德国销及键标准对照表

序号德国标准中文品名Item DIN-Standard Description in Chinese 1DIN1圆锥销2DIN7圆柱销3DIN84开槽圆柱头螺钉4DIN85开槽盘头螺钉5DIN93单耳止动垫圈6DIN94开口销7DIN95开槽半沉头木螺钉8DIN96开槽半圆头木螺钉9DIN97开槽沉头木螺钉10DIN125-A平垫11DIN125-B平垫(带倒角)12DIN126平垫13DIN127-A重型弹垫14DIN127-B标准弹垫15DIN128-A鞍形弹垫16DIN137-A弹簧止动垫圈17DIN137-B波形弹垫18DIN186T型方颈螺栓19DIN188T型双接头螺栓20DIN258螺纹圆锥销21DIN261T型头螺栓22DIN315AF蝶形螺母(美制)23DIN315DF蝶形螺母(德制)24DIN316AF蝶形螺钉(美制)25DIN317DF蝶形螺钉(德制)26DIN319圆球型盖型螺母27DIN404开槽带孔球面圆柱头螺钉28DIN417开槽长圆柱端紧定螺钉29DIN427开槽平端紧定螺钉(半牙) 30DIN431小六角特薄细牙螺母31DIN432外舌止动垫圈32DIN433小垫圈(用于圆柱头螺钉) 33DIN434方斜垫圈(U型)34DIN435方斜垫圈(I型)35DIN436方垫圈36DIN438开槽凹端紧定螺钉37DIN439六角薄螺母38DIN439细牙六角薄螺母39DIN440木螺钉专用垫圈40DIN443密封帽41DIN444活节螺栓B型42DIN462内舌止动垫圈43DIN463双耳止动垫圈44DIN464滚花高头螺钉45DIN465开槽滚花高头螺钉46DIN466滚花高螺母47DIN467滚花薄螺母48DIN470锁紧垫圈49DIN471轴用弹性挡圈50DIN472孔用弹性档圈51DIN478方头带垫螺栓52DIN479方头圆柱底端螺栓53DIN480方头带垫半圆底端螺栓54DIN508T型槽螺母55DIN525单头螺柱56DIN529地脚螺栓57DIN546带槽圆螺母58DIN547端面带孔圆螺母59DIN551开槽平端紧定螺钉60DIN553开槽锥端紧定螺钉61DIN555六角螺母62DIN557方螺母－C63DIN558六角头螺钉65DIN562薄型方螺母—B66DIN571六角头木螺钉67DIN580吊环螺钉68DIN582吊环螺母69DIN601六角头螺栓70DIN603大半圆头方颈螺栓（马车螺栓)71DIN604沉头带插销马车螺栓72DIN605沉头长方颈马车螺栓73DIN607半圆头带插销马车螺栓74DIN608沉头短方颈马车螺栓75DIN609六角头精配螺栓(长螺纹) 76DIN610六角头精配螺栓(短螺纹) 77DIN653滚花平头螺钉64DIN561六角头圆柱端紧定螺钉78DIN660半圆头铆钉79DIN661沉头铆钉80DIN662半沉头铆钉81DIN674大扁头铆钉82DIN703重型侧面带孔圆螺母83DIN705侧面带孔圆螺母84DIN741卡头85DIN787T型槽螺钉86DIN835双头螺柱(牙长＝2D) 87DIN906内六角锥型闭锁螺钉88DIN908内六角直型闭锁螺钉89DIN909外六角锥型闭锁螺钉90DIN910外六角直型闭锁螺钉91DIN911内六角扳手92DIN912内六角圆柱头螺钉93DIN913内六角平端紧定螺钉94DIN914内六角尖端紧定螺钉95DIN915内六角圆柱端紧定螺钉96DIN916内六角凹端紧定螺钉97DIN917薄型盲螺母98DIN920开槽小圆柱头螺钉99DIN921开槽大圆柱头螺钉100DIN923开槽圆柱头轴肩螺钉101DIN927开槽无头轴肩螺钉102DIN928焊接方螺母103DIN929焊接六角螺母104DIN931六角头螺栓(半牙) 105DIN933六角头螺栓(全牙) 106DIN934六角头螺母(1型) 107DIN934细牙六角头螺母(1型) 108DIN935开槽六角螺母109DIN936六角头薄螺母110DIN937六角头开槽薄螺母111DIN938双头螺距(牙长＝1D) 112DIN939双头螺距(牙长＝1.25D) 113DIN940双头螺距(牙长＝1.5D) 114DIN960六角头细牙螺栓(半牙) 115DIN961六角头细牙螺栓(全牙) 116DIN962头部穿孔六角头螺栓117DIN963开槽沉头螺钉118DIN964开槽半沉头螺钉119DIN965十字槽沉头螺钉120DIN966十字槽半沉头螺钉121DIN970六角头螺母122DIN971六角头螺母123DIN972细牙六角头螺母(2型) 124DIN975牙条(全螺纹)125DIN976螺纹销126DIN979六角头开槽薄螺母(2型)127DIN980全金属六角锁紧螺母(1型) 128DIN981圆螺母129DIN982六角头尼龙锁紧螺母130DIN985六角头薄型尼龙锁紧螺母131DIN986六角盖型尼龙锁紧螺母132DIN988配合垫片133DIN1052木材连接用垫片134DIN1151沉头钢钉135DIN1440销钉专用垫片A型136DIN1441销钉专用垫片137DIN1444带头销钉138DIN1471圆锥型槽销139DIN1472圆锥型槽销(半槽) 140DIN1473平行槽销(带倒角) 141DIN1474前端凹槽槽销142DIN1475中部凹槽槽销143DIN1476圆头槽销144DIN1477沉头槽销145DIN1479六角螺母棒146DIN1480花篮螺栓147DIN1481弹性圆柱销148DIN1587组合式盖型螺母149DIN1804开槽圆螺母(配合沟头扳手) 150DIN1816圆螺母(带插销孔) 151DIN2093盘型弹簧垫圈152DIN3017喉箍153DIN3404润滑油嘴(旋扭头)154DIN3567管夹155DIN3570U型螺栓156DIN6319球面垫圈157DIN6325圆柱销158DIN6330厚六角螺母159DIN6331厚六角法兰面螺母160DIN6334长六角螺母161DIN6797-A外齿锁紧垫圈162DIN6797-1内齿锁紧垫圈163DIN6798-A外锯齿锁紧垫圈164DIN6798-1内锯齿锁紧垫圈165DIN6799开口挡圈166DIN6885平键(A型)167DIN6888半圆键168DIN6899嵌环(支撑环)169DIN6900机器螺钉和垫圈组合件170DIN6901自攻螺钉和垫圈组合件171DIN6912薄型带孔内六角圆柱头螺钉174DIN6916大垫圈175DIN6917楔型方垫圈176DIN6923六角法兰面螺母177DIN6925全金属六角锁紧螺母(2型)178DIN7337开口型抽芯铆钉(沉头 、扁圆头)179DIN7338扁平头半空心/全空心铆钉180DIN7343螺旋夹紧销181DIN7346轻型弹性圆柱销182DIN7349重型弹性圆柱销用垫圈183DIN7500ISO公制螺纹螺钉(多种头型)184DIN7504自攻自钻螺钉(多种头型) 185DIN7513开槽切削螺纹螺钉(多种头型)186DIN7516十字槽切削螺纹螺钉(多种头型)173DIN6915大六角螺母172DIN6914大六角头螺栓187DIN7965T型四爪螺母188DIN7968钢结构用六角头螺栓连接副189DIN7971开槽盘头自攻螺钉190DIN7972开槽沉头自攻螺钉191DIN7973开槽半沉头自攻螺钉192DIN7976六角头自攻螺钉193DIN7980圆柱头螺钉用弹簧垫圈194DIN7981十字槽盘头自攻螺钉195DIN7982十字槽沉头自攻螺钉196DIN7983十字槽半沉头自攻螺钉197DIN7984薄型内六角圆柱头螺钉198DIN7985十字槽盘头螺钉199DIN7989钢结构用垫圈200DIN7990钢结构用六角头螺栓201DIN7991内六角沉头螺钉202DIN7993轴用钢丝挡圈203DIN7995十字槽半沉头木螺钉204DIN7996十字槽圆头木螺钉205DIN7997十字槽沉头木螺钉206DIN8140螺纹护套(普通\自锁等) 207DIN9021大外径垫圈208DIN11024弹簧卡子209DIN13257平板螺栓210DIN18182干壁钉(墙板钉)211DIN28129环型螺母212DIN70952圆螺母用止退垫圈英文品名国际标准中国标准Description in English ISO-Standard GB-Standard Taper pins ISO2339GB117Parallel pins ISO2338GB119-86 Slotted cheese head screws ISO1207GB65-85Slotted pan head screws ISO1580GB67-85 Tab washers GB854Split cotter pins ISO1234GB91 Slotted raised csk head wood screws GB101 Slotted round head wood screws GB99 Slotted raised csk head wood screws GB100 Plain washers ISO7089GB97.1-85Mediun washers ISO7090GB97.2-85Plain washers ISO7091Spring lock washers tang ends GB7244 Spring lock washers square ends GB93-87 Single coil spring lock washers GB7245-87 Curved spring washersWave spring washers GB955 T-head bolts with