下载文档原格式
材料成型工艺基础部分(中英文词汇对照)材料成型工艺基础部分0 绪论金属材料：metal material (MR)高分子材料：high-molecular material陶瓷材料：ceramic material复合材料：composition material成形工艺：formation technology1 铸造铸造工艺：casting technique铸件：foundry goods （casting）机器零件：machine part毛坯：blank力学性能：mechanical property砂型铸造：sand casting process型砂：foundry sand1.1 铸件成形理论基础合金：alloy铸造性能：casting property工艺性能：processing property收缩性：constringency偏析性：aliquation氧化性：oxidizability吸气性：inspiratory铸件结构：casting structure使用性能：service performance浇不足：misrun冷隔：cold shut夹渣：cinder inclusion粘砂：sand fusion缺陷：flaw, defect, falling流动性：flowing power铸型：cast (foundry mold)蓄热系数：thermal storage capacity 浇注：pouring凝固：freezing收缩性：constringency逐层凝固：layer-by-layer freezing 糊状凝固：mushy freezing结晶：crystal缩孔：shrinkage void缩松：shrinkage porosity顺序凝固：progressive solidification 冷铁：iron chill补缩：feeding等温线法：constant temperature line method 内接圆法：inscribed circle method铸造应力：casting stress变形：deforming裂纹：crack机械应力：mechanical stress热应力：heat stress相变应力：transformation stress气孔：blow hole铸铁：ingot铸钢：cast steel非铁合金：nonferrous alloy灰铸铁：gray cast-iorn孕育处理：inoculation球墨铸铁：spheroidal球化处理：sheroidisation可锻铸铁：ductile cast iron石墨：graphite蠕墨铸铁：vermicular cast iron热处理：heat processing铝合金：Al-alloy熔炼：fusion metallurgy铜合金：copper alloy氢脆：hydrogen brittleness1.2 铸造方法（casting method）手工造型：hand moulding机器造型：machine moulding金属型：metal mold casting金属模：permanent mould压力铸造：press casting熔模铸造：investment moulding蜡膜：cere离心铸造：centrifugal casting低压铸造：casting under low pressure 差压铸造：counter-pressure casting 陶瓷型铸造：shaw process1.3 铸造工艺设计浇注位置：pouring position分型面：mould joint活块：loose piece起模：patter drawing型芯：core型芯撑：chaplet工艺参数：processing parameter下芯：core setting合型：mould assembly冒口：casting head尺寸公差：dimensional tolerance尺寸公差带：tolerance zone机械加工余量：machining allowance 铸孔：core hole非标准：nonstandard label收缩率：rate of contraction线收缩：linear contraction体收缩：volume contraction起模斜度：pattern draft铸造圆角：curving of castings芯头：core register芯头间隙：clearance芯座：core print seat分型线：joint line分模线：die parting line1.4 铸造结构工艺性加强筋：rib reinforcement撒砂：stuccoing内腔：entocoele2 金属塑性加工塑性加工：plastic working塑性：plastic property锻造：forge work冲压：punching轧制：rolling拉拔：drawing挤压：extruding细化晶粒：grain refinement热锻：hit-forging温锻：warm forging2.1 金属塑性加工理论基础塑性变形：plastic yield加工硬化：work-hardening韧性：ductility回复温度：return temperature 再结晶：recrystallize再结晶退火：full annealing冷变形：cold deformation热变性：heat denaturation锻造比：forging ratio镦粗：upset拔长：pull out纤维组织：fibrous tissue锻造性能：forging property可锻性：forgeability变形抗力：resistance of deformation化学成分：chemical constitution热脆性：hot brittleness冷脆性：cold-shortness变形速度：deformation velocity应力状态：stress condition变形温度：deformation temperature过热：overheating过烧：burning脱碳：carbon elimination始锻温度：initiation forging temperature 终锻温度：final forging temperature2.2 金属塑性加工方法自由锻：flat-die hammer冲孔：jetting弯曲：bend弯曲半径：bending radius切割：cut扭转：twist rotation错移：offsetting锻接：percussion基本工序：basic process辅助工序：auxiliary process精整工序：finishing process模锻：contour forging锻模：forging die胎膜锻：fetal membrane forging剪床：shearing machine冲床：backing-out punch冲裁：blanking弹性变形：elastic distortion塑性变形：plastic yield剪切变形：shearing deformation最小弯曲半径：minimum bending radius 曲率：angularity弯裂：rupture回弹：rebound辊轧：roll forming辊锻：roll forging斜轧：oblique rolling横轧：transverse rolling辗压：tamping drum挤压：extruding拉拔：draft2.3 塑性加工工艺设计工艺规程：process specification锻件图：forging drawing敷料：dressing锻件余量：forging allowance锻件公差：forging tolerance工夹具：clamping apparatus加热设备：firing equipment加热规范：heating schedule冷却规范：cooling schedule后续处理：after treatment分模面：die parting face冲孔连皮：punching the wad模锻斜度：draft angle圆角半径：radius of corner圆饼类锻件：circumcresent cake-like forging 长轴类锻件：long axis-like forging2.4 锻件结构工艺性锥体：cone斜面：cant空间曲线：curve in space粗糙度：degree of roughness2.5 冲压件结构工艺性3 焊接焊接：welding铆接：riverting熔焊：fusion welding压焊：press welding钎焊：braze welding3.1 焊接理论基础冶金：metallurgy电弧焊：arc welding气焊：acetylene welding电渣焊：electro-slag welding高能束焊：high energy welding 电子焊：electronic welding激光焊：laser welding等离子焊：plasma welding电弧：electric arc阳极区：anode region阴极区：negative polarity弧柱区：arc stream正接法：electrode negative method反接法：opposition method脱氧剂：deoxidizing agent焊缝：welded seam焊缝区：weld zone熔合区：fusion area热影响区：heat-affected zone脆性断裂：brittle fracture过热区：overheated zone正火区：normalized zone相变区：phase change zone焊接应力：welding stress收缩变形：contraction distortion角变形：angular deformation弯曲变形：bend deformation扭曲变形：warping deformation波浪变形：wave transformation反变形法：reversible deformation method 刚性固定法：rigid fixing method预热：warming-up缓冷：slow cool焊后热处理：postweld heat treatment矫形处理：shape-righting3.2 焊接方法埋弧焊：hidden arc welding气体保护焊：gas shielded arc welding氩弧焊：argon welding熔化极氩弧焊：consumable electrode argon welding 钨极氩弧焊：argon tungsten-arc welding二氧化碳气体保护焊：CO2 gas shielded arc welding 碳弧焊：carbon arc welding碳弧气刨：carbon arc air gouging电渣焊：electro-slag welding高能焊：high grade energy welding等离子弧切割：plasma arc cutting (PAC)堆焊：bead weld电阻焊：resistance welding电焊：electric welding缝焊：seam welding压焊：press welding多点凸焊：multiple projection welding对焊：welding neck摩擦焊：friction welding扩散焊：diffusion welding硬钎料：brazing alloy软钎料：soft solder3.3 常用金属材料的焊接焊接性：weldability焊接方法：welding method 焊接材料：welding material 焊条：electrode焊剂：flux material碳素钢：carbon steel低碳钢：low carbon steel中碳钢：medium carbon steel 高碳钢：high carbon steel低合金钢：lean alloy steel不锈钢：non-corrosive steel 有色金属：nonferrous metal 3.4 焊接工艺设计型材：sectional bar药皮：coating焊丝：soldering wire连续焊缝：continuous weld断续焊缝：intermittent weld应力集中：stress concentration焊接接头：soldered joint坡口：groove对接：abutting joint搭接：lap joint角接：corner joint4 粉末冶金（power metallurgy）粉末冶金成品：finished power metallurgical product 铁氧体：ferrite硬质合金：sintered-carbide高熔点金属：high-melting metal陶瓷：ceramic4.1 粉末冶金工艺理论基础压坯：pressed compact扩散：diffusion烧结：agglomeration固溶：solid solubility化合：combination4.2 粉末冶金的工艺流程制备：preparation预处理：anticipation还原法：reduction method电解法：electrolytic method雾化法：atomization粒度：grain size松装密度：loose density流动性：flowing power压缩性：compressibility筛分：screen separation混合：compounding制粒：pelletization过烧：superburning欠烧：underburnt5 金属复合成型技术自蔓延焊接：SHS welding热等静压：HIP准热等静压：PHIP5.1 液态成型技术与固态成型技术的复合高压铸造：high-pressure casting电磁泵：magnetic-pump压射成型：injection molding柱塞：plunger piston冲头：drift pin凝固法：freezing method挤压法：extrusion method转向节：knuckle pivot制动器：arresting gear5.2 金属半凝固、半熔融成型技术凝固：freezing半熔融：semi-vitreous触变铸造：thixotropy casting触变锻造：thixotropy forging注射成型：injection molding5.3 其他金属成型新技术快速凝固：flash set非晶态：amorphous溢流法：press over system喷射沉积：ejecting deposit爆炸复合法：explosion cladding method 扩散焊接：diffusion welding挤压：extruding轧制：roll down6 非金属材料成型技术6.1 高分子材料成型技术高分子材料：non-metal material耐腐蚀：resistant material绝缘：insulation老化：ageing耐热性：heat-durability粘弹性：viscoelasticity塑料：plastic material橡胶：rubber合成纤维：synthetic fibre涂料：covering material粘结剂：agglomerant粘度：viscosity热塑性塑料：thermoplastic plastics 热固性塑料：thermosetting plastic 通用塑料：general-purpose plastics 工程塑料：engineering plastic薄膜：thin film增强塑料：reinforced plastics浇注塑料：pouring plastics注射塑料：injiection plastics挤出塑料：extrusion plastics吹塑塑料：blowing plastics模压塑料：die pressing plastics聚合物：ploymer semiconductor吸湿性：hygroscopic cargo定向作用：directional action生胶：green glue stock填料：carrier丁苯橡胶：SBR顺丁橡胶：BR氯丁橡胶：CR丁腈橡胶：NBR硅橡胶：Q聚氨酯橡胶：U压延：calender硫化：sulfuration胶粘剂：adhesive胶接：glue joint刹车片：brake block零件修复：parts renewal蜂窝夹层：honeycomb core material 6.2 工业陶瓷制品的成型技术干燥：drying坯料：blank润滑剂：anti-friction结合剂：binder热压铸：hot injiection moulding 6.3 非金属材料成型技术的新进展热压烧结：hot pressed sintering7 复合材料的成型技术复合材料：composite material树脂：resin7.1 金属复合材料的成型技术硼纤维：boron fiber钛合金：titanium alloy碳纤维：carbon filter等离子喷涂：plasma spraying浸渍法：immersion method锭坯：ingot blank7.2 聚合物基复合材料的成型技术晶须：whisker缠绕成形：enwind forming湿法缠绕：wet method enwind 7.3 陶瓷复合材料成型技术料浆：slurry溶胶-凝胶法：sol-gel method化学气相沉积：chemical vapor deposition (CVD) 原位：in situ8 材料成型方法的选择粉末冶金：powder metallurgy工程塑料：engineering plastics工程陶瓷：engineering ceramics。
