水密连接器Micro Circular系列技术说明

IP Rated Wire-to-Wire, Wire-to-BoardPages 2-32-34-54-56-789-109-1011-1213Series Type Current Rating Pitch 560Wire to Wire 3A 2.5mm 560Wire to Board 3A 2.5mm 566Wire to Wire 2A2.0mm 566Wire to Board 2A 2.0mm 567Wire to Wire 8A 5.9mm 24568Wire to Wire 12A n.a.Assembly InstructionsToolsSectional Area Gauge / AWG#Sectional Area Gauge / AWG#2.0mm²101214 5.2mm²260.13mm²220.33mm²360.01mm²16 1.31mm²300.05mm²200.52mm²340.02mm²0.08mm²28180.83mm²320.03mm²572Wire to Wire 10A 5.8mm 572Wire to Wire 10A 5.8mmAssembly instructions for 560 and 572 SeriesHand Crimp Tool, Ejection Tool and Auto-Crimp Machine0.21mm²3.3mm²QUICK REFERENCE GUIDE•Using the quick reference guide above, select the type of solution you need and proper current rating for your application and refer to the section of the product guide with the series you have selected.•Select the part with the appropriate number of contacts required for your application and the mating connector if required.(Quantities shown are standard pack quantities)•If applicable, using the Wire Seal Selection Guide in the series section, select the seal required for the wire gauge to be used in the application.•Contacts are supplied on the reel & bulk. See specific series section for more information on the available standard quantities.Custom assemblies are available in all series directly from EDAC, manufactured to yourspecifications. Contact EDAC or your local representative for more information.HOW TO USE THIS PRODUCT GUIDEWIRE GAUGE REFERENCE GUIDEEDAC's waterproof Wire to Wire and Wire to Board series were designed for both extreme moisture and non-submersion applications supporting both low-level signal and power applications up to 12A and 300V.Major applications include automotive, commercial and recreational vehicles, outdoor lighting, appliances, marine & aftermarket products, solar power installations, industrial equipment, process control, construction equipment, outdoor broadcast systems and portable devices.EDAC's waterproof series come in pitch sizes ranging from 2.0mm to 5.9mm and feature silicone rubber gaskets either pre-installed in all-in-one plugs and receptacle housings or loose and available in a range of sizes to accomodate wire from 28AWG to 14AWG with either thin or standard wire insulation. Operating temperature range across the whole series of -40°C to +105°C.Some of the unique features of EDAC's waterproof series include integral locking and double locking tabs designed to prevent accidental disengagements, keying system to prevent mismating, circuit sizes from 1 to 9 positions and visual confirmation of proper sealing.Application tooling available includes hand tools for prototype and small builds to fully automated presses and applicators for high production applications. EDAC also offers the whole series in custom cables already fully assembled.AWG#Ins. Dia.Pcs/Reel20-22Max. Ø1.78,00022-28Max. Ø1.68,000AWG#Ins. Dia.Pcs/Reel 20-22Max. Ø1.78,000Housing 22-28Max. Ø1.610,000Contact Housing Contact Wire O.D.Color565-290-711565-290-721Ø1.00 to Ø1.30PCB Thickness565-290-731565-290-741Yellow Ø1.30 to Ø1.70OrangeCrimp & Poke Applicable Contact Part No 565-290-741565-290-7211.6mm565-200-100PBT with Glass, UL 94V-015 mΩ max-40°C to +105°CPBT, UL 94V-0Part No.Insulation ResistanceTemperature Range1000 MΩ min./DC500VPhosphor BronzeContact PlatingTin PlatingBrassWire & Housing Seals Silicone Rubber PCBHeader Waterproofing CapPBT, UL 94V-0Male Contact (Pin)Female Contact (Socket)Pitch250V 2.5mm Withstanding Voltage Rated Voltage Part No 565-290-731565-290-711No. of Positions 2, 3, 5P Rated Current1000V AC (rms)3A maxContact Resistance SERIES 560Ordering Code:Waterproofing Cap:Wire to Wire / Wire to Board 2.5mm Pitch•2.5mm Pitch, Rated Current: 3A max•Fully Waterproof with Double Latch Solution•Available in Wire-to-Wire and Wire-to-Board Options •Seals Preassembled into Housing; No External Sealing Required available in 2, 3, or 5 Positions •True Crimp and Poke Solution•Waterproofing Cap available to cover holes of wire seal •Internal Polarization to Prevent Mismating •Available with wire already installed •Waterproof Grade IP67 CertifiedSpecifications:Crimp Contact:**Crimp Contacts are also available in strips of 60pcs.Contact EDAC for more information.Rear Gasket (Wire Seal):NO. OF CONTACTS:002 - 2 CONTACTS 003 - 3 CONTACTS 005 - 5 CONTACTSCONTACT CODE:000 - NO CONTACTS (ONLY FOR CRIMP CONTACTS)420 - BOARD MOUNT CONTACTSSTYLE:101 - WHITE MALE HOUSING (ONLY FOR BOARD MOUNT CONTACTS)301 - BLUE MALE HOUSING (ONLY FOR BOARD MOUNT CONTACTS)110 - WHITE MALE HOUSING FOR WIRE INSULATION Ø1.00 TO Ø1.30310 - BLUE MALE HOUSING FOR WIRE INSULATION Ø1.00 TO Ø1.30111 - WHITE MALE HOUSING FOR WIRE INSULATION Ø1.30 TO Ø1.70311 - BLUE MALE HOUSING FOR WIRE INSULATION Ø1.30 TO Ø1.70210 - WHITE FEMALE HOUSING FOR WIRE INSULATION Ø1.00 TO Ø1.30410 - BLUE FEMALE HOUSING FOR WIRE INSULATION Ø1.00 TO Ø1.30211 - WHITE FEMALE HOUSING FOR WIRE INSULATION Ø1.30 TO Ø1.70411 - BLUE FEMALE HOUSING FOR WIRE INSULATION Ø1.30 TO Ø1.70560-002-000-110SERIES:560, WIRE TO WIRE WIRE TO BOARD Assembly LayoutMaterials:**Wire seals, housing seals and retainers are already pre-assembled in the connector.560-002-000-XXX560-002-000-XXX560-002-420-XXX560-003-000-XXX 560-003-000-XXX 560-003-420-XXX560-005-000-XXX 560-005-000-XXX 560-005-420-XXXWhite 110White 210White101Blue 310Blue 410Blue301White 111White 211Blue311Blue411NOTE: Waterproofing Cap is installed at the wire seal end to cover the unused holes.Ø1.30 to Ø1.70Ø1.00 toØ1.30Ø1.30 toØ1.70Ø1.00 to Ø1.30XXXØ Wire Insulation Housing Color XXX Housing Color Housing Color Ø Wire Insulation XXX SERIES 560Wire to Wire / Wire to Board 2.5mm PitchMale Housing:Female Housing:PCB HeaderWaterproofing CapMale Housing:Female Housing:PCB Header:AWG#Ins. Dia.Pcs/Reel22-28Ø1.0~Ø1.512,000AWG#Ins. Dia.Pcs/Reel 22-28Ø1.0~Ø1.512,000Housing Contact Housing Contact Wire O.D.ColorPart No Ø1.25 to Ø1.50Orange566-200-100566-290-711566-290-721Female Contact (Socket)Part No 566-290-721Light Blue PCB Header PBT with Glass, UL 94V-0BrassContact PlatingTin PlatingWire & Housing Seals Silicone Rubber Waterproofing CapPBT, UL 94V-0Applicable Contact Ø1.00 to Ø1.25Crimp & Poke PBT, UL 94V-0Phosphor BronzeContact Resistance 10 mΩ maxInsulation Resistance 1000 MΩ min./DC500VTemperature Range -40°C to +105°C PCB Thickness1.6mmWithstanding Voltage 1000V AC (rms)No. of Positions 2, 3, 4, or 6P Male Contact (Pin)Pitch2.0mm Part No Rated Voltage 250V 566-290-711Rated Current2A maxSERIES:566, WIRE TO WIRE WIRE TO BOARD 566-002-000-710NO. OF CONTACTS:002 - 2 CONTACTS 003 - 3 CONTACTS 004 - 4 CONTACTS 006 - 6 CONTACTSCONTACT CODE:000 - NO CONTACTS (ONLY FOR CRIMP CONTACTS)421 - BOARD MOUNT CONTACTS (PCB) ONLY FOR 2 & 3 PIN SIZESTYLE:701 - BLACK MALE HOUSING (ONLY FOR BOARD MOUNT CONTACTS)710 - BLACK MALE HOUSING FOR WIRE INSULATION Ø1.00 TO Ø1.25711 - BLACK MALE HOUSING FOR WIRE INSULATION Ø1.25 TO Ø1.50810 - BLACK FEMALE HOUSING FOR WIRE INSULATION Ø1.00 TO Ø1.25811 - BLACK FEMALE HOUSING FOR WIRE INSULATION Ø1.25 TO Ø1.50SERIES 566Ordering Code:Waterproofing Cap:•2.0mm Pitch, Rated Current: 2A max•Fully Waterproof Solution available in 2, 3, 4, or 6 Positions (2 and 3 Positions Only for Wire to Board)•Available in Wire-to-Wire and Wire-to-Board Options •Seals preassembled into housing; no external sealing required•True Crimp and Poke Solution•Waterproofing cap available to cover holes of wire seal •Available with wire already installed •Waterproof Grade IP67 CertifiedSpecifications:Crimp Contact:**Crimp Contacts are also available in strips of 60pcs.Contact EDAC for more information.Rear Gasket (Wire Seal):Assembly LayoutWire to Wire / Wire to Board 2.0mm PitchWaterproofing CapMaterials:**Wire seals and housing seals are already pre-assembled in the connector.566-002-000-XXX566-002-000-XXX566-002-421-701566-003-000-XXX 566-003-000-XXX 566-003-421-701566-004-000-XXX 566-004-000-XXX566-006-000-XXX 566-006-000-XXXØ1.00 toØ1.25BlackØ1.25 to Ø1.50810Ø WireInsulation Housing Color XXX Ø Wire Insulation Housing Color Black711Ø1.25 to Ø1.50Black 811XXX Ø1.00 to Ø1.25Black 710SERIES 566Wire to Wire / Wire to Board 2.0mm PitchMale Housing:Female Housing:PCB HeaderMale Housing:Female Housing:AWG#Ins. Dia.Pcs/Reel14Max. Ø3.14,00020-16Max. Ø3.14,00020-16Max. Ø3.14,00022-20Max. Ø2.74,000AWG#Ins. Dia.Pcs/Reel 14Max. Ø3.14,00020-16Max. Ø3.14,00020-16Max. Ø3.14,00022-20Max. Ø2.74,00022-20Max. Ø2.74,000Wire O.D.ColorØ Dia.Height Ø1.7~Ø2.1Black Ø 5.0 6.0Ø2.1~Ø2.7Light Blue Ø 5.0 6.0Ø2.1~Ø2.7Blue Ø 5.0 6.7Ø2.7~Ø3.1BrownØ 4.95.0No. of Positions 1, 2, 3, 4, 6, or 