square neck GB37-88 T-head bolts with double nipTaper pins with threaded end ISO8737T-head boltsWing nuts amercia formWing nuts germany form GB62-88Wing screws amercia formWing screws germany formBall knobsSlotted capstan screws GB832-88 Slotted set srews with full dog point ISO7435GB75-85 Slotted set srews with chamfered end ISO2342GB73-85 Pipe nuts with thread GB808-88 External tap GB856-88 Washers for cheese head screws ISO7092GB848-95 Square taper washers for U-section GB852-88 Square taper washers for I-section GB852-88 Square washersSlotted set with cup point ISO7436GB74-85 Hexagon thin nuts ISO4035GB6172-86Hexagon thin nuts ISO8675GB6173-86 Rounds washers for wood constructions ISO7094Sealing caps, push –in typeEye bolts form B GB798-88Internal tab washersWashers with two taps GB855-88 Knurled thumb screws with collar GB834-88 Slotted knurled thumb screws with collarKnurled thumb nuts with collar GB806-88 Knurled thumb thin nuts GB807-88 Sealing washersRetaining rings for shafts(external),circlips GB894.1-86 Retaining rings for bores(internal), circlips GB893.1-86 Square head bolts with collarSquare head bolts with half dog pointSquare head bolts with collar,half dog point and rounded endT-solt nuts ISO299Single end studsMasonry bolts GB799-88Slotted round nuts GB817-76 Round nuts with drilled holes in one face GB815-88 Slotted sit screws with flat point ISO4776GB73-85 Slotted set screws with cone point ISO7434GB71-85 Hexagon nuts ISO4034Square nuts GB39-88Hexagon screws ISO4018Hexagon set screwswith full dog pointSquare nuts without bevel(pressed nuts)Hexagon head wood screws (coach screws)GB102-86 Lifting eye bolts ISO3266GB825-76Lifting eye nutsHexagon bolts ISO4016Mushroom head square neck boltISO8677GB14-88 (carriage bolts)Falt countersunk nib boltsFalt countersunk long square neck boltsCup head nib boltsFalt countersunk short square neck boltsHexagon fitted bolts, long theadHexagon fitted bolts, short theadKnurled thumb screws thin type GB835-88Round head rivets ISO1051GB867-86Contersunk head rivets ISO1051GB869-86 Raised contersunk head rivets ISO1051Mushroom head rivets ISO1051Adjusting rings,heavy range(shafting collars)Adjusting rings,light range(shafting collars)GB816-88 Wire rope clipsT-slot screws ISO299Studs-metal (end=2d)GB900-88 Hexagon socket pipe plugs ,conical threedHexagon socket screw plugs , cyl. ThreadHexagon head pipe plugs, conical threadHexagon head pipe plugs , cyl . threedSocket wrendches ISO2936Hexagon socket cap screws ISO4762GB70-85 Hexagon socket set screws with flat point ISO4026GB77-85 Hexagon socket set screws with cone point ISO4027GB78-85 Hexagon socket set screws with dog point ISO4028GB79-85 Hexagon socket set screws with cup point ISO4029GB80-85 Hexagon cap nutsSlotted short cheese head screwsSlotted large cheese head screws GB838-88 Slotted pan head screws with shoulder GB830-88 Slotted shoulder screwsSquare weld nuts GB/T13680-92Hexagon weld nuts GB/T13681-92Hexagon head screws ISO4014GB5782-86Hexagon head screws ISO4017GB5783-86Hexagon full nuts ISO4032GB6170-86Hexagon full nuts ISO8673GB6171-86 Hexagon slotted and castle nuts ISO7035GB6178-86 Hexagon thin nuts ISO4035GB6172.1-86 Hexagon thin slotted and castle nuts ISO7038GB6181-86 Studs metal (end=1d)GB897-88Studs metal (end=1.25d)GB898-88Studs metal (end=1.5d)Hexagon head bolts, metric fine pitch thread ISO8765GB5785-86 Hexagon head bolts, metric fine pitch thread ISO8676GB5786-86 Additional shapes and versions for boltsSlottded countersund head screws ISO 2009GB68-85 Slottded raised countersunk oval head screws ISO 2010GB69-85Cross recessed countersunk heads crews ISO7046GB819-85 Cross recessed raised countersunk heads crews ISO7047GB820-85 Hexagon nuts type-1Hexagon nuts type-2Hexagon nuts with fine thread ISO8674GB6176-86Threaded rods (studdings)GB15389-94Threaded pins (stud bolts)Hexagon thin slotted and castle nutsPrevailing torque type hexagon nuts,ISO7199GB6184-86 all metall nutsLocknuts ISO2982GB812-88Prevailing torque type hexagon nuts,ISO7040GB889.1-86 heavy type with nylon insertPrevailing torque type hexagon nuts,ISO10511GB6172.2-86 heavy type with nylon