DIN7168德国标准

德国标准和国际标准、中国标准中英文对照表序号德国标准中文品名英文品名国际标准中国标准Item DIN-Standard Description in Chinese Description in English ISO-Standard GB-Standard1 DIN1 圆锥销taper pins ISO2339 GB1172 DIN7 圆柱销parallel pins ISO2338 GB119-863 DIN84 开槽圆柱头螺钉slotted cheese head screws ISO1207 GB65-854 DIN85 开槽盘头螺钉slotted pan head screws ISO1580 GB67-855 DIN93 单耳止动垫圈tab washers GB8546 DIN94 开口销split cotter pins ISO1234 GB917 DIN95 开槽半沉头木螺钉slotted raised csk head wood screws GB1018 DIN96 开槽半圆头木螺钉slotted round head wood screws GB999 DIN97 开槽沉头木螺钉slotted countersunk head wood screws GB10010 DIN125-A 平垫plain washers ISO7089 GB97.1-8511 DIN125-B 平垫(带倒角) mediun washers ISO7090 GB97.2-8512 DIN126 平垫plain washers ISO709113 DIN127-A 重型弹垫spring lock washers,tang ends GB724414 DIN127-B 标准弹垫spring lock washers,square ends GB93-8715 DIN128-A 鞍形弹垫single coil spring lock washers GB7245-8716 DIN137-A 弹簧止动垫圈curved spring washers17 DIN137-B 波形弹垫wave spring washers GB95518 DIN186 T型方颈螺栓T-head bolts with square neck GB37-8819 DIN188 T型双接头螺栓T-head bolts with double nip20 DIN258 螺纹圆锥销taper pins with threaded end ISO873721 DIN261 T型头螺栓T-head bolts22 DIN315AF 蝶型螺母(美制) wing nuts amercia form23 DIN315DF 蝶型螺母(德制) wing nuts germany form GB62-8824 DIN316AF 蝶型螺钉(美制) wing screws amercia form25 DIN317DF 蝶型螺钉(德制) wing screws germany form26 DIN319 圆球型盖型螺母ball knobs27 DIN404 开槽带孔球面圆柱头螺钉slotted capstan screws GB832-8828 DIN417 开槽长圆柱端紧定螺钉slotted set srews with full dog point ISO7435 GB75-8529 DIN427 开槽平端紧定螺钉(半牙) slotted set srews with chamfered end ISO2342 GB73-8530 DIN431 小六角特薄细牙螺母pipe nuts with thread GB808-8831 DIN432 外舌止动垫圈external tap GB856-8832 DIN433 小垫圈(用于圆柱头螺钉) washers for cheese head screws ISO7092 GB848-9533 DIN434 方斜垫圈(U型) square taper washers for U-section GB852-8834 DIN435 方斜垫圈(I型) square taper washers for I-sections GB852-8835 DIN436 方垫圈square washers36 DIN438 开槽凹端紧定螺钉slotted set with cup point ISO7436 GB74-8537 DIN439 六角薄螺母hexagon thin nuts ISO4035 GB6172-8638 DIN439 细牙六角薄螺母hexagon thin nuts ISO8675 GB6173-8639 DIN440 木螺钉专用垫圈rounds washers for wood constructions ISO709440 DIN443 密封帽sealing caps,push-in type41 DIN444 活节螺栓B 型eye bolts form B GB798-8842 DIN462 内舌止动垫圈internal tab washers43 DIN463 双耳止动垫圈washers with two taps GB855-8844 DIN464 滚花高头螺钉knurled thumb screws with collar GB834-8845 DIN465 开槽滚花高头螺钉slotted knurled thumb screws with collar46 DIN466 滚花高螺母knurled thumb nuts with collar GB806-8847 DIN467 滚花薄螺母knurled thumb thin nuts GB807-8848 DIN470 锁紧垫圈sealing washers49 DIN471 轴用弹性挡圈retaining rings for shafts(external),circlips GB894.1-8650 DIN472 孔用弹性挡圈retaining rings for bores(internal),circlips GB893.1-8651 DIN478 方头带垫螺栓square head bolts with collar52 DIN479 方头圆柱底端螺栓square head bolts with half dog point53 DIN480 方头带垫半圆底端螺栓square head bolts with collar,half dog point and rounded end54 DIN508 T型槽螺母T-slot nuts ISO29955 DIN525 单头螺柱single end studs56 DIN529 地脚螺栓masonry bolts GB799-8857 DIN546 带槽圆螺母slotted round nuts GB817-7658 DIN547 端面带孔圆螺母round nuts with drilled holes in one face GB815-8859 DIN551 开槽平端紧定螺钉slotted sit screws with flat point ISO4776 GB73-8560 DIN553 开槽锥端紧定螺钉slotted set screws with cone point ISO7434 GB71-8561 DIN555 六角螺母hexagon nuts ISO403462 DIN557 方螺母-C square nuts GB39-8863 DIN558 六角头螺钉hexagon screws ISO401864 DIN561 六角头圆柱端紧定螺钉hexagon set screws with full dog point65 DIN562 薄型方螺母-B square nuts without bevel(pressed nuts)66 DIN571 六角头木螺钉hexagon head wood screws (coach screws) GB102-8667 DIN580 吊环螺钉lifting eye bolts ISO3266 GB825-7668 DIN582 吊环螺母lifting eye nuts69 DIN601 六角头螺栓hexagon bolts ISO401670 DIN603 大半圆头方颈螺栓(马车螺栓) mushroom head square neck bolts (carriage bolts) ISO8677 GB14-8871 DIN604 沉头带插销马车螺栓flat countersunk nib bolts72 DIN605 沉头长方颈马车螺栓flat countersunk long square neck bolts73 DIN607 半圆头带插销马车螺栓cup head nib bolts74 DIN608 沉头短方颈马车螺栓flat countersunk short square neck bolts75 DIN609 六角头精配螺栓（长螺纹）hexagon fitted bolts,long thread76 DIN610 六角头精配螺栓（短螺纹）hexagon fitted bolts,short thread77 DIN653 滚花平头螺钉knurled thumb screws thin type GB835-8878 DIN660 半圆头铆钉round head rivets