太阳能手机充电器使用说明书

太阳能充电器的使用指南在现代社会中，电子设备已经成为了人们生活中不可或缺的一部分。

然而，电子设备的使用过程中，常常会遇到电池电量不足的问题。

为了解决这一问题，太阳能充电器应运而生。

太阳能充电器以太阳能作为能源，可以为电子设备充电，不仅环保节能，而且方便实用。

本文将为大家介绍太阳能充电器的使用指南。

一、了解太阳能充电器的原理太阳能充电器的工作原理是通过太阳能电池板将太阳能转化为电能，再将电能储存在内置的电池中，最后通过输出接口为电子设备充电。

因此，在使用太阳能充电器之前，我们需要了解充电器的工作原理，这有助于我们更好地使用充电器。

二、选择适合自己的太阳能充电器市场上有各种各样的太阳能充电器，我们可以根据自己的需求选择适合自己的充电器。

首先，我们需要考虑充电器的功率。

太阳能充电器的功率越大，充电速度就越快。

其次，我们需要考虑充电器的便携性。

如果我们需要经常外出旅行或者露营，那么选择一个小巧轻便的太阳能充电器会更加方便携带。

最后，我们还可以考虑充电器的附加功能，例如防水、防震等，以适应不同的使用环境。

三、正确使用太阳能充电器1. 找到合适的充电位置太阳能充电器需要暴露在阳光下才能正常工作，因此我们需要找到一个合适的充电位置。

通常情况下，阳光直射的地方是最佳的充电位置。

同时，我们还需要注意避免充电器暴露在高温或者潮湿的环境中，以免影响充电器的寿命和性能。

2. 定期清洁充电板太阳能充电器的充电板容易受到灰尘、污垢等物质的影响，影响充电效果。

因此，我们需要定期清洁充电板，保持其表面清洁。

可以使用软布轻轻擦拭充电板，注意不要使用刷子或者其他硬物来清洁，以免刮伤充电板。

3. 注意充电器的安全使用在使用太阳能充电器的过程中，我们需要注意一些安全事项。

首先，不要将充电器暴露在高温环境中，以免损坏充电器或者导致安全问题。

其次，不要将充电器放置在易燃物附近，以免引发火灾。

最后，不要将充电器浸泡在水中，以免损坏充电器。

四、充电器的适用范围和注意事项太阳能充电器适用于大部分电子设备，例如手机、平板电脑、相机等。

1. 2. 可通过拨码开关选择4种电池。

GEL 电池,铅酸(液体)电池，AGM 2电池，LiFePO4磷酸铁锂电池3. 带负载输出功能，具有过放，过载，短路保护功能。

4. 带蓝牙功能，可以通过手机APP 显示查看控制器参数(仅MPPT 5020-BT,MPPT5040-BT )5. 具有RS 485通信功能，便于终端设备可靠的读取到控制器的运行参数(仅6. 全自动无人值守充电。

具有过载，过热，反向电流保护（阴天或者晚上无阳光的时候，防止蓄电池倒灌到太阳能板）7. 过充保护。

当电池充满的时候 ,充电电流会减小，当蓄电池没电的时候，会立即给蓄电池充电8. 自动温度补偿功能。

确保电池在低温或者高温的环境下，采用最佳的充电参数，延长蓄电池的使用寿命强烈建议,不要把蓄电池和控制器安装在发热源的地方,以免引起控制器的误操作提高充电电流，相比传统的PWM 控制器，MPPT 充电效率可以提高10-30%。

(控制器转换效率>95%)MPPT 5020-COM,MPPT5040-COM)使用说明书太阳能充放电控制器MPPT1. 只能给符合额定电压的GEL 电池，铅酸液体电池，AGM 电池，磷酸铁锂(必须带MBS)电池充电2. 太阳能板功率尽量使用控制器最大额定功率以内的太阳能板3. 连接电缆的线径参考工厂的建议值。