![材料成型及控制工程专业英语词汇表[借鉴]](https://uimg.taocdn.com/2414d376dcccda38376baf1ffc4ffe473368fd1f.webp)
Unit One arbitrary:任意的，武断的，专制的invariably：不变的，一定的sharply：剧烈的electrical power：电源blast furnace：高炉coke：焦炭Iron ore：铁矿石limestone：石灰石reduction：还原反应slag：炉渣tap：阀门,出渣口Property：Load support：pig iron：生铁cupola：化铁炉ladle：钢水包Fule：燃料Flux：溶剂mold：模具tension：拉力intricate：复杂的negligible：微不足道的wrought iron：锻铁，熟铁Free graphite：自由石墨flack graphite：片状的石墨mild steel：低碳钢ferrous alloy：铁合金moderately priced：价格适中ductile：延展Elastic：弹性durable：耐用的non-ferrous：eminently practical：非常实用ball bearings：滚珠轴承metal sheet：金属板AISI：code designation：规定牌号plain steel：碳素钢approximate：近似的high strength low alloy steel：高强度低合金钢proprietary：专卖的specified：规定的,详细说明的optimal：最佳的，最理想的hot rolling：热轧elevated：提高的stress relief：应力消除justification：理由，superalloy：超耐热高应力耐蚀合金rust：生锈chromium：铬austenite：奥氏体nickel：镍ferritic stainless steel：铁素体不锈钢serviceable：可以使用的quench：淬火body centered tetragonal crystal structure：体心四方晶体结构yield high strength：产生高强度cutlery：刀具，餐具spring：弹簧precipitation hardening：沉淀硬化essentially：本质上dislocation motion：位错运动corrosion resistance structural members：耐腐蚀结构件tungsten：钨molybdenum：钼chromium：铬dual：双重的heat resistance：耐热的cobalt：钴oxidation：氧化justifying：证明，，，有理severe：严峻的carbide formation kinetics：碳化物形成动力学viscosities：粘性surface flim：表面膜shrinkage：收缩solidifacation：凝固inferior：差的uniform：统一的，均衡的porosity：有孔的forge：锻造simple shape：简单断面型钢white iron：白口铸铁crystalline fracture surface：结晶断面gray iron：灰口铸铁significant：有效的，有意义的precipitation：沉淀flakes：片状的magnesium：镁spheroidal：球状的ductile iron：球墨铸铁by a factor of 20：是原来的20倍malleable iron：可锻铸铁nodular graphite：球形石墨equivalent：等价的Welding:焊接Consult：查阅Scientific literature：科学文献Symbol：符号Topic：话题Corresponding author：通讯作者Keywords：关键词Abstract：摘要Classification number：中图分类号Reference：参考文献Retrieval word：检索词Background：研究背景Correlation：相关性，关联Unit threeLesson one Manufacturing:v.生存、制造；n.制造业；Shapeless：不成型的、不定型的；Accuracy：精度；Tolerance：公差；Classification：类别；Assemble：装配；Metallurgy：A simplifide manner：简化的方式；Melt extrusion：熔融挤出；Die casting：模具铸造，压力铸造、拉模铸造；Pressing of metal powder：金属粉末压制；Rolling：轧制；Extrusion：挤压；Formulation:Cold and hot forging：冷锻/自由锻和热锻；Deep drawing：拉深（深冲压）；Sawing：锯切；Plastic deformation：Turning：车削；Milling：铣削；Broaching：拉削、绞孔、扩孔；Removing metal：Blacksmith：铁匠；Locksmith：Grind/graind：磨；Metal treatment processes：金属处理工艺；Heat treating：Anodizing：阳极氧化处理；Surface hardening：表面硬化；Essentially：本质上；Joining processes：连接；Metallurgical joining：冶金连接；Welding：焊接；Diffusion bonding：扩散接合；Riveting：铆接；Mechanical：Shrink fitting：预紧（过盈）装配；Production rates：生产率；Capable：有能力的；Recrystallization temperature：Extraordinary cost：额外成本；Die set：模座；Varible：可变因素，变量；Dimensional：空间的，尺寸的；Specified：规定的，详细说明的；Dimensional tolerance：尺寸公差；Surface finish：表面光洁度；Quality：质量；Sophisticated：复杂的；Variation：变化；Means of new development：新开发的手段；Lost wax vacuum casting：失蜡真空铸造；Tighter tolerance：更严格的公差；Brake drum：刹车鼓；Vibration：震动；Interchangeability：可替换性；Defective：有缺陷的；Modern mass production：现代大规模生产；Indicate：表明，指出；Gross national product：国民生产总值；Manufacturing industries：制造业；Manufacturing productivity：制造业的生存率；Discrete parts：分立零件；Ingredient：原料，要素，组成部分；Human and managerial resource：人力及管理资源；Plant：工厂，车间；Interface：相互作用；Physiological：生理学的；Psychological：心理学的；Precede：领先，在。
机械工业冲压工程术语标准冲压1 冲压工艺1.1 冲压sheet metal forming靠压力机和模具对板材、带材、管材及型材等施加外力，使之产生塑性变形或分离，从而获得所需形状和尺寸的冲压件成形加工方法。
1.2 冲压件 stamping采用冲压方法制成的工件或毛坯。
1.3 金属压力加工 mechanical working of metals利用金属的塑性，使其改变形状、尺寸和改善性能，以获得型材、棒材、板材、线材、锻件、冲压件的加工方法。
1.4 板料成形 sheet forming用板料、薄壁管、薄型材等作为原材料进行塑性加工的冲压方法。
1.5 冲压工艺路线 process chart of press按产品或零部件的冲压工艺编制的说明产品、零部件的工序、工序名称、工序内容、工艺参数、采用的设备和工艺装备等的工艺文件。
1.6 冲裁 blanking利用冲模将板料以封闭的轮廓与坯料分离的冲压方法。
1.7 落料 blanking利用冲裁取得一定外形制件或坯料的加工方法。
1.8 冲孔punching将坯料内的材料以封闭曲线和坯料分离开来，得到带孔制件的冲压方法。
1.9 切断 cut-off将坯料或工件切成两段或数段的冲压方法。
1.10 切口 notch将材料沿不封闭的曲线部分地分离开，其分离部分和材料发生形状变化的冲压方法。
1.11 切边 side scrap将拉深或成型后的半成品边缘部分多余材料切掉的冲压方法。
1.12 精密冲裁 fine blanking用压边圈使板料冲裁区处于静压作用下，抑制剪裂纹的发生，实现塑性变形分离的冲裁方法。
1.13 负间隙冲裁 negative clearance blanking在凸模直径大于凹模直径的模具内进行的冲裁方法。
1.14 对向凹模冲裁 opposed die blanking利用一个平端面凹模和一个带凸台的凹模使材料实现分离与整修的冲裁方法。
1.15 整修 shaving整修模沿冲裁件的外缘或内孔刮去一层薄薄的切屑，以提高冲裁件的加工精度和剪断面光洁度的加工方法。
1.1 制造工艺我们如今所享受到的文明的好处从本质上来说是源于我们所能利用的产品质量的提高。
产品质量的提高可以通过包括功能和制造方面的需求的合理设计来获得。
设计过程会合理的考虑使用同样理想的制造工艺。
这可以保证产品在经济的成本下制得。
制造就是将未加工的材料转变为为某种目的而使用的成品。
以往我们对材料的一些外部性能如耐高温，耐高速，和高负荷的要求不断提高这反过来也需要一系列的新材料和与之关联的工艺过程。
而且，现代工业操作所需要的外部环境也对制造工业有很大要求。
而且制造过程的经济性是一个很重要的考量，为了在现代环境侠可行，一件产品必须在出功能与美学要求外完全定价。
所以对一个工程师来说考虑到制造的各个方面是必须的。
制造工艺是一个很基础的课题，因为他不仅涉及到制造工程师的利益，事实上也关乎几乎所有工程学科的利益。
之所以如此是因为工程是一个为人类消费提供各种材料的整体。
对许多如化学工业，文职，电力，电气，纺织等需要的工业机器制造工艺都是至关重要的部分、因此对制造工艺的详尽的了解对每一个工程师来说都是必要的。
这可以帮组他来判别各种制造工艺的性能，优缺点。
这反过来也对他对所需产品的合理设计有所帮助。
首先他能够从它的设计来评估制造的可行性。
他也可以找到不止一种制造过程来生产一件特殊的产品，从而对能以最低的制造成本来造出所需质量的产品的工艺做出合理的选择。
他也可以轻微地修改它的设计部来适应他所选择的制造工艺。
制造被韦伯词典定义为：制造出可供使用的产品。
直到18世纪末的第一次工业革命制造仍然被定义为生产小体积，低价格的产品的手工工艺。
个别的部件的生产和整体装配需要高度熟练的手工艺。
在任何机器都没有的情况下，缓慢而昂贵是唯一可能发生的情况，蒸汽机和燃煤火炉的使用使大量蒸汽驱动的机器被发明，从而极大增加制造能力。
这一时期出现了大量与机器有关的发明，并持续至19世纪末。
至19世纪末随着电力和更好的工程材料的发明，机器操作变得更具生产力。
Unit One arbitrary:任意的，武断的，专制的invariably：不变的，一定的sharply：剧烈的electrical power：电源blast furnace：高炉coke：焦炭Iron ore：铁矿石limestone：石灰石reduction：还原反应slag：炉渣tap：阀门,出渣口Property：Load support：pig iron：生铁cupola：化铁炉ladle：钢水包Fule：燃料Flux：溶剂mold：模具tension：拉力intricate：复杂的negligible：微不足道的wrought iron：锻铁，熟铁Free graphite：自由石墨flack graphite：片状的石墨mild steel：低碳钢ferrous alloy：铁合金moderately priced：价格适中ductile：延展Elastic：弹性durable：耐用的non-ferrous：eminently practical：非常实用ball bearings：滚珠轴承metal sheet：金属板AISI：code designation：规定牌号plain steel：碳素钢approximate：近似的high strength low alloy steel：高强度低合金钢proprietary：专卖的specified：规定的,详细说明的optimal：最佳的，最理想的hot rolling：热轧elevated：提高的stress relief：应力消除justification：理由，superalloy：超耐热高应力耐蚀合金turbine blade：涡轮叶片rust：生锈chromium：铬austenite：奥氏体nickel：镍ferritic stainless steel：铁素体不锈钢serviceable：可以使用的quench：淬火body centered tetragonal crystal structure：体心四方晶体结构yield high strength：产生高强度cutlery：刀具，餐具spring：弹簧precipitation hardening：沉淀硬化essentially：本质上dislocation motion：位错运动corrosion resistance structural members：耐腐蚀结构件tungsten：钨molybdenum：钼chromium：铬dual：双重的heat resistance：耐热的cobalt：钴oxidation：氧化justifying：证明，，，有理severe：严峻的turbojet：涡轮喷气飞机carbide formation kinetics：碳化物形成动力学viscosities：粘性surface flim：表面膜shrinkage：收缩solidifacation：凝固inferior：差的uniform：统一的，均衡的porosity：有孔的forge：锻造simple shape：简单断面型钢white iron：白口铸铁crystalline fracture surface：结晶断面gray iron：灰口铸铁significant：有效的，有意义的precipitation：沉淀flakes：片状的magnesium：镁spheroidal：球状的ductile iron：球墨铸铁by a factor of 20：是原来的20倍malleable iron：可锻铸铁nodular graphite：球形石墨equivalent：等价的Welding:焊接Consult：查阅Scientific literature：科学文献Symbol：符号Topic：话题Corresponding author：通讯作者Keywords：关键词Abstract：摘要Classification number：中图分类号Reference：参考文献Retrieval word：检索词Background：研究背景Correlation：相关性，关联Unit threeLesson one Manufacturing:v.