powermill后处理修改方法（PowerMILL post-processingmodification method）Machine fanucom -- -- post-processing file headerDefine word TN ---------------------------- defined fields;Address letter = "TOOL TYPE:-" - defines the return value of the fieldAddress width = 13 defines character widthField width = 25 defines the width of the word returned End define end definitionThe define format (/ G6, S, T, M2, L, P, D, E, H, O) M1 is defined in the form of theAddress width = 1------------ defines character width Address width = 1------------ defines character widthField width = 2 - definition of return word widthExponent width = 0 - width indexScale factor = 1 - scale factor: value multiplied by 1 Scale divisor = 1 - scale factor: value divided by 1Leave a space before the word "tape position = 1-----------"Print position = 1 - print positionSign = none----- is used without the need for G code and feed rateSign = if negative only identifies negative coordinatesSign = always, if needed + / -Not permanent - does not require line numberNot modal - only when changes need to repeat the word for modal. (modal).Typically, the G code is X, Y, and Z are coordinates of modal,But the I, J, and K codes that are usually used by the center are usually not, so they are not modalMetric formats - MetricLeading zeros = false - leading 0Trailing zeros = true - Guide 0Decimal point = false --- does not need a decimal pointDecimal places = 2 - 2 decimal pointsImperial formats - InchWord order===================== word orderWord order = (OP, N, G1, G2, G5, G3, G4, etc)Word order = (+, G6, G7, X, Y, Z, B, C)Word order = (+, I, J, K, R, D, S, T)Word order = (+, H, M1, M2, MS, MSG, EM, Q)Word order = (+ Q1, Z2, R2, ID, F)Word order = (+, TN, TD, TR, DY, MT, YR, PM)The third paragraph of define keys is the definition keyBlocknumber = N - defined programPreparatory function = G1 - defines the ready function instructionsAux function = M1 - definition of auxiliary function instructionX feedrate not used X -- definition of feed rate instructionY feedrate not used Y -- definition of feed rate instructionZ, feedrate, not, used -- define the Z feed rate instructionsCircle, angle, not, used -- circumferential angleX coordinate = X -- -- -- defines the X coordinate axis Y coordinate = Y -- -- -- defines the Y coordinate axis Z coordinate = Z -- -- -- defines the Z coordinate axis Key i = I - X - I bond axis vector definitionKey J = J - - Y axis vector JKey K = K - Z - K bond axis vector definitionFeedrate = F - - - defines feed rate instructionsFeedrate per revolution = F--- defines the feed rate instruction per turnSpindle = S -- -- -- defining spindle instructions chair number = t - - 定义刀具指令 ------ translated dwell not used ----------- 不使用循环停留 cycle--------------- 定义暂停时间键值 dwell = xlength = h ------------ 定义刀具长度补偿指令 chairthe chair ------------ 定义刀具半径补偿指令 radius = ddrill peck depth = q1 - - - - 钻孔的啄钻深度drill hole depth = z2 定义钻孔深度...----------- 定义安全平面高度 clearplane = r2.--------- 定义注释的开始符 message start = msmessage itself ----------- 定义注释的结束符 = emopskip = op - - - - --------- 定义跳段符号radius... -------- 键定义半径 r = rprogram id = id... - - - 定义程序号azimuth axis = b - - - - --------- 在多轴加工中, 定义方位轴elevation axis = c --------- 在多轴加工中, 定义仰角轴3rd rotation axis = zero... 