LTC2246CUH#PBF;LTC2247CUH#PBF;LTC2247IUH#PBF;LTC2248IUH#PBF;LTC2246IUH#PBF;中文规格书,Datasheet资料

LTC4054-4.2/LTC4054X-4.2OPERATIOUThe LTC4054 is a single cell lithium-ion battery charger using a constant-current/constant-voltage algorithm. It can deliver up to 800mA of charge current (using a good thermal PCB layout) with a final float voltage accuracy of ±1%. The LTC4054 includes an internal P-channel power MOSFET and thermal regulation circuitry. No blocking diode or external current sense resistor is required; thus,the basic charger circuit requires only two external com-ponents. Furthermore, the LTC4054 is capable of operat-ing from a USB power source.Normal Charge CycleA charge cycle begins when the voltage at the V CC pin rises above the UVLO threshold level and a 1% program resistor is connected from the PROG pin to ground or when a battery is connected to the charger output. If the BAT pin is less than 2.9V, the charger enters trickle charge mode.In this mode, the LTC4054 supplies approximately 1/10the programmed charge current to bring the battery volt-age up to a safe level for full current charging. (Note: The LTC4054X does not include this trickle charge feature).When the BAT pin voltage rises above 2.9V, the charger enters constant-current mode, where the programmed charge current is supplied to the battery. When the BAT pin approaches the final float voltage (4.2V), the LTC4054enters constant-voltage mode and the charge current begins to decrease. When the charge current drops to 1/10 of the programmed value, the charge cycle ends.Programming Charge CurrentThe charge current is programmed using a single resistor from the PROG pin to ground. The battery charge current is 1000 times the current out of the PROG pin. The program resistor and the charge current are calculated using the following equations:R V I I VR PROG CHG CHG PROG==10001000,The charge current out of the BAT pin can be determinedat any time by monitoring the PROG pin voltage using the following equation:I V R BAT PROGPROG=•1000Charge TerminationA charge cycle is terminated when the charge current falls to 1/10th the programmed value after the final float voltage is reached. This condition is detected by using an internal,filtered comparator to monitor the PROG pin. When the PROG pin voltage falls below 100mV 1 for longer than t TERM (typically 1ms), charging is terminated. The charge current is latched off and the LTC4054 enters standby mode, where the input supply current drops to 200µA.(Note: C/10 termination is disabled in trickle charging and thermal limiting modes).When charging, transient loads on the BAT pin can cause the PROG pin to fall below 100mV for short periods of time before the DC charge current has dropped to 1/10th the programmed value. The 1ms filter time (t TERM ) on the termination comparator ensures that transient loads of this nature do not result in premature charge cycle termi-nation. Once the average charge current drops below 1/10th the programmed value, the LTC4054 terminates the charge cycle and ceases to provide any current through the BAT pin. In this state, all loads on the BAT pin must be supplied by the battery.The LTC4054 constantly monitors the BAT pin voltage in standby mode. If this voltage drops below the 4.05V recharge threshold (V RECHRG ), another charge cycle be-gins and current is once again supplied to the battery. To manually restart a charge cycle when in standby mode, the input voltage must be removed and reapplied, or the charger must be shut down and restarted using the PROG pin. Figure 1 shows the state diagram of a typical charge cycle.Charge Status Indicator (CHRG)The charge status output has three different states: strong pull-down (~10mA), weak pull-down (~20µA) and high impedance. The strong pull-down state indicates that the LTC4054 is in a charge cycle. Once the charge cycle has terminated, the pin state is determined by undervoltageNote 1: Any external sources that hold the PROG pin above 100mV will prevent the LTC4054from terminating a charge cycle.LTC4054-4.2/LTC4054X-4.2。

