船舶与海洋工程专业单词总结

船舶与海洋工程专业英语复习笔记English in Ship and Ocean EngineeringNA & OE = Naval Architecture and Ocean EngineeringNAOCE = Naval Architecture and Ocean and Civil EngineeringUnit 1 Ship TypesLecture 1 The Criterion of Translation一．船型/翻译标准College English Study本课程的地位、作用和任务●船舶与海洋工程专业英语是船舶工程和海洋工程专业的必修课，是大学“英语学习不断线”的最后一门课程。

●通过该课程的教学，要求学生完成100，000单词的阅读量。

●掌握或熟悉约1000个专业词汇。

●达到每小时300单词的英译中速度。

●具备科技论文的译/写能力。

●初步具备专业英语的对话能力。

●为毕业设计的专业阅读和以后从事科学研究及工程实际打下坚实的基础。

TranslationTo give the meaning of something said or written in another language.Criterion:Let the readers have the same feeling as the natives Fidelity\ Intelligibility\ Elegancy1．英译中目标翻译是将一种语言的意义转换成另一种语言表达出来。

翻译工作有3个标准，即不失原意（“信”），符合语言规范（“达”），以及注意修辞（“雅”）。

将科技文献翻译而言，忠于原文是第一位的，因为只有“信”，菜油可能表达出原意；但是要表达好原意，文章通顺，语言规范是不可缺少的。

另外，翻译的目标是供人阅读，因此使译文具有可读性，文采也应是科技文献翻译追求的目标。

可见，要想做好科技翻译工作，需具备被一定的专业知识，较强的外语能力和较好的汉语基础。

船舶与海洋工程专业专业英语词汇船舶与海洋工程专业专业英语词汇1、A类a faired set of lines 经过光顺的一组型线 abaft 朝向船尾absence 不存在accommodation 居住(舱室)acquisition cost 购置（获取）成本activate 作动adopt 采用aegis 保护，庇护aerostatic 空气静力学的after perpendicular (a. p. ）艉柱ahead and astern 正车和倒车 air cushion vehicle 气垫船aircraft carrier 航空母舰airfoil 气翼，翼剖面，机面，方向舵airfoil 气翼，机翼alignment chock 组装校准用垫楔(或填料)allowance 公差，余(裕)量，加工裕量，补贴 American Bureau of Shipping (美国)船级社amidships 舯amidships 在舯部amphibious 两栖的angle of attack 攻角angle plate 角钢 anticipated loads encountered at sea在海上遭遇到的预期载荷antiroll fins 减摇鳍 appendage 附体appendage 附件，附体 appendage 附体artisan 技工 assembly line 装配(流水)线athwart ships 朝 (船)横向 at-sea replenishment 海上补给axiomatic 理所当然的，公理化的2、B类back up member 焊接垫板 backing structure 垫衬结构Bar 型材，材bar keel 棒龙骨，方龙骨，矩形龙骨barge 驳船 base line 基线base, base line 基线basic design 基本设计batten 压条，板条 be in short supply 供应短缺、俏销beam 船身最大宽，横梁beam 船宽，梁bench work 钳工 bevel 折角bid 投标 bidder 投标人(者)bilge 舭，舱底bilge 舭bilge keel 舭龙骨 bilge radius 舭半径bills of material 材料(细目)单 blast 喷丸(除锈)block coefficient 方形系数block coefficient 方形系数Board of Trade (英国)贸易厅 body plan 横剖面图body section 横剖图 Bonjean curve 邦戎曲线boom 吊杆 boundary layer 边界层bow line 前体纵剖线 bow thruster 艏侧推器bow wave 艏波boyant 浮力的bracket 轴支架，支架breadth extreme 最大宽，计算宽breadth moulded 型宽breakbulk 件杂货buckle 屈曲budget 预算，作预算buffer area 缓冲区freeboard deck 干舷甲板 freight rate 运费率fresh water 淡水 frictional resistance 摩擦阻力Froude number 傅汝德数full form 丰满船形full form ship 丰满船型 fullness 丰满度funnel 烟囱galley (船舰，飞机的)厨房Gantt Chart 施工进度表 general arrangement 总布置general arrangement 总布置 Germanischer Lloyd (德国)劳埃德船级社girder 桁，梁gradient 梯度grating 格栅 Green Book (船级社)绿皮书 (登录快速远洋船)ground level building site 平地建造场 group technology 成组建造技术grouting 填缝、灌浆 guided-missile cruiser 导弹巡洋舰habitability 适居性half breadth plan 半宽图handling equipment 装卸设备 hard chine 尖舭headroom 净空高度heave 垂荡 heel 横倾heel 柱脚，踵材，底基，倾斜 hog 中拱hogging 中拱 hold 船舱hole 水流深凹处homogeneous cylinder 均质柱状体hopper barge (自动)倾卸驳 hostile sea 凶险的波浪hostile sea 汹涌波浪 hull block 船体垫块，船体支座 hull form 船形hull form 船形 HVAC (=heating, ventilating and cooling) 取暖，通风与冷却hydraulic mechanism 液压机构 hydrodynamic 水动力学的hydrofoil 水翼hydrostatic 水静力的icebreaker 破冰船icebreaker 破冰船identified as Essential Changes 标记作“必备变更项” immerse 浸入immerse 浸没impact load 冲击载荷imperial unit 英制单位impression 模槽，型腔，印痕，印象in strake 内列板 in way of…在…处inboard profile 纵剖面图 In-depth analysis 深入研究initial stability at small angle of inclination小倾角初稳性insulation 绝缘，隔离Intact stability 完整稳性Intergovernmental Maritime Consultative Organization 国际海事质询组织Intergovernmental Maritime Consultative Organization (IMCO) 国际政府间海事质询组织International Association of Classification Society (IACS) 国际船级社联合会International Convention for the Safety of Life at Sea (ICSOLAS) 海上生命安全性国际公约International Towing Tank Conference 国际船模试验水池会议intersection 交点，交叉，横断(切)intervening deck 居中甲板introduces a bill 提出一项议案 issue periodically 定期发布(公布) iterative process 选代过程jack 千斤顶 janitorial 勤杂工，房屋照管者joggle 折曲，榫接，弯合 joiner 安装工joiner 细木工(匠)joinery 细木工keel laying 开始船舶建造(原意为“铺设龙骨架”) Kips (= kilo-pounds) 千磅laborer 力工Land borne 陆基的，装在陆地的 landing craft 登陆艇large tank and sphere 大型油罐和球罐launch 发射，下水launching equipment（向水中）投放设备launching way (船舶)下水滑道 LCC(Large Crude Carrier）大型原油轮（载重10~20万吨）lead time 设计至投产、定货至交货的时间 legislation 立法length between perpendicular 两柱间长leveler 调平器，矫平机，矫直机life saving appliance 救生设备 life-cycle cost 生命周期成本lift fan 升力风扇lift offsets 量取型值Light ship weight 空船重量 lighter 港驳船likely 多半，可能line 型线liner 定期航班船liner trade 定期班轮营运业lines plan 型线图liquefied gas carrier 液化气运输船list 倾斜, 表living and utility spaces 居住与公用舱室Lloyd’s Machinery Certificate (LMC) 劳埃德(船舶)机械证书Lloyd’s Register of Shipping (英国)劳埃德船级社Lloyds Rules 劳埃德(船级社)规范LNG containment 液化天然气容器Load Line Regulation 载重线公约、规范load waterline 载重水线load waterplane 载重水线面loft floor 放样台full scale 全尺度loftman 放样工loftman 放样工longitudinal 纵向的longitudinal 纵向的，纵梁longitudinal prismatic coefficient 纵向棱形系数machinery vendor 机械(主机)卖方magnet gantry 磁力式龙门吊maiden voyage 处女航main shafting 主轴系major ship 大型船舶maneuverability 操纵性maritime 海事的，海运的，靠海的，沿海的mark out 划线，划记号marshal 调度mast 桅杆maximum beam amidships 舯最大宽member 部件merchant ship 商船metacenter 稳心metacentric height 稳心高metal plate bath 金属板电镀槽metal worker 金属工metric unit 公制单位midbody （船）中体middle line plane 中线面midship area coefficient 舯横剖面系数midship section 舯横剖面midship section coefficient 舯横剖面系数mill shape 轧钢厂型材module assembly 模块式组装mold loft floor (型线)放样间地板molded lines 型线molder 造型工mould loft 放样间moulded line 型线multihull vessel 多体船Multi-ship program 多种船型建造规划nautical mile 海里naval architect 造船师naval architecture 造船工程naval ship 军船naval architecture 造船学nearuniversal gear 准万向齿轮network flow 网络流程neutral equilibrium 中性平衡normal 法向，法向的，正交的normal force 法向力normal operating condition 常规(正常)运作工况notch 开槽，开凹口Off the shelf 成品的，畅销的，流行的off-center loading 偏移中心的装载offsets 型值offshore drilling 离岸钻井oil-rig 钻油架operational requirement 军事行动需求，运作要求orient 取向，定方位，调整orthogonal 正交的，矩形的out strake 外列板outboard profile 侧视图outfit 舾装outfitter 舾装工outfitting 舾装overall stability 总体稳性overhang 外悬overstocking 存货过剩owner’s staff 船东的雇(职)员paint priming 涂底漆Panama Canal 巴拿马运河panel line system 板材生产线系统parallel middle body 平行中体patternmaker 木模工payload 有效载荷permanent body 永久性组织机构perpendicular（船艏、艉）柱，垂直的，正交的pillar 支柱pin 钉，销pin jig 限位胎架pintle 销，枢轴pipe fitter 管装工pipe laying barge (海底) 铺管驳船piping 管路pitch 纵摇plan views 设计图planing hull 滑行船体pleasure ship 游乐用船Plimsoll line 普林索尔载重线polar-exploration craft 极地考察船Polaris (submarine) 北极星级(潜艇)port 左舷portable gate 移动式(可移动)闸门positive righting arm 扶正力臂power and lighting system 动力与照明系统preliminary design 初步设计preliminary/concept design 初步/概念设计pressure vessel 压力容器principal dimensions 主尺度prism 棱柱体prismatic coefficient 棱形系数procurement 采购，获得Program Evaluation and Review Technique 规划评估与复核法quartering sea 尾斜浪, 从船斜后方来的浪quay(横)码头，停泊所racking 倾斜，变形，船体扭转变形radiography X射线照相术，X射线探伤rake 倾角,倾斜ram pressure 速压头，冲压，全压力rectangle 矩形reenlistment 重征服役Registo Italiano Navale (意大利)船级社remedial action 补救措施reserve buoyancy 储备浮力reserve buoyancy 储备浮力residuary resistance 剩余阻力resultant 合力resultant 合力retract 收进revolving crane 旋转式(鹤)吊，转臂吊(车)Reynolds number 雷诺数rigger 索具装配工rigid side walls 刚性侧壁rise of floor 底升risk 保险对象，保险金额rivering warfare vessel 内河舰艇rivet 铆接，铆钉roll 横摇rolled angle butt (轧制)角钢焊接头roll-on/roll-off(RO-RO) 滚装rough sea 汹涌的波浪round of beam 梁拱rounded gunwale 修园的舷边rubber tile 橡皮瓦rudder post 舵柱rudder 舵rudder rate 舵率rudder stock 舵杆run 去流段Sag 中垂sagging 中垂scale 缩尺，尺度，尺scale model 缩尺船模scantling 材积sea keeping performance 耐波性能seasickness 晕船seaworthiness 适航性section 剖面，横剖面sections (铁、钢)型材，轧材self-induced 自身诱导的semi finished item 半精加工件semisubmersible drilling rig 半潜式钻井架set course 设定的航线set course 设定航线shaft bossing 轴包套shaft bracket 轴支架shear 剪切，剪力sheer aft 艉舷弧sheer forward 艏舷弧sheer drawing 剖面图sheer plane 纵剖面sheer profile 纵剖线sheer profile 纵剖图sheer(甲板)舷弧sheet metal work 钣金工，冷作工shell plating 船壳板shell 船壳板ship fitter 船舶装配工ship fitter 船体安装工ship fitter 舰船装配工ship form 船型ship Hydrodynamics 水动力学ship owner 船东shipping line 船运航线shipway (造)船台shipwright 船体装配工，造船工人shipyard 船厂shipyard 船厂shipyard schedule chart 船厂施工进度图shoring 支撑，支柱shoulder 船肩sideways 朝侧向six degrees of freedom 六自由度sizable 相当大的skirt（气垫船）围裙slamming 砰击，拍击slice 一部分，薄片sloping shipway 有坡度船台，滑道soft chine 圆舭spare part 备件specially prepared form 专门(特殊)加工的模板spectrum 谱speed-to-length ratio 速长比stability 稳性stable equilibrium 稳定平衡standard 规章starboard 右舷static equilibrium 静平衡statically determinant 静定的statistical 统计学(上)的steel marking 钢板划线steering gear 操纵装置steering gear 操纵装置，舵机stem 船艏stem contour 艏柱型线stern 艉stern frame 艉构架，艉框架stern wave 艉波stiffen 加劲，加强stiffener 肋骨strain 应变strake 船体列板stringent safety regulations 严格的安全规章structural alignment 结构校准，组合，组装strut 支柱，支撑构形subassembly (局部)分部装配subdivision 分舱sublet 转包，分包，转租submersible 潜器suction cup 吸盘Suez Canal Tonnage 苏伊士运河吨位限制summer load water line 夏季载重水线super cavitating propeller超空泡螺旋桨superintendent 监督管理人，总段长，车间主任superstructure 上层建筑supertanker 超级油轮supervision of the Society’s surveyor 船级社验船师的监造surface piercing 穿透水面的surface preparation and coating 表面加工处理与喷涂surge 纵荡surmount 顶上覆盖，越过survivability 生存力SWATCH(Small Waterplane Area Twin Hull) 小水线面双体船sway 横荡switchboard 控制台，开关板tabular freeboard 列成表格的干舷值tacker 定位搭焊工talking paper 讨论文件tangential viscous force 切向粘性力tanker 油轮tanker 油轮tantamount 等值的，相当的taper 弄细，变尖tee T形构件，三通管template 样板tensile stress 拉(张)应力The Register of Shipping of the People’s Republic of China 中国船舶检验局The Titanic 泰克尼克号(巨型邮轮)there is more shape to the shell 船壳板的形状较复杂titanic 巨大的to be craft oriented 与行业有关的，适应于行业性的to run the waterlines 绘制水线toed towards amidships 趾部朝向船舯ton gross=gross ton 长吨=1. 016公吨tonnage 吨位torque 扭矩torsio 扭转的trade 工种, 贸易trailer type transporter 拖车式载运车transfer sideways 横向移动transom (stern) 方尾transverse 横向的transverse bulkhead plating 横隔舱壁板transverse section 横剖面transverse stability 横稳性trawling 拖网trial 实船试验trim 纵倾trim 纵倾trim by the stern/bow 艉/艏倾trimaran 三体船trough 波谷tugboat 拖船tumble home(船侧)内倾Type A ship A类船U form U型U. S. Coast Guard 美国海岸警卫队ULCC(Ultra Large Crude Carrier）超级大型原油轮（载重量>40万吨）ultrasonic 超声波的\underwriter (海运)保险商undock 使船出坞upright position 正浮位置V shaped V型的ventilation and air conditioning diagram 通风与空调敷设设计图vertical prismatic coefficient 垂向棱形系数vertical prismatic coefficient 垂向棱形系数vicinity 邻近，附近villain 坏人，罪魁viscosity 粘性VLCC(Very Large Crude Carrier）巨型（原）油轮（载重量>20万吨）V-sectionV型剖面wash 下洗 ,艉流water line 水线waterborne 浮于水上的，水基的waterplane 水线面waterplane area coefficient 水线面积系数watertight integrity 水密完整性wave pattern 波型wavemaking resistance 兴波阻力weather deck 露天甲板weld inspection 焊缝检测welder 焊工weldment 焊件，焊接装配wetted surface 湿面积wing shaft 侧轴yacht 快艇yard issue 船厂开工任务发布书yaw 艏摇yaw 艏摇，摇艏。

IMO(Intergovernmental Maritime Organization)国际海事组织IMCO(Intergovernmental Maritime Consultative Organization)国际海事质询组织International Towing Tank Conference (ITTC) 国际船模试验水池会议International Association of Classification Society (IACS) 国际船级社协会ABS(American Bureau of Shipping) 美国船级社BV(Bureau Veritas) 法国船级社Lloyd's Register of shipping 英国劳埃德船级社RINA(Registo Italiano Navade) 意大利船级社Load Line Convention 载重线公约Lloyd's Rules 劳埃德规范Register （船舶）登录簿，船名录Green Book 绿皮书，19世纪英国另一船级社的船名录，现合并与劳埃德船级社，用于登录快速远洋船Supervision of the Society's surveyor 船级社验船师的监造书Merchant Shipbuilding Return 商船建造统计表BSRA 英国船舶研究协会HMS 英国皇家海军舰艇CAD(computer-aided design) 计算机辅助设计CAE(computer-aided manufacturing) 计算机辅助制造CAM(computer-aided engineering) 计算机辅助工程CAPP(computer -aided process planning) 计算机辅助施工计划制定IAGG(interactive computer graphics) 交互式计算机图像技术a faired set of lines 经过光顺处理的一套型线a stereo pair of photographs 一对立体投影相片abaft 朝向船体abandonment cost 船舶废置成本费用accommodation 居住（舱室）accommodation ladder 舷梯adjust valve 调节阀adjustable-pitch 可调螺距式admiralty 海军部advance coefficient 进速系数aerostatic 空气静力学的aft peak bulkhead 艉尖舱壁aft peak tank 艉尖舱aileron 副鳍air cushion vehicle 气垫船air diffuser 空气扩散器air intake 进气口aircraft carrier 航空母舰air-driven water pump 气动水泵airfoil 气翼，翼剖面，机面，方向舵alignment chock 组装校准用垫楔aluminum alloy structure 铝合金结构amidships 舯amphibious 两栖的anchor arm 锚臂anchor chain 锚链anchor crown 锚冠anchor fluke 锚爪anchor mouth 锚唇anchor recess锚穴anchor shackle 锚卸扣anchor stock 锚杆angle bar/plate 角钢angle of attack 攻角angled deck 斜角甲板anticipated loads encountered at sea 在波浪中遭遇到的预期载荷anti-pitching fins 减纵摇鳍antiroll fins 减摇鳍anti-rolling tank 减摇水舱appendage 附体artisan 技工assembly line 装配流水线at-sea replenishment 海上补给augment of resistance 阻力增额auxiliary systems 辅机系统auxiliary tank 调节水舱axial advance 轴向进速backing structure 垫衬结构back-up member 焊接垫板balance weight 平衡锤ball bearing 滚珠轴承ball valve 球阀ballast tank 压载水舱bar 型材bar keel 棒龙骨，方龙骨，矩形龙骨barge 驳船base line 基线basic design 基本设计batten 压条，板条beam 船宽，梁beam bracket 横梁肘板爱beam knee 横梁肘板bearing 轴承bed-plate girder 基座纵桁bending-moment curves 弯矩曲线Benoulli's law 伯努利定律berth term 停泊期bevel 折角bidder 投标人bilge 舭，舱底bilge bracket 舭肘板bilge radius 舭半径bilge sounding pipe 舭部边舱水深探管bitt 单柱系缆桩blade root 叶跟blade section 叶元剖面blast 喷丸block coefficient 方形系数blue peter 出航旗boarding deck 登艇甲板boat davit 吊艇架boat fall 吊艇索boat guy 稳艇索bobstay 首斜尾拉索body plan 横剖面图bolt 螺栓，上螺栓固定Bonjean curve 邦戎曲线boom 吊杆boss 螺旋桨轴榖bottom side girder 旁底桁bottom side tank 底边舱bottom transverse 底列板boundary layer 边界层bow line 前体纵剖线bow wave 艏波bowsprit 艏斜桅bow-thruster 艏侧推器box girder 箱桁bracket floor 框架肋板brake 制动装置brake band 制动带brake crank arm 制动曲柄brake drum 刹车卷筒brake hydraulic cylinder 制动液压缸brake hydraulic pipe 刹车液压管breadth extreme 最大宽，计算宽度breadth moulded 型宽breakbulk 件杂货breasthook 艏肘板bridge 桥楼，驾驶台bridge console stand 驾驶室集中操作台buckle 屈曲buffer spring 缓冲弹簧built-up plate section 组合型材bulb plate 球头扁钢bulbous bow 球状船艏，球鼻首bulk carrier 散货船bulk oil carrier 散装油轮bulkhead 舱壁bulwark 舷墙bulwark plate 舷墙板bulwark stay 舷墙支撑buoy tender 航标船buoyant 浮力的buoyant box 浮箱butt weld 对缝焊接butterfly screw cap 蝶形螺帽buttock 后体纵剖线by convention 按照惯例，按约定cable ship 布缆船cable winch 钢索绞车camber 梁拱cant beam 斜横梁cant frame 斜肋骨cantilever beam 悬臂梁capacity plan 舱容图capsize 倾覆capsizing moment 倾覆力臂captain 船长captured-air-bubble vehicle 束缚气泡减阻船cargo cubic 货舱舱容，载货容积cargo handling 货物装卸carriage 拖车，拖架cast steel stem post 铸钢艏柱catamaran 高速双体船，双体的cavitation 空泡cavitation number 空泡数cavitation tunnel 空泡水筒center keelson 中内龙骨centerline bulkhead 中纵舱壁centroid 型心，重心，质心，矩心chain cable stopper 制链器chart 海图charterer 租船人chief engineer 轮机长chine 舭，舷，脊chock 导览钳CIM(computer integrated manufacturing) 计算机集成组合制造circulation theory 环流理论classification society 船级社cleat 系缆扣clipper bow 飞剪型船首clutch 离合器coastal cargo 沿海客货轮cofferdam 防撞舱壁combined cast and rolled stem 混合型艏柱commercial ship 营利用船commissary spaces 补给库舱室，粮食库common carrier 通用运输船commuter 交通船compartment 舱室compass 罗经concept design 概念设计connecting tank 连接水柜constant-pitch propeller 定螺距螺旋桨constraint condition 约束条件container 集装箱containerized 集装箱化contract design 合同设计contra-rotating propellers 对转桨controllable-pitch 可控螺距式corrosion 锈蚀，腐蚀couple 力矩，力偶crane 克令吊，起重机crank 曲柄crest (of wave) 波峰crew quarters 船员居住舱criterion 判据，准则Critical Path Method 关键路径法cross-channel automobile ferries 横越海峡车客渡轮cross-sectional area 横剖面面积crow's nest 桅杆瞭望台cruiser stern 巡洋舰尾crussing range 航程cup and ball joint 球窝关节curvature 曲率curves of form 各船形曲线cushion of air 气垫damage stability 破损稳性damper 缓冲器damping 阻尼davit arm 吊臂deadweight 总载重量de-ballast 卸除压载deck line at side 甲板边线deck longitudinal 甲板纵骨deck stringer 甲板边板deck transverse 强横梁deckhouse 舱面室，甲板室deep v hull 深v型船体delivery 交船depth 船深derrick 起重机，吊杆design margin 设计余量)design spiral 设计螺旋循环方式destroyer 驱逐舰detachable shackle 散合式连接卸扣detail design 详细设计diagonal stiffener 斜置加强筋diagram 图，原理图，设计图diesel engine 柴油机dimensionless ratio 无量纲比值displacement 排水量displacement type vessel 排水型船distributed load 分布载荷division 站，划分，分隔do work 做功dock 泊靠double hook 山字钩double iteration procedure 双重迭代法double roller chock 双滚轮式导览钳double-acting steam cylinder 双向作用的蒸汽气缸down halyard 降帆索draft 吃水drag 阻力，拖拽力drainage 排水draught 吃水，草图，设计图，牵引力爱dredge 挖泥船drift 漂移，偏航drilling rig 钻架drill ship 钻井船drive shaft 驱动器轴driving gear box 传动齿轮箱driving shaft system 传动轴系dry dock 干船坞ducted propeller 导管螺旋桨dynamic supported craft 动力支撑型船舶dynamometer 测力计，功率计e.h.p 有效马力eccentric wheel 偏心轮echo-sounder 回声探深仪eddy 漩涡eddy-making resistance 漩涡阻力efficiency 供给能力，供给量electrohydraulic 电动液压的electroplater 电镀工elevations 高度，高程，船型线图的侧面图，立视图，纵剖线图，海拔empirical formula 经验公式enclosed fabrication shop 封闭式装配车间enclosed lifeboat 封闭式救生艇end open link 末端链环end shackle 末端卸扣endurance 续航力，全功率工作时间engine room frame 机舱肋骨engine room hatch end beam 机舱口端梁ensign staff 船尾旗杆entrance 进流段erection 装配，安装exhaust valve 排气阀expanded bracket 延伸肘板expansion joint 伸缩接头extrapolate 外插fair 光顺faised floor 升高肋板fan 鼓风机fatigue 疲劳feasibility study 可行性研究feathering blade 顺流变距桨叶fender 护舷ferry 渡轮，渡运航线fillet weld connection 贴角焊连接fin angle feedback set 鳍角反馈装置fine fast ship 纤细高速船fine form 瘦长船型finite element 有限元fire tube boiler 水火管锅炉fixed-pitch 固定螺距式flange 突边，法兰盘flanking rudders 侧翼舵flap-type rudder 襟翼舵flare 外飘，外张flat of keel 平板龙骨fleets of vessels 船队flexural 挠曲的floating crane 起重船floodable length curve 可进长度曲线flow of materials 物流flow pattern 流型，流线谱flush deck vessel 平甲板型船flying bridge 游艇驾驶台flying jib 艏三角帆folding batch cover 折叠式舱口盖folding retractable fin stabilizer 折叠收放式减摇鳍following edge 随边following ship 后续船foot brake 脚踏刹车fore peak 艏尖舱forged steel stem 锻钢艏柱forging 锻件，锻造forward draft mark 船首水尺forward/after perpendicular 艏/艉柱forward/after shoulder 前/后肩foundry casting 翻砂铸造frame 船肋骨，框架，桁架frame spacing 肋骨间距freeboard 干舷freeboard deck 干舷甲板freight rate 运费率fresh water loadline 淡水载重线frictional resistance 摩擦阻力Froude number 傅汝德数fuel/water supply vessel 油水供给船full form丰满船型full scale 全尺度fullness 丰满度funnel 烟囱furnishings 内装修gaff 纵帆斜桁爱gaff foresail 前桅主帆gangway 舷梯gantt chart 甘特图gasketed openings 装以密封垫的开口general arrangement 总布置general cargo ship 杂货船generatrix 母线geometrically similar form 外形相似船型girder 桁梁，桁架girder of foundation 基座纵桁governmental authorities 政府当局，管理机构gradient 梯度graving dock 槽式船坞gross ton 长吨（1.016公吨，short for GT）group technology 成组建造技术guided-missile cruiser 导弹巡洋舰gunwale 船舷上缘gunwale angle 舷边角钢gunwale rounded thick strake 舷边圆弧厚板guyline 定位索gypsy 链轮gyro-pilot steering indicator 自动操舵操纵台gyroscope 回转仪half breadth plan 半宽图half depth girder 半深纵骨half rounded flat plate 半圆扁钢hard chine 尖舭hatch beam sockets 舱口梁座hatch coaming 舱口围板hatch cover 舱口盖（板）hatch cover rack 舱口盖板隔架hatch side cantilever 舱口悬臂梁hawse pipe 锚链桶hawsehole 锚链孔heave 垂荡heel 横倾heel piece 艉柱根helicoidal 螺旋面的，螺旋状的hinge 铰链hinged stern door 艉部吊门hog 中拱hold 船舱homogeneous cylinder 均质柱状体hopper barge 倾卸驳horizontal stiffener 水平扶强材hub 桨毂，轴毂，套筒hull form 船型，船体外形hull girder stress 船体桁应力HV AC(heating ventilating and cooling) 取暖，通风与冷却hydraulic mechanism 液压机构hydrodynamic 水动力学的hydrofoil 水翼hydrostatic 水静力的icebreaker 破冰船immerse 浸水，浸没impact load 冲击载荷imperial unit 英制单位in strake 内列板inboard profile 纵剖面图incremental plasticity 增量塑性independent tank 独立舱柜initial stability at small angle of inclination 小倾角初稳性inland waterways vessel 内河船inner bottom 内底in-plane load 面内载荷intact stability 完整稳性intercostals 肋间的，加强的intersection 交点，交叉，横断（切）inventory control 存货管理iterative process 迭代过程jack 船首旗jack 千斤顶joinery 细木工keel 龙骨keel laying 开始船舶建造kenter shackle 双半式连接链环Kristen-Boeing propeller 正摆线推进器landing craft 登陆艇launch 发射，下水launch 汽艇launching equipment （向水中）投放设备leading edge 导缘，导边ledge 副梁材length overall 总长leveler 调平器，矫平机life saving appliance 救生设备lifebuoy 救生圈lifejacket 救生衣lift fan 升力风扇lift offsets 量取型值light load draft 空载吃水lightening hole 减轻孔light-ship 空船limbers board 舭部污水道顶板liner trade 定期班轮营运业lines 型线lines plan 型线图Linnean hierarchical taxonomy 林式等级式分类学liquefied gas carrier 液化气运输船liquefied natural gas carrier 液化天然气船liquefied petroleum gas carrier 液化石油气船liquid bulk cargo carrier 液体散货船liquid chemical tanker 液体化学品船living and utility spaces 居住与公用舱室load line regulations 载重线公约，规范load waterplane 载重水线面loft floor 放样台longitudinal (transverse) 纵（横）稳心高longitudinal bending 纵总弯曲longitudinal prismatic coefficient 纵向棱形系数longitudinal strength 总纵强度longitudinally framed system 纵骨架式结构luffing winch 变幅绞车machinery vendor 机械（主机）卖方magnet gantry 磁力式龙门maiden voyage 处女航main impeller 主推叶轮main shafting 主轴系major ship 大型船舶maneuverability 操纵性manhole 人孔margin plate 边板mark disk of speed adjusting 速度调整标度盘mast 桅杆mast clutch 桅座matrix 矩阵merchant ship 商船metacenter 稳心metacentric height 稳心高metal plate path 金属板电镀槽metal worker 金属工metric unit 公制单位middle line plane 中线面midship section 舯横剖面midship section coefficient 中横剖面系数ML 物资清单，物料表model tank 船模试验水池monitoring desk of main engine operation 主机操作监视台monitoring screen of screw working condition 螺旋桨运转监视屏more shape to the shell 船壳板的形状复杂mould loft 放样间multihull vessel 多体船multi-purpose carrier 多用途船multi-ship program 多种船型建造规划mushroom ventilator 蘑菇形通风桶mutually exclusive attribute 相互排它性的属性N/C 数值控制nautical mile 海里naval architecture 造船学navigation area 航区navigation deck 航海甲板near-universal gear 准万向舵机，准万向齿轮net-load curve 静载荷曲线neutral axis 中性轴，中和轴neutral equilibrium 中性平衡non-retractable fin stabilizer 不可收放式减摇鳍normal 法向的，正交的normal operating condition 常规运作状况nose cone 螺旋桨整流帽notch 开槽，开凹口oar 橹，桨oblique bitts 斜式双柱系缆桩ocean going ship 远洋船off-center loading 偏离中心的装载offsets 型值offshore drilling 离岸钻井offshore structure 离岸工程结构物oil filler 加油点oil skimmer 浮油回收船oil-rig 钻油架on-deck girder 甲板上桁架open water 敞水optimality criterion 最优性准则ore carrier 矿砂船orthogonal 矩形的orthogonal 正交的out strake 外列板outboard motor 舷外机outboard profile 侧视图outer jib 外首帆outfit 舾装outfitter 舾装工outrigger 舷外吊杆叉头overall stability 总体稳性overhang 外悬paddle 桨paddle-wheel-propelled 明轮推进的Panama Canal 巴拿马运河panting arrangement 强胸结构，抗拍击结构panting beam 强胸横梁panting stringer 抗拍击纵材parallel middle body 平行中体partial bulkhead 局部舱壁payload 有效载荷perpendicular 柱，垂直的，正交的photogrammetry 投影照相测量法pile driving barge 打桩船pillar 支柱pin jig 限位胎架pintle 销，枢轴pipe fitter 管装工pipe laying barge 铺管驳船piston 活塞pitch 螺距ipitch 纵摇plan views 设计图planning hull 滑行船体Plimsoll line 普林索尔载重线polar-exploration craft 极地考察船poop 尾楼port 左舷port call 沿途到港停靠positive righting moment 正扶正力矩power and lighting system 动力与照明系统precept 技术规则preliminary design 初步设计pressure coaming 阻力式舱口防水挡板principal dimensions 主尺度Program Evaluation and Review Technique 规划评估与复核法progressive flooding 累进进水project 探照灯propeller shaft bracket 尾轴架爱propeller type log 螺旋桨推进器测程仪PVC foamed plastic PVC泡沫塑料quadrant 舵柄quality assurance 质量保证quarter 居住区quarter pillar 舱内侧梁柱quartering sea 尾斜浪quasi-steady wave 准定长波quay 码头，停泊所quotation 报价单racking 倾斜，变形，船体扭转变形radiography X射线探伤rake 倾斜raked bow 前倾式船首raster 光栅refrigerated cargo ship 冷藏货物运输船regulating knob of fuel pressure 燃油压力调节钮reserve buoyancy 储备浮力residuary resistance 剩余阻力resultant 合力reverse frame 内底横骨Reynolds number 雷诺数right-handed propeller 右旋进桨righting arm 扶正力臂，恢复力臂rigid side walls 刚性侧壁rise of floor 底升riverine warfare vessel 内河舰艇rivet 铆接，铆钉roll 横摇roll-on/roll-off (Ro/Ro) 滚装rotary screw propeller 回转式螺旋推进器9 rounded gunwale 修圆的舷边rounded sheer strake 圆弧舷板rubber tile 橡皮瓦rudder 舵rudder bearing 舵承rudder blade 舵叶rudder control rod 操舵杆rudder gudgeon 舵钮rudder horn 挂舵臂rudder pintle 舵销rudder post 舵柱rudder spindle 舵轴rudder stock 舵杆rudder trunk 舵杆围井run 去流段sag 中垂salvage lifting vessel 救捞船scale 缩尺，尺度schedule coordination 生产规程协调schedule reviews 施工生产进度审核screen bulkhead 轻型舱壁Sea keeping performance 耐波性能sea spectra 海浪谱sea state 海况seakeeping 适航性seasickness 晕船seaworthness 适航性seaworthness 适航性section moulus 剖面模数section 剖面，横剖面self-induced 自身诱导的self-propulsion 自航semi-balanced rudder 半平衡舵semi-submersible drilling rig 半潜式钻井架shaft bossing 轴榖shaft bracket 轴支架shaft coupling 联轴节shear 剪切，剪力shear buckling 剪切性屈曲shear curve 剪力曲线sheer 舷弧sheer aft/forward 艉/艏舷弧sheer drawing 剖面图sheer plane 纵剖面sheer profile 总剖线，纵剖图shell plating 船壳板ship fitter 船舶装配工ship hydrodynamics 船舶水动力学shipway/slipway 船台shipyard 船厂shrouded screw 有套罩螺旋桨，导管螺旋桨side frame 舷边肋骨side keelson 旁内龙骨side plate 舷侧外板side stringer 甲板边板single-cylinder engine 单缸引擎sinkage 升沉six degrees of freedom 六自由度skin friction 表面摩擦力skirt （气垫船）围裙slamming 砰击sleeve 套管，套筒，套环slewing hydraulic motor 回转液压马达slice 一部分，薄片sloping shipway 有坡度船台sloping top plate of bottom side tank 底边舱斜顶板sloping bottom plate of topside tank 顶边舱斜底板soft chine 圆舭sonar 声纳spade rudder 悬挂舵spectacle frame 眼睛型骨架speed-to-length ratio 速长比sponson deck 舷伸甲板springing 颤振stability 稳性stable equilibrium 稳定平衡starboard 右舷static equilibrium 静平衡steamer 汽轮船steering gear 操纵装置，舵机stem 船艏stem contour 艏柱型线stern 船艉stern barrel 尾拖网滚筒stern counter 尾突体stern ramp 尾滑道，尾跳板爱stern transom plate 尾封板stern wave 艉波stiffen 加劲，加强stiffener 扶强材，加劲杆straddle 跨立，外包式叶片strain 应变strake 船体列板streamline 流线streamlined casing 流线型套管strength curves 强度曲线strength deck 强力甲板stress concentration 应力集中structural instability 结构不稳定性strut 支柱，支撑构型subassembly 分部装配subdivision 分舱submerged nozzle 浸没式喷口submersible 潜期suction back of a blade 桨叶片抽吸叶背Suez Canal tonnage 苏伊士运河吨位限制summer load water line 夏季载重水线superintendent 监督管理人，总段长，车间主任superstructure 上层建筑supper cavitating propeller 超空泡螺旋桨surface nozzle 水面式喷口surface piercing 穿透水面的surface preparation and coating 表面预处理与喷涂surge 纵荡sway 横荡yaw 首摇surmount 顶上覆盖，越过swage plate 压筋板swash bulkhead 止荡舱壁SWATH (Small Waterplane Area Twin Hull) 小水线面双体船tail-stabilizer anchor 尾翼式锚talking paper 讨论文件tangential 切向的，正切的tangential viscous force 切向粘性力tanker 油船tender 交通小艇timber carrier 木材运输船tugboat 拖船tee T型构件，三通管tensile stress 拉（张）应力thermal effect 热效应throttle valve 节流阀throughput 物料流量thrust 推力thruster 推力器，助推器tip of a blade 桨叶叶梢toed towards amidships 趾部朝向船舯tonnage 吨位torpedo 鱼雷torque 扭矩trailing edge 随边transom stern 方尾transverse bulkhead plating 横隔舱壁板transverse section 横剖面transverse stability 横稳性trawling 拖网trial 实船试验trim 纵倾trim by the stern/bow 艉/艏倾trimaran 三体的tripping bracket 防倾肘板trough 波谷tumble home （船侧）内倾tunnel wall effect 水桶壁面效应turnable blade 可转动式桨叶turnable shrouded screw 转动导管螺旋桨tweendeck cargo space 甲板间舱tweendedk frame 甲板间肋骨two nodded frequency 双节点频率LCC 大型原油轮ULCC 超级大型原油轮VLCC 巨型原油轮ultrasonic 超声波的underwriter （海运）保险商unsymmetrical 非对称的upright position 正浮位置vapor pocket 气化阱ventilation and air conditioning diagram 通风与空调铺设设计图Venturi section 文丘里试验段vertical prismatic coefficient 横剖面系数vertical-axis(cycloidal)propeller 直叶（摆线）推进器vessel component vender 造船部件销售商viscosity 粘性V oith-Schneider propeller 外摆线直翼式推进器vortex 梢涡v-section v型剖面wake current 伴流，尾流water jet 喷水（推进）管water plane 水线面watertight integrity 水密完整性wave pattern 波形wave suppressor 消波器，消波板wave-making resistance 兴波阻力weather deck 露天甲板web 腹板web beam 强横梁web frame 腹肋板welder 焊工wetted surface 湿表面积winch 绞车windlass 起锚机wing shaft 侧轴wing-keel 翅龙骨（游艇）working allowance 有效使用修正量worm gear 蜗轮，蜗杆yacht 快艇yard issue 船厂开工任务发布书yards 帆桁--。

