FRC1BC-2ANS-DC12V中文资料

FRC系列交直流分压器使用说明书武汉华特电力新技术有限公司目录一、产品用途：．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．（2）二、产品标准：．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．（2）三、产品技术指标：．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．（2）四、产品规格：．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．（2）五、产品操作使用方法：．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．（3）六、产品注意事项：．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．（3）七、产品成套：．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．（4）八、贮存及运输：．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．（4）九、仪器保修：．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．（4）一、产品用途:数字高压表主要用于交流和直流高电压测量。

它通过测量电缆将经过分压后的低压测量信号送到专用数字表中．可以直读交流或直流高电压，本公司制造的数字高压表经过国家高电压计量站型式试验。

二、产品参照标准:DL 474.l～6—92《现场绝缘试验实施导则》ZBF24002《现场直流和交流耐压试验电压测量装置的使用导则》三、产品技术指标:1．准确度：1％2．分压比K=高压／低压=1000:1（所测量高压值=1000×低压表中的值）。

3．电气强度：1.2倍额定电压4．环境条件：温度-4～40℃，湿度：低于85％5．交流电容500PF，直流电阻400兆欧。

四、产品规格:其它规格可按要求生产, 分压器外形如下所示：五、产品操作使用方法:1．将分压器底座，均压罩及本体连接好。

LF00AB/C SERIESVERY LOW DROPVOLTAGE REGULATORS WITH INHIBITJuly 1999s VERY LOW DROPOUT VOLTAGE (0.45V)sVERY LOW QUIESCENT CURRENT(TYP.50µA IN OFF MODE,500µA IN ON MODE)s OUTPUT CURRENT UP TO 500mA sLOGIC-CONTROLLED ELECTRONIC SHUTDOWNsOUTPUT VOLTAGESOF 1.25;1.5;1.8;2.5;2.7;3;3.3;3.5;4;4.5;4.7;5;5.2;5.5;6;8;8.5;9;12Vs INTERNAL CURRENT AND THERMAL LIMIT s ONLY 2.2µF FOR STABILITYsAVAILABLEIN ±1%(AB)OR ±2%(C)SELECTIONAT 25o CsSUPPLY VOLTAGE REJECTION:80db (TYP.)sTEMPERATURE RANGE:-40TO 125o CDESCRIPTIONThe LF00series are very Low Drop regulators available in PENTAWATT,TO-220,ISOWATT220,DPAK and PPAK package and in a wide range of output voltages.The very Low Drop voltage (0.45V)and the very low quiescent current make them particularly suitable for Low Noise,Low Power applications and specially in battery powered systems.In the 5pins configuration (PENTAWATT and PPAK)a Shutdown Logic Control function is available (pin 2,TTL compatible).This means that when the device is used as a local regulator,it is possible to put a part of the board in standby,decreasing the total power consumption.In the three terminal configuration the device has the same electrical performance,but is fixed inSCHEMATIC DIAGRAMPPAK DPAKPENTAWATTTO-220ISOWATT220®1/32ABSOLUTE MAXIMUM RATINGSSymbol Parameter Value Unit V i DC Input Voltage-0.5to40(*)VI o Output Current Internally limitedP tot Power Dissipation Internally limitedT st g Storage Temperature Range-40to150o C T op Operating Junction Temperature Range-40to125o C (*)For18<V IN<40the regulator is in shut-downTHERMAL DATASymbol Parameter PENTAWATT TO-220ISOWATT220DPAK/PPAK UnitR thj-ca se R thj-amb Thermal Resistance Junction-caseThermal Resistance Junction-ambient3503504608100o C/Wo C/WCONNECTION DIAGRAM(top view)PENTAWATTTO-220ISOWATT220PPAK DPAK LF00AB/C2/32ORDERING NUMBERSType PENTAWATT TO-220ISOWATT220DPAK PPAK OutputVoltageLF12C(*) LF12AB(*) LF15C(*) LF15AB(*) LF18CLF18AB