0-1 MT6620_Combo_Module_Application_Note__V2.3_20111024

AN-DISPATCH-010 Rev B11 FEB 2011MotorolaXTL-5000 Radios to 223 Series Adapter PanelsTable of Contents1.0 General (3)2.0 Interconnect Cable Assembly (3)3.0 223 Series Panels (4)3.1 TRA-223 Setup (4)3.1.1 TRA-223 Dip Switch Settings (4)3.2 DSP-223 Setup (5)3.2.1 DSP-223 Jumper Settings (5)3.3 IP-223 Setup (5)3.3.1 IP-223 Jumper Settings (5)2AN-DISPATCH-010AN-DISPATCH-010 31.0GeneralThis application note is intended to assist technical staff with cable assembly and hardware setup of different Telex 223 series adapters (TRA-223, DSP-223 and IP-223) to a Motorola**1 XTL-5000 series mobile radio.2.0Interconnect Cable AssemblyA cable assembly is required to connect to the 26-pin accessory connector of the XTL to the various 223 series adaptor e Table 1 to build the specified cable assembly.1.See “Copyright Notice” on page 7.TABLE 1. Cable Assembly PinoutsTRA-223DB-25 Pin DSP-223DB-25 Pin IP-223DB-25 Pin XTL 26-PinSignal25252523MIC +24242421RX +14141416PTT 77714 & 15GNDMotorolaXTL-5000 Radios to 223 Series Adapter PanelsMotorola XTL-5000 Radios to 223 Series Adapter Panels4 AN-DISPATCH-0103.0223 Series Panels3.1TRA-223 Setup 3.1.1TRA-223 Dip Switch SettingsTo set front panel dip switches , do the following:1. Set to on :•position 4•position 6•position 72. Select 2- or 4-wire operation using:•position 1•position 2•position 3REFERENCE:For more information, see the TRA-223 Technical ManualP/N 803570, Line Connection section. This document is available for download at /.FIGURE 1.XLT Cable Assembly DiagramMotorola XTL-5000 Radios to 223 Series Adapter PanelsAN-DISPATCH-010 53.2DSP-223 SetupNo DSP-223 software programming is required. 3.2.1DSP-223 Jumper SettingsTo set the DSP223 Jumpers, do the following:1. Set to the A position :•J14, J15, J22, J23, J24, J25, J27.2. Set to the B position:•J12 and J13 3. Solder close JP2.To set the operating mode , do the following > Select 2- or 4- wire operation:•J19, J20 and J21.REFERENCE:For more information, see the DSP-223 Technical Manual (P/N 803274), DSP to Console Line Connection section. Thisdocument is available for download at /.3.3IP-223 SetupSetup the desired IP-223 line’s jumpers for Local radio control.3.3.1IP-223 Jumper SettingsTABLE 2. Jumper SettingsLine 1Jumper SettingsLine 2J33, J34 B = 4-WireJ5, J6J16, J21 A = Singled EndedJ19, J20J14Hanging on center pin = 10K Ohm J24J3, J9, J11 A = Single Ended J25, J28, J29J13 B = HighJ27J17, J22 B = 600 OhmsJ10, J15R377Solder bridge the pads together R381Motorola XTL-5000 Radios to 223 Series Adapter Panels 6 AN-DISPATCH-010P ROPRIETARY N OTICEThe product information and design disclosed herein were originated by and are the property of Bosch Security Systems, Inc. Bosch reserves all patent, proprietary design, manufacturing, reproduction, use and sales rights thereto, and to any article disclosed therein, except to the extent rights are expressly granted to others.C OPYRIGHT N OTICECopyright 2011 by Bosch Security Systems, Inc. All rights reserved. Reproduction, in whole or in part, without prior written permission from Bosch is prohibited.*All other trademarks are property of their respective owners.**MOTOROLA and the Stylized M logo are registered in the U.S. Patent and Trademark Office.W ARRANTY AND S ERVICE I NFORMATIONFor warranty and service information, refer to / warranty.F ACTORY S ERVICE C ENTERFactory Service CenterBosch Security Systems, Inc.Radio Dispatch Products8601 East Cornhusker HighwayLincoln, Nebraska, 68507C ONTACT I NFORMATIONSales:Phone...............................................(800) 752-7560Fax ..................................................(402) 467-3279E-mail.......................**********************.com Customer Service:Repair...............................................(800) 553-5992 Technical Support:Phone ..............................................(800) 898-6723********************************************.comWeb C LAIMSNo liability will be accepted for damages directly or indirectly arising from the use of our materials or from any other causes. Our liability shall be expressly limited to replacement or repair of defective materials.AN-DISPATCH-010 7Revision HistoryDocument Title: Motorola XTL-5000 Radios to 223 Series Adapter PanelsDocument Number: AN-DISPATCH-010Revision Change Description DateA Update brand, format and new document number. (Reference rev B)01-OCT-2009B Update Telex website url. Table 2 correction to row 7 column 1.11-FEB-2011。

