伊莱克斯冰箱维修

不少消费者发现，在冰箱长期使用过程中，箱体两侧会发热，这个问题在夏天的时候尤其显著，因此很多消费者都怀疑冰箱是否坏掉了，是否需要进行维修?冰箱真空泵发热，那么冰箱在使用过程中产生发热发热的现象到底是怎么回事呢?这个现象正常吗?接下来快益修就给大家介绍一下关于冰箱两侧发热的具体原因以及相关的解决方法，来帮助大家正确使用冰箱。

具有防露功能的双门冰箱其正面箱门四周和中梁处均设置了内藏式防露管，防露管是冷凝器中的一部分，正常散热时，防露管的温度略高于一半温度。

因此，电冰箱外壳发热不足为怪。

箱体发热,是冰箱正常工作的正常表现。

因为冰箱是通过制冷剂吸收冰箱内部热量,然后通过管路循环,将热量散发出箱体之外来实现制冷的。

要把食物的温度降下来，就要有一个温度比他低的低温源，有了这个低温源，食物的热量就会自动转移到低温源，自身温度降低。

，冰箱里有冷藏室和冷冻室，在冷藏室的背板里埋藏着制造低温源的蒸发器盘管，盘管里流淌着制冷剂，制冷剂流过蒸发器盘管气化，吸收大量的热量，使与蒸发器盘管相接触的冰箱内壁温度降低，相应的冰箱内壁就会吸收食物的热量，使其温度降低。

冰箱发热是通过蒸发器盘管已气化的制冷剂，由它携带着从食物中吸收的热量，然后把这些热量转移到冰箱外边。

，当这些热量释放掉才能实现再次冷冻制冷。

所有的使用铜管把这些气化制冷剂转移到冷冻室保温层之外，再由冰箱中的压缩机压缩转移至冰箱外壁的冷凝器释放，完成热量转移。

整个冰箱散热的过程中，食物上的热量都被冰箱制冷所吸收，所以冰箱会在压缩机的两侧有发热的现象。

两侧发热的温度高低与季节环境温度高低有很大的关系，冬季发热温度较低，夏季发热温度很高。

如果两侧一直发热，则说明压缩机始终工作不停机，如果冰箱制冷效果良好，要么是冰箱的温度调的太低所致（机械式温控器档位调的太高，应调在较低的档位处）；要么是温控器有故障造成的。

如果冰箱制冷不好，多是管路系统异常所致，应请专业人员进行检修。

由于冰箱两侧发热所以冰箱不能够靠近墙面放置，也不能在冰箱的两侧覆盖东西，这样都会阻碍冰箱两侧散热使温度升高的，，应该保持冰箱的两侧有足够的空间散热。

伊莱克斯售后服务投诉部门电话专线据悉，伊莱克斯售后服务投诉签署了包含空调、厨卫、生活电器等品类在内的为期五年的全面深度的合作协议。

国美集团总裁表示，国美和伊莱克斯售后服务投诉双方共同探索高度协同的创新合作模式，在消费者需求信息共享、产品研发、营销推广、销售管理、售后服务等方面深度合作。

代表着健康生活的世界品牌，伊莱克斯售后服务投诉知道仅仅限于“维修”的售后服务，已经不能够满足用户的心理。

顾客购买产品意味着对其公司文化的认可和信任，因此，不管是销售时还是售后服务中，企业都要以诚信的态度对待所有的消费者。

伊莱克斯售后服务投诉率先在家电行业引入人性化服务，超越了简单的售后维修概念，遍布全国600多个服务网点完善的本地化服务，高效的服务网络，给消费者带来专业标准的服务。

伊莱克斯售后服务投诉家电产品自进入中国以来，以零缺陷的产品和服务，不断满足广大消费者对享受舒适生活的向往和追求！正如我们倡导的———为顾客带来不断创新的解决方案、生活享受和自豪感。

伊莱克斯售后服务投诉对每一项售后服务内容，伊莱克斯都会以书面的形式对客户承诺，让客户真正地放心并满意，而伊莱克斯售后服务投诉遍布全国95%以上销售区域的300多家专业客户服务中心，不仅辐射广、管理完善，更与很多销售服务合一的维修点不同，伊莱克斯售后服务投诉完全不带有赢利性质，这是兑现所有承诺的有效保障。

伊莱克斯售后服务投诉为使用户得到满意的服务，伊莱克斯售后服务投诉所有网点的服务质量都会接受用户监督，伊莱克斯总公司开通的客户投诉热线，保证每个服务诉求电话有问必答，每封服务要求信函来函必复，伊莱克斯售后服务投诉让每一位客户的投诉都能得到详细、准确的记录，并在第一时间得到解决。

将冰箱放置到阴凉的位置。

对其进行定期检查。

采用新方法冷冻食物。

这些小窍门可提高冰箱的能效。

【伊莱克斯售后服务投诉部门提醒注意事项】考虑应将冰箱放置在何处：•将器具放置在阴凉的位置可节约大量的能源-避免将其放置在热源（如烘烤箱、取暖器或阳光直射点）周围•考虑在您的冰箱与墙壁和地板的热源之间采取隔热措施。

电力蒸汽对衡式锔炉l 操作说明书air-o-steamer 1使用操作总体说明在打开设备使用前,请仔细阅读本使用手册。

本手册对设备的具体使用进行了详细的描述和说明。

如果您想了解更多关于本产品的一些其他信息，请联络您当地的产品销售代理商。

? 请勿在设备顶盖上放置烤盘或烹饪器具，以免阻碍设备排气排烟。

? 定期地（每年至少一次）对设备进行检查和维护。

因此，我们建议用户能与专业的售后服务维修商签订一份维护保养协议。

? 肉针温度探头是很精密的仪器，因此在使用时要特别小心。

不要用它敲击东西，插入食物内时也不要用力过猛；拔出时，也不要硬拉肉针顶部（在使用手推车烤架时要尤其小心）如果肉针探头因操作不正确而损坏，不在保修范围内。

? 在使用混合烹饪程序时，注意温度不要超过200℃-210℃。

在使用此烹饪程序时，温度过高，烤箱密封条的密封性能将会有所减弱。

? 当放入烤盘时，两个烤盘间最好至少相隔40mm，以便促进烤箱内空气对流。

* 特别是选择使用带蒸汽的烹饪程序烤制食物时，切勿在烤箱内向食物洒盐， * 不要烤带酒精的食物。

attn：如果按说明正确安装万能蒸烤箱且选用我们原装烤盘的，能放入烤箱内最高的烤盘也只能在1.6m；如果您购买的附件不是原装的烤盘，那么注意在放入烤盘时，千万不要超过以上规定的高度。

