机械专业英语词汇
- 格式：docx
- 大小：41.80 KB
- 文档页数：51
General 通用法规，规范, code标准, standard暂行标准, tentative standard达到标准, come up to the standard 定标准, fix (set up) a standard标书，技术规格, specification要求, requirement满足要求, fulfill requirement细则, regulation规则, rule法律, law条款, provision总则, general provision附带条件，限制性条款, proviso 判椐, criterion (pl. criteria)约定条件, stipulation合同规定, on the stipulation that 合同, contract签订合同, sign a contract拟订合同, draw up a contract 违约, breach of contract代理人, mandatory强制性的, mandatory, restrictive 非强制性的, optional条件, condition符合, conform to (with)遵守, comply with确认, confirm证书, certificate认可, approve (v), approval (n.)接收, accept (v.), acceptance (n.), acceptable (a.)评定, qualify (v.) qualification (n.)满足, meet许可, permit拒收, reject废品, rejection鉴别, identify提交, submit to论证, demonstrate公约, convention仲裁, arbitration公证, notarization公证人, public notary 商检, commodity inspection & testing 独立检验员, independent inspector 业主代表, representative of S / V业主, owner委托人, client签署, sign要求, request监理员, supervisor, surveyor检查鉴定, survey检查, inspect, check,验证, verify目击，见证, witness禁止, prohibit建议, recommend满意的, satisfactory授权, authorize文件, document审查, review监控, monitor测定, detect逐个检验, individual inspection抽样检验, sampling inspection, cross check巡检, touring inspection, patrol inspection 评价, evaluate试验, test实验, experiment试样, specimen可跟踪性, traceability预先具有资格, prequalify 判定，评价, judge责任, responsibility, obligation, duty 折衷，兼顾, compromise官方，管理局, authority样本, sample保证, assure通知单, notification通知, notify (v.) notice (n.)会议纪要, minutes数量, quantity质量, quality质量控制, quality control(Q.C)质量保证, quality assurance(Q.A)缺陷, defect损坏, damage临界的, critical受控文件, valid document 停止点, hold point(H)交货, delivery竣工图, as-built drawing 原始记录, original record 传阅, recycle批注, comment答复, reply紧急, urgent宣读, read out直线度, straightness垂直度, perpendicular平整度, flatness同心度, concentricity 同轴度, axiality平行度, parallelism圆度, roundness平面度, planeness随机的, random不平, uneven空心, hollow同心, concentricity偏心, eccentric表面粗糙度, surface roughness 尺寸公差, dimension tolerance 允许误差, admissible error上偏差, upper deviation下偏差, lower deviation尺寸, dimension长度, length宽度, width高度, height厚度, thickness深度, depth跨度, span直径, diameter半径, radius外径, outer diameter 内径, inner diameter 口径, caliber拱度, camber挠度, deflection旁弯, lateral flexure 径向跳动, runout 端面跳动, endface runout中心线偏斜, lack of alignment 弯曲, flexure, bending斜度, slope角度, angle对角线, diagonal平行线, parallel中心线, center line斜线, oblique line切线, tangential line轮廓线, contour line原点，起点, original指标, index转速, rotary speed方向, direction指南, guide选定, choose选择, select挑选, pick炉批号, heat / plate number, heat batch 炉、批, lot or heat编制, drafting签发, sign & issue执行, performance报标, invitation for tender投标, tender, bid开标, bid opening中标, success of bid询价, inquiry标价, quotation of prices, offer 不相符, non-conformance 遗漏, omission去掉, remove更换, renew修补, repair几何形状, geometry型号, model暂时, temporarily测量, measure附件, annex, attachment 修正, amend型材, bar stock湿气, moisture发出, issue填写, fill in开工会, kick-off meeting间距, interval承包商, contractor分保商, subcontractor供货商, supplier操作错误, operate