生存、制造；n.制造业；Shapeless：不成型的、不定型的；Accuracy：精度；Tolerance：公差；Classification：类别；Assemble：装配；Metallurgy：A simplifide manner：简化的方式；Melt extrusion：熔融挤出；Die casting：模具铸造，压力铸造、拉模铸造；Pressing of metal powder：金属粉末压制；Rolling：轧制；Extrusion：挤压；Formulation:Cold and hot forging：冷锻/自由锻和热锻；Deep drawing：拉深（深冲压）；Sawing：锯切；Plastic deformation：Turning：车削；Milling：铣削；Broaching：拉削、绞孔、扩孔；Removing metal：Blacksmith：铁匠；Locksmith：Grind/graind：磨；Metal treatment processes：金属处理工艺；Heat treating：Anodizing：阳极氧化处理；Surface hardening：表面硬化；Essentially：本质上；Joining processes：连接；Metallurgical joining：冶金连接；Welding：焊接；Diffusion bonding：扩散接合；Riveting：铆接；Mechanical：Shrink fitting：预紧（过盈）装配；Production rates：生产率；Capable：有能力的；Recrystallization temperature：Extraordinary cost：额外成本；Die set：模座；Varible：可变因素，变量；Dimensional：空间的，尺寸的；Specified：规定的，详细说明的；Dimensional tolerance：尺寸公差；Surface finish：表面光洁度；Quality：质量；Sophisticated：复杂的；Variation：变化；Means of new development：新开发的手段；Lost wax vacuum casting：失蜡真空铸造；Tighter tolerance：更严格的公差；Brake drum：刹车鼓；Vibration：震动；Interchangeability：可替换性；Defective：有缺陷的；Modern mass production：现代大规模生产；Indicate：表明，指出；Gross national product：国民生产总值；Manufacturing industries：制造业；Manufacturing productivity：制造业的生存率；Discrete parts：分立零件；Ingredient：原料，要素，组成部分；Human and managerial resource：人力及管理资源；Plant：工厂，车间；Interface：相互作用；Physiological：生理学的；Psychological：心理学的；Precede：领先，在。
材料成型工艺基础部分0 绪论金属材料：metal material (MR)高分子材料：high-molecular material陶瓷材料：ceramic material复合材料：composition material成形工艺：formation technology1 铸造铸造工艺：casting technique铸件：foundry goods （casting）机器零件：machine part毛坯：blank力学性能：mechanical property砂型铸造：sand casting process型砂：foundry sand1.1 铸件成形理论基础合金：alloy铸造性能：casting property工艺性能：processing property收缩性：constringency偏析性：aliquation氧化性：oxidizability—吸气性：inspiratory铸件结构：casting structure使用性能：service performance浇不足：misrun冷隔：cold shut夹渣：cinder inclusion粘砂：sand fusion缺陷：flaw, defect, falling流动性：flowing power铸型：cast (foundry mold)蓄热系数：thermal storage capacity浇注：pouring凝固：freezing收缩性：constringency逐层凝固：layer-by-layer freezing糊状凝固：mushy freezing结晶：crystal缩孔：shrinkage void缩松：shrinkage porosity顺序凝固：progressive solidification冷铁：iron chill补缩：feeding—等温线法：constant temperature line method内接圆法：inscribed circle method铸造应力：casting stress变形：deforming裂纹：crack机械应力：mechanical stress热应力：heat stress相变应力：transformation stress气孔：blow hole铸铁：ingot铸钢：cast steel非铁合金：nonferrous alloy灰铸铁：gray cast-iorn孕育处理：inoculation球墨铸铁：spheroidal球化处理：sheroidisation可锻铸铁：ductile cast iron石墨：graphite蠕墨铸铁：vermicular cast iron热处理：heat processing铝合金：Al-alloy熔炼：fusion metallurgy—铜合金：copper alloy氢脆：hydrogen brittleness1.2 铸造方法（casting method）手工造型：hand moulding机器造型：machine moulding金属型：metal mold casting金属模：permanent mould压力铸造：press casting熔模铸造：investment moulding蜡膜：cere离心铸造：centrifugal casting低压铸造：casting under low pressure差压铸造：counter-pressure casting陶瓷型铸造：shaw process1.3 铸造工艺设计浇注位置：pouring position分型面：mould joint活块：loose piece起模：patter drawing型芯：core型芯撑：chaplet工艺参数：processing parameter—下芯：core setting合型：mould assembly冒口：casting head尺寸公差：dimensional tolerance尺寸公差带：tolerance zone机械加工余量：machining allowance铸孔：core hole非标准：nonstandard label收缩率：rate of contraction线收缩：linear contraction体收缩：volume contraction起模斜度：pattern draft铸造圆角：curving of castings芯头：core register芯头间隙：clearance芯座：core print seat分型线：joint line分模线：die parting line1.4 铸造结构工艺性加强筋：rib reinforcement撒砂：stuccoing内腔：entocoele—2 金属塑性加工塑性加工：plastic working塑性：plastic property锻造：forge work冲压：punching轧制：rolling拉拔：drawing挤压：extruding细化晶粒：grain refinement热锻：hit-forging温锻：warm forging2.1 金属塑性加工理论基础塑性变形：plastic yield加工硬化：work-hardening韧性：ductility回复温度：return temperature再结晶：recrystallize再结晶退火：full annealing冷变形：cold deformation热变性：heat denaturation锻造比：forging ratio镦粗：upset—拔长：pull out纤维组织：fibrous tissue锻造性能：forging property可锻性：forgeability变形抗力：resistance of deformation化学成分：chemical constitution热脆性：hot brittleness冷脆性：cold-shortness变形速度：deformation velocity应力状态：stress condition变形温度：deformation temperature过热：overheating过烧：burning脱碳：carbon elimination始锻温度：initiation forging temperature终锻温度：final forging temperature2.2 金属塑性加工方法自由锻：flat-die hammer冲孔：jetting弯曲：bend弯曲半径：bending radius切割：cut—扭转：twist rotation错移：offsetting锻接：percussion基本工序：basic process辅助工序：auxiliary process精整工序：finishing process模锻：contour forging锻模：forging die胎膜锻：fetal membrane forging剪床：shearing machine冲床：backing-out punch冲裁：blanking弹性变形：elastic distortion塑性变形：plastic yield剪切变形：shearing deformation最小弯曲半径：minimum bending radius曲率：angularity弯裂：rupture回弹：rebound辊轧：roll forming辊锻：roll forging斜轧：oblique rolling—横轧：transverse rolling辗压：tamping drum挤压：extruding拉拔：draft2.3 塑性加工工艺设计工艺规程：process specification锻件图：forging drawing敷料：dressing锻件余量：forging allowance锻件公差：forging tolerance工夹具：clamping apparatus加热设备：firing equipment加热规范：heating schedule冷却规范：cooling schedule后续处理：after treatment分模面：die parting face冲孔连皮：punching the wad模锻斜度：draft angle圆角半径：radius of corner圆饼类锻件：circumcresent cake-like forging长轴类锻件：long axis-like forging2.4 锻件结构工艺性—锥体：cone斜面：cant空间曲线：curve in space粗糙度：degree of roughness2.5 冲压件结构工艺性3 焊接焊接：welding铆接：riverting熔焊：fusion welding压焊：press welding钎焊：braze welding3.1 焊接理论基础冶金：metallurgy电弧焊：arc welding气焊：acetylene welding电渣焊：electro-slag welding高能束焊：high energy welding电子焊：electronic welding激光焊：laser welding等离子焊：plasma welding电弧：electric arc阳极区：anode region—阴极区：negative polarity弧柱区：arc stream正接法：electrode negative method反接法：opposition method脱氧剂：deoxidizing agent焊缝：welded seam焊缝区：weld zone熔合区：fusion area热影响区：heat-affected zone脆性断裂：brittle fracture过热区：overheated zone正火区：normalized zone相变区：phase change zone焊接应力：welding stress收缩变形：contraction distortion角变形：angular deformation弯曲变形：bend deformation扭曲变形：warping deformation波浪变形：wave transformation反变形法：reversible deformation method刚性固定法：rigid fixing method预热：warming-up—缓冷：slow cool焊后热处理：postweld heat treatment矫形处理：shape-righting3.2 焊接方法埋弧焊：hidden arc welding气体保护焊：gas shielded arc welding氩弧焊：argon welding熔化极氩弧焊：consumable electrode argon welding钨极氩弧焊：argon tungsten-arc welding二氧化碳气体保护焊：CO2 gas shielded arc welding碳弧焊：carbon arc welding碳弧气刨：carbon arc air gouging电渣焊：electro-slag welding高能焊：high grade energy welding等离子弧切割：plasma arc cutting (PAC)堆焊：bead weld电阻焊：resistance welding电焊：electric welding缝焊：seam welding压焊：press welding多点凸焊：multiple projection welding对焊：welding neck—摩擦焊：friction welding扩散焊：diffusion welding硬钎料：brazing alloy软钎料：soft solder3.3 常用金属材料的焊接焊接性：weldability焊接方法：welding method焊接材料：welding material焊条：electrode焊剂：flux material碳素钢：carbon steel低碳钢：low carbon steel中碳钢：medium carbon steel高碳钢：high carbon steel低合金钢：lean alloy steel不锈钢：non-corrosive steel有色金属：nonferrous metal3.4 焊接工艺设计型材：sectional bar药皮：coating焊丝：soldering wire连续焊缝：continuous weld—断续焊缝：intermittent weld应力集中：stress concentration焊接接头：soldered joint坡口：groove对接：abutting joint搭接：lap joint角接：corner joint4 粉末冶金（power metallurgy）粉末冶金成品：finished power metallurgical product铁氧体：ferrite硬质合金：sintered-carbide高熔点金属：high-melting