海工船英语词汇

格式：doc
大小：126.00 KB
文档页数：40

下载文档原格式

海洋工程专业词汇

船舶英语必备实用词汇

船舶英语必备实用词汇船舶英语词汇dugout独木舟barge驳船kayak(爱斯基摩人的)木排outrigger桨叉架船rowing boat划艇(美作：rowboat)gondola(意大利的)长平底船whale mother ship捕鲸母船hydrofoil水翼船catamarans双体船dredger挖泥船boat船brig， brigantine双桅船canoe小船，独木舟caravel快帆船cargo boat货船coaster近海贸易货船cod-fishing boat捕鳕鱼船whaler捕鲸船collier运煤船battleship战船shallop小型战船coastguard cutter，coastguard vessel巡逻艇，缉私艇revenue cutter缉私船patrol boat巡逻艇minesweeper扫雷艇torpedo boat鱼雷艇frigate轻护航舰gunboat炮舰submarine潜水艇destroyer驱逐舰corvette轻巡洋舰cruiser巡洋舰aircraft carrier航空母舰ferry， ferryboat渡船，渡轮fishing boat渔船freighter货船galleon大型帆船galley大划桨船hovercraft气垫船icebreaker破冰船launch艇lifeboat救生艇lighter驳船liner， ocean liner远洋班轮merchant ship， merchantman商船motorboat摩托艇outboard尾部装有马达的小艇paddle steamer， paddle boat明轮船 passenger boat客船piragua， pirogue独木舟raft木筏sailing boat， sailing ship帆船schooner纵帆船ship船skiff小艇sloop单桅船steamer， steamship汽轮tanker油轮trawler拖网渔船tug， tugboat拖轮vessel船yacht游艇yawl船载小艇船舶工程专业英语口语词汇1、柴油日用柜 Diesel oil daily tank2、柴油澄清舱 Diesel oil setting tank3、燃油日用柜 Fuel oil daily tank4、燃油澄清舱 Fuel oil setting tank5、滑油澄清舱 Lubricating oil setting tank6、滑油储藏舱 Lubricating oil store tank7、滑油循环舱 Lubricating oil circulating tank8、燃油溢油舱 Fuel oil overflow tank9、燃油油渣舱 Fuel oil sludge tank10燃油深舱 Fuel oil deep tank11滑油污油舱 Lubricating dirty oil tank12滑油溢油舱 Lubricating oil overflow tank13滑油油渣打舱 Lubricating oil sludge tank14主机淡水膨胀水箱 M.E fresh water expansion tank15付机淡水膨胀水箱 A.E fresh water expansion tank16、淡水压力柜 Fresh water pressure tank17、热水压力柜 Hot water pressure tank18、饮水压力柜 Drinking water pressure tank19、淡水舱 Fresh water tank20、饮水舱 Drinking water tank21、锅炉水舱 Boiler water tank22、分油机工作水箱 Purify operating water tank23、汽缸油日用柜 Cylinder oil daily tank24、尾管滑油重力柜 Gravity tank of tube oil25、排气水封箱 Exhaust seal water tank26、蒸馏水水舱 Distilling water tank27、污水井 Bilge well1、滑油系统 Lubricating oil piping system2、燃油系统 Fuel oil piping system3、海水系统 Sea water piping system4、缸套水系统 Cylinder cooling water piping system5、启动空气系统 Start air piping system6、控制空气系统 Control air piping system7、排气系统 Exhaust piping system8、日用供水系统 Daily water piping system9、蒸汽系统 Steam piping system10 、锅炉给水和凝水系统 Feed water and condensate of boiler piping system11、燃油净油系统 Fuel oil purified piping system12、燃油输送系统 Fuel oil transport piping system船舶英语词汇。

船舶与海洋工程专业单词总结

3.甲板: Deck 甲板板 deck plating 甲板开口 deck opening 甲板边板 deck stringer 甲板骨架 deck framing 甲板纵桁 deck girder 甲板纵骨 deck longitudinal 甲板强横梁 deck transverse 甲板横梁 deck beam
1.货舱： Cargo hold
甲板间舱（二层舱） tween deck space
二层甲板 tween deck 上层甲板间舱 upper tween deck
space 中层甲板间舱 mid tween deck space 下层甲板间舱 lower tween deck
space 下层舱 lower hold 肋骨 frame 货舱出入口 access
液压折叠式舱口盖 hydraulicfolding hatchcover
多板滚动式舱口盖 multipanel hatchcover
滚动式舱口盖 rolling hatchcover 滑动式舱口盖 sliding hatchcover 舱盖板 hatch cover plate(panel) 托架 carrier 导轨 guide rail 轨道轮子 track wheel
分舱甲板 subdivision deck 强力甲板 strength deck 开敞甲板 open deck 露天甲板 exposed (weather)
deck 遮蔽甲板 shelter deck 游步甲板 promenade deck 旅客甲板 passenger deck
升高甲板 raised deck 前升高甲板 raised fore deck 后升高甲板 raised quarter deck 车辆甲板 vehicle deck 甲板覆层 Deck covering 化学敷料 composition 绝缘层 insulation

