_NBR 14136-2002

NovaSeq6000定序系統現場準備指南簡介3運送與安裝4實驗室要求5試劑組的儲存要求7 PCR流程實驗室設定7電氣要求8不斷電電源供應器11環境注意事項11網路和電腦安全性13主機網路注意事項14資料輸出和儲存17使用者提供的耗材和設備18修訂記錄20技術協助22文件#1000000019360v06CHTILLUMINA所屬財產2019年1月此文件與其內容為Illumina,Inc.與其分支機構(「Illumina」)之專有財產，僅供客戶針對本文件所述之產品用途於契約規範內使用，不得移作他用。

此文件與其內容不得基於其他用途而使用或散播，和/或在未事先取得Illumina的書面同意下，以任何方式流通、揭露或複製。

Illumina並未藉由本文件傳遞其專利、商標、版權或任何普通法權利或任何第三方之類似權利的任何授權。

本文件的指示必須由受過適當訓練的合格人員嚴格且明確地遵守，以確保此處所述之產品的適當與安全使用。

在使用該產品之前，必須完整閱讀與了解文件的所有內容。

若未全文閱讀並明確遵守此處的所有指示，可能造成產品損壞、人員受傷(包括使用者或其他人)，以及其他財產損壞，並導致產品保固失效。

對於不當使用本文所述產品(包括其零件或軟體)而造成的損失，Illumina不承擔任何責任。

©2019Illumina,Inc.保留一切權利。

所有商標均為Illumina,Inc.或其各自所有權人所擁有。

如需特定商標資訊，請參閱/company/legal.html。

簡介本指南提供各種規格與準則，協助您準備Illumina®NovaSeq™6000定序系統的安裝場地，並瞭解各項操作。

u實驗室空間要求u電氣要求u環境限制u運算要求u使用者提供的耗材和設備安全注意事項有關安全注意事項的重要資訊，請參閱「NovaSeq6000定序系統安全及合規指南」(文件編號1000000019357)。