干货：船舶工程专业英语词汇,超齐全干货：船舶工程专业英语词汇，超齐全一、各种舱(箱)柜 All kinds of tank1、柴油日用柜 Diesel oil daily tank2、柴油澄清舱 Diesel oil setting tank3、燃油日用柜 Fuel oil daily tank4、燃油澄清舱 Fuel oil setting tank5、滑油澄清舱 Lubricating oil setting tank6、滑油储藏舱 Lubricating oil store tank7、滑油循环舱 Lubricating oil circulating tank8、燃油溢油舱 Fuel oil overflow tank9、燃油油渣舱 Fuel oil sludge tank10、燃油深舱 Fuel oil deep tank11、滑油污油舱 Lubricating dirty oil tank12、滑油溢油舱 Lubricating oil overflow tank13、滑油油渣打舱 Lubricating oil sludge tank14、主机淡水膨胀水箱 M.E fresh water expansion tank15、付机淡水膨胀水箱 A.E fresh water expansion tank16、淡水压力柜 Fresh water pressure tank17、热水压力柜 Hot water pressure tank18、饮水压力柜 Drinking water pressure tank19、淡水舱 Fresh water tank20、饮水舱 Drinking water tank21、锅炉水舱 Boiler water tank22、分油机工作水箱 Purify operating water tank23、汽缸油日用柜 Cylinder oil daily tank24、尾管滑油重力柜 Gravity tank of tube oil25、排气水封箱 Exhaust seal water tank26、蒸馏水水舱 Distilling water tank27、污水井 Bilge well1、滑油系统 Lubricating oil piping system2、燃油系统 Fuel oil piping system3、海水系统 Sea water piping system4、缸套水系统 Cylinder cooling water piping system5、启动空气系统 Start air piping system6、控制空气系统 Control air piping system7、排气系统 Exhaust piping system8、日用供水系统 Daily water piping system9、蒸汽系统 Steam piping system10、锅炉给水和凝水系统 Feed water and condensate of boiler piping system11、燃油净油系统 Fuel oil purified piping system12、燃油输送系统 Fuel oil transport piping system机舱部分 ENGINE ROOM PART二、机舱设备 Machines and equipment in engine room1、主机 Main engine1)主机油底壳 The sump tank of M.E.2)主机飞轮 Fly wheel of M.E3)活塞 Piston2、发电机 Generator engine1)应急发电机 Emergency generator engine2)辅机 Auxiliary3、锅炉 Boiler1)组合锅炉 The composite boiler2)锅炉安全阀 The safety valve of boiler3)燃烧器 Oil burner unit4)水位表 Water level gauge5)水位控制器 Water level controller6)过量蒸气调节阀 Excess steam pressure control valve 4、舵机1)舵机间 Steering room2)舵机装置 Steering-gear3)手操舵装置 Trick wheel plant4)油缸 Oil cylinder5)反馈装置 Feedback device6)舵 Rudder舵叶 Rudder blade舵杆 Rudder stock上舵承 Rudder carrier舵销 Rudder pintle舵杆衬套 rudder stock liner舵杆轴套 Sleeve for rudder stock舵销承衬套 Bush for rudder pintle舵销轴套 Sleeve for rudder pintle上舵承底座 Rudder carrier seat舵销承座 Pintle bearing舵杆承座 Rudder stock bearing挡圈 Retaining ring舵柄 Tiller舵角 The angle of rudder5、空压机 Air compressor1)主空压机 Emergency air compressor2)应急空压机3)主空气瓶 Main air reservoir4)应急空气瓶 Emergency air reservoir5)控制空气瓶 Control air reservoir6、空气干燥器 Air dryer7、分油机 Oil purifier1)燃油分油机 Fuel oil purifier2)柴油分油机 Diesel oil purifier3)滑油分油机 Lubricate oil purifier4)排渣 Sludge discharge8、制淡装置 Fresh water generator9、焚烧炉 Incinerator10、油水分离器 Oil water separator11、生活污水处理器 Sewage treat plant12、大气冷凝器 Atmosphere condenser热水井 Cascade and inspection(hot well)滑油自清滤器 The automatic back-flash lubricating oil filter燃油单元 Fuel oil unit1)主机燃油单元 Fuel oil unit of M.E2)付机燃油单元 Fuel oil unit of A.E3)粘度计 Viscosity controller泵 Pump1)主机滑油泵 Main engine lubricating oil pump2)主机缸套水泵 Main engine cylinder cooling water pump3)主机缸套水预热泵Main engine cylinder cooling water preheating pump4)主机海水泵 Main engine sea water pump5)主机燃油供给泵 Main engine fuel oil supply pump6)主机燃油增压泵 Main engine fuel oil booster pump7)主机十字头泵 Main engine cross head pump8)付机海水泵 Generator engine sea water pump9)付机缸套水泵Generator engine cylinder cooling water pump10)锅炉给水泵 Feed water pump of boiler11)锅炉燃油泵 Fuel oil pump of boiler12)分油机供给泵 Fuel oil supply pump of purifier13)制淡海水泵 Sea water pump of fresh water generator14)压载泵 Ballast pump15)舱底消防泵 Bilge and fire pump17)油渣泵 Sludge oil pump18)柴油输送泵 Diesel oil transport pump19)燃油油输送泵 Fuel oil transport pump20)汽缸油输送泵 Cylinder oil transport pump21)淡水输送泵 Fresh water transport pump22)热水循环泵 Hot water circulating pump23)饮水日用泵 Drinking water pump舱底消防总用泵 Bilge, fire and G.S pump喷淋泵 Sprinkling pump停泊海水泵 Harbor sea water pump Notification of inspection 检查验收通知单Application 申请，申请单Inspection 检验，报验Technical discussion 技术讨论On board 在船上In the workshop 在车间On the slipway 在船台上At pier(wharf) 在码头Fair 尚好的The performance is merely fair 性能尚好Terrible 极坏的，很糟的So so 马马虎虎So far ,so good 到目前，一切顺利Worse更糟的worst最差、最糟Improvement 改进Leave no room for improvement 完美，无缺点Accept 接收Accept subject to 有条件的接收，有待于……做好之后才接收Reject 拒收Comments 意见 defect lish 消除意见清单Item 项目memorandum 备忘录manual n、手册、说明书;a.手控的，手工的drawings 图纸working drawings 施工图finished drawings 完工图approved drawings 认可图drawings for approval 送审认可图supporting technical doucuments 基础技术文件sketch 草图 draw a sketch画草图up to the standard 达到标准substandard 低于标准的crane 吊车building berth 船台slipway 船台、下水滑道dry dock 干无坞pier 突码头、突堤wharf 码头along side (船)靠码头foreman 工长，领班coordinator 调度员inspector 检查员supervisor 管理人、监督人，监造人surveyor 验船师如有进出口业务咨询，欢迎咨询进贸通。

船舶与海洋工程专业专业英语词汇1、A类a faired set of lines 经过光顺的一组型线 abaft 朝向船尾absence 不存在accommodation 居住(舱室)acquisition cost 购置（获取）成本activate 作动adopt 采用aegis 保护，庇护aerostatic 空气静力学的after perpendicular (a. p. ）艉柱ahead and astern 正车和倒车 air cushion vehicle 气垫船aircraft carrier 航空母舰airfoil 气翼，翼剖面，机面，方向舵airfoil 气翼，机翼alignment chock 组装校准用垫楔(或填料)allowance 公差，余(裕)量，加工裕量，补贴 American Bureau of Shipping (美国)船级社amidships 舯amidships 在舯部amphibious 两栖的angle of attack 攻角angle plate 角钢 anticipated loads encountered at sea在海上遭遇到的预期载荷antiroll fins 减摇鳍 appendage 附体appendage 附件，附体 appendage 附体artisan 技工 assembly line 装配(流水)线athwart ships 朝 (船)横向 at-sea replenishment 海上补给axiomatic 理所当然的，公理化的2、B类back up member 焊接垫板 backing structure 垫衬结构Bar 型材，材bar keel 棒龙骨，方龙骨，矩形龙骨barge 驳船 base line 基线base, base line 基线basic design 基本设计batten 压条，板条 be in short supply 供应短缺、俏销beam 船身最大宽，横梁beam 船宽，梁bench work 钳工 bevel 折角bid 投标 bidder 投标人(者)bilge 舭，舱底bilge 舭bilge keel 舭龙骨 bilge radius 舭半径bills of material 材料(细目)单 blast 喷丸(除锈)block coefficient 方形系数block coefficient 方形系数Board of Trade (英国)贸易厅 body plan 横剖面图body section 横剖图 Bonjean curve 邦戎曲线boom 吊杆 boundary layer 边界层bow line 前体纵剖线 bow thruster 艏侧推器bow wave 艏波boyant 浮力的bracket 轴支架，支架breadth extreme 最大宽，计算宽breadth moulded 型宽breakbulk 件杂货buckle 屈曲budget 预算，作预算buffer area 缓冲区building basin 船台 bulb plate 球头扁钢bulbous bow 球状船艏bulbous bow 球鼻艏bulk oil carrier 散装油轮bulk carrier 散装货船bulk carrier 散装货船 buoyancy 浮力buoyancy 浮力Bureau Veritas (法国)船级社burning machine 烧割机 butt weld 对缝焊接buttock 后体纵剖线by convention 按照惯例，按约定3、C类camber 梁拱capacity plan 舱容图capsize 倾覆capsizing moment 倾覆力矩captured-air-bubble vehicle 束缚气泡减阻船cargo capacity 载货量，货舱容量，舱容cargo cubic 货舱舱容，载货容积cargo handling 货物装卸 cargo owner 货主carpenter 木匠 carriage of grain cargoes 谷类货物输运机cascading of waves upon…海浪跌落于… casualty 事故，死伤，灾难catamaran 双体船categorize 分类centroid 形心，重心，质心，矩心 chine 舭，舷，脊chock 木楔 circumscribe 外接，外切circumsection 外切Coast Guard cuttle(美国）海岸警备队快艇commercial ship 营利用船commissary spaces 补给库舱室，粮食库common carrier 通用运输船compartment 舱室 concave 凹，凹的，拱conceive 设想，想象concept design 概念设计configuration 构形，配置configuration安排，构型，配置conspicuous 显著的，值得注意的containerized 集装箱化 contract design 合同设计contract design 合同设计 contracted scale 缩尺core box 型芯 corrosion 锈蚀，腐蚀couple 力矩，力偶crest (of wave) 波峰crew quarters 船员居住舱 Critical Path Method (CPM) 关键路径法cross section 横剖面 cross sectional area 横剖面面积cross-channel automobile ferries 横越海峡客车渡轮crucial element 重要因素cruiser stern 巡洋舰尾cruissing range 航程curvature 曲率curves of form 各船型曲线cushion of air 气垫4、D类damage stability 破损稳性 damp out 阻息，逐渐降低dead load 恒(静)载荷 deadweight 总载重量(吨)deballast 卸除压载(压舱)deck line at side 甲板边线deck camber 甲板梁拱deck wetness 甲板淹湿 deckhouse 舱面室，甲板室declivity 坡度，斜度 deep V hull 深V型船体deformation 变形 delivery 交船Department of Trade (英国)贸易部 deposit metallic plating 镀上金属镀层depth moulded 型深depth 船深depth 船深 design spiral 螺旋式设计destroyer 驱逐舰detail design 详细设计deviation 偏离，偏差 devious 曲折的diagram 图，原理图，设计图，流程图 dimension 尺度，元，维displacement 排水量distributed load 分布载荷division 站，划分，分隔do work 做功dock 泊靠draft 吃水draftsman 绘图员 drag 阻力Drainage 排(泄)水draught(=draft) 吃水，草图，设计图，牵引力drawing office 绘图室 dredge 挖泥船drift 飘移，偏航drilling rig 钻架 dry dock 干船坞5、E类eddy 旋涡electrohydraulic 电动液压的electroplater 电镀工 elevations 高度，高程，船型线图的侧面图、立视图，纵剖线图 enclosed fabrication shop 封闭式装配车间end on 端对准 endurance 续航力endurance 续航性 entrance 进流段 erection (船体)组装erection 装配，安装 expedient 权宜之计extrapolate 外插f. p. = forward perpendicular 艏柱fair 光顺 fair 光顺fastening 坚固件,紧固法fatigue 疲劳 feasibility study 可行性研究 fender 护舷ferry 渡轮，渡口，渡运航线ferry 轮渡(载运) fillet weld connection 贴角焊连接fine fast ship 纤细(细长)高速船 fine form 瘦长(细长)船形Flank 侧面, 侧翼, 侧攻flanking rudders 侧翼舵flare 外飘，外张flat of keel 平板龙骨fleets of vessels 船队 flexural 挠曲的float 浮动时间 floating drydock 浮船坞 flood 进水，泛滥floodable length curve 可浸长度曲线 flow pattern 流型，流线谱flow of materials 物流 flush 平贴，磨光forging 锻件，锻造 form coefficient 船形系数forming operation 成型加工forward/after perpendicular 艏/艉柱forward/after shoulder 前/后肩 foundry casting 翻砂铸造 foundryman 铸造翻砂工 frame 船肋骨，框架，桁架frame 框架 freeboard 干舷freeboard 干舷freeboard 干舷freeboard deck 干舷甲板 freight rate 运费率fresh water 淡水 frictional resistance 摩擦阻力Froude number 傅汝德数full form 丰满船形full form ship 丰满船型 fullness 丰满度funnel 烟囱galley (船舰，飞机的)厨房Gantt Chart 施工进度表 general arrangement 总布置general arrangement 总布置 Germanischer Lloyd (德国)劳埃德船级社girder 桁，梁gradient 梯度grating 格栅 Green Book (船级社)绿皮书 (登录快速远洋船)ground level building site 平地建造场 group technology 成组建造技术grouting 填缝、灌浆 guided-missile cruiser 导弹巡洋舰habitability 适居性half breadth plan 半宽图handling equipment 装卸设备 hard chine 尖舭headroom 净空高度heave 垂荡 heel 横倾heel 柱脚，踵材，底基，倾斜 hog 中拱hogging 中拱 hold 船舱hole 水流深凹处homogeneous cylinder 均质柱状体hopper barge (自动)倾卸驳 hostile sea 凶险的波浪hostile sea 汹涌波浪 hull block 船体垫块，船体支座 hull form 船形hull form 船形 HVAC (=heating, ventilating and cooling) 取暖，通风与冷却hydraulic mechanism 液压机构 hydrodynamic 水动力学的hydrofoil 水翼hydrostatic 水静力的icebreaker 破冰船icebreaker 破冰船identified as Essential Changes 标记作“必备变更项” immerse 浸入immerse 浸没impact load 冲击载荷imperial unit 英制单位impression 模槽，型腔，印痕，印象in strake 内列板 in way of…在…处inboard profile 纵剖面图 In-depth analysis 深入研究initial stability at small angle of inclination小倾角初稳性insulation 绝缘，隔离Intact stability 完整稳性Intergovernmental Maritime Consultative Organization 国际海事质询组织Intergovernmental Maritime Consultative Organization (IMCO) 国际政府间海事质询组织International Association of Classification Society (IACS) 国际船级社联合会International Convention for the Safety of Life at Sea (ICSOLAS) 海上生命安全性国际公约International Towing Tank Conference 国际船模试验水池会议intersection 交点，交叉，横断(切)intervening deck 居中甲板introduces a bill 提出一项议案 issue periodically 定期发布(公布) iterative process 选代过程jack 千斤顶 janitorial 勤杂工，房屋照管者joggle 折曲，榫接，弯合 joiner 安装工joiner 细木工(匠)joinery 细木工keel laying 开始船舶建造(原意为“铺设龙骨架”) Kips (= kilo-pounds) 千磅laborer 力工Land borne 陆基的，装在陆地的 landing craft 登陆艇large tank and sphere 大型油罐和球罐launch 发射，下水launching equipment（向水中）投放设备launching way (船舶)下水滑道 LCC(Large Crude Carrier）大型原油轮（载重10~20万吨）lead time 设计至投产、定货至交货的时间 legislation 立法length between perpendicular 两柱间长leveler 调平器，矫平机，矫直机life saving appliance 救生设备 life-cycle cost 生命周期成本lift fan 升力风扇lift offsets 量取型值Light ship weight 空船重量 lighter 港驳船likely 多半，可能line 型线liner 定期航班船liner trade 定期班轮营运业lines plan 型线图liquefied gas carrier 液化气运输船list 倾斜, 表living and utility spaces 居住与公用舱室Lloyd’s Machinery Certificate (LMC) 劳埃德(船舶)机械证书Lloyd’s Register of Shipping (英国)劳埃德船级社Lloyds Rules 劳埃德(船级社)规范LNG containment 液化天然气容器Load Line Regulation 载重线公约、规范load waterline 载重水线load waterplane 载重水线面loft floor 放样台full scale 全尺度loftman 放样工loftman 放样工longitudinal 纵向的longitudinal 纵向的，纵梁longitudinal prismatic coefficient 纵向棱形系数machinery vendor 机械(主机)卖方magnet gantry 磁力式龙门吊maiden voyage 处女航main shafting 主轴系major ship 大型船舶maneuverability 操纵性maritime 海事的，海运的，靠海的，沿海的mark out 划线，划记号marshal 调度mast 桅杆maximum beam amidships 舯最大宽member 部件merchant ship 商船metacenter 稳心metacentric height 稳心高metal plate bath 金属板电镀槽metal worker 金属工metric unit 公制单位midbody （船）中体middle line plane 中线面midship area coefficient 舯横剖面系数midship section 舯横剖面midship section coefficient 舯横剖面系数mill shape 轧钢厂型材module assembly 模块式组装mold loft floor (型线)放样间地板molded lines 型线molder 造型工mould loft 放样间moulded line 型线multihull vessel 多体船Multi-ship program 多种船型建造规划nautical mile 海里naval architect 造船师naval architecture 造船工程naval ship 军船naval architecture 造船学nearuniversal gear 准万向齿轮network flow 网络流程neutral equilibrium 中性平衡normal 法向，法向的，正交的normal force 法向力normal operating condition 常规(正常)运作工况notch 开槽，开凹口Off the shelf 成品的，畅销的，流行的off-center loading 偏移中心的装载offsets 型值offshore drilling 离岸钻井oil-rig 钻油架operational requirement 军事行动需求，运作要求orient 取向，定方位，调整orthogonal 正交的，矩形的out strake 外列板outboard profile 侧视图outfit 舾装outfitter 舾装工outfitting 舾装overall stability 总体稳性overhang 外悬overstocking 存货过剩owner’s staff 船东的雇(职)员paint priming 涂底漆Panama Canal 巴拿马运河panel line system 板材生产线系统parallel middle body 平行中体patternmaker 木模工payload 有效载荷permanent body 永久性组织机构perpendicular（船艏、艉）柱，垂直的，正交的pillar 支柱pin 钉，销pin jig 限位胎架pintle 销，枢轴pipe fitter 管装工pipe laying barge (海底) 铺管驳船piping 管路pitch 纵摇plan views 设计图planing hull 滑行船体pleasure ship 游乐用船Plimsoll line 普林索尔载重线polar-exploration craft 极地考察船Polaris (submarine) 北极星级(潜艇)port 左舷portable gate 移动式(可移动)闸门positive righting arm 扶正力臂power and lighting system 动力与照明系统preliminary design 初步设计preliminary/concept design 初步/概念设计pressure vessel 压力容器principal dimensions 主尺度prism 棱柱体prismatic coefficient 棱形系数procurement 采购，获得Program Evaluation and Review Technique 规划评估与复核法quartering sea 尾斜浪, 从船斜后方来的浪quay(横)码头，停泊所racking 倾斜，变形，船体扭转变形radiography X射线照相术，X射线探伤rake 倾角,倾斜ram pressure 速压头，冲压，全压力rectangle 矩形reenlistment 重征服役Registo Italiano Navale (意大利)船级社remedial action 补救措施reserve buoyancy 储备浮力reserve buoyancy 储备浮力residuary resistance 剩余阻力resultant 合力resultant 合力retract 收进revolving crane 旋转式(鹤)吊，转臂吊(车)Reynolds number 雷诺数rigger 索具装配工rigid side walls 刚性侧壁rise of floor 底升risk 保险对象，保险金额rivering warfare vessel 内河舰艇rivet 铆接，铆钉roll 横摇rolled angle butt (轧制)角钢焊接头roll-on/roll-off(RO-RO) 滚装rough sea 汹涌的波浪round of beam 梁拱rounded gunwale 修园的舷边rubber tile 橡皮瓦rudder post 舵柱rudder 舵rudder rate 舵率rudder stock 舵杆run 去流段Sag 中垂sagging 中垂scale 缩尺，尺度，尺scale model 缩尺船模scantling 材积sea keeping performance 耐波性能seasickness 晕船seaworthiness 适航性section 剖面，横剖面sections (铁、钢)型材，轧材self-induced 自身诱导的semi finished item 半精加工件semisubmersible drilling rig 半潜式钻井架set course 设定的航线set course 设定航线shaft bossing 轴包套shaft bracket 轴支架shear 剪切，剪力sheer aft 艉舷弧sheer forward 艏舷弧sheer drawing 剖面图sheer plane 纵剖面sheer profile 纵剖线sheer profile 纵剖图sheer(甲板)舷弧sheet metal work 钣金工，冷作工shell plating 船壳板shell 船壳板ship fitter 船舶装配工ship fitter 船体安装工ship fitter 舰船装配工ship form 船型ship Hydrodynamics 水动力学ship owner 船东shipping line 船运航线shipway (造)船台shipwright 船体装配工，造船工人shipyard 船厂shipyard 船厂shipyard schedule chart 船厂施工进度图shoring 支撑，支柱shoulder 船肩sideways 朝侧向six degrees of freedom 六自由度sizable 相当大的skirt（气垫船）围裙slamming 砰击，拍击slice 一部分，薄片sloping shipway 有坡度船台，滑道soft chine 圆舭spare part 备件specially prepared form 专门(特殊)加工的模板spectrum 谱speed-to-length ratio 速长比stability 稳性stable equilibrium 稳定平衡standard 规章starboard 右舷static equilibrium 静平衡statically determinant 静定的statistical 统计学(上)的steel marking 钢板划线steering gear 操纵装置steering gear 操纵装置，舵机stem 船艏stem contour 艏柱型线stern 艉stern frame 艉构架，艉框架stern wave 艉波stiffen 加劲，加强stiffener 肋骨strain 应变strake 船体列板stringent safety regulations 严格的安全规章structural alignment 结构校准，组合，组装strut 支柱，支撑构形subassembly (局部)分部装配subdivision 分舱sublet 转包，分包，转租submersible 潜器suction cup 吸盘Suez Canal Tonnage 苏伊士运河吨位限制summer load water line 夏季载重水线super cavitating propeller超空泡螺旋桨superintendent 监督管理人，总段长，车间主任superstructure 上层建筑supertanker 超级油轮supervision of the Society’s surveyor 船级社验船师的监造surface piercing 穿透水面的surface preparation and coating 表面加工处理与喷涂surge 纵荡surmount 顶上覆盖，越过survivability 生存力SWATCH(Small Waterplane Area Twin Hull) 小水线面双体船sway 横荡switchboard 控制台，开关板tabular freeboard 列成表格的干舷值tacker 定位搭焊工talking paper 讨论文件tangential viscous force 切向粘性力tanker 油轮tanker 油轮tantamount 等值的，相当的taper 弄细，变尖tee T形构件，三通管template 样板tensile stress 拉(张)应力The Register of Shipping of the People’s Republic of China 中国船舶检验局The Titanic 泰克尼克号(巨型邮轮)there is more shape to the shell 船壳板的形状较复杂titanic 巨大的to be craft oriented 与行业有关的，适应于行业性的to run the waterlines 绘制水线toed towards amidships 趾部朝向船舯ton gross=gross ton 长吨=1. 016公吨tonnage 吨位torque 扭矩torsio 扭转的trade 工种, 贸易trailer type transporter 拖车式载运车transfer sideways 横向移动transom (stern) 方尾transverse 横向的transverse bulkhead plating 横隔舱壁板transverse section 横剖面transverse stability 横稳性trawling 拖网trial 实船试验trim 纵倾trim 纵倾trim by the stern/bow 艉/艏倾trimaran 三体船trough 波谷tugboat 拖船tumble home(船侧)内倾Type A ship A类船U form U型U. S. Coast Guard 美国海岸警卫队ULCC(Ultra Large Crude Carrier）超级大型原油轮（载重量>40万吨）ultrasonic 超声波的\underwriter (海运)保险商undock 使船出坞upright position 正浮位置V shaped V型的ventilation and air conditioning diagram 通风与空调敷设设计图vertical prismatic coefficient 垂向棱形系数vertical prismatic coefficient 垂向棱形系数vicinity 邻近，附近villain 坏人，罪魁viscosity 粘性VLCC(Very Large Crude Carrier）巨型（原）油轮（载重量>20万吨）V-sectionV型剖面wash 下洗 ,艉流water line 水线waterborne 浮于水上的，水基的waterplane 水线面waterplane area coefficient 水线面积系数watertight integrity 水密完整性wave pattern 波型wavemaking resistance 兴波阻力weather deck 露天甲板weld inspection 焊缝检测welder 焊工weldment 焊件，焊接装配wetted surface 湿面积wing shaft 侧轴yacht 快艇yard issue 船厂开工任务发布书yaw 艏摇yaw 艏摇，摇艏。

