MS3100F28-12P;中文规格书,Datasheet资料

安徽富信半导体科技有限公司ANHUI FOSAN SEMICONDUCTOR TECHNOLOGY CO.,LTD.SS32F-SS310FSMAF Schottky Barrier Rectifier Diode肖特基势垒整流二极管■Features 特点Low forward voltage drop 低正向压降High current capability 高电流能力Surface mount device 表面贴装器件Case 封装:SMAF■Maximum Rating 最大额定值(T A =25℃unless otherwise noted 如无特殊说明，温度为25℃)Characteristic 特性参数Symbol 符号SS32F SS33F SS34F SS35F SS36F SS38F SS39F SS310F Unit 单位Peak Reverse Voltage 反向峰值电压V RRM 20304050608090100V DC Reverse Voltage 直流反向电压V R 20304050608090100V RMS Reverse Voltage 反向电压均方根值V R(RMS)1421283542566370V Forward Rectified Current 正向整流电流I F 3A Peak Surge Current 峰值浪涌电流I FSM 80AThermal Resistance J-A 结到环境热阻R θJA 10℃/WJunction Temperature 结温T J 150℃Storage Temperature 储藏温度T stg-65to+150℃℃■Electrical Characteristics 电特性(T A =25℃unless otherwise noted 如无特殊说明，温度为25℃)Characteristic 特性参数Symbol 符号SS32F-SS34F SS35F-SS36F SS38F-SS310F Unit 单位Condition 条件Forward Voltage 正向电压V F 0.550.700.85V I F =3A Reverse Current 反向电流I R (25℃)(100℃)0.150.022mA V R =V RRM Diode Capacitance 二极管电容C D300pFV R =4V,f=1MHzANHUI FOSAN SEMICONDUCTOR TECHNOLOGY CO.,LTD.SS32F-SS310F ■Typical Characteristic Curve典型特性曲线ANHUI FOSAN SEMICONDUCTOR TECHNOLOGY CO.,LTD.SS32F-SS310F ■Dimension外形封装尺寸。

1-15/32
—
7/8
1-1/8
—
3/4-20
—
—
(Continued)
More Product Available Online:
194
(T032)
Toll-Free: 1-800-344-4539 • Phone: 218-681-6674 • Fax: 218-681-3380
CONTACT LEGEND
16 12 8
SERVICE RATING: INST A D E Limited Operating DC 250 700 1250 1750 Voltages at Sea Level AC(rms) 200 500 900 1250 TEST CURRENT: Contact Size 16 = 13 amperes, Contact Size 12 = 23 amperes NOTE: Transients were not considered in calculating these values. NOTE: Limiting operating voltage at 50,000 feet altitude are approx. 25% of the sea level values. B 2450 1750 C 4200 3000
Panel Opening
O
Insert Arrangement Service Rating
CA B A B
A B A C A B C D A B A B E D C F E D B
C A B
F G A E D C B D C B E A
B C A D I J A
(T000)
000

POTTING ER CONNECTORS (Solder Contact Termination) These lightweight potting connectors provide resistance to salt water, fuels, etc., and will withstand the effects of high vibration. 3100 and 3106 connectors with plastic potting cups and resilient inserts meet the requirements of MS3103 and MS25183. Contacts are silver plated copper or brass. ER insulators are resilient; shells are aluminum alloy. A 90˚ plug (3108ER) is also available.
PREFIX
CA 3106 R 20 - 27 P W * MS 3106 R 20 - 27 P W -
SHELL STYLE
CLASS
SHELL SIZE
CONTACT ARRANGEMENT
CONTACT TYPE
ALTERNATE INSERT POSITION
MODIFICATION CODE
MATERIALS AND FINISHES
Shell
Material
Finish
Insulator Contacts
Material Material Finish Termination
How to Order
In the latest revision of MIL-C-5015, a new class of environment-resistant connectors was added. This new class F connector supersedes the previous class E connector. The MS3106F is identical to the MS3106E except that the MS3106F has an "0" ring under the coupling nut. The class E will still be available upon request for exitsting programs, and upon ordering will also bear the E nomenclature on the shell. MS-F and MS-R connectors are designed to operate in the extreme environmental conditions of high altitude filight and must be completely sealed to withstand moisture, condensation, vibration, corona and flashover caused by high altitude environments. They have resilient grommet with internal restrictions in the wire cavities which act as 0 rings around the wires. This allows the wires to slide thru the grommet with a minimum of friction, yet when the ferrule is seated and the endbell tightened it provides a perfect wire seal thru a wide variety of wire diameters. This seal at the rear, plus the interfacial seal at the front, effects a completely environment-resistant asssembly when the plug is mated to and F or R receptacle. Sockets are of the closed-entry type. The temperature range for this connector is -55˚C (-67˚F) to +125˚C (+257˚F) and meets the requirements of MIL-C-5015. The F80 modification (crimp contact termination) is avialable in resilient insulators in the E, R, F, and BFR styles, creating a large selection of insert assemblies and hardware. Components are identical to the MS-5015 except that the contacts are modified for crimp termination providing and inexpensive crimp contact connector with the proven reliability of and complete intermateability with the MS-5015 series. See page 187 for assembly instructions. Cable clamps have been integrally designed with the endbell on MS-E and MS-F connectors. Class R is without the cable clamp.

IR
C
SYMBOLS
MARKING CODE SS32 SS33 SS34 SS35 SS36 SS38 S310
V RRM
*1
V RMS
*2
VR
*3
VF
*4
Operating temperature (o C)
(V) FM320-ALN FM330-ALN FM340-ALN FM350-ALN FM360-ALN FM380-ALN FM3100-ALN 20 30 40 50 60 80 100
0.040(1.0) Typ.
SMA-LN
0.205(5.2) 0.189(4.8) 0.012(0.3) Typ.
0.110(2.8) 0.094(2.4)
0.181(4.6) 0.165(4.2)
0.075(1.9) 0.067(1.7)
0.040 (1.0) Typ.
0.067(1.7) 0.053(1.3)
FIG.2-TYPICAL FORWARD CHARACTERISTICS
3.0 2.5
35 FM
50
INSTANTANEOUS FORWARD CURRENT,(A)
FM FM 35 32 00AL FM AL N~ 38 N FM 0~F AL 36 M N~ 034 AL FM 0N AL 31 N 00 -A LN
10 3.0 1.0
1 M3 ~F 00 N -AL
100
LN 0-A
120
140
160
180
200
Tj=25 C Pulse Width 300us 1% Duty Cycle
0.1
80
.01