missing签证, visa敲打检查, hammering test拉伸试验, tensile test冲击韧性, impact toughness冲击功, impact work抗拉强度, tensile strength屈服强度, yield strength弯曲角, angle of bending冲击韧性试验, impact cupping test 压扁试验, squeezing test侧弯试验, side bend test背弯试验, root bend test面弯试验, face bend test纵弯试验, axial bend test硬度试验, hardness test破断延伸率, percentage of elongation of break断面收缩率, percentage seduction of area 无损检测, nondestructive test (NDT)破坏试验, destructive test外观检查, visual examination超声波探伤, ultrasonic test (UT)射线探伤, radiographic test(RT)磁粉探伤, magnetic particle test (MT)渗透探伤, penetrant test (PT)密封性试验, leak test气密试验, air tight test压力试验, pressure test水压试验, hydraulic test气压试验, pneumatic test冲水试验, fill water test宏观组织检查, macroscopic examination 微观组织检查, microcosmic examination 侵蚀, erosion底片, radiographic test film变形, distortion试运行, trial operation永久变形, permanent deformation凸起, camber 凸出, protrusion凹进, concave超出, protrude beyond 清除, decontaminate失败，故障, failure断裂, fracture塌陷，凹陷, collapse中断, discontinuity裂缝, crack发裂, flaw龟裂, fissure毛细裂纹, capillary crack 起始裂纹, incipient crack 断层裂纹, fault fissure 积水, stagnant water船舱, cabinProcessing 工艺加工, processing, working工艺学, technology工艺技术, technique工艺的, technologic工位, station, position工序, procedure, operation工步, step车间, shop, workshop工厂, mill, factory, manufacturer 工地、现场, site外场, yard, field侧面, side断面, section 结构, structure, construction构件,部件, member, component零件, part, element机构, mechanism装置, device机件, machinery机械零件, mechanical element基准, datum水平基准线, horizontal reference line 精度, accuracy余量, allowance组件, assemble分装件, subassemble包装, package外协件, cooperation外购件, purchase part备件, spare part裸装件, nudes散装件, odd lot, odds & ends拆包, unpackaging工件, workpiece装箱单, packing list焊接, Welding对接焊, butt welding角焊, fillet welding搭接焊, lap welding船形焊, fillet welding in down hand 塞焊, plug welding平焊, down hand welding横焊, horizontal position welding 立焊, vertical position welding仰焊, overhead position welding全位置焊, all position welding平角焊, horizontal fillet welding仰角焊, fillet welding in the overhead衬垫焊, welding with backing单面焊双面成形, one-side welding with back formation定位焊, tack welding堆焊, surfacing返修焊, rewelding补焊, repair welding隔离层堆焊, buttering手工焊, manual welding自动焊, automatic welding焊条电弧焊, shielded metal arc welding(SMAW)埋弧焊, submerged arc welding(SAW)气保焊, gas shielded arc welding氩弧焊, argon arc welding钨极氩弧焊, argon tungsten arc welding 熔化极惰性气体保护焊, MIG钨极惰性气体保护焊, TIG活性气体保护电弧焊, metal active-gas arc welding (MAG)CO2气保焊, carbon-dioxide arc welding 药芯焊丝CO2气保焊, arcos arc process, dual shielded arc welding单面焊, welding by one side双面焊, welding by both sides单道焊, single pass welding 多道焊, multi-pass welding 单层焊, single layer welding 多层焊, multi-layer welding 连续焊, continuous welding 断续焊, intermittent welding 打底焊, backing welding盖面焊, cosmetic welding 分段退焊, backstep welding 纵缝, longitudinal seam横缝, transverse seam环缝, circumferential seam 螺旋缝, spiral seam坡口, groove坡口面, groove face坡口面角度, level angle坡口角度, groove angle坡口高度, groove depth钝边, root face钝边高度, thickness of root face 根部间隙, root gap根部半径, root