metal陶瓷：ceramic4.1 粉末冶金工艺理论基础压坯：pressed compact扩散：diffusion烧结：agglomeration固溶：solid solubility化合：combination4.2 粉末冶金的工艺流程制备：preparation预处理：anticipation—还原法：reduction method电解法：electrolytic method雾化法：atomization粒度：grain size松装密度：loose density流动性：flowing power压缩性：compressibility筛分：screen separation混合：compounding制粒：pelletization过烧：superburning欠烧：underburnt5 金属复合成型技术自蔓延焊接：SHS welding热等静压：HIP准热等静压：PHIP5.1 液态成型技术与固态成型技术的复合高压铸造：high-pressure casting电磁泵：magnetic-pump压射成型：injection molding柱塞：plunger piston—冲头：drift pin凝固法：freezing method挤压法：extrusion method转向节：knuckle pivot制动器：arresting gear5.2 金属半凝固、半熔融成型技术凝固：freezing半熔融：semi-vitreous触变铸造：thixotropy casting触变锻造：thixotropy forging注射成型：injection molding5.3 其他金属成型新技术快速凝固：flash set非晶态：amorphous溢流法：press over system喷射沉积：ejecting deposit爆炸复合法：explosion cladding method扩散焊接：diffusion welding挤压：extruding轧制：roll down6 非金属材料成型技术—6.1 高分子材料成型技术高分子材料：non-metal material耐腐蚀：resistant material绝缘：insulation老化：ageing耐热性：heat-durability粘弹性：viscoelasticity塑料：plastic material橡胶：rubber合成纤维：synthetic fibre涂料：covering material粘结剂：agglomerant粘度：viscosity热塑性塑料：thermoplastic plastics热固性塑料：thermosetting plastic通用塑料：general-purpose plastics工程塑料：engineering plastic薄膜：thin film增强塑料：reinforced plastics浇注塑料：pouring plastics注射塑料：injiection plastics挤出塑料：extrusion plastics—吹塑塑料：blowing plastics模压塑料：die pressing plastics聚合物：ploymer semiconductor吸湿性：hygroscopic cargo定向作用：directional action生胶：green glue stock填料：carrier丁苯橡胶：SBR顺丁橡胶：BR氯丁橡胶：CR丁腈橡胶：NBR硅橡胶：Q聚氨酯橡胶：U压延：calender硫化：sulfuration胶粘剂：adhesive胶接：glue joint刹车片：brake block零件修复：parts renewal蜂窝夹层：honeycomb core material6.2 工业陶瓷制品的成型技术干燥：drying润滑剂：anti-friction结合剂：binder热压铸：hot injiection moulding 6.3 非金属材料成型技术的新进展热压烧结：hot pressed sintering7 复合材料的成型技术复合材料：composite material树脂：resin7.1 金属复合材料的成型技术硼纤维：boron fiber钛合金：titanium alloy碳纤维：carbon filter等离子喷涂：plasma spraying浸渍法：immersion method锭坯：ingot blank7.2 聚合物基复合材料的成型技术晶须：whisker缠绕成形：enwind forming湿法缠绕：wet method enwind 7.3 陶瓷复合材料成型技术溶胶-凝胶法：sol-gel method化学气相沉积：chemical vapor deposition (CVD) 原位：in situ8 材料成型方法的选择粉末冶金：powder metallurgy工程塑料：engineering plastics工程陶瓷：engineering ceramics。
Material molding and control engineering research through the hot working to change the microstructural structure, macro properties and surface shape, the hot working process of the relevant technological factors on the influence of the materials, solve the molding process development, molding equipment, process optimization theory and method. The die design theory and method, the mould manufacturing of material, heat treatment, processing methods. This subject is the development of national economy of pillar industry.This specialized raise has materials science and engineering theory basis, material molding process and control engineering, mould design and manufacture professional knowledge, can in machinery, mould, material molding manufacture engaged in scientific research, application development, technology and equipment for the design, manufacturing and operation management, the advanced engineering and technical personnel and management personnel. This major is divided into two training module:(1)welding forming and control:Training to adapt to the needs of society, grasp the basic theory of welding forming, metal material welding, welding inspection, welding methods and equipment, welding production management comprehensive knowledge of the senior technical personnel.(2) the mold design and manufacturing:Master the material plastic forming the basic theory, the die design and manufacture, die computer-aided design, materials such as plastic processing production management comprehensive knowledge of the senior technical personnel.The professional bachelor's, master's with PhD degree of engineering and architecture, students can choose to further study. Students can to machinery manufacturing, automotive and shipping manufacture, metal and rubber and plastic materials processing, etc and welding material molding, engaged in the mould design and manufacturing, and related control of the production process, technical development, scientific research, business management, trade marketing, etc. This major wide employment, the market demand, the employment situation is good.Material molding and control engineering is the predecessor of the metal casting professional. The early liberation, China's metal materials professional belongs to the discipline of the machinery, metal forming belong to major in mechanical engineering. Due to the needs of the development of the industry, our country in the early days of the steel smelting level and scale improve soon, corresponding promoted the metal especially steel molding the professional development. Beijing steel institute (now the Beijing science and technology university), wuhan iron and steel institute, shenyang mechanical engineering college is China's earlier a batch of metal forming research institutions. Other universities in the mechanical engineering also have metal casting molding subject, these professional training for our country in the early days of a large number of socialist construction personnel. The-60-s, under the help of the Soviet union, China's rapid development of industry, the corresponding molding the professional have gained great achievements, all kinds of machine manufacturing needs a lot of metal parts, and these parts of the strength and hardness and size requirement enhances unceasingly, metal forming level and therefore get improved a lot.At present, the material molding and control engineering has become one of the components materials to an important process, the modern industrial development on parts of the performance requirements more and more high, some application of materials depends not only on the material itself all sorts of function, but also on its mechanical properties can be processed. Therefore, material molding industry has been accompanied by the development of new high technology ceaselessly. In the 90 s, China has built a large number of modern material molding enterprise, make our country material processing standards have been raised, some export added value of products improve. At present our country some enterprise production of stamping, stretch forming parts already exported to Japan motor corporation the company of affiliation, Toshiba corporation the company of affiliation, Fuji, motor, kawasakiheavy industries, wu mountain instrument corporation and other enterprise. By cold forming, hot extrusion process of copper pipe production has been exported to the United States, Germany and Australia and other countries.Our country material molding and control technology is still needs further development, computer control forming technology in our country at present is still in the initial stage, and in this industry the technology level of our country in the world still is backward, and our country to this domain product demand is big rise, thereby material molding field would be in the next few years for considerable development. 21 century information industry, material industry, the energy industry will be the national production of the three pillar industries, and material molding and control technology material industry is one of the important parts, it would involve all fields of national production.。
