TOTA矩阵主机说明书

A tlonA4 x 4 HDMI V1.3 Matrix SwitcherAT-HD-V44M1. Introduction (1)2. Application (1)3. Package Contents (1)4. System Requirement (1)5. Features (2)6. Installation (3)7. Front View (4)8. Remote Control (5)9. RS-232 Protocol (5)9.1 Commands (6)10. Connection and Installation (7)11. Specifications (8)12. Safety Information (9)13. Warranty (10)Thank you for purchasing Atlona’s 4 x 4 HDMI V1.3 Matrix Switcher. While HDMI products are getting more and more popular in the market people usually have more than one HDMI de-vices and sources in one place. The AT-HD-V44M provides the excellent solution for connecting all the devices and sources together for your convenience use, it also provides you a variety of choices of where to play your images with remote controller. Further, the AT-HD-V44M can transfer Deep Color video and bit stream digital audio with maximum performance and it sup-ports HDMI 1.3, HDCP 1.1 and DVI 1.0.Please follow this manual to begin enjoying the benefit of your Atlona HDMI 1.3 Matrix Switch-er. We suggest keeping it in a safe place for future reference.• High performance Atlona HDMI 1.3 Matrix Switcher with 4 (four) input and 4 (four) output with remote control for you to link with your favor HDMI devices to enjoy movies, music, or games at once.• Each of the four HDMI sources can be directed to any two of HDMI displays and or to all of the HDMI display.• When HDMI signal progresses through the system, it is re-timed, and level-compensated.• Define HDCP, HDMI and DVI source. The LED light will light up to define the input source’s format.• Switchable EDID function for choosing the native resolution to display.• 4 by 4 V1.3 HDMI Matrix Unit. (AT-HD-V44M)• Remote Control (with Battery)• IR Receiver• Power Cord• 5V DC power supply adaptor.• Operation Manual.HDMI input device(s) and HDMI output device(s).• HDMI 1.3, HDCP 1.1 and DVI 1.0 compliant.• Supports digital video formats in Deep Color 12bit and new lossless compressed (Dolby True-HD, Dolby Digital Plus and DTS-HD Master Audio) digital audio.• The HDMI input is compensated, clock / phase adjusted, and jitter eliminated so the output is a brand new standard HDMI signal.• Supports input source LED indicators on each output select.• Compatible with all HDMI sources and displays.• Supports a wide range of PC and HDTV resolutions from VGA to UXGA and 480i to 1080p.• Supports RS-232 control.• Supports IR remote control and IR extender.• Dolby Digital, DTS digital audio transmission (32-192 kHz Fs sample rate).• Supports LPCM7.1 channels output from each independent HDMI ports.• HDMI cable distance test with 1080p/8bit resolution, the Input/Output source can run up to 15/15 meters. If 1080p/12bit the Input/Output source can run up to 15/6 meters.1 EDID Control Switcher: Default factory setting is TV, leave as it is when the displays are working properly. Switch to STD to use build-in EDID Detail capability in Note.2 RS-232 communication port: Connect the COM port of your PC for the distant control over RS-232 channel. Detail specification in section 9.3 HDMI outputs: Connect each of these output ports to the HDMI display(s).4 HDMI inputs: Connect input ports to the HDMI or DVI output of your source equipment such as DVD player or set-top-box.5 Power: Plug the 5VDC power supply into the unit and connect the adaptor to AC wall outlet.6 IR extender.Note:1. EDID Control Switch: STD(INT) and TV(EXT), Default setting is TV2. When EDID is on TV: Leave as it is if display is properly, unit will detect the first HDMI output source’s EDID and record in the unit. If the first detected output source is DVI it will pass to next source, until the first HDMI been detected. The detection priority is HDMI v1.3 > HDMI v1.2 > DVI.3. When EDID is on STD: unit use build-in EDID Video Support->1080p 12bit(max) Audio Sup -port->PCM24. Your EDID selection will only activate when the unit is replugged and powered on.1345621 Remote control sensor.2 Power switch & LED Indicator: The LED