下载文档原格式
Air Injection Systems with Fleck 2510 and 2510SXT Installation & Start-Up GuideThank you for purchasing an Oceanic Water System! With proper installation and a little routine maintenance your system will be providing iron free water for many years. Please review this start-up guide entirely before beginning to install your system and follow the steps outlined for best results.MEDIA CONTAINS DUST. USE PAPER MASK AND VENTILATE TO AVOID BREATHING DUST.7623 Fulton Ave, North Hollywood CA 91605For assistance call: 1-661 - 575 -0033Email us: **********************More information online: Packing List by ModelEach system comes with the following:1 Fleck 2510-SXT Backwash Control Valve with Pipe connector kit (either 1”or 3⁄4”)* 1 Fleck 2510-SXT Bypass valve 1 filter tank with distributor tube installed and media pre-filledAir Injection 2510-SXT Installation & Startup GuideThe Air Injection AIO Filter, when properly applied, is an efficient and cost-effective system for the removal of iron and HydrogenSulfide. The AIO control valve maintains a compressed“air pocket” in the top of the tank while the system isin service. As the water passes thru the air pocket, ironand Iron are oxidized. Additionally, dissolved oxygen isadded to the water. The Air Injection AIO filter mediabed then removes the iron and hydrogen sulfide fromthe water.A daily backwash will remove accumulated iron andreplenish the filter media bed. The regenerationprocess also adds a fresh air pocket to the system.Iron Air Injection 2510-SXT Installation & Startup GuidePre-Installation1.If you are going to be turning off the water to the house and you have an electric water heater,shut off the power to the water heater before beginning installation in case water heater isaccidentally drained.2.Pick a suitable location for your filter sy stem on a dry level spot where it won’t be exposed tofreezing temperatures. A minimum of 20 PSI is required. Maximum pressure is 90 PSI.3.Get all of your plumbing parts together before beginning installation. Installation typically takes3 to 5 hours. However, after installation the 2510 SXT Air Injection Filter must be allowed to runthrough a complete backwash and rinse cycle.4.After the system is installed and running, your water may be discolored, or full of sediment orrust, particularly if this is older or corroded piping. Typically, this clears up over a day or two. Assembly and Installation Instructions1.The 2510 SXT Air Injection filter is installed after the pressure tank. If you are also installing awater softener, install the softener after the 2510 SXT Air Injection filter.2.Make sure to follow to connect the in pipe to the Fleck 2510 SXT inlet and the outlet to theoutlet (see Fig 2). As you face the Fleck 2510 SXT control from the front, the water enters on the right and exits on the left. From the back (see Fig 2) the water enters on the left. The inlet andoutlet are attached to the bypass valve which is marked with arrows as well.3.Make sure there is a working gate or ball valve before the Fleck 2510 SXT AIO filter and also oneafter. Pressure gauges are optional and perhaps not necessary but a hose