Manuals+— User Manuals Simplified.CELESTRON 22462 StarSense Explorer SCT DX 5 User Guide Home » Celestron » CELESTRON 22462 StarSense Explorer SCT DX 5 User GuideContents1 CELESTRON 22462 StarSense Explorer SCT DX52 Installation Instructions3 Moving the Telescope4 Aligning the Finderscope5 Attaching the Smartphone6 Documents / Resources6.1 References7 Related PostsCELESTRON 22462 StarSense Explorer SCT DX 5Installation Instructions1. Unpack your telescope and verify that all parts are present. Your StarSense Explorer DX includes: a telescopetube, a tripod and mount head, an accessory bag, slow motion controls, an accessory tray, two eyepieces, an erect image diagonal, a finder scope, a Star Sense phone dock, StarSense Explorer Powered by SkySafariTM app code card, and a hex key (hidden inside the slot in the front of the mount head).2. To set up the tripod, spread the legs outward until they are fully extended and push down the center leg brace.3. Extend the legs of the tripod by loosening the three hand knobs on each leg. Pull each leg section all the wayout and tighten the hand knobs to secure them in place.4. Place the accessory tray on top of the center brace and line up the three holes. Insert the three thumb screwsthrough the bottom of the leg brace and thread them into the tray.5. To attach the slow-motion knobs to your mount, first locate the supplied hex key hidden inside the slot in thefront of your mount.6. Place the slow-motion control knob over the D-shaped gear shaft and push inward to make sure it is fullyseated. Use the hex key to tighten the setscrews onto the gear shaft. Return the hex key to its storage position in the front of the mount.7. Hold the telescope tube next to the mount with the dovetail bar on the tube facing the clamp on the top of themount arm.8. Slide the dovetail bar into the clamp at the top of the mount and tighten the hand knob on the bottom of theclamp to secure the telescope in place.9. Locate the erect image diagonal and remove the plastic covers. Insert the barrel of the diagonal into the backof the telescope tube and secure in place by tightening the set screws.10. Insert the barrel of the 25 mm eyepiece into the diagonal and tighten the set screw.11. Loosen the two Phillips head screws on the side of the finder scope and slide the finderscope onto themounting dovetail on the top of the telescope tube. The large window on the finder should be facing the front of the telescope. Secure the bracket by tightening the Phillips head screws on the side of the finderscope.12. There is a small clear plastic tab inserted between the battery and the contact. This was included to preventthe battery from discharging during shipment. Pull this out to allow your battery to work.13. To install the StarSense phone dock, insert the bayonet mount on the side of the dock into the port on the sideof the mount opposite the dovetail clamp.14. Line up the arrow on the dock with the alignment mark on the mount and press inward while turning the dockcounterclockwise until the orange release button snaps into place in the hole on the dock.15. To remove the dock, press the orange release button and turn the dock clockwise until the bayonet mountreleases.16. Remove the lens cap from the front of the telescope. To observe, look through the eyepiece as shown above.Focus the image by turning the knob below the eyepiece and diagonal.Downloading and Activating the AppBefore you take your telescope outside, download the StarSense Explorer powered by SkySafariTM app to your mobile device. Search for “Celestron StarSense Explorer” in the Apple App Store or Google Play. The app is large, so we recommend