will illuminate when the power is turned on.3 Input Select/Indicators (A): Press the HDMI out “A” button repeatedly to switch to your desired source and the LED will illuminate to indicate which input source is being selected and routed to HDMI A output. When an HDMI or DVI source is connected the LED light labeled “HDMI/DVI” will activate. If the source is HDCP encrypted, the LED light labeled “HDCP” will acti -vate.4 Input Select/Indicators (B): Press the HDMI out “B” button repeatedly to switch to your desired source and the LED will illuminate to indicate which input source is being selected and routed to HDMI B output. When an HDMI or DVI source is connected the LED light labeled “HDMI/DVI” will activate. If the source is HDCP encrypted, the LED light labeled “HDCP” will acti -vate.5 Input Select/Indicators (C): Press the HDMI out “C” button repeatedly to switch to your desired source and the LED will illuminate to indicate which input source is being selected and routed to HDMI C output. When an HDMI or DVI source is connected the LED light labeled “HDMI/DVI” will activate. If the source is HDCP encrypted, the LED light labeled “HDCP” will acti -vate.6 Input Select/Indicators (D): Press the HDMI out “D” button repeatedly to switch to your desired source and the LED will illuminate to indicate which input source is being selected and routed to HDMI D output. When an HDMI or DVI source is connected the LED light labeled “HDMI/DVI” will activate. If the source is HDCP encrypted, the LED light labeled “HDCP” will acti -vate.7 HDCP Source light: When the input source(s) have HDCP , unit will detect the code and send to output source(s).8 HDMI/DVI Source light: When the input source(s) is HDMI format, the LED light will light up.213456781. Power: Press the button to turn on/off the unit.2. Input Select for HDMI OUT A:Press 1, 2, 3 or 4 to select the desired input source for HDMI OUT A.3. Input Select for HDMI OUT B:Press 1, 2, 3 or 4 to select the desired input source for HDMI OUT B.4. Input Select for HDMI OUT C:Press 1, 2, 3 or 4 to select the desired input source for HDMI OUT C.5. Input Select for HDMI OUT D:Press 1, 2, 3 or 4 to select the desired input source for HDMI OUT D.Pin Definition12345COMMAND ACTIONPOWER 00Power Off (standby) POWER 01Power OnPORT 11Output A select Input1 PORT 12Output A select Input2 PORT 13Output A select Input3 PORT 14Output A select Input4 PORT 21Output B select Input1 PORT 22Output B select Input2 PORT 23Output B select Input3 PORT 24Output B select Input4 PORT 31Output C select Input1 PORT 32Output C select Input2 PORT 33Output C select Input3 PORT 34Output C select Input4 PORT 41Output D select Input1 PORT 42Output D select Input2 PORT 43Output D select Input3 PORT 44Output D select Input4HD TV HD TVSTB DVDBlu-rayRS-232computer control portPS3HD TVHD TVFrequency bandwidth 2.25Gbps (single link)Input ports 4 x HDMI female portsOutput ports 4 x HDMI female portsEDID Standard, TV/Moving Port 1HDMI Audio output PCM2, PCM5.1, PCM7.1, Dolby5.1, DTS5.1, DD+, D- TrueHD, DTS-HDHDMI Cable in1080p 8bit (15M), 1080p 12bit (15M)HDMI Cable out1080p 8bit (15M), 1080p 12bit (6M)Color Space RGB_24/36,YCbCr 4:4:4_24/36, YCbCr 4:2:2,xvyccIR YesDeep Color1080p 12bitHDMI Resolution480I~1080p 50/60, 1080p 24, VGA~UXGADVI Resolution480I~1080p 50/60, 1080p 24, VGA~UXGAPower Supply5VDC/5A (US/EU standards, CE/FCC/UL certified)Dimensions (mm)438(W) x 175(D) x 49(H)Weight(g)3100Chassis Material MetalSilk Skin Color BlackOperating Temperature Operating from 0°C ~ 40°CPower Consumption16.5W(Max)SafeguardsTo reduce the risk of electric shock, do not expose this product to rain or moisture.If the wall plug does not fit into your local power socket, hire an electrician to replace your obsolete socket.Do not modify the wall plug.Doing so will void the warranty and safety features.This equipment should be installed near the socket outlet and the device shouldbe easily accessible in case it requires