思科第二学期第一章答案

2017C C N A第二学期第一章考试答案解析(总9页)以下是针对您未获得满分的试题给出的反馈。

某些交互式试题可能不显示您的答案。

分项分数：?? ?? ?? ?? ?? ?? ?? ?? ?? ?? ?? ?? ?? ?? ?? ?? ?1 与固定配置的交换机相比，模块化交换机具有哪两个优点（请选择两项。

）正确? 响应? 您的? 响应?每台交换机的成本更低 可扩展性更高 转发率更低需要的电源插座数目更少带宽聚合可以使用多个端口固定配置交换机价格较低，但是它具有指定数量的端口且不能添加端口。

它们提供的高速端口通常比较少。

为了在包含固定配置交换机的网络上扩展交换，需要购买更多的交换机。

这增加了需要使用的电源插座数量。

模块化交换机只需要购买额外的线卡便可以扩展。

带宽聚合也更容易，因为机箱的背板可以为交换机端口线卡提供所需的带宽。

此试题参考以下领域的内容：Routing and Switching Essentials交换网络2 思科无边界架构接入层的基本功能是什么？正确? 响应? 您的? 响应?聚合第 2 层广播域 聚合第 3 层路由边界 为用户提供访问权提供高可用性思科无边界架构接入层的功能是为用户提供网络访问。

第 2 层广播域聚合、第 3 层路由边界聚合和高可用性是分布层的功能。

也有说答案是 聚合第 3 层路由边界此试题参考以下领域的内容：Routing and Switching Essentials融合网络3 思科无边界架构分布层的基本功能是什么？正确? 响应? 您的? 响应?充当主干 聚合所有园区块 聚合第 3 层路由边界为用户提供访问权思科无边界架构的分布层的一项基本功能是在不同的 VLAN 之间路由。

充当主干和聚合园区块是核心层的功能。

为用户提供访问是接入层的功能。

此试题参考以下领域的内容：Routing and Switching Essentials融合网络4若将大端口密度、容错和低价作为重要指标，应使用哪个交换机外形因素？正确? 响应?您的?响应?固定配置交换机模块化交换机可配备机架的1U 交换机可堆叠式交换机堆叠式交换机可以使用特殊电缆实现互联，从而在交换机之间提供高带宽的吞吐量，并像单个大型交换机一样运行。