9P Male Contact (Pin)Pitch5.0mm x 5.9mm Part No (Material)Rated Voltage 300V 570-290-751 (Brass)Rated Current8A max570-291-731 (Ph. Brz.)Part No (Material)Withstanding Voltage 1700V AC (rms)570-290-731 (Brass)Contact Resistance 10 mΩ max570-290-711 (Brass)Insulation Resistance1000 MΩ min./DC500VTemperature Range-40°C to +105°CFemale Contact (Socket)Part No.AWG#570-290-761 (Brass)570-291-741 (Ph. Brz.)Housing PBT, UL 94V-0570-290-741 (Brass)ContactPh. Brz. or Brass 570-291-721 (Ph. Brz.)Contact Plating Tin Plating570-290-721 (Brass)Wire SealSilicone Rubber570-260-00420-14570-260-00122570-260-00222-20570-260-00322-20SERIES 567Wire to Wire / Splash Proof 5.0x5.9mm Pitch•5.0mm x 5.9mm Pitch, Rated Current: 8A max •Splashproof Solution available in 1, 2, 3, 4, 6, or 9 positions•Available in Wire-to-Wire Options•True Crimp and Poke Solution with various sized wire seals available•Available with wire already installed•Splash Proof Grade IP52 (JIS C0920) CertifiedOrdering Guide:567-002-000-100NO. OF CONTACTS:001 - 1 CONTACT 002 - 2 CONTACTS 003 - 3 CONTACTS 004 - 4 CONTACTS 006 - 6 CONTACTS 009 - 9 CONTACTSCONTACT CODE:000 - NO CONTACTS (ONLY FOR CRIMP CONTACTS)STYLE:310 - WHITE MALE HOUSING FOR CRIMP CONTACTS SERIES:567, WIRE TO WIRE Assembly LayoutSpecifications:Crimp Contact:**Crimp Contacts are also available in strips of 40pcs.Contact EDAC for more information.Wire Seal:Materials:570-260-001570-260-002570-260-004570-260-003567-001-000-310567-002-000-310567-003-000-310567-004-000-310567-006-000-310567-009-000-310567-001-000-410567-002-000-410567-003-000-410567-004-000-410567-006-000-410567-009-000-410SERIES 567Male Housing:Female Housing:Wire to Wire/ Splash Proof 5.0x5.9mm PitchAWG#Ins. Dia.Pcs/Reel14Max. Ø3.14,00020-16Max. Ø3.14,00020-16Max. Ø3.14,00022-20Max. Ø2.74,000AWG#Ins. Dia.Pcs/Reel 14Max. Ø3.14,00020-16Max. Ø3.14,00020-16Max. Ø3.14,00022-20Max. Ø2.74,00022-20Max. Ø2.74,000Wire O.D.ColorØ Dia.Height Ø1.7~Ø2.1Black Ø 5.0 6.0Ø2.1~Ø2.7Light Blue Ø 5.0 6.0Ø2.1~Ø2.7Blue Ø 5.0 6.7Ø2.7~Ø3.1BrownØ 4.9 5.0568-001-000-100568-001-000-200Rated Voltage 300V Male Contact (Pin)Rated Current12A maxPart No (Material)Withstanding Voltage1700V AC (rms)570-290-751 (Brass)Contact Resistance 10 mΩ max570-291-731 (Ph. Brz.)Insulation Resistance 1000 MΩ min./DC500V570-290-731 (Brass)Temperature Range-40°C to +105°C570-290-711 (Brass)Female Contact (Socket)Housing PBT, UL 94V-0Part No (Material)ContactPh. Brz. or Brass 570-290-761 (Brass)Contact Plating Tin Plating570-291-741 (Ph. Brz.)Wire SealSilicone Rubber570-290-741 (Brass)570-291-721 (Ph. Brz.)570-290-721 (Brass)Part No.AWG#570-260-00122570-260-00222-20570-260-00322-20570-260-00420-14SERIES 568Ordering Guide:Assembly LayoutWire to Wire / Splash Proof•Rated Current: 12A max•Splashproof Solution for Single Position •Available in Wire-to-Wire Option•True Crimp and Poke Solution with various sized wire seals available•Available with wire already installed•Splash Proof Grade IP52 (JIS C0920) CertifiedMale Housing:Female Housing:Specifications:Crimp Contact:**Crimp Contacts are also available in strips of 40pcs. Contact EDAC for more information.Materials:Wire Seal:570-260-001570-260-002570-260-004570-260-003AWG#Ins. Dia.Pcs/Reel14Max. Ø3.14,00020-16Max. Ø3.14,00020-16Max. Ø3.14,00022-20Max. Ø2.74,000AWG#Ins. Dia.Pcs/Reel 14Max. Ø3.14,00020-16Max. Ø3.14,000Housing 20-16Max. Ø3.14,000Contact 22-20Max. Ø2.74,000Housing22-20Max. Ø2.74,000ContactWire O.D.ColorØ Dia.Height Ø1.7~Ø2.1Black Ø 5.0 6.0Ø2.1~Ø2.7Light BlueØ 5.06.0Ø2.1~Ø2.7Blue Ø 5.0 6.7Ø2.7~Ø3.1BrownØ 4.95.0No. of Positions 1, 2, 3P Male Contact (Pin)Pitch5.8mm Part No (Material)Rated Voltage 300V 570-290-751 (Brass)Rated Current10A max570-291-731 (Ph. Brz.)PCB Thickness1.6mmPart No (Material)Withstanding Voltage 1700V AC (rms)570-290-731 (Brass)Contact Resistance 10 mΩ max570-290-711 (Brass)Insulation Resistance 1000 MΩ min./DC500VTemperature Range -40°C to +105°C Female Contact (Socket)570-290-761 (Brass)570-291-741 (Ph. Brz.)Crimp & PokePBT, UL 94V-0570-290-741 (Brass)Ph. Brz. or Brass570-291-721 (Ph. Brz.)PCB HeaderPBT with Glass, UL 94V-0570-290-721 (Brass)BrassContact PlatingTin PlatingWire & Housing SealsSilicone RubberPart No.AWG#570-260-00122570-260-00222-20570-260-00322-20570-260-00420-14SERIES 572Ordering Guide:Wire to Wire / Wire to Board 5.8mm Pitch•5.8mm Pitch, Rated Current: 10A max•Fully Waterproof with Double Latch Solution•Available in Wire-to-Wire and Wire-to-Board Options •Seals preassembled into housing; no external sealing required available in 1, 2, or 3 Positions •True Crimp and Poke Solution•Internal Polarization to Prevent Mismating •Available with wire already installed •Wide range of wire sizes available •Waterproof Grade IP67 CertifiedSpecifications:Crimp Contact:**Crimp Contacts are also available in strips of 40pcs.Contact EDAC for more information.**Housing seals are already pre-assembled in the connector.Wire Seal:NO. OF CONTACTS:001 - 1 CONTACT 002 - 2 CONTACTS 003 - 3 CONTACTSCONTACT CODE:000 - NO CONTACTS (ONLY FOR CRIMP CONTACTS)420 - BOARD MOUNT CONTACTSSTYLE:101 - WHITE MALE HOUSING (ONLY FOR BOARD MOUNT CONTACTS)301 - BLUE MALE HOUSING (ONLY FOR BOARD MOUNT CONTACTS)100 - WHITE MALE HOUSING FOR CRIMP CONTACTS 300 - BLUE MALE HOUSING FOR CRIMP CONTACTS 200 - WHITE FEMALE HOUSING FOR CRIMP CONTACTS 400 - BLUE FEMALE HOUSING FOR CRIMP CONTACTS572-002-000-100SERIES:572, WIRE TO WIRE WIRE TO BOARD Assembly LayoutMaterials:570-260-001570-260-002570-260-004570-260-003572-001-000-XXX572-001-000-YYY572-001-420-XXX572-002-000-XXX 572-002-000-YYY 572-002-420-XXX572-003-000-XXX 572-003-000-YYY 572-003-420-XXXWhite 100White 200White101Blue300Blue400Blue301HousingColor XXXHousing ColorYYY HousingColorXXX SERIES 572Wire to Wire / Wire to Board 5.8mm PitchMale Housing:Female Housing:PCB HeaderMale Housing:Female Housing:PCB HeaderSTEP 1:•Prepare the cable wire of stripped length of 2.0mm•Crimp the contact to the cable wire as shown in Fig.1 for the female contact and in Fig.2 for the male contact560 SeriesFig.1: Showing female contact back sideFig.2: Showing male contactback side STEP 2:•Ensure that the back side of the contact is aligned to the open slot of the pre-assembled housing before inserting•Insert the contact + wire assembly into the housing until a "click" sound is heard.•Illustrations are shown on:Fig.3: Female HousingFig.4: Male HousingFig.3: Female Housing Pre-assembled with wire sealFig.4: Male HousingPre-assembled with wire sealOpen SlotOpen SlotRear InsulatorRearInsulatorSTEP 3:•After the wires are inserted, press the rear insulator to finish the connector assembly NOTE: The 2 ribs of the rear insulator should be within the window opening of the housing •Illustrations are shown on:Fig.5: Female Connector Assembly Fig.6: Male Connector AssemblyFig.5: Female Connector AssemblyFig.6: Male Connector Assembly2 Ribs2 RibsFig.7572 SeriesSTEP 1:•Prepare the cable wire of stripped length of 5.0mm •Ensure that the wire seal's shoulder is properly placed on the contact, as shown in Fig.7•This is applicable to both Female and Male contacts STEP 2:•Crimp the contacts to cable + wire seal as shown on:Fig.8: Male Contact Assembly Fig.9: Female Contact AssemblyWire Seal's ShoulderFig.8Fig.9STEP 3:•In a position as shown in:Fig.10: Male contact assembly's crimp side is aligned opposite the wider side of the male housingFig.11: Female contact assembly's crimp side is aligned opposite the lower latch of the female housing•Insert the contact + wire assembly into the housing until a "click" sound is heardFig.11Fig.10Crimp SideCrimp SideWider Side Lower LatchSTEP 4:•Press in the wire seal to finish the assembly, as shown in:Fig.12: Male Connector AssemblyFig.13: Female Connector AssemblyFig.12Fig.13AUTOMATIC CONTACT CRIMP MACHINE TOOLCONTACT HAND CRIMP TOOLTOOLSHand Crimp Tool, Ejection Tool, Auto-Crimp Tool•Part Number 516-280-700 for base machine•Applicators available to crimp all 560, 566, 567, 568 and 572 series contacts•All required guards for operator safety •Easy access for all setting changes •Foot switch to initiate crimp cycle •Mounts to any bench surface•Quick change applicators allow for fast conversions from one contact type to another•Requires 110V 50/60Hz electrical supply•Part Number: 565-280-210•Hand crimp tool for 560, 567, 568 and 572 series contacts •Manual hand crimp tool•Uses contacts on carrier strip, crimps them and cuts the contacts from the carrier•For 566 series, use crimper 566-280-200CONTACT EJECTION TOOL•Part Number: 565-280-301•Ejection tool for 560 series contacts•Part Number: 570-280-300•Ejection tool for 567, 568 and 572 series contacts。