bib (which is a faucet that you can attach a garden hose to) is strongly recommended after the 2510 SXT AIO filterbefore the second ball valve. This makes it easy to rinse your new 2510 SXT AIO filter on start-up and gives you a place to test the water before it enters your household plumbing.4.If you will be using copper piping, do not sweat the copper pipe directly on to the Fleck 2510 SXTcontrol valve. Avoid heating up the Fleck 2510 SXT control valve plastic with the torch.5.You do not need unions to install your Fleck 2510 SXT control. If you need to remove it, the Fleck2510 SXT has quick-release couplings that make it easy to put the 2510 SXT AIO filter on by-pass and remove the filter system from the piping.6.The drain line tubing (not supplied) is connected to a drain from the drain outlet using flexible1⁄2” ID tubing. Note that the drain can run up above the Fleck 2510 SXT control and into a drain, it does not have to drain down, as the filter backwashes under line pressure from your wellpump.7.7. Ensure the brine line check valve with screen is installed on the brine valve (See Fig. 2) This isthe AIR DRAW point of entry.Air Injection 2510-SXT Installation & Startup GuideFig 2 - AIO 2510 SXT Control Valve, Back ViewSystem Limitations• •Chlorine or other strong oxidizers will damage the filter media bed of these systems and should never be used.The AIO Filter utilizes air, oxidation and filtration for the removal of Iron and Iron. This process will leave some air or effervescence in the water. The effervescence may give the water a milky appearance and is simply excess air in the water. While a certain amount of effervescence will always be present, it may be most noticeable during the first 30 days.Air Injection 2510-SXT Installation & Startup GuideBypass AssemblyThe system must be backwashed once upon startup. First, put the system into service mode. Normally the system ships in the bypass position. Once the system is properly plumbed in, make sure to turn both of the bypass valve knobs 90 degrees into service mode. Regeneration Cycle (59 minutes)1. Backwash (14 minutes) During this cycle, the water carrying the iron runs to the drain. Untreated water is available during regeneration.2. Air Recharge (40 minutes) during this cycle, the unit empties water to the drain and is recharged with air. The sound of air being recharged will be heard. Air bubbles should go down to the drain before proceeding to the next step. Adjust cycle time if necessary.3. Rapid Rinse (5 minutes) During this cycle, water enters the tank, compressing the air into a pocket at the top of the tank.4. Brine Refill (Off)5. Unit Returns to the In-Service PositionThe frequency and time of regeneration can be changed due to the following reasons.