downloading it while connected to Wi-Fi.1. Once you have downloaded the app, locate the orange postcard in your telescope box. Launch the app. Whenprompted, enter the activation code on the postcard to activate the app. Your code will unlock up to 5 devices. Moving the Telescope1. The StarSense Explorer DX mount has slip clutches in both axes. To make large movements with thetelescope, simply hold a tripod leg with one hand and use the other hand on the telescope tube to push the telescope in the desired direction.2. To make fi ne adjustments or to track celestial objects, turn both slow motion knobs as required.Aligning the FinderscopeThe finder is one of the most important parts of your telescope. It helps you locate objects and center them in the eyepiece. The fi rst time you assemble your telescope, you need to align the finder to the telescope’s main optics. It’s best to do this during the day*.1. CHOOSE A TARGETTake the telescope outside during the day and fi nd an easily recognizable object, such as a streetlight, car license plate or sign. The object should be as far away as possible, but at least a quarter mile away.2. CENTER THE TARGET IN THE EYEPIECE Look through the telescope using your lower powered eyepiece.Move the telescope until the object you chose lies in the center of the view. If the image is blurry, gently turn the focus knob until it comes into sharp focus.NOTE: The image in your telescope may appear inverted. This is perfectly normal in an astronomicaltelescope.*SOLAR WARNING! Never attempt to view the Sun through any telescope without a proper solar filter!3. LOOK THROUGH FINDERSCOPEOnce the object is centered in your 25 mm eyepiece, look through the finderscope and locate the red dot. 4. ADJUST THE FINDERSCOPEWithout moving the telescope, use the two adjustment knobs to move the finder around until the red dot appears over the same object you are observing in the telescope’s 25 mm eyepiece.5. YOUR FINDERSCOPE IS NOW ALIGNED!It should not require realignment unless it is bumped or dropped.Attaching the Smartphone1. Remove the large cap covering the mirror on the front of the StarSense dock.2. Pull open the spring loaded slider on the top of the phone dock and set the phone into the holder so it is flushwith the bottom lip of the phone holder. Slowly release the slider to secure the phone in place. Most phones fit into the dock with the case on. However, you may need to remove your phone case if it is especially bulky or unable to fit into the clamp (i.e. folio style cases).Congratulations! Your telescope is now set up and you are ready to explore the cosmos. Take the telescope outside, insert your 25 mm eyepiece, remove the lens cap, insert your smartphone into the holder, and launch the /pages/warrantyDocuments / ResourcesCELESTRON 22462 StarSense Explorer SCT DX 5 [pdf] User Guide22462 StarSense Explorer SCT DX 5, 22462, StarSense Explorer SCT DX 5, Explorer SCT DX5, SCT DX 5, DX 5ReferencesCelestron - Telescopes, Telescope Accessories, Outdoor and Scientific ProductsTechnical Support | CelestronWarranty | CelestronManuals+,。

Interleaved Die (Multi-LUN) OperationsIn devices that have more than one die (LUN) per target, it is possible to improve per-formance by interleaving operations between the die (LUNs). An interleaved die (multi-LUN) operation is one that individual die (LUNs) involved may be in any combination of busy or ready status during operations.Interleaved die (multi-LUN) operations are prohibited following RESET (FFh, FCh),identification (90h, ECh, EDh), and configuration (EEh, EFh) operations until ARDY =1for all of the die (LUNs) on the target.During an interleaved die (multi-LUN) operation, there are two methods to determine operation completion. The R/B# signal indicates when all of the die (LUNs) have finish-ed their operations. R/B# remains LOW while any die (LUN) is busy. When R/B# goes HIGH, all of the die (LUNs) are idle and the operations are complete. Alternatively, the READ STATUS ENHANCED (78h) command can report the status of each die (LUN) in-dividually.If a die (LUN) is performing a cache operation, like PROGRAM PAGE CACHE (80h-15h),then the die (LUN) is able to accept the data for another cache operation when status register bit 6 is 1. All operations, including cache operations, are complete on a die when status register bit 5 is 1.Use the READ STATUS ENHANCED (78h) command to monitor status for the addressed die (LUN). When multi-plane commands are used with interleaved die (multi-LUN) op-erations, the multi-plane commands must also meet the requirements, see Multi-Plane Operations for details. After the READ STATUS ENHANCED (78h) command has been issued, the READ STATUS (70h) command may be issued for the previously addressed die (LUN).See Command Definitions for the list of commands that can be issued while other die (LUNs) are busy.During an interleaved die (multi-LUN) operation that involves a PROGRAM-series (80h-10h, 80h-15h, 80h-11h) operation and a READ operation, the PROGRAM-series operation must be issued before the READ-series operation. The data from the READ-series operation must be output to the host before the next PROGRAM-series operation is issued. This is because the 80h command clears the cache register contents of all cache registers on all planes.When issuing combinations of commands to multiple die (LUNs) (e.g. Reads to one die (LUN) and Programs to another die (LUN)) or Reads to one die (LUN) and Reads to an-other die (LUN)), the host shall issue the READ STATUS ENHANCED (78h) command before reading data from any LUN. This ensures that only the LUN selected by theREAD STATUS ENHANCED (78h) command responds to a data output cycle after being put into data output mode, and thus avoiding bus contention. After the READ STATUS ENHANCED (78h) command is issued to the selected die (LUN) a CHANGE READ COL-UMN (05h-E0h) or CHANGE READ COLUMN ENHANCED (06h-E0h) command shall be issued prior to any data output from the selected die (LUN).32Gb, 64Gb, 128Gb, 256Gb Asynchronous/Synchronous NAND Interleaved Die (Multi-LUN) OperationsIf the SYNCHRONOUS RESET (FCh) command is issued while in the OTP operation mode, the target will exit OTP operation mode and the synchronous interface remains active.Table 15: OTP Area DetailsPROGRAM OTP PAGE (80h-10h)The PROGRAM OTP PAGE (80h-10h) command is used to write data to the pages within the OTP area. To program data in the OTP area, the target must be in OTP operation mode.To use the PROGRAM OTP PAGE (80h-10h) command, issue the 80h command. Issue five address cycles including the column address, the page address within the OTP page range, and a block address of 0. Next, write the data to the cache register using data in-put cycles. After data input is complete, issue the 10h command.R/B# goes LOW for the duration of the array programming time, t PROG. The READ STA-TUS (70h) command is the only valid command for reading status in OTP operation mode. The RDY bit of the status register will reflect the state of R/B#. Use of the READ STATUS ENHANCED (78h) command is prohibited.When the target is ready, read the FAIL bit of the status register to determine whether the operation passed or failed (see Status Operations).The PROGRAM OTP PAGE (80h-10h) command also accepts the CHANGE WRITE COL-UMN (85h) command during data input.If a PROGRAM PAGE command is issued to the OTP area after the area has been protec-ted, then R/B# goes LOW for t OBSY. After t OBSY, the status register is set to 60h.Figure 72: PROGRAM OTP PAGE (80h-10h) OperationDQ[7:0]R/B#32Gb, 64Gb, 128Gb, 256Gb Asynchronous/Synchronous NAND One-Time Programmable (OTP) OperationsTable 20: Output Drive Strength Impedance Values (V CCQ = 2.7–3.6V) (Contin-ued)Table 21: Pull-Up and Pull-Down Output Impedance MismatchNotes: 1.Mismatch is the absolute value between pull-up and pull-down impedances. Both aremeasured at the same temperature and voltage.2.Test conditions: V CCQ = V CCQ (MIN), V OUT = V CCQ × 0.5, T A = T OPER .32Gb, 64Gb, 128Gb, 256Gb Asynchronous/Synchronous NAND Output Drive Impedance。