压塑和压铸工艺近年，压塑工艺应用于热固性掺混料，如脲醛塑料、酚醛树脂、环氧树脂、蜜胺树脂和橡胶中。
尽管有一些材料可注射成型，但采用压塑工艺仍非常普遍。
压铸用材料较压塑用材料要求可塑性更软。
许多热固性材料具有高抗冲级（1.0ft一lb）和良好缺口冲击强度的保持性，只有在极限压力下才会流动。
压塑热固性材料的压塑成型的明显优点是系统简单。
将材料置入一加热型腔，保压至所要求团化时间。
因工艺过程简单，费用少。
添加剂和增强剂无规则，并能得到较好强度。
由于无浇口和流道，不浪费材料，模具几乎也不用维修。
零件的统一性好，无铸口和流痕，减少了修饰成本。
根据制品结构和所用的塑料应用特点，可采用全压式模具、半压式模具和闭模（可参见有关压塑模具方面的文章）。
设备：简单也是压塑设备的主要特点。
两半压板结合在一起，加温，加压，将材料制成预定形状。
多数压塑过程采用液压操作；也有采用气动操作的。
上下两压板在压力之下在4个角柱上上下移动。
根据压塑设备的大小，压力一般为20—1000吨。
压板的大小一般为8英寸2到5英尺2.在加料和固化以后的脱模方面存在不同自动化程度，常用最现代的液压机进行。
以前的简单系统有温度控制、压力控制、停压控制和时间控制。
现代设备采用更高级的微处理机控制。
对于较薄的制品，在板中可用加热筒或带式加热器。
对较深的制件，需要用筒形电加热器、蒸汽加热或热油系统加热。
有数种用于压塑中的加热体系：用蒸汽加热模温均匀，但加热温度限在350°F以下；套筒加热或其它加热（加热盘管、加热带等）比较干净，易于保养，用得比较普及；热油加热，由于加热介质循环稳定，所以加热均匀。
现在又有许多新加热方法，热水加热，类似于热油加热，加热介质一水一气体燃烧连续循环，可提供更高的压塑温度。
增强改性高分子材料工业发展迅速，要求压塑工业有新改进。
模塑增强塑料用两个模具：阳模（模塞）和阴模（模腔）。
当模具充满增强材料时，对模的两半热模具闭合，然后加热、加压固化得到产品。
材料英语证书考试(PEC)金属材料成型词汇部门： xxx时间： xxx整理范文，仅供参考，可下载自行编辑材料英语证书考试(PEC>-金属材料成型词汇plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸>draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号>shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板<顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模>feature die公母模female die母模(凹模>upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板> stripping plate内外打(脱料板> outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件>deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块塑件&模具相关英文compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具移转成型用模具encapsulation molding低压封装成型射出成型用模具two plate两极式<模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道h=0.02~0.05mmw=3.2mmL=3~5mmwelding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar><成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆> slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口H=F=1/2t~1/5tT=2.5~3.5mmdiaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Φ0.8~1.0mmRunner less无浇道(sprue less>无射料管方式long nozzle延长喷嘴方式sprue浇口。
材料成型及控制工程专业英语翻译（部分）第一篇：材料成型及控制工程专业英语翻译(部分)第3章的原则塑料成型3。
1热加工物理冶金现在公认的热加工物理冶金的原则。
在变形过程本身，例如一个滚动的传递，加工硬化发生，但回收和再结晶过程的动态软化平衡。
这些过程，这是热激活，导致一个流动应力，应变率和温度，以及依赖于应变。
结构性变化的应变与位错密度增加放置在一个临界应变（εc）奥氏体钢，镍和铜合金材料的结果，直到达到储存的能量足够高时会导致动态再结晶。
随着进一步的压力，动态再结晶发生多次新的再结晶晶粒本身加工硬化储存能量的临界水平。
这些动态的结构变化离开金属处于不稳定的状态，并提供静态恢复和静态再结晶变形传递后的推动力。
可遵循静态再结晶晶粒的生长，如果温度足够高。
为了能够把这些原则运用到商业工作流程，我们需要回答两个主要问题：（一）多久再结晶后变形传递到位;及（b）什么晶粒尺寸再结晶和晶粒生长产生？这些问题的答案决定进入未来和后续传递物质的结构，从而影响材料的流动应力和所需的工作力量。
最后，他们确定的热作产品的结构和性质。
3。
1。
1动态的结构变化在变形奥氏体在热加工温度和恒应变速率，观察应力应变曲线的特点形式如图所示。
3。
1。
这些曲线是低合金钢，扭转测试，但类似的其它钢得到扭转，紧张，或压缩测试奥氏体条件。
经过初期快速加工硬化曲线通过动态再结晶的发生相关的一个最大。
在流动应力峰值出现一些低分数的再结晶后已经发生这样的峰值应变（εp）总是大于临界应变动态recystallization（εc）。
两个菌株之间的关系是复杂的，但它已建议thatεc=αεp（其中α是一个常数）是一个合理的近似变形热工权益的条件下。
然而，α的建议值不同，0.83，0.86，和0.67。
它从图3.1可以看出，εp增加系统与ZenerMn钢，但较低的值的270和286 kJ / mol的范围，也被观察到。
Asεc标志着亚颗粒有点不发达，加工硬化和动态恢复行动，其中也包含了再结晶核的变化，在微观结构，它也是一个静态后发生的结构性变化的临界应变变形。
模具技术用语各种模具常用成形方式accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形shell casting 壳模铸造foam forming 发泡成形sinter forging 烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模landed plunger mold 有肩柱塞式模具burnishing die 挤光模landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具extrusion die 挤出模palletizing die 迭层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 轭型模模具厂常用之标准零配件air vent vale 通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流檔板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 扥架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁) cavity retainer plate 模穴扥板center pin 中心梢clamping block 锁定块coil spring 螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底die block 块形模体die body 铸模座die bush 合模衬套die button 冲模母模die clamper 夹模器die fastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 冲模板die set 冲压模座direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowel hole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drive bearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘销flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib 凹形拉紧销goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶镦冲头headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar 脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶销lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢locating ring 定位环lock block 压块locking block 定位块locking plate 定位板loose bush 活动衬套making die 打印冲子manifold block 歧管档块master plate 靠模样板match plate 分型板mold base 塑料模座mold clamp 铸模紧固夹mold platen 模用板moving bolster 换模保持装置moving bolster plate 可动侧模板one piece casting 整体铸件parallel block 平行垫块paring line 分模线parting lock set 合模定位器pass guide 穴型导板peened head punch 镶入式冲头pilot pin 导销pin gate 针尖浇口plate 衬板pre extrusion punch 顶挤冲头punch 冲头puncher 推杆pusher pin 衬套梢rack 机架rapping rod 起模杆re-entrant mold 凹入模retainer pin 嵌件梢retainer plate 扥料板return pin 回位梢riding stripper 浮动脱模器ring gate 环型浇口roller 滚筒runner 流道runner ejector set 流道顶出器runner lock pin 流道拉梢screw plug 头塞set screw 固定螺丝shedder 脱模装置shim 分隔片shoe 模座之上下模板shoot 流道shoulder bolt 肩部螺丝skeleton 骨架slag riser 冒渣口slide(slide core) 滑块slip joint 滑配接头spacer block 间隔块spacer ring 间隔环spider 模蕊支架spindle 主轴sprue 注道sprue bushing 注道衬套sprue bushing guide 注道导套sprue lock bushing 注道定位衬套sprue puller 注道拉料销spue line 合模线square key 方键square nut 方螺帽square thread 方螺纹stop collar 限位套stop pin 止动梢stop ring 止动环stopper 定位停止梢straight pin 圆柱销stripper bolt 脱料螺栓stripper bushing 脱模衬套stripper plate 剥料板stroke end block 行程止梢submarine gate 潜入式浇口support pillar 支撑支柱/顶出支柱support pin 支撑梢supporting plate 扥板sweep templete 造模刮板tab gate 辅助浇口taper key 推拔键taper pin 拔锥梢/锥形梢teeming 浇注three start screw 三条螺纹thrust pin 推力销tie bar 拉杵tunnel gate 隧道形浇口vent 通气孔wortle plate 拉丝模板模具常用之工作机械3D coordinate measurement 三次元量床boring machine 搪孔机cnc milling machine CNC铣床contouring machine 轮廓锯床copy grinding machine 仿形磨床copy lathe 仿形车床copy milling machine 仿形铣床copy shaping machine 仿形刨床cylindrical grinding machine 外圆磨床die spotting machine 合模机drilling machine 钻孔机engraving machine 雕刻机engraving E.D.M. 雕模放置加工机form grinding machine 成形磨床graphite machine 石墨加工机horizontal boring machine 卧式搪孔机horizontal machine center 卧式加工制造中心internal cylindrical machine 内圆磨床jig boring machine 冶具搪孔机jig grinding machine 冶具磨床lap machine 研磨机machine center 加工制造中心multi model miller 靠磨铣床NC drilling machine NC钻床NC grinding machine NC磨床NC lathe NC车床NC programming system NC程序制作系统planer 龙门刨床profile grinding machine 投影磨床projection grinder 投影磨床radial drilling machine 旋臂钻床shaper 牛头刨床surface grinder 平面磨床try machine 试模机turret lathe 转塔车床universal tool grinding machine 万能工具磨床vertical machine center 立式加工制造中心wire E.D.M. 