• In conditions of high-water usage and/or high levels of iron, the unit may need to regenerate more frequently than once every three days. The unit can be set for daily regeneration or to regenerate every two days. DO NOT set the regeneration frequency for a longer period than 3 days, as the filter medium can become fouled with iron, rendering the unit ineffective.For initial programming enter master programming by setting the clock to 12:01 pm. To set the time of day press and hold the up OR down arrow until the service icon is replaced with the programming icon. Use the up and down arrows to set the time of day (PM is indicated in theupper right corner of the screen). Hold the arrow button to advance quickly through the time. Once the time is set, press the extra cycle button to save the setting. Once the parameter display is gone, press and hold the up AND down arrow buttons together for 5-10 seconds until the programming icon appears and [DF] is shown in the parameter code. Once each setting has been entered, use the extra cycle button to advance to the next setting. Please Note: Most of these settings will be left alone.Depending on your system some settings may not be shown, and some settings may be different than shown here. Do not change any settings unless specifically instructed to do sodisplay should then show the service icon, with the data display flashing between the current time of day and days remaining until the next backwash. Once it reaches 0 the system will queue a backwash for the set time. A flashing service icon indicates that a backwash is queued. A manual backwash can be queued by pressing the extra cycle button. An immediate backwash can be initiated by holding the extra cycle button for about 5 seconds. The service icon indicates that the system is "In Service" and functioning correctly, it does NOT mean that the system needs service.After initial setup the master programming should not need to be used again unless a system reset is performed. Even in the event of a power outage all settings are retained. If your water use or water quality changes you canIf your controller is showing odd behavior such as erratic display, no display, or showing an error code, the first step is to try and reset it. Start with the soft reset, and if that does not solve the problem move on to the masterSoft Reset Hold Extra Cycle andDown buttons for25 secondsThis will reset all parameters to the system default values, but leaves thedays since the last backwash intact. This is a good place to start if you feelyou may have changed a default setting. After resetting proceed throughthe master programming section.Hard Reset Hold Extra Cyclebutton whileplugging the unit inThis will reset all parameters in the system. This is typically reserved forerratic behavior that a soft reset does not resolve. After resetting proceedthrough the master programming section.SXT Controller ResetsPlumbing GuidelinesBefore you continue Many homeowners install their own water systems with basic plumbing skills; if you are not comfortable with projects like this, please hire a professional plumber. Make sure to check local plumbing codes and follow any codes that apply. These instructions offer basic plumbing tips and cannot cover every situation. They are intended as a supplement and should not replace local plumbing codes or actual plumbing experience.Drain Line ConnectionPlease note: Drain water comes out under line pressure, so it can be run vertically to connect to an overhead drain pipe.Never make