如果电缆过小,会导致电缆过热和能量损耗4. 在靠近电池端的附近安装额定规格的保险丝，用来保护蓄电池和太阳能板之间的电缆5. 请安装在通风良好的房间内，防止雨水，潮湿，灰尘，侵蚀性的电池气体以及在环境没有冷凝水6. 本机出售时候，不配任何配件。

如果需要更换部品，请联系供应商7. 控制器和电池请远离儿童.带APP 显示或者RS485通信功能MPPT5020-BT MPPT5020MPPT5040MPPT5040-BT MPPT5020-comMPPT5040-com 适用 铅酸(液体,AGM ,GEL )电池 LiFePO4磷酸铁锂电池-1 2胶体电池(GEL )密封铅酸(Lead-acid )AGM↑↑↑↑Note:连接电缆的时候请仔细看清控制器上的标识，绝对不能把极性接错，否则可能导致控制器损坏。

太阳能电池板智能充电器使用说明书充电及超压指示：当系统连接正常，且有阳光照射到光电池板时，充电指示灯(1)为绿色常亮，表示系统充电电路正常；当充电指示灯(1)出现绿色快速闪烁时，说明系统过电压，处理见故障处理内容；充电过程使用了PWM方式，如果发生过过放动作，充电先要达到提升充电电压，并保持30分钟，而后降到直充电压，保持30分钟，以激活蓄电池，避免硫化结晶，最后降到浮充电压，并保持浮充电压。

如果没有发生过放，将不会有提升充电方式，以防蓄电池失水。

这些自动控制过程将使蓄电池达到最佳充电效果并保证或延长其使用寿命。

蓄电池状态指示：蓄电池电压在正常范围时，状态指示灯(2)为绿色常亮；充满后状态指示灯为绿色慢闪；当电池电压降低到欠压时状态指示灯变成橙黄色；当蓄电池电压继续降低到过放电压时，状态指示灯(2)变为红色，此时控制器将自动关闭输出，提醒用户及时补充电能。

当电池电压恢复到正常工作范围内时，将自动使能输出开通动作，状态指示灯(2)变为绿色；负载指示：当负载开通时，负载指示灯(4)常亮。

如果负载电流超过了控制器1.25倍的额定电流60秒时，或负载电流超过了控制器1.5倍的额定电流5秒时，故障指示灯(3)为红色慢闪，表示过载，控制器将关闭输出。

当负载或负载侧出现短路故障时，控制器将立即关闭输出，故障指示灯(3)快闪。

出现上述现象时，用户应当仔细检查负载连接情况，断开有故障的负载后，按一次按键即恢复正常输出。

负载开关操作：控制器上电后默认负载输出为关闭，在正常情况下，每按一次按键，负载输出即改变一次开关状态。

当负载输出为开时，负载指示灯(4)常亮；当负载为关闭时，负载指示灯(4)常灭；当负载过载时，故障指示灯(3)慢速闪烁，当负载发生短路时，故障载指示灯(3)快速闪烁。

负载过载或短路控制器均会关闭输出。

第一次发生负载短路30秒后自动恢复输出若还没排出短路故障只能手动恢复输出。

如复位过载、短路保护，排出负载的短路或过载故障，按一次按键，即恢复正常输出。

太阳能充电器使用说明书本产品是一款多功能太阳能应急充电器，内置1200mAh高容量可充电锂电池，可随时随地对您的手机、数码相机、PDA、MP3、MP4等数码产品进行充电。

造型华贵大方，小巧玲珑，携带方便，时尚高雅。

使用方法1、使用之前请给您的太阳能充电器充电，有三种方法可以选择：a、将充电器放置于太阳光直射处，太阳能将转化为电能给充电器内置可充电电池充电。

b、将充电器USB线连接电脑，此时充电器指示灯会闪光，表示正在充电，当充电满后，此灯将会熄灭。

C、用交流适配器充电，充电时指示灯会闪光，当充电满后此灯将会熄灭（因为设计有自动断电保护）2、将转换接头连接到延长线，再将延长线的另一头连接到充电器，或直接将转接头连接到充电器。