radius根部锐边, root edgeI型坡口, square groove坡形板边（削薄）, tapered edge 焊缝表面, weld face焊缝背面, back of weld焊缝尺寸, size of weld焊缝厚度, throat thickness熔深, penetration焊缝成形, appearance of weld 余高, reinforcement背面余高, root reinforcement焊脚, leg焊缝腰高, theoretical throat焊根, weld root焊趾, weld toe凸形角焊缝, convex fillet weld凹形角焊缝, concave fillet weld交错断续角焊缝, staggered intermittent fillet weld并列断续角焊缝, chain intermittent fillet weld密封焊缝, seal weld熔透焊缝, penetration bead保留垫板, permanent临时垫板, temporary backing垫板, backing铜垫板, copper backing焊剂垫, flux backing引弧板, run-on tab end tab引出板, run-off tab end tab引弧, arc start, arc burning熄弧, arc outage, arc blowout焊接工艺评定, welding procedure qualification(WPQ)焊接工艺规程, welding procedure specification(WPS)焊接工艺参数, welding parameter 焊接电流, welding current电弧电压, arc voltage焊接速度, weld travel speed预热, preheat 后热, postheat层间温度, interpass temperature焊后热处理, post weld heat treatment 焊接环境, welding surroundings焊工考试, welder qualification test清根, root back gouged, back chipping 清渣, slag removal定位板（马〕, strong-back电弧偏吹, arc flow熔滴, droplet拼接, splice焊缝清理, weld cleaning气刨, gouge批凿, chip锤击, peening捻缝, caulking中间焊层, intermediate weld layer划线, mark off熔渣, slag焊缝穿越孔, weld access hole焊态, as-weld过热组织, overheated structure魏氏组织, Widmannst?tten structure 层状偏析, lamellar segregation熔合线, bound line热影响区, heat-affected zone (HAZ)碳当量, carbon equivalent晶间腐蚀, intercryctalline corrosion 敏化区腐蚀, weld decay焊接残余应力, welding residual stress 消除应力, stress relieving退火消除应力, stress relieving by annealing焊接残余变形, welding residual deformation角变形, angular distortion波浪变形, wave-like deformation 扭曲, twisted收缩, shrinkage反变形, backward deformation刚性固定, rigid fixing校正, straighten火焰校正, flame straightening焊接缺陷, weld defect裂纹, crack层状撕裂, lamellar tearing气孔, blowhole密集气孔, porosity虫形气孔, worm hole咬边, undercut焊瘤, overlap凹坑, pit烧穿, burn through塌陷, excessive penetration未焊透, incomplete penetration 未熔合, incomplete fusion未焊满, Incompletely filled weld 根部缺陷, root concaving电弧擦伤, arc scratch, arc strike 夹渣, slag inclusion白点, fish eye 错边, dislocation, mismatching, misalignment分层, stratification嵌条, insert飞溅, spatter机械擦伤, mechanical damage 焊缝成形差, rough weld锤痕, hammering pit麻点, pock边缘不平整, rough edge剥落, peel弧坑, crater焊道曲折, zigzag weld外形规整, smooth contour歪斜, crooked翘曲, warping焊接材料, welding consumables焊条, electrode酸性焊条, acid electrode碱性焊条, basic electrode低氢焊条, low hydrogen type electrode 焊剂, welding flux焊丝, welding wire镀铜焊丝, copper -plating welding wire 药心焊丝, flux-cored wire电弧焊机, arc welding machine弧焊电源, arc welding power source 焊条保温筒, thermostat for electrode 干燥箱, dryer地线, earth lead 地线夹头, earth clamp平台, platen滚轮架, turning roll胎架, placentas压缩空气, compressed air焊接量规, weld gauge测温笔, tempil stick打磨, grind (ground)焊钳, electrode holder砂轮机, grinder钢丝刷, wire brush砂纸, sand-paper砂布, emery cloth气焊, gas welding氧-乙炔焊, oxy-acetylene welding热喷涂, thermal spraying气割, gas cutting电弧切割, arc cutting等离子弧切割, plasma arc cutting (PAC)空气等离子弧切割, air plasma arc cutting 仿形切割, shape cutting数控切割, NC cutting碳弧气刨, carbon arc air gouging坡口切割, bevel cutting切割面质量, quality