LF25CLF25AB LF27CLF27AB LF30CLF30AB LF33CLF33AB LF35CLF35AB LF40CLF40AB LF45C(*) LF45AB(*) LF47CLF47AB LF50CLF50AB LF52CLF52AB LF55CLF55AB LF60CLF60AB LF80CLF80AB LF85CLF85AB LF90CLF90AB LF120C LF120AB 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.25V1.25V1.5V1.5V1.8V1.8V2.5V2.5V2.7V2.7V3V3V3.3V3.3V3.5V3.5V4V4V4.5V4.5V4.75V4.75V5V5V5.2V5.2V5.5V5.5V6V6V8V8V8.5V8.5V9V9V12V12VTEST CIRCUITSLF00AB/C3/32ELECTRICAL CHARACTERISTICS FOR LF12AB(refer to the test circuits,T j=25o C,C i=0.1µF,C o=2.2µF unless otherwise specified)Symbol Parameter Test Conditions Min.Typ.Max.UnitV o Output Voltage I o=50mA,V i=3.3VI o=50mA,V i=3.3V-25<T a<85o C 1.2381.2251.25 1.2631.275VVV i Operating Input Voltage I o=500mA 2.516V I o ut Output Current Limit1A ∆V o Line Regulation V i=2.5to16V,I o=5mA210mV ∆V o Load Regulation V i=2.8V I o=5to500mA210mV I d Quiescent Current ON MODEV i=2.5to16V I o=0mA V i=2.6to16V I o=500mA 0.5112mAmAOFF MODE V i=6V50100µA SVR Supply Voltage Rejection I o=5mA V i=3.5V±1Vf=120Hz f=1KHz f=10KHz 827765dBdBdBeN Output Noise Voltage B=10Hz to100KHz50µV V d Dropout Voltage I o=200mA 1.25V V il Control Input Logic Low-40<T a<125o C0.8V V ih Control Input Logic High-40<T a<125o C2VI i Control Input Current V i=6V,V c=6V10µAC O Output Bypass Capacitance ESR=0.1to10ΩI o=0to500mA210µF ELECTRICAL CHARACTERISTICS FOR LF12C(refer to the test circuits,T j=25o C,C i=0.1µF,C o=2.2µF unless otherwise specified)Symbol Parameter Test Conditions Min.Typ.Max.UnitV o Output Voltage I o=50mA,V i=3.3VI o=50mA,V i=3.3V-25<T a<85o C 1.2251.21.25 1.2751.3VVV i Operating Input Voltage I o=500mA 2.516V I o ut Output Current Limit1A ∆V o Line Regulation V i=2.5to16V,I o=5mA210mV ∆V o Load Regulation V i=2.8V I o=5to500mA210mV I d Quiescent Current ON MODEV i=2.5to16V I o=0mA V i=2.6to16V I o=500mA 0.5112mAmAOFF MODE V i=6V50100µA SVR Supply Voltage Rejection I o=5mA V i=3.5V±1Vf=120Hz f=1KHz f=10KHz 827765dBdBdBeN Output Noise Voltage B=10Hz to100KHz50µV V d Dropout Voltage I o=200mA 1.25V V il Control Input Logic Low-40<T a<125o C0.8V V ih Control Input Logic High-40<T a<125o C2VI i Control Input Current V i=6V,V c=6V10µAC O Output Bypass Capacitance ESR=0.1to10ΩI o=0to500mA210µF LF00AB/C4/32ELECTRICAL CHARACTERISTICS FOR LF15AB(refer to the test circuits,T j=25o C,C i=0.1µF,C o=2.2µF unless otherwise specified)Symbol Parameter Test Conditions Min.Typ.Max.UnitV o Output Voltage I o=50mA,V i=3.5VI o=50mA,V i=3.5V-25<T a<85o C 1.4851.4701.5 1.5151.530VVV i Operating Input Voltage I o=500mA 2.516V I o ut Output Current Limit1A ∆V o Line Regulation V i=2.5to16V,I o=5mA210mV ∆V o Load Regulation V i=2.8V I o=5to500mA210mV I d Quiescent Current ON MODEV i=2.5to16V I o=0mA V i=2.8to16V I o=500mA 0.5112mAmAOFF MODE V i=6V50100µA SVR Supply Voltage Rejection I o=5mA V i=3.5V±1Vf=120Hz f=1KHz f=10KHz 827765dBdBdBeN Output Noise Voltage B=10Hz to100KHz50µV V d Dropout