成如下.windowsdrivers windows专用打印机驱动程序.utilities 包括颜色和网络设定等各种实用程序.misc 包括adobe reader等.cdinst 供安装程序使用的目标文件.i'm 供安装程序使用的目标文件.(注意)- 以下各种软件均是使用 "安装程序 (cd 根目录的startup.exe) 安装.nic setup utilityoki lpr utilitynetwork extensioncolor swatch utilitycolor correct utilityoki setup utilitymacintoshdriver 包括macintosh专用打印机描述文件、mac os x专用打印机描述文件.utility 包括adobe reader及网络设定专用的各种实用程序. other language包括英文版专用打印机驱动程序.= = = = = = = = = = = = = = = = = = = = = = = = = = = = =3. windows环境= = = = = = = = = = = = = = = = = = = = = = = = = = = = =---------------------------------3.1 在windows 2000上安装---------------------------------(注意) 需要administrator权限.- 在本文中cd - rom驱动器名以d: 为例.- 通过 "软件cd rome" 安装时, 请原封不动使用该文件夹名.- 将 "软件cd rome" 复制到硬盘等进行安装时, 请将 "d: \" 替换为复制有打印机驱动程序的文件夹的路径.- 当即插即用程序不能搜索出该新硬件时,请参阅 "3.1.1 使用安装程序".-----------------------------------------3.1.1 使用安装程序-----------------------------------------(1) insert "software CD-ROM"".(2) select "run" from the "start" menu, and "open" columnType "D:\Setup" and click "OK"".(3) read the software license agreement carefully and click the accept button.(4) click Install driver.(5) choose to use it as a local printer or as a network printer,Click the "next" button.(6) install according to the prompt of the screen.For more information, please refer to the user manual (installation section).(7) when used as a network printer, the printer icon added will be displayed in the "printers and faxes" folder after installation. When connected to the USB interface and used as a local printer, it will automatically install the driver after it is connected to the computer. Finished installationAfter it is finished, it will be displayed in the printers and faxes folder.-----------------------------------------3.1.2 installs by adding a printer wizard-----------------------------------------(1) insert "software CD-ROM"".(2) from the "start" menu, select "Settings" - "printers and faxes", double-click "add printers"".(3) click "Add Printer Wizard", and then click next".(4) select "local printer" and click "next"".(5) select "use the following port", select port, click "next"".(6) click "use disk"".(7) when the "disk install" screen prompt appears in the "vendor file replication source",Type "D:\Drivers\CHS\WinXP2k\Hiper-C""Click ok".(8) select the name of the printer you want to install, and clicknext".(9) confirm the name of the printer and choose "yes" in "whether you want to set the printer as the default printer", and click "next"".(10) select "do not share this printer", and click "next"".(11) when showing "want to print the test page?"" Choose "no" and click "next"".(12) Click finish".(13) when you show "no digital signature" is found, click "yes"". Start copying files.(14) after installation, the printer icon added will be displayed in the "printers and faxes" folder.---------------------------------------------3.1.3 plug and play installation---------------------------------------------------------------------------------------------Connection of 3.1.3.1USB port------------------------------------------------(1) make sure that the printer and the computer's power are closed.(2) connect the USB cable.(3) open the printer power supply.(4) start Windows.Reboot if Windows is already started. If it is connected to the new USB corresponding printer,Windows will automatically install USB printing support.(5) when you display the search for the new hardware wizard, click next".When you show "no digital signature" is found, click Yes, and go to step (11).(6) choose "search for drivers for my device" (recommended), click "next"".(7) select the specified path, and click next".(8) insert "software CD-ROM"". At the source of the manufacturer file replication,Type "D:\Drivers\CHS\WinXP2k\Hiper-C""Click ok".(9) after confirming the driver of the device, click next".(10) if the "no signature" dialog box pops up, then click "yes"". Start copying files.(11) in the "new hardware has been searched" dialog box,Click finish".(12) make sure that the printer icon has been added.-------------------------------------------3.2 install on Windows XP/Server 2003-------------------------------------------(notice) you must have Administrator permissions.In this paper, the CD-ROM driver name, D:, is taken as an example.Install through the software CD-ROM, please use the folder name directly.If you copy the software CD-ROM to the hard disk and so on, when you install it, please send it"D:\" replaces the path to the folder where the printer driver is copied.When the plug and play device cannot search for new hardware,Please refer to "3.2.1 use installer"".-----------------------------------------3.2.1 using installer-----------------------------------------(notice)In the case of connecting to the USB interface, if you install the installer, start the printer andWhen WindowsXP/Server 2003, the screen displays "search for new hardware"".Plug and play must be used when installing on WindowsXP/Server 2003 for the first time.(1) insert "software CD-ROM"".(2) select "run" from the "start" menu, and then "open" columnType "D:\Startup" and click "OK"".(3) read the software license agreement carefully and click the accept button.(4) click Install driver.(5) install according to the prompt of the screen.For more information, please refer to the user manual (installation section).(6) after installation, the printer icon added will be displayed in the "printers and faxes" folder.,3.2.2 is installed by adding printers,(1) insert "software CD-ROM"".(2) open the "control panel" from the "start" menu and double-click "printers and faxes"".Click "Install Printer"".(3) the screen prompts "Add Printer Wizard", and click "next"".(4) select the local printer that connects to this computer, and click next".(5) select "use the following ports", select the port, and click "next"".(6) click "use disk"".(7) when the "disk installation" is displayed, at the "vendor file replication source",(in the case of 32bit OS)Type "D:\Drivers\CHS\WinXP2k\Hiper-C""(64bit OS)Type "D:\Drivers\CHS\WinXP64\Hiper-C""Click ok".(8) select the folder to install, and click next".(9) confirm the name of the printer and choose "yes" in "whether you want to set the printer as the default printer", and click "next"".(10) select "do not share this printer", and click "next"".(11) when showing "want to print the test page?"" Choose "no" and click "next"".(12) Click finish".(13) when you display "installing from hardware", click "continue"". Start copying files.(14) after installation, the printer icon added is displayed in the "printers and faxes" folder.---------------------------------------------3.2.3 plug and play installation---------------------------------------------------------------------------------------------Connection of 3.2.3.1USB port------------------------------------------------(1) make sure that the printer and the computer's power are closed.(2) connect the USB cable.(3) open the printer power supply.(4) start Windows.Reboot if Windows is already started.If it is connected to the new USB corresponding printer, Windows will automatically install USB printing support.(5) after the screen display "start searching for new hardware wizard", if the pop-up "to search software, want to connectWindows Update" dialog box?,Please choose "no, no connection", and then choose "the next step"".Please select "browse or install from specific path" (detail), and click "next"".Sometimes need to display a dialog box with a 1-2 minutes.If the screen does not display the above content, go to "3.2.2" using the installer".(6) insert printer software CD-ROM".(7) choose the most appropriate driver to search from the following path".(8) do not choose "search disk" (floppy disk, CD-ROM, etc.)".Select "include the following path",(in the case of 32bit OS)Type "D:\Drivers\CHS\WinXP2k\Hiper-C""(in the case of 64bit OS)Type "D:\Drivers\CHS\WinXP64\Hiper-C""Click next".(9) when you display the tooltip for installing hardware, click continue".(10) when displaying "insert disk", go to step (12).Start copying files.(11) make sure that the new hardware has been searched, and click finish".Go to step (15).Employed(12) insert the "software CD-ROM" when the screen shows "insert disk"",Click ok".(13) at the source of the manufacturer's document replication,(in the case of 32bit OS)Type "D:\Drivers\CHS\WinXP2k\Hiper-C""(in the case of 64bit OS)Type "D:\Drivers\CHS\WinXP64\Hiper-C""Click next". Start copying files.(14) make sure that the new hardware has been searched, and click finish".Employed(15) select "start" - "control panel", click "printers" and other hardware",Confirm the printer icon has been added.-----------------------------------------3.3 install on Windows Vista/Server 2008-----------------------------------------(notice) you must have Administrator permissions.In this paper, the CD-ROM driver name, D:, is taken as an example.Install through the software CD-ROM, please use the folder name directly.If you copy the software CD-ROM to the hard disk and so on, when you install it, replace the D:\Copy the path to the folder with printer driver.When the plug and play program is unable to search for the newhardware, please refer to "3.3.1 using the installer"".-----------------------------------------3.3.1 using installer-----------------------------------------(1) insert "software CD-ROM"".(2) from the "start" menu, select "D:\Startup" in "run"",Click "startup" on "open"".(3) read the software license agreement carefully and click accept".(4) click "install driver"".(5) install according to the prompt of the screen.For more information, please refer to the user manual (installation section).(6) after installation, the printer icon added will be displayed in the "printers and faxes" folder.---------------------------------------------3.3.2 plug and play installation---------------------------------------------------------------------------------------------3.3.2.1设施上通过USB端口连接------------------------------------------------（1）确认打印机和电脑的电源均为关闭状态。