of cut face缺口, notch挂渣, adhering slag结瘤, dross周边焊, around welding电弧偏吹, arc blow 焊态, as-welded铜垫板, copper chill plate焊接熔池, weld pool焊接区, weld region送丝速度, wire feed speed反变形, backward deformation收缩变形, contraction deformation翘曲变形, deflection deformation油漆, Painting底漆, primer painting, under coating中层漆, intermediary painting面漆, finishing painting, top coating锌粉底漆硬化剂, curing agent, hardener 溶剂, solvent溶剂气化, solvent boiling稀释剂, thinner环氧富锌漆, epoxy zinc rich primer 磷化漆, Phosphorized painting沥青, asphalt表面预处理, surface pretreatment 喷砂, sand blasting喷丸, shot blasting除锈, rust removal, derusting除漆, depainting脱脂, degreasing除氧化皮, scaling喷涂, spray painting刷涂, brushing防锈, antirust辊涂, roller-painting 电镀, electroplating镀锌, galvanized腻子, putty刮腻子, puttying擦净, scouring晾干, airing嵌填, implant防滑面漆, finishing non-slip paint 清漆, varnish防锈漆, rust preventive oil脱脂漆, antirust grease防锈纸, rust preventive paper搅拌, stirring条纹状涂层, stripe coating色素, pigment沉淀, sediment无空气喷漆, airless spray相对湿度, relative air humidity湿度计, moisture gauge, psychomotor 粗躁度, profile roughness干膜厚度,湿膜厚度,膜厚仪, film thickness gauge粘度计, viscosity meter露天, open含水量, moisture content混合比例, mixing ratio风向, fan angle清洁度, cleanliness覆盖度, coverage 露点测量器, dew point calculation汽化, flash off再喷涂最小间隔, minimum recoating interval附着力试验, paint adherence test, cross-hatch test附着力, adhesion密度, density起泡, blistering气泡, bubble气孔, blowhole针孔, pin hole起皱, wrinkling, crumple凹坑, pitting流淌, running流挂, sagging起皮, peeling桔皮状, orange peeling发黑, blackening泛黄, yellowing开裂, cracking颜色和光泽不均匀, uneven colour & gloss涂层中夹灰和砂, retention of dust &sand 厚度不均匀, uneven thickness of film露底, holiday剥落, peel off脱皮, spalling刷痕, brush mark渗色, bleeding自然老化, weathering 飞漆, overspray漆渣, paint dregs油漆烧焦, burnt &charred paint褪色, discolour; fading粉状表面, powdery surface污染, contamination鳞片, lamination刮痕, scratch堆积, accumulation混浊膜, blushing烤焦, boiling粘附, sticks浪费油漆, over consumption of paint 隐蔽部位, hidden past散布, scattered残余物, residues光泽, gloss均匀地, evenly尾状漆, tailing灰尘, dust锈, rust干燥, drying油漆附着力强度值, painting adherence strength value氧化皮, oxide scale冷作, cold work配作, matching making对称制作, symmetrical排料, blank layout放样, lofting, layout 展开, development号料, layout off胀形, bulging扩口, flaring ,expanding缩口, necking拱曲, arching放边, release side卷边, curling, crimping折边, hemming, folding翻边, flanging刨边, edge planning修边, trimming拔缘, side bending矫正、校形, correction, rectification 矫直, straightening, leveling校平, flattening划线, laying out切断, cutting打样冲眼, center-punching 锯切, sawing錾削, chipping铲去, chips off压皱, corrugate锉削, filing堵孔, hole plugging出白, baring工件, work piece嵌补, inserting贴补, patching榫接, rabbet 抛光, polishing机械加工, Machining, Mechanical working 钳工加工, bench working砂纸打磨, sanding找正, centering配键, key fitting刮研, spotting-in, rescraping配研, running-in, facing-up毛刺, burr去毛刺, deburring无毛刺, out buss打磨修正, dress修磨光滑, dressed smooth滚花, knurling倒角, chamfering倒圆角, sounding, filleting倒钝锐边, breaking sharp corners，rounding sharp edges车削, turning rolls铣削, milling刨削, planning, shaping钻孔, drilling铰孔, reaming锪削, spotting镗削, boring插削, slotting拉削, (pull) broaching推削, push