海洋海工英语词汇总结

be)subject to…经受…(in) duplicate 一分两式(to be) buttered (焊接的)长肉(to) drive piles 打桩4:1 taperd transition bevel 四比一过渡坡口AA resulting formB 由B导致AA-60 fire door A-60级防火门abrasive （喷砂用的）磨料abrasive paper 砂纸AC generator 交流发电机AC m otor 交流发动机accelerated corrosion testing 加速腐蚀试验acceptance criteria 合格准则access hole(for welding) =cope hole （焊接）工艺孔accom m odation and power platform(APP) 生活动力平台according to=in accordance with=in line with =as per =in the light of 按照acetylene gas 乙炔acid electrode 酸性焊条acid proof cem ent 防酸水泥additive 添加剂adhere to 遵守（动词）adherence to 遵守（名词）adjacent colum ns 相邻立柱adverse com bination of loads 荷载的不利组合adverse condition 不利条件aeronautical radio system航空无线电AFC(approved for construction) 建造批准aforem entioned 上述的aft winch 船艉绞车agitator 搅拌器a-hundred-year return period 百年一遇air blower 鼓风机air com pressor 空压机air driven pum p 气动泵air hoister 气动绞车air m anifold 气包air tight test 气密性试验aircraft obstruction beacon 航空障碍灯air-hose 风带alarm buzzer 报警蜂鸣器alarm horn 报警喇叭aliphatic polyurethanel 脂肪族聚氨脂漆allowable(working)stress 许用应力Aluminum alloy anode 铝合金阳极Aluminum ingot 铝锭aluminum paint 银粉漆aluminum sheet 铝皮am bient air tem perature 环境气度am bient tem perature 环境温度anchor block 地锚块anchor bolt 地脚螺拴anchor ground 锚地anchor pile 锚桩anchor profile/pattern 涂桩表面的粗糙度anchor rack 锚架anchoring buoy 锚泊浮筒angle of incidence 入射角angle of reflection 折射角angle probe m ethod超声波斜射探伤angle steel 角钢angle valve 角阀anode core 阳极芯子anode end face geom etry 阳极端面几何形状anode life 阳极寿命anode potential 阳极电位anode stand-off post 支架式阳极的立柱anodic resistance 阳极电阻anti corrosive paint 防锈漆anti-electrostatic floor 防静电地板antipollution m easures 防污染措施API specified requirem ents API规定的要求apparent batter 视斜度applicable API specification API适用范围approach-departure sector 直升飞机起落扇行区appurtenance =attachm ent =accessory =auxiliary 附件arc air gouging 碳弧气刨arc cutting 电弧切割arc strike 弧击argon arc welding 氩弧焊argon arc welding m achine 氩弧焊机arti culated tower m ooring system 铰接塔系泊系统artifi cial island 人工岛as per 按照as-built 完工as-built dossier 完工资料as-built drawing 完工图as-rolled 轧制状态assem ble 组装(动词)assem bly 组装(名词)associated gas 伴生气at the option of A 按A的意愿Atm ospheric diving system =unpressurized diving system 常压潜水系统atm ospheric vent 放空管attachm ents 附件auto fire alarm system 火灾自动报警系统autom atic spraying system 自动喷淋系统Bback chipping 清根back gouging 反面气刨backing weld 打底焊道backpressure regulator (self contained) 背压式调节阀(自力式) backwash return pum p 反冲洗回流泵backwash surge tank 反冲洗罐backwash tank 反冲洗水罐Ball hardness 布式硬度ball valve 球阀bar (截面较小的)圆钢方钢六角钢等bar chart 统计用的柱状图barge bum per 靠船件barge strength and stability 驳船强度及稳性barrel (管件的)加厚段base m etal 母材、基本金属basi c design 基本设计basi c drawing 基本设计图basi c electrode =lim e type covered electrode 碱性焊条battery room 蓄电池间beam depth 梁高beam path distance 超声波发射程距bearing strength of the ground 地基承载力bearing stress 支撑应力before welding is initiated 始焊前bending m om ent 弯矩bending stress 弯曲应力bevel 坡口bevel angle 坡口面角度beveling/cham fering 开坡口bid / tender for …投标bid ddrawing 招标图纸bilge / fire pum p 舱底污水-消防两用泵bilge alarm system污水报警系统blast cleaning喷砂除锈blind flange 盲法兰blind spectacle flange 快速盲法兰blow count 打桩的锤击数blow out preventer system(BOP system) 防喷器系统blowdown vessel 排放罐blowhole;gas pore 气空blowout preventer stack 防喷器组boat landing 登船平台bolt,nut and washer 螺栓、螺母及垫片bolted connection 螺栓连接boom吊机扒杆boom angle 吊臂倾斜角bore hole 镗孔boss with plug 带有丝堵的管座bottom echo 底面回声bottom sitting drilling platform 坐底式钻井船boundary condition 边界条件bow 船艏box beam 箱形梁box type joinnt 箱形节点brace 拉筋bracelet anode 手镯式阳极branch m em ber 支杆breathing apparatus , respirator 防毒面具bridge 栈桥bridge (overhead) crane 天车吊brittleness 脆性brush coating 用毛刷涂漆buckle fastener 绑带build-up girder 组合梁bulb angle 球扁钢bulk head 隔板，舱壁buoyant turret m ooring 浮筒转塔式系泊burn through 烧穿burner 气焊工burr and flashing 飞边毛刺business and m anagem ent 经营管理butterfly valve 蝶阀butt-welded seam 对接焊缝Ccable layer 敷缆船cable rack / tray 电缆托架caisson 沉箱caisson washing pum p 洗船泵caisson-type platform 沉箱式平台can （管件的）段cantilever beam 悬臂梁cantilever jack-up rig 悬臂自升式钻井船cantilever well m odule 悬臂式井口模块cap beam 帽梁capped steel 半镇静钢capsizing lever 倾覆力臂capsizing m om ent = overturn m om ent 倾覆力矩carbon arc air gouging 碳弧气刨carbon dioxide cylinder 二氧化碳气瓶carbon equivalent 碳当量carbon-dioxide(CO2) arc welding 二氧化碳气体保护电弧焊cargo m aster system 货油舱总监控系统cargo tank cleaning m achine 洗舱机carrier （搬运）小车carry out = perform = conduct =execute 进行、执行catenary anchor leg m ooring(CALM) 悬链锚腿系泊cathodic protection 阴极保护cellar deck 底甲板cellar shutdown panel(CSDP) 井口系统关断盘cem ent grout 水泥浆cem enting vessel 固井船center line 中心线center of buoyancy 浮心center of floatation 漂心center of gravity 重心center punch 冲子central control room(CCR) 中央控制室central processing platform中心处理平台centrifugal pum p 离心泵centrifuger 离心机ceram ic fibres 防火陶棉ceram ic tiles 瓷砖certi fying authority 第三方检验机构chain block 倒链chair wi th arm-rests 带扶手的半软椅cham fering 开坡口channel steel 槽钢charpy-V notch energy 夏比V形缺口韧性值charpy-V notch im pact test 夏比V形缺口冲击试验chart datum 海图基准面check random ly 抽检check valve 止回阀checkered plate 花纹板chem ical com position 化学成分chem ical injection package 化学注入撬chem ical injection system 化学药剂注入系统chem ical seal 化学密封chipping hamm er 敲渣锤chisel 风铲chord m em ber 弦杆Christm as tree 采油树circum ference 周长circum ferential weld 环焊缝classification survey 入级检验clean water injection pum p 清水注入泵clean water surge tank 清水缓冲罐clearance 间隙client 业主、顾客close drain tank 闭式排放罐closed drain pum p 闭式排放泵closed / open circuit 闭/开路closed drain tank 闭式排放罐clustered well heads 丛式井口CO2 cylinder unit CO2气瓶组CO2 ex tinguisher CO2灭火器coal tar epoxy paint 含焦油环氧涂料coam ing 档水扁钢coating 涂装coating interval 涂装间隔coefficient 系数cold form ed pipe 冷卷管cold shut 冷隔cold work 冷加工、冷作collapse ring 加强环板colum n 立柱com bustible gs detector 可燃气体探测器com e-along 手搬葫芦comm ercial blast cleaning 普通级喷砂除锈comm issioning 调试com pile and m aintain a docum ent 编制和保存文件com plete penetration groove weld 全熔透坡口焊com pletion riser 完井立管com plex with 符合（名词）com ply with 符合（动词）com posite rockwool ceiling复合岩棉天花板com posite rockwool panel复合岩棉板concentric reducer同心大小头conceptual design 概念设计conceptual drawing概念图纸concrete platform 混凝土平台condensate drum 冷凝液罐condensing water 冷凝水conductor隔水套管conductor guide套管导向cone 大小口、锥体conform to = stick to = adhere to符合、遵守connection 节点、连接consum ption rate 阳极消耗率continuous beam 连续梁continuous double fillet weld双面连续贴角焊continuous weldings连续焊contract合同contraction stress收缩应力contractor 承包商contractor（合同供方）control valve (accessories handwheel) 带手轮的控制阀control valve assem bly 控制阀总成coordinates 坐标系coordination 协调cope hole （焊接）工艺孔corrective and preventive action 纠正和预防措施correlation curve 相关曲线corrosion allowance 腐蚀余量corrosion coupon 腐蚀挂片corrosion protection 防腐corrugated plate interceptor 斜板分离器couplant UT用的耦合剂coupling 连轴器、管箍crack裂纹crane barge,crane vessel起重机crane support吊机支撑crater 焊口crawler crane履带吊车cri teria（验收）标准cross angle 交叉角cross section横截面crow bar撬杆cruciform bollard 单十字带缆柱crude cooler 原油冷却器crude filter 原油过滤器crude heat ex changer原油换热器crude loading /export pum p原油外输泵crude loading pum p原油装载泵crude oil drain tank原油排放舱crude preheat ex changer 原油预热器crude suction strainer原油吸入滤器crude transfer pum p原油输送泵cup support 垫墩curing tim e （油漆的）固化时间current capacity （阳极的）电流容量current density（阳极的）电流密度current direction 海流方向curvature radius 曲率半径custom er (比较purchaser) 客户（签合同后，客户变需方）cut by torch 以火焰切割cut off 割除、割除物cutoff allowance 切割裕量cutting plan 排版图cutting sheet单件图DDAC curves 距离-振幅曲线daily diesel filter日用柴油滤器dam age_prone connection 易破坏的节点dam per , dam pener 减振器DC generator 直流发电机ddry chem ical ex tinguisher 干粉式灭火器Decibel (dB) 分贝deck beam甲板梁deck cover 甲板敷料deck crane 甲板吊车deck floor plate 甲板板deck water seal unit甲板水封装置deep freeze com pressor 深冷压缩机deepwater jacket 深水导管架defect /default /disconnection 缺陷deflection 挠度dehydration degassing vessel 脱水除气器dehydration preheater脱水预热器dehydrator feed pum p电脱水供给泵delivery of m aterials 材料交货derrick barge 回转式起重船desander 除砂罐design basis 设计基准design drawing详细设计图design param eters 设计参数detail 详图detail design详细设计develop /establish a docum ent编制文件dew point露点DFT(dry film thickness) 干膜厚度diagonal brace 斜拉筋dial gauge 百分表diaphragm 隔板diaphragm valve隔膜阀die stamp 钢印diesel filter coalescer 柴油过滤净化装置diesel generator set柴油发动机diesel oil daily tank with heater 柴油日用罐（带加热器）diesel pum p 柴油泵diesel storage tank with heater 柴油储罐（带加热器）diesel storage tank 柴油储罐diesel tank 柴油罐diesel transfer pum p 柴油输送泵differential pressure control valve 差压控制阀diffuser 布风器dihedral angle 二面角dim ensional check s 尺寸校验direct /alternating current arc welding 直/交流电弧焊direct current em ergency supply直流应急电源disassem bling拆除discontinuity缺陷displacem ent oil tank 置换油罐distortion from welding 焊接变形distress signals 遇险呼救信号diver 潜水员diver support vessel潜水作业船docum ent approval and issue 文件的批准和下发docum entation文件编制dog 组装用的刀把dolphin 系缆柱dom estic sea water pum p 生活海水泵double agent facility 双介质灭火装置double bevel groove K形坡口double bollard 双柱带缆柱double groove 双面坡口double plate 垫板、包板double probe m ethod 双探头法doulbe bed 双层床doulbe V groove 双面V形坡口（X形坡口）down hill welding 下向焊drain pit 排水池draught gauge 吃水标尺drawing and specification 图纸及技术规格书drawing types 图纸种类dredger 挖泥船drift pin 心轴、销子drift test 管流试验、管线试通drill 钻头drilling m odule 钻井模块drilling platform 钻井平台drilling tem plate 钻井基盘drillship ,drilling ship 浮式钻井船driving voltage 驱动电压dryer 烘箱dry-type tree 干式采油树during the course of fabrication 在制造过程中during the life of structures 结构寿命期间dye penetrant inspection 着色检验dynam ic-positioning rig 动力定位钻井船Eearth lead 地线eccentric reducer 偏心大小头echo height 回波高度edge crim ping （卷管的）压头edge preparation 坡口加工effective throat thickness 焊缝计算厚度elbow 弯头electric dehydrator 电脱水器electric desalter 电脱盐器electric drill 手电钻electric heater 电加热器electric subm ersible pum p 电潜泵electrical connection 导电连接electric-hydraulic valve 电-液操作阀electrochem ical property 电化学特性electrode 电焊条electrode covering 焊条药皮electrode holder 焊把、焊钳electrolyte 电解质electro-slag welding 电渣焊接elevation(EL) 标高、立面图elongation 延伸率em ergency air com pressor 应急空压机em ergency ballast control system 应急压载控制系统em ergency BOP recovery system 防喷器紧急回收系统em ergency generator 应急发电机em ergency light 应急照明灯em ergency power station 应急电站em ergency shutdown 紧急关断em ergency shutdown system(ESD) 应急关断系统em ergency switch board 应急开关柜em ergency switch room 应急配电间em ery cloth 金刚砂布em ulsion transfer pum p 乳化油输送泵engine room 动力舱、机舱engineering geotechnical vessel 工程地质船engineering vessel 工程船舶entire length 全长equal angle 等边角钢equation 公式equipm ent base 设备底座erection 安装ERW(electric resistance welding) 电阻焊escape route 逃生路线essential variable 焊接基本参数excess of weight 超重existing structure 已有结构explosion proof equipm ent 防暴设备exposure distance 防火距离extent of defect in % 缺陷百分率extent of inspection 检验范围extent of repair 返修率external surfaceof brace 拉筋的外表面extra m argin of stress 应力裕量Ffabricated wide flange shape 焊接成的宽翼缘型钢fabrication aids 制造辅助物（如临时吊点）fabrication design 加工设计fabrication drawing 加工设计图fabrication phase 制造阶段fabrication sequence 制造顺序fabrication yard 制造场地face bend test 表面弯曲试验facsimile transceiver 传真收发两用机fastener 紧固件fatigue dam age 疲劳破坏field assem bly 空间组队、现场组对field m ating point 海上对接点（如导管架与组块对接点）field splice 现场拼接field weld 现场焊缝fiexed platform 固定式平台fiexed tower SPM 塔系泊fifty year return period 五十年一遇file 锉刀filler m etal 填充金属final fabrication tolerance 最终制造公差finish coat 面漆first coat 底漆finished product 成品finite elem ent analyses 有限元分析fire alarm siren 火灾警笛fire and gs detecting system 火灾-可燃气探测系统fire control panel 消防控制盘fire dam per 防火风闸fire door closer,fire proof door 防火门fire ex tinguishing system 消防系统fire fighting water, fire water 消防水fire foam hadrant 消防泡沫拴fire hose station ,hose box 消防箱fire m onitor 消防炮fire panel 火灾-可燃气报警显示盘fire proof wall ,fire wall 防火墙fire protected plastic tiles 防火塑料地板fire protection wall 防火墙fire station 消防软管箱fire waater hose rock 消防水软管fire water deluge system 大水量灭火系统fire water hydrant 消防水拴fire water jock ey pum p 消防水增压泵fire water lift pum p 消防水提升泵fire water pum p 消防水泵fire water/foam m onitor 消防炮（水或泡沫）fire-fighting vessel ,fire boat 消防船firem an box 消防员箱first aid kit 急救箱first stage hydrocyclone 一级水力旋转器first stage separator 一级分离器fitter 组装工fit-up 坡口组对fixed crude oil washing m achine 固定式原油清洗机fixed drilling platform 固定式钻井平台flam e arrester 阻火器flam e cutting 火焰切割flam e cutting droplets and debris 火焰切割形成的熔滴和料头flam e cutting m achine 火焰切割机flam e cutting torch 火焰割枪flamm ability limits 可燃度极限flange 冀缘、法兰flare assem bly 火炬总成flare boom 火炬臂flare drum 闪蒸罐flare pilot gas 火炬引燃器flare scrubber 火炬分液器flare tower 火炬塔flat bar 扁钢flat plate anode 扁阳极flat position / downhand welding 平焊flat wekding 平焊flaw 裂纹flaw detectability 缺陷检测灵敏度flaw echo 缺陷回声flexible hose 柔性软管flexible riser 挠性立管floater controlled valve 