額外的資源Illumina網站的NovaSeq6000定序系統支援頁面可提供額外系統資源。

NOVEMBER 2002NBR 14136ABNT - Brazilian Association ofT echnical Standards Plugs and socket-outlets for household and similar purposes up to20 A/250 Va.c. - StandardizationOrigin: Project NBR 14136:2001CE-03:023.02 - Study Commission for Switches, Socket-outlets, Pins and Plates for General UseNBR 14136 - Plugs and socket-outlets for household and similar purposes StandardizationDescriptors: Plug. Socket-outletThis Standard has been based on IEC 60906-1:1986This Standard cancels and replaces NBR 14136:1998Valid from December 29, 2002 onKey-words: Plug. Socket-outlet20 pagesSummaryForeword1Objective2Normative references3RequirementsANNEXA FiguresForewordABNT – The Brazilian Association of Technical Standards - is the National Committee of Standardization. The Brazilian standards, which content is responsibility of Brazilian Committees (ABNT/CB) and the Organizations of Sectorial Standardization (ABNT/ONS), are elaborated by Study Commissions (CE), composed by representatives of the involved sections, like: producers, consumers and neutral (universities, laboratories and other).The drafts of Brazilian standards, elaborated in the extent of ABNT/CB and ABNT/ONS, are circulated for Public Consultation among ABNT associates and interested parties.This Standard contains the annex A, it is normative.1Scope1.1This Standard sets the dimensions for plugs and socket-outlets with nominalcharacteristics up to 20 A/250 V a.c., intended for household and similar purposes, to be used in the connection to distribution systems with nominal tensions rated between 100 V and 250 V a.c.1.2This Standard is applied to the plugs and socket-outlets specified in NBR 6147.1.3This Standard is not applied to the plugs and socket-outlets designed to theclass 0 equipments.2Normative referencesThe following normative documents contain provisions which, through reference in this text, constitute provisions of this Standard. The indicated issues were in force when this Standard was published. As every Standard might suffer revisions, it is recommended to those that accomplish agreements based on this document to verify the convenience of using the most recent issue of the mentioned Standards. ABNT maintains registers of currently valid editions.NBR 6147:2000 - Plugs and socket-outlets for household and similar purposes - SpecificationNBR 11467:1991 - graphic Symbols for use in equipments - Symbols2 NBR14136:20023Requirements3.1DimensionsThe plugs and socket-outlets shall be in agreement with the dimensions of theappropriate figures of annex A.3.2CompatibilityThe 20A socket-outlets shall admit the insertion of 10 A and 20 A plugs, and the socket-outlets with earthing-contact shall admit the insertion of plugs with and without earthing-pin.The 10 A socket-outlets shall not admit the insertion of 20 A plugs./ ANNEX ANBR14136:2002 3Annex A (normative)FiguresDimensions in millimetersSharp edgesslightly roundedDetail of theentrance holesProtecting surfaceNOTES1See explanatory notes on page 9.2These figures are not intended to govern the plan, except in the shown dimensions.3Several constructions can be used, such as multiple socket-outlets.Figure 1 – Socket-outlet to built-in, two-pole, with earthing contact - 10 A/250 V c.a.4 NBR14136:2002Dimensions in millimetersSharp edgesslightly roundedDetail of theentrance holesProtecting surface NOTES1See explanatory notes on page 9.2These figures are not intended to govern the plan, except in the shown dimensions.3 Several constructions can be used, such as multiple socket-outlets.Figure 2 – Socket-outlet to built-in, two-pole, with earthing contact - 20 A/250 Vc.a.NBR14136:2002 5Dimensions in millimetersProtecting surfaceWith protecting surface Without protecting surfaceNOTES1See explanatory notes on page 9.2For the dimensions that were not indicated see figure 1.3These figures are not intended to govern the plan, except in the shown dimensions.4Several constructions can be used, such as multiple socket-outlets.Figure 3 - Socket-outlet to semi-built-in or to put upon, two-pole, with earthing-contact - 10 A/250 Vc.a.6 NBR14136:2002Dimensions in millimetersProtecting surfaceWith protecting surface Without protecting surfaceNOTES1See explanatory notes on page 9.2For the dimensions that were not indicated see figure 2.3 These figures are not intended to govern the plan, except in the shown dimensions.4 Several constructions can be used, such as multiple socket-outlets.Figure 4 – Socket-outlet to semi-built-in or to put upon, two-pole, with earthing-contact - 20 A/250 Vc.a.NBR14136:2002 7Dimensions in