broaching铲削, relieving, backing-off刮削, scraping 磨削, grinding滚削, hobbing扩孔, counterboring, core drilling冲孔, punching, piercing, perforation 钻中心孔, centering模具, die, mould力矩扳手, torque wrench铆接, riveting剪断, shearing锯断, sawing粘接, glued joint, adhesive-bonding 热处理, Heat treatment表面热处理, surface heat treatment 固溶处理, solution heat treatment 稳定化处理, stabilizing treatment水韧处理, water toughening 渗碳, carburization, carburizing 渗氮, nitriding磷化, phosphating硬化,强化, hardening时效, ageing退火, annealing正火, normalizing淬火, quenching回火, tempering调质, quenching& tempering 脱碳, decarbonization过烧, burning过热, overheating冷脆, cold brittleness 热(红)脆, hot(red) shortness氢脆, hydrogen embrittlement 蓝脆, blue brittleness回火脆性, temper brittleness 偏析, segregation白点, flake, white spot软点, soft spot晶粒, grain晶界, grain boundary断口, fracture总装, general assembly零件装配, component assembly 部件装配, subassembly配合, fit安装, erection, installation拆卸, disassembly, dismantle 磨擦, friction磨损, abrasion, wear润滑, Lubrication集中润滑, central lubrication 分散润滑, separate lubrication 泄漏, leakage密封, seal填料函(箱), stuffing box填料, packing铸造, Casting冒口, riser, feeder浇口, gate, sprue粘砂, burning-on砂眼, sand hole 气眼, air pocket结瘤, heel多肉, metallic projections残缺, incompleteness冷隔, cold shut缩孔, shrinkage清砂, cleaning铸型, mold型芯, core铸件, casting锻造, Forging锻件, forge piece成形, forming辊形, roll forming冲压, stamping, pressing, punching冲裁,落料, blanking 旋压, spinning滚压, rolling拉延, drawing拉拔, drawing, draft 轧制, rolling弯形, bending弯管, pipe bending 卷园, edge coiling 切口, lancing翻孔, hole flanging 滚园, rolling circle 下料, cropping冲压件, stamping 回弹, spring-back 展宽, spreading角裂, chink飞边, flash off连皮, wad, slug凸耳, earing隆起、堆积, piling, build-up烧损, scale (heating)loss缩孔, shrinkage cavity缺肉, underfill非金属夹杂, non-metallic inclusions 折（重）叠, lap, overlap错差, mismatch粉末冶金, Powder metallurgy粉末冶金制品, powder product烧结结构零件, sintered structural part手提电脑, notepad, laptop程序, program软盘, floppy disk软件, software光盘, CD-ROM病毒, virus杀毒, kill virus数码像机, digital camera容量, capacityCrane起重机桥吊, quayside crane轮胎吊, rubber tyred gantry crane(RTG)装船机, ship loader卸船机, ship unloader堆取料机, stacker-reclaimer 前大梁, boom后大梁, girder立柱，支腿, leg海侧, seaside陆侧, landside上横梁, upper beam下横梁, sill beam连接横梁, horizontal beam梯形架, A-frame, pylon大平衡梁, upper equalizer中平衡梁, intermediate equalizer 小平衡梁, lower equalizer主动车架, driving bogie从动车架, driven bogie前拉杆, forestay后拉杆, backstay斜撑杆, diagonal bar机器房, machinery house司机室, operator's cab电器房, electrical room理货室, check's cab俯仰操纵室, boom hoist cab 小车, trolley大车, gantry托缆小车, catenary trolley 吊具, spreader上架, headblock电梯, elevator吊钩横梁, hook beam辅助结构, auxiliary structure 后置平台, rear platform倾转平台, trim / list / skew (T / L / S) platform上铰座, upper bracket下铰座, lower bracket防挂仓装置, snag load device锚定装置, anchor device顶轨装置, rail brake device防风系缆, tie down防碰撞装置, bumper轨道夹钳, rail clamp吊具调整装置, trim, list & skew device 安全钩, boom latch, safe hook电缆卷筒, cable drum, cable winder电缆拖令, festoon cable车挡, stopper避雷针, lightning rod灭火器, fire extinguisher防摇装置, anti-sway