各种铆钉的英文翻译

各种螺钉的英文名称是什么？十字槽盘头组合机丝牙螺钉 Cross recessed pan head Combination screws十字槽盘头机丝牙螺钉 Cross recessed pan head screws十字槽伞头机丝牙螺钉 Cross recessed truss head screw十字槽伞头三角牙螺钉 Cross recessed truss head triangular screw十字槽沉头机丝牙螺钉 Cross recessed countersunk head screw十字槽沉头三角牙螺钉 Cross recessed countersunk head triangular screw十字槽沉头自攻牙螺钉 Cross recessed countersunk head tapping screws十字槽沉头机丝牙螺钉 Cross recessed countersunk head十字槽介子头螺钉 ross recessed truss head screw外六角三角牙螺钉 hexagon head triangular screw十字槽圆头机丝牙螺钉 cross recessed round head screw手拧螺丝(拇指螺丝) thumb screw圆锥销 Taper pins圆柱销 Parallel pins开槽圆柱头螺钉 Slotted cheese head screws开槽盘头螺钉 Slotted pan head screws单耳止动垫圈 Tab washers开口销 Split cooter pins开槽半沉头木螺钉 Slotted raised csk head wood screws 开槽半圆头木螺钉 Slotted round head wood screws开槽沉头木螺钉 Slotted countersunk head wood screws 平垫 Plain washers平垫（带倒角） Mediun washers平垫 Plain washers重型弹垫 Spring lock washers,tang ends标准弹垫 Spring lock washers,square ends鞍形弹垫 Single coil spring lock washers弹簧止动垫圈 Curved spring washers波形弹垫 Wave spring washersT型方颈螺栓 T-head blots with square neckT型双接头螺栓 T-head bolts with double nip螺纹圆锥销 Taper pins with threaded endT型头螺栓 T-head bolts蝶型螺母（美制） Wing nuts America form蝶型螺母（德制） Wing nuts germany form蝶型螺母（美制） Wing screws America form蝶型螺母（德制） Wing screws germany form圆球型盖型螺母 Ball knobs开槽带孔球面圆柱头蚴钉 Slotted capstan screws开槽长圆柱端紧定螺钉 Slotted set srews with full dog point开槽平端紧定螺钉（半牙） Slotted set srews with chamfered end 小六角特薄细牙螺母 Pip nuts with thread外舌止动垫圈 External tap小垫圈(用于圆柱头螺钉) Washers for cheese head screws方斜垫圈（U型） Square taper washers forU-section方斜垫圈（I型） Square taper washers forI-sections方垫圈 Square washers开槽凹端紧定螺钉 Slotted set with cup point六角薄螺母 Hexagon thin nuts细牙六角薄螺母 Hexagon thin nuts木螺钉专用垫圈 Rounds washers for wood constructions密封帽 Sealing caps,push-in type活节螺栓B型 Eye bolts form B内舌止动垫圈 Internal tab washers双耳止动垫圈 Washers with two taps滚花高头螺钉 Knur led thumb screws with collar开槽滚花高头螺钉 Slotted knurled thumb screws with collar 滚花高螺母 Knurled thumb nuts with collar滚花薄螺母 Knurled thumb thin nuts锁紧垫圈 Sealing washers轴用弹性垫圈 Retaining rings for shafts(external),circlips 孔用弹性垫圈 Retaining rings for bores(internal),circlips 方头带垫螺栓 Square head bolts with collar方头圆柱底端螺栓 Square head bolts with half dog point方头带垫关圆底端螺栓 Square head bolts with collar,half dog pointT型槽螺母 T-slot nuts单头螺柱 Single end studs地脚螺栓 Masonry bolts带槽圆螺母 Slotted round nuts端面带孔圆螺母 Round nuts with drilled holes in one face 开槽平端紧定螺钉 Slotted set screws with flat point开槽锥端紧定螺钉 Slotted set screws with cone point六角螺母 Hexagon nuts方螺母-C Square nuts六角头螺钉 Hexagon screws六角头圆柱端紧定螺钉 Hexagon set screws with full dog point薄型方螺母-B Square nuts without bevel(pressed nuts)六角头木螺钉 Hexgon head wood screw(coach screws)吊环螺钉 Lifting eye bolts吊环螺母 Lifting eye nuts圆锥型槽销 Grooved pins,taper grooved圆锥型槽销（半槽） Grooved pins,taper grooved half length平行槽销（带倒角） Grooved pins,parallel grooved full length前端凹槽槽销 Grooved pins,reverve grooved half length中部凹槽槽销 Grooved pins,center grooved圆头槽销 Grooved pins with round head沉头槽销 Grooved pins with countersunk head六角螺母棒 Turnuckles(center parts),made out of hexagon bar花蓝螺栓 Turnuckles with eye bolt and hook bolt弹性圆柱销 Spring pins,heavy type组合式盖型螺母 Hexagon domed cap nuts开槽圆螺母(配合沟头扳手) Slotted round nuts for hook spammer圆螺母（带插销孔） Round nuts with set holes盘型弹簧垫圈 Disc springs喉箍 Hose clamps润滑油嘴（旋扭头） Lubricating nipples,button head管夹 Shackles for conduiltsU型螺栓 Stirrup bolts(U-bolts)球面垫圈 Spherical washers,conical seats圆柱销 Parallel pins厚六角螺母 Hexagon nuts,1.5d厚六角法兰面螺母 Hexagon nuts,1.5d with collar长六角螺母 Hexagon nuts,3d外齿锁紧垫圈 External teeth lock washers内齿锁紧垫圈 Internal teeth lock washers外锯齿锁紧垫圈 External teeth serrated lock washers内锯齿锁紧垫圈 Internal teeth serrated lock washers开口挡圈 Retaining rings for shafts(E-rings),circlips平键（A型） Parallel keys(form A)半圆键 Woodruff keys嵌环（支撑环） Thimbles机器螺钉和垫圈组合件 Screws and washers assemblies自攻螺钉和垫圈组合件 Tapping screws and washer assemblies薄型带孔内六角圆柱螺钉 Hexagon cocket head cap screws with hole,low head 大六角头螺栓 Hexagon head bolts with large head(friction grip nolts)大六角螺母 Hexagon nuts with large wideth across flat(friction grip nuts)大垫圈 Round washers for friction grip bolts楔型方垫圈 Spuare taper washers for friction grip bolts on T-六角法兰面螺母 Hexagon flange nuts全金属六角锁紧螺母（2型） Prevailing torque type hexagon nuts,all metallic nuts轻型弹性圆柱销 Spring pins,light type重型弹性圆柱销用垫圈 Washers for bolts with heavy type spring pinssISO公制螺纹螺钉（多种头型） Thread forming screws for ISO-metric thread 自攻自钻螺钉（多种头型） Self-drilling tapping screws开槽切削螺纹螺钉（多种头型） Thread cutting screws十字槽切削螺纹螺钉（多种头型） Thread cutting screws cross recessT型四爪螺母 Tee nuts with pronge钢结构用六角头螺栓连接副 Hexagon head fitted bolts for steel structures 开槽盘头自攻螺钉 Pan head tapping screws with slot开槽沉头自攻螺钉 countersunk flat head tapping screws with slot开槽半沉头自攻螺钉 Raised sountersunk oval head tapping screws with slot六角头自攻螺钉 Hexagon tapping screws圆柱头螺钉用弹簧垫圈 Spring lock washers for screws with cylindrical heads十字槽盘头自攻螺攻 Pan head tapping screws with cross recessed十字槽沉头自攻螺攻 Countersunk flat head tapping screws with cross recessed十字槽半沉头自攻螺攻 Raised countersunk oval head tapping screws with cross薄型内六角圆柱头螺钉 Hexagon socket head cap screws with,reduced head十字槽盘头螺钉 Pan head screws with cross recessed钢结构用垫圈 Washers for steel structures钢结构用六角头螺栓 Hexagon head bolts for steel structures内六角沉头螺钉 Hexagon socket coutersunk head screws轴用钢丝挡圈 Roundwire snap rings for shafts十字槽半沉头木螺钉 Cross recessed raised countersunk head wood screws十字槽圆头木螺钉 Cross recessed round head wood screws十字槽沉头木螺钉 Cross recessed countersunk head wood screws螺纹护套(普通、自锁等) Ciol inserts,coarse,fine thread,silf locking大外径垫圈 Washers,outside diameter appro.3d弹簧卡子 sping cotter for a bolt平板螺栓 Belting bolts(elevator bolts)干壁钉（墙板钉） Dry wall screws环型螺母 Lifting nuts(eye nuts)圆螺母用止退垫圈 Tab washer for slotted round nuts。

各种铆钉的英文翻译铆钉种类Open End Blind Rivet 开口型抽芯铆钉Closed End Blind Rivet 封闭型抽芯铆钉Multi-grip Rivet 双鼓型抽芯铆钉Peel Type Blind Rivet 拉花型抽芯铆钉Drive Rivet 击芯铆钉Grooved Type Blind Rivet 沟槽型抽芯铆钉Ring-Grooved Lockbolt 环槽铆钉Maolock 拉丝铆钉Insert Nut 铆螺母Plastic Rivets 塑料铆钉Open Type Blind Rivets 开口型抽芯铆钉Alu/Steel Standard 铝/钢标准型Alu/Steel Countersunk 铝/钢沉头型Alu/Steel Large Flange 铝/钢大帽型Alu/Stainless Steel Standard 铝/不锈钢标准型Alu/Stainless Steel Countersunk 铝/不锈钢沉头型Alu/Stainless Steel Large Flange 铝/不锈钢大帽型Alu/Alu Standard 铝/铝标准型Alu/Alu Countersunk 铝/铝沉头型Alu/Alu Large Flange 铝/铝大帽型Copper/Steel Standard 铜/钢标准型Copper/Steel Countersunk 铜/钢沉头型Copper/Stainless Steel Standard 铜/不锈钢标准型Copper/Stainless Steel Countersunk 铜/不锈钢沉头型Steel/Steel Standard 钢/钢标准型Steel/Steel Countersunk 钢/钢沉头型Steel/Steel Large Flange 钢/钢大帽型Stainless Steel/Steel Standard 不锈钢/钢标准型Stainless Steel/Steel Countersunk 不锈钢/钢沉头型Stainless Steel/Stainless Steel Standard 不锈钢/不锈钢标准型Stainless Steel/Stainless Steel Countersunk 不锈钢/不锈钢沉头型Seald Type Blind Rivets 封闭型抽芯铆钉Alu/Steel Standard 铝/钢标准型Alu/Steel Countersunk 铝/钢沉头型Alu/Stainless Steel Standard 铝/不锈钢标准型Alu/Stainless Steel Countersunk 铝/不锈钢沉头型Alu/Alu Standard 铝/铝标准型Alu/Alu Countersunk 铝/铝沉头型Copper/Steel Standard 铜/钢标准型Copper/Stainless Steel Standard 铜/不锈钢标准型Steel/Steel Standard 钢/钢标准型Stainless Steel/Stainless Steel Standard 不锈钢/不锈钢标准型Multigrip Type Blind Rivets 双鼓型抽芯铆钉Alu/Steel Standard 铝/钢标准型Alu/Steel Large Flange 铝/钢大帽型Alu/Stainless Steel Standard 铝/不锈钢标准型Alu/Stainless Steel Large Flange 铝/不锈钢大帽型Steel/Steel Standard 钢/钢标准型Steel/Steel Large Flange 钢/钢大帽型Stainless Steel/Stainless Steel Standard 不锈钢/不锈钢标准型Stainless Steel/Stainless Steel Large Flange 不锈钢/不锈钢大帽型Anlock Type Blind Rivets 拉丝型抽芯铆钉Alu/Steel Dome Head 铝/钢圆头型Alu/Steel Countersunk 铝/钢沉头型Alu/Alu Dome Head 铝/铝圆头型Alu/Alu Countersunk 铝/铝沉头型Steel/Steel Flat Head 铜/钢圆头型Steel/Steel Countersunk 钢/钢沉头型Stainless Stee/Stainless Stee Dome Head 不锈钢/不锈钢圆头型Fold Type Blind Rivets 抽折式抽芯铆钉Alu/Steel Dome Head 铝/钢圆头型Alu/Alu Dome Head 铝/铝圆头型Steel/Steel Dome Head 钢/钢沉头型Stainless Steel/Steel Dome Head 不锈钢/钢圆头型Stainless Steel/Stainless Steel Dome Head 不锈钢/不锈钢圆头型Peel Type Blind Rivets 拉花型抽芯铆钉Steel/Steel Standard 钢/钢标准型Grooved Type Blind Rivets 沟槽型抽芯铆钉Alu/Steel Standard 铝/钢标准型Drive Rivets 击芯铆钉Alu/Steel Standard 铝/钢标准型Alu/Steel Large Flange 铝/钢大帽型Steel/Steel Standard 钢/钢标准型Steel/Steel Large Flange 钢/钢大帽型Ring-Grooved Lockbolt 环槽型抽芯铆钉Alu Standard 铝标准型Alu Countersunk 铝沉头型Steel Standard 钢标准型Steel Countersunk 钢沉头型Stainless Steel Standard 不锈钢标准型Stainless Steel Countersunk 不锈钢沉头型Blind Rivet Nuts 抽芯铆螺母Alu Standard 铝标准型Alu Countersunk 铝沉头型Alu Small Head 铝小头型Steel Standard 钢标准型Steel Countersunk 钢沉头型Steel Small Head 钢小头型Stainless Steel Dome Head 不锈钢圆头型Stainless Steel Countersunk 不锈钢沉头型Stainless Steel Small Head 不锈钢小头型raised-head rivet 凸头铆钉blind rivet 盲铆钉空心铆钉Pulling Rivet拉铆钉Countersunk rivet 埋头铆钉沉头铆钉Riveting Tool Rivets 铆接工具。

紧固件-中英文对照No. 英文单词简写中文1 screw scr 螺丝2 nut nut 螺母3 washer wash 垫圈4 head hd 头5 thread thre 螺纹6 coating coat 镀层7 rivet riv 铆钉8 standoff stdoff 内外六角钉9 driver driv 穴10 hexagon hexa 六角11 tooth tooth 齿12 lock lck 锁13 spring spr 弹簧14 wave wave 波浪型15 pitch pitch 牙距16 partial thread PT 半螺纹17 PT PT 一种螺纹形式18 Full Thread FT 全螺纹19 silver silv 银20 cone cone 锥形21 Eco-syn Eco 30度牙的一种螺纹22 Thread Forming TF 自攻螺纹23 Self Tapping self tapp 自切屑螺纹24 pin pin 销25 shaft Shaf 轴26 steel St 铁27 stainless steel SS 不锈钢28 Brass(Cu) Bras(Cu) 铜29 Aluminum AL 铝30 Rubber Rub 橡胶31 machine screw mech scr 机制螺丝32 SEM screw SEM Scr 组合螺丝33 Material material 材料34 Grade GD 等级35 Finish Finish 表面处理36 Point Point 点37 Clamp Clam 夹子38 internal Int 内39 external ext 外40 thickness / 厚度41 length / 长度42 hole / 孔43 Metric Metcric 公制44 DIN / 德标45 ANSI / 美标46 JIS / 日标螺丝相关参数英语对照A: Machine Screw: 机械螺丝B: Tapping Screw: 自攻螺丝(分使用于金属与使用于塑料二种)B-1: Sheet Metal Tapping Screw. (铁板牙自攻螺丝)B-2: Plastic Tapping Screw. ( 塑料用, 自攻螺丝)C: Wooden Screw : 木工螺丝D: Drywall Screw : 水泥墙螺丝常见螺丝材质:a.Low Carbon Steel :低碳钢b. SS-304 : Stainless Steel 304c. SS-302: Stainless Steel 302 :结构韧性较好d. Aluminum 5052 :铝合金5052d. Brass: 黄铜e. Bronze: 青铜f. UNS C11000 Copper: 锑铜Finish Code: 外观处理规格Head Code: 头部外型螺丝型号Drive Code: 头部剖沟,特征型号Length Code: 螺丝长度(mm)A-1: Thread Code: 螺丝型号A-2: Length Code: 螺丝长度:A-3: Drive Code/ 头部剖沟,特征.a. Slotted: 一字( Minus )b. Phillips: 十字( Plus )c. Phil-Slot: 一字/十字d. Hex Scoket: 内六角e. One Way: 单向(只可锁入,不可退出) A-4: Head Code/ 头部外型.a. Flat: 平头(锁入后,顶部与工作件齐平)b. Oval: 色拉头c. Round: 圆头d. Pan: 圆扁头e. Truss: 大圆扁头f. Hex : 六角头A-5: Finish Code/ 外观处理.a. Z: Zine-Plated: 镀锌b. Ni: Ni-Plated: 镀镍c. Tin-Plated: 镀锡d. Zine Plated / Green Iridite: 镀锌绿膜处理.e. Radiant Plated: 镀五彩f. Passivate: 抗氧化处理.g. Alodial Finish: 无外观处理螺纹大径：Major Diam螺纹中径：Pitch diam螺纹底径：Minor diam通止规：Go/No go gage机械性能：mechanical and physical propertiesunified thread 统一英制螺纹Lustrate hydrogen after galvanizing to avoid hydrogen embrittlement 镀后去氢，防止氢脆Case carburization 表面渗碳With across flats 对边With across corners 对角Radius of fillet:头下圆角Transition thread length 过度螺纹Wrenching height 扳拧高度Rockwell 铬氏硬度Vickers 维氏硬度Brinell 布氏硬度Metallography microscope 金相显微镜Salt spray device 盐雾试验箱Tensile testing machine 拉力试验机Cold forming 冷打Hot forging 红镦P C 8 = property class 8 机械性能8级原材料：Raw material球化退火：Annealing冷拔：Drawing冷镦：Forming机加工：Machining螺纹成型：Roll Threading热处理：heat-treatment表面处理：finish去氢：Lustrating hydrogen检验：Inspection包装：Packing入库：Stocking车床：lathe磨制：grinding红打：hot forging冲压：punchingDiameter 直径Length 长度各类紧固件标准件产品英语翻译对照插片壁虎Steel Ceiling Anchors内迫壁虎Drop in Anchors碳钢锤钉壁虎Steel Hit Anchors碳钢六角螺帽Steel Hex Coupling Nuts强力车修壁虎Wedge Anchors外迫壁虎Cut Anchors化学壁虎Chemical Anchors不锈钢重载胀栓Heavy Duty Expansion Anchors鱼眼壁虎企眼长螺帽Tie Wire Anchors锌合金打入式壁虎Hammer Drive Anchors弹簧螺帽Strut Nuts兰花夹系列Toggle Bolts (Spring Toggle & Gravity Toggle)门窗、地板专用壁虎Nylon Frame Anchors or Metalframe Anchors石膏板中空壁虎Hollow Wall Anchors套管式壁虎Sleeve Anchors打入式壁虎鱼形尼龙壁虎Nylon Frame Harmmer Fixing (Nylon Hammer Drive Anchors)强力式锤钉壁虎Hit Anchors电梯壁虎Bolt Anchors重载壁虎Heavy duty anchors两片夹Loxin Masonry Anchors定位螺栓Set Bolts长型兰花夹Short Strap Anchors工具棒Drop in Setting Tools象脚壁虎Elephant foot anchors水泥预埋件Concrete Insert翻边胀轴Drop in Anchor with Lip冲件Legs Drywall Anchors六角盖头螺帽Hex Cap Nuts六角锯齿螺帽Hex Serrated Nuts六角轮缘螺帽Hex Flange Nuts高脚螺帽Hex Coupling Nuts(High Nuts)圆螺帽Round Nuts四角螺帽Square Nuts管用螺帽Pipe Nuts轮壳螺帽Wheel Nuts蝶型螺帽Wing NutsU形螺帽U NutsT形螺帽T Nuts环首螺帽Eye Nuts齿形螺帽Kep Nuts齿花螺帽Clinch Nuts耐候钢六角重型螺帽Corten Steel Heavy Hex Nuts焊接螺帽Weld Nuts高张力螺帽Heigh Strength Nuts建业用螺帽Structural Nuts不锈钢螺帽Stainless Steel Nuts铜螺帽Brass Nuts铝螺帽Aluminum Nuts合金钢螺帽Alloy Steel Nuts重型车螺帽Heavy Duty Wheel Hub Nuts铁器焊接袋帽Acorn Cap Nuts金属预置扭矩式螺帽All-Metal Prevailing Torque Type Nuts壁虎螺帽Anchor Nuts大尺寸螺帽Big Size Nuts铁盖袋帽Closed End Acorn Nuts盘形华司螺帽Conical Washer Nuts铁盖+尼龙圈组合盖帽Din 986 Domed Cap Nuts突缘尼龙盖帽Flange Nylon Insert Lock Nuts平面华司螺帽Flat Waser Nuts六角割沟螺帽Hex Slotted Nut自锁螺帽Self-Locking Nuts制止螺帽Sliding NutsSln-自动防松螺帽Sln Self-Locking Nuts其它特殊螺帽Special Nuts弹簧螺帽Spring Nuts不锈钢突缘螺帽Stainless Steel Flange Nuts 不锈钢六角轮缘尼龙螺帽Stainless Steel Flange Nylon Insert Lock Nuts不锈钢六角重型螺帽Stainless Steel Heavy Hex Nuts不锈钢六角螺帽Stainless Steel Hex Nuts不锈钢尼龙嵌入螺帽Stainless Steel Nylon Insert Lock Nuts普通六角螺帽Hex Nuts六角重型螺帽Heavy Hex Nuts薄型螺帽Hex Jam Nuts尼龙嵌入防松螺帽Nylon Insert Lock Nuts机械螺丝用六角螺帽Hex Machine Screw Nut 六角螺丝(栓) Hex Head Cap Screws(Hex Bolts)六角机械螺丝Hex Head Machine Bolts六角木牙螺丝Hex Lag Bolts四角螺丝Square Head BoltsT头螺丝T Head Bolts马车螺丝Carriage Bolts环首螺丝Eye Bolts内六角孔螺丝Hex Socket Cap Screws固定螺丝Set Screws螺椿栓Stud Bolts螺旋椿Screw Studs轮壳螺栓Wheel Bolts翼形螺丝Wing Screws自攻螺丝Self Tapping Screws自削螺丝Thread Cutting Screws钻尾螺丝Self Drilling Screws机械螺丝Machine Screws木螺丝Wood Screws家具螺丝Furniture Screws塑板螺丝Chipboard Screws墙用螺丝Drywall Screws基础螺栓Foundation BoltsU型螺栓U Bolts勾头螺栓Hook Bolts套挂螺丝Toggle Bolts突缘螺丝Flange Bolts轨道螺栓(鱼尾螺丝) Track Bolts耐候钢螺丝Corten Steel Heavy Hex Bolts扭矩控制螺栓T.C.Bolts高张力螺栓High Strength Bolts剪力钉(焊接螺丝) Welding Studs螺丝附华司组合Screws And Washers Assembled(Sems)大尺寸螺栓Big Size Bolts不锈钢小螺丝Stainless Steel Sheet Metal Screws不锈钢大螺丝Stainless Steel Bolts铝螺丝Aluminum Screws合金钢螺丝Alloy Steel Screws电子螺丝Electronic Screws微小精密螺丝Micro Screws塑料螺丝Plastic Screws复合材料用螺丝Particle Board Screws钛合金螺丝Titanium Alloy Bolts钛、锆、钼、铌等螺丝、零件、材料Ti,Zr,Mo,Nb Pare Metal Bolts Parts拇指螺丝Thumb Screws双头牙螺丝Double End Screws Hanger Bolt 车辆(汽车)螺丝、螺帽Automotive Fasteners 航天用螺丝Aerospace Fasteners飞机特殊扣件Source Control Bolts拉栓Blind Bolts面板螺丝Panel Fasteners电梯螺丝Elevator Bolts四角头固定螺丝Square Set Screws大头马车螺丝Step Bolts单向螺丝One Way Lag Screws管夹螺丝Hose Clamp Screws不锈钢固定螺丝Stainless Steel Hex Socket Cap Screws不锈钢内六角螺丝Stainless Steel Hex Socket Cap Screws铰链螺丝Hinge Screws货柜螺丝Container Screws复合材料钻尾螺丝Bi-Metal Self Drilling Screws三角牙螺丝Trilobular Thread Screws高低牙螺丝High Low Screws夹板用螺丝Particle Board Screws马桶螺丝Toilet Closet Bolts特长螺丝Special Longer Screws建业螺丝Building Fasteners不锈钢六角螺丝Stainless Steel Hex Socket Cap Screws其它特殊螺丝Special Screws Or Bolts不锈钢特殊螺丝Special Stainless Steel Screws宽牙螺丝（粗牙螺丝）Coarse Thread Screws 链带螺丝Collated Screws水泥螺丝Concrete Screws板模螺丝Construction Bolts锌蝶螺丝Die Cast Wing Screws; Zinc Alloy 重型车螺丝Heavy Duty Wheel Hub Bolts内六角固定螺丝Hex Socket Set Screws复合材料用螺丝（夹板用）Particle Board Screws犁壁螺丝Plow Bolts不锈钢木螺丝Stainless Steel Wood Screws 套挂螺栓及螺丝Toggle Bolts钛合金膨胀螺丝Titanium Alloy Expansion Bolts六角盖头螺帽Hex Cap Nuts六角锯齿螺帽Hex Serrated Nuts六角轮缘螺帽Hex Flange Nuts高脚螺帽Hex Coupling Nuts(High Nuts)圆螺帽Round Nuts四角螺帽Square Nuts管用螺帽Pipe Nuts轮壳螺帽Wheel Nuts蝶型螺帽Wing NutsU形螺帽U NutsT形螺帽T Nuts环首螺帽Eye Nuts齿形螺帽Kep Nuts齿花螺帽Clinch Nuts耐候钢六角重型螺帽Corten Steel Heavy Hex Nuts焊接螺帽Weld Nuts高张力螺帽Heigh Strength Nuts建业用螺帽Structural Nuts不锈钢螺帽Stainless Steel Nuts铜螺帽Brass Nuts铝螺帽Aluminum Nuts合金钢螺帽Alloy Steel Nuts重型车螺帽Heavy Duty Wheel Hub Nuts铁器焊接袋帽Acorn Cap Nuts金属预置扭矩式螺帽All-Metal Prevailing Torque Type Nuts壁虎螺帽Anchor Nuts大尺寸螺帽Big Size Nuts铁盖袋帽Closed End Acorn Nuts盘形华司螺帽Conical Washer Nuts铁盖+尼龙圈组合盖帽Din 986 Domed CapNuts突缘尼龙盖帽Flange Nylon Insert Lock Nuts平面华司螺帽Flat Waser Nuts六角割沟螺帽Hex Slotted Nut自锁螺帽Self-Locking Nuts制止螺帽Sliding NutsSln-自动防松螺帽Sln Self-Locking Nuts其它特殊螺帽Special Nuts弹簧螺帽Spring Nuts不锈钢突缘螺帽Stainless Steel Flange Nuts 不锈钢六角轮缘尼龙螺帽Stainless Steel Flange Nylon Insert Lock Nuts不锈钢六角重型螺帽Stainless Steel Heavy Hex Nuts不锈钢六角螺帽Stainless Steel Hex Nuts不锈钢尼龙嵌入螺帽Stainless Steel Nylon Insert Lock Nuts锌压属螺帽Zinc Die Casting Nuts普通六角螺帽Hex Nuts六角重型螺帽Heavy Hex Nuts薄型螺帽Hex Jam Nuts尼龙嵌入防松螺帽Nylon Insert Lock Nuts机械螺丝用六角螺帽Hex Machine Screw Nut合金钢线材盘元Alloy Steel Wire Rod球状化线材Annealing Wire And Rod黑铁丝Black Wire黄铜棒线Brass Wire And Rod磨光棒钢Bright Steel Bar(Hex/Round/Square)铜合金线Copper Alloy Wire线切割线 E.D.M Cutting Wire快削钢线材盘元Free Cutting Steel Wire Rod 线材Iron Or Steel Wire线材盘元Iron Or Steel Wire Rod洋白铜线Nickel Silver Wire磷青铜线Phosphate Bronze Wire不锈钢条棒Stainless Steel Bar(Round/Hex/Square)不锈钢冷锻线材Stainless Steel Cold Heading Wire不锈钢线(抽线后) Stainless Steel Draw Wire 不锈钢线材Stainless Steel Wire不锈钢线材及盘元Stainless Steel Wire And Rod棒钢Steel Bar(Hex/Round/Square)转回90度碾线头机90讧evolving Wire Twisting Machine气动拉钉机Air Riveter各式螺丝类产品自动包装Automatic Packaging For All Kinds Of Packaging自动包装机Automatic Packing Machine螺丝制造搓牙机械Automatic Thread Rolling Machine螺丝割尾加工机械Automatic Thread Slotting Machine螺丝制造成型机械Automatic Trimming Machine拉钉打头机Blind Rivet Heading Machine螺丝、螺帽成型机Bolt Formers,Nuts Formers,Headers螺丝、螺帽热处理Bolt Nut And Screws Heat Treatment螺丝、螺帽热处理炉Bolt Nut And Screws Heat Treatment Furnaces球状化电器炖炉Carburizing Furnace Vacuum And Bell Type Furnace超防锈复合瓷膜Ceramic Coating连续式光辉渗碳淬火炉Continuous Bright Carburizing Quenching Furnace连续式光辉调质淬火炉Continuous Bright Hardening Quenching Furnace中、高热镀锌光辉连续炉Continuous Bright Heat Treat Furnace连续式光辉热处理炉Continuous Type Bright Heat Treatment Furnace螺丝割尾及特殊割遘加工Machine Screw Shank Slotting螺丝钻孔加工Screw Shank Drilling鸡眼上下模Eyelets Dies一般线材、盘元、退火炉General Wire,Wire Rod,Annealing Furnace倒立式滑落型伸线机Handstand Type Wire Drawing Machine十字冲模Header Punches In Various Drives 成型冲模Header Punches In Various Drives 螺丝打头机Heading Machine螺丝制造高速搓牙机械High Speed Automatic Thread Rolling Machine高中低周波感应加热炉High,Medium,Low Frequency Induction Heater空心打头机Hollow Heading Machine热浸镀锌螺丝、螺帽Hot Dip Galvanizing Bolts And Nuts机械镀锌Mechanical Galvanized迷你成型机Mini-Formers成品自动收线机Non-Stop Coiler精抽自动收线机Non-Stop Coiler(Skinpass) 螺帽模Nut Forming Dies螺帽成型模Nuts Formers特殊零件成型机Parts Forming Maching冲模Punch Dies冲子Punch Pins罗拉成型机Rollers Formers机(踏)车用螺丝成型机Screw For Motorcycle Or Bicycle Heading Machine止付螺丝成型机Set Screws Formers套高成型机Sockets Formers一般线材、盘元、螺丝合金炖炉SpheroidizingBright Annealing Furnace球状化热处理炉Spheroidizing Heat Treatment Furnace攻牙机Tapping Machine螺丝攻、车刀、模具Taps Dies And Tools搓牙机铁屑分离装置Thread Chip Separator 滚牙轮Thread Rolling Dies牙板Thread Rolling Dies Plates精密油压滚牙机Hydraulic Thread Rolling Machines模具Tools六角整头模Trimming Dies Hexagan碳化钨模具Tungsten Carbide Die镀钛处理(Tin)专业加工服务Tin Hard Coating For Cutting Tools And Punch By Pvd电镀化学原料Various Electroplating Chemicals环规校正Calibration For Ring Gage环规、牙规、三线规校正Calibration For Ring Gage, Athread Gage, 3 Wire Gage螺丝、螺帽品检量测仪器Fasteners Inspection And Measurement Instruments螺丝、螺帽成型攻牙专用油Forming And Tapping Oils For Bolts And Nuts Formers螺丝、螺帽五金等检验Insptection Services For Fasteners And Hardware德国schatz扭力机代理Representative Of Schatz Torque MachinIso品质保证系统Iso Quality Assurance System生产管理系统Production Control System物料管理系统Material Control System齿轮Gears不锈钢牙条棒Stainless Steel Hread Rod马达轴承轴心组件Bearing Shaft(Motor)轴承轴心Bearing Shaft开口铆钉Blind Rivets长形拉帽Blind Rivet Nuts拉帽Blind Nuts拉钉Blind Rivets实心梢Clevis Pins And Straight Pins弹片Clips卷钉Coil Nails冷锻零件Cold Forming Part开口销Cotter PinsE型环E-Rings膨胀螺栓Expansion Anchor Bolts鸡眼钉Eyelets RivetsR型销Snap Pins闸、锁Latches And Keeper Assembleds其它特殊铆钉Other Specil Rivets销Pins格式管夹、管束Pipe Hanger铆钉Rivets螺旋锔及螺旋圈Screw Hook And Screw Rings中空钉Semi-Tubular Rivet开叉钉Split Drive Anchors弹簧华司Spring Washers弹簧蝴蝶夹Spring Wings不锈钢华司Stainlesssteel Washers钢铁钉Steel And Iron Nails搓牙铁钉Thread Nails钛合金铆钉Titaium Alloy Rivets管形铆钉Tubular Rivets华司Washers真空热处理Vacuum Heat Treatment螺丝、螺帽、五金、Diy扣件Fasteners合金钢工具Alloy Steel Tools螺栓模Bolt Heading Dies手动拉钉钳Hand Riveter船舶链Anchor Chain脚踏车链锁Bicycle Chain Locks螺丝起子Bit罗拉Chain Roller特殊铆合扣件Collars(A Blindfastener For Huck Intl)装饰链Decorative Chains自攻螺纹衬套Ensat Threaded Inserts六角扳手Hexagon Keys超音螺纹压入式螺纹自动锁扣Threaded Inserts For Plastic Injection Mouldeings汽车特殊杆接件Special Auto-Mobile Fastener As Your Needs螺纹护套Recoil Inserts链条用滚子Roller For Roller Chain金属板镶嵌组件及自动夹扣组件Sheet MetalFasteners工具套筒组件Socket Wrench Sets不锈钢链Stainless Steel Chains轭子T-Yoke轮胎链Tire Chains狗链Dog Chains喇叭头轭铁U-Yoke,T-Yoke For Speaker不锈钢输送带轮用轨道Stainless Wheel's Rack For Transporter工业用链Industrial Steel Link Chains拖链安全链Tow Chains And Safety Chains 机车离合器零件Manufacture Of Motorcycle's Cvt Parts牙条棒Thread Rod机(踏)车用螺丝、轴心Screws And Shafts For Motorcycle Or Bicycle针车用螺丝、轴心Screws And Shafts For Sewing Maching止付螺丝Socket Set Screws不锈钢宽牙螺丝Stainless Steel Coarse Thread Screws不锈钢高低牙螺丝Stainless Steel High-LowThread Screws不锈钢机械螺丝Stainless Steel Machine Screws不锈钢钻尾螺丝Stainless Steel Self Drilling Screws不锈钢自攻螺丝Stainless Steel Self Tapping Screws不锈钢自削螺丝Stainless Steel Thread Cutting Screws不锈钢三角牙螺丝Stainless Steel Tri-Lobular Thread Screws。

