电子烟说明书一、产品介绍电子烟是一种电子化烟草产品，其工作原理是通过加热和雾化液体尼古丁，用户吸入这些雾化物以模拟传统烟草香烟的使用体验。
电子烟由电池、雾化器和储存液组成。
本说明书将详细介绍电子烟的使用方法、注意事项以及维护保养。
二、使用方法1. 充电将电子烟充电器插入电源插座，并将电子烟连接到充电器上。
等待充电指示灯亮起，表示正在充电。
待电子烟充满电后，拔出充电器并断开与电源的连接。
2. 组装取下电子烟的雾化器盖，将烟嘴连接到雾化器并顺时针旋转以固定。
确保烟嘴与雾化器紧密连接。
3. 加液体取下雾化器并将液体注入至雾化器内。
请注意不要超过雾化器容量的80%。
之后将雾化器安装回电子烟并紧固。
4. 启动按下电池上的启动按钮，电子烟将开始加热并产生雾气。
开始吸烟前请等待几秒钟，确保电子烟正常工作。
5. 吸烟将电子烟烟嘴放入口中，并轻吸几口即可。
请注意不要太用力吸烟，并避免在不适当的场合吸烟。
三、注意事项1. 孕妇、哺乳期妇女、未成年人以及不吸烟的人士应避免使用电子烟。
2. 请勿将电子烟置于高温或潮湿的环境中，以免损坏电池和雾化器。
3. 在使用过程中，请确保电子烟周围没有易燃物品，以免发生安全事故。
4. 请勿尝试修理电子烟，如有故障请联系售后服务中心。
5. 若长时间不使用电子烟，请将其存放在干燥通风的地方，并将电池取出以节省电力和延长电池寿命。
四、维护保养1. 定期清洁雾化器，避免残留物堵塞雾化器。
2. 请使用原装电池和充电器，避免使用不合格的电池和充电器，以免引发安全问题。
3. 若电子烟出现异常现象，如发生漏液、漏气等情况，请停止使用并联系售后服务中心进行维修。
五、温馨提示1. 电子烟仅适用于成年吸烟人群，严禁销售给未成年人。
2. 请妥善保管电子烟，避免与儿童接触。
3. 请勿吸入过量尼古丁，以免对健康造成不利影响。
4. 本产品不适用于禁烟人群或患有呼吸系统疾病的人士。
六、免责声明电子烟是一种化学产品，使用时请遵循以上说明，若因未正确使用或不当维护而产生的任何问题或危害，我们不承担任何责任。
SS-400-0051I56-3578-0002251BRA Intelligent Photoelectric Smoke Sensor with Remote Test Capability in Duct ApplicationsINSTALLATION AND MAINTENANCE INSTRUCTIONSBEFORE INSTALLINGThis sensor must be installed in compliance with the control panel system installation manual. The installation must meet the requirements of the Au-thority Having Jurisdiction (AHJ). Sensors offer maximum performance when installed in compliance with CAN/ULC-S524.GENERAL DESCRIPTIONModel 2251BRA is a plug-in type smoke sensors that combines a photo-electronic sensing chamber with addressable-analog communications. The sensor transmits an analog representation of smoke density over a communi-cation line to a control panel. Rotary-decade switches are provided for setting the sensor’s address.Two LEDs on the sensor are controlled by the panel to indicate sensor status. An output is provided for connection to an optional remote LED annunciator (P/N RA400ZA/RA100ZA).When 2251BRA is used in duct applications with a DNRA, testing can be done remotely using approved System Sensor test accessories, eliminating the need for a test coil.NOTE: Only System Sensor approved accessories may be used with the 2251BRA.The 2251BRA requires compatible addressable communications to function properly. Connect the 2251BRA sensor to listed-compatible control panels only.SPACINGSystem Sensor recommends spacing sensors in compliance with CAN/ULC-S524. In low air flow applications with smooth ceilings, space sensors 30 feet apart. For specific information regarding sensor spacing, placement, and special applications, refer to CAN/ULC-S524 or the System Smoke Detector Application Guide, available from System Sensor.Duct Applications: 2251BRA is listed for use in ducts. See Duct Applications Guide A05-1004-XX.WIRING GUIDEAll wiring must be installed in compliance with the Canadian Electrical Code, applicable local codes, and any special requirements of the Authority Hav-ing Jurisdiction. Proper wire gauges should be used. The installation wires should be color-coded to limit wiring mistakes and ease system troubleshoot-ing. Improper connections will prevent a system from responding properly in the event of a fire.Remove power from the communication line before installing sensors.1. Wire the sensor base (supplied separately) per the wiring diagram, Figure 1.2.S et the desired address on the sensor address switches, see Figure 2.3.I nstall the sensor into the sensor base. Push the sensor into the base while turning it clockwise to secure it in place.4.A fter all sensors have been installed, apply power to the control unit and activate the communication line.5.T est the sensor(s) as described in the TESTING section of this manual.SPECIFICATIONSOperating Voltage Range: 15 to 32 VDCStandby Current:300µA @ 24 VDC (one communication every 5 seconds with LED blink enabled)Maximum Alarm Current (LED on:) 6.5 mA @ 24 VDCOperating Humidity Range: 10% to 93% Relative Humidity, Non-condensing