线割放电加工机检验量测工具用语autocollimator 自动准直机bench comparator 比长仪block gauge 块规bore check 精密小测定器calibration 校准caliper gauge 卡规check gauge 校对规clearance gauge 间隙规clinoretee 测斜仪comparator 比测仪cylinder square 圆筒直尺depth gauge 测深规dial indicator 针盘指示表dial snap gauge 卡规digital micrometer 数位式测微计feeler gauge 测隙规gauge plate 量规定位板height gauge 测高规inside calipers 内卡钳inside micrometer 内分厘卡interferometer 干涉仪leveling block 平台limit gauge 限规micrometer 测微计mil 千分之一吋monometer 压力计morse taper gauge 莫氏锥度量规nonius 游标卡尺optical flat 光学平晶optical parallel 光学平行passimeter 内径仪position scale 位置刻度profile projector 轮廓光学投影仪protractor 分角器radius 半径ring gauge 环规sine bar 正弦量规snap gauge 卡模square master 直角尺stylus 触针telescopic gauge 伸缩性量规working gauge 工作量规模具钢材alloy tool steel 合金工具钢aluminium alloy 铝合金钢bearing alloy 轴承合金blister steel 浸碳钢bonderized steel sheet 邦德防蚀钢板carbon tool steel 碳素工具钢clad sheet 被覆板clod work die steel 冷锻模用钢emery 金钢砂ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢galvanized steel sheet 镀锌铁板hard alloy steel 超硬合金钢high speed tool steel 高速度工具钢hot work die steel 热锻模用钢low alloy tool steel 特殊工具钢low manganese casting steel 低锰铸钢marging steel 马式体高强度热处理钢martrix alloy 马特里斯合金meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁merchant iron 市售钢材molybdenum high speed steel 钼系高速钢molybdenum steel 钼钢nickel chromium steel 镍铬钢prehardened steel 顶硬钢silicon steel sheet 硅钢板stainless steel 不锈钢tin plated steel sheet 镀锡铁板tough pitch copper 韧铜troostite 吐粒散铁tungsten steel 钨钢vinyl tapped steel sheet 塑料覆面钢板表面处理关连用语age hardening 时效硬化ageing 老化处理air hardening 气体硬化air patenting 空气韧化annealing 退火anode effect 阳极效应anodizing 阳极氧化处理atomloy treatment 阿扥木洛伊表面austempering 奥氏体等温淬火austenite 奥斯田体/奥氏体bainite 贝氏体banded structure 条纹状组织barrel plating 滚镀barrel tumbling 滚筒打光blackening 染黑法blue shortness 青熟脆性bonderizing 磷酸盐皮膜处理box annealing 箱型退火box carburizing 封箱渗碳bright electroplating 辉面电镀bright heat treatment 光辉热处理bypass heat treatment 旁路热处理carbide 炭化物carburized case depth 浸碳硬化深层carburizing 渗碳cementite 炭化铁chemical plating 化学电镀chemical vapor deposition 化学蒸镀coarsening 结晶粒粗大化coating 涂布被覆cold shortness 低温脆性comemtite 渗碳体controlled atmosphere 大气热处理corner effect 锐角效应creeping discharge 蠕缓放电decarburization 脱碳处理decarburizing 脱碳退火depth of hardening 硬化深层diffusion 扩散diffusion annealing 扩散退火electrolytic hardening 电解淬火embossing 压花etching 表面蚀刻ferrite 肥粒铁first stage annealing 第一段退火flame hardening 火焰硬化flame treatment 火焰处理full annealing 完全退火gaseous cyaniding 气体氧化法globular cementite 球状炭化铁grain size 结晶粒度granolite treatment 磷酸溶液热处理graphitizing 石墨退火hardenability 硬化性hardenability curve 硬化性曲线hardening 硬化heat treatment 热处理hot bath quenching 热浴淬火hot dipping 热浸镀induction hardening 高周波硬化ion carbonitriding 离子渗碳氮化ion carburizing 离子渗碳处理ion plating 离子电镀isothermal annealing 等温退火liquid honing 液体喷砂法low temperature annealing 低温退火malleablizing 可锻化退火martempering 麻回火处理martensite 马氏体/硬化铁炭metallikon 金属喷镀法metallizing 真空涂膜nitriding 氮化处理nitrocarburizing 软氮化normalizing 正常化oil quenching 油淬化overageing 过老化overheating 过热pearlite 针尖组织phosphating 磷酸盐皮膜处理physical vapor deposition 物理蒸镀plasma nitriding 离子氮化pre-annealing 预备退火precipitation 析出precipitation hardening 析出硬化press quenching 加压硬化process annealing 制程退火quench ageing 淬火老化quench hardening 淬火quenching crack 淬火裂痕quenching distortion 淬火变形quenching stress 淬火应力reconditioning 再调质recrystallization 再结晶red shortness 红热脆性residual stress 残留应力retained austenite 残留奥rust prevention 防蚀salt bath quenching 盐浴淬火sand blast 喷砂处理seasoning 时效处理second stage annealing 第二段退火secular distortion 经年变形segregation 偏析selective hardening 部分淬火shot blast 喷丸处理shot peening 珠击法single stage nitriding 等温渗氮sintering 烧结处理soaking 均热处理softening 软化退火solution treatment 固溶化热处理spheroidizing 球状化退火stabilizing treatment 安定化处理straightening annealing 矫直退火strain ageing 应变老化stress relieving annealing 应力消除退火subzero treatment 生冷处理supercooling 过冷surface hardening 表面硬化处理temper brittleness 回火脆性temper colour 回火颜色tempering 回火tempering crack 回火裂痕texture 咬花thermal refining 调质处理thermoechanical treatment 加工热处理time quenching 时间淬火transformation 变态tufftride process 软氮化处理under annealing 不完全退火vacuum carbonitriding 真空渗碳氮化vacuum carburizing 真空渗碳处理vacuum hardening 真空淬火vacuum heat treatment 真空热处理vacuum nitriding 真空氮化water quenching 水淬火wetout 浸润处理焊接用语acetylene 乙炔ampere 电流安培angle welding 角焊arc 电弧argon arc welding 氩弧焊接bare electrode 光熔接条butt welding 对接焊接camber 电弧弯曲cascade 阶迭熔接法clad weld 被覆熔接crator 焊疤excess metal 多余金属filler rod 焊条fillet weld 填角焊接gas shield 气体遮蔽groove welding 起槽熔接hand face shield 手握面罩hard facing 硬表面堆焊jig welding 工模焊接laser beam welding 雷射光焊接metal electrode insert gas welding MIG熔接nugget 点焊熔核overlaying 堆焊peening of welding 珠击熔接法plug welding 塞孔熔接positioned welding 正向熔接pressure welding 压焊propane gas cutting 丙烷气切割pure nickel electrode 纯镍熔接条reinforcement of weld 加强焊接resist 抗蚀护膜root running 背面熔接seam 焊缝seaming 接合seam welding 流缝熔接series seam welding 串联缝熔接skip welding process 跳焊法spark 火花spot welding 点焊接stitch welding 针角焊接stud arc welding 电弧焊接under laying 下部焊层void 焊接空隙weld flow mark 焊接流痕weld flush 焊缝凸起weld line 焊接纹weld mark 焊接痕weld penetration 熔接透入weld zone 焊接区welding 焊接welding bead 焊接泡welding direction 焊接方向welding distortion 焊接变形welding flux 焊剂welding ground 电熔接地welding interval 焊接周期welding stress 熔接应变welding torch 熔接气炬射出成形关联用语activator 活化剂bag moulding 气胎施压成形bonding strength 黏合强度breathing 排气caulking compound 填隙料cell 气孔cold slug 半凝式射出colorant 着色剂color matching 调色color masterbatch 色母料compound 混合料copolymer 共聚合体cull 残料废品cure 凝固化cryptometer 不透明度仪daylight 开隙dry cycle time 空料试车周期时间ductility 延性elastomer 弹性体extruded bead sealing 压出粒涂层法feed 供料filler 充填剂film blowing 薄膜吹制法floating platen 活动模板foaming agent 发泡剂gloss 光泽granule 颗粒料gunk 料斗hot mark 热斑hot stamping 烫印injection nozzle 射出喷嘴injection plunger 射出柱塞injection ram 射出冲柱isomer 同分异构物kneader 混合机leveling agent 匀涂剂lubricant 润滑剂matched die method 配合成形法mould clamping force 锁模力mould release agent 脱模剂nozzle 喷嘴oriented film 取向薄膜parison 吹气成形坏料pellet 粒料plasticizer 可塑剂plunger 压料柱塞porosity 孔隙率post cure 后固化premix 预混料purging 清除reciprocating screw 往复螺杆resilience 回弹性resin injection 树脂射出法rheology 流变学sheet 塑料片shot 注射shot cycle 射出循环slip agent 光滑剂take out device 取料装置tie bar 拉杆toggle type mould clamping system 肘杆式锁模装置torpedo spreader 鱼雷形分流板transparency 透明性void content 空洞率塑料原料acrylic 压克力casein 酪素cellulose acetate 醋酸纤维素CA cellulose acetate butyrate 醋酸丁酸纤维素CAB composite material 复合材料cresol resin 甲酚树脂CFdially phthalate 苯二甲酸二烯丙酯disperse reinforcement 分散性强化复合材料engineering plastics 工程塑料epoxy resin 环氧树脂EPethyl cellulose 乙基纤维素ethylene vinylacetate copolymer 乙烯-醋酸乙烯EV A ethylene-vinlacetate copolyme 醋酸乙烯共聚物EV A expanded polystyrene 发泡聚苯乙烯EPS fiber reinforcement 纤维强化热固性/纤维强化复合材料high density polyethylene 高密度聚乙烯HDPEhigh impact polystyrene 高冲击聚苯乙烯HIPShigh impact polystyrene rigidity 高冲击性聚苯乙烯low density polyethylene 低密度聚乙烯LDPE melamine resin 三聚氰胺酚醛树脂MF nitrocellulose 硝酸纤维素phenolic resin 酚醛树脂plastic 塑料polyacrylic acid 聚丙烯酸PAPpolyamide 耐龙PA polybutyleneterephthalate 聚对苯二甲酸丁酯PBT polycarbonate 聚碳酸酯PC polyethyleneglycol 聚乙二醇PFG polyethyleneoxide 聚氧化乙烯PEO polyethyleneterephthalate 聚乙醇对苯PETP polymetylmethacrylate 聚甲基丙烯酸甲酯PMMA polyoxymethylene 聚缩醛POM polyphenylene oxide 聚硫化亚苯polyphenyleneoxide 聚苯醚PPO polypropylene 聚丙烯PP polystyrene 聚苯乙烯PS polytetrafluoroethylene 聚四氟乙烯PTFE polytetrafluoroethylene 聚四氟乙烯polythene 聚乙烯PE polyurethane 聚氨基甲酸酯PU polyvinylacetate 聚醋酸乙烯PV AC polyvinylalcohol 聚乙烯醇PV A polyvinylbutyral 聚乙烯醇缩丁醛PVB polyvinylchloride 聚氯乙烯PVC polyvinylfuoride 聚氟乙烯PVF polyvinylidenechloride 聚偏二氯乙烯PVDC prepolymer 预聚物silicone resin 硅树脂thermoplastic 热塑性thermosetting 热固性thermosetting plastic 塑料unsaturated polyester 不饱和聚酯树脂成形不良用语aberration 色差atomization 霚化bank mark 