常用紧固件英语螺纹大径：Major Diam螺纹中径：Pitch diam螺纹底径：Minor diam通止规：Go/No go gage机械性能：mechanical and physical propertiesunified thread 统一英制螺纹Lustrate hydrogen after galvanizing to avoid hydrogen embrittlement 镀后去氢，防止氢脆Case carburization 表面渗碳With across flats 对边With across corners 对角Radius of fillet:头下圆角Transition thread length 过度螺纹Wrenching height 扳拧高度Rockwell 铬氏硬度Vickers 维氏硬度Brinell 布氏硬度Metallography microscope 金相显微镜Salt spray device 盐雾试验箱Tensile testing machine 拉力试验机Cold forming 冷打Hot forging 红镦P C 8 = property class 8 机械性能8级原材料：Raw material球化退火：Annealing冷拔：Drawing冷镦：Forming机加工：Machining螺纹成型：Roll Threading热处理：heat-treatment表面处理：finish去氢：Lustrating hydrogen检验：Inspection包装：Packing入库：Stocking车床：lathe磨制：grinding红打：hot forging冲压：punchingDiameter 直径Length 长度1 标准GB （国标）ISO(国际标准)DIN（德制）JIS（日标）ANSI /ASME （美标）BA （英制）2 螺纹M. MF (公制牙)UNC.UNF (美制牙)BSW.BSF (英制牙)3 海关编码73181500 螺栓73181600 螺帽73182100 垫圈BO=black oxide 氧化发黑IHH=ind hex head 锯六角头PH=phillips 十字槽sw/fw=split washer/flatwasher 弹垫平垫kep nut 锁紧螺母cementation 渗碳acorn nut 盖形螺母螺丝头型Pan 圆头(盘头)Oval 半沉头H.W.H.. 六角小法兰H.W.F. 六角大法兰CSK 沙拉头(沉头)Large wafer 大扁平头Bugle 喇叭头Truss 盘头带垫Pozi 米制槽Phill 十字槽Serra-tion 垫下带花Flower Head 开花头6-bobes recess 内梅花Piston bolt 活塞螺钉Winding bolt 线圈螺钉Hexagon head bolts-full thread 六角头螺栓全螺纹Carriage bolt 马车螺栓Square head bolt-product grade C 方头螺栓C级Flat counter sunk square neck bolts 沉头方颈螺栓Flat counter sunk nib bolts 沉头带榫螺栓Cup head square neck bolts 半圆头方螺栓Cup head nib bolts 半圆头带榫螺栓Cup head square neck bolts with large head –product grade C大半圆头方颈螺栓C级Hexagon head bolts-product grade C六角头螺栓C级Hexagon head bolts-full thread –product grade C 六角头螺栓全螺纹C级Hexagon head bolts 六角头螺栓Hexagon head bolts –full thread 六角头螺栓全螺纹Hexagon head bolts-reduced shank-product grade B六角头螺栓细杆菌B级Hexagon head bolts with fine pitch thread 六角头螺栓细牙Hexagon head bolts with fine pitch thread full thread六角头螺栓细牙全螺纹Hexagon flange bolts –heavy series-product grade B 六角法兰面螺栓加大系列车员B级Cross recessed pan head tapping screws 十字槽盘头自攻螺钉Hexagon flange drilling screw with tapping screw thread 六角法兰面自钻自攻螺钉中文名称英文名称六角螺丝(栓) HEX HEAD CAP SCREWS(HEX BOLTS)六角机械螺丝HEX HEAD MACHINE BOLTS六角木牙螺丝HEX LAG BOLTS四角螺丝SQUARE HEAD BOLTST头螺丝T HEAD BOLTS马车螺丝CARRIAGE BOLTS环首螺丝EYE BOLTS内六角孔螺丝HEX SOCKET CAP SCREWS固定螺丝SET SCREWS螺椿栓STUD BOLTS螺旋椿SCREW STUDS轮壳螺栓WHEEL BOLTS翼形螺丝WING SCREWS自攻螺丝SELF TAPPING SCREWS自削螺丝THREAD CUTTING SCREWS钻尾螺丝SELF DRILLING SCREWS旋入螺丝DRIVE SCREWS机械螺丝MACHINE SCREWS木螺丝WOOD SCREWS家具螺丝FURNITURE SCREWS塑板螺丝CHIPBOARD SCREWS墙用螺丝DRYW ALL SCREWS基础螺栓FOUNDATION BOLTSU型螺栓U BOLTS勾头螺栓HOOK BOLTS套挂螺丝TOGGLE BOLTS突缘螺丝FLANGE BOLTS轨道螺栓(鱼尾螺丝) TRACK BOLTS耐候钢螺丝CORTEN STEEL HEA VY HEX BOLTS扭矩控制螺栓T.C.BOLTS高张力螺栓HIGH STRENGTH BOLTS剪力钉(焊接螺丝) WEL DIN G STUDS螺丝附华司组合SCREWS AND W ASHERS ASSEMBLED(SEMS)大尺寸螺栓BIG SIZE BOLTS不锈钢小螺丝STAINLESS STEEL SHEET METAL SCREWS不锈钢大螺丝STAINLESS STEEL BOLTS铜螺丝BRASS SCREWS铝螺丝ALUMINUM SCREWS合金钢螺丝ALLOY STEEL SCREWS电子螺丝ELECTRONIC SCREWS微小精密螺丝MICRO SCREWS塑料螺丝PLASTIC SCREWS复合材料用螺丝PARTICLE BOARD SCREWS钛合金螺丝TITANIUM ALLOY BOLTS钛、锆、钼、铌等螺丝、零件、材料TI,ZR,MO,NB PARE METAL BOLTS PARTS 拇指螺丝THUMB SCREWS双头牙螺丝DOUBLE END SCREWS HANGER BOLT车辆(汽车)螺丝、螺帽AUTOMOTIVE FASTENERS航天用螺丝AEROSPACE FASTENERS飞机特殊扣件SOURCE CONTROL BOLTS拉栓BLIND BOLTS面板螺丝PANEL FASTENERS电梯螺丝ELEVATOR BOLTS四角头固定螺丝SQUARE SET SCREWS大头马车螺丝STEP BOLTS单向螺丝ONE W AY LAG SCREWS管夹螺丝HOSE CLAMP SCREWS不锈钢固定螺丝STAINLESS STEEL HEX SOCKET CAP SCREWS不锈钢内六角螺丝STAINLESS STEEL HEX SOCKET CAP SCREWS铰链螺丝HINGE SCREWS货柜螺丝CONTAINER SCREWS复合材料钻尾螺丝BI-METAL SELF DRILLING SCREWS三角牙螺丝TRILOBULAR THREAD SCREWS高低牙螺丝HIGH LOW SCREWS夹板用螺丝PARTICLE BOARD SCREWS马桶螺丝TOILET CLOSET BOLTS特长螺丝SPECIAL LONGER SCREWS建业螺丝BUIL DIN G FASTENERS不锈钢六角螺丝STAINLESS STEEL HEX SOCKET CAP SCREWS其它特殊螺丝SPECIAL SCREWS OR BOLTS不锈钢特殊螺丝SPECIAL STAINLESS STEEL SCREWS宽牙螺丝（粗牙螺丝）COARSE THREAD SCREWS链带螺丝COLLATED SCREWS水泥螺丝CONCRETE SCREWS板模螺丝CONSTRUCTION BOLTS锌蝶螺丝DIE CAST WING SCREWS; ZINC ALLOY重型车螺丝HEA VY DUTY WHEEL HUB BOLTS内六角固定螺丝HEX SOCKET SET SCREWS复合材料用螺丝（夹板用）PARTICLE BOARD SCREWS犁壁螺丝PLOW BOLTS机(踏)车用螺丝、轴心SCREWS AND SHAFTS FOR MOTORCYCLE OR BICYCLE 针车用螺丝、轴心SCREWS AND SHAFTS FOR SEWING MACHING止付螺丝SOCKET SET SCREWS不锈钢宽牙螺丝STAINLESS STEEL COARSE THREAD SCREWS不锈钢高低牙螺丝STAINLESS STEEL HIGH-LOW THREAD SCREWS不锈钢机械螺丝STAINLESS STEEL MACHINE SCREWS不锈钢钻尾螺丝STAINLESS STEEL SELF DRILLING SCREWS不锈钢自攻螺丝STAINLESS STEEL SELF TAPPING SCREWS不锈钢自削螺丝STAINLESS STEEL THREAD CUTTING SCREWS不锈钢三角牙螺丝STAINLESS STEEL TRI-LOBULAR THREAD SCREWS不锈钢木螺丝STAINLESS STEEL WOOD SCREWS套挂螺栓及螺丝TOGGLE BOLTS钛合金膨胀螺丝TITANIUM ALLOY EXP ANSI ON BOLTS中文名称英文名称六角盖头螺帽HEX CAP NUTS六角锯齿螺帽HEX SERRATED NUTS六角轮缘螺帽HEX FLANGE NUTS高脚螺帽HEX COUPLING NUTS(HIGH NUTS)圆螺帽ROUND NUTS四角螺帽SQUARE NUTS管用螺帽PIPE NUTS轮壳螺帽WHEEL NUTS蝶型螺帽WING NUTSU形螺帽U NUTST形螺帽T NUTS环首螺帽EYE NUTS齿形螺帽KEP NUTS齿花螺帽CLINCH NUTS耐候钢六角重型螺帽CORTEN STEEL HEA VY HEX NUTS焊接螺帽WELD NUTS高张力螺帽HEIGH STRENGTH NUTS建业用螺帽STRUCTURAL NUTS不锈钢螺帽STAINLESS STEEL NUTS铜螺帽BRASS NUTS铝螺帽ALUMINUM NUTS合金钢螺帽ALLOY STEEL NUTS重型车螺帽HEA VY DUTY WHEEL HUB NUTS铁器焊接袋帽ACORN CAP NUTS金属预置扭矩式螺帽ALL-METAL PREV AILING TORQUE TYPE NUTS壁虎螺帽ANCHOR NUTS大尺寸螺帽BIG SIZE NUTS铁盖袋帽CLOSED END ACORN NUTS盘形华司螺帽CONICAL WASHER NUTS铁盖+尼龙圈组合盖帽DIN 986 DOMED CAP NUTS突缘尼龙盖帽FLANGE NYLON INSERT LOCK NUTS平面华司螺帽FLAT WASER NUTS六角割沟螺帽HEX SLOTTED NUT自锁螺帽SELF-LOCKING NUTS制止螺帽SLI DIN G NUTSSLN-自动防松螺帽SLN SELF-LOCKING NUTS其它特殊螺帽SPECIAL NUTS弹簧螺帽SPRING NUTS不锈钢突缘螺帽STAINLESS STEEL FLANGE NUTS不锈钢六角轮缘尼龙螺帽STAINLESS STEEL FLANGE NYLON INSERT LOCK NUTS 不锈钢六角重型螺帽STAINLESS STEEL HEA VY HEX NUTS不锈钢六角螺帽STAINLESS STEEL HEX NUTS不锈钢尼龙嵌入螺帽STAINLESS STEEL NYLON INSERT LOCK NUTS锌压属螺帽ZINC DIE CASTING NUTS普通六角螺帽HEX NUTS六角重型螺帽HEA VY HEX NUTS薄型螺帽HEX JAM NUTS尼龙嵌入防松螺帽NYLON INSERT LOCK NUTS机械螺丝用六角螺帽HEX MACHINE SCREW NUT中文名称英文名称合金钢线材盘元ALLOY STEEL WIRE ROD球状化线材ANNEALING WIRE AND ROD黑铁丝BLACK WIRE黄铜棒线BRASS WIRE AND ROD磨光棒钢BRIGHT STEEL BAR(HEX/ROUND/SQUARE)铜合金线COPPER ALLOY WIRE线切割线E.D.M CUTTING WIRE快削钢线材盘元FREE CUTTING STEEL WIRE ROD线材IRON OR STEEL WIRE线材盘元IRON OR STEEL WIRE ROD洋白铜线NICKEL SILVER WIRE磷青铜线PHOSPHA TE BRONZE WIRE不锈钢条棒STAINLESS STEEL BAR(ROUND/HEX/SQUARE)不锈钢冷锻线材STAINLESS STEEL COLD HEA DIN G WIRE不锈钢线(抽线后) STAINLESS STEEL DRAW WIRE不锈钢线材STAINLESS STEEL WIRE不锈钢线材及盘元STAINLESS STEEL WIRE AND ROD棒钢STEEL BAR(HEX/ROUND/SQUARE)转回90度碾线头机90讧EVOLVING WIRE TWISTING MACHINE气动拉钉机AIR RIVETER各式螺丝类产品自动包装AUTOMA TIC PACKAGING FOR ALL KINDS OF PACKAGING 自动包装机AUTOMA TIC PACKING MACHINE螺丝制造搓牙机械AUTOMATIC THREAD ROLLING MACHINE螺丝割尾加工机械AUTOMATIC THREAD SLOTTING MACHINE螺丝制造成型机械AUTOMATIC TRIMMING MACHINE拉钉打头机BLIND RIVET HEA DIN G MACHINE螺丝、螺帽成型机BOLT FORMERS,NUTS FORMERS,HEADERS螺丝、螺帽热处理BOLT NUT AND SCREWS HEAT TREATMENT螺丝、螺帽热处理炉BOLT NUT AND SCREWS HEAT TREATMENT FURNACES球状化电器炖炉CARBURIZING FURNACE V ACUUM AND BELL TYPE FURNACE超防锈复合瓷膜CERAMIC COATING连续式光辉渗碳淬火炉CONTINUOUS BRIGHT CARBURIZING QUENCHING FURNACE 连续式光辉调质淬火炉CONTINUOUS BRIGHT HARDENING QUENCHING FURNACE 中、高热镀锌光辉连续炉CONTINUOUS BRIGHT HEAT TREAT FURNACE连续式光辉热处理炉CONTINUOUS TYPE BRIGHT HEAT TREATMENT FURNACE螺丝割尾及特殊割遘加工MACHINE SCREW SHANK SLOTTING螺丝钻孔加工SCREW SHANK DRILLING鸡眼上下模EYELETS DIES一般线材、盘元、退火炉GENERAL WIRE,WIRE ROD,ANNEALING FURNACE倒立式滑落型伸线机HANDSTAND TYPE WIRE DRAWING MACHINE十字冲模HEADER P UNC HES IN V ARIOUS DRIVES成型冲模HEADER P UNC HES IN V ARIOUS DRIVES螺丝打头机HEA DIN G MACHINE螺丝制造高速搓牙机械HIGH SPEED AUTOMA TIC THREAD ROLLING MACHINE高中低周波感应加热炉HIGH,MEDIUM,LOW FREQUENCY INDUCTION HEATER空心打头机HOLLOW HEA DIN G MACHINE热浸镀锌螺丝、螺帽HOT DIP GALV ANIZING BOLTS AND NUTS机械镀锌MECHANICAL GALV ANIZED迷你成型机MINI-FORMERS成品自动收线机NON-STOP COILER精抽自动收线机NON-STOP COILER(SKINPASS)螺帽模NUT FORMING DIES螺帽成型模NUTS FORMERS特殊零件成型机PARTS FORMING MACHING冲模P UNC H DIES冲子P UNC H PINS罗拉成型机ROLLERS FORMERS机(踏)车用螺丝成型机SCREW FOR MOTORCYCLE OR BICYCLE HEA DIN G MACHINE 止付螺丝成型机SET SCREWS FORMERS套高成型机SOCKETS FORMERS一般线材、盘元、螺丝合金炖炉SPHEROIDIZING BRIGHT ANNEALING FURNACE球状化热处理炉SPHEROIDIZING HEAT TREATMENT FURNACE攻牙机TAPPING MACHINE螺丝攻、车刀、模具TAPS DIES AND TOOLS搓牙机铁屑分离装置THREAD CHIP SEPARA TOR滚牙轮THREAD ROLLING DIES牙板THREAD ROLLING DIES PLATES精密油压滚牙机HYDRAULIC THREAD ROLLING MACHINES模具TOOLS六角整头模TRIMMING DIES HEXAGAN碳化钨模具TUNGSTEN CARBIDE DIE镀钛处理(TiN)专业加工服务TiN HARD COA TING FOR CUTTING TOOLS AND P UNC H BY PVD电镀化学原料V ARIOUS ELECTROPLATING CHEMICALS环规校正CALIBRATION FOR RING GAGE环规、牙规、三线规校正CALIBRATION FOR RING GAGE, A THREAD GAGE, 3 WIRE GAGE螺丝、螺帽品检量测仪器FASTENERS INSPECTION AND MEASUREMENT INSTRUMENTS螺丝、螺帽成型攻牙专用油FORMING AND TAPPING OILS FOR BOLTS AND NUTS FORMERS螺丝、螺帽五金等检验INSPTECTION SERVICES FOR FASTENERS AND HARDWARE德国SCHATZ扭力机代理REPRESENTATIVE OF SCHATZ TORQUE MACHINISO品质保证系统ISO QUALITY ASSURANCE SYSTEM生产管理系统PRODUCTION CONTROL SYSTEM物料管理系统MATERIAL CONTROL SYSTEM中文名称英文名称齿轮GEARS不锈钢牙条棒STAINLESS STEEL HREAD ROD马达轴承轴心组件BEARING SHAFT(MOTOR)轴承轴心BEARING SHAFT开口铆钉BLIND RIVETS长形拉帽BLIND RIVET NUTS拉帽BLIND NUTS拉钉BLIND RIVETS实心梢CLEVIS PINS AND STRAIGHT PINS弹片CLIPS卷钉COIL NAILS冷锻零件COLD FORMING PART开口销COTTER PINSE型环E-RINGS膨胀螺栓EXP ANSI ON ANCHOR BOLTS鸡眼钉EYELETS RIVETSR型销SNAP PINS闸、锁LATCHES AND KEEPER ASSEMBLEDS其它特殊铆钉OTHER SPECIL RIVETS销PINS格式管夹、管束PIPE HANGER铆钉RIVETS螺旋锔及螺旋圈SCREW HOOK AND SCREW RINGS中空钉SEMI-TUBULAR RIVET开叉钉SPLIT DRIVE ANCHORS弹簧华司SPRING W ASHERS弹簧蝴蝶夹SPRING WINGS不锈钢华司STAINLESSSTEEL WASHERS钢铁钉STEEL AND IRON NAILS搓牙铁钉THREAD NAILS钛合金铆钉TITAIUM ALLOY RIVETS管形铆钉TUBULAR RIVETS华司W ASHERS真空热处理V ACUUM HEAT TREATMENT螺丝、螺帽、五金、DIY扣件FASTENERS合金钢工具ALLOY STEEL TOOLS螺栓模BOLT HEA DIN G DIES手动拉钉钳HAND RIVETER船舶链ANCHOR CHAIN脚踏车链锁BICYCLE CHAIN LOCKS螺丝起子BIT罗拉CHAIN ROLLER特殊铆合扣件COLLARS(A BLINDFASTENER FOR HUCK INTL)装饰链DECORATIVE CHAINS自攻螺纹衬套ENSAT THREADED INSERTS六角扳手HEXAGON KEYS超音螺纹压入式螺纹自动锁扣THREADED INSERTS FOR PLASTIC INJECTION MOULDEINGS汽车特殊杆接件SPECIAL AUTO-MOBILE FASTENER AS YOUR NEEDS螺纹护套RECOIL INSERTS链条用滚子ROLLER FOR ROLLER CHAIN金属板镶嵌组件及自动夹扣组件SHEET METAL FASTENERS工具套筒组件SOCKET WRENCH SETS不锈钢链STAINLESS STEEL CHAINS轭子T-YOKE轮胎链TIRE CHAINS狗链DOG CHAINS喇叭头轭铁U-YOKE,T-YOKE FOR SPEAKER不锈钢输送带轮用轨道STAINLESS WHEEL'S RACK FOR TRANSPORTER工业用链INDUSTRIAL STEEL LINK CHAINS拖链安全链TOW CHAINS AND SAFETY CHAINS机车离合器零件MANUFACTURE OF MOTORCYCLE'S CVT PARTS牙条棒THREAD ROD貨運用語的中英文對照货物goods | freight | cargo运输transportation | transit | conveyance运送to transport | to carry | to convey运输业transportation business | forwarding business | carrying trade运输代理人a forwarding agent承运人a freight agent | a carrier船务代理人a shipping agent陆上运输transportation by land海上运输transportation by sea货物运输goods traffic | freight traffic | carriage of freights | carriage of goods 货轮cargo boat | freighter | cargo steamer | cargo carrier火车goods-train | freight-train卡车goods-van | goods wagon | freight car | truck货运办公室goods-office | freight-department运费率freight | freight rates | goods rate运费carriage charges | shipping expenses | express charges车费cartage | portage运费预付carriage prepaid | carriage paid运费到付carriage forward | freight collect运费免除||免费carriage free协定运费conference freight | freight rate运费清单freight account托运单way-bill | invoice运送契约contract for carriage装运shipment | loading装上货轮to ship | to load | to take on a ship装运费shipping charges | shipping commission装运单||载货单shipping invoice装运单据shipping documents大副收据mate's receipt装船单shipping order提货单delivery order装船通知shipping advice包裹收据parcel receipt准装货单shipping permit租船契约charter party租船人charterer程租船||航次租赁voyage charter期租船time charter允许装卸时间lay days | laying days工作日working days连续天数running days | consecutive days滞期费demurrage滞期日数demurrage days速遣费despatch money空舱费dead freight退关short shipment | goods short shipped | goods shut out | shut-outs赔偿保证书(信托收据) letter of indemnity | trust receipt装载loading卸货unloading | discharging | landing装运重量shipping weight | in-take-weight卸货重量landing weight压舱ballasting压舱货in ballast舱单manifest船泊登记证书ship's certificate of registry 航海日记ship's log船员名册muster-roll（船员，乘客）健康证明bill of health光票clean bill不清洁提单foul bill有疑问提单suspected bill。

101 DIN927 开槽无头轴肩螺钉slotted shoulder screws102 DIN928 焊接方螺母square weld nuts GB/T13680-92103 DIN929 焊接六角螺母hexagon weld nuts GB/T13681-92104 DIN931 六角头螺栓（半牙）hexagon head screws ISO4014 GB5782-86 105 DIN933 六角头螺栓（全牙）hexagon head screws ISO4017 GB5783-86 106 DIN934 六角头螺母(1型) hexagon full nuts ISO4032 GB6170-86107 DIN934 细牙六角头螺母(1型) hexagon full nuts ISO8673 GB6171-86108 DIN935 开槽六角螺母hexagon slotted and castle nuts ISO7035 GB6178-86 109 DIN936 六角头薄螺母hexagon thin nuts ISO4035 GB6172.1-86110 DIN937 六角头开槽薄螺母hexagon thin slotted and castle nuts ISO7038 GB6181-86111 DIN938 双头螺距（牙长=1D）studs metal (end=1d) GB897-88112 DIN939 双头螺距（牙长=1.25D）studs metal (end=1.25d)GB898-88113 DIN940 双头螺距（牙长=1.5D）studs metal (end=1.5d)114 DIN960 六角头细牙螺栓（半牙）hexagon head bolts,metric fine pitchthread ISO8765 GB5785-86115 DIN961 六角头细牙螺栓（全牙）hexagon head bolts,metric fine pitchthread ISO8676 GB5786-86116 DIN962 头部穿孔六角头螺栓additional shapes and versions for bolts117 DIN963 开槽沉头螺钉slotted countersund head screwsISO 2009 GB68-85118 DIN964 开槽半沉头螺钉slotted raised countersunk oval head screwsISO 2010 GB69-85119 DIN965 十字槽沉头螺钉cross recessed countersunk headscrews ISO7046 GB819-85120 DIN966 十字槽半沉头螺钉cross recessed raised countersunk headscrews ISO7047 GB820-85121 DIN970 六角头螺母hexagon nuts type-1122 DIN971 六角头螺母hexagon nuts type-2123 DIN972 细牙六角头螺母(2型) hexagon nuts with fine thread ISO8674 GB6176-86 124 DIN975 牙条(全螺纹) threaded rods(studdings)GB15389-94125 DIN976 螺纹销threaded pins(stud bolts)126 DIN979 六角头开槽薄螺母（2型）hexagon thin slotted and castle nuts127 DIN980 全金属六角锁紧螺母（1型）prevailling torque type hexagon nuts,all metall nuts ISO7199 GB6184-86128 DIN981 圆螺母locknuts ISO2982 GB812-88129 DIN982 六角头尼龙锁紧螺母prevailling torque type hexagon nuts,heavy type ,with nylon insert ISO7040 GB889.1-86130 DIN985 六角头薄型尼龙锁紧螺母prevailling torque type hexagon nuts,heavy type ,with nylon insert ISO10511 GB6172.2-86131 DIN986 六角盖型尼龙锁紧螺母prevailling torque typedomed capnuts with nylon insert132 DIN988 配合垫片shim rings133 DIN1052 木材连接用垫片washers for timber connectors134 DIN1151 沉头钢钉round plain head nails135 DIN1440 销钉专用垫片A型plain washers for clevis pins(A型) ISO8738136 DIN1441 销钉专用垫片plain washers for clevis pins137 DIN1444 带头销钉clevis pins with head ISO2341138 DIN1471 圆锥型槽销grooved pins,taper grooved ISO8744 GB/T13829.2139 DIN1472 圆锥型槽销(半槽)grooved pins,taper grooved halflength ISO8745 GB/T13829.2140 DIN1473 平行槽销(带倒角) grooved pins,parallel grooved full length ISO8740141 DIN1474 前端凹槽槽销grooved pins,reserve grooved half length ISO8741142 DIN1475 中部凹槽槽销grooved pins,centre grooved ISO8742143 DIN1476 圆头槽销grooved pins with round head ISO8746 GB/T13829.3144 DIN147 7沉头槽销grooved pins with countersunk head ISO8747145 DIN1479 六角螺母棒turnuckles(centre parts),made out of hexagon bar146 DIN1480 花篮螺栓turnuckles with eye bolt and hook bolt147 DIN1481 弹性圆柱销spring pins,heavy type ISO8752 GB879-86148 DIN1587 组合式盖型螺母hexagon domed cap nuts GB802-88149 DIN1804 开槽圆螺母（配合沟头扳手）slotted round nuts for hook spanner150 DIN1816 圆螺母（带插销孔）round nuts with set holes151 DIN2093 盘型弹簧垫圈disc springs152 DIN3017 喉箍hose clamps153 DIN3404 润滑油嘴（旋扭头）lubricating nipples,button head154 DIN3567 管夹shackles for conduilts155 DIN3570 U型螺栓stirrup bolts(U-bolts)156 DIN6319 球面垫圈spherical washers,conical seats GB849-88157 DIN6325 圆柱销parallel pins ISO8734158 DIN6330 厚六角螺母hexagon nuts ,1.5d GB56-88159 DIN6331 厚六角法兰面螺母hexagon nuts ,1.5d with collar GB6177-86160 DIN6334 长六角螺母hexagon nuts ,3d161 DIN6797-A 外齿锁紧垫圈external teeth lock washers GB862.1-87162 DIN6797-I 内齿锁紧垫圈internal teeth lock washers GB861.1-87163 DIN6798-A 外锯齿锁紧垫圈external teeth serrated lock washers GB862.2-87 164 DIN6798-I 内锯齿锁紧垫圈internal teeth serrated lock washers GB861.2-87165 DIN6799 开口挡圈retaining rings for shafts(E-rings),circlips GB896-76166 DIN6885 平键（A型）parallel keys(form A ) ISO773/2491167 DIN6888 半圆键woodruff keys ISO3912168 DIN6899 嵌环（支撑环）thimbles169 DIN6900 机器螺钉和垫圈组合件screws and washers assemblies GB9074.1-.17 170 DIN6901 自攻螺钉和垫圈组合件tapping screws and washersassemblies GB9074.18-.23171 DIN6912 薄型带孔内六角圆柱头螺钉hexagon socket head cap screws with hole,low head172 DIN6914 大六角头螺栓hexagon head bolts with large head(friction grip bolts)173 DIN6915 大六角螺母hexagon nuts with large wideth across flat(friction grip nuts)174 DIN6916 大垫圈round washers for friction grip bolts175 DIN6917 楔型方垫圈spuare taper washers for friction grip bolts onT-sections176 DIN6923 六角法兰面螺母hexagon flange nuts ISO4161 GB6177-86177 DIN6925 全金属六角锁紧螺母(2型）prevailing torque type hexagon nuts,all metallic nuts ISO7042 GB6185.1-2000178 DIN7337 开口型抽芯铆钉（沉头、扁圆头）blind rivets GB12617/12618 179 DIN7338 扁平头半空心/全空心铆钉rivets for brake and clutchlining GB875/975-86180 DIN7343 螺旋夹紧销spiral pins ISO8750181 DIN7346 轻型弹性圆柱销spring pins,light type ISO13337182 DIN7349 重型弹性圆柱销用垫圈washers for bolts with heavy type spring pinss183 DIN7500 ISO公制螺纹螺钉(多种头型) threadforming screws for ISO-metricthread184 DIN7504 自攻自钻螺钉(多种头型) self-drilling tapping screws185 DIN7513 开槽切削螺纹螺钉(多种头型) thread cutting screws186 DIN7516 十字槽切削螺纹螺钉(多种头型) thread cutting screws cross recess187 DIN7965 T型四爪螺母tee nuts with pronge188 DIN7968 钢结构用六角头螺栓连接副hexagon head fitted bolts for steel structures GB1228/1229/1230189 DIN7971 开槽盘头自攻螺钉pan head tapping screws with slot ISO1481 GB5282-85190 DIN7972 开槽沉头自攻螺钉countersunk flat head tapping screws with slot ISO1482 GB5283-85191 DIN7973 开槽半沉头自攻螺钉raised countersunk oval head tapping screws with slot ISO1483 GB5284-85192 DIN7976 六角头自攻螺钉hexagon tapping screws ISO1479 GB5285-85 193 DIN7980 圆柱头螺钉用弹簧垫圈spring lock washers for screws with cylindrical headsISO8738194 DIN7981 十字槽盘头自攻螺钉pan head tapping screws with cross recessed ISO7049 GB845-85195 DIN7982 十字槽沉头自攻螺钉countersunk flat head tapping screws with cross recessed ISO7050 GB846-85196 DIN7983 十字槽半沉头自攻螺钉raised countersunk oval head tapping screws with cross recessed ISO7051 GB847-86197 DIN7984 薄型内六角圆柱头螺钉hexagon socket head cap screws with，reduced head198 DIN7985 十字槽盘头螺钉pan head screws with cross recessed ISO7045 GB818-85 199 DIN7989 钢结构用垫圈washers for steel structures GB1230-84200 DIN7990 钢结构用六角头螺栓hexagon head bolts for steel structuresGB1229-84201 DIN7991 内六角沉头螺钉hexagon socket countersunk head screws ISO10642202 DIN7993 轴用钢丝挡圈roundwire snap rings for shafts GB895.2-86203 DIN7995 十字槽半沉头木螺钉cross recessed raised countersunk head wood screws GB952-86204 DIN7996 十字槽圆头木螺钉cross recessed round head wood screws GB950-86 205 DIN7997 十字槽沉头木螺钉cross recessed countersunk head woodscrews GB951-86206 DIN8140 螺纹护套（普通\自锁等）ciol inserts,coarse,fine thread,silf locking207 DIN9021 大外径垫圈washers,outside diameter appro.3d ISO7093 GB96-85 208 DIN11024 弹簧卡子spring cotter for a bolt209 DIN13257 平板螺栓belting bolts (elevator bolts)210 DIN18182 干壁钉（墙板钉）dry wall screws211 DIN28129 环型螺母lifting nuts(eye nuts)GB63-88212 DIN70952 圆螺母用止退垫圈tab washers for slotted round nuts GB858-88。

