MX400SEGooseneck MicrophonesShure MX400SE Series miniature gooseneck-mounted electret condenser microphones online user guide. Version: 5 (2019-J)Table of ContentsMX400SEGooseneck Microphones3 General Description3 Model Variations 3 Interchangeable Cartridges 3 Snap-Fit Windscreen 5 Preamp Gain5RFI Filtering5 Microphone Placement5 Permanent Installation 6 Changing from Side Exit to Bottom Exit 6 Flange 6 Shock Mount 7 Specifications8 Certifications 11••••••••MX400SEGooseneck Microphones General DescriptionShure Microflex MX400SE Series microphones are miniature gooseneck-mounted electret condenser microphones designed primarily for speech and vocal pickup. Their high sensitivity and broad frequency range make them suitable for recording, as well as sound reinforcement applications.The MX400SE series can be screwed onto a mic stand or the supplied 5/8 in. 27-threaded flange. They can be easily changed from side exit to bottom exit to conceal the cabling. All models include an in-line preamplifier, a 3.66 m (12 ft.) cable.Wide dynamic range and frequency response for accurate sound reproductionInterchangeable cartridges that provide a choice of polar pattern for each application Shock mount provides over 20 dB of isolation from surface vibration noise Snap-fit foam windscreen RF filteringModel VariationsMX400 microphones are available with 305 mm (12 in.) or 457 mm (18 in.) goosenecks, with or without a mute switch. They are available in supercardioid, cardioid and omnidirectional polar patterns."S" models include a mute button and LED."D" models include a desktop base with programmable mute button and LED and logic input and output."SE" models feature a surface mount flange with side-exit cable.The polar pattern of the included cartridge is indicated by a model number suffix:/C Cardioid/S Supercardioid /O Omnidirectional/N Cartridge not included®Interchangeable CartridgesMicroflex microphones use interchangeable cartridges that allow you to choose the polar pattern for different installations.•••••••Snap-Fit WindscreenSnap into the groove below the cartridge.To remove, spread the gap with a screwdriver or thumbnail.Provides 30 dB of "pop" protection.Preamp GainIf necessary, the preamplifier gain can be reduced by 12 dB. Contact an authorized Shure service center for information.RFI FilteringImportant: Microphones must be used with the RK100PK or RK202PK plate-mounted preamp to optimize RF immunity.Microphone PlacementAim the microphone toward the desired source, such as the talker.Aim it away from any unwanted source, such as a loudspeaker.Place the microphone within 15 to 30cm (6 to 12 in.) of the desired sound source.Always use the supplied windscreen or optional metal windscreen to control breath noise.•If four or more microphones will be open at the same time, use of an automatic mixer, such as the Shure SCM810 or SCM410, is recommended.Permanent InstallationChanging from Side Exit to Bottom ExitDo not cut the cable to reroute. This will compromise RF immunity.Mount the microphone using one of the following methods.FlangeSlip the mounting flange retaining ring over the bottom of the preamplifier and slide it up until it is flush to the bottom of the flange. Then press the ring firmly into place.1.2.3.4.Shock MountDrill a 44mm(1-3/4 in.) diameter hole in desired mounting surface.Mark and drill starter holes for screws, using shock mount as a template.Secure shock mount to mounting surface with screws.Thread the supplied adapter onto the MX400SE microphone before inserting it into the shock mount.SpecificationsTypeElectret CondenserFrequency Response50 to 17000 HzPolar PatternMX412SE/C, MX418SE/C CardioidMX412SE/S, MX418SE/S SupercardioidOutput Impedance180 ΩOutput ConfigurationActive BalancedSensitivity@ 1 kHz, open circuit voltageCardioid–35 dBV/Pa(18 mV)Supercardioid–34 dBV/Pa(21 mV)1 Pa=94 dB SPLMaximum SPL1 kHz at 1% THD, 1 kΩ loadCardioid124 dBSupercardioid123 dBSelf NoiseA-weightedCardioid28 dB SPLSupercardioid27 dB SPLSignal-to-Noise RatioRef. 