1 一、界面说明主菜单1、装载打印载体重新上纸后测纸2、切割无用3、暂停当打印过程中喷头断线或其他问题时按此键暂停打印4、重新设置当机器工作中想终止工作时清除打印信息5、馈送载体菜单进、退纸6、设置菜单说明一般情况下3、5、6项不能随便更改建议保持默认值6.1、打印模式菜单2切割1装载打印载体3暂停4重新设置7辅助功能菜单6设置菜单5馈送载体菜单2纸张选项菜单1打印模式菜单3HP-GL型/2菜单7退出6串口通讯菜单5墨水选项菜单4使用者设定菜单优质模式彩色模式每英寸点数退出打印方向托架速度每行喷印次数2 彩色模式彩色优质模式使用者自定每英寸点数建议600 每行喷印次数四或六次托架速度7或8 打印方向双向 6.2、纸张选项菜单打印载体类型卷轴打印载体标准全部页边留白扩展自动装载延迟6 自动切割关节省打印载体开自动擦墨默认 6.3 勿动6.4、使用者设定菜单选择使用者设定使用者选定的菜单设置保存在18中任意一项保存使用者设定所需项选定后必须保存在“使用者设定”中的一项中保存使用者设定选择使用者设定计量单位选择语种退出液晶显示对比度打印设定值初始设定值打印载体标准打印载体类型页边留白自动装载延迟退出自动擦墨节省打印载体自动切割 3 计量单位选择公制语种中文初始设定值勿动打印设定值勿动液晶显示对比度6 7、辅助功能菜单清洗清洗喷头、查看喷头状况存取墨水匣打印过程中对喷头进行抽墨等操作颜色校准菜单校准喷头校准菜单存取墨水匣清洗颜色校准菜单校准菜单退出服务菜单打印设定值显示设定品红色垂直校准青色垂直校准黄色垂直校准校准打印测试退出黄色水平校准品红色水平校准青色水平校准图纸纵轴线测试使用坐标校准颜色静区菜单退出图纸纵轴线打开喷嘴菜单4 服务菜单校准菜单诊断菜单诊断菜单校准菜单退出测试打印墨水匣信息关于慢静区测试静区测试单线测试退出慢静区伺服循环测试伺服PWM测试附件菜单退出连续测试颜色测试托架测试 5 二、操作步骤1、上纸将纸茼从托纸杆一头穿过两边卡纸盘按紧。