由于在烹饪时，烤盘内的液态物，如：酱汁、油、被熔化的脂肪等，可能会溅出烤盘外。

如果高于这个高度，那么放在最高的烤盘内食物的烹饪情况，操作人员就无法看到了。

1．开门我们万能蒸烤箱的门锁带有安全设计装置，以免操作人员在打开烤箱门时被大量涌出的蒸汽灼伤。

根据不同型号，请选择以下相应的步骤操作：1.1 6格和10格的烤箱重要！当心灼伤！烤箱内热时，务必小心开门！a. 将门把手随意向哪个方向拉到底。

由于安全装置的作用，此时的门只被打开一条缝。

如果此时正在进行烹饪的话，烹饪程序将被打断。

2 b．松开门把手，然后重复以上“a”的操作步骤，把门完全打开。

伊莱克斯ZBM1680/1880KPA系列冰箱维修手册目录一、产品外观结构特征图二、产品部件结构名称三、技术参数四、箱内基本配置五、制冷系统原理图六、电气原理图七、内部结构管路实物图八、零部件拆卸方法九、压缩机技术参数（HYE81MGU 220-240V ～50Hz LBP）十、总装分解图十一、接线图一、产品外观结构特征图二、产品部件结构名称三、技术参数四、箱内基本配置五、制冷系统原理图双门机械温控式制冷系统制冷剂走向流程图六、电气系统原理图七、内部结构管路实物图八、零部件拆卸方法1、门开关的拆卸ａ、用平口起撬起灯开关 b、拔下连接插头，拆下灯开关2、照明灯的拆卸九、压缩机技术参数（HYE81MGU 220-240V ～50Hz LBP）使用条件：制冷剂标准性能:制冷量…………………………………………≥140W×95%输入功率………………………………………≤90W×115%COP……………………………………………≥1.55W/W×95% 电流……………………………………………≤0.47A×110% 电机参数:电机保护器………………………………….. 外置式保护器电压范围…………………………………….. 187-254V主绕组阻值……………………………………26.3Ω±10%副绕组阻值……………………………………25.8Ω±10%电器部件:过载保护器型号…………………………………………… B40-105/B动作电流…………………………………….. ..4.0A动作温度…………………………………….. 105±5℃恢复温度…………………………………….. 61±9℃阻燃等级…………………………………….. UL94V-0PTC启动器型号………………………………………….. QP2-12/B3电阻（25℃）……………………………….. 9-18Ω最大工作电压 (350V)最大工作电流……………………………….. 8A冷冻油充灌：油类型…………………………………矿物油充灌量…………………………………200±10ml极限工况:环境温度范围………………………… 0～43℃蒸发温度范围………………………… -35～-15℃最高绕组温度………………………… 130℃最高壳温……………………………… 95℃最高排气温度………………………… 110℃启动性能………………………………187V（0.3Mpa平衡压力）残留物：压缩机内的含水量≤100mg整机杂质含量≤50mg干燥空气正压注意事项：1.拔下压缩机橡胶管塞后，应在5分钟内将其迅速装入制冷系统中，（建议先拔工艺管塞）。