ISO1051 GB867-8679 DIN661 沉头铆钉contersunk head rivets ISO1051 GB869-8680 DIN662 半沉头铆钉raised contersunk head rivets ISO105181 DIN674 大扁头铆钉mushroom head rivets ISO105182 DIN703 重型侧面带孔圆螺母adjusting rings,heavy range (shafting collars)83 DIN705 侧面带孔圆螺母adjusting rings,light range (shafting collars) GB816-8884 DIN741 卡头wire rope clips85 DIN787 T型槽螺钉T-slot screws ISO29986 DIN835 双头螺柱（牙长=2D）studs-metal (end=2d) GB900-8887 DIN906 内六角锥型闭锁螺钉hexagon socket pipe plugs,conical thread88 DIN908 内六角直型闭锁螺钉hexagon socket screw plugs,cyl. thread89 DIN909 外六角锥型闭锁螺钉hexagon head pipe plugs,conical thread90 DIN910 外六角直型闭锁螺钉hexagon head screw plugs,cyl.thread91 DIN911 内六角扳手socket wrenches ISO293692 DIN912 内六角圆柱头螺钉hexagon socket cap screws ISO4762 GB70-8593 DIN913 内六角平端紧定螺钉hexagon socket set screws with flat point ISO4026 GB77-8594 DIN914 内六角尖端紧定螺钉hexagon socket set screws with cone point ISO4027 GB78-8595 DIN915 内六角圆柱端紧定螺钉hexagon socket set screws with dog point ISO4028 GB79-8596 DIN916 内六角凹端紧定螺钉hexagon socket set screws with cup point ISO4029 GB80-8597 DIN917 薄型盲螺母hexagon cap nuts98 DIN920 开槽小圆柱头螺钉slotted short cheese head screws99 DIN921 开槽大圆柱头螺钉slotted large cheese head screws GB838-88100 DIN923 开槽圆柱头轴肩螺钉slotted pan head screws with shoulder GB830-88101 DIN927 开槽无头轴肩螺钉slotted shoulder screws102 DIN928 焊接方螺母square weld nuts GB/T13680-92103 DIN929 焊接六角螺母hexagon weld nuts GB/T13681-92104 DIN931 六角头螺栓（半牙）hexagon head screws ISO4014 GB5782-86105 DIN933 六角头螺栓（全牙）hexagon head screws ISO4017 GB5783-86106 DIN934 六角头螺母(1型) hexagon full nuts ISO4032 GB6170-86107 DIN934 细牙六角头螺母(1型) hexagon full nuts ISO8673 GB6171-86108 DIN935 开槽六角螺母hexagon slotted and castle nuts ISO7035 GB6178-86109 DIN936 六角头薄螺母hexagon thin nuts ISO4035 GB6172.1-86110 DIN937 六角头开槽薄螺母hexagon thin slotted and castle nuts ISO7038 GB6181-86111 DIN938 双头螺距（牙长=1D）studs metal (end=1d) GB897-88112 DIN939 双头螺距（牙长=1.25D）studs metal (end=1.25d) GB898-88113 DIN940 双头螺距（牙长=1.5D）studs metal (end=1.5d)114 DIN960 六角头细牙螺栓（半牙）hexagon head bolts,metric fine pitch thread ISO8765 GB5785-86115 DIN961 六角头细牙螺栓（全牙）hexagon head bolts,metric fine pitch thread ISO8676 GB5786-86116 DIN962 头部穿孔六角头螺栓additional shapes and versions for bolts117 DIN963 开槽沉头螺钉slotted countersund head screws ISO 2009 GB68-85118 DIN964 开槽半沉头螺钉slotted raised countersunk oval head screws ISO 2010 GB69-85 119 DIN965 十字槽沉头螺钉cross recessed countersunk head screws ISO7046 GB819-85120 DIN966 十字槽半沉头螺钉cross recessed raised countersunk head screws ISO7047 GB820-85121 DIN970 六角头螺母hexagon nuts type-1122 DIN971 六角头螺母hexagon nuts type-2123 DIN972 细牙六角头螺母(2型) hexagon nuts with fine thread ISO8674 GB6176-86124 DIN975 牙条(全螺纹) threaded rods(studdings) GB15389-94125 DIN976 螺纹销threaded pins(stud bolts)126 DIN979 六角头开槽薄螺母（2型）hexagon thin slotted and castle nuts127 DIN980 全金属六角锁紧螺母（1型）prevailling torque type hexagon nuts,all metall nuts ISO7199 GB6184-86128 DIN981 圆螺母locknuts ISO2982 GB812-88129 DIN982 六角头尼龙锁紧螺母prevailling torque type hexagon nuts,heavy type ,with nylon insert ISO7040 GB889.1-86130 DIN985 六角头薄型尼龙锁紧螺母prevailling torque type hexagon nuts,heavy type ,with nylon insert ISO10511 GB6172.2-86131 DIN986 六角盖型尼龙锁紧螺母prevailling torque typedomed capnuts with nylon insert132 DIN988 配合垫片shim rings133 DIN1052 木材连接用垫片washers for timber connectors134 DIN1151 沉头钢钉round plain head nails135 DIN1440 销钉专用垫片A型plain washers for clevis pins(A型) ISO8738136 DIN1441 销钉专用垫片plain washers for clevis pins137 DIN1444 带头销钉clevis pins with head ISO2341138 DIN1471 圆锥型槽销grooved pins,taper grooved ISO8744 GB/T13829.2139 DIN1472 圆锥型槽销(半槽) grooved pins,taper grooved half length ISO8745 GB/T13829.2 140 DIN1473 平行槽销(带倒角) grooved pins,parallel grooved full length ISO8740141 DIN1474 前端凹槽槽销grooved pins,reserve grooved half length ISO8741142 DIN1475 中部凹槽槽销grooved pins,centre grooved ISO8742143 DIN1476 圆头槽销grooved pins with round head ISO8746 GB/T13829.3144 DIN1477 沉头槽销grooved pins with countersunk head ISO8747145 DIN1479 六角螺母棒turnuckles(centre parts),made out of hexagon bar146 DIN1480 花篮螺栓turnuckles with