一.孔别紧固件常用英文对照1.割沟Slotted2.十字穴Phillips3.米字穴Pozidriv(cross recess)4.十字割沟Slotted phillips5.四角孔Square6.十字方孔Square phillips7.六角孔hexagon 8.方孔割沟Square slotted 9.梅花穴Six-lobe 10.三角孔Triangle 11.Y型槽Y-type 12.斜Y槽Tri-wing 13.五等角5-Point 二,电镀1.电镀锌Zinc plated2.白皮Plain finished3.五彩Yellow zinc plated4.镀镍Nickel plated5.热浸锌Hot dip galvanized6.黑锌Black zinc plated7.镀黑Black finished 8.染黑Black oxide 9.(黑)磷酸盐(black)Phosphated 10.黄铜Brass 11.镀青蓝Unichrome plated 12.古铜A.C Brontze13.青古铜Antique brass 14.机械镀锌Mechanical galvanized 15.绿锌Green zinc plated 16.电锌腊Zinc plated&waxed 17.达克锈Dacrotizing plated18.久美特Geomet 19.耐落Nylok陆锈宝Rupst 20.翡丽雅特ViridAct 21.美加力Magni三.常用名称1.螺丝类中文名称方头螺栓沉头方劲螺栓沉头沉带榫螺栓(大)半圆头方颈螺栓六角头铰制孔用螺栓英文名称Square head boltsFlat countersunk square neck boltsFlate countersunk nib boltsCup head square neck (with large head)boltHexagon fit bolts对应标准GB/T 8-88 C级GB/T 10-88GB/T 11-88GB/T 14/15-88GB/T 27-88 A和B级六角头螺杆带铰制孔用螺栓(细杆) Hexagon fit bolts with split pin hole on shank(Reduced shank) GB/T 28-88 A和B级十字槽凹穴六角头螺栓六角头头部带孔螺栓T型槽用螺栓加强半圆头方颈螺栓活节螺栓地角螺栓头角头螺栓六角头法兰面螺栓外六角花法兰面螺栓Cross recessed hexagon bolts with indentationHexagon bolts with wire holes on headBolt for T-slotStrengthened cap head square neck boltsEye boltsEyelet boltsHexagon head boltsHexagon flange boltsSteel hexalobular head bolt with small flangeGB/T 29.2-88 A和B级GB/T 32.1-88 A和B级GB/T 35.1-88 B级GB/T 794.1-93GB/T798-88GB/T799-88GB/T5780-2000 C级GB/T5789-86 B级DIN 34801-99PDF created with pdfFactory Pro trial version .中文名称英文名称对应标准双头螺柱bm=1d等长双头螺柱B级螺杆3.螺钉类中文名称开槽圆柱头螺钉开槽沉头螺钉开槽半沉头螺钉内六角圆柱头螺钉内六角平圆头螺钉内六角沉头螺钉十字槽盘头螺钉十字槽半沉头螺钉十字槽圆柱头螺钉滚花高头螺钉滚花平头螺钉内六角花形盘头螺钉内六角圆柱头轴肩螺钉4.自攻螺钉中文名称十字槽盘头盘自攻螺钉十字槽沉头盘自攻螺钉十字槽盘头盘自攻锁紧螺钉十字槽凹穴六角头自攻螺钉Double end studs-bm=1dDouble end studs(clamping type)-product grade AThread rods英文名称Slotted cheese head screwsSlotted countersunk flat head screws (mon head style)Countersunk slotted raised head screws(mon head style)Hexagon socket head cap screwsHexagon socket button head screwsHexagon socket countersunk head screwsPan head screw with cross recessCountersunk raised head screws(mon head style)with cross recessCheese head screws with cross recessKnurled thumb screwsKnurled screwsHexagon lobular socket pan head scerwsHexagon socket head shoulder scerws英文名称Cross recessed pan head tapping screwsCross recessed countersunk head tapping screwsCross recessed pan head thread forming screwsCross recessed hexagon head tapping screws with indentationGB/T 897-88GB/T 901-88GB/T 15389-94对应标准GB/T65-2000GB/T68-2000 eqv ISO 2009-94GB/T69-2000 eqv ISO 2010-94GB/T70.1-2000 eqv ISO 4762.2-97GB/T70.2-2000 eqv ISO 7380-97GB/T70.3-2000 eqv ISO 10642-97GB/T818-2000 eqv ISO 7045-94GB/T820-2000 eqv ISO 7047-94GB/T822-2000 eqv ISO 7048-94GB 834-88GB 835-88GB 2672-86GB/T 5281-85对应标准GB 845-85GB 846-85GB 6560-86GB 9456-98十字槽自攻螺钉-刮削端(用于精密机械) cross recessed tapping screws-scrape point(fasters for fine mechanics) GB/T 13806-2墙板自攻螺钉十字槽盘头自钻自攻螺钉六角凸缘自攻螺钉Dry wall screwsCross recessed pan head self-drilling tapping screwsHexagon head tapping screws with collarGB/T14210-93GB/T15856.1-95GB/T16824.1-97 eqv ISO 7053-92中文名称英文名称对应标准方螺母-C级六角螺母-C级六角厚螺母六角薄螺母蝶形螺母组合式盖形螺母球面六角螺母滚花高螺母1型非金属嵌件六角锁紧螺母盖形螺母六角薄螺母无倒角六角法兰面螺母1型六角开槽螺母全金属六角锁紧螺母焊接方螺母焊接六角螺母平头铆螺母6.挡圈中文名称锥销锁紧挡圈轴肩挡圈螺钉紧固轴端挡圈孔用弹性挡圈-A型轴用弹性挡圈开口挡圈钢丝锁圈夹紧挡圈Square nuts-product grade CHexagon nuts-product grade CHexagon thick nutsHexagon thin nutsWing nutsAcorn nutsHexagon nut with raised facekunrled nut with collarPrevailing torque type hexagon nuts(with non-metallic insert).style 1Acorn nutsHexagon thin nuts (unchamfered)Hexagon nuts with flangeHexagon slotted and castle nuts.style1Prevailing torque type all-metal hexagon nutssquare weld nutHexagon weld nutsFlat head riveted nuts英文名称Lock ring with corne pinRings for shouderLock rings at the end of shaft with screwCirclips for holes -typeACirclips for shaft -typeA"E"ringsRound coire circlipsCrip ringsGB/T39-88GB/T41-2000eqv ISO 4034-99GB/T56-88GB/T6172.1-2000eqvISO 4035-99GB/T 62-88GB/T 802-88GB/T 804-88GB/T 806-88GB/T889.1-2000eqv 7040-97GB/T 923-88GB/T6174-2000eqvISO 4036-99GB/T6177.1-2000eqv ISO 4161-99GB/T 6178-86GB/T 6184-2000eqv ISO 7719-97GB/T 13680-92GB/T 13681-92GB/T 17880.1-99对应标准GB/T 883-86GB/T 891-86GB/T 893.1-86GB/T 894.1-86GB/T 895-2-86GB/T 896-86GB/T 921-86GB/T 960-867.垫圈类中文名称英文名称对应标准弹簧垫圈(标准型)平垫圈-C级大平垫圈鞍形弹性垫圈内齿锁紧垫圈内锯齿锁紧垫圈外锯齿锁紧垫圈波型弹性垫圈锥形锁紧垫圈锥形锯齿锁紧垫圈8.销中文名称开口销圆锥销螺纹圆柱销销轴平头铆钉平锥头铆钉（粗制）空心铆钉封闭型扁圆头抽芯铆钉开口型沉头抽芯铆钉Single coil spring lock washers (normal type)Plain washersPlain washers-large seriesCurved spring washersLock washers internal teethSerrated lock washers internal teethSerrated lock washers external teethWave spring washersCountersunk external toothed look washersCountersunk serrated external toothed lock washers英文名称Split pinsTaper pinsParaller pins with external threadClevis pins with headFlat head rivetsCone-head rivets-blackTubular rivetsMushroom head break mandred closed end blind rivets120 deg flush head break mandrel blind rivetsGB/T 93-87GB/T 95-85eqv ISO 7091-2000GB/T 96-85 A和B级GB/T 860-87GB/T 861.1-87GB/T 861.2-87GB/T 862.2-87GB/T 955-87GB/T 956.1-87GB/T 956.2-87对应标准GB/T 91-2000eqvISO1234-97GB/T 117-2000eqvISO2339-86GB/T 878-86GB/T 882-86GB/T 109-86GB/T 864-86GB/T 876-86GB/T 12615-90GB/T 12617-909.紧固件-组合件和连接副中文名称英文名称紧固件常用英文对照对应标准钢结构用高强度大六角头螺栓钢结构用高强度大六角头螺母钢结构用高强度大六角头垫圈High strength bolts with large hexagon head for steel structuresHigh strength large hexagon nuts for steel stucturesHigh strength plain washers for steel structuresGB/T1230-91GB/T1229-91GB/T1230-91钢结构用扭剪型高强度螺栓连接副Sets of torshear type high strength bolt hexagon nut and plain washer for steel structures GB/T3632-95十字槽盘头螺钉,弹簧垫圈和平垫圈组合件Cross recessed pan head screw ,single coil spring lock washer and plain washer assemblies GB/T 9074-.4-88无头焊钉圆柱头焊钉机械焊接螺钉Headless for stud weldingCheese head studs for stud weldingWeld screws with metric threadGB/T 10432-89GB/T 10433-89DIN 34817-2001Word 是学生和职场人士最常用的一款办公软件之一，99.99%的人知道它，但其实，这个软件背后，还有一大批隐藏技能你不知道。

中文名称 英文名称六角螺丝(栓) HEX HEAD CAP SCREWS(HEX BOLTS)六角机械螺丝 HEX HEAD MACHINE BOLTS六角木牙螺丝 HEX LAG BOLTS四角螺丝 SQUARE HEAD BOLTST头螺丝 T HEAD BOLTS马车螺丝 CARRIAGE BOLTS环首螺丝 EYE BOLTS内六角孔螺丝 HEX SOCKET CAP SCREWS固定螺丝 SET SCREWS螺椿栓 STUD BOLTS螺旋椿 SCREW STUDS轮壳螺栓 WHEEL BOLTS翼形螺丝 WING SCREWS自攻螺丝 SELF TAPPING SCREWS自削螺丝 THREAD CUTTING SCREWS钻尾螺丝 SELF DRILLING SCREWS旋入螺丝 DRIVE SCREWS机械螺丝 MACHINE SCREWS木螺丝 WOOD SCREWS家具螺丝 FURNITURE SCREWS塑板螺丝 CHIPBOARD SCREWS墙用螺丝 DRYWALL SCREWS基础螺栓 FOUNDATION BOLTSU型螺栓 U BOLTS勾头螺栓 HOOK BOLTS套挂螺丝 TOGGLE BOLTS突缘螺丝 FLANGE BOLTS轨道螺栓(鱼尾螺丝) TRACK BOLTS耐候钢螺丝 CORTEN STEEL HEAVY HEX BOLTS扭矩控制螺栓 T.C.BOLTS高张力螺栓 HIGH STRENGTH BOLTS剪力钉(焊接螺丝) WELDING STUDS螺丝附华司组合 SCREWS AND WASHERS ASSEMBLED(SEMS)大尺寸螺栓 BIG SIZE BOLTS不锈钢小螺丝 STAINLESS STEEL SHEET METAL SCREWS不锈钢大螺丝 STAINLESS STEEL BOLTS铜螺丝 BRASS SCREWS铝螺丝 ALUMINUM SCREWS合金钢螺丝 ALLOY STEEL SCREWS电子螺丝 ELECTRONIC SCREWS微小精密螺丝 MICRO SCREWS塑料螺丝 PLASTIC SCREWS复合材料用螺丝 PARTICLE BOARD SCREWS钛合金螺丝 TITANIUM ALLOY BOLTS钛、锆、钼、铌等螺丝、零件、材料 TI,ZR,MO,NB PARE METAL BOLTS PARTS 拇指螺丝 THUMB SCREWS双头牙螺丝 DOUBLE END SCREWS HANGER BOLT车辆(汽车)螺丝、螺帽 AUTOMOTIVE FASTENERS航天用螺丝 AEROSPACE FASTENERS飞机特殊扣件 SOURCE CONTROL BOLTS拉栓 BLIND BOLTS面板螺丝 PANEL FASTENERS电梯螺丝 ELEVATOR BOLTS四角头固定螺丝 SQUARE SET SCREWS大头马车螺丝 STEP BOLTS单向螺丝 ONE WAY LAG SCREWS管夹螺丝 HOSE CLAMP SCREWS不锈钢固定螺丝 STAINLESS STEEL HEX SOCKET CAP SCREWS不锈钢内六角螺丝 STAINLESS STEEL HEX SOCKET CAP SCREWS铰链螺丝 HINGE SCREWS货柜螺丝 CONTAINER SCREWS复合材料钻尾螺丝 BI-METAL SELF DRILLING SCREWS三角牙螺丝 TRILOBULAR THREAD SCREWS高低牙螺丝 HIGH LOW SCREWS夹板用螺丝 PARTICLE BOARD SCREWS马桶螺丝 TOILET CLOSET BOLTS特长螺丝 SPECIAL LONGER SCREWS建业螺丝 BUILDING FASTENERS不锈钢六角螺丝 STAINLESS STEEL HEX SOCKET CAP SCREWS其它特殊螺丝 SPECIAL SCREWS OR BOLTS不锈钢特殊螺丝 SPECIAL STAINLESS STEEL SCREWS宽牙螺丝（粗牙螺丝） COARSE THREAD SCREWS链带螺丝 COLLATED SCREWS水泥螺丝 CONCRETE SCREWS板模螺丝 CONSTRUCTION BOLTS锌蝶螺丝 DIE CAST WING SCREWS; ZINC ALLOY重型车螺丝 HEAVY DUTY WHEEL HUB BOLTS内六角固定螺丝 HEX SOCKET SET SCREWS复合材料用螺丝（夹板用） PARTICLE BOARD SCREWS犁壁螺丝 PLOW BOLTS机(踏)车用螺丝、轴心 SCREWS AND SHAFTS FOR MOTORCYCLE OR BICYCLE 针车用螺丝、轴心 SCREWS AND SHAFTS FOR SEWING MACHING止付螺丝 SOCKET SET SCREWS不锈钢宽牙螺丝 STAINLESS STEEL COARSE THREAD SCREWS不锈钢高低牙螺丝 STAINLESS STEEL HIGH-LOW THREAD SCREWS不锈钢机械螺丝 STAINLESS STEEL MACHINE SCREWS不锈钢钻尾螺丝 STAINLESS STEEL SELF DRILLING SCREWS不锈钢自攻螺丝 STAINLESS STEEL SELF TAPPING SCREWS不锈钢自削螺丝 STAINLESS STEEL THREAD CUTTING SCREWS不锈钢三角牙螺丝 STAINLESS STEEL TRI-LOBULAR THREAD SCREWS不锈钢木螺丝 STAINLESS STEEL WOOD SCREWS套挂螺栓及螺丝 TOGGLE BOLTS钛合金膨胀螺丝 TITANIUM ALLOY EXPANSION BOLTS中文名称 英文名称六角盖头螺帽 HEX CAP NUTS六角锯齿螺帽 HEX SERRATED NUTS六角轮缘螺帽 HEX FLANGE NUTS高脚螺帽 HEX COUPLING NUTS(HIGH NUTS)圆螺帽 ROUND NUTS四角螺帽 SQUARE NUTS管用螺帽 PIPE NUTS轮壳螺帽 WHEEL NUTS蝶型螺帽 WING NUTSU形螺帽 U NUTST形螺帽 T NUTS环首螺帽 EYE NUTS齿形螺帽 KEP NUTS齿花螺帽 CLINCH NUTS耐候钢六角重型螺帽 CORTEN STEEL HEAVY HEX NUTS焊接螺帽 WELD NUTS高张力螺帽 HEIGH STRENGTH NUTS建业用螺帽 STRUCTURAL NUTS不锈钢螺帽 STAINLESS STEEL NUTS铜螺帽 BRASS NUTS铝螺帽 ALUMINUM NUTS合金钢螺帽 ALLOY STEEL NUTS重型车螺帽 HEAVY DUTY WHEEL HUB NUTS铁器焊接袋帽 ACORN CAP NUTS金属预置扭矩式螺帽 ALL-METAL PREVAILING TORQUE TYPE NUTS壁虎螺帽 ANCHOR NUTS大尺寸螺帽 BIG SIZE NUTS铁盖袋帽 CLOSED END ACORN NUTS盘形华司螺帽 CONICAL WASHER NUTS铁盖+尼龙圈组合盖帽 DIN 986 DOMED CAP NUTS突缘尼龙盖帽 FLANGE NYLON INSERT LOCK NUTS平面华司螺帽 FLAT WASER NUTS六角割沟螺帽 HEX SLOTTED NUT自锁螺帽 SELF-LOCKING NUTS制止螺帽 SLIDING NUTSSLN-自动防松螺帽 SLN SELF-LOCKING NUTS其它特殊螺帽 SPECIAL NUTS弹簧螺帽 SPRING NUTS不锈钢突缘螺帽 STAINLESS STEEL FLANGE NUTS不锈钢六角轮缘尼龙螺帽 STAINLESS STEEL FLANGE NYLON INSERT LOCK NUTS 不锈钢六角重型螺帽 STAINLESS STEEL HEAVY HEX NUTS不锈钢六角螺帽 STAINLESS STEEL HEX NUTS不锈钢尼龙嵌入螺帽 STAINLESS STEEL NYLON INSERT LOCK NUTS锌压属螺帽 ZINC DIE CASTING NUTS普通六角螺帽 HEX NUTS六角重型螺帽 HEAVY HEX NUTS薄型螺帽 HEX JAM NUTS尼龙嵌入防松螺帽 NYLON INSERT LOCK NUTS机械螺丝用六角螺帽 HEX MACHINE SCREW NUT中文名称 英文名称合金钢线材盘元 ALLOY STEEL WIRE ROD球状化线材 ANNEALING WIRE AND ROD黑铁丝 BLACK WIRE黄铜棒线 BRASS WIRE AND ROD磨光棒钢 BRIGHT STEEL BAR(HEX/ROUND/SQUARE)铜合金线 COPPER ALLOY WIRE线切割线 E.D.M CUTTING WIRE快削钢线材盘元 FREE CUTTING STEEL WIRE ROD线材 IRON OR STEEL WIRE线材盘元 IRON OR STEEL WIRE ROD洋白铜线 NICKEL SILVER WIRE磷青铜线 PHOSPHATE BRONZE WIRE不锈钢条棒 STAINLESS STEEL BAR(ROUND/HEX/SQUARE)不锈钢冷锻线材 STAINLESS STEEL COLD HEA DING WIRE不锈钢线(抽线后) STAINLESS STEEL DRAW WIRE不锈钢线材 STAINLESS STEEL WIRE不锈钢线材及盘元 STAINLESS STEEL WIRE AND ROD棒钢 STEEL BAR(HEX/ROUND/SQUARE)转回90度碾线头机 90讧EVOLVING WIRE TWISTING MACHINE气动拉钉机 AIR RIVETER各式螺丝类产品自动包装 AUTOMATIC PACKAGING FOR ALL KINDS OF PACKAGING 自动包装机 AUTOMATIC PACKING MACHINE螺丝制造搓牙机械 AUTOMATIC THREAD ROLLING MACHINE螺丝割尾加工机械 AUTOMATIC THREAD SLOTTING MACHINE螺丝制造成型机械 AUTOMATIC TRIMMING MACHINE拉钉打头机 BLIND RIVET HEADING MACHINE螺丝、螺帽成型机 BOLT FORMERS,NUTS FORMERS,HEADERS螺丝、螺帽热处理 BOLT NUT AND SCREWS HEAT TREATMENT螺丝、螺帽热处理炉 BOLT NUT AND SCREWS HEAT TREATMENT FURNACES球状化电器炖炉 CARBURIZING FURNACE VACUUM AND BELL TYPE FURNACE超防锈复合瓷膜 CERAMIC COATING连续式光辉渗碳淬火炉 CONTINUOUS BRIGHT CARBURIZING QUENCHING FURNACE 连续式光辉调质淬火炉 CONTINUOUS BRIGHT HARDENING QUENCHING FURNACE 中、高热镀锌光辉连续炉 CONTINUOUS BRIGHT HEAT TREAT FURNACE连续式光辉热处理炉 CONTINUOUS TYPE BRIGHT HEAT TREATMENT FURNACE 螺丝割尾及特殊割遘加工 MACHINE SCREW SHANK SLOTTING螺丝钻孔加工 SCREW SHANK DRILLING鸡眼上下模 EYELETS DIES一般线材、盘元、退火炉 GENERAL WIRE,WIRE ROD,ANNEALING FURNACE 倒立式滑落型伸线机 HANDSTAND TYPE WIRE DRAWING MACHINE十字冲模 HEADER PUNCHES IN VARIOUS DRIVES成型冲模 HEADER PUNCHES IN VARIOUS DRIVES螺丝打头机 HEADING MACHINE螺丝制造高速搓牙机械 HIGH SPEED AUTOMATIC THREAD ROLLING MACHINE高中低周波感应加热炉 HIGH,MEDIUM,LOW FREQUENCY INDUCTION HEATER空心打头机 HOLLOW HEADING MACHINE热浸镀锌螺丝、螺帽 HOT DIP GALVANIZING BOLTS AND NUTS机械镀锌 MECHANICAL GALVANIZED迷你成型机 MINI-FORMERS成品自动收线机 NON-STOP COILER精抽自动收线机 NON-STOP COILER(SKINPASS)螺帽模 NUT FORMING DIES螺帽成型模 NUTS FORMERS特殊零件成型机 PARTS FORMING MACHING冲模 PUNCH DIES冲子 PUNCH PINS罗拉成型机 ROLLERS FORMERS机(踏)车用螺丝成型机 SCREW FOR MOTORCYCLE OR BICYCLE HEA DING MACHINE止付螺丝成型机 SET SCREWS FORMERS套高成型机 SOCKETS FORMERS一般线材、盘元、螺丝合金炖炉 SPHEROIDIZING BRIGHT ANNEALING FURNACE球状化热处理炉 SPHEROIDIZING HEAT TREATMENT FURNACE攻牙机 TAPPING MACHINE螺丝攻、车刀、模具 TAPS DIES AND TOOLS搓牙机铁屑分离装置 THREAD CHIP SEPARATOR滚牙轮 THREAD ROLLING DIES牙板 THREAD ROLLING DIES PLATES精密油压滚牙机 HYDRAULIC THREAD ROLLING MACHINES模具 TOOLS六角整头模 TRIMMING DIES HEXAGAN碳化钨模具 TUNGSTEN CARBIDE DIE镀钛处理(TiN)专业加工服务 TiN HARD COATING FOR CUTTING TOOLS AND PUNCH BY PVD 电镀化学原料 VARIOUS ELECTROPLATING CHEMICALS环规校正 CALIBRATION FOR RING GAGE环规、牙规、三线规校正 CALIBRATION FOR RING GAGE, ATHREAD GAGE, 3 WIRE GAGE螺丝、螺帽品检量测仪器 FASTENERS INSPECTION AND MEASUREMENT INSTRUMENTS螺丝、螺帽成型攻牙专用油 FORMING AND TAPPING OILS FOR BOLTS AND NUTS FORMERS螺丝、螺帽五金等检验 INSPTECTION SERVICES FOR FASTENERS AND HARDWARE德国SCHATZ扭力机代理 REPRESENTATIVE OF SCHATZ TORQUE MACHINISO质量保证系统 ISO QUALITY ASSURANCE SYSTEM生产管理系统 PRODUCTION CONTROL SYSTEM物料管理系统 MATERIAL CONTROL SYSTEM中文名称 英文名称齿轮 GEARS不锈钢牙条棒 STAINLESS STEEL HREAD ROD马达轴承轴心组件 BEARING SHAFT(MOTOR)轴承轴心 BEARING SHAFT开口铆钉 BLIND RIVETS长形拉帽 BLIND RIVET NUTS拉帽 BLIND NUTS拉钉 BLIND RIVETS实心梢 CLEVIS PINS AND STRAIGHT PINS弹片 CLIPS卷钉 COIL NAILS冷锻零件 COLD FORMING PART开口销 COTTER PINSE型环 E-RINGS膨胀螺栓 EXPANSION ANCHOR BOLTS鸡眼钉 EYELETS RIVETSR型销 SNAP PINS闸、锁 LATCHES AND KEEPER ASSEMBLEDS其它特殊铆钉 OTHER SPECIL RIVETS销 PINS格式管夹、管束 PIPE HANGER铆钉 RIVETS螺旋锔及螺旋圈 SCREW HOOK AND SCREW RINGS中空钉 SEMI-TUBULAR RIVET开叉钉 SPLIT DRIVE ANCHORS弹簧华司 SPRING WASHERS弹簧蝴蝶夹 SPRING WINGS不锈钢华司 STAINLESSSTEEL WASHERS钢铁钉 STEEL AND IRON NAILS搓牙铁钉 THREAD NAILS钛合金铆钉 TITAIUM ALLOY RIVETS管形铆钉 TUBULAR RIVETS华司 WASHERS真空热处理 VACUUM HEAT TREATMENT螺丝、螺帽、五金、DIY扣件 FASTENERS合金钢工具 ALLOY STEEL TOOLS螺栓模 BOLT HEA DING DIES手动拉钉钳 HAND RIVETER船舶链 ANCHOR CHAIN脚踏车链锁 BICYCLE CHAIN LOCKS螺丝起子 BIT罗拉 CHAIN ROLLER特殊铆合扣件 COLLARS(A BLINDFASTENER FOR HUCK INTL)装饰链 DECORATIVE CHAINS自攻螺纹衬套 ENSAT THREADED INSERTS六角扳手 HEXAGON KEYS超音螺纹压入式螺纹自动锁扣 THREADED INSERTS FOR PLASTIC INJECTION MOULDEINGS 汽车特殊杆接件 SPECIAL AUTO-MOBILE FASTENER AS YOUR NEEDS螺纹护套 RECOIL INSERTS链条用滚子 ROLLER FOR ROLLER CHAIN金属板镶嵌组件及自动夹扣组件 SHEET METAL FASTENERS工具套筒组件 SOCKET WRENCH SETS不锈钢链 STAINLESS STEEL CHAINS轭子 T-YOKE轮胎链 TIRE CHAINS狗链 DOG CHAINS喇叭头轭铁 U-YOKE,T-YOKE FOR SPEAKER不锈钢输送带轮用轨道 STAINLESS WHEEL'S RACK FOR TRANSPORTER 工业用链 INDUSTRIAL STEEL LINK CHAINS拖链安全链 TOW CHAINS AND SAFETY CHAINS机车离合器零件 MANUFACTURE OF MOTORCYCLE'S CVT PARTS牙条棒 THREAD ROD。