伊莱克斯维修收费标准
伊莱克斯是一家专业的家电维修服务公司，我们致力于为客户提供高质量、高效率的维修服务。

为了让客户更加了解我们的服务收费标准，我们特地整理了以下的收费标准，希望能够为您提供参考。

一、上门维修收费标准。

1. 故障诊断费，100元/次。

如果客户同意维修，故障诊断费将会在最终的维修费用中得到抵扣。

2. 维修人工费，根据不同的维修项目和维修难度而定，具体费用请咨询我们的客服人员。

3. 配件更换费，如果需要更换配件，将会根据配件的类型和价格进行收费，具体费用请咨询我们的客服人员。

二、维修保养套餐收费标准。

1. 清洗保养套餐，150元/次。

包括清洗内部灰尘、更换滤网等内容。

2. 全面保养套餐，300元/次。

包括清洗内部灰尘、更换滤网、检查电路及部件状况等内容。

三、注意事项。

1. 维修费用均为人工费和配件费的总和，不包括上门费和其他杂费。

2. 在维修过程中，如需更换配件，我们将会提前告知客户，并征得客户的同意后进行更换。

3. 维修完成后，我们将会对维修过的设备进行测试，确保设备正常运行后再收取维修费用。

四、收费说明。

1. 维修费用均为现金结算，不接受信用卡、支付宝等电子支付方式。

2. 维修费用不包括增值税，如有增值税发票需求，请提前告知我们的客服人员。

以上就是伊莱克斯维修收费标准，我们会根据实际情况对收费标准进行调整，
具体收费以维修人员出具的维修清单为准。

希望以上内容能够帮助客户更好地了解我们的服务收费标准，如有任何疑问或需要进一步了解，请随时联系我们的客服人员，我们将竭诚为您服务。

© Copyright 2006 ELECTROLUX HOME PRODUCTS PTY LTD Technical ServicesELECTROLUX HOME PRODUCTS PTY LTDABN 51 004 762 341ELECTROLUX(KELVINATOR)MANUALLY CONTROLLED“J” SERIESTOP MOUNTREFRIGERATORSMODELSN280J (White) N300J (White) N330J (White) N360J (White) N390J (White)N390SJ (Stainless Steel) N420J (White) N440J (White)N440SJ (Stainless Steel) N520J (White)N520SJ (Stainless Steel)WEB SITE ADDRESS: .auFrom S/Nº 42455916On Models N280J, N300J &N330J deletion of the Pre Cooler Assy.INDEXSECTION PAGE Nº Index 2Specifications 3 - 5The Parts of The Refrigeration 6Performance Parameters 7 - 8Removal and Replacement of Door Handles 9Removal of Light Lens & Rear Control Housing 10 - 13 Removal of Top Control Housing 14 - 15 Removal of Deodoriser Cover 16How to Move the Front Half Shelf under the Rear Half Shelf 17Removal of Split Shelving 18Removal of Crisper Cover 19Adjustment of the Deli Bin 20To Disassemble the Support Frame & Deli Bin 21Adjustment of the Snugger 22Removal and Replacement of Evaporator Cover 23Removal and Replacement of Gaskets 24 - 25 Access to Pre cooler and Defrost tray 25Installation 26 - 29 Air Flow 30Refrigeration Diagram 31Refrigeration Diagram Models N280J, N300J, N330J32from S/Nº 42455916Circuit/Wiring Diagrams 33 - 37Page 2 RESI108SPECIFICATIONSDESCRIPTION N280J N300J N330J DIMENSIONSHeight (mm) 1550 1620 1720Width (mm) 607 607 607Depth (mm) 681 681 681Total Capacity (Litres) 286 303.1 328.4COMPRESSOR PART Nº Embraco1442389Embraco1442389Embraco1442389Type ECR 55 HLP ECR 55 HLP ECR 55 HLP Run Winding (ohms) 14.8 14.8 14.8 Start Winding (ohms) 17.2 17.2 17.2 Run Amps 0.49 0.49 0.49 Starting Amps 8.5 8.5 8.5Oil Charge (cc) 280 280 280CONTROL PART Nº Daesung1444849Daesung1444849Daesung1444849TypeMidCut-in (ºC) 6.5+/-1.2 6.5+/-1.2 6.5+/-1.2 Cut-out (ºC) 2.5+/-1.2 2.5+/-1.2 2.5+/-1.2 MANUAL BAFFLEPART Nº 144119514411951441195 DEFROST TIMER PART NºType 8 Hour / 5 mins drip143982114398211439821D.T.T. PART NºTypeCut-In (ºC)Cut-Out (ºC) 1442102Inchang0.0+/-2.511+/-2.51442102Inchang0.0+/-2.511+/-2.51442102Inchang0.0+/-2.511+/-2.5THERMAL FUSE PART Nº 1442642 1442642 1442642HEATER DEFROST PART Nº 1440999 1440999 1440999 (watts) 325 325 325 (ohms) 177 177 177FAN MOTOR PART Nº Shinhan Tech1444850Shinhan Tech1444850Shinhan Tech1444850FAN BLADE PART Nº 1435563 1435563 1435563INTERIOR LAMP FC PART Nº 1442001 1442001 1442001 Type 25w E14SES Blue 25w E14SES Blue 25w E14SES BlueCAPACITOR RUN PART Nº Rating14367154uf - 400v14367154uf - 400v14367154uf - 400vREFRIGERANTType R134a R134a R134aCharge (grams) 100 100 100Page 3 RESI108SPECIFICATIONSDESCRIPTION N360J N390J/SJ N420J DIMENSIONSHeight (mm) 1640 1720 1640Width (mm) 702 702 702Depth (mm) 681 681 743Total Capacity (Litres) 367.8 392.5 415.6COMPRESSOR PART Nº Electrolux1442337Electrolux1442337Electrolux1442337Type GVT 66 AA GVT 66 AA GVT 66 AA Run Winding (ohms) 15.9 15.9 15.9 Start Winding (ohms) 16.5 16.5 16.5 Run Amps 0.56 0.56 0.56 Starting Amps 8.5 8.5 8.5Oil Charge (cc) 230 230 230CONTROL PART Nº Daesung1446274Daesung1446274Daesung1446274TypeMidCut-in (ºC) 5.5+/-1.2 5.5+/-1.2 5.5+/-1.2 Cut-out (ºC) 1.5+/-1.2 1.5+/-1.2 1.5+/-1.2 MANUAL BAFFLEPART Nº 144119514411951441195 DEFROST TIMER PART NºType 8 Hour / 5 mins drip1439821 1439821 1439821D.T.T. PART NºTypeCut-In (ºC)Cut-Out (ºC) 1442102Inchang0.0+/-2.511+/-2.51442102Inchang0.0+/-2.511+/-2.51442102Inchang0.0+/-2.511+/-2.5THERMAL FUSE PART Nº 1442642 1442642 1442642HEATER DEFROST PART Nº 1441000 1441000 1441000 (watts) 350 350 350 (ohms) 165 165 165FAN MOTOR PART Nº Shinhan Tech1444850Shinhan Tech1444850Shinhan Tech1444850FAN BLADE PART Nº 1435563 1435563 1435563INTERIOR LAMP FC PART Nº 144200114420011442001 Type 25w E14SES Blue 25w E14SES Blue 25w E14SES BlueCAPACITOR RUN PART Nº Rating14367154uf – 400v14367154uf – 400v14367154uf – 400vREFRIGERANTType R134a R134a R134a Charge (grams) 110 110 110Page 4 RESI108SPECIFICATIONSDESCRIPTION N440J/SJ N520J/SJDIMENSIONSHeight (mm) 1720 1720Width (mm) 702 802Depth (mm) 743 743Total Capacity (Litres) 441.5 517.1COMPRESSOR PART Nº Electrolux1442337Electrolux1442336Type GVT 66 AA GVT 75 AA Run Winding (ohms) 15.9 14.9 Start Winding (ohms) 16.5 16.7 Run Amps 0.56 0.67 Starting Amps 8.5 9.92Oil Charge (cc) 230 230CONTROL PART Nº Daesung1446274Daesung1446274TypeMidCut-in (ºC) 5.5+/-1.2 5.5+/-1.2 Cut-out (ºC) 1.5+/-1.2 1.5+/-1.2 MANUAL BAFFLEPART Nº 14411951441195 DEFROST TIMER PART NºType 8 Hour / 5 mins drip1439821 1439821D.T.T. PART NºTypeCut-In (ºC)Cut-Out (ºC) 1442102Inchang0.0+/-2.511+/-2.51442102Inchang0.0+/-2.511+/-2.5THERMAL FUSE PART Nº 1442642 1442642HEATER DEFROST PART Nº 14410001441001 (watts) 350 375(ohms) 165154FAN MOTOR PART Nº Shinhan Tech1444850Shinhan Tech1444850FAN BLADE PART Nº 1435563 1435563INTERIOR LAMP PART Nº 1442001 1442001 Type 25w E14SES Blue 25w E14SES BlueCAPACITOR RUN PART Nº Rating14367154uf – 400v14367154uf – 400vREFRIGERANTType R134a R134aCharge (grams) 110 130Page 5 RESI108Page 6 RESI108THE PARTS OF THE REFRIGERATORPERFORMANCE PARAMETERS (MANUAL REFRIGERATORS)These parameters are guideline for service personnel only.STORAGE TEMPERATURESThe following table is a guideline for temperatures and run times expected for standard top mount Electrolux/Kelvinator J Series product operating in climate temperatures of approximately 20 to 30°C set on MID freezer and MID refrigerator settings:Freezer -19°C to –16°CFood 2°C to 4°C30°C Run Time ~50% Doors closed20°C Run Time ~35% Doors closedThe product is fitted with a thermostat as the refrigerator compartment control and a baffle as the freezer control.Setting the refrigerator control (the thermostat) colder or warmer will set BOTH the freezer and the refrigerator colder or warmer. The thermostat is designed to provide refrigerator compartment temperatures of –2 to 1°C on coldest, and 5 to 8°C on warmest, depending on the altitude and climate that the product is operating in.Setting the freezer control (the baffle) colder or warmer will set ONLY the freezer colder or warmer. One notch movement of the baffle will adjust the freezer temperature by approximately 1°C.The storage temperature in each product will vary depending on the climatic temperature, the altitude, and the usage pattern of each customer. MID freezer and MID food compartment settings are the best starting settings but customers should adjust gradually to suit their storage temperature preference, the climate that they live in, the altitude they live at and how theyuse the product.Why does climatic temperature variance affect storage temperature?For the basic customer requirement of preserving food safely an electromechanical thermostat and baffle system is ideal. When the climatic temperature gets very hot or very cold then the customer may need to adjust the baffle to maintain their preferred storage temperatures. This is because as the climate gets very cold then there is only minor cooling required to keep the refrigerated section of the product cold. Because the thermostat is best located in the refrigerator section then the freezer tends to warm up. This can be overcome by setting the freezer colder, which directs more air to the freezer section when the fan and compressor come on.Likewise when the climate temperature gets very hot the refrigerator section will be running for longer periods and overcoming lots of door openings as customers refresh in the hot weather. The freezer will tend to run colder in these conditions so it can help to save energy and give the refrigerator more capacity to recover from the higher usage if the freezer is set warmer.Page 7 RESI108Why does altitude variance affect storage temperature slightly?Thermostats consist of an expanding/contracting vessel filled with refrigerant. As the refrigerant warms up it expands and completes an electrical circuit which turns the fridge on. As altitude increases, that is we get higher above sea level, then atmospheric pressure decreases. That means that the vessel has to heat up a little less to complete the electrical circuit. The net result is that a product operating approximately 1000m above sea level will operate approximately 1-2°C colder than it would at sea level. The product should be set slightly warmer in these regions to compensate.THERMOSTAT OPERATIONThe cut out and cut in temperatures of the thermostat at sea level are:1446274Coldest Mid WarmestCut In 1.5 ± 2.0 5.5 ± 1.2 9.5 ± 2.0Cut Out -2.5 ± 2.0 1.5 ± 1.2 5.5 ± 2.01444849Coldest Mid WarmestCut In 3.0 ± 2.0 6.5 ± 1.2 10.5 ± 2.0Cut Out -1.5 ± 2.0 2.5 ± 1.2 6.5 ± 2.0Note that the thermostat has a rotation of 305°. These figures are for the thermostat as fitted to the control housing for which only 180° adjustment is available.DEFROST SYSTEMGeneral defrost system parameters:Time Between Defrosts - 8 Hours Compressor On TimeHeater on Time - VariableDry Defrost - Expect 8 to 12 minutes heater on timeHigh Usage Tropical Climate - Expect up to 30 minutes heater on timeDrip Time After Defrost before- 5 minutesCompressor Start upDefrost Termination Thermostat - Bi-Metal- Cut In 0°C, Cut Out +11°CThermal Fuse - +72°C Blown Cut OutWhy does the freezer sometimes hiss, is gas leaking?To achieve the frost free cooling environment moisture and ice need to be removed from the product. Depending on usage and climate the product will “defrost” the cooling system which is located in an insulated compartment at the back of the freezer. The hissing sound is not a gas leak but water dripping onto the heating element used to melt and remove the ice. These generally happen approximately once a day for 20 minutes and insulated and shielded so food storage quality is not compromised during this period.Page 8 RESI108Page 9 RESI108REMOVAL OF DOOR HANDLESPage 10 RESI108REMOVAL OF THE LIGHT LENS AND REAR CONTROL HOUSINGGives access to the Lamp, Thermostat & Manual Baffle.Remove the knobs.To access the manual damper, either remove the gasket, or slit it at the points indicated by the arrows. The insulation block can then be hinged back to access the damper. When re assembling,the gasket must be replaced or resealed at the slits.REMOVAL OF THE TOP CONTROL HOUSING Gives access to the Defrost Timer.Remove the Rear Control Housing first.REMOVAL OF THE DEODORISER COVERTO SLIDE THE FRONT SHELF UNDER THE REAR SHELFREMOVAL OF THE FRONT SHELF FROM THE ASSEMBLYREMOVAL OF THE CRISPER COVERADJUSTMENT OF THE DELI BINIt is possible to slide the Deli Bin from side to side. Two slides (LH & RH) control the air flow to the bin.TO DISASSEMBLE THE SUPPORT FRAME & DELI BINADJUSTMENT OF THE SNUGGERTO REMOVE/REPLACE EVAPORATOR COVER(Gives access to Fan Motor/Blade, Evaporator, Defrost Heater, Thermal Fuse, Defrost Termination Thermostat & Drain Trough)To remove the evaporator cover, use a hooked tool similar to the one in the drawing belowTwo plug buttons covering the screws can be removed with a flat bladed screwdriverCarefully warming up the evaporator cover with a hair dryer will make it pliable for removal. Place the hooked tool pointing downwards into the bottom corners of the louvres (as indicatedby the arrows). Pull on the tool until the clips on the rear of the cover disengage to the extentthat the cover is removable by hand.To refit, position the evaporator cover into the rear of the freezer and push firmly to lock theclips into place.TO REMOVE/REPLACE DOOR GASKETSTo remove the door gasket, start in one of the corners and pull perpendicular to the inner door panel. Once it is released from the corner it can then be peeled off the remainder of the door.To fit a gasket, start by pressing it into the corners first.With the gasket fitted into the corners, move around the door pressing the gasket into the inner panel groove using your thumbs.TO ACCESS THE PRE COOLER AND DEFROST TRAYTilt the refrigerator backwards and support. The pre cooler and defrost tray should be visible on the underside of the cabinet. Unclip the three clips on the LH and RH pre cooler brackets. Easethe pre cooler downwards to access both the pre cooler and defrost tray.INSTALLATIONCLEARANCES AROUND THE REFRIGERATOR Recommended minimum clearances are :• 3cm on each side.• 9cm above the refrigerator.• 5cm behind the refrigerator.The refrigerator should arrive with the front adjustable rollers wound down to tilt the top of the refrigerator backwards by about 10-15mm from the upright. The stability foot should also be wound fully up so it will not interfere with the operation of the rollers.WARNING: The rollers are designed for forward and backward movement only. They are not castors. Moving the refrigerator sideways may cause damage to the floor and rollers.• Roll the refrigerator into its final position.• The top of the refrigerator should be tilted back by approximately 10-15mm. This will allow the doors to self-close providing a consistent door seal. It is normal for the freezer door tomomentarily open and reclose when the food compartment door is closed firmly. If the freezer door stays open you will need to tilt the refrigerator backwards a little further.• If the refrigerator is not tilted back, you can adjust the two front rollers by turning the large plastic roller nut. This will increase the height of the rollers. One turn of the nut will tilt the refrigerator back approximately 10mm. If you have difficulty turning the roller nut you can have someone tilt the refrigerator back, so that you have better access. Alternatively, you can access the rollers from the side, using a flat screwdriver to help you turn the nut.• If the refrigerator now rocks from one corner to the opposite rear corner, this means that the flooris uneven, you will need to put some packing under one of the rear rollers. You could use thin pieces of solid material, such as thin board, vinyl floor tiles or laminate. Place the packing so that it will sit under one of the rear rollers when the refrigerator is rolled into position.• Check the alignment of the refrigerator to the surrounding cupboards. The top of the refrigeratorshould be level from side to side. If you need to adjust the level, use the adjustable rollers.When you have the refrigerator in its final position wind the stabilising foot down until it just makes contact with the floor. When you need to move the refrigerator, be sure to wind the foot back up so that the refrigerator can roll freely.Stabilising foot wound down.AIRFLOW DIAGRAMREFRIGERATION DIAGRAMREFRIGERATION DIAGRAMFor Models N280J, N300J, & N330J from Serial Number 42455916WARNINGIT IS ILLEGAL FOR PERSONS OTHER THAN LICENSED ELECTRICAL MECHANICS OR PERSONS AUTHORISED BY LEGISLATION TO WORK ON THE FIXED WIRING OF ANY ELECTRICAL INSTALLATION. PENALTIES FOR CONVICTION ARE SEVERE.IMPORTANT SAFETY NOTICEThis diagram has been prepared for use by electrically qualified service technicians. The manufacturer cannot be held responsible for the interpretation of its service publications nor for any injury or damage that may occur in connection with their use.WARNINGPERSONS OTHER THAN LICENSED ELECTRICAL MECHANICS OR PERSONS AUTHORISED LEGISLATION TO WORK ON THE FIXED WIRING OF ANY ELECTRICAL INSTALLATION. PENALTIES FOR CONVICTIONIMPORTANT SAFETY NOTICEThis diagram has been prepared for use by electrically qualified service technicians. The manufacturer cannot be held responsible for the interpretation of its service publications nor for any injury or damage that may occur in connectionWARNINGIT IS ILLEGAL FOR PERSONS OTHER THAN LICENSED ELECTRICAL MECHANICS OR PERSONS AUTHORISED BY LEGISLATION TO WORK ON THE FIXED WIRING OF ANY ELECTRICAL INSTALLATION. PENALTIES FOR CONVICTION ARE SEVERE.IMPORTANT SAFETY NOTICEThis diagram has been prepared for use by electrically qualified service technicians. The manufacturer cannot be held responsible for the interpretation of its service publications nor for any injury or damage that may occur in connection with their use.WARNINGPERSONS OTHER THAN LICENSED ELECTRICAL MECHANICS OR PERSONS LEGISLATION TO WORK ON THE FIXED WIRING OF ANY ELECTRICAL INSTALLATION. PENALTIES FOR CONVICTIONIMPORTANT SAFETY NOTICEThis diagram has been prepared for use by electrically qualified service technicians. The manufacturer cannot be held responsible for the interpretation of its service publications nor for any injury or damage that may occur in connectionWARNINGIT IS ILLEGAL FOR PERSONS OTHER THAN LICENSED ELECTRICAL MECHANICS OR PERSONS AUTHORISED BY LEGISLATION TO WORK ON THE FIXED WIRING OF ANY ELECTRICAL INSTALLATION. PENALTIES FOR CONVICTION ARE SEVERE.IMPORTANT SAFETY NOTICEThis diagram has been prepared for use by electrically qualified service technicians. The manufacturer cannot be held responsible for the interpretation of its service publications nor for any injury or damage that may occur in connection with their use.。