disconnection.PrecautionsFCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void theuser’s authority to operate this equipment.Operate this product using only the included external power supply. Use of other power supplies could impair performance, damage the product or cause fires.In the event of an electrostatic discharge, this device may automatically turn off. If this occurs, unplug the device, and plug it back in.Protect and route power cords so they will not be stepped on or pinched by anything placed on or against them. Be especially careful of plug-ins, or cord exit points from this product. Avoid excessive humidity, sudden temperature changes or temperature extremes.Keep this product away from wet locations such as bathtubs, sinks, laundries, wet basements and swimming pools.Use only accessories recommended by ATLONA to avoid fire, shock or other hazards.Unplug the product before cleaning. Usea damp cloth for cleaning. Do not use cleaning fluid or aerosols, which could enter the unit and cause damage, fire or electrical shock. Some substances may also mar the finish of the product.Never open or remove unit panels or make any adjustments not described in this manual. Attempting to do so could expose you to dangerous electrical shock or other hazards. It may also cause damage to your AT-HD-V44M. Opening the product will void the warranty.Do not attempt to service the unit. Instead disconnect it and contact your Authorized ATLONA reseller or contact ATLONA directly.1. LIMITED WARRANTYAtlona Technologies warrants that (a) its products (the “Product”) will perform substantially in accordance with the accompanying written materials for a period of 3 YEARS from the date of receipt and (b) that the Product will be free from defects in materials and workmanship under normal use and service for a period of 3 years. In the event applicable law imposes any implied warranties, the implied warranty period is limited to 3 years from the date of receipt. Some jurisdictions do not allow such limitations on duration of an implied warranty, so the above limitation may not apply to Customer.2. CUSTOMER REMEDIESAtlona Technologies and its suppliers’ entire liability and Customer’s exclusive remedy shall be, at Atlona Technolo-gies’ option, either return of the price paid for the Product, or repair or replacement of the Product that does not meet this Limited Warranty and which is returned to Atlona Technologies with a copy of Customer’s receipt. This Limited Warranty is void if failure of the Product has resulted from accident, abuse, or misapplication. Any replacement Prod-uct will be warranted for the remainder of the original warranty period or 3 year, whichever is longer.3. NO OTHER WARRANTIESTO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, ATLONA TECHNOLOGIES AND ITS SUPPLI-ERS DISCLAIM ALL OTHER WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WITH REGARD TO THE PRODUCT AND ANY RELATED WRITTEN MATERIALS. THIS LIMITED WARRANTY GIVES CUSTOMER SPECIFIC LEGAL RIGHTS. CUSTOMER MAY HAVE OTHER RIGHTS DEPENDING ON THE JU-RISDICTION.4. NO LIABILITY FOR DAMAGESTO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL ATLONA TECHNOLO-GIES OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER (INCLUDING WITHOUT LIMITA-TION, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR INDIRECT DAMAGES FOR PERSONAL INJURY, LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, OR ANY OTHER PECUNIARY LOSS) ARISING OUT OF THE USE OF OR INABILITY TO USE THIS PRODUCT, EVEN IF ATLONA TECHNOLOGIES HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN ANY CASE, ATLONA TECHNOLOGIES’ AND ITS SUPPLIERS’ ENTIRE LIABILITY UNDER ANY PROVISION OF THIS AGREEMENT SHALL BE LIMITED TO THE AMOUNT ACTUALLY PAID BY YOU FOR THE PRODUCT. BECAUSE SOME JU-RISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TO YOU.ATLONA2151 O’toole Ave, Ste DSan Jose CA 95131Toll Free: 1-877-536-3976International: 408-954-8782FAX: 408-954-8792Website: E-MAIL:***************。