Close WindowAssessment System 1. Assessment Selection 2. Assessment Settings 3. Take Assessment 1Refer to the exhibit. Which summarization should R1 use to advertise its networks to R2? 192.168.1.0/24 192.168.0.0/24 192.168.0.0/22 192.168.1.0/22 2If a router is booting with its default configuration register setting and its NVRAM lacks boot system commands, from try to load the IOS image first? ROM RAM NVRAM f lash flash TFTP server 3Refer to the exhibit. A network administrator adds this command to router R1: ip route 192.168.2.0 255.255.255.0 S0/0/0. result of adding this command? This route is automatically propagated throughout the network. The traffic for network 172.16.1.0 is forwarded to network 192.168.2.0. A static route is established. A static route is established. The traffic for all Class C networks is forwarded to 172.16.1.2. 4Which two technologies can be used in distance vector routing protocols to prevent routing loops? (Choose two.) authentication link-state advertisements h old-down timers hold-down timers Spanning Tree Protocol split horizon 5Refer to the exhibit. What information can be determined from the displayed output? E IGRP packets are waiting to be sent to the neighbors. EIGRP packets are waiting to be sent to the neighbors. The adjacencies between the routers are yet to be established. The IP address 192.168.10.10 is configured at serial interface S0/0/1 of router R2. Router R2 is receiving hello packets from a neighbor with the IP address 192.168.10.10 via the R2 S0/0/1 interf6Which statement is true about the metrics used by routing protocols? A metric is a value used by a particular routing protocol to compare paths to remote networks. A metric is a value used by a particular routing protocol to compare paths to remote networks. A common metric is used by all routing protocols. The metric with the highest value is installed in the routing table. The router may use only one parameter at a time to calculate the metric. 7Which feature of RIPv2 enables it to function as a classless routing protocol? Subnet masks are included in routing updates. Routing updates are triggered by topology changes. Next-hop addresses are included in routing updates. N ext-hop addresses are included in routing updates. Multicast addresses are used to send routing updates. 8Refer to the exhibit. The hosts on the R1 LAN are unable to access the Internet. What is incorrectly configured? the IP address of the Fa0/0 interface at R1 t he IP address of the Fa0/0 interface at R1 the IP address of the S0/0/1 interface at R2 the IP address of the S0/0/0 interface at R1 the subnet mask of the S0/0/1 interface at R2 9Which prompt is used to allow a user to change the IP address of an interface on a router? Router> R outer> Router# Router(config)# Router(config-if)# 10Refer to the exhibit. The interfaces of all routers are configured for OSPF area 0. R3 can ping R1, but the two routeestablish a neighbor adjacency. What should the network administrator do to troubleshoot this problem? Check if the interfaces of the routers are enabled. Check the hello and dead intervals between the routers. C heck the hello and dead intervals between the routers. Check the process ID of both routers. Check if CDP is enabled on all the routers. 11Refer to the exhibit. Which combination of IP address and subnet mask can be used on the serial interface of Route interface in the same network as the serial interface of Router1? IP 172.16.0.18, subnet mask 255.255.255.0 IP 172.16.32.15, subnet mask 255.255.255.240 I P 172.16.32.15, subnet mask 255.255.255.240 IP 172.16.0.18, subnet mask 255.255.255.252 IP 172.16.32.18, subnet mask 255.255.255.252 12Refer to the exhibit. A network engineer has run the show version command on R3. Upon rebooting, R3 does not load configuration settings. What could be the cause of this problem? There is insufficient NVRAM. There is insufficient flash memory. The configuration register is not configured with the default setting. The system image file is not located in NVRAM. 13Refer to the exhibit. On the basis of the show running-config output, which option correctly reflects the routes that will b routing table? 14Refer to the exhibit. Host A is having problems accessing server A. All routers have the same EIGRP configuration a What should be done so that host A can access server A? Add the command n ono auto-summary on all routers. Change the network statements to include a wildcard mask. Adjust the EIGRP hello timers to account for the network delay. Add the command e igrpeigrp log-neighbor-changes on all routers. 15Refer to the exhibit. The network is running the RIP routing protocol. Network 10.0.0.0 goes down. Which statement is the routers in this topology will respond to this event? Router4 will learn about the failed route 30 seconds later in the next periodic update. Split horizon will prevent Router4 from fowarding packets to the 10.0.0.0 network until the holddown timer expire Router5 immediately flushes the unreachable route from its routing table. Router5 will send Router4 a triggered update with a metric of 16 for network 10.0.0.0. 16A network administrator is in charge of two separate networks that share a single building. What device will be require networks and add a common connection to the Internet that can be shared? hub router access point Ethernet switch E thernet switch 17Refer to the exhibit. A network administrator has configured OSPF using the following command: network 192.168.1.32 0.0.0.31 area 0Which router interface will participate in OSPF? FastEthernet0/0 FastEthernet0/1 Serial0/0/0 Serial0/0/1 18Refer to the exhibit. R1 is configured properly for a single area OSPF, and R2 has been recently installed in the netcommands is required to configure a single area OSPF for the networks that are connected to R2? R2(config)# router ospf 1R2(config-router)# network 192.168.2.0 0.0.0.255 area 0R2(config-router)# network 10.1.1.0 0.0.0.3 area 0R2(config)# router ospf 1R2(config-router)# network 192.168.2.0 0.0.0.255 area 0R2(config)# router ospf 2R2(config-router)# network 10.1.1.0 0.0.0.3 area 0R2(config)# router ospf 1R2(config-router)# network 192.168.2.0 0.0.0.255 area 0R2(config-router)# network 10.1.1.0 0.0.0.3 area 1R2(config)# router ospf 1R2(config-router)# network 192.168.2.0 0.0.0.255 area 0R2(config-router)# network 10.0.0.0 0.0.0.3 area 119Which two statements are true for link-state routing protocols? (Choose two.) Routers that run a link-state protocol can establish a complete topology of the network. Routers in a multipoint network that run a link-state protocol can exchange routing tables. Routers use only hop count for routing decisions. The shortest path first algorithm is used. Split horizon is used to avoid routing loops. 