MICROBRIDGE 汽车行业应用产品MICROBRIDGE - 汽车行业应用产品我司一如既往地致力于满足汽车行业客户的要求，继续推出MicroBridge系列产品。

此线对板连接器是根据 VW75174 和 USCAR-2 汽车测试规范开发而成。

MicroBridge 可以满足汽车行业的高标准要求，特别是在连接可靠性方面。

Koshiri 的安全性以及可选的电连接器定位装置 (CPA) 可确保实现安全和正确的连接。

尽管针距仅为 1.27 毫米，但 MicroBridge 非常坚固，其采用双边互锁锁扣，能承受剧烈的车辆振动。

而且，其紧凑型设计非常适合在有限的安装空间中使用。

此连接器的耐受温度高达 150°C，可暴露在严苛温度条件下，例如靠近车前灯 LED 的区域。

单列绝缘刺破式 (IDC) 母连接器提供 90° 和 180° 电缆出线，而专为表面贴 (SMT) 设计的公连接器有直通式和弯角式两种版本可供选择。

不同针数版本可采用不同的颜色和机械编码，使得连接器更容易区分并防止不正确的连接。

技术细节间距 1.27 毫米针数2-20 针 （单列） 可选板材尺寸0.5 毫米针尺寸0.5 x 0.4 毫米单端子额定电流20°C 时最高 9.0 A（2 针版本）端接技术公连接器 SMT母连接器 IDC （绝缘刺破式）电缆IDC 离散电缆 0.35 mm 2连接器单列 SMT 公连接器，垂直式或直角式单列 IDC 母连接器，带 90° 或 180° 电缆出线编码/颜色*黑色（蓝色，绿色，红色可选）汽车标准基于 VW75174 和 USCAR-2 汽车测试规范开发性能直角式或垂直式公连接器 - 带 90° 电缆出线的母连接器垂直式或直角式公连接器 - 带 180°电缆出线的母连接器垂直式或直角式公连接器 - 带 90°电缆出线的母连接器* 由于使用不同的塑料，公母连接器的颜色无法做到完全一致。

HR10-PC-211High performance miniature circular connectorsHR10 SeriesFeatures1. A simple, yet highly reliable design for compact, high density applicationsAlthough small i n si ze, the HR10 seri es are full featured connectors with a well integrated design.2.E xtremely ea sy ma ting/unma ting operationsEasy to operable, the single-action push-pull lock structure allows for quick and efficient locking and unlocking.1A p r .1.2019 C o p y r i g h t 2019 H I R O S E E L E C T R I C C O ., L T D . A l l R i g h t s R e s e r v e d .q Model name : Indicates the HR10A Series. The part type is identified as follows. HR10A : Lower cost type HR10G : Shield type HR10B : Coaxial contact typew Shell size : The shell size is the outer shell diameter or the mating interface end of the plug.e Shell type P : PlugR : Receptacle J : Jackr Number of contacts t Contact form P : Male contact S : Female contacty Contact termination method: None : Solder termination C : Crimp terminationu Other specifications : A two-digit character is added to indicate other specifications as needed.Product Number StructureRefer to the chart below when determining the product specifications from the product number.Please select from the product numbers listed in this catalog when placing orders.HR10A -7P -3P C (**)qw er t yu2HR10 Series ●High performance miniature circular connectorsA p r .1.2019 C o p y r i g h t 2019 H I R O S E E L E C T R I C C O ., L T D . A l l R i g h t s R e s e r v e d .Diagrams of Connectors in CombinationNotes1 : When using a plug with male terminal, be sure to use a receptacle or jack fi tted with female terminal.2 : Standard fi nish of the terminal is gold plating for the HR10, and silver plating for the HR10A and HR10G.Be sure to use male and female connectors of the same plating.(HR10 Type Plug)(HR10 Type Jack)(HR10B Type Receptacle)(HR10A-[ ]T Type Receptacle)(HR10A-[ ]T Type Jack)(HR10A Type Jack)(HR10 • HR10A HR10G Type Receptacle)(HR10A Type Plug)(HR10B Type Plug)(HR10A-[ ]T Type Plug)3HR10 Series ●High performance miniature circular connectorsA p r .1.2019 C o p y r i g h t 2019 H I R O S E E L E C T R I C C O ., L T D . A l l R i g h t s R e s e r v e d .HR10 typeHR10 type connectors, use a gold plated contact as the standard plating specification. Silver plating is used on the contacts for other series such as HR10A and HR10G. To avoid mixing gold and silver contacts, please be sure to confirm the plating specification when using HR10 type connectors with HR10A or HR10G connectors.PlugØDA MaxØCØB(Representative example)HR10-7P-6S(73)ReceptacleE(HEX)DA5.76.3ØCØBRemarks : For mounting holes, see page 20.(Representative example)HR10-7R-6S(73)4HR10 Series ●High performance miniature circular connectorsA p r .1.2019 C o p y r i g h t 2019 H I R O S E E L E C T R I C C O ., L T D . A l l R i g h t s R e s e r v e d .Receptacle (PCB dip type)D(HEX)CDip post dia.Ø0.55G F5.7EØAØBRemarks : 1. For mounting holes, see page 20. 2. For dip post arrangement, see page 16.(Representative example)HR10-7R-6SA(73)JackØD5.5A MaxØBØC(Representative example)HR10-7J-6S(73)5HR10 Series ●High performance miniature circular connectorsA p r .1.2019 C o p y r i g h t 2019 H I R O S E E L E C T R I C C O ., L T D . A l l R i g h t s R e s e r v e d .Plug (Solder type)ØB ØCØDA(Representative example)HR10A-7P-6P(73)Plug(Crimp type)ØCØBØDA(Representative example)HR10A-7P-6PC(73)HR10A •10G TypesHR10A connectors are a lower-cost version, yet still provide a high "Value Add" while preserving the superior characteristics of the HR10 connectors. Cable clamps are crimped using a special crimping tool, and the shells have a rubber boot which provides a flexible design that helps to prevent cable twisting.The HR10G connector is a shielded type connector which has an internal contacting structure between the plug shell and receptacle shell.Contacts in both HR10A and 10G connectors are silver plated as standard.6HR10 Series ●High performance miniature circular connectorsA p r .1.2019 C o p y r i g h t 2019 H I R O S E E L E C T R I C C O ., L T D . A l l R i g h t s R e s e r v e d .Receptacle (Solder type)E(HEX)DØBØCA 5.7F(Representative example)HR10A-7R-6S(73)Receptacle (Crimp type)C D(HEX)EFØBØA(Representative example)HR10A-10R-12SC(71)7HR10 Series ●High performance miniature circular connectorsA p r .1.2019 C o p y r i g h t 2019 H I R O S E E L E C T R I C C O ., L T D . A l l R i g h t s R e s e r v e d .Dust capBØA10.2ØDØC ØE2HR10-7R-CReceptacle (Dip type)D(HEX)CDip post dia.0.2∞0.5ØAØBG F5.7ERemarks : 1. For mounting holes, see page 20. 2. For dip post arrangement, see page 16.(Representative example)(Representative example)HR10A-7R-6SB(73)8HR10 Series ●High performance miniature circular connectorsA p r .1.2019 C o p y r i g h t 2019 H I R O S E E L E C T R I C C O ., L T D . A l l R i g h t s R e s e r v e d .Jack (Solder type)ØCØB5.5AØD(Representative example)HR10A-7J-6S(73)Jack (Crimp type)ØCØBDAØE(Representative example)HR10A-7J-6SC(73)9HR10 Series ●High performance miniature circular connectorsA p r .1.2019 C o p y r i g h t 2019 H I R O S E E L E C T R I C C O ., L T D . A l l R i g h t s R e s e r v e d .PlugHR10B Type ConnectorThe HR10B connector combines 10 signal lines and one coaxial contact in the standard number 10 shell. Performancespecifications for the coaxial contacts are on the 11 page.Ø14.7AØB(Representative example)HR10B-10P-10PC(73)Receptacle13(HEX)M11∞0.75Ø11.9Ø146.312Remarks : For mounting holes, see page 20.(Representative example)HR10B-10R-10SC(71)A p r .1.2019 C o p y r i g h t 2019 H I R O S E E L E C T R I C C O ., L T D . A l l R i g h t s R e s e r v e d .Plug(clamp)4.15.23.6Ø3.87.118.05Ø4.2Ø1.1(Representative example)HR10B-2.5CP(73)Jack(clamp)Ø2.657.2518.2Ø4.2Ø1.14.15.2 3.6(Representative example)HR10B-2.5CJ(73)Coaxial contactsThe coaxial contacts shown here are for use with the HR10B connector.These contacts have locking barbs and are inserted from the rear of connector.Please use the following information to select the correct terminals.Materials / FinishPerformanceA p r .1.2019 C o p y r i g h t 2019 H I R O S E E L E C T R I C C O ., L T D . A l l R i g h t s R e s e r v e d .Cable connecting methods11±0.51.4±0.23.7±0.2(2.5)Slit cable outer jaket 2 pieces (180° reverse side)1. Dimensions for cable end treatment are shown in Fig 1.2. Termination is described below.(1) Strip cable outer jacket as indicated.(2) Slit outer jacket on both sides per Fig.1.(3) Fold back outer cover.(4) Remove insulator from cable.1. Cable end treatmentFig.1Male pinSolderingShould fix flushContact fixing jig such as vise1.S older male pin to cable center conductor as indicated in Fig.2.(1) Pre-solder the solder pot of pin with Ø0.5mm string solder.(2) Male pin should fit flush against the cable insulator as shown.(3) Remove any excess solder from the pin with a knife.This surface must be smooth.(4) A properly soldered terminal will yield 500gf when stretched.2. Soldering male pin to cable center conductor15±0.21.I nsert the cable into the connector and make sure to push it all the way in. To confirm that the cable is fully inserted, make sure that the depth is 1.5 ± 0.2mm by measuring from the end of the connector to the tip of the male contact by using a vernier calipers or other suitable measuring device.2.U se the HR10-TC-01 tool to crimp the metal fitting to the cable.3. Crimping cable outer conductorFig.3HR10B-2.5CP(73)HR10B-2.5CJ(73)A p r .1.2019 C o p y r i g h t 2019 H I R O S E E L E C T R I C C O ., L T D . A l l R i g h t s R e s e r v e d .HR10A-( )T Type (Threaded Coupling Type)HR10A-( )T connector is a new product having a threaded coupling locking mechanism. Electric parformance is same as HR10 and HR10A push-pull locking type connectors.Plug (Crimp type)43Ø7Ø17Ø9.5M 13∞0.75HR10A-10TP-12PC(73)(Representative example)(Representative example)Plug (Solder type)ØCB ØA DØEHR10A-10TP-12P(73)*Waterproof plug need resin fi lling inside when connector assembly.When mated, the connector against water penetration.A p r .1.2019 C o p y r i g h t 2019 H I R O S E E L E C T R I C C O ., L T D . A l l R i g h t s R e s e r v e d .Remarks : 1.For mounting holes, see page 15. However, 7TR size shell be referred to page 20 on the shell size 7.2.For dip post arrangement, see page 16.Receptacle (Solder type)AF(HEX)CØDB5.7E Remarks : For mounting hole, see page 15(10TR,10WTR) 20(7TR).HR10A-10TR-12S(73)(Representative example)Receptacle (Crimp type)DEF(HEX)ØABCRemarks : For mounting hole, see page 15HR10A-10TR-12SC(73)(Representative example)Receptacle (Dip type)C D(HEX)BDip post HØAE5.7FG HR10A-10TR-12PB(73)(Representative example)A p r .1.2019 C o p y r i g h t 2019 H I R O S E E L E C T R I C C O ., L T D . A l l R i g h t s R e s e r v e d .Jack (Solder type)*Waterproof jack need resin fi lling inside when connector assembly.When mated, the connector against water penetration.DØABØC(Representative example)HR10A-10TJ-12S(73)Panel mounting hole dimensions (Screw coupling)The mounting hole dimensions shown below are for connectors to be tightened by a hexagonal nut from the back of the panel. The dimensions below apply only to the HR10A-( )T and not the 7TR. For the dimensions of connectors of other types, see page 20.9.6+0.10Ø11.1+0.10Ø10.6+0.10Ø14.1+0.10Type HR10A-10TR (Panel thickness 1 to 2mm)Type HR10A-10TR (Panel thickness 1 to 2mm)9.6+0.10Type HR10A-10WTR(Panel thickness 1 to 2mm)8.6+0.11.6+0.10Type HR10A-13TR(Panel thickness 1 to 1.5mm)A p r .1.2019 C o p y r i g h t 2019 H I R O S E E L E C T R I C C O ., L T D . A l l R i g h t s R e s e r v e d .Male contactFemale contactAA1.151.2110AA1011.151.2Receptacle dip post arrangement dimensionsContactRemarks : 1. Use cables with a coating outside diameter of 1mm or less. 2.L oose piece terminal are available in packs. Each pack contains 100 terminals. Strip terminals are available in reels. Each reel contains 10,000 terminals.Remarks : 1. Use cables with a coating outside diameter of 1mm or less. 2.L oose piece terminal are available in packs. Each pack contains 100 terminals. Strip terminals are available in reels. Each reel contains 10,000 terminals.Remarks : 1. T he above fi gures are views from the mating side and pin inserts from the wiring-connection side. 2. D imensional tolerance of ±0.05 is recommended for the board arrangement.1.131.131.561.561.137-size 4 cores7-size 6 cores10-size 10 cores10-size 12 cores13-size 20 cores1.130.90.91.81.8(4 Places)(6 Places)(10 Places)(12 Places)(20 Places)23411.8 1.81.81.87-size 5 cores(5 Places)235411623452.52.58 2.382.380.950.952.752.110.550.482.852.850.950.951.11.382.52.55 2.55111 1.77 1.770.82.440.82.442.71 2.711112910876543221567891016151413121117181920343456712111098Ø0.8 0.10Ø0.8 0.10Ø0.8 0.1Ø0.8 0.10Ø0.8 0.10Ø0.8 0.10A p r .1.2019 C o p y r i g h t 2019 H I R O S E E L E C T R I C C O ., L T D . A l l R i g h t s R e s e r v e d .Tools(HT802/HR12-SC-1)Hand Crimp Tool(HR10A-TC-02)Hand Cable Crimp Tool(HR10B-TP)Coaxial Contact Removal Tool(HR12-SC-TP)Auto Crimp Tool CM-105C(RP6-SC-TP)Extraction ToolApr.1.219Copyright219HIROSEELECTRICCO.,LTD.AllRightsReserved .How to use a connectorHR10-10P-T02HR10-10J-T04PanelPlug CableReceptacle APanelPlugCableReceptacleAPanelBPlug connection sleeve CablePanelPlug connection sleeveBCableConnecting toolsWhen terminating the wires, use the jigs noted below for easy assembly / disassembly of the connector parts.A p r .1.2019 C o p y r i g h t 2019 H I R O S E E L E C T R I C C O ., L T D . A l l R i g h t s R e s e r v e d .Cable assembly procedure on plug sideThis applies also to the jack side assembly procedure.No special procedure is given here for the receptacle side because no special procedure is necessary.For any question on using the plugs, contact our sales or engineering department.P shell unitPlug bodyBifurcated partClamp washerTightenerCableFace BFace A Spanner jaw distanceAbout 2CA p r .1.2019 C o p y r i g h t 2019 H I R O S E E L E C T R I C C O ., L T D . A l l R i g h t s R e s e r v e d .Recommended Mounting HoleMounting hole dimension shown here is tight by hexagon nut from back side.Contact ArrangementABØCNotes 1. The contact arrangement shown here is the mating surface of socket insert assembled.2. The withstanding voltage shown here is test voltage value.3. The isulation resistance value is measured at DC100V.4. The contact resistance value is measured at DC1A.20HR10 Series ●High performance miniature circular connectorsA p r .1.2019 C o p y r i g h t 2019 H I R O S E E L E C T R I C C O ., L T D . A l l R i g h t s R e s e r v e d .2-6-3,Nakagawa Chuoh,Tsuzuki-Ku,Yokohama-Shi 224-8540,JAPAN TEL: +81-45-620-3526 Fax: +81-45-591-3726The characteristics and the specifications contained herein are for reference purpose. Please refer to the latest customer drawings prior to use.The contents of this catalog are current as of date of 12/2017. Contents are subject to change without notice for the purpose of improvements.Precautions1. S witch off the power of the circuit before disconnecting or plugging-in the connector.2. U se a connector with socket contacts at the power side of the circuit.3. M ake sure that the coupling is in completely locked position.4. C able clamping, cable rotation, and other forces may vary with the cable construction. Please make sure that your cable is suitable for use with these connectors before usage and production.5. T his product series uses silver plated contacts. Silver reacts easily to exposure to sulfur gas so the below conditions may cause tarnishing. Dusty environmentsA rea with a high concentration area of gases such as sulfur dioxide gas, hydrogen sulfide gas, nitrogen dioxide gas and so on.Example; In close proximity to factory exhaust, automotive emissions, etc. Close to heaters, or in other areas marked by extreme temperature differences or high humidity. Close to rubber products includes rubber adhesives.The Electrical connection is not affected by tarnishing on a silver surface due to the wiping effect of the contact pins.StoragePacking state; Packed in original packing or equivalent container Temperature -10 to +60çHumidity 85% Max(It is recommended that the product be stored in an area of normal level of temperature and humidity, and free of any temperature fluctuation)Please use this products within 6 months of delivery.(After 6 month, please check the solderbility before use)“Storage” means long-term storage of the unused products in sealed packaging, prior to assembly to PCB.21HR10 Series ●High performance miniature circular connectorsA p r .1.2019 C o p y r i g h t 2019 H I R O S E E L E C T R I C C O ., L T D . A l l R i g h t s R e s e r v e d .HR10-PC-211。