3、将转换接头连接到您的手机或其它数码产品。

4、从您的手机或其它数码产品上将可看到正在充电，充电的同时您也可以用手机通话。

5、太阳能充电指示。

将开关拨到‘NO’，太阳能板在接受阳光照射时，太阳能充电指示呈绿色。

产品特点：1、特别适用于应急场合。

当您在野外作业或旅游，或者遇到停电时，太阳能充电器将会帮您的大忙，使您的手机随时随地保持工作状态，让您不间断的与您的朋友和家人保持联系。

2、使用方便无论何时何地，您都可以极为方便的给您的手机或其它数码产品充电。

3、高效率充电给您的手机充电60分钟，可以获得100-150分钟通话时间4、环保、节约能源使用绿色能源太阳能，可为环保作出您的贡献。

5、外形时尚，携带方便造型简洁华贵，超薄不锈钢外壳设计，小巧玲珑，携带方便。

6、使用安全带有充电过充保护，有效延长您的手机电池的使用寿命，使用安全。

产品规格1、使用高转换效单晶硅或多晶硅片，太阳能转换效率高达15%以上。

2、太阳能电池板规格：5.5V/80mA。

3、充电时内置高容量可充电锂电池：1200 mAh。

4、输出电压：5.5V。

5、输出电流：1000mA。

6、充电器给手机充电时间：约60分钟（不同品牌和型号的手机有少许差别）。

太阳能充电器说明书规格参数太阳能输出: 5V/2400mA（阳光充足下）输入：5V/2A 输出：5V/3A（max）功能指示1 外接太阳能充电器并接输入端口2 太阳能充电指示灯3 USB输出端口4 大功率单晶硅太阳能板5 挂绳孔批准：审核：编制：产品简介· 本产品为户外便携式太阳能充电包，小巧玲珑，方便携带。

配备6片大功率的单晶硅太阳能板，高达 20％ 的转换率，输出电流高达2400mA, 为您的手机、IPAD或其他小设备充电。

在享受大自然阳光的同时为您提供源源不断的绿色能源，是您外出旅游出行的必备佳品。

为设备充电1、在有阳光的地方打开太阳能产品，使太阳能板接受太阳的45°照射，太阳能指示灯绿灯亮，这时USB输出可以输出高达5V/2.4A的电流为您的电子产品进行充电。

2、为获得更大的电流，此产品可以两个并联使用，并联后可以获得最大5V/3A的电流，实现快速充电。

温馨提示：本产品需要在阳光下使用。

本太阳能面板不能直接存储电源，如果您想存储电源，您可以使用它为移动电源充电。

如果产品不能工作，请检查 USB 接口是否正确插入太阳能面板。

工作后请记住，卸下USB插头。

12345User manualSpecification parameterSolar charging :5V/2400mA(In full sunshine)Input :5V/2AOutput :5V/3A （max ）批准：审核：编制：·Product introduction·The product is an outdoor portable solar chager, small and exquisite, easy to carry. Equipped with 6 high-power mono-crystalline silicon solar panels, high transmit efficiency 20%, up to 2400mA max charging current, It can charge mobile phone ，IPAD or other small mobile devices. It willprovide you with green energy while enjoying the natural sunshine ,which will be your travelnecessity.Charger the device1、Open the solar energy product in a place with sunlight, so that the solar panel receives 45° illumina-tion from the sun, the solar indicator is green, and the USB output can up to 5V/2.4A to charge your electronic products.2、For more current , It can be used in parallel for two or three products. After parallel ,the maximum current output : 5V/3A can be obtained to achieve fast charging.Tips: This product needs to be used in the sun. This solar panel cannot store power directly. If you want to store power, you can use it to charge mobile power. If the product does not work, check that the USB connector is properly inserted into the solar panel. Remember to remove the USB plug after work.Function indication1.External solar charger connected to the input port2.Solar charging indicatorB output port4.High power mono-crystalline silicone solar panelnyard hole12345。