IMO(Intergovernmental Maritime Organization)国际海事组织IMCO(Intergovernmental Maritime Consultative Organization)国际海事质询组织International Towing Tank Conference (ITTC) 国际船模试验水池会议International Association of Classification Society (IACS) 国际船级社协会ABS(American Bureau of Shipping) 美国船级社BV(Bureau Veritas) 法国船级社Lloyd's Register of shipping 英国劳埃德船级社RINA(Registo Italiano Navade) 意大利船级社Load Line Convention 载重线公约Lloyd's Rules 劳埃德规范Register （船舶）登录簿，船名录Green Book 绿皮书，19世纪英国另一船级社的船名录，现合并与劳埃德船级社，用于登录快速远洋船Supervision of the Society's surveyor 船级社验船师的监造书Merchant Shipbuilding Return 商船建造统计表BSRA 英国船舶研究协会HMS 英国皇家海军舰艇CAD(computer-aided design) 计算机辅助设计CAE(computer-aided manufacturing) 计算机辅助制造CAM(computer-aided engineering) 计算机辅助工程CAPP(computer -aided process planning) 计算机辅助施工计划制定IAGG(interactive computer graphics) 交互式计算机图像技术a faired set of lines 经过光顺处理的一套型线a stereo pair of photographs 一对立体投影相片abaft 朝向船体abandonment cost 船舶废置成本费用accommodation 居住（舱室）accommodation ladder 舷梯adjust valve 调节阀adjustable-pitch 可调螺距式admiralty 海军部advance coefficient 进速系数aerostatic 空气静力学的aft peak bulkhead 艉尖舱壁aft peak tank 艉尖舱aileron 副鳍air cushion vehicle 气垫船air diffuser 空气扩散器air intake 进气口aircraft carrier 航空母舰air-driven water pump 气动水泵airfoil 气翼，翼剖面，机面，方向舵alignment chock 组装校准用垫楔aluminum alloy structure 铝合金结构amidships 舯amphibious 两栖的anchor arm 锚臂anchor chain 锚链anchor crown 锚冠anchor fluke 锚爪anchor mouth 锚唇anchor recess锚穴anchor shackle 锚卸扣anchor stock 锚杆angle bar/plate 角钢angle of attack 攻角angled deck 斜角甲板anticipated loads encountered at sea 在波浪中遭遇到的预期载荷anti-pitching fins 减纵摇鳍antiroll fins 减摇鳍anti-rolling tank 减摇水舱appendage 附体artisan 技工assembly line 装配流水线at-sea replenishment 海上补给augment of resistance 阻力增额auxiliary systems 辅机系统auxiliary tank 调节水舱axial advance 轴向进速backing structure 垫衬结构back-up member 焊接垫板balance weight 平衡锤ball bearing 滚珠轴承ball valve 球阀ballast tank 压载水舱bar 型材bar keel 棒龙骨，方龙骨，矩形龙骨barge 驳船base line 基线basic design 基本设计batten 压条，板条beam 船宽，梁beam bracket 横梁肘板爱beam knee 横梁肘板bearing 轴承bed-plate girder 基座纵桁bending-moment curves 弯矩曲线Benoulli's law 伯努利定律berth term 停泊期bevel 折角bidder 投标人bilge 舭，舱底bilge bracket 舭肘板bilge radius 舭半径bilge sounding pipe 舭部边舱水深探管bitt 单柱系缆桩blade root 叶跟blade section 叶元剖面blast 喷丸block coefficient 方形系数blue peter 出航旗boarding deck 登艇甲板boat davit 吊艇架boat fall 吊艇索boat guy 稳艇索bobstay 首斜尾拉索body plan 横剖面图bolt 螺栓，上螺栓固定Bonjean curve 邦戎曲线boom 吊杆boss 螺旋桨轴榖bottom side girder 旁底桁bottom side tank 底边舱bottom transverse 底列板boundary layer 边界层bow line 前体纵剖线bow wave 艏波bowsprit 艏斜桅bow-thruster 艏侧推器box girder 箱桁bracket floor 框架肋板brake 制动装置brake band 制动带brake crank arm 制动曲柄brake drum 刹车卷筒brake hydraulic cylinder 制动液压缸brake hydraulic pipe 刹车液压管breadth extreme 最大宽，计算宽度breadth moulded 型宽breakbulk 件杂货breasthook 艏肘板bridge 桥楼，驾驶台bridge console stand 驾驶室集中操作台buckle 屈曲buffer spring 缓冲弹簧built-up plate section 组合型材bulb plate 球头扁钢bulbous bow 球状船艏，球鼻首bulk carrier 散货船bulk oil carrier 散装油轮bulkhead 舱壁bulwark 舷墙bulwark plate 舷墙板bulwark stay 舷墙支撑buoy tender 航标船buoyant 浮力的buoyant box 浮箱butt weld 对缝焊接butterfly screw cap 蝶形螺帽buttock 后体纵剖线by convention 按照惯例，按约定cable ship 布缆船cable winch 钢索绞车camber 梁拱cant beam 斜横梁cant frame 斜肋骨cantilever beam 悬臂梁capacity plan 舱容图capsize 倾覆capsizing moment 倾覆力臂captain 船长captured-air-bubble vehicle 束缚气泡减阻船cargo cubic 货舱舱容，载货容积cargo handling 货物装卸carriage 拖车，拖架cast steel stem post 铸钢艏柱catamaran 高速双体船，双体的cavitation 空泡cavitation number 空泡数cavitation tunnel 空泡水筒center keelson 中内龙骨centerline bulkhead 中纵舱壁centroid 型心，重心，质心，矩心chain cable stopper 制链器chart 海图charterer 租船人chief engineer 轮机长chine 舭，舷，脊chock 导览钳CIM(computer integrated manufacturing) 计算机集成组合制造circulation theory 环流理论classification society 船级社cleat 系缆扣clipper bow 飞剪型船首clutch 离合器coastal cargo 沿海客货轮cofferdam 防撞舱壁combined cast and rolled stem 混合型艏柱commercial ship 营利用船commissary spaces 补给库舱室，粮食库common carrier 通用运输船commuter 交通船compartment 舱室compass 罗经concept design 概念设计connecting tank 连接水柜constant-pitch propeller 定螺距螺旋桨constraint condition 约束条件container 集装箱containerized 集装箱化contract design 合同设计contra-rotating propellers 对转桨controllable-pitch 可控螺距式corrosion 锈蚀，腐蚀couple 力矩，力偶crane 克令吊，起重机crank 曲柄crest (of wave) 波峰crew quarters 船员居住舱criterion 判据，准则Critical Path Method 关键路径法cross-channel automobile ferries 横越海峡车客渡轮cross-sectional area 横剖面面积crow's nest 桅杆瞭望台cruiser stern 巡洋舰尾crussing range 航程cup and ball joint 球窝关节curvature 曲率curves of form 各船形曲线cushion of air 气垫damage stability 破损稳性damper 缓冲器damping 阻尼davit arm 吊臂deadweight 总载重量de-ballast 卸除压载deck line at side 甲板边线deck longitudinal 甲板纵骨deck stringer 甲板边板deck transverse 强横梁deckhouse 舱面室，甲板室deep v hull 深v型船体delivery 交船depth 船深derrick 起重机，吊杆design margin 设计余量)design spiral 设计螺旋循环方式destroyer 驱逐舰detachable shackle 散合式连接卸扣detail design 详细设计diagonal stiffener 斜置加强筋diagram 图，原理图，设计图diesel engine 柴油机dimensionless ratio 无量纲比值displacement 排水量displacement type vessel 排水型船distributed load 分布载荷division 站，划分，分隔do work 做功dock 泊靠double hook 山字钩double iteration procedure 双重迭代法double roller chock 双滚轮式导览钳double-acting steam cylinder 双向作用的蒸汽气缸down halyard 降帆索draft 吃水drag 阻力，拖拽力drainage 排水draught 吃水，草图，设计图，牵引力爱dredge 挖泥船drift 漂移，偏航drilling rig 钻架drill ship 钻井船drive shaft 驱动器轴driving gear box 传动齿轮箱driving shaft system 传动轴系dry dock 干船坞ducted propeller 导管螺旋桨dynamic supported craft 动力支撑型船舶dynamometer 测力计，功率计e.h.p 有效马力eccentric wheel 偏心轮echo-sounder 回声探深仪eddy 漩涡eddy-making resistance 漩涡阻力efficiency 供给能力，供给量electrohydraulic 电动液压的electroplater 电镀工elevations 高度，高程，船型线图的侧面图，立视图，纵剖线图，海拔empirical formula 经验公式enclosed fabrication shop 封闭式装配车间enclosed lifeboat 封闭式救生艇end open link 末端链环end shackle 末端卸扣endurance 续航力，全功率工作时间engine room frame 机舱肋骨engine room hatch end beam 机舱口端梁ensign staff 船尾旗杆entrance 进流段erection 装配，安装exhaust valve 排气阀expanded bracket 延伸肘板expansion joint 伸缩接头extrapolate 外插fair 光顺faised floor 升高肋板fan 鼓风机fatigue 疲劳feasibility study 可行性研究feathering blade 顺流变距桨叶fender 护舷ferry 渡轮，渡运航线fillet weld connection 贴角焊连接fin angle feedback set 鳍角反馈装置fine fast ship 纤细高速船fine form 瘦长船型finite element 有限元fire tube boiler 水火管锅炉fixed-pitch 固定螺距式flange 突边，法兰盘flanking rudders 侧翼舵flap-type rudder 襟翼舵flare 外飘，外张flat of keel 平板龙骨fleets of vessels 船队flexural 挠曲的floating crane 起重船floodable length curve 可进长度曲线flow of materials 物流flow pattern 流型，流线谱flush deck vessel 平甲板型船flying bridge 游艇驾驶台flying jib 艏三角帆folding batch cover 折叠式舱口盖folding retractable fin stabilizer 折叠收放式减摇鳍following edge 随边following ship 后续船foot brake 脚踏刹车fore peak 艏尖舱forged steel stem 锻钢艏柱forging 锻件，锻造forward draft mark 船首水尺forward/after perpendicular 艏/艉柱forward/after shoulder 前/后肩foundry casting 翻砂铸造frame 船肋骨，框架，桁架frame spacing 肋骨间距freeboard 干舷freeboard deck 干舷甲板freight rate 运费率fresh water loadline 淡水载重线frictional resistance 摩擦阻力Froude number 傅汝德数fuel/water supply vessel 油水供给船full form丰满船型full scale 全尺度fullness 丰满度funnel 烟囱furnishings 内装修gaff 纵帆斜桁爱gaff foresail 前桅主帆gangway 舷梯gantt chart 甘特图gasketed openings 装以密封垫的开口general arrangement 总布置general cargo ship 杂货船generatrix 母线geometrically similar form 外形相似船型girder 桁梁，桁架girder of foundation 基座纵桁governmental authorities 政府当局，管理机构gradient 梯度graving dock 槽式船坞gross ton 长吨（1.016公吨，short for GT）group technology 成组建造技术guided-missile cruiser 导弹巡洋舰gunwale 船舷上缘gunwale angle 舷边角钢gunwale rounded thick strake 舷边圆弧厚板guyline 定位索gypsy 链轮gyro-pilot steering indicator 自动操舵操纵台gyroscope 回转仪half breadth plan 半宽图half depth girder 半深纵骨half rounded flat plate 半圆扁钢hard chine 尖舭hatch beam sockets 舱口梁座hatch coaming 舱口围板hatch cover 舱口盖（板）hatch cover rack 舱口盖板隔架hatch side cantilever 舱口悬臂梁hawse pipe 锚链桶hawsehole 锚链孔heave 垂荡heel 横倾heel piece 艉柱根helicoidal 螺旋面的，螺旋状的hinge 铰链hinged stern door 艉部吊门hog 中拱hold 船舱homogeneous cylinder 均质柱状体hopper barge 倾卸驳horizontal stiffener 水平扶强材hub 桨毂，轴毂，套筒hull form 船型，船体外形hull girder stress 船体桁应力HV AC(heating ventilating and cooling) 取暖，通风与冷却hydraulic mechanism 液压机构hydrodynamic 水动力学的hydrofoil 水翼hydrostatic 水静力的icebreaker 破冰船immerse 浸水，浸没impact load 冲击载荷imperial unit 英制单位in strake 内列板inboard profile 纵剖面图incremental plasticity 增量塑性independent tank 独立舱柜initial stability at small angle of inclination 小倾角初稳性inland waterways vessel 内河船inner bottom 内底in-plane load 面内载荷intact stability 完整稳性intercostals 肋间的，加强的intersection 交点，交叉，横断（切）inventory control 存货管理iterative process 迭代过程jack 船首旗jack 千斤顶joinery 细木工keel 龙骨keel laying 开始船舶建造kenter shackle 双半式连接链环Kristen-Boeing propeller 正摆线推进器landing craft 登陆艇launch 发射，下水launch 汽艇launching equipment （向水中）投放设备leading edge 导缘，导边ledge 副梁材length overall 总长leveler 调平器，矫平机life saving appliance 救生设备lifebuoy 救生圈lifejacket 救生衣lift fan 升力风扇lift offsets 量取型值light load draft 空载吃水lightening hole 减轻孔light-ship 空船limbers board 舭部污水道顶板liner trade 定期班轮营运业lines 型线lines plan 型线图Linnean hierarchical taxonomy 林式等级式分类学liquefied gas carrier 液化气运输船liquefied natural gas carrier 液化天然气船liquefied petroleum gas carrier 液化石油气船liquid bulk cargo carrier 液体散货船liquid chemical tanker 液体化学品船living and utility spaces 居住与公用舱室load line regulations 载重线公约，规范load waterplane 载重水线面loft floor 放样台longitudinal (transverse) 纵（横）稳心高longitudinal bending 纵总弯曲longitudinal prismatic coefficient 纵向棱形系数longitudinal strength 总纵强度longitudinally framed system 纵骨架式结构luffing winch 变幅绞车machinery vendor 机械（主机）卖方magnet gantry 磁力式龙门maiden voyage 处女航main impeller 主推叶轮main shafting 主轴系major ship 大型船舶maneuverability 操纵性manhole 人孔margin plate 边板mark disk of speed adjusting 速度调整标度盘mast 桅杆mast clutch 桅座matrix 矩阵merchant ship 商船metacenter 稳心metacentric height 稳心高metal plate path 金属板电镀槽metal worker 金属工metric unit 公制单位middle line plane 中线面midship section 舯横剖面midship section coefficient 中横剖面系数ML 物资清单，物料表model tank 船模试验水池monitoring desk of main engine operation 主机操作监视台monitoring screen of screw working condition 螺旋桨运转监视屏more shape to the shell 船壳板的形状复杂mould loft 放样间multihull vessel 多体船multi-purpose carrier 多用途船multi-ship program 多种船型建造规划mushroom ventilator 蘑菇形通风桶mutually exclusive attribute 相互排它性的属性N/C 数值控制nautical mile 海里naval architecture 造船学navigation area 航区navigation deck 航海甲板near-universal gear 准万向舵机，准万向齿轮net-load curve 静载荷曲线neutral axis 中性轴，中和轴neutral equilibrium 中性平衡non-retractable fin stabilizer 不可收放式减摇鳍normal 法向的，正交的normal operating condition 常规运作状况nose cone 螺旋桨整流帽notch 开槽，开凹口oar 橹，桨oblique bitts 斜式双柱系缆桩ocean going ship 远洋船off-center loading 偏离中心的装载offsets 型值offshore drilling 离岸钻井offshore structure 离岸工程结构物oil filler 加油点oil skimmer 浮油回收船oil-rig 钻油架on-deck girder 甲板上桁架open water 敞水optimality criterion 最优性准则ore carrier 矿砂船orthogonal 矩形的orthogonal 正交的out strake 外列板outboard motor 舷外机outboard profile 侧视图outer jib 外首帆outfit 舾装outfitter 舾装工outrigger 舷外吊杆叉头overall stability 总体稳性overhang 外悬paddle 桨paddle-wheel-propelled 明轮推进的Panama Canal 巴拿马运河panting arrangement 强胸结构，抗拍击结构panting beam 强胸横梁panting stringer 抗拍击纵材parallel middle body 平行中体partial bulkhead 局部舱壁payload 有效载荷perpendicular 柱，垂直的，正交的photogrammetry 投影照相测量法pile driving barge 打桩船pillar 支柱pin jig 限位胎架pintle 销，枢轴pipe fitter 管装工pipe laying barge 铺管驳船piston 活塞pitch 螺距ipitch 纵摇plan views 设计图planning hull 滑行船体Plimsoll line 普林索尔载重线polar-exploration craft 极地考察船poop 尾楼port 左舷port call 沿途到港停靠positive righting moment 正扶正力矩power and lighting system 动力与照明系统precept 技术规则preliminary design 初步设计pressure coaming 阻力式舱口防水挡板principal dimensions 主尺度Program Evaluation and Review Technique 规划评估与复核法progressive flooding 累进进水project 探照灯propeller shaft bracket 尾轴架爱propeller type log 螺旋桨推进器测程仪PVC foamed plastic PVC泡沫塑料quadrant 舵柄quality assurance 质量保证quarter 居住区quarter pillar 舱内侧梁柱quartering sea 尾斜浪quasi-steady wave 准定长波quay 码头，停泊所quotation 报价单racking 倾斜，变形，船体扭转变形radiography X射线探伤rake 倾斜raked bow 前倾式船首raster 光栅refrigerated cargo ship 冷藏货物运输船regulating knob of fuel pressure 燃油压力调节钮reserve buoyancy 储备浮力residuary resistance 剩余阻力resultant 合力reverse frame 内底横骨Reynolds number 雷诺数right-handed propeller 右旋进桨righting arm 扶正力臂，恢复力臂rigid side walls 刚性侧壁rise of floor 底升riverine warfare vessel 内河舰艇rivet 铆接，铆钉roll 横摇roll-on/roll-off (Ro/Ro) 滚装rotary screw propeller 回转式螺旋推进器9 rounded gunwale 修圆的舷边rounded sheer strake 圆弧舷板rubber tile 橡皮瓦rudder 舵rudder bearing 舵承rudder blade 舵叶rudder control rod 操舵杆rudder gudgeon 舵钮rudder horn 挂舵臂rudder pintle 舵销rudder post 舵柱rudder spindle 舵轴rudder stock 舵杆rudder trunk 舵杆围井run 去流段sag 中垂salvage lifting vessel 救捞船scale 缩尺，尺度schedule coordination 生产规程协调schedule reviews 施工生产进度审核screen bulkhead 轻型舱壁Sea keeping performance 耐波性能sea spectra 海浪谱sea state 海况seakeeping 适航性seasickness 晕船seaworthness 适航性seaworthness 适航性section moulus 剖面模数section 剖面，横剖面self-induced 自身诱导的self-propulsion 自航semi-balanced rudder 半平衡舵semi-submersible drilling rig 半潜式钻井架shaft bossing 轴榖shaft bracket 轴支架shaft coupling 联轴节shear 剪切，剪力shear buckling 剪切性屈曲shear curve 剪力曲线sheer 舷弧sheer aft/forward 艉/艏舷弧sheer drawing 剖面图sheer plane 纵剖面sheer profile 总剖线，纵剖图shell plating 船壳板ship fitter 船舶装配工ship hydrodynamics 船舶水动力学shipway/slipway 船台shipyard 船厂shrouded screw 有套罩螺旋桨，导管螺旋桨side frame 舷边肋骨side keelson 旁内龙骨side plate 舷侧外板side stringer 甲板边板single-cylinder engine 单缸引擎sinkage 升沉six degrees of freedom 六自由度skin friction 表面摩擦力skirt （气垫船）围裙slamming 砰击sleeve 套管，套筒，套环slewing hydraulic motor 回转液压马达slice 一部分，薄片sloping shipway 有坡度船台sloping top plate of bottom side tank 底边舱斜顶板sloping bottom plate of topside tank 顶边舱斜底板soft chine 圆舭sonar 声纳spade rudder 悬挂舵spectacle frame 眼睛型骨架speed-to-length ratio 速长比sponson deck 舷伸甲板springing 颤振stability 稳性stable equilibrium 稳定平衡starboard 右舷static equilibrium 静平衡steamer 汽轮船steering gear 操纵装置，舵机stem 船艏stem contour 艏柱型线stern 船艉stern barrel 尾拖网滚筒stern counter 尾突体stern ramp 尾滑道，尾跳板爱stern transom plate 尾封板stern wave 艉波stiffen 加劲，加强stiffener 扶强材，加劲杆straddle 跨立，外包式叶片strain 应变strake 船体列板streamline 流线streamlined casing 流线型套管strength curves 强度曲线strength deck 强力甲板stress concentration 应力集中structural instability 结构不稳定性strut 支柱，支撑构型subassembly 分部装配subdivision 分舱submerged nozzle 浸没式喷口submersible 潜期suction back of a blade 桨叶片抽吸叶背Suez Canal tonnage 苏伊士运河吨位限制summer load water line 夏季载重水线superintendent 监督管理人，总段长，车间主任superstructure 上层建筑supper cavitating propeller 超空泡螺旋桨surface nozzle 水面式喷口surface piercing 穿透水面的surface preparation and coating 表面预处理与喷涂surge 纵荡sway 横荡yaw 首摇surmount 顶上覆盖，越过swage plate 压筋板swash bulkhead 止荡舱壁SWATH (Small Waterplane Area Twin Hull) 小水线面双体船tail-stabilizer anchor 尾翼式锚talking paper 讨论文件tangential 切向的，正切的tangential viscous force 切向粘性力tanker 油船tender 交通小艇timber carrier 木材运输船tugboat 拖船tee T型构件，三通管tensile stress 拉（张）应力thermal effect 热效应throttle valve 节流阀throughput 物料流量thrust 推力thruster 推力器，助推器tip of a blade 桨叶叶梢toed towards amidships 趾部朝向船舯tonnage 吨位torpedo 鱼雷torque 扭矩trailing edge 随边transom stern 方尾transverse bulkhead plating 横隔舱壁板transverse section 横剖面transverse stability 横稳性trawling 拖网trial 实船试验trim 纵倾trim by the stern/bow 艉/艏倾trimaran 三体的tripping bracket 防倾肘板trough 波谷tumble home （船侧）内倾tunnel wall effect 水桶壁面效应turnable blade 可转动式桨叶turnable shrouded screw 转动导管螺旋桨tweendeck cargo space 甲板间舱tweendedk frame 甲板间肋骨two nodded frequency 双节点频率LCC 大型原油轮ULCC 超级大型原油轮VLCC 巨型原油轮ultrasonic 超声波的underwriter （海运）保险商unsymmetrical 非对称的upright position 正浮位置vapor pocket 气化阱ventilation and air conditioning diagram 通风与空调铺设设计图Venturi section 文丘里试验段vertical prismatic coefficient 横剖面系数vertical-axis(cycloidal)propeller 直叶（摆线）推进器vessel component vender 造船部件销售商viscosity 粘性V oith-Schneider propeller 外摆线直翼式推进器vortex 梢涡v-section v型剖面wake current 伴流，尾流water jet 喷水（推进）管water plane 水线面watertight integrity 水密完整性wave pattern 波形wave suppressor 消波器，消波板wave-making resistance 兴波阻力weather deck 露天甲板web 腹板web beam 强横梁web frame 腹肋板welder 焊工wetted surface 湿表面积winch 绞车windlass 起锚机wing shaft 侧轴wing-keel 翅龙骨（游艇）working allowance 有效使用修正量worm gear 蜗轮，蜗杆yacht 快艇yard issue 船厂开工任务发布书yards 帆桁--。