乐彩750等热发泡写真机故障处理与耗材认知热发泡写真机比较有名的是乐彩750、5500、5800、6416、6640等，但是与压电机相比，这类机器速度慢，精度差，现在均已经停止生产，但是还有很多朋友在用这类机器。

为了方便各位处理问题，乐彩技术员们整理出一些处理的技巧，欢迎各位学习。

1 750灰也就是750—H 采用通用型208喷头采用热发泡系类墨水 300dpi750常见问题：液晶屏显示“Carriage Axis Failure故障原因：1、皮带轮与铜套的损坏造成阻力过大；2、一般电机的寿命为800-1200小时，使用时间超出此范围可能引起电机的损坏；解决方法：检查皮带轮轴承的转动是否正常，如出现轴承变形或转动不顺畅，说明皮带轮损坏；2、拆卸铜套，进行清洁擦拭然后再重试；3、首先进行“伺服循环”测试，如果阻力数值不断增加或噪音过大，说明电机使用时间过长，需要换新的电机；液晶屏显示“Bad Carriage Paper Sensor”故障原因：1、测纸器排线与喷墨板的连接端口松动；2、内部线路短路造成测纸器的损坏；解决方法：1、关掉电源，用酒精擦拭测纸器排线后重新启动；2、更换测纸感应器；液晶屏显示“Servioeboj:Preallocmemout”故障原因：打印文件过大造成内存不足；解决方法：更换内存或扩展内存大小；机器在启动时，墨车左右乱跳故障原因：1、数据线未连接好；2、光栅检测器未连接好；3、伺服电机烧坏、主板L6203芯片烧坏；解决方法：1、重新插拔数据线或换数据线；2、重新插拔光栅检测线；3、换伺服电机后再换主板；写真机启动墨车移动到左端报错故障原因：1、写真机测纸器损坏；2、写真机小车板与测纸器未连接好；解决方法：1、换测纸器；2、将测纸器的线和小车板的接口对齐再插紧；草图模式2Pass 8平方生产模式3Pass 6平方一般品质模式4Pass 4平方高品质模式 6Pass 3平方2 750白采用通用型208喷头采用热发泡系类墨水 300dpi3 5500 采用416喷头采用416系类墨水 1200dpi416系列常见问题：机器不联机故障原因：1 一般都是电脑系统的问题2 主板和USB线解决方法：1 换台电脑或重新做系统2 更换主板或USB线托架过流故障原因：1 电机老化了2 小车架断裂决方法：1更换电机2 更换小车架打图乱码故障原因：1 电脑数据发送慢2 喷头干扰3光栅或光栅解码器脏了解决方法：1 换电脑或者先把作业打印到文件夹2 检查一下喷头看看那个喷头产生干扰就换了那个喷头3 擦拭光栅或换光栅解码器草图模式2Pass 12平方生产模式3Pass 10平方一般品质模式4Pass 8平方高品质模式 6Pass 6.8平方4 5800 采用416喷头采用416系类墨水 1200dpi5 6416A 采用416喷头采用416系类墨水 1200dpi6 6416C 采用416喷头采用416系类墨水 1200dpi7 6208 采用208加密喷头采用热发泡系类墨水 1200dpi 6208的问题跟416系列问题一样8 6640 采用640喷头采用热发泡系类墨水 1200dpi6640机型常见问题：托架轴故障故障原因：1 数据线没插好2 电机3 小车架阻力大解决方法：1 重新插拔数据线2 电机老化了更换电机3 用缝纫机油擦拭光轴或更换铜套墨水夹故障故障原因：1 喷头墨水过高2 喷头墨水太多或少解决方法：1 更换喷头2 添加或减少墨水测不到纸张故障原因：1 机体有地方露白2 测纸器坏了解决方法：1 用黑色的油笔涂抹露白的地方2 更换测纸器草图模式2Pass 22平方生产模式3Pass 17平方一般品质模式4Pass 12.8平方高品质模式 6Pass 7平方640、416、208的区别416喷头208喷头640喷头640、416和208的区别在于芯片以上图片可以对比一下208喷头的加密区别208不加密 208加密208不加密 208加密208不加密就是看喷头上面有没有写208，加密喷头上面写的有208 ，还有就是从喷头盒上区分 208（银/silver）是不加密的 208PIus是加密的以上图片大家可以区分发泡机墨水的区分下面的图片(左图）是热发泡系列墨水（右图）是416系列墨水热发泡系列的墨水适用机型： 750灰、750白、6208、6640这几款机型416系列的墨水适用机型： 5500、5800、6416A、6416C这几款机型图1大家可以仔细看下图1上面写的“热发泡系列”这几个字这就是热发泡系列的墨水图2上面写的“416系列”这就是416系列的墨水图2这个是208不加密的这个是208加密的这个是416喷头他没有加密和不加密一说以上就是让大家认识的发泡机型和对喷头墨水的认识。