millimeters With recess With collarProtecting surfaceWith protecting surface Without protecting surfaceNOTES1See explanatory notes on page 9.2For the dimensions that were not indicated see figure 1.3These figures are not intended to govern the plan, except in the shown dimensions.4Several constructions can be used, such as multiple socket-outlets.Figure 5 – Portable socket-outlet, two-pole, with earthing contact. - 10 A/250 Vc.a.8 NBR14136:2002Dimensions in millimeters With recess With collarProtecting surfaceWith protecting surface Without protecting surfaceNOTES1See explanatory notes on page 9.2For the dimensions that were not indicated see figure 2.3These figures are not intended to govern the plan, except in the shown dimensions.4Several constructions can be used, such as multiple socket-outlets.Figure 6 – Portable socket-outlet, two-pole, with earthing contact. - 20 A/250 Vc.a.NBR14136:2002 9 Explanatory notes for figures 1, 2, 3, 4, 5 and 6Î A recess shall be provided for socket-outlets to built-in, a collar for those to put upon or for portable types, or a combination of both for the semi-built-in type.For the semi-built-in socket-outlets, the impossibility of single-pole insertion shall be verified.ÏIf those dimensions were not respected, a gauge shall be used for verifying theimpossibility of single-pole insertion.Regarding the use of shutters as the only way to prevent single-pole insertion, see NBR 6147.ÐThis dimension has been provided for the plate, the guide of the plug pins and for the eventual shutter mechanism. The shutters are optional.It is not necessary to supply a proper space to the shutters in those models without this device.ÑIn the limits of that thickness, the guide for the plug pins shall have at least 1,5 mm with the specified diameter.ÒSmall chamfer or radius.ÓThe points that first touch the alive contacts and the earthing-contact shall be verified.ÔThis dimension is verified using a gauge in the most unfavorable conditions.ÕThe contacts shall be elastic. Their shape might be different from the tubular.An entrance in an appropriate way, with a chamfer or a radius, is necessary to prevent damage of the contact when the plug is inserted in the most unfavorable angle.Its convenience is verified by performing all the tests specified in NBR 6147.ÖThe earthing-terminal shall be identified with the symbol (3.2.19 of NBR 11467:1991).The identification of the other terminals is optional.The marking shall be put close to the terminals.It is not necessary to mark the terminals in those models that cannot by disassembled.10 NBR14136:2002Dimensions in millimetersEngagement faceNo sharp edgesEarthing-pin and optional constructionfor the pin that carries current (alive) NOTES1See explanatory notes on page 12.2These figures are not intended to govern the plan, except in the shown dimensions.3The plugs can, or cannot, be disassembled.Figure 7 – Two-pole Plug, with earthing-pin (for class I appliances) up to 10 A/250 Vc.a.Dimensions in millimetersNOTES1See explanatory notes on page 12.2These figures are not intended to govern the plan, except in the shown dimensions.3The plugs can, or cannot, be disassembled.Figure 8 – Two-pole Plug, with earthing-pin (for class I appliances) above 10 A up to 20 A/250 Vc.a.Engagement faceEarthing-pin and optional construction for the pin that carries current (alive)No sharp edgesExplanatory notes for figures 7 and 8ÎThe earthing-terminal shall be identified with the symbol (3.2.19 of NBR 11467:1991).The identification of the other terminals is optional.The marking shall be made inside the body, close to the terminals.It is not necessary to mark the terminals in those models that cannot be disassembled.ÏThe distance between the engagement face and the cord or the exit for the cable or the eventual cord protection shall be of 14 mm, at least.The conformity is verified by measurement.ÐIn the limits of this dimension, the outline shall not be smaller than the outline of the engagement face.ÑIn the limits of this dimension, the outline should not be larger than outline of the engagement face.ÒThe insulating sleeves of the alive pins are optional.If the insulating sleeves are separated parts, they shall penetrate in the body of the plug in, at least, 3 mm measured from the engagement face.ÓThe external diameter of the insulating sleeves shall not overcome the uncovered part of the pins.ÔTo avoid the shutters damage, the extremities of the pins shall not present sharp edges or burrs; they shall be rounded, as shown.