滞料纹bite 咬入blacking hole 涂料孔(铸疵) blacking scab 涂料疤blister 起泡blooming 起霜blow hole 破孔blushing 泛白body wrinkle 侧壁皱纹breaking-in 冒口带肉bubble 膜泡burn mark 糊斑burr 毛边camber 翘曲cell 气泡center buckle 表面中部波皱check 细裂痕checking 龟裂chipping 修整表面缺陷clamp-off 铸件凹痕collapse 塌陷color mottle 色斑corrosion 腐蚀crack 裂痕crazing 碎裂crazing 龟裂deformation 变形edge 切边碎片edge crack 裂边fading 退色filler speak 填充料斑fissure 裂纹flange wrinkle 凸缘起皱flaw 刮伤flow mark 流痕galling 毛边glazing 光滑gloss 光泽grease pits 污斑grinding defect 磨痕haircrack 发裂haze 雾度incrustation 水锈indentation 压痕internal porosity 内部气孔mismatch 偏模mottle 斑点necking 缩颈nick 割痕orange peel 橘皮状表面缺陷overflow 溢流peeling 剥离pit 坑pitting corrosion 点状腐蚀plate mark 模板印痕pock 麻点pock mark 痘斑resin streak 树脂流纹resin wear 树脂脱落riding 凹陷sagging 松垂saponification 皂化scar 疤痕scrap 废料scrap jam 废料阻塞scratch 刮伤/划痕scuffing 深冲表面划伤seam 裂痕shock line 模口挤痕short shot 充填不足shrinkage pool 凹孔sink mark 凹痕skin inclusion 表皮折迭straightening 矫直streak 条状痕surface check 表面裂痕surface roughening 橘皮状表皮皱折surging 波动sweat out 冒汗torsion 扭曲warpage 翘曲waviness 波痕webbing 熔塌weld mark 焊痕whitening 白化wrinkle 皱纹模具常用刀具与工作法用语adjustable spanner 活动扳手angle cutter 角铣刀anvil 铁钻arbour 心轴backing 衬垫belt sander 带式打磨机buffing 抛光chamfering machine 倒角机chamfering tool 去角刀具chisel 扁錾chuck 夹具compass 两角规concave cutter 凹面铣刀convex cutter 凸形铣刀cross joint 十字接头cutting edge clearance 刃口余隙角drill stand 钻台edge file 刃用锉刀file 锉刀flange joint 凸缘接头grinder 砂轮机hammer 铁锤hand brace 手摇钻hatching 剖面线hexagon headed bolt 六角头螺栓hexagon nut 六角螺帽index head 分度头jack 千斤顶jig 治具kit 工具箱lapping 研磨metal saw 金工锯nose angle 刀角pinchers 钳子pliers 铗钳plug 柱塞头polisher 磨光器protable driller 手提钻孔机punch 冲头sand paper 砂纸scraper 刮刀screw driver 螺丝起子scribing 划线second out file 中纹锉spanner 扳手spline broach 方栓槽拉刀square 直角尺square sleeker 方形镘刀square trowel 直角度stripping 剥离工具T-slot T形槽tool for lathe 车刀tool point angle 刀刃角tool post 刀架tosecan 划线盘trimming 去毛边waffle die flattening 压纹效平wiper 脱模钳wrench 螺旋扳手计算机关联用语3D modeling 三次元模拟access 通路animation 卡通影片application 应用board 基板bug 故障bus 总线CAD 计算机辅助设计CAE 计算机辅助工程分析CAM 计算机辅助制造cassette 卡座color display 彩色显示器command 指令communication 通信compact 精简小型computer 计算机copy 复制cursor 游标curve modeling 曲面仿真database 数据库design 设计digitizing 数字化disk 磁盘dot 点eyelet 眼孔floppy 磁盘片format 格式化graphic 圆解hardware 硬件honeycomb 蜂巢interface 界面know how 秘诀laser printer 激光打印机lay out 布置memory 记忆memory swap 交换记忆microprocessor 微处理器modeling 造型module 模块monitor 屏幕mouse 鼠标need 需求network 网络new version 新版on line 上线中option 选择PC 个人计算机plotter 绘图机program 程序scanning 扫描simulation 仿真software 软件solid model 实体模型system 系统tape 磁带terminal 终端机texture 构造trim 修边venter 排气风扇word processor 文书处理器各种冲模加工关连用语barreling 滚光加工belling 压凸加工bending 弯曲加工blanking 下料加工bulging 撑压加工burring 冲缘加工cam die bending 凸轮弯曲加工caulking 铆合加工coining 压印加工compressing 压缩加工compression bending 押弯曲加工crowning 凸面加工curl bending 卷边弯曲加工curling 卷曲加工cutting 切削加工dinking 切断蕊骨double shearing 迭板裁断drawing 引伸加工drawing with ironing 抽引光滑加工embossing 浮花压制加工extrusion 挤制加工filing 锉削加工fine blanking 精密下料加工finish blanking 光制下料加工finishing 精整加工flanging 凸缘加工folding 折边弯曲加工folding 折迭加工forming 成形加工impact extrusion 冲击挤压加工indenting 压痕加工ironing 引缩加工knurling 滚花lock seaming 固定接合louvering 百叶窗板加工marking 刻印加工necking 颈缩加工notching 冲口加工parting 分断加工piercing 冲孔加工progressive bending 连续弯曲加工progressive blanking 连续下料加工progressive drawing 连续引伸加工progressive forming 连续成形加工reaming 铰孔加工restriking 二次精冲加工riveting 铆接加工roll bending 滚筒弯曲加工roll finishing 滚压加工rolling 压延加工roughing 粗加工scrapless machining 无废料加工seaming 折弯重迭加工shaving 缺口修整加工shearing 切断加工sizing 精压加工/矫正加工slitting 割缝加工spinning 卷边铆接staking 铆固stamping 锻压加工swaging 挤锻压加工trimming 整缘加工upsetting 锻粗加工wiring 抽线加工冲压机械及周边关连用语back shaft 支撑轴blank determination 胚料展开bottom slide press 下传动式压力机board drop hammer 板落锤brake 煞车buckle 剥砂面camlachie cramp 铸包casting on flat 铆合chamotte sand 烧磨砂charging hopper 加料漏斗clearance 间隙closed-die forging 合模锻造clump 夹紧clutch 离合器clutch brake 离合器制动器clutch boss 离合器轮壳clutch lining 离合器覆盖coil car 带卷升降运输机coil cradle 卷材进料装置coil reel stand 钢材卷料架column 圆柱connection screw 连杆调节螺钉core compound 砂心黏结剂counter blow hammer 对击锻锤cradle 送料架crank 曲柄轴crankless 无曲柄式cross crank 横向曲轴cushion 缓冲depression 外缩凹孔dial feed 分度送料die approach 模口角度die assembly 合模die cushion 模具缓冲垫die height 冲压闭合高度die life 模具寿命die opening 母模逃孔die spotting press 调整冲模用压力机double crank press 双曲柄轴冲床draght angle 逃料倾斜角edging 边锻伸embedded core 加装砂心feed length 送料长度feed level 送料高度filling core 埋入砂心filling in 填砂film play 液面花纹fine blanking press 精密下料冲床forging roll 辊锻机finishing slag 炼后熔渣fly wheel 飞轮fly wheel brake 飞轮制动器foot press 脚踏冲床formboard 进模口板frame 床身机架friction 摩擦friction brake 摩擦煞车gap shear 凹口剪床gear 齿轮gib 滑块引导部gripper 夹具gripper feed 夹持进料gripper feeder 夹紧传送装置hammer 槌机hand press 手动冲床hand rack pinion press 手动齿轮齿条式冲床hand screw press 手动螺旋式冲床hopper feed 料斗送料idle stage 空站inching 微调尺寸isothermal forging 恒温锻造key clutch 键槽离合器knockout 脱模装置knuckle mechanic 转向机构land 模具直线刀面部level 水平loader 供料器unloader 卸料机loop controller 闭回路控制器lower die 下模micro inching device 微寸动装置microinching equipment 微动装置motor 马达moving bolster 活动工作台notching press 冲缺口压力机opening 排料逃孔overload protection device 防超载装置pinch roll 导正滚轮pinion 小齿轮pitch 节距pressfit 压入progressive 连续送料pusher feed 推杆式送料pusher feeder 料片押片装置quick die change system 快速换模系统regrinding 再次研磨releasing 松释动作reversed blanking 反转下料robot 机器人roll forming machine 辊轧成形roll forming machine 辊轧成形机roll release 脱辊roller feed 辊式送料roller leveler 辊式矫直机rotary bender 卷弯成形机safety guard 安全保护装置scrap cutter 废料切刀scrap press 废料冲床seamless forging 无缝锻造separate 分离shave 崩砂shear angle 剪角sheet loader 薄板装料机shot 单行程工作shrinkage fit 收缩配合shut height 闭合高度sieve mesh 筛孔sintering of sand 铸砂烧贴slide balancer 滑动平衡器slug hole 逃料孔spin forming machine 旋压成形机spotting 合模stack feeder 堆栈拨送料机stickness 黏模性straight side frame 冲床侧板stretcher leveler 拉伸矫直机strip feeder 料材送料装置stripping pressure 弹出压力stroke 冲程take out device 取料装置toggle press 肘杆式压力机transfer 传送transfer feed 连续自动送料装置turrent punch press 转塔冲床two speed clutch 双速离合器uncoiler 闭卷送料机unloader 卸载机vibration feeder 振动送料机wiring press 嵌线卷边机线切割放电加工关连用语abnormal glow 不规则辉光放电arc discharge 电弧放电belt 皮带centreless 无心chrome bronze 铭铜clearance angle 后角corner shear drop 直角压陷deflection 桡曲度discharge energy 放电能量dressing 修整dwell 保压flange 凸缘gap 间隙graphite 石墨graphite contraction allowance 电极缩小余量graphite holder 电极夹座hair crack 发裂horn 电极臂jump 跳刀magnetic base 磁性座master graphite 标准电极pipe graphite 管状电极pulse 脉冲rib working 肋部加工roller electrode 滚轮式电极rotary surface 旋转面shank 柄部sharp edge 锐角部tough bronze 韧铜traverse 摇臂tungsten bronze 钨青铜waviness 波形起伏work 工件working allowance 加工余量working dischard 加工废料锻铸造关连用语accretion 炉瘤acid converter 酸性转炉acid lining cupola 酸性熔铁炉acid open-hearth furnace 酸性平炉aerator 松砂机air set mold 常温自硬铸模airless blasting cleaning 离心喷光all core molding 集合式铸模all round die holder 通用模座assembly mark 铸造合模记号back pouring 补浇注backing sand 背砂base bullion 粗金属锭base permeability 原砂透气度belling 压凸billet 坏料bleed 漏铸blocker 预锻模膛blocking 粗胚锻件blow hole 铸件气孔board drop hammer 板落锤bottom pour mold 底浇bottom pouring 底注boxless mold 脱箱砂模break-off core 缩颈砂心brick molding 砌箱造模法buckle 剥砂面camber 错箱camlachie cramp 铸包cast blade 铸造叶片casting flange 铸造凸缘casting on flat 水平铸造chamotte sand 烧磨砂charging hopper 加料漏斗cleaning of casting 铸件清理closed-die forging 合模锻造core compound 