M Series 水深3000公尺乾式連接器 (2)8810 Series 水深3000公尺濕式連接器 (34)TP Series 水深300公尺使用 (46)MIL-Grade 軍規防水氣密連接器 (72)851 / M26482Ⅰ Series (80)8525 Series (86)8526 / M26482Ⅱ Series (95)8533 / M83723 Series (102)8D / M38999 Series (110)8STA / M38999 microminiature (119)D-Sub / M24308 Serious (122)Special Design Range Extension (125)MSH / MPH Series 推薦海軍使用防水連接器 (130)其他IP68 / IP69等級防水防塵連接器 (166)UTO Series 具EMI效果 (166)UTS Series 抗UV效果，塑化材質 (168)衛星及太空站使用 (170)RF Solutions 高頻類連接器 (174)M Series 8810 Series8810 Series - Underwater mateable 水深3000公尺濕式結合........................................458121315171821223334434344444545Submarines Towed Streamers VesselsOil and GasROVs & AUVsMarine Renewable Energies©Curraheeshutter/Shutterstock©Iurii/Shutterstock©Donvictori/Fotolia©U.S.Army©AlexandrMitiuc/Fotolia©IngvarTjostheim/ShutterstockOverviewO v e r v i e wO v e r v i e w► F ib e r o pti c s a n d H y b rid► P re s s u reB a la n c e d O il F il le d(P B O F )► B ig g e r siz e 28M► D o u b leW a te rt ig h tn e s s► L a rg e r ba c k s h e ll s iz e (GM )► H ig h c urr e n t/H ig h v o lt a gePCE (SA or SB)PCETERTECRDECSC*RECSCPCDE*PCE (PBOF)*Pressure Balanced Oil FilledO v e r v i e w1. Receptacle2. Plug3. Insert with sealed contact4. Insert/Shell O 'Ring seal5. Plug/Receptacle taper seat with O'Ring seal6. Panel/Receptacle O'Ring7. Removable protective boot8. Cable outer sheath/Plug watertightness by packing seal3. Insert with sealed contact4. Insert/Shell O 'Ring seal6. Poting housing7. Outer sheath cable/Plug watertightness by customer over molding 1633456745278Mechanical• Shell:Nickel aluminium bronze• Insulator: PTFE (T) PCTFE (K)Other materials are available upon request (Peek, Silicone, PBTFV)Electrical• Voltage rating (Vrms)• Current rating and contact resistance:Description• Marine connectors • Screw coupling• Sealing between plug and receptacles performed by 2 O-rings• Standard watertightness: Sealing on cable achieved by packing washers• Plugs for over molding (SA/SB): Sealing on cable is given by overmoldingVoltage CategorySOURIAU recommended service voltage (Vrms 50 Hz)Dielectric Withstanding Voltage (Vrms50Hz)Technical featuresS t a n d a r d R a n g eS t a n d a r d R a n g eØFØAØFS t a n d a r d R a n g e3#20 Service 27#20Service 19#20Service 04#16Service 25#16Service 12#14Service 23#14Service 2Triax#50ΩService 11Coax# 50Ω or 75Service 14#167#201CX75*Number of contacts #SizeVoltage Service Rating3#12Service 24#12Service 27#14Service 21#06Service 21Triax50Ω#751Coax#50Service 21TX75*19#20Service 112#16Service 241#20Service 127#16Service 132#16Service 121#14Service 17#12Service 216#12Service 24#06Service 23#06Service 21#02Service 24Coax#50Ω or 75ΩService 14C77*StandardRange61#16Service 148#16Service 16#16Service 437#14Service 227#12Service 24#02Service 23#06Service 23#02Service 2M Series Standard Range0.1 K0.2M a x . t o 45°H Max.A B On fl ats JNØMØK 0+0.1ØEØFØGS t a n d a r d R a n g e9M 10M 22376.3140.2M a x . t o 45°A CØFØECDDDDBP0.1 KØQHoles ØL4 blind threaded holesPanel cut-out ØK 0+0.1S t a n d a r d R a n g eDCOn fl ats SOn fl ats J ØB MaxØA DCOn fl ats J On fl ats S ØB MaxØA DDCCOn fl ats J On fl ats J On fl ats S ØB MaxØB MaxØA ØA ØEØE9M 10M 14M 20M 24M100127220DDDDCCG ABPOn fl ats S0.1 K4 holes ØL4 b l i n d t h r e a d e d h o l e sM MaxØQØFØJ Max ØJ1 Max 0.2M a x . t o 45°ØES t a n d a r d R a n g eØK 0+0.1Panel cut-outC CEE GGOn fl ats JOn fl ats JOn fl ats J1On fl ats J1On fl ats SOn fl ats S DDØFØF ØA ØB ØB ØA1ØA1ØAShell size: 9M - 10M - 14M - 20MShell size: 24MFED PCES t a n d a r d R a n g eØMH Max.0.2M a x . t o 45°0.1 KØGØEØEp l u g U s e P i nOn fl ats JA B NØK 0+0.114M 20M 24M A 0.2M a x . t o 45°H Max.D4 b l i n d t h r e a d e d h o l e s 0.1 KCØQ4 holes ØLCDDBPØEØEPanel cut-out ØK 0+0.19M 10M 20M 24M R = Mated shells overlapROn fl ats SC240ØDOn fl ats JA 240ØBNote: All dimensions are in millimeters (mm)S t a n d a r d R a n g eShell size9M 10M 14M R11191912322REC-RER Receptacles FED Plug 24325TEC-TER BulkheadBER CapRECSC Square flange in-line receptacleS t a n d a r d R a n g eThis tool is used for holding the cable clamp while tightening the sleeveP/N : 410.01Plug SizeTool P/N MA1W6010B58810 Series於水深3000公尺下濕式接合使用8810 Series36378810 Seriescurrent rating per contact: 7.5A max4 # 200.93 mm27 # 20 0.93 mm24 # 161.34 mm21 Ø 18400 A185 mm24 Ø 10150 A percontact 70 mm22 # 845 A45 mm212 # 161.34 mm237 # 161.34 mm268 # 161.34 mm212 # 20 0.93 mm2 19 # 20 0.93 mm238 # 20 0.93 mm28810 SeriesE across flatsGD F1 2ØAØBØCE across flatsE across flatsGØAKØDØCØBGHKØAØDØCØBJ F12HF12shell size 7shell sizes 1–4shell size 5–638394041shell size 7shell size 5–6E G1FFGE across flatsØDHKE1FH across flatsØCGØAØBD across flatsØAØCØBL LLC4 holes ØMH across flatsØCD across flatsØAØBshell size 7shell size 5–6G12F ØC BEØAD across flatsHØDFacross flatsØAØCØBKE KØEHLF across flatsMGØAØDØCØB12124243shell size 5–6FGE across flats ØDFGH FGH KØDØAØCØBLLL4 holes ØME across flatsKØDLØAØCØBLLE across flats 4 holes ØMØAØC ØBLLLH K4 holes ØMshell size 7Ordering informationAAAØCØDØCBB8810 SeriesOrdering informationAAABBØCØCØCR a n g e E x t e n s i o n. Up to 15 000VRMS (Dielectric Withstanding Voltage at 50 Hz)4849e SContentsThe TP Series connectors meet the highest standards of safety for aquatic environment. it is currently used in many applications: vessels, civil construction, diving, heavy industry…The TP Series feature a large range of shell styles and layouts. Derived from the widely recognized marine bronze M Series, the TP Series are the perfect trade off between high performances and cost efficiency.PresentationO t h e r S e r i e sP r o d u c t D e t a i l s O v e r v i e w6GeophysicsVesselsDiving©S.Dubrov/Fotolia©M.Simonia/Fotolia©donvictori/Fotolia©Corlaffra/Fotolia©O.Sved/Fotolia©qq471828/FotoliaFeatures & BenefitsFIELD PROVEN ROBUST PERFOR-MANCESEASY COUPLING Used in Aquatic EnvironmentOil and gas services: Geophysics, inspection or instrumentationWater treatment: Pumps, valves, sewage systemCivil construction: Tunnels, dams, buildingsUnderwater instrumentation: Buoys, sensors, cameras, lightsKeying and Easy Couplingeasy coupling/uncoupling operation even with high density layout5-key mechanical polarizationScoop proof to prevent contact damageHigh Performance LevelsWaterproof down to 300 meters depthNo stress on O-rings by conical couplingWithstanding 500 mating/unmating cyclesDesigned for Harsh EnvironmentTemporary immersion in sea waterProlonged immersion in freshwater and use in presence of mud, sand…High resistance to cable pull out or transverse forcesrepairable connectors with removable insertsOverview50515253O v e r v i e wEasy wiring and installationScoop proof: No risk of damaging contacts during the coupling operation when using a female plug and a male receptacle. Removable insulators: To allow easy wiring and replacement in case of wiring mistakes or servicing.Easy mating: Easy coupling operation thanks to the screw coupling and locking even with a high number of contact Equipment protection: No coupling mistake thanks to the polarization key.O v e r v i e wPressure Sealing Capfor ReceptaclePlugs5657Mechanical • Shell:Nickel plated brass• Insulator:PA6/6+MOS2 - Nylatron ® (N)PTFe – Teflon ® (T) (on request for reduced water absorption and increased pressure withstand when unmated)Electrical • Voltage rating (Vrms)• Current rating and contact resistance:Description• Sealed connectors • Screw coupling• Sealing between plug and receptacles performed by 2 O-rings• Sealing on cable thanks to packing washerVoltage CategorySOURIAU recommended service voltage (Vrms 50 Hz)Dielectric Withstanding Voltage (Vrms50Hz)Technical features• Operating temperature range: - 20°C to + 70°C • Watertightness• Salt spray- 10 x (24h + 24h) alternate salt spray according to eN60068-2-11- 500h continuous salt spray according to NFC93422• Fluids Resistance- Oil, alcohol, petrol, diesel fuel, sea water - Various gases (natural, butane, propane, Freon)- Various acids (acetic, boric, citric)Mated Unmated 30 bar5 barP r o d u c t D e t a i l sAØsliateDtcudorPFØFØ58593#20Service 27#20 Service 14#16Service 2for part numbering5#16Service 12#14Service 23#14Service 21TX#75 or 1TX#50Service 11C#75 or1C#50Service 17#20Service 11C50*TX50*P r o d u c t D e t a i l s3#12Service 24#12Service 27#14Service 21#06Service 21TX#75 or 1TX#50Service 21C#50Service 2TX50*19#20Service 112#16Service 241#20Service 127#16Service 132#16Service 121#14Service 17#12Service 216#12Service 24#06Service 23#06Service 21#02Service 24C#50 or 4C75ΩService 14C50*6263P r o d u c t D e t a i l s0.1 K0.2M a x . t o 45°H Max.A BOn flats JNØMØK 0+0.1ØeØFØG64650.2M a x . t o 45°A CØFØeC DDDDBP0.1 KØQHoles ØL4 blind threaded holesØK 0+0.1P r o d u c t D e t a i l sØMH Max.0.2M a x . t o 45°0.1 KØGØeØep l u gU s e P i nOn flats JA B NØK 0+0.16667A 0.2M a x . t o 45°H Max.D4 b l i n d t h r e a d e d h o l e s 0.1 KC ØQ4 holes ØLC DDBPØeØeØK 0+0.1P r o d u c t D e t a i l s14TP 20TP DDDDC CGABPOn flats S0.1 K4 holes ØL4 b l i n d t h r e a d e d h o l e sH MaxØQØFØJ Max ØJ1 Max 0.2M a x . t o 45°ØeØK 0+0.1Panel cut-out6869DCOn flats J ØB MaxØA ØeP r o d u c t D e t a i l sDC On flats SOn flats J ØB MaxØA70718TP 20TP R = Mated shells overlapOn flats SC240ØDOn flats JA 240ØBNote: All dimensions are in millimeters (mm)Shell size8TP 10TP 14TP R111919P r o d u c t D e t a i l sR727312322REC-RER Receptacles FED Plug 24325TEC-TER Bulkhead BER CapRECSC Square flange in-line receptacleP r o d u c t D e t a i l sEnd wrenches7475Hermetic ConnectorsHigh Performance Sealing Solutions軍規防水氣密連接器M26482Ⅰ / VG95328EN2997 / ESC10 / M83723EN3646M26482ⅡM38999M38999 microminiature M24308Mil-Grade Hermetic74757678798086951021101191221251261261271271281281291297677Typical applicationsValves - Flowmeters High-Tech CamerasVacuum PumpsSensors© S O U R I A UActuators - Monitoring © Y u r y M a r y u n i n / F o t o l i a© T r o f o t o d e s i g n / F o t o l i a© V o l o d y m y r K y r y l y u k / F o t o l i aN a t i o n a l M u s e u m o f t h e U S A i r F o r c eFeatures & Benefi tsHIGHSEALINGSPACE SAVINGLARGE OFFERCUSTOMSOLUTIONROHSHermetic connectorLeak rate less than 10-7cm 3/s at 1 bar pressure difference under helium.Less than 1 cm 3 leaks in 4 months.Adapted to specifi c needWide range of custom solutions based on standard defi nition: specifi c shell, materials, contact length, grounding, ...Environment friendlyNo lead content.Wide range of standardsLarge connectors offer available in circular as well as rectangular ranges: EN2997, MIL-C-26482 Series I & II, EN3646, MIL-C-38999, micro38999, D-Sub, ...CompacityNo need of additional rear accessories.1/3 shorter than watertight connector equivalent.Solder mount option for full equipment integration.7879Standard glass to metalStandard hermeticGlass to metal sealing+A d d e df u n c t i o n sSolder contacts on both sidesCompact designSee page 64Rack & panelBlind matingSee page 63FeedthroughEasy MRO (Maintenance, Repair and Operations )See page 63Removable crimp contactsIdeal for fuel immersionSee page 62127128126127 sealing technologies+A d d e d f u n c t i o n sContact grounded on the shellIntegrated grounded functionSee page 65Titanium30% weight savingPCB contacts / Stand-offsRobust PCB mount designSee page 62ThermocouplesAccurate temperature data communicationSee page 65129129126851 Series 8525 Series 8526 Series8533 Series 8D Series8STA Series D-Sub Series119 122Standard glass to metal sealing technologiesAlternative sealing technologies Capability to ProvideCustom Solutions► Tight tolerances,► Specifi c shells,► Specifi c contacts,► Filtering, ...Ex: Custom EN2997Technical Support► Souriau engineering team willproactively support your newdesigns. Contact us!► Free 3D models available online:N E WFull plastic hermeticBig volume low weight hermeticResin sealedFlexible low weight hermeticSee page 668081Materials Electrical82838485Ordering informationBasic series85102H1832P50Shell type:IH: Solder mount receptacle 02H: Square fl ange receptacle 07H: Jam nut receptacleShell size:08, 10, 12, 14, 16, 18, 20, 22, 24 Contact layout:See previous page Contact type: P: PinOrientation:None: Normal (N)W, X, Y, Z - see page 19Mandatory suffi x:50: Gold plating for contact size 20 and size 16Specifi cation:None: Yellow cadmium plating - 02H and 07H only Nickel plated - IH only44: Nickel plated - 02H and 07H onlyVG95328 qualifi ed productsBasic seriesVG95328F1832PNShell type:G: Solder mount receptacle P: Square fl ange receptacle F: Jam nut receptacleShell size:08, 10, 12, 14, 16, 18, 20, 22, 24 Contact layout:See previous page Contact type: P: PinOrientation:N, W, X, Y, Z - see page 19SOURIAU part numbers85858687ØADØGB CFØEA maxB ±0.2C ±0.2D ±0.14E 12.0313.8410.700.8014.2715.0113.8410.700.8017.07ØADBCF ØK ØEG JHA maxB ±0.2C ±0.2D ±0.14E ±0.02F max 13.8411.24 1.5514.277.5-0.13A maxB maxC ±0.25D maxE maxF ±0.112.0320.6017.9327.3724.0713.3315.0120.6017.9330.5727.2216.51Viewed from receptacle front face.Insulator rotated inside metal body.AngleØAØG B CF EDE8889MechanicalElectricalTechnical featuresAngleViewed from receptacle front face.Insulator rotated inside metal body.90919293ØAØDØFBCEØGPanel cut-outØAØDØHB CEFGFG ØJNKMØLKPanel cut-outShell A B ±0.55C D +0E FGH ±0.15J ±0.15K L +0M N9495ØAØDØHBCEF GFGSealing gasketØHJKØLKPanel cut-outA maxB maxCD maxE maxF maxGH J K #20#12/#1612.0213.14 6.8-14.27 2.626.418.1 3.8 3.518.1ØAØDBCEØGFHPanel cut-outShellsize A max B max C ±0.-5D max E ±0.25FG +0.25H +0.25min max 812.0218.34 2.427.3723.82 1.57 4.7514.413.48-0-09697Type 02H: Square fl ange receptacle Type 07H: Jam nut receptacleType IH: Solder mount receptacle W X YØZW X YØZWX YØZMechanicalElectricalTechnical featuresAngleViewed from receptacle front face.Insulator rotated inside metal body.9899。