幻影机器驱动及蒙泰安装方法一、找到幻影驱动程序（有幻影驱动光盘），在安装之前要把机器电源关掉或把USB传输线断开，在开机情况下是不能安装驱动的1、点击USB2.0文件夹，双击setup2、选择I accept the terms in the license agreement,然后点Next3、点Install开始安装4、点确认安装完成，重启电脑二、把USB线跟机器连接好，把机器按正常顺序打开，1、电脑上显示找到新硬件，然后点下一步进行安装，自动搜索就可以了，一共有两次都是同样的方法进行安装。

到这里驱动都安装完了。

下面进行蒙泰安装三、把蒙泰光盘放入光驱：电脑会自动弹出安装程序窗口1、注：如果不从光盘直接从硬盘安装，则点击文件夹中的setup或者INSTALL文件夹下的INSTALL文件进行安装，所以安装蒙泰有三个地方都可以进行。

2、点击第一个进行安装3、默认为C盘，可以改为其他磁盘4、稍后重起，关掉弹出的页面。

5、点开始----程序-----把蒙泰及蒙泰打印管理系统图标发送一个快捷方式到桌面6、把蒙泰加密狗插入电脑7、首先打开蒙泰打印机管理系统，这时会弹出一个对话窗，一定要输入端口名称，任何名字都可以，且记要输入，如果不输入名称后来是不能联机打图，输入后确认后就可以，如果在右上角没有端口显示出来则在管理-----设定端口----设定系统打印端口----添加端口----COM1---确认----关闭8、打开蒙泰进行设置如果打开蒙泰出现上面提示则是加密狗没有插好或损坏，请重新换个USB口或更换加密狗9、点文件---打印机设定---安装蒙泰打印机这时要注意：160或DYE是水性机驱动，ECO是油性（户外机）驱动，选择好后点击确认10、点设为默认打印机11、点设定打印机，一定要注意把打印端口改为之前在蒙泰打印管理系统设置好的端口名称，且记，设置好后确认12、点文件---建立新文件-----设置好纸张及留空---确认13、如果打印颜色深或太浓，请把浓淡控制减淡。

乐彩easyjet1601操作手册（原创版）目录1.乐彩 easyjet1601 操作手册概述2.安装与设置3.基本操作4.进阶操作5.维护与保养6.故障排除正文一、乐彩 easyjet1601 操作手册概述乐彩 easyjet1601 是一款性能卓越的喷墨打印机，具备高速打印、高质量打印和便捷的网络连接功能。