A tlonA2x2 HDMI™ Matrix Switch HDMI™ version 1.3AT-HDMI-22M1. Introduction (1)2. Features (1)3. Package Contents (1)4. Operation Controls and Functions (2)4.1 Front Panel (2)4.2 Rear Panel (3)4.3 Remote Control (3)4.4 RS-232 Protocol (4)4.4.1 Pin Definition (4)4.4.2 Commands (4)5. Specifications (5)5.1 General Specification (5)5.2 Support Resolution (5)6. Connection and Installation (5)7. Safety (6)8. Warranty (7)AT-HDMI-22M is a high performance HDMI™ Matrix with remote control. It offers you maxi-mum convenience in HDMI™ signal distribution when you have multiple HDMI™ sources and displays to connect together. Each of the two HDMI™ sources can be directed to any one of the two outputs, so two displays can show 2 identical or 2 different sources at the same time. AT-HDMI-22M provides a maximum of 4 possible connection scenarios between sources and displays.When HDMI™ signal progresses through AT-HDMI-22M, it is re-timed, level compensated, phase error corrected, and data jitter eliminated, so the output is a regenerated brand new1. HDMI 1.3, HDCP 1.1 and DVI 1.0 compliant.2. HDMI input is compensated, clock / phase adjusted, and jitter eliminated so the output is a well tuned standard HDMI signal.3. Input source LED indicators on each output select.4. Ideal for home theater integration, conference room and retail stores.5. Compatible with all HDMI sources and displays.6. Supports high resolution input/output:PC: VGA, SVGA, XGA, SXGA and UXGA (1600X1200) &HDTV: 480i, 576i, 480p, 576p, 1080i, and 1080p7. RS-232 control.8. IR remote control.1. AT-HDMI-22M HDMI Matrix2. 5VDC Power Supply Adaptor3. Operation Manual4.1. Front Panel1. Remote control sensor.2. Power Switch & LED Indicator:The LED will illuminate when the power is turned on.3. Input Select/Indicators (A):Press the “HDMI OUT A” button repeatedly to switch to your desired source, and the LED will illuminate to indicate which input source is being selected, and routed to HDMI A dis-play.4. Input Select/Indicators (B):Press the “HDMI OUT B” button repeatedly to switch to your desired source, and the LED will illuminate to indicate which input source is being selected, and routed to HDMI Bdisplay.4.2 Rear Panel4.3 Remote Control 1. IR IN Socket:Plug the IR extender sensor (optional) into the socket for IR extension control.2. RS-232 Communication Port:Connect to the COM port of your PC for the distant control over RS-232 channel.3. HDMI inputs 1 and 2:Connect to the HDMI output of your source equipment such as DVD player or set-top-box.4. HDMI outputs A and B:Connect each of these output ports to the HDMI input of an HDMI display.5. Power:Plug the 5VDC power supply into the unit and connect the adaptor to AC wall outlet.1. Power:Press the button to turn on/off the unit.2. Input Select for HDMI OUT A:Press 1 or 2 to select the desired input source for HDMI OUT A.3. Input Select for HDMI OUT B:Press 1 or 2 to select the desired input source for HDMI OUT B.4. Void buttons (No function.)4.4 RS-232 Protocol4.4.1 Pin Definition*RS-232 transmission format:Baud Rate: 9600 bpsData bit: 8 BitsParity: NoneStop Bit: 1 bit4.4.2 CommandsCOMMAND ACTIONP0Power Off (standby) P1Power On *ST System Status *VR Firmware VersionA1Output A select Input1 A2Output A select Input2 B1Output B select Input1 B2Output B select Input2DVDPS3HDTV HDTV5.1 General Specification* Frequency bandwidth: 2.25Gbps (single link)* HDMI ™ v1.3* Input/Output: 2-in to 2-out HDMI female ports * 5V DC power supply* Dimensions: 240 (W) x 165 (D) x 49 (H)mm * Weight: 3.1Kgs 5.2 Support Resolution INTPUT PC VGA, SVGA, XGA, SXGA, UXGATV480i, 480p, 576i, 576p, 720p, 1080i, 1080pOUTPUTPC VGA, SVGA, XGA, SXGA, UXGATV480i, 480p, 576i, 576p, 720p, 1080i, 1080pSafeguardsTo reduce the risk of electric shock, do not expose this product to rain or moisture.If the wall plug does not fit into your local power socket, hire an electrician to replace your obsolete socket.Do not modify the wall plug.Doing so will void the warranty and safety features.This equipment should be installed