2016 NO.03SCIENCE & TECHNOLOGY INFORMATION科技报告导读169 科技资讯 SCIENCE & TECHNOLOGY INFORMATION Abstract ：This program is established on the in the basis of our work during "11th five-year plan".In order to realize the mass production of high-performance hollow glass microspheres, our work will mainly focus on the engineering research. This achievement will promote the technology of solid buoyancy material. Our work going smoothly in 2013, the main content is as follows:(1)We deepened the research on the hollow glass microspheres of the density(0.38±0.02)g/cm 3.The comparison test indicates that the compression strength of T38 is better than S38, which from the 3M Company has the same density as T38.And the compression strength of T38 is even better than the S38hs, which has the volume collapse of 44.09% at the pressure of 5500 psi, while the volume collapse at 5500psi of T38 is only 33.75%.(2)We also researched on the surface modification of hollow glass microspheres, and provided the reference for the combination of hollow glass microspheres/resin system.(3)We prepared solid buoyancy material by homemade hollow glass microspheres and tested the mechanical behavior.Then we adjusted the formula and preparation process according to the testing results.(4)We also accomplished the sea tests of the solid buoyancy material. The winch test indicates that the pressure-resistance property of solid buoyancy material prepared by homemade hollow glass microspheres satisfy the contract requests. And the comparison test indicates that the pressure-resistance property of solid buoyancy material prepared by homemade hollow glass microspheres can be as well as the solid buoyancy material prepared by imported hollow glass microspheres. The subsurface buoy test indicates that solid buoyancy material prepared by homemade hollow glass microspheres can satisfy long-term deep sea circumstance.Key words ：Hollow glass microspheres，solid buoyancy material阅读全文链接（需实名注册）：/xiangxiBG.aspx?id=64058&flag=1M 系列深海水密电缆接插件开发科技报告薛萍 张博 葛雄浩 许晓冬(中国电科23所)摘 要：该文分引言、主体和结论三部分，详细介绍了深海通用系列水密电连接器的研究背景和意义、前期研究基础、研究范围和目标、研究思路和总体研究方案。