船舶与海洋工程英语船舶与海洋工程涉及到设计、建造和运营各种类型的船舶以及与海洋资源开发和保护相关的工程。

以下是有关船舶与海洋工程的一些英语词汇和短语：1. Ship Design and Construction:- Naval architecture - 船舶设计- Shipbuilding - 船舶建造- Hull design - 船体设计- Marine engineering - 海洋工程2. Ship Types:- Cargo ship - 货船- Container ship - 集装箱船- Passenger ship - 客船- Oil tanker - 油轮- Fishing vessel - 渔船- Naval ship - 军舰3. Maritime Safety:- Navigation safety - 航行安全- Collision avoidance - 避碰- Search and rescue - 搜救- Emergency response - 应急响应4. Offshore Engineering:- Offshore platform - 海上平台- Subsea engineering - 海底工程- Offshore drilling - 海上钻探- Floating production storage and offloading (FPSO) - 浮式生产储油船5. Oceanography:- Ocean currents - 海洋流- Tidal energy - 潮汐能- Marine ecology - 海洋生态学- Underwater exploration - 水下探测6. Marine Resources:- Fisheries management - 渔业管理- Aquaculture - 水产养殖- Deep-sea mining - 深海矿业- Renewable ocean energy - 可再生海洋能源7. Environmental Protection:- Marine pollution control - 海洋污染控制- Oil spill response - 油污应急响应- Marine conservation - 海洋保护- Sustainable maritime practices - 可持续海洋实践8. International Maritime Organizations:- International Maritime Organization (IMO) - 国际海事组织- International Hydrographic Organization (IHO) - 国际海洋测绘组织- International Maritime Satellite Organization (INMARSAT) - 国际海事卫星组织这些词汇和短语涵盖了船舶与海洋工程领域的一些关键方面，可以作为学习和讨论的起点。

船舶海洋工程专业词汇船舶海洋工程专业词汇一、总体1. 1一般术语 General Definition①主要船级社Major Classification Societies中国船级社China Classification Societies(CCS)美国船级社 American Bureau of Shipping (ABS)劳氏船级社Lloyd’s Register of Shipping(LR)法国船级社 Bureau Veritas(BV)挪威船级社 Det Norske Veritas(DNV)意大利船级社Registro Italiano Navale(RINA)日本海事协会 Nippon Kaiji Kyokai (NKK)俄罗斯船舶登记局Russia Register of Shipping (RR)德国劳氏船级社 Germanischer Lloyd (GL)波兰船级社 Polski Rejestr Statkow (PRS)破损检验 damage survey坞内检验 docking survey干坞内检验 dry-docking survey一般检验 general survey不完全检验 incomplete survey中间检验 intermediate survey水上检验 in-water survey负载检验 loading survey载重线检验 load line survey部分检验 partial survey定期检验 periodical survey延期检验 postponement survey特殊检验 special survey法定发证检验 statutory and certificate survey④验船师 ship surveyor总验船师 principal surveyor⑤平台类型 type of platform固定式平台 fixed platform导管架式平台 jacket platform移动式平台 mobile platform自升式平台 jack-up platformelevating platform沉垫自升式平台mat-supported jack-up platform桩腿自升式平台self-elevating jack-up platform with leg桩鞋自升式平台self-elevating jack-up platform with shoe单桩自升式平台 monopod jack-up platform 桩稳式平台 column stabilized platform半潜式平台 semi-submerged platform坐底式平台 bottom-submerged platform浮船式平台 floating platform张力腿式平台 tension-leg platform重力式平台 gravity platform重力塔式平台 gravity tower platform牵索塔式平台 guyed tower platform钻井平台 drilling platform生产平台 production platform井口平台 well head platform油井平台 well platform缆系平台 tethered platform系泊平台 mooring platform储油平台 oil storage platform油气处理平台 process(ing) platform集输平台 gathering of pumping platform 居住平台 accommodation platformquarters platformliving platform⑥浮态afloat [floating] condition浮心 center of buoyancy纵倾 longitudinal trim纵倾力矩 trim moment纵稳心 longitudinal metacenter [LGM]纵稳心半径 longitudinal metacenter radius 纵稳心高 longitudinal metacenter height [LMH]纵稳性 longitudinal stability横倾 heel横倾力矩 heeling moment横稳心 transverse metacenter [TGM]横稳心半径 transverse metacenter radius横稳心高transverse metacenter height [TMH]横稳性 transverse stability⑦总纵弯曲 overall longitudinal bending总纵强度 longitudinal strength总重 gross weight总载荷 overall loading总体设计 overall system design总体性能 overall performance总吨位 gross tonnage [GT]净吨位 net tonnage [NT]漂心 center of floatation重心 center of gravity方形系数 block coefficient [CB]舱容系数 coefficient of stowage⑧正常工作状态operating condition自存状态survival condition1. 2环境条件environment conditions①风 wind风速 wind velocity (向量) [WV]wind speed（非向量）[WS]风力 wind force [strength]风向 wind direction [WD]风压 wind pressure风力矩 wind moment设计风速 design wind speed极限风速 extreme wind speed②波浪 wave有限振幅波 wave of finite amplitude艾里波 Airy wave余弦波 cosine wave椭圆余弦波 cnoidal wave斯托克斯五阶波 Stokes fifth-order wave 波峰 wave crest波谷 wave-troughwave-hollow波高 wave-height波长 wavelength波周期 wave period波浪谱 wave spectrum③海流 current流速 current velocity流速仪 current log流向 current direction流压 current pressure④冰 ice流冰 drift ice, floating ice 堆积冰厚 consolidated pack ice 堆积冰 hummocked ice冰原 ice-field冰厚 ice thickness⑤潮汐 tide潮位 tidal level潮差 tidal range潮间带 inertial zone, tideland 天文潮 astronomical tide风暴潮 storm tide退潮 ebb tide, falling tide涨潮 flood tide, rising tide 高潮 high tide低潮 low tide最低潮 dead tide半日潮 semidiurnal tide全日潮 single day tide⑥温度 temperature大气温度 atmospheric temperature环境温度 environment temperature底层水温 bottom temperature海面水温 bucket temperature, sea surface ⑦地震 earthquake, seism地震烈度 seismic intensity1. 3主要指标①长度 length总长 overall length [LOA]型长 molded length两柱间长水线间长②宽度 breadth总宽 overall breadth型宽 molded breadth③深度 depth总深 total depth型深 molded depth④吃水 draft总吃水total draft型吃水molded draft⑤排水量displacement总排水量total displacement型排水量molded displacement⑥排水体积 displacement volume 总排水体积total displacement volume型排水体积molded volume of displacement⑦水深 water depth⑧入泥深度 bottom penetration⑨空气间隙 air gap⑩定员 accommodate, complement ⑪自持力endurance, self-supportability⑫续航力range ability1. 4图纸名称①总布置图general arrangement plan②甲板载荷图d eck l oad plan③危险区划分图danger area division plan④防火控制图fire control plan⑤静水力曲线图displacement and other curves⑥综合稳性曲线图compl ex stability diagram稳性横交曲线stability cross- curves稳性曲线stability curve稳性力臂stability arm稳性力矩stability moment稳性消失角angl e of vanishing stability稳性衡准stability criteria稳性衡准数fundamental stabilitycriterion numeral恢复力矩restitute moment风倾力矩wind heeling moment⑦型线图lines drawing型线mol d ed lines型值offsets型值表tabl e of offsets1. 5资料名称①设计任务书d esign specifications②主体及设备说明书general instructions of platform and equipment③图纸目录drawing list④环境条件资料specifications of environment conditions⑤甲板载荷说明书specifications of d eck l oad⑥防腐计算anticorrosion cal culation &instruction⑦外载荷计算书external l oads calculation⑧重量重心计算书center of gravity weight cal culation⑨完整稳性计算书intact stability cal culation ⑩着底稳性计算书account of stability in bottomed cal culation⑪破损稳性计算书damaged stability cal culation⑫静水力计算书hydrostatic cal culation⑬舱容计算书storage capacity account⑭干舷计算书free board cal culation⑮拖航马力计算书towage resistance and horsepower cal culation⑯极限承载力计算书cal culation of extreme bearing capacity of sea bed⑰倾斜试验大纲inclining experiment program⑱操作手册information and operation instruction manual1. 6舱室名称①开敞甲板open (weather) d eck②走廊aisl e③上层建筑superstructures④甲板室d eckhouse⑤公司办公室company office⑥承包商办公室contractor office⑦中央控制室control center room⑧液压控制室hydraulic control room⑨升降控制室jacking control room⑩生活住室living compartment (accommodation)⑪会议室meeting (conference) room⑫通讯室radio room⑬医务室medical officer’s cabin⑭病房sick bay⑮厨房gall ey⑯餐厅mess room, dining room⑰卫生间toil et⑱更衣室cl oth changing room⑲淋浴室bath room⑳洗衣间laundry21 冷库freezing and refrigerating room22 储藏室storage (store ) room23 仓库store24 蓄电池间accumulator (battery ) room25 CO2间CO2 room26 发电机房generator room27 应急发电机房emergency generator room28 液压站hydraulic pump room29 泵房pump room (compartment)30 污水处理间sewage treatment compartment31 锅炉房boil er room32 配电间switchboard room33 淡水舱fresh water tank34 引用水舱portabl e water tank35 海水舱sea water tank36 泥浆舱（池）mud tank(pit)37 洗井液舱（池）38 压井液舱kill mud tank39 燃油舱fuel oil tank40 污水舱bilge tank41 污油舱dirty oil tank42 压载舱ballast tank (compartment)二、结构2.1一般述语1) 结构强度strength of structure2) 总纵强度overall l ongitudinal strength3) 整体强度overall strength4) 局部强度local strength5) 抗弯曲强度beading strength6) 抗剪强度shearing strength7) 抗扭强度twisting strength8) 抗压强度compressing strength9) 抗拉强度strength of extension10) 纵骨架式l ongitudinal framing system11) 横骨架式transverse framing system12) 混合骨架式combine framing system13) 桁架结构space truss structure14) 板梁结构plate-beam structure2.2主要构件2.2.1板plate1) 甲板d eck plate2) 甲板边板d eck stringer plate3) 船底板bottom plate4) 内底板inner bottom plate5) 平板龙骨ked flat plate6) 舷侧外板sid e plate7) 舷顶外板top sid e plate8) 船墙板bulwark plate9) 舱部板bilge plate10) 舱壁板bulkhead plate11) 船首外板bow plate12) 船尾板extern plate13) 支柱顶板cap plate14) 加强板d oubl e plate15) 花钢板checkered plate16) 三角眼板triangular eye plate2.2.2梁beam1) 简支梁beam with simply supported ends2) 固端梁beam with fixed ends3) 箱形梁box beam4) 组合梁built beam5) 强梁strong beam6) 纵梁l ongitudinal beam7) 悬臂梁cantil ever beam8) 横梁transverse beam9) 强横梁web beam10) 舱口横梁hatch-cress beam11) 桁架梁trussed beam2.2.3桁gird er1) 中底桁bottom center gird er2) 旁底桁bottom sid e gird er3) 中内龙骨keel gird er4) 舱内龙骨wing gird er5) 甲板纵桁d eck gird er6) 舱口纵桁hatch gird er7) 纵桁l ongitudinal gird er8) 横桁transverse gird er9) 强纵桁d eep gird er10) 箱形纵桁box gird er2.2.4肋板fl eer1) 单底肋板singl e-bottom fl eer2) 双底肋板d oubl e-bottom fl eer3) 舱壁肋板bulkhead fl eer4) 连续肋板continuous fl eer5) 间断肋板intercostals fl eer6) 油密肋板oil tight fl eer7) 水密肋板water tight fl eer8) 实肋板plate(solid) fl eer9) 厚实肋板heavy plate fl eer10) 轻型肋板lightered fl eer11) 开孔肋板spectacl e fl eer12) 加强肋板d eep fl eer13) 组合肋板assembl ed fl eer2.2.5扶强材stiffener1) 舱壁扶强材bulkhead stiffener2) 舱口扶强材hatch stiffener3) 水平扶强材horizontals stiffener4) 垂直扶强材vertical stiffener5) 纵向扶强材l ongitudinal stiffener6) 横向扶强材transverse stiffener7) 梁腹加强板web stiffener2.2.6舱壁bulkhead1) 住舱舱壁accommodation bulkhead2) 舱室舱壁cabin bulkhead3) 气密舱壁air-tight bulkhead4) 水密舱壁water-tight bulkhead5) 非水密舱壁non-watertight bulkhead6) 中纵舱壁centerline bulkhead7) 横纵舱壁athwart ship(cross) bulkhead8) 槽形舱壁corrugated bulkhead9) 连续舱壁continuous bulkhead10) 主舱壁main bulkhead11) 前部舱壁forward bulkhead12) 前端舱壁front bulkhead13) 后端舱壁after bulkhead14) 防火舱壁fire-proof(fire-resisting) bulkhead15) 深舱壁d eep bulkhead16) 深舱舱壁d eep tank bulkhead17) 双层舱壁d oubl e bulkhead2.2.7肘板bracket1) 折边肘板flanged bracket2) 无折边肘板plain(plate) bracket3) 肋骨肘板frame bracket4) 梁肘板beam bracket5) 角肘板angl e bracket6) 舱肘板bilge bracket7) 防倾肘板tripping bracket2.2.8其它1) 支柱pillar2) 立柱column3) 斜撑diagonal4) 锚架anchor。

