当前位置：文档之家 › ASMT-MW60中文资料

ASMT-MW60中文资料

  • 格式：pdf
  • 大小：778.18 KB
  • 文档页数：11

ASMT-Mx6x & ASMT-MxHx Moonstone TM ½W Power LED Light Source Data SheetDescription½W Power LED Light Source is a high performance energy efficient device which can handle high thermal and high driving current. The exposed pad design has excellent heat transfer from the package to the motherboard. Op-tion with electrically isolated metal slug is also available The Cool White Power LED is available in various color temperature ranging from 4000K to 10000K and Warm White Power LED ranging from 2600K to 4000K.The low profile package design is suitable for a wide vari-ety of applications especially where height is a constraint. The package is compatible with reflow soldering. This will give more freedom and flexibility to the light source de-signer.Applications•Sign backlight•Safety, exit and emergency sign lightings •Specialty lighting such as task lighting and reading lights•Retail display•Commercial lighting•Accent or marker lightings, strip or step lightings Features•Available in Cool White and Warm White color •Available in diffuse and non-diffuse version •Available in both electrical isolated and non-isolatedmetal slug•Energy efficient•Exposed pad for excellent heat transfer•Suitable for reflow soldering process•High current operation•Long operation life•Wide viewing angle•Silicone encapsulation•ESD HBM Class 3B, > 8000•MSL 4 products•High junction temperature of 145°C Specifications•InGaN Technology• 3.5V, 150mA (typical)•110 viewing anglePackage Dimensions213Heatsink (2 options)a. Electrically Isolated b. Electrically non-isolatedANODENOTES:1. ALL DIMENSIONS IN MILLIMETERS.2. TOLERANCE IS ± 0.1 mm UNLESS OTHERWISE SPECIFIED.CATHODE Notes:1. All dimensions in millimeters.2. Tolerance is ± 0.1 mm unless otherwise specified.Device Selection Guide at Junction Temperature T j = 25°CColorPart NumberLuminous Flux, Φv [1,2] (lm)Test Cur-rent (mA)Metal SlugDiceTechnologyMinTypMaxCool White ASMT-MW6019.53043.0150Non-isolated InGaN Warm White ASMT-MY60152533150Non-isolated InGaN Cool White Diffuse ASMT-MWH0152543.0150Non-isolated InGaN Warm White Diffuse ASMT-MYH011.52033150Non-isolated InGaN Cool White ASMT-MW6219.53043.0150Isolated InGaN Warm White ASMT-MY62152533150Isolated InGaN Cool White Diffuse ASMT-MWH2152543.0150Isolated InGaN Warm White DiffuseASMT-MYH211.52033150IsolatedInGaNNotes:1. ΦV is the total luminous flux output as measured with an integrating sphere at 25ms mono pulse condition.2. Flux tolerance is ±10 %Part Numbering SystemASMT –Color Bin Selection Max Flux Bin Selection Min Flux Bin SelectionColorW – Cool White Y – Warm WhitePacking Option0 – Tube1 – Tape & reel6 – Clear H – Di use0 – Electrically non-isolated Metal Slug2 – Electrically Isolated Metal SlugAbsolute Maximum Ratings at T A = 25°CParameter ASMT-Mx60Units DC Forward Current [1]150mA Peak Pulsing Current [2]300mA Power Dissipation525mW LED Junction Temperature145°C Operating Ambient Temperature Range -40 to +120°C Storage Temperature Range-40 to +120°C Notes:1. DC forward current – derate linearly based on Figure 