Voltage I o=200mA1V V il Control Input Logic Low-40<T a<125o C0.8V V ih Control Input Logic High-40<T a<125o C2VI i Control Input Current V i=6V,V c=6V10µAC O Output Bypass Capacitance ESR=0.1to10ΩI o=0to500mA210µF ELECTRICAL CHARACTERISTICS FOR LF15C(refer to the test circuits,T j=25o C,C i=0.1µF,C o=2.2µF unless otherwise specified)Symbol Parameter Test Conditions Min.Typ.Max.UnitV o Output Voltage I o=50mA,V i=3.5VI o=50mA,V i=3.5V-25<T a<85o C 1.471.441.5 1.531.56VVV i Operating Input Voltage I o=500mA 2.516V I o ut Output Current Limit1A ∆V o Line Regulation V i=2.5to16V,I o=5mA210mV ∆V o Load Regulation V i=2.8V I o=5to500mA210mV I d Quiescent Current ON MODEV i=2.5to16V I o=0mA V i=2.8to16V I o=500mA 0.5112mAmAOFF MODE V i=6V50100µA SVR Supply Voltage Rejection I o=5mA V i=3.5V±1Vf=120Hz f=1KHz f=10KHz 827765dBdBdBeN Output Noise Voltage B=10Hz to100KHz50µVV d Dropout Voltage I o=200mA1VV il Control Input Logic Low-40<T a<125o C0.8VV ih Control Input Logic High-40<T a<125o C2VI i Control Input Current V i=6V,V c=6V10µAC O Output Bypass Capacitance ESR=0.1to10ΩI o=0to500mA210µFLF00AB/C5/32ELECTRICAL CHARACTERISTICS FOR LF18AB(refer to the test circuits,T j=25o C,C i=0.1µF,C o=2.2µF unless otherwise specified)Symbol Parameter Test Conditions Min.Typ.Max.UnitV o Output Voltage I o=50mA,V i=3.3VI o=50mA,V i=3.3V-25<T a<85o C 1.7821.7641.8 1.8181.836VVV i Operating Input Voltage I o=500mA316V I o ut Output Current Limit1A ∆V o Line Regulation V i=2.8to16V,I o=5mA212mV ∆V o Load Regulation V i=3.3V I o=5to500mA210mV I d Quiescent Current ON MODEV i=2.5to16V I o=0mA V i=3.1to16V I o=500mA 0.5112mAmAOFF MODE V i=6V50100µA SVR Supply Voltage Rejection I o=5mA V i=3.5V±1Vf=120Hz f=1KHz f=10KHz 827760dBdBdBeN Output Noise Voltage B=10Hz to100KHz50µV V d Dropout Voltage I o=200mA0.7V V il Control Input Logic Low-40<T a<125o C0.8V V ih Control Input Logic High-40<T a<125o C2VI i Control Input Current V i=6V,V c=6V10µAC O Output Bypass Capacitance ESR=0.1to10ΩI o=0to500mA210µF ELECTRICAL CHARACTERISTICS FOR LF18C(refer to the test circuits,T j=25o C,C i=0.1µF,C o=2.2µF unless otherwise specified)Symbol Parameter Test Conditions Min.Typ.Max.UnitV o Output Voltage I o=50mA,V i=3.5VI o=50mA,V i=3.5V-25<T a<85o C 1.7641.7281.8 1.8361.872VVV i Operating Input Voltage I o=500mA316V I o ut Output Current Limit1A ∆V o Line Regulation V i=2.8to16V,I o=5mA212mV ∆V o Load Regulation V i=3.3V I o=5to500mA210mV I d Quiescent Current ON MODEV i=2.5to16V I o=0mA V i=3.1to16V I o=500mA 0.5112mAmAOFF MODE V i=6V50100µA SVR Supply Voltage Rejection I o=5mA V i=3.5V±1Vf=120Hz f=1KHz f=10KHz 827760dBdBdBeN Output Noise Voltage B=10Hz to100KHz50µV V d Dropout Voltage I o=200mA0.7V V il Control Input Logic Low-40<T a<125o C0.8V V ih Control Input Logic High-40<T a<125o C2VI i Control Input Current V i=6V,V c=6V10µAC O Output Bypass Capacitance ESR=0.1to10ΩI o=0to500mA210µF