Fig.31Miniature Waterproof Plastic ConnectorsHR30 SeriesFeatures1. Small-size with low profile3, 6 contacts :M aximum outer diameter Ø12.6mm Mated length 32.3mm (from the panel surface)10, 12 contacts : M aximum outer diameter Ø15.5mmMated length 42.1mm (from the panel surface)These small, compact connectors offer unique features available only from Hirose.2. Waterproof constructionIPX7 and IPX8 waterproof construction in the mated state IPX7 : Left submerged in water at a depth of 1m for 30 minutes IPX8 : Left submerged in water at a depth of 2m for 14 days3. Push/pull lockWaterproof connectors feature an easy to operate push/pull locks developed with our exclusive technology.4. Light weight3 and 6 contacts : 6g (plug + receptacle)10 and 12 contacts : 9g (plug + receptacle)5. C lamp structureOur proprietary clamping method allows clamping the cable by simply tightening the cord ring.6. Easy mating operationThe plug can be securely locked while holding it in your hand while mating. (Fig.2)7. Mis-insertion preventionMating portions are polarized to avoid improper mating and connector damage.8. Mating markBoth the plug and the r eceptacle featur e a white index mar k on them which is used to quickly align the two interfaces for proper mating.(Fig.3)9. Complies with the RoHS requirementsIn consider ation of envir onmental issues, we use only materials that comply with the RoHS Directive.Push-pull- single action lockØ15.542.1Ø12.632.33 and 6 pos.10 and 12 pos.Mated dimensionsLock/release operationAlignment marksPolarized interfacePush-pull locking collarFig.1Fig.2HR30 Series●Miniature Waterproof Plastic Connectors10. High speed transmissionSupports Cat. 5e(1Gbps) high speed EthernetBased on ISO TR 11801-9902 Class D3 - Conn E3(End-to-End)Characteristics depend on pin assignment, cable specifications and cable assembly conditions. Please check prior to use.Please contact a Hirose representative for questions on the recommended pin assignment.11. Suited for long-term outdoor useSunshine weather meter test performed for 2,000 hours.For details, please contact us for the test reports.Product SpecifiMaterial / Finish23HR30 Series ●Miniature Waterproof Plastic ConnectorsProduct Number StructureRefer to the chart below when determining the product specifications from the product number.Please select from the product numbers listed in this catalog when placing orders.HR30 - 6 P A - 6 S C (* *)qw e r t y u iq Model name : HR30t Number of Contacts : 3, 6, 10 and 12y Contact type S : Female contact P : Male contact u Contact wiring typeBlank : SolderC : CrimpingD : Through hole i Other specifications:A two-digit character is added to indicate other specifications as needed.w Shell size: Outside diameter/plug mating side e Connector type : P : PlugR : Receptacle J : Jackr VariationBlank : Standard A : Fine wireB, D : Over mold type4HR30 Series ●Miniature Waterproof Plastic ConnectorsPlugsCrimp TypeSolder TypeØ15.5A(Fully tightened)Applicablecable diameterBA(Fully tightened)Applicablecable diameterHR30-7P-12SC (71)(Representative example)(Representative example)Shown with contacts installed.HR30-6P-6S (31)5HR30 Series ●Miniature Waterproof Plastic ConnectorsPlug for overmoldsCrimp TypeSolder Type25.9Ø15.5Ø6.4AØBØCHR30-8PB-12PCHR30-6PB-6S6HR30 Series ●Miniature Waterproof Plastic ConnectorsReceptaclesSolder TypeGasketBCADE(Thread)F(Hex nut)123456HR30-6R-6P (71)Through hole TypeHR30-8R-12SD (31)DC A B2Through hole post (0.2∞0.5)E F(Hex nut)GasketCrimp TypeØ11.5Ø1515.59.3GasketM11X1(Thread)13(Hex nut)HR30-7R-12PC (31)Shown with contacts installed.(Representative example)(Representative example)(Representative example)7HR30 Series ●Miniature Waterproof Plastic ConnectorsJacksCrimp TypeSolder Type37.3Ø15(Fully tightened)Applicablecable diameterB(Fully tightened)AApplicablecable diameterHR30-7J-12PC (71)HR30-6J-6P (31)Shown with contacts installed.(Representative example)(Representative example)8HR30 Series ●Miniature Waterproof Plastic ConnectorsJack for overmoldsCrimp TypeSolder TypeØ1523.7Ø6.4ABCHR30-6JB-6PHR30-8JB-12SC9HR30 Series ●Miniature Waterproof Plastic ConnectorsNote :W hen using these caps, do not use the gasket that is normally supplied with the receptacle. The “B” diameter end of the receptacle cap will serve as the gasket.CapsFor ReceptacleFor Plugs 1.40.9ØECØAØBØD11.4CØAØBØDØEHR30-6R-C (31)HR30-6P-C (31)(Representative example)(Representative example)10HR30 Series ●Miniature Waterproof Plastic ConnectorsNote : Use wire size 26 to 30 AWG with a jacket diameter of 1 mm max.Crimp ContactsDiagrams of Connectors in Combination0.82111.151.2A-A cross-sectionAA0.8211AAPlugsHR30-*P-**(71)Caps for Plug HR30-*P-C (71)Receptacles HR30-*R-**(71)JacksHR30-*J-**(71)Caps for Receptacle HR30-*R-C (71)Cap mounting diagramCableCapCapPanelMale contactFemale contactNote 1 :P lease use connectors with compatible shell size and number of contacts. If you are using a male contact plug, please also use a corresponding product with a female receptacle and a jack.Note 2 :P lease install the applicable crimping contacts when using the crimping style connectors. (Please refer to the manual for wiring work.)Note 3 :W hen using the cap on the receptacle side, do not use the gasket that is normally supplied with the receptacle. The Hirose cap has the necessary gasket as part of the cap unit.(Representative example)(Representative example)Solder termination fixtureBack shell tightening collar HR30-6P-6S-T01HR30-6R-6P-T01HR30-6P-T02Cable Assembly ToolsNote : W iring for soldering or disassembly and assembly of plugs and jacks can be accomplished more effi ciently when using the cable assembly tool.Tightening collar for back shellNote : T he code ring tightening collar is used to tighten the cord ring to the specifi ed torque.(Please refer to the manual for assembly procedures.)1112Contact Position ArrangementPanel CutoutRemarks : 1. The contact arrangement depicts a view from the wiring side. 2. I nstallation is accomplished by securing the receptacle from the back side of the panel using the supplied hexagonnut. The tightening torque of the hexagon nut should be 0.5 N·m for 3, 6 contacts, and 0.8 N·m for 10, 12 contacts.In addition, apply Loctite 263 and Lockprimer 7649 which are manufactured by Henkel Japan Ltd., Tokyo in order to prevent looseness.12312345661234512456789101211312456789101211312345678910HR30-7P-10SC (**)HR30-7P-12SC (**)HR30-8P-12PC (**)HR30-6P-6P (**)HR30-6P-6S (**)HR30-6P-3S (**)Alignment markAlignment markB+0.05A +0.05 0D +0.05ØC+0.05Receptacle, Board Mounting Through Hole PatternRemark : 1. T he receptacle through hole confi guration depicts a view from the mating side of the connector. 2.The above Δ mark indicates the guide key position. 3.The recommended board maximum thickness :1.2mm. 4. T olerance of +0.03mm is recommended for the plated through hole location. Tolerance of +0.02mm is recommendedfor the plated through hole diameter.7R-12PD8R-12SD6R-6SD 1542630.90.91.521.520.491.351.66-Ø0.656R-6PD 1.561.560.90.91.81.86-Ø0.651234560.90.9Assembly Procedures131415Points to note when using Heat shrink tubingPrecautions after wiring (Solder type and Crimp type)We recommend that you use shrink tubing over the solder connections in order to protect the soldered wires and to enhance insulation. However, please be careful when applying heat in this area when installing the shrink tube so excess heat does not bleed into or affect the resin parts as shown in the figure below.If the product does become heated beyond the area shown and into the resin parts, please make sure to prevent the following.q D eformation of the C ring. This could result in prevention of locking during mating.wM elting of some parts.To prevent the deformation of the C rings of the receptacles and the jack, we recommend heat to be applied after mating with a compatible plug.Before heating, please mate the plug in the receptacle securely, then pull the back shell for checking whether it is locked properly. If it is heated with semi-fitting, C ring may be thermally deformed with shrinking condition and it may not be locked properly.After wiring, do not seal the connected portion with potting, etc.Potting may cause the O-ring to come off when the applicable plug is removed.If the connector is used with the O-ring removed, the waterproof performance will not be satisfied.C ringShrinkable tubeHeat application area ReceptacleCompatible plugBack shell Heat application areaMated dimensionsReceptacleO-ringCompatible plugPotting non-compatibleLead wireEquipment housingReceptacle2-6-3,Nakagawa Chuoh,Tsuzuki-Ku,Yokohama-Shi 224-8540,JAPANhttps:///16The characteristics and the specifications contained herein are for reference purpose. Please refer to the latest customer drawings prior to use.The contents of this catalog are current as of date of 10/2022. Contents are subject to change without notice for the purpose of improvements.General usage notesPrecautions1. M ake sure the power is off before mating or un-mating the connector.2.W hen mating the connector, push it on with a force of a least 30N. After mating, pull slightly on the connector to check for proper mating and to ensure the connector is fi rmly locked to the receptacle.3.A fter mating the connector, do not apply a force over 30N to the cable in the directions shown by the arrows. An excessive load can lead to connector damage.4.T o maintain the waterproof performance, cable clamping force and cable stability, please use a cable within the recommended for cable diameters.Because the performance will differ depending on the cable structure, make sure to check all specifi cations of the cable assembly before use or production.5. P lease assemble and install the connector and components with the specifi ed tightening torque. If the tightening torque is too weak or too strong, loosening or breakage can occur.6. Please contact Hirose if your application requires compliance with the Electrical Appliance and Meterial Safety Act.7. Please note that the white label on the connector may come off due to solvents such as alcohol.Panel30N max.30N max.30N max.。