Quick StartCable ModemMB7420Packaged with your modemPower Cube Coax WrenchEthernet Cable Velcro® Cable TiePara una Guía de Inicio Rápido enespañol, por favor vaya a/MB7420IRLet’s get startedIf you don’t have cable modem service, please order that from your cable service provider.Now connect your modem as shown on the next panel.Connecting to a Coax Cable On the next panel you’ll need to connect your modem to a “live” coax cable. Sometimes a cable will already be available. Sometimes there’s a coax wall jack available, and you connect to the jack with a coax cable. Your modem can also share a coax cable attachedto a TV by using a coax splitter.ON/OFF button POWERConnect the supplied power cube between the power jack and an electrical outlet. RESET button ETHERNET (LAN) Here you can connect a computer, router, HDTV, game station, or other Ethernet-capable device. COAXConnect a “live” coax cable to the modem’s COAX connector as discussed above. (Tighten the nut so it’s finger tight. You maywant to use the supplied wrench. Make the connection snug but not over-tight.)Prepare to activateBy now you should have:•Subscribed to cable Internet service. •Connected your cable modem.•Powered up your cable modem. To do this, the On/Off button needs to be On. Wait for the green online connection light to stop flashing and remain solidly lit. This may take up to 15 minutes.You should have a recent cable bill handy because it has your account number and you’ll probably need that.If you’re asked for information about your cable modem, you can find this on the label on the bottom of the modem.ActivateFor some service providers, you activate by calling them. Many service providers including Comcast and Cox prefer that you activate by opening the Web browser of a computer that’s plugged into theMB7420’s Ethernet port.For Comcast XFINITY Users Only:If the activation page does not appear in your browser, please go to /internetsetup for more information and to activate your modem.If no registration page appears after following the browser instructions above, you need to contact your cable company to register your modem. Here is a listof phone numbers for some major cable service providers. (Note that this list is subject to change.)Comcast 1 (855) 652-3446Time Warner 1 (855) 704 4503Bright House 1 (888) 289-8988Suddenlink 1 (877) 794-2724Cable One 1 (877) 692 2253Cox 1 (888) 556-1193RCN 1 (866) 832-4726Once your cable modem is registered either online orby phone, your service provider will provision yourcable modem service. Typically this takes less than 5 minutes, but in some cases this may take 30 minutesor longer to complete.Once you have activated, you should have Internet access for whatever’s plugged into your cable modem. Congratulations!If your cable modem is NOT working, see Troubleshooting Tips below.If You Want to Connect a RouterThis connection is optional, done after the cable modem is activated. A wireless router lets multiple devices (computers, smartphones, tablets, video devices, game stations…) share your cable modem’s Internet connection, either wirelessly or through a direct Ethernet connection.1. The cable modem and the router should bothbe powered off. 2. Plug the cable modem’s Ethernet cable into therouter’s WAN port. (You may need to disconnect the cable from your computer first.) 3. Power-up the cable modem. Wait for theONLINE lightto be solidly lit. 4. Power-up the router. Wait for the router tocomplete its power-up sequence. 5. The LAN lighton your modem should be litto show the Ethernet connection to your router. Follow your router’s instructions for setting up the router and connected devices. Using a computer or other device connected to the router, try connecting to the Internet. If it works, Congratulations! Installation is complete.Front Panel LightsLIGHTCOLORDESCRIPTIONEthernet LANportGreen or AmberBlinking: Ethernet data is flowing Green: C onnected at highest LANspeed, 1 GbpsAmber: Connected at 10 or 100 Mbps OFF: No connectionOnlineGreenBlinking: Trying to go online ON: OnlineOFF: OfflineUpstreamGreen or BlueGreen Blinking:Ranging in progressGreen ON: Connected on 1 channel Blue Blinking: N egotiating bondedchannel(s)†Blue ON: Bonded with 2 ormore channelsOFF: Upstream not connectedDownstreamGreen or BlueGreen Blinking:Scanning for DS channel Green ON: Connected on1 downstream channelBlue Blinking: N egotiatingbonded channel(s)†Blue ON: Bonded with 2 or morechannelsPowerGreenON: Cable modem power onOFF: Cable modem power off†If a blue light blinks continuously, this indicates partial service (at least one designated channel has not completed bonding). You should still get high Internet speeds, but your service provider may want to know so they can adjust their network.Troubleshooting TipsWhat if I can’t make an Internet connection right after installation?•First turn your cable modem off for at least 8 seconds, then on, to see if that fixes the problem.