船舶专业英文词汇船舶专业英语词汇（按照字母顺序排列）（一）a faired set of lines 经过光顺处理的一套型线a stereo pair of photographs 一对立体投影相片abaft 朝向船体abandonment cost 船舶废置成本费用accommodation 居住（舱室）accommodation ladder 舷梯adjust valve 调节阀adjustable-pitch 可调螺距式admiralty 海军部advance coefficient 进速系数aerostatic 空气静力学的aft peak bulkhead 艉尖舱壁aft peak tank 艉尖舱aileron 副鳍air cushion vehicle 气垫船air diffuser 空气扩散器air intake 进气口aircraft carrier 航空母舰air-driven water pump 气动水泵airfoil 气翼，翼剖面，机面，方向舵alignment chock 组装校准用垫楔aluminum alloy structure 铝合金结构American Bureau of Shipping 美国船级社amidships 舯amphibious 两栖的anchor arm 锚臂anchor chain 锚链anchor crown 锚冠anchor fluke 锚爪anchor mouth 锚唇anchor recess 锚穴anchor shackle 锚卸扣anchor stock 锚杆angle bar 角钢angle of attack 攻角angle plate 角钢angled deck 斜角甲板anticipated loads encountered at sea 在波浪中遭遇到的预期载荷anti-pitching fins 减纵摇鳍antiroll fins 减摇鳍anti-rolling tank 减摇水舱appendage 附体artisan 技工assembly line 装配流水线at-sea replenishment 海上补给augment of resistance 阻力增额auxiliary systems 辅机系统auxiliary tank 调节水舱axial advance 轴向进速backing structure 垫衬结构back-up member 焊接垫板balance weight 平衡锤ball bearing 滚珠轴承ball valve 球阀ballast tank 压载水舱bar 型材bar keel 棒龙骨，方龙骨，矩形龙骨barge 驳船baseline 基线basic design 基本设计batten 压条，板条beam 船宽，梁beam bracket 横梁肘板beam knee 横梁肘板bed-plate girder 基座纵桁bending-moment curves 弯矩曲线Benoulli’s law 伯努利定律berth term 停泊期bevel 折角bidder 投标人bilge 舭，舱底bilge bracket 舭肘板bilge radius 舭半径bilge sounding pipe 舭部边舱水深探管bitt 单柱系缆桩blade root 叶跟blade section 叶元剖面blast 喷丸block coefficient 方形系数blue peter 出航旗boarding deck 登艇甲板boat davit 吊艇架boat fall 吊艇索boat guy 稳艇索bobstay 首斜尾拉索body plan 横剖面图bolt 螺栓，上螺栓固定Bonjean curve 邦戎曲线boom 吊杆boss 螺旋桨轴榖bottom side girder 旁底桁bottom side tank 底边舱bottom transverse 底列板boundary layer 边界层bow line 前体纵剖线bow wave 艏波bowsprit 艏斜桅bow-thruster 艏侧推器box girder 箱桁bracket floor 框架肋板brake 制动装置brake band 制动带brake crank arm 制动曲柄brake drum 刹车卷筒brake hydraulic cylinder 制动液压缸brake hydraulic pipe 刹车液压管breadth extreme 最大宽，计算宽度breadth moulded 型宽breakbulk 件杂货breasthook 艏肘板bridge 桥楼，驾驶台bridge console stand 驾驶室集中操作台BSRA 英国船舶研究协会buckle 屈曲buffer spring 缓冲弹簧built-up plate section 组合型材bulb plate 球头扁钢bulbous bow 球状船艏，球鼻首bulk carrier 散货船bulk oil carrier 散装油轮bulkhead 舱壁bulwark 舷墙bulwark plate 舷墙板bulwark stay 舷墙支撑buoy tender 航标船buoyant 浮力的buoyant box 浮箱Bureau Veritas 法国船级社butt weld 对缝焊接butterfly screw cap 蝶形螺帽buttock 后体纵剖线by convention 按照惯例，按约定船舶专业英语词汇（按照字母顺序排列）（二）cable ship 布缆船cable winch 钢索绞车CAD(computer-aided design) 计算机辅助设计CAE(computer-aided manufacturing) 计算机辅助制造CAM(computer-aided engineering) 计算机辅助工程camber 梁拱cant beam 斜横梁cant frame 斜肋骨cantilever beam 悬臂梁capacity plan 舱容图CAPP(computer –aided process planning) 计算机辅助施工计划制定capsize 倾覆capsizing moment 倾覆力臂captain 船长captured-air-bubble vehicle 束缚气泡减阻船cargo cubic 货舱舱容，载货容积cargo handling 货物装卸carriage 拖车，拖架cast steel stem post 铸钢艏柱catamaran 高速双体船catamaran 双体的cavitation 空泡cavitation number 空泡数cavitation tunnel 空泡水筒center keelson 中内龙骨centerline bulkhead 中纵舱壁centroid 型心，重心，质心，矩心chain cable stopper 制链器chart 海图charterer 租船人chief engineer 轮机长chine 舭，舷，脊chock 导览钳CIM(computer integrated manufacturing) 计算机集成组合制造circulation theory 环流理论classification society 船级社cleat 系缆扣clipper bow 飞剪型船首clutch 离合器coastal cargo 沿海客货轮cofferdam 防撞舱壁combined cast and rolled stem 混合型艏柱commercial ship 营利用船commissary spaces 补给库舱室，粮食库common carrier 通用运输船commuter 交通船compartment 舱室compass 罗经concept design 概念设计connecting tank 连接水柜constant-pitch propeller 定螺距螺旋桨constraint condition 约束条件container 集装箱containerized 集装箱化contract design 合同设计contra-rotating propellers 对转桨controllable-pitch 可控螺距式corrosion 锈蚀，腐蚀couple 力矩，力偶crane 克令吊，起重机crank 曲柄crest (of wave) 波峰crew quarters 船员居住舱criterion 判据，准则Critical ath Method 关键路径法cross-channel automobile ferries 横越海峡车客渡轮cross-sectional area 横剖面面积crow’s nest 桅杆瞭望台cruiser stern 巡洋舰尾crussing range 航程cup and ball joint 球窝关节curvature 曲率curves of form 各船形曲线cushion of air 气垫damage stability 破损稳性damper 缓冲器damping 阻尼davit arm 吊臂deadweight 总载重量de-ballast 卸除压载deck line at side 甲板边线deck longitudinal 甲板纵骨deck stringer 甲板边板deck transverse 强横梁deckhouse 舱面室，甲板室deep v hull 深v型船体delivery 交船depth 船深derrick 起重机，吊杆design margin 设计余量design spiral 设计螺旋循环方式destroyer 驱逐舰detachable shackle 散合式连接卸扣detail design 详细设计diagonal stiffener 斜置加强筋diagram 图，原理图，设计图diesel engine 柴油机dimensionless ratio 无量纲比值displacement 排水量displacement type vessel 排水型船distributed load 分布载荷division 站，划分，分隔do work 做功dock 泊靠double hook 山字钩double iteration procedure 双重迭代法double roller chock 双滚轮式导览钳double-acting steam cylinder 双向作用的蒸汽气缸down halyard 降帆索draft 吃水drag 阻力，拖拽力drainage 排水draught 吃水，草图，设计图，牵引力dredge 挖泥船drift 漂移，偏航drilling rig 钻架drillship 钻井船drive shaft 驱动器轴driving gear box 传动齿轮箱driving shaft system 传动轴系dry dock 干船坞ducted propeller 导管螺旋桨dynamic supported craft 动力支撑型船舶dynamometer 测力计，功率计船舶专业英语词汇（按照字母顺序排列）（三）e.h.p 有效马力eccentric wheel 偏心轮echo-sounder 回声探深仪eddy 漩涡eddy-making resistance 漩涡阻力efficiency 供给能力，供给量electrohydraulic 电动液压的electroplater 电镀工elevations 高度，高程，船型线图的侧面图，立视图，纵剖线图，海拔empirical formula 经验公式enclosed fabrication shop 封闭式装配车间enclosed lifeboat 封闭式救生艇end open link 末端链环end shackle 末端卸扣endurance 续航力endurance 续航力，全功率工作时间engine room frame 机舱肋骨engine room hatch end beam 机舱口端梁ensign staff 船尾旗杆entrance 进流段erection 装配，安装exhaust valve 排气阀expanded bracket 延伸肘板expansion joint 伸缩接头extrapolate 外插fair 光顺faised floor 升高肋板fan 鼓风机fatigue 疲劳feasibility study 可行性研究feathering blade 顺流变距桨叶fender 护舷ferry 渡轮，渡运航线fillet weld connection 贴角焊连接fin angle feedback set 鳍角反馈装置fine fast ship 纤细高速船fine form 瘦长船型finite element 有限元fire tube boiler 水火管锅炉fixed-pitch 固定螺距式flange 突边，法兰盘flanking rudders 侧翼舵flap-type rudder 襟翼舵flare 外飘，外张flat of keel 平板龙骨fleets of vessels 船队flexural 挠曲的floating crane 起重船floodable length curve 可进长度曲线flow of materials 物流flow pattern 流型，流线谱flush deck vessel 平甲板型船flying bridge 游艇驾驶台flying jib 艏三角帆folding batch cover 折叠式舱口盖folding retractable fin stabilizer 折叠收放式减摇鳍following edge 随边following ship 后续船foot brake 脚踏刹车fore peak 艏尖舱forged steel stem 锻钢艏柱forging 锻件，锻造forward draft mark 船首水尺forward/afer perpendicular 艏艉柱forward/after shoulder 前/后肩foundry casting 翻砂铸造frame 船肋骨，框架，桁架freeboard 干舷freeboard deck 干舷甲板freight rate 运费率fresh water loadline 淡水载重线frictional resistance 摩擦阻力Froude number 傅汝德数fuel/water supply vessel 油水供给船full form 丰满船型full scale 全尺度fullness 丰满度funnel 烟囱furnishings 内装修gaff 纵帆斜桁gaff foresail 前桅主帆gangway 舷梯gantt chart 甘特图gasketed openings 装以密封垫的开口general arrangement 总布置general cargo ship 杂货船generatrix 母线geometrically similar form 外形相似船型girder 桁梁，桁架girder of foundation 基座纵桁governmental authorities 政府当局，管理机构gradient 梯度graving dock 槽式船坞Green Book 绿皮书，19世纪英国另一船级社的船名录，现合并与劳埃德船级社，用于登录快速远洋船gross ton 长吨（1.016公吨）group technology 成祖建造技术GT 成组建造技术guided-missile cruiser 导弹巡洋舰gunwale 船舷上缘gunwale angle 舷边角钢gunwale rounded thick strake 舷边圆弧厚板guyline 定位索gypsy 链轮gyro-pilot steering indicator 自动操舵操纵台gyroscope 回转仪船舶专业英语词汇（按照字母顺序排列）（四）half breadth plan 半宽图half depth girder 半深纵骨half rounded flat plate 半圆扁钢hard chine 尖舭hatch beam sockets 舱口梁座hatch coaming 舱口围板hatch cover 舱口盖hatch cover 舱口盖板hatch cover rack 舱口盖板隔架hatch side cantilever 舱口悬臂梁hawse pipe 锚链桶hawsehole 锚链孔heave 垂荡heel 横倾heel piece 艉柱根helicoidal 螺旋面的，螺旋状的hinge 铰链hinged stern door 艉部吊门HMS 英国皇家海军舰艇hog 中拱hold 船舱homogeneous cylinder 均质柱状体hopper barge 倾卸驳horizontal stiffener 水平扶强材hub 桨毂，轴毂，套筒hull form 船型，船体外形hull girder stress 船体桁应力HVAC(heating ventilating and cooling) 取暖，通风与冷却hydraulic mechanism 液压机构hydrodynamic 水动力学的hydrofoil 水翼hydrostatic 水静力的IAGG(interactive computer graphics) 交互式计算机图像技术icebreaker 破冰船icebreaker 破冰船IMCO(Intergovernmental Maritime Consultative Organization) 国际海事质询组织immerse 浸水，浸没impact load 冲击载荷imperial unit 英制单位in strake 内列板inboard profile 纵剖面图incremental plasticity 增量塑性independent tank 独立舱柜initial stability at small angle of inclination 小倾角初稳性inland waterways vessel 内河船inner bottom 内底in-plane load 面内载荷intact stability 完整稳性intercostals 肋间的，加强的International Association of Classification Society (IACS) 国际船级社联合会International Towing Tank Conference (ITTC) 国际船模试验水池会议intersection 交点，交*，横断（切）inventory control 存货管理iterative process 迭代过程jack 船首旗jack 千斤顶joinery 细木工keel 龙骨keel laying 开始船舶建造kenter shackle 双半式连接链环Kristen-Boeing propeller 正摆线推进器landing craft 登陆艇launch 发射，下水launch 汽艇launching equipmeng （向水中）投放设备LCC 大型原油轮leading edge 导缘，导边ledge 副梁材length overall 总长leveler 调平器，矫平机life saving appliance 救生设备lifebuoy 救生圈lifejacket 救生衣lift fan 升力风扇lift offsets 量取型值light load draft 空载吃水lightening hole 减轻孔light-ship 空船limbers board 舭部污水道顶板liner trade 定期班轮营运业lines 型线lines plan 型线图Linnean hierarchical taxonomy 林式等级式分类学liquefied gas carrier 液化气运输船liquefied natural gas carrier 液化天然气船liquefied petroleum gas carrier 液化石油气船liquid bulk cargo carrier 液体散货船liquid chemical tanker 液体化学品船list 倾斜living and utility spaces 居住与公用舱室Lloyd’s Register of shipping 劳埃德船级社Lloyd’s Rules 劳埃德规范Load Line Convention 载重线公约load line regulations 载重线公约，规范load waterplane 载重水线面loft floor 放样台longitudinal (transverse) 纵（横）稳心高longitudinal bending 纵总弯曲longitudinal prismatic coefficient 纵向菱形系数longitudinal strength 纵总强度longitudinally framed system 纵骨架式结构luffing winch 变幅绞车machinery vendor 机械（主机）卖方magnet gantry 磁力式龙门吊maiden voyage 处女航main impeller 主推叶轮main shafting 主轴系major ship 大型船舶maneuverability 操纵性manhole 人孔margin plate 边板maritime 海事的，海运的，靠海的mark disk of speed adjusting 速度调整标度盘mast 桅杆mast clutch 桅座matrix 矩阵merchant ship 商船Merchant Shipbuilding Return 商船建造统计表metacenter 稳心metacentric height 稳心高metal plate path 金属板电镀槽metal worker 金属工metric unit 公制单位middle line plane 中线面midship section 舯横剖面midship section coefficient 中横剖面系数ML 物资清单，物料表model tank 船模试验水池monitoring desk of main engine operation 主机操作监视台monitoring screen of screw working condition 螺旋桨运转监视屏more shape to the shell 船壳板的形状复杂mould loft 放样间multihull vessel 多体船multi-purpose carrier 多用途船multi-ship program 多种船型建造规划mushroom ventilator 蘑菇形通风桶mutually exclusive attribute 相互排它性的属性船舶专业英语词汇（按照字母顺序排列）（五）N/C 数值控制nautical mile 海里naval architecture 造船学navigation area 航区navigation deck 航海甲板near-universal gear 准万向舵机，准万向齿轮net-load curve 静载荷曲线neutral axis 中性轴，中和轴neutral equilibrium 中性平衡non-retractable fin stabilizer 不可收放式减摇鳍normal 法向的，正交的normal operating condition 常规运作状况nose cone 螺旋桨整流帽notch 开槽，开凹口oar 橹，桨oblique bitts 斜式双柱系缆桩ocean going ship 远洋船off-center loading 偏离中心的装载offsets 型值offshore drilling 离岸钻井offshore structure 离岸工程结构物oil filler 加油点oil skimmer 浮油回收船oil-rig 钻油架on-deck girder 甲板上桁架open water 敞水optimality criterion 最优性准则ore carrier 矿砂船orthogonal 矩形的orthogonal 正交的out strake 外列板outboard motor 舷外机outboard profile 侧视图outer jib 外首帆outfit 舾装outfitter 舾装工outrigger 舷外吊杆*头overall stability 总体稳性overhang 外悬paddle 桨paddle-wheel-propelled 明轮推进的Panama Canal 巴拿马运河panting arrangement 强胸结构，抗拍击结构panting beam 强胸横梁panting stringer 抗拍击纵材parallel middle body 平行中体partial bulkhead 局部舱壁payload 有效载荷perpendicular 柱，垂直的，正交的photogrammetry 投影照相测量法pile driving barge 打桩船pillar 支柱pin jig 限位胎架pintle 销，枢轴pipe fitter 管装工pipe laying barge 铺管驳船piston 活塞pitch 螺距pitch 纵摇plan views 设计图planning hull 滑行船体Plimsoll line 普林索尔载重线polar-exploration craft 极地考察船poop 尾楼port 左舷port call 沿途到港停靠positive righting moment 正扶正力矩power and lighting system 动力与照明系统precept 技术规则preliminary design 初步设计pressure coaming 阻力式舱口防水挡板principal dimensions 主尺度Program Evaluation and Review Technique 规划评估与复核法progressive flooding 累进进水project 探照灯propeller shaft bracket 尾轴架propeller type log 螺旋桨推进器测程仪PVC foamed plastic PVC泡沫塑料quadrant 舵柄quality assurance 质量保证quarter 居住区quarter pillar 舱内侧梁柱quartering sea 尾斜浪quasi-steady wave 准定长波quay 码头，停泊所quotation 报价单船舶专业英语词汇（按照字母顺序排列）（六）racking 倾斜，变形，船体扭转变形radiography X射线探伤rake 倾斜raked bow 前倾式船首raster 光栅refrigerated cargo ship 冷藏货物运输船Register （船舶）登录簿，船名录Registo Italiano Navade 意大利船级社regulating knob of fuel pressure 燃油压力调节钮reserve buoyancy 储备浮力residuary resistance 剩余阻力resultant 合力reverse frame 内底横骨Reynolds number 雷诺数right-handed propeller 右旋进桨righting arm 扶正力臂，恢复力臂rigid side walls 刚性侧壁rise of floor 底升riverine warfare vessel 内河舰艇rivet 铆接，铆钉roll 横摇roll-on/roll-off (Ro/Ro) 滚装rotary screw propeller 回转式螺旋推进器rounded gunwale 修圆的舷边rounded sheer strake 圆弧舷板rubber tile 橡皮瓦rudder 舵rudder bearing 舵承rudder blade 舵叶rudder control rod 操舵杆rudder gudgeon 舵钮rudder pintle 舵销rudder post 舵柱rudder spindle 舵轴rudder stock 舵杆rudder trunk 舵杆围井run 去流段sag 中垂salvage lifting vessel 救捞船scale 缩尺，尺度schedule coordination 生产规程协调schedule reviews 施工生产进度审核screen bulkhead 轻型舱壁Sea keeping performance 耐波性能sea spectra 海浪谱sea state 海况seakeeping 适航性seasickness 晕船seaworthness 适航性seaworthness 适航性section moulus 剖面模数sectiongs 剖面，横剖面self-induced 自身诱导的self-propulsion 自航semi-balanced rudder 半平衡舵semi-submersible drilling rig 半潜式钻井架shaft bossing 轴榖shaft bracket 轴支架shear 剪切，剪力shear buckling 剪切性屈曲shear curve 剪力曲线sheer 舷弧sheer aft 艉舷弧sheer drawing 剖面图sheer forward 艏舷弧sheer plane 纵剖面sheer profile 总剖线sheer profile 纵剖图shell plating 船壳板ship fitter 船舶装配工ship hydrodynamics 船舶水动力学shipway 船台shipyard 船厂shrouded screw 有套罩螺旋桨，导管螺旋桨side frame 舷边肋骨side keelson 旁内龙骨side plate 舷侧外板side stringer 甲板边板single-cylinder engine 单缸引擎sinkage 升沉six degrees of freedom 六自由度skin friction 表面摩擦力skirt （气垫船）围裙slamming 砰击sleeve 套管，套筒，套环slewing hydraulic motor 回转液压马达slice 一部分，薄片sloping shipway 有坡度船台sloping top plate of bottom side tank 底边舱斜顶板slopint bottom plate of topside tank 定边舱斜底板soft chine 圆舭sonar 声纳spade rudder 悬挂舵spectacle frame 眼睛型骨架speed-to-length ratio 速长比sponson deck 舷伸甲板springing 颤振stability 稳性stable equilibrium 稳定平衡starboard 右舷static equilibrium 静平衡steamer 汽轮船steering gear 操纵装置，舵机stem 船艏stem contour 艏柱型线stern 船艉stern barrel 尾拖网滚筒stern counter 尾突体stern ramp 尾滑道，尾跳板stern transom plate 尾封板stern wave 艉波stiffen 加劲，加强stiffener 扶强材，加劲杆straddle 跨立，外包式叶片strain 应变strake 船体列板streamline 流线streamlined casing 流线型套管strength curves 强度曲线strength deck 强力甲板stress concentration 应力集中structural instability 结构不稳定性strut 支柱，支撑构型subassembly 分部装配subdivision 分舱submerged nozzle 浸没式喷口submersible 潜期suction back of a blade 桨叶片抽吸叶背Suez Canal tonnage 苏伊士运河吨位限制summer load water line 夏季载重水线superintendent 监督管理人，总段长，车间主任superstructure 上层建筑Supervision of the Society’s surveyor 船级社验船师的监造书supper cavitating propeller 超空泡螺旋桨surface nozzle 水面式喷口surface piercing 穿透水面的surface preparation and coating 表面加工处理与喷涂surge 纵荡surmount 顶上覆盖，越过swage plate 压筋板swash bulkhead 止荡舱壁SWATH (Small Waterplane Area Twin Hull) 小水线面双体船sway 横荡船舶专业英语词汇（按照字母顺序排列）（七）tail-stabilizer anchor 尾翼式锚talking paper 讨论文件tangential 切向的，正切的tangential viscous force 切向粘性力tanker 油船tee T型构件，三通管tender 交通小艇tensile stress 拉（张）应力thermal effect 热效应throttle valve 节流阀throughput 物料流量thrust 推力thruster 推力器，助推器timber carrier 木材运输船tip of a blade 桨叶叶梢tip vortex 梢涡toed towards amidships 趾部朝向船舯tonnage 吨位torpedo 鱼雷torque 扭矩torque 扭矩trailing edge 随边transom stern 方尾transverse bulkhead plating 横隔舱壁板transverse section 横剖面transverse stability 横稳性trawling 拖网trial 实船试验trim 纵倾trim by the stern/bow 艉艏倾trimaran 三体的tripping bracket 防倾肘板trough 波谷tugboat 拖船tumble home （船侧）内倾tunnel wall effect 水桶壁面效应turnable blade 可转动式桨叶turnable shrouded screw 转动导管螺旋桨tweendeck cargo space 甲板间舱tweendedk frame 甲板间肋骨two nodded frequency 双节点频率ULCC 超级大型原油轮ultrasonic 超声波的underwriter （海运）保险商unsymmetrical 非对称的upright position 正浮位置vapor pocket 气化阱ventilation and air conditioning diagram 通风与空调铺设设计图Venturi section 文丘里试验段vertical prismatic coefficient 横剖面系数vertical-axis(cycloidal)propeller 直叶（摆线）推进器vessel component vender 造船部件销售商viscosity 粘性VLCC 巨型原油轮Voith-Schneider propeller 外摆线直翼式推进器v-section v型剖面wake current 伴流，尾流water jet 喷水（推进）管water plane 水线面watertight integrity 水密完整性wave pattern 波形wave suppressor 消波器，消波板wave-making resistance 兴波阻力weather deck 露天甲板web 腹板web beam 强横梁web frame 腹肋板welder 焊工wetted surface 湿表面积winch 绞车windlass 起锚机wing shaft 侧轴wing-keel 翅龙骨（游艇）working allowance 有效使用修正量worm gear 蜗轮，蜗杆yacht 快艇yard issue 船厂开工任务发布书yards 帆桁yaw 首摇。

IMO(Intergovernmental Maritime Organization)国际海事组织IMCO(Intergovernmental Maritime Consultative Organization)国际海事质询组织International Towing Tank Conference (ITTC) 国际船模试验水池会议International Association of Classification Society (IACS) 国际船级社协会ABS(American Bureau of Shipping) 美国船级社BV(Bureau Veritas) 法国船级社Lloyd's Register of shipping 英国劳埃德船级社RINA(Registo Italiano Navade) 意大利船级社Load Line Convention 载重线公约Lloyd's Rules 劳埃德规范Register （船舶）登录簿，船名录Green Book 绿皮书，19世纪英国另一船级社的船名录，现合并与劳埃德船级社，用于登录快速远洋船Supervision of the Society's surveyor 船级社验船师的监造书Merchant Shipbuilding Return 商船建造统计表BSRA 英国船舶研究协会HMS 英国皇家海军舰艇CAD(computer-aided design) 计算机辅助设计CAE(computer-aided manufacturing) 计算机辅助制造CAM(computer-aided engineering) 计算机辅助工程CAPP(computer -aided process planning) 计算机辅助施工计划制定IAGG(interactive computer graphics) 交互式计算机图像技术a faired set of lines 经过光顺处理的一套型线a stereo pair of photographs 一对立体投影相片abaft 朝向船体abandonment cost 船舶废置成本费用accommodation 居住（舱室）accommodation ladder 舷梯adjust valve 调节阀adjustable-pitch 可调螺距式admiralty 海军部advance coefficient 进速系数aerostatic 空气静力学的aft peak bulkhead 艉尖舱壁aft peak tank 艉尖舱aileron 副鳍air cushion vehicle 气垫船air diffuser 空气扩散器air intake 进气口aircraft carrier 航空母舰air-driven water pump 气动水泵airfoil 气翼，翼剖面，机面，方向舵alignment chock 组装校准用垫楔aluminum alloy structure 铝合金结构amidships 舯amphibious 两栖的anchor arm 锚臂anchor chain 锚链anchor crown 锚冠anchor fluke 锚爪anchor mouth 锚唇anchor recess锚穴anchor shackle 锚卸扣anchor stock 锚杆angle bar/plate 角钢angle of attack 攻角angled deck 斜角甲板anticipated loads encountered at sea 在波浪中遭遇到的预期载荷anti-pitching fins 减纵摇鳍antiroll fins 减摇鳍anti-rolling tank 减摇水舱appendage 附体artisan 技工assembly line 装配流水线at-sea replenishment 海上补给augment of resistance 阻力增额auxiliary systems 辅机系统auxiliary tank 调节水舱axial advance 轴向进速backing structure 垫衬结构back-up member 焊接垫板balance weight 平衡锤ball bearing 滚珠轴承ball valve 球阀ballast tank 压载水舱bar 型材bar keel 棒龙骨，方龙骨，矩形龙骨barge 驳船base line 基线basic design 基本设计batten 压条，板条beam 船宽，梁beam bracket 横梁肘板爱beam knee 横梁肘板bearing 轴承bed-plate girder 基座纵桁bending-moment curves 弯矩曲线Benoulli's law 伯努利定律berth term 停泊期bevel 折角bidder 投标人bilge 舭，舱底bilge bracket 舭肘板bilge radius 舭半径bilge sounding pipe 舭部边舱水深探管bitt 单柱系缆桩blade root 叶跟blade section 叶元剖面blast 喷丸block coefficient 方形系数blue peter 出航旗boarding deck 登艇甲板boat davit 吊艇架boat fall 吊艇索boat guy 稳艇索bobstay 首斜尾拉索body plan 横剖面图bolt 螺栓，上螺栓固定Bonjean curve 邦戎曲线boom 吊杆boss 螺旋桨轴榖bottom side girder 旁底桁bottom side tank 底边舱bottom transverse 底列板boundary layer 边界层bow line 前体纵剖线bow wave 艏波bowsprit 艏斜桅bow-thruster 艏侧推器box girder 箱桁bracket floor 框架肋板brake 制动装置brake band 制动带brake crank arm 制动曲柄brake drum 刹车卷筒brake hydraulic cylinder 制动液压缸brake hydraulic pipe 刹车液压管breadth extreme 最大宽，计算宽度breadth moulded 型宽breakbulk 件杂货breasthook 艏肘板bridge 桥楼，驾驶台bridge console stand 驾驶室集中操作台buckle 屈曲buffer spring 缓冲弹簧built-up plate section 组合型材bulb plate 球头扁钢bulbous bow 球状船艏，球鼻首bulk carrier 散货船bulk oil carrier 散装油轮bulkhead 舱壁bulwark 舷墙bulwark plate 舷墙板bulwark stay 舷墙支撑buoy tender 航标船buoyant 浮力的buoyant box 浮箱butt weld 对缝焊接butterfly screw cap 蝶形螺帽buttock 后体纵剖线by convention 按照惯例，按约定cable ship 布缆船cable winch 钢索绞车camber 梁拱cant beam 斜横梁cant frame 斜肋骨cantilever beam 悬臂梁capacity plan 舱容图capsize 倾覆capsizing moment 倾覆力臂captain 船长captured-air-bubble vehicle 束缚气泡减阻船cargo cubic 货舱舱容，载货容积cargo handling 货物装卸carriage 拖车，拖架cast steel stem post 铸钢艏柱catamaran 高速双体船，双体的cavitation 空泡cavitation number 空泡数cavitation tunnel 空泡水筒center keelson 中内龙骨centerline bulkhead 中纵舱壁centroid 型心，重心，质心，矩心chain cable stopper 制链器chart 海图charterer 租船人chief engineer 轮机长chine 舭，舷，脊chock 导览钳CIM(computer integrated manufacturing) 计算机集成组合制造circulation theory 环流理论classification society 船级社cleat 系缆扣clipper bow 飞剪型船首clutch 离合器coastal cargo 沿海客货轮cofferdam 防撞舱壁combined cast and rolled stem 混合型艏柱commercial ship 营利用船commissary spaces 补给库舱室，粮食库common carrier 通用运输船commuter 交通船compartment 舱室compass 罗经concept design 概念设计connecting tank 连接水柜constant-pitch propeller 定螺距螺旋桨constraint condition 约束条件container 集装箱containerized 集装箱化contract design 合同设计contra-rotating propellers 对转桨controllable-pitch 可控螺距式corrosion 锈蚀，腐蚀couple 力矩，力偶crane 克令吊，起重机crank 曲柄crest (of wave) 波峰crew quarters 船员居住舱criterion 判据，准则Critical Path Method 关键路径法cross-channel automobile ferries 横越海峡车客渡轮cross-sectional area 横剖面面积crow's nest 桅杆瞭望台cruiser stern 巡洋舰尾crussing range 航程cup and ball joint 球窝关节curvature 曲率curves of form 各船形曲线cushion of air 气垫damage stability 破损稳性damper 缓冲器damping 阻尼davit arm 吊臂deadweight 总载重量de-ballast 卸除压载deck line at side 甲板边线deck longitudinal 甲板纵骨deck stringer 甲板边板deck transverse 强横梁deckhouse 舱面室，甲板室deep v hull 深v型船体delivery 交船depth 船深derrick 起重机，吊杆design margin 设计余量)design spiral 设计螺旋循环方式destroyer 驱逐舰detachable shackle 散合式连接卸扣detail design 详细设计diagonal stiffener 斜置加强筋diagram 图，原理图，设计图diesel engine 柴油机dimensionless ratio 无量纲比值displacement 排水量displacement type vessel 排水型船distributed load 分布载荷division 站，划分，分隔do work 做功dock 泊靠double hook 山字钩double iteration procedure 双重迭代法double roller chock 双滚轮式导览钳double-acting steam cylinder 双向作用的蒸汽气缸down halyard 降帆索draft 吃水drag 阻力，拖拽力drainage 排水draught 吃水，草图，设计图，牵引力爱dredge 挖泥船drift 漂移，偏航drilling rig 钻架drill ship 钻井船drive shaft 驱动器轴driving gear box 传动齿轮箱driving shaft system 传动轴系dry dock 干船坞ducted propeller 导管螺旋桨dynamic supported craft 动力支撑型船舶dynamometer 测力计，功率计e.h.p 有效马力eccentric wheel 偏心轮echo-sounder 回声探深仪eddy 漩涡eddy-making resistance 漩涡阻力efficiency 供给能力，供给量electrohydraulic 电动液压的electroplater 电镀工elevations 高度，高程，船型线图的侧面图，立视图，纵剖线图，海拔empirical formula 经验公式enclosed fabrication shop 封闭式装配车间enclosed lifeboat 封闭式救生艇end open link 末端链环end shackle 末端卸扣endurance 续航力，全功率工作时间engine room frame 机舱肋骨engine room hatch end beam 机舱口端梁ensign staff 船尾旗杆entrance 进流段erection 装配，安装exhaust valve 排气阀expanded bracket 延伸肘板expansion joint 伸缩接头extrapolate 外插fair 光顺faised floor 升高肋板fan 鼓风机fatigue 疲劳feasibility study 可行性研究feathering blade 顺流变距桨叶fender 护舷ferry 渡轮，渡运航线fillet weld connection 贴角焊连接fin angle feedback set 鳍角反馈装置fine fast ship 纤细高速船fine form 瘦长船型finite element 有限元fire tube boiler 水火管锅炉fixed-pitch 固定螺距式flange 突边，法兰盘flanking rudders 侧翼舵flap-type rudder 襟翼舵flare 外飘，外张flat of keel 平板龙骨fleets of vessels 船队flexural 挠曲的floating crane 起重船floodable length curve 可进长度曲线flow of materials 物流flow pattern 流型，流线谱flush deck vessel 平甲板型船flying bridge 游艇驾驶台flying jib 艏三角帆folding batch cover 折叠式舱口盖folding retractable fin stabilizer 折叠收放式减摇鳍following edge 随边following ship 后续船foot brake 脚踏刹车fore peak 艏尖舱forged steel stem 锻钢艏柱forging 锻件，锻造forward draft mark 船首水尺forward/after perpendicular 艏/艉柱forward/after shoulder 前/后肩foundry casting 翻砂铸造frame 船肋骨，框架，桁架frame spacing 肋骨间距freeboard 干舷freeboard deck 干舷甲板freight rate 运费率fresh water loadline 淡水载重线frictional resistance 摩擦阻力Froude number 傅汝德数fuel/water supply vessel 油水供给船full form丰满船型full scale 全尺度fullness 丰满度funnel 烟囱furnishings 内装修gaff 纵帆斜桁爱gaff foresail 前桅主帆gangway 舷梯gantt chart 甘特图gasketed openings 装以密封垫的开口general arrangement 总布置general cargo ship 杂货船generatrix 母线geometrically similar form 外形相似船型girder 桁梁，桁架girder of foundation 基座纵桁governmental authorities 政府当局，管理机构gradient 梯度graving dock 槽式船坞gross ton 长吨（1.016公吨，short for GT）group technology 成组建造技术guided-missile cruiser 导弹巡洋舰gunwale 船舷上缘gunwale angle 舷边角钢gunwale rounded thick strake 舷边圆弧厚板guyline 定位索gypsy 链轮gyro-pilot steering indicator 自动操舵操纵台gyroscope 回转仪half breadth plan 半宽图half depth girder 半深纵骨half rounded flat plate 半圆扁钢hard chine 尖舭hatch beam sockets 舱口梁座hatch coaming 舱口围板hatch cover 舱口盖（板）hatch cover rack 舱口盖板隔架hatch side cantilever 舱口悬臂梁hawse pipe 锚链桶hawsehole 锚链孔heave 垂荡heel 横倾heel piece 艉柱根helicoidal 螺旋面的，螺旋状的hinge 铰链hinged stern door 艉部吊门hog 中拱hold 船舱homogeneous cylinder 均质柱状体hopper barge 倾卸驳horizontal stiffener 水平扶强材hub 桨毂，轴毂，套筒hull form 船型，船体外形hull girder stress 船体桁应力HV AC(heating ventilating and cooling) 取暖，通风与冷却hydraulic mechanism 液压机构hydrodynamic 水动力学的hydrofoil 水翼hydrostatic 水静力的icebreaker 破冰船immerse 浸水，浸没impact load 冲击载荷imperial unit 英制单位in strake 内列板inboard profile 纵剖面图incremental plasticity 增量塑性independent tank 独立舱柜initial stability at small angle of inclination 小倾角初稳性inland waterways vessel 内河船inner bottom 内底in-plane load 面内载荷intact stability 完整稳性intercostals 肋间的，加强的intersection 交点，交叉，横断（切）inventory control 存货管理iterative process 迭代过程jack 船首旗jack 千斤顶joinery 细木工keel 龙骨keel laying 开始船舶建造kenter shackle 双半式连接链环Kristen-Boeing propeller 正摆线推进器landing craft 登陆艇launch 发射，下水launch 汽艇launching equipment （向水中）投放设备leading edge 导缘，导边ledge 副梁材length overall 总长leveler 调平器，矫平机life saving appliance 救生设备lifebuoy 救生圈lifejacket 救生衣lift fan 升力风扇lift offsets 量取型值light load draft 空载吃水lightening hole 减轻孔light-ship 空船limbers board 舭部污水道顶板liner trade 定期班轮营运业lines 型线lines plan 型线图Linnean hierarchical taxonomy 林式等级式分类学liquefied gas carrier 液化气运输船liquefied natural gas carrier 液化天然气船liquefied petroleum gas carrier 液化石油气船liquid bulk cargo carrier 液体散货船liquid chemical tanker 液体化学品船living and utility spaces 居住与公用舱室load line regulations 载重线公约，规范load waterplane 载重水线面loft floor 放样台longitudinal (transverse) 纵（横）稳心高longitudinal bending 纵总弯曲longitudinal prismatic coefficient 纵向棱形系数longitudinal strength 总纵强度longitudinally framed system 纵骨架式结构luffing winch 变幅绞车machinery vendor 机械（主机）卖方magnet gantry 磁力式龙门maiden voyage 处女航main impeller 主推叶轮main shafting 主轴系major ship 大型船舶maneuverability 操纵性manhole 人孔margin plate 边板mark disk of speed adjusting 速度调整标度盘mast 桅杆mast clutch 桅座matrix 矩阵merchant ship 商船metacenter 稳心metacentric height 稳心高metal plate path 金属板电镀槽metal worker 金属工metric unit 公制单位middle line plane 中线面midship section 舯横剖面midship section coefficient 中横剖面系数ML 物资清单，物料表model tank 船模试验水池monitoring desk of main engine operation 主机操作监视台monitoring screen of screw working condition 螺旋桨运转监视屏more shape to the shell 船壳板的形状复杂mould loft 放样间multihull vessel 多体船multi-purpose carrier 多用途船multi-ship program 多种船型建造规划mushroom ventilator 蘑菇形通风桶mutually exclusive attribute 相互排它性的属性N/C 数值控制nautical mile 海里naval architecture 造船学navigation area 航区navigation deck 航海甲板near-universal gear 准万向舵机，准万向齿轮net-load curve 静载荷曲线neutral axis 中性轴，中和轴neutral equilibrium 中性平衡non-retractable fin stabilizer 不可收放式减摇鳍normal 法向的，正交的normal operating condition 常规运作状况nose cone 螺旋桨整流帽notch 开槽，开凹口oar 橹，桨oblique bitts 斜式双柱系缆桩ocean going ship 远洋船off-center loading 偏离中心的装载offsets 型值offshore drilling 离岸钻井offshore structure 离岸工程结构物oil filler 加油点oil skimmer 浮油回收船oil-rig 钻油架on-deck girder 甲板上桁架open water 敞水optimality criterion 最优性准则ore carrier 矿砂船orthogonal 矩形的orthogonal 正交的out strake 外列板outboard motor 舷外机outboard profile 侧视图outer jib 外首帆outfit 舾装outfitter 舾装工outrigger 舷外吊杆叉头overall stability 总体稳性overhang 外悬paddle 桨paddle-wheel-propelled 明轮推进的Panama Canal 巴拿马运河panting arrangement 强胸结构，抗拍击结构panting beam 强胸横梁panting stringer 抗拍击纵材parallel middle body 平行中体partial bulkhead 局部舱壁payload 有效载荷perpendicular 柱，垂直的，正交的photogrammetry 投影照相测量法pile driving barge 打桩船pillar 支柱pin jig 限位胎架pintle 销，枢轴pipe fitter 管装工pipe laying barge 铺管驳船piston 活塞pitch 螺距ipitch 纵摇plan views 设计图planning hull 滑行船体Plimsoll line 普林索尔载重线polar-exploration craft 极地考察船poop 尾楼port 左舷port call 沿途到港停靠positive righting moment 正扶正力矩power and lighting system 动力与照明系统precept 技术规则preliminary design 初步设计pressure coaming 阻力式舱口防水挡板principal dimensions 主尺度Program Evaluation and Review Technique 规划评估与复核法progressive flooding 累进进水project 探照灯propeller shaft bracket 尾轴架爱propeller type log 螺旋桨推进器测程仪PVC foamed plastic PVC泡沫塑料quadrant 舵柄quality assurance 质量保证quarter 居住区quarter pillar 舱内侧梁柱quartering sea 尾斜浪quasi-steady wave 准定长波quay 码头，停泊所quotation 报价单racking 倾斜，变形，船体扭转变形radiography X射线探伤rake 倾斜raked bow 前倾式船首raster 光栅refrigerated cargo ship 冷藏货物运输船regulating knob of fuel pressure 燃油压力调节钮reserve buoyancy 储备浮力residuary resistance 剩余阻力resultant 合力reverse frame 内底横骨Reynolds number 雷诺数right-handed propeller 右旋进桨righting arm 扶正力臂，恢复力臂rigid side walls 刚性侧壁rise of floor 底升riverine warfare vessel 内河舰艇rivet 铆接，铆钉roll 横摇roll-on/roll-off (Ro/Ro) 滚装rotary screw propeller 回转式螺旋推进器9 rounded gunwale 修圆的舷边rounded sheer strake 圆弧舷板rubber tile 橡皮瓦rudder 舵rudder bearing 舵承rudder blade 舵叶rudder control rod 操舵杆rudder gudgeon 舵钮rudder horn 挂舵臂rudder pintle 舵销rudder post 舵柱rudder spindle 舵轴rudder stock 舵杆rudder trunk 舵杆围井run 去流段sag 中垂salvage lifting vessel 救捞船scale 缩尺，尺度schedule coordination 生产规程协调schedule reviews 施工生产进度审核screen bulkhead 轻型舱壁Sea keeping performance 耐波性能sea spectra 海浪谱sea state 海况seakeeping 适航性seasickness 晕船seaworthness 适航性seaworthness 适航性section moulus 剖面模数section 剖面，横剖面self-induced 自身诱导的self-propulsion 自航semi-balanced rudder 半平衡舵semi-submersible drilling rig 半潜式钻井架shaft bossing 轴榖shaft bracket 轴支架shaft coupling 联轴节shear 剪切，剪力shear buckling 剪切性屈曲shear curve 剪力曲线sheer 舷弧sheer aft/forward 艉/艏舷弧sheer drawing 剖面图sheer plane 纵剖面sheer profile 总剖线，纵剖图shell plating 船壳板ship fitter 船舶装配工ship hydrodynamics 船舶水动力学shipway/slipway 船台shipyard 船厂shrouded screw 有套罩螺旋桨，导管螺旋桨side frame 舷边肋骨side keelson 旁内龙骨side plate 舷侧外板side stringer 甲板边板single-cylinder engine 单缸引擎sinkage 升沉six degrees of freedom 六自由度skin friction 表面摩擦力skirt （气垫船）围裙slamming 砰击sleeve 套管，套筒，套环slewing hydraulic motor 回转液压马达slice 一部分，薄片sloping shipway 有坡度船台sloping top plate of bottom side tank 底边舱斜顶板sloping bottom plate of topside tank 顶边舱斜底板soft chine 圆舭sonar 声纳spade rudder 悬挂舵spectacle frame 眼睛型骨架speed-to-length ratio 速长比sponson deck 舷伸甲板springing 颤振stability 稳性stable equilibrium 稳定平衡starboard 右舷static equilibrium 静平衡steamer 汽轮船steering gear 操纵装置，舵机stem 船艏stem contour 艏柱型线stern 船艉stern barrel 尾拖网滚筒stern counter 尾突体stern ramp 尾滑道，尾跳板爱stern transom plate 尾封板stern wave 艉波stiffen 加劲，加强stiffener 扶强材，加劲杆straddle 跨立，外包式叶片strain 应变strake 船体列板streamline 流线streamlined casing 流线型套管strength curves 强度曲线strength deck 强力甲板stress concentration 应力集中structural instability 结构不稳定性strut 支柱，支撑构型subassembly 分部装配subdivision 分舱submerged nozzle 浸没式喷口submersible 潜期suction back of a blade 桨叶片抽吸叶背Suez Canal tonnage 苏伊士运河吨位限制summer load water line 夏季载重水线superintendent 监督管理人，总段长，车间主任superstructure 上层建筑supper cavitating propeller 超空泡螺旋桨surface nozzle 水面式喷口surface piercing 穿透水面的surface preparation and coating 表面预处理与喷涂surge 纵荡sway 横荡yaw 首摇surmount 顶上覆盖，越过swage plate 压筋板swash bulkhead 止荡舱壁SWATH (Small Waterplane Area Twin Hull) 小水线面双体船tail-stabilizer anchor 尾翼式锚talking paper 讨论文件tangential 切向的，正切的tangential viscous force 切向粘性力tanker 油船tender 交通小艇timber carrier 木材运输船tugboat 拖船tee T型构件，三通管tensile stress 拉（张）应力thermal effect 热效应throttle valve 节流阀throughput 物料流量thrust 推力thruster 推力器，助推器tip of a blade 桨叶叶梢toed towards amidships 趾部朝向船舯tonnage 吨位torpedo 鱼雷torque 扭矩trailing edge 随边transom stern 方尾transverse bulkhead plating 横隔舱壁板transverse section 横剖面transverse stability 横稳性trawling 拖网trial 实船试验trim 纵倾trim by the stern/bow 艉/艏倾trimaran 三体的tripping bracket 防倾肘板trough 波谷tumble home （船侧）内倾tunnel wall effect 水桶壁面效应turnable blade 可转动式桨叶turnable shrouded screw 转动导管螺旋桨tweendeck cargo space 甲板间舱tweendedk frame 甲板间肋骨two nodded frequency 双节点频率LCC 大型原油轮ULCC 超级大型原油轮VLCC 巨型原油轮ultrasonic 超声波的underwriter （海运）保险商unsymmetrical 非对称的upright position 正浮位置vapor pocket 气化阱ventilation and air conditioning diagram 通风与空调铺设设计图Venturi section 文丘里试验段vertical prismatic coefficient 横剖面系数vertical-axis(cycloidal)propeller 直叶（摆线）推进器vessel component vender 造船部件销售商viscosity 粘性V oith-Schneider propeller 外摆线直翼式推进器vortex 梢涡v-section v型剖面wake current 伴流，尾流water jet 喷水（推进）管water plane 水线面watertight integrity 水密完整性wave pattern 波形wave suppressor 消波器，消波板wave-making resistance 兴波阻力weather deck 露天甲板web 腹板web beam 强横梁web frame 腹肋板welder 焊工wetted surface 湿表面积winch 绞车windlass 起锚机wing shaft 侧轴wing-keel 翅龙骨（游艇）working allowance 有效使用修正量worm gear 蜗轮，蜗杆yacht 快艇yard issue 船厂开工任务发布书yards 帆桁--。