Design features for watertight locking devices•Thermoplastic elastomeric exterior out-performs rubber when exposed to moisture, chemicals, oils, and the effects of UV exposure and ozone attack•Mated plug and connector or plug and receptacle form a watertight seal that meets NEMA and IEC IP ratings (see specification sheet for details) and withstands water spray test at 1000 psi•High visibility safety yellow for identification. Also available in black•Power contacts, blades and terminal screws nickel-plated for corrosion resistance•Quick-drive stainless steel assembly screws for corrosion resistance and fast installation•Multiple color coded neoprene grommets for a watertight seal on a wide range of cord sizes• Receptacles have self-closing spring loaded flip lid covers • Santoprene™ grommets ensure watertight seal at cord entrance •Wide range cord diameter 0.30" – 0.65"2-pole, 3-wire grounding15A, 125/250V/AC; 20A, 125/250V/AC NEMA 5-15, 6-15, 5-20, 6-20Arrow Hart watertight locking plugs, connectors & receptacles60W33Project Name:Prepared By:Project Number:Date:Catalog Number:Type:T able 1. S traight blade plugs, connectors & receptacles2-pole, 3-wire60W48DPLX14W4715W47Catalog no.ReceptacleCordRatingPlug ConnectorSingle DuplexdiameterA V/AC NEMA14W47 15W47 60W47 60W47DPLX 0.30-0.65”(7.6-16.5mm)151255-15 14W49 15W49 60W49 60W49DPLX 0.30-0.65”(7.6-16.5mm)152506-15 14W33 15W33 60W33 60W33DPLX 0.30-0.65”(7.6-16.5mm)201255-20 14W4815W4860W4860W48DPLX 0.30-0.65”(7.6-16.5mm)202506-20Compliances, specifications and availability are subject to change without notice.2EATON /arrowhart Technical DataEffective March 2016Arrow Hart watertight locking plugs, connectors & receptaclesCompliances, specifications and availability are subject to change without notice.Catalog no.ReceptacleCordRatingPlug ConnectorSingle DuplexdiameterA V/AC NEMA24W47 25W47 65W47 65W47DPLX 0.30-0.65”(7.6-16.5mm)15125L5-15 24W49 25W49 65W49 65W49DPLX 0.30-0.65”(7.6-16.5mm)15250L6-15 24W3425W34 65W34 65W34DPLX 0.30-0.65”(7.6-16.5mm)15277L7-15 L520PW L520CW L520RW —0.36-0.84” (9.1-21.3mm)20125L5-20 L620PW L620CW L620RW —0.36-0.84” (9.1-21.3mm)20250L6-20 L720PW L720CW L720RW*—0.36-0.84” (9.1-21.3mm)20277L7-20 L820PW L820CW L820RW*—0.36-0.84” (9.1-21.3mm)20480L8-20 L530PW L530CW L530RW —0.43-1.15” (10.9-29.2mm)30125L5-30 L630PWL630CW L630RW —0.43-1.15” (10.9-29.2mm)30250L6-30 L730PW L730CW L730RW —0.43-1.15” (10.9-29.2mm)30277L7-30 L830PWL830CWL830RW—0.43-1.15” (10.9-29.2mm)30480L8-30*Not NOM certifiedProject Name:Prepared By:Project Number:Date:Catalog Number:Type:T able 2. Locking devices – 2-pole, 3-wireL530RW65W47DPLX24W4725W47L1020PWCatalog no.CordRating Plug ConnectorSingle receptaclediameterA V/ACNEMA9965PW 7314CW 7314RW 0.36-0.84” (9.1-21.3mm)20125/250Non-NEMA L1020PW L1020CW 0.36-0.84” (9.1-21.3mm)20125/250L10-20 L1120PW L1120CW L1120RW 0.36-0.84” (9.1-21.3mm)203Ø 250L11-20L1030PW L1030CW 0.43-1.15” (10.9-29.2mm)30125/250L10-30 3331PW 3333CW 0.43-1.15” (10.9-29.2mm)30125/250Non-NEMA L1130PWL1130CWL1130RW0.43-1.15” (10.9-29.2mm)303Ø 250L11-302-pole, 3-wire grounding15A, 125/250/277V/AC; 20A,125/250/277/480V/AC; 30A, 125/250/277/480V/AC NEMA L5-15, L6-15, L7-15, L5-20, L6-20, L7-20, L8-20, L5-30, L6-30, L7-30, L8-303-pole, 3-wire non-grounding 3-pole, 4-wire grounding20A; 125/250, 3Ø 250, 3Ø 480V/AC30A; 125/250, 3Ø 250, 3Ø 480, 3Ø 600V/ACNon-NEMA L10-20, L11-20, L10-30, L11-30T able 3. Locking devices – 3-pole, 3-wire3EATON /arrowhart Technical DataEffective March 2016Arrow Hart watertight locking plugs, connectors & receptaclesCompliances, specifications and availability are subject to change without notice.L1620RWProject Name:Prepared By:Project Number:Date:Catalog Number:Type:L1420CWCatalog no.CordRating PlugConnectorSingle receptacle diameterA V/ACNEMAL1420PWL1420CW L1420RW 0.36-0.84” (9.1-21.3mm)20125/250L14-20 L1520PW L1520CW L1520RW 0.36-0.84” (9.1-21.3mm)203Ø 250L15-20 L1620PW L1620CW 0.36-0.84” (9.1-21.3mm)203Ø 480L16-20L1430PW L1430CW 0.43-1.15” (10.9-29.2mm)30125/250L14-30 L1530PWL1530CW 0.43-1.15” (10.9-29.2mm)303Ø 250L15-30 L1630PW L1630CW 0.43-1.15” (10.9-29.2mm)303Ø 480L16-30 L1730PWL1730CW0.43-1.15” (10.9-29.2mm)303Ø 600L17-30T able 4.Locking devices – 3-pole, 4-wireCatalog no.CordRating PlugConnectorSingle receptacle diameterA V/ACNEMA7411PW 7413CW 7413RW 0.36-0.84” (9.1-21.3mm)203ØY 120/208Non- NEMA L1820PW L1820CW L1820RW 0.36-0.84” (9.1-21.3mm)203ØY 120/208L18-20 L1920PW L1920CW L1920RW 0.36-0.84” (9.1-21.3mm)203ØY 277/480L19-20 L2020PWL2020CW L2020RW 0.36-0.84” (9.1-21.3mm)203ØY 347/600L20-20 3433PW 3433CW 3433RW 0.43-1.15” (10.9-29.2mm)303ØY 120/208Non- NEMA L1830PW L1830CW L1830RW 0.43-1.15” (10.9-29.2mm)303ØY 120/208L18-30 L1930PW L1930CW L1930RW 0.43-1.15” (10.9-29.2mm)303ØY 277/480L19-30 L2030PWL2030CWL2030RW0.43-1.15” (10.9-29.2mm)303ØY 347/600L20-30T able 5. Locking devices – 4-pole, 4-wireReceptaclePlugNon-NEMA 20A 125/250V YWXReceptacle PlugNon-NEMA30A 125/250V3-pole, 3-wire non-grounding3-pole, 4-wire grounding20A; 125/250, 3Ø 250, 3Ø 480V/AC30A; 125/250, 3Ø 250, 3Ø 480, 3Ø 600V/ACNEMA L -14-20, L15-20, L16-20, L14-30, L15-30, L16-30, L17-304-pole, 4-wire non-grounding20A; 3ØY 120/208, 3ØY 277/480, 3ØY 347/600V/AC 30A; 3ØY 120/208, 3ØY 277/480, 3ØY 347/600V/ACNon-NEMA L18-20, L19-20, L20-20, L18-30, L19-30, L20-30L2030RWL1820PWL1820CWTechnical Data Effective March 2016Arrow Hart watertight lockingplugs, connectors & receptacles Compliances, specifications and availability are subject to change without notice.Catalog no.Cord RatingPlug Connector Single receptacle diameter A V/AC NEMA 7411PW 7413CW 7413RW0.36-0.84”(9.1-21.3mm)203ØY120/208Non-NEMA L1820PW L1820CW L1820RW0.36-0.84”(9.1-21.3mm)203ØY120/208L18-20L1920PW L1920CW L1920RW0.36-0.84”(9.1-21.3mm)203ØY277/480L19-20L2020PW L2020CW L2020RW0.36-0.84”(9.1-21.3mm)203ØY347/600L20-203433PW 3433CW 3433RW0.43-1.15”(10.9-29.2mm)303ØY120/208Non-NEMA L1830PW L1830CW L1830RW0.43-1.15”(10.9-29.2mm)303ØY120/208L18-30L1930PW L1930CW L1930RW0.43-1.15”(10.9-29.2mm)303ØY277/480L19-30 L2030PW L2030CWL2030RW0.43-1.15”(10.9-29.2mm)303ØY347/600L20-30T able 6. Locking devices – 4-pole, 4-wireL1830PWL1820CWCatalog no.Cord RatingPlug Connector Single receptacle diameter A V/AC NEMAL2120PW L2120CW L2120RW0.36-0.84”(9.1-21.3mm)203ØY120/208L21-20L2220PW L2220CW L2220RW0.36-0.84”(9.1-21.3mm)203ØY277/480L22-20L2320PW L2320CW L2320RW0.36-0.84”(9.1-21.3mm)203ØY347/600L23-20L2130PW L2130CW L2130RW0.43-1.15”(10.9-29.2mm)303ØY120/208L21-30L2230PW L2230CW L2230RW0.43-1.15”(10.9-29.2mm)303ØY277/480L22-30L2330PW L2330CW L2330RW0.43-1.15”(10.9-29.2mm)303ØY347/600L23-30T able 7.Locking devices – 4-pole, 5-wireReceptacle PlugNon-NEMA20A 125/250VYWXReceptacle PlugNon-NEMA30A 125/250VProject Name:Prepared By:Project Number:Date:Catalog Number:Type:4-pole, 4-wire non-grounding20A; 3ØY 120/208, 3ØY 277/480, 3ØY 347/600V/AC30A; 3ØY 120/208, 3ØY 277/480, 3ØY 347/600V/ACNon-NEMA L18-20, L19-20, L20-20, L18-30, L19-30, L20-304-pole, 5-wire grounding20A; 3ØY 120/208, 3ØY 277/480, 3ØY 347/600V/AC30A; 3ØY 120/208, 3ØY 277/480, 3ØY 347/600V/ACNEMA L21-20, L22-20, L23-20, L21-30, L22-30, L23-30 L2330RWL2120PWL2120CW4EATON /arrowhart5EATON /arrowhart Technical DataEffective March 2016Arrow Hart watertight locking plugs, connectors & receptaclesCompliances, specifications and availability are subject to change without notice.Device type Watertight plugs & connectors, straight blade & locking Watertight receptacles, straight blade & 15A locking Watertight receptacles, 20A & 30A locking Wiring typeBack wireBack wireBack wireTesting & code compliance • L isted to UL 498, file no. E3663• cUL Certified to C22.2, no. 182.2• Listed to UL 498, file no. E2369• cUL Certified to CAN/CSA C22.2 no. 42-99• Listed to UL 498, file no. E2369• NOM certifiedEnvironmental specificationsFlammability: Meets UL 94 requirements; V2 ratedFlammability: Meets UL 94 requirements; V2 ratedFlammability: Meets UL 94 requirements; V2 ratedTemperature rating: -40ºC to 75ºC (-40°F to 167°F)Temperature rating: -40ºC to 75ºC (-40°F to 167°F)Temperature rating: -40ºC to 75ºC (-40°F to 167°F)Protection: NEMA 4, 4X, 6, 6P & IP67Protection: NEMA 3, 3R, 4, 4X, 12 & IP66Protection: NEMA 3, 3R, 4, 4X, 12 & IP66High pressure water test: 1000 psi spray (mated or closed)High pressure water test: 1000 psi spray (mated or closed)High pressure water test: 1000 psi spray (mated or closed)Electrical specificationsDielectric voltage: Withstands 1500V per UL 498Dielectric voltage: Withstands 1554V per UL 498Dielectric voltage: Withstands 1696 - 2200V per UL 498Current interrupting: Yes, at full-rated currentCurrent interrupting: Yes, at full-rated currentCurrent interrupting: Yes, at full-rated currentTemperature rise: Max. 30ºC (86°F) after 250 cycles of overloadTemperature rise: Max. 30ºC (86°F) after 250 cycles of overloadTemperature rise: Max. 30ºC (86°F) after 250 cycles of overloadMechanical specificationsTerminal accommodation: #18 - 10 AWG Terminal accommodation: #18 - #10 AWG Terminal accommodation: #14 - #8 AWG Voltage ratings: Permanently marked on deviceVoltage ratings: Permanently marked on deviceVoltage ratings: Permanently marked on deviceIndustrial specification grade watertight devices are ideal for applications in food and beverage, agriculture, chemical processors, shipyards, marinas and wastewater treatment environments. Watertight receptacles feature spring-loaded flip-lid covers that provide watertight protection even under 1,000 psi water spray. Plugs, connectors and receptacles comply with various NEMA and IEC ratings as listed below.ApplicationsProject Name:Prepared By:Project Number:Date:Catalog Number:Type:T able 8. Specifications Receptacle flip lid cover & base N/A Thermoplastic, glass-filled nylon Thermoplastic, glass-filled nylon Receptacle cover spring N/A Stainless steel, self-closingStainless steel, self-closingReceptacle lid liner &mounting gasketN/ASantoprene™ thermoplastic elastomeric Santoprene™ thermoplastic elastomeric Plug/connector outer shell Santoprene™ thermoplastic elastomeric over glass filled polypropylene N/AN/AInterior body NylonGlass-filled nylon Glass-filled nylon Terminal retainer Clear polycarbonate Clear polycarbonate Clear polycarbonate Blades .060” thick brass, nickel plated N/AN/ALine contacts .032” thick copper alloy, nickel plated .032” thick copper alloy, nickel plated .032” thick copper alloy, nickel plated Ground shunt N/ASolid brass Solid brass Terminal clamps Steel, nickel platedSteel, nickel platedSteel, nickel platedTerminal screws #10-32 brass, neutral screw nickel plated #8-32 brass, neutral screw nickel plated #10-32 brass, neutral screw nickel plated Ground contact N/A.032” thick brass, nickel plated .032” thick brass, nickel plated Ground screw#10-32 brass, zinc plated (green)#8-32 brass (green)#10-32 brass (green)Assembly/mounting screws Stainless steel Stainless steel Stainless steel Compression nut Nylon N/A N/A Compression nut grommet Santoprene™N/A N/A Receptacle mounting plateN/AStainless steelStainless steelT able 9. MaterialsTechnical DataEffective March 2016Arrow Hart watertight locking plugs, connectors & receptaclesCatalog no.60W4960W49DPLX ••••60W3360W33DPLX ••••60W4860W48DPLX •••14W4715W47••••14W4915W49••••14W3315W33••••14W4815W48••••65W4765W47DPLX 24W4725W47••••65W4965W49DPLX 24W4925W49••••65W3465W34DPLX24W3425W34••••L520RW L520PW L520CW ••••L620RW L620PW L620CW ••••L720RW L720PW L720CW •••L820RW L820PW L820CW •••L530RW L530PW L530CW ••••L630RW L630PW L630CW ••••L730RW L730PW L730CW ••••L830RW L830PW L830CW ••••7314RW 9965PW 7314CW ••••L1020RW L1020PW L1020CW ••••L1120RW L1120PW L1120CW ••••L1030RWL1030PW L1030CW ••••3333RW3333PW3333CW••••Certifications & compliancesKEY:cULus ROHS426NOMParts are manufactured and designed in accordance with article 4 of the European Union’s RoHS2 directive 2011/65/EUProject Name:Prepared By:Project Number:Date:Catalog Number:Type:Catalog no.L1420RW L1420PW L1420CW ••••L1520RW L1520PW L1520CW ••••L1620RW L1620PW L1620CW ••••L1430RW L1430PW L1430CW ••••L1530RW L1530PW L1530CW ••••L1630RW L1630PW L1630CW ••••L1730RW L1730PWL1730CW ••••7413RW 7411PW 7413CW •••L1820RW L1820PW L1820CW ••••L1920RW L1920PW L1920CW ••••L2020RW L2020PW L2020CW ••••3433RW 3431PW 3433CW •••L1830RW L1830PW L1830CW ••••L1930RWL1930PW L1930CW ••••L2030RW L2030PW L2030CW ••••L2120RW L2120PW L2120CW ••••L2220RW L2220PW L2220CW ••••L2320RW L2320PW L2320CW ••••L2130RW L2130PW L2130CW ••••L2230RW L2230PW L2230CW ••••L2330RWL2330PWL2330CW••••For ordering devices, include Cat. no. followed by the color code: (Black), Y (Yellow)T able 10. Color ordering informationEaton is a registered trademark.All other trademarks are property of their respective owners.Eaton1000 Eaton Boulevard Cleveland, OH 44122United States Electrical Sector203 Cooper CirclePeachtree City, GA 30269United States /arrowhartElectrical Sector Canada Operations 5925 McLaughlin RoadMississauga, Ontario, L5R 1B8CanadaEatonCanada.ca/arrowhartElectrical Sector Mexico Operations Carr. Tlalnepantla -Cuautitlán Km 17.8 s/n Col. Villa Jardín esq.Cerrada 8 de MayoCuautitlán, México CP 54800México Eaton.mx/arrowhart© 2016 EatonAll Rights Reserved Printed in USAPublication No. SB630002EN March 2016。