螺丝紧固件英文词汇机(踏)车用螺丝、轴心Screws And Shafts For Motorcycle Or Bicycle针车用螺丝、轴心Screws And Shafts For Sewing Maching止付螺丝Socket Set Screws不锈钢宽牙螺丝Stainless Steel Coarse Thread Screws不锈钢高低牙螺丝Stainless Steel High-Low Thread Screws不锈钢机械螺丝Stainless Steel Machine Screws不锈钢钻尾螺丝Stainless Steel Self Drilling Screws不锈钢自攻螺丝Stainless Steel Self Tapping Screws不锈钢自削螺丝Stainless Steel Thread Cutting Screws不锈钢三角牙螺丝Stainless Steel Tri-Lobular Thread Screws插片壁虎 Steel Ceiling Anchors内迫壁虎 Drop in Anchors碳钢锤钉壁虎 Steel Hit Anchors碳钢六角螺帽Steel Hex Coupling Nuts强力车修壁虎 Wedge Anchors外迫壁虎 Cut Anchors化学壁虎 Chemical Anchors不锈钢重载胀栓Heavy Duty Expansion Anchors鱼眼壁虎企眼长螺帽 Tie Wire Anchors锌合金打入式壁虎 Hammer Drive Anchors弹簧螺帽 Strut Nuts兰花夹系列Toggle Bolts (Spring Toggle & Gravity Toggle)门窗、地板专用壁虎Nylon Frame Anchors or Metalframe Anchors石膏板中空壁虎 Hollow Wall Anchors套管式壁虎 Sleeve Anchors打入式壁虎鱼形尼龙壁虎 Nylon Frame Harmmer Fixing (Nylon Hammer Drive Anchors)强力式锤钉壁虎 Hit Anchors电梯壁虎 Bolt Anchors重载壁虎Heavy duty anchors两片夹 Loxin Masonry Anchors定位螺栓 Set Bolts长型兰花夹 Short Strap Anchors工具棒Drop in Setting Tools象脚壁虎Elephant foot anchors水泥预埋件 Concrete Insert翻边胀轴Drop in Anchor with Lip冲件 Legs Drywall Anchors六角盖头螺帽Hex Cap Nuts六角锯齿螺帽Hex Serrated Nuts六角轮缘螺帽Hex Flange Nuts高脚螺帽Hex Coupling Nuts(High Nuts)圆螺帽 Round Nuts四角螺帽 Square Nuts管用螺帽 Pipe Nuts轮壳螺帽 Wheel Nuts蝶型螺帽 Wing NutsU形螺帽 U NutsT形螺帽 T Nuts环首螺帽 Eye Nuts齿形螺帽 Kep Nuts齿花螺帽 Clinch Nuts耐候钢六角重型螺帽Corten Steel Heavy Hex Nuts焊接螺帽 Weld Nuts高张力螺帽Heigh Strength Nuts建业用螺帽 Structural Nuts不锈钢螺帽 Stainless Steel Nuts铜螺帽 Brass Nuts铝螺帽 Aluminum Nuts合金钢螺帽 Alloy Steel Nuts重型车螺帽Heavy Duty Wheel Hub Nuts铁器焊接袋帽Acorn Cap Nuts金属预置扭矩式螺帽All-Metal Prevailing Torque Type Nuts壁虎螺帽 Anchor Nuts大尺寸螺帽Big Size Nuts铁盖袋帽Closed End Acorn Nuts盘形华司螺帽 Conical Washer Nuts铁盖+尼龙圈组合盖帽Din 986 Domed Cap Nuts突缘尼龙盖帽Flange Nylon Insert Lock Nuts平面华司螺帽Flat Waser Nuts六角割沟螺帽Hex Slotted Nut自锁螺帽 Self-Locking Nuts制止螺帽 Sliding NutsSln-自动防松螺帽Sln Self-Locking Nuts其它特殊螺帽 Special Nuts弹簧螺帽 Spring Nuts不锈钢突缘螺帽Stainless Steel Flange Nuts不锈钢六角轮缘尼龙螺帽Stainless Steel Flange Nylon Insert Lock Nuts不锈钢六角重型螺帽Stainless Steel Heavy Hex Nuts不锈钢六角螺帽Stainless Steel Hex Nuts不锈钢尼龙嵌入螺帽Stainless Steel Nylon Insert Lock Nuts 普通六角螺帽 Hex Nuts六角重型螺帽Heavy Hex Nuts薄型螺帽Hex Jam Nuts尼龙嵌入防松螺帽Nylon Insert Lock Nuts机械螺丝用六角螺帽Hex Machine Screw Nut六角螺丝(栓) Hex Head Cap Screws(Hex Bolts)六角机械螺丝Hex Head Machine Bolts六角木牙螺丝Hex Lag Bolts四角螺丝Square Head BoltsT头螺丝T Head Bolts马车螺丝 Carriage Bolts环首螺丝 Eye Bolts内六角孔螺丝Hex Socket Cap Screws固定螺丝 Set Screws螺椿栓 Stud Bolts螺旋椿 Screw Studs轮壳螺栓 Wheel Bolts翼形螺丝 Wing Screws自攻螺丝 Self Tapping Screws自削螺丝Thread Cutting Screws钻尾螺丝Self Drilling Screws旋入螺丝 Drive Screws机械螺丝 Machine Screws木螺丝 Wood Screws家具螺丝 Furniture Screws塑板螺丝 Chipboard Screws墙用螺丝 Drywall Screws基础螺栓 Foundation BoltsU型螺栓 U Bolts勾头螺栓 Hook Bolts套挂螺丝 Toggle Bolts突缘螺丝 Flange Bolts轨道螺栓(鱼尾螺丝) Track Bolts耐候钢螺丝Corten Steel Heavy Hex Bolts扭矩控制螺栓 T.C.Bolts高张力螺栓 High Strength Bolts剪力钉(焊接螺丝) Welding Studs螺丝附华司组合Screws And Washers Assembled(Sems) 大尺寸螺栓Big Size Bolts不锈钢小螺丝Stainless Steel Sheet Metal Screws不锈钢大螺丝Stainless Steel Bolts铜螺丝 Brass Screws铝螺丝 Aluminum Screws合金钢螺丝 Alloy Steel Screws电子螺丝 Electronic Screws微小精密螺丝 Micro Screws塑料螺丝 Plastic Screws复合材料用螺丝Particle Board Screws钛合金螺丝 Titanium Alloy Bolts钛、锆、钼、铌等螺丝、零件、材料Ti,Zr,Mo,Nb Pare Metal Bolts Parts 拇指螺丝 Thumb Screws双头牙螺丝Double End Screws Hanger Bolt车辆(汽车)螺丝、螺帽 Automotive Fasteners航天用螺丝 Aerospace Fasteners飞机特殊扣件Source Control Bolts拉栓 Blind Bolts面板螺丝 Panel Fasteners电梯螺丝 Elevator Bolts四角头固定螺丝Square Set Screws大头马车螺丝 Step Bolts单向螺丝One Way Lag Screws管夹螺丝Hose Clamp Screws不锈钢固定螺丝Stainless Steel Hex Socket Cap Screws不锈钢内六角螺丝Stainless Steel Hex Socket Cap Screws铰链螺丝 Hinge Screws货柜螺丝 Container Screws复合材料钻尾螺丝Bi-Metal Self Drilling Screws三角牙螺丝 Trilobular Thread Screws高低牙螺丝High Low Screws夹板用螺丝Particle Board Screws马桶螺丝Toilet Closet Bolts特长螺丝Special Longer Screws建业螺丝 Building Fasteners不锈钢六角螺丝Stainless Steel Hex Socket Cap Screws其它特殊螺丝 Special Screws Or Bolts不锈钢特殊螺丝Special Stainless Steel Screws宽牙螺丝（粗牙螺丝） Coarse Thread Screws链带螺丝 Collated Screws水泥螺丝 Concrete Screws板模螺丝 Construction Bolts锌蝶螺丝Die Cast Wing Screws; Zinc Alloy重型车螺丝Heavy Duty Wheel Hub Bolts内六角固定螺丝Hex Socket Set Screws复合材料用螺丝（夹板用）Particle Board Screws犁壁螺丝 Plow Bolts不锈钢木螺丝Stainless Steel Wood Screws套挂螺栓及螺丝 Toggle Bolts钛合金膨胀螺丝Titanium Alloy Expansion Bolts六角盖头螺帽Hex Cap Nuts六角锯齿螺帽Hex Serrated Nuts六角轮缘螺帽Hex Flange Nuts高脚螺帽Hex Coupling Nuts(High Nuts)圆螺帽 Round Nuts四角螺帽 Square Nuts管用螺帽 Pipe Nuts轮壳螺帽 Wheel Nuts蝶型螺帽 Wing NutsU形螺帽 U NutsT形螺帽 T Nuts环首螺帽 Eye Nuts齿形螺帽 Kep Nuts齿花螺帽 Clinch Nuts耐候钢六角重型螺帽Corten Steel Heavy Hex Nuts焊接螺帽 Weld Nuts高张力螺帽Heigh Strength Nuts建业用螺帽 Structural Nuts不锈钢螺帽 Stainless Steel Nuts铜螺帽 Brass Nuts铝螺帽 Aluminum Nuts合金钢螺帽 Alloy Steel Nuts重型车螺帽Heavy Duty Wheel Hub Nuts铁器焊接袋帽Acorn Cap Nuts金属预置扭矩式螺帽All-Metal Prevailing Torque Type Nuts 壁虎螺帽 Anchor Nuts大尺寸螺帽Big Size Nuts铁盖袋帽Closed End Acorn Nuts盘形华司螺帽 Conical Washer Nuts铁盖+尼龙圈组合盖帽Din 986 Domed Cap Nuts突缘尼龙盖帽Flange Nylon Insert Lock Nuts平面华司螺帽Flat Waser Nuts六角割沟螺帽Hex Slotted Nut自锁螺帽 Self-Locking Nuts制止螺帽 Sliding NutsSln-自动防松螺帽Sln Self-Locking Nuts其它特殊螺帽 Special Nuts弹簧螺帽 Spring Nuts不锈钢突缘螺帽Stainless Steel Flange Nuts不锈钢六角轮缘尼龙螺帽Stainless Steel Flange Nylon Insert Lock Nuts不锈钢六角重型螺帽Stainless Steel Heavy Hex Nuts不锈钢六角螺帽Stainless Steel Hex Nuts不锈钢尼龙嵌入螺帽Stainless Steel Nylon Insert Lock Nuts锌压属螺帽Zinc Die Casting Nuts普通六角螺帽 Hex Nuts六角重型螺帽Heavy Hex Nuts薄型螺帽Hex Jam Nuts尼龙嵌入防松螺帽Nylon Insert Lock Nuts机械螺丝用六角螺帽Hex Machine Screw Nut合金钢线材盘元Alloy Steel Wire Rod球状化线材Annealing Wire And Rod黑铁丝 Black Wire黄铜棒线Brass Wire And Rod磨光棒钢Bright Steel Bar(Hex/Round/Square)铜合金线 Copper Alloy Wire线切割线 E.D.M Cutting Wire快削钢线材盘元Free Cutting Steel Wire Rod线材Iron Or Steel Wire线材盘元Iron Or Steel Wire Rod洋白铜线Nickel Silver Wire磷青铜线Phosphate Bronze Wire不锈钢条棒 Stainless Steel Bar(Round/Hex/Square)不锈钢冷锻线材Stainless Steel Cold Heading Wire不锈钢线(抽线后) Stainless Steel Draw Wire不锈钢线材 Stainless Steel Wire不锈钢线材及盘元Stainless Steel Wire And Rod棒钢 Steel Bar(Hex/Round/Square)转回90度碾线头机 90讧evolving Wire Twisting Machine气动拉钉机 Air Riveter各式螺丝类产品自动包装Automatic Packaging For All Kinds Of Packaging 自动包装机Automatic Packing Machine螺丝制造搓牙机械Automatic Thread Rolling Machine螺丝割尾加工机械Automatic Thread Slotting Machine螺丝制造成型机械 Automatic Trimming Machine拉钉打头机Blind Rivet Heading Machine螺丝、螺帽成型机Bolt Formers,Nuts Formers,Headers螺丝、螺帽热处理Bolt Nut And Screws Heat Treatment螺丝、螺帽热处理炉Bolt Nut And Screws Heat Treatment Furnaces球状化电器炖炉Carburizing Furnace Vacuum And Bell Type Furnace超防锈复合瓷膜 Ceramic Coating连续式光辉渗碳淬火炉Continuous Bright Carburizing Quenching Furnace连续式光辉调质淬火炉Continuous Bright Hardening Quenching Furnace中、高热镀锌光辉连续炉 Continuous Bright Heat Treat Furnace连续式光辉热处理炉Continuous Type Bright Heat Treatment Furnace螺丝割尾及特殊割遘加工Machine Screw Shank Slotting螺丝钻孔加工Screw Shank Drilling鸡眼上下模 Eyelets Dies一般线材、盘元、退火炉 General Wire,Wire Rod,Annealing Furnace倒立式滑落型伸线机Handstand Type Wire Drawing Machine十字冲模Header Punches In Various Drives成型冲模Header Punches In Various Drives螺丝打头机 Heading Machine螺丝制造高速搓牙机械High Speed Automatic Thread Rolling Machine高中低周波感应加热炉 High,Medium,Low Frequency Induction Heater空心打头机Hollow Heading Machine热浸镀锌螺丝、螺帽Hot Dip Galvanizing Bolts And Nuts机械镀锌 Mechanical Galvanized迷你成型机 Mini-Formers成品自动收线机 Non-Stop Coiler精抽自动收线机 Non-Stop Coiler(Skinpass)螺帽模Nut Forming Dies螺帽成型模 Nuts Formers特殊零件成型机 Parts Forming Maching冲模 Punch Dies冲子 Punch Pins罗拉成型机 Rollers Formers机(踏)车用螺丝成型机Screw For Motorcycle Or Bicycle Heading Machine止付螺丝成型机Set Screws Formers套高成型机 Sockets Formers一般线材、盘元、螺丝合金炖炉Spheroidizing Bright Annealing Furnace球状化热处理炉Spheroidizing Heat Treatment Furnace攻牙机 Tapping Machine螺丝攻、车刀、模具 Taps Dies And Tools搓牙机铁屑分离装置Thread Chip Separator滚牙轮Thread Rolling Dies牙板Thread Rolling Dies Plates精密油压滚牙机Hydraulic Thread Rolling Machines模具 Tools六角整头模 Trimming Dies Hexagan碳化钨模具Tungsten Carbide Die镀钛处理(Tin)专业加工服务Tin Hard Coating For Cutting Tools And Punch By Pvd电镀化学原料 Various Electroplating Chemicals环规校正Calibration For Ring Gage环规、牙规、三线规校正 Calibration For Ring Gage, Athread Gage, 3 Wire Gage螺丝、螺帽品检量测仪器Fasteners Inspection And Measurement Instruments 螺丝、螺帽成型攻牙专用油 Forming And Tapping Oils For Bolts And Nuts Formers螺丝、螺帽五金等检验Insptection Services For Fasteners And Hardware德国schatz扭力机代理Representative Of Schatz Torque MachinIso品质保证系统 Iso Quality Assurance System生产管理系统 Production Control System物料管理系统Material Control System齿轮 Gears不锈钢牙条棒Stainless Steel Hread Rod马达轴承轴心组件 Bearing Shaft(Motor)轴承轴心 Bearing Shaft开口铆钉 Blind Rivets长形拉帽Blind Rivet Nuts拉帽 Blind Nuts拉钉 Blind Rivets实心梢Clevis Pins And Straight Pins弹片 Clips卷钉 Coil Nails冷锻零件Cold Forming Part开口销 Cotter PinsE型环 E-Rings膨胀螺栓 Expansion Anchor Bolts鸡眼钉 Eyelets RivetsR型销 Snap Pins闸、锁Latches And Keeper Assembleds其它特殊铆钉Other Specil Rivets销 Pins格式管夹、管束 Pipe Hanger铆钉 Rivets螺旋锔及螺旋圈Screw Hook And Screw Rings中空钉 Semi-Tubular Rivet开叉钉 Split Drive Anchors弹簧华司 Spring Washers弹簧蝴蝶夹 Spring Wings不锈钢华司 Stainlesssteel Washers钢铁钉Steel And Iron Nails搓牙铁钉 Thread Nails钛合金铆钉 Titaium Alloy Rivets管形铆钉 Tubular Rivets华司 Washers真空热处理 Vacuum Heat Treatment螺丝、螺帽、五金、Diy扣件 Fasteners合金钢工具 Alloy Steel Tools螺栓模 Bolt Heading Dies手动拉钉钳 Hand Riveter船舶链 Anchor Chain脚踏车链锁Bicycle Chain Locks螺丝起子 Bit罗拉 Chain Roller特殊铆合扣件Collars(A Blindfastener For Huck Intl)装饰链 Decorative Chains自攻螺纹衬套 Ensat Threaded Inserts六角扳手 Hexagon Keys超音螺纹压入式螺纹自动锁扣 Threaded Inserts For Plastic Injection Mouldeings汽车特殊杆接件Special Auto-Mobile Fastener As Your Needs螺纹护套 Recoil Inserts链条用滚子Roller For Roller Chain金属板镶嵌组件及自动夹扣组件Sheet Metal Fasteners工具套筒组件Socket Wrench Sets不锈钢链Stainless Steel Chains轭子 T-Yoke轮胎链 Tire Chains狗链 Dog Chains喇叭头轭铁U-Yoke,T-Yoke For Speaker不锈钢输送带轮用轨道Stainless Wheel's Rack For Transporter工业用链Industrial Steel Link Chains拖链安全链Tow Chains And Safety Chains机车离合器零件Manufacture Of Motorcycle's Cvt Parts牙条棒 Thread Rod。

家具配件常用到的英文单词AAluminum 铝BBall bearing slide脚轮滑道Bolt pin 螺栓插销Bolts and nuts for furniture 家具用螺钉/螺帽Brass 铜CCarcase 框架，架子Castor 小脚轮Ceiling 天花板Central hinges 中央铰链Chrome 铬Complete range of drawer slide 各种类型的抽屉滑道Component 零配件，元件Concealed hinge 内藏铰链Cupboard-lock 拒门锁DDecorative trims for furniture 家具金边饰条Door & window 门窗Drawer-lock 抽屉锁Drawer runner 抽屉滑槽EEquipment for surface treatment 表面处理工具3/4 extension slide 部分开式滑道FFaucet 水龙头Fixture 固定装置Full extension slide 全开式滑道Furniture fittings 家具五金Furniture hardware家具五金Furniture parts 家具零配件Furniture structural parts 家具结构零件GGas lift chassis 气压棒底盘Glass door hinge 玻璃门铰链HHeavy duty slide 承重式滑道Hook lock 钩锁KKeyboard slide 键盘板滑道LLarge head type 大头型Locating dowel 定位榫钉Lock rail 安锁冒头MMagnetic catch 磁性拉手 Magnetic-lock 磁锁magnetic push latch磁性撞锁Marquetry work镶嵌装饰品Material 原材料Metal fittings 金属配件Matal handle 金属拉手Mold模具OOffice chair central tube accessories 办公椅中管配件Office chair hardware accessories 办公椅五金配件Out set 外盖型套轮PPanel veneer 板料Plastic 塑料Plastic bolt and threaded axis 塑料螺帽及牙轴Pocket door slide 柜门滑道Prevent falling off due to turning防止旋转脱落SSecret-hinge 暗铰Semifinished furniture product andaccessories 家具半成品及配件Semifinished product for interior fittings装潢用半成品Simple connecting fittings 简单五金配件Single item 单项产品Sliding door roller series 推拉门用轮系列Straight-lock 企口锁Surface gluing 板面上胶VVeneer trimming 薄片整修Vertical upright 直挂格WWood-button 木纽 Wood components 木制配件 Wooden bar 车件 Wooden cork 木塞 Wooden curtain rod and ring 木制窗帘杆及吊环 Woodscrew 木螺钉 Wreathed hand-rail 扭弯扶手本文转载自:家具论坛。

紧固件英语单词(2008-12-16 22:40:33)中文名称英文名称六角螺丝(栓) HEX HEAD CAP SCREWS(HEX BOLTS)六角机械螺丝HEX HEAD MACHINE BOLTS六角木牙螺丝HEX LAG BOLTS四角螺丝SQUARE HEAD BOLTST头螺丝T HEAD BOLTS马车螺丝CARRIAGE BOLTS环首螺丝EYE BOLTS内六角孔螺丝HEX SOCKET CAP SCREWS固定螺丝SET SCREWS螺椿栓STUD BOLTS螺旋椿SCREW STUDS轮壳螺栓WHEEL BOLTS翼形螺丝WING SCREWS自攻螺丝SELF TAPPING SCREWS自削螺丝THREAD CUTTING SCREWS钻尾螺丝SELF DRILLING SCREWS旋入螺丝DRIVE SCREWS机械螺丝MACHINE SCREWS木螺丝WOOD SCREWS家具螺丝FURNITURE SCREWS塑板螺丝CHIPBOARD SCREWS墙用螺丝DRYWALL SCREWS基础螺栓FOUNDA TION BOLTSU型螺栓U BOLTS勾头螺栓HOOK BOLTS套挂螺丝TOGGLE BOLTS突缘螺丝FLANGE BOLTS轨道螺栓(鱼尾螺丝) TRACK BOLTS耐候钢螺丝CORTEN STEEL HEA VY HEX BOLTS扭矩控制螺栓T.C.BOLTS高张力螺栓HIGH STRENGTH BOLTS剪力钉(焊接螺丝) WELDING STUDS螺丝附华司组合SCREWS AND WASHERS ASSEMBLED(SEMS)大尺寸螺栓BIG SIZE BOLTS不锈钢小螺丝STAINLESS STEEL SHEET METAL SCREWS不锈钢大螺丝STAINLESS STEEL BOLTS铜螺丝BRASS SCREWS铝螺丝ALUMINUM SCREWS合金钢螺丝ALLOY STEEL SCREWS电子螺丝ELECTRONIC SCREWS微小精密螺丝MICRO SCREWS塑料螺丝PLASTIC SCREWS复合材料用螺丝PARTICLE BOARD SCREWS钛合金螺丝TITANIUM ALLOY BOLTS钛、锆、钼、铌等螺丝、零件、材料TI,ZR,MO,NB PARE METAL BOLTS PARTS 拇指螺丝THUMB SCREWS双头牙螺丝DOUBLE END SCREWS HANGER BOLT车辆(汽车)螺丝、螺帽AUTOMOTIVE FASTENERS航天用螺丝AEROSPACE FASTENERS飞机特殊扣件SOURCE CONTROL BOLTS拉栓BLIND BOLTS面板螺丝PANEL FASTENERS电梯螺丝ELEV A TOR BOLTS四角头固定螺丝SQUARE SET SCREWS大头马车螺丝STEP BOLTS单向螺丝ONE W AY LAG SCREWS管夹螺丝HOSE CLAMP SCREWS不锈钢固定螺丝STAINLESS STEEL HEX SOCKET CAP SCREWS不锈钢内六角螺丝STAINLESS STEEL HEX SOCKET CAP SCREWS铰链螺丝HINGE SCREWS货柜螺丝CONTAINER SCREWS复合材料钻尾螺丝BI-METAL SELF DRILLING SCREWS三角牙螺丝TRILOBULAR THREAD SCREWS高低牙螺丝HIGH LOW SCREWS夹板用螺丝PARTICLE BOARD SCREWS马桶螺丝TOILET CLOSET BOLTS特长螺丝SPECIAL LONGER SCREWS建业螺丝BUILDING FASTENERS不锈钢六角螺丝STAINLESS STEEL HEX SOCKET CAP SCREWS其它特殊螺丝SPECIAL SCREWS OR BOLTS不锈钢特殊螺丝SPECIAL STAINLESS STEEL SCREWS宽牙螺丝（粗牙螺丝）COARSE THREAD SCREWS链带螺丝COLLA TED SCREWS水泥螺丝CONCRETE SCREWS板模螺丝CONSTRUCTION BOLTS锌蝶螺丝DIE CAST WING SCREWS; ZINC ALLOY重型车螺丝HEA VY DUTY WHEEL HUB BOLTS内六角固定螺丝HEX SOCKET SET SCREWS复合材料用螺丝（夹板用）PARTICLE BOARD SCREWS犁壁螺丝PLOW BOLTS机(踏)车用螺丝、轴心SCREWS AND SHAFTS FOR MOTORCYCLE OR BICYCLE 针车用螺丝、轴心SCREWS AND SHAFTS FOR SEWING MACHING止付螺丝SOCKET SET SCREWS不锈钢宽牙螺丝STAINLESS STEEL COARSE THREAD SCREWS不锈钢高低牙螺丝STAINLESS STEEL HIGH-LOW THREAD SCREWS不锈钢机械螺丝STAINLESS STEEL MACHINE SCREWS不锈钢钻尾螺丝STAINLESS STEEL SELF DRILLING SCREWS不锈钢自攻螺丝STAINLESS STEEL SELF TAPPING SCREWS不锈钢自削螺丝STAINLESS STEEL THREAD CUTTING SCREWS不锈钢三角牙螺丝STAINLESS STEEL TRI-LOBULAR THREAD SCREWS 不锈钢木螺丝STAINLESS STEEL WOOD SCREWS套挂螺栓及螺丝TOGGLE BOLTS钛合金膨胀螺丝TITANIUM ALLOY EXPANSION BOLTS中文名称英文名称六角盖头螺帽HEX CAP NUTS六角锯齿螺帽HEX SERRA TED NUTS六角轮缘螺帽HEX FLANGE NUTS高脚螺帽HEX COUPLING NUTS(HIGH NUTS)圆螺帽ROUND NUTS四角螺帽SQUARE NUTS管用螺帽PIPE NUTS轮壳螺帽WHEEL NUTS蝶型螺帽WING NUTSU形螺帽U NUTST形螺帽T NUTS环首螺帽EYE NUTS齿形螺帽KEP NUTS齿花螺帽CLINCH NUTS耐候钢六角重型螺帽CORTEN STEEL HEA VY HEX NUTS焊接螺帽WELD NUTS高张力螺帽HEIGH STRENGTH NUTS建业用螺帽STRUCTURAL NUTS不锈钢螺帽STAINLESS STEEL NUTS铜螺帽BRASS NUTS铝螺帽ALUMINUM NUTS合金钢螺帽ALLOY STEEL NUTS重型车螺帽HEA VY DUTY WHEEL HUB NUTS铁器焊接袋帽ACORN CAP NUTS金属预置扭矩式螺帽ALL-METAL PREV AILING TORQUE TYPE NUTS壁虎螺帽ANCHOR NUTS大尺寸螺帽BIG SIZE NUTS铁盖袋帽CLOSED END ACORN NUTS盘形华司螺帽CONICAL WASHER NUTS铁盖+尼龙圈组合盖帽DIN 986 DOMED CAP NUTS突缘尼龙盖帽FLANGE NYLON INSERT LOCK NUTS平面华司螺帽FLA T W ASER NUTS六角割沟螺帽HEX SLOTTED NUT自锁螺帽SELF-LOCKING NUTS制止螺帽SLIDING NUTSSLN-自动防松螺帽SLN SELF-LOCKING NUTS其它特殊螺帽SPECIAL NUTS弹簧螺帽SPRING NUTS不锈钢突缘螺帽STAINLESS STEEL FLANGE NUTS不锈钢六角轮缘尼龙螺帽STAINLESS STEEL FLANGE NYLON INSERT LOCK NUTS不锈钢六角重型螺帽STAINLESS STEEL HEA VY HEX NUTS不锈钢六角螺帽STAINLESS STEEL HEX NUTS不锈钢尼龙嵌入螺帽STAINLESS STEEL NYLON INSERT LOCK NUTS锌压属螺帽ZINC DIE CASTING NUTS普通六角螺帽HEX NUTS六角重型螺帽HEA VY HEX NUTS薄型螺帽HEX JAM NUTS尼龙嵌入防松螺帽NYLON INSERT LOCK NUTS机械螺丝用六角螺帽HEX MACHINE SCREW NUT中文名称英文名称合金钢线材盘元ALLOY STEEL WIRE ROD球状化线材ANNEALING WIRE AND ROD黑铁丝BLACK WIRE黄铜棒线BRASS WIRE AND ROD磨光棒钢BRIGHT STEEL BAR(HEX/ROUND/SQUARE)铜合金线COPPER ALLOY WIRE线切割线 E.D.M CUTTING WIRE快削钢线材盘元FREE CUTTING STEEL WIRE ROD线材IRON OR STEEL WIRE线材盘元IRON OR STEEL WIRE ROD洋白铜线NICKEL SILVER WIRE磷青铜线PHOSPHA TE BRONZE WIRE不锈钢条棒STAINLESS STEEL BAR(ROUND/HEX/SQUARE)不锈钢冷锻线材STAINLESS STEEL COLD HEADING WIRE不锈钢线(抽线后) STAINLESS STEEL DRA W WIRE不锈钢线材STAINLESS STEEL WIRE不锈钢线材及盘元STAINLESS STEEL WIRE AND ROD棒钢STEEL BAR(HEX/ROUND/SQUARE)转回90度碾线头机90讧EVOLVING WIRE TWISTING MACHINE气动拉钉机AIR RIVETER各式螺丝类产品自动包装AUTOMA TIC PACKAGING FOR ALL KINDS OF PACKAGING 自动包装机AUTOMA TIC PACKING MACHINE螺丝制造搓牙机械AUTOMA TIC THREAD ROLLING MACHINE螺丝割尾加工机械AUTOMA TIC THREAD SLOTTING MACHINE螺丝制造成型机械AUTOMA TIC TRIMMING MACHINE拉钉打头机BLIND RIVET HEADING MACHINE螺丝、螺帽成型机BOLT FORMERS,NUTS FORMERS,HEADERS螺丝、螺帽热处理BOLT NUT AND SCREWS HEA T TREA TMENT螺丝、螺帽热处理炉BOLT NUT AND SCREWS HEA T TREA TMENT FURNACES球状化电器炖炉CARBURIZING FURNACE V ACUUM AND BELL TYPE FURNACE超防锈复合瓷膜CERAMIC COA TING连续式光辉渗碳淬火炉CONTINUOUS BRIGHT CARBURIZING QUENCHING FURNACE 连续式光辉调质淬火炉CONTINUOUS BRIGHT HARDENING QUENCHING FURNACE 中、高热镀锌光辉连续炉CONTINUOUS BRIGHT HEA T TREA T FURNACE连续式光辉热处理炉CONTINUOUS TYPE BRIGHT HEA T TREA TMENT FURNACE螺丝割尾及特殊割遘加工MACHINE SCREW SHANK SLOTTING螺丝钻孔加工SCREW SHANK DRILLING鸡眼上下模EYELETS DIES一般线材、盘元、退火炉GENERAL WIRE,WIRE ROD,ANNEALING FURNACE倒立式滑落型伸线机HANDSTAND TYPE WIRE DRAWING MACHINE十字冲模HEADER PUNCHES IN V ARIOUS DRIVES成型冲模HEADER PUNCHES IN V ARIOUS DRIVES螺丝打头机HEADING MACHINE螺丝制造高速搓牙机械HIGH SPEED AUTOMA TIC THREAD ROLLING MACHINE高中低周波感应加热炉HIGH,MEDIUM,LOW FREQUENCY INDUCTION HEA TER空心打头机HOLLOW HEADING MACHINE热浸镀锌螺丝、螺帽HOT DIP GALV ANIZING BOLTS AND NUTS机械镀锌MECHANICAL GALV ANIZED迷你成型机MINI-FORMERS成品自动收线机NON-STOP COILER精抽自动收线机NON-STOP COILER(SKINPASS)螺帽模NUT FORMING DIES螺帽成型模NUTS FORMERS特殊零件成型机PARTS FORMING MACHING冲模PUNCH DIES冲子PUNCH PINS罗拉成型机ROLLERS FORMERS机(踏)车用螺丝成型机SCREW FOR MOTORCYCLE OR BICYCLE HEADING MACHINE 止付螺丝成型机SET SCREWS FORMERS套高成型机SOCKETS FORMERS一般线材、盘元、螺丝合金炖炉SPHEROIDIZING BRIGHT ANNEALING FURNACE球状化热处理炉SPHEROIDIZING HEA T TREA TMENT FURNACE攻牙机TAPPING MACHINE螺丝攻、车刀、模具TAPS DIES AND TOOLS搓牙机铁屑分离装置THREAD CHIP SEPARA TOR滚牙轮THREAD ROLLING DIES牙板THREAD ROLLING DIES PLA TES精密油压滚牙机HYDRAULIC THREAD ROLLING MACHINES模具TOOLS六角整头模TRIMMING DIES HEXAGAN碳化钨模具TUNGSTEN CARBIDE DIE镀钛处理(TiN)专业加工服务TiN HARD COA TING FOR CUTTING TOOLS AND PUNCHBY PVD电镀化学原料V ARIOUS ELECTROPLA TING CHEMICALS环规校正CALIBRA TION FOR RING GAGE环规、牙规、三线规校正CALIBRA TION FOR RING GAGE, A THREAD GAGE, 3 WIREGAGE螺丝、螺帽品检量测仪器FASTENERS INSPECTION AND MEASUREMENT INSTRUMENTS螺丝、螺帽成型攻牙专用油FORMING AND TAPPING OILS FOR BOLTS AND NUTS FORMERS螺丝、螺帽五金等检验INSPTECTION SERVICES FOR FASTENERS AND HARDWARE德国SCHA TZ扭力机代理REPRESENTA TIVE OF SCHA TZ TORQUE MACHINISO质量保证系统ISO QUALITY ASSURANCE SYSTEM生产管理系统PRODUCTION CONTROL SYSTEM物料管理系统MA TERIAL CONTROL SYSTEM中文名称英文名称齿轮GEARS不锈钢牙条棒STAINLESS STEEL HREAD ROD马达轴承轴心组件BEARING SHAFT(MOTOR)轴承轴心BEARING SHAFT开口铆钉BLIND RIVETS长形拉帽BLIND RIVET NUTS拉帽BLIND NUTS拉钉BLIND RIVETS实心梢CLEVIS PINS AND STRAIGHT PINS弹片CLIPS卷钉COIL NAILS冷锻零件COLD FORMING PART开口销COTTER PINSE型环E-RINGS膨胀螺栓EXPANSION ANCHOR BOLTS鸡眼钉EYELETS RIVETSR型销SNAP PINS闸、锁LA TCHES AND KEEPER ASSEMBLEDS其它特殊铆钉OTHER SPECIL RIVETS销PINS格式管夹、管束PIPE HANGER铆钉RIVETS螺旋锔及螺旋圈SCREW HOOK AND SCREW RINGS中空钉SEMI-TUBULAR RIVET开叉钉SPLIT DRIVE ANCHORS弹簧华司SPRING W ASHERS弹簧蝴蝶夹SPRING WINGS不锈钢华司STAINLESSSTEEL WASHERS钢铁钉STEEL AND IRON NAILS搓牙铁钉THREAD NAILS钛合金铆钉TITAIUM ALLOY RIVETS管形铆钉TUBULAR RIVETS华司W ASHERS真空热处理V ACUUM HEA T TREA TMENT螺丝、螺帽、五金、DIY扣件FASTENERS合金钢工具ALLOY STEEL TOOLS螺栓模BOLT HEADING DIES手动拉钉钳HAND RIVETER船舶链ANCHOR CHAIN脚踏车链锁BICYCLE CHAIN LOCKS螺丝起子BIT罗拉CHAIN ROLLER特殊铆合扣件COLLARS(A BLINDFASTENER FOR HUCK INTL)装饰链DECORA TIVE CHAINS自攻螺纹衬套ENSA T THREADED INSERTS六角扳手HEXAGON KEYS超音螺纹压入式螺纹自动锁扣THREADED INSERTS FOR PLASTIC INJECTION MOULDEINGS汽车特殊杆接件SPECIAL AUTO-MOBILE FASTENER AS YOUR NEEDS螺纹护套RECOIL INSERTS链条用滚子ROLLER FOR ROLLER CHAIN金属板镶嵌组件及自动夹扣组件SHEET METAL FASTENERS工具套筒组件SOCKET WRENCH SETS不锈钢链STAINLESS STEEL CHAINS轭子T-YOKE轮胎链TIRE CHAINS狗链DOG CHAINS喇叭头轭铁U-YOKE,T-YOKE FOR SPEAKER不锈钢输送带轮用轨道STAINLESS WHEEL＇S RACK FOR TRANSPORTER工业用链INDUSTRIAL STEEL LINK CHAINS拖链安全链TOW CHAINS AND SAFETY CHAINS机车离合器零件MANUFACTURE OF MOTORCYCLE＇S CVT PARTS牙条棒THREAD ROD。