为了让用户更好地掌握该产品的使用方法，特制定本操作手册，详细介绍了安装、设置、操作、维护保养以及故障排除等方面的内容。

二、安装与设置1.拆包装：在确保产品安全的前提下，打开包装箱，将打印机和附件逐一取出。

2.安装墨盒：根据产品提示，将墨盒安装到相应的墨盒槽。

3.连接电源：将电源线一端连接到打印机，另一端插入电源插座。

4.连接电脑：通过 USB 线缆或者网络连接，将打印机与电脑连接。

5.安装驱动：在电脑上安装乐彩 easyjet1601 的驱动程序。

6.设置默认打印机：在电脑的控制面板中，将乐彩 easyjet1601 设置为默认打印机。

三、基本操作1.打印文件：在电脑上打开需要打印的文件，点击“打印”按钮，选择乐彩 easyjet1601 作为打印机，确认打印任务。

2.照片打印：使用附带的照片打印软件，选择照片并设置好打印参数，点击“打印”按钮。

3.纸张设置：根据打印需求，在打印机控制面板上选择合适的纸张类型和纸张大小。

四、进阶操作1.颜色调整：在打印机控制面板上，可以对打印出的颜色进行调整，以达到最佳的打印效果。

2.纸张类型设置：可以根据不同的打印需求，在打印机控制面板上设置纸张类型。

3.故障诊断：在打印机出现故障时，可以通过打印机控制面板上的故障诊断功能，判断故障原因。

五、维护与保养1.定期清洁：使用湿布擦拭打印机外部，避免使用腐蚀性液体。

2.墨盒更换：当墨盒用尽时，需要及时更换新的墨盒。

3.故障处理：如遇到故障，请参照本手册的故障排除章节进行处理。

六、故障排除1.打印不出纸：检查纸张是否装载正确，纸张类型是否设置正确。

乐彩750写真机操作维修指南乐彩750写真机操作维修指南750写真机常见故障及解决办法：以下是乐彩写真机 750H，天彩写真机，等国产进口750写真机故障的解析和维修下面以天彩750写真机为例：一、打图时出现方格断墨写真机光栅赃了，需用棉签沾清水擦洗上下光栅，应多擦几次洗净后用干棉签把水擦干。

二、写真机不可认墨水匣写真机解密卡松了需重新插好，或解密卡坏了。

三、打图错位1、皮带擦皮带轮卡，需调整皮带轮。

2、伺服电机坏了，需更换伺服电机。

3、铜环脏了，需清洗或更换铜环。

四、写真机喷头不出墨1、小车板发热，需关闭机器休整。

2、触电带坏了，需更换触电带。

3、喷头堵了，需抽洗喷头。

⒋墨管接口堵了，需拔下多插几次即可，⒌喷头干扰，互换喷头位置，和用纸巾垫在喷头与触电带之间来检查是那个喷头干扰，更换喷头。

⒍如出现四个喷头同时不出墨，在排除喷头干扰后还不出墨即为小车板坏了。

五、写真机测不到纸1、测纸器脏了，需用棉签沾清水擦洗。

2、测纸器没装好，需重装。

3、测纸器坏了，需更换测纸器。

4、小车板坏了，需更换。

六、写真机打图边线向一边斜1、伺服电机坏了，需更换伺服电机。

2、光栅感应器脏了，需用棉签沾清水擦洗。

光栅感应器坏了，需更换。

七、开机时小车架撞左边机架1、光栅感应器脏了，需清洗干净。

2、光栅感应器坏了，需更换。

3、数据线没插好，需多插几次。

八、写真机频繁测纸1、进纸传感器脏了，需清洗。

2、进纸传感器没插好与主板连接或接触不好。

3、进纸传感器坏了，需更换。

九、写真机打图时喷头滴墨1、喷头内空气没抽净，需多抽几次。

2、墨管接口吻合不好，需重新插好或更换接口。

3、喷头漏气，需查出何处漏气然后用胶水密封。

十、写真机打图时图面模糊静电干扰，（静电安全电压为三伏以内）十一、写真机打图时出现规则性断墨1、小车板不稳定。

2、喷头位置不对。

十二、常见英文报错1、Internal ERROR shutdown Bad carriage paper sensor(小车板或测纸器没插好接触不良)2、Internal ERROR shutdown Carriage Axis Failure(电机接触不良需重插或电机损坏)3、Internal ERROR shutdown CB LOLT 01RANGE LL:0(测纸器接触不好，需重插或更换测纸器)4、IMP assoservice: unexpected REQ(进纸传感器接触不良或损坏) 十三、打图时图面尺寸不对调整方法先按辅助功能菜单→效准菜单→图纸纵轴线→将默认数值83.82改动，注意图长了则将数字加大，图小了则将数字减小（注，改动时以小数改按每毫米改0.1为准）改后一定要保存。