SAVE THESE INSTRUCTIONS Solar Powered Smartphone Charger User ManualItem # 80082V1.1-M 27Sep2019WARNING:Read carefully and understand all assembly and operation instructions before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury.Important Safety InformationThank you for choosing a Nature Power Product.Save the receipt and these instructions. It is important that you read the entire manual to become familiar with this product before you begin using it.This product is designed for certain applications only. the distributor cannot be responsible for issues arising from modification. We strongly recommend this product not be modified and/or used for any application other than that for which it was designed. If you have any question relative to a particular application, Do not use the product until you have first contacted the distributor to determine if it can or should be performed on the product.For technical question please call 1800-588-0590This solar charger is uniquely constructed with integrated Li-polymer 8000mAh battery.It has features of Waterproof, Dustproof, Shockproof .Dual USB output,LED lights.Page 2 of 4Never attempt to open or disassemble the solar charger.Never subject the solar charger to knock or blow.Do not let children play with the solar charger.The solar charger is waterproof but only for rains. Never be immersed in water or any other liquid.Do not leave the solar charger in airtight space when sunshine charging such as in car,may cause the maximum operating temperature(65℃)being exceeded.Do not throw the solar charger into the fire.Parts List1, Charging the solar charger via the solar panel.Place the solar charger under sunlight. the green LED indicator will keep on when the solar charger is charging by sunlight. When the solar charger is fully charged, LED indicators will be off.NOTE: Solar charging is only emergency charging method,please avoid prolonged exposure under the burning sun.2, Charging the solar charger from an external power source.Connect the solar charger's cable to a computer or laptop USB port, USB car charger or USB AC charger. blue led indicators are flashing to indicate that the solar charger is being charged. when the solar charger is fully charged. led indicators will be off.An external power source takes 5-8 hours to fully charge the solar charger.Page 3 of 43, Charging device.after 20 seconds.4, LEDKeep pressing the button for 2 seconds to turn on the 20LED light.Keep pressing the button for 2 times to turn on the single LED flashlight. 2 more times to turn off.When the 20LEDs on, single press the button to reduce luminance;Under low-light mode, single press the button to turn into SOS signal mode;Under SOS signal mode, single press the button to turn back to high light mode;Under high-light mode, pressing the button for 2 seconds to turn off the 20LED light.5, Power indication:Press the button to check the remain battery capacityLED Light(●ON ○OFF) Capacity○○○○ 0%●○○○ 0%-25%●●○○ 25%-50%●●●○ 50%-75%●●●● 75%-100%NOTE:1, When the solar charger is in use and the remained capacity in solar charger is less than 2%, the solar charger will automatically shut off in order to avoid over-discharge of the battery. When the solar charger begins to recharge, it takes 3 minutes before it can output any charging current.2, Because of the special Settings of Apple Corp, please use the apple original data cables when charging for Apple products.3, The Waterproof design can effectively avoid the accident in the process of use, but should avoid power bank in the water or other dangerous environments.Limited WarrantyNature Power warrants our products to the original purchaser that this product is free from d efects in materials and workmanship for the period of 1 year from date of purchase, In the case of pro duct defect, contact Nature Power customer service to receive trouble shooting. If defective part or unit s hould be returned, a Return Authorization Number must be issued by Nature Power and the defective part or unit should be returned to the authorized location at the purchasers’ expense. A dated proof of p urchase is required to receive warranty service. Once received at authorized location and defect prove s to be the result of defective material and workmanship, the defective part or unit will be replaced at w arrantors’ option and returned to the original purchaser at warrantors’ expense. No refunds will be gran ted by the warrantor, in the event of buyer’s remorse please contact your point of purchase within and in adherence to their return policy. Refunds are granted at the retailers’ discretions.Please contact Nature Power Products to acquire more information:1-800-588-0590****************************Made in ChinaPage 4 of 4。