浮球控制阀floating cargo hose浮式输油软管floating loading hose浮式装油软管floating oil production and storage uni t(FPSU)浮式生产储油装置floating oil storage unit 浮式储油装置floating production ,storage and off-loading tanker 浮式生产储油外输轮floating production platform 浮式生产平台floating state 漂浮状态flooding 注水floppy disk 软盘flow chart 流程图flow indicator(FI) 流量显示器flow quantity recorder(FQ) 累计流量计flow swith 流量开关flux 焊药flux cored arc welding(FCAW) 药芯焊flux-cored electrode 管状焊条flux-cored wire 药芯焊丝foam extinguishing system 固定式泡沫灭火系统foam m onitor 泡沫炮foam station 泡沫站fog horn ,fog signal 雾笛folding bed 折叠床folding chair 折叠椅foot print 被交位置foot valve 底阀forecastle 艏楼forem an 领班forged steel(FS) 锻钢fork lift 铲车，叉车form ing 压制成型form ing of plates into tubular 由板卷成管form ula /equation of carbon equivalent 碳当量公式four way valve 四通阀fracture toughness 断裂韧性fram e structure 梁格结构free water knockout vessel 流离水分离器fresh water pressure vessel 淡水压力罐fresh water pum p 淡水泵fresh water tank pum p 淡水罐fresh water tank with electric heater 淡水罐（带加热器）friction coefficient 摩擦系数fuel gas com pressor packge 燃气压缩机撬fuel gas heater 燃料气加热器fuel gas scrubber 燃气洗涤器fuel gas treatm ent package燃料气处理撬fuel oil drain tank燃料油排放罐fuel pum p 燃油泵full coupling 全螺纹的接头full penetration weld 全溶透焊缝funnel-shaped guide喇叭口状导向furnace熔炉、加热炉fusible plug 异熔塞fusion/bond line 熔合线Ggantry crane 龙门吊gap gauge 间隙尺gas bottle 气瓶gas cutting 气割gas cutting m achine with m agnetic wheels 磁轮式气割机gas detector 可燃气体探测器gas injection m odule 注气组块gas m etal arc welding 熔化极气体保护焊gas m etal arc welding (GMAW) 熔化极气体保护焊gas tungsten m etal arc welding (G TAW) 钨极气体保护焊gas tungsten m etal arc welding (G TAW) 钨极气体保护焊（含氩弧焊）gas turbine generator set 燃汽轮机发电机组gas turbine power generator 燃汽轮机发电机gas welding 气焊gasket 垫圈gate valve 闸阀geophysical survey vessel 物探船girders and webs 水平绗材和垂直绗材girth weld 环缝global positioning system (GPS) 全球定位系统globe valve (norm ally clsoed) 截止阀（常闭）glycerin 甘油gouging 气刨graphite crucible 石墨坩埚grating 格栅gravity dam per 重力风闸gravity platform 重力式平台gravity type foundation 重力式基础grease 黄油、润滑油grind 打磨grinder 砂轮机grinding 打磨（名词）grinding m achine 砂轮机grit 石英砂grit blasting 喷丸除锈groove 熔池groove angle 坡口角ground flush 磨平gs export facility天然气外输设备guard filter 保护滤器guide funnel 导向喇叭口guide structure 导向结构gusset 节点板、筋板guyed tower platform拉索塔平台Hhalf nipple 一端带螺纹的接头halogenated hydrocarbon cylinder 卤化烃瓶halogenated hydrocarbon cylinder local panel 卤化烃就地控制盘halogenated hydrocarbon cylinder local panel 卤化烃就地控制盘halogenated hydrocarbon fire ex tinguishing system 卤化烃灭火系统hamm er 锤子hand operated pum p 手动泵hand winch 手动缆绳车handrail 栏杆hard hat 安全帽hardener 固化剂hauling to the front 牵引至码头前沿hazardous area 危险区heat affected zones(HAZ) 热影响区heat detector 热探测器heat ex changer 热交换气heat m edium drain tank 热介质排放罐heat num ber 炉号heat traced pipeline 伴热管线heat treater 加热热处理器heat treatm ent 热处理heater 加热器heater treater 热处理器heater treater feed pum p 热处理器供热泵heating m edium boiler package 热介质锅炉撬heating m edium circulating pack age 热介质循环撬heating m edium collection tank 热介质收集罐heating m edium diesel daily tank 热介质从柴油日用罐heating m edium drain pum p 热介质排放泵heating m edium drain tank 热介质排放罐heating m edium expansion vessel 热介质膨胀罐heating m edium m ake-up pum p 热介质再启动泵heating m edium oil , therm al oil 传热介质油heating m edium storage tank 传热介质油储存罐heating,ventilation and air conditioning system(HAV) 采暖、通风、空调系统heave wall section 厚壁段heavy can 节点加厚段heavy duty coating 厚层防腐heavy plate 厚板heavy wall pipe 厚壁管helideck 直升机甲板helm et 安全帽hex head bolt 六角头螺栓high /low pressure switch(PSHL) 高-低压开关high concentration gas alarm 高浓度可燃气报警high pressure condensate tank 高压凝析油罐high pressure flare 高压火炬high pressure separator(HP separator) 高压分离器high strength steel 高强度钢high-low 错皮histogram （统计用）直方图hold 待定hold point （检验的）停点holder 焊钳holiday detector 气孔探测仪horizontal distance 水平距离horizontal position welding 横焊horizontal welding横焊hose 软管hose assem bly 软管总成hose connection 软管接头hose handling crane软管起升吊机hose reel 软管轮hot dip galvanizing热浸锌hot water pressure vessel with electri c heater热水压力罐（带加热器）hot work 明火作业H-shape H型钢hum an life and property 人民生命财产hydrant 消火栓hydraulic pile_driving hamm er 液压打桩锤hydraulic press 液压机hydrostatic/hydraulic test 水压试验hyperbaric diving system =pressurized diving system 高压潜水系统Iice-breaker 破冰船if (when)necessary 若有必要ignitor 点火器imm ersion suit 防寒救生衣im pact resistance 耐冲击性im pressed-current protection system 外加电流保护系统in accordance with 按照in any jack et plane 在任意导管架平面内in line with 按照in the light of 按照inclined stair 斜梯include but not limited to 包括但不限于included /groove angle 坡口角度inclusion 夹杂物incom plete fusion 未熔合incom plete penetration 未焊透inflatable liferaft气胀式救生筏inlet gas generator pack age 惰性气体发生器撬inorganic Zine prim er 无机锌底漆in-process inspection 工序间的检验inside diam eter(ID) 内径inspection 检验inspection criteria 检验标准installation site 安装现场instrum ent air receiver 仪表空气接受器instrum ent capillary tube 仪表控制管线instrum ent m aster control room 仪表总控制室insulating flange 绝缘法兰insulation 保温insulation(heat traced) 保温加伴热intact / dam age stability interference 完整/破损稳性（杆件之间的）相碰，打架intergranular corrosion 晶间腐蚀interm ediate strength steel 中强度钢interm ittent welding 断续焊internal and ex ternal beveling 内外坡口internal diam eter 内径internal quality audits 内部质量审核internal stress 内应力interpass tem perature 层间温度intersected pipe 被交管intersection line 相贯线invitation for bid =call for bid 招标Jjack 千斤顶jacket 导管架jacket cap 导管架帽jacket handling 导管架扶正jacket launching and upending 导管架下水及竖立jacket launching barge 导管架下水驳船jacket leg 导管架腿柱jacket leveling 导管架调平jacket lifted on and off the barge 吊上及吊下驳船的导管架jacket lifting eye 导管架吊耳jacket m odification 导管架改造jacket panel 导管架片jacket panel assem bly 导管架片组对jacket positioning 导管架定位jacket securing 导管架固定jacking state 升降状态jacking system升降系统jack-up rig 自压式钻井船jockey pum p 供消防水干管的补给水泵joint can 节点加厚joint detail 节点详图J-tube J形管junction box(explosion proof) 接线箱（防暴型）Kkey plan 总图、索引图killed steel 镇静钢kingpost 将军柱Llack of fusion 未融合lack of penetration 未焊透ladder 直梯ladle analysis 熔炼分析lam ellar tearing 层状撕裂lap 焊缝盖面lap welding 搭接焊lateral load 侧向荷载launch / cargo barge 滑道式/装载式驳船launch way and rocker 滑道和摇臂launching and uprighting of a jack et 导管架的下水和直立launching truss 下水珩架lay barge 铺管船lead sections and subsequent add-ons of piles 首桩及后续桩段leak test 密封性试验（试漏）leg 桩腿、导管leg of a fillet weld （角焊缝）焊角高度level 水平仪level gauge (with drain) 液位仪（带排放）life boat 救生艇life boat davit ,davit 吊艇架life buoy 救生圈life jacket 救生衣life raft ,life float 救生筏lift cal culation 吊装计算lifting gear 吊艇机lifting load 起吊荷载lifting lug 吊点lifting padeye 吊点lifting up of panel structure 单片起吊light type com bustible gas detector 轻质可燃气体探测器line pipe 管线管line throwing apparatus 抛绳装置liquid trap 液体捕集器living quarter 生活块LNG carrier ,LNG tanker 液化天然气运输船loading arm 输油臂loading flexible hose 柔性装载软管loadout and seafastening 装船固定local deform ation 局部变形local stress 局部应力longitudinal seam / weld 纵焊缝low explosion lim it(LEL) 爆炸下限low heat input 底热量输入low hydrogen type electrode 底氢型焊条low pressure scrubber 底压气净化器low stress round nosed die stam p 底应力圆头钢印lower deck 下甲板lub oil drain tank 润滑油排放罐lub oil tank with heater 润滑油罐（带加热器）lubricant oil transfer pum p 润滑油传输泵lug 吊耳Mm achinery deck 机械甲板m achining 机加工m acrosectin] 宏观断面m agnetic particle and suspension 磁粉和悬剂m agnetic particle technique 磁粉检验m agnetic particle techniuqe(MT) 磁粉探伤m ain boiler 主锅炉m ain deck 主甲板m ain generator set 主发电机组m ain process line 主要工艺管线m ain switch room 主变电间m ain transform er room 主变压器室m ake-up drawing 造管图m anhole 人孔m anifold 管汇m anned platform 驻人平台m anual / hand welding 手工焊m anufacture's instruction 产品使用说明m arine growth 海生物m arine radio system 海事通讯系统m arine transportation 海运m arking 做标记，划线m arking and cutting 划线下料m at support jack-up rig 沉垫自升式钻井船m aterial 材质，材料m aterial identification 材料标识m aterial list 材料表m aterial storage 材料储存m aterial substitution 材料代用m aterial take off 材料估算单m aterial traceability 材料跟踪m axim un iperating water depth 最大工作水深m ay 可以（任意性的）m ean sea level(MSL) 平均海平面m echanical property 机械性能m echanical test 机械性能试验m edium pressure separator (MP separator) 中压分离器m em ber 杆件m em ber drawing （杆件的）单件图m em ber num ber 杆件号m etacenter 稳心m etal lash 钢板网m ezzanine deck 夹层甲板，半甲middle deck 中甲板mild steel 底碳钢mill 钢厂mill certificate 厂家的材质证书mill scale 钢材出厂时的表面氧化皮mill sheet 制造工艺规程表mineral slag 矿渣miscellaneous item s 附件mism atch = high-low 错皮m obile drilling platform / rig 移动式钻井平台m obile radio system 移动式无线电系统m odel test 模型试验m odule 组块m old 模具m old lofting 放样m om ent 力矩m om ent of inertia 惯性矩m om ent of longitudinal inclination 纵倾力矩m om ent of transverse inclination 横倾力矩m ooring bit 系缆柱m ooring cable 系泊缆绳m ooring dolphin 系缆柱m ooring head 系泊头m ooring tem plate 系泊基盘m ooring yoke 系泊刚臂m otor operated valve 电动阀m ove to yard front 移至码头前沿m udline 泥线m udm at 防沉板m ultihead m etering pum p 多头计量泵m ultipass welding 多层焊m ultiple lift 多台吊车联合起吊m ulti-point m ooring,spread m ooring 多浮筒系泊系统m ulti-purpose epoxy 多用途环氧漆m ulti-supported beam 连续梁m ulti-well tem plate system 多井基盘系统Nnavigational light导航灯NC(num erical-control) cutting m achine数控切管机near white m etal接近金属白色needle valve 针阀nipple对丝node can接点段nominal diam eter公称直径non-com bustible不可燃物质non-conform ance不一致事项nondestructive exam ination(NDE) 无损检验nondestructive testing 无损检验nonskid ceram ic m osaic 外观检验norm al practice 通常作法norm alize 正火norm ally open /close valve 常开／常闭阀notch toughness 缺口韧性NRL(naval research laboratory) drop weight test NRL落锤试验nut 螺母GOD2009-02-11 02:35 Oobsolete docum ent 作废文件oceanographic research vessel 海洋调查船offshore drilling installation 海上钻井设备offshore drilling rig 海上钻井装置offshore hook-up 海上连接offshore installation 海上安装offshore installation site 海上安装现场offshore oil exploration 海洋石油勘探offshore platform 海洋平台offshore structure 海洋结构物oil boom, oil fence 围油栅oil concentration （污水）含油浓度oil depot 油库oil fence reel 围油栅卷筒oil m oisture content 油雾含量oil pollution 石油污染oil recovery vessel 污油回收船oil spill 溢油oil storage ,loading and transportation equipm ent 储油、装油与输油设备oil storage barge 储油轮oil treatm ent facility 油处理设施oil water transfer pum p 污油水传送泵oily water tank 含油污水仓one-line diagram 单线图onshore fabrication 陆上预制open drain pum p 开式排放泵open drain tank 开式排放罐open drain tank with heater 开式排放罐（带加热器）open firing point 明火点operating condition 作业条件operating state 作业状态operation draft 作业吃水orifice plate 孔板流量计original 原稿out of roundness 椭圆度outside diam eter(OD) 外径ovality 椭圆度over coating intervals 复涂间隔over head crane 天车吊overboard 舷外overhanging beam 悬臂梁overhead position welding 仰脸焊overhead welding 仰脸焊overlap 焊瘤overlapping joint 搭接节点owner 业主Oxyacetylene gas welding 氧－乙炔气焊oxyacetylene welding 氧乙炔焊oxygen cylinder 氧气瓶oxygen hose 氧气带Ppackaged air conditioner 空调机撬块packer 封隔器padeye 吊点paint brush 油刷子paint roller 油漆滚子painter 油漆工panel assem bling 平面组对，单片组对parasitic echo 干扰回声parent steel 母材past successful practice 以往成功的作法pedestal crane 基座式吊机pedestal crane 平台用吊机peening 捶击penetrant technique 渗透检验penetrant technique(PT) 渗透检验perim eter 周长periodical survey 定期检验permissible stress 许用应力perpendicularity of pipe end 管端垂直度personnel protection 人身保护phenolic paint 酚醛树脂涂料Philips driver 十字螺丝刀phthali c paint 苯二甲酸涂料pig launcher 清管器发射器pig receiver 清管接受器pile cap 桩帽pile driving records 打桩纪录pile driving refusal 拒锤点pile extracting 拔桩pile foundation 桩基pile guide 桩导向pile penetration 桩的贯入度pile section / segm ent 桩段pile sleeve 桩套筒pile spacer 扶桩间隙块pile washing out 冲桩piling 打桩piling barge 打桩船pilot house 驾驶室pinhole 针尖状气孔pipe diam eter 管径pipe fitting 管件pipe rack 管子托架pipe shoe 管子支撑pipe wrench 管钳pipeline 管线、管道pipeline laying barge 铺管船piping and instrum ent diagram(P&ID) 管线仪表图plain end 无螺纹管端plan 平面图、布置图plasm a arc cutting(PAC) 等离子弧切割plasm a arc welding(PAW) 等离子弧焊接plate girder 板梁plate type heat ex changer 板式换热器platform 平台platform positioning on the site 导管架的现场定位platform -to-shore radio system 平台--海岸无线电系统pliers 钳子plug 丝堵plug valve 旋塞阀plumm ent 铅坠plus or m inus 2 正负2pneum atic binary signal 双向气动信号pneum atic lines 气控管线pneum atic operated valve 气动操作阀pneum atic operated with m anual reset valve 手动复位气动阀pneum atic test 气压试验polarization potential （阳极的）极化电位polarization steel 极化铁polyurethane paint 聚氨酯涂料porosity 密集气孔port 左舷port hole 舷窗portable ex tinguisher 手提式灭火器portable two-way radio 双向无线电话positioner 定位器positioning 定位positive displacem ent flow m eter 容积式流量计positive flow m eter 正位流量计postweld heat treatm ent 焊后热处理pot life （油漆的）混合期限power wire bruch 电动钢丝刷preheat tem perature 预热温度preheater 预热器pressure differential flow m eter 差压流量计pressure gauge 压力表pressure regulation valve 压力调节阀pressure regulator(ex ternal tap) 压力调节阀（阀外引压）pressure relief valve 压力释放阀pressure safety valve 压力安全阀pressure vessels 压力容器prim ary structrural m em ber 主结构杆probe 探头procedure qualification record(PQR) 焊接工艺评定。