ÕThe angle of 90º sets the maximum area which the flexible cord entrance shall be allowed.Dimensions in millimetersDetail of theentrance holesNOTES1See explanatory notes on page 17.2The socket-outlets can, or cannot, be disassembled.3These figures are not intended to govern the plan, except in the shown dimensions.4Several constructions can be used, such as multiple socket-outlets.Figure 9 – Portable two-pole socket-outlet without earthing-contact - 10 A/250 Vc.a.Dimensions in millimetersDetail of the entranceholesNOTES1See explanatory notes on page 17.2The socket-outlets can, or cannot, be disassembled.3These figures are not intended to govern the plan, except in the shown dimensions.4Several constructions can be used, such as multiple socket-outlets.Figure 10 - Portable two-pole socket-outlet without earthing-contact - 20 A/250 Vc.a.Dimensions in millimeters With recess With collarProtecting surfaceNOTES1See explanatory notes on page 17.2The socket-outlets can, or cannot, be disassembled.3These figures are not intended to govern the plan, except in the shown dimensions.4Several constructions can be used, such as multiple socket-outlets.Figure 11 - Portable two-pole socket-outlet without earthing-contact with protecting surface - 10 A/250 Vc.a.Dimensions in millimetersWith recess With collarProtecting surfaceNOTES1See explanatory notes on page 17.2For the dimensions that were not indicated, see Figure 10.3These figures are not intended to govern the plan, except in the shown dimensions.4Several constructions can be used, such as multiple socket-outlets.Figure 12 - Portable two-pole socket-outlet without earthing-contact with protecting surface - 20 A/250 Vc.a.Explanatory notes for figures 9, 10, 11 and 12.These Figures are equally provided for socket-outlets which are incorporated in appliances.Î A collar shall be provided for the models without protecting surface or a recess, or a combination of a collar and a recess for the socket-outlets with protecting surface.In cases of such combination the impossibility of single-pole insertion shall be verified.ÏIf those dimensions were not respected, a gauge shall be used for verifying the impossibility of single-pole insertion. Regarding the use of shutters as the only way to prevent single-pole insertion, see NBR 6147.ÐThis dimension has been provided for the plate, the guide of the plug pins and for the eventual shutter mechanism. These shutters are optional.It is not necessary to supply a proper space to the shutters in those models without this device.ÑIn the limits of that thickness, the guide for the plug pins shall have at least 1,5 mm with the specified diameter.ÒSmall chamfer or radius.ÓThe points that first contact shall be verified with a gauge.ÔThe contacts shall be elastic. Their shape might be different from the tubular.An entrance in an appropriate way, with a chamfer or a radius, is necessary to prevent the damage of the contact when the plug is inserted in the most unfavorable angle. Its convenience is verified by performing all the tests specified in NBR 6147.Dimensions in millimetersEngagement faceOptional construction withoutinsulating sleevesNOTES1See explanatory notes on page 20.2These figures are not intended to govern the plan, except in the shown dimensions.3This plug can, or cannot, be disassembled.Figure 13 - Two-pole Plug without earthing-pin (for class II appliances) up to 10 A/250 V a.c.Dimensions in millimetersEngagement faceOptional construction withoutinsulating sleevesNOTES1See explanatory notes on page 20.2These figures are not intended to govern the plan, except in the shown dimensions.3This plug can, or cannot, be disassembled.Figure 14 - Two-pole Plug without earthing-pin (for class II appliances) above 10 A up to 20 A/250 Vc.a.Explanatory notes for figures 13 and 14ÎThe distance between the engagement face and the cord or the exit for the cord or the eventual protection of the cord shall be 14 mm, at least.The conformity is verified by measurement.ÏIn the limits of this dimension, the outline shall not be smaller than the outline of the engagement face.ÐIn the limits of that dimension, the outline shall not be larger than the outline of the engagement face.ÑThe insulating sleeves of the alive pins are optional.If the insulating sleeves are separated parts, they shall penetrate in the body of the plug in, at least, 3 mm measured from the engagement face.ÒThe external diameter of the insulating sleeves shall not overcome the uncovered part of the pins.ÓTo avoid the shutters damage, the extremities of the pins shall not present sharp edges or burrs; they shall be rounded, as shown.ÔThe angle of 90º sets the maximum area which the flexible cord entrance shall be allowed.。