insertPrevailing torque typedomedcapnuts with nylon insertShim ringsWashers for timber connectorsRound plain head nailsPlain washer for clevis pins(A型)ISO8738Plain washer for clevis pinsclevis pins with head ISO2341Grooved pins, taper grooved ISO8744GB/T13829.2 Grooved pins, taper grooved half length ISO8745GB/T13829.2 Grooved pins, parallel grooved full length ISO8740Grooved pins, reserve grooved half length ISO8741Grooved pins, centre grooved ISO8742Grooved pins with round head ISO8746GB/T13829.2 Grooved pins with countersunk head ISO8747Turnuckles(centre parts)Made out of hexagon barTurnuckles with eye bolt and hock boltSpring pins,heavy type ISO8752GB879-86Hexagon domed cap nuts GB802-88 Slotted round nuts for hook spannerRound nuts with set holesDisc springsHose clampsLubricating nipples,button headShackles for conduiltsStirrup bolts(U-bolts)Spherical washers, conical seats GB849-88 Parallel pins ISO8734Hexagon nuts , 1.5d GB56-88 Hexagon nuts, 1.5d with collar GB6177-86 Hexagon nuts , 3dExternal teeth lock washers GB862.1-87Internal teeth lock washers GB861.1-87 External teeth serrated lock washers GB862.2-87 Internal teeth serrated lock washers GB861.2-87 Retaining ring for shafrs(Ering), circlips GB896-76 Parallel keys (form A)ISO773/2491Woodruff keys ISO3912ThimblesScrews and washers assemblies GB9074.1-17 Tapping screws and washers assemblies GB9074.18-23 Hexagon socket head cap screwswith hole, low headHexagon head bolts with large head(friction grip bolts)Hexagon nuts with large wideth acrossflat(friction grip nuts)Round washers for friction grip boltsSpuaretaper washers for frictiongrip bolts on T-sectionsHexagon flange nuts ISO4161GB6177-86 Prevailing torque type hexagon nuts ,all metallicISO7042GB6185.1-2000nutsBlind rivets GB12617/12618 Rivets for brake and clutch lining GB875/975-86 Spiral pins ISO8750Spring pins,light type ISO13337Washers for bolts with heavy type spring pinssThreadforming screws for ISO-metric threadSelf-drilling tapping screwsThread cutting screwsThread cutting screws cross recessTee nuts with prongeHexagon head fitted bolts for steel structures GB1228/1229/1230 Pan head tapping screws with slot ISO1481GB5282-85 Countersunk flat head tapping screws with slot ISO1482GB5283-85Raised countersunk oval head tapping screwsISO1483GB5284-85with slotHexagon tapping screws ISO1479GB5285-85Spring lock washers for screws with cylindricalISO8738headsPan head tapping screws with cross recessed ISO 7049GB845-85Countersunk flat head tapping screws with crossISO7050GB846-85recessedRaised countersunk flat head tapping screwsISO7051GB847-86 with cross recessedHexagon socket head cap screws with reducedheadPan head screws with cross recessed ISO7045GB818-85 Washers for steel structures GB1230-84 Hexagon head bolts for steel structures GB1229-84 Hexagon socket countersunk head scriws ISO10642Roundwire snap rings for shafts GB895.2-86Cross recessed raised countersunk head woodGB952-86screwsCross recessed round head wood screws GB950-86 Cross recessed countersunk head wood screws GB951-86 Ciol inserts, coarse,fine thread, silf lockingWashers,outside diameter appro.3d ISO7093GB96-85 Spring cotter for a boltBelting bolts (elevator bolts)Dry wall screwsLifting nuts(eye nuts)GB63-88 Tab washers for slotted round nuts GB858-88。

德标与国标对照表德标与国标对照表德国标准（DIN）和中国国家标准（GB）是两个不同国家的标准化组织所制定的标准。

虽然有相似之处，但在某些领域有所不同。

以下是德标与国标的对照表。

一、电气工程1. 电线和电缆德标：DIN VDE 0250国标：GB 50232. 无绝缘导体德标：DIN EN 60228国标：GB/T 39563. 低压电器德标：DIN EN 60 439-1 国标：GB 14048.14. 高压开关设备德标：DIN 43620国标：GB 19845. 潜水电泵德标：DIN 24255国标：GB/T 281-2004二、机械工程1. 标准零件德标：DIN 931/1国标：GB/T 57822. 对焊接德标：DIN 8563/1-3国标：GB/T 985-1998 3. 货物运输德标：DIN 15185国标：GB/T 121834. 机床德标：DIN 863国标：GB/T 108605. 尺寸公差德标：DIN EN ISO 2768 国标：GB/T 1804-2000 三、建筑工程1. 路面标准德标：DIN 18035国标：GB 504872. 接缝放样德标：DIN 18202国标：GB 505813. 钢筋连接德标：DIN 1045国标：GB 14994. 建筑钢材德标：DIN 488国标：GB/T 706-1988 5. 水泥制品德标：DIN 18550国标：GB/T 11785以上是德标与国标的对照表，可以看到，在不同领域，德标与国标相比有些区别。

因此，在进行相关工程和产品设计时，需要根据当地标准进行设计和生产，以满足当地需求。