eye bolt and hook bolt147 DIN1481 弹性圆柱销spring pins,heavy type ISO8752 GB879-86148 DIN1587 组合式盖型螺母hexagon domed cap nuts GB802-88149 DIN1804 开槽圆螺母（配合沟头扳手）slotted round nuts for hook spanner150 DIN1816 圆螺母（带插销孔）round nuts with set holes151 DIN2093 盘型弹簧垫圈disc springs152 DIN3017 喉箍hose clamps153 DIN3404 润滑油嘴（旋扭头）lubricating nipples,button head154 DIN3567 管夹shackles for conduilts155 DIN3570 U型螺栓stirrup bolts(U-bolts)156 DIN6319 球面垫圈spherical washers,conical seats GB849-88157 DIN6325 圆柱销parallel pins ISO8734158 DIN6330 厚六角螺母hexagon nuts ,1.5d GB56-88159 DIN6331 厚六角法兰面螺母hexagon nuts ,1.5d with collar GB6177-86160 DIN6334 长六角螺母hexagon nuts ,3d161 DIN6797-A 外齿锁紧垫圈external teeth lock washers GB862.1-87162 DIN6797-I 内齿锁紧垫圈internal teeth lock washers GB861.1-87163 DIN6798-A 外锯齿锁紧垫圈external teeth serrated lock washers GB862.2-87164 DIN6798-I 内锯齿锁紧垫圈internal teeth serrated lock washers GB861.2-87165 DIN6799 开口挡圈retaining rings for shafts(E-rings),circlips GB896-76166 DIN6885 平键（A型）parallel keys(form A ) ISO773/2491167 DIN6888 半圆键woodruff keys ISO3912168 DIN6899 嵌环（支撑环）thimbles169 DIN6900 机器螺钉和垫圈组合件screws and washers assemblies GB9074.1-.17170 DIN6901 自攻螺钉和垫圈组合件tapping screws and washers assemblies GB9074.18-.23 171 DIN6912 薄型带孔内六角圆柱头螺钉hexagon socket head cap screws with hole,low head 172 DIN6914 大六角头螺栓hexagon head bolts with large head(friction grip bolts)173 DIN6915 大六角螺母hexagon nuts with large wideth across flat(friction grip nuts)174 DIN6916 大垫圈round washers for friction grip bolts175 DIN6917 楔型方垫圈spuare taper washers for friction grip bolts on T-sections176 DIN6923 六角法兰面螺母hexagon flange nuts ISO4161 GB6177-86177 DIN6925 全金属六角锁紧螺母(2型）prevailing torque type hexagon nuts,all metallic nuts ISO7042 GB6185.1-2000178 DIN7337 开口型抽芯铆钉（沉头、扁圆头）blind rivets GB12617/12618179 DIN7338 扁平头半空心/全空心铆钉rivets for brake and clutch lining GB875/975-86180 DIN7343 螺旋夹紧销spiral pins ISO8750181 DIN7346 轻型弹性圆柱销spring pins,light type ISO13337182 DIN7349 重型弹性圆柱销用垫圈washers for bolts with heavy type spring pinss183 DIN7500 ISO公制螺纹螺钉(多种头型) threadforming screws for ISO-metric thread184 DIN7504 自攻自钻螺钉(多种头型) self-drilling tapping screws185 DIN7513 开槽切削螺纹螺钉(多种头型) thread cutting screws186 DIN7516 十字槽切削螺纹螺钉(多种头型) thread cutting screws cross recess187 DIN7965 T型四爪螺母tee nuts with pronge188 DIN7968 钢结构用六角头螺栓连接副hexagon head fitted bolts for steel structures GB1228/1229/1230189 DIN7971 开槽盘头自攻螺钉pan head tapping screws with slot ISO1481 GB5282-85190 DIN7972 开槽沉头自攻螺钉countersunk flat head tapping screws with slot ISO1482 GB5283-85191 DIN7973 开槽半沉头自攻螺钉raised countersunk oval head tapping screws with slot ISO1483 GB5284-85192 DIN7976 六角头自攻螺钉hexagon tapping screws ISO1479 GB5285-85193 DIN7980 圆柱头螺钉用弹簧垫圈spring lock washers for screws with cylindrical heads ISO8738194 DIN7981 十字槽盘头自攻螺钉pan head tapping screws with cross recessed ISO 7049 GB845-85195 DIN7982 十字槽沉头自攻螺钉countersunk flat head tapping screws with cross recessed ISO7050 GB846-85196 DIN7983 十字槽半沉头自攻螺钉raised countersunk oval head tapping screws with cross recessed ISO7051 GB847-86197 DIN7984 薄型内六角圆柱头螺钉hexagon socket head cap screws with，reduced head198 DIN7985 十字槽盘头螺钉pan head screws with cross recessed ISO7045 GB818-85199 DIN7989 钢结构用垫圈washers for steel structures GB1230-84200 DIN7990 钢结构用六角头螺栓hexagon head bolts for steel structures GB1229-84201 DIN7991 内六角沉头螺钉hexagon socket countersunk head screws ISO10642202 DIN7993 轴用钢丝挡圈roundwire snap rings for shafts GB895.2-86203 DIN7995 十字槽半沉头木螺钉cross recessed raised countersunk head wood screws GB952-86204 DIN7996 十字槽圆头木螺钉cross recessed round head wood screws GB950-86205 DIN7997 十字槽沉头木螺钉cross recessed countersunk head wood screws GB951-86206 DIN8140 螺纹护套（普通\自锁等）ciol inserts,coarse,fine thread,silf locking207 DIN9021 大外径垫圈washers,outside diameter appro.3d ISO7093 GB96-85208 DIN11024 弹簧卡子spring cotter for a bolt209 DIN13257 平板螺栓belting bolts (elevator bolts)210 DIN18182 干壁钉（墙板钉）dry wall screws211 DIN28129 环型螺母lifting nuts(eye nuts) GB63-88212 DIN70952 圆螺母用止退垫圈tab washers for slotted round nuts GB858-88。