94 dB SPL at 1 kHzCardioid66 dBSupercardioid68 dBDynamic Range1 kΩ load, @ 1 kHz96 dBCommon Mode Rejection10 Hz to 100 kHz45 dB, minimumClipping Levelat 1% THD–6 dBV (0.5 V)PolarityPositive sound pressure on diaphragm produces positive voltage on pin 2 relative to pin 3 of output XLR connectorEnvironmental ConditionsOperating Temperature–18–57°C (0–135°F)Storage Temperature–29–74°C (–20–165°F)Relative Humidity0–95%Power Requirements11–52 V DC, 2.0 mACable3.0 m (10 ft) , attachedCertificationsMeets essential requirements of all applicable European Directives.Eligible for CE marking.The CE Declaration of Conformity can be obtained from Shure Incorporated or any of its European representatives. For contact information please visit The CE Declaration of Conformity can be obtained from: /europe/complianceAuthorized European representative:Shure Europe GmbHHeadquarters Europe, Middle East & AfricaDepartment: EMEA ApprovalJakob-Dieffenbacher-Str. 1275031 Eppingen, GermanyPhone: +49-7262-92 49 0Fax: +49-7262-92 49 11 4Email:*************。
SCM810八頻道話筒混音器Shure SCM810 eight-channel microphone mixer user guide Version: 5.1 (2020-K)Table of ContentsSCM810 八頻道話筒混音器3重要安全事項! 3簡要說明3系統功能 4操作原則4前面板功能4後面板功能 5 DIP 開關 6在機架安裝混音器7 SCM810/E 連接 8輸出限制器設定 8等化器功能8透過自動混音器使用等化器/回饋控制器9基本混音器操作9連網多個混音器10全域/本機功能10連結纜線 11備件 11規格12服務聲明14認證14進階功能14 14邏輯連接規格 14建議的邏輯應用15內部修改20 201.2.3.4.5.6.7.8.9.10.11.12.13.14.15.16.17.18.19.20.21.SCM810八頻道話筒混音器重要安全事項!必須閱讀這些注意事項。
必須保留這些注意事項。
必須注意所有警告內容。
必須遵循所有注意事項。
不要在靠近水的地方使用本設備。
只能用幹布擦拭設備。
不要堵塞任何通風口。
留出足夠的距離，確保充分通風，並安裝在符合製造商要求的位置。
不要將本設備安裝在任何熱源（如明火、散熱器、調溫器、火爐或包括功率放大器在可的其它可能產生熱量的裝置附近。
不要將任何明火火源放置在產品上。
不要破壞帶極性或接地類型插頭的安全功能。
極性插頭帶有兩個插片，其中一個比另一個寬。
接地類型插頭帶有兩個插片和第三個接地插腳。
較寬的插片或第三個插腳是為安全目的設定的。
如果提供的插頭無法插入插座，請向電工諮詢如何更換合適的插座。
保護電源線防止被腳踩踏或被夾緊，尤其是在插頭、方便插座和機身電源線的引出處。
只能使用製造商指定的連接部件/附件。
只能使用製造商指定的或隨設備售出的手推車、支座、三角架、托架或支撐台。
如果使用手推車，在移動裝有設備的手推車時應注意安全，避免設備翻落。
在雷電天氣或長時間不使用時，應拔下設備的插頭。
Model 515SBGX, 515SBG-18X and515SBG-18XF User Guide©2006, Shure Incorporated 27E2974 (Rev. 8)Printed in U.S.A.GENERALThe Shure Models 515SBGX, 515SBG-18X, and 515SBG-18XF microphones are low-impedance dynamic microphones designed to be mounted on flexible goosenecks or fixed pips. Optimized fre-quency response and a unidirectional (cardioid) pickup patter makes them ideal for language labs, paging applications, and base station communications. They are also recommended for use as talkback or cuing microphones in TV, film, and recording studios. Because of their low impedance, these microphones retain their level and response characteristics even when long lengths of cable are used.All three models are supplied with a push-to-talk button and a four-conductor cable (two conductors shielded).Features•Frequency response optimized for announcing, narration, and paging applications•Cardioid pickup pattern symmetrical about axis •Neodymium magnet for high signal-to-noise ratio•Shock-mounted cartridge for quiet operation and low stand/han-dling noise•Tough diecast locking grille and handle•Built-in push-to-talk button controls microphone circuit and relay or control circuit•45.7 cm (18 in.) gooseneck and mounting flange supplied (515SBG-18X and 515SBG-18XF only)VARIATIONSMODEL 515SBGX: Does not include gooseneck or mounting flangeMODEL 515SBG-18X: Includes gooseneck and 76.2 mm (3 in.) diameter mounting flangeMODEL 515SBG-18XF: Includes gooseneck and 44.4 mm (1-3/4 in.) diameter mounting flangeSPECIFICATIONSTypeDynamic (moving coil)Frequency Response80 to 15,000 Hz (see Figure 1)TYPICAL FREQUENCY RESPONSEFIGURE 1Polar PatternCardioid (unidirectional). Effective rejection of sound at rear of mi-crophone is uniform at all frequencies, while front pickup charac-teristics are uniform about axis (see Figure 2).FIGURE 2Impedance150 Ω rated (180 Ω actual)Output Level (at 1,000 Hz)Open Circuit Voltage: -57 dBV/Pa* (1.4 mV)*1 PA = 94 DB SPLPhasingPositive pressure on diaphragm produces positive voltage on RED cable relative to BLACK cable lead515SBGX515SBG-18X2SwitchBuilt-in, leaf-type, non-locking, push-to-talk Shock MountInternal rubber vibration isolator CableHighly durable cable with effective hum shielding, four conduc-tors (two shielded), plastic jacketed Model 515SBGX: 1.8 m (70 in.)Models 515SBG-18X and 515SBG-18XF: 1.3 m (51 in.) from gooseneck CaseSilver finish die casting with black enamel diecast grille and stainless steel screen Dimensions See Figure 3OVERALL DIMENSIONSFIGURE 