•Check the connections you’ve made to your cable modem – power, Ethernet, and coax. Are those connections good? •Check that the modem’s power cube is plugged into a live outlet, and that the Ethernet cable is connected securely. •Make sure that your coax cable is live. You can check that by using it with a TV.•Check that you provided the correct setup information to your cable service provider.•Contact your cable service provider to make sure they’ve turned on your Internet service.What if my cable modem has been working, then stops working?•First turn your cable modem off for at least 8 seconds, then on, to see if that fixes the problem.•If the modem’s lights don’t come on, check that the modem is getting power from its power cube and that the modem’s power button is on.•Check your cable modem cables.•Check with your service provider. Sometimes there’s a service outage or some other service issue.What if I’m getting Internet service but my speed is disappointing?•Be sure you know what speed you’re paying for.•Check the speed with a computer plugged into the modem. Use one of the tools found when you search the phrase: broadband speed test.•If you get good speed when a computer’s plugged into the modem, you may have a router problem.•Some video streaming services get bottlenecked, especially at busy times like after dinner. See whether you have the speed problem at less busy times.•Try connecting your cable modem nearer to where the coaxial cable comes into your home. This lets you see whether your home’s cabling is a problem.•If you’re using a splitter with your cable modem, try the cable modem without the splitter to see if that helps. If it does, you may need to get a better splitter.What if I'm told that my cable modem isn't approved for my cable modem service?•That’s probably not true. Leading cable service providers have a list of certified cable modems, and you can check the list for your service provider. You can also find information about certifications at /servicesDo you have any other questions? We have lots more information at /mentorWe like to help.Please visit our support Website or call our support specialists. Our Website has our Motorola Mentor information, and also provides returns and warranty information./support Email:************************* Phone: 800-753-0797Limited WarrantyMTRLC LLC warrants this product against defects in material and workmanship for a warranty period of 2 years. To read the full warranty, please go to /warrantySafety PrecautionsThese precautions help protect you and your cable modem. Do not put the cable modem or its power cube in water, since this is a shock hazard.The cable modem should normally be installed indoors. If you use it outdoors, protect it from moisture and be careful about temperature.Your cable modem should be operated in an environment that’s between 32 and 104° Fahrenheit (0 to 40° Centigrade). Your cable modem should not be in a confined space. There should be room for air flow around the top, front, and sides of the cable modem.Make sure to use your cable modem’s power cube and a compatible electrical outlet.FCC StatementThis device complies with Class B Part 15 of the FCC Rules. Operation issubject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received,including interference that may cause undesired operation. Only coaxialcables are to be used with this device in order to ensure compliance with FCC emissions limits. Accessories connected to this device by the user mustcomply with FCC Class B limits. The manufacturer is not responsible for any interference which results from use of improper cables, or which results from unauthorized changes or modifications to the device.©MTRLC 2016. MOTOROLA and the Stylized M Logo are trademarks orregistered trademarks of Motorola Trademark Holdings, LLC. and are used under license. All rights reserved.27727-EL-B/3155。

各平台操作系统查看HBA卡WWN方法AIX1.获得AIX主机连接的光纤设备:# lsdev -Cc adapter -S a | grep fcsfcs0 Available 09-08 FC Adapterfcs1 Available 09-09 FC Adapter其中,显示有两块光纤卡：fcs0和fcs1。

2.查看光纤卡的WWN号：# lscfg -vpl fcs0fcs0 U787B.001.DNWG664-P1-C1-T1 FC AdapterPart Number.................10N8620Serial Number...............1B74404468Manufacturer................001BEC Level....................ACustomer Card ID Number (5759)FRU Number.................. 10N8620Device Specific.(ZM) (3)Network Address.............10000000C96E2898ROS Level and ID............02C82138Device Specific.(Z0)........1036406DDevice Specific.(Z1) (00000000)Device Specific.(Z2) (00000000)Device Specific.(Z3) (03000909)Device Specific.(Z4)........FFC01159Device Specific.(Z5)........02C82138Device Specific.(Z6)........06C12138Device Specific.(Z7)........07C12138Device Specific.(Z8)........20000000C96E2898Device Specific.(Z9)........BS2.10X8Device Specific.(ZA)........B1F2.10X8Device Specific.(ZB)........B2F2.10X8Device Specific.(ZC) (00000000)Hardware Location Code......U787B.001.DNWG664-P1-C1-T1其中标红的部分就是光纤卡的WWN号。