伊莱克斯维修收费标准伊莱克斯维修服务是一家专业的家电维修公司，为广大用户提供优质的维修服务。

为了更好地服务用户，我们特制定了以下的维修收费标准，以便用户了解我们的收费情况，确保维修过程的透明和公正。

一、上门维修收费标准。

1. 上门维修基本费用，100元/次。

包含上门服务费、上门维修师傅的工时费用。

2. 配件更换费用，根据具体配件种类和数量进行收费，具体收费标准请咨询客服人员或上门维修师傅。

3. 临时维修费用，若需要在维修过程中进行临时维修或紧急处理，将会根据实际情况进行收费，具体费用请与维修师傅商议。

二、送修维修收费标准。

1. 送修维修基本费用，50元/次。

包含送修服务费、维修师傅的工时费用。

2. 配件更换费用，根据具体配件种类和数量进行收费，具体收费标准请咨询客服人员或维修师傅。

3. 临时维修费用，若需要在维修过程中进行临时维修或紧急处理，将会根据实际情况进行收费，具体费用请与维修师傅商议。

三、维修服务保障。

1. 我们提供的所有维修服务均享有30天的免费保修期，若在保修期内出现同一故障，我们将免费为您进行二次维修。

2. 对于更换的配件，我们提供90天的质保期，若在质保期内出现问题，我们将免费更换或进行修理。

四、收费说明。

1. 收费标准为参考标准，具体收费以实际维修情况为准，具体收费情况请与维修师傅或客服人员进行确认。

2. 维修过程中若需要更换配件，我们将提供配件的发票，保证配件的真实性和质量。

3. 维修完成后，我们将提供详细的维修报告和收费清单，确保收费的透明和合理。

以上即是我们伊莱克斯维修的收费标准，我们将秉承着诚实、公正、透明的原则，为用户提供最优质的维修服务。

感谢您选择伊莱克斯维修，我们将竭诚为您服务。

电冰箱的维修方法与技巧冰箱是我们生活中经常都会使用到的，但是有时候电冰箱坏了需要修理的话，应该要掌握好哪些的修理方法与技巧吗，下面为大家精心整理了一些关于电冰箱的维修方法与技巧，希望对你有所帮助，欢迎查阅。

电冰箱的维修方法与技巧一、询问检查法询问检查法是检修电冰箱控制系统最基本的方法。

实际上，该方法也最容易被初学者和维修人员忽略。

他们接到故障机后不向用户进行耐心地询问，未辨别出是真故障，还是假故障，就开始大刀阔斧地进行拆卸，有时不仅不能快速排除故障，还容易扩大故障。

这样，不仅浪费了时间，还有损个人和维修部门的声誉。

因此，维修前，仔细询问用户，该机是否维修过、故障特征、故障是如何形成的是很重要的，对于许多故障的检修可事半功倍。

比如，在检修压缩机不停机故障时，若用户讲电冰箱的制冷效果差，则说明故障是由于制冷系统发生泄露或压缩机异常引起的;若温度过低如冷藏室结冰，说明故障是由于温控器的触点不能断开所致。