a direct connection into a waste water drain. A physical air gap of at least 3 inches (76 mm) between the end of the drain line and the wastewater level in the drain pipe should be used to avoid contamination of the line. An additional gap of 3/4 inch (19 mm) between the drain pipe and drain line is recommended to prevent anyproblems in the case of a pipe overflow. Using a simple P-trapas shown is ideal as well, but a stand pipe with a diameter of atleast 1.5 inches (38 mm) is adequate. As the water coming outis under pressure, make sure to secure the drain line so that itdoes not move and create a mess.Do not tie multiple systems into a single drain line.If hooking up multiple systems, each system needs a separate,independent drain line to ensure proper operation and preventdamage. Systems can all be run to the samestandpipe/sump/outside drain, but the drain line from each system needs to be separate.Do not use additional fittings on the drain line.Avoid installing any additional fittings (check valves, ball/gate valves, etc.) as this can prevent proper backwash and cause premature system failure.Do not overtighten the screws.The bypass valve will have some up and down movement, this is normal. The clips simply hold the connection fittings together and the screws only need tightened enough to keep the clips inplace. Further tightening will not stop leaks and tightening too much can damage the system, which will not be covered under warranty.Verify flow direction.Untreated water will enter the system on the side marked with an arrow pointing toward the front of the control head (on both the bypass valve and the control head itself). The inlet side will have a check valve and water will flow through it into the tank, the side shown in image will be facing you. (some models will have an arrow on the checkvalve itself, and the arrow should point toward the head).Treated water will exit the system on the side marked with anarrow pointing away from the front of the control head (on boththe bypass valve and the control head itself).Correct inlet/outlet connections are vital.Improper flow direction will prevent proper operation and candamage your system and your plumbing. The direction of flowcannot be changed. Turning the bypass upside down will notchange the direction of the water flow.It is recommended to keep the bypass in the service position when making plumbing connections and turn it to bypass when first turning the water back on. shows the bypass position. In bypass position the handles will be turned 90-degrees and be perpendicular to the inlet and outlet fittings.When soldering, do not solder directly to the included connection or close to the control head. First solder a short (min 3-inch [7.6-cm]) piece of copper pipe onto the adapters, away from the valve, before connecting the adapter to the bypass or yoke fitting.For threaded connections, do NOT tighten the adapters into fittings while they are connected to the control head. Disconnect the bypass or yoke fitting, and connect the adapter using a high-quality thread sealant (pipe joint compound or Teflon/PTFE tape), and replace.When installed the bypass valve can move up and down, this is normal.。