船舶与海洋工程专业常用词汇英汉对照汇总

IMO(Intergovernmental Maritime Organization)国际海事组织IMCO(Intergovernmental Maritime Consultative Organization)国际海事质询组织International Towing Tank Conference (ITTC) 国际船模试验水池会议International Association of Classification Society (IACS) 国际船级社协会ABS(American Bureau of Shipping) 美国船级社BV(Bureau Veritas) 法国船级社Lloyd's Register of shipping 英国劳埃德船级社RINA(Registo Italiano Navade) 意大利船级社Load Line Convention 载重线公约Lloyd's Rules 劳埃德规范Register （船舶）登录簿，船名录Green Book 绿皮书，19世纪英国另一船级社的船名录，现合并与劳埃德船级社，用于登录快速远洋船Supervision of the Society's surveyor 船级社验船师的监造书Merchant Shipbuilding Return 商船建造统计表BSRA 英国船舶研究协会HMS 英国皇家海军舰艇CAD(computer-aided design) 计算机辅助设计CAE(computer-aided manufacturing) 计算机辅助制造CAM(computer-aided engineering) 计算机辅助工程CAPP(computer -aided process planning) 计算机辅助施工计划制定IAGG(interactive computer graphics) 交互式计算机图像技术a faired set of lines 经过光顺处理的一套型线a stereo pair of photographs 一对立体投影相片abaft 朝向船体abandonment cost 船舶废置成本费用accommodation 居住（舱室）accommodation ladder 舷梯adjust valve 调节阀adjustable-pitch 可调螺距式admiralty 海军部advance coefficient 进速系数aerostatic 空气静力学的aft peak bulkhead 艉尖舱壁aft peak tank 艉尖舱aileron 副鳍air cushion vehicle 气垫船air diffuser 空气扩散器air intake 进气口aircraft carrier 航空母舰air-driven water pump 气动水泵airfoil 气翼，翼剖面，机面，方向舵alignment chock 组装校准用垫楔aluminum alloy structure 铝合金结构amidships 舯amphibious 两栖的anchor arm 锚臂anchor chain 锚链anchor crown 锚冠anchor fluke 锚爪anchor mouth 锚唇anchor recess锚穴anchor shackle 锚卸扣anchor stock 锚杆angle bar/plate 角钢angle of attack 攻角angled deck 斜角甲板anticipated loads encountered at sea 在波浪中遭遇到的预期载荷anti-pitching fins 减纵摇鳍antiroll fins 减摇鳍anti-rolling tank 减摇水舱appendage 附体artisan 技工assembly line 装配流水线at-sea replenishment 海上补给augment of resistance 阻力增额auxiliary systems 辅机系统auxiliary tank 调节水舱axial advance 轴向进速backing structure 垫衬结构back-up member 焊接垫板balance weight 平衡锤ball bearing 滚珠轴承ball valve 球阀ballast tank 压载水舱bar 型材bar keel 棒龙骨，方龙骨，矩形龙骨barge 驳船base line 基线basic design 基本设计batten 压条，板条beam 船宽，梁beam bracket 横梁肘板爱beam knee 横梁肘板bearing 轴承bed-plate girder 基座纵桁bending-moment curves 弯矩曲线Benoulli's law 伯努利定律berth term 停泊期bevel 折角bidder 投标人bilge 舭，舱底bilge bracket 舭肘板bilge radius 舭半径bilge sounding pipe 舭部边舱水深探管bitt 单柱系缆桩blade root 叶跟blade section 叶元剖面blast 喷丸block coefficient 方形系数blue peter 出航旗boarding deck 登艇甲板boat davit 吊艇架boat fall 吊艇索boat guy 稳艇索bobstay 首斜尾拉索body plan 横剖面图bolt 螺栓，上螺栓固定Bonjean curve 邦戎曲线boom 吊杆boss 螺旋桨轴榖bottom side girder 旁底桁bottom side tank 底边舱bottom transverse 底列板boundary layer 边界层bow line 前体纵剖线bow wave 艏波bowsprit 艏斜桅bow-thruster 艏侧推器box girder 箱桁bracket floor 框架肋板brake 制动装置brake band 制动带brake crank arm 制动曲柄brake drum 刹车卷筒brake hydraulic cylinder 制动液压缸brake hydraulic pipe 刹车液压管breadth extreme 最大宽，计算宽度breadth moulded 型宽breakbulk 件杂货breasthook 艏肘板bridge 桥楼，驾驶台bridge console stand 驾驶室集中操作台buckle 屈曲buffer spring 缓冲弹簧built-up plate section 组合型材bulb plate 球头扁钢bulbous bow 球状船艏，球鼻首bulk carrier 散货船bulk oil carrier 散装油轮bulkhead 舱壁bulwark 舷墙bulwark plate 舷墙板bulwark stay 舷墙支撑buoy tender 航标船buoyant 浮力的buoyant box 浮箱butt weld 对缝焊接butterfly screw cap 蝶形螺帽buttock 后体纵剖线by convention 按照惯例，按约定cable ship 布缆船cable winch 钢索绞车camber 梁拱cant beam 斜横梁cant frame 斜肋骨cantilever beam 悬臂梁capacity plan 舱容图capsize 倾覆capsizing moment 倾覆力臂captain 船长captured-air-bubble vehicle 束缚气泡减阻船cargo cubic 货舱舱容，载货容积cargo handling 货物装卸carriage 拖车，拖架cast steel stem post 铸钢艏柱catamaran 高速双体船，双体的cavitation 空泡cavitation number 空泡数cavitation tunnel 空泡水筒center keelson 中内龙骨centerline bulkhead 中纵舱壁centroid 型心，重心，质心，矩心chain cable stopper 制链器chart 海图charterer 租船人chief engineer 轮机长chine 舭，舷，脊chock 导览钳CIM(computer integrated manufacturing) 计算机集成组合制造circulation theory 环流理论classification society 船级社cleat 系缆扣clipper bow 飞剪型船首clutch 离合器coastal cargo 沿海客货轮cofferdam 防撞舱壁combined cast and rolled stem 混合型艏柱commercial ship 营利用船commissary spaces 补给库舱室，粮食库common carrier 通用运输船commuter 交通船compartment 舱室compass 罗经concept design 概念设计connecting tank 连接水柜constant-pitch propeller 定螺距螺旋桨constraint condition 约束条件container 集装箱containerized 集装箱化contract design 合同设计contra-rotating propellers 对转桨controllable-pitch 可控螺距式corrosion 锈蚀，腐蚀couple 力矩，力偶crane 克令吊，起重机crank 曲柄crest (of wave) 波峰crew quarters 船员居住舱criterion 判据，准则Critical Path Method 关键路径法cross-channel automobile ferries 横越海峡车客渡轮cross-sectional area 横剖面面积crow's nest 桅杆瞭望台cruiser stern 巡洋舰尾crussing range 航程cup and ball joint 球窝关节curvature 曲率curves of form 各船形曲线cushion of air 气垫damage stability 破损稳性damper 缓冲器damping 阻尼davit arm 吊臂deadweight 总载重量de-ballast 卸除压载deck line at side 甲板边线deck longitudinal 甲板纵骨deck stringer 甲板边板deck transverse 强横梁deckhouse 舱面室，甲板室deep v hull 深v型船体delivery 交船depth 船深derrick 起重机，吊杆design margin 设计余量)design spiral 设计螺旋循环方式destroyer 驱逐舰detachable shackle 散合式连接卸扣detail design 详细设计diagonal stiffener 斜置加强筋diagram 图，原理图，设计图diesel engine 柴油机dimensionless ratio 无量纲比值displacement 排水量displacement type vessel 排水型船distributed load 分布载荷division 站，划分，分隔do work 做功dock 泊靠double hook 山字钩double iteration procedure 双重迭代法double roller chock 双滚轮式导览钳double-acting steam cylinder 双向作用的蒸汽气缸down halyard 降帆索draft 吃水drag 阻力，拖拽力drainage 排水draught 吃水，草图，设计图，牵引力爱dredge 挖泥船drift 漂移，偏航drilling rig 钻架drill ship 钻井船drive shaft 驱动器轴driving gear box 传动齿轮箱driving shaft system 传动轴系dry dock 干船坞ducted propeller 导管螺旋桨dynamic supported craft 动力支撑型船舶dynamometer 测力计，功率计e.h.p 有效马力eccentric wheel 偏心轮echo-sounder 回声探深仪eddy 漩涡eddy-making resistance 漩涡阻力efficiency 供给能力，供给量electrohydraulic 电动液压的electroplater 电镀工elevations 高度，高程，船型线图的侧面图，立视图，纵剖线图，海拔empirical formula 经验公式enclosed fabrication shop 封闭式装配车间enclosed lifeboat 封闭式救生艇end open link 末端链环end shackle 末端卸扣endurance 续航力，全功率工作时间engine room frame 机舱肋骨engine room hatch end beam 机舱口端梁ensign staff 船尾旗杆entrance 进流段erection 装配，安装exhaust valve 排气阀expanded bracket 延伸肘板expansion joint 伸缩接头extrapolate 外插fair 光顺faised floor 升高肋板fan 鼓风机fatigue 疲劳feasibility study 可行性研究feathering blade 顺流变距桨叶fender 护舷ferry 渡轮，渡运航线fillet weld connection 贴角焊连接fin angle feedback set 鳍角反馈装置fine fast ship 纤细高速船fine form 瘦长船型finite element 有限元fire tube boiler 水火管锅炉fixed-pitch 固定螺距式flange 突边，法兰盘flanking rudders 侧翼舵flap-type rudder 襟翼舵flare 外飘，外张flat of keel 平板龙骨fleets of vessels 船队flexural 挠曲的floating crane 起重船floodable length curve 可进长度曲线flow of materials 物流flow pattern 流型，流线谱flush deck vessel 平甲板型船flying bridge 游艇驾驶台flying jib 艏三角帆folding batch cover 折叠式舱口盖folding retractable fin stabilizer 折叠收放式减摇鳍following edge 随边following ship 后续船foot brake 脚踏刹车fore peak 艏尖舱forged steel stem 锻钢艏柱forging 锻件，锻造forward draft mark 船首水尺forward/after perpendicular 艏/艉柱forward/after shoulder 前/后肩foundry casting 翻砂铸造frame 船肋骨，框架，桁架frame spacing 肋骨间距freeboard 干舷freeboard deck 干舷甲板freight rate 运费率fresh water loadline 淡水载重线frictional resistance 摩擦阻力Froude number 傅汝德数fuel/water supply vessel 油水供给船full form丰满船型full scale 全尺度fullness 丰满度funnel 烟囱furnishings 内装修gaff 纵帆斜桁爱gaff foresail 前桅主帆gangway 舷梯gantt chart 甘特图gasketed openings 装以密封垫的开口general arrangement 总布置general cargo ship 杂货船generatrix 母线geometrically similar form 外形相似船型girder 桁梁，桁架girder of foundation 基座纵桁governmental authorities 政府当局，管理机构gradient 梯度graving dock 槽式船坞gross ton 长吨（1.016公吨，short for GT）group technology 成组建造技术guided-missile cruiser 导弹巡洋舰gunwale 船舷上缘gunwale angle 舷边角钢gunwale rounded thick strake 舷边圆弧厚板guyline 定位索gypsy 链轮gyro-pilot steering indicator 自动操舵操纵台gyroscope 回转仪half breadth plan 半宽图half depth girder 半深纵骨half rounded flat plate 半圆扁钢hard chine 尖舭hatch beam sockets 舱口梁座hatch coaming 舱口围板hatch cover 舱口盖（板）hatch cover rack 舱口盖板隔架hatch side cantilever 舱口悬臂梁hawse pipe 锚链桶hawsehole 锚链孔heave 垂荡heel 横倾heel piece 艉柱根helicoidal 螺旋面的，螺旋状的hinge 铰链hinged stern door 艉部吊门hog 中拱hold 船舱homogeneous cylinder 均质柱状体hopper barge 倾卸驳horizontal stiffener 水平扶强材hub 桨毂，轴毂，套筒hull form 船型，船体外形hull girder stress 船体桁应力HV AC(heating ventilating and cooling) 取暖，通风与冷却hydraulic mechanism 液压机构hydrodynamic 水动力学的hydrofoil 水翼hydrostatic 水静力的icebreaker 破冰船immerse 浸水，浸没impact load 冲击载荷imperial unit 英制单位in strake 内列板inboard profile 纵剖面图incremental plasticity 增量塑性independent tank 独立舱柜initial stability at small angle of inclination 小倾角初稳性inland waterways vessel 内河船inner bottom 内底in-plane load 面内载荷intact stability 完整稳性intercostals 肋间的，加强的intersection 交点，交叉，横断（切）inventory control 存货管理iterative process 迭代过程jack 船首旗jack 千斤顶joinery 细木工keel 龙骨keel laying 开始船舶建造kenter shackle 双半式连接链环Kristen-Boeing propeller 正摆线推进器landing craft 登陆艇launch 发射，下水launch 汽艇launching equipment （向水中）投放设备leading edge 导缘，导边ledge 副梁材length overall 总长leveler 调平器，矫平机life saving appliance 救生设备lifebuoy 救生圈lifejacket 救生衣lift fan 升力风扇lift offsets 量取型值light load draft 空载吃水lightening hole 减轻孔light-ship 空船limbers board 舭部污水道顶板liner trade 定期班轮营运业lines 型线lines plan 型线图Linnean hierarchical taxonomy 林式等级式分类学liquefied gas carrier 液化气运输船liquefied natural gas carrier 液化天然气船liquefied petroleum gas carrier 液化石油气船liquid bulk cargo carrier 液体散货船liquid chemical tanker 液体化学品船living and utility spaces 居住与公用舱室load line regulations 载重线公约，规范load waterplane 载重水线面loft floor 放样台longitudinal (transverse) 纵（横）稳心高longitudinal bending 纵总弯曲longitudinal prismatic coefficient 纵向棱形系数longitudinal strength 总纵强度longitudinally framed system 纵骨架式结构luffing winch 变幅绞车machinery vendor 机械（主机）卖方magnet gantry 磁力式龙门maiden voyage 处女航main impeller 主推叶轮main shafting 主轴系major ship 大型船舶maneuverability 操纵性manhole 人孔margin plate 边板mark disk of speed adjusting 速度调整标度盘mast 桅杆mast clutch 桅座matrix 矩阵merchant ship 商船metacenter 稳心metacentric height 稳心高metal plate path 金属板电镀槽metal worker 金属工metric unit 公制单位middle line plane 中线面midship section 舯横剖面midship section coefficient 中横剖面系数ML 物资清单，物料表model tank 船模试验水池monitoring desk of main engine operation 主机操作监视台monitoring screen of screw working condition 螺旋桨运转监视屏more shape to the shell 船壳板的形状复杂mould loft 放样间multihull vessel 多体船multi-purpose carrier 多用途船multi-ship program 多种船型建造规划mushroom ventilator 蘑菇形通风桶mutually exclusive attribute 相互排它性的属性N/C 数值控制nautical mile 海里naval architecture 造船学navigation area 航区navigation deck 航海甲板near-universal gear 准万向舵机，准万向齿轮net-load curve 静载荷曲线neutral axis 中性轴，中和轴neutral equilibrium 中性平衡non-retractable fin stabilizer 不可收放式减摇鳍normal 法向的，正交的normal operating condition 常规运作状况nose cone 螺旋桨整流帽notch 开槽，开凹口oar 橹，桨oblique bitts 斜式双柱系缆桩ocean going ship 远洋船off-center loading 偏离中心的装载offsets 型值offshore drilling 离岸钻井offshore structure 离岸工程结构物oil filler 加油点oil skimmer 浮油回收船oil-rig 钻油架on-deck girder 甲板上桁架open water 敞水optimality criterion 最优性准则ore carrier 矿砂船orthogonal 矩形的orthogonal 正交的out strake 外列板outboard motor 舷外机outboard profile 侧视图outer jib 外首帆outfit 舾装outfitter 舾装工outrigger 舷外吊杆叉头overall stability 总体稳性overhang 外悬paddle 桨paddle-wheel-propelled 明轮推进的Panama Canal 巴拿马运河panting arrangement 强胸结构，抗拍击结构panting beam 强胸横梁panting stringer 抗拍击纵材parallel middle body 平行中体partial bulkhead 局部舱壁payload 有效载荷perpendicular 柱，垂直的，正交的photogrammetry 投影照相测量法pile driving barge 打桩船pillar 支柱pin jig 限位胎架pintle 销，枢轴pipe fitter 管装工pipe laying barge 铺管驳船piston 活塞pitch 螺距ipitch 纵摇plan views 设计图planning hull 滑行船体Plimsoll line 普林索尔载重线polar-exploration craft 极地考察船poop 尾楼port 左舷port call 沿途到港停靠positive righting moment 正扶正力矩power and lighting system 动力与照明系统precept 技术规则preliminary design 初步设计pressure coaming 阻力式舱口防水挡板principal dimensions 主尺度Program Evaluation and Review Technique 规划评估与复核法progressive flooding 累进进水project 探照灯propeller shaft bracket 尾轴架爱propeller type log 螺旋桨推进器测程仪PVC foamed plastic PVC泡沫塑料quadrant 舵柄quality assurance 质量保证quarter 居住区quarter pillar 舱内侧梁柱quartering sea 尾斜浪quasi-steady wave 准定长波quay 码头，停泊所quotation 报价单racking 倾斜，变形，船体扭转变形radiography X射线探伤rake 倾斜raked bow 前倾式船首raster 光栅refrigerated cargo ship 冷藏货物运输船regulating knob of fuel pressure 燃油压力调节钮reserve buoyancy 储备浮力residuary resistance 剩余阻力resultant 合力reverse frame 内底横骨Reynolds number 雷诺数right-handed propeller 右旋进桨righting arm 扶正力臂，恢复力臂rigid side walls 刚性侧壁rise of floor 底升riverine warfare vessel 内河舰艇rivet 铆接，铆钉roll 横摇roll-on/roll-off (Ro/Ro) 滚装rotary screw propeller 回转式螺旋推进器9 rounded gunwale 修圆的舷边rounded sheer strake 圆弧舷板rubber tile 橡皮瓦rudder 舵rudder bearing 舵承rudder blade 舵叶rudder control rod 操舵杆rudder gudgeon 舵钮rudder horn 挂舵臂rudder pintle 舵销rudder post 舵柱rudder spindle 舵轴rudder stock 舵杆rudder trunk 舵杆围井run 去流段sag 中垂salvage lifting vessel 救捞船scale 缩尺，尺度schedule coordination 生产规程协调schedule reviews 施工生产进度审核screen bulkhead 轻型舱壁Sea keeping performance 耐波性能sea spectra 海浪谱sea state 海况seakeeping 适航性seasickness 晕船seaworthness 适航性seaworthness 适航性section moulus 剖面模数section 剖面，横剖面self-induced 自身诱导的self-propulsion 自航semi-balanced rudder 半平衡舵semi-submersible drilling rig 半潜式钻井架shaft bossing 轴榖shaft bracket 轴支架shaft coupling 联轴节shear 剪切，剪力shear buckling 剪切性屈曲shear curve 剪力曲线sheer 舷弧sheer aft/forward 艉/艏舷弧sheer drawing 剖面图sheer plane 纵剖面sheer profile 总剖线，纵剖图shell plating 船壳板ship fitter 船舶装配工ship hydrodynamics 船舶水动力学shipway/slipway 船台shipyard 船厂shrouded screw 有套罩螺旋桨，导管螺旋桨side frame 舷边肋骨side keelson 旁内龙骨side plate 舷侧外板side stringer 甲板边板single-cylinder engine 单缸引擎sinkage 升沉six degrees of freedom 六自由度skin friction 表面摩擦力skirt （气垫船）围裙slamming 砰击sleeve 套管，套筒，套环slewing hydraulic motor 回转液压马达slice 一部分，薄片sloping shipway 有坡度船台sloping top plate of bottom side tank 底边舱斜顶板sloping bottom plate of topside tank 顶边舱斜底板soft chine 圆舭sonar 声纳spade rudder 悬挂舵spectacle frame 眼睛型骨架speed-to-length ratio 速长比sponson deck 舷伸甲板springing 颤振stability 稳性stable equilibrium 稳定平衡starboard 右舷static equilibrium 静平衡steamer 汽轮船steering gear 操纵装置，舵机stem 船艏stem contour 艏柱型线stern 船艉stern barrel 尾拖网滚筒stern counter 尾突体stern ramp 尾滑道，尾跳板爱stern transom plate 尾封板stern wave 艉波stiffen 加劲，加强stiffener 扶强材，加劲杆straddle 跨立，外包式叶片strain 应变strake 船体列板streamline 流线streamlined casing 流线型套管strength curves 强度曲线strength deck 强力甲板stress concentration 应力集中structural instability 结构不稳定性strut 支柱，支撑构型subassembly 分部装配subdivision 分舱submerged nozzle 浸没式喷口submersible 潜期suction back of a blade 桨叶片抽吸叶背Suez Canal tonnage 苏伊士运河吨位限制summer load water line 夏季载重水线superintendent 监督管理人，总段长，车间主任superstructure 上层建筑supper cavitating propeller 超空泡螺旋桨surface nozzle 水面式喷口surface piercing 穿透水面的surface preparation and coating 表面预处理与喷涂surge 纵荡sway 横荡yaw 首摇surmount 顶上覆盖，越过swage plate 压筋板swash bulkhead 止荡舱壁SWATH (Small Waterplane Area Twin Hull) 小水线面双体船tail-stabilizer anchor 尾翼式锚talking paper 讨论文件tangential 切向的，正切的tangential viscous force 切向粘性力tanker 油船tender 交通小艇timber carrier 木材运输船tugboat 拖船tee T型构件，三通管tensile stress 拉（张）应力thermal effect 热效应throttle valve 节流阀throughput 物料流量thrust 推力thruster 推力器，助推器tip of a blade 桨叶叶梢toed towards amidships 趾部朝向船舯tonnage 吨位torpedo 鱼雷torque 扭矩trailing edge 随边transom stern 方尾transverse bulkhead plating 横隔舱壁板transverse section 横剖面transverse stability 横稳性trawling 拖网trial 实船试验trim 纵倾trim by the stern/bow 艉/艏倾trimaran 三体的tripping bracket 防倾肘板trough 波谷tumble home （船侧）内倾tunnel wall effect 水桶壁面效应turnable blade 可转动式桨叶turnable shrouded screw 转动导管螺旋桨tweendeck cargo space 甲板间舱tweendedk frame 甲板间肋骨two nodded frequency 双节点频率LCC 大型原油轮ULCC 超级大型原油轮VLCC 巨型原油轮ultrasonic 超声波的underwriter （海运）保险商unsymmetrical 非对称的upright position 正浮位置vapor pocket 气化阱ventilation and air conditioning diagram 通风与空调铺设设计图Venturi section 文丘里试验段vertical prismatic coefficient 横剖面系数vertical-axis(cycloidal)propeller 直叶（摆线）推进器vessel component vender 造船部件销售商viscosity 粘性V oith-Schneider propeller 外摆线直翼式推进器vortex 梢涡v-section v型剖面wake current 伴流，尾流water jet 喷水（推进）管water plane 水线面watertight integrity 水密完整性wave pattern 波形wave suppressor 消波器，消波板wave-making resistance 兴波阻力weather deck 露天甲板web 腹板web beam 强横梁web frame 腹肋板welder 焊工wetted surface 湿表面积winch 绞车windlass 起锚机wing shaft 侧轴wing-keel 翅龙骨（游艇）working allowance 有效使用修正量worm gear 蜗轮，蜗杆yacht 快艇yard issue 船厂开工任务发布书yards 帆桁--。