20Which candidate route has the longest match for a packet with a destination address of 10.30.16.48? 10.30.0.0/16 10.30.15.0/23 10.30.16.0/24 10.30.16.32/27 10.30.16.32/30 21Which statement is true about the RIPv1 protocol? It is a link-state routing protocol. It excludes subnet information from the routing updates. It uses the DUAL algorithm to insert backup routes into the topology table. It uses classless routing as the default method on the router. 22Which of the following are primary functions of a router? (Choose two.) packet switching microsegmentation domain name resolution path selection flow control 23Refer to the exhibit. Partial results of the show running-config and s how show ip route commands are displayed. Router B rec with a destination address of 10.16.1.97. What will router B do? drop the packet forward the packet via the route to 10.16.1.0 f orward the packet via the route to 10.16.1.64 forward the packet via the route to 10.16.1.64 use the default route 24 What are two ways that a router can learn of the paths to destination networks? (Choose two.) updates from other routers DHCP information broadcasts m anual configuration of routes manual configuration of routes ARP requests from connected routers inspection of the destination IP address in data packets updates from the SMTP management information base 25Refer to the exhibit. Host A is unable to access the Internet. What is the reason for this? The IP address of host A is incorrect. The default gateway of host A is incorrect. The Fa0/1 interfaces of the two routers are configured for different subnets. T he Fa0/1 interfaces of the two routers are configured for different subnets. The subnet mask for the Fa0/0 interface of R1 is incorrect. 26A network administrator is analyzing routing update behavior on a network that has both EIGRP and OSPF configured protocols appear in the output of show ip protocols. However, only EIGRP internal routes appear in the routing tables. correctly explains the scenario? The OSPF protocol has a higher cost than EIGRP. T he OSPF protocol has a higher cost than EIGRPThe EIGRP protocol has a lower metric than OSPF. The EIGRP protocol was configured first on the router. The EIGRP protocol has a lower administrative distance than OSPF. 27Refer to the exhibit. The network has three connected routers: R1, R2, and R3. The routes of all three routers are d are operational and pings are not blocked on this network. Which ping will fail? from R1 to 172.16.1.1 from R1 to 192.168.3.1 from R2 to 192.168.1.1 from R2 to 192.168.3.1 28Refer to the exhibit. A device is required to complete the connection between router R1 and the WAN. Which two de this? (Choose two.) a CSU/DSU device a modem a n Ethernet switch an Ethernet switch a hub a bridge 29 In which situation would a default static route be recommended? when connecting an edge router to the Internet w hen variable length subnet masking is in effect when variable length subnet masking is in effect when there is more than one valid route for a destination network when a destination network has a larger mask than any routes in the routing table 30 Two routers need to be configured within a single OSPF area. Which two components need to be configured on boththis? (Choose two.) t he same process ID the same process ID the same area ID network addresses and wildcard masks the same router ID the same loop back address 231Refer to the exhibit. What is the meaning of the highlighted value 120? It is the metric that is calculated by the routing protocol. It is the value that is used by the DUAL algorithm to determine the bandwidth for the link. It is the administrative distance of the routing protocol. It is the hold-down time, measured in seconds, before the next update. 32Refer to the exhibit. A router learns a route to the 192.168.6.0 network, as shown in the output of the show ip rip database However, upon running the show ip route command, the network administrator sees that the router has installed a diff command, the network administrator sees that the router has installed a diffe 192.168.6.0 network learned via EIGRP. What could be the reason for the missing RIP route? Compared to RIP, EIGRP has a lower administrative distance. Compared to EIGRP , RIP has a higher metric value for the route. Compared to RIP , the EIGRP route has fewer hops. Compared to RIP , EIGRP has a faster update timer. 33 Which mechanism helps to avoid routing loops by advertising a metric of infinity? route poisoning split horizon hold-down timer triggered updates 34 A network administrator must use the subnet 172.16.128.0/18 to create 6 additional subnets each containing up to 20LANs. Which subnet mask should the administrator use to create the new subnets? 255.255.224.0 255.255.240.0 255.255.248.0 255.255.252.0 35 A technician configures the Fa0/0 interface on a router with ip address 192.168.3.5 255.255.255.252. What additional com. What additional com issued by the technician to activate the interface to forward traffic? Router(config-if)# exitRouter(config-if)# no shutdownRouter(config-if)# clock rateRouter# copy running-config startup-config36 Because of a topology change, the next hop IP address in the current static route must be reconfigured. How can a altered to accommodate a topology change? Keep the existing static route and configure a new static route with the correct next hop IP address. Negate the existing static route and configure a new static route with the correct next hop IP address. D o nothing. The existing static route will automatically update the next hop entry with the new IP address. Do nothing. The existing static route will automatically update the next hop entry with the new IP address. Keep the existing static route, reload the router, and configure a new static route with the correct next hop IP a37Refer to the exhibit. What needs to be done to allow these two routers to connect successfully? Add a clock rate to S0/0/0 on R1. Add an interface description to S0/0/1 on R2. C hange the serial interface on R2 to S0/0/0 so that it matches R1. Change the serial interface on R2 to S0/0/0 so that it matches R1. Change the IP address of S0/0/1 on R2 so that it is in the same subnet as R1. 