失禁者用尿液吸收剂聚丙烯酸酯高吸水性粉末第5部分：在盐溶液中用称重法测定吸水率警示—本文件并不要求解决与其使用相关的任何安全问题。

本文件的使用者有责任在使用前进行适当的安全和健康练习，并确定监管限制的适用性。

执行试验的人员应接受过本程序各方面的充分培训。

1范围本文件描述了一种测定聚丙烯酸酯高吸水性粉末在盐溶液中吸水率的试验方法。

2规范性引用文件下列文件中的内容通过文中的规范性引用而构成本文件必不可少的条款。

其中，注日期的引用文件，仅该日期对应的版本适用于本文件。

不注日期的引用文件，其最新版本（包括所有的修改单）适用于本文件。

ISO187纸、纸板和纸浆试样处理和试验的标准大气条件（Paper,board and pulps—Standard atmosphere for conditioning and testing and procedure for monitoring the atmosphere and conditioning of samples）ISO3696分析实验室用水规格和试验方法（Water for analytical laboratory use—Specification and test methods）3术语和定义下列术语和定义适用于本文件。

3.1样品sample从同一生产批次中提取的用于检测目的、可识别且可追溯其原产地的产品或产品的一部分。

3.2样本specimen识别样品（3.1）中用于测试的部分。

4总则样品称重后放入一个透水袋中。

将袋浸入待吸收的液体中，按规定时间浸泡，之后将袋子取出。

允许多余的液体滴落，通过样品称重来确定液体的吸收量。

15试剂和材料只能使用公认分析级别的试剂，另有规定的除外。

5.1水符合ISO3696的3级水，但电导率能达到30μS/cm。

5.2氯化钠溶液5.2.1氯化钠水溶液的质量分数为0.9%。

称取(9.00±0.01)g氯化钠到1L烧杯中，加入(991.0±0.1)g 去离子水(3级)，搅拌直至溶解。

目录1、VDE欧规胶壳插脚：标准-EN50075/IEC600832、BS英规胶壳插脚：标准-BS13633、SAA澳规胶壳插脚：标准-AS/NZS31124、UL美规胶壳插脚：标准-ANSI-NEMA WD65、CCC中国规胶壳插脚：标准-GB1002-20086、Korea韩国胶壳插脚：标准-KSC83057、Brasil巴西规胶壳插脚：NBR141368、India印度胶壳插脚：标准IS12939、Argentina阿根廷胶壳插脚：IRAM206310、SASO沙特胶壳插脚：SASO-220311、JAPAN日本胶壳插脚：JISC830312、小南非规胶壳插脚：SABS164-1修订记录2013-10-15修改：1、GB1002-2008版CCC插脚（厚1.4-1.5mm）增加插头插销离边沿的距离不小于6.5mm。

2、增加日规插脚安规尺寸图表，日规插脚（厚1.4-1.6mm）备注“L"的尺寸要求不大于0.9mm，及插头插销离边沿的距离不小于5.1mm。

3、修改美规插脚安规尺寸，美规插脚（厚1.40-1.65mm），备注插头插销离边沿的距离不小于5.1mm.。

4、插脚图示缩小2PIN欧洲插脚Two-pin plugs f(Up to2.5A rating)EN50075/IEC60083-C5/CEE7/DIN49464P≥4.0,Q≥18.0,I：金属下部结合部分边缘应光滑钝化,不得尖锐刺手.此插脚适应国家包括:德国,俄罗斯,以色列英国插脚UK Plug Checking Form according to Figure 4of BS1363BS-3Symbol Requirement(mm)Symbol Requirement (mm)Symbol Requirement(mm)Symbol Requirement(mm)A 25.37max.I 22.10-22.36Q 17.2-18.2Y 1.2-2.0B25.37max.J 22.23-23.23R 6.22-6.48Z R 0.1-1.0C34.6max.K 1.35-1.85S 3.90-4.05a 58︒-62︒D11.05-11.18L 7.80-8.05T 6.22-6.48b 1.35-1.85E11.05-11.18M 58︒-62︒U 6.35min.c 58︒-62︒FR 15min.N 3.90-4.05V 60︒-80︒d 1.35-1.85GR 9.5min.O 9.2max.W 1.35-1.85e 0.2max.H R 9.5min.P 9.5max.X 3.90-4.05f 1.35-1.85此插脚适应国家包括:英国、新加坡、马来西亚Grounding pin澳规插脚AS/NZS3112Standard sheet Figure 2.1(a1)or 2.1(c)Standard sheet Figure 2.1(e)and fig 2.4PositionRequired (mm)By Measurement (mm)By the gauges in Figure A1A6.35±0.15-B6.35±0.15C+0.150.051.63--D7.92--E10.31--F17.06±0.4-G19.94±0.81、2、3、421.9max.or 27.0min.-5、660︒--78.6min.-821.0max.-920.0±1.0-101.0max -118.7±0.5-Distance fromprojection part edge toL and N pins 9mm min.美国插脚UL插脚：According toUL1310/UL498/UL817/UL1659/ANSI-NEMA WD6-2002Figure1-15备注：关于电源插墙式插脚（UL1310)中7.16条款要求：起始于金属插脚的任意一点，与金属插脚的托台圆周边之间的距离不得小于5.1mm。