船舶工程专业英语

目录一、造船部分1、船体部分2、机舱部分3、电气部分4、船装部分二、造机部分三、修造部分一、造船部分1、HULL PART 船体部分1、1 结构Structure船厂dockyard/shipyard 船坞dock/boatyard船东ship-owner 船舷Ship's side船码头quay/dock 船的栏杆Ship's rail船舱hold 甲板Deck船籍Ship's registry 住舱甲板accommodation deck船首bow 梁拱甲板arch deck船梯ladder 载货甲板cargo deck船尾stern 首楼甲板Forecastle deck上甲板Upper deck下甲板Lower deck主甲板Main deck货舱甲板Hold deck桥楼甲板Bridge deck水密甲板Watertight deck驾驶甲板Navigation deck 铜-钢复合板Copper sheathing steel plate 艇甲板Boat deck 甲板边板Deck stringer plate罗经甲板Compass deck 斜板Sloping plate板Plate 加强板Reinforcement plate舭板Bilge plate 舵板Rudder plate船底板Bottom plate 舷侧外板Side plate船外板Shell plate 裙板Skirt plate船首外板Bow plate 首柱板Stem plate肘板Bracket plate 首柱板Stern plate舱壁板Bulkhead plate 平台platform槽形舱壁板Corrugated bulkhead plate 机舱平台Engine-room platform 舷墙板Bulwark plate 分段Block围板Coaming plate 首段Bow block连续板Connection plate 中段Midship block尾段Stern block 甲板下纵桁Underdeck girder左舷port 舭纵桁Wing girder右舷Starboard 支柱Pillar纵桁Girder 肋骨Frame型材桁Bar girder 基础台架Base frame中底桁Bottom center girder 支架Bear frame中内龙骨Bottom center line girder 舭肋骨Bilge frame底桁材Bottom girder 船底肋骨Bottom frame旁桁材Bottom side girder 首肋骨Bow frame甲板纵桁Deck girder 肘板框架肋骨Bracket frame横桁Cross girder 球鼻首肋骨Bulbous bow frame水平桁Horizontal girder 球曲型肋骨Bulbous frame舱口边梁Hatch coaming girder 主肋骨Chief frame机座纵桁Engine girder 首肋骨Fore frame桁架梁Girder frame 舭纵桁舭纵骨Bilge longitudinal舯部肋骨Middle frame 船底纵骨/纵桁bottom longitudinal尖舱肋骨Peak frame 船底腹板纵桁bottom web longitudinal加强筋Stiffened frame 甲板纵桁Deck longitudinal横框架肋骨Transverse frame 内底纵桁/纵骨Inner bottom longitudinal肋距 F.S.(frame space) 舷侧纵桁/纵骨Shell side longitudinal纵桁/纵骨/纵向构件longitudinal双层底顶纵骨Top longitudinal of double bottom斜舱壁纵骨Slopping-bulkhead longitudinal舱舷边舱Tank Wing tank结构structure 尾尖舱after peak tank附属结构Accessory structure 尾部水舱after water tank全焊结构All-welded structure 辅助水柜Auxiliary water tank中部结构Amidships structure 辅助压载水舱Auxiliary water ballast tank 泊位结构Berthing structure 污水舱Bilge tank底部龙骨结构Bottom keel structure 底舱Bottom tank船首部结构Bow structure 底边舱Bottom side tank支撑结构Braced structure 货油压载舱Cargo and ballast tank桥楼结构Bridge structure 循环水槽Circulating flow water tank首楼结构Forecastle structure 循环滑油舱压载水舱Circulating lubricating oil tank Ballast water tank构架结构Framed structure 清洁压载舱Clean ballast tank纵桁结构Girder structure 冷凝水柜Condensate catch tank人孔manhole 干舱Dry tank饮用水舱Drinking water tank 密封圈Sealing ring污水舱Bilge tank 铰链Hinge应急淡水柜Emergency fresh water tank 把手Handle首舱Fore tank 平衡块Balance block首尖舱Fore peak tank斜边舱Hopper side tank 1、2 welding 焊接液舱Liquid tank 坡口groove龙骨舱Keel tank 单面坡口Single groove右舷舱Starboard tank 双面坡口Double groove顶边水舱Topside tank Ⅰ形坡口Square groove顶边翼舱Topside wing tank V 型坡口Single v groove小舱口盖Small hatch cover U 型坡口Single u groove水密舱口盖Water-tight small hatch coverX 形坡口Single v groove风雨密舱口盖Weather-tight small hatch coverK 形坡口Single bevel grooveY 形坡口Single v groove with broad rood face填充金属Filler metal坡口面Groove face 热影响区Heat-affected zone(HAZ)坡口角度Groove angle 过热区Overheated zone焊缝倾角Weld slope 焊合线Bond line(fusion line)接头根部Root of joint 焊接区Weld zone根部间隙Root gap 焊缝区Weld metal area钝边Root face 焊缝weld焊接接头Welding joint 连续焊缝Continuous weld对接接头Butt joint 断续焊缝Intermittent weld角接接头Corner joint 纵向焊缝Longitudinal weldT 形接头T-joint 横向焊缝Transverse weld搭接接头Lap joint 对接焊缝隙Butt weld十字接头Cross shaped joint 角焊缝Filled weld母材Base metal(parent metal) 并列断续角焊缝Chain intermittent fillet交错断续角焊缝Staggered intermittent fillet弧焊整流器Arc welding rectifier焊缝正面Face of weld 自动焊Automatic welding焊缝背面Back of weld 埋弧自动焊Submerged arc welding焊缝宽度Weld width 半自动焊Semi- automatic welding焊缝长度Weld length 氩弧焊Argon-arc welding焊缝余高Reinforcement 二氧化碳气体保护焊CO2 gas shielded arc welding 焊脚Leg(of a fillet weld) 氧乙炔焊Oxy-acetylene welding焊脚长度Leg length 气割Gas cutting套管接头Muff joint 碳弧气刨Carbon arc air gouging手工电弧焊Manual arc welding(shielded metal arc welding)水下切割Underwater cutting直流电弧焊Direct current arc welding 等离子弧切割Plasma arc cutting 交流电弧焊alternating current arc welding连续焊Continuous welding弧焊变压器Arc welding transformer 断续焊Intermittent welding点焊Sport welding对接焊Butt welding 分段退焊Back step welding角焊Fillet welding 分段多层焊Block welding搭接焊Lap welding 深溶焊Deep penetrating welding返修焊Re-welding 跳焊Skip welding补焊Repair welding 陶质衬垫焊Ceramic backing welding定位焊Tack welding 引弧Striking the arc封底焊Back sealing welding 焊接工艺参数Welding condition打底焊Backing welding 焊接电流Welding current堆焊Surfacing(overlaying) 焊接电压Welding voltage塞焊Plug welding 焊接速度Welding speed槽焊Slot welding 电弧电压Arc voltage盖面焊Consmetic welding 焊丝间距Wire spacing前倾焊Forward welding 空载电压Open circuit voltage后倾焊Backward welding 熔化速度Melting rate送丝速度Wire feed rate 层间温度Inter-pass temperature气体流量Gas flow rate 焊后热处理Post-weld heat treatment焊丝伸出长度Wire extension 锤击Peening极性Polarity 全焊透Full penetration welding正极/阳极Positive electrode 熔池Weld-pool负极/阴极Navigate electrode 熔深Penetration左焊法Leftward welding 弧长Arc length右焊法Rightward welding 喷射过渡Spray transfer电流密度Current density 短路过渡Short circuiting transfer线能量Heat input 熔滴过渡Metal transfer预热Preheat 焊缝成形Appearance of weld后热Post-heat 焊缝成形系数Form factor of weld预热温度Preheat temperature 熔敷系数Deposition coeffcient后热温度Post-heat temperature 熔敷效率Deposition efficiency熔合比Penetration ratio 立焊Vertical position welding等速送丝Constant wire-feed system 仰焊Overhead position welding 变速送丝alternate wire-feed system 立向上焊Vertical up welding 电弧静特性Static characteristic of arc立向下焊Vertical down welding电弧动特性dynamic characteristic of arc单面焊Welding by one side焊接性试验Weldability test 双面焊Welding by both side焊接结构Welded construction 单道焊Single-pass welding焊道Bead 多道焊Multi-pass welding焊层Layer 多层焊Multi-layer welding正接（正极性）Straight polarity 焊接材料Consumables反接（反极性）Reversed polarity 焊条Electrode焊接位置Position of welding 焊条药皮Coating平焊Flat position welding 酸性焊条Acid electrode横焊Horizontal position welding 碱性焊条Basic electrode低氢型焊条Low hydrogen type electrode 焊丝盘Wire reel铁粉性焊条Iron power type electrode 铜冷却板Cu-cooling plate重力焊条Gravity electrode 铜滑块Copper shoe焊剂Flux 切割Cutting熔炼焊剂Fused flux 焊接工作台Welding bench烧结焊剂Sintered flux 焊接变位机Positioner焊丝Wire 送丝机构Wire feeder药芯焊剂Flux-cored wire 行走机构Traveler保护气体Shielded gas 焊接车间Welding shop焊剂垫Flux backing 引弧板Run-on tab(end tab)重力焊条Gravity electrode 引出板Run-off tab(end tab)焊剂漏斗Flux-hopper 定位板Strong-back流量计Flow meter 焊接衬垫Welding backing干燥箱Dryer 敲渣锤Chipping hammer面罩Helmet 条虫状气孔Wormhole焊工手套Welding glove 密集气孔Porosity焊钳Electrode holder 针尖状气孔Pinhole焊枪Welding gun 白点Fish eye (flake)导电嘴Tip 切口Kerf喷嘴Nozzle 咬边Undercut焊矩Torch 焊瘤overlap焊接缺陷Welding defect 凹坑Pit未焊透Incomplete penetration 烧穿Burn through未熔合Incomplete fusion 未满焊Incomplete filled groove渣Slag 清根Back chipping夹渣Slag (slag inclusion) 清渣Slag removal夹杂物Inclusion 焊接烟尘Weld fume气孔Blow hole 电光性眼炎Eye-flash焊接性Weldability 横裂纹Transverse crack碳当量Carbon equivalent 纵裂纹Longitudinal crack未焊满Incomplete filled groove 焊趾裂纹Toe crack焊接裂纹Weld crack 机械性能试验Mechanical property test 热裂纹Hot crack 试板Test piece冷裂纹Cold crack 试样Specimen氢致裂纹Hydrogen –induced crack 侧弯Side bend延迟裂纹Delayed crack 弯曲Bending层状撕裂Lemellar tearing 横向拉伸Transverse tensile弧坑裂纹Crater crack 宏观试样Macro-etching specimen根部裂纹Root crack 微观试样Micro-examination specimen再热裂纹Reheat crack 破断试验Fracture test热影响区裂纹Heat-effected zone crack 抗裂试验Cracking test晶间裂纹Intercystalline crack 脆性断裂Brittle fracture塑性断裂Plastic fracture 焊接方法Welding process焊接残余裂纹Welding residual stress 焊接工艺Welding technology消除应力Stress relieving 焊接操作Welding operation焊接变形Welding deformation 焊接顺序Welding sequence角变形Angular distortion 焊接方向Direction of welding外观检查Visual examination 常用缩语无损探伤Non-destruction testing(N.D.T.)气电立焊EGW超声波探伤Ultrasonic inspection 药芯电弧焊FCAW射线探伤（X 光）Radiographic inspection(X-rayinspection)实心电弧焊GMAW磁粉探险伤Magnetic particle inspection焊剂铜衬垫单面埋弧自动焊FCB渗透探伤Penetrate inspection 手工电弧焊SMAW熔池Weld-pool 埋弧自动焊SAW焊机（焊接电源）Weld source钨极惰性气体保护电弧焊TIG 机舱部分ENGINE ROOM PART熔化极惰性气体保护焊MIG 一、机舱设备Machines and equipment in engine room 活性气体保护焊MAG 1、主机Main engine手工电弧切割SMAC 1）主机油底壳The sump tank of M.E.2）主机飞轮Fly wheel of M.E3）活塞Piston2、发电机Generator engine1）应急发电机Emergency generator engine2）辅机Auxiliary3、锅炉Boiler1）组合锅炉The composite boiler2）锅炉安全阀The safety valve of boiler3）燃烧器Oil burner unit 3）主空气瓶Main air reservoir4）水位表Water level gauge 4）应急空气瓶Emergency air reservoir5）水位控制器Water level controller 5、控制空气瓶Control air reservoir 6）过量蒸气调节阀Excess steam pressure control valve6、空气干燥器Air dryer4、舵机7、分油机Oil purifier1）舵机间Steering room 1）燃油分油机Fuel oil purifier2）舵机装置Steering-gear 2）柴油分油机Diesel oil purifier3）手操舵装置Trick wheel plant 3）滑油分油机Lubricate oil purifier 4）油缸Oil cylinder 4）排渣Sludge discharge5）反馈装置Feedback device 8、制淡装置Fresh water generator6）舵Rudder9、焚烧炉Incinerator舵叶Rudder blade10、油水分离器Oil water separator舵杆Rudder stock11、生活污水处理器Sewage treat plant上舵承Rudder carrier12、大气冷凝器Atmosphere condenser热水井Cascade and inspection(hotwell)5）主机燃油供给泵Main engine fuel oil supply pump滑油自清滤器The automatic back-flashlubricating oil filter6）主机燃油增压泵Main engine fuel oil booster pump燃油单元Fuel oil unit 7）主机十字头泵Main engine cross head pump1）主机燃油单元Fuel oil unit of M.E 8）付机海水泵Generator engine sea water pump2）付机燃油单元Fuel oil unit of A.E 9）付机缸套水泵Generator engine cylinder cooling water pump 3）粘度计Viscosity controller 10）锅炉给水泵Feed water pump of boiler泵Pump 11）锅炉燃油泵Fuel oil pump of boiler1）主机滑油泵Main engine lubricating oil pump12）分油机供给泵Fuel oil supply pump of purifier2）主机缸套水泵Main engine cylinder cooling water pump13）制淡海水泵Sea water pump of fresh water generator3）主机缸套水预热泵Main engine cylinder cooling water preheating pump14）压载泵Ballast pump4）主机海水泵Main engine sea water pump 15）舱底消防泵Bilge and fire pump17）油渣泵Sludge oil pump 2、柴油澄清舱Diesel oil setting tank18）柴油输送泵Diesel oil transport pump 3、燃油日用柜Fuel oil daily tank19）燃油油输送泵Fuel oil transport pump 4、燃油澄清舱Fuel oil setting tank20）汽缸油输送泵Cylinder oil transport pump 5、滑油澄清舱Lubricating oil setting tank21）淡水输送泵Fresh water transport pump 6、滑油储藏舱Lubricating oil store tank22）热水循环泵Hot water circulating pump 7、滑油循环舱Lubricating oil circulating tank23）饮水日用泵Drinking water pump 8、燃油溢油舱Fuel oil overflow tank舱底消防总用泵Bilge, fire and G.S pump 9、燃油油渣舱Fuel oil sludge tank喷淋泵Sprinkling pump 10 燃油深舱Fuel oil deep tank停泊海水泵Harbor sea water pump 11 滑油污油舱Lubricating dirty oil tank12 滑油溢油舱Lubricating oil overflow tank二、各种舱（箱）柜All kinds of tank 13 滑油油渣打舱Lubricating oil sludge tank1、柴油日用柜Diesel oil daily tank 14 主机淡水膨胀水箱M.E fresh water expansion tank15 付机淡水膨胀水箱A.E fresh water expansion tank16、淡水压力柜Fresh water pressure tank 1、滑油系统Lubricating oil piping system17、热水压力柜Hot water pressure tank 2、燃油系统Fuel oil piping system18、饮水压力柜Drinking water pressure tank3、海水系统Sea water piping system19、淡水舱Fresh water tank 4、缸套水系统Cylinder cooling water piping system20、饮水舱Drinking water tank 5、启动空气系统Start air piping system21、锅炉水舱Boiler water tank 6、控制空气系统Control air piping system22、分油机工作水箱Purify operating water tank 7、排气系统Exhaust piping system23、汽缸油日用柜Cylinder oil daily tank 8、日用供水系统Daily water piping system24、尾管滑油重力柜Gravity tank of tube oil 9、蒸汽系统Steam piping system25、排气水封箱Exhaust seal water tank 10 、锅炉给水和凝水系统Feed water and condensate of boiler piping system26、蒸馏水水舱Distilling water tank 11、燃油净油系统Fuel oil purified piping system27、污水井Bilge well 12、燃油输送系统Fuel oil transport piping system三、各种管系系统All kinds of pipes舵销Rudder pintle 13、滑油净油系统Lubricating oil purified piping system舵杆衬套rudder stock liner 14、滑油输送系统Lubricating oil transport piping system舵杆轴套Sleeve for rudder stock 15、舱底压载系统Ballast and bilge water piping system 舵销承衬套Bush for rudder pintle 四、仪表类Instructions舵销轴套Sleeve for rudder pintle 1、压力表Pressure gauge上舵承底座Rudder carrier seat 2、真空表Vacuum gauge舵销承座Pintle bearing 3、温度计Thermometer舵杆承座Rudder stock bearing 4、吨位表DWT gauge挡圈Retaining ring 5、遥测表Distant survey gauge舵柄Tiller 6、液全器Level switch7）舵角The angle of rudder5、空压机Air compressor1）主空压机Emergency air compressor2）应急空压机7、传感器Sensor 12、机控室Engine control room五、其它Others 13、台虎钳Vise (=vice)1、风机Fan 14、表铜截止阀Bronze close valve2、防海生物装置Anti-foul STM plant 15、表铜截止止回阀Bronze check valve3、泡沫柜Air foam tank 16、铸铁截止阀Cast iron stop valve4、中间轴Middle shaft 17、铸铁截止止回阀Cast iron check and stop valve5、尾轴Propeller shaft 18、调节阀Adjustable valve6、螺旋桨Propeller 19、溢流阀、安全阀Relief valve7、中间轴承Line shaft bearing 20、减压阀Reducing valve8、泡沫灭火机Foam fire extinguisher 六、材料Material9、饮水消毒装置Sterilizer plant 1、管子Pipe10、主配电板Main switch board 2、无缝钢管Seamless steel pipe (tube)11、机舱集控台Engine room control console 3、紫铜管Purple copper pipe4、铁法兰Iron flange 18、支架（马脚）Clamp5、铜法兰Copper flange 19、油漆Paint6、盲板法兰Blind-flange 20、备件Spare parts7、螺丝（螺栓）Bolt8、双头螺丝Stud 七、生产工具Produce tool9、螺帽（螺母）Nut 1、图纸Drawing10、不锈钢螺丝Stainless steel bolt 2、活络钣Adjustable spanner11、垫片（床）Gasket 3、令司板（梅花钣）Ring spanner12、橡皮床Gum gasket 4、开口钣Open –ender spanner13、纸箔床Paper copper gasket 5、管子钳Pipe wrench14、紫铜床Purple copper gasket 6、凿子Chisel15、石墨床Black lead gasket 7、锒头Hammer16、青铅床Black lead gasket 8、锉刀File17、佛纳Feeler gauge 9、螺丝刀Screwdriver10、油漆滚筒Paint roller 4、首先请检查安装说明和电气绝缘11、油漆刷子Paint brush Please check the condition of installation and insulationfirst12、钢锯Hacksaw 5、我们准备将油水分离器动转13、套筒扳手Socket spanner Now we will run the oily-water separator14、手电筒Torch 6、请检查动转情况15、钻头driller Please check the running condition八、英语会话7、接着我们一个一个地做报警/安全保护装置的功能试验1、早上好good morning Now we will do the function test about alarm and safetydevice2、今天我们准备交验油水分离器8、设备交接基本结束Today we will test the oily-water separator. Now the test is over3、请跟我来9、请部有何修改意见？Please fellow me. Do you have any question ?10、非常感谢17、这里增加一只落水斗Thanks Add a drain plug here11、再见18、请用空气压缩空气吹干Good bye Please dry it by the compressed air12、请把这对法兰撬紧松开19、我将回车间支拿肥皂水Please tighten/release the flange I will com to my works hop to take some soap water13、这路管子是从发电机单元来的20、这个系统非常重要的，一定要认真检查The piping is from to the G/E unit This system is very important ,please check it carefully14、这对法兰/接头在漏21、请交验收整改意见This flange /connection is linking Please check your remarks15、这路系统的试验压力是7 公斤22、天太热了，请休息一会The test pressure of the piping system is 7 bar It’s too hot ,please take a rest16、这里请加强please make a clamp here 23、我负责这项工作I am in charge of this job电气部分ELECTRIC PART一、常用词汇Words and expression 模拟Analog(ue)2182 千赫值班接收机2182KHz watch receiver 锚灯Anchor lightA 异常Abnormal 风速风向仪Anemorumbometer应答Acknowledge 阳极Anode有功功率Active power 天线Antenna执行器Actuator 天线馈线连接器Antenna feeder connector调整Adjust 天线引入绝缘端子Antenna leading –in insulator空气断路器Air circuit breaker 天线共用器Antenna multicoupler 报警系统Alarm system 天线调谐器Antenna tuner交流电Alternating current 电焊机Arc welder电流表ammeter 声音的Audible放大器Amplifier 自动海图标绘仪Auto chart plotter自动舵Auto pilot自动的Automatic自动雷达标绘仪Automatic radar plotting aid球鼻首警告灯Bulbous bow warning light自动电话Automatic telephone 汇流排Bus(-)bar电压自动调节器Automatic voltage regulator 汇流排Bus –tie –in 自动化系统Automation system 蜂鸣器Buzzer压载控制台Ballast control console C、电缆Cable镇流器Ballast 电缆填料函Cable gland底座Base 敷设电缆Cable laying电池Battery 电缆管Cable pipe (conduit)铃Bell 电缆扎带Cable strap弯曲Bend 电缆托架Cable tray床头灯Berth light 校准器Calibrator失电Black out 电容capacitor刹车Brake 阴板Cathode电刷Brush 警告牌Caution plate顶灯Ceiling light 通讯Communication中央处理器Central processing unit 计算机Computer通道Channel 接头Connector充电器Charger 恒电流Constant current充放电板Charging&discharging board 消耗Consumption海图灯Chart table light 触头Contact检查Check 接触器Contactor芯片Chip 控制箱Control box清洁Clean 控制箱Controller雨雪清除器Clear view screen 芯线Core二氧化碳释放报警CO2 release alarm 角灯Corner light同轴电缆Coaxial cable 计算器Counter线圈Coil 电流Current冷库呼叫Cold store calling D、损坏Damage危险气体报警箱Dangerous gas detecting&alarm box双极单刀开关Double pole single way switch白昼信号灯Daylight signal light 双极双刀开关Double pole two way switch 去耦Decoupling set 天线收发转换开关Duplexer台灯Desk light 值班水手呼叫Duty sailor calling控测器Detector 接地Earth拨号Dial 接地排Earth bar数字选择呼叫收信机Digital select –call receiver测深仪Echo sounder调光器dimmer 电工试验板Electric test panel直流电Direct current 电机员Electrical engineer直接起动Direct –on –line starting 电极Electrode磁盘Disk 应急照明分电箱Emergence lighting distribution box显示Display 应急示位标Emergence position indicating radiobeacon遇险信息控制器Distress message controller 应急停Emergence stop 多普勒记程仪Doppler speed log应急配电板Emergency switch board 馈电品Feeder panel机舱报警Engine alarm 滤波器Filter集控台Engine control console 火警复显器Fire alarm repeater机舱监测报警Engine room monitoring&alarm system防火风闸控制单元Fire damper control unit轮机员呼叫Engineer calling panel 火警检测箱Fire detecting box轮机员安全Engineer safety system 火焰探头Flame detector增强群呼叫收讯机Enhance group call receiver 闪光灯Flash light 交换机Exchanger 浮充电Float charge防爆灯Explosion proof light 强光灯Flood light延伸报警板Extension alarm panel 流程图Flow chart故障Failure 流量开关Flow switch故障Fault 荧光灯Fluorescent light反馈Feed back 雾笛Fog horn频率Frequency熔丝Fuse 感温探头Heat detector填料Gasket 底座Holder通用报警General alarm 电笛、喇叭Horn发电机Generator 病房呼叫Hospital calling发电机屏Generator panel 照明Illumination（铜）锣、钟Gong 白炽灯Incandescent light全球卫星定位导航GPS navigator 指示器Indicator组合灯板Group alarm light pillar 卫星 B 站INMARSAT B station 组合起动屏Group starter panel 卫星 C 站INMARSAT C station 电罗经Gyro compass 输入输出Input /output卤素灯Halogen light 安装Install听筒Handset 仪表Instrument硬件Hardware 绝缘胶带Insulating tape航向Heading 绝缘Insulation接口、界面Interface 限位开关Limit switch连锁Interlock 连接Link中断Interrupt 负载Load逆变器Inverter 劳莱收信机Loran receiver接线盒Junction box 磁罗经Magnetic compass键盘Keyboard 主机电子调速器Main engine electronic governor灯泡Lamp 主机功率、纽力仪Main engine power& torque unit液位开关Level switch 主机遥控系统Main engine remote control system液位传感器Level transmitter 主机转速表Main engine revolution meter灯Light 主机安全系统Main engine safety system灯柱Light column 主机增压器转速表Main engine turbo-charger speed meter 照明分电箱Light distribution box 主配电板Main switchboard避雷针Lighting arrester 手动手册Manual标记Mark 移动Move桅杆Mast light 万用表Multimeter母子钟Master& slave clock 铭牌Name plate匹配箱Matching box 窄频直接打印机Narrow-band direct printer测量Measure 航行灯Navigation light兆欧表Megohmmeter 导航系统Navigation system仪表Meter 航行监控台Navigation watch console话筒Microphone 航行警告收信机NAVTEX receiver镜向灯Mirror light 负极Negative监视器Monitor 网络Network莫斯键Morse key 标称值Nominal value电动机Motor 常闭Normally closed塑壳断路器Moulded case circuitbreaker常开Normally open鼠标Mouse 失控灯Not under-command light欧姆表Ohm gauge 正极Positive欧姆收信机Omega receiver 功率、电源Power车钟记录仪Order printer 电力分电箱Power distribution box示波器Oscilloscope 功率因素Power factor过电流Over current 优先卸载Preferential trip过载Overload 压力开关Pressure switch巴拿马动河操舵灯Panama canal steering light 压力传感器Pressure switch 并联、并车Parallel 一次系统Primary system相Phase 打印机Printer光敏电阻Photo resister 程序Program测速传感器Pick up 螺旋桨警告灯Propeller warning light插头Plug 广播Public addressor左舷灯Port light 脉冲Pulse便携电话Portable telephone 按钮Push button雷达Radar 电阻Resistance雷达应答器Radar transponder 逆功率Reverse power收音机Radio 旋转灯Rotating light无线电测向仪Radio direction finder 舵角指示器Rudder angle indicator随机存取存储器Radio system 运转灯Running lamp额定Random access memory 屏幕、屏蔽Screen无功电流Rated power 螺丝刀Screwdriver插座Receptacle 搜索灯Search light录音机、记录仪Recorder 二次系统Secondary system整流器Rectifier 串联Series继电器Relay 屏蔽Shield复位Reset 船名灯Ship name light岸电箱Shore connection box短路Short circuit展示、给-----看Show 电磁阀Solenoid valve分励脱扣Shunt trip 消音Sound off停车Shut down 声力电话Sound power telephone签字Sign 空间加热器Space heater信号集合箱Signal acquisition unit 扳手Spanner信号灯Signal light 喇叭Speaker单边带收发机Single side band transceiver分配器Distributor电笛Siren 右舷灯Starboard light慢车Slow down 起动Start烟气探测报警箱Smoke detecting &alarm box 起动带Start 感烟探头Smoke detector 尾灯Stern light插座Socket 停止Stop软件Software 苏伊士运河尾灯Suez canal stern light电烙铁Soldering iron 支撑物supporter开关Switch 验电笔Test pen打开Switch on 试验程序Test procedure关闭Switch off 热敏电阻Thermistor同步屏Synchronizing panel 热电偶Thermocouple同步表Synchronoscope 温度计Thermometer转速表Tachometer 恒温计Thermostat录音机Tape recorder 触摸屏Touch panel车钟Telegraph 轨迹球Trackball电视Television 收发机Transceiver温度开关Temperature switch 传感器Transmitter温度传感器Temperature transmitter 变压器Transformer接线柱Terminal 脱扣Trip接线排Terminal board 欠电压Under voltage试验Test 不中断电源Uninterrupted power source卸载Unload 二、会话Dialog and conversation超高频VHF telephone 船东o- owner视觉的Visual 验船师s-survey电压Voltage 检验员q-quality inspector电压表Voltmeter 电工e-electrician壁灯Wall light 1、检验电缆敷设瓦特Watt Inspection cable laying波道Waveguide 你能带我去看机舱电缆敷设气象传真收信机Weather fax receiver Q: could you show me cable laying of engine room?驾控台Wheel speed &directionindicator好，走吧。