乐彩 750 写真机常见故障一览表类型：常见问题发表时间：2014-02-19点击：1442乐彩 750 写真机虽然是比较老的款式，但是，在市场上使用的人还是很多的，老款毕竟有不足的地方和一些需要更新的技术，分享到： 1乐彩 750 写真机虽然是比较老的款式，但是，在市场上使用的人还是很多的，老款毕竟有不足的地方和一些需要更新的技术，那么，乐彩科技在对乐彩 750 认真的总结以后，为您提供常见故障、原因分析以及解决方法，详细列表如下：常见故障1、开机不启动、液晶屏不显示故障原因解决方法（2）（3）（ 1）换好用的 220V把装在主板上的1、220V 交流电输出有问如经过前面两项，问电源输出，测量显示屏线、按键拔题；主板、电源板、掉，然后重新启题不没有解决，请更2、24V 主板电源无输出；换主板。

电压应为 24V，动。

3、内存条、显示屏故障；电流应为调整主板显示屏的对比度；具体2、（ 1）机器启动正常，显示（ 1）主板的显示对比度操作方法：设置有问题菜单→使用者设按键线应对准主换按键屏不显示（ 2）按键线未连接好置→液晶显示对板接口插好按显示屏（ 2）显示正常、按键不灵（ 3）按键老化比度，然后进行上下调整，确认保存。

（ 1）纸走偏或“页边尚“页边尚存” 改成用卡纸器防纸走扩展或者初始化3、打印宽度不够存”选“正常”。

换一条原厂的光栅偏重新设置一遍即（ 2）光栅有问题。

可。

进行纵轴线测试：具体操作方法：在1、走纸系统或托架速度主菜单里选择“辅过于快或慢。

把托架速度数值助功能菜单” “颜走纸轮的外径应为，4、打印长度不够2、主板校准设置未保存。

色校准菜单” 图纸调为最佳状态大了走长、小了走短3、用卡尺测量走纸轮的纵轴线测试打印。

外径将测绘的实际数值替代原来的数值5、打印过程中，出现断墨或滴1、供墨管道系统连接松；拧紧贮墨管帽或墨库中墨水的容墨现象，但暂停或抽过墨头之2、墨库与墨头内墨水过加固密封墨头与量应为其 2/3 ，墨后又正常6、机器正常换上纸之后，写真机却无法打印。

富士施乐驱动安装方法
要安装富士施乐驱动程序，您可以按照以下步骤进行操作：
1. 进入富士施乐官方网站，找到支持页面或者驱动程序下载页面。

2. 在支持页面或驱动程序下载页面，选择您的打印机型号和操作系统。

3. 在可用驱动程序列表中，找到与您的操作系统兼容的最新驱动程序，并点击下载按钮。

4. 下载完成后，双击下载的驱动程序安装文件，启动安装向导。

5. 根据安装向导的指示，选择您的安装选项，例如自定义安装或者默认安装。

6. 完成安装后，重新启动电脑。

完成上述步骤后，您的富士施乐驱动程序应该已经成功安装在您的电脑上了。

接下来，您可以使用驱动程序来控制和管理您的打印机。

写真机软件蒙泰的设置方法
作者：admin 发表时间：2009-4-5 17:28:30 阅读：次
国产750户内写真机软件蒙泰的设置方法
1.
电脑设置：
一在CMOS中对打印端口进行设置：
重启电脑，在电脑进行硬件自检时按DEL键进入CMOS设置，进入INTEGRATED PERIPHERALS功能选项，将其中的Parallel Port Mode 设置为ECP（注意：一定要是标准ECP，而不能是EPP、SPP或者ECP/EPP），最后保存并建出BIOS设置，随后，电脑会重新启动，WINDOWS系统自动检测到ECP打印口并为其安装驱动程序，这时，您就可以使用ECP打印口所提供的高速传输性能了。

二如何安装蒙泰
第一步：1 放入光盘于光驱中
2 打开“我的电脑”选择光盘双击
3 双击“蒙泰3”
4 再双击“蒙泰3”
5 双击“SETUP”
6 单击蒙泰DTP V5.0，彩色电子出版系统
7单击确定
8立即重新启动计算机
第二步：1 打开“我的电脑”选择光盘并双击
2 双击“蒙泰3”
3 再双击“蒙泰3”
4 复制“DTPW”到根目录下MainTop/DTP下
5 恭喜你！你已经成功安装蒙泰
1.打开蒙泰，并点击文件文件中的打印机设定
2.选择左下角的安装蒙泰打印机
3.选择安装新打印机，打印机类型选择 ENCAD Novajet ,打印机名字选择novajet750(以750写真机为例)
4。