耐热铸钢和热强铸钢标准对照表：
标准内容：
5.3.3 耐热铸钢和热强铸钢*
（1）德国DIN标准耐热铸钢[DIN 17465—1993]
a.耐热铸钢的钢号与化学成分，见表5-64。

表5-64 耐热铸钢的钢号与化学成分（质量分数）（%）
b.耐热铸钢的室温力学性能，见表5-56。

表5-56 耐热铸钢的室温力学性能
c.耐热铸钢的高温力学性能，见表5-66。

表5-66 耐热铸钢的高温力学性能
（2）德国DIN标准铁素体热强铸钢[DIN 17245—1987]
a.铁素体热强铸钢的钢号与化学成分，见表5-67。

表5-67 铁素体热强铸钢的钢号与化学成分（质量分数）（%）
b.铁素体热强铸钢的力学性能，见表5-68。

表5-68 铁素体热强铸钢的力学性能。

91.04 合同号：0008第2页 DIN 71683 关于线性和角度尺寸的一般公差 3.1 线性尺寸公差等级关于名义尺寸(mm)范围的偏差(mm )0.51) 到 3 大于 3 到 6 大于 6 到 30 大于 30 到 120 大于 120 到 400 大于 400 到 1000 大于 1000 到 2000 大于 2000 到 4000 大于 4000 到 8000大于 8000 到 12000 大于 12000 到 16000 大于 16000 到 20000 f (精密) ±0.05 ±0.05 ±0.1 ±0.15 ±0.2 ±0.3 ±0.5 ±0.8 - - - m (中等) ±0.1 ±0.1 ±0.2 ±0.3 ±0.5 ±0.8 ±1.2 ±2 ±3 ±4 ±5 ±6 g (粗糙) ±0.15 ±0.2 ±0.5 ±0.8 ±1.2 ±2 ±3 ±4 ±5 ±6 ±7 ±8 sg (最粗) - ±0.5 ±1 ±1.5 ±2 ±3 ±4 ±6 ±8 ±10±12±121) 在名义尺寸小于0.5mm 情况下，在名义尺寸处直接标注偏差。

表2. 关于半径R(示例参见插图1)和斜边高度h(斜度)(参见图2的例子)的上下偏差公差等级 关于短边名义尺寸范围角度单元中的偏差，mm大于10 大于10 到50 大于50 到120 大于120到400大于400公差等级关于名义尺寸(mm)范围的偏差，mm f (精密)±1º ±30′ ±20′ ±10′ ±5′ m (中等)0.51) 到3大于3 到 6 大于6 到 30 大于30 到 120 大于120 到 400g (粗糙) ±1º30′ ±50′ ±25′ ±15′ ±10′ sg (最粗)±3º±2º±1º ±30′ ±20′f (精密)±0.2 ±0.5 ±1 ±2 ±44 形状和位置的一般公差4.1 按照DIN ISO 8015规定公差的原则当图纸包含提示“公差按ISO 8015的规定”的时候，应用DIN ISO 8015规定公差原则所确定的一般公差。

DK621.753.1:621.7:621.9:744.43 德国标准 1991年4月3 长度、角度通用公差 3.1长度表2：圆半径R （示例，参阅图1）及坡口高度h 表3：角度的上、下限公差图1 图23.2角度角度的通用公差不取决于长度的实际尺寸。