德国标准和国际标准、中国标准中英文对照表序号德国标准中文品名英文品名国际标准中国标准Item DIN-Standard Description in Chinese Description in English ISO-Standard GB-Standard1 DIN1 圆锥销taper pins ISO2339 GB1172 DIN7 圆柱销parallel pins ISO2338 GB119-863 DIN84 开槽圆柱头螺钉slotted cheese head screws ISO1207 GB65-854 DIN85 开槽盘头螺钉slotted pan head screws ISO1580 GB67-855 DIN93 单耳止动垫圈tab washers GB8546 DIN94 开口销split cotter pins ISO1234 GB917 DIN95 开槽半沉头木螺钉slotted raised csk head wood screws GB1018 DIN96 开槽半圆头木螺钉slotted round head wood screws GB999 DIN97 开槽沉头木螺钉slotted countersunk head wood screws GB10010 DIN125-A 平垫plain washers ISO7089 GB97.1-8511 DIN125-B 平垫(带倒角) mediun washers ISO7090 GB97.2-8512 DIN126 平垫plain washers ISO709113 DIN127-A 重型弹垫spring lock washers,tang ends GB724414 DIN127-B 标准弹垫spring lock washers,square ends GB93-8715 DIN128-A 鞍形弹垫single coil spring lock washers GB7245-8716 DIN137-A 弹簧止动垫圈curved spring washers17 DIN137-B 波形弹垫wave spring washers GB95518 DIN186 T型方颈螺栓T-head bolts with square neck GB37-8819 DIN188 T型双接头螺栓T-head bolts with double nip20 DIN258 螺纹圆锥销taper pins with threaded end ISO873721 DIN261 T型头螺栓T-head bolts22 DIN315AF 蝶型螺母(美制) wing nuts amercia form23 DIN315DF 蝶型螺母(德制) wing nuts germany form GB62-8824 DIN316AF 蝶型螺钉(美制) wing screws amercia form25 DIN317DF 蝶型螺钉(德制) wing screws germany form26 DIN319 圆球型盖型螺母ball knobs27 DIN404 开槽带孔球面圆柱头螺钉slotted capstan screws GB832-8828 DIN417 开槽长圆柱端紧定螺钉slotted set srews with full dog point ISO7435 GB75-8529 DIN427 开槽平端紧定螺钉(半牙) slotted set srews with chamfered end ISO2342 GB73-8530 DIN431 小六角特薄细牙螺母pipe nuts with thread GB808-8831 DIN432 外舌止动垫圈external tap GB856-8832 DIN433 小垫圈(用于圆柱头螺钉) washers for cheese head screws ISO7092 GB848-9533 DIN434 方斜垫圈(U型) square taper washers for U-section GB852-8834 DIN435 方斜垫圈(I型) square taper washers for I-sections GB852-8835 DIN436 方垫圈square washers36 DIN438 开槽凹端紧定螺钉slotted set with cup point ISO7436 GB74-8537 DIN439 六角薄螺母hexagon thin nuts ISO4035 GB6172-8638 DIN439 细牙六角薄螺母hexagon thin nuts ISO8675 GB6173-8639 DIN440 木螺钉专用垫圈rounds washers for wood constructions ISO709440 DIN443 密封帽sealing caps,push-in type41 DIN444 活节螺栓B 型eye bolts form B GB798-8842 DIN462 内舌止动垫圈internal tab washers43 DIN463 双耳止动垫圈washers with two taps GB855-8844 DIN464 滚花高头螺钉knurled thumb screws with collar GB834-8845 DIN465 开槽滚花高头螺钉slotted knurled thumb screws with collar46 DIN466 滚花高螺母knurled thumb nuts with collar GB806-8847 DIN467 滚花薄螺母knurled thumb thin nuts GB807-8848 DIN470 锁紧垫圈sealing washers49 DIN471 轴用弹性挡圈retaining rings for shafts(external),circlips GB894.1-8650 DIN472 孔用弹性挡圈retaining rings for bores(internal),circlips GB893.1-8651 DIN478 方头带垫螺栓square head bolts with collar52 DIN479 方头圆柱底端螺栓square head bolts with half dog point53 DIN480 方头带垫半圆底端螺栓square head bolts with collar,half dog point and rounded end54 DIN508 T型槽螺母T-slot nuts ISO29955 DIN525 单头螺柱single end studs56 DIN529 地脚螺栓masonry bolts GB799-8857 DIN546 带槽圆螺母slotted round nuts GB817-7658 DIN547 端面带孔圆螺母round nuts with drilled holes in one face GB815-8859 DIN551 开槽平端紧定螺钉slotted sit screws with flat point ISO4776 GB73-8560 DIN553 开槽锥端紧定螺钉slotted set screws with cone point ISO7434 GB71-8561 DIN555 六角螺母hexagon nuts ISO403462 DIN557 方螺母-C square nuts GB39-8863 DIN558 六角头螺钉hexagon screws ISO401864 DIN561 六角头圆柱端紧定螺钉hexagon set screws with full dog point65 DIN562 薄型方螺母-B square nuts without bevel(pressed nuts)66 DIN571 六角头木螺钉hexagon head wood screws (coach screws) GB102-8667 DIN580 吊环螺钉lifting eye bolts ISO3266 GB825-7668 DIN582 吊环螺母lifting eye nuts69 DIN601 六角头螺栓hexagon bolts ISO401670 DIN603 大半圆头方颈螺栓(马车螺栓) mushroom head square neck bolts (carriage bolts) ISO8677 GB14-8871 DIN604 沉头带插销马车螺栓flat countersunk nib bolts72 DIN605 沉头长方颈马车螺栓flat countersunk long square neck bolts73 DIN607 半圆头带插销马车螺栓cup head nib bolts74 DIN608 沉头短方颈马车螺栓flat countersunk short square neck bolts75 DIN609 六角头精配螺栓（长螺纹）hexagon fitted bolts,long thread76 DIN610 六角头精配螺栓（短螺纹）hexagon fitted bolts,short thread77 DIN653 滚花平头螺钉knurled thumb screws thin type GB835-8878 DIN660 半圆头铆钉round head rivets ISO1051 GB867-8679 DIN661 沉头铆钉contersunk head rivets ISO1051 GB869-8680 DIN662 半沉头铆钉raised contersunk head rivets ISO105181 DIN674 大扁头铆钉mushroom head rivets ISO105182 DIN703 重型侧面带孔圆螺母adjusting rings,heavy range (shafting collars)83 DIN705 侧面带孔圆螺母adjusting rings,light range (shafting collars) GB816-8884 