Tektronix 2246 2245With complimentsHelm ut Singer Elektronik www.helmut-singer.de ********************* fon +49 241 155 315 fax +49 241 152 066 Feldchen 16-24 D-52070 Aachen Germany2246/2245• Bright, Crisp Display With HighWriting Rate• Four Independent Channels• 100-MHz Bandwidth With 2-ns/DivTime Base• On-Screen Scale-Factor Readouts • Flexible TriggeringAuto Level and Auto HF, L F, NoiseReject, TV Line and TV Field• Delayed Sweep• Control Status Lights• 2% Vertical and Horizontal Accuracy • 2 mV/Div Vertical Sensitivity at Full Bandwidth• Specially Designed Probe Improved,Rugged Tip Hybrid Circuitry forImproved Performance• New Labeled Volts Cursors WithGround-Referenced Readings andOn-Screen Readouts (2246)• Meets or Exceeds MIL-28800 forHarsh Environments (2246 Opt 1Y)• Hands-Off Voltmeter Measurements+Peak and -PeakPeak-to-PeakGated PeaksGated Peak-to-PeakDC (2246)• New SmartCursors™Track Voltmeter MeasurmentsVisually Indicate Trigger Level andGround (2246)• Time Measurements With Cursors orAlternate Delayed Sweep ATime• Three-Year Warranty—Five-YearOption• UL Listed, CSA CertifiedTYPICAL APPLICATIONSLogic Design and RepaiiCommunicationsPower Supply DesignHigher Performance, Lower PriceThe pcrformance/price ratio for portabkoscilloscopes has been substantiallyupgraded. No other portable scope c a noffer the range of productivity enhancing features and performance charaeleristics at a comparable low price th anthe Tfektronix 2245 and 2246.Features That Promote ProductivityFour independent channels speedtroubleshooting and design tasks b yallowing simultaneous observation o lmultiple test points. Front-panel set-upsare simplified by pushbutton-activatedfunctions and on-screen scale factoireadouts. With buttons that light up, settings can be verified at a glance.More Triggering FlexibilityHands-free triggering, made possible b ythe Auto-Level mode, automaticallyplaces a stable display of almost a n ywaveform on screen. The L F. H F, an tNoise Reject modes, together with i10-to-l holdoff range, deliver stable trig­gering on complex waveforms. The builtin TV Line and TV Field triggerinfcapability extends measurements to m osvideo-related applications with performance for the broadcast industry.Performance PlusThe NEW 2245 and 2246 oscilloscopeshave low-noise vertical systems that produce sharp, bright traces. Their 2-nst.inwbase and 100-MHz bandwidth bring outhe details on high-speed signals a n crender measurements with good tim W iresolution.Low-level signal measurements are easilymanaged by the 2 mV/div vertical sensitivity, even at full bandwidth, and by trig­ger sensitivity that extends to 0.25 di'T a50 MHz (1.0 div at 150 MHz).Voltage Measurements With the Pushof a ButtonA pushbutton-activated measuremensystem on the 2246 enhances productivi­ty even more. This scope turns out vitually hands-off measurements quickly-i-peak, -peak, peak-to-peak, dc,gated volts, all with convenient on-scrccreadout of values.