Portaria n.º 271, de 21 de junho de 2011O PRESIDENTE DO INSTITUTO NACIONAL DE METROLOGIA, NORMALIZAÇÃO E QUALIDADE INDUSTRIAL - INMETRO, em exercício, no uso de suas atribuições, conferidas no § 3º do artigo 4º da Lei n.º 5.966, de 11 de dezembro de 1973, no inciso I do artigo 3º da Lei n.º 9.933, de 20 de dezembro de 1999, e no inciso V do artigo 18 da Estrutura Regimental da Autarquia, aprovada pelo Decreto n° 6.275, de 28 de novembro de 2007;Considerando a alínea f do subitem 4.2 do Termo de Referência do Sistema Brasileiro de Avaliação da Conformidade, aprovado pela Resolução Conmetro nº 04, de 02 de dezembro de 2002, que atribui ao Inmetro a competência para estabelecer as diretrizes e critérios para a atividade de avaliação da conformidade;Considerando o artigo 1º da Resolução Conmetro n.º 11, de 20 de dezembro de 2006, que determina o atendimento, pelas empresas fabricantes e importadoras de plugues e tomadas, às especificações da norma ABNT NBR 14136 e configura observância ao estabelecido nesta Resolução e em Portaria do Inmetro, tornando compulsória a certificação de plugues e tomadas;Considerando a Portaria Inmetro nº 85, de 03 de abril de 2006, que aprova, para observância compulsória, o Regulamento de Avaliação da Conformidade para Plugues e Tomadas para uso Doméstico e Análogo e dá outras providências;Considerando a Portaria Inmetro nº 324, de 21 de agosto de 2007, que aprova o Regulamento de Avaliação da Conformidade para Adaptadores de Plugues e Tomadas;Considerando a Portaria Inmetro nº 251, de 15 de setembro de 2009, que estabelece os projetos básicos para as possíveis configurações de adaptadores reversos de plugues e tomadas;Considerando a necessidade de adoção de novas medidas que visem a esclarecer aspectos construtivos obrigatórios para o padrão de plugues e tomadas, conforme ABNT NBR 14136, resolve:Art. 1º Determinar que as tomadas fixas ou móveis de 3 (três) contatos, desmontáveis ou não desmontáveis, deverão ter marcados nos bornes neutro e terra os símbolos correspondentes, respectivamente N e .Art. 2° Estabelecer que os adaptadores e as tomadas fixas ou móveis de 2 (dois) ou 3 (três) contatos, desmontáveis ou não desmontáveis, comercializados em todo o território nacional, deverão ser construídos de forma a não permitir a desconfiguração ou a descaracterização do padrão conforme a norma ABNT NBR 14136, inclusive nos casos em que seja necessário o uso de ferramentas para este fim.Parágrafo Único – A determinação constante no caput deverá ser estendida para os conjuntos constituídos por plugue, tomada múltipla e cordão prolongador (comumente denominado extensão).Art. 3° Estabelecer que os adaptadores e as tomadas fixas ou móveis de 2 (dois) ou 3 (três) contatos, desmontáveis ou não desmontáveis, comercializados em todo o território nacional, não deverão apresentar qualquer dispositivo que anule a funcionalidade do pino de aterramento.Parágrafo Único –A determinação constante no caput deverá ser estendida para cordões conectores e para os conjuntos constituídos por plugue, tomada múltipla e cordão prolongador (comumente denominado extensão).Art. 4° Os plugues de dois ou três pinos, as tomadas fixas ou móveis e os adaptadores deverão ter estampadas em seu corpo as seguintes indicações:a) o nome, a marca ou o logotipo do fabricante;b) a tensão a que se destinam em Volt (V);c) a potência em Watt (W) ou a corrente nominal em Ampère (A);d) país de fabricação; e oe) selo de identificação da conformidade.Art. 5° Estabelecer que a partir de 12 (doze) meses após a publicação desta Portaria, a fabricação e a importação das tomadas fixas ou móveis de 2 (dois) ou 3 (três) contatos, desmontáveis ou não desmontáveis, deverão atender aos requisitos estabelecidos nos artigos 1º e 2º desta Portaria.Parágrafo Único –Dezoito meses após a publicação desta Portaria, os produtos mencionados no caput somente deverão ser comercializados, por fabricantes e importadores, em conformidade com os requisitos estabelecidos nos artigos 1º e 2º desta Portaria.Art. 6º Estabelecer que a partir de 24 (vinte e quatro) meses após a publicação desta Portaria, os produtos mencionados no artigo anterior somente deverão ser comercializados, por atacadistas e varejistas, em conformidade com os requisitos estabelecidos nos artigos 1º e 2º desta Portaria.Parágrafo Único - A determinação contida no caput não é aplicável aos fabricantes e importadores, que deverão observar os prazos fixados no artigo anterior.Art. 7º Determinar que para as tomadas fixas ou móveis de 2 (dois) ou 3 (três) contatos, desmontáveis ou não desmontáveis, os demais artigos desta Portaria serão de cumprimento obrigatório a partir da data de sua publicação.Art. 8º Estabelecer que para os adaptadores de plugues e tomadas, os artigos pertinentes expressos nesta Portaria serão de cumprimento obrigatório a partir da data de sua publicação.Art. 9º Determinar que, para fins de certificação, quando da aplicação da Portaria Inmetro nº 85, de 03 de abril de 2006, da Portaria Inmetro nº 324, de 21 de agosto de 2007, e da Portaria Inmetro nº 251, de 15 de setembro de 2009, serão atendidos os artigos 1º, 2º, 3º e 4º desta Portaria.Art. 10 Cientificar que a fiscalização do cumprimento das disposições contidas nesta Portaria, em todo o território nacional, ficará a cargo do Inmetro e das entidades de direito público a ele vinculadas por convênio de delegação.Parágrafo Único – A fiscalização observará os prazos estabelecidos nos artigos 5º, 6º, 7º e 8º desta Portaria.Art. 11 Esta Portaria entrará em vigor na data de sua publicação no Diário Oficial da União.JOÃO ALZIRO HERZ DA JORNADA。