5.2. Pulse condition duty factor = 10%, Frequency = 1kHzOptical Characteristics (T A = 25°C)Part Number Color Correlated Color Temperature,CCT (Kelvin)Viewing Angle 2θ½ [1](Degrees)Luminous Efficiency(lm/W)Min Max Typ TypASMT-MW6x Cool White40001000011057 ASMT-MY6x Warm White2600400011048 ASMT-MWHx Cool White Diffuse40001000012048 ASMT-MYHx Warm White Diffuse2600400012038 Notes:1. θ½ is the off-axis angle where the luminous intensity is ½ the peak intensity.Electrical Characteristic (T A = 25°C)Dice Type Forward Voltage V F(Volts) @ I F = 150mAReverse Voltage V R(Volts)Thermal Resistance Rθj-ms(°C/W)[1]Typ.Max.Max.Typ.InGaN 3.5 4.0527 Note:1. Rθj-ms is Thermal Resistance from LED junction to metal slug.T A AMBIENT TEMPERATURE - °C200250300350IFT(mV) Figure 5. Maximum forward current vs. ambient temperature. Deratedbased on T J MAX = 145°C, RθJA = 100°C/W, 120°C/W and 140°C/WT -50300Figure 7. Recommended soldering land patternFigure 8. Temperature vs. relative forward voltage shift Figure 9. Relative LOP vs Junction Temperature for InGaN DevicesFlux Bin Limit [1] (For reference only) [X 1 X 2]BinFlux (lm) at 150mAMinMaxA 5.57.0B 7.09.0C 9.011.5D 11.515.0E15.019.5F 19.525.5G 25.533.0H33.043.0Tolerance for each bin limits is ±10 %Figure 6. Recommended Reflow Soldering TIMET E M P E R A T U R E(Acc. to J-STD-020C)A AMBIENT TEMPERATURE - °C102030405060708090100JUNCTION TEMPERATURE (°C)R E L A T I V E L O P (%)-250-200-150-100050100150200250350-40R E L A T I V E F O R W A R D V O L T A G E S H I F T (m V )-300-250-200-150-100-50050100150200250300350-40-1510356085TEMPERATURE - °CR E L A T I V E F O R W A R D V O L T A G E S H I F T (m V )元器件交易网Color Bin Selections [X3]Individual reel will contain parts from one full bin only.Cool White0Full DistributionA A onlyB B onlyC C onlyD D onlyE E onlyF F onlyG G onlyH H onlyZ A and B onlyY B and C onlyW C and D onlyV D and E onlyU E and F onlyT F and G onlyS G and H onlyQ A, B and C onlyP B, C and D onlyN C, D and E onlyM D, E and F onlyL E, F and G onlyK F, G and H onlyJ Special Color Bin1A, B, C and D only 2E, F, G and H only 3B, C, D and E only 4C, D, E and F only 5A, B, C, D and E only 6B, C, D, E, and F only Warm White0Full DistributionA A onlyB B onlyC C onlyD D onlyE E onlyF F onlyZ A and B onlyY B and C onlyW C and D onlyV D and E onlyU E and F onlyQ A, B and C onlyP B, C and D onlyN C, D and E onlyM D, E and F onlyJ Special Color Bin1A, B, C and D only 2E, F, G and H only 3B, C, D and E only 4C, D, E and F only 5A, B, C, D and E only 6B, C, D, E, and F onlyCool WhiteColor Limits (Chromaticity Coordinates)Bin A X Y 0.3670.4000.3620.3720.3290.3450.3290.369Bin B X Y 0.3620.3720.3560.3300.3290.3020.3290.302Bin C X Y 0.3290.3690.3290.3450.3050.3220.3010.342Bin D X Y 0.3290.3450.3290.3020.3110.2850.3050.322Bin E X Y 0.3030.3330.3070.3110.2830.2840.2740.301Bin F X Y 0.3070.3110.3110.2850.2900.2650.2830.284Bin G X Y 0.3880.4170.3790.3830.3620.3720.3670.400Bin HX Y0.3790.3830.3690.3430.3560.3300.3620.372Tolerances ± 0.01Warm White Color Limits (Chromaticity Coordinates)Bin A X Y 0.4520.4340.4880.4470.4700.4140.4380.403Bin B X Y 