3CertificationConforms to European Union directives, eligible to bear CE marking; meets European Union EMC Immunity Requirements (EN 55103).Net Weight515SBGX......................................................380 g (13.5 oz)515SBG-18X.................................................900 g (31.8 oz)515SBG-18XF...............................................787 g (27.8 oz)FURNISHED ACCESSORIES1.27 mm (.050 in.) Hex Wrench .................................80A6745.75 cm (18 in.)Gooseneck(515SBG-18X, 515SBG-18XF only)...............................G18Flange (515SBG-18X only).......................................A13HD Flange (515SBG-18XF only)..........................................A12REPLACEMENT PARTSCartridge.......................................................................R180Grille Assembly.......................................................RK334G Cable......................................................................70A4063Gooseneck (515SBG-18X, 515SBG-18XF)...................G18Flange (515SBG-18X)...............................................A13HD Flange (515SBG-18XF)..................................................A12Windscreen...............................................................A85WSCONNECTIONSThese low-impedance microphones are designed for connection to microphone inputs rated at 75 to 300 ohms. Using balanced-line low-impedance cables permits very long cable lengths without af-fecting response or level. The RED and BLACK cable leads are the microphone conductors for balanced-line connections; the shield is connected to the amplifier ground.For unbalanced operation, connect the BLACK lead to the shield, and use the RED lead as the microphone conductor.The GREEN and WHITE cable leads are used to control an exter-nal relay or control circuit. Refer to the following table and to the wiring diagram in Figure 4.FIGURE 4MOUNTING THE 515SBG-18X AND 515SBG-18XFMount the 515SBG-18X or 515SBG-18XF as follows:1.Thread the supplied hexnut all the way down on the mountingflange.2.Thread the gooseneck tightly on the flange.3.Back the hexnut up against the gooseneck, and use a wrenchto tighten the nut firmly against the bottom of the gooseneck.MOUNTING THE 515SBX ONTO A GOOSENECKMount the 515SBGX onto a gooseneck or fixed pipe with a 5/8 in-27 thread as follows:1.Unscrew the black end cap from the microphone.2.Remove the thin metal washer and the metal spacer.3.Re-install the washer by sliding it back onto the cable and upinto the end of the microphone.4.Slip the cable into the gooseneck or pipe and thread themicrophone firmly to the mount.For additional service or parts information, please contact Shure's Service department at 1-800-516-2525. Outside the United States, please contact your authorized Shure Service Center.INPUT TYPEWIRE COLOR FUNCTIONXLRCONNECTOR1/4 IN. PHONE PLUG REDAUDIO PIN 2TIP UNBALANCED BLACK AUDIO GROUND PIN 3SLEEVE SHIELD CHASSIS GROUNDPIN 1SLEEVE REDAUDIO +PIN 2TIP BALANCED BLACK AUDIO -PIN 3RING SHIELDCHASSIS GROUNDPIN 1SLEEVESHURE Incorporated United States, Canada, Latin America, Caribbean:5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A.Phone: 847-600-2000 U.S. Fax: 847-600-1212 Intl Fax: 847-600-6446Europe, Middle East, Africa:Shure Europe GmbH, Phone: 49-7131-72140 Fax: 49-7131-721414Asia, Pacific:Shure Asia Limited, Phone: 852-2893-4290 Fax: 852-2893-4055。
MV88plus Stereo USB MicrophoneShure MV88+ 立体声 USB 话筒The Shure digital USB microphone, MV88+ Stereo USB, user guide.Version: 1.0 (2021-J)Table of ContentsMV88plus Stereo USB Microphone Shure MV88+ 立体声USB 话筒3简要说明3产品特点 3快速设置3防风罩 4 MV88+ 话筒4麦克风方向 5 MV88+ 输出 5对准话筒5音频录制 6录音采访（桌面） 6手持式录制 7 Shure MOTIV 桌面应用程序7话筒设置 8预设模式 9定制预设 9指向性选择（立体声和单声道设置） 9监听混音合成11高级话筒设置 11限幅器11压缩器11高通滤波器11左右通道交换11均衡器11流媒体提示12控制音量 12使用锁定模式锁定您的声音 12监听声音 12故障排除12固件更新12在更新过程中保持设备连接 13系统要求13系统要求和兼容性：Mac 13系统要求和兼容性：Windows 13系统要求和兼容性：iOS 13系统要求和兼容性：Android 13规格 13认证15 Information to the user 15•••••••••••MV88plus Stereo USB Microphone Shure MV88+ 立体声 USB 话筒简要说明Shure MV88+ 是一款专业的高品质电容话筒，可通过 Lightning 或 USB-C 接头直接插入到移动设备中。
两个话筒炭精盒按中侧配置排列，提供可调节的立体声声像，适合捕获各种音源，包括音乐和语音。
ShurePlus MOTIV 应用允许您通过数字信号处理(DSP)、预设模式选择、增益调节、压缩和立体声宽度控制来自定义声音。
产品特点Mid-Side 立体声支持经典的 mid-side 立体声录制技术。