DIN741 卡头wire rope clips85 DIN787 T型槽螺钉T-slot screws ISO29986 DIN835 双头螺柱（牙长=2D）studs-metal (end=2d) GB900-8887 DIN906 内六角锥型闭锁螺钉hexagon socket pipe plugs,conical thread88 DIN908 内六角直型闭锁螺钉hexagon socket screw plugs,cyl. thread89 DIN909 外六角锥型闭锁螺钉hexagon head pipe plugs,conical thread90 DIN910 外六角直型闭锁螺钉hexagon head screw plugs,cyl.thread91 DIN911 内六角扳手socket wrenches ISO293692 DIN912 内六角圆柱头螺钉hexagon socket cap screws ISO4762 GB70-8593 DIN913 内六角平端紧定螺钉hexagon socket set screws with flat point ISO4026 GB77-8594 DIN914 内六角尖端紧定螺钉hexagon socket set screws with cone point ISO4027 GB78-8595 DIN915 内六角圆柱端紧定螺钉hexagon socket set screws with dog point ISO4028 GB79-8596 DIN916 内六角凹端紧定螺钉hexagon socket set screws with cup point ISO4029 GB80-8597 DIN917 薄型盲螺母hexagon cap nuts98 DIN920 开槽小圆柱头螺钉slotted short cheese head screws99 DIN921 开槽大圆柱头螺钉slotted large cheese head screws GB838-88100 DIN923 开槽圆柱头轴肩螺钉slotted pan head screws with shoulder GB830-88101 DIN927 开槽无头轴肩螺钉slotted shoulder screws102 DIN928 焊接方螺母square weld nuts GB/T13680-92103 DIN929 焊接六角螺母hexagon weld nuts GB/T13681-92104 DIN931 六角头螺栓（半牙）hexagon head screws ISO4014 GB5782-86105 DIN933 六角头螺栓（全牙）hexagon head screws ISO4017 GB5783-86106 DIN934 六角头螺母(1型) hexagon full nuts ISO4032 GB6170-86107 DIN934 细牙六角头螺母(1型) hexagon full nuts ISO8673 GB6171-86108 DIN935 开槽六角螺母hexagon slotted and castle nuts ISO7035 GB6178-86109 DIN936 六角头薄螺母hexagon thin nuts ISO4035 GB6172.1-86110 DIN937 六角头开槽薄螺母hexagon thin slotted and castle nuts ISO7038 GB6181-86111 DIN938 双头螺距（牙长=1D）studs metal (end=1d) GB897-88112 DIN939 双头螺距（牙长=1.25D）studs metal (end=1.25d) GB898-88113 DIN940 双头螺距（牙长=1.5D）studs metal (end=1.5d)114 DIN960 六角头细牙螺栓（半牙）hexagon head bolts,metric fine pitch thread ISO8765 GB5785-86115 DIN961 六角头细牙螺栓（全牙）hexagon head bolts,metric fine pitch thread ISO8676 GB5786-86116 DIN962 头部穿孔六角头螺栓additional shapes and versions for bolts117 DIN963 开槽沉头螺钉slotted countersund head screws ISO 2009 GB68-85118 DIN964 开槽半沉头螺钉slotted raised countersunk oval head screws ISO 2010 GB69-85 119 DIN965 十字槽沉头螺钉cross recessed countersunk head screws ISO7046 GB819-85120 DIN966 十字槽半沉头螺钉cross recessed raised countersunk head screws ISO7047 GB820-85121 DIN970 六角头螺母hexagon nuts type-1122 DIN971 六角头螺母hexagon nuts type-2123 DIN972 细牙六角头螺母(2型) hexagon nuts with fine thread ISO8674 GB6176-86124 DIN975 牙条(全螺纹) threaded rods(studdings) GB15389-94125 DIN976 螺纹销threaded pins(stud bolts)126 DIN979 六角头开槽薄螺母（2型）hexagon thin slotted and castle nuts127 DIN980 全金属六角锁紧螺母（1型）prevailling torque type hexagon nuts,all metall nuts ISO7199 GB6184-86128 DIN981 圆螺母locknuts ISO2982 GB812-88129 DIN982 六角头尼龙锁紧螺母prevailling torque type hexagon nuts,heavy type ,with nylon insert ISO7040 GB889.1-86130 DIN985 六角头薄型尼龙锁紧螺母prevailling torque type hexagon nuts,heavy type ,with nylon insert ISO10511 GB6172.2-86131 DIN986 六角盖型尼龙锁紧螺母prevailling torque typedomed capnuts with nylon insert132 DIN988 配合垫片shim rings133 DIN1052 木材连接用垫片washers for timber connectors134 DIN1151 沉头钢钉round plain head nails135 DIN1440 销钉专用垫片A型plain washers for clevis pins(A型) ISO8738136 DIN1441 销钉专用垫片plain washers for clevis pins137 DIN1444 带头销钉clevis pins with head ISO2341138 DIN1471 圆锥型槽销grooved pins,taper grooved ISO8744 GB/T13829.2139 DIN1472 圆锥型槽销(半槽) grooved pins,taper grooved half length ISO8745 GB/T13829.2 140 DIN1473 平行槽销(带倒角) grooved pins,parallel grooved full length ISO8740141 DIN1474 前端凹槽槽销grooved pins,reserve grooved half length ISO8741142 DIN1475 中部凹槽槽销grooved pins,centre grooved ISO8742143 DIN1476 圆头槽销grooved pins with round head ISO8746 GB/T13829.3144 DIN1477 沉头槽销grooved pins with countersunk head ISO8747145 DIN1479 六角螺母棒turnuckles(centre parts),made out of hexagon bar146 DIN1480 花篮螺栓turnuckles with eye bolt and hook bolt147 DIN1481 弹性圆柱销spring pins,heavy type ISO8752 GB879-86148 DIN1587 组合式盖型螺母hexagon domed cap nuts GB802-88149 DIN1804 开槽圆螺母（配合沟头扳手）slotted round nuts for hook spanner150 DIN1816 圆螺母（带插销孔）round nuts with set holes151 DIN2093 盘型弹簧垫圈disc springs152 DIN3017 喉箍hose clamps153 DIN3404 润滑油嘴（旋扭头）lubricating nipples,button head154 DIN3567 管夹shackles for conduilts155 DIN3570 U型螺栓stirrup bolts(U-bolts)156 DIN6319 球面垫圈spherical