二、直观检查法直观检查法是检修电冰箱的最基本方法。

它是通过一看、二听、三摸、四闻来判断故障部位的检修方法，维修中可通过该方法对故障部位进行初步判断。

1.看看就是通过观察来发现故障部位和故障原因的检修方法。

下面根据查看不同部位的特征，进行故障部位判断。

检修照明灯不亮故障时，可先查看照明灯的灯丝是否烧断，若烧断，说明照明灯损坏。

检修压缩机不启动故障时，查看启动器、过载保护器是否脱落、破损，若是，说明它们损坏。

当压缩机运转正常时，蒸发器表面无霜、结霜不实或结霜不均匀，说明制冷系统工作异常。

直冷式双门电冰箱的冷藏室蒸发器总是结满霜，而不是化霜、结霜交替变化，应查看门封条是否正常，若门封条正常，多为温控器异常。

若间冷式电冰箱制冷不正常，查看风扇的扇叶是否被冰冻住，若是，说明自动化霜电路异常。

若冷冻室不是结霜，而是结冰，说明压缩机运转时间过长，应查温控器。

为电冰箱加注制冷剂后，若发现回气管结霜，说明加注的制冷剂过多。

冰箱常见故障和维修方法引言冰箱是我们日常生活中不可或缺的家电之一，然而它也可能会出现常见故障。

本文将介绍一些冰箱常见故障，并提供相应的维修方法，以帮助您解决冰箱问题。

1. 冰箱温度过高或过低1.1 温度过高如果冰箱内部温度过高，可能是由以下原因导致： - 冰箱门密封不良：检查冰箱门的密封条是否完好，如有破损可更换密封条。

- 冰箱背后灰尘堆积：清理冰箱背后的灰尘，确保排热散热器正常工作。

- 温度设置不正确：检查冰箱温度设置，确保正确设置。

- 冰箱散热器故障：如果排热散热器损坏或堵塞，需要更换或清理。

1.2 温度过低如果冰箱内部温度过低，可能是由以下原因导致： - 温度设置过低：适当调高冰箱温度设置，确保温度在适宜范围内。

- 冰箱传感器故障：检查冰箱传感器是否正常工作，如有故障需要更换。

- 冰箱压缩机故障：如果冰箱内部温度过低且常开状态，可能是冰箱压缩机故障，需要找专业维修人员维修。

2. 冰箱制冷效果差2.1 制冷效果变差如果冰箱制冷效果变差，可能是由以下原因导致： - 冰箱门不严密：检查冰箱门的密封是否完好，如有破损可更换密封条。

- 冰箱制冷系统漏氟：如果冰箱制冷系统漏氟，需要请专业人员进行制冷剂补充和系统维修。

- 冰箱后部热交换器故障：如果冰箱后部热交换器故障，需要找专业维修人员检修。

2.2 冰箱制冷效果完全失效如果冰箱制冷效果完全失效，可能是由以下原因导致： - 冰箱压缩机故障：如果冰箱内部温度升高并且压缩机不运作，可能是压缩机故障，需要找专业维修人员维修。

- 冰箱电源问题：检查冰箱插座是否正常供电，可以尝试重新插拔电源插头。

- 冰箱控制电路故障：如果冰箱控制电路故障，需要找专业维修人员维修。

3. 冰箱噪音过大如果冰箱噪音过大，可能是由以下原因导致： - 冰箱放置不平稳：调整冰箱四个脚底的高度，使其平稳放置。

- 冰箱压缩机故障：如果冰箱噪音过大且持续存在，可能是压缩机故障，需要找专业维修人员进行维修。

现在人们的生活水平提高了，对于电冰箱的响动大家都是知道的，我们一般在使用冰箱的时候会听到冰箱发出“嘶嘶”或者是“咕噜”这样的流水声，其实这些都是正常的。

电冰箱相应的制冷系统里面会有一些制冷剂，他在正常工作的时候就会出现流动声音，相反的如果没有这样的声音，倒是电冰箱不正常的情况了。

伊莱克斯冰箱维修之漏电问题对于伊莱克斯冰箱维修当中漏点问题是一个相对较为普遍的情况，那么一旦出现这样的情况我们该怎样检查呢?二、处理方法1、我们可以通过检查把一些绝缘不好的零部件全都更换成绝缘好的新零件。

2、对于冰箱的温控器出现漏电的时候，我们需要把它的外客进行接地处理。

3、对于冰箱的启动继电器出现漏电的现象，我们可以使用纱布然后沾上一种四氟化碳的物质进行擦干净，然后利用电风扇进行吹干处理。

4、对于电机接线柱的外壳出现漏电的情况，我们可以使用四氟化碳来进行擦干净。

当然也可以把相应的电机卸下，然后放到温箱里面，然后在80-100℃下进行烘烤2小时的处理。

环境温度低于16度，需要打开低温补偿开关，打开不加热，按机械冰柜不启动中的检测方法检查加热丝和磁敏温度开关，加热丝和磁敏温度开关正常但无电压输入，可判定是主控板故障或线路故障。

低于3度甚至0度，请咨询用户提高环境温度。

检查食品是否放置过多，特别是卧式冷柜不要超过食品线。

产品不要直晒，通风要良好，散热后背与侧板要与墙壁保持10公分以上距离。

除霜问题对于人工除霜冰柜，检查冰柜是不是长时间没有除霜，造成霜层过厚，导致冷热无法交换，影响冰柜制冷，对于自动除霜冰柜，打开蒸发器盖板，检查蒸发器是否有很厚的霜层，如果没有，按冰柜不制冷流程分析，如果结很厚的霜，检查化霜加热丝电阻是否正常，一般500欧姆左右。

断路说明加热丝损坏。

检查限温器，如果断开则说明限温器损坏，检测化霜传感器是否正常。

限温器固定在翅片蒸发器上，外部为一透明塑料罩。

限温器为不可恢复部件，断开后即损坏必须更换。

开门检查或传感器故障咨询用户是否开门频繁，是否放置食品过多导致门体无法关严，咨询用户正确使用，并检查门封是否闪缝，门封压合面积(压合宽度要超过6mm)是否足够。

伊莱克斯ZSE4392ZGA冰箱显示“Fd”代码故障检修
张生定
【期刊名称】《家电维修》
【年(卷),期】2022()4
【摘要】一台伊莱克斯ZSE4392ZGA对开门冰箱,通电几秒后显示代码“Fd”,压缩机不启动,冰箱不制冷。

分析检修:查阅该机资料,没有找到故障代码“Fd”的含义。

拆机检查,发现主板(板号为17-08301-00B)上插座CN2外接冷藏、冷冻室的温度
传感器,其连接关系如图1所示。

【总页数】1页(PV0025)
【作者】张生定
【作者单位】不详
【正文语种】中文
【中图分类】F42
【相关文献】
1.格力变频空调显示H5代码故障检修
2.Galanz(L1)电磁炉显示E0代码故障检修
3.海尔RPC450MXSKYA变频多联机频繁显示代码“37-2”故障检修
4.商用冰柜
面板显示“Err”代码故障检修5.美的MG80-1213EDS型滚筒洗衣机面板显示
E30代码故障检修
因版权原因，仅展示原文概要，查看原文内容请购买。

伊莱克斯故障代码大全伊莱克斯故障代码大全是指伊莱克斯系统中可能出现的各种故障代码及其对应的解决方法。

在实际的使用过程中，由于各种原因，伊莱克斯系统可能会出现各种故障，而及时准确地识别和解决这些故障对于保证系统的正常运行至关重要。

因此，掌握伊莱克斯系统的故障代码大全及其解决方法，对于系统的维护和保养具有重要的意义。

1. 通用故障代码。

1.1 E1 故障代码，这个代码通常表示系统的电源出现了问题，可能是电源线路故障或者是电源模块故障。

解决方法，首先检查电源线路是否正常连接，然后检查电源模块是否损坏，及时更换损坏的电源模块。

1.2 E2 故障代码，这个代码通常表示系统的电机出现了问题，可能是电机本身故障或者是电机驱动器故障。

解决方法，首先检查电机是否正常工作，然后检查电机驱动器是否损坏，及时更换损坏的电机驱动器。

1.3 E3 故障代码，这个代码通常表示系统的传感器出现了问题，可能是传感器本身故障或者是传感器连接线路故障。

解决方法，首先检查传感器是否正常工作，然后检查传感器连接线路是否正常，及时更换损坏的传感器或者连接线路。

2. 空调系统故障代码。

2.1 E4 故障代码，这个代码通常表示空调系统的压缩机出现了问题，可能是压缩机本身故障或者是压缩机控制器故障。

解决方法，首先检查压缩机是否正常工作，然后检查压缩机控制器是否损坏，及时更换损坏的压缩机或者压缩机控制器。

2.2 E5 故障代码，这个代码通常表示空调系统的冷凝器出现了问题，可能是冷凝器本身故障或者是冷凝器控制器故障。

解决方法，首先检查冷凝器是否正常工作，然后检查冷凝器控制器是否损坏，及时更换损坏的冷凝器或者冷凝器控制器。

3. 灯光系统故障代码。

3.1 E6 故障代码，这个代码通常表示灯光系统的灯泡出现了问题，可能是灯泡本身故障或者是灯泡控制器故障。

解决方法，首先检查灯泡是否正常工作，然后检查灯泡控制器是否损坏，及时更换损坏的灯泡或者灯泡控制器。

3.2 E7 故障代码，这个代码通常表示灯光系统的电源线路出现了问题，可能是电源线路故障或者是电源线路控制器故障。

w w w.jw AF»PL_IAJSiCE TREPAITRITSIG伊莱克斯EHC3507V A型无霜风冷冰箱不启动故障检修□彭永川_台伊莱克斯EHC3507V A型无霜风冷冰 箱，通电后不启动，显示屏无显示，但见屏内有微 弱的LED背光。