常用英文单词及简写形式No. 单词简写中文1 screw scr 螺丝2 nut nut 螺母3 washer wash 垫圈4 head hd 头5 thread thre 螺纹6 coating coat 镀层7 rivet riv 铆钉8 standoff stdoff 内外六角钉9 driver driv 穴10 hexagon hexa 六角11 tooth tooth 齿12 lock lck 锁13 spring spr 弹簧14 wave wave 波浪型15 pitch pitch 牙距16 partial thread P T 半螺纹17 PT PT 一种螺纹形式18 Full Thread FT 全螺纹19 silver silv 银20 cone cone 锥形21 Eco-syn Eco 30度牙的一种螺纹22 Thread Forming TF 自攻螺纹23 Self Tapping self tapp 自切屑螺纹24 pin pin 销25 shaft Shaf 轴26 steel St 铁27 stainless steel SS 不锈钢28 Brass(Cu) Bras(Cu) 铜29 Aluminum AL 铝30 Rubber Rub 橡胶31 machine screw mech scr 机制螺丝32 SEM screw SEM Scr 组合螺丝33 Material material 材料34 Grade GD 等级35 Finish Finish 表面处理36 Point Point 点37 Clamp Clam 夹子38 internal Int 内39 external ext 外40 thickness / 厚度41 length / 长度42 hole / 孔43 Metric Metcric 公制44 DIN / 德标45 ANSI / 美标46 JIS / 日标47 ISO / 国际标准48 NFE / 法标49 GB / 国家标准50 Quality / 质量51 surface hardness 表面硬度52 product treatment 表面处理53 plating 电镀54 heat 热55 Screws And Shafts For Motorcycle Or Bicycle 机(踏)车用螺丝、轴心56 Screws And Shafts For Sewing Maching 针车用螺丝、轴心57 Socket Set Screws 止付螺丝58 Stainless Steel Coarse Thread Screws 不锈钢宽牙螺丝59 Stainless Steel High-Low Thread Screws 不锈钢高低牙螺丝60 Stainless Steel Machine Screws 不锈钢机械螺丝61 Stainless Steel Self Drilling Screws 不锈钢钻尾螺丝62 Stainless Steel Self Tapping Screws 不锈钢螺丝class=a1>自攻螺丝63 Stainless Steel Thread Cutting Screws 不锈钢自削螺丝64 Stainless Steel Tri-Lobular Thread Screws 不锈钢三角牙螺丝65 Steel Ceiling Anchors 插片壁虎66 Drop in Anchors 内迫壁虎67 Steel Hit Anchors 碳钢锤钉壁虎68 Steel Hex Coupling Nuts 碳钢六角螺帽69 Wedge Anchors 强力车修壁虎70 Cut Anchors 外迫壁虎71 Chemical Anchors 化学壁虎72 Heavy Duty Expansion Anchors 不锈钢重载胀栓73 Tie Wire Anchors 鱼眼壁虎企眼长螺帽74 Hammer Drive Anchors 锌合金打入式壁虎75 Strut Nuts 弹簧螺帽76 Toggle Bolts (Spring Toggle & Gravity Toggle) 兰花夹系列77 Nylon Frame Anchors or Metalframe Anchors 门窗、地板专用壁虎78 Hollow Wall Anchors 石膏板中空壁虎79 Sleeve Anchors 套管式壁虎80 Nylon Frame Harmmer Fixing (Nylon Hammer Drive Anchors) 打入式壁虎鱼形尼龙壁虎81 Hit Anchors 强力式锤钉壁虎82 Bolt Anchors 电梯壁虎83 Heavy duty anchors 重载壁虎84 Loxin Masonry Anchors 两片夹85 Set Bolts 定位螺栓86 Short Strap Anchors 长型兰花夹87 Drop in Setting Tools 工具棒88 Elephant foot anchors 象脚壁虎89 Concrete Insert 水泥预埋件90 Drop in Anchor with Lip 翻边胀轴91 Legs Drywall Anchors 冲件92 Hex Cap Nuts 六角盖头螺帽93 Hex Serrated Nuts 六角锯齿螺帽94 Hex Flange Nuts 六角轮缘螺帽95 Hex Coupling Nuts(High Nuts) 高脚螺帽96 Round Nuts 圆螺帽97 Square Nuts 四角螺帽98 Pipe Nuts 管用螺帽99 Wheel Nuts 轮壳螺帽100 Wing Nuts 蝶型螺帽101 U Nuts U形螺帽102 T Nuts T形螺帽103 Eye Nuts 环首螺帽104 Kep Nuts 齿形螺帽105 Clinch Nuts 齿花螺帽106 Corten Steel Heavy Hex Nuts 耐候钢六角重型螺帽107 Weld Nuts 焊接螺帽108 Heigh Strength Nuts 高张力螺帽109 Structural Nuts 建业用螺帽110 Stainless Steel Nuts 不锈钢螺帽111 Brass Nuts 铜螺帽112 Aluminum Nuts 铝螺帽113 Alloy Steel Nuts 合金钢螺帽114 Heavy Duty Wheel Hub Nuts 重型车螺帽115 Acorn Cap Nuts 铁器焊接袋帽116 All-Metal Prevailing Torque Type Nuts 金属预置扭矩式螺帽117 Anchor Nuts 壁虎螺帽118 Big Size Nuts 大尺寸螺帽119 Closed End Acorn Nuts 铁盖袋帽120 Conical Washer Nuts 盘形华司螺帽121 Din 986 Domed Cap Nuts 铁盖+尼龙圈组合盖帽122 Flange Nylon Insert Lock Nuts 突缘尼龙盖帽123 Flat Waser Nuts 平面华司螺帽124 Hex Slotted Nut 六角割沟螺帽125 Self-Locking Nuts 自锁螺帽126 Sliding Nuts 制止螺帽127 Sln Self-Locking Nuts Sln-自动防松螺帽128 Special Nuts 其它特殊螺帽129 Spring Nuts 弹簧螺帽130 Stainless Steel Flange Nuts 不锈钢突缘螺帽131 Stainless Steel Flange Nylon Insert Lock Nuts 不锈钢六角轮缘尼龙螺帽132 Stainless Steel Heavy Hex Nuts 不锈钢六角重型螺帽133 Stainless Steel Hex Nuts 不锈钢六角螺帽134 Stainless Steel Nylon Insert Lock Nuts 不锈钢尼龙嵌入螺帽135 Hex Nuts 普通六角螺帽136 Heavy Hex Nuts 六角重型螺帽137 Hex Jam Nuts 薄型螺帽138 Nylon Insert Lock Nuts 尼龙嵌入防松螺帽139 Hex Machine Screw Nut 机械螺丝用六角螺帽140 Hex Head Cap Screws(Hex Bolts) 六角螺丝(栓)141 Hex Head Machine Bolts 六角机械螺丝142 Hex Lag Bolts 六角木牙螺丝143 Square Head Bolts 四角螺丝144 Carriage Bolts 马车各式螺丝类产品自动包装Automatic Packaging For All Kinds Of Packaging 自动包装机Automatic Packing Machine 螺丝制造搓牙机械Automatic Thread Rolling Machine 螺丝割尾加工机械Automatic Thread Slotting Machine 螺丝制造成型机械Automatic Trimming Machine 拉钉打头机Blind Rivet Heading Machine 螺丝、螺帽成型机Bolt Formers,Nuts Formers,Headers 螺丝、螺帽热处理Bolt Nut And Screws Heat Treatment 螺丝、螺帽热处理炉Bolt Nut And Screws Heat Treatment Furnaces 球状化电器炖炉Carburizing Furnace Vacuum And Bell Type Furnace 超防锈复合瓷膜Ceramic Coating 连续式光辉渗碳淬火炉Continuous Bright Carburizing Quenching Furnace 连续式光辉调质淬火炉Continuous Bright Hardening Quenching Furnace 中、高热镀锌光辉连续炉Continuous Bright Heat Treat Furnace 连续式光辉热处理炉Continuous Type Bright Heat Treatment Furnace 螺丝割尾及特殊割遘加工Machine Screw Shank Slotting 螺丝钻孔加工Screw Shank Drilling 鸡眼上下模Eyelets Dies 一般线材、盘元、退火炉General Wire,Wire Rod,Annealing Furnace 倒立式滑落型伸线机Handstand Type Wire Drawing Machine 十字冲模Header Punches In Various Drives 成型冲模Header Punches In Various Drives 螺丝打头机Heading Machine 螺丝制造高速搓牙机械High Speed Automatic Thread Rolling Machine 高中低周波感应加热炉High,Medium,Low Frequency Induction Heater 空心打头机Hollow Heading Machine 热浸镀锌螺丝、螺帽Hot Dip Galvanizing Bolts And Nuts 机械镀锌Mechanical Galvanized 迷你成型机Mini-Formers 成品自动收线机Non-Stop Coiler 精抽自动收线机Non-Stop Coiler(Skinpass) 螺帽模Nut Forming Dies 螺帽成型模Nuts Formers 特殊零件成型机Parts Forming Maching 冲模Punch Dies 冲子Punch Pins 罗拉成型机Rollers Formers 机(踏)车用螺丝成型机Screw For Motorcycle Or Bicycle Heading Machine 止付螺丝成型机Set Screws Formers 套高成型机Sockets Formers 一般线材、盘元、螺丝合金炖炉Spheroidizing Bright Annealing Furnace 球状化热处理炉Spheroidizing Heat Treatment Furnace 攻牙机Tapping Machine 螺丝攻、车刀、模具Taps Dies And Tools 搓牙机铁屑分离装置Thread Chip Separator 滚牙轮Thread Rolling Dies 牙板Thread Rolling Dies Plates 精密油压滚牙机Hydraulic Thread Rolling Machines 模具Tools 六角整头模Trimming Dies Hexagan 碳化钨模具Tungsten Carbide Die 镀钛处理(Tin)专业加工服务Tin Hard Coating For Cutting Tools And Punch By Pvd 电镀化学原料Various Electroplating Chemicals 环规校正Calibration For Ring Gage 环规、牙规、三线规校正Calibration For Ring Gage, Athread Gage, 3 Wire Gage 螺丝、螺帽品检量测仪器Fasteners Inspection And Measurement Instruments 螺丝、螺帽成型攻牙专用油Forming And Tapping Oils For Bolts And Nuts Formers 螺丝、螺帽五金等检验Insptection Services For Fasteners And Hardware 德国schatz扭力机代理Representative Of Schatz Torque Machin Iso 品质保证系统Iso Quality Assurance System 生产管理系统Production Control System 物料管理系统Material Control System 齿轮Gears 不锈钢牙条棒Stainless Steel Hread Rod 马达轴承轴心组件Bearing Shaft(Motor) 轴承轴心Bearing Shaft 开口铆钉Blind Rivets 长形拉帽Blind Rivet Nuts 拉帽Blind Nuts 拉钉Blind Rivets 实心梢Clevis Pins And Straight Pins 弹片Clips 卷钉Coil Nails 冷锻零件Cold Forming Part 开口销Cotter Pins E型环E-Rings 膨胀螺栓Expansion Anchor Bolts 鸡眼钉Eyelets Rivets R型销Snap Pins 闸、锁Latches And Keeper Assembleds 其它特殊铆钉Other Specil Rivets 销Pins 格式管夹、管束Pipe Hanger 铆钉Rivets 螺旋锔及螺旋圈Screw Hook And Screw Rings 中空钉Semi-Tubular Rivet 开叉钉Split Drive Anchors 弹簧华司Spring Washers 弹簧蝴蝶夹Spring Wings 不锈钢华司Stainlesssteel Washers 钢铁钉Steel And Iron Nails 搓牙铁钉Thread Nails 钛合金铆钉Titaium Alloy Rivets 管形铆钉Tubular Rivets 华司Washers 真空热处理Vacuum Heat Treatment 螺丝、螺帽、五金、Diy扣件Fasteners 合金钢工具Alloy Steel Tools 螺栓模Bolt Heading Dies 手动拉钉钳Hand Riveter 船舶链Anchor Chain 脚踏车链锁Bicycle Chain Locks 螺丝起子Bit 罗拉Chain Roller 特殊铆合扣件Collars(A Blindfastener For Huck Intl) 装饰链Decorative Chains 自攻螺纹衬套Ensat Threaded Inserts 六角扳手Hexagon Keys 超音螺纹压入式螺纹自动锁扣Threaded Inserts For Plastic Injection Mouldeings 汽车特殊杆接件Special Auto-Mobile Fastener As Your Needs 螺纹护套Recoil Inserts 链条用滚子Roller For Roller Chain 金属板镶嵌组件及自动夹扣组件Sheet Metal Fasteners 工具套筒组件Socket Wrench Sets 不锈钢链Stainless Steel Chains 轭子T-Yoke 轮胎链Tire Chains 狗链Dog Chains 喇叭头轭铁U-Yoke,T-Yoke For Speaker 不锈钢输送带轮用轨道Stainless Wheel's Rack For Transporter 工业用链Industrial Steel Link Chains 拖链安全链Tow Chains And Safety Chains 机车离合器零件Manufacture Of Motorcycle's Cvt Parts 牙条棒Thread Rod紧固件专用词中英文对照螺丝(screw)英文英文简写中文示意图头部形状(Head style)Pan Head Pan HD 盘头Flat Head Flat HD 平头或countersunk Head CS HD 沉头Round Head RD HD 圆头Oval Head OL HD 半沉头Pan washer Head Pan wash HD 垫圈盘头Socket Hd Skt HD 六角圆柱头Hexagon cap Head Hex Cap HD 外六角头Square shouder Head SQ SDR HD 方肩头Cheese Head Ches HD 圆锥头Wing Head Wing HD 带翼头穴型状(Driver style)Philips cross recessed Phil 十字Pozidriv cross recessed Pozi 米字Torx Torx内梅花6-lobular 6-lobuSocket Skt 内六角Slot Slt 一字槽表面处理(coating) Znic blue ZB 兰锌Zinc black ZBK 黑锌Zinc yellow(Zinc oliver) ZY (ZO) 黄锌Zinc white ZW 白锌Silver Plating Sil Plat 镀银Nickel Plating Nic Plat 镀镍Dacromet Dacr 达克罗Heat dip zinc HDZinc 热浸锌1 screw scr螺丝2 nut nut螺母3 washer wash垫圈4 head hd 头5 thread thre螺纹6 coating coat 镀层7 rivet riv 铆钉8 standoff stdoff 内外六角钉9 driver driv 穴10 hexagon hexa 六角11 tooth tooth 齿12 lock lck 锁13 spring spr 弹簧14 wave wave 波浪型15 pitch pitch 牙距16 partial thread P T 半螺纹17 PT PT 一种螺纹形式18 Full Thread FT 全螺纹19 silver silv 银20 cone cone 锥形21 Eco-syn Eco 30度牙的一种螺纹22 Thread Forming TF 自攻螺纹23 Self Tapping self tapp 自切屑螺纹24 pin pin 销25 shaft Shaf 轴26 steel St 铁27 stainless steel SS 不锈钢28 Brass(Cu) Bras(Cu) 铜29 Aluminum AL 铝30 Rubber Rub 橡胶31 machine screw mech scr 机制螺丝32 SEM screw SEM Scr 组合螺丝33 Material material 材料34 Grade GD 等级35 Finish Finish 表面处理36 Point Point 点37 Clamp Clam 夹子38 internal Int 内39 external ext 外40 thickness / 厚度41 length / 长度42 hole / 孔43 Metric Metcric 公制44 DIN / 德标45 ANSI / 美标46 JIS / 日标47 ISO / 国际标准48 NFE / 法标49 GB / 国家标准50 Quality / 质量51 surface hardness 表面硬度52 product treatment 表面处理53 plating 电镀54 heat 热55 Screws And Shafts For Motorcycle Or Bicycle 机(踏)车用螺丝、轴心56 Screws And Shafts For Sewing Maching 针车用螺丝、轴心57 Socket Set Screws 止付螺丝58 Stainless Steel Coarse Thread Screws 不锈钢宽牙螺丝59 Stainless Steel High-Low Thread Screws 不锈钢高低牙螺丝60 Stainless Steel Machine Screws 不锈钢机械螺丝61 Stainless Steel Self Drilling Screws 不锈钢钻尾螺丝62 Stainless Steel Self Tapping Screws 不锈钢自攻螺丝63 Stainless Steel Thread Cutting Screws 不锈钢自削螺丝64 Stainless Steel Tri-Lobular Thread Screws 不锈钢三角牙螺丝65 Steel Ceiling Anchors 插片壁虎66 Drop in Anchors 内迫壁虎67 Steel Hit Anchors 碳钢锤钉壁虎68 Steel Hex Coupling Nuts 碳钢六角螺帽69 Wedge Anchors 强力车修壁虎70 Cut Anchors 外迫壁虎71 Chemical Anchors 化学壁虎72 Heavy Duty Expansion Anchors 不锈钢重载胀栓73 Tie Wire Anchors 鱼眼壁虎企眼长螺帽74 Hammer Drive Anchors 锌合金打入式壁虎75 Strut Nuts 弹簧螺帽76 Toggle Bolts (Spring Toggle & Gravity Toggle) 兰花夹系列77 Nylon Frame Anchors or Metalframe Anchors 门窗、地板专用壁虎78 Hollow Wall Anchors 石膏板中空壁虎79 Sleeve Anchors 套管式壁虎80 Nylon Frame Harmmer Fixing (Nylon Hammer Drive Anchors) 打入式壁虎鱼形尼龙壁虎81 Hit Anchors 强力式锤钉壁虎82 Bolt Anchors 电梯壁虎83 Heavy duty anchors 重载壁虎84 Loxin Masonry Anchors 两片夹85 Set Bolts 定位螺栓86 Short Strap Anchors 长型兰花夹87 Drop in Setting Tools 工具棒88 Elephant foot anchors 象脚壁虎89 Concrete Insert 水泥预埋件90 Drop in Anchor with Lip 翻边胀轴91 Legs Drywall Anchors 冲件92 Hex Cap Nuts 六角盖头螺帽93 Hex Serrated Nuts 六角锯齿螺帽94 Hex Flange Nuts 六角轮缘螺帽95 Hex Coupling Nuts(High Nuts) 高脚螺帽96 Round Nuts 圆螺帽97 Square Nuts 四角螺帽98 Pipe Nuts 管用螺帽99 Wheel Nuts 轮壳螺帽100 Wing Nuts 蝶型螺帽101 U Nuts U形螺帽102 T Nuts T形螺帽103 Eye Nuts 环首螺帽104 Kep Nuts 齿形螺帽105 Clinch Nuts 齿花螺帽106 Corten Steel Heavy Hex Nuts 耐候钢六角重型螺帽107 Weld Nuts 焊接螺帽108 Heigh Strength Nuts 高张力螺帽109 Structural Nuts 建业用螺帽110 Stainless Steel Nuts 不锈钢螺帽111 Brass Nuts 铜螺帽112 Aluminum Nuts 铝螺帽113 Alloy Steel Nuts 合金钢螺帽114 Heavy Duty Wheel Hub Nuts 重型车螺帽115 Acorn Cap Nuts 铁器焊接袋帽116 All-Metal Prevailing Torque Type Nuts 金属预置扭矩式螺帽117 Anchor Nuts 壁虎螺帽118 Big Size Nuts 大尺寸螺帽119 Closed End Acorn Nuts 铁盖袋帽120 Conical Washer Nuts 盘形华司螺帽121 Din 986 Domed Cap Nuts 铁盖+尼龙圈组合盖帽122 Flange Nylon Insert Lock Nuts 突缘尼龙盖帽123 Flat Waser Nuts 平面华司螺帽124 Hex Slotted Nut 六角割沟螺帽125 Self-Locking Nuts 自锁螺帽126 Sliding Nuts 制止螺帽127 Sln Self-Locking Nuts Sln-自动防松螺帽128 Special Nuts 其它特殊螺帽129 Spring Nuts 弹簧螺帽130 Stainless Steel Flange Nuts 不锈钢突缘螺帽131 Stainless Steel Flange Nylon Insert Lock Nuts 不锈钢六角轮缘尼龙螺帽132 Stainless Steel Heavy Hex Nuts 不锈钢六角重型螺帽133 Stainless Steel Hex Nuts 不锈钢六角螺帽134 Stainless Steel Nylon Insert Lock Nuts 不锈钢尼龙嵌入螺帽135 Hex Nuts 普通六角螺帽136 Heavy Hex Nuts 六角重型螺帽137 Hex Jam Nuts 薄型螺帽138 Nylon Insert Lock Nuts 尼龙嵌入防松螺帽139 Hex Machine Screw Nut 机械螺丝用六角螺帽140 Hex Head Cap Screws(Hex Bolts) 六角螺丝(栓)141 Hex Head Machine Bolts 六角机械螺丝142 Hex Lag Bolts 六角木牙螺丝143 Square Head Bolts 四角螺丝144 Carriage Bolts 马车螺丝145 Eye Bolts 环首螺丝146 Hex Socket Cap Screws 内六角孔螺丝147 Set Screws 固定螺丝148 Stud Bolts 螺椿栓149 Screw Studs 螺旋椿150 Wheel Bolts 轮壳螺栓151 Wing Screws 翼形螺丝152 Self Tapping Screws 自攻螺丝153 Thread Cutting Screws 自削螺丝154 Self Drilling Screws 钻尾螺丝155 Drive Screws 旋入螺丝156 Machine Screws 机械螺丝157 Wood Screws 木螺丝158 Furniture Screws 家具螺丝159 Chipboard Screws 塑板螺丝160 Drywall Screws 墙用螺丝161 Foundation Bolts 基础螺栓162 U Bolts U型螺栓163 Hook Bolts 勾头螺栓164 Toggle Bolts 套挂螺丝165 Flange Bolts 突缘螺丝166 Track Bolts 轨道螺栓(鱼尾螺丝)167 Corten Steel Heavy Hex Bolts 耐候钢螺丝168 T.C.Bolts 扭矩控制螺栓169 High Strength Bolts 高张力螺栓170 Welding Studs 剪力钉(焊接螺丝)171 Screws And Washers Assembled(Sems) 螺丝附华司组合172 Big Size Bolts 大尺寸螺栓173 Stainless Steel Sheet Metal Screws 不锈钢小螺丝174 Stainless Steel Bolts 不锈钢大螺丝175 Brass Screws 铜螺丝176 Aluminum Screws 铝螺丝177 Alloy Steel Screws 合金钢螺丝178 Electronic Screws 电子螺丝179 Micro Screws 微小精密螺丝180 Plastic Screws 塑料螺丝181 Particle Board Screws 复合材料用螺丝182 Titanium Alloy Bolts 钛合金螺丝183 Ti,Zr,Mo,Nb Pare Metal Bolts Parts 钛、锆、钼、铌等螺丝、零件、材料184 Thumb Screws 拇指螺丝185 Double End Screws Hanger Bolt 双头牙螺丝186 Automotive Fasteners 车辆(汽车)螺丝、螺帽187 Aerospace Fasteners 航天用螺丝188 Source Control Bolts 飞机特殊扣件189 Blind Bolts 拉栓190 Panel Fasteners 面板螺丝191 Elevator Bolts 电梯螺丝192 Square Set Screws 四角头固定螺丝193 T Head Bolts T头螺丝194 Step Bolts 大头马车螺丝195 One Way Lag Screws 单向螺丝196 Hose Clamp Screws 管夹螺丝197 Stainless Steel Hex Socket Cap Screws 不锈钢固定螺丝198 Stainless Steel Hex Socket Cap Screws 不锈钢内六角螺丝199 Hinge Screws 铰链螺丝200 Container Screws 货柜螺丝201 Bi-Metal Self Drilling Screws 复合材料钻尾螺丝202 Trilobular Thread Screws 三角牙螺丝203 High Low Screws 高低牙螺丝204 Particle Board Screws 夹板用螺丝205 Toilet Closet Bolts 马桶螺丝206 Special Longer Screws 特长螺丝207 Building Fasteners 建业螺丝208 Stainless Steel Hex Socket Cap Screws 不锈钢六角螺丝209 Special Screws Or Bolts 其它特殊螺丝210 Special Stainless Steel Screws 不锈钢特殊螺丝211 Collated Screws 链带螺丝212 Coarse Thread Screws 宽牙螺丝（粗牙螺丝）213 Concrete Screws 水泥螺丝214 Construction Bolts 板模螺丝215 Die Cast Wing Screws; Zinc Alloy 锌蝶螺丝216 Heavy Duty Wheel Hub Bolts 重型车螺丝217 Hex Socket Set Screws 内六角固定螺丝218 Particle Board Screws 复合材料用螺丝（夹板用）219 Plow Bolts 犁壁螺丝220 Stainless Steel Wood Screws 不锈钢木螺丝221 Toggle Bolts 套挂螺栓及螺丝222 Titanium Alloy Expansion Bolts 钛合金膨胀螺丝223 Hex Cap Nuts 六角盖头螺帽224 Hex Serrated Nuts 六角锯齿螺帽225 Hex Flange Nuts 六角轮缘螺帽226 Hex Coupling Nuts(High Nuts) 高脚螺帽227 Round Nuts 圆螺帽228 Square Nuts 四角螺帽229 Pipe Nuts 管用螺帽230 Wheel Nuts 轮壳螺帽231 Wing Nuts 蝶型螺帽232 U Nuts U形螺帽233 T Nuts T形螺帽234 Eye Nuts 环首螺帽235 Kep Nuts 齿形螺帽236 Clinch Nuts 齿花螺帽237 Corten Steel Heavy Hex Nuts 耐候钢六角重型螺帽238 Weld Nuts 焊接螺帽239 Heigh Strength Nuts 高张力螺帽240 Structural Nuts 建业用螺帽241 Stainless Steel Nuts 不锈钢螺帽242 Brass Nuts 铜螺帽243 Aluminum Nuts 铝螺帽244 Alloy Steel Nuts 合金钢螺帽245 Heavy Duty Wheel Hub Nuts 重型车螺帽246 Acorn Cap Nuts 铁器焊接袋帽247 All-Metal Prevailing Torque Type Nuts 金属预置扭矩式螺帽248 Anchor Nuts 壁虎螺帽249 Big Size Nuts 大尺寸螺帽250 Closed End Acorn Nuts 铁盖袋帽251 Conical Washer Nuts 盘形华司螺帽252 Din 986 Domed Cap Nuts 铁盖+尼龙圈组合盖帽253 Flange Nylon Insert Lock Nuts 突缘尼龙盖帽254 Flat Waser Nuts 平面华司螺帽255 Hex Slotted Nut 六角割沟螺帽256 Self-Locking Nuts 自锁螺帽257 Sliding Nuts 制止螺帽258 Sln Self-Locking Nuts Sln-自动防松螺帽259 Special Nuts 其它特殊螺帽260 Spring Nuts 弹簧螺帽261 Stainless Steel Flange Nuts 不锈钢突缘螺帽262 Stainless Steel Flange Nylon Insert Lock Nuts 不锈钢六角轮缘尼龙螺帽263 Stainless Steel Heavy Hex Nuts 不锈钢六角重型螺帽264 Stainless Steel Hex Nuts 不锈钢六角螺帽265 Stainless Steel Nylon Insert Lock Nuts 不锈钢尼龙嵌入螺帽266 Zinc Die Casting Nuts 锌压属螺帽267 Hex Nuts 普通六角螺帽268 Heavy Hex Nuts 六角重型螺帽269 Nylon Insert Lock Nuts 尼龙嵌入防松螺帽270 Hex Jam Nuts 薄型螺帽271 Hex Machine Screw Nut 机械螺丝用六角螺帽272 Alloy Steel Wire Rod 合金钢线材盘元273 Annealing Wire And Rod 球状化线材274 Black Wire 黑铁丝275 Brass Wire And Rod 黄铜棒线276 Bright Steel Bar(Hex/Round/Square) 磨光棒钢277 Copper Alloy Wire 铜合金线278 E.D.M Cutting Wire 线切割线279 Free Cutting Steel Wire Rod 快削钢线材盘元280 Iron Or Steel Wire 线材281 Iron Or Steel Wire Rod 线材盘元282 Nickel Silver Wire 洋白铜线283 Phosphate Bronze Wire 磷青铜线284 Stainless Steel Bar(Round/Hex/Square) 不锈钢条棒285 Stainless Steel Cold Heading Wire 不锈钢冷锻线材286 Stainless Steel Draw Wire 不锈钢线(抽线后)287 Stainless Steel Wire 不锈钢线材288 Stainless Steel Wire And Rod 不锈钢线材及盘元289 Steel Bar(Hex/Round/Square) 棒钢290 evolving Wire Twisting Machine 转回90度碾线头机 90讧291 Air Riveter 气动拉钉机。