LF00AB/C6/32ELECTRICAL CHARACTERISTICS FOR LF25AB(refer to the test circuits,T j=25o C,C i=0.1µF,C o=2.2µF unless otherwise specified)Symbol Parameter Test Conditions Min.Typ.Max.UnitV o Output Voltage I o=50mA,V i=4.5VI o=50mA,V i=4.5V-25<T a<85o C 2.4752.4502.5 2.5252.550VVV i Operating Input Voltage I o=500mA16V I o ut Output Current Limit1A ∆V o Line Regulation V i=3.5to16V,I o=5mA212mV ∆V o Load Regulation V i=3.8V I o=5to500mA212mV I d Quiescent Current ON MODEV i=3.5to16V I o=0mA V i=3.8to16V I o=500mA 0.5112mAmAOFF MODE V i=6V50100µA SVR Supply Voltage Rejection I o=5mA V i=4.5V±1Vf=120Hz f=1KHz f=10KHz 827765dBdBdBeN Output Noise Voltage B=10Hz to100KHz50µVV d Dropout Voltage I o=200mAI o=500mA 0.200.400.350.70VVV il Control Input Logic Low-40<T a<125o C0.8V V ih Control Input Logic High-40<T a<125o C2VI i Control Input Current V i=6V,V c=6V10µAC O Output Bypass Capacitance ESR=0.1to10ΩI o=0to500mA210µF ELECTRICAL CHARACTERISTICS FOR LF25C(refer to the test circuits,T j=25o C,C i=0.1µF,C o=2.2µF unless otherwise specified)Symbol Parameter Test Conditions Min.Typ.Max.UnitV o Output Voltage I o=50mA,V i=4.5VI o=50mA,V i=4.5V-25<T a<85o C 2.452.42.5 2.552.6VVV i Operating Input Voltage I o=500mA16V I o ut Output Current Limit1A ∆V o Line Regulation V i=3.5to16V,I o=5mA212mV ∆V o Load Regulation V i=3.8V I o=5to500mA212mV I d Quiescent Current ON MODEV i=3.5to16V I o=0mA V i=3.8to16V I o=500mA 0.5112mAmAOFF MODE V i=6V50100µA SVR Supply Voltage Rejection I o=5mA V i=4.5V±1Vf=120Hz f=1KHz f=10KHz 827765dBdBdBeN Output Noise Voltage B=10Hz to100KHz50µVV d Dropout Voltage I o=200mAI o=500mA 0.20.40.350.7VVV il Control Input Logic Low-40<T a<125o C0.8VV ih Control Input Logic High-40<T a<125o C2VI i Control Input Current V i=6V,V c=6V10µAC O Output Bypass Capacitance ESR=0.1to10ΩI o=0to500mA210µFLF00AB/C7/32ELECTRICAL CHARACTERISTICS FOR LF27AB(refer to the test circuits,T j=25o C,C i=0.1µF,C o=2.2µF unless otherwise specified)Symbol Parameter Test Conditions Min.Typ.Max.UnitV o Output Voltage I o=50mA,V i=4.7VI o=50mA,V i=4.7V-25<T a<85o C 2.6732.6462.7 2.7272.754VVV i Operating Input Voltage I o=500mA16V I o ut Output Current Limit1A ∆V o Line Regulation V i=3.7to16V,I o=5mA213mV ∆V o Load Regulation V i=4V I o=5to500mA213mV I d Quiescent Current ON MODEV i=3.7to16V I o=0mA V i=4to16V I o=500mA 0.5112mAmAOFF MODE V i=6V50100µA SVR Supply Voltage Rejection I o=5mA V i=4.7V±1Vf=120Hz f=1KHz f=10KHz 827765dBdBdBeN Output Noise Voltage B=10Hz to100KHz50µVV d Dropout Voltage I o=200mAI o=500mA 0.20.40.350.7VVV il Control Input Logic Low-40<T a<125o C0.8V V ih Control Input Logic High-40<T a<125o C2VI i Control Input Current V i=6V,V c=6V10µAC O Output Bypass Capacitance ESR=0.1to10ΩI o=0to500mA210µF ELECTRICAL CHARACTERISTICS FOR LF27C(refer to the test circuits,T j=25o C,C i=0.1µF,C o=2.2µF unless otherwise specified)Symbol Parameter Test Conditions Min.Typ.Max.UnitV o