Operating manualSolar charge controller10.10 A / 8.8 A / 6.6 APlease read these instructions completely before installation!1. About this manualThese operating instructions are part of the product. Read these operating instructions carefully before use, keep them over the entire lifetime of the product, and pass them on to any future owner or user of this product.This manual describes the installation, function, operation and maintenance of the solar charge controller. These operating instructions are intended for end customers.A technical expert must be consulted in cases of uncertainty.2. SafetyThe solar charge controller may only be used in PV systems for charging and controlling lead-acid batteries in accordance with this operating manual and the charging specifications of the battery manufacturer.The solar charge controller may only be connected to the local loads and the battery by trained personnel and in accordance with the applicable regulations. Follow the installation and operating instructions for all components of the PV system.No energy source other than a solar generator may be connected to the solar charge controller. Follow the general and national safety and accident prevention regulations.Keep children away from PV systems. Do not use the solar charge controller in dusty environments, in the vicinity of solvents or where inflammable gases and vapours can occur. No open fires, flames or sparks in the vicinity of the batteries. Ensure that the room is adequately ventilated. Check the charging process regularly.Follow the charging instructions of the battery manufacturer. Battery Acid splashes on skin or clothing should be immediately rinse with plenty of water. Seek medical advice.Do not operate the solar charge controller when it does not appear to function at all. The solar charge controller or connected cables are visibly damaged or loose. In these cases immediately remove the solar charge controller from the solar modules and battery.3. FunctionsThe solar charge controller monitors the state of charge of the battery bank, controls the charging process, controls the connection/disconnection of loads. This optimises battery use and significantly extends its service life.The following protection functions are part of the basic function of the controller: Overcharge protection ; Deep discharge protection ; Battery undervoltage protection ; Solar module reverse current protection.4. Installation4.1 Mounting location requirementsDo not mount the solar charge controller outdoors or in wet rooms. Do not subject the solar charge controller to direct sunshine or other sources of heat. Protect the solar charge controller from dirt and moisture.Mount upright on the wall (concrete) on a non-flammable substrate. Maintain a minimum clearance of 10 cm below and around the device to ensure unhindered air circulation. Mount the solar charge controller as close as possible to the batteries (with a safety clearance of at least 30 cm).4.2 Fastening the solar charge controllerMark the position of the solar charge controller fastening holes on the wall.Drill 4 Ø 6 mm holes and insert dowels. Fasten the solar charge controller to the wall with the cable openings facing downwards, using 4 oval head screws M4x40 (DIN 7996).4.3 ConnectionUse an wire size suited to the current ratings of the charge controller, e.g. 6mm² for 10A, 5 mm² for 8A, 4 mm² for 6A, 3 mm² for 5A for cable length of 10 m.An additional external 20A fuse (not provided) must be connected to the battery connection cable, close to the battery pole. The external fuse prevents cable short circuits.Solar modules generate electricity under incident light. The full voltage is present, even when the incident light levels are low. Protect the solar modules from incident light during installation, e.g. cover them.Never touch not isolated cable ends. Use only insulated tools. Ensure that all loads to be connected are switched off. If necessary, remove the fuse.Connections must always be made in the sequence described below.1st step: Connect the batteryConnect the battery connection cable with thecorrect polarity to the middle pair of terminalson the solar charge controller (with the batterysymbol).If present, remove any external fuse. Connectbattery connection cable A+ to the positivepole of the battery. Connect batteryconnection cable A– to the negative pole ofthe battery. Insert the external fuse in thebattery connection cable.If the connection polarity is correct, the infoLED illuminates green.2nd step: Connect the solar moduleEnsure that the solar module is protected from incident light (cover it or wait for night).Ensure that the solar module does not exceed the maximum permissible input current.First connect the M+ solar module connection cable to the correct pole of the left pair ofterminals on the solar charge controller (with the solar module symbol), then connect theM– cable. Remove the covering from the solar module.3rd step: Connect loadsFirst connect the L+ load cable to the correct pole of the right pair of terminals on the solarcharge controller (with the lamp symbol), then connect the L– cable. Insert the load fuse orswitch on the load.Notes : Connect loads that must not be deactivated by the solar charge controller deepdischarge protection, e.g. emergency lights or radio connection, directly to the battery.Loads with a higher current consumption than the device output can be directly connectedto the battery. However, the solar charge controller deep discharge protection will no longerintervene. Loads connected in this manner must also be separately fused.4th step: Final workFasten all cables with strain relief in the direct vicinity of the solar charge controller(clearance of approx. 