Standard 标准American system (ANSI ）Japan system （JIS ）German system （DIN )Material 材质Aluminium 铝aluminum alloy 铝合金steel 钢stainless steel不锈钢Copper纯铜brass 黄铜metal 金属wood 木Red copper 紫铜、赤铜Type 类型（Style 风格）Drive Rivet --—-——--—--——-————击芯铆钉Plastic Rivets ———-—-———-——————塑料铆钉Riveting Tool Rivets ---———-—铆接工具Structure ［strʌktʃə] Rivet 结构型铆钉Ordinary ［ɔ：dinəri］Rivet 普通型铆钉Open End Blind Rivet --—————开口型抽芯铆钉Open Type Blind RivetsClosed End Blind Rivet --—-—封闭型抽芯铆钉Sealed Type Blind Rivets Multi—grip Rivet -—————--———-- 双鼓型抽芯铆钉Multigrip Type Blind RivetsSingle-grip Rivet —--—-———————单鼓型抽芯铆钉Peel Type Blind Rivet -———-—拉花型抽芯铆钉Grooved Type Blind Rivet 沟槽型抽芯铆钉Fold Type Blind Rivets —--——抽折式抽芯铆钉Ring-Grooved Lockbolt ———-- 环槽铆钉Maolock -———-———-—————-—-—————拉丝铆钉（Interlock 内锁拉丝；Monobolt外锁拉丝)Hemlock ————--———------———---—- 海马钉Rivkle ——-——-————-—————————————铆螺母（Insert Nut ）Bulbex -——--—--————--—-—-——————灯笼铆钉(Lantern Rivet）Speed Fasteners —--——---—————快速铆钉Briv -—-—————-——-—-————————-——-—迫扣式（pockz）Chobert —--—---——-————————-————苏拔式（suborz）Grovit -———-———————-—————---—--—高域型（goniz)Rivscrew ————-——————--———-————螺纹式（Hexagon screw) Avtronic ---——-————-———————————连接器式(connector）Avsert —-—-—————-—--—-———--—————插柱式（knobbed cylinder) Avlug ----————-—-—————--———--—-—端子式（terminal）Head and Body 头部和身体Large Head 大帽Flat Head （pan）平头Countersunk Head 沉头Extra—small Countersunk Head 小沉头Dome Head 圆头Hexagonal body 六角形Round body 圆身Part Hexagonal body 半六角Knurled 滚花Plain 平滑型Bulbed 球状Tail 尾部Specialized Content Vocabulary 专业术语(professional language）Clamp thickness 夹持母材厚度Grip range 铆接范围Hole dimensions 安装孔径Mandrel ［mændril 芯轴Nosepiece ［nəuzpi：s］旋座Diameter 直径Part Number 编号Key Features 重要特征Clamp 夹紧Removable 可移动折曲式Shear 抗剪Torsion resistance 抗扭Tension 抗拉Tensile strength 抗拉强Stoving varnish 烤漆Water proof 防水Excuse me for interrupting you.请原谅我打扰你.I’m sorry to disturb you。

Description in Chinese 英文品名Desciption in English圆锥销Taper pins圆柱销Parallel pins开槽圆柱头螺钉Slotted cheese head screws开槽盘头螺钉Slotted pan head screws单耳止动垫圈Tab washers开口销Split cooter pins开槽半沉头木螺钉Slotted raised csk head wood screws 开槽半圆头木螺钉Slotted round head wood screws开槽沉头木螺钉Slotted countersunk head wood screws 平垫Plain washers平垫（带倒角）Mediun washers平垫Plain washers重型弹垫Spring lock washers,tang ends标准弹垫Spring lock washers,square ends鞍形弹垫Single coil spring lock washers弹簧止动垫圈Curved spring washers波形弹垫Wave spring washersT型方颈螺栓T-head blots with square neckT型双接头螺栓T-head bolts with double nip螺纹圆锥销Taper pins with threaded endT型头螺栓T-head bolts蝶型螺母（美制）Wing nuts America form蝶型螺母（德制）Wing nuts germany form蝶型螺母（美制）Wing screws America form蝶型螺母（德制）Wing screws germany form圆球型盖型螺母Ball knobs开槽带孔球面圆柱头蚴钉Slotted capstan screws开槽长圆柱端紧定螺钉Slotted set srews with full dog point开槽平端紧定螺钉（半牙）Slotted set srews with chamfered end 小六角特薄细牙螺母Pip nuts with thread外舌止动垫圈External tap小垫圈(用于圆柱头螺钉) Washers for cheese head screws方斜垫圈（U型）Square taper washers forU-section方斜垫圈（I型）Square taper washers forI-sections方垫圈Square washers开槽凹端紧定螺钉Slotted set with cup point六角薄螺母Hexagon thin nuts细牙六角薄螺母Hexagon thin nuts木螺钉专用垫圈Rounds washers for wood constructions密封帽Sealing caps,push-in type活节螺栓B型Eye bolts form B内舌止动垫圈Internal tab washers双耳止动垫圈Washers with two taps滚花高头螺钉Knurled thumb screws with collar开槽滚花高头螺钉Slotted knurled thumb screws with collar 滚花高螺母Knurled thumb nuts with collar滚花薄螺母Knurled thumb thin nuts锁紧垫圈Sealing washers轴用弹性垫圈Retaining rings for shafts(external),circlips孔用弹性垫圈Retaining rings for bores(internal),circlips方头带垫螺栓Square head bolts with collar方头圆柱底端螺栓Square head bolts with half dog point方头带垫关圆底端螺栓Square head bolts with collar,half dog pointT型槽螺母T-slot nuts单头螺柱Single end studs地脚螺栓Masonry bolts带槽圆螺母Slotted round nuts端面带孔圆螺母Round nuts with drilled holes in one face 开槽平端紧定螺钉Slotted set screws with flat point开槽锥端紧定螺钉Slotted set screws with cone point六角螺母Hexagon nuts方螺母-C Square nuts六角头螺钉Hexagon screws六角头圆柱端紧定螺钉Hexagon set screws with full dog point薄型方螺母-B Square nuts without bevel(pressed nuts)六角头木螺钉Hexgon head wood screw(coach screws)吊环螺钉Lifting eye bolts吊环螺母Lifting eye nuts圆锥型槽销Grooved pins,taper grooved圆锥型槽销（半槽）Grooved pins,taper grooved half length平行槽销（带倒角）Grooved pins,parallel grooved full length前端凹槽槽销Grooved pins,reverve grooved half length中部凹槽槽销Grooved pins,center grooved圆头槽销Grooved pins with round head沉头槽销Grooved pins with countersunk head六角螺母棒Turnuckles(center parts),made out of hexagon bar花蓝螺栓Turnuckles with eye bolt and hook bolt弹性圆柱销Spring pins,heavy type组合式盖型螺母Hexagon domed cap nuts开槽圆螺母(配合沟头扳手) Slotted round nuts for hook spammer圆螺母（带插销孔）Round nuts with set holes盘型弹簧垫圈Disc springs喉箍Hose clamps润滑油嘴（旋扭头）Lubricating nipples,button head管夹Shackles for conduiltsU型螺栓Stirrup bolts(U-bolts)球面垫圈Spherical washers,conical seats圆柱销Parallel pins厚六角螺母Hexagon nuts,1.5d厚六角法兰面螺母Hexagon nuts,1.5d with collar长六角螺母Hexagon nuts,3d外齿锁紧垫圈External teeth lock washers内齿锁紧垫圈Internal teeth lock washers外锯齿锁紧垫圈External teeth serrated lock washers内锯齿锁紧垫圈Internal teeth serrated lock washers开口挡圈Retaining rings for shafts(E-rings),circlips平键（A型）Parallel keys(form A)半圆键Woodruff keys嵌环（支撑环）Thimbles机器螺钉和垫圈组合件Screws and washers assemblies自攻螺钉和垫圈组合件Tapping screws and washer assemblies薄型带孔内六角圆柱螺钉Hexagon cocket head cap screws with hole,low head大六角头螺栓Hexagon head bolts with large head(friction grip nolts)大六角螺母Hexagon nuts with large wideth across flat(friction grip nuts)大垫圈Round washers for friction grip bolts楔型方垫圈Spuare taper washers for friction grip bolts on T-六角法兰面螺母Hexagon flange nuts全金属六角锁紧螺母（2型）Prevailing torque type hexagon nuts,all metallic nuts 轻型弹性圆柱销Spring pins,light type重型弹性圆柱销用垫圈Washers for bolts with heavy type spring pinssISO公制螺纹螺钉（多种头型）Thread forming screws for ISO-metric thread 自攻自钻螺钉（多种头型）Self-drilling tapping screws开槽切削螺纹螺钉（多种头型）Thread cutting screws十字槽切削螺纹螺钉（多种头型）Thread cutting screws cross recessT型四爪螺母Tee nuts with pronge钢结构用六角头螺栓连接副Hexagon head fitted bolts for steel structures开槽盘头自攻螺钉Pan head tapping screws with slot开槽沉头自攻螺钉countersunk flat head tapping screws with slot开槽半沉头自攻螺钉Raised sountersunk oval head tapping screws with slot六角头自攻螺钉Hexagon tapping screws圆柱头螺钉用弹簧垫圈Spring lock washers for screws with cylindrical heads十字槽盘头自攻螺攻Pan head tapping screws with cross recessed十字槽沉头自攻螺攻Countersunk flat head tapping screws with cross recessed十字槽半沉头自攻螺攻Raised countersunk oval head tapping screws with cross薄型内六角圆柱头螺钉Hexagon socket head cap screws with,reduced head十字槽盘头螺钉Pan head screws with cross recessed钢结构用垫圈Washers for steel structures钢结构用六角头螺栓Hexagon head bolts for steel structures内六角沉头螺钉Hexagon socket coutersunk head screws轴用钢丝挡圈Roundwire snap rings for shafts十字槽半沉头木螺钉Cross recessed raised countersunk head wood screws十字槽圆头木螺钉Cross recessed round head wood screws十字槽沉头木螺钉Cross recessed countersunk head wood screws螺纹护套(普通、自锁等) Ciol inserts,coarse,fine thread,silf locking大外径垫圈Washers,outside diameter appro.3d弹簧卡子sping cotter for a bolt平板螺栓Belting bolts(elevator bolts)干壁钉（墙板钉）Dry wall screws环型螺母Lifting nuts(eye nuts)圆螺母用止退垫圈Tab washer for slotted round nuts。

常用紧固件英语六角螺丝(栓) HEX HEAD CAP SCREWS(HEX BOLTS) 六角机械螺丝 HEX HEAD MACHINE BOLTS六角木牙螺丝 HEX LAG BOLTS四角螺丝 SQUARE HEAD BOLTST头螺丝 T HEAD BOLTS马车螺丝 CARRIAGE BOLTS环首螺丝 EYE BOLTS内六角孔螺丝 HEX SOCKET CAP SCREWS固定螺丝 SET SCREWS螺椿栓 STUD BOLTS螺旋椿 SCREW STUDS轮壳螺栓 WHEEL BOLTS翼形螺丝 WING SCREWS自攻螺丝 SELF TAPPING SCREWS自削螺丝 THREAD CUTTING SCREWS钻尾螺丝 SELF DRILLING SCREWS旋入螺丝 DRIVE SCREWS机械螺丝 MACHINE SCREWS木螺丝 WOOD SCREWS家具螺丝 FURNITURE SCREWS塑板螺丝 CHIPBOARD SCREWS墙用螺丝 DRYWALL SCREWS基础螺栓 FOUNDATION BOLTSU型螺栓 U BOLTS勾头螺栓 HOOK BOLTS套挂螺丝 TOGGLE BOLTS突缘螺丝 FLANGE BOLTS轨道螺栓(鱼尾螺丝) TRACK BOLTS耐候钢螺丝 CORTEN STEEL HEAVY HEX BOLTS扭矩控制螺栓高张力螺栓 HIGH STRENGTH BOLTS剪力钉(焊接螺丝) WELDING STUDS螺丝附华司组合 SCREWS AND WASHERS ASSEMBLED(SEMS) 大尺寸螺栓 BIG SIZE BOLTS不锈钢小螺丝 STAINLESS STEEL SHEET METAL SCREWS 不锈钢大螺丝 STAINLESS STEEL BOLTS铜螺丝 BRASS SCREWS铝螺丝 ALUMINUM SCREWS合金钢螺丝 ALLOY STEEL SCREWS电子螺丝 ELECTRONIC SCREWS微小精密螺丝 MICRO SCREWS塑料螺丝 PLASTIC SCREWS复合材料用螺丝 PARTICLE BOARD SCREWS钛合金螺丝 TITANIUM ALLOY BOLTS钛、锆、钼、铌等螺丝、零件、材料 TI,ZR,MO,NB PARE METAL BOLTS PARTS拇指螺丝 THUMB SCREWS双头牙螺丝 DOUBLE END SCREWS HANGER BOLT车辆(汽车)螺丝、螺帽 AUTOMOTIVE FASTENERS航天用螺丝 AEROSPACE FASTENERS飞机特殊扣件 SOURCE CONTROL BOLTS拉栓 BLIND BOLTS面板螺丝 PANEL FASTENERS电梯螺丝 ELEVATOR BOLTS四角头固定螺丝 SQUARE SET SCREWS大头马车螺丝 STEP BOLTS单向螺丝 ONE WAY LAG SCREWS管夹螺丝 HOSE CLAMP SCREWS不锈钢固定螺丝 STAINLESS STEEL HEX SOCKET CAP SCREWS不锈钢内六角螺丝 STAINLESS STEEL HEX SOCKET CAP SCREWS铰链螺丝 HINGE SCREWS货柜螺丝 CONTAINER SCREWS复合材料钻尾螺丝 BI-METAL SELF DRILLING SCREWS三角牙螺丝 TRILOBULAR THREAD SCREWS高低牙螺丝 HIGH LOW SCREWS夹板用螺丝 PARTICLE BOARD SCREWS马桶螺丝 TOILET CLOSET BOLTS特长螺丝 SPECIAL LONGER SCREWS建业螺丝 BUILDING FASTENERS不锈钢六角螺丝 STAINLESS STEEL HEX SOCKET CAP SCREWS其它特殊螺丝 SPECIAL SCREWS OR BOLTS不锈钢特殊螺丝 SPECIAL STAINLESS STEEL SCREWS宽牙螺丝（粗牙螺丝） COARSE THREAD SCREWS链带螺丝 COLLATED SCREWS水泥螺丝 CONCRETE SCREWS板模螺丝 CONSTRUCTION BOLTS锌蝶螺丝 DIE CAST WING SCREWS; ZINC ALLOY重型车螺丝 HEAVY DUTY WHEEL HUB BOLTS内六角固定螺丝 HEX SOCKET SET SCREWS复合材料用螺丝（夹板用） PARTICLE BOARD SCREWS犁壁螺丝 PLOW BOLTS机(踏)车用螺丝、轴心 SCREWS AND SHAFTS FOR MOTORCYCLE OR BICYCLE针车用螺丝、轴心 SCREWS AND SHAFTS FOR SEWING MACHING止付螺丝 SOCKET SET SCREWS不锈钢宽牙螺丝 STAINLESS STEEL COARSE THREAD SCREWS不锈钢高低牙螺丝 STAINLESS STEEL HIGH-LOW THREAD SCREWS不锈钢机械螺丝 STAINLESS STEEL MACHINE SCREWS不锈钢钻尾螺丝 STAINLESS STEEL SELF DRILLING SCREWS不锈钢自攻螺丝 STAINLESS STEEL SELF TAPPING SCREWS不锈钢自削螺丝 STAINLESS STEEL THREAD CUTTING SCREWS不锈钢三角牙螺丝 STAINLESS STEEL TRI-LOBULAR THREAD SCREWS 不锈钢木螺丝 STAINLESS STEEL WOOD SCREWS套挂螺栓及螺丝 TOGGLE BOLTS钛合金膨胀螺丝 TITANIUM ALLOY EXPANSION BOLTS中文名称英文名称六角盖头螺帽 HEX CAP NUTS六角锯齿螺帽 HEX SERRATED NUTS六角轮缘螺帽 HEX FLANGE NUTS高脚螺帽 HEX COUPLING NUTS(HIGH NUTS)圆螺帽 ROUND NUTS四角螺帽 SQUARE NUTS管用螺帽 PIPE NUTS轮壳螺帽 WHEEL NUTS蝶型螺帽 WING NUTSU形螺帽 U NUTST形螺帽 T NUTS环首螺帽 EYE NUTS齿形螺帽 KEP NUTS齿花螺帽 CLINCH NUTS耐候钢六角重型螺帽 CORTEN STEEL HEAVY HEX NUTS焊接螺帽 WELD NUTS高张力螺帽 HEIGH STRENGTH NUTS建业用螺帽 STRUCTURAL NUTS不锈钢螺帽 STAINLESS STEEL NUTS铜螺帽 BRASS NUTS铝螺帽 ALUMINUM NUTS合金钢螺帽 ALLOY STEEL NUTS重型车螺帽 HEAVY DUTY WHEEL HUB NUTS铁器焊接袋帽 ACORN CAP NUTS金属预置扭矩式螺帽 ALL-METAL PREVAILING TORQUE TYPE NUTS 壁虎螺帽 ANCHOR NUTS大尺寸螺帽 BIG SIZE NUTS铁盖袋帽 CLOSED END ACORN NUTS盘形华司螺帽 CONICAL WASHER NUTS铁盖+尼龙圈组合盖帽 DIN 986 DOMED CAP NUTS突缘尼龙盖帽 FLANGE NYLON INSERT LOCK NUTS平面华司螺帽 FLAT WASER NUTS六角割沟螺帽 HEX SLOTTED NUT自锁螺帽 SELF-LOCKING NUTS制止螺帽 SLIDING NUTSSLN-自动防松螺帽 SLN SELF-LOCKING NUTS其它特殊螺帽 SPECIAL NUTS弹簧螺帽 SPRING NUTS不锈钢突缘螺帽 STAINLESS STEEL FLANGE NUTS不锈钢六角轮缘尼龙螺帽 STAINLESS STEEL FLANGE NYLON INSERT LOCK NUTS不锈钢六角重型螺帽 STAINLESS STEEL HEAVY HEX NUTS不锈钢六角螺帽 STAINLESS STEEL HEX NUTS不锈钢尼龙嵌入螺帽 STAINLESS STEEL NYLON INSERT LOCK NUTS锌压属螺帽 ZINC DIE CASTING NUTS普通六角螺帽 HEX NUTS六角重型螺帽 HEAVY HEX NUTS薄型螺帽 HEX JAM NUTS尼龙嵌入防松螺帽 NYLON INSERT LOCK NUTS机械螺丝用六角螺帽 HEX MACHINE SCREW NUT中文名称英文名称合金钢线材盘元 ALLOY STEEL WIRE ROD球状化线材 ANNEALING WIRE AND ROD黑铁丝 BLACK WIRE黄铜棒线 BRASS WIRE AND ROD磨光棒钢 BRIGHT STEEL BAR(HEX/ROUND/SQUARE)铜合金线 COPPER ALLOY WIRE线切割线 CUTTING WIRE快削钢线材盘元 FREE CUTTING STEEL WIRE ROD线材 IRON OR STEEL WIRE线材盘元 IRON OR STEEL WIRE ROD洋白铜线 NICKEL SILVER WIRE磷青铜线 PHOSPHATE BRONZE WIRE不锈钢条棒 STAINLESS STEEL BAR(ROUND/HEX/SQUARE)不锈钢冷锻线材 STAINLESS STEEL COLD HEADING WIRE不锈钢线(抽线后) STAINLESS STEEL DRAW WIRE不锈钢线材 STAINLESS STEEL WIRE不锈钢线材及盘元 STAINLESS STEEL WIRE AND ROD棒钢 STEEL BAR(HEX/ROUND/SQUARE)转回90度碾线头机 90讧EVOLVING WIRE TWISTING MACHINE气动拉钉机 AIR RIVETER各式螺丝类产品自动包装 AUTOMATIC PACKAGING FOR ALL KINDS OF PACKAGING自动包装机 AUTOMATIC PACKING MACHINE螺丝制造搓牙机械 AUTOMATIC THREAD ROLLING MACHINE螺丝割尾加工机械 AUTOMATIC THREAD SLOTTING MACHINE螺丝制造成型机械 AUTOMATIC TRIMMING MACHINE拉钉打头机 BLIND RIVET HEADING MACHINE螺丝、螺帽成型机 BOLT FORMERS,NUTS FORMERS,HEADERS螺丝、螺帽热处理 BOLT NUT AND SCREWS HEAT TREATMENT螺丝、螺帽热处理炉 BOLT NUT AND SCREWS HEAT TREATMENT FURNACES 球状化电器炖炉CARBURIZING FURNACE VACUUM AND BELL TYPE FURNACE超防锈复合瓷膜 CERAMIC COATING连续式光辉渗碳淬火炉 CONTINUOUS BRIGHT CARBURIZING QUENCHING FURNACE连续式光辉调质淬火炉 CONTINUOUS BRIGHT HARDENING QUENCHING FURNACE中、高热镀锌光辉连续炉 CONTINUOUS BRIGHT HEAT TREAT FURNACE 连续式光辉热处理炉 CONTINUOUS TYPE BRIGHT HEAT TREATMENT FURNACE螺丝割尾及特殊割遘加工 MACHINE SCREW SHANK SLOTTING螺丝钻孔加工 SCREW SHANK DRILLING鸡眼上下模 EYELETS DIES一般线材、盘元、退火炉 GENERAL WIRE,WIRE ROD,ANNEALING FURNACE 倒立式滑落型伸线机 HANDSTAND TYPE WIRE DRAWING MACHINE十字冲模 HEADER PUNCHES IN VARIOUS DRIVES成型冲模 HEADER PUNCHES IN VARIOUS DRIVES螺丝打头机 HEADING MACHINE螺丝制造高速搓牙机械 HIGH SPEED AUTOMATIC THREAD ROLLING MACHINE高中低周波感应加热炉HIGH,MEDIUM,LOW FREQUENCY INDUCTION HEATER空心打头机 HOLLOW HEADING MACHINE热浸镀锌螺丝、螺帽 HOT DIP GALVANIZING BOLTS AND NUTS机械镀锌 MECHANICAL GALVANIZED迷你成型机 MINI-FORMERS成品自动收线机 NON-STOP COILER精抽自动收线机 NON-STOP COILER(SKINPASS)螺帽模 NUT FORMING DIES螺帽成型模 NUTS FORMERS特殊零件成型机 PARTS FORMING MACHING冲模 PUNCH DIES冲子 PUNCH PINS罗拉成型机 ROLLERS FORMERS机(踏)车用螺丝成型机 SCREW FOR MOTORCYCLE OR BICYCLE HEADING MACHINE止付螺丝成型机 SET SCREWS FORMERS套高成型机 SOCKETS FORMERS一般线材、盘元、螺丝合金炖炉 SPHEROIDIZING BRIGHT ANNEALING球状化热处理炉 SPHEROIDIZING HEAT TREATMENT FURNACE攻牙机 TAPPING MACHINE螺丝攻、车刀、模具 TAPS DIES AND TOOLS搓牙机铁屑分离装置 THREAD CHIP SEPARATOR滚牙轮 THREAD ROLLING DIES牙板 THREAD ROLLING DIES PLATES精密油压滚牙机 HYDRAULIC THREAD ROLLING MACHINES模具 TOOLS六角整头模 TRIMMING DIES HEXAGAN碳化钨模具 TUNGSTEN CARBIDE DIE镀钛处理(TiN)专业加工服务 TiN HARD COATING FOR CUTTING TOOLS AND PUNCH BY PVD电镀化学原料 VARIOUS ELECTROPLATING CHEMICALS环规校正 CALIBRATION FOR RING GAGE环规、牙规、三线规校正 CALIBRATION FOR RING GAGE, ATHREAD GAGE, 3 WIRE GAGE螺丝、螺帽品检量测仪器 FASTENERS INSPECTION AND MEASUREMENT INSTRUMENTS螺丝、螺帽成型攻牙专用油 FORMING AND TAPPING OILS FOR BOLTS AND NUTS FORMERS螺丝、螺帽五金等检验 INSPTECTION SERVICES FOR FASTENERS AND德国SCHATZ扭力机代理 REPRESENTATIVE OF SCHATZ TORQUE MACHIN ISO质量保证系统 ISO QUALITY ASSURANCE SYSTEM生产管理系统 PRODUCTION CONTROL SYSTEM物料管理系统 MATERIAL CONTROL SYSTEM中文名称英文名称齿轮 GEARS不锈钢牙条棒 STAINLESS STEEL HREAD ROD马达轴承轴心组件 BEARING SHAFT(MOTOR)轴承轴心 BEARING SHAFT开口铆钉 BLIND RIVETS长形拉帽 BLIND RIVET NUTS拉帽 BLIND NUTS拉钉 BLIND RIVETS实心梢 CLEVIS PINS AND STRAIGHT PINS弹片 CLIPS卷钉 COIL NAILS冷锻零件 COLD FORMING PART开口销 COTTER PINSE型环 E-RINGS膨胀螺栓 EXPANSION ANCHOR BOLTS鸡眼钉 EYELETS RIVETSR型销 SNAP PINS闸、锁 LATCHES AND KEEPER ASSEMBLEDS其它特殊铆钉 OTHER SPECIL RIVETS销 PINS格式管夹、管束 PIPE HANGER铆钉 RIVETS螺旋锔及螺旋圈 SCREW HOOK AND SCREW RINGS 中空钉 SEMI-TUBULAR RIVET开叉钉 SPLIT DRIVE ANCHORS弹簧华司 SPRING WASHERS弹簧蝴蝶夹 SPRING WINGS不锈钢华司 STAINLESSSTEEL WASHERS钢铁钉 STEEL AND IRON NAILS搓牙铁钉 THREAD NAILS钛合金铆钉 TITAIUM ALLOY RIVETS管形铆钉 TUBULAR RIVETS华司 WASHERS真空热处理 VACUUM HEAT TREATMENT螺丝、螺帽、五金、DIY扣件 FASTENERS合金钢工具 ALLOY STEEL TOOLS螺栓模 BOLT HEADING DIES手动拉钉钳 HAND RIVETER船舶链 ANCHOR CHAIN脚踏车链锁 BICYCLE CHAIN LOCKS螺丝起子 BIT罗拉 CHAIN ROLLER特殊铆合扣件 COLLARS(A BLINDFASTENER FOR HUCK INTL)装饰链 DECORATIVE CHAINS自攻螺纹衬套 ENSAT THREADED INSERTS六角扳手 HEXAGON KEYS超音螺纹压入式螺纹自动锁扣THREADED INSERTS FOR PLASTIC INJECTION MOULDEINGS汽车特殊杆接件 SPECIAL AUTO-MOBILE FASTENER AS YOUR NEEDS螺纹护套 RECOIL INSERTS链条用滚子 ROLLER FOR ROLLER CHAIN金属板镶嵌组件及自动夹扣组件 SHEET METAL FASTENERS工具套筒组件 SOCKET WRENCH SETS不锈钢链 STAINLESS STEEL CHAINS轭子 T-YOKE轮胎链 TIRE CHAINS狗链 DOG CHAINS喇叭头轭铁 U-YOKE,T-YOKE FOR SPEAKER不锈钢输送带轮用轨道 STAINLESS WHEEL'S RACK FOR TRANSPORTER工业用链 INDUSTRIAL STEEL LINK CHAINS拖链安全链 TOW CHAINS AND SAFETY CHAINS机车离合器零件 MANUFACTURE OF MOTORCYCLE'S CVT PARTS 牙条棒 THREAD ROD。