IMO(Intergovernmental Maritime Organization) 国际海事组织 IMCO(Intergovernmental Maritime Consultative Organization) 国际海事质询组织 International Towing Tank Conference (ITTC) 国际船模试验水池会 议 International Association of Classification Society (IACS) 国际船级社协会 ABS(American Bureau of Shipping) 美国船级社 BV(Bureau Veritas)法国船级社 Lloyd's Register of shipping英国劳埃德船级社 RINA(Registo Italiano Navade) 意大利船级社 Load Line Convention 载重线公约Lloyd's Rules劳埃德规范 Register (船舶)登录簿，船 名录 Green Book 绿皮书， 19 世纪英国 另一船级社的船名录，现合并与 劳埃德船级社，用于 登录快速远洋船Supervision of the Society's surveyor Merchant Shipbuilding Return BSRA 英国船舶研究协会 HMS 英国皇家海军舰艇aft peak bulkhead 艉尖舱壁 aft peak tank 艉尖舱aileron 副鳍air cushion vehicle 气垫船 air diffuser 空气扩散器 进air intakeair-driven waterpump 气动水泵 airfoil 气翼，翼剖面，机面 ，方向舵船级社验船师的监造 书商船建造统计表CAD(computer-aided design) 计算机辅助设计 计算机CAE(computer-aided manufacturing) CAM(computer-aided engineering) CAPP(computer -aided process planning) 辅助制造 计算机辅助工程计算机辅助施工计划制定 IAGG(interactive computer graphics) 交互式计算机图像技 术a faired setof lines 经过光顺处理的一套 型线a stereo pair of photographs 对立体投影相片abaft 朝向船体abandonment cost accommodation accommodation ladder 船舶废置成本费用居住（舱室）舷梯adjust valve adjustable-pitch admiralty advance coefficient aerostatic 调节阀可调螺距式海军部进速系数空气静力学的气口 aircraft carrier 航空母舰alignment chock aluminum alloy structure amidships amphibious anchorarm 组装校准用垫楔铝合金结构anchor chain anchor crown anchor fluke anchor mouth 舯两栖的锚臂锚链锚冠锚爪锚唇an chor recess 锚穴anchorshackle anchor stock锚卸扣锚杆角钢攻角斜角甲板angle bar/plate angle of attackangleddeck anticipated loadsencountered at sea anti-pitchingfins antiroll fins 在波浪中遭遇到的预期载荷anti-rolling tank appendage artisan assemblyline at-seareplenishment augment of resistance auxiliary systems auxiliary tank axial advance减纵摇鳍减摇鳍减摇水舱附体技工backing structure back-up member balanceweightball bearing ball valve ballast tank 装配流水线海上补给阻力增额辅机系统调节水舱轴向进速垫衬结构焊接垫板平衡锤滚珠轴承球阀压载水舱bar 型材bar keel bargebaselinebasic design battenbeambeam bracket beam knee bearing 轴承bed-plate girder棒龙骨，方龙骨，矩形龙骨驳船基线基本设计压条，板条船宽，梁横梁肘板爱横梁肘板基座纵桁bending-moment curves弯矩曲线 Benoulli's law 伯努利定律 berth term 停泊期 bevel 折角bidder 投标人bilge舭，舱底 bilge bracket 舭肘板 bilge radius舭半径 bilge sounding pipe 舭部边舱水深探管bitt 单柱系缆桩 blade root 叶跟 blade section叶元剖面 blast 喷丸brake hydraulic cylinder 制动液压缸 brake hydraulic pipe 刹车液压管 breadth extreme 最大宽，计算宽度 breadth moulded 型宽breakbulk 件杂货block coefficient方形系数 blue peterboarding deckboat davit boat fall boat guy bobstaybody plan bolt Bonjean curve boom boss bottom side girderbottom side tankbottom transverseboundary layerbow line bowwave bowspritbow-thrusterbox girderbracket floorbrake brakeband出航旗 登艇甲板 吊艇架 吊艇索 稳艇索 首斜尾拉索 横剖面图 螺栓，上螺栓固定 邦戎曲线 吊杆 螺旋桨轴榖旁底桁底边舱底列板边界层 前体纵剖线艏波 艏斜桅 艏侧推器 箱桁 框架肋板 制动装置 制动带brake crank armbrake drum 制动曲柄 刹车卷筒breasthook 艏肘板桥bridge楼，驾驶台bridge console stand 驾驶室集中操作台buckle 屈曲buffer spring 缓冲弹簧built-up plate section 组合型材bulb plate 球头扁钢bulbous bow 球状船艏，球鼻首bulk carrier 散货船bulk oil carrier 散装油轮bulkhead 舱壁bulwark 舷墙bulwark plate 舷墙板bulwark stay 舷墙支撑buoy tender航标船buoyant浮力的buoyant box 浮箱butt weld 对缝焊接butterfly screw cap 蝶形螺帽buttock 后体纵剖线by convention 按照惯例，按约定cable ship布缆船cable winch 钢索绞车camber 梁拱cant beam 斜横梁cant frame 斜肋骨cantilever beam 悬臂梁capacity plan 舱容图capsize 倾覆capsizing moment 倾覆力臂captain 船长captured-air-bubble vehicle 束缚气泡减阻船cargo cubic 货舱舱容，载货容积cargo handling货物装卸carriage 拖车，拖架cast steel stem post 铸钢艏柱高catamaran速双体船，双体的空cavitation 泡cavitation number 空泡数cavitation tunnel空泡水筒.r». [, 、ecenter keelson 中内龙骨centerline bulkhead 中纵舱壁centroid 型心，重心，质心，矩心chain cable stopper 制链器海图 charterer 租船人 chief engineer 轮机长 chine 舭，舷，脊 导 chock 览钳CIM(computer integrated manufacturing) circulation theory 环流理论 classification society 船级社 cleat 系缆扣 飞剪型船首 离合器沿海客货轮 防撞舱壁 chart clipper bow clutch coastal cargo cofferdamcombined cast and rolled stem混合型艏柱 营利用船 补给库舱室，粮食库 通用运输船 交通船 舱室 罗经 概念设计 连接水柜 定螺距螺旋桨 约束条件 commercial ship commissary spaces common carrier commutercompartment compass concept designconnecting tank constant-pitch propeller constraint condition 集装箱 1=1 集装箱化 合同设计 对转桨 可控螺距式 container containerized contract design contra-rotating propellerscontrollable-pitchcorrosion couplecrane crank crest(of wave) crew quarters criterion 锈蚀，腐蚀 力矩， 令吊， 曲柄 力偶 克 起重机 Critical Path Method 计算机集成组合制造波峰 船 员居住舱 判据，准则 关键路径法 cross-channel automobile ferries 横越海峡车客渡轮 cross-sectional area 横剖面面积 桅杆瞭望台 巡洋 舰尾 航程 球窝关节 曲率 crow's nest cruiser stern crussing range cup and balljoint curvaturecurves of form 各船形曲线cushion of air 气垫deepv hull v 型船体delivery 交船depth 船深derrick 起重机，吊杆design margin 设计余量) 设计螺design spiral 旋循环方式destroyer 驱逐舰displacement type vessel 排水型船distributed load 分布载荷division站，划分，分隔do work 做功dock 泊靠double hook 山字钩double iteration proceduredouble roller chockdouble-acting steam cylinder 双向作用的蒸汽气缸down halyard 降帆索draft drag drainage draught dredge drift drilling rig 吃水阻力，拖拽力排水吃水，草图，设计图，牵引力爱挖泥船漂移，偏航钻架damage stability 破损稳性damper damping davit arm deadweight de-ballast deck line at side 缓冲器阻尼吊臂总载重量卸除压载甲板边线deck longitudinal 甲板纵骨deck stringer deck transverse deckhouse甲板边板强横梁舱面室，甲板室深detachable shackle detail design diagonal stiffener diagram 图，diesel engine dimensionless ratio散合式连接卸扣详细设计斜置加强筋原理图，设计图柴油机无量纲比值displacement 排水量双重迭代法双滚轮式导览钳drill ship 钻井船 drive shaft 驱动器轴 传动driving gear box 齿轮箱driving shaft system 传动轴系 dry dock 干船坞 ducted propeller 导管螺旋桨 dynamic supported craft 动力支撑型船舶dynamometer 测力计，功率计e.h.p 有效马力 eccentric wheel echo-sounder eddy 漩涡 eddy-making resistance efficiencyelectrohydraulic electroplater elevations empirical formula enclosed fabrication enclosed lifeboat 偏心轮 回声探深仪漩涡阻力 供给能力，供给量电动液压的电镀工高度，高程，船型线 图的侧面图，立视图，纵剖线图，海拔经验公式封闭式装配车间 封闭式救生艇 shop end open link end shackle endurance engine room frame engine room hatch end beam ensign staff entrance 末端链环末端卸扣 续航力，全功率工作 时间 机舱肋骨 机舱口端梁 erection exhaust valve expanded bracket expansion joint extrapolate fair faised floor fan fatigue feasibility 船尾旗杆进流段装配，安装排气阀延伸肘板伸缩接头外插光顺升高肋板鼓风机疲劳可行性研究顺流变距桨叶 study feathering blade fender 护舷 ferry 渡轮，渡运航线 fillet weld connection 贴角焊连接 鳍fin angle feedback set 角反馈装置fine fast ship 纤细高速船fine form 瘦长船型finite element 有限元水fire tube boiler 火管锅炉fixed-pitch 固定螺距式flange突边，法兰盘flanking rudders 侧翼舵flap-type rudder 襟翼舵flare 外飘，外张平flat of keel板龙骨fleets of vessels 船队flexural 挠曲的floating crane 起重船floodable length curve 可进长度曲线flow of materials 物流flow pattern 流型，流线谱flush deck vessel 平甲板型船flying bridge游艇驾驶台flying jib艏三角帆folding batch cover 折叠式舱口盖folding retractable fin stabilizer 折叠收放式减摇鳍following edge 随边following ship 后续船foot brake 脚踏刹车fore peak 艏尖舱forged steelstem锻钢艏柱forging锻件，锻造forward draft mark 船首水尺forward/after perpendicular 艏/艉柱forward/after shoulder 前/后肩foundry casting翻砂铸造船frame肋骨，框架，桁架frame spacing 肋骨间距freeboard 干舷freeboard deck 干舷甲板freight rate 运费率fresh water loadline 淡水载重线frictional resistance 摩擦阻力Froude number 傅汝德数fuel/water supply vessel 油水供给船full form 丰满船型full scale 全尺度fullness 丰满度funnel 烟囱furnishings内装修gaff 纵帆斜桁爱gaff foresail 前桅主帆 gangway 舷梯 gantt chart 甘特图 gasketed openings装以密封垫的开口 general arrangement总布置 general cargo ship杂货船generatrix 母线 geometrically similar form 外形相似船型 girder 桁梁，桁架girder of foundation 基座纵桁governmental authorities 政府当局，管理机构 gradient梯度graving dock槽式船坞 gross ton 长吨（ 1.016 公吨， short for GT ）group technology成组建造技术 guided-missile cruiser 导弹巡洋舰 gunwale 船舷上缘 gunwale angle 舷边角钢gunwale rounded thick strake guyline定位索 gypsy 链轮gyro-pilot steering indicator gyroscope回转仪 half breadth plan半宽图 half depth girder 半深纵骨 half rounded flat plate 半圆扁钢 hard chine尖舭 hatch beam sockets hatch coaming hatch cover hatch cover rack hatch side cantilever hawse pipe hawsehole heave垂荡 heel 横倾 heel piece艉柱根helicoidal螺旋面的，螺旋状的 hinge 铰链 hinged stern door 艉部吊门hog中拱 hold 船舱舷边圆弧厚板 自动操舵操纵台舱口梁座 舱口围板 舱口盖（板） 舱口盖板隔架 舱口悬臂梁 锚链桶 锚链孔homogeneous cylinder 均质柱状体导缘，导边 副梁材总长 调平器，矫平机life saving appliance救生设备 lifebuoy 救生圈lifejacket 救生衣horizontal stiffener 水平扶强材 hub 桨毂，轴毂，套筒 船 hull form 型，船体外形hull girder stress 船体桁应力HVAC(heating ventilating and cooling)hydraulic mechanism液压机构 hydrodynamic 水动力学的 hydrofoil 水翼 hydrostatic水静力的 icebreaker破冰船 浸 immerse水，浸没 impact load冲击载荷 imperial unit英制单位 in strake 内列板 inboard profile 纵剖面图 incremental plasticity增量塑性 independent tank 独立舱柜取暖，通风与冷却 initial stability at small angle of inclination 小倾角初稳性 in-plane load面内载荷 intactstability 完整稳性 intercostals肋间的，加强的 intersection 交点，交叉，横断inventory control 存货管理iterative process 迭代过程jack船首旗jack千斤顶 joinery细木工 keel 、Prl 龙骨keel laying kenter shackle Kristen-Boeing landing craft launch launch propeller 登陆艇发射，下水 汽艇正摆线推进器launching equipment 向水中）投放设备leading edge ledge length overall leveler inland waterways vessel 内河船 innerbottom 内底开始船舶建造 双 半式连接链环切）升力风扇 量取型值 空载吃水 减轻孔空船 舭部污水道顶板 定期班轮营运业林式等级式分类学液化气运输船 液化天然气船 液 化石油气船液体散货船 液体化学品船居住与公用舱室 载重线公约，规范 载重水线面（transverse ）纵（横）稳心高bending纵总弯曲prismatic coefficient 纵向棱形系数 strength总纵强度framed system纵骨架式结构变幅绞车 机械（主机）卖方 磁力式龙门处女航 主推叶轮 主轴系 大型船舶 操纵性 人孔边板mark disk of speed adjusting 速度调整标度盘 mast桅杆mast clutch桅座matrix矩阵merchant ship商船metacenter 稳心metacentric height 稳心高 金metal plate path属板电镀槽metal worker 金属工metric unit 公制单位lift fan lift offsets light load draft lightening hole light-shiplimbers board liner trade lines lines planLinnean hierarchical taxonomy liquefied gas carrierliquefied natural gas carrier liquefied petroleum gascarrier liquid liquid living 型线 型线图 bulk cargo carrier chemical tanker and utility spaces放样台 load line regulations load waterplane loft floor longitudinal longitudinal longitudinal longitudinal longitudinally luffing winch machinery vendor magnet gantry maiden voyage main impeller main shafting major shipmaneuverability manhole margin platemiddle line plane 中线面midship section 舯横剖面midship section coefficient 中横剖面系数ML物资清单，物料表model tank 船模试验水池monitoring desk of main engine operation 主机操作监视台monitoring screen of screw working condition 桨运转监视屏more shapeto the shell 船壳板的形状复杂mould loft 放样间oil filler 加油点oil skimmer 浮油回收船oil-rig 钻油架on-deck girder 甲板上桁架open water optimality criterion ore carrier orthogonal orthogonal 敞水最优性准则矿砂船矩形的正交的螺旋multihull vessel multi-purpose carrier multi-ship program mushroom 多体船多用途船多种船型建造规划蘑菇形通风桶mutually exclusive attribute 相互排它性的属性N/C数值控制nautical mile naval architecture navigation area navigation deck near-universal gear net-load curve neutral axisneutral equilibrium海里造船学航区航海甲板准万向舵机，准万向静载荷曲线中性轴，中和轴中性平衡non-retractable fin stabilizer 不可收放式减摇鳍normal 法向的，正交的normal operating condition 常规运作状况nose cone 螺旋桨整流帽notch 开槽，桨oar 桨oblique bitts ocean going ship off-center loading 开凹口橹，斜式双柱系缆桩远洋船偏离中心的装载offsets 型值offshoredrilling offshore structure 离岸钻井离岸工程结构物舾装工 舷外吊杆叉头 总体稳性 外悬 桨paddle-wheel-propelled 明轮推进的PanamaCanal巴拿马运河强胸结构，抗拍击结强胸横梁 抗拍击纵材平行中体 局部舱壁payload 有效载荷perpendicular 柱，垂直的，正交的photogrammetry投 影 照 相 测 量 法pile driving pillar pin jig支柱 限位胎架pintle 销，枢轴 pipe fitter 管装工pipe laying barge 铺管驳船piston 活塞pitch 螺距ipitch 纵摇plan views 设计图planning hull 滑行船体 普林Plimsoll line索尔载重线polar-exploration craft poop 尾楼 port左舷port call沿途到港停靠Program Evaluation and Review Technique progressive flooding 累进进水out strake outboard motor outboard profile outer jib outfit 外列板舷外机 侧视图外首帆舾装outfitter outrigger overall stabilityoverhang paddlepanting arrangement panting beam panting stringer parallelmiddle body partial bulkheadbarge打桩船极地考察船positive righting moment power and lighting system precept 技术规则preliminary design pressure coaming principaldimensions正扶正力矩 力与照明系统初步设计 阻力式舱口防水挡板 主尺度规划评估与复核法quay 码头，停泊所 quotation 报价单racking 倾斜，变形，船体扭 转变形radiography X 射线探伤 rake 倾斜raked bow前倾式船首raster光栅refrigerated cargo ship 冷藏货物运输船 regulating knob of fuel pressure 力调节钮reserve buoyancy 储备浮力residuary resistance剩余阻力resultant 合力 reverse frame 内底横骨Reynolds number雷诺数right-handed propeller右旋进桨 扶righting arm 正力臂，恢复力臂rigid side walls 刚性侧壁rise of floor 底升riverine warfare vessel内河舰艇rivet 铆接，铆钉rubber tile rudder 舵 rudder bearing rudder blade rudder control rod rudder gudgeon rudder horn挂舵臂 rudderpintle rudder postproject 探照灯 propeller shaft bracket propeller type log尾轴架爱 螺旋 桨推进器测程仪PVC foamed plastic quadrant 舵柄qualityassurance PVC 泡沫塑料质量保证quarter quarter pillar quartering sea 居住区 舱内侧梁柱 尾斜浪quasi-steady wave 准定长波燃油压 roll 横摇roll-on/roll-off(Ro/Ro) rotary screw propeller rounded gunwale rounded sheer strake 滚装回转式螺旋推进器 修圆的舷边圆弧舷板橡皮瓦舵承 舵叶操舵杆 舵钮 舵销 舵柱rudder spindle 舵轴rudder stock 舵杆rudder trunk 舵杆围井rrr 去流段sss 中垂salvage lifting vessel 救捞船scale 缩尺，尺度schedule coordination 生产规程协调schedule reviews 施工生产进度审核轻型舱壁screen bulkheadSeakeeping performance 耐波性能seaspectra 海浪谱seastate 海况seakeeping 适航性seasickness 晕船seaworthness 适航性seaworthness 适航性section moulus 剖面模数section 剖面，横剖面self-induced 自身诱导的自航self-propulsionsemi-balanced rudder 半平衡舵semi-submersible drilling rig 半潜式钻井架shaft bossing 轴榖轴支架shaft bracketshaft coupling 联轴节剪切，剪力剪切性shearshear buckling 屈曲shear curve 剪力曲线sheer 舷弧sheer艉/艏舷弧aft/forward剖面图sheer drawingsheer plane 纵剖面sheer profile 总剖线，纵剖图船壳板shell platingship fitter 船舶装配工ship hydrodynamics 船舶水动力学shipway/slipway 船台船厂shipyardshrouded screw 有套罩螺旋桨，导管螺旋桨side frame 舷边肋骨side keelson 旁内龙骨side plate 舷侧外板side stringer 甲板边板casingstrength curves strength deck stressconcentrationstructuralinstability流线型套管 强度曲线 强力甲板应力集中single-cylinder engine sinkage 升沉 six degrees of freedom skin friction skirt单缸引擎 slamming sleeve 六自由度 表面摩擦力 气垫船）围裙 砰击 套管，套筒，套环 slewing hydraulic motor slice 一部分，薄片 sloping shipway 有坡度船台 sloping top plate of bottom side tank sloping bottom plate of topside tank soft chine 圆舭声纳 sonar spaderudder spectacle framespeed-to-length ratio sponson deck springing stability stable equilibrium starboard static equilibrium steamersteering gear stem stem contour stern stern barrelstern counter 回转液压马达 底边舱斜顶板 顶边舱斜底板悬挂舵 眼睛 型骨架 速长比 舷伸甲板 颤振 稳性 稳定平衡右舷静平衡汽轮船 操纵装置，舵机船艏船艉stern ramp stern transom plate stern wave stiffen stiffener straddle strai n strake streamline艏柱型线尾拖网滚筒 尾突体 尾滑道， 尾跳板爱 尾封板 艉波 加劲，加强 加劲杆 跨立，外 包式叶片 应变 船体列板 流线 扶强材， streamlined构不稳定性tonnage torpedo torquetrailing edge transom stern吨位鱼雷扭矩随边方尾strut 支柱，支撑构型subassembly 分部装配subdivision 分舱submerged nozzle 浸没式喷口submersible 潜期suction back of a blade Suez Canal tonnage summer load water line superintendent superstructure桨叶片抽吸叶背苏伊士运河吨位限制夏季载重水线监督管理人，总段长，车间主任上层建筑supper cavitating propeller 超空泡螺旋桨surface nozzle 水面式喷口surface piercing 穿透水面的surface preparation and coatingsurge 纵荡sway 横荡yaw 首摇surmount顶上覆盖，越过swage plate 压筋板swash bulkhead 止荡舱壁表面预处理与喷涂SWATH (Small Waterplane Area Twin Hull)tail-stabilizer anchor 尾翼式锚小水线面双体船talking paper 讨论文件切tangential 向的，正切的tangentialviscous force 切向粘性力tanker 油船tender交通小艇木材运timber carrier 输船tugboat 拖船tee T 型构件，三通管tensilestress 拉（张）应力thermal effect 热效应throttle valve 节流阀throughput 物料流量thrust 推力thruster 推力器，助推器tip of a blade 桨叶叶梢toed towards amidships 趾部朝向船舯transverse section 横剖面transverse stability 横稳性trawling 拖网trial 实船试验trim 纵倾trim by the stern/bow 艉 /艏倾trimaran三体的tripping bracket trough 波谷tumble home tunnel wall effect turnable bladeturnable shrouded screw tweendeck cargo space tweendedk frame two nodded frequency转动导管螺旋桨 甲板间舱 甲板间肋骨 双节点频率LCC 大型原油轮超级大型原油轮巨型原油轮 超声波的 （海运） 保险商非对称的 正浮位置 气化阱ventilation and air conditioning diagram viscosity 粘性 Voith-Schneider propeller vortex 梢涡 v 型剖面 伴流，尾流 喷水（推进）管 水线面 水密完整性 波形 消波器，消波板wave-making resistance 兴波阻力weather deck 露天甲板web 腹板 web beam强横梁web frame腹肋板防倾肘板 船侧）内倾 水 桶壁面效应 可转动式桨叶UUUUVVVV ultrasonic underwriter unsymmetrical upright position vaporpocket Venturi section文丘里试验段 通风与空调铺设设计vertical prismatic coefficientvertical-axis(cycloidal)propeller 横剖面系数 直叶（摆线）推进器 造船部件销售商v-section wakecurrent water jet water plane watertight integrity wave pattern wave suppressor外摆线直翼式推进器welder wetted surface winch windlass wing shaft wing-keel焊工湿表面积绞车起锚机侧轴翅龙骨（游艇）working allowance 有效使用修正量worm gear yacht yard issue yards 蜗轮，蜗杆快艇船厂开工任务发布书帆桁。