Output Voltage I o=50mA,V i=4.7VI o=50mA,V i=4.7V-25<T a<85o C 2.6462.5922.7 2.7542.808VVV i Operating Input Voltage I o=500mA16V I o ut Output Current Limit1A ∆V o Line Regulation V i=3.7to16V,I o=5mA213mV ∆V o Load Regulation V i=4V I o=5to500mA213mV I d Quiescent Current ON MODEV i=3.7to16V I o=0mA V i=4to16V I o=500mA 0.5112mAmAOFF MODE V i=6V50100µA SVR Supply Voltage Rejection I o=5mA V i=4.7V±1Vf=120Hz f=1KHz f=10KHz 827765dBdBdBeN Output Noise Voltage B=10Hz to100KHz50µVV d Dropout Voltage I o=200mAI o=500mA 0.20.40.350.7VVV il Control Input Logic Low-40<T a<125o C0.8V V ih Control Input Logic High-40<T a<125o C2VI i Control Input Current V i=6V,V c=6V10µAC O Output Bypass Capacitance ESR=0.1to10ΩI o=0to500mA210µF LF00AB/C8/32ELECTRICAL CHARACTERISTICS FOR LF30AB(refer to the test circuits,T j=25o C,C i=0.1µF,C o=2.2µF unless otherwise specified)Symbol Parameter Test Conditions Min.Typ.Max.UnitV o Output Voltage I o=50mA,V i=5VI o=50mA,V i=5V-25<T a<85o C 2.9702.9403 3.0303.060VVV i Operating Input Voltage I o=500mA16V I o ut Output Current Limit1A ∆V o Line Regulation V i=4to16V,I o=5mA315mV ∆V o Load Regulation V i=4.3V I o=5to500mA315mV I d Quiescent Current ON MODEV i=4to16V I o=0mA V i=4.3to16V I o=500mA 0.5112mAmAOFF MODE V i=6V50100µA SVR Supply Voltage Rejection I o=5mA V i=5V±1Vf=120Hz f=1KHz f=10KHz 817665dBdBdBeN Output Noise Voltage B=10Hz to100KHz50µVV d Dropout Voltage I o=200mAI o=500mA 0.20.40.350.7VVV il Control Input Logic Low-40<T a<125o C0.8V V ih Control Input Logic High-40<T a<125o C2VI i Control Input Current V i=6V,V c=6V10µAC O Output Bypass Capacitance ESR=0.1to10ΩI o=0to500mA210µF ELECTRICAL CHARACTERISTICS FOR LF30C(refer to the test circuits,T j=25o C,C i=0.1µF,C o=2.2µF unless otherwise specified)Symbol Parameter Test Conditions Min.Typ.Max.UnitV o Output Voltage I o=50mA,V i=5VI o=50mA,V i=5V-25<T a<85o C 2.942.883 3.063.12VVV i Operating Input Voltage I o=500mA16V I o ut Output Current Limit1A ∆V o Line Regulation V i=4to16V,I o=5mA315mV ∆V o Load Regulation V i=4.3V I o=5to500mA315mV I d Quiescent Current ON MODEV i=4to16V I o=0mA V i=4.3to16V I o=500mA 0.5112mAmAOFF MODE V i=6V50100µA SVR Supply Voltage Rejection I o=5mA V i=5V±1Vf=120Hz f=1KHz f=10KHz 817665dBdBdBeN Output Noise Voltage B=10Hz to100KHz50µVV d Dropout Voltage I o=200mAI o=500mA 0.20.40.350.7VVV il Control Input Logic Low-40<T a<125o C0.8VV ih Control Input Logic High-40<T a<125o C2VI i Control Input Current V i=6V,V c=6V10µAC O Output Bypass Capacitance ESR=0.1to10ΩI o=0to500mA210µFLF00AB/C9/32ELECTRICAL CHARACTERISTICS FOR LF33AB(refer to the test circuits,T j=25o C,C i=0.1µF,C o=2.2µF unless otherwise specified)Symbol Parameter Test Conditions Min.Typ.Max.UnitV o Output Voltage I o=50mA,V i=5.3VI o=50mA,V i=5.3V-25<T a<85o C 3.2673.2343.3 3.3333.366VVV i Operating Input Voltage I o=500mA16V I o ut Output Current Limit1A ∆V o Line Regulation V