[f more visual indication is desired, the unique cursor system can provide feed­back showing exactly where on the waveform an automatic measurement is being made. These feedback cursors, when selected, even show ground and trigger-level locations.There is also the ability to use cursors in the conventional manual mode for mak­ing point-to-point time and voltage measurements, including time-interval measurements between a point on the reference waveform and a point on any of four other displayed waveforms. Three-Year WarrantyAs with all of our high quality 2000 Series Oscilloscopes, the 2245 and 2246 (includ­ing the CRT) are covered by the Tektronix three-year instrument warranty, making ownership more cost effective than ever.CHARACTERISTICS Characteristics are common to both the 2245 and 2246, except where indicated.VERTICAL SYSTEMDisplay Modes—CH 1. CH 2, CH 2, CH 4, Add (CH 1+CH 2), Invert (CH 2), Alternate and Chopped display switching for all channels, and 20-MHz bandwidth limitingCHANNEL 1AND CHANNEL 2 Frequency Response (- 3 dB Bandwidth)—100 MHz: 0 to + 35°C; 90 MHz: +35 to + 50°C A C Coupled Lower -3 dB Frequency—10 Hz or less with IX probe. 1Hz or less with stan­dard accessory 10X probe.Step Response—s 3.5 ns for temperatures from 0 to +35°C. <3.9 ns for temperatures from +35 to +50°C (rise times calculated from: tr*=0.35/BW).Deflection Factor Range—2 mV'div to 5 V/div in a 1-2-5 sequence of 11steps.Maximum Error—±2% 15 to 35°C (add ±1% from 0 to 15 °C and from 35 to 50°C). Variable Range—Continuously variable be­tween Volts/Div step settings. Increases step setting by at least 2.5 Vdiv.Uncalibrated Indicators—>symbol appears on-screen when deflection factor is between calibrated Volts/Div step settings.Channel Isolation—50 dB or more attenua­tion of deselected channel at 10 MHz. 34 dB or more at 100 MHz (measured with an eight div input signal and equal Volts/Div settings on both channels from 2 mV/div to 0.5 Vdiv). CH 2 Signal Delay With Respect to CH 1 —< lot) ps difference.Input C haracteristics—1M0 ±0.15% shunted by 20 pF +0.5 pF. Maximum Input Voltage: 400 V (dc + peak ac): 800 V ac p-p at 10kHz or less.Common-Mode Rejection Ratio (ADD Mode W ith CH 2 Inverted)—At least 10:1 at 50 M Hz. (for common-mode signals of eight div or less ami with Var Volts/Div control adjusted for best U M R R at 50 kHz at any Volts/Div setting).Trace Drift—Between Volts/Div Step Settings:0.2 div or less. Var Volts/Div Rotated BetweenExtremes: 1div or less. Inverting CH 2: 1divor less. Between Gnd and DC Input Coupling:<0.5 m V from 0 to +35°C; <2 mV from 35 to50 °C.Position Range—At least ±11 div fromgraticule center.CHANNEL 3 AND CHANNEL 4Frequency Response—Same as CH 1 and CH 2.Step Response—Same as CH 1and CH 2.Deflection Factor—Settings: 0.1 V/div and 0.5V/div.Maximum Error—Same as CH 1and CH 2.CH Isolation—34 dB or more attenuation ofdeselected channel at 100 MHz (measured withan eight div input signal).CH 4 Signal Delay With Respect to CH 3—<100 ps difference.Input Characteristics—1 M fi ±1% shunted by2 pF ±0.5 pF (maximum Input Voltage: 400 V(dc + peak ac): 800 V p-p ac at 10 kHz or less)Trace Shift—Between Volts- Div Settings: 1 divor less.Position Range—Same as CH 1and CH 2.A LL CHANNELSLow Frequency Linearity—<0.06 div com­pression or expansion of a 2 div, center-screensignal when positioned anywhere within thegraticule area.Bandwidth Limiter—Reduces upper -3 dBbandpass to a limit of 17 to 23 MHz.Trace Separation Range—±4 div.Chop Mode Switching Rate—625 kHz± 10'7,.CH 3 or CH 4 Signal Delay With Respect toEither CH1or CH2—<200 ps difference.H O R IZO N TA L SYSTEMDisplay Modes—A (main sweep), A Alternatewith B (delayed sweep), and B. In X-Y mode,CH 1provides X-axis (horizontal) deflection.A Sweep Time Base Range—0.5 s/div to20 ns/div in a 1-2-5 sequence of 24 steps. X10magnification extends fastest sweep rate to 2ns/div.B Sweep Time Base Range—5 ms/div to 20ns/div in a 1-2-5 sequence of 21 steps. X10magnification extends fastest sweep rate to 2ns/div.Variable Timing Range—Continuouslyvariable between Sec Div calibrated step set­tings. Extends slowest A sweep and B sweepspeeds by a factor of a least 2.5 times. Affectsthe A Sec Div setting with the A display mode:affects the B Sec/Div setting with the Alt andB modes.A Sweep Timing Accuracy*1Range Unmagnified Magnified+ 15 to +35X:±2%±3%0 to +15°C+35 to +50°C±3%±4%*' Applies over the nmter eight