也就是说，无论是带有最大材料尺寸的部件，还是带有最小材料尺寸的部件，都可以出现角度偏差。

上、下限公差不会限制构成边或面的角的形状偏差。

最小条件的定义，参阅DIN ISO1101）4 形状、位置通用公差4.1根据DIN ISO8015，公差定义原理仅当图纸中含有“公差定义ISO8015”字样时，才可以使用根据DIN ISO8015公差定义原理而制定的通用公差。

形状、位置通用公差不取决于成型部件的实际尺寸。

必须遵守每个公差。

因此，也可讲形状、位置通用公差使用在带有通用最大材料尺寸的成型部件上。

配合关系额外要求限制性的包裹条件，该条件应在图纸中特殊标注。

（参阅注解）4.1.1形状通用公差4.1.1.1直度、平度表4中，已注明了直度、平度的通用公差。

在选用表中数值时，应注意：相应直线的长度与直度公差相配合；面或圆面直径的较大侧面长度与平度公差相配合。

4.1.1.2圆度圆度通用公差与直径公差的数值相同，但不可以大于表6中所标注的径向振摆数值。

（参阅注解）4.1.1.3圆柱形状没有规定圆柱体形状的通用公差。

注解：在配合圆柱面时，首先应使用包裹条件，然后根据DIN ISO8015标注带有○E符号的尺寸。

如：Ø25○E 或Ø25H7○E。

4.1.2位置通用公差4.1.2.1平行度平行度的偏差限界，从直度或平度（参阅章节4.1.1.1）或平行线或面间距离尺寸公差得出。

视情况而定，两个中较大者。

同时，两个形状元件中的较长者视为参考元件。

若两个形状元件的额定尺寸相同，则每个都可以作为参考元件。

若出于功能原因不允许这样定义参考元件，则必须标注DIN ISO1101平行度公差。

3 Thread tolerances3 螺纹公差The following thread tolerances shall apply unless there are other requirements specified in the individual product standards (dimensional standards) or in the purchase order documents.除非产品标准（尺寸标准）或订购文件中另有规定，否则则适用于下列螺纹公差。

3.1 Product grades A and B3.1 产品等级A和BMetric as specified in DIN 13: tolerance quality medium (m);DIN 13中规定的公制：公差质量中等（m）；thread engagement group N complying with DIN 13 Part 14.符合DIN 13的第14部分的螺纹组N。

Tolerance classes for commercial bolts, screws and nuts shall comply with DIN 13 Part 14.商用螺栓、螺钉和螺母的公差等级应符合DIN 13的第14部分。

Table 1表11)Thread tolerances for electroplated bolts, screws and nuts shall comply with DIN 267 Part 9.电镀螺栓、螺钉和螺母的螺纹公差应符合DIN 267的第9部分。

Thread tolerances for hot dip galvanized bolts, screws and nuts shall comply with DIN 267 Part 10.热镀锌螺栓、螺钉和螺母的螺纹公差应符合DIN 267的第10部分。