i=4.3to16V,I o=5mA316mV ∆V o Load Regulation V i=4.6V I o=5to500mA316mV I d Quiescent Current ON MODEV i=4.3to16V I o=0mA V i=4.6to16V I o=500mA 0.5112mAmAOFF MODE V i=6V50100µA SVR Supply Voltage Rejection I o=5mA V i=5.3V±1Vf=120Hz f=1KHz f=10KHz 807565dBdBdBeN Output Noise Voltage B=10Hz to100KHz50µVV d Dropout Voltage I o=200mAI o=500mA 0.20.40.350.7VVV il Control Input Logic Low-40<T a<125o C0.8V V ih Control Input Logic High-40<T a<125o C2VI i Control Input Current V i=6V,V c=6V10µAC O Output Bypass Capacitance ESR=0.1to10ΩI o=0to500mA210µF ELECTRICAL CHARACTERISTICS FOR LF33C(refer to the test circuits,T j=25o C,C i=0.1µF,C o=2.2µF unless otherwise specified)Symbol Parameter Test Conditions Min.Typ.Max.UnitV o Output Voltage I o=50mA,V i=5.3VI o=50mA,V i=5.3V-25<T a<85o C 3.2343.1683.3 3.3663.432VVV i Operating Input Voltage I o=500mA16V I o ut Output Current Limit1A ∆V o Line Regulation V i=4.3to16V,I o=5mA316mV ∆V o Load Regulation V i=4.6V I o=5to500mA316mV I d Quiescent Current ON MODEV i=4.3to16V I o=0mA V i=4.6to16V I o=500mA 0.5112mAmAOFF MODE V i=6V50100µA SVR Supply Voltage Rejection I o=5mA V i=5.3V±1Vf=120Hz f=1KHz f=10KHz 807565dBdBdBeN Output Noise Voltage B=10Hz to100KHz50µVV d Dropout Voltage I o=200mAI o=500mA 0.20.40.350.7VVV il Control Input Logic Low-40<T a<125o C0.8V V ih Control Input Logic High-40<T a<125o C2VI i Control Input Current V i=6V,V c=6V10µAC O Output Bypass Capacitance ESR=0.1to10ΩI o=0to500mA210µF LF00AB/C10/32ELECTRICAL CHARACTERISTICS FOR LF35AB(refer to the test circuits,T j=25o C,C i=0.1µF,C o=2.2µF unless otherwise specified)Symbol Parameter Test Conditions Min.Typ.Max.UnitV o Output Voltage I o=50mA,V i=5.5VI o=50mA,V i=5.5V-25<T a<85o C 3.4653.4303.5 3.5353.570VVV i Operating Input Voltage I o=500mA16V I o ut Output Current Limit1A ∆V o Line Regulation V i=4.5to16V,I o=5mA317mV ∆V o Load Regulation V i=4.8V I o=5to500mA317mV I d Quiescent Current ON MODEV i=4.5to16V I o=0mA V i=4.8to16V I o=500mA 0.5112mAmAOFF MODE V i=6V50100µA SVR Supply Voltage Rejection I o=5mA V i=5.5V±1Vf=120Hz f=1KHz f=10KHz 797460dBdBdBeN Output Noise Voltage B=10Hz to100KHz50µVV d Dropout Voltage I o=200mAI o=500mA 0.20.40.350.7VVV il Control Input Logic Low-40<T a<125o C0.8V V ih Control Input Logic High-40<T a<125o C2VI i Control Input Current V i=6V,V c=6V10µAC O Output Bypass Capacitance ESR=0.1to10ΩI o=0to500mA210µF ELECTRICAL CHARACTERISTICS FOR LF35C(refer to the test circuits,T j=25o C,C i=0.1µF,C o=2.2µF unless otherwise specified)Symbol Parameter Test Conditions Min.Typ.Max.UnitV o Output Voltage I o=50mA,V i=5.5VI o=50mA,V i=5.5V-25<T a<85o C 3.433.363.5 3.573.64VVV i Operating Input Voltage I o=500mA16V I o ut Output Current Limit1A ∆V o Line Regulation V i=4.5to16V,I o=5mA317mV ∆V o Load Regulation V i=4.8V I o=5to500mA317mV I d Quiescent Current ON MODEV i=4.5to16V I o=0mA V i=4.8to16V I o=500mA 0.5112mAmAOFF MODE V i=6V50100µA