在多轴加工中, 定义第三旋转轴not used (% 领导不使用 leaderthe x vector not used x矢量不使用 meddra system organ class y vector not used y矢量不使用 meddra system organ classz vector not used z矢量不使用 meddra system organ classerror 错误不使用 not used "define yourselfdefine ------------- --------- 定义指令值 codesrapid = 0 = = = = = g1 ---------- -------- 快速点定位linear = g1 = = = = = "1 直线插补circle cw = = = = = = g1 2 ------------- 顺圆插补circle ccw = = = = = = g1 3 ------------ 逆圆插补dwell = = = = ------------------- 暂停、准确停止 g6 4.the g3 xy plane = = = = = = = 17 平面 ------------- xyzy plane = = = = = = g3 19 --------- - - - - 平面 plastic tray xz plane = 18 = = = = = g3 平面 ------------- zxcompensation off = 40 = = ------ translated 取消刀具半径补偿g2compensation is left = = = = = 刀具半径左补偿 g2 41 compensation is right = g2 42 = = = 刀具半径右补偿imperial data = 20 = = = = = g4 --------- 英寸输入metric data 21 = = = = = g4 ---------- 毫米输入 = = =absolute data = = = = = ----------- g5 90 指定绝对坐标编程incremental data = = = = = -------- g5 91 指定增量坐标编程from = = = = = = g3 54 ------------------- 制定工作坐标系feedrate per minute not used = = = = = = 每分钟进给feedrate per revoluti not used = = = = = 每转进给spindle rpm not used 每分钟转速 meddra system organ classconstant surface speed not used 恒定的表面速度 ------ translateddrill = = = = = ------------------- g4 81 钻孔循环锪镗循环break the g4 chip = = = = --------------- 钻孔循环或反镗循环82deep drill = = = = = = g4 83 = ----------- 深孔钻循环tap = = = = = = g4 84 = = ------------------ 攻丝循环bore 85 = = = 1 = g4 --------------- 镗孔循环 = = = =the g4 bore 2 = = = = = = = 86 --------------- 镗孔循环the g4 bore 3 = = = = = = = 87 (% 背镗循环孔4 = 88 ====== ----------------镗孔循环G4孔5 = 89 ====== ----------------镗孔循环G4端钻= G4 80 ====== ----------固定循环取消宏开始不习惯======= ---------宏程序模态调用不使用===== -------------宏程序模态调用取消宏结束宏调用不使用======== ---------宏程序调用周期收回= G6 99 = = ------------固定循环返回到R点刀具长度偏置= = = = = ----- G3 43正向刀具长度补偿不使用========插补方式-------------花键花键停止0 = = = = = M1 ---------------------程序停止选择停止= M1 1 ===== ----------------选择停止在CW = M1 3 ===== -----------主轴正转主轴在CCW = M1 4 ===== ----------主轴逆转主轴主轴停止= M1 5 ===== -------------主轴停止自旋对CW = ----------------- M1 13冷却液旋转逆时针= ---------------- M1 14冷却液旋转冷却液= M1 5 = = = = --------冷却液关换刀= M1 6 ===== ------------自动换刀冷却液雾= = = = ----------雾状冷却液M1 7冷却液对M1 8 = = = = = ---------------冷却液开洪水= M1 8 = ------------冷却液开冷却剂（喷出）冷却液= M1 9 ===== -------------冷却液关夹在不使用------ -------------主轴锁紧不要用--------------------主轴锁紧不使用夹磁带结束= M1 2 ===== -------------程序结束结束程序= M1 30 ===== ------------程序结束1不使用----------------变速范围1不使用档2不使用----------------变速范围2不使用档3不使用----------------变速范围3不使用档恒定的速度不-----持续的轮廓速度不使用轮廓2不使用恒定轮廓速度----持续的轮廓速度2不使用字钻不------------------钻孔指令不使用字断屑不使用------------不使用断屑深不------------------孔深不使用字字不------------------冷却水不使用水龙头字孔1不使用---------------孔1不使用字孔2未使用字孔3未使用字孔4未使用字孔5未使用自来水不习惯-------------冷却液不使用冷却剂不使用====== -----------刚性攻丝刚性攻丝螺旋钻不------------螺旋钻孔螺旋收缩不------螺旋钻孔不使用钻最后定义===========================定义变量打印头=“Delcam后处理器”= = = =定义打印标题机器名称=“fanuc6m 1.2版”= = =机器名点==================================小数点零=“0”=============================零磁带头= 1 =======================纸带标题整数6 = 2 ====================== = = =定义冷却液开（M07、M08）的输出方式，此变量共有三个选项--0：在后处理时遇到相关指令时输出；1：在下一段中单独输出；2：在下一段中和坐标移动一起输出。
![ductpost后置处理进修资料[指南]](https://img.taocdn.com/s1/m/99f6ad1df68a6529647d27284b73f242336c3175.png)