0.4380.4030.4700.4140.4520.3840.4240.376Bin C X Y 0.4070.3930.4180.4220.4520.4340.4380.403Bin D X Y 0.3950.3620.4070.3930.4380.4030.4240.376Bin E X Y 0.3810.3770.3870.4040.4180.4220.4070.393Bin FX Y0.3730.3490.3810.3770.4070.3930.3950.362Tolerances ± 0.01X - COORDINATEY - C O O R D I N A T EX - COORDINATEY - C O O R D I N A T E(Only Applicable for Color Bin A to Bin D and Bin G to Bin H)Color LimitsCool WhiteColor Limits (Chromaticity Coordinates)Bin A1X Y 0.3640.3830.3670.4000.3480.3850.3470.372Bin A2X Y 0.3640.3830.3620.3720.3460.3590.3470.372Bin A3X Y 0.3290.3570.3290.3690.3480.3850.3470.372Bin A4X Y 0.3290.3450.3290.3570.3470.3720.3460.359Bin B1X Y 0.3620.3720.3600.3570.3440.3440.3460.359Bin B2X Y 0.3600.3570.3580.3430.3430.3310.3440.344Bin B3X Y 0.3580.3430.3560.3300.3410.3140.3430.331Bin B4X Y 0.3290.3310.3290.3450.3460.3590.3440.344Bin B5X Y 0.3290.3310.3440.3440.3430.3310.3290.320Bin B6X Y 0.3430.3310.3410.3140.3290.3020.3290.320Bin C1X Y 0.3290.3690.3290.3570.3150.3440.3140.355Bin C2X Y 0.3290.3570.3290.3450.3160.3330.3150.344Bin C3X Y 0.3140.3550.3150.3440.3030.3330.3010.342Bin C4X Y0.3150.3440.3160.3330.3050.3220.3030.333Tolerances ± 0.010.240.260.280.300.320.340.360.380.400.420.440.240.260.280.300.320.340.360.380.400.420.44X - COORDINATEY - C O O R D I N A T ECool WhiteColor Limits (Chromaticity Coordinates)Bin D1X Y 0.3290.3450.3290.3310.3170.3200.3160.333Bin D2X Y 0.3290.3310.3290.3200.3180.3100.3170.320Bin D3X Y 0.3290.3200.3290.3020.3200.2930.3180.310Bin D4X Y 0.3160.3330.3170.3200.3070.3110.3050.322Bin D5X Y 0.3170.3200.3180.3100.3090.3000.3070.311Bin D6X Y 0.3180.3100.3200.2930.3110.2850.3090.300Bin G1X Y 0.3920.4210.3860.4000.3640.3830.3670.400Bin G2X Y 0.3860.4000.3820.3850.3620.3720.3640.383Bin H1X Y 0.3820.3850.3780.3700.3600.3570.3620.372Bin H2X Y 0.3780.3700.3750.3580.3580.3430.3600.357Bin H3X Y0.3750.3580.3710.3440.3560.3300.3580.343Package Tube – Option 0Tape & Reel – Option 1DimValueAO 8.80±0.10BO 16.45±0.10KO3.60±0.10W 24.0±0.10P 16.0±0.10Qty/Reel250EAUnit: mmFRONT VIEWTOPVIEWDISCLAIMER: AVAGO’S PRODUCTS AND SOFTWARE ARE NOT SPECIFICALLY DESIGNED, MANUFACTURED OR AUTHO-RIZED FOR SALE AS PARTS, COMPONENTS OR ASSEMBLIES FOR THE PLANNING, CONSTRUCTION, MAINTENANCE OR DIRECT OPERATION OF A NUCLEAR FACILITY OR FOR USE IN MEDICAL DEVICES OR APPLICATIONS. CUSTOMER IS SOLELY RESPONSIBLE, AND WAIVES ALL RIGHTS TO MAKE CLAIMS AGAINST AVAGO OR ITS SUPPLIERS, FOR ALL LOSS, DAMAGE, EXPENSE OR LIABILITY IN CONNECTION WITH SUCH USE.For product information and a complete list of distributors, please go to our web site: Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries.Data subject to change. Copyright © 2005-2008 Avago Technologies. All rights reserved.AV02-1319EN - July 2, 2008Handling Precaution:The encapsulation material of the product is made of sili-cone for better reliability of the product. As silicone is a soft material, please do not press on the silicone or poke a sharp object onto the silicone. These might damage theReel Dimensionproduct and cause premature failure. During assembly or handling, the unit should be held on the body (white ep-oxy).元器件交易网。