washers,conical seats GB849-88157 DIN6325 圆柱销parallel pins ISO8734158 DIN6330 厚六角螺母hexagon nuts ,1.5d GB56-88159 DIN6331 厚六角法兰面螺母hexagon nuts ,1.5d with collar GB6177-86160 DIN6334 长六角螺母hexagon nuts ,3d161 DIN6797-A 外齿锁紧垫圈external teeth lock washers GB862.1-87162 DIN6797-I 内齿锁紧垫圈internal teeth lock washers GB861.1-87163 DIN6798-A 外锯齿锁紧垫圈external teeth serrated lock washers GB862.2-87164 DIN6798-I 内锯齿锁紧垫圈internal teeth serrated lock washers GB861.2-87165 DIN6799 开口挡圈retaining rings for shafts(E-rings),circlips GB896-76166 DIN6885 平键（A型）parallel keys(form A ) ISO773/2491167 DIN6888 半圆键woodruff keys ISO3912168 DIN6899 嵌环（支撑环）thimbles169 DIN6900 机器螺钉和垫圈组合件screws and washers assemblies GB9074.1-.17170 DIN6901 自攻螺钉和垫圈组合件tapping screws and washers assemblies GB9074.18-.23 171 DIN6912 薄型带孔内六角圆柱头螺钉hexagon socket head cap screws with hole,low head 172 DIN6914 大六角头螺栓hexagon head bolts with large head(friction grip bolts)173 DIN6915 大六角螺母hexagon nuts with large wideth across flat(friction grip nuts)174 DIN6916 大垫圈round washers for friction grip bolts175 DIN6917 楔型方垫圈spuare taper washers for friction grip bolts on T-sections176 DIN6923 六角法兰面螺母hexagon flange nuts ISO4161 GB6177-86177 DIN6925 全金属六角锁紧螺母(2型）prevailing torque type hexagon nuts,all metallic nuts ISO7042 GB6185.1-2000178 DIN7337 开口型抽芯铆钉（沉头、扁圆头）blind rivets GB12617/12618179 DIN7338 扁平头半空心/全空心铆钉rivets for brake and clutch lining GB875/975-86180 DIN7343 螺旋夹紧销spiral pins ISO8750181 DIN7346 轻型弹性圆柱销spring pins,light type ISO13337182 DIN7349 重型弹性圆柱销用垫圈washers for bolts with heavy type spring pinss183 DIN7500 ISO公制螺纹螺钉(多种头型) threadforming screws for ISO-metric thread184 DIN7504 自攻自钻螺钉(多种头型) self-drilling tapping screws185 DIN7513 开槽切削螺纹螺钉(多种头型) thread cutting screws186 DIN7516 十字槽切削螺纹螺钉(多种头型) thread cutting screws cross recess187 DIN7965 T型四爪螺母tee nuts with pronge188 DIN7968 钢结构用六角头螺栓连接副hexagon head fitted bolts for steel structures GB1228/1229/1230189 DIN7971 开槽盘头自攻螺钉pan head tapping screws with slot ISO1481 GB5282-85190 DIN7972 开槽沉头自攻螺钉countersunk flat head tapping screws with slot ISO1482 GB5283-85191 DIN7973 开槽半沉头自攻螺钉raised countersunk oval head tapping screws with slot ISO1483 GB5284-85192 DIN7976 六角头自攻螺钉hexagon tapping screws ISO1479 GB5285-85193 DIN7980 圆柱头螺钉用弹簧垫圈spring lock washers for screws with cylindrical heads ISO8738194 DIN7981 十字槽盘头自攻螺钉pan head tapping screws with cross recessed ISO 7049 GB845-85195 DIN7982 十字槽沉头自攻螺钉countersunk flat head tapping screws with cross recessed ISO7050 GB846-85196 DIN7983 十字槽半沉头自攻螺钉raised countersunk oval head tapping screws with cross recessed ISO7051 GB847-86197 DIN7984 薄型内六角圆柱头螺钉hexagon socket head cap screws with，reduced head198 DIN7985 十字槽盘头螺钉pan head screws with cross recessed ISO7045 GB818-85199 DIN7989 钢结构用垫圈washers for steel structures GB1230-84200 DIN7990 钢结构用六角头螺栓hexagon head bolts for steel structures GB1229-84201 DIN7991 内六角沉头螺钉hexagon socket countersunk head screws ISO10642202 DIN7993 轴用钢丝挡圈roundwire snap rings for shafts GB895.2-86203 DIN7995 十字槽半沉头木螺钉cross recessed raised countersunk head wood screws GB952-86204 DIN7996 十字槽圆头木螺钉cross recessed round head wood screws GB950-86205 DIN7997 十字槽沉头木螺钉cross recessed countersunk head wood screws GB951-86206 DIN8140 螺纹护套（普通\自锁等）ciol inserts,coarse,fine thread,silf locking207 DIN9021 大外径垫圈washers,outside diameter appro.3d ISO7093 GB96-85208 DIN11024 弹簧卡子spring cotter for a bolt209 DIN13257 平板螺栓belting bolts (elevator bolts)210 DIN18182 干壁钉（墙板钉）dry wall screws211 DIN28129 环型螺母lifting nuts(eye nuts) GB63-88212 DIN70952 圆螺母用止退垫圈tab washers for slotted round nuts GB858-88。