Vocabulary summary(二)⏹1.货舱： Cargo hold⏹甲板间舱（二层舱）tween deck space⏹二层甲板tween deck⏹上层甲板间舱upper tween deck space⏹中层甲板间舱mid tween deck space⏹下层甲板间舱lower tween deck space⏹下层舱lower hold⏹肋骨frame⏹货舱出入口access⏹2. 舱口和舱口盖： Hatchways and covers ⏹舱口hatchway, hatch⏹舱口活动横梁portable beam⏹舱口围板hatch(hatchway) coaming⏹舱口围板扶强材stiffener⏹舱口盖hatch cover⏹机械舱口盖mechanical hatchcover⏹绞链舱口盖swinging hatch cover⏹⏹液压折叠式舱口盖hydraulic-folding hatchcover⏹多板滚动式舱口盖multipanel hatchcover⏹滚动式舱口盖rolling hatchcover⏹滑动式舱口盖sliding hatchcover⏹舱盖板hatch cover plate(panel)⏹托架carrier⏹导轨guide rail⏹轨道轮子track wheel⏹3.甲板: Deck⏹甲板板deck plating⏹甲板开口deck opening⏹甲板边板deck stringer⏹甲板骨架deck framing⏹甲板纵桁deck girder⏹甲板纵骨deck longitudinal⏹甲板强横梁deck transverse⏹甲板横梁deck beam⏹主甲板main deck⏹上甲板upper deck⏹前甲板fore deck⏹后甲板after deck⏹第二甲板second deck⏹下层甲板lower deck⏹居住甲板accommodation dec k⏹上层建筑甲板superstructure deck⏹艏楼甲板forecastle deck⏹艉楼甲板poop deck⏹桥楼甲板bridge deck⏹驾驶甲板navigation deck⏹舱壁甲板bulkhead deck⏹甲板室甲板deckhouse deck⏹平台甲板platform deck⏹罗经甲板compass deck⏹干舷甲板freeboard deck⏹分舱甲板subdivision deck⏹强力甲板strength deck⏹开敞甲板open deck⏹露天甲板exposed (weather) deck⏹遮蔽甲板shelter deck⏹游步甲板promenade deck⏹旅客甲板passenger deck⏹升高甲板raised deck⏹前升高甲板raised fore deck⏹后升高甲板raised quarter deck⏹车辆甲板vehicle deck⏹甲板覆层Deck covering⏹化学敷料composition⏹绝缘层insulation⏹4. 支柱： Pillar⏹组合支柱built up pillar⏹立柱upright⏹5. 舱壁: Bulkhead⏹（非）水密舱壁(non-) watertight bulkhead ⏹横向舱壁transverse bulkhead⏹纵向舱壁longitudinal bulkhead⏹纵中舱壁central longitudinal bulkhead⏹防撞舱壁collision bulkhead⏹制荡舱壁wash bulkhead⏹平面舱壁plane bulkhead⏹槽形舱壁corrugated bulkhead⏹风雨密舱壁weathertight bulkhead⏹舱壁扶强材bulkhead stiffener⏹舱壁贯穿孔penetration⏹6. 肘板： Bracket⏹梁肘板beam knee⏹货舱内肋骨下端肘板lower bracket⏹舭肘板bilge bracket⏹上肘板upper bracket⏹防倾肘板tripping bracket⏹7. 通风筒： Ventilator⏹通风筒围板ventilator coaming⏹通风筒盖ventilator cover⏹通风筒帽ventilator cap⏹通风筒开口ventilator opening⏹防火挡板damper⏹防火网flame screen⏹风雨密关闭装置weathertight closing appliance ⏹8. 空气管： Air pipe⏹空气管头air pipe head⏹空气管管口air pipe opening⏹空气管接头air pipe connection⏹9. 开口： Opening⏹甲板开口Deck opening⏹货舱开口Hatch opening⏹机舱开口Machinery space opening⏹人孔Manhole⏹人孔盖Manhole cover⏹减轻孔Lightening hole⏹泄水孔Scupper⏹排水孔Discharge⏹进水孔Inlet⏹流水孔Drain hole⏹透气孔Air hole⏹吸口Suction。

船舶专业英语词汇1, steering ['sti?ri?]n. 操纵；指导；掌舵v. 驾驶；掌舵（steer的ing形式）2, gear [ɡi?]n. 齿轮；装置，工具；传动装置vi. 适合；搭上齿轮；开始工作vt. 开动；搭上齿轮；使……适合；使……准备好adj. 好极了3, refrigeration [ri,frid??'rei??n, ri:-]n. 制冷；冷藏；[热] 冷却4, provision [pr?u'vi??n]n. 规定；条款；准备；[经] 供应品vt. 供给…食物及必需品5, store [st?:]n. 商店；储备，贮藏；仓库vt. 贮藏，储存6, tally ['t?li]n. 计数器；标签；记账vt. 使符合；计算；记录vi. 一致；记分7, changing ['t?eind?i?]v. 改变（change的ing形式）；交换；兑换n. 改变；转换；替换adj. 变化的；发展的8, gym [d?im]n. 健身房；体育；体育馆9, electric [i'lektrik]adj. 电的；电动的；发电的；导电的；令人震惊的n. 电；电气车辆；带电体10, channel ['t??n?l]vt. 引导，开导；形成河道n. 通道；频道；海峡11, pipe joint管接；导管接头12, pipe [paip]n. 管；烟斗；笛vi. 吹笛；尖叫vt. 用管道输送；尖声唱；用管乐器演奏13, laundry ['l?:ndri, 'lɑ:n-]n. 洗衣店，洗衣房；要洗的衣服；洗熨；洗好的衣服14, sanitary ['s?nit?ri]adj. 卫生的，清洁的n. 公共厕所15, case [keis]n. 情况；实例；箱vt. 包围；把…装于容器中16, etcadv. 等等，及其他17, accommodation [?,k?m?'dei??n]n. 住处，膳宿；调节；和解；预订铺位18, forepeak ['f?:pi:k]n. 船首舱19, airconabbr. 空调（Air conditioning）20, galley ['ɡ?li]n. [船] 船上的厨房；单层甲板的大帆船；活版盘，长条校样21, mess [mes]n. 混乱；食堂，伙食团；困境；脏乱的东西vt. 弄乱，弄脏；毁坏；使就餐vi. 把事情弄糟；制造脏乱；玩弄22, toilet ['t?ilit]n. 厕所，盥洗室；梳妆，打扮vi. 梳妆，打扮vt. 给…梳妆打扮23, stair [stε?]n. 楼梯，阶梯；梯级24, crew [kru:]n. 队，组；全体人员，全体船员vi. 一起工作vt. 使当船员25, conference room会议室，会议厅26, conferencen. 会议；协商；讨论；[篮]联盟27, captain ['k?ptin]n. 队长，首领；船长；上尉；海军上校vt. 指挥；率领28, chief engineer[劳经] 总工程师；轮机长；主任工程师；总技师29, pilot ['pail?t]n. 飞行员；领航员adj. 试点的v. 驾驶；领航；试用30, charging ['t?ɑ:d?i?]n. 炉料；装料v. 使承担（任务等）；装载；命令（charge的现在分词）31, discharge [dis't?ɑ:d?, 'dist?ɑ:d?, dis't?-]vt. 解雇；卸下；放出；免除vi. 排放；卸货；流出n. 排放；卸货；解雇32, radar ['reid?]n. [雷达] 雷达，无线电探测器33, mast [mɑ:st, m?st]n.桅杆；柱；橡树果实vt. 在…上装桅杆34, communication [k?,mju:ni'kei??n]n. 通讯，[通信] 通信；交流35, signal ['siɡn?l]n. 信号；暗号；导火线vt. 标志；用信号通知adj. 显著的；作为信号的vi. 发信号36, recorded [ri'k?:did]adj. 记录的v. 记录；录音（record的过去分词）37, general arrangement总布置38, reliale39, assessed [?'sest]v. 对…进行评估（assess过去时形式）40, maintainedadj. 被保持的v. 维护，维修；维持（maintain的过去分词）41, yacht [j?t]vi. 乘游艇，驾游艇n. 游艇，快艇；轻舟42, overhaul [,?uv?'h?:l, '?uv?h?:l]vt. 分解检查，大修；追上并超过n. 彻底检修，详细检查43, maintenance ['meint?n?ns]n. 维护，维修；保持；生活费用44, extremesn. 狂热分子，极端条件45, encounter [in'kaunt?]vt. 遭遇，邂逅；遇到n. 遭遇，偶然碰见vi. 遭遇；偶然相遇46, encountered [in'kaunt?d]v. 遇到；曾遭遇（encounter的过去式）47, toll [t?ul, t?l]损失。

船舶与海洋工程专业专业英语词汇1、A类a faired set of lines 经过光顺的一组型线abaft 朝向船尾absence 不存在accommodation 居住(舱室acquisition cost 购置(获取成本activate 作动adopt 采用aegis 保护,庇护aerostatic 空气静力学的after perpendicular (a. p. 艉柱ahead and astern 正车和倒车air cushion vehicle 气垫船aircraft carrier 航空母舰airfoil 气翼,翼剖面,机面,方向舵airfoil 气翼,机翼alignment chock 组装校准用垫楔(或填料allowance 公差,余(裕量,加工裕量,补贴American Bureau of Shipping (美国船级社amidships 舯amidships 在舯部amphibious 两栖的angle of attack 攻角angle plate 角钢anticipated loads encountered at sea在海上遭遇到的预期载荷antiroll fins 减摇鳍appendage 附体appendage 附件,附体appendage 附体artisan 技工assembly line 装配(流水线athwart ships 朝(船横向at-sea replenishment 海上补给axiomatic 理所当然的,公理化的2、B类back up member 焊接垫板backing structure 垫衬结构Bar 型材,材bar keel 棒龙骨,方龙骨,矩形龙骨barge 驳船base line 基线base, base line 基线basic design 基本设计batten 压条,板条be in short supply 供应短缺、俏销beam 船身最大宽,横梁beam 船宽,梁bench work 钳工bevel 折角bid 投标bidder 投标人(者bilge 舭,舱底bilge 舭bilge keel 舭龙骨bilge radius 舭半径bills of material 材料(细目单blast 喷丸(除锈block coefficient 方形系数block coefficient 方形系数Board of Trade (英国贸易厅body plan 横剖面图body section 横剖图Bonjean curve 邦戎曲线boom 吊杆boundary layer 边界层bow line 前体纵剖线bow thruster 艏侧推器bow wave 艏波boyant 浮力的bracket 轴支架,支架breadth extreme 最大宽,计算宽breadth moulded 型宽breakbulk 件杂货buckle 屈曲budget 预算,作预算buffer area 缓冲区building basin 船台bulb plate 球头扁钢bulbous bow 球状船艏bulbous bow 球鼻艏bulk oil carrier 散装油轮bulk carrier 散装货船bulk carrier 散装货船buoyancy 浮力buoyancy 浮力Bureau Veritas (法国船级社burning machine 烧割机butt weld 对缝焊接buttock 后体纵剖线by convention 按照惯例,按约定3、C类camber 梁拱capacity plan 舱容图capsize 倾覆capsizing moment 倾覆力矩captured-air-bubble vehicle 束缚气泡减阻船cargo capacity 载货量,货舱容量,舱容cargo cubic 货舱舱容,载货容积cargo handling 货物装卸cargo owner 货主carpenter 木匠carriage of grain cargoes 谷类货物输运机cascading of waves upon…海浪跌落于…casualty 事故,死伤,灾难catamaran 双体船categorize 分类centroid 形心,重心,质心,矩心chine 舭,舷,脊chock 木楔circumscribe 外接,外切circumsection 外切Coast Guard cuttle(美国海岸警备队快艇commercial ship 营利用船commissary spaces 补给库舱室,粮食库common carrier 通用运输船compartment 舱室concave 凹,凹的,拱conceive 设想,想象concept design 概念设计configuration 构形,配置configuration安排,构型,配置conspicuous 显著的,值得注意的containerized 集装箱化contract design 合同设计contract design 合同设计contracted scale 缩尺core box 型芯corrosion 锈蚀,腐蚀couple 力矩,力偶crest (of wave 波峰crew quarters 船员居住舱Critical Path Method (CPM 关键路径法cross section 横剖面cross sectional area 横剖面面积cross-channel automobile ferries 横越海峡客车渡轮crucial element 重要因素cruiser stern 巡洋舰尾cruissing range 航程curvature 曲率curves of form 各船型曲线cushion of air 气垫4、D类damage stability 破损稳性damp out 阻息,逐渐降低dead load 恒(静载荷deadweight 总载重量(吨deballast 卸除压载(压舱deck line at side 甲板边线deck camber 甲板梁拱deck wetness 甲板淹湿deckhouse 舱面室,甲板室declivity 坡度,斜度deep V hull 深V型船体deformation 变形delivery 交船Department of Trade (英国贸易部deposit metallic plating 镀上金属镀层depth moulded 型深depth 船深depth 船深design spiral 螺旋式设计destroyer 驱逐舰detail design 详细设计deviation 偏离,偏差devious 曲折的diagram 图,原理图,设计图,流程图dimension 尺度,元,维displacement 排水量distributed load 分布载荷division 站,划分,分隔do work 做功dock 泊靠draft 吃水draftsman 绘图员drag 阻力Drainage 排(泄水draught(=draft 吃水,草图,设计图,牵引力drawing office 绘图室dredge 挖泥船drift 飘移,偏航drilling rig 钻架dry dock 干船坞5、E类eddy 旋涡electrohydraulic 电动液压的electroplater 电镀工elevations 高度,高程,船型线图的侧面图、立视图,纵剖线图enclosed fabrication shop 封闭式装配车间end on 端对准endurance 续航力launch 发射,下水launching equipment(向水中投放设备launching way (船舶下水滑道LCC(Large Crude Carrier大型原油轮(载重10~20万吨lead time 设计至投产、定货至交货的时间legislation 立法length between perpendicular 两柱间长leveler 调平器,矫平机,矫直机life saving appliance 救生设备life-cycle cost 生命周期成本第二,中国坚持走和平发展的道路。