SVR Supply Voltage Rejection I o=5mA V i=5.5V±1Vf=120Hz f=1KHz f=10KHz 797460dBdBdBeN Output Noise Voltage B=10Hz to100KHz50µVV d Dropout Voltage I o=200mAI o=500mA 0.20.40.350.7VVV il Control Input Logic Low-40<T a<125o C0.8VV ih Control Input Logic High-40<T a<125o C2VI i Control Input Current V i=6V,V c=6V10µAC O Output Bypass Capacitance ESR=0.1to10ΩI o=0to500mA210µF11/32ELECTRICAL CHARACTERISTICS FOR LF40AB(refer to the test circuits,T j=25o C,C i=0.1µF,C o=2.2µF unless otherwise specified)Symbol Parameter Test Conditions Min.Typ.Max.UnitV o Output Voltage I o=50mA,V i=6VI o=50mA,V i=6V-25<T a<85o C 3.9603.9204 4.0404.080VVV i Operating Input Voltage I o=500mA16V I o ut Output Current Limit1A ∆V o Line Regulation V i=5to16V,I o=5mA420mV ∆V o Load Regulation V i=5.3V I o=5to500mA420mV I d Quiescent Current ON MODEV i=5to16V I o=0mA V i=5.3to16V I o=500mA 0.5112mAmAOFF MODE V i=6V50100µA SVR Supply Voltage Rejection I o=5mA V i=6V±1Vf=120Hz f=1KHz f=10KHz 787360dBdBdBeN Output Noise Voltage B=10Hz to100KHz50µVV d Dropout Voltage I o=200mAI o=500mA 0.20.40.350.7VVV il Control Input Logic Low-40<T a<125o C0.8V V ih Control Input Logic High-40<T a<125o C2VI i Control Input Current V i=6V,V c=6V10µAC O Output Bypass Capacitance ESR=0.1to10ΩI o=0to500mA210µF ELECTRICAL CHARACTERISTICS FOR LF40C(refer to the test circuits,T j=25o C,C i=0.1µF,C o=2.2µF unless otherwise specified)Symbol Parameter Test Conditions Min.Typ.Max.UnitV o Output Voltage I o=50mA,V i=6VI o=50mA,V i=6V-25<T a<85o C 3.923.844 4.084.16VVV i Operating Input Voltage I o=500mA16V I o ut Output Current Limit1A ∆V o Line Regulation V i=5to16V,I o=5mA420mV ∆V o Load Regulation V i=5.3V I o=5to500mA420mV I d Quiescent Current ON MODEV i=5to16V I o=0mA V i=5.3to16V I o=500mA 0.5112mAmAOFF MODE V i=6V50100µA SVR Supply Voltage Rejection I o=5mA V i=6V±1Vf=120Hz f=1KHz f=10KHz 787360dBdBdBeN Output Noise Voltage B=10Hz to100KHz50µVV d Dropout Voltage I o=200mAI o=500mA 0.20.40.350.7VVV il Control Input Logic Low-40<T a<125o C0.8V V ih Control Input Logic High-40<T a<125o C2VI i Control Input Current V i=6V,V c=6V10µAC O Output Bypass Capacitance ESR=0.1to10ΩI o=0to500mA210µF 12/32ELECTRICAL CHARACTERISTICS FOR LF45AB(refer to the test circuits,T j=25o C,C i=0.1µF,C o=2.2µF unless otherwise specified)Symbol Parameter Test Conditions Min.Typ.Max.UnitV o Output Voltage I o=50mA,V i=6.5VI o=50mA,V i=6.5V-25<T a<85o C 4.4554.4104.5 4.5454.590VVV i Operating Input Voltage I o=500mA16V I o ut Output Current Limit1A ∆V o Line Regulation V i=5.5to16V,I o=5mA422mV ∆V o Load Regulation V i=5.8V I o=5to500mA422mV I d Quiescent Current ON MODEV i=5.5to16V I o=0mA V i=5.8to16V I o=500mA 0.5112mAmAOFF MODE V i=6V50100µA SVR Supply Voltage Rejection I o=5mA V i=6.5V±1Vf=120Hz f=1KHz f=10KHz 777260dBdBdBeN Output Noise Voltage B=10Hz to100KHz50µVV d Dropout Voltage I o=200mAI o=500mA 0.20.40.350.70VVV il Control