合集下载

ASMEagle-60密码和重要参数

ASMEagle-60密码和重要参数

ASMEagle-60密码和重要参数ASM Eagle-60 密码和重要参数ASM Eagle-60密码F15=2002 F16=2009 菜单的锁与解锁=AB33901.AB33902.AB33903.AB33904F1-5 XY工作台之座标显示F1-6 量两点之间的距离F1-15 密码2002F1-16 密码2009F1-17 更换焊咀F1-18 超声波功率输出F1-24 打开轨道F1-88 锁定/松开X马达F1-99 植球开关（BSOB或BBOS)F1-100 机台系统版本显示F1-110 XYZ马达归位F1-168 更换线的类型F1-169 线群组的显示F1-900 Force Ratio资料显示F1-995 锁定菜单预设的密码LeveL 1密码 AB33901LeveL 2密码 AB33902LeveL 3密码 AB33903LeveL 4密码 AB33904线弧＝9002还有用这些都打不开的话就用：（2位数的日子+50）X（2位数的月份+50）得出4位数字（ABCD）然后头尾互换，密码便是（DBCA）如今天的日期是8月5号，（05+50）X（08+50）=55X58=3190，头尾数安互换后便是0193，利用这个密码便可以开启如：WH Menu内的Factory Setup重要参数位置及影响SetupPower Calibration路径: Main \ setup \ more ..\ power Calibration …\影响: 此为机台设定，将影响power 输出值，不准更动Auto Bond 前确认之开关Enable PR路径: main \ auto \ enable PR yes影响: 此为auto bond PR之开关Auto Index路径:Main \ Auto \ auto Index Yes影响: 此项功能为LF 自动输送，假如此auto index 关闭，则auto bond 时无法自动送导线架Ball Detect路径:Main \ Auto \ Ball Detect Yes影响：此开关为烧球之侦测如选NO，无侦测可能造成空卬Stick Detect 1路径:Main \ Auto \ Stick Dectect 1 Yes影响：此为第一点侦测（１st bond Non-stick ）之开关，如关闭则不侦测Stick Detect 2路径:Main \ Auto \ Stick Dectect 2 Yes影响：此为第一点侦测（２st bond Non-stick ）之开关，如关闭则不侦测Heater Alarm路径:Main \ Auto \ More \ Heater Alarm Yes影响：此为检查热板及预热板温度侦测是否超出设定范围，yes 表未到达设定温度时，警告ＶLL Retry路径:Main \ Auto \ More \ VLL Retry No影响：第一次VLL寻找失败时，重新找寻ＶＬＬEnable Index路径:Main \ Auto \ More \ Enable PR Index Every影响：爪夹在运送时，每一unit 皆以 Index PR 作定位影响品值之重要参数TaiBar (.01mil )路径:Main \ Auto \ More \TaieBar (.1 mil ) XX影响：此为设定TaiBar 之公差Alignment Tolerance路径:Main \ Parameter \ Bond Parameter \ Alignment Tolerance L / D XX X影响:此为设定手动平移点位置与原本教定的平移点容许的偏移量/ Search Delay路径:Main \ Parameter \ Bond Parameter \ Search Delay (ms) L / D XX XX影响: PR 辨识前的延迟时间Search Range路径:Main \ Parameter \ Bond Parameter \ Search Range (id )L / D XX XX影响: PR 搜寻的范围Fire Level路径:Main \ Parameter \ Bond Parameter \ Fire level XXX影响:E_torch 和capillary 之间的距离，如改变会影响侦测烧球之功能判定Gap Wide Warning Volt路径:Main \ Parameter \ Bond Parameter \ EFO Control \ EFO Parameter \ Gap Wide Warning Volt XXX影响：打火的电压大小EFO Current路径:Main \ Parameter \ Bond Parameter \ EFO Control \ EFO Parameter \ EFO Current (*0.01)影响:打火的电流大小Enable Dual FAB路径:Main \ Parameter \ Bond Parameter | EFO Control \ EFO Setting \ Enable Dual FAB NO影响:此为烧大小球的开关Heater Control路径:Main \ parameter \ Bond Parameter \ Heater Control影响: 热板及预热板的控制系统VLL Lead Position Tol路径:Main \ Parameter \ Bond Parameter \ More \ VLL Lead Position T ol (%)影响:VLL寻找时所能允许的偏移量VLL Lead Width Tolerance路径:Main \ Parameter \ Bond Parameter \ more \ VLL Lead Width T olerance um影响:VLL寻找时，所能允许导线架本身宽度变化的容忍值Edit Stick Dection1路径:Main \ Wire Parameter \ Edit Non –Stick Detection \ Edit Stick Detection 1影响:第一焊点的个别侦测开关Edit Stick Detection 2路径:Main \ Wire Parameter \ Edit Non- Stick Detection \ Edit Stick Detection 2影响:第二焊点的个别侦测开关Capillary Limit路径:Main \ show statistics \ set statistics limit …\ Capil Warn XXXX *100路径:Main \ Show Statistic \ Set Statistics Limit …\ Capil Stop XXx * 100影响:自动打线时的焊针次数1 st / L R offset路径:Main \ WH Menu ..\ Service ..\ Control Parameter \ Miscellaneous…\ 1 st / L R offset Update NO影响:如开yes 会输送导线架时会自动更新所补偿的偏移量Edit Bond PT Tol .路径: F15 \ Bonding Control \Safety Control \Edit Bond PT Tol .影响:当修改打线位置时，所允许的修改范围侦测设定tail short路径: Main \ Auto \ Start single Bond \ 9 Tail shortRange: -15 到15 ，通常设-2 到2设为-15 表侦测功能关闭stickadj路径:Main \ Auto \ Start Single Bond \ F1 \ 7StickadjRange: sample值为５到３０设为３５表侦测功能关闭正常设定值须高single Bond时之 sample 值如设定值低于Single Bond 之sample值则假侦测关键：1须tail break Control off2路径:Main \ Wire Parameter \ More \ Edit Tail Break Control 相对开关：1 stick detect 1路径:Main \ Auto \ More \ Stick Detect 12 stick detect 2路径:Main \ Auto \ More \ Stick Detect 23 edit Non-Stick Detection路径:Main \ Wire Parameter \ Edit Non-Stick DetectionTail Stick路径:Main \ Auto \ Start Single Bond \ F1 \ 9Tail stickRange: sample值为20 到170正常设定值须高single Bond时之 sample 值如设定值低于Single Bond 之sample值则假侦测关键：1须tail break Control YES2路径:Main \ Wire Parameter \ More \ Edit Tail Break Control BFM路径:F15(2002)\ Bonding Control \ EFO Control \ Ball Formation \ Monitor …\ Enable BFM 程序: 1设定sampling bons (redo) xx2设定contamination level x3设定Abnormality level x4切换enable BFM5 auto bond 时自动取样影响:侦测烧球对应开关: ball detect (main\ auto \ ball detect)Bond Stick Detection路径: F15 (2002)\ Bonding Control \ Bond Stick Detection程序:1设定total sample xx (取样数值)2切换enable sample yes 3 auto bond 时自动取样影响:侦测一焊点之灵敏度。