选定已安装的打印机，novajet750 并设置为默认打印机。

5.打开蒙泰打印管理系统选择您要输出的端口（一般为LPT1）
接下来您就可以直接打印图片了。

NOVAJET750 国产写真机维修手册色静区测试”，打印出测试条后，选择四色各自三细线对的相对较齐整的数值保存即可。

第二步：颜色的水平垂直校正“辅助功能菜单”－>“颜色校准菜单”－>“校准打印测试”，打印出测试条后，对水平和垂直位置进行校正，调整的规律就是“向上和向右增加数值，向下和向左减少数值”。

第三步：图纸纵轴线测试“辅助功能菜单”－>“颜色校准菜单”－>“图纸纵轴线测试”，即在纸上起始端开始走纸，打印出两个“T”字型的图标，用直尺测量交叉点之间的距离，将数值改为测量后的结果即可。

系统默认参数为83.82cm。

三．软件的安装：第一步：在COMS中对打印端口进行设置电脑重启，在电脑进行硬件自检时按DEL键进入COMS 设置，进入INTEGRATED PERIPHERALS功能选项，将其中的Parallel Port Mode设置为ECP（注意：一定要是标准ECP，而不是EPP，SPP或ECP/EPP），最后保存并退出BIOS，随后，电脑会重新启动，windows系统自动检测到ECP打印口并为其安装驱动程序，这时，您就可以使用ECP打印口所提供的告诉传输性能了。

您可以打开“我的电脑”－>右键“属性”－>“硬件”选项卡－>“设备管理器”－>“端口”，如果有显示“ECP打印机端口（LTP1）”，表示您已经设置成功，否则将影响传输速度。

第二步：软件安装打开“蒙太专业版”－>“INSTALL”－>“_INSTALL”双击运行安装即可，安装完毕后打开蒙太软件，选择“文件”－>“打印机设定”，选择“安装蒙太打印机”，打印机类型选择“ENCAD NORAJET”，打印机名选择“NOVAJET 750”，并将输出软件的端口选择为“LTP1”（因为ECP传输协议安装在这个端口）即可。

四．日常注意事项：●打图时要用上卡纸器，以防纸走偏。

●机器工作时必须有人看守，应配备专职的操作员。

DPK750打印机USB接口驱动程序安装帮助✧Windows9x安装帮助✧Windows2000安装帮助✧WindowsXP安装帮助============================================== =======================Microsoft Windows95/98/Me中文版DPK750打印驱动程序安装步骤Version 1.3本版权归南京富士通计算机设备有限公司所有============================================== =======================本DPK750打印驱动程序支持中文版Microsoft Windows95/98/Me(简称Windows95/98/Me)。

通过使用本驱动程序,能够在以下打印机上进行打印：Fujitsu DPK750★注意本打印驱动程序是DPK750用的打印驱动程序。

请不要使用到其他打印机上。

=================================一. 打印驱动程序的工作环境=================================安装Windows95/98/Me中文版的计算机================================= 二. 打印驱动程序的构成=================================DPK750打印驱动程序由以下文件构成：1)USB端口部分USBMON.DLL USB端口监控文件的动态连接库USB.INF USB端口安装用引导文件USBPRINT.SYS USB端口打印功能的动态连接库2)打印机驱动部分750U.DRV DPK系列用打印驱动的本体USB_Print.INF 打印机安装用引导文件UNIDRV.DLL 打印驱动的动态连接库UNIDRV.HLP 打印驱动的帮助文件ICONLIB.DLL 打印图标的动态连接库DMCOLOR.DLL 打印颜色方面的动态连接库================================= 三. 打印驱动程序的安装=================================3.1 安装之前·如果DPK750的打印驱动程序已经安装，请删除后再安装。