Input Logic Low-40<T a<125o C0.8V V ih Control Input Logic High-40<T a<125o C2VI i Control Input Current V i=6V,V c=6V10µAC O Output Bypass Capacitance ESR=0.1to10ΩI o=0to500mA210µF ELECTRICAL CHARACTERISTICS FOR LF45C(refer to the test circuits,T j=25o C,C i=0.1µF,C o=2.2µF unless otherwise specified)Symbol Parameter Test Conditions Min.Typ.Max.UnitV o Output Voltage I o=50mA,V i=6.5VI o=50mA,V i=6.5V-25<T a<85o C 4.414.324.5 4.594.68VVV i Operating Input Voltage I o=500mA16V I o ut Output Current Limit1A ∆V o Line Regulation V i=5.5to16V,I o=5mA422mV ∆V o Load Regulation V i=5.8V I o=5to500mA422mV I d Quiescent Current ON MODEV i=5.5to16V I o=0mA V i=5.8to16V I o=500mA 0.5112mAmAOFF MODE V i=6V50100µA SVR Supply Voltage Rejection I o=5mA V i=6.5V±1Vf=120Hz f=1KHz f=10KHz 777260dBdBdBeN Output Noise Voltage B=10Hz to100KHz50µVV d Dropout Voltage I o=200mAI o=500mA 0.20.40.350.70VVV il Control Input Logic Low-40<T a<125o C0.8VV ih Control Input Logic High-40<T a<125o C2VI i Control Input Current V i=6V,V c=6V10µAC O Output Bypass Capacitance ESR=0.1to10ΩI o=0to500mA210µF13/32ELECTRICAL CHARACTERISTICS FOR LF47AB(refer to the test circuits,T j=25o C,C i=0.1µF,C o=2.2µF unless otherwise specified)Symbol Parameter Test Conditions Min.Typ.Max.UnitV o Output Voltage I o=50mA,V i=6.7VI o=50mA,V i=6.7V-25<T a<85o C 4.6534.6064.7 4.7474.794VVV i Operating Input Voltage I o=500mA16V I o ut Output Current Limit1A ∆V o Line Regulation V i=5.7to16V,I o=5mA423mV ∆V o Load Regulation V i=6V I o=5to500mA423mV I d Quiescent Current ON MODEV i=5.7to16V I o=0mA V i=6to16V I o=500mA 0.5112mAmAOFF MODE V i=6V50100µA SVR Supply Voltage Rejection I o=5mA V i=6.7V±1Vf=120Hz f=1KHz f=10KHz 777260dBdBdBeN Output Noise Voltage B=10Hz to100KHz50µVV d Dropout Voltage I o=200mAI o=500mA 0.20.40.350.7VVV il Control Input Logic Low-40<T a<125o C0.8V V ih Control Input Logic High-40<T a<125o C2VI i Control Input Current V i=6V,V c=6V10µAC O Output Bypass Capacitance ESR=0.1to10ΩI o=0to500mA210µF ELECTRICAL CHARACTERISTICS FOR LF47C(refer to the test circuits,T j=25o C,C i=0.1µF,C o=2.2µF unless otherwise specified)Symbol Parameter Test Conditions Min.Typ.Max.UnitV o Output Voltage I o=50mA,V i=6.7VI o=50mA,V i=6.7V-25<T a<85o C 4.6064.5124.7 4.7944.888VVV i Operating Input Voltage I o=500mA16V I o ut Output Current Limit1A ∆V o Line Regulation V i=5.7to16V,I o=5mA423mV ∆V o Load Regulation V i=6V I o=5to500mA423mV I d Quiescent Current ON MODEV i=5.7to16V I o=0mA V i=6to16V I o=500mA 0.5112mAmAOFF MODE V i=6V50100µA SVR Supply Voltage Rejection I o=5mA V i=6.7V±1Vf=120Hz f=1KHz f=10KHz 777260dBdBdBeN Output Noise Voltage B=10Hz to100KHz50µVV d Dropout Voltage I o=200mAI o=500mA 0.20.40.350.7VVV il Control Input Logic Low-40<T a<125o C0.8V V ih Control Input Logic High-40<T a<125o C2VI i Control Input Current V i=6V,V c=6V10µAC O Output Bypass Capacitance ESR=0.1to10ΩI o=0to500mA210µF 14/32。