div. Edrludesthe f irst 0.25 div of the magnifietl sivoep andsweep be g ood the 100th magnified div.Linearity— ±5% over any two of the centereight div, on both unmagnified andmagnified displays.Delay Time—Range: <0.1 div to >10 divof the A sweep. (Maximum value does notexceed end of the A sweep.) Jitter: 1:20,000p-p (0.005%) (viewed over two seconds).ATime—Range: 0 to >9.9 div to right of thedelay time setting (does not exceed end ofthe A sweep) Accuracy: ±(0.5% of reading+ 1%of one A sweep div).TRIGGERINGTrigger Sensitivity from CH 1, CH 2. CH 3.CH 2 Source.DC Coupled—0.35 div or greater triggersfrom dc to 50 MHz, increasing to 1 div at 150MHzNoise Reject Coupled—0.8 div or more trig­gers; 0.5 div or less does not trigger.HF Reject Coupled—0.35 div or greatertriggers from dc to 50 kHz; 0.25 div or lessdoes not trigger above 500 kHz.LF Reject Coupled—0.35 div or greatertriggers from 100 kHz to 50 MHz: 0.35 divor greater does not trigger from dc to 10 kHz.AC Coupled—0.35 div or greater triggersfrom 50 Hz and 50 MHz: 0.35 div or less doesnot trigger from dc to 5 Hz.For dc. LF Reject, and ac coupling above 50MHz, triggering signal requirement increasesto 1.0 div at 150 MHz.Trigger Sensitivity From TV Line or TVField Source—0.5 div or less of compositesync achieves stable display.Lowest Usable Frequency With AutoLevel Function—10 H z.Level Control Range—±20 div (referenc­ed to the selected source).Level Readout Accuracy—±(0.3% of read­ing + 0.1 div).Variable Holdoff Range—Increases the Asweep holdoff time by at least a factor of 10.X-Y OPERATIONDeflection Factors—Same as verticalsystem (Var Volts/Div in calibrated detent).Maximum ErrorR ange Y-Axis X-Axis+ 15 to +35°C±2%+3%0 to +15°C+35 to +50°C+3°/o r4°/oX-Axis - 3 dB Bandwidth—3 M H z or morePhase Difference Between X and Y—< 3 0(for dc coupled signals from dc to 50 kHzwith bandwidth limiter off).CURSOR AND FRONT PANEL DISPLA YControls—Separate A Intensity. B Intensi­ty, Readout Intensity, Focus, Beam Finder.Trace Rotation, and Scale Illumination.C R T—8x 10 cm internal graticule. Markings:8 major div vertically and 10 major divhorizontally, with auxiliary markings.Standard Phosphor—G H(P31).Y-Axis Orthogonality—<0.1 div over eightvertical div; no adjustment.With complimentsHelmut Singer Elektronikwww.helmut-singer.de *********************fon +49 241 155 315 fax +49 241 152 066Feidchen 16-24 D-52070 Aachen GermanyWith complimentsH elm ut Singer E lektronikwww.heimut-singer.de *********************fon +49 241 155 315 fax+49 241 152 066Feldchen 16-24 D-52070 Aachen GermanyCursor FunctionsFunction AccuracySec: 1/Sec: Phase; ATime. Ai/Tim e. APhase ±(0.5°/o of read­ing +0.02 horizontal div)Volts; G round Volts (2246 only)±(0.5%of read­ing +0 02 vertical d iv+H F display errors)Function PositionAccuracy*1Track Measurement. Trig Level Ground (2246 only)±005 vertical div*' Cursor position on waveform vs readout displayed value.EXTERNAL Z-AXIS INPUTActive Region Lower Threshold—<1.8 V. Signal Required to Blank Sweep-Related L Trace—>3.8 V.Input Resistance to Ground—10 kO ±10%. Maximum Input Voltage—30 V(dc + peak ac) or <30 V ac p-p at 1kHz.C A L IB R A T O R OUTPUTVoltage Into 1-Mfi Load—0.5 V±2%. Repetition Range—1kHz +10%. Overshoot— <0.1%.POW ER REQUIREM ENTSLine Voltage Range—90 to 250 V acLine Frequency—48 to 445 H z.Fuse Rating—2 A. 250 V, slow-blow. Maximum Power Consumption—80 W (110 V ac).ENVIRO NM EN TAL Environmental requirements qualify the elec­trical and mechanical specifications. When not rackmounted, the instrument meets the en­vironmental capabilities of a Type 111, Class 3, Stvle D instrum ent as prescribed by MIL-T-28800C.Ambient Temperature—Operating: 0 to -50°C. Nonoperating: -50 to -75°C. Altitude—Operating: To 4500 m (15,000 ft). Maximum operating temperature decreases 1°C for each 300 m (1.000 ft) above 1500 m (5000 ft). Nonoperating: to 15 250 m (50,000 ft).Vibration—Operating: 15 minutes along each of three axes. 0.015 inch p-p displacement. 