ASM设备中文资料文档

ASM设备中文资料文档

ASM设备中文资料文档ASM设备中文资料ASM Teach流程一.设定及教读L/F二.设定及教读Mag.三.调整各部位的M/C data四.教读L/F Index五.教读Index PR六.教读Aligment七.Teach 1st PR及1st Backup PR八.Teach wire九.Teach Local lead (VLL)十.换针及金线十一.执行contact search 及reference parameter十二.执行Bond center十三.check各项参数( Bond、Base、Loop、Light、auto、funtion )十四.储存Date设定L/F Type data:一. 6 W/H Menu ?二. 0 W/H Setup ?三. 0 Change Device ?此项用以设定L/F的参数。

0 Device Name 可用以设定L/F的名称,机台最多支持8个字符的名称。

1 Number Scale 机台支持两种型态的单位表示:mil及mCM,其中mCM表示CM/10002 Number Of Unit 表示每条导线架上有多少个units。

3 Device Width 表示L/F的宽度。

4 Device Pitch 两个Device间的距离。

5 Rad to index hole 索引孔的半径。

6 Center Index hole 询问索引孔是否在两个Die Pad的中央位置。

7 Rail edge to index hole 表L/F边缘至索引端的距离。

L/F WIDTH教读一. 6 W/H MANU ?二. 0 W/H SETUP ?三. 2 LEARNING LF PARA ?四. 0 LEARN LF WIDTH ?步骤: 1.当进入时流道会做一次原点归值动作, 再回到原来未调整前宽度。

2.此时使用上、下键即可调整流道宽度。

3.完成调整后, 按STOP键跳出, 此时画面会SHOW出是否要UPDATE , 选择YES即OK。

ASMT-LW60中文资料

ASMT-LW60中文资料

R S Tolerance: ±15%
Minimum
112.5 180.0
Maximum
180.0 285.0
White Intensity (mcd) Bin ID
W1 W2 W3 Tolerance: ±15%
Green 200 1400 1600
Pin 1
Pin 4
Flexible light strip length = 200mm Standard Part Number = ASMT-Lx60 Notes: 1. All dimensions in millimeters (Inches). 2. Tolerances are ± 0.1mm [0.004 IN.] Unless otherwise specified. . Strip diameter ø1.4mm. Pin 1 Pin 2 Pin Pin 4 Vcc for LED 1 Ground for LED 1 Vcc for LED 2 Ground for LED 2
12.1
Minimum
11.9
Typical
12.0
Typical
20
Note: 1. For each individual LED + resistor string. 2. Resistor value is determined by forward voltage of LED.