Operating Temperature Range: 32°F to 120°F (0°C to 49°C) 2251BRA–4°F to 158°F (–20°C to 70°C) 2251BRA in duct applications Height: 2.0˝ (51 mm) installed in B210LPA BaseDiameter: 6.1˝ (155 mm) installed in B210LPA Base; 4.1˝ (104 mm) installed in B501 Base Weight:5.2 oz. (147 g)Dust covers provide limited protection against airborne dust particles dur-ing shipping. Dust covers must be removed before the sensors can sensesmoke. Remove sensors prior to heavy remodeling or construction.FIGURE 1. WIRING DIAGRAM:CAUTION: DO NOT LOOP WIRE C0100-01Note: Only System Sensor approved accessories may be used with the 2251BRA.FIGURE 2. ROTARY DECADE ADDRESS SWITCHES:TENS ONES98765432109876543210C0146-00TAMPER-RESISTANCEModel 2251BRA includes a tamper-resistant capability that prevents its re-moval from the bracket without the use of a tool. Refer to the base manual for details on making use of this capability.TESTINGBefore testing, notify the proper authorities that the system is undergoing maintenance, and will temporarily be out of service. Disable the system to prevent unwanted alarms.All sensors must be tested after installation and periodically thereafter. Test-ing methods must satisfy the Authority Having Jurisdiction (AHJ). Sensors offer maximum performance when tested and maintained in compliance with CAN/ULC-S536.The sensor can be tested in the following ways:A. Functional: Magnet Test (P/N M02-04-01 or M02-09-00)T his sensor can be functionally tested with a test magnet. The test mag-net electronically simulates smoke in the sensing chamber, testing the sensor electronics and connections to the control panel. 1. H old the test magnet in the magnet test area as shown in Figure 3.6581 Kitimat Road, Unit 6, Mississauga, Ontario L5N-3T51.800.SENSOR2; Fax: 905-812-0771www.systemsensor.ca2. The sensor should alarm the panel.T wo LEDs on the sensor are controlled by the panel to indicate sensor status. Coded signals, transmitted from the panel, can cause the LEDs to blink, latch on, or latch off. Refer to the control panel technical docu-mentation for sensor LED status operation and expected delay to alarm.B. Smoke EntryThe GEMINI model 501 aerosol generator can be used for smoke entry testing. Set the generator to represent 4%/ft to 5%/ft obscuration as de-scribed in the GEMINI 501 manual. Using the bowl shaped applicator, apply aerosol until the panel alarms.A dditionally, canned aerosol simulated smoke (canned smoke agent) may be used for smoke entry testing of the smoke detector. Tested and approved aerosol smoke products are:MANUFACTURER MODEL Home Safeguard Industries 25S SDi SOLOA4SDiSMOKESABRE-01When used properly, the canned smoke agent will cause the smoke detector to go into alarm. Refer to the manufacturer’s published instructions for proper use of the canned smoke agent.Canned aerosol simulated smoke (canned smoke agent) formulas will vary by manufacturer. Misuse or overuse of these products may have long term adverse effects on the smoke detector. Consult the canned smoke agent manufacturer’s published instructions for any further warnings or caution statements.C. R emote Test2251BRA can be remotely tested using the RTS451KEYA or RTS-151KEYA test accessories. Refer to the DNRA manual for wiring dia-grams. Maximum test response time may be up to two communications from the panel.A sensor that fails any of these tests should be cleaned as described under CLEANING, and retested. If the sensor fails after cleaning, it must be replaced.When testing is complete, restore the system to normal operation and notify the proper authorities that the system is back in operation.FIGURE 3. TEST MAGNET POSITION:C0145-02CLEANINGBefore removing the detector, notify the proper authorities that the smoke detector system is undergoing maintenance and will be temporarily out of service. Disable the zone