device防跳装置, anti-bouncer防松装置, slack-preventing device 起升滑轮, main hoist reel牵引滑轮, trolley travel reel俯仰滑轮, boom hoist reel出绳罩, ropes outlet hood吊耳, lifting lug铰点, hinge隔板, diaphragm腹板, web盖板, flange 纵向加筋, longitudinal fillet承轨梁, track girder, rail beam横梁, transverse beam, cross beam 伸缩梁, telescopic beam吊具导板, flipper吊具转销, spreader twistlock梯子, ladder阶梯, stop, stair平台, platform走台, footwalk, walkway扶手, hand rail栏杆, railing护栏, protection cage直梯, vertical stair斜梯, inclined stairs(ladder)踢脚板, skirting boards, foot panel 波纹板, corrugated plate花纹板, chequered plate网板, wire-mesh plate格栅板, grating plate, grid plate 折边板, edgefold plate支承板, bracket支架, support拉板, tie plate档板, baffle钩销, hook pin联接板, link plate泄水孔, drainage hole排水孔, outlet entrance排水管, draw-off tube 铭牌, name plate钢丝绳, steel wire, rope卷扬筒, drum马达, motor减速器, reducer滑轮, reel, sheave, pulley制动器, brake制动盘, brake disc制动瓦块, brake shoe制动鼓, brake drum制动带, brake belt制动杠杆, brake lever联轴节, coupling万向联轴节, universal coupling 离合器, clutch齿轮, gear内齿轮, internal gear外齿轮, external gear斜齿轮, helical gear人字齿轮, double helical gear 伞齿轮, bevel gear太阳中心齿轮, sun gear行星齿轮, planet gear蜗轮, worm gear蜗杆, worm齿条, rack轴, axle, shaft偏心轴, encentric shaft花键轴, shine shaft轴套, shaft sleeve 轴瓦, shaft bush轴承, bearing轴承座, bearing support 链轮, sprocket链条, chain车轮, wheel轮缘, wheel flange轮毂, wheel hub轮辐, wheel spoke轮胎, tyre皮带轮, blot pulley惰轮, idle wheel吊钩, lifting hook抓斗, grab, bucket弹簧, spring紧固件, fastener螺栓, bolt高强度螺栓, high strength bolt 螺母, nut防松螺母, grip nut螺钉, screw垫圈, washer弹簧垫圈, spring washer螺纹, thread铆钉, rivet钉, nail键, key销, pin开口销, split pin闩, latch 铰链, hinge钢轨, rail brake配重, counter-weight压重, ballast备件, spare parts定位块, fix block调整块, adjustment block压板, clip鱼尾板, fish plate液压系统, hydraulic system齿接触面积, teeth contact area 噪声水平, noise level润滑, lubricate润滑剂, lubricant泄漏, leakage手柄, handle柴油箱, diesel oil box电气系统, electrical system 限位开关, limit switch继电器, relay电刷, electrical brush接头, plug插座, socket, consent配电箱, distributing box控制箱, control box开关柜, switch cabinet配电盘, distributer按钮, button, knob开关, switch cabinet断路器, breaker, disconnector 熔断器, Fuse变压器, transformer整流器, rectifier接触器, contactor电缆, cable电源, power supply绝缘, insulation接地, earthing电缆槽, cable conduit电气接线箱, electrical connection box 故障估测系统及装, MMI soft ware 调试, debugging试车, commission电梯自由坠落试验, falling test硅胶, silicone纵倾, trim横倾, list扭转, skew主起升, mail hoist俯仰, boom hoist出口孔, outlet hole进口孔, inlet hole捆扎, bind & fix予紧力矩, pretightening torque温升, raising of temperature密闭箱体, hermetic box三面成型, before classing box with last plate四面成型, box closed with last plate维修行车, maintenance crane 柴油机房, diesel engine room防风系统装置, tie down device顶轨器, rail brake测量洋冲孔, punch mark for measuring 临时焊缝, temporary weld液压泵站, hydraulic pump station缓冲器, buffer, bumper大车缓冲器, bridge bumper离合器, clutch回转架, Rotary hanger直梯横档, rung双箱梁, Double box girder单箱梁, Mono-box girder涨紧装置, Tension device换绳装置, Rereeving system空调, Air conditioner加油点, Oiling point托辊, idler挡绳器, Rope stopper抗剪块, Stop dog车轮踏面, tread控制电缆, Signaling cable 光缆, Optic