该机电控板型号为B1076-ML MLK1007,电源管理芯片为AP3902P-E l(I C3 )。

摘下电控板，上电测得三端稳压块IC1(7805)输出电压在2V 左右波动，其输入电压也偏低；开关电源输出的 5V~12V电压偏低，且带载能力差。

代换300V滤波电容及5V、12V电压滤波电容CE4X E5后试 机,12V电压仍然偏低且不稳定。

检查稳压电路未 发现异常，转向检测1C3外围元件，发现I C3的③ 脚(V C C)电压波动明显。

代换③脚外接滤波电容CE2(如图1所示）后上电，开关电源输出的5V、12V电压正常且稳定,将其安装还原后试机，故障排除<_迓1背面相应部位开孔检查，发现开关变压器初级绕 组断路。

拆下变压器检查，发现引出线烧断，且有 严重打火痕迹，芯片应该是这个原因烧坏的^查此 变压器冷地端只有一个输出绕组，其感应电压经 二极管D8整流、C20滤波后供给三端稳压器LA7805。

板上有几个继电器，线圈电压都是D C12V的，据此判断该开关电源次级输出的电压 为12V。

由于没有同型号变压器，决定外接12V开关电源。

须注意的是，在本机开关电源中，市电全桥整 流输出端(A点）,还接有两只220kll电阻和光耦 IC1。

因该桥式整流输出端没有接滤波电容，其输 出电压是一个频率为100Hz,电压最小值为0V,最大值约310V的脉动电压，如图3所示。

当A点电压高于一定值时,IC1内部发光管导通,次级的接收管也导通,B点发出低电平；当A点电压低于 一定值时,IC1截止,B点输出高电平，这样在交流 电压每次过零点时,B点会输出一个脉冲,C P U据 此判断交流电源电压的过零点，这个电路即是过 零检测电路。

冰箱常见故障和维修方法冰箱常见故障和维修方法一、问维修前先询问客户电冰箱的使用情况故障现象使用年限和故障时，对曾经维修过系统的冰箱要多加留意冰堵，脏堵，冷冻机油是否变质等故障。