odis使用技巧
以下是ODIS的一些使用技巧：
1. 连接汽车和诊断设备：将ODIS诊断设备通过OBD II接口连接到待诊断的汽车上，确保连接稳固以保证数据的传输正常。
2. 软件版本与零件号识别：在大众奥迪的Flash文件库里，部分刷新包无零件号尾字母，这时需要通过软件版本号来确定零件号。
例如，软件版本120可能对应零件号4F0910793。
3. 刷新与编码：在进行软件刷新时，需要按照屏幕提示进行，包括删除OBD故障码等步骤。
刷新成功后，要检查刷新后的报告，确认更改后的零件号信息。
注意，在刷新完之后，一定要编回原始编码，否则可能会出现问题。
4. 导入导出数据：在基本信息如商品信息中，可以通过鼠标右键选择“转成excel”将数据导出。
导入基本信息时，需要先创建模板，然后按照不同的页签填写不同的信息并保存。
注意模板中的字段不能修改，否则会出现导入失败的情况。
5. 学习与实践：对于ODIS的使用技巧，只有通过实践才能真正掌握。
因此，建议多进行实际操作，以便更好地理解和运用这些技巧。
以上技巧仅供参考，实际使用时请确保遵循相关的安全规范，并根据具体情况灵活调整。
如有需要，建议咨询相关技术人员获取专业指导。
【ODIS专题】ODIS在线功能操作篇之在线软件刷新
四.ODIS在线功能操作篇
4.3在线软件刷新（建议点击放大观看）
1)进入ODIS诊断软件，点击刷新(红框内)按钮。
2)看清要求后点击继续(红框内)按钮。
3)点击确定(红框内) 。
4)选择车辆信息(红框内)。
5)点击取消(红框内) 。
6)点击无任务(红框内)。
7)请等待。
8)选择匹配软件(红框1内)后，选择进行检测(红框2内)。
9)选择-2-(红框内)。
10)输入措施代码(红框内)，措施代码会在刷新行动之前通知。
11)请等待。
12)选择完成/继续(红框内)。
13)输入GEKO用户名/密码(红框内)。
14)请等待。
15)点击完成继续(红框内)。
16)请核对零件号和软件版本后，点击是(红框内)。
17)严格按照提示操作，不可切断网络/不可中断车辆和诊断仪连接/不可关闭诊断仪
18)点击完成/继续(红框内)。
19)请等待。
20)点击完成/继续(红框内)。
21)刷新成功。
Inms综合网管系统安装使用说明书一、inms综合系统的安装 (3)1)系统需求和安装指南 (3)1.1. 系统需求 (3)1.2. 安装指南 (3)1.3. 安装前的准备工作 (4)2)开始安装 (4)2.1. 安装BDE(Borland Database Engine)数据库引擎 (4)2.2. 安装inms客户端程序 (4)2.3. 设置inms环境变量 (6)2.4. 配置inms ODBC数据源 (8)二、inms综合系统的使用 (12)1.调度监控模块的使用说明 (12)1.1打开调度监控系统 (13)1.2查看当前告警 (15)1.3操作 (17)2.对象维护模块的使用说明 (24)2.1启动对象维护程序： (24)2.2添加删除对象： (25)2.3添加对象的应用信息： (28)2.4配置模拟量日志： (30)2.5配置告警自动推图： (30)2.6制作告警语音提示： (31)3.矢量图形和画面管理的使用说明 (34)3.1图形编辑器： (34)3.2图形管理器： (40)4.图元编辑和图元管理模块的使用说明 (41)4.1图元编辑器： (41)4.2图元管理器： (45)5.FEP转换模块的使用说明 (46)5.1 程序界面 (46)5.1.1 菜单 (47)5.1.2 工具栏 (47)5.1.2.1 标准工具栏 (47)5.1.2.2 默认值工具栏 (47)5.1.3 客户区域 (47)5.2 Fep转换工具操作说明 (48)5.2.1 用户登录 (48)5.2.2 输出文件 (48)5.2.3数据显示操作 (48)5.2.3.1 显示数据表 (48)5.2.3.2 刷新 (49)5.2.3.3 定位对象树 (49)5.2.3.4完全显示模式 (49)5.2.3.5数据名称文本显示 (49)5.2.3.6 便利编辑模式 (49)5.2.3.7 排序操作 (49)5.3 数据编辑操作 (49)5.3.1 添加数据 (49)5.3.2 添加对象下级数据 (50)5.3.3 复制对象下级数据 (50)5.3.4 修改数据 (51)5.3.5 删除数据 (51)5.3.6 取消删除 (51)5.3.7 保存数据 (51)6.系统配置模块的使用说明 (51)7.数据备份模块的使用说明 (56)7.程序管理模块的使用说明 (59)7.1概述 (59)7.2安装 (59)7.3数据制作 (60)7.4用户操作 (60)7.5常见问题解答 (60)8.TCP代理模块的使用说明 (61)9.网管服务模块的使用说明 (61)10.语音告警的设置说明 (63)一、inms综合系统的安装1)系统需求和安装指南1.1.系统需求安装inms综合网管系统客户端应用程序需要以下硬件配置：●Pentium 166以上CPU●64M以上内存，1M以上显存●硬盘剩余空间大于40M●CDROM驱动器运行inms综合网管客户端程序，需要以下软件环境：●操作系统：Microsoft Windows 95，Windows 98，Windows NT4.0，Windows 2000，Windows2003●Internet Explore 4.01或者更高版本●Microsoft SQL Server 7.0 ODBC数据源驱动程序●Microsoft Excel 97或者更高版本为了得到最佳显示效果，建议显示器分辨率设置为1024 * 768 大字体方式1.2.安装指南inms综合网管系统有四种安装方式：网管服务器、网管工作站、普通工作站、W AN浏览器。
Stratus ftServer 2510 4410 6210系统安装与配置A、安装前的场地准备事项机柜—ftServer 容错服务器有机架式(RackMounted) 和塔式(Pedestal) 两种，如果用户购买的是机架式服务器，那么需要事先准备好一个机柜。
这个机柜必须19 英寸宽，并符合EIA 310-D 标准。
机柜通常条件是19 英寸宽、40 英寸深、前架与前门的距离为3 英寸以上，后架与后门的距离为6 英寸以上，前后架的间距为24.5 至30 英寸之间，机柜内有良好的空气循环条件，通常柜顶安装有排风风扇，对机柜高度没有要求，但机柜中至少有4U 以上的空间供ftServer 安装。
机柜后部应事先安装好两路PDU( 电源接线板)。
显示器、键盘鼠标—如果用户没有从Stratus 购买显示器或键盘鼠标，应事先准备好这些外部设备。
显示器必须有15 针的D-sub 接头；键盘和鼠标都是USB 接口；电源—ftServer 服务器需要使用两路电源；为保证服务器的安全运行，建议至少其中的一路使用UPS 输出的电源；整个ftServer2500 、4400、6200 服务器的运行功率大约在1000 瓦至1500 瓦之间，输入电源要求为200-240VAC，50-60Hz。
场地—容错服务器通常被用于关键业务的处理，一般不会定期关机，所以其运行场地必须保持干净整洁(符合ISO14644-1 class 8 标准)，并具有良好的光线，以便工作人员观察服务器上的各种指示灯；机柜前后应有一定的空间，供工作人员打开机柜门进行操作；机房的温度应保持在5℃至35℃之间，相对湿度应保持在8%至80% 之间。