序号德国标准中文品名英文品名国际标准中国标准Item DIN-Standard Description in Chinese Description in English ISO-Standard GB-Standard 1DIN1圆锥销taper pins ISO2339GB/T117-2000 2DIN7圆柱销parallel pins ISO2338GB/T119-2000 3DIN84开槽圆柱头螺钉slotted cheese head screws ISO1207GB/T65-2000 4DIN85开槽盘头螺钉slotted pan head screws ISO1580GB/T67-2000 5DIN93单耳止动垫圈tab washers ISO1580GB/T854-1998 6DIN94开口销split cotter pins ISO1234GB/T91-20007DIN95开槽半沉头木螺钉slotted raised csk head woodscrewsGB/T101-19868DIN96开槽半圆头木螺钉slotted round head wood screws GB/T99-19869DIN97开槽沉头木螺钉slotted countersunk head woodscrewsGB/T100-198610DIN125-A平垫plain washers ISO7089GB/T97.1-1985 11DIN125-B平垫(带倒角)mediun washers ISO7090GB/T97.2-1985 12DIN126平垫plain washers ISO709113DIN127-A重型弹垫spring lock washers,tang ends GB/T7244-1987 14DIN127-B标准弹垫spring lock washers,square ends GB/T93-1987 15DIN128-A鞍形弹垫single coil spring lock washers GB/T7245-1987 16DIN137-A弹簧止动垫圈curved spring washers17DIN137-B波形弹垫wave spring washers GB/T955-1987 18DIN186T型方颈螺栓T-head bolts with square neck GB/T37-1988 19DIN188T型双接头螺栓T-head bolts with double nip20DIN258螺纹圆锥销taper pins with threaded end ISO873721DIN261T型头螺栓T-head bolts22DIN315AF蝶型螺母(美制)wing nuts amercia form23DIN315DF蝶型螺母(德制)wing nuts germany form GB/T62-1988 24DIN316AF蝶型螺钉(美制)wing screws amercia form25DIN317DF蝶型螺钉(德制)wing screws germany form26DIN319圆球型盖型螺母ball knobs27DIN404开槽带孔球面圆柱头螺钉slotted capstan screws GB/T832-198828DIN417开槽长圆柱端紧定螺钉slotted set srews with full dogpointISO7435GB/T75-198529DIN427开槽平端紧定螺钉(半牙)slotted set srews with chamferedendISO2342GB/T73-198530DIN431小六角特薄细牙螺母pipe nuts with thread GB/T808-1988 31DIN432外舌止动垫圈external tap GB/T856-1988 32DIN433小垫圈(用于圆柱头螺钉)washers for cheese head screws ISO7092GB/T848-198533DIN434方斜垫圈(U型)square taper washers for U-sectionGB/T852-198834DIN435方斜垫圈(I型)square taper washers for I-sectionsGB/T852-198835DIN436方垫圈square washers序号德国标准中文品名英文品名国际标准中国标准Item DIN-Standard Description in Chinese Description in English ISO-Standard GB-Standard 36DIN438开槽凹端紧定螺钉slotted set with cup point ISO7436GB/T74-1985 37DIN439六角薄螺母hexagon thin nuts ISO4035GB/T6172-2000 38DIN439细牙六角薄螺母hexagon thin nuts ISO8675GB/T6173-200039DIN440木螺钉专用垫圈rounds washers for woodconstructionsISO709440DIN443密封帽sealing caps,push-in type41DIN444活节螺栓B 型eye bolts form B GB/T798-1988 42DIN462内舌止动垫圈internal tab washers43DIN463双耳止动垫圈washers with two taps GB/T855-1988 44DIN464滚花高头螺钉knurled thumb screws with collar GB/T834-198845DIN465开槽滚花高头螺钉slotted knurled thumb screws with collar46DIN466滚花高螺母knurled thumb nuts with collar GB/T806-1988 47DIN467滚花薄螺母knurled thumb thin nuts GB/T807-1988 48DIN470锁紧垫圈sealing washers49DIN471轴用弹性挡圈retaining rings forshafts(external),circlipsGB/T894.1-198650DIN472孔用弹性挡圈retaining rings forbores(internal),circlipsGB/T893.1-198651DIN478方头带垫螺栓square head bolts with collar52DIN479方头圆柱底端螺栓square head bolts with half dog point53DIN480方头带垫半圆底端螺栓square head bolts withcollar,half dog point and rounded54DIN508T型槽螺母T-slot nuts ISO29955DIN525单头螺柱single end studs56DIN529地脚螺栓masonry bolts GB/T799-1988 57DIN546带槽圆螺母slotted round nuts GB/T817-198858DIN547端面带孔圆螺母round nuts with drilled holes inone faceGB/T815-198859DIN551开槽平端紧定螺钉slotted sit screws with flatpointISO4776GB/T73-198560DIN553开槽锥端紧定螺钉slotted set screws with conepointISO7434GB/T71-198561DIN555六角螺母hexagon nuts ISO403462DIN557方螺母-C square nuts GB/T39-1988 63DIN558六角头螺钉hexagon screws ISO401864DIN561六角头圆柱端紧定螺钉hexagon set screws with full dog point65DIN562薄型方螺母-B square nuts without bevel(pressed nuts)66DIN571六角头木螺钉hexagon head wood screws (coachscrews)GB/T102-198667DIN580吊环螺钉lifting eye bolts ISO3266GB/T825-1988 68DIN582吊环螺母lifting eye nuts69DIN601六角头螺栓hexagon bolts ISO4016序号德国标准中文品名英文品名国际标准中国标准Item DIN-Standard Description in Chinese Description in English ISO-Standard GB-Standard70DIN603大半圆头方颈螺栓(马车螺栓)mushroom head square neck bolts(carriage bolts)ISO8677GB/T14-198871DIN604沉头带插销马车螺栓flat countersunk nib bolts72DIN605沉头长方颈马车螺栓flat countersunk long square neck bolts73DIN607半圆头带插销马车螺栓cup head nib bolts74DIN608沉头短方颈马车螺栓flat countersunk short square neck bolts75DIN609六角头精配螺栓（长螺纹）hexagon fitted bolts,long thread76DIN610六角头精配螺栓（短螺纹）hexagon fitted bolts,short thread77DIN653滚花平头螺钉knurled thumb screws thin type GB/T835-1988 