No. 英文单词简写中文1 screw scr 螺丝2 nut nut 螺母3 washer wash 垫圈4 head hd 头5 thread thre 螺纹6 coating coat 镀层7 rivet riv 铆钉8 standoff stdoff 内外六角钉9 driver driv 穴10 hexagon hexa 六角11 tooth tooth 齿12 lock lck 锁13 spring spr 弹簧14 wave wave 波浪型15 pitch pitch 牙距16 partial thread PT 半螺纹17 PT PT 一种螺纹形式18 Full Thread FT 全螺纹19 silver silv 银20 cone cone 锥形21 Eco-syn Eco 30度牙的一种螺纹22 Thread Forming TF 自攻螺纹23 Self Tapping self tapp 自切屑螺纹24 pin pin 销25 shaft Shaf 轴26 steel St 铁27 stainless steel SS 不锈钢28 Brass(Cu) Bras(Cu) 铜29 Aluminum AL 铝30 Rubber Rub 橡胶31 machine screw mech scr 机制螺丝32 SEM screw SEM Scr 组合螺丝33 Material material 材料34 Grade GD 等级35 Finish Finish 表面处理36 Point Point 点37 Clamp Clam 夹子38 internal Int 内39 external ext 外40 thickness / 厚度41 length / 长度42 hole / 孔43 Metric Metcric 公制44 DIN / 德标45 ANSI / 美标46 JIS / 日标螺丝相关参数英语对照A: Machine Screw: 机械螺丝B: Tapping Screw: 自攻螺丝(分使用于金属与使用于塑料二种) B-1: Sheet Metal Tapping Screw. (铁板牙自攻螺丝)B-2: Plastic Tapping Screw. ( 塑料用, 自攻螺丝)C: Wooden Screw : 木工螺丝D: Drywall Screw : 水泥墙螺丝常见螺丝材质:a.Low Carbon Steel :低碳钢b. SS-304 : Stainless Steel 304c. SS-302: Stainless Steel 302 :结构韧性较好d. Aluminum 5052 :铝合金5052d. Brass: 黄铜e. Bronze: 青铜f. UNS C11000 Copper: 锑铜Finish Code: 外观处理规格Head Code: 头部外型螺丝型号Drive Code: 头部剖沟,特征型号Length Code: 螺丝长度(mm)A-1: Thread Code: 螺丝型号A-2: Length Code: 螺丝长度:A-3: Drive Code/ 头部剖沟,特征.a. Slotted: 一字( Minus )b. Phillips: 十字( Plus )c. Phil-Slot: 一字/十字d. Hex Scoket: 内六角e. One Way: 单向(只可锁入,不可退出)A-4: Head Code/ 头部外型.a. Flat: 平头(锁入后,顶部与工作件齐平)b. Oval: 色拉头c. Round: 圆头d. Pan: 圆扁头e. Truss: 大圆扁头f. Hex : 六角头A-5: Finish Code/ 外观处理.a. Z: Zine-Plated: 镀锌b. Ni: Ni-Plated: 镀镍c. Tin-Plated: 镀锡d. Zine Plated / Green Iridite: 镀锌绿膜处理.e. Radiant Plated: 镀五彩f. Passivate: 抗氧化处理.g. Alodial Finish: 无外观处理螺纹大径：Major Diam螺纹中径：Pitch diam螺纹底径：Minor diam通止规：Go/No go gage机械性能：mechanical and physical propertiesunified thread 统一英制螺纹Lustrate hydrogen after galvanizing to avoid hydrogen embrittlement 镀后去氢，防止氢脆Case carburization 表面渗碳With across flats 对边With across corners 对角Radius of fillet:头下圆角Transition thread length 过度螺纹Wrenching height 扳拧高度Rockwell 铬氏硬度Vickers 维氏硬度Brinell 布氏硬度Metallography microscope 金相显微镜Salt spray device 盐雾试验箱Tensile testing machine 拉力试验机Cold forming 冷打Hot forging 红镦P C 8 = property class 8 机械性能8级原材料：Raw material球化退火：Annealing冷拔：Drawing冷镦：Forming机加工：Machining螺纹成型：Roll Threading热处理：heat-treatment表面处理：finish去氢：Lustrating hydrogen检验：Inspection包装：Packing入库：Stocking车床：lathe磨制：grinding红打：hot forging冲压：punchingDiameter 直径Length 长度各类紧固件标准件产品英语翻译对照插片壁虎Steel Ceiling Anchors内迫壁虎Drop in Anchors碳钢锤钉壁虎Steel Hit Anchors碳钢六角螺帽Steel Hex Coupling Nuts强力车修壁虎Wedge Anchors外迫壁虎Cut Anchors化学壁虎Chemical Anchors不锈钢重载胀栓Heavy Duty Expansion Anchors鱼眼壁虎企眼长螺帽Tie Wire Anchors锌合金打入式壁虎Hammer Drive Anchors弹簧螺帽Strut Nuts兰花夹系列Toggle Bolts (Spring Toggle & Gravity Toggle)门窗、地板专用壁虎Nylon Frame Anchors or Metalframe Anchors石膏板中空壁虎Hollow Wall Anchors套管式壁虎Sleeve Anchors打入式壁虎鱼形尼龙壁虎Nylon Frame Harmmer Fixing (Nylon Hammer Drive Anchors) 强力式锤钉壁虎Hit Anchors电梯壁虎Bolt Anchors重载壁虎Heavy duty anchors两片夹Loxin Masonry Anchors定位螺栓Set Bolts长型兰花夹Short Strap Anchors工具棒Drop in Setting Tools象脚壁虎Elephant foot anchors水泥预埋件Concrete Insert翻边胀轴Drop in Anchor with Lip冲件Legs Drywall Anchors六角盖头螺帽Hex Cap Nuts六角锯齿螺帽Hex Serrated Nuts六角轮缘螺帽Hex Flange Nuts高脚螺帽Hex Coupling Nuts(High Nuts)圆螺帽Round Nuts四角螺帽Square Nuts管用螺帽Pipe Nuts轮壳螺帽Wheel Nuts蝶型螺帽Wing NutsU形螺帽U NutsT形螺帽T Nuts环首螺帽Eye Nuts齿形螺帽Kep Nuts齿花螺帽Clinch Nuts耐候钢六角重型螺帽Corten Steel Heavy Hex Nuts焊接螺帽Weld Nuts高张力螺帽Heigh Strength Nuts建业用螺帽Structural Nuts不锈钢螺帽Stainless Steel Nuts铜螺帽Brass Nuts铝螺帽Aluminum Nuts合金钢螺帽Alloy Steel Nuts重型车螺帽Heavy Duty Wheel Hub Nuts铁器焊接袋帽Acorn Cap Nuts金属预置扭矩式螺帽All-Metal Prevailing Torque Type Nuts壁虎螺帽Anchor Nuts大尺寸螺帽Big Size Nuts铁盖袋帽Closed End Acorn Nuts盘形华司螺帽Conical Washer Nuts铁盖+尼龙圈组合盖帽Din 986 Domed Cap Nuts突缘尼龙盖帽Flange Nylon Insert Lock Nuts平面华司螺帽Flat Waser Nuts六角割沟螺帽Hex Slotted Nut自锁螺帽Self-Locking Nuts制止螺帽Sliding NutsSln-自动防松螺帽Sln Self-Locking Nuts其它特殊螺帽Special Nuts弹簧螺帽Spring Nuts不锈钢突缘螺帽Stainless Steel Flange Nuts不锈钢六角轮缘尼龙螺帽Stainless Steel Flange Nylon Insert Lock Nuts 不锈钢六角重型螺帽Stainless Steel Heavy Hex Nuts不锈钢六角螺帽Stainless Steel Hex Nuts不锈钢尼龙嵌入螺帽Stainless Steel Nylon Insert Lock Nuts普通六角螺帽Hex Nuts六角重型螺帽Heavy Hex Nuts薄型螺帽Hex Jam Nuts尼龙嵌入防松螺帽Nylon Insert Lock Nuts机械螺丝用六角螺帽Hex Machine Screw Nut六角螺丝(栓) Hex Head Cap Screws(Hex Bolts)六角机械螺丝Hex Head Machine Bolts六角木牙螺丝Hex Lag Bolts四角螺丝Square Head BoltsT头螺丝T Head Bolts马车螺丝Carriage Bolts环首螺丝Eye Bolts内六角孔螺丝Hex Socket Cap Screws固定螺丝Set Screws螺椿栓Stud Bolts螺旋椿Screw Studs轮壳螺栓Wheel Bolts翼形螺丝Wing Screws自攻螺丝Self Tapping Screws自削螺丝Thread Cutting Screws钻尾螺丝Self Drilling Screws旋入螺丝Drive Screws机械螺丝Machine Screws木螺丝Wood Screws家具螺丝Furniture Screws塑板螺丝Chipboard Screws墙用螺丝Drywall Screws基础螺栓Foundation BoltsU型螺栓U Bolts勾头螺栓Hook Bolts套挂螺丝Toggle Bolts突缘螺丝Flange Bolts轨道螺栓(鱼尾螺丝) Track Bolts耐候钢螺丝Corten Steel Heavy Hex Bolts扭矩控制螺栓T.C.Bolts高张力螺栓High Strength Bolts剪力钉(焊接螺丝) Welding Studs螺丝附华司组合Screws And Washers Assembled(Sems)大尺寸螺栓Big Size Bolts不锈钢小螺丝Stainless Steel Sheet Metal Screws不锈钢大螺丝Stainless Steel Bolts铜螺丝Brass Screws铝螺丝Aluminum Screws合金钢螺丝Alloy Steel Screws电子螺丝Electronic Screws微小精密螺丝Micro Screws塑料螺丝Plastic Screws复合材料用螺丝Particle Board Screws钛合金螺丝Titanium Alloy Bolts钛、锆、钼、铌等螺丝、零件、材料Ti,Zr,Mo,Nb Pare Metal Bolts Parts 拇指螺丝Thumb Screws双头牙螺丝Double End Screws Hanger Bolt车辆(汽车)螺丝、螺帽Automotive Fasteners航天用螺丝Aerospace Fasteners飞机特殊扣件Source Control Bolts拉栓Blind Bolts面板螺丝Panel Fasteners电梯螺丝Elevator Bolts四角头固定螺丝Square Set Screws大头马车螺丝Step Bolts单向螺丝One Way Lag Screws管夹螺丝Hose Clamp Screws不锈钢固定螺丝Stainless Steel Hex Socket Cap Screws 不锈钢内六角螺丝Stainless Steel Hex Socket Cap Screws 铰链螺丝Hinge Screws货柜螺丝Container Screws复合材料钻尾螺丝Bi-Metal Self Drilling Screws三角牙螺丝Trilobular Thread Screws高低牙螺丝High Low Screws夹板用螺丝Particle Board Screws马桶螺丝Toilet Closet Bolts特长螺丝Special Longer Screws建业螺丝Building Fasteners不锈钢六角螺丝Stainless Steel Hex Socket Cap Screws 其它特殊螺丝Special Screws Or Bolts不锈钢特殊螺丝Special Stainless Steel Screws宽牙螺丝（粗牙螺丝）Coarse Thread Screws链带螺丝Collated Screws水泥螺丝Concrete Screws板模螺丝Construction Bolts锌蝶螺丝Die Cast Wing Screws; Zinc Alloy重型车螺丝Heavy Duty Wheel Hub Bolts内六角固定螺丝Hex Socket Set Screws复合材料用螺丝（夹板用）Particle Board Screws犁壁螺丝Plow Bolts不锈钢木螺丝Stainless Steel Wood Screws套挂螺栓及螺丝Toggle Bolts钛合金膨胀螺丝Titanium Alloy Expansion Bolts六角盖头螺帽Hex Cap Nuts六角锯齿螺帽Hex Serrated Nuts六角轮缘螺帽Hex Flange Nuts高脚螺帽Hex Coupling Nuts(High Nuts)圆螺帽Round Nuts四角螺帽Square Nuts管用螺帽Pipe Nuts轮壳螺帽Wheel Nuts蝶型螺帽Wing NutsU形螺帽U NutsT形螺帽T Nuts环首螺帽Eye Nuts齿形螺帽Kep Nuts齿花螺帽Clinch Nuts耐候钢六角重型螺帽Corten Steel Heavy Hex Nuts焊接螺帽Weld Nuts高张力螺帽Heigh Strength Nuts建业用螺帽Structural Nuts不锈钢螺帽Stainless Steel Nuts铜螺帽Brass Nuts铝螺帽Aluminum Nuts合金钢螺帽Alloy Steel Nuts重型车螺帽Heavy Duty Wheel Hub Nuts铁器焊接袋帽Acorn Cap Nuts金属预置扭矩式螺帽All-Metal Prevailing Torque Type Nuts壁虎螺帽Anchor Nuts大尺寸螺帽Big Size Nuts铁盖袋帽Closed End Acorn Nuts盘形华司螺帽Conical Washer Nuts铁盖+尼龙圈组合盖帽Din 986 Domed Cap Nuts突缘尼龙盖帽Flange Nylon Insert Lock Nuts平面华司螺帽Flat Waser Nuts六角割沟螺帽Hex Slotted Nut自锁螺帽Self-Locking Nuts制止螺帽Sliding NutsSln-自动防松螺帽Sln Self-Locking Nuts其它特殊螺帽Special Nuts弹簧螺帽Spring Nuts不锈钢突缘螺帽Stainless Steel Flange Nuts不锈钢六角轮缘尼龙螺帽Stainless Steel Flange Nylon Insert Lock Nuts 不锈钢六角重型螺帽Stainless Steel Heavy Hex Nuts不锈钢六角螺帽Stainless Steel Hex Nuts不锈钢尼龙嵌入螺帽Stainless Steel Nylon Insert Lock Nuts锌压属螺帽Zinc Die Casting Nuts普通六角螺帽Hex Nuts六角重型螺帽Heavy Hex Nuts薄型螺帽Hex Jam Nuts尼龙嵌入防松螺帽Nylon Insert Lock Nuts机械螺丝用六角螺帽Hex Machine Screw Nut合金钢线材盘元Alloy Steel Wire Rod球状化线材Annealing Wire And Rod黑铁丝Black Wire黄铜棒线Brass Wire And Rod磨光棒钢Bright Steel Bar(Hex/Round/Square)铜合金线Copper Alloy Wire线切割线E.D.M Cutting Wire快削钢线材盘元Free Cutting Steel Wire Rod线材Iron Or Steel Wire线材盘元Iron Or Steel Wire Rod洋白铜线Nickel Silver Wire磷青铜线Phosphate Bronze Wire不锈钢条棒Stainless Steel Bar(Round/Hex/Square)不锈钢冷锻线材Stainless Steel Cold Heading Wire不锈钢线(抽线后) Stainless Steel Draw Wire不锈钢线材Stainless Steel Wire不锈钢线材及盘元Stainless Steel Wire And Rod棒钢Steel Bar(Hex/Round/Square)转回90度碾线头机90讧evolving Wire Twisting Machine气动拉钉机Air Riveter各式螺丝类产品自动包装Automatic Packaging For All Kinds Of Packaging 自动包装机Automatic Packing Machine螺丝制造搓牙机械Automatic Thread Rolling Machine螺丝割尾加工机械Automatic Thread Slotting Machine螺丝制造成型机械Automatic Trimming Machine拉钉打头机Blind Rivet Heading Machine螺丝、螺帽成型机Bolt Formers,Nuts Formers,Headers螺丝、螺帽热处理Bolt Nut And Screws Heat Treatment螺丝、螺帽热处理炉Bolt Nut And Screws Heat Treatment Furnaces球状化电器炖炉Carburizing Furnace Vacuum And Bell Type Furnace超防锈复合瓷膜Ceramic Coating连续式光辉渗碳淬火炉Continuous Bright Carburizing Quenching Furnace 连续式光辉调质淬火炉Continuous Bright Hardening Quenching Furnace 中、高热镀锌光辉连续炉Continuous Bright Heat Treat Furnace连续式光辉热处理炉Continuous Type Bright Heat Treatment Furnace螺丝割尾及特殊割遘加工Machine Screw Shank Slotting螺丝钻孔加工Screw Shank Drilling鸡眼上下模Eyelets Dies一般线材、盘元、退火炉General Wire,Wire Rod,Annealing Furnace倒立式滑落型伸线机Handstand Type Wire Drawing Machine十字冲模Header Punches In Various Drives成型冲模Header Punches In Various Drives螺丝打头机Heading Machine螺丝制造高速搓牙机械High Speed Automatic Thread Rolling Machine高中低周波感应加热炉High,Medium,Low Frequency Induction Heater空心打头机Hollow Heading Machine热浸镀锌螺丝、螺帽Hot Dip Galvanizing Bolts And Nuts机械镀锌Mechanical Galvanized迷你成型机Mini-Formers成品自动收线机Non-Stop Coiler精抽自动收线机Non-Stop Coiler(Skinpass)螺帽模Nut Forming Dies螺帽成型模Nuts Formers特殊零件成型机Parts Forming Maching冲模Punch Dies冲子Punch Pins罗拉成型机Rollers Formers机(踏)车用螺丝成型机Screw For Motorcycle Or Bicycle Heading Machine止付螺丝成型机Set Screws Formers套高成型机Sockets Formers一般线材、盘元、螺丝合金炖炉Spheroidizing Bright Annealing Furnace球状化热处理炉Spheroidizing Heat Treatment Furnace攻牙机Tapping Machine螺丝攻、车刀、模具Taps Dies And Tools搓牙机铁屑分离装置Thread Chip Separator滚牙轮Thread Rolling Dies牙板Thread Rolling Dies Plates精密油压滚牙机Hydraulic Thread Rolling Machines模具Tools六角整头模Trimming Dies Hexagan碳化钨模具Tungsten Carbide Die镀钛处理(Tin)专业加工服务Tin Hard Coating For Cutting Tools And Punch By Pvd 电镀化学原料Various Electroplating Chemicals环规校正Calibration For Ring Gage环规、牙规、三线规校正Calibration For Ring Gage, Athread Gage, 3 Wire Gage 螺丝、螺帽品检量测仪器Fasteners Inspection And Measurement Instruments螺丝、螺帽成型攻牙专用油Forming And Tapping Oils For Bolts And Nuts Formers 螺丝、螺帽五金等检验Insptection Services For Fasteners And Hardware德国schatz扭力机代理Representative Of Schatz Torque MachinIso品质保证系统Iso Quality Assurance System生产管理系统Production Control System物料管理系统Material Control System齿轮Gears不锈钢牙条棒Stainless Steel Hread Rod马达轴承轴心组件Bearing Shaft(Motor)轴承轴心Bearing Shaft开口铆钉Blind Rivets长形拉帽Blind Rivet Nuts拉帽Blind Nuts拉钉Blind Rivets实心梢Clevis Pins And Straight Pins弹片Clips卷钉Coil Nails冷锻零件Cold Forming Part开口销Cotter PinsE型环E-Rings膨胀螺栓Expansion Anchor Bolts鸡眼钉Eyelets RivetsR型销Snap Pins闸、锁Latches And Keeper Assembleds其它特殊铆钉Other Specil Rivets销Pins格式管夹、管束Pipe Hanger铆钉Rivets螺旋锔及螺旋圈Screw Hook And Screw Rings中空钉Semi-Tubular Rivet开叉钉Split Drive Anchors弹簧华司Spring Washers弹簧蝴蝶夹Spring Wings不锈钢华司Stainlesssteel Washers钢铁钉Steel And Iron Nails搓牙铁钉Thread Nails钛合金铆钉Titaium Alloy Rivets管形铆钉Tubular Rivets华司Washers真空热处理Vacuum Heat Treatment螺丝、螺帽、五金、Diy扣件Fasteners合金钢工具Alloy Steel Tools螺栓模Bolt Heading Dies手动拉钉钳Hand Riveter船舶链Anchor Chain脚踏车链锁Bicycle Chain Locks螺丝起子Bit罗拉Chain Roller特殊铆合扣件Collars(A Blindfastener For Huck Intl)装饰链Decorative Chains自攻螺纹衬套Ensat Threaded Inserts六角扳手Hexagon Keys超音螺纹压入式螺纹自动锁扣Threaded Inserts For Plastic Injection Mouldeings 汽车特殊杆接件Special Auto-Mobile Fastener As Your Needs螺纹护套Recoil Inserts链条用滚子Roller For Roller Chain金属板镶嵌组件及自动夹扣组件Sheet Metal Fasteners工具套筒组件Socket Wrench Sets不锈钢链Stainless Steel Chains轭子T-Yoke轮胎链Tire Chains狗链Dog Chains喇叭头轭铁U-Yoke,T-Yoke For Speaker不锈钢输送带轮用轨道Stainless Wheel's Rack For Transporter工业用链Industrial Steel Link Chains拖链安全链Tow Chains And Safety Chains机车离合器零件Manufacture Of Motorcycle's Cvt Parts牙条棒Thread Rod机(踏)车用螺丝、轴心Screws And Shafts For Motorcycle Or Bicycle 针车用螺丝、轴心Screws And Shafts For Sewing Maching止付螺丝Socket Set Screws不锈钢宽牙螺丝Stainless Steel Coarse Thread Screws不锈钢高低牙螺丝Stainless Steel High-Low Thread Screws不锈钢机械螺丝Stainless Steel Machine Screws不锈钢钻尾螺丝Stainless Steel Self Drilling Screws不锈钢自攻螺丝Stainless Steel Self Tapping Screws不锈钢自削螺丝Stainless Steel Thread Cutting Screws不锈钢三角牙螺丝Stainless Steel Tri-Lobular Thread Screws。