10 cm).5. LED displaysLED Status Meaningilluminates green normal operationInfo LEDflashes slowly red* system fault- too high charging current- overload / short circuit- overheatedtogether with red LED :- too low battery voltagetogether with green LED :- too high battery voltageflashing quickly* battery empty, low voltage disconnectionprewarning, loads still onBatteryredLED flashing slowly* deep discharge protection active (LVD), loadsdisconnectedilluminates battery weak, loads are onBatteryyellowLEDflashes slowly yellow* LVD reconnection setpoint has not yet beenreached, loads still disconnectedilluminates battery goodBatterygreenLEDflashes quickly green* battery full, charge regulation active*flashing slowly: 0,4Hz: 4 times in 10 second, flashing quickly: 3Hz: 3 times in 1 second6. GroundingThe components in stand-alone systems do not have to be grounded – this is not standardpractice or may be prohibited by national regulations (e.g.: DIN 57100 Part 410: Prohibitionof grounding protective low voltage circuits). Ask your dealer for technical assistance.7. Lightning protectionIn systems subjected to an increased risk of overvoltage damage, we recommendinstalling additional lightning protection / overvoltage protection to reduce dropouts.Ask your dealer for technical assistance.8. MaintenanceThe solar charge controller is maintenance-free.All components of the PV system must be checked at least annually, according to thespecifications of the respective manufacturers. Ensure adequate ventilation of the coolingelement. Check the cable strain relief. Check that all cable connections are secure. Tightenscrews if necessary. Check corrosion on terminals.9. Faults and remediesNo display : Check battery polarity and external fuse. Or battery voltage is too low orbattery defective.Battery is not charged : Check if solar modul is connected with correct polarity or if shortcircuit at the solar input. If solar module voltage is lower than battery voltage or if solarmodule is defective the battery cannot be charged.Battery displays jumps quickly : Battery voltage changes quickly. Large pulse currentscause voltage fluctuation. Battery is too small or defective. Ask your dealer for technicalassistance.The following faults do not destroy the controller. After correcting the fault, the device willcontinue to operate correctly:* solar module short circuits * reverse solar module polarity *2* short circuits at load output * excessive load current* reversed battery polarity *1* solar module overcurrent* device overtemperature * overvoltage at the load output10. Legal guaranteeAccording to the German legal requirements, for this product the customer has a 2 yearlegal guarantee.The seller will remove all manufacturing and material faults that occur in the product duringthe legal guarantee period and affect the correct functioning of the product. Natural wearand tear does not constitute a malfunction.Legal guarantee does not apply if the fault can be attributed to third parties, unprofessionalinstallation or commissioning, incorrect or negligent handling, improper transport, excessiveloading, use of improper equipment, faulty construction work, unsuitable constructionlocation or improper operation or use.Legal guarantee claims shall only be accepted if notification of the fault is providedimmediately after it is discovered. Legal guarantee claims are to be directed to the seller.The seller must be informed before legal guarantee claims are processed.For processing a legal guarantee claim an exact fault description and the invoice / deliverynote must be provided. The seller can choose to fulfil the legal guarantee either by repair orreplacement.If the product can neither be repaired nor replaced, or if this does not occur within asuitable period in spite of the specification of an extension period in writing by thecustomer, the reduction in value caused by the fault shall be replaced, or, if this is notsufficient taking the interests of the end customer into consideration, the contract iscancelled. Any further claims against the seller based on this legal guarantee obligation, inparticular claims for damages due to lost profit, loss-of-use or indirect damages areexcluded, unless liability is obligatory by German law.11. Technical DataSteca Solsum F 6.6F 8.8F 10.10FSystem voltage 12 V (24 V)Own consumption < 4 mADC input sideOpen circuit voltage solar module(at minimum operating temperature)< 47 VModule current 6 A 8 A 10 ADC output sideLoad current 6 A 8 A 10 AEnd of charge voltage 13.9 V (27.8 V)Boost charge voltage 14.4 V (28.8 V)Reconnection voltage (SOC / LVR) *³> 50 % / 12.4 V … 12.7 V(24.8 V … 25.4 V)Deep discharge protection (SOC / LVD) *³< 30 % / 11.2 V … 11.6 V(22.4 V … 23.2 V)Operating conditionsAmbient temperature -25 °C … +50 °CFitting and constructionTerminal (fine / single wire) 4 mm2 / 6 mm2 - AWG 12 / 9Degree of protection IP 32Dimensions (X x Y x Z) 145 x 100 x 24 mmWeight approx. 150 g*1Solsum is protected against reverse battery polarity together with polarity protectedloads. Reverse battery polarity combined with short circuited or polarised load couldcause damages in load or regulator*2Avoid reverse module polarity in a 24V system*3Lower value for nominal current, higher value for lowest currentInfo LED Battery LEDsManufactured in aDIN EN ISO 9001:2000 facilitySolsum / Z02 / Version 1104/ 730.930。