砂心黏结剂core template 砂心模板core vent 砂蕊排气孔corner gate 压边浇口counter blow hammer 对击锻造counter lock 止口镶嵌方式depression 外缩凹孔die approach 模口角度draw out 锻造拔长draw plate 起模板draw spike 起模长针dummying 预锻embedded core 加装砂心erosion 冲砂fettling 铸件清理filling core 埋入砂心filling in 填砂film play 液面花纹finishing slag 炼后熔渣flash gutter 锻模飞边槽flask molding 砂箱造模forging roll 辊锻机formboard 进模口板gutter 锻模飞边槽hammer man 锻工heading machine 顶镦机impacter 卧式锻造机inblock cast 整体铸造ingot 铸锭ingot blank 铸坯inlay casting 镶铸法investment casting 失模铸造isothermal forging 恒温锻造loose piece 木模活块molding pit 铸模地坑pouring process 浇注法recasting 重铸roll forging 轧锻rolled surface 轧制表面rough sand 粗砂roughing forge 粗锻sand crushing 塌箱seamless forging 无缝锻造separate 分离shave 崩砂shrinkage fit 收缩配合shut height 闭合高度sieve mesh 筛孔sintering of sand 铸砂烧贴slag 熔渣slag inclusion 夹渣stickness 黏模性strip layout 带状胚料排样法tap casting 顶注top gate 顶注浇口unworked casting 不加工铸件upender 翻转装置upending 顶锻uphill casting 底铸white cast iron 白口铸件模具加工方法barrel 滚筒(加工) bending 波纹加工broaching 拉刀切削centering 定中心cutting 切削cylindrical lathe cutting 外圆车削electric discharge machine 放电加工electrolytic grinding 电解研磨embossing 压花加工facing 面车削filing 锉刀修润hand finishing 手工修润hemming 卷边加工hobbing 滚齿加工joggling 摇动加工lapping 抛光/研磨修润laser beam machining 雷射加工lathe cutting 车床车削planning 刨削加工polishing 抛亮光reaming 铰孔修润rough machining 粗切削rounding 圆形加工sawing 锯削scaling 清除钢碇缺陷shaping 成形加工skiving 表面研磨slotting 切缝切削taper turning 锥度车削thread cutting 螺纹切削ultrasonic machining 超音波加工up cut milling 逆铣加工学理实验与试验用语air permeability test 透气性试验austenitic steel 沃斯田铁钢brinell hardness 布耐内尔硬度brinell hardness test 布氏硬度试验charpy impact test 夏比冲击试验conical cup test 圆锥杯突试验cup flow test 杯模式流动度试验dart drop impact test 落锤冲击试验Elmendorf test 埃罗门多撕裂强度试验environmental stress cracking test 环境应力龟裂试验ericessen test 埃留伸薄板拉伸试验falling ball impact test 落球冲击试验fatigue test 疲劳试验ferrite 纯铁体gantt chart 甘特图heat cycle test 热循环试验histogram 柱状图hot bend test 热弯试验izod impact test 埃左德冲击试验loop tenacity 环结强度martens heat distortion temperature test 马顿斯耐热试验martensite 马氏体mullen bursting strength tester 密廉式破裂强度试验机nol ring test 诺尔环试验normal distribution 常态分配ozone resistance test 抗臭氧试验pareto diagram 柏拉图peeling test 剥离试验pinhole test 针孔试验机rattler test 磨耗试验rockweel hardness test 洛氏硬度试验rockweel hardness 洛氏威尔硬度rolinx process 罗林克斯射出压缩成形法rossi-peakes flow test 罗西皮克斯流动试验sampling inspection 抽样检查scratch hardness 抗刮硬度shore hardness 萧氏硬度spiral flow test 螺旋流动试验surface abrasion test 表面磨耗试验taber abraser 泰伯磨耗试验机tensile impact test 拉伸冲击试验tensile strength 抗拉强度tension test 张力试验thermal shock test 冷热剧变试验torsion test 扭曲试验ubbelohde viscometer 乌别洛德黏度计vicat indentation test 维卡针压陷试验Vickers hardness test 维氏硬度试验warpage test 翘曲试验weatherometer 人工老化试验机weissenberg effect 威森伯格回转效应砂轮用语abrasive 砂轮Al2O3 氧化铝balance 平衡bond 结合borazon 氧化硼立方晶buffing wheel 抛光布轮diamond 钻石dresser 砂轮整修机dressing 修整endless grinding belt 循环式研磨带finishing allowance 加工余量grain 磨粒grinding disc 研磨盘jamp up 孔眼堵塞mesh 网筛目parameter 参数resinoid grinding wheel 半树脂型砂轮slitting 切缝量vitrified 陶瓷的wheel 旋转机械设计及周边其它用语assembly drawing 装配图auto tool change cycle 自动换刀时间周期beam 横梁bending moment 弯矩bending stress 弯曲应力bottoming 底靠buckling 纵弯曲chamfering 去角斜切channel 凹槽chattering 颤动check point 查核点chip 切屑chip conveyor 排屑输送机coefficient of friction 摩擦系数compact 小型的cooling pipe 冷却管coupon 试样胚deflection 挠曲量distortion 扭曲变形draft taper 拔模锥度draw out 拉拔fit tolerance 配合公差flexible rigidity 弯曲刚性gas vent 气孔hatching 剖面线heater cooler 加热器冷却装置hook cavity 钩穴inching 寸动lug 凸缘maintenance 维修保固metallurgy 冶金学notch effect 切口效果out of roughness 真圆度performance 动作性能pit 坑plane strain 倒角应力plug mill 蕊棒轧管机repeated load 重复载荷riveted joint 铆钉接合sand paper 砂纸shift 偏移shrink fit 热压配合shrinkage hole 缩孔sinking 凹陷sketch 草图spalling 剥落straightness 直度submarine 深陷式surface roughness 表面粗度tapping 攻螺丝thermocouple 热电耦torsion load 扭转载荷toughness 韧性tracing 描图under cut 凹割业务与贸易关连用语accept order 接受订货account 账户after service 售后服务amendment 修正annual sales 年销售额at sight 见票即付balance 余额bank draft 汇票bargain goods 廉价品batch 批次bid 出价bid sales 投标买卖bill of landing 提单bills receivable 应收票据brand 品牌bulk cargo 散装货business transaction 商业交易buyer 买方carbon copy 打字副本cargo collection 揽货carton 纸箱cash in advance 预付现金catalogue 型录cheque 支票CLF 运费保险费在内价格claim 索赔clearance goods 清仓品commision 佣金commission 批发商complain 抱怨container 货柜correspondence bank 往来银行cost 成本cost and freight; C&F 含运费价格custom broker 报关行customer 客户D/A 承兑交单D/P 付款交单deferred payment 分期付款deferred shipment 分期装运delivery on spot 当场交货delivery time 交期delivery order 交货单discount 折扣discount on draft 贴现documentary draft 跟单汇票down payment 订金enclosure 附件endorsement 背书enquete 调查exhibition 展览会export 出口factory visiy 工厂参观favourable price 合宜价格foreign exchange 外汇free on board 船上交货价idea price 希望价格import 进口Japanese Industrial 日本工业规格invoice 发票L/C 信用状margin 利润market 市价net weight 净重no payment 拒绝付款odd item 零头offer 报价open account 交互计算order 订单over looked 疏漏packing 包装pamphlet 小册子partial shipment 分批装船patent 专利paying price 合算价格payment method 付款方式port of destination 目地港port of trans-shipment 转口港price 价格price decending 减价price rising 涨价procurement 采办prompt delivery 实时交货purchase 购入purchasing agent 采购代理商quotation 报价单rebate 回扣reference 查询remittance 汇款repeat order 追加订货request letter 请求函rumor 风评second hand goods 二手货shipper 货主shipping 装船shipping mark 麦头shipment 出货sold out 卖完sole agent 总代理商special discount 特别折扣specification 规格sample order 指样订货standing 信用情形storage charge 仓租subcontract 外包subject to final confirmation 有待确认之报价supplier 供货商T/T 电汇tie-in sale 搭售trade fair 商展会trans-shipment 转运transferred 已转运wharf 码头A3D coordinate measurement 三次元量床3D modeling 三次元模拟aberration 色差abnormal glow 不规则辉光放电abrasive 砂轮access 通路account 账户accretion 炉瘤accurate die casting 精密压铸acid converter 酸性转炉acid lining cupola 酸性熔铁炉acid open-hearth furnance 酸性平炉activator 活化剂acetylene 乙炔adjustable spanner 活动扳手aerator 松砂机after service 售后服务age hardening 时效硬化ageing 老化处理air hardening 气体硬化airless plasting cleaning 离心喷光air patenting 空气韧化air permeability test 透气性试验air set mold 常温自硬铸模。
最新消息 1-2the benefits of civilization which we enjoy today are essentiallydue to the improved quality of products available to us .文明的好处我们享受今天本质上是由于改进质量的产品提供给我们。
the improvement in the quality of goods can be achieved with proper design that takes into consideration the functional requirement as well as its manufacturing aspects. 提高商品的质量可以达到与适当的设计 , 考虑了功能要求以及其制造方面。
The design process that would take proper care of the manufacturing process as well would be the ideal one. This would ensure a better product being made available at an economicalcost. 设计过程中,将采取适当的照顾的生产过程将是理想的一个。
这将确保更好的产品被使可得到一个经济成本。
Manufacturing is involved in turning raw materials to finished products to be used for some purpose制.造业是参与将原材料到成品用于某些目的。
In the present age there have been increasing demands on the product performance by way of desirable exotic properties such as resistance to high temperatures, higher speeds and extra loads. 在现在的时代已经有越来越多的产品性能要求的理想的异国情调的性能如耐高温, 更高的速度和额外的负载 These in turn would require a variety of new materials and its associated processing这.些反过来需要各种新材料及其相关的处理 Also, exacting working conditions that are desired in the modern industrial operations make large demands on the manufacturing industry.这些反过来需要各种新材料及其相关的处理。