序号德国标准中文品名国际标准中国标准1DIN1圆锥销ISO2339GB1172DIN7圆柱销ISO2338GB119-863DIN84开槽圆柱头螺钉ISO1207GB65-854DIN85开槽盘头螺钉ISO1580GB67-855DIN93单耳止动垫圈GB8546DIN94开口销ISO1234GB917DIN95开槽半沉头木螺钉GB1018DIN96开槽半圆头木螺钉GB999DIN97开槽沉头木螺钉GB10010DIN125-A平垫ISO7089GB97.1-8511DIN125-B平垫(带倒角)ISO7090GB97.2-8512DIN126平垫ISO709113DIN127-A重型弹垫GB724414DIN127-B标准弹垫GB93-8715DIN128-A鞍形弹垫GB7245-8716DIN137-A弹簧止动垫圈17DIN137-B波形弹垫GB95518DIN186T型方颈螺栓GB37-8819DIN188T型双接头螺栓20DIN258螺纹圆锥销ISO873721DIN261T型头螺栓22DIN315AF蝶形螺母(美制)23DIN315DF蝶形螺母(德制)GB62-8824DIN316AF蝶形螺钉(美制)25DIN317DF蝶形螺钉(德制)26DIN319圆球型盖型螺母27DIN404开槽带孔球面圆柱头螺钉GB832-8828DIN417开槽长圆柱端紧定螺钉ISO7435GB75-8529DIN427开槽平端紧定螺钉(半牙)ISO2342GB73-8530DIN431小六角特薄细牙螺母GB808-8831DIN432外舌止动垫圈GB856-88序号德国标准中文品名国际标准中国标准32DIN433小垫圈(用于圆柱头螺钉)ISO7092GB848-9533DIN434方斜垫圈(U型)GB852-8834DIN435方斜垫圈(I型)GB852-8835DIN436方垫圈36DIN438开槽凹端紧定螺钉ISO7436GB74-8537DIN439六角薄螺母ISO4035GB6172-8638DIN439细牙六角薄螺母ISO8675GB6173-8639DIN440木螺钉专用垫圈ISO709440DIN443密封帽41DIN444活节螺栓B型GB798-8842DIN462内舌止动垫圈43DIN463双耳止动垫圈GB855-8844DIN464滚花高头螺钉GB834-8845DIN465开槽滚花高头螺钉46DIN466滚花高螺母GB806-8847DIN467滚花薄螺母GB807-8848DIN470锁紧垫圈49DIN471轴用弹性挡圈GB894.1-8650DIN472孔用弹性档圈GB893.1-8651DIN478方头带垫螺栓52DIN479方头圆柱底端螺栓53DIN480方头带垫半圆底端螺栓54DIN508T型槽螺母ISO29955DIN525单头螺柱56DIN529地脚螺栓GB799-8857DIN546带槽圆螺母GB817-7658DIN547端面带孔圆螺母GB815-8859DIN551开槽平端紧定螺钉ISO4776GB73-8560DIN553开槽锥端紧定螺钉ISO7434GB71-8561DIN555六角螺母ISO403462DIN557方螺母－C GB39-88序号德国标准中文品名国际标准中国标准63DIN558六角头螺钉ISO401864DIN561六角头圆柱端紧定螺钉65DIN562薄型方螺母-B66DIN571六角头木螺钉GB102-8667DIN580吊环螺钉ISO3266GB825-7668DIN582吊环螺母69DIN601六角头螺栓ISO401670DIN603大半圆头方颈螺栓ISO8677GB14-8871DIN604沉头带插销马车螺栓72DIN605沉头长方颈马车螺栓73DIN607半圆头带插销马车螺栓74DIN608沉头短方颈马车螺栓75DIN609六角头精配螺栓(长螺纹)76DIN610六角头精配螺栓(短螺纹)77DIN653滚花平头螺钉GB835-8878DIN660半圆头铆钉ISO1051GB867-8679DIN661沉头铆钉ISO1051GB869-8680DIN662半沉头铆钉ISO105181DIN674大扁头铆钉ISO105182DIN703重型侧面带孔圆螺母83DIN705侧面带孔圆螺母GB816-8884DIN741卡头85DIN787T型槽螺钉ISO29986DIN835双头螺柱(牙长＝2D)GB900-8887DIN906内六角锥型闭锁螺钉88DIN908内六角直型闭锁螺钉89DIN909外六角锥型闭锁螺钉90DIN910外六角直型闭锁螺钉91DIN911内六角扳手ISO293692DIN912内六角圆柱头螺钉ISO4762GB70-8593DIN913内六角平端紧定螺钉ISO4026GB77-85序号德国标准中文品名国际标准中国标准94DIN914内六角尖端紧定螺钉ISO4027GB78-8595DIN915内六角圆柱端紧定螺钉ISO4028GB79-8596DIN916内六角凹端紧定螺钉ISO4029GB80-8597DIN917薄型盲螺母98DIN920开槽小圆柱头螺钉99DIN921开槽大圆柱头螺钉GB838-88100DIN923开槽圆柱头轴肩螺钉GB830-88101DIN927开槽无头轴肩螺钉102DIN928焊接方螺母GB/T13680-92 103DIN929焊接六角螺母GB/T13681-92 104DIN931六角头螺栓(半牙)ISO4014GB5782-86105DIN933六角头螺栓(全牙)ISO4017GB5783-86106DIN934六角头螺母(1型)ISO4032GB6170-86107DIN934细牙六角头螺母(1型)ISO8673GB6171-86108DIN935开槽六角螺母ISO7035GB6178-86109DIN936六角头薄螺母ISO4035GB6172.1-86 110DIN937六角头开槽薄螺母ISO7038GB6181-86111DIN938双头螺距(牙长＝1D)GB897-88112DIN939双头螺距(牙长＝1.25D)GB898-88113DIN940双头螺距(牙长＝1.5D)114DIN960六角头细牙螺栓(半牙)ISO8765GB5785-86115DIN961六角头细牙螺栓(全牙)ISO8676GB5786-86116DIN962头部穿孔六角头螺栓117DIN963开槽沉头螺钉ISO 2009GB68-85118DIN964开槽半沉头螺钉ISO 2010GB69-85119DIN965十字槽沉头螺钉ISO7046GB819-85120DIN966十字槽半沉头螺钉ISO7047GB820-85121DIN970六角头螺母122DIN971六角头螺母123DIN972细牙六角头螺母(2型)ISO8674GB6176-86124DIN975牙条(全螺纹)GB15389-94序号德国标准中文品名国际标准中国标准125DIN976螺纹销126DIN979六角头开槽薄螺母(2型)127DIN980全金属六角锁紧螺母 (1型)ISO7199GB6184-86128DIN981圆螺母ISO2982GB812-88129DIN982六角头尼龙锁紧螺母ISO7040GB889.1-86130DIN985六角头薄型尼龙锁紧螺母ISO10511GB6172.2-86 131DIN986六角盖型尼龙锁紧螺母132DIN988配合垫片133DIN1052木材连接用垫片134DIN1151沉头钢钉135DIN1440销钉专用垫片A型ISO8738136DIN1441销钉专用垫片137DIN1444带头销钉ISO2341138DIN1471圆锥型槽销ISO8744GB/T13829.2 139DIN1472圆锥型槽销(半槽)ISO8745GB/T13829.2 140DIN1473平行槽销(带倒角)ISO8740141DIN1474前端凹槽槽销ISO8741142DIN1475中部凹槽槽销ISO8742143DIN1476圆头槽销ISO8746GB/T13829.2 144DIN1477沉头槽销ISO8747145DIN1479六角螺母棒146DIN1480花篮螺栓147DIN1481弹性圆柱销ISO8752GB879-86148DIN1587组合式盖型螺母GB802-88149DIN1804开槽圆螺母(配合沟头扳手)150DIN1816圆螺母(带插销孔)151DIN2093盘型弹簧垫圈152DIN3017喉箍153DIN3404润滑油嘴(旋扭头)154DIN3567管夹155DIN3570U型螺栓序号德国标准中文品名国际标准中国标准156DIN6319球面垫圈GB849-88157DIN6325圆柱销ISO8734158DIN6330厚六角螺母GB56-88159DIN6331厚六角法兰面螺母GB6177-86160DIN6334长六角螺母161DIN6797-A外齿锁紧垫圈GB862.1-87162DIN6797-1内齿锁紧垫圈GB861.1-87163DIN6798-A外锯齿锁紧垫圈GB862.2-87164DIN6798-1内锯齿锁紧垫圈GB861.2-87165DIN6799开口挡圈GB896-76166DIN6885平键(A型)ISO773/2491167DIN6888半圆键ISO3912168DIN6899嵌环(支撑环)169DIN6900机器螺钉和垫圈组合件GB9074.1-17 170DIN6901自攻螺钉和垫圈组合件GB9074.18-23 171DIN6912薄型带孔内六角圆柱头螺钉172DIN6914大六角头螺栓173DIN6915大六角螺母174DIN6916大垫圈175DIN6917楔型方垫圈176DIN6923六角法兰面螺母ISO4161GB6177-86177DIN6925全金属六角锁紧螺母(2型)ISO7042GB6185.1-2000 178DIN7337开口型抽芯铆钉(沉头、扁圆头)GB12617/12618 179DIN7338扁平头半空心/全空心铆钉GB875/975-86 180DIN7343螺旋夹紧销ISO8750181DIN7346轻型弹性圆柱销ISO13337182DIN7349重型弹性圆柱销用垫圈183DIN7500ISO公制螺纹螺钉 (多种头型)184DIN7504自攻自钻螺钉(多种头型)185DIN7513开槽切削螺纹螺钉(多种头型)186DIN7516十字槽切削螺纹螺钉 (多种头型)序号德国标准中文品名国际标准中国标准187DIN7965T型四爪螺母188DIN7968钢结构用六角头螺栓连接副GB1228/1229/1230 189DIN7971开槽盘头自攻螺钉ISO1481GB5282-85190DIN7972开槽沉头自攻螺钉ISO1482GB5283-85191DIN7973开槽半沉头自攻螺钉ISO1483GB5284-85192DIN7976六角头自攻螺钉ISO1479GB5285-85193DIN7980圆柱头螺钉用弹簧垫圈ISO8738194DIN7981十字槽盘头自攻螺钉ISO 7049GB845-85195DIN7982十字槽沉头自攻螺钉ISO7050GB846-85196DIN7983十字槽半沉头自攻螺钉ISO7051GB847-86197DIN7984薄型内六角圆柱头螺钉198DIN7985十字槽盘头螺钉ISO7045GB818-85199DIN7989钢结构用垫圈GB1230-84200DIN7990钢结构用六角头螺栓GB1229-84201DIN7991内六角沉头螺钉ISO10642202DIN7993轴用钢丝挡圈GB895.2-86203DIN7995十字槽半沉头木螺钉GB952-86204DIN7996十字槽圆头木螺钉GB950-86205DIN7997十字槽沉头木螺钉GB951-86206DIN8140螺纹护套(普通\自锁等)207DIN9021大外径垫圈ISO7093GB96-85208DIN11024弹簧卡子209DIN13257平板螺栓210DIN18182干壁钉(墙板钉)211DIN28129环型螺母GB63-88212DIN70952圆螺母用止退垫圈GB858-88。