紧固件类英语词汇/discuz/archiver/tid-81740.html白铁盖螺丝A2(18-8)Cap Screws水平调整螺丝Adjusted levelingscrews航天扣件Aerospace Fasteners合金钢螺丝(栓) alloy steel screws (bolts)铝螺丝aluminum screws车辆(汽车)螺丝、螺帽automotive fasteners复含材料钻尾螺丝bi-metal self drilling screws大尺寸螺丝big size bolts公母螺丝组BINDER POST & Screw set拉栓blind bolts铜螺丝(栓) brass screws (bolts)建筑螺丝building fasteners建筑膨涨螺丝building wall anchor半圆头六角孔螺丝button head socket cap screws马车螺丝carriage bolts活动轮螺丝附件castors fittings塑板螺丝chipboard screws快速钉紧螺丝及螺帽clinch studs & nuts挤压扣件clinching fasteners齿花扣件clinching parts宽牙螺丝coarse thread screws链带螺丝collated screws水泥螺丝concrete screws板模扣件construction fasteners货柜螺丝container screws耐候钢螺丝conten steel heavy hex bolts鱼尾螺丝conten steel oval neck track bolts双刀螺丝cutter screws匣板螺丝deck screws锌蝶螺丝die cast wing screws;zinc alloy双头牙螺丝double end screws, hanger bolt旋锁螺丝drive lock screws旋入螺丝drive screws墙用螺丝drywall screws ejot delta pt screws ejot pt screws 电子螺丝electronic screws电梯螺丝elevator bolts欧洲螺丝euro screws环首螺丝eye bolts冈山头螺丝fillister screws 鳍头螺丝fin neck round head bolts 管配件接头fitting fasteners (connectors) 突缘螺丝flange bolts (screws) 平头六角孔螺丝flat head socket cap screws 平纺螺丝flat pan head screws 地板螺丝flooring panel screws 基础螺丝foundation bolts 框架支撑螺丝frame anchor-lag round screws 家俱螺丝furniture screws (connecting bolts) 重型车螺丝、螺帽heavy duty wheel hub bolts & nuts 六角螺丝(栓) hex head cap screws (hex bolts) 六角机械螺丝hex head machine bolts 六角木牙螺丝hex lag bolts 内六角孔螺丝hex socket cap screws 等高螺丝hex socket head shoulder screw薄头强力螺丝hex socket low head cap screw 内六角固定螺丝hex socket set screws 华司头机械螺丝hex washer head machine screws 高低牙螺丝high low thread screws 高张力螺丝hex socket head shoulder screw 铰链螺丝hinge screws 勾头螺栓hook bolts 管夹螺丝hose clamp screws 哈克钉huck bolts 旋锁螺丝ktx locking recess screws 机械螺丝machine screws mdf螺丝mdf screws 微小精密螺丝micro screws 钼六角螺丝mo hex head cap screws 钼nc螺丝mo nc fasteners 钼螺帽mo nuts 镍合金螺丝monel fasteners 多冲程螺丝multi-stage screw & parts 利革钉nylon plug & screws 单向螺丝one way lag screws 枋头中心螺丝pan head center bolts 面板螺丝panel fasteners 复合材料用螺丝(夹板用) particle board screws 贯穿螺丝penetrate screws 十字四角复合螺丝ph+sq combination screws 塑料螺丝plastic screws 犁壁螺丝plow bolts 特殊精密螺丝precision axis and special fasteners 卷带螺丝roll collated screws 屋顶螺丝roofing screws 螺旋椿screw studs 机(踏)车用螺丝.轴心screws & shafts for motorcycle or bicycle 针车用螺丝.轴心screws & shafts for sewing machine 螺丝附华司组合screws & washers assembled (sems) 安全螺丝security screws 钻尾螺丝self drilling screws 自攻螺丝self tapping screws 固定螺丝screws & shafts for sewing machine剪力钉shear concrete stud 束肩螺丝(栓) shoulder screws (bolts) 一字沟槽固定螺丝slotted set screws 止付螺丝socket set screws 飞机特殊扣件source control bolts 特殊涂装螺丝special coating screws 特长螺丝special longer screws 特殊材质螺丝special material screws 特殊螺丝special screws or bolts 特殊防松螺丝special self-locking screws 不锈钢特殊螺丝special stainless steel screws 特殊割尾螺丝special thread cutting screws 四角螺丝square head bolts 四角头固定螺丝square head set screws 不锈钢大螺丝stainless steel bolts 不锈钢塑板螺丝stainless steel chipboard screws 不锈钢粗牙螺丝stainless steel coarse thread screws 不锈钢旋入螺丝stainless steel drive screws 不锈钢平头内六角孔螺丝stainless steel flat head socket cap screws 不锈钢六角螺丝stainless steel hex head cap screws 不锈钢内六角螺丝stainless steel hex socket cap screws 不锈钢固定螺丝stainless steel hex socket set screws 不锈钢高低牙螺丝stainless steel high-low thread screws 不锈钢机械螺丝stainless steel machine screws 不锈钢小螺丝stainless steel screws 不锈钢钻尾螺丝stainless steel self drilling screws 不锈钢自攻螺丝stainless steel self tapping screws 不锈钢sems 螺丝stainless steel sems screws 不锈钢自削螺丝stainless steel thread cutting screws 不锈钢牙条棒stainless steel thread rod 不锈钢三角牙螺丝stainless steel triangular screw thread 不锈钢木螺丝stainless steel wood screws 卡锁壁虎steel locking anchor 大头马车螺丝step bolts 螺桩栓stud bolts t头螺丝t head bolts 扭矩控制螺栓t.c. bolts (tension control bolts) 自削螺丝thread cutting screws 牙条棒thread rod 姆指螺丝thumb screws 钛合金自行车螺丝titanium -6al –4r alloy fasteners 钛合金螺丝titanium alloy bolts 钛六角螺丝titanium hex head cap screws (hex bolts) 钛nc螺丝titanium nc fasteners 钛止付螺丝titanium set screws 钛内六角孔螺丝titanium socket cap screws 钛牙条titanium thread rod 套挂螺丝toggle bolts 套挂螺栓及螺丝toggle bolts & acoustical lag (screweye) 马桶螺丝toilet closet bolts torx screws torx screws 轨道螺栓(鱼尾螺丝) track bolts 三角牙螺丝triangular screws thread u型螺栓u bolts 直立轴螺丝vertical shaft screws 焊接螺丝weld studs,screws,bolts 焊点螺丝weld studs screws 轮毂螺栓wheel bolts 车轮轴螺丝,螺帽wheel hub bolts and nuts 窗户螺丝window screws 翼形螺丝wing screws 木螺丝wood screws 锆螺丝zr fasteners set screws set screws high strength bolts high strength bolts 铁盖焊接袋帽acorn cap nuts 金属预置扭矩式螺帽all-metal prevailing torque type nuts 合金钢螺帽alloy steel nuts 铝螺帽aluminum nuts 壁虎螺帽anchor nuts 圆柱帽barrel nuts (cross dowel) 大尺寸螺帽big size nuts 铜螺帽brass nuts 四角多用途螺帽cage nuts 袋帽cap nuts 城堡螺帽castle nuts 齿花螺帽clinch nuts 铁盖袋帽closed end acorn nuts 盘形华司+袋帽螺帽conical washer and cap nuts 盘形华司螺帽conical washer nuts 耐候钢六角重型螺帽corten steel heavy hex nuts 长螺帽coupling nuts 铁盖+尼龙圈组合盖帽din 986 domed cap nuts 碟锁防松脱螺帽disk-lock nuts 企眼螺帽eye coupling nuts 环首螺帽eye nuts 突缘尼龙螺帽flange nylon insert lock nuts 平面华司螺帽flat washer nuts 齿轮gears六角重型螺帽heavy hex nuts 六角盖头螺帽hex cap nuts 六角突缘螺帽hex flange nuts 薄型螺帽hex jam nuts 薄型电子六角螺帽hex jam nuts (for electronic) 机械螺丝用六角螺帽hex machine screw nut 普通六角螺帽hex nuts 六角锯齿螺帽hex serrated nuts 双头内牙螺帽hex (reducer )coupling nuts 高螺帽high nuts 高张力螺帽high strength nuts 内外牙螺母(拉帽) insert nuts jcn nuts jcn nuts 齿形螺帽kep nuts 防松螺帽lock nuts 长螺帽long nuts 机车用螺帽nuts for motorcycle 面板螺帽nuts plate 尼龙袋帽nylon cap insert lock nuts 尼龙嵌入防松螺帽nylon insert lock nuts 马桶螺帽open end acorn nuts 卡车轮胎螺帽outer cap nuts 管用螺帽pipe nuts 塑料螺帽plastic nuts pop nuts pop nuts 抑制螺帽prevailing torgue nut 快速扣件push nut fasteners 长方形螺帽(薄型) rectangle jam nuts 长方四角螺帽rectangle square nuts 圆螺帽round nuts 自锁螺帽self-locking nuts 制止螺帽sliding nuts sln-自锁防松螺帽sln self-locking nuts 沟槽螺帽slotted nuts 特殊螺帽special nuts 特殊轮毂螺帽special wheel nuts 弹簧螺帽spring nuts 薄型四角螺帽square jam nuts 四角螺帽square nuts 不锈钢突缘螺帽stainless steel flange nuts 不锈钢六角突缘尼龙螺帽stainless steel flange nylon insert lock nuts 不锈钢六角重型螺帽stainless steel heavy hex nuts 不锈钢六角螺帽stainless steel hex nuts 不锈钢螺帽stainless steel nuts 不锈钢尼龙嵌入螺帽stainless steel nylon insert lock nuts不锈钢四角螺帽stainless steel square nuts 建筑用螺帽structural nuts t形螺帽t nuts 塑料品之埋植铜,铝螺帽threaded inserts for plastic injection mouldings 钛螺帽titanium nuts 压边螺帽+盘形华司组合top lock nut with conical washer assemble u形螺帽u nuts 焊接螺帽weld nuts 轮毂螺帽wheel nuts 蝶形螺帽wing nuts 锌压铸螺帽zinc die casting nuts 铝钉aluminum nails 马达轴承轴心组件bearing shaft（motor）轴承轴心bearing shaft 开口铆钉bifurcated rivets 长形拉帽（长型螺帽）binder posts（anchor nuts）拉帽blind nuts (rivet nuts) 拉钉blind rivets 电梯壁虎bolt anchor 金属黏着橡胶华司（双层华司）bonded washers 铜钉brass nails c型扣环c-rings 小眼钉ceiling hanger 化学壁虎chemical stud 实心梢clevis pins & straight pins 弹片clips 卷钉coil nails 冷锻零件cold forming part 开口梢cotter pins 洋钉钩cup hooks 弧型华司curved washer 外迫壁虎cut anchor 插梢dowel pin 捶钉drive rivet 壁虎drop in anchor e型环e-rings 膨胀螺栓expansion anchor bolts 难眼钉eyelets rivets 门钩gate hooks 插沟销grooved pins 有槽钢钉grooved steel nails 火药钉gunpowder nails 壁钩hardwall hangers 双片夹壁虎heavy duty shield anchor r型梢hitch pins（snap pins）空心钉hollow rivets 洋钉iron nails j钩j hook k.d. fitting k.d. fitting 闩锁latches & keeper assembleds 多冲程铆钉multi-stage rivers 锤钉壁虎nail in anchor 尼龙壁虎nylon (metal) frame anchor 塑料华司nylon washers 其它特殊铆钉other special rivets样品钩pegboard hook 吊图钩picture hangers 梢pins 各式管夹,管束pipe hanger 管塞pipe plug 塑料壁虎plastic nylon anchors pop拉钉系列产品pop rivets 快速插销quick release pins r型扣环r-rings 扣环rings 铆钉rivets 圆棒铁钉round iron nails t型铁钉round iron tape t nail 圆棒钢钉round steel nails t型钢钉round steel tape t nails u型钢钉round steel tape u nails 橡胶华司rubber washers s钩s hooks s型扣环s-rings 螺旋铝钉screw aluminum nails 螺旋环(洋眼) screw eyes 螺旋钩及螺旋圈screw hook & screw rings 螺丝钩screw hooks 螺旋铁钉screw iron nails 螺旋钢钉screw steel nails 中空铆钉semi-tubular rivet 套管壁虎sleeve anchor 实心铆钉solid rivets 特殊华司special washers 快速铆接扣件speed riveting 开叉钉split drive anchors 弹簧梢spring pin 弹簧华司spring washers 弹簧蝴蝶夹spring wings 折钉square hooks 不锈钢钢钉stainless steel nails 不锈钢中空钉stainless steel semi-tubular rivet 不锈钢斜纹钉stainless steel slanting stripes nails 不锈钢华司stainless steel washers 钢铁钉steel & iron nails 钢钉steel nails l型钢钉steel tape l nails 铁马钩storage hook 吸盘钩suction hangers 兰花钩swag hooks 三角吊钩swivel loop hangers 地毯钢钉tacked iron nails搓牙铁钉thread nails 大眼钉tie wire spade stud 钛合金铆钉titanium alloy rivets 钛合金膨涨螺丝titanium alloy expansion bolts 钛华司titanium washers 齿型华司tooth lock washers 管形铆钉tubular rivets 双向迫紧器turnbuckle 节牙钢钉w/strip steel nails 华司washers 波浪型华司wave washer 拉涨壁虎wedge anchor 线圈wire 锌合金壁虎zinc alloy frame anchor 螺丝,螺帽,五金,diy扣件all kinds of pacd aging series 合金钢工具alloy steel tools 电子手把handles for electronic devices 六角板手hexagon keys 螺丝起子power bit 螺丝起子screwdriver bit 电动螺丝起子autofeed screwdriver 工具套筒组件socket sets 套筒sockets 板手wrench 自动炼带螺丝枪autofeed screw driver 合金钢线材盘元alloy steel wire rod 铝合金锭aluminum alloy 球状化线材annealing wire & rod 黑铁丝black wire 黄铜棒线brass wire & rod 磨光棒钢bright steel bar (hex/round/square) 铜合金线copper alloy wire 线切割线e.d.m cutting wire 快削钢线材盘元free cutting steel wire rod 镀锌铁线galvanized steel wire 线材iron or steel wire 线材盘元iron or steel wire rod 洋白铜线nickel silver wire 磷青铜线phosphor bronze wire 各种表面处理用喷砂材料sand blasting materials 不锈钢条棒stainless steel bar (round/hex/square) 不锈钢冷锻线材stainless steel cold heading wire 不锈钢线(抽线后) stainless steel draw wire 不锈钢网线stainless steel net wire 不锈钢特殊线stainless steel special wire 不锈钢弹簧线stainless steel spring wire 不锈钢线材stainless steel wire 不锈钢线材及盘元stainless steel wire & rod 棒钢steel bar(hex/round/square) 钛、锆、钼、铌等螺丝、零件、材料ti、zr、mo、nb pare metal bolts parts 锌合金锭zinc alloy 立体/平面雕刻机3d die-sinking machine/engraving machine 转回90度辗线头机90°revolving wire twisting machine 干燥机air dryer 气动拉钉机air riveter 铝,低合金熔解热处理炉aluminum & low alloy melting furnace 铝散热器烧焊热处理炉aluminum brazing furnace for aluminum condenser 不锈钢线材连续式光辉热处理退火炉annealing furnace specially for stainless wire 小型脱油机anti-oil machine 自动包装机automatic packing machine 螺丝自动检查设备automatic screw sorting machine 自动送锁螺丝机automatic screwing machine 螺丝割尾加工机械automatic thread slotting machine 螺丝制造成型机械automatic trimming machine 箱式渗碳氮化炉batch type carburizing & mitriding furnace 钟罩式退火(球化)炉bell type spheroidizing annealing furnace 拉帽成型机blind nut formers 拉钉打头机blind rivet heading machine 螺丝(栓)成型机bolt formers 螺丝、螺帽成型机bolt formers, nut formers, headers 螺栓模bolt heading dies 螺丝、螺帽热处理bolt,nut & screws heat treatment 螺丝、螺帽热处理炉bolt,nut & screws heat treatment furnaces 圆剪式打头机bush cut-off heading machine 圆剪式空心打头机bush cut-off hollow heading machine 主模carbide dies 剪模carbide quills 不锈钢螺丝,扣件连续式光辉调质淬火炉carburizing furnace for stainless fastener 球状化电气炖炉carburizing furnace,vacuum & bell type furnace 流气式箱型炉(箱式,坑式,台车式,连续式) circulation furnace (box,pit,truck,continuous type) cnc计算机雕刻机cnc engraving machine 卷钉制造机coil nail collator 连续式光辉渗碳,淬火,回火炉continuous bright carburizing & hardening furnace 连续式光辉渗碳淬火炉continuous bright carburizing quenching furnace 连续式光辉调质淬火炉continuous bright hardening quenching furnace 中,高热镀锌光辉连续炉continuous bright heat treat furnace 连续式光辉热处理炉(不锈钢,硬焊) continuous bright treatment (for stainless,brazing) 连续式光辉热处理炉continuous type bright heat treatment furnace 耐腐蚀表面处理炉(耐炼) corrosion resistance of surface treatment furnace 剪刀(螺丝模) cut-off knives 集尘设备cyclone equipment 各种碳化钨制品设计制造design & manufacture of tungsten carbide products 模具dies & tools 钻尾模drill point dies 耐冲螺丝成型模具fastenerforming dies 螺丝、螺帽品检量测仪器fasteners inspection and measurements’instruments 精密过滤器filter 滚沟牙板flat knurling dies 一般线材,盘元,退火炉general wire,wire rod annealing furnace 手动拉钉钳hand riveter 倒立式滑落型伸线机handstand type wire drawing machine 白铁针header punches for stainless bolt 三角,四角,六角针header punches in various drives(1) 米字,一字,梅花,零号针header punches in various drives(2)一字六角边冲头header punches in various drives(3) 螺丝打头机heading machine 六角冲针hex pins 六角冲模hex recess punches 六角冲模hex trimming dies 螺丝制造高速搓牙机械high speed automatic thread rolling machine 高中低周波感应加热炉high,medium,low frequency induction heater 空心打头机hollow heading machine 热锻造机hot former 冲销knockout pins 雷射/影像筛选机laser/optical sorting machine for screws 立式输送机loader 机械螺丝牙板machine screw thread rolling dies plates 冲床用的冲具manufacture of punch for press die 螺丝,螺帽用的冲具manufacture of punch making bolts and nuts 迷你成型机mini-formers 铁钉滚牙机nail rolling machine 铁钉模具nails die 成品自动收线机non-stop coiler 精抽自动收线机non-stop coiler (skinpass) 螺帽模nut forming dies 螺帽成型机nuts formers 螺帽攻牙机nuts tapping machine 特殊零件成型机parts forming machine 脚踏板系列自动组立专用机pedal automatic assembling machine 十字四角复合针ph+sq combination punches 四角十字冲模十字冲模phillips punches 十字割沟冲模phillips slotted punches 冲针壳pin holders 锁用中心零件pins tailpiece 拋光机/磨光台polishing machine 手握式螺丝自动供给锁紧机portable screw-driving machine 粉末治金烧结,黑化炉powder metallurgy & steam treatment furnace 米字冲模pozi punches 冲模punch dies 冲子punch pins 冲针冲床引伸模具punching dies 罗拉成型机rollers formers rx,dx瓦斯变成炉,ax 氨气分解炉rx,dx gas generator,ax ammo gas generator 盐浴式热处理炉salt bath heat treatment furnace 各式表面处专用喷砂机sand blasting machine for surface treatment 螺丝自动组合华司机器screw & washer assembly machine for sems 机(踏)车用螺丝成型机screw for motorcycle or bicycle heading machine 螺丝夹尾模screws tail point dies 钻尾螺丝成型机self-drilling screw forming machine 钻尾模具self-drilling screw making dies 止付螺丝成型机set screws formers 梅花冲头six lobe punches 一字冲模slot punches 套筒成型机sockets formers 碳钢盘元,线材,球状化热处理退火炉spheroidizing annealing furnace for steel wire 一般线材,盘元,螺丝合金炖炉spheroidizing bright annealing furnace 球状化热理炉spheroidizing heat treatment furnace 四角孔针具sq punches 四角冲模square recess punches 不锈钢钻尾螺丝割尾stainless steel self drilling screw milled point 钻子tap 攻牙机tapping machine 自攻螺丝牙板tapping screw thread rolling dies plates 螺丝攻、车刀、模具taps dies & tools 铁氟龙(teflon)及珐琅烧付炉teflon coating furnace 搓牙机铁屑牙离装置thread chip separator 滚牙轮thread rolling dies 牙板thread rolling dies plates 螺丝搓手机thread rolling machine 精密油压滚牙机thread rolling machines 货物捆绑系统tie down hardware 弹簧机外围零件tooling peripheral component of spring machine 六角整头模trimming dies hexagon 碳化钨模具tungsten carbide die unilockself-locking and seal-locking unilock self-locking and seal-locking fasteners 电镀化学原料various electroplating chemicals 立式单双层连续伸线机vertical type single deck wire drawing machine 温锻造机warm former 伸线机wires drawer 特殊铆合扣件collars (a blind fastener for huck intl) 电器银接点contact point 螺丝diy包装系列diy screws packing series 自攻螺纹衬套ensat thread insert 螺丝、螺帽成型攻牙专用油forming& tapping oils for bolts & nuts formers 铰链hinges 热浸镀锌螺丝,螺帽hot dip galvanizing bolts & nuts 工业用炼industrial steel link chains 安全护套k-sert 机车离合器零件manufacture of motorcycle’s cvt parts 镜托mirror holders 螺丝套筒nut setters 尼龙头（用于螺丝头部）nylon head（for screws）尼龙圈（用于防松螺帽）nylon ring（for lock nuts）o.e.m. 组件o.e.m. parts 精密加工组件precise lathe cutting parts 精密车床零组件precision turning part 冲压零件punching parts 螺纹护套recoil inserts 轭铁(t型铁、u型铁) t-yoke,under yoke 喇叭头轭铁u-yoke,t-yoke for speaker 轮子零件wheel component 木螺丝牙板wood screw dies2005-11-16 22:30 315508161行业标准规范中英文对照系列之通用零部件(一)1 gb/t 2-1985 紧固件外螺纹零件的末端fasteners--ends of parts with external thread 2 gb/t 8-1988 方头螺栓c级square head bolts--product grade c 3 gb/t 10-1988 沉头方颈螺栓flat countersunk square neck bolts 4 gb/t 11-1988 沉头带榫螺栓flat countersunk nib bolts 5 gb/t 12-1988 半圆头方颈螺栓cup head square neck bolts 6 gb/t 13-1988 半圆头带榫螺栓cup head nib bolts 7 gb/t15-1988 大半圆头带榫螺栓cup head nib bolts with large head 8 gb/t 22-1976 小六角头导颈螺栓bolts, small hexagon head with fit neck 9 gb/t 23-1976 小六角头螺杆带孔螺栓bolts, small hexagon head with hole through the shank 10 gb/t 24-1976 小六角头螺杆带孔导颈螺栓Bolts, small hexagon head with fit neck and hole through the shank11 GB/T25-1976 小六角头头部带孔螺栓Bolts, small hexagon head with holes through the head 12 GB/T 26-1976 小六角头头部带孔导颈螺栓Bolts, small hexagon head with fit neck and holes through the head 13 GB/T 27-1988 六角头铰制孔用螺栓A和B级Hexagon fit bolts--Product grade A and B 14 GB/T 28-1988 六角头螺杆带孔铰制孔用螺栓A和B级Hexagon fit bolts with Split pin hole on shank--Product grade A and B 15 GB/T 29.1-1988六角头头部带槽螺栓A和B级Hexagon bolts with slot on head--Product grade A and B 16 GB/T 29.2-1988 十字槽凹穴六角头螺栓Cross recessed hexagon bolts with indentation 17 GB/T 31.1-1988 六角头螺杆带孔螺栓A和B级Hexagon bolts with split pin hole on shank--Product grade A and B 18 GB/T 31.2-1988 六角头螺杆带孔螺栓细杆B级Hexagon bolts with split pin hole on shank--Reduced shank--Product grade B 19 GB/T31.3-1988 六角头螺杆带孔螺栓细牙A和B级Hexagon bolts with split pin hole on shank--Fine pitch thread--Product grade A and B 20 GB/T 32.1-1988 六角头头部带孔螺栓A和B级Hexagon bolts with wire holes on head--Product grade A and B 21 GB/T 32.2-1988 六角头头部带孔螺栓细杆B级Hexagon bolts with wire holes on head--Reducedshank--Product grade B 22 GB/T 32.3-1988 六角头头部带孔螺栓细牙A和B级Hexagon bolts with wire holes on head--Fine pitch thread--Product grade A and B 23 GB/T 35-1988 小方头螺栓B级Square head bolts with small head--Product grade B 24 GB/T 37-1988 T型槽用螺栓Bolts for T-Slot 25 GB/T 38-1976 螺栓技术条件Bolts--Technical requirements 26 GB/T 39-1988 方螺母C级Square nuts--Product grade C 27 GB/T41-1986 1 型六角螺母C 级Hexagon nuts--Style 1--Product grad C 28 GB/T 56-1988 六角厚螺母Hexagon thick nuts 29 GB/T 61-1976 螺母技术条件Nuts--Technical requirements 30 GB/T 62-1988 蝶形螺母Wing nuts31 GB/T 63-1988 环形螺母Lifting nuts 32 GB/T 65-1985 开槽圆柱头螺钉Slotted cheese head screws 33 GB/T 67-1985 开槽盘头螺钉Slotted pan head screws 34 GB/T 68-1985 开槽沉头螺钉Slotted countersunk head screws 35 GB/T 69-1985 开槽半沉头螺钉Slotted raised countersunk head screws 36 GB/T 70-1985 内六角圆柱头螺钉Hexagon socket cap head screws 37 GB/T 71-1985 开槽锥端紧定螺钉Slotted set screws with cone point 38 GB/T 72-1988 开槽锥端定位螺钉Slotted set screws with cone point 39 GB/T 73-1985 开槽平端紧定螺钉Slotted set screws with flat point 40 GB/T 74-1985 开槽凹端紧定螺钉Slotted set screws with cup point41 GB/T 75-1985 开槽长圆柱端紧定螺钉Slotted set screws withlong dog point 42 GB/T77-1985 内六角平端紧定螺钉Hexagon socket set screws with flat point 43 GB/T 78-1985 内六角锥端紧定螺钉Hexagon socket set screws with cone point 44 GB/T 79-1985 内六角圆柱端紧定螺钉Hexagon socket set screws with dog point 45 GB/T 80-1985 内六角凹端紧定螺钉Hexagon socket set screws with cup point 46 GB/T 83-1988 方头长圆柱球面端紧定螺钉Square set screws with long dog point and rounded end 47 GB/T 84-1988 方头凹端紧定螺钉Square set screws with cup point 48 GB/T 85-1988 方头长圆柱端紧定螺钉Square set screws with long dog point 49 GB/T 86-1988 方头短圆柱锥端紧定螺钉Square set screws with short dog point and cone end 50 GB/T 89-1976 螺钉技术条件Screws--Technical requirements51 GB/T 90-1985 紧固件验收检查、标志与包装Acceptance inspection,marking and packaging of fasteners 52 GB/T 91-1986 开口销Split pins 53 GB/T 93-1987 标准型弹簧垫圈Single coil spring lock washers--Normal type 54 GB/T 94.1-1987 弹性垫圈技术条件弹簧垫圈Specifications for spring washers--Single coil spring lock washers 55 GB/T 94.2-1987 弹性垫圈技术条件齿形、锯齿锁紧垫圈Specifications for spring washers--Toothed lock and serrated lock washers 56 GB/T94.3-1987 弹性垫圈技术条件鞍形、波形弹性垫圈Specifications for springwashers--Curved and wave spring washers 57 GB/T 95-1985 平垫圈-C级Plainwashers--Product grade C 58 GB/T 272-1993 滚动轴承代号方法Rollingbearing--Identification code 59 GB/T 273.1-1987 滚动轴承圆锥滚子轴承外形尺寸方案Rolling bearings Tapered roller bearings--Boundary dimensions 60 GB/T 273.3-1988 滚动轴承向心轴承外形尺寸方案Rolling bearings Radial bearings—Boundary dimensions 61 GB/T 274-1991 滚动轴承装配倒角极限Rolling bearing chamfer dimension limits 62GB/T 275-1993 滚动轴承与轴和外壳的配合Shaft and housing fits for rolling bearings 63GB/T 276-1994 滚动轴承深沟球轴承外形尺寸Rolling bearings--Deep groove ball bearings--Boundary dimensions 64 GB/T 280-1964 带毡封圈的单列向心球轴承结构型式和基本尺寸Rolling bearings--Single-row radial ball bearings withfelt seals--Types and basic dimensions 65 GB/T 281-1994 滚动轴承调心球轴承外形尺寸Rollingbearings--Self-aligning ball bearings--Boundary dimensions 66 GB/T 283-1994 滚动轴承圆柱滚子轴承外形尺寸Rolling bearings--Cylindrical roller bearings—Boundary dimensions 67 GB/T 285-1994 滚动轴承双列圆柱滚子轴承外形尺寸Rolling bearings--Double row cylindrical roller bearings—Boundary dimensions 68 GB/T 286-1964 双列向心球面滚子轴承结构型式和基本尺寸Rolling bearings--Double -row radial spherical roller bearings--Types and basic dimensions 69 GB/T 288-1994 滚动轴承调心滚子轴承外形尺寸Rolling bearings--Self-aligning roller bearings—Boundary dimensions 70 GB/T 289-1964 滚针轴承结构型式和基本尺寸Needle roller bearings--Types and basic dimensions 71 GB/T 291-1964 螺旋滚子轴承结构型式和基本尺寸Rolling bearings with helically wound cylindrical rollers--Types and basic dimensions 72 GB/T 292-1994 滚动轴承角接触球轴承外形尺寸Rolling bearings--Angular contact ball bearings--Boundary dimensions 73 GB/T 294-1994 滚动轴承三点和四点接触球轴承外形尺寸Rolling bearings--Three point and four point contact ball bearings--Boundary dimensions 74 GB/T 296-1994 滚动轴承双列角接触球轴承外形尺寸Rolling bearings--Double row angular contact ball bearings--Boundary dimensions 75 GB/T 297-1994 滚动轴承圆锥滚子轴承外形尺寸Rolling bearings--Tapered roller bearings--Boundary dimensions 76 GB/T299-1995 滚动轴承双列圆锥滚子轴承外形尺寸Rolling bearings--Metric double row tapered roller bearings--Boundary dimensions 77 GB/T 300-1995 滚动轴承四列圆锥滚子轴承外形尺寸Rolling bearings--Four row tapered roller bearings--Boundary dimensions 78 GB/T 301-1995 滚动轴承推力球轴承外形尺寸Rolling bearings--Thrust ballbearings--Boundary dimensions 79 GB/T 304.1-1988 关节轴承分类Spherical plain bearings Classification 80 GB/T 304.2-1988 关节轴承代号方法Spherical plain bearings Identification code81 GB/T 304.3-1990 关节轴承配合Spherical plain bearings—Fits 82 GB/T 304.9-1981 向心关节轴承技术条件Spherical plain radial bearings, jointtype--Technical requirements 83 GB/T 304.10-1989 关节轴承公差Spherical plain bearings—Tolerances 84 GB/T 307.1-1994 滚动轴承向心轴承公差Rollingbearings--Radial bearings--Tolerances 85 GB/T 307.2-1995 滚动轴承测量和检验的原则及方法Rolling bearings--Measuring and gauging principles and methods 86 GB/T307.3-1996 滚动轴承通用技术规则Rolling bearings--General technical regulations 87 GB/T 307.4-1994 滚动轴承推力球轴承公差Rolling bearings--Thrust ballbearings--Tolerances 88 GB/T 308-1989 滚动轴承钢球Rolling bearings—Steel balls 89 GB/T 309-1984 滚动轴承滚针Rolling bearings--Needle rollers 90 GB/T 794-1993 加强半圆头方颈螺栓Strengthened cap head square neck bolts 91 GB/T 798-1988 活节螺栓Eye bolts 92 GB/T 799-1988 地脚螺栓Eyelet bolts 93 GB/T 800-1988 沉头双榫螺栓Flatcountersunk double nib bolts 94 GB/T 802-1988 组合式盖形螺母Acorn nuts 95 GB/T 804-1988 球面六角螺母Hexagon nuts with raised face 96 GB/T 805-1988 扣紧螺母Tight nuts 97 GB/T 806-1988 滚花高螺母Knurled nut with collar 98 GB/T 807-1988 滚花薄螺母Knurled nuts 99 GB/T 808-1988 小六角特扁细牙螺母Small hexagon thinnuts-Fine pitch thread 100 GB/T 809-1988 嵌装圆螺母Insert round nuts2005-11-16 22:32 315508161行业标准规范中英文对照系列之通用零部件(二)101 GB/T 810-1988 小圆螺母Small round nuts 102 GB/T 812-1988 圆螺母Round nuts 103 GB/T 815-1988 端面带孔圆螺母Round nuts with drilled holes in one face 104 GB/T 816-1988 侧面带孔圆螺母Round nuts with set pin holes in side 105 GB/T 817-1988 带槽圆螺母Slotted round nuts 106 GB/T 818-1985 十字槽盘头螺钉Cross recessed pan head screws 107 GB/T 819-1985 十字槽沉头螺钉Cross recessed countersunk head screws 108 GB/T 820-1985 十字槽半沉头螺钉Cross recessed raised countersunk head screws 109 GB/T 821-1988 方头倒角端紧定螺钉Square set screws with chamfered end 110 GB/T 822-1988 十字槽圆柱头螺钉Cross recessed cheese head serews 111 GB/T 823-1988 十字槽小盘头螺钉Cross recessed small pan head screws 112 GB/T 824-1976 圆柱头内花键螺钉Screws,fluted socket head 113 GB/T 825-1988 吊环螺钉Eyebolts 114 GB/T 827-1986 标牌铆钉Rivets for name plate 115 GB/T 828-1988 开槽盘头定位螺钉Slotted pan head set setscrews with dog point 116 GB/T 829-1988 开槽圆柱端定位螺钉Slotted setscrews with dog point 117 GB/T 830-1988 开槽圆柱头轴位螺钉Slotted cheese head screws with shoulder 118 GB/T 831-1988 开槽无头轴位螺钉Slotted shoulder screws 119 GB/T 832-1988 开槽带孔球面圆柱头螺钉Slotted capstan screws 120 GB/T 833-1988 开槽大圆柱头螺钉Slotted large cheese head screws121 GB/T 834-1988 滚花高头螺钉Knurled thumb screws 122 GB/T 835-1988 滚花平头螺钉Knurled screws 123 GB/T 836-1988 滚花小头螺钉Knurled screws with small head 124 GB/T 837-1988 开槽盘头不脱出螺钉Slotted pan head screws with waisted shank 125 GB/T 838-1988 六角头不脱出螺钉Hexagon screws with waisted shank 126 GB/T 839-1988 滚花头不脱出螺钉Knurled thumb screws with waisted shank 127 GB/T 840-1988 塑料滚花头螺钉Plastic diamond knurlhead screws 128 GB/T 845-1985 十字槽盘头自攻螺钉Cross recessed pan head tapping screws 129 GB/T 846-1985 十字槽沉头自攻螺钉Cross recessed countersunk head tapping screws 130 GB/T 847-1985 十字槽半沉头自攻螺钉Cross recessed raised countersunk head tapping screws 131 GB/T 848-1985 小垫圈--A级Plain washers--Small series--Product grade A 132 GB/T 849-1988 球面垫圈Weshers with ball face 133 GB/T 850-1988 锥面垫圈Washers with cone face 134 GB/T 851-1988 开口垫圈Washers with split 135 GB/T 852-1988 工字钢用方斜垫圈Square taper washers for I section 136 GB/T 853-1988 槽钢用方斜垫圈Square taper washers for slot section 137 GB/T 854-1988 单耳止动垫圈T ab washers with long tab 138 GB/T855-1988 双耳止动垫圈T ab washers with long tab and wing 139 GB/T 856-1988 外舌止动垫圈External tab washers 140 GB/T 858-1988 圆螺母用止动垫圈Tab washers for round nut141 GB/T 859-1987 轻型弹簧垫圈Single coil spring lock washers,Light type 142 GB/T 860-1987 鞍形弹性垫圈Curved spring washers 143 GB/T 861.1-1987 内齿锁紧垫圈Lock washers internal teeth 144 GB/T 861.2-1987 内锯齿锁紧垫圈Serrated lock washers internal teeth 145 GB/T 862.1-1987 外齿锁紧垫圈Lock washers external teeth 146 GB/T 862.2-1987 外锯齿锁紧垫圈Serrated lock washers external teeth 147 GB/T863.1-1986 半圆头铆钉(粗制) Round head rivets--Black 148 GB/T 863.2-1986 小半圆头铆钉(粗制) Round head rivets with small head--Black 149 GB/T 864-1986 平锥头铆钉(粗制) Cone head rivets--Black 150 GB/T 865-1986 沉头铆钉(粗制) Countersunk head rivets-Black151 GB/T 866-1986 半沉头铆钉(粗制) Oval countersunk head rivets--Black 152 GB/T 867-1986 半圆头铆钉Round head rivets 153 GB/T 868-1986 平锥头铆钉Cone head rivets 154 GB/T 869-1986 沉头铆钉Countersunk head rivets 155 GB/T870-1986 半沉头铆钉Oval countersunk head rivets 156 GB/T 871-1986 扁圆头铆钉Flat round head rivets 157 GB/T 872-1986 扁平头铆钉Thin head rivets 158 GB/T 873-1986 扁圆头半空心铆钉Oval head semi-tubular rivets 159 GB/T 874-1986 120°沉头半空心铆钉120 degree countersunk head semi-tubular rivets 160 GB/T 875-1986 偏平头半空心铆钉Thin head semi-tubular rivet161 GB/T 876-1986 空心铆钉Tubular rivets 162 GB/T877-1986 开尾圆锥销Taper pins with split 163 GB/T 878-1986 螺纹圆柱销Parallel pins with external thread 164 GB/T 879-1986 弹性圆柱销Spring-type straight pins—Slotted 165 GB/T 880-1986 带孔销Pins with split pin hole 166 GB/T 881-1986 螺尾锥销T aper pins with external thread 167 GB/T 882-1986 销轴Clevis pins with head 168 GB/T883-1986 锥销锁紧挡圈Lock rings with cone pin 169 GB/T 884-1986 螺钉锁紧挡圈Lock ring with screw 170 GB/T 885-1986 带锁圈的螺钉锁紧挡圈Lock rings with screw and circlip 171 GB/T 886-1986 轴肩挡圈Rings for shoulder 172 GB/T 889-1986 1 型非金属嵌件六角锁紧螺母Prevailing torque type hexagon nuts (with non-metallic insert),style 1 173 GB/T 891-1986 螺钉紧固轴端挡圈Lock rings at the end of shaft with screw 174 GB/T 892-1986 螺栓紧固轴端挡圈Lock rings at the end of shaft with bolt 175 GB/T 893.1-1986 孔用弹性挡圈--A型Circlips for holes--Type A 176 GB/T 893.2-1986 孔用弹性挡圈--B型Circlips for hole--Type B 177 GB/T 894.1-1986 轴用弹性挡圈--A型Circlips forshaft--Type A 178 GB/T 894.2-1986 轴用弹性挡圈--B型Circlips for shaft--Type B 179 GB/T 895.1-1986 孔用钢丝挡圈Roundwire snap rings for hole 180 GB/T 895.2-1986 轴用钢丝挡圈Roundwire snap rings for shaft 181 GB/T 896-1986 开口挡圈"E" rings 182 GB/T 897-1988 双头螺柱bm=1d Double end studs--bm=1d 183 GB/T 898-1988 双头螺柱bm=1.25d Double end studs bm=1.25d 184 GB/T 899-1988 双头螺柱bm=1.5d Double end studs bm=1.5d 185 GB/T 900-1988 双头螺柱bm=2d Double end studs bm=2d 186 GB/T 901-1988 等长双头螺柱B级Double end studs (clamping type)--Product grade B 187GB/T 902.1-1989 手工焊用焊接螺柱W eld studs for manual welding 188 GB/T 902.2-1989 机动弧焊用焊接螺柱Weld studs for arc welding 189 GB/T 902.3-1989 储能焊用焊接螺柱W eld studs for capacitor discharge welding 190 GB/T 921-1986 钢丝锁圈Round wire circlips 191 GB/T 922-1986 木螺钉技术条件Specifications for wood screws 192 GB/T 923-1988 盖形螺母Acorn nuts 193 GB/T 925-1988 轻型六角自锁螺母Self-locking nuts,hexagon light 194 GB/T 927-1988 球面六角自锁螺母Self-locking nuts,hexagon sphere 195 GB/T 929-1988 单耳托板自锁螺母Self-locking nuts,singlelug, anchor 196GB/T 930-1988 双耳托板自锁螺母Self-locking nuts,twolug, anchor 197 GB/T 931-1988 角形托板自锁螺母Self-locking nuts,angle, anchor 198 GB/T 932-1988 气密单耳托板自锁螺母Self-locking nuts,singlelug, anchor, sealing, 199 GB/T 933-1988 气密双耳托板自锁螺母Self-locking nuts,twolug, anchor, sealing 200 GB/T 937-1988 成组游动托板自锁螺母Self-locking nuts, anchor, floating,Gang channel2005-11-16 22:33 315508161行业标准规范中英文对照系列之通用零部件(三) 201 GB/T 938-1988 游动自锁螺母Self-locking nuts, floating 202 GB/T 939-1988 单耳托板自锁螺母保护罩Boots forself-locking nuts, singlelug, anchor 203 GB/T 940-1988 双耳托板自锁螺母保护罩Boots for self-locking nuts,twolug, anchor 204 GB/T 941-1988 角形托板自锁螺母保护罩Boots for self-locking nuts,angle, anchor 205 GB/T 943-1988 自锁螺母技术条件Procurement specification for self-locking nuts 206 GB/T 945-1976 十字槽球面中柱头螺钉Screws,cross recessed,thin raised cheese head 207 GB/T 946-1988 开槽球面圆柱头轴位螺钉Slotted raised cheese head with shoulder 208 GB/T 947-1988 开槽球面大圆柱头螺钉Slotted large raised cheese head screws 209 GB/T 948-1988 开槽沉头不脱出螺钉Slotted countersunk head screws with waisted shank 210 GB/T 949-1988 开槽半沉头不脱出螺钉Slotted raised countersunk head screws with waisted shank211 GB/T 950-1986 十字槽圆头木螺钉Cross recessed round head wood screws 212 GB/T 951-1986 十字槽沉头木螺钉Cross recessed countersunk head wood screws 213 GB/T 952-1986 十字槽半沉头木螺钉Cross recessed raised countersunk head wood screws 214 GB/T 953-1988 等长双头螺柱C 级Double end studs (clamping type)--Product grade C 215 GB/T 954-1986 120°沉头铆钉120°degree countersunk head rivets 216 GB/T 955-1987 波形弹性垫圈W ave spring washers 217 GB/T 956.1-1987 锥形锁紧垫圈Countersunk external toothed lock washers 218 GB/T 956.2-1987 锥形锯齿锁紧垫圈Countersunk serrated external toothed lock washers 219 GB/T 959.1-1986 挡圈技术条件--弹性挡圈Specifications for ring—Circlips 220 GB/T 959.2-1986 挡圈技术条件--钢丝挡圈Specifications for ring—Round wire snap rings 221 GB/T 959.3-1986 挡圈技术条件--切制挡圈Specifications for ring—Cutting rings 222 GB/T 960-1986 夹紧挡圈Grip rings 223 GB/T 961-1988 单耳托板自锁螺母垫片Spacers for self-locking nuts,singlelug, anchor 224 GB/T 962-1988 双耳托板自锁螺母垫片Spacers for self-locking nuts,twolug, anchor 225 GB/T 963-1988 角形托板自锁螺母垫片Spacers for self-locking nuts,angle, anchor 226 GB/T 973-1976 十字槽扁圆头螺钉Screws,cross recessed,oval head 227 GB/T 974-1976 十字槽120°半沉头螺钉Screws,cross。

家具五金英语词汇AAluminum 铝BBall bearing slide脚轮滑道Bolt pin 螺栓插销Bolts and nuts for furniture 家具用螺钉/螺帽Brass 铜CCarcase 框架，架子Castor 小脚轮Ceiling 天花板Central hinges 中央铰链Chrome 铬Complete range of drawer slide 各种类型的抽屉滑道Component 零配件，元件Concealed hinge 内藏铰链Cupboard-lock 拒门锁DDecorative trims for furniture 家具金边饰条Door & window 门窗Drawer-lock 抽屉锁Drawer runner 抽屉滑槽EEquipment for surface treatment 表面处理工具3/4 extension slide 部分开式滑道FFaucet 水龙头Fixture 固定装置Full extension slide 全开式滑道Furniture fittings 家具五金Furniture hardware家具五金Furniture parts 家具零配件Furniture structural parts 家具结构零件GGas lift chassis 气压棒底盘Glass door hinge 玻璃门铰链HHeavy duty slide 承重式滑道Hook lock 钩锁KKeyboard slide 键盘板滑道LLarge head type 大头型Locating dowel 定位榫钉Lock rail 安锁冒头MMagnetic catch 磁性拉手Magnetic-lock 磁锁magnetic push latch磁性撞锁Marquetry work镶嵌装饰品Material 原材料Metal fittings 金属配件Matal handle 金属拉手Mold模具OOffice chair central tube accessories 办公椅中管配件Office chair hardware accessories 办公椅五金配件Out set 外盖型套轮PPanel veneer 板料Plastic 塑料Plastic bolt and threaded axis 塑料螺帽及牙轴Pocket door slide 柜门滑道Prevent falling off due to turning防止旋转脱落SSecret-hinge 暗铰Semifinished furniture product andaccessories 家具半成品及配件Semifinished product for interior fittings装潢用半成品Simple connecting fittings 简单五金配件Single item 单项产品Sliding door roller series 推拉门用轮系列Straight-lock 企口锁Surface gluing 板面上胶VVeneer trimming 薄片整修Vertical upright 直挂格WWood-button 木纽Wood components 木制配件Wooden bar 车件Wooden cork 木塞Wooden curtain rod and ring 木制窗帘杆及吊环Woodscrew 木螺钉Wreathed hand-rail 扭弯扶手。