38Refer to the exhibit. The network administrator has run the following command on R1. R1(config)# ip route 192.168.2.0 255.255.255.0 172.16.1.2What is the result of running this command? Traffic for network 192.168.2.0 is forwarded to 172.16.1.2. This route is automatically propagated throughout the entire network. Traffic for all networks is forwarded to 172.16.1.2. The command invokes a dynamic routing protocol for 192.168.2.0. 39 Why is fast convergence desirable in networks that use dynamic routing protocols? Hosts are unable to access their gateway until the network is converged. Routers will not allow packets to be forwarded until the network is converged. Routers may make incorrect forwarding decisions until the network has converged. Routers will not allow configuration changes to be made until the network has converged. 40Refer to the exhibit. When all of the commands that are shown in the exhibit are entered at the correct router promp the router? name cisco router hostname 41Refer to the exhibit. Packets destined to which two networks will require the router to perform a recursive lookup? (C10.0.0.0/8 64.100.0.0/16 128.107.0.0/16 172.16.40.0/24 192.168.1.0/24 192.168.2.0/24 42Refer to the exhibit. A router interface is configured with the command ip address 172.16.3.31 255.255.192.0. Which set o. Which set o values would allow a computer that is connected to the router interface to communicate with remote networks? A: 172.16.3.254 A: 172.16.3.254 B: 255.255.192.0 C: 172.16.3.31 A: 172.16.3.31 B: 255.255.192.0 C: 172.16.3.255 A: 172.16.3.254 B: 255.255.255.0 C: 172.16.3.31 A: 172.16.3.31 B: 255.255.255.0 C: 172.16.3.1 43Which three statements are true regarding the encapsulation and de-encapsulation of packets when traveling through three.) The router modifies the TTL field, decrementing it by one. The router changes the source IP to the IP of the exit interface. The router maintains the same source and destination IP. The router changes the source physical address to the physical address of the exit interface. The router changes the destination IP to the IP of the exit interface. The router sends the packet out all other interfaces, besides the one it entered the router on. 44Refer to the exhibit. Which three statements are true of the routing table for Router1? (Choose three.) The route to network 172.16.0.0 has an AD of 156160. Network 192.168.0.16 can best be reached using FastEthernet0/0. The AD of EIGRP routes has been manually changed to a value other than the default value. Router1 is running both the EIGRP and OSPF routing process. Network 172.17.0.0 can only be reached using a default route. No default route has been configured. N o default route has been configured. 45Refer to the exhibit. Which route will be installed in the routing table on R1 to forward traffic from PC1 to the web s the static route the route learned via OSPF the route learned via EIGRP both routes learned via OSPF and EIGRP 46Refer to the exhibit. Based on the partial output in the exhibit, why can users establish a console connection to this r a password? The login command was not entered on the console line. The enable password should be an enable secret password. No username and password combination has been configured. Console connections cannot be configured to require users to provide passwords. 47Refer to the exhibit. Which path will traffic from the 172.16.1.0/24 network take to get to the 10.0.0.0/24 network? ADC ABC It will load balance the traffic between ADC and ABC It will send the traffic via ABC, and will use ADC as a backup path only when ABC fails. 48A router learns about network 192.168.10.128/27 from multiple sources. Which option represents the best route and w routing table? S 192.168.10.128/27 [1/0] via 192.168.10.226 R 192.168.10.128/27 [120/2] via 192.168.10.226, 00:00:14, Serial0/0/0 O 192.168.10.128/27 [110/1563] via 192.168.10.226, 00:00:09, Serial0/0/0 D 192.168.10.128/27 [90/21026560] via 192.168.10.226, 00:00:16, Serial0/0/0 49Refer to the exhibit. R1 and R2 are adjacent routers both running RIP. All interfaces on both routers are correctly cothe routing table. What is the likely cause? The adjacent interfaces are passive. The distance of 120 exceeds 15 hops. R2 will not accept version 1 updates from R1. Routes are being summarized by R1 but not by R2. 50It is saved in the topology table for use if the primary route fails. It may be backed up by a feasible successor route. It is used by EIGRP to forward traffic to the destination. It is flagged as active in the routing table. After the discovery process has occurred, the successor route is stored in the neighbor table. 51Refer to the exhibit. PC1 is unable to access the Internet. What is the cause of the problem? An incorrect IP address is configured between the two routers. No static route is configured on Router2. A routing loop has occurred. No routing protocol is configured on either of the two routers. 52Refer to the exhibit. A technician has configured the interfaces on the Router, but upon inspection discovers that inte FastEthernet0/1 is not functioning. Which action will most likely correct the problem with FastEthernet0/1? A clock rate should be added to the interface configuration. The subnet mask should be added to the interface configuration. An interface description needs to be added to the interface configuration. The no shutdown command needs to be added to the interface configuration. 。