二、看(1)首先看蒸发器的结霜情况。

在压缩机运转的情况下如果出现蒸发器表面无霜，结不满霜或结不实等情况，都说明制冷系统工作补正常。

(2)电冰箱的冷藏室不实结霜而是结冻，这种情况是温控器的温差过大开机时间过长造成的。

(3)直冷室双门电冰箱的冷藏室蒸发器总是结满霜，二不实结霜化霜交替变化，这说明温控器发生故障。

(4)查看制冷系统管路的各个焊接口是否有渗漏的痕迹，一般渗漏处会有油渍。

(5)查看压缩机回气管是否有霜，如果结霜说明制冷剂充入过多，如果间冷式的回气管结霜应首先想到由于风扇不转引起的。

三、听(1)接通电源如果启动器和压缩机发出正常的启动声音和压缩机声音，说明启动正常。

如果压缩机发出、“嗡嗡”沉闷声，说明启动不正常(a、电压低压缩机卡缸抱轴。

b、电动机绕组短路或开路 c、启动继电器故障)(2)压缩机运转。

时如果发出“铛铛”的撞击声。

说明压缩机内支撑弹簧断裂或疲劳变形)(3)如果听到蒸发器内有断断续续的憋气声。

这种故障通常为脏堵油堵冰堵(4)如果只有气流声，蒸发器不结霜，这说明系统内制冷剂基本泄露完。

四、摸(1)在压缩机运转时触摸冷凝器上部应该很了，如果用手感觉不热，应该是系统漏气堵塞或压缩机新人不良等故障。

(2)正常时触摸干燥过滤器应有热的感觉，脏堵会造成干燥过滤器温度过低。

温度过高的话四制冷剂过多等原因造成。

(3)压缩机正常工作时触摸压缩机回气管应有凉的感觉，用手摸温度高说明制冷剂少或微堵，如结霜说明制冷剂充入过多(4)用手触摸蒸发器表面。

如果发现蒸发器不满霜说明制冷剂不足或管路微堵。

五、测、检修所测量的内容包括测量温度压力工作电流绝缘电阻直流电阻(1)温度——用电机温度计测量电冰箱的温度。

电冰箱的温度按国家标准吸气温度为三十二摄氏度，蒸发温度为负二十三摄氏度一下，排气温度为五十五摄氏度左右，过冷温度为三十二摄氏度左右。

SERVICE MANUALREFRIGERATION ©Electrolux Home Products S.p.A.Spares Operations ItalyCorso lino Zanussi, 30I - 33080 Porcia (PN)Fax +39 0434 394096S.O.I.Edition: 11.2006Publication no.599 38 43-56ENREFRIGERATORSwithelectric valveandelectronicERF2000DIGITSFACTORY: ZSCONTENT1INTRODUCTION (3)2REFRIGERATION CIRCUIT (5)3ELECTRIC WIRING (6)4COMPONENTS (8)4.1Control panel (8)4.2Electronic boards (9)4.2.1 ERF2000 Power board (10)4.2.2 ERF2000 DIGITS Display board (12)4.3Cooler and freezer compartments (13)4.3.1 Temperature sensors (14)4.3.2 Door switch (14)4.4Compressor compartment (14)4.4.1 Electric valve (15)5MAIN FUNCTIONS (16)5.1Normal (16)5.2FROSTMATIC Function (rapid freezing) (17)5.3COOLMATIC Function (rapid cooling) (17)5.4HOLIDAY Function (valid only for the cooler) (17)5.5Malfunctioning of cooler air temperature sensor (18)5.6Malfunctioning of freezer temperature sensor (19)6ALARMS (20)6.1Freezer compartment temperature alarm (20)7SPECIAL FUNCTIONS (21)7.1Service Mode (21)7.1.1 Starting Service Mode (21)7.1.2 Exiting Service Mode (21)7.1.3 Functions of the Service Mode (21)7.2DEMO MODE (23)7.2.1 Start DEMO MODE (23)7.2.2 Exit DEMO MODE (23)7.2.3 Functions of the DEMO MODE (23)8ACCESSIBILITY (24)8.1Control panel (24)9DISPLAY SYMBOLS (25)9.1Cooler compartment (25)9.2Freezer compartment (26)1INTRODUCTIONThis manual describes the refrigerators with electric valve and ERF2000 DIGITS electronic produced in the Susegana factory called ZS.These models feature:-static (static freezer, static cooler)-total built-in-DOOR ON DOOR door system-single-compressor-electronic control (electronic board ERF2000)-electric valve-digit displayThey are appliances (KBI290DVIT) with the following PNCs:PNC MODEL BRAND925701653JKG9499Juno-Electrolux925701654SC91840-5I AEG-Electrolux925701655SC81840-5I AEG-Electrolux925701656SC81840-5I AEG-Electrolux925701659ERO2923Electrolux925701660ERO2924Electrolux925701661JKG9499Juno-Electrolux925701662SC91840-5I AEG-Electrolux925701663SC91843-5I AEG-Electrolux925701664463.688-2Privileg925701665ERO2923Electrolux925701666ERO2923Electrolux925701667DRC629JE De Dietrich925701668IKE318-5-2Küppersbusch925701669DRC629JE De Dietrich925701670IKE318-5-2Küppersbusch925701671JCG94180Juno-ElectroluxThe controls of the appliance are inserted inside the upper crosspiece.The power control board is ERF2000.The user interface board is ERF2000 (DIGIT display).The appliance has a single-compressor and an electric valve is installed to simulate the operation of a two-compressor.It is possible to switch off only the cooler compartment and let the freezer operate, but not vice versa.The temperatures regulation is the following:•from +8 to +2 °C for the cooler;•from -15 to -24 °C for the freezer.The DIGIT display enables to show the temperatures of the two compartments. The appliance has the following functions:•rapid freezing;•rapid cooling;•freezer temperature alarm,•cooler compartment holiday.The appliance consists of the following compartments:•freezer;•cooler.The evaporating circuit consists of:•roll bond plate evaporator (freezer);•tube evaporator (cooler compartment).Key:A = control panelB = cooler compartmentC = freezer compartment2REFRIGERATION CIRCUITKey:pressor;2.condenser;3.anti-condensation coil;4.dehydrator filter;5.electric valve;6.tube evaporator (cooler compartment);7.plate evaporator (freezer compartment);8.exchanger.The electric valve has 2 outlet capillaries to power:•cooler + freezeror•only the freezer.3ELECTRIC WIRING(Check the specific diagram for each model!)Key:pressormp31.electric valve28.running capacitor (if featured) 41.ERF2000 power boarda.yellow-greenb.brownc.blued.whitee.black4COMPONENTS4.1Control panelKey:Cooler compartmentA.cooler ON/OFF indicator LEDB.cooler ON/OFF buttonC.cooler temperature increase button (+)D.cooler temperature displayingE.cooler temperature decrease button (-)F.COOLMATIC Function LED (rapid cooling)G.COOLMATIC function button (rapid cooling)Freezer compartmentH.ON/OFF indicator LED refrigeratore+freezerI.ON/OFF button cooler+freezerJ.freezer temperature increase button (+)K.freezer temperature displayingL.freezer temperature decrease button (-)M.FROSTMATIC Function LED (rapid freezing) N.FROSTMATIC function button (rapid freezing) O.alarm pilot lamp LEDP.alarm deactivation button4.2Electronic boardsThe electronic board of the appliance consists of:1.ERF2000 power board2.ERF2000 DIGITS display boardThe two electronic boards are connected by means of a flat cable with a connector; therefore, the two boards are available singularly as spare part.4.2.1ERF2000 Power board- View of the electronic board (side of components):1.earth contact2.free3.linepressor5.neutralmp neutralmp8.neutral electric valve9.electric valve1.free2.free1.cooler air temperature sensor2.cooler air temperature sensor3.cooler evaporator temperature sensor4.cooler evaporator temperature sensor5.freezer air temperature sensor6.freezer air temperature sensor1.free2.free1.free2.free3.free4.free1.free2.free4.2.2ERF2000 DIGITS Display boardKey:SW1= reed elementSW2= ON/OFF button cooler+freezerSW3= FROSTMATIC function button (rapid freezing) SW4= freezer temperature increase button (+)SW5= freezer temperature decrease button (-)SW6= cooler ON/OFF buttonSW7= COOLMATIC function button (rapid cooling) SW8= cooler temperature increase button (+)SW9= cooler temperature decrease button (-)SW10= alarm deactivation buttonDGT1= cooler displayDGT2= freezer displayDL1= COOLMATIC function LED (rapid cooling)DL2= FROSTMATIC function LED (rapid freezing) DL3= alarm pilot lamp LEDDL4= LED sign + coolerDL5= ON/OFF indicator LED coolerDL6= LED sign - freezerDL7= ON/OFF indicator LED cooler+freezer4.3Cooler and freezer compartmentsKey:A.freezer air temperature sensor;B.cooler air temperature sensor;C.cooler evaporator temperature sensor.1.cooler door magnet;2.display board reed element.4.3.1Temperature sensors3 NTC sensors are used to detect the temperatures of the two compartments:•freezer air temperature sensor A (located on the freezer cell);•cooler air temperature sensor B (located on the cooler cell);•cooler evaporator temperature sensor C (located on the cooler cell).The sensors A, B and C feature the foamed cable inside the cabinet, therefore they are not replaceable (for further information, please see Service Bulletin 599374122).4.3.2Door switchThe control of the cooler door opening is carried out by using the magnetic switch located on the display board. The magnetic switch is activated by a magnet located inside the cooler door.The control does not imply the activation of the open door alarm, but it is used to light up the lamp of the cooler compartment.4.4Compressor compartmentKey:pressorB.electric valve4.4.1Electric valveThe electric valve is of the 3-way bistable type.It is supplied together with the dehydrator filter.The connections of the electric valve are the following:-central hose with dehydrator filter to connect the condenser;-side hose (GS) to connect the capillary of the freezer circuit;-side hose (KS) to connect the capillary of the cooler+freezer circuit.The electric valve has the following values:-voltage 220 V - 50 Hz-response time <1 secNote:Comply with the electric connections and do not invert the polarity (the 2 terminals FAST-ON have different dimensions).5MAIN FUNCTIONS5.1NormalIn case of first switching on with a freezer compartment temperature higher than 10 °C, the appliance operates with a test cycle (for the factory) for a maximum time of about 1,5 hours.In this period do not perform tests for the correct operation of the appliance, since the loads of the appliance are activated only for internal check (compressor and electric valve).When the appliance is off then:•the compressor is off;•the displays are off.Pushing the ON/OFF button, the displays switch on with the following displaying:•+ symbol on cooler display;•flashing digits of the freezer;•freezer temperature alarm LED (buzzer active).Push the alarm deactivation button to deactivate the buzzer.Regulate the temperatures of the compartments so as to set the following values:•about +5 °C in the cooler;•about -18 °C in the freezer.Warning: Unplug the appliance before operating.5.2FROSTMATIC Function (rapid freezing)The FROSTMATIC function (rapid freezing) is activated by pushing the relative button, therefore:•The pilot lamp relative to the FROSTMATIC function lights up;•The compressor operates in thermostatic conditions and not continuously (like the temperature knob was on max. position) for a duration of about 52 hours, and then it deactivates automatically.To deactivate the FROSTMATIC function push the relative button.5.3COOLMATIC Function (rapid cooling)The COOLMATIC function (rapid cooling) is activated by pushing the relative button, therefore:•The pilot lamp relative to the COOLMATIC function lights up;•The compressor operates in thermostatic conditions and not continuously (like the temperature knob was on max. position) for a duration of about 6 hours, and then it deactivates automatically.To deactivate the COOLMATIC function push the relative button.5.4HOLIDAY Function (valid only for the cooler)The HOLIDAY function is activated when the customer does not want to use temporary the cooler.In this case it is not necessary to leave the cooler door open, because a 15 °C temperature is automatically set to avoid the formation of bad odours inside.To activate the HOLIDAY function push button + (temperature increase) till letter H is shown in the cooler dis-play.Obviously the cooler must be empty because the 15 °C temperature does not allow the preservation of the most common food.the sensor is out of range), then:When the sensor operates again normally, the above described conditions terminate.Characteristics of the NTC sensor:•The display shows cooler temperature sensor faulty.•The appliance operates with preset cycle when the compressor is powered for 40 minutes andremains off for 40 minutes alternatively.the sensor is out of range), then:When the sensor operates again normally, the above described conditions terminate.Characteristics of the NTC sensor:•The display shows freezer temperature sensor faulty.•The appliance operates with preset cycle when the compressor is powered for 40 minutes andremains off for 40 minutes alternatively.6ALARMS6.1Freezer compartment temperature alarmWhen the freezer compartment reaches -11 °C, the temperature alarm activates:•The display digits flash.•The temperature alarm pilot lamp light up.•The buzzer sounds.Push the alarm deactivation button to deactivate the buzzer.When normal conditions are reset (after a power failure):•The acoustic signal deactivates.•The temperature alarm pilot lamp remains on.•The display digits still flash.Pushing the alarm deactivation button:•The highest temperature reached in the freezer compartment is displayed for 5 minutes.•The alarm pilot lamp switches off.•The display digits do not flash anymore.7SPECIAL FUNCTIONS7.1Service Mode7.1.1Starting Service ModeTo start the procedure, perform the following operations:1.Connect the plug to the socket.2.Switch on the appliance with the ON/OFF button.3.Open the doors of the appliance.4.Switch the appliance off with the ON/OFF button.5.Within the first 10 seconds hold down simultaneously the two buttons “FROSTMATIC function (rapid freez-ing)” and “alarm deactivation”.The confirmation of the procedure start occurs with the acoustic signalling of the buzzer which emits a long beep and with the lighting up of all segments of the display.7.1.2Exiting Service ModeThe procedure terminates when one of the following operations is carried out:a.The plug is detached from the socket and reconnected.b.40 minutes have elapsed and no button has been pushed.c.The last phase of the procedure has been reached.7.1.3Functions of the Service ModePress the button “FROSTMATIC function (rapid freezing)” or “alarm deactivation” to skip to the following phase of the procedure.Prsss the “ON/OFF” button to activate/deactivate the loads (compressor, defrosting heater, lamp, fan and air flow regulator damper).List of the phases of the SERVICE MODE:1.All segments of the display are on.2.All segments of the displays are off.3.The number 0 is shown on the display and the load controlled by ACS TH1 [compressor] is checked.To activate/deactivate the load press the button “ON/OFF” (the load is activated when the rapid freezing FROSTMATIC function pilot lamp and the alarm pilot lamp light up).4.The number 1 is shown on the display and the load controlled by ACS TH2 [electric valve] is checked.To activate/deactivate the load press the button “ON/OFF” (the electric valve switches from one side to the other and it is possible to hear a click).5.The number 2 is shown on the display and the laod controlled by ACS TH3 [lamp] is checked.To activate/deactivate the load press the button “ON/OFF” (the load is activated when the rapid freezing FROSTMATIC function pilot lamp and the alarm pilot lamp light up).6.The number 3 is shown on the display and the load controlled by ACS TH4 [not used in this appliance] ischecked.To activate/deactivate the load press the button “ON/OFF” (the load is activated when the rapid freezing FROSTMATIC function pilot lamp and the alarm pilot lamp light up).Note:When the procedure skips to the following phase pressing the button “FROSTMATIC function (rapid freez-ing)” or “alarm deactivation”, the laod keeps its status (for example, if the compressor had been activated, it will remain on also in the subsequent phases); in this way it is possible to check the loads simultaneously.7.Check of the doors.The display digits correspond to the doors: the unit digits correspond to the cooler door, while the ten digits correspond to the freezer door.If the relative door is closed, the displayed digit is 0 otherwise is 1.8.Check of the counter.The display shows an increasing number at intervals of 1 second.This is a counter used by the board for its internal management.9.Check of the temperature sensors.The display shows one of the following codes:Code DESCRIPTIONE0No errorE1Evaporator sensor damagedE2Room temperature sensor damaged (installed on the display board)E4Room temperature sensor damaged (installed on the power board)E50 degree compartment sensor damagedNote:The errors regarding the cooler and freezer air sensors are already displayed during the normal operation. At this point all the phases necessary to chcek the loads have been displayed, therefore it is advisable to in-terrupt the procedure of the SERVICE MODE unplugging and replugging the appliance.Note:If you do not want to interrupt the SERVICE MODE, the procedure continues with some phases dedicated ex-clusively to the factory, therefore they must not to be considered.Also in this case the exit from the SERVICE MODE is carried out unplugging and replugging the appliance.7.2DEMO MODEThe DEMO MODE function is intended only for the commercial activity and not for the user.The internal temperature of the appliance, measured by the air sensors, must be higher than +10 °C so as the function can be activated.7.2.1Start DEMO MODETo start the procedure, hold down the ON/OFF button cooler+freezer and the freezer temperature decrease button for more than 5 seconds.The display digits flash every about 4 seconds.7.2.2Exit DEMO MODETo exit the procedure, hold down the ON/OFF button cooler+freezer and the freezer temperature decrease but-ton for more than 5 seconds or unplug the appliance.7.2.3Functions of the DEMO MODEThe procedure is used only for show in the selling points and allows selecting the temperatures without acti-vating the loads (compressor and electric valve).The displays show:•+ 5 °C for the cooler compartment (flashing display);•-18 °C for the freezer compartment (flashing display).By pushing the temperature regulation buttons, the displays show the temperatures that can be set (flashing display).The internal light switches on when the cooler door is opened.By pushing the cooler ON/OFF button it is possible to simulate the switching off of the cooler compartment (the lamp is off).8ACCESSIBILITY8.1Control panelTo access the control panel and its components (power and display boards) perform the following operations in sequence:a.Open the cooler door.Warning: Disconnect the appliance from the electric power before operating with theappliance.b) View of the control panel of the upper cross-piece.c) Remove the programme plate removing the 2 screw covers and the 2 fixing screws.d) Remove the transparent foil and extract the con-trol support.e) View of the power board.9DISPLAY SYMBOLS9.1Cooler compartmentDISPLAY DIGITS DESCRIPTIONNOT FLASHING It indicates the cooler temperature with normal function [from +2 to +8].FLASHING It indicates the cooler temperature with DEMO MODE func-tion [from +2 to +8].NOT FLASHING It indicates the HOLIDAY function of the cooler compart-ment [15 °C].NOT FLASHING It indicates the malfunctioning of cooler air temperature sensor.NOT FLASHING It indicates incompatibility between the electronic boards. Remedy: check the spare part nos. of the electronic boards.NOT FLASHING It indicates Eeprom parameter writing/reading error. Remedy: replace both electronic boards (power and dis-play).9.2Freezer compartmentDISPLAY DIGITS DESCRIPTIONNOT FLASHING It indicates the freezer temperature with normal function [from -15 to -24].FLASHING It indicates the freezer temperature with DEMO MODE function [from -15 to -24].NOT FLASHING It indicates the malfunctioning of freezer air temperature sensor.NOT FLASHING It indicates incompatibility between the electronic boards. Remedy: check the spare part nos. of the electronic boards.NOT FLASHING It indicates Eeprom parameter writing/reading error. Remedy: replace both electronic boards (power and dis-play).。