欧标2.5A意大利标瑞士标英标欧标/德标欧标/德标 插头详细信息1932Φ36.510Φ4.81954欧标/德标插头电气参数：电流：16A 电压：250V 频率：50Hz 简 介：欧标插头（两圆）的制造标准按CE 标准执行。

欧标插头在德国、奥地利、荷兰、瑞典、挪威、芬兰、俄罗斯等大部分欧洲国家使用，由于这个标准在整个欧洲普遍使用，我们把它称为是“欧洲大陆”的标准。

插头是两个圆柱，跨距为19mm,接地级是通过两侧插头接地完成的。

中欧和东欧7 / 7欧式插头有嵌入式插脚，法国和比利时插座与之相似。

在欧洲标准插座电气参数是10A-16A 230ACV 交流电源。

欧标插座是世界上最安全的插座，接地最特殊主要是考虑人得安全。

因此也是世界上使用最广泛的插头标准。

注：意大利标插头是三圆柱一条线，丹麦标和瑞士标插头是三圆柱成三角形状，都是有直接接地级插脚。

瑞典国医疗用途的插头要注塑一体禁止接线插头使用。

俄罗斯认证机构GOST 规格要求中欧和东欧7 / 7插头是16A 的标准。

英标 插头详细信息6.34822.522.5182321.7525045英标英标插头、插座电气参数：电流： 13A 电压：250V 频率：50Hz 简 介：英式标准插头（品字形插头）说明:英式标准插头（品字形插头）按BS 1363 制造标准执行，也叫英标。

自1962年至今英国官方插头标准一直沿用BS 1363。

英标也用在爱尔兰、、马来西亚和新加坡等英属殖民地国家。

英国标准的插头是品字形、矩形柱状，截面大、耐受大电流，是众多插头标准里最安全的插头之一。

英标电源插座有保护门设计，可以防止异物插入或者防止误插入，更加安全可靠。

插头插座是强制接受英国ASTA 测试认证机构的认证和电器测试。

英标插头的电气参数是 3-13A/250VAC*******************************************************************************欧标（2.5A ） 插头详细信息欧标（2.5A ）插头电气参数：电流：2.5A 电压：250V 频率：50Hz简介：欧式插头（无接地）说明:欧式插头（无接地）制造标准按CEE 7/16 标准执行。