太阳能智能充电器/移动电源一、产品介绍：本产品是一款多用途的太阳能智能充电器/移动电源，内置高容量可充电聚合物锂电池，太阳能电池板功率最高可达1.6w。

通过智能MCU输出多组电压，可随时随地对你的手机、数码相机、PDA、PSP、GPS、DV、MP3、MP4家庭节能设备等进行充电或供电。

本产品具有安全可靠，容量大，寿命长，功能多等优点。

金属外壳设计、时尚高雅、携带方便。

二、使用方法：注：本产品在初次使用时，请在使用前对本产品进行两次以上完全充、放电，以提高内置电池的使用效率。

请按下面步骤使用：1、使用之前请给本产品充电。

有三种方法可选择：A、太阳能充电:打开产品，放置于太阳直射处或强光上，太阳光将自动转化为电能自动为内置的锂电池进行充电。

此时产品的LED指示灯为红色，表示正在充电，当电池充满后，LED指示灯将变为绿色。

（内部设计电路有自动断电保护功能）B、电脑USB对产品充电:将产品用USB线连接到电脑USB端口，此时产品的LED指示灯为红色，表示正在充电，当电池充满后，LED指示灯将变为绿色。

（内置先进的电源管理芯片不会对你的PC产生任何的危害）C、用交流适配器充电：充电时USB指示灯会亮起，产品的LED指示灯为红色，表示正在充电，当电池充满后，LED指示灯将变为绿色，并关闭所有的输出。

另外，还可使用车载充电器对本产品充电。

2、当给您的手机或数码产品充电前，请仔细查看您的产品说明书或电源适配器，了解您产品的充电电压，然后按ON／OFF按钮(3秒一5秒)即可开机，开机时，红色LED电压指示灯亮，开机后产品默认输出4．8V，长按调节按钮(3秒一5秒）即可以调节输出4．8、5．8V、8．4V、9.0V。

每长按一次，可调整一次电压输出，调节好电压后，将充电转换线的USB 5P插头连接到本产品，再将另一头与相应的转接头连接，然后再连接到您的产品上，即可进行充电。

充电时，在您的手机和数码产品上将显示正在充电的提示，您可以在进行充电的同时使用手机进行通话。