体用螺钉连接起来，两者之间采用O 型密封圈进行密封，O 型密封圈是经典的密封方式，密封可靠性强，插头前端壳体与后端壳体对接处密封的可靠性得以保障。

1—外护套；2—绕包层；3—填充物；4—绝缘；5—铜芯导体。

图1 电缆结构示意图电连接器后端电缆线密封采用硫化密封是较为常见的密封方式。

本文研究的电连接器电缆端密封方式为非硫化密封。

由于电连接器长期工作在水下恶劣的环境中，为了保证电连接器的水密性，如图2所示，电连接器采用二级密封。

第一级密封第二级密封图2 二级密封位置示意图如图3所示，第一级密封为电缆后端壳体1与密封环载体3之间均为金属采用O 型密封圈4密封。

因密封环载体3与电缆2之间为金属和刚度较弱的非金属，所以在水深1 500 m 的工况下此处采用O 型密封圈是不可能密封住的。

因此密封环载体与电缆之间的密封是否可靠是电连接器水密封的关键技术，0 引言近几十年由于经济全球化，全球经济得到高速发展，在这个发展过程中石油、天然气的消耗也是巨大的，这就促使石油、天然气开采由陆地走向海洋，由浅海走向深海。

水下电连接器(以下简称电连接器)是水下采油气装备中关键部件，目前国内市场上的电连接器基本被国外SEACON 、SOURIAU 、GISMA 、BEDIX 等公司产品所垄断[1-3]。

电连接器广泛使用在石油天然气、军事等领域[4]，而且其密封技术是保密的。

电连接器国产化是必然趋势。

电连接器在国内近十年来早有公司及科研单位进行研究，性能稳定可靠的产品极少。

电连接器应用在非常恶劣的深水环境，水密性是急需解决的关键技术，其中胡晓东等[5]针对O 型密封圈应用在电连接器上的静态密封进行了研究，但胡晓东等未针对电连接器插合工况下的密封进行研究。

赵宏林等针对电连接器插合工况下进行了研究[6]，得出在理想环境电连接器插合过程中密封是可靠的。

以上研究未针对电连接器电缆端密封进行研究。

电缆端常规的密封方法为硫化，但这种密封对硫化要求较高，一旦硫化过程出现瑕疵，就导致密封或电绝缘失效，而且采用硫化密封电连接器维修不方便，一旦出现短路或水密性问题查找根源较为困难。