海工英语

海工英语Rig Manager 平台经理Equipment Supervisor 设备总监Materials Supervisor 材料总监Senior Toolpusher 高级队长Junior Toolpusher 值班队长Driller 司钻Sub Sea Engineer (SSE) 水下工程师Assistant Driller (AD) 副司钻Derrick Man 井架工Floor Man (roughneck) 钻工Barge Master (captain) 船长First Mate (Barge engineer) 大副Control Room Operator (CRO) 压载工Ballast Control Operator (BCO) 压载工Chief Engineer 轮机长Head of Routabout 甲板班长Crane Operator 吊车工Routabout 甲板工Mechanic 机械师Electrician 电气师Repairman 修理工Motorman 轮机员Welder 焊工Radio Operator 电报员Warehouse Man (stock Keeper) 材料员Medic 医生Safety Supervisor 安全监督Interpreter (translator) 翻译Chief Steward 管事Cook 厨师Steward 厨工Laundry Man 洗衣工二. 作业者及服务公司人员( Operator’s Personnel and Service Company Personnel)Drilling Superintendent 钻井监督Company Man (Operator’s Representative) 公司代表Geologist 地质师Mud Logging Engineer (Mud logger) 泥浆录井工程师Sample Catcher 捞砂工Mud Engineer 泥浆工程师ROV Engineer 潜水工程师Cementer 固井工Cement Engineer 固井工程师Testing Engineer 试油工程师Coring Engineer 取芯工程师Wireline Logging Engineer电测工程师。

船舶与海洋工程英语

船舶与海洋工程英语船舶与海洋工程涉及到设计、建造和运营各种类型的船舶以及与海洋资源开发和保护相关的工程。

以下是有关船舶与海洋工程的一些英语词汇和短语：1. Ship Design and Construction:- Naval architecture - 船舶设计- Shipbuilding - 船舶建造- Hull design - 船体设计- Marine engineering - 海洋工程2. Ship Types:- Cargo ship - 货船- Container ship - 集装箱船- Passenger ship - 客船- Oil tanker - 油轮- Fishing vessel - 渔船- Naval ship - 军舰3. Maritime Safety:- Navigation safety - 航行安全- Collision avoidance - 避碰- Search and rescue - 搜救- Emergency response - 应急响应4. Offshore Engineering:- Offshore platform - 海上平台- Subsea engineering - 海底工程- Offshore drilling - 海上钻探- Floating production storage and offloading (FPSO) - 浮式生产储油船5. Oceanography:- Ocean currents - 海洋流- Tidal energy - 潮汐能- Marine ecology - 海洋生态学- Underwater exploration - 水下探测6. Marine Resources:- Fisheries management - 渔业管理- Aquaculture - 水产养殖- Deep-sea mining - 深海矿业- Renewable ocean energy - 可再生海洋能源7. Environmental Protection:- Marine pollution control - 海洋污染控制- Oil spill response - 油污应急响应- Marine conservation - 海洋保护- Sustainable maritime practices - 可持续海洋实践8. International Maritime Organizations:- International Maritime Organization (IMO) - 国际海事组织- International Hydrographic Organization (IHO) - 国际海洋测绘组织- International Maritime Satellite Organization (INMARSAT) - 国际海事卫星组织这些词汇和短语涵盖了船舶与海洋工程领域的一些关键方面，可以作为学习和讨论的起点。