a faired set of lines 经过光顺的一组型线abaft 朝向船尾abaft 朝船尾absence 不存在accommodation 居住(舱室)acquisition cost 购置（获取）成本activate 作动adopt 采用aegis 保护，庇护aerostatic 空气静力学的after perpendicular (a. p. ） 艉柱ahead and astern 正车和倒车air cushion vehicle 气垫船aircraft carrier 航空母舰airfoil 气翼，翼剖面，机面，方向舵airfoil 气翼，机翼alignment chock 组装校准用垫楔(或填料)allowance 公差，余(裕)量，加工裕量，补贴 American Bureau of Shipping (美国)船级社amidships 舯amidships 在舯部amphibious 两栖的angle of attack 攻角angle plate 角钢anticipated loads encountered at sea在海上遭遇到的预期载荷antiroll fins 减摇鳍appendage 附体appendage 附件，附体appendage 附体artisan 技工assembly line 装配(流水)线athwart ships 朝 (船)横向at-sea replenishment 海上补给axiomatic 理所当然的，公理化的back up member 焊接垫板backing structure 垫衬结构Bar 型材，材bar keel 棒龙骨，方龙骨，矩形龙骨barge 驳船base line 基线base, base line 基线basic design 基本设计batten 压条，板条be in short supply 供应短缺、俏销 beam 船身最大宽，横梁beam 船宽，梁bench work 钳工bevel 折角bid 投标bidder 投标人(者)bilge 舭，舱底bilge 舭bilge keel 舭龙骨bilge radius 舭半径bills of material 材料(细目)单 blast 喷丸(除锈)block coefficient 方形系数block coefficient 方形系数Board of Trade (英国)贸易厅 body plan 横剖面图body section 横剖图Bonjean curve 邦戎曲线boom 吊杆boundary layer 边界层bow line 前体纵剖线bow thruster 艏侧推器bow wave 艏波boyant 浮力的bracket 轴支架，支架breadth extreme 最大宽，计算宽breadth moulded 型宽breakbulk 件杂货buckle 屈曲budget 预算，作预算buffer area 缓冲区building basin 船台bulb plate 球头扁钢bulbous bow 球状船艏bulbous bow 球鼻艏bulk oil carrier 散装油轮bulk carrier 散装货船bulk carrier 散装货船buoyancy 浮力buoyancy 浮力Bureau Veritas (法国)船级社burning machine 烧割机butt weld 对缝焊接buttock 后体纵剖线by convention 按照惯例，按约定camber 梁拱capacity plan 舱容图capsize 倾覆capsizing moment 倾覆力矩captured-air-bubble vehicle 束缚气泡减阻船cargo capacity 载货量，货舱容量，舱容cargo cubic 货舱舱容，载货容积cargo handling 货物装卸cargo owner 货主carpenter 木匠carriage of grain cargoes 谷类货物输运机cascading of waves upon… 海浪跌落于 …casualty 事故，死伤，灾难catamaran 双体船categorize 分类centroid 形心，重心，质心，矩心chine 舭，舷，脊chock 木楔circumscribe 外接，外切circumsection 外切Coast Guard cuttle(美国）海岸警备队快艇commercial ship 营利用船commissary spaces 补给库舱室，粮食库common carrier 通用运输船compartment 舱室concave 凹，凹的，拱conceive 设想，想象concept design 概念设计configuration 构形，配置configuration安排，构型，配置conspicuous 显著的，值得注意的containerized 集装箱化contract design 合同设计contract design 合同设计contracted scale 缩尺core box 型芯corrosion 锈蚀，腐蚀couple 力矩，力偶crest (of wave) 波峰crew quarters 船员居住舱Critical Path Method (CPM) 关键路径法cross section 横剖面cross sectional area 横剖面面积cross-channel automobile ferries 横越海峡客车渡轮crucial element　重要因素cruiser stern 巡洋舰尾cruissing range 航程curvature 曲率curves of form 各船型曲线cushion of air 气垫damage stability 破损稳性damp out 阻息，逐渐降低dead load 恒(静)载荷deadweight 总载重量(吨)deballast 卸除压载(压舱)deck line at side 甲板边线deck camber 甲板梁拱deck wetness 甲板淹湿deckhouse 舱面室，甲板室declivity 坡度，斜度deep V hull 深V型船体deformation 变形delivery 交船Department of Trade (英国)贸易部deposit metallic plating 镀上金属镀层depth moulded 型深depth 船深depth 船深design spiral 螺旋式设计destroyer 驱逐舰detail design 详细设计deviation 偏离，偏差devious 曲折的diagram 图，原理图，设计图，流程图dimension 尺度，元，维displacement 排水量distributed load 分布载荷division 站，划分，分隔do work 做功dock 泊靠draft 吃水draftsman 绘图员drag 阻力Drainage 排(泄)水draught(=draft) 吃水，草图，设计图，牵引力drawing office 绘图室dredge 挖泥船drift 飘移，偏航drilling rig 钻架dry dock 干船坞eddy 旋涡electrohydraulic 电动液压的electroplater 电镀工elevations 高度，高程，船型线图的侧面图、立视图，纵剖线图 enclosed fabrication shop 封闭式装配车间end on 端对准endurance 续航力endurance 续航性entrance 进流段erection (船体)组装erection 装配，安装expedient 权宜之计extrapolate 外插f. p. = forward perpendicular 艏柱fair 光顺fair 光顺fastening 坚固件,紧固法fatigue 疲劳feasibility study 可行性研究fender 护舷ferry 渡轮，渡口，渡运航线ferry 轮渡(载运)fillet weld connection 贴角焊连接fine fast ship 纤细(细长)高速船fine form 瘦长(细长)船形Flank 侧面, 侧翼, 侧攻flanking rudders 侧翼舵flare 外飘，外张flat of keel 平板龙骨fleets of vessels 船队flexural 挠曲的float 浮动时间floating drydock 浮船坞flood 进水，泛滥floodable length curve 可浸长度曲线flow pattern 流型，流线谱flow of materials 物流flush 平贴，磨光forging 锻件，锻造form coefficient 船形系数forming operation 成型加工forward/after perpendicular 艏/艉柱forward/after shoulder 前/后肩foundry casting 翻砂铸造foundryman 铸造翻砂工frame 船肋骨，框架，桁架frame 框架freeboard 干舷freeboard 干舷freeboard 干舷freeboard deck 干舷甲板freight rate 运费率fresh water 淡水frictional resistance 摩擦阻力Froude number 傅汝德数full form 丰满船形full form ship 丰满船型fullness 丰满度funnel 烟囱galley (船舰，飞机的)厨房Gantt Chart 施工进度表general arrangement 总布置general arrangement 总布置Germanischer Lloyd (德国)劳埃德船级社girder 桁，梁gradient 梯度grating 格栅Green Book (船级社)绿皮书 (登录快速远洋船) ground level building site 平地建造场group technology 成组建造技术grouting 填缝、灌浆guided-missile cruiser 导弹巡洋舰habitability 适居性half breadth plan 半宽图handling equipment 装卸设备hard chine 尖舭headroom 净空高度heave 垂荡heel 横倾heel 柱脚，踵材，底基，倾斜hog 中拱hogging 中拱hold 船舱hole 水流深凹处homogeneous cylinder 均质柱状体hopper barge (自动)倾卸驳hostile sea 凶险的波浪hostile sea 汹涌波浪hull block 船体垫块，船体支座hull form 船形hull form 船形HVAC (=heating, ventilating and cooling) 取暖，通风与冷却hydraulic mechanism 液压机构hydrodynamic 水动力学的hydrofoil 水翼hydrostatic 水静力的icebreaker 破冰船icebreaker 破冰船identified as Essential Changes 标记作“必备变更项”immerse 浸入immerse 浸没impact load 冲击载荷imperial unit 英制单位impression 模槽，型腔，印痕，印象in strake 内列板in way of… 在…处inboard profile 纵剖面图In-depth analysis 深入研究initial stability at small angle of inclination 小倾角初稳性insulation 绝缘，隔离Intact stability　完整稳性Intergovernmental Maritime Consultative Organization 国际海事质询组织Intergovernmental Maritime Consultative Organization (IMCO) 国际政府间海事质询组织International Association of Classification Society (IACS) 国际船级社联合会 International Convention for the Safety of Life at Sea (ICSOLAS) 海上生命安全性国际公约International Towing Tank Conference 国际船模试验水池会议intersection 交点，交叉，横断(切)intervening deck 居中甲板introduces a bill 提出一项议案issue periodically 定期发布(公布)iterative process 选代过程jack 千斤顶janitorial 勤杂工，房屋照管者joggle 折曲，榫接，弯合joiner 安装工joiner 细木工(匠)joinery 细木工keel 龙骨keel laying 开始船舶建造(原意为“铺设龙骨架”)Kips (= kilo-pounds) 千磅laborer 力工Land borne 陆基的，装在陆地的landing craft 登陆艇large tank and sphere 大型油罐和球罐launch 发射，下水launching equipment（向水中）投放设备launching way (船舶)下水滑道LCC(Large Crude Carrier）大型原油轮（载重10~20万吨）lead time 设计至投产、定货至交货的时间legislation 立法length between perpendicular 两柱间长Length overall 总长leveler 调平器，矫平机，矫直机life saving appliance 救生设备life-cycle cost 生命周期成本lift fan 升力风扇lift offsets 量取型值Light ship weight 空船重量lighter　港驳船likely 多半，可能line 型线liner 定期航班船liner trade 定期班轮营运业lines plan 型线图liquefied gas carrier 液化气运输船list 倾斜, 表living and utility spaces 居住与公用舱室Lloyd’s Machinery Certificate (LMC) 劳埃德(船舶)机械证书Lloyd’s Register of Shipping (英国)劳埃德船级社Lloyds Rules 劳埃德(船级社)规范LNG containment 液化天然气容器Load Line Regulation 载重线公约、规范load waterline 载重水线load waterplane 载重水线面loft floor 放样台full scale 全尺度loftman 放样工loftman 放样工longitudinal　纵向的longitudinal 纵向的，纵梁longitudinal prismatic coefficient 纵向棱形系数machinery vendor 机械(主机)卖方magnet gantry 磁力式龙门吊maiden voyage 处女航main shafting 主轴系major ship 大型船舶maneuverability 操纵性maritime 海事的，海运的，靠海的，沿海的mark out 划线，划记号marshal 调度mast 桅杆maximum beam amidships 舯最大宽member 部件merchant ship 商船metacenter 稳心metacentric height　稳心高metal plate bath 金属板电镀槽metal worker 金属工metric unit 公制单位midbody （船）中体middle line plane 中线面midship area coefficient 舯横剖面系数midship section 舯横剖面midship section coefficient 舯横剖面系数mill shape 轧钢厂型材module assembly 模块式组装mold loft floor (型线)放样间地板molded lines 型线molder 造型工mould loft 放样间moulded line 型线multihull vessel 多体船Multi-ship program 多种船型建造规划nautical mile 海里naval architect 造船师naval architecture 造船工程naval ship 军船naval architecture 造船学nearuniversal gear 准万向齿轮network flow 网络流程neutral equilibrium 中性平衡normal 法向，法向的 ，正交的normal force 法向力normal operating condition 常规(正常)运作工况notch 开槽，开凹口Off the shelf 成品的，畅销的，流行的off-center loading　偏移中心的装载offsets 型值offshore drilling 离岸钻井oil-rig 钻油架operational requirement 军事行动需求，运作要求 orient 取向，定方位，调整orthogonal 正交的，矩形的out strake 外列板outboard profile 侧视图outfit 舾装outfitter 舾装工outfitting 舾装overall stability 总体稳性overhang 外悬overstocking 存货过剩owner’s staff 船东的雇(职)员paint priming 涂底漆Panama Canal 巴拿马运河panel line system 板材生产线系统parallel middle body 平行中体patternmaker 木模工payload 有效载荷permanent body 永久性组织机构perpendicular（船艏、艉）柱，垂直的，正交的pillar 支柱pin 钉，销pin jig 限位胎架pintle 销，枢轴pipe fitter 管装工pipe laying barge (海底) 铺管驳船piping 管路pitch 纵摇plan views 设计图planing hull 滑行船体pleasure ship 游乐用船Plimsoll line 普林索尔载重线polar-exploration craft 极地考察船Polaris (submarine) 北极星级(潜艇)port 左舷portable gate 移动式(可移动)闸门positive righting arm 扶正力臂power and lighting system 动力与照明系统preliminary design 初步设计preliminary/concept design 初步/概念设计pressure vessel 压力容器principal dimensions 主尺度prism 棱柱体prismatic coefficient 棱形系数procurement 采购，获得Program Evaluation and Review Technique 规划评估与复核法quartering sea 尾斜浪, 从船斜后方来的浪quay(横)码头，停泊所racking 倾斜，变形，船体扭转变形radiography X射线照相术，X射线探伤rake 倾角,倾斜ram pressure 速压头，冲压，全压力rectangle 矩形reenlistment 重征服役Registo Italiano Navale (意大利)船级社remedial action 补救措施reserve buoyancy 储备浮力reserve buoyancy 储备浮力residuary resistance 剩余阻力resultant　合力resultant 合力retract 收进revolving crane 旋转式(鹤)吊，转臂吊(车)Reynolds number 雷诺数rigger 索具装配工rigid side walls 刚性侧壁rise of floor 底升risk 保险对象，保险金额rivering warfare vessel 内河舰艇rivet 铆接，铆钉roll 横摇rolled angle butt (轧制)角钢焊接头roll-on/roll-off(RO-RO) 滚装rough sea 汹涌的波浪round of beam 梁拱rounded gunwale 修园的舷边rubber tile 橡皮瓦rudder post 舵柱rudder 舵rudder rate 舵率rudder stock 舵杆run 去流段Sag 中垂sagging 中垂scale 缩尺，尺度，尺scale model 缩尺船模scantling 材积sea keeping performance 耐波性能 seasickness 晕船seaworthiness 适航性section 剖面，横剖面sections (铁、钢)型材，轧材self-induced 自身诱导的semi finished item 半精加工件 semisubmersible drilling rig 半潜式钻井架set course 设定的航线set course 设定航线shaft bossing 轴包套shaft bracket 轴支架shear 剪切，剪力sheer aft 艉舷弧sheer forward 艏舷弧sheer drawing 剖面图 sheer plane 纵剖面sheer profile 纵剖线sheer profile 纵剖图sheer(甲板)舷弧sheet metal work 钣金工，冷作工shell plating 船壳板shell 船壳板ship fitter 船舶装配工ship fitter 船体安装工ship fitter 舰船装配工ship form 船型ship Hydrodynamics 水动力学ship owner 船东shipping line 船运航线shipway (造)船台shipwright 船体装配工，造船工人 shipyard 船厂shipyard 船厂shipyard schedule chart 船厂施工进度图 shoring 支撑，支柱shoulder 船肩sideways 朝侧向six degrees of freedom 六自由度sizable 相当大的skirt（气垫船）围裙slamming 砰击，拍击slice 一部分，薄片sloping shipway 有坡度船台，滑道soft chine 圆舭spare part 备件specially prepared form 专门(特殊)加工的模板 spectrum 谱speed-to-length ratio 速长比stability 稳性stable equilibrium 稳定平衡standard 规章starboard 右舷static equilibrium 静平衡statically determinant 静定的statistical 统计学(上)的steel marking 钢板划线steering gear 操纵装置steering gear 操纵装置，舵机stem 船艏stem contour 艏柱型线stern 艉stern frame 艉构架，艉框架stern wave 艉波stiffen 加劲，加强stiffener 肋骨strain 应变strake 船体列板stringent safety regulations 严格的安全规章structural alignment 结构校准，组合，组装strut 支柱，支撑构形subassembly (局部)分部装配subdivision 分舱sublet 转包，分包，转租submersible 潜器suction cup 吸盘Suez Canal Tonnage 苏伊士运河吨位限制summer load water line 夏季载重水线super cavitating propeller超空泡螺旋桨superintendent 监督管理人，总段长，车间主任superstructure 上层建筑supertanker 超级油轮supervision of the Society’s surveyor 船级社验船师的监造surface piercing 穿透水面的surface preparation and coating 表面加工处理与喷涂surge 纵荡surmount 顶上覆盖，越过survivability 生存力SWATCH(Small Waterplane Area Twin Hull) 小水线面双体船sway 横荡switchboard 控制台，开关板tabular freeboard 列成表格的干舷值tacker 定位搭焊工talking paper 讨论文件tangential viscous force 切向粘性力tanker 油轮tanker 油轮tantamount 等值的，相当的taper 弄细，变尖tee T形构件，三通管template 样板tensile stress 拉(张)应力The Register of Shipping of the People’s Republic of China 中国船舶检验局The Titanic 泰克尼克号(巨型邮轮)there is more shape to the shell 船壳板的形状较复杂titanic 巨大的to be craft oriented 与行业有关的，适应于行业性的to run the waterlines 绘制水线toed towards amidships 趾部朝向船舯ton gross=gross ton 长吨=1. 016公吨tonnage 吨位torque 扭矩torsio 扭转的trade 工种, 贸易trailer type transporter 拖车式载运车transfer sideways 横向移动transom (stern) 方尾transverse　横向的transverse bulkhead plating 横隔舱壁板transverse section 横剖面transverse stability 横稳性trawling 拖网trial 实船试验trim 纵倾trim 纵倾trim by the stern/bow 艉/艏倾trimaran 三体船trough 波谷tugboat 拖船tumble home(船侧)内倾Type A ship A类船U form U型U. S. Coast Guard 美国海岸警卫队ULCC(Ultra Large Crude Carrier）超级大型原油轮（载重量>40万吨）ultrasonic 超声波的\underwriter (海运)保险商undock 使船出坞upright position 正浮位置V shaped V型的ventilation and air conditioning diagram 通风与空调敷设设计图vertical prismatic coefficient 垂向棱形系数vertical prismatic coefficient 垂向棱形系数vicinity 邻近，附近villain 坏人，罪魁viscosity 粘性VLCC(Very Large Crude Carrier）巨型（原）油轮（载重量>20万吨）V-sectionV型剖面wash 下洗 ,艉流water line 水线waterborne 浮于水上的，水基的waterplane 水线面waterplane area coefficient 水线面积系数watertight integrity 水密完整性wave pattern 波型wavemaking resistance 兴波阻力weather deck 露天甲板weld inspection 焊缝检测welder 焊工weldment 焊件，焊接装配wetted surface 湿面积wing shaft 侧轴yacht 快艇yard issue 船厂开工任务发布书yaw 艏摇yaw 艏摇，摇艏。

船舶与海洋工程专业专业英语词汇1、A类a faired set of lines 经过光顺的一组型线 abaft 朝向船尾absence 不存在accommodation 居住(舱室)acquisition cost 购置（获取）成本activate 作动adopt 采用aegis 保护，庇护aerostatic 空气静力学的after perpendicular (a. p. ）艉柱ahead and astern 正车和倒车 air cushion vehicle 气垫船aircraft carrier 航空母舰airfoil 气翼，翼剖面，机面，方向舵airfoil 气翼，机翼alignment chock 组装校准用垫楔(或填料)allowance 公差，余(裕)量，加工裕量，补贴 American Bureau of Shipping (美国)船级社amidships 舯amidships 在舯部amphibious 两栖的angle of attack 攻角angle plate 角钢 anticipated loads encountered at sea在海上遭遇到的预期载荷antiroll fins 减摇鳍 appendage 附体appendage 附件，附体 appendage 附体artisan 技工 assembly line 装配(流水)线athwart ships 朝 (船)横向 at-sea replenishment 海上补给axiomatic 理所当然的，公理化的2、B类back up member 焊接垫板 backing structure 垫衬结构Bar 型材，材bar keel 棒龙骨，方龙骨，矩形龙骨barge 驳船 base line 基线base, base line 基线basic design 基本设计batten 压条，板条 be in short supply 供应短缺、俏销beam 船身最大宽，横梁beam 船宽，梁bench work 钳工 bevel 折角bid 投标 bidder 投标人(者)bilge 舭，舱底bilge 舭bilge keel 舭龙骨 bilge radius 舭半径bills of material 材料(细目)单 blast 喷丸(除锈)block coefficient 方形系数block coefficient 方形系数Board of Trade (英国)贸易厅 body plan 横剖面图body section 横剖图 Bonjean curve 邦戎曲线boom 吊杆 boundary layer 边界层bow line 前体纵剖线 bow thruster 艏侧推器bow wave 艏波boyant 浮力的bracket 轴支架，支架breadth extreme 最大宽，计算宽breadth moulded 型宽breakbulk 件杂货buckle 屈曲budget 预算，作预算buffer area 缓冲区building basin 船台 bulb plate 球头扁钢bulbous bow 球状船艏bulbous bow 球鼻艏bulk oil carrier 散装油轮bulk carrier 散装货船bulk carrier 散装货船 buoyancy 浮力buoyancy 浮力Bureau Veritas (法国)船级社burning machine 烧割机 butt weld 对缝焊接buttock 后体纵剖线by convention 按照惯例，按约定3、C类camber 梁拱capacity plan 舱容图capsize 倾覆capsizing moment 倾覆力矩captured-air-bubble vehicle 束缚气泡减阻船cargo capacity 载货量，货舱容量，舱容cargo cubic 货舱舱容，载货容积cargo handling 货物装卸 cargo owner 货主carpenter 木匠 carriage of grain cargoes 谷类货物输运机cascading of waves upon…海浪跌落于… casualty 事故，死伤，灾难catamaran 双体船categorize 分类centroid 形心，重心，质心，矩心 chine 舭，舷，脊chock 木楔 circumscribe 外接，外切circumsection 外切Coast Guard cuttle(美国）海岸警备队快艇commercial ship 营利用船commissary spaces 补给库舱室，粮食库common carrier 通用运输船compartment 舱室 concave 凹，凹的，拱conceive 设想，想象concept design 概念设计configuration 构形，配置configuration安排，构型，配置conspicuous 显着的，值得注意的containerized 集装箱化 contract design 合同设计contract design 合同设计 contracted scale 缩尺core box 型芯 corrosion 锈蚀，腐蚀couple 力矩，力偶crest (of wave) 波峰crew quarters 船员居住舱 Critical Path Method (CPM) 关键路径法cross section 横剖面 cross sectional area 横剖面面积cross-channel automobile ferries 横越海峡客车渡轮crucial element 重要因素cruiser stern 巡洋舰尾cruissing range 航程curvature 曲率curves of form 各船型曲线cushion of air 气垫4、D类damage stability 破损稳性 damp out 阻息，逐渐降低dead load 恒(静)载荷 deadweight 总载重量(吨)deballast 卸除压载(压舱)deck line at side 甲板边线deck camber 甲板梁拱deck wetness 甲板淹湿 deckhouse 舱面室，甲板室declivity 坡度，斜度 deep V hull 深V型船体deformation 变形 delivery 交船Department of Trade (英国)贸易部 deposit metallic plating 镀上金属镀层depth moulded 型深depth 船深depth 船深 design spiral 螺旋式设计destroyer 驱逐舰detail design 详细设计deviation 偏离，偏差 devious 曲折的diagram 图，原理图，设计图，流程图 dimension 尺度，元，维displacement 排水量distributed load 分布载荷division 站，划分，分隔do work 做功dock 泊靠draft 吃水draftsman 绘图员 drag 阻力Drainage 排(泄)水draught(=draft) 吃水，草图，设计图，牵引力drawing office 绘图室 dredge 挖泥船drift 飘移，偏航drilling rig 钻架 dry dock 干船坞5、E类eddy 旋涡electrohydraulic 电动液压的electroplater 电镀工 elevations 高度，高程，船型线图的侧面图、立视图，纵剖线图 enclosed fabrication shop 封闭式装配车间end on 端对准 endurance 续航力endurance 续航性 entrance 进流段 erection (船体)组装erection 装配，安装 expedient 权宜之计extrapolate 外插f. p. = forward perpendicular 艏柱fair 光顺 fair 光顺fastening 坚固件,紧固法fatigue 疲劳 feasibility study 可行性研究 fender 护舷ferry 渡轮，渡口，渡运航线ferry 轮渡(载运) fillet weld connection 贴角焊连接fine fast ship 纤细(细长)高速船 fine form 瘦长(细长)船形Flank 侧面, 侧翼, 侧攻flanking rudders 侧翼舵flare 外飘，外张flat of keel 平板龙骨fleets of vessels 船队 flexural 挠曲的float 浮动时间 floating drydock 浮船坞 flood 进水，泛滥floodable length curve 可浸长度曲线 flow pattern 流型，流线谱flow of materials 物流 flush 平贴，磨光forging 锻件，锻造 form coefficient 船形系数forming operation 成型加工 forward/after perpendicular 艏/艉柱forward/after shoulder 前/后肩 foundry casting 翻砂铸造 foundryman 铸造翻砂工 frame 船肋骨，框架，桁架frame 框架 freeboard 干舷freeboard 干舷freeboard 干舷freeboard deck 干舷甲板 freight rate 运费率fresh water 淡水 frictional resistance 摩擦阻力Froude number 傅汝德数full form 丰满船形full form ship 丰满船型 fullness 丰满度funnel 烟囱galley (船舰，飞机的)厨房Gantt Chart 施工进度表 general arrangement 总布置general arrangement 总布置 Germanischer Lloyd (德国)劳埃德船级社 girder 桁，梁gradient 梯度grating 格栅 Green Book (船级社)绿皮书 (登录快速远洋船) ground level building site 平地建造场 group technology 成组建造技术grouting 填缝、灌浆 guided-missile cruiser 导弹巡洋舰habitability 适居性half breadth plan 半宽图handling equipment 装卸设备 hard chine 尖舭headroom 净空高度heave 垂荡 heel 横倾heel 柱脚，踵材，底基，倾斜 hog 中拱hogging 中拱 hold 船舱hole 水流深凹处homogeneous cylinder 均质柱状体hopper barge (自动)倾卸驳 hostile sea 凶险的波浪hostile sea 汹涌波浪 hull block 船体垫块，船体支座 hull form 船形hull form 船形 HVAC (=heating, ventilating and cooling) 取暖，通风与冷却hydraulic mechanism 液压机构 hydrodynamic 水动力学的hydrofoil 水翼hydrostatic 水静力的icebreaker 破冰船icebreaker 破冰船identified as Essential Changes 标记作“必备变更项” immerse 浸入 immerse 浸没impact load 冲击载荷imperial unit 英制单位impression 模槽，型腔，印痕，印象in strake 内列板 in way of…在…处inboard profile 纵剖面图 In-depth analysis 深入研究initial stability at small angle of inclination 小倾角初稳性insulation 绝缘，隔离Intact stability 完整稳性Intergovernmental Maritime Consultative Organization 国际海事质询组织Intergovernmental Maritime Consultative Organization (IMCO) 国际政府间海事质询组织International Association of Classification Society (IACS) 国际船级社联合会International Convention for the Safety of Life at Sea (ICSOLAS) 海上生命安全性国际公约International Towing Tank Conference 国际船模试验水池会议intersection 交点，交叉，横断(切)intervening deck 居中甲板introduces a bill 提出一项议案 issue periodically 定期发布(公布)iterative process 选代过程jack 千斤顶 janitorial 勤杂工，房屋照管者joggle 折曲，榫接，弯合 joiner 安装工joiner 细木工(匠)joinery 细木工keel laying 开始船舶建造(原意为“铺设龙骨架”) Kips (= kilo-pounds) 千磅laborer 力工Land borne 陆基的，装在陆地的 landing craft 登陆艇large tank and sphere 大型油罐和球罐launch 发射，下水launching equipment（向水中）投放设备launching way (船舶)下水滑道 LCC(Large Crude Carrier）大型原油轮（载重10~20万吨）lead time 设计至投产、定货至交货的时间 legislation 立法length between perpendicular 两柱间长leveler 调平器，矫平机，矫直机life saving appliance 救生设备 life-cycle cost 生命周期成本lift fan 升力风扇lift offsets 量取型值Light ship weight 空船重量 lighter 港驳船likely 多半，可能line 型线liner 定期航班船liner trade 定期班轮营运业lines plan 型线图liquefied gas carrier 液化气运输船list 倾斜, 表living and utility spaces 居住与公用舱室Lloyd’s Machinery Certificate (LMC) 劳埃德(船舶)机械证书Lloyd’s Register of Shipping (英国)劳埃德船级社Lloyds Rules 劳埃德(船级社)规范LNG containment 液化天然气容器Load Line Regulation 载重线公约、规范load waterline 载重水线load waterplane 载重水线面loft floor 放样台full scale 全尺度loftman 放样工loftman 放样工longitudinal 纵向的longitudinal 纵向的，纵梁longitudinal prismatic coefficient 纵向棱形系数machinery vendor 机械(主机)卖方magnet gantry 磁力式龙门吊maiden voyage 处女航main shafting 主轴系major ship 大型船舶maneuverability 操纵性maritime 海事的，海运的，靠海的，沿海的mark out 划线，划记号marshal 调度mast 桅杆maximum beam amidships 舯最大宽member 部件merchant ship 商船metacenter 稳心metacentric height 稳心高metal plate bath 金属板电镀槽metal worker 金属工metric unit 公制单位midbody （船）中体middle line plane 中线面midship area coefficient 舯横剖面系数midship section 舯横剖面midship section coefficient 舯横剖面系数mill shape 轧钢厂型材module assembly 模块式组装mold loft floor (型线)放样间地板molded lines 型线molder 造型工mould loft 放样间moulded line 型线multihull vessel 多体船Multi-ship program 多种船型建造规划nautical mile 海里naval architect 造船师naval architecture 造船工程naval ship 军船naval architecture 造船学nearuniversal gear 准万向齿轮network flow 网络流程neutral equilibrium 中性平衡normal 法向，法向的，正交的normal force 法向力normal operating condition 常规(正常)运作工况notch 开槽，开凹口Off the shelf 成品的，畅销的，流行的off-center loading 偏移中心的装载offsets 型值offshore drilling 离岸钻井oil-rig 钻油架operational requirement 军事行动需求，运作要求orient 取向，定方位，调整orthogonal 正交的，矩形的out strake 外列板outboard profile 侧视图outfit 舾装outfitter 舾装工outfitting 舾装overall stability 总体稳性overhang 外悬overstocking 存货过剩owner’s staff 船东的雇(职)员paint priming 涂底漆Panama Canal 巴拿马运河panel line system 板材生产线系统parallel middle body 平行中体patternmaker 木模工payload 有效载荷permanent body 永久性组织机构perpendicular（船艏、艉）柱，垂直的，正交的pillar 支柱pin 钉，销pin jig 限位胎架pintle 销，枢轴pipe fitter 管装工pipe laying barge (海底) 铺管驳船piping 管路pitch 纵摇plan views 设计图planing hull 滑行船体pleasure ship 游乐用船Plimsoll line 普林索尔载重线polar-exploration craft 极地考察船Polaris (submarine) 北极星级(潜艇)port 左舷portable gate 移动式(可移动)闸门positive righting arm 扶正力臂power and lighting system 动力与照明系统preliminary design 初步设计preliminary/concept design 初步/概念设计pressure vessel 压力容器principal dimensions 主尺度prism 棱柱体prismatic coefficient 棱形系数procurement 采购，获得Program Evaluation and Review Technique 规划评估与复核法quartering sea 尾斜浪, 从船斜后方来的浪quay(横)码头，停泊所racking 倾斜，变形，船体扭转变形radiography X射线照相术，X射线探伤rake 倾角,倾斜ram pressure 速压头，冲压，全压力rectangle 矩形reenlistment 重征服役Registo Italiano Navale (意大利)船级社remedial action 补救措施reserve buoyancy 储备浮力reserve buoyancy 储备浮力residuary resistance 剩余阻力resultant 合力resultant 合力retract 收进revolving crane 旋转式(鹤)吊，转臂吊(车)Reynolds number 雷诺数rigger 索具装配工rigid side walls 刚性侧壁rise of floor 底升risk 保险对象，保险金额rivering warfare vessel 内河舰艇rivet 铆接，铆钉roll 横摇rolled angle butt (轧制)角钢焊接头roll-on/roll-off(RO-RO) 滚装rough sea 汹涌的波浪round of beam 梁拱rounded gunwale 修园的舷边rubber tile 橡皮瓦rudder post 舵柱rudder 舵rudder rate 舵率rudder stock 舵杆run 去流段Sag 中垂sagging 中垂scale 缩尺，尺度，尺scale model 缩尺船模scantling 材积sea keeping performance 耐波性能seasickness 晕船seaworthiness 适航性section 剖面，横剖面sections (铁、钢)型材，轧材self-induced 自身诱导的semi finished item 半精加工件semisubmersible drilling rig 半潜式钻井架set course 设定的航线set course 设定航线shaft bossing 轴包套shaft bracket 轴支架shear 剪切，剪力sheer aft 艉舷弧sheer forward 艏舷弧sheer drawing 剖面图sheer plane 纵剖面sheer profile 纵剖线sheer profile 纵剖图sheer(甲板)舷弧sheet metal work 钣金工，冷作工shell plating 船壳板shell 船壳板ship fitter 船舶装配工ship fitter 船体安装工ship fitter 舰船装配工ship form 船型ship Hydrodynamics 水动力学ship owner 船东shipping line 船运航线shipway (造)船台shipwright 船体装配工，造船工人shipyard 船厂shipyard 船厂shipyard schedule chart 船厂施工进度图shoring 支撑，支柱shoulder 船肩sideways 朝侧向six degrees of freedom 六自由度sizable 相当大的skirt（气垫船）围裙slamming 砰击，拍击slice 一部分，薄片sloping shipway 有坡度船台，滑道soft chine 圆舭spare part 备件specially prepared form 专门(特殊)加工的模板spectrum 谱speed-to-length ratio 速长比stability 稳性stable equilibrium 稳定平衡standard 规章starboard 右舷static equilibrium 静平衡statically determinant 静定的statistical 统计学(上)的steel marking 钢板划线steering gear 操纵装置steering gear 操纵装置，舵机stem 船艏stem contour 艏柱型线stern 艉stern frame 艉构架，艉框架stern wave 艉波stiffen 加劲，加强stiffener 肋骨strain 应变strake 船体列板stringent safety regulations 严格的安全规章structural alignment 结构校准，组合，组装strut 支柱，支撑构形subassembly (局部)分部装配subdivision 分舱sublet 转包，分包，转租submersible 潜器suction cup 吸盘Suez Canal Tonnage 苏伊士运河吨位限制summer load water line 夏季载重水线super cavitating propeller超空泡螺旋桨superintendent 监督管理人，总段长，车间主任superstructure 上层建筑supertanker 超级油轮supervision of the Society’s surveyor 船级社验船师的监造surface piercing 穿透水面的surface preparation and coating 表面加工处理与喷涂surge 纵荡surmount 顶上覆盖，越过survivability 生存力SWATCH(Small Waterplane Area Twin Hull) 小水线面双体船sway 横荡switchboard 控制台，开关板tabular freeboard 列成表格的干舷值tacker 定位搭焊工talking paper 讨论文件tangential viscous force 切向粘性力tanker 油轮tanker 油轮tantamount 等值的，相当的taper 弄细，变尖tee T形构件，三通管template 样板tensile stress 拉(张)应力The Register of Shipping of the People’s Republic of China 中国船舶检验局The Titanic 泰克尼克号(巨型邮轮)there is more shape to the shell 船壳板的形状较复杂titanic 巨大的to be craft oriented 与行业有关的，适应于行业性的to run the waterlines 绘制水线toed towards amidships 趾部朝向船舯ton gross=gross ton 长吨=1. 016公吨tonnage 吨位torque 扭矩torsio 扭转的trade 工种, 贸易trailer type transporter 拖车式载运车transfer sideways 横向移动transom (stern) 方尾transverse 横向的transverse bulkhead plating 横隔舱壁板transverse section 横剖面transverse stability 横稳性trawling 拖网trial 实船试验trim 纵倾trim 纵倾trim by the stern/bow 艉/艏倾trimaran 三体船trough 波谷tugboat 拖船tumble home(船侧)内倾Type A ship A类船U form U型U. S. Coast Guard 美国海岸警卫队ULCC(Ultra Large Crude Carrier）超级大型原油轮（载重量>40万吨）ultrasonic 超声波的\underwriter (海运)保险商undock 使船出坞upright position 正浮位置V shaped V型的ventilation and air conditioning diagram 通风与空调敷设设计图vertical prismatic coefficient 垂向棱形系数vertical prismatic coefficient 垂向棱形系数vicinity 邻近，附近villain 坏人，罪魁viscosity 粘性VLCC(Very Large Crude Carrier）巨型（原）油轮（载重量>20万吨）V-sectionV型剖面wash 下洗 ,艉流water line 水线waterborne 浮于水上的，水基的waterplane 水线面waterplane area coefficient 水线面积系数watertight integrity 水密完整性wave pattern 波型wavemaking resistance 兴波阻力weather deck 露天甲板weld inspection 焊缝检测welder 焊工weldment 焊件，焊接装配wetted surface 湿面积wing shaft 侧轴yacht 快艇yard issue 船厂开工任务发布书yaw 艏摇yaw 艏摇，摇艏。