∙销及键∙•弹性圆柱销—开槽—轻型 Spring-type straightpins,slotted,light duty∙DIN EN ISO 13337 | 代替DIN 7346∙•重型传动连接楔形键—斜键和键槽型式及尺寸 Stressed-type fastenings with taper action-Taper keys keyways-Dimensions and application∙DIN 6886∙•半圆键和键槽型式及尺寸 Drive-type fastenings without taper action-Woodruff keys-Dimensions and application∙DIN 6888∙•弹性圆柱销—开槽—重型 Spring-type straightpins,slotted,heavy duty∙DIN EN ISO 8752 | 代替DIN 1481∙•机床用平键—传动连接—键和键槽型式及尺寸 Drive-type fastenings without taper action-Parallel keys,keyways,deeppattern for machine tools-Dimensions and application∙DIN 6885-2∙•薄型平键—传动连接—键和键槽型式及尺寸 Drive-type fastenings without taper action-Parallel keys,shallowaction-Dimensions and application∙DIN 6885-3∙•弹性开口销 Spring cotters∙DIN 11024∙•开口销 Split pins∙DIN EN ISO 1234 | 代替DIN 94∙•腰型头轴肩销轴 Clevis pins with head and stud end∙DIN 1445∙•圆柱销 Clevis pins without head∙DIN EN 22340 | 代替DIN 1443∙•销轴 Clevis pins with head∙DIN EN 22341 | 代替DIN 1444∙•弯头楔键和键槽型式及尺寸 Taper key torquetransmission-Gib-head saddle keys-Dimensions and application∙DIN 6889∙•交变载荷用楔键和楔键槽 Tangential keys and tangential keyways for alternating shock loads∙DIN 268∙•单一载荷用楔键和楔键槽 Tangential keys and tangential keyways for constant loads∙DIN 271∙•平键用钢一型式、尺寸、重量及允许偏差 Bright key steel-Dimensions,permissible variations,weights∙DIN 6880∙•鞍形楔键—扭矩传输—尺寸及安装连接要求 Taper key torque transmission-Saddle keys-Dimensions and application∙DIN 6881∙•楔键—扭矩传输—尺寸及安装连接要求 Taper key torque transmission-Parallel keys-Dimensions and application∙DIN 6883∙•弯头楔键—扭矩传输—尺寸及安装连接要求 Taper key torque transmission-Gib-head parallel keys-Dimensions and application∙DIN 6884∙•平键—传动连接—键和键槽型式及尺寸 Drive-type fastenings without taper action-Parallel keys,keyways,deep pattern∙DIN 6885-1∙•外螺纹圆锥销 Taper pins with thread ends and constant taper lengths∙DIN 258∙•槽销 Grooved pins,half - length grooved,with gorge∙DIN 1469∙•固定销 Rivet pins∙DIN 7341∙•圆锥销—内螺纹 Unhardened taper pins∙DIN EN 22339 | 代替DIN 1∙•内螺纹圆锥销—不淬硬 Unhardened taper pins with internal thread∙DIN EN 28736 | 代替DIN 7978∙•外螺纹圆锥销—不淬硬 Unhardened taper pins with external thread∙DIN EN 28737 | 代替DIN 7977∙•圆柱销—不淬硬钢和奥氏体不锈钢 Parallel pins,of unhardened steel and austenitic stainless steel∙DIN EN ISO 2338 | 代替DIN 7∙•内螺纹圆柱销—不淬硬钢和奥氏体不锈钢 Parallel pins whit internal thread,of unhardened steel and austenitic stainless steel∙DIN EN ISO 8733 | 代替DIN 7979∙•圆柱销－淬硬钢和马氏体不锈钢（定位销） Parallel pins,of hardened steel or martensitic stainless steel(Dowel pins)∙DIN EN ISO 8734 | 代替DIN 6325∙•内螺纹圆柱销－淬硬钢和马氏体不锈钢 Parallel pins with internal thread,of hardened steel and martensitic stainless steel∙DIN EN ISO 8735 | 代替DIN 7979∙•槽销—带导杆及全长平行沟槽 Grooved pins,full - length parallel grooved,with pilot∙DIN EN ISO 8739 | 代替DIN 1470∙•槽销—带倒角及全长平行沟槽 Grooved pins,full - length parallel grooved,with chamfer∙DIN EN ISO 8740 | 代替DIN 1473∙•槽销—半长倒锥槽 Grooved pins,half - length reverse - taper grooved∙DIN EN ISO 8741 | 代替DIN 1474∙•槽销—中部槽长为1/3全长 Grooved pins,one - third -length centre grooved∙DIN EN ISO 8742 | 代替DIN 1475∙•槽销—中部槽长为1/2全长 Grooved pins,half-length centre grooved∙DIN EN ISO 8743∙•槽销—全长锥槽 Grooved pins,full-length taper grooved∙DIN EN ISO 8744 | 代替DIN 1471∙•槽销—半长锥槽 Grooved pins,half-length taper grooved∙DIN EN ISO 8745 | 代替DIN 1472∙•圆头槽销 Grooved pins with round head∙DIN EN ISO 8746 | 代替DIN 1476∙•沉头槽销 Grooved pins with countersunk head∙DIN EN ISO 8747 | 代替DIN 1477∙•弹性圆柱销—卷制—重型 Spring-type straightpins,coiled,heavy duty∙DIN EN ISO 8748 | 代替DIN 7344∙•弹性圆柱销—卷制—标准型 Spring-type straight pins,coiled,standard duty∙DIN EN ISO 8750 | 代替DIN 7343∙•弹性圆柱销卷制轻型 Spring-type straight pins,coiled,light duty∙DIN EN ISO 8751∙•重型传动连接楔形键—弯头斜键和键槽型式及尺寸 Stressed-type fastenings with taper action-Taper keys with gibheads,keyways-Dimensions and application∙DIN 6887∙本文版权所属标准件之都网，如需转载、摘编或以其它方式使用本文内容，请在授权范围内使用，并标注“来源：标准件之都”。