godex驱动安装方法Godex驱动安装方法。

为了能够正常使用Godex打印机，首先需要安装相应的驱动程序。

以下是Godex驱动安装的详细步骤。

1. 下载驱动程序。

首先，打开浏览器，进入Godex官方网站。

在官方网站的支持页面或者驱动下载页面，找到适用于您的打印机型号的驱动程序。

一般来说，官方网站会提供最新版本的驱动程序，确保您下载的是最新的版本以获得最佳的兼容性和稳定性。

2. 安装驱动程序。

下载完成后，双击安装程序开始安装。

按照安装向导的提示，选择安装位置和相关设置，然后点击“下一步”继续。

在安装过程中，可能会需要您同意用户协议或者输入管理员密码，根据提示操作即可。

3. 连接打印机。

安装完成后，将Godex打印机与电脑连接。

如果是USB接口的打印机，直接插入电脑的USB接口即可。

如果是网络打印机，确保打印机和电脑在同一个局域网内，然后按照打印机说明书上的网络设置方法进行设置。

4. 配置打印机。

打开控制面板，找到“设备和打印机”选项，可以看到已安装的Godex打印机。

右键点击打印机图标，选择“打印机属性”或者“设置”，进入打印机属性设置页面。

在这里，您可以对打印机进行一些基本设置，比如纸张大小、打印质量等。

根据您的实际需求进行设置。

5. 测试打印。

最后，为了确保驱动安装成功，可以进行一次测试打印。

打开一个文档或者图片，点击“打印”，选择已安装的Godex打印机，然后点击“打印”。

如果打印机正常工作，那么恭喜您，驱动安装成功！总结。

通过以上步骤，您可以轻松地完成Godex驱动的安装。

在安装过程中，如果遇到任何问题，可以参考官方网站提供的帮助文档或者联系Godex客服寻求帮助。

希望本文对您有所帮助，祝您使用愉快！。

一、写真机主面板的介绍二、写真机喷头的校正三、蒙泰软件的安装及设置四、常见故障及解决方法五、常见问题的几点说明六、写真机的日常维护保养面板主菜单：说明：1. 装载打印载体（测纸）2. 切割（不用）3. 暂停（当机器打图时，喷头断线或其他问题时按此键暂停）4. 重新设置（当机器工作中想终止工作时按下此键）当按下“5馈送载体”键后，屏幕显示：馈送载体菜单：说明：此菜单是对载体进行装载操作，可选择“进”或“退”，按“退出”回到主菜单。

当按下“6 设置菜单”后，屏幕显示：设置菜单：说明：一般情况下C，E，F项不能随便更改，建议保持默认数值不变。

当选择A菜单时，屏幕显示：A打印模式菜单说明：各项设置如下:彩色模式（选“彩色”）优质模式（选“使用者自定”）英寸点数（选“600”或“300”，建议选：“600”）每行喷印次数（选“四”或“六”次）托架速度（即小车的行走速度，选“7”或“8”次）打印方向（选“双向”）. 1 .当选择B 菜单时，屏幕显示：B纸张选项菜单打印载体类型（选“卷轴”）打印载体标准（选“全部”）页边留白（选“正常”或“扩展”，建议选择“扩展”）自动装载延迟（选“6”）自动切割（选“关”）节省打印载体（选“开“）自动擦墨（选“开”或“关”）C 菜单用户勿须设定!!!当选择C时，屏幕显示：注意：以上各项禁止随意改动。

当选择D 时，屏幕显示：D使用者设置菜单选择使用者设定（把使用者选定的菜单设置保存在“1—8”中任意一项中）保存使用者设定（所需项选顶后必须保存在“使用者设定菜单”中选定的那一项中）计量单位选择（选“公制”）语种（选“中文”）初始设定值（勿动）打印设定值（勿动）液晶显示对比度（根据实际情况）当选择E时，屏幕显示：墨水选项菜单. 2 .当选择“墨水预热菜单”后，屏幕显示：墨水预热菜单当选择F时，屏幕显示：串口通讯菜单当选择“7辅助功能菜单”时，屏幕显示：7辅助功能菜单说明：各项功能如下:清洗（用于清洗）存取墨水匣（打印过程中用于对喷头进行抽墨等操作）颜色校准菜单（用于喷头的校正）选择“颜色校准菜单“时，屏幕显示：颜色校准菜单选择“校准菜单“时，屏幕显示：校准菜单.3 .选择“颜色静区菜单“时，屏幕显示：颜色静区菜单选择“服务菜单“时，屏幕显示：服务菜单选择“服务菜单”中的“校准菜单”时，屏幕显示：校准菜单选择“诊断菜单”时，屏幕显示：选择“附件菜单”时，屏幕显示：喷头的校正一、喷头的校正分两步1. 颜色的静区校正，具体方法如下：主菜单里选择“辅助功能菜单”“校准菜单”“颜色静区菜单”“颜色静区测试”即在纸上打印出颜色静区测试条2. 颜色的水平垂直校正主菜单里选择“辅助功能菜单”“颜色校准菜单”“校准打印测试”即在纸上打印出颜色校准测试条，二、图纸纵轴线测试主菜单里选择“辅助功能菜单”“颜色校准菜单”“图纸纵轴线测试打印”即在纸上起始端开始走纸,默认参数为:83.82cm. 如果打完偏大或偏少此数值则用打印的实际数值代替原有的数值.注：默认参数 83.82CM不会随更改数值所改变.. 5 .蒙泰软件安装及设置电脑设置：一在CMOS中对打印端口进行设置：重启电脑，在电脑进行硬件自检时按DEL键进入 CMOS设置，进入INTEGRATED PERIPHERALS功能选项，将其中的Parallel Port Mode 设置为ECP（注意：一定要是标准ECP，而不能是EPP、SPP或者ECP/EPP），最后保存并建出BIOS设置，随后，电脑会重新启动，WINDOWS系统自动检测到ECP打印口并为其安装驱动程序，这时，您就可以使用ECP打印口所提供的高速传输性能了。