元器件交易网
Features
• • • • • • Outstanding abrasion resistance Excellent mechanical properties Excellent chemical resistance Excellent light transitivity High shaping flexibility Available length 100mm to 500mm at interval of 1mm • Available voltage source : 5V, 9V and 12V • Available color: Blue, Green, Red and White • Light strip module in straight configuration
STPS60SM200CW;中文规格书,Datasheet资料

STPS60SM200CW;中文规格书,Datasheet资料

May 2011Doc ID 018819 Rev 11/7STPS60SM200CPower Schottky rectifierFeatures■High reverse voltage (200 V)■Low forward voltage drop ■High frequency operationDescriptionThe STPS60SM200C is a dual Schottky rectifier suited for high frequency switched-mode power supply.Housed in TO-247, this device is especially suited for use in telecom base station SMPS, providing these applications with a good efficiency at both low and high load.Table 1.Device summarySymbol Value I F(AV) 2 x 30 A V RRM 200 V T j (max)175 °C V F (typ)640 mVCharacteristics STPS60SM200C2/7Doc ID 018819 Rev 11 CharacteristicsWhen the two diodes 1 and 2 are used simultaneously:ΔT j (diode 1) = P(diode 1) x R th(j-c)(Per diode) + P(diode 2) x R th(c)To evaluate the conduction losses use the following equation: P = 0.58 x I F(AV) + 0.0037 x I F 2(RMS)Table 3.Thermal resistanceSymbol ParameterValue UnitR th(j-c)Junction to case Per diode 0.7°C/W Total0.5R th(c)Coupling0.3Table 4.Static electrical characteristics (per diode)Symbol ParameterTest conditions Min.Typ.Max.Unit I R (1)Reverse leakage currentT j = 25 °C V R = V RRM 0.05mAT j = 125 °C 613V F (2)Forward voltage dropT j = 25 °C I F = 7.5 A 0.670.70V T j = 125 °C 0.510.55T j = 25 °C I F = 15 A 0.730.77T j = 125 °C 0.570.61T j = 25 °C I F = 30 A0.790.83T j = 125 °C0.640.691.Pulse test: t p = 5 ms, δ < 2%2.Pulse test: t p = 380 µs, δ < 2%STPS60SM200CCharacteristicsDoc ID 018819 Rev 13/7Figure 1.Average forward power dissipation versus average forward current Figure 2.Average forward current versus ambient temperature (δ = 0.5)T= t /Tp t Figure 3.Non repetitive surge peak forward current versus overload duration Figure 4.Relative variation of thermalimpedance junction to case versus tFigure 5.Reverse leakage current versus reverse voltage applied Figure 6.Junction capacitance versus reverse voltage appliedCharacteristics STPS60SM200C4/7Doc ID 018819 Rev 1Figure 7.Forward voltage drop versus forward currentFigure 8.Forward voltage drop versus forward currentSTPS60SM200C Package informationDoc ID 018819 Rev 15/72 Package information●Epoxy meets UL94, V0●Cooling method: by conduction (C)●Recommended torque value: 0.55 to 1.0 N·mIn order to meet environmental requirements, ST offers these devices in different grades ofECOPACK ® packages, depending on their level of environmental compliance. ECOPACK ® specifications, grade definitions and product status are available at: . ECOPACK ® is an ST trademark.Ordering information STPS60SM200C6/7Doc ID 018819 Rev 13 Ordering information4 Revision historyTable 6.Ordering informationOrder code Marking Package Weight Base qty Delivery modeSTPS60SM200CWSTPS60SM200CWTO-2474.45 g30TubeTable 7.Document revision historyDate RevisionChanges17-May-20111First issue.STPS60SM200CPlease Read Carefully:Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice.All ST products are sold pursuant to ST’s terms and conditions of sale.Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein.No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein.UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST.ST and the ST logo are trademarks or registered trademarks of ST in various countries.Information in this document supersedes and replaces all information previously supplied.The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.© 2011 STMicroelectronics - All rights reservedSTMicroelectronics group of companiesAustralia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of AmericaDoc ID 018819 Rev 17/7分销商库存信息: STMSTPS60SM200CW。