10 to 55 Hz in one minute sweeps. Held for 10 min­utes at 55 Hz (2.4 g's at 55 Hz). Humidity—Operating and Nonoperating: 95%, five cycles (120 hours) referenced to M IL- T-28800C, Paragraph 4.5.5.1.2.2 for Type III, Class 3.Shock—Operating and Nonoperating: 30 g, half sine, 11-ms duration; three shocks on each face, for a total of 18 shocks.Bench Handling Test—4 inch drop per Tek­tronix Standard 062-2858-00. Transportation Drop and Vibration—Meets the limits of Tektronix Standard 062-2858-00.PHYSICAL CHARACTERISTICSDimensions mm In.Width w/handle36114.2Height w/feet & pouch1777.0w/o pouch164 6.4Depth w/front cover44517.5w/handle extended519204Weight.kg lbNet w/accessories & pouch8.919 6w/o accessories & pouch7.917.42246With VoltmeterDC Volts—Accuracy: ±(0.3% of reading +0.02div). Normal Mode Rejection Ratio: >50 dB at50 and 60 Hz.+ Peak and - Peak Volts—Accuracy: ±(2% ofreading +0.1 div) for signals from 20 Hz to 30MHz. -3 dB at 100 MHz. Gated Region Mini­mum Width: <(0.2 div +50 ns).P-P Volts—Accuracy: ±(2% of reading +0.1div) for signals from 20 Hz to 30 MHz. -3 dBfrom 30 to 100 MHz. Gated Region MinimumWidth: <(0.2 div +50 ns).ORDERING INFORMATION2245— 100 MHz OscilloscopeIncludes:—Two 10X, 1.5 m probes with ac­cessories (P6109 Opt 01): clear accessoriespouch (016-0537-00); blue plastic CRT filter(337-2775-00); 2A, 250 V fuse (159-0023-00);Operator Manual (070-6276-00).2246— 100 MHz Oscilloscope with Voltmeter,ATime, and SmartCursors™Includes:—Two 10X, 1.5 m probes w/ac-cessories (P6109 Opt. 01); clear accessoriespouch (016-0537-00); blue plastic CRT filter(337-2775-00); 2 A, 250 V fuse (159-0023 00);Operator’s Manual (070-6083-00); UserReference Guide (070-6081-00).OPTIONSOption 02—Protective front panelcover and accessory pouch.Option 1C—C-5C Option 02Camera.Option IK—K212 Portable Instru­ment Cart.Option IT—Transit Case.Option 22—Two additional P6109probes.Option 23—Two 1X/10X P6062B, 6ft probes.INTERNATIONAL POW ER PLUG OPTIONSOption A1—Universal Euro 220 V, 50 Hz.Option A2—UK 240 V, 50 Hz.Option A3—Australian 240 V, 50 Hz.Option A4—North American 240 V, 60 Hz.Option A5—Switzerland 220 V, 50 Hz.W ARRAN TY-PLU S SERVICE PLANSM l—(2245) 2 Calibrations.M l—(2246) 2 Calibrations.M2—(2245) 2 Years Service.M2—(2246) 2 Years Service.M3—(2245) 2 Years Serviceand 4 Calibrations.M3—(2246) 2 Years Serviceand 4 Calibrations.M4—(2245) 5 Calibrations.M4—(2246) 5 Calibrations.M5—(2245) 9 Calibrations +2 Years Service.M5—(2246) 9 Calibrations +2 Years Service.OPTIONAL ACCESSORIESService Manual(2245/2246) Order 070-6081-00Front Panel Cover—Order200-3232-00Accessory Pouch—Order016-0857-00Accessory Pouch and Cover-Order 020-1515-00Protective Waterproof VinylCover—Order 016-0848-00Viewing Hoods—(Collapsible) Order 016-0592-00(Binocular) Order 016-0566-00(Polarized) Order 016-0180-00Clear Implosion Shield—Order337-2775-01Carrying Strap—Order346-0199-00Carrying Case—Order016-0792-01 •>Clear Graticule Filter—Order337-2775-011107 DC Inverter—See page 3331106 Battery Pack—See page 3321105 Power Supply—See page 332*1Recommend use with front panel cover(200-2520-00).RECOM M ENDED PROBESSee Probe Section for additional probe?The P6062B allows switching between IX and10X attenuation. Readout display changes withattenuation switching.P6109 (Opt 01)—10X Probe.P6062B—1X-10X Probe.P6008—Environmental Probe.P6009—High Voltage Probe.P6202A—Active Probe.1101A—Active Probe Power Supply.A6302—Current Probe.A6303—Current Probe.AM 503—Current Probe Amplifier.A6901 Ground Isolation Monitor—See Accessories Section.A6902B Isolator—See AccessoriesSection.RECOM M ENDED CAM ERASC-5C Option 02 —See AccessoriesSection.C-7 Option 03—See AccessoriesSection.C-4—See Accessories Section.RECOM M ENDED CAR TK212—For on-site mobility.SeeAccessories Section.。