海工船英语词汇

英汉海洋平台技术词汇英汉海洋平台技术词汇AA-60 fire door A-60级防火门a-hundred-year return period百年一遇abrasive (喷砂用的)磨料abrasive paper砂纸AC generator交流发电机AC motor交流电动机accelerated corrosion testing加速腐蚀试验acceptance criteria 合格准则access hole (for welding)=cope hole焊接工艺孔accommodation and power platform (APP) 生活动力平台according to =in accordance with =in line with =as per =in the light of 按照acetylene gas 乙炔acid electrode 酸性焊条acid proof cement 防酸水泥additive 添加剂adhere to 遵守(动词)adherence to 遵守(名词)adjacent columns 相临立柱adverse combination of loads荷载的不利组合adverse condition 不利条件aeronautical radio system 航空无线电系统AFC (approved for construction) 建造批准Aforementioned 上述的aft winch 船艉绞车agitator 搅拌器air blower 鼓风机air compressor 空压机air drive pump 气动泵air hoister 气动绞车air manifold 气包air tight test 气密性试验air-hose 风带aircraft obstruction beacon 航空障碍灯alarm buzzer 报警蜂鸣器alarm horn 报警喇叭aliphatic polyurethane 脂肪族聚氨酯漆allowable (working) stress 许用应力Aluminum alloy anode 铝合金阳极Aluminum ingot 铝锭aluminum paint 银粉漆aluminum sheet 铝皮ambient air temperature 环境气温ambient temperature 环境温度anchor block 地锚块anchor bolt 地脚螺栓anchor ground 锚地anchor pile 锚桩anchor profile/pattern 涂装表面的粗糙度anchor rack 锚架anchoring buoy 锚泊浮筒angle of incidence 入射角angle of reflection 折射角angle probe method 超声波斜射探伤angle steel 角钢angle valve 角阀anode core 阳极芯子anode end face geometry 阳极端面几何形状anode life 阳极寿命anode potential 阳极电位anode stand-off post 支架式阳极的立柱anodic resistance 阳极电阻anti-electrostatic floor 防静电地板anticorrosive paint 防锈漆antipollution measures 防污染措施API specified requirement API规定的要求apparent batter 视斜度applicable API specification API适用规范approach-departure sector 直升飞机起落扇形区appurtenance =attachment =accessory =auxiliary 附件arc air gouging 碳弧气刨arc cutting 电弧切割arc strike 弧击argon arc welding 氩弧焊argon arc welding machine 氩弧焊机articulated tower mooring system 绞接塔系泊系统artificial island 人工岛as per 按照as-built 完工as-built dossier 完工资料as-built drawing 完工图as-rolled 轧制状态assemble 组装(动词)assembly 组装(名词)associated gas 伴生气at the option of A 按A的意愿atmospheric diving system=unpressurized diving system 常压潜水系统atmospheric vent 防空管attachments 附件auto fire alarm system 火灾自动报警系统automatic spraying system 自动喷淋系统B(to be) buttered (焊接的)长肉back chipping 清根back gouging 反面气刨backing weld 打底焊道backpressure regulator(self contained) 背压式调节阀(自力式)backwash return pump 反冲洗回流泵backwash purge tank 反冲洗罐backwash tank 反冲洗水罐Ball hardness 布氏硬度ball valve 球阀bar (截面较小的)圆钢方钢六角钢等bar chart 统计用的柱状图barge bumper 靠船件barge strength and stability 驳船强度及稳性barrel (管件的)加厚段base metal 母材, 基本金属basic design 基本设计basic electrode =lime type covered electrode 碱性焊条battery room 蓄电池间blowout preventer system (BOP system) 防喷器系统beam depth 梁高beam path distance 超声波发射程距bearing strength of the ground 地基承载力bearing stress 支撑应力before welding is initiated 始焊前bending moment 弯矩bending stress 弯曲应力bevel 坡口bevel angle 坡口面角度beveling/chamfering 开坡口bid drawing 招标图纸bilge /fire pump 舱底污水—消防两用泵bilge alarm system 污水报警系统bid/tender for 投标blast cleaning 喷砂除锈blind flange 盲法兰blind spectacle flange 快速盲法兰blow countn 打桩的锤击数blowdown vessel 排放罐blowhole; gas pore 气孔blowout preventer stack 防喷器组buoyant turret mooring 浮筒转塔式系泊boat landing 登船平台bolt, nut and washer 螺栓, 螺母及垫片bolted connection 螺栓连接boom 吊机扒杆boom angle 吊臂倾斜角bore hole 镗孔boss with plug 带有丝堵的管座bottom echo 底面回声bottom sitting drilling platform 坐底式钻井船boundary condition 边界条件bow 船艏box beam 箱形梁box type joint 箱形节点brace 拉筋bracelet anode 手鐲式阳极branch member 支杆breathing apparatus, respirator 防毒面具bridge 栈桥bridge (overhead) crane 天车吊brittleness 脆性brush coating 用毛刷涂漆buckle fastener 绑带bulb angle 球扁钢build-up girder 组合梁bulk head 隔板, 舱壁burn through 烧穿burner 气焊工burr and flashing 飞边毛刺business and management 经营管理butt-welded seam 对接焊缝butterfly valve 蝶阀Ccable layer 敷缆船cable rack tray 电缆托架caisson 沉箱caisson washing pump 洗舱泵caisson-type platform 沉箱式平台can (管件的)段cantilever beam 悬臂梁cantilever jack-up rig 悬臂自升式钻井船cantilever well module 悬臂式井口模块cap beam 帽梁capped steel 半镇静钢capsizing lever 倾覆力臂capsizing moment =overturn moment 倾覆力矩carbon arc air gouging 碳弧气刨carbon dioxide cylinder 二氧化碳气瓶carbon equivalent 碳当量carbon dioxide (CO2) arc welding 二氧化碳气体保护电弧焊cargo master system 货油舱总监控系统cargo tank cleaning machine 洗舱机carrier (搬运) 小车carry out =perform =conduct =execute 进行catenary anchor leg mooring (CALM) 悬链锚腿系泊cathodic protection 阴极保护cellar deck 底甲板cellar shutdown panel (CSDP) 井口系统关断盘cement grout 水泥浆cementing vessel 固井船center line 中心线center of buoyancy 浮心center of floatation 漂心center of gravity 重心center punch 冲子central control room (CCR) 中央控制室central processing platform 中心处理平台centrifugal pump 离心泵centrifuger 离心机ceramic fibres 防火陶棉ceramic tiles 瓷砖certifying authority 第三方检验机构chain block 倒链chair with arm-rests 带扶手的半软椅chamfering 开坡口channel steel 槽钢charpy-V notch energy 夏比V形缺口韧性值charpy-V notch impact test 夏比V形缺口冲击实验chart datum 海图基准面check randomly 抽检check valve 止回阀checkered plate 花纹板chemical composition 化学成分chemical injection package 化学注入撬chemical injection system 化学药剂注入系统chemical seal 化学密封chipping hammer 敲渣锤chisel 风铲chord member 弦杆Christmas tree 采油树circumference 周长circumferential weld 环焊缝classification survey 入级检验clean water injection pump 清水注入泵clean water surge tank 清水缓冲罐clearance 间隙client 业主, 顾客close drain tank 闭式排放罐closed /open circuit 闭/开路closed drain pump 闭式排放泵closed drain tank 闭式排放罐clustered well heads 丛式井口CO2 cylinder unit CO2 气瓶组CO2 extinguisher CO2 灭火器coal tar epoxy paint 含焦油环氧涂料coaming 档水扁钢coating 涂装coating interval 涂漆间隔coefficient 系数cold formed pipe 冷卷管cold shut 冷隔cold work 冷加工collapse ring 加强环板column 立柱combustible gas detector 可燃气体探测器come-along 手搬葫芦commercial blast cleaning 普通级喷砂除锈commissioning 调试compile and maintain a document 编制和保存文件complete penetration groove weld 全熔透坡口焊completion riser 完井立管complex joint 复杂节点compliance with 符合(名词)comply with 符合(动词)composite rockwool ceiling 复合岩棉天花板composite rockwool panel 复合岩棉板concentric reducer 同心大小头conceptual design 概念设计concrete platform 混凝土平台condensate drum 冷凝液罐condensing water 冷凝水conductor 隔水套管conductor guide 套管导向cone 大小口, 锥体conform to =stick to =adhere to 符合, 遵守connection 节点, 连接consumption rate 阳极消耗率continuous beam 连续梁continuous double fillet weld 双面连续贴角焊continuous welding 连续焊contract 合同contraction stress 收缩应力contractor 承包商control valve (accessories handwheel) 带手轮的控制阀control valve assembly 控制阀总成coordinates 坐标系coordination 协调cope hole (焊接)工艺孔corrective and preventive action 纠正和预防措施correlation curve 相关曲线corrosion allowance 腐蚀余量corrosion coupon 腐蚀片corrosion protection 防腐corrugated plate interceptor 斜板分离器couplant UT用的耦合剂coupling 连轴器, 管箍crack 裂纹crane barge, crane vessel 起重船crane support 吊机支撑crater 焊口crawler crane 履带吊车criteria (验收)标准cross angle 交叉角cross section 横截面crow bar 撬杠cruciform bollard 单十字带缆柱crude cooler 原油冷却器crude filter 原油过滤器crude heat exchanger 原油换热器crude loading/export pump 原油外输泵crude loading pump 原油装载泵crude oil drain tank 原油排放舱crude preheat exchanger 原油预热器crude suction strainer 原油吸入滤器crude transfer pump 原油输送泵cup support 垫墩curing time (油漆的)固化时间current capacity (阳极的)电流容量current density (阳极的)电流密度current direction 海流方向curvature radius 曲率半径customer (试比较purchaser需方)客户(签合同后, 客户变需方)cut by torch 以火焰切割cut off 割除, 割除物cutoff allowance 切割裕量cutting plan 排板图cutting sheet 单件图D(in) duplicate 一式两份(to) drive piles 打桩DAC curves 距离—振幅曲线daily diesel filter 日用柴油滤器damage-prone connection 易破坏的节点damper, dampener 减振器DC generator 直流发电机Decibel (dB) 分贝deck beam 甲板梁deck cover 甲板敷料deck crane 甲板吊机deck floor plate 甲板板deck water seal unit 甲板水封装置deep freeze compressor 深冷压缩机deepwater jacket 深水导管架defeat /default /disconnection 缺陷deflection 挠度dehydration degassing vessel 脱水除气器dehydration preheater 脱水预热器dehydrator feed pump 电脱水供给泵delivery of materials 材料交货derrick barge 回转式起重船desander 除砂罐design basis 设计基准design parameters 设计参数detail 详图detail design 详细设计develop /establish a document 编制文件dew point 露点DFT (dry film thickness) 干膜厚度diagonal brace 斜拉筋dial gauge 百分表diaphragm 隔板diaphragm valve 隔膜阀die stamp 钢印diesel daily tank 柴油日用罐diesel filter coalescer 柴油过滤净化装置diesel generator set 柴油发电机组diesel oil daily tank with heater 柴油日用罐(带加热器)diesel pump 柴油泵diesel storage tank 柴油储罐diesel storage tank with heater 柴油储罐(带加热器)diesel tank 柴油罐diesel transfer pump 柴油输送泵differential pressure control valve 差压控制阀diffuser 布风器dihedral angle 二面角dimensional checks 尺寸检验direct /alternating currentarc welding 直/交流电弧焊direct current emergency supply 直流应急电源disassembling 拆除discontinuity 缺陷displacement oil tank 置换油罐distortion from welding 焊接变形distress signals 遇险呼救信号diver 潜水员diver support vessel 潜水作业船document approval and issue 文件的批准和下发documentation 文件编制dog 组装用的刀把dolphin 系缆柱domestic sea water pump 生活海水泵double agent facility 双介质灭火装置double bed 双层床double bevel groove K形坡口double bollard 双柱带缆柱double groove 双面坡口double probe method 双探头法double V groove 双面V形坡口(X形坡口) double plate 垫板, 包板down hill welding 下向焊drain pit 排放池draught gauge 吃水标尺drawing and specification 图纸及技术规格书drawing types 图纸种类图纸种类有:conceptual drawing 概念图纸basic drawing 基本设计图bid drawing 招标图纸design drawing 详细设计图fabrication drawing 加工设计图shop drawing 车间加工图as-built drawing 完工图dredger 挖泥船drift pin 心轴, 销子drift test 管流试验, 管线试通drill 钻头drilling module 钻井模块drilling platform 钻井平台drilling template 钻井基盘drillship, drilling ship 浮式钻井船driving voltage 驱动电压dry chemical extinguisher 干粉灭火器dry-type tree 干式采油树dryer 烘箱during the course of fabrication 在制造过程中during the life of structures 结构寿命期间dye penetrant inspection 着色检验dynamic-positioning rig 动力定位钻井船Eearth lead 地线eccentric reducer 偏心大小头echo height 回波高度edge crimping (卷管的)压头edge preparation 坡口加工effective throat thickness 焊缝计算厚度elbow 弯头electric dehydrator 电脱水器electric desalter 电脱盐器electric drill 手电钻electric heater 电加热器electric submersible pump 电潜泵electric-hydraulic valve 电—液操作阀electrical connection 导电连接electro-slag welding 电渣焊接electrochemical property 电化学特性electrode 电焊条electrode covering 焊条药皮electrode holder 焊把, 焊钳electrolyte 电解质elevation (EL) 标高, 立面图elongation 延伸率emergency air compressor 应急空压机emergency ballast control system 应急压载控制系统emergency BOP recovery system 防喷器紧急回收系统emergency generator 应急发电机emergency light 应急照明灯emergency power station 应急电站emergency shutdown 紧急关断emergency shutdown system (ESD)应急关断系统emergency switch board 应急开关柜emergency switch room 应急配电间emery cloth 金刚砂布emulsion transfer pump 乳化油输送泵engine room 动力舱, 机舱engineering geotechnical vessel 工程地质船engineering vessel 工程船舶entire length 全长equal angle 等边角钢equation 公式equipment base 设备底座erection 安装ERW (electric resistance welding) 电阻焊escape route 逃生路线essential variable 焊接基本参数excess of weight 超重existing structure 已有结构explosion proof equipment 防爆设备exposure distance 防火距离extent of defect in % 缺陷百分率extent of inspection 检验范围extent of repair 返修率external surface of brace 拉筋的外表面extra margin of stress 应力裕量Ffabricated wide flange shape 焊接成的宽翼缘型钢fabrication aids 制造辅助物(又临时吊点)fabrication design 加工设计fabrication phase 制造阶段fabrication sequence 顺序fabrication yard 制造场地face bend test 表面弯曲试验facsimile transceiver 传真收发两用机fastener 紧固件fatigue damage 疲劳破坏field assembly 空间组对, 现场组对field mating point 海上对接点(如导管架与组块对接点) field splice 现场拼接field weld 现场焊缝fifty year return period 五十年一遇file 锉刀filler metal 填充金属final fabrication tolerance 最终制造公差finish coat 面漆finished product 成品finite element analyses 有限元分析fire alarm siren 火灾警笛fire and gas detecting system 火灾—可燃气探测系统fire control panel 消防控制盘fire damper 防火风闸fire door closer, fire proof door 防火门fire extinguishing system 消防系统fire fighting water, fire water 消防水fire foam hydrant 消防泡沫栓fire hose station, hose box 消防箱fire monitor 消防炮fire panel 火灾—可燃气报警显示盘fire proof wall, fire wall 防火墙fire protected plastic tiles 防火塑料地板fire protection wall 防火墙fire station 消防软管箱fire water /foam monitor 消防炮(水或泡沫)fire water deluge system 大水量灭火系统fire water hose rock 消防水软管fire water hydrant 消防水栓fire water jockey pump 消防水增压泵fire water lift pump 消防水提升泵fire water pump 消防水泵fire-fighting vessel, fire boat 消防船fireman box 消防员箱first aid kit 急救箱first coat 底漆first stage hydrocyclone 一级水力旋流器first stage separator 一级分离器fit-up 坡口组对fitter 组装工fixed crude oil washing machine 固定式原油清洗机fixed drilling platform 固定式钻井平台fixed platform 固定式平台fixed tower SPM 塔系泊flame arrester 组火器flame cutting 火焰切割flame cutting droplets and debris 火焰切割形成的熔滴和料头flame cutting machine 火焰切割机flame cutting torch 火焰割枪flammability limits 可燃度极限flange 翼缘, 法兰flare assembly 火炬总成flare boom 火炬臂flow indicator (FI) 流量显示器flare drum 闪蒸罐flare pilot gas 火炬引燃器flare scrubber 火炬分液器flare tower 火炬塔flat bar 扁钢flat plate anode 扁阳极flat welding 平焊flaw 裂纹flaw detectability 缺陷检测灵敏度flaw echo 缺陷回声flexible hose 柔性软管flexible riser 挠性立管floater controlled valve 浮球控制阀floating cargo hose 浮式输油软管floating loading hose 浮式装油软管floating oil production andstorage unit (FPSO) 浮式生产储油装置floating oil storage unit 浮式储油装置floating production platform 浮式生产平台floating production, storageand off-loading tanker 浮式生产储油外输轮floating state 漂浮状态flooding 注水floppy disk 软盘flow chart 流程图frame structure 梁格结构flow quantity recorder (FQ) 累计流量计flow switch 流量开关flux 焊药flux cored arc welding (FCAW) 药芯焊flux-cored electrode 管状焊条flux-cored wire 药芯焊丝foam extinguishing system 固定式泡沫灭火系统foam monitor 泡沫泡foam station 泡沫站fog horn, fog signal 雾笛folding bed 折叠床folding chair 折叠椅foot print 被交位置foot valve 底阀forecastle 艏楼foreman 领班forged steel (FS) 锻钢fork lift 铲车, 叉车forming 压制成型forming of plate into tubular 由板卷成管formula / equation of carbon equivalent 碳当量公式four way valve 四通阀fracture toughness 断裂韧性free water knockout vessel 游离水分离器fresh water pressure vessel 淡水压力罐fresh water pump 淡水泵fresh water tank with electric heater 淡水罐(带加热器)friction coefficient 摩擦系数fuel gas compressor package 燃气压缩机橇fuel gas heater 燃料气加热器fuel gas scrubber 燃气洗涤器fuel gas treatment package 燃料气处理橇fuel oil drain tank 燃料油排放罐fuel pump 燃油泵full coupling 全螺纹的接头full penetration weld 全熔透焊缝funnel-shaped guide 喇叭口状导向furnace 熔炉, 加热炉fusible plug 易熔塞fusion /bond line 熔合线G(to be) ground flush 磨平gantry crane 龙门吊gap gauge 间隙尺gas bottle 气瓶gas cutting 气割gas cutting machine with magnetic wheels 磁轮式气割机gas detector 可燃气体探测器gas export facility 天燃气外输设施gas injection module 注气组块gas metal arc welding (GMAW) 熔化极气体保护焊gas processing plant 天燃气处理厂gas shielded arc welding 气体保护电弧焊gas tungsten metalarc welding (GTAW) 钨极气体保护焊(含氩弧焊)gas turbine generator set 燃气轮发电机组gas turbine power generator 燃气轮机发电机gas welding 气焊gasket 垫圈gate valve 闸阀geophysical survey vessel 物探船girders and webs 水平桁材和垂直桁材girth weld 环缝global positioning system (GPS) 全球定位系统global valve (normally closed) 截止阀(常闭)glycerin 甘油gouging 气刨graphite crucible 石墨坩埚grating 格栅gravity damper 重力风闸gravity platform 平台重力式gravity type foundation 重力式基础grease 黄油, 润滑油grind 打磨grinder 砂轮机grinding 打磨(名词)grinding machine 砂轮机grit 石英砂grit blasting 喷丸除锈groove 熔池groove angle 坡口角guard filter 保护滤器guide funnel 导向喇叭口guide structure 导向结构gusset 节点板, 筋板guyed tower platform 拉索塔平台HH-shape H型钢half nipple 一端带螺纹的接头halogenated hydrocarbon cylinder 卤化烃瓶halogenated hydrocarbon local panel 卤化烃就地控制盘halogenated hydrocarbon fire extinguishing system卤化烃灭火系统hammer 锤子hand operated pump 手动泵hand winch 手动缆绳车handrail 栏杆hard hat 安全帽hardener 固化剂hauling to the front 铅引至码头前沿hazardous area 危险区heat affected zones (HAZ) 热影响区heat detector 热探测器heat exchanger 热交换器heat medium drain tank 热介质排放罐heat number 炉号heat traced pipeline 伴热管线heat treater 加热器处理器helmet 安全帽, 焊接面罩heat treatment 热处理heater 加热器heater treater 热处理器heater treater feed pump 热处理器供液泵heating medium boiler package 热介质锅炉橇heating medium circulating package 热介质循环橇heating medium collection tank 热介质收集罐heating medium diesel daily tank 热介质柴油日用罐heating medium drain pump 热介质排放泵heating medium drain tank 热介质排放罐heating medium expansion vessel 热介质膨胀罐heating medium make-up pump 热介质再启动泵heating medium oil, thermal oil 传热介质油heating medium storage tank 热介质油储存罐heating, ventilation and airconditioning system (HAV) 采暖, 通风, 空调系统heave wall section 厚壁段heavy can 节点加厚段heavy duty coating 厚层防腐heavy plate 厚板heavy wall pipe 厚壁管helideck 直升机甲板hex head bolt 六角头螺栓high/low pressure switch (PSHL) 高-低压开关high concentration gas alarm 高浓度可燃气报警high pressure condensate tank 高压凝析油罐high pressure flare 高压火炬high pressure separator (HP separator) 高压分离器high strength steel 高强度钢high-low 错皮histogram (统计用)直方图hold 待定hold point (检验的)停点holder 焊钳holiday detector 气孔探测仪horizontal distance 水平距离horizontal welding 横焊hose 软管hose assembly 软管总成hose connection 软管接头hose handling crane 软管起升吊机hose reel 软管轮hot dip galvanizing 热浸锌hot water pressure vesselwith electric heater热水压力罐(带加热器)hot work 明火作业human life and property 人民生命财产hydrant 消火栓hydraulic pile-driving hammer 液压打桩锤hydraulic press 液压机hydrostatic/hydraulic test 水压试验hyperbaric diving system =pressurizeddiving system高压潜水系统Iice-breaker 破冰船if (when) necessary 若有必要ignitor 点火器immersion suit 防寒救生衣impact resistance 耐冲击波impressed-current protection system 外加电流保护系统in accordance with 按照in any jacket plane 在任意导管架平面内in line with 按照in the light of 按照in-process inspection 工序间的检验inclined stair 斜梯include but not limited to 包括但不限于include / groove angle 坡口角度inclusion 夹杂物incomplete fusion 未熔合incomplete penetration 未焊透inflatable liferaft 气胀式救生筏inlet gas generator package 惰性气体发生器橇inorganic Zine primer 无机锌底漆inside diameter 内径inspection 检验inspection criteria 检验标准installation site 安装现场instrument air receiver 仪表空气接受器instrument capillary tube 仪表控制管线instrument master control room 仪表总控制室insulating flange 绝缘法兰insulation 保温insulation (heat traced) 保温加热器intact / damage stability 完整/破损稳性interference (杆件之间的)相碰, 打架intergranular corrosion 晶间腐蚀intermediate strength steel 中强度钢intermittent welding 断续焊internal and external beveling 内外坡口internal diameter 内径internal quality audits 内部质量审核internal stress 内应力interpass temperature 层间温度intersected pipe 被交管intersection line 相关线invitation for bid =call for bid 招标JJ-tube J形管jack 千斤顶jack-up rig 自升式钻井船jacket 导管架jacket cap 导管架帽jacket handling 导管架扶正jacket launching and upending 导管架下水及竖立jacket launching barge 导管架下水驳船jacket leg 导管架腿柱jacket leveling 导管架调平jacket lifted on and off the barge吊上及吊下驳船的导管架jacket lifting eye 导管架吊耳jacket modification 导管架改造jacket panel 导管架片jacket panel assembly 导管架片组对jacket positioning 导管架定位jacket securing 导管架固定jacking state 升降状态jacking system 升降系统jockey pump 供消防水干管的补给水泵joint can 节点加厚段joint detail 节点详图junction box (explosion proof) 接线箱(防暴型) Kkilled steel 镇静钢kingpost 将军柱key plan 总图, 索引图Llack of fusion 未熔合lack of penetration 未焊透ladder 直梯ladle analysis 熔炼分析lamellar tearing 层状撕裂lap 焊缝盖面lap welding 搭接焊lateral load 側向荷载launch / cargo barge 滑道式/装载式驳船launch way and rocker 滑道和摇臂launching and uprighting of a jacket导管架的下水和直立launching truss 下水珩架lay barge 铺管船lead section and subsequentadd-ons of piles 首桩及后续状段leak test 密封性试验(试漏)leg 桩腿, 导管leg of a fillet weld (角焊缝)焊角高度level 水平仪level gauge (with drain) 液位仪(带排放) life boat 救生艇life boat davit, davit 吊艇架life buoy 救生圈life jacket 救生衣life raft, life float 救生筏lift calculation 吊装计算lifting gear 吊艇机lifting load 起吊荷载lifting lug 吊点lifting padeye 吊点lifting up of panel structure 单片起吊light type combustible gas 轻质可燃气体detector 探测器line pipe 管线管line throwing apparatus 抛绳装置liquid trap 液体捕集器living quarter 生活块LNG carrier, LNG tanker 液体天然器运输船loading arm 输油臂loading flexible hose 柔性装载软管loadout and seafastening 装船固定local deformation 局部变形local stress 局部应力longitudinal seam/weld 纵焊缝low explosion limit (LEL) 爆炸下限low heat input 低热量输入low hydrogen type electrode 低氢型焊条low pressure scrubber 低压气净化器low stress round nosed die stamp 低应力圆头钢印lower deck 下甲板lub oil drain tank 润滑油排放罐lub oil tank with heater 润滑油罐(带加热器)lubricant oil transfer pump 边润滑油传输泵lug 吊耳Mmachinery deck 机械甲板machining 机加工macrosection 宏观断面magnetic particle and suspension 磁粉和悬浮magnetic particle technique (MT) 磁粉探伤main boiler 主锅炉main deck 主甲板main generator set 主发电机组main process line 主要工艺管线main switch room 主变电间main transformer room 主变压器室make-up drawing 造管图manhole 人孔manifold 管汇manned platform 驻入平台manual /hand welding 手工焊manufacturer's instruction 产品使用说明marine growth 海生物marine radio system 海事通讯系统marine transportation 海运marking 做标记, 划线marking and cutting 划线下料mat support jack-up rig 沉垫自升式钻井船material 材质, 材料material identification 材料标识material list 材料表material storage 材料储存material substitution 材料代用material take-off 材料估算单material traceability 材料跟踪maximum operating water depth 最大工作水深mean sea level (MSL) 平均海平面mechanical property 机械性能mechanical test 机械性能试验medium pressure separator (MP separator) 中压分离器member 杆件member drawing (杆件的)单件图member number 杆件号metacenter 稳心metal lash 钢板网mezzanine deck 夹层甲板middle deck 中甲板mild steel 低碳钢mill 钢厂mill certificate 厂家的材质证书mill scale 钢材出厂时的表面氧化皮mill sheet 制造工艺规程表mineral slag 矿渣miscellaneous items 附件mismatch =high-low 错皮mobile drilling platform /rig 移动式钻井平台mobile radio system 移动式无线电系统model test 模型试验module 组块mold 模具mold lofting 放样moment 力矩moment of longitudinal inclination 纵倾力矩moment of transverse inclination 横倾力矩moment of inertia 惯性矩mooring bit 系缆柱mooring cable 系泊缆绳mooring dolphin 系缆柱mooring head 系泊头mooring template 系泊基盘mooring yoke 系泊钢臂motor operated valve 电动阀move to yard front 移至码头前沿mud mat 防沉板mudline 泥线multi-point mooring spread mooring 多浮筒系泊系统multi-purpose epoxy 多用途环氧漆multi-supported beam 连续梁multi-well template system 多井基盘系统multihead metering pump 多头计量泵multipass welding 多层焊multiple lift 多台吊车联合起吊Nnavigational light 导航灯NC (numerical-control) cutting machine 数控切割机near white metal 接近金属白色needle valve 针阀nipple 对丝node can 节点段nominal diameter 公称直径non-combustible 不可燃物质non-conformance 不一致事项nondestructive examination (NDE) 无损检验nondestructive testing (NDT) 无损检验N DT include :radiographic technique (RT) 射线探伤ultrasonic technique (UT) 超声波探伤penetrant technique (PT) 浸透检验magnetic particle technique (MT) 磁粉探伤visual inspection 外观检验nonskid ceramic mosaic 防滑陶瓷马赛克normal practice 通常作法normalize 正火normally open /close valve 常开/常闭阀notch toughness 缺口韧性NRL (Naval Research Laboratory)drop weight test NRL 落锤试验nut 螺母Oobsolete document 作废文件oceanographic research vessel 海洋调查船offshore drilling installation 海上钻井设施offshore drilling rig 海上钻井装置offshore hook-up 海上连接offshore installation 海上安装offshore installation site 海上安装现场offshore oil exploration 海洋石油勘探offshore platform 海洋平台offshore structure 海洋结构物oil boom, oil fence 围油栅oil concentration (污水)含油浓度oil depot 油库oil fence reel 围油栅卷筒oil moisture content 油雾含量oil pollution 石油污染oil recovery vessel 污油回收船oil spill 溢油oil storage barge 储油轮oil storage, loading and transportation equipment 储油, 装油与输油设备oil treatment facility 油处理设施oily water tank 含油污水仓oily water transfer pump 污油水传送泵one-line diagram 单线图onshore fabrication 陆上预制open drain pump 开式排放泵open drain tank 开式排放罐open drain tank with heater 开式排放罐(带加热器) open firing point 明火点operating condition 作业条件operating state 作业状态operation draft 作业吃水orifice plate 孔板流量计original 原稿out of roundness 椭圆度outside diameter (OD) 外径ovality 椭圆度over coating intervals 复涂间隔over head crane 天车吊overboard 舷外overhanging beam 悬臂梁overhead welding 仰脸焊overlap 焊瘤overlapping joint 搭接节点owner 业主oxyacetylene gas welding 氧-乙炔气焊oxyacetylene welding 氧乙炔焊oxygen cylinder 氧气瓶oxygen hose 氧气带Ppackaged air conditioner 空调机橇块packer 封隔器padeye 吊点paint brush 油刷子paint roller 油漆滚子painter 油漆工panel assembling 平面组对, 单片组对parasitic echo 干扰回声parent steel 母材past successful practice 以往成功的作法pedestal crane 基座式吊机pedestal crane 平台用吊机peening 捶击penetrant technique (PT) 浸透检验perimeter 周长periodical survey 定期检验permissible stress 许用应力perpendicularity of pipe end 管端垂直度personnel protection 人身保护phenolic paint 酚醛树脂涂料Philips driver 十字螺丝刀phthalic paint 苯二甲酸涂料pig launcher 清管器发射器pig receiver 清管接收器pile cap 桩帽pile driving records 打桩记录pile driving refusal 拒捶点pile extracting 拔桩pile foundation 桩基pile guide 桩导向pile penetration 桩的贯入度pile section /segment 桩段pile sleeve 桩套筒pile spacer 扶桩间隙块pile washing out 冲桩piling 打桩piling barge 打桩船pilot house 驾驶室pinhole 针尖状气孔pipe diameter 管径pipe fitting 管件pipe rack 管子托架pipe shop 管子支撑pipe wrench 管钳pipeline 管线, 管道pipeline laying barge 铺管船piping and instrumentdiagram (P&ID) 管线仪表图plain end 无螺纹管端plan 平面图, 布置图plasma arc cutting (PAC) 等离子弧切割plasma arc welding (PAW) 等离子弧焊接plate girder 板梁plate type heat exchanger 板式换热器platform 平台platform positioning on the site 导管架的现场定位platform-to-shore radio system 平台-海岸无线电系统pliers 钳子plug 丝堵plug valve 旋塞阀plummet 铅坠plus or minus 2 正负2pneumatic binary signal 双向气动信号pneumatic lines 气控管线pneumatic operated valve 气动操作阀pneumatic operated withmanual reset valve 手动复位气动阀pneumatic test 气压试验polarization potential (阳极的)极化电位polarized steel 极化铁polyurethane paint 聚氨酯涂料porosity 密集气孔port hole 舷窗portable extinguisher 手提式灭火器portable two-way radio 双向无线电话positioner 定位器positioning 定位positive displacement flow meter 容积式流量计positive flow meter 正位流量计postweld head treatment 焊后热处理pot life (油漆的)混合期效power wire brush 电动钢丝刷preheat temperature 预热温度preheater 预热器pressure differential flow meter 差压流量计pressure gauge 压力表pressure regulation valve 压力调节阀pressure regulator(external tap) 压力调节阀(阀外引压)pressure relief valve 压力释放阀pressure safety valve 压力安全阀pressure vessels 压力容器primary structural member 主结构杆probe 探头procedure qualification record (PQR) 焊接工艺评定process 工序port 左舷。