fiber油污表, contaminant gauge 穿钢丝, thread, reeve布线, wire接线, terminating海绑, sea fastening大梁对中, boom alignment 编码器, encoder 发运, delivering船运安全性, cargo security控制台, console操纵板, console panel防撞装置, anti-collision device防震装置, anti-vibration橡胶垫, rubber pad油箱, oil reservoir过滤器, filter软管, hose防松, anti-loose耐久性试验, endurance test达克罗处理, Dacro移动障碍, obstruction of movement of hand over the railing pipe螺旋扣, knob楔套, wire socket楔, wedge绳夹, clamp耐磨板, wire-resisting plate 航空灯, aviation light投光灯, flood light照明灯, illuminating lamp 应急灯, emergency lamp 重锤限位, hammer limit 轮压, wheel pressure定位块, location block抗剪块, anti-cut block抗磨块, anti-wear block 清扫装置, cleaning device 挡绳装置, ward off rope device 涨紧装置, tensioning device 挡圈, check ring活塞, piston油标, oil indicator卸扣, shackle双箱吊具, twin-spreader抓斗, grab bucket牵引装置, tow device换绳装置, rope changer联动装置, linkage电缆槽, cable groove扎带, bandage衰减, attenuation贴合面, faying surface临时焊缝, temporary weldRMQC, Rail Mounted Quayside Crane防风颤装置, dampen device抱箍, U-boltContainer 集装箱底架, Base frame底侧梁,底横梁, cross beam, X-member中心梁, center rail底侧梁加强板, bottom side rail reinforcement中心梁TIR加强板, centre rail TIR patch 大底横梁, large cross member小底横梁, small cross member门端底横梁, first cross member, rear end cross member 地板支撑角铁, floor support angle叉槽角钢, fork lift pocket angle叉槽底板, fork lift pocket bottom (lower) plate叉槽顶板, fork lift pocket top (upper) plate叉槽横梁, fork lift pocket side member 鹅颈槽, gooseneck tunnel鹅颈槽枕梁, bolster鹅颈槽底梁, tunnel bow鹅颈槽外伸梁, tunnel outrigger鹅颈槽侧梁, tunnel side rail鹅颈槽板, tunnel plate中底梁(45’), intermediate bottom side rail外底侧梁(45’), bottom side rail end侧部, side侧板, side panel边侧板, end side panel大侧板, main panel顶侧梁,顶板, roof panel角防护板, corner protection plate前角板, front roof gusset外顶侧梁(45'), top side rail end中上顶梁(45'), intermediate top rail upper 中下顶梁(45'), intermediate top rail lower 中角加强板(45'), intermediate reinforcement后角板, rear roof gusset前端, front end 前端板, front panel前角柱, front corner post前顶角件, front top corner casting fitting 前底角件, front bottom corner casting fitting端框, end frame前底梁, front bottom end rail前底角件, front bottom corner casting fitting前底梁加强板, front bottom rail patch 前角柱加强板, front corner post stiffener 底角加强板, bottom corner stiffener防撞槽钢, cone damage protector前底梁保护槽钢, front protection channel前TIR加强板, front TIR patch前顶梁, front top end rail前顶板, front top panel固定棒, lashing bar中内角柱(45'), intermediate post inner 中外角柱(45'), intermediate post outer 系绳环, lashing ring通风窗, ventilator后端, rear end后角柱, rear corner post后内角柱, rear corner post inner后外角柱, rear corner post outer后角柱内垫板, rear corner post inner spacer后角柱内加强板, rear corner post stiffener后下角TIR填板, rear corner TIR filler 后角柱边槽, shoring slot门楣, door header门楣加强板, door header gusset后顶板, rear top panel门槛, door sill门槛加强板, door sill gusset防撞槽钢, door burnper, rear protection channel铰链开口, rear frame cut out for hinges 后加强板, rear reinforcement后TIR加强板, rear TIR patch门页, door leaf (leaves)门横梁, door horizontal member门纵梁, door vertical member门板, door panel碰板, slam plate铰链耳, hinge lug门挡板, door keeper铰链, hinge铰链叶, hinge