78DIN660半圆头铆钉round head rivets ISO1051GB/T867-1986 79DIN661沉头铆钉contersunk head rivets ISO1051GB/T869-1986 80DIN662半沉头铆钉raised contersunk head rivets ISO105181DIN674大扁头铆钉mushroom head rivets ISO105182DIN703重型侧面带孔圆螺母adjusting rings,heavy range (shafting collars)83DIN705侧面带孔圆螺母adjusting rings,light range(shafting collars)GB/T816-198884DIN741卡头wire rope clips85DIN787T型槽螺钉T-slot screws ISO29986DIN835双头螺柱（牙长=2D）studs-metal (end=2d)GB/T900-198887DIN906内六角锥型闭锁螺钉hexagon socket pipe plugs,conical thread88DIN908内六角直型闭锁螺钉hexagon socket screw plugs,cyl. thread89DIN909外六角锥型闭锁螺钉hexagon head pipe plugs,conical thread90DIN910外六角直型闭锁螺钉hexagon head screw plugs,cyl.thread91DIN911内六角扳手socket wrenches ISO293692DIN912内六角圆柱头螺钉hexagon socket cap screws ISO4762GB/T70-200093DIN913内六角平端紧定螺钉hexagon socket set screws withflat pointISO4026GB/T77-200094DIN914内六角尖端紧定螺钉hexagon socket set screws withcone pointISO4027GB/T78-200095DIN915内六角圆柱端紧定螺钉hexagon socket set screws withdog pointISO4028GB/T79-200096DIN916内六角凹端紧定螺钉hexagon socket set screws withcup pointISO4029GB/T80-200097DIN917薄型盲螺母hexagon cap nuts98DIN920开槽小圆柱头螺钉slotted short cheese head screws99DIN921开槽大圆柱头螺钉slotted large cheese head screws GB/T838-1988100DIN923开槽圆柱头轴肩螺钉slotted pan head screws withshoulderGB/T830-1988101DIN927开槽无头轴肩螺钉slotted shoulder screws102DIN928焊接方螺母square weld nuts GB/T13680-1992 103DIN929焊接六角螺母hexagon weld nuts GB/T13681-1992序号德国标准中文品名英文品名国际标准中国标准Item DIN-Standard Description in Chinese Description in English ISO-Standard GB-Standard 104DIN931六角头螺栓（半牙）hexagon head screws ISO4014GB/T5782-2000 105DIN933六角头螺栓（全牙）hexagon head screws ISO4017GB/T5783-2000 106DIN934六角头螺母(1型)hexagon full nuts ISO4032GB/T6170-2000 107DIN934细牙六角头螺母(1型)hexagon full nuts ISO8673GB/T6171-2000 108DIN935开槽六角螺母hexagon slotted and castle nuts ISO7035GB/T6178-1986 109DIN936六角头薄螺母hexagon thin nuts ISO4035GB/T6172.1-2000110DIN937六角头开槽薄螺母hexagon thin slotted and castlenutsISO7038GB/T6181-1986111DIN938双头螺柱（牙长=1D）studs metal (end=1d)GB/T897-1988 112DIN939双头螺柱（牙长=1.25D）studs metal (end=1.25d)GB/T898-1988 113DIN940双头螺柱（牙长=1.5D）studs metal (end=1.5d)114DIN960六角头细牙螺栓（半牙）hexagon head bolts,metric finepitch threadISO8765GB/T5785-2000115DIN961六角头细牙螺栓（全牙）hexagon head bolts,metric finepitch threadISO8676GB/T5786-2000116DIN962头部穿孔六角头螺栓additional shapes and versions for bolts117DIN963开槽沉头螺钉slotted countersund head screws ISO 2009GB/T68-2000118DIN964开槽半沉头螺钉slotted raised countersunk ovalhead screwsISO 2010GB/T69-2000119DIN965十字槽沉头螺钉cross recessed countersunk headscrewsISO7046GB/T819.1-2000GB/T819.2-1997120DIN966十字槽半沉头螺钉cross recessed raised countersunkhead screwsISO7047GB/T820-2000121DIN970六角头螺母hexagon nuts type-1122DIN971六角头螺母hexagon nuts type-2123DIN972细牙六角头螺母(2型)hexagon nuts with fine thread ISO8674GB/T6176-2000 124DIN975牙条(全螺纹)threaded rods(studdings)GB/T15389-94 125DIN976螺纹销threaded pins(stud bolts)126DIN979六角头开槽薄螺母（2型）hexagon thin slotted and castle nuts127DIN980全金属六角锁紧螺母（1型）prevailling torque type hexagonnuts,all metall nutsISO7199GB/T6184-2000128DIN981圆螺母locknuts ISO2982GB/T812-1988129DIN982六角头尼龙锁紧螺母prevailling torque type hexagonnuts,heavy type ,with nylonISO7040GB/T889.1-2000130DIN985六角头薄型尼龙锁紧螺母prevailling torque type hexagonnuts,heavy type ,with nylonISO10511GB/T6172.2-2000131DIN986六角盖型尼龙锁紧螺母prevailling torque typedomed capnuts with nylon insert132DIN988配合垫片shim rings133DIN1052木材连接用垫片washers for timber connectors 134DIN1151沉头钢钉round plain head nails135DIN1440销钉专用垫片A型plain washers for clevis pins(A型)ISO8738136DIN1441销钉专用垫片plain washers for clevis pins137DIN1444带头销钉clevis pins with head ISO2341序号德国标准中文品名英文品名国际标准中国标准Item DIN-Standard Description in Chinese Description in English ISO-Standard GB-Standard 138DIN1471圆锥型槽销grooved pins,taper grooved ISO8744GB/T13829.2-92139DIN1472圆锥型槽销(半槽)grooved pins,taper grooved halflengthISO8745GB/T13829.2-92140DIN1473平行槽销(带倒角)grooved pins,parallel groovedfull lengthISO8740141DIN1474前端凹槽槽销grooved pins,reserve grooved halflengthISO8741142DIN1475中部凹槽槽销grooved pins,centre grooved ISO8742143DIN1476圆头槽销grooved pins with round head ISO8746GB/T13829.3-92144DIN1477沉头槽销grooved pins with countersunkheadISO8747145DIN1479六角螺母棒turnuckles(centre parts),made out of hexagon bar146DIN1480花篮螺栓turnuckles