船舶海洋工程词汇

Vocabulary summary(二)⏹1.货舱： Cargo hold⏹甲板间舱（二层舱）tween deck space⏹二层甲板tween deck⏹上层甲板间舱upper tween deck space⏹中层甲板间舱mid tween deck space⏹下层甲板间舱lower tween deck space⏹下层舱lower hold⏹肋骨frame⏹货舱出入口access⏹2. 舱口和舱口盖： Hatchways and covers ⏹舱口hatchway, hatch⏹舱口活动横梁portable beam⏹舱口围板hatch(hatchway) coaming⏹舱口围板扶强材stiffener⏹舱口盖hatch cover⏹机械舱口盖mechanical hatchcover⏹绞链舱口盖swinging hatch cover⏹⏹液压折叠式舱口盖hydraulic-folding hatchcover⏹多板滚动式舱口盖multipanel hatchcover⏹滚动式舱口盖rolling hatchcover⏹滑动式舱口盖sliding hatchcover⏹舱盖板hatch cover plate(panel)⏹托架carrier⏹导轨guide rail⏹轨道轮子track wheel⏹3.甲板: Deck⏹甲板板deck plating⏹甲板开口deck opening⏹甲板边板deck stringer⏹甲板骨架deck framing⏹甲板纵桁deck girder⏹甲板纵骨deck longitudinal⏹甲板强横梁deck transverse⏹甲板横梁deck beam⏹主甲板main deck⏹上甲板upper deck⏹前甲板fore deck⏹后甲板after deck⏹第二甲板second deck⏹下层甲板lower deck⏹居住甲板accommodation dec k⏹上层建筑甲板superstructure deck⏹艏楼甲板forecastle deck⏹艉楼甲板poop deck⏹桥楼甲板bridge deck⏹驾驶甲板navigation deck⏹舱壁甲板bulkhead deck⏹甲板室甲板deckhouse deck⏹平台甲板platform deck⏹罗经甲板compass deck⏹干舷甲板freeboard deck⏹分舱甲板subdivision deck⏹强力甲板strength deck⏹开敞甲板open deck⏹露天甲板exposed (weather) deck⏹遮蔽甲板shelter deck⏹游步甲板promenade deck⏹旅客甲板passenger deck⏹升高甲板raised deck⏹前升高甲板raised fore deck⏹后升高甲板raised quarter deck⏹车辆甲板vehicle deck⏹甲板覆层Deck covering⏹化学敷料composition⏹绝缘层insulation⏹4. 支柱： Pillar⏹组合支柱built up pillar⏹立柱upright⏹5. 舱壁: Bulkhead⏹（非）水密舱壁(non-) watertight bulkhead ⏹横向舱壁transverse bulkhead⏹纵向舱壁longitudinal bulkhead⏹纵中舱壁central longitudinal bulkhead⏹防撞舱壁collision bulkhead⏹制荡舱壁wash bulkhead⏹平面舱壁plane bulkhead⏹槽形舱壁corrugated bulkhead⏹风雨密舱壁weathertight bulkhead⏹舱壁扶强材bulkhead stiffener⏹舱壁贯穿孔penetration⏹6. 肘板： Bracket⏹梁肘板beam knee⏹货舱内肋骨下端肘板lower bracket⏹舭肘板bilge bracket⏹上肘板upper bracket⏹防倾肘板tripping bracket⏹7. 通风筒： Ventilator⏹通风筒围板ventilator coaming⏹通风筒盖ventilator cover⏹通风筒帽ventilator cap⏹通风筒开口ventilator opening⏹防火挡板damper⏹防火网flame screen⏹风雨密关闭装置weathertight closing appliance ⏹8. 空气管： Air pipe⏹空气管头air pipe head⏹空气管管口air pipe opening⏹空气管接头air pipe connection⏹9. 开口： Opening⏹甲板开口Deck opening⏹货舱开口Hatch opening⏹机舱开口Machinery space opening⏹人孔Manhole⏹人孔盖Manhole cover⏹减轻孔Lightening hole⏹泄水孔Scupper⏹排水孔Discharge⏹进水孔Inlet⏹流水孔Drain hole⏹透气孔Air hole⏹吸口Suction。

1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。

海工船英语词汇

合集下载

海洋工程专业词汇

船舶英语必备实用词汇

船舶与海洋工程专业单词总结

海洋海工英语词汇总结

船舶与海洋工程专业常用词汇英汉对照汇总

船舶工程专业英语

海工英语

船舶与海洋工程英语

海工船英语词汇

船舶海洋工程词汇

文档推荐

最新文档

海工船英语词汇

合集下载

海洋工程专业词汇

船舶英语必备实用词汇

船舶与海洋工程专业单词总结

海洋海工英语词汇总结

船舶与海洋工程专业常用词汇英汉对照汇总

船舶工程专业英语

海工英语

船舶与海洋工程 英语

海工船英语词汇

船舶海洋工程词汇

文档推荐

最新文档

船舶与海洋工程英语