blade铰链销, hinge pin铰链销衬垫, hinge pin bush 门五金件, door hardware锁件, twist lock锁杆, locking rod锁头, locking cam锁座, cam keeper把手, handle把手铰链, handle hinge把手铰链销, handle hinge pin 把手固定夹, handle hub铆钉, rivet实芯铆钉, solid rivet抽芯铆钉, blind rivet开花钉, drive rivet哈克螺栓, Huck bolt六角头螺栓, hexagon head boil螺母, Nut园头螺栓, round head bolt弹簧垫圈, spring washer自攻螺钉, self tapping screw密封圈, gasket橡胶门封条, rubber gasket密封圈夹持片, gasket keeper(retainer)封胶, sealing(S/L)丁基密封胶, butyl sealant氯化密封胶, chloroprene sealant硅胶, silicon sealant地板, floor board防虫处理板, immunization plate上漆地板, urethane coated plywood floor 安全合格牌, safety approval plate综合标记牌, consolidated data plate CSC安全认可, CSC safety approval国际铁路联盟标记, UIC Mark国际公路运输海关公约认可, TIR approval plate船级社标, class emblem检验合格标, seal of inspection society 木材检疫标, immunization plate 农林徽, farming and foresting badge标志, logo铭牌, name plate箱主代码及系列号, owners code & serial No.集装箱自动识别码标志, A.E.I Tag油漆标, paint decal核对数字, check digit高度标, height mark超高标, over height mark材料表标, material list decal制造厂标, manufacturers decal国家代码, counting code超重标, super heavy decal斑马标, zebra mark, stripe mark重量标, weight decal堆码警告标, stack caution decal箱标, decal, decalcomania不干胶标, self-adhesive film decal毛重, gross weight载重, payload箱重, tare weight容积, cubic capacity样箱试验, prototype test批量试验, batch test堆码试验, stacking test起吊强度试验, lifting strength test顶角件起吊强度试验, vertical lifting test from top corner fitting底角件起吊强度试验, vertical lifting test from bottom corner fitting 叉举强度试验, lifting test from fork pocket地板强度试验, floor strength test拴固试验, restraint test端壁强度试验, side wall strength test侧壁强度试验, racking transverse test横向刚性试验, racking longitudinal test纵向刚性试验, roof strength test顶板强度试验, roof strength test水密试验, Water tightness test风雨密试验, weather proofness test漏光试验, light leak test拉伸强度试验, tensile strength test(lashing test空载, unloaded加载, loading满载, loaded支承, support偏码, offset stacking偏置, misgather冷却试验, cooling test扭曲试验, twisting test试验小车, vehicle隔热试验, heat leakage test干货箱, closen van钢干货箱, steel dry cargo container冷藏集装箱, reefer container折叠式集装箱, collapsible container , folding container绝热集装箱, insulated container内柱式集装箱, inner post type container 平台集装箱, platform container托盘集装箱, pallet container平面板式集装箱, smooth panel container 台架式集装箱, platform based container 真空集装箱, vacuum container货箱集装箱, van container拆卸式货物集装箱, demountable cargo container挂衣集装箱, hanger container保温集装箱, thermal container干散货集装箱, drt bulk container通风集装箱, ventilated container侧开门集装箱, side door container货笼, cargo cage总装, main assembly, general assembly部装, sub-assembly波形板, corrugation shape超角件, protrude over the corner fitting 未渗透, insufficient penetration工位, station夹具, jig胎架，装配架，定位装置, fixture下线, off-line堆场检验（验箱〕, yard inspection二次打砂, second shot blasting堵洞, caulking (C)堵洞后上漆, caulking & painting (C+P)歪斜, askew撞伤, damage封胶, sealing (S/L)稀释剂除油, solvent (S/V)修补, touch up (T/V)高低板（错边〕, mismatch 偏焊, welding windage点距, dot pitch箱门卡住, seized door污染物, contamination铅封, customer sealing去油脂, decreasing开卷, decoding柯定钢, corton排水, drainage曲折形, zigzag海关封板, custom catch凹凸不平的, accidented。