网线—ftServer 服务器有4 个内置RJ45 接口的1000M 以太网端口，通常会组成两个虚拟的网卡，实现容错功能的对外联络；用户应根据自己的使用情况，需要准备好相应的网线和交换机端口。
如果用户购买了VTM 部件，该部件也有两个100M 以太网口，可供用户对服务器进行内部管理，用户也需要准备好相应的网线和交换机端口。
ODI安装及配置同步一、安装ODI使用odi_windows_x86_101340版本，windows2003 server操作系统：点击setup.bat进行安装：可与oracle database安装在同一个目录：二、配置ODI1.目标：把solaris:test:scott1:emp同步到localhost:orcl:scott2:emp（主机名：实例名：用户名：表名），两个数据库都为oracle。
2.在solaris主机的test实例下，修改scott.sql并使用@?/rdbms/admin/scott.sql创建scott1用户，该用户拥有与scott用户下同样的表。
3.在solaris主机上，给scott1用户添加系统权限：alter user scott1 identified by tiger1;grant connect,resource to scott1;grant create view to scott1;4.在localhost主机上，创建scott2用户，并给用户添加权限，以及创建表结构：create user scott2 identified by tiger2 default tablespace users;grant connect,resource to scott2;grant create database link to scott2;grant create synonym to scott2;create table scott2.emp(EMPNO NUMBER(4) not null,ENAME V ARCHAR2(10),JOB V ARCHAR2(9),MGR NUMBER(4),HIREDATE DATE,SAL NUMBER(7,2),COMM NUMBER(7,2),DEPTNO NUMBER(2));5.在solaris主机上，创建Master Repository用户，并给用户添加权限：create user snpm identified by snpm default tablespace users;grant connect, resource to snpm;6.在localhost主机上，创建Master Repository用户，并给用户添加权限：create user snpw identified by snpw default tablespace users;grant connect, resource to snpw;7.创建Master Repository“开始”—“所有程序”—“Oracle”—“Oracle Data Integrator”—“Repository Management”—“Master Repository Creation”。
Oracle Data Integrator使用文档综合组技术总结系列文档编号：生效日期：密级：版本：编制：审核：Copyright Notice Copyright© 2003 - 2008 Gillion Technologies Ltd.No part of this publication may be copied without the express writtenPermission of Gillion Technologies Ltd.修订历史Date Revision Description Author 2009-05-11 V1.0 胡巍目录1.导言 (5)1.1.编写目的 (5)1.2.工具版本 (5)1.3.参考文档 (5)2.ODI安装及使用 (5)3.ODI组成部分 (5)3.1.ODI概述 (5)3.2.ODI产品体系结构 (5)4.ODI功能简介 (6)4.1.Topology Manager功能简介 (6)4.1.1.主存储库和工作存储库的创建 (6)4.2.Designer功能简介 (10)5.创建一个新的Topology (13)5.1.创建一个新的上下文Context (13)5.2.创建一个新的Oracle数据服务器 (13)5.3.创建一个新的Sql server 2005数据服务器 (15)5.4.创建一个新的物理架构 (18)5.5.创建一个新的逻辑架构 (20)6.创建一个新的模型Model (22)7.创建一个新的Project (20)8.知识模块(Knowledge Module) (26)8.1.知识模块概述 (26)8.2.如何引入知识模块 (27)9.数据完整性控制 (28)9.1.静态控制 (28)9.2.流控制 (28)9.3.实例 (28)10.CDC(Changed Data Capture) (34)10.1.Journalizing模型组成 (34)10.2.实例 (34)1.导言1.1.编写目的本文旨在对项目开发中涉及运用Oracle Data Integrator进行各种类型数据库的数据整合，便于指导后续实施工作，也方便后续存档和管理用。
CN2510 Series快速安装手册Fou r th Edition, April 20081. OverviewMoxa开发的CN2510 Async Server是具有8、16个异步RS-232串口的单网口10M/100M自适应以太网口通讯服务器。
CN2510 Async Server能够将终端、调制解调器、打印机和其它的一些异步通信设备轻易连入网络。
CN2510使用标准的以太网10/100BaseT和10/100BASETX双绞线做为物理介质，符合TCP/IP协议和IEEE 802.3协议规范。
2. 产品包核对清单在您开始安装CN2510之前，请核对产品包中的物品是否符合下列清单：y1台CN2510 Async Servery1条交流电源线(仅于AC model提供)y1张Document and Software CD-ROMy1张快速安装手册y1个RJ-45 Loopback Testery1本产品五年保修y2个机架型支架和8个螺丝钉的便携式工具包。
y1条CBL-RJ45F9-150y1条CBL-RJ45M25-150选购配件y CBL-RJ45M9-150 y CBL-RJ45F9-150 y CBL-RJ45M25-150 y CBL-RJ45F25-150 RJ45 8-pin to DB9 Male cable, 150 cm RJ45 8-pin to DB9 Female cable, 150 cm RJ45 8-pin to DB25 Male cable, 150 cm RJ45 8-pin to DB25 Female cable, 150 cm如果您发现您收到的产品与清单不符，请与您购买产品的渠道商业务人员联系。
3. 硬件简介面板前端外观指示灯及按键颜色功能Reset回复默认值无Reset 按钮 — 持续按押Reset键5秒，放开后便会回复默认值 (Factory Default)。