or system undergoing maintenance to prevent un-wanted alarms.1. Remove the sensor to be cleaned from the system.2.R emove the sensor cover by pressing firmly on each of the four removal tabs that hold the cover in place.3. V acuum the screen carefully without removing it. If further cleaning isrequired continue with Step 4, otherwise skip to Step 7.4. R emove the chamber cover/screen assembly by pulling it straight out.5. U se a vacuum cleaner or compressed air to remove dust and debrisfrom the sensing chamber.6. R einstall the chamber cover/screen assembly by sliding the edge overthe sensing chamber. Turn until it is firmly in place.7. R eplace the cover using the LEDs to align the cover and then gentlypushing it until it locks into place.8. Reinstall the detector.9. Test the detector as described in TESTING.10. Reconnect disabled circuits.11. Notify the proper authorities that the system is back on line.FIGURE 4. SENSOR ASSEMBLY:C0215-03SPECIAL NOTE REGARDING SMOKE DETECTOR GUARDSSmoke detectors are not to be used with detector guards unless the combina-tion has been evaluated and found suitable for that purpose.SS-400-005 2 I56-3578-000©2009 System SensorSystem Sensor warrants its enclosed smoke detector to be free from defects in materials and work-manship under normal use and service for a period of three years from date of manufacture. System Sensor makes no other express warranty for this smoke detector. No agent, representative, dealer, or employee of the Company has the authority to increase or alter the obligations or limitations of this Warranty. The Company’s obligation of this Warranty shall be limited to the repair or replacement of any part of the smoke detector which is found to be defective in materials or workmanship under normal use and service during the three year period commencing with the date of manufacture. After phon-ing System Sensor’s toll free number 800-SENSOR2 (736-7672) for a Return Authorization number, send defective units postage prepaid to: System Sensor, Returns Department, RA #__________, 6581FCC STATEMENTThis device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause Harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio/TV technician for help.This Class B digital apparatus complies with Canadian ICES-003.THREE-YEAR LIMITED WARRANTYKitimat Road, Unit 6, Mississauga, Ontario L5N-3T5. Please include a note describing the malfunction and suspected cause of failure. The Company shall not be obligated to repair or replace units which are found to be defective because of damage, unreasonable use, modifications, or alterations occur-ring after the date of manufacture. In no case shall the Company be liable for any consequential or incidental damages for breach of this or any other Warranty, expressed or implied whatsoever, even if the loss or damage is caused by the Company’s negligence or fault. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state.Please refer to insert for the Limitations of Fire Alarm Systems。
电子烟产品说明书了解电子烟的组装和使用方法提供健康的吸烟替代品电子烟产品说明书：了解电子烟的组装和使用方法，提供健康的吸烟替代品一、电子烟简介电子烟是一种新型的吸烟替代品，它通过加热电子液体产生的雾气来模拟传统香烟的吸食感受，但与传统香烟相比，电子烟并不包含焦油、一氧化碳等有害物质，可减少吸烟对健康的危害。
二、电子烟的组成部分1. 电子烟主机电子烟主机是电子烟的核心部分，一般由电池模块、加热器和控制电路组成。
电池模块提供动力，加热器负责加热电子液体，控制电路用于控制加热器的温度和保护电池等。
2. 雾化器雾化器是电子烟的关键部件，它将电子液体转化为雾气，供用户吸入。
雾化器内部包含一个雾化芯，电子液体通过雾化芯的加热作用，变成可吸入的雾气。
3. 电子液体电子液体是电子烟中的主要成分，通常由丙二醇、甘油、香料和尼古丁等组成。
用户可以根据个人喜好选择不同口味和尼古丁含量的电子液体。
三、电子烟的使用方法1. 组装电子烟首先，将雾化器与电子烟主机进行连接。
通常，雾化器底部有一个螺纹接口，将其与电子烟主机上的相应螺纹接口对准，并旋转固定。
2. 加注电子液体在雾化器的侧边或底部，有一个小孔或开关，用于加注电子液体。
将电子烟主机倒置，将电子液体缓慢地滴入加液孔，并避免过量。
3. 激活电子烟按下电子烟主机上的开关按钮，进入工作状态。
在某些型号的电子烟上，需要按住按钮一段时间，直到指示灯亮起或屏幕显示相关信息。
4. 吸食电子烟将嘴唇紧贴电子烟的嘴咬器部分，并轻吸雾气。
电子烟会自动感应到吸力并开始加热电子液体，产生雾气供您吸入。
5. 注意事项（1）使用前请确保电子烟已经充电完毕，电池电量充足。
（2）请勿将电子烟与水或高温环境接触。
（3）如出现漏液或异常情况，请立即停止使用，并与售后服务联系解决。
四、电子烟的优势与注意事项1. 健康替代品相比传统香烟，电子烟不产生焦油、一氧化碳等有害物质，更加利于保护吸烟者的身体健康，也减少了二手烟对他人的危害。