with eye bolt and hook bolt147DIN1481弹性圆柱销spring pins,heavy type ISO8752GB/T879-1986 148DIN1587组合式盖型螺母hexagon domed cap nuts GB/T802-1988149DIN1804开槽圆螺母（配合沟头扳手）slotted round nuts for hook spanner150DIN1816圆螺母（带插销孔）round nuts with set holes151DIN2093盘型弹簧垫圈disc springs152DIN3017喉箍hose clamps153DIN3404润滑油嘴（旋扭头）lubricating nipples,button head154DIN3567管夹shackles for conduilts155DIN3570U型螺栓stirrup bolts(U-bolts)156DIN6319球面垫圈spherical washers,conical seats GB/T849-1988 157DIN6325圆柱销parallel pins ISO8734158DIN6330厚六角螺母hexagon nuts ,1.5d GB/T56-1988 159DIN6331厚六角法兰面螺母hexagon nuts ,1.5d with collar GB/T6177-1986 160DIN6334长六角螺母hexagon nuts ,3d161DIN6797-A外齿锁紧垫圈external teeth lock washers GB/T862.1-1987 162DIN6797-I内齿锁紧垫圈internal teeth lock washers GB/T861.1-1987163DIN6798-A外锯齿锁紧垫圈external teeth serrated lockwashersGB/T862.2-1987164DIN6798-I内锯齿锁紧垫圈internal teeth serrated lockwashersGB/T861.2-1987165DIN6799 开口挡圈retaining rings for shafts(E-rings),circlipsGB/T896-1986166DIN6885平键（A型）parallel keys(form A )ISO773/2491167DIN6888半圆键woodruff keys ISO3912168DIN6899嵌环（支撑环）thimbles169DIN6900机器螺钉和垫圈组合件screws and washers assemblies GB/T9074.1-2002170DIN6901自攻螺钉和垫圈组合件tapping screws and washersassembliesGB/T9074.18-1998171DIN6912薄型带孔内六角圆柱头螺钉hexagon socket head cap screws with hole,low head序号德国标准中文品名英文品名国际标准中国标准Item DIN-Standard Description in Chinese Description in English ISO-Standard GB-Standard172DIN6914大六角头螺栓hexagon head bolts with large head(friction grip bolts)173DIN6915大六角螺母hexagon nuts with large wideth across flat(friction grip nuts)174DIN6916大垫圈round washers for friction grip bolts175DIN6917楔型方垫圈spuare taper washers forfriction grip bolts on T-sections176DIN6923六角法兰面螺母hexagon flange nuts ISO4161GB/T6177-2000177DIN6925全金属六角锁紧螺母(2型）prevailing torque type hexagonnuts,all metallic nutsISO7042GB/T6185.1-2000178DIN7337开口型抽芯铆钉（沉头、扁圆头）blind rivets GB/T12617/12618-1990179DIN7338扁平头半空心/全空心铆钉rivets for brake and clutchliningGB/T875/975-1986180DIN7343螺旋夹紧销spiral pins ISO8750 181DIN7346轻型弹性圆柱销spring pins,light type ISO13337182DIN7349重型弹性圆柱销用垫圈washers for bolts with heavy type spring pinss183DIN7500ISO公制螺纹螺钉(多种头型)threadforming screws for ISO-metric thread184DIN7504自攻自钻螺钉(多种头型)self-drilling tapping screws 185DIN7513开槽切削螺纹螺钉(多种头型)thread cutting screws186DIN7516十字槽切削螺纹螺钉(多种头型)thread cutting screws cross recess187DIN7965T型四爪螺母tee nuts with pronge188DIN7968钢结构用六角头螺栓连接副hexagon head fitted bolts forsteel structuresGB/T1228/1229/1230-2006189DIN7971开槽盘头自攻螺钉pan head tapping screws with slot ISO1481GB/T5282-1985190DIN7972开槽沉头自攻螺钉countersunk flat head tappingscrews with slotISO1482GB/T5283-1985191DIN7973开槽半沉头自攻螺钉raised countersunk oval headtapping screws with slotISO1483GB/T5284-1985192DIN7976六角头自攻螺钉hexagon tapping screws ISO1479GB/T5285-1985193DIN7980圆柱头螺钉用弹簧垫圈spring lock washers for screwswith cylindrical headsISO8738194DIN7981十字槽盘头自攻螺钉pan head tapping screws withcross recessedISO 7049GB/T845-1985195DIN7982十字槽沉头自攻螺钉countersunk flat head tappingscrews with cross recessedISO7050GB/T846-1985196DIN7983十字槽半沉头自攻螺钉raised countersunk oval headtapping screws with crossISO7051GB/T847-1986197DIN7984薄型内六角圆柱头螺钉hexagon socket head cap screws with，reduced head198DIN7985十字槽盘头螺钉pan head screws with crossrecessedISO7045GB/T818-2000199DIN7989钢结构用垫圈washers for steel structures GB/T1230-2006200DIN7990钢结构用六角头螺栓hexagon head bolts for steelstructuresGB/T1229-2006201DIN7991内六角沉头螺钉hexagon socket countersunk headscrewsISO10642202DIN7993轴用钢丝挡圈roundwire snap rings for shafts GB/T895.2-1986203DIN7995十字槽半沉头木螺钉cross recessed raised countersunkhead wood screwsGB/T952-1986204DIN7996十字槽圆头木螺钉cross recessed round head woodscrewsGB/T950-1986205DIN7997十字槽沉头木螺钉cross recessed countersunk headwood screwsGB/T951-1986序号德国标准中文品名英文品名国际标准中国标准Item DIN-Standard Description in Chinese Description in English ISO-Standard GB-Standard206DIN8140螺纹护套（普通\自锁等）ciol inserts,coarse,fine thread,silf locking207DIN9021大外径垫圈washers,outside diameter appro.3d ISO7093GB/T96-1985 208DIN11024弹簧卡子spring cotter for a bolt209DIN13257平板螺栓belting bolts (elevator bolts)210DIN18182干壁钉（墙板钉）dry wall screws211DIN28129环型螺母lifting nuts(eye nuts)GB/T63-1988212DIN70952圆螺母用止退垫圈tab washers for slotted roundnutsGB/T858-1988。