冰箱不制冷的原因冰箱常见故障维修技巧冰箱不制冷是冰箱在使用过程中经常遇到的问题，冰箱不制冷非常影响日常生活，而且还要浪费时间去找维修师傅维修，关于冰箱不制冷其实有很多原因，如果自己能维修的话就不需要师傅上门维修了，到底哪些故障会导致冰箱不制冷呢，我们一起来看一下吧。

冰箱不制冷的原因以及解决之道1、打开冷藏室们，检查箱内的照明灯是否亮，以确保冰箱的电源是否接通。

解决办法：检查冰箱的插座是否有电，是否接触不良。

2、报警指示灯亮，同时蜂鸣器发出报警声。

解决办法：有可能是冷冻室的温度过高，一次性在冷冻室里面存放的食物过多等，按一下记忆键，取消报警声音，然后关闭冷冻室门，不要存放太多的食物，避免开门次数过多。

3、冬季不制冷则是以你为室内温度太低，冰箱的温控器档位调的太低。

解决办法：把冷藏室内的温控器档位调到较高的档位上，冬季温度辅助开关的应把开关打开。

4、如果电源没有什么问题，则听听冰箱有没有什么动静，如果听到马达在震动，则说明压缩机没问题，反之则有可能烧坏马达。

解决办法：找到相应的维修地方，找专业人士将马达进行更换。

5、如果使用时间比较长，冰箱不制冷则有可能是没有制冷剂或者是漏氟。

解决办法：添加制冷剂或者氟。

6、压缩机停止工作。

解决办法：检查冰箱是否接通电源，如果接通电源了，则检查其压缩机是否损坏等。

伊莱克斯冰箱不制冷的原因：1、电源线没有插好。

检查电源连接是否正常，打开冷藏室门，看箱内的照明灯是否亮，以确定电冰箱的电源是否接通。

如果没有连通电源，那自然就不可以制冷了啊!2、外围环境等于箱内的环境。

这种情况就有可能是冰箱门没关好，或者是门封密条性能不良或使用过久导致老化，造成冷气外露，导致冰箱内部温度降低不下来。

3、使用的电压过低。

电冰箱按国家标准正常使用电压为187V—242V，如果过低是无法带动电冰箱的运转的。

4、无制冷剂。

压缩机能工作，则可能是制冷系统无制冷剂了。

让冰箱运行几分钟后拔掉插头，仔细听铜管内有无液体流动的声音。