near the socket outlet and the device shouldbe easily accesible in case it requires disconnection.PrecautionsFCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void theuser’s authority to operate this equipment.Operate this product using only the included external power supply. Use of other power supplies could impair performance, damage the product or cause fires.In the event of an electrostatic discharge, this device may automatically turn off. If this occurs, unplug the device, and plug it back in.Protect and route power cords so they will not be stepped on or pinched by anything placed on or against them. Be especially careful of plug-ins, or cord exit points from this product.Avoid excessive humidity, sudden temperature changes or temperature extremes.Keep this product away from wet locations such as bathtubs, sinks, laundries, wet basements and swimming pools.Use only accessories recommended by ATLONA to avoid fire, shock or other hazards.Unplug the product before cleaning. Usea damp cloth for cleaning. Do not use cleaning fluid or aerosols, which could enter the unit and cause damage, fire or electrical shock. Some substances may also mar the finish of the product.Never open or remove unit panels or make any adjustments not described in this manual. Attempting to do so could expose you to dangerous electrical shock or other hazards. It may also cause damage to your AT-HDMI-22M. Opening the product will void the warranty.Do not attempt to service the unit. Instead disconnect it and contact your Authorised ATLONA reseller or contact ATLONA directly.1. LIMITED WARRANTYAtlona Technologies warrants that (a) its products (the “Product”) will perform substantially in accordance with the accompanying written materials for a period of 3 YEARS from the date of receipt and (b) that the Product will be free from defects in materials and workmanship under normal use and service for a period of 3 years. In the event applicable law imposes any implied warranties, the implied warranty period is limited to 3 years from the date of receipt. Some jurisdictions do not allow such limitations on duration of an implied warranty, so the above limitation may not apply to Customer.2. CUSTOMER REMEDIESAtlona Technologies and its suppliers’ entire liability and Customer’s exclusive remedy shall be, at Atlona Technolo-gies’ option, either return of the price paid for the Product, or repair or replacement of the Product that does not meet this Limited Warranty and which is returned to Atlona Technologies with a copy of Customer’s receipt. This Limited Warranty is void if failure of the Product has resulted from accident, abuse, or misapplication. Any replacement Prod-uct will be warranted for the remainder of the original warranty period or 3 year, whichever is longer.3. NO OTHER WARRANTIESTO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, ATLONA TECHNOLOGIES AND ITS SUPPLI-ERS DISCLAIM ALL OTHER WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WITH REGARD TO THE PRODUCT AND ANY RELATED WRITTEN MATERIALS. THIS LIMITED WARRANTY GIVES CUSTOMER SPECIFIC LEGAL RIGHTS. CUSTOMER MAY HAVE OTHER RIGHTS DEPENDING ON THE JU-RISDICTION.4. NO LIABILITY FOR DAMAGESTO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL ATLONA TECHNOLO-GIES OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER (INCLUDING WITHOUT LIMITA-TION, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR INDIRECT DAMAGES FOR PERSONAL INJURY, LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, OR ANY OTHER PECUNIARY LOSS) ARISING OUT OF THE USE OF OR INABILITY TO USE THIS PRODUCT, EVEN IF ATLONA TECHNOLOGIES HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN ANY CASE, ATLONA TECHNOLOGIES’ AND ITS SUPPLIERS’ ENTIRE LIABILITY UNDER ANY PROVISION OF THIS AGREEMENT SHALL BE LIMITED TO THE AMOUNT ACTUALLY PAID BY YOU FOR THE PRODUCT. BECAUSE SOME JU-RISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TO YOU.ATLONA2151 O’toole Ave, Ste DSan Jose CA 95131Toll Free: 1-877-536-