思科ITE章考试原题及答案图文稿思科I T E章考试原题及答案集团文件版本号：（M928-T898-M248-WU2669-I2896-DQ586-M1988）清洁计算机内部可以减少以下哪种负面环境因素？灰尘在清洁计算机机箱内部时，直接喷射压缩空气容易损坏下列哪种组件？风扇在生产车间，一个家具工厂用笔记本电脑来实现进程监控和报告。

生产车间的环境温度大约为27 摄氏度（80 华氏度）。

湿度相当高，大约为70%。

风扇安装在通风口顶部。

这里的木屑灰尘非常多。

以下哪个条件最可能对在这一环境中使用的笔记本电脑产生不利影响？灰尘蔬菜罐头工厂使用笔记本电脑来监控生产线。

生产环境的环境温度大约是 24 摄氏度（75 华氏度）。

湿度约为 30%。

由于装罐设备的使用，因此噪音很高。

笔记本电脑放在一个木箱中，木箱三面距离笔记本电脑较近。

以下哪个因素最可能对在这一环境中使用的笔记本电脑产生不利影响？放置笔记本电脑的木箱科考队正在用笔记本电脑工作。

科学家们工作地点的温度范围为 -13 华氏度（-25 摄氏度）到 80 华氏度（27 摄氏度）。

湿度约为 40%。

噪声水平较低，但地形崎岖，风速可达每小时 45 英里（每小时 72 公里）。

在需要时，科学家们会停下脚步，用笔记本电脑输入数据。

下列哪一项条件最有可能对于在此环境下使用的笔记本电脑造成负面影响？温度以下哪一项是制定预防性维护计划的一部分？记录每项维护任务的详细信息和频率技术人员正在施工现场执行 PC 硬件维护。

作为预防性维护计划的一部分，技术人员应该执行什么任务？进气风扇除尘。

以下哪项任务应作为硬件维护例行程序的一部分？检查并固定任何松动的电缆。

在测试导致某个问题的若干可能原因时，应该首先测试哪类原因？最容易最明显的原因在解决计算机问题时可以使用下列哪两项物品来帮助制定行动计划（选择两项。

）计算机手册计算机维修历史记录日志为客户排除计算机故障之前应该备份哪两类数据（选择两项。

参加考试 - ERouting Final Exam - ${COURSENAME} (版本 ${VERSION}) 窗体顶端剩余时间:窗体底端1窗体顶端请参见图示。

哪台路由器会通告子网 172.16.1.32/28？Router1Router2Router3Router4窗体底端窗体顶端请参见图示。

所有路由器都运行相同的路由协议。

根据图示及其显示的命令，下列哪一项叙述正确？通配符掩码配置有误。

必须在每台路由器上配置默认路由。

路由器 B、C 和 D 无法访问 Internet。

路由协议进程未通告通往 ISP 的链路。

窗体底端3 窗体顶端请参见图示。

所有路由器都运行 RIPv1。

10.1.1.0/29 和 10.1.1.16/29 这两个网络无法互相访问。

此问题的原因可能是什么？因为 RIPv1 是无类协议，不支持该访问。

RIPv1 不支持不连续网络。

RIPv1 不支持负载均衡。

RIPv1 不支持自动总结。

窗体底端窗体顶端请参见图示。

路由器 R1 和 R2 通过其串行接口直接相连，并且都在运行 EIGRP 路由协议。

R1 和 R2 可以 ping 通其邻居的直连串行接口，但无法与邻居建立起EIGRP 相邻关系。

应采取什么措施来解决此问题？启用两台路由器的串行接口。

配置 EIGRP 以发送定期更新。

在路由器之间配置相同的 hello 发送间隔。

使用相同的 EIGRP 进程 ID 配置两台路由器。

窗体底端5窗体顶端请参见图示。

对于发往 192.168.2.0 的数据包，R2 会采取什么操作？它会丢弃数据包。

它会通过 S0/0/0 接口转发数据包。

它会通过 Fa0/0 接口转发数据包。

它会将数据包转发给 R1。

窗体底端窗体顶端请参见图示。

为实施 RIPv2 协议，网络管理员运行了所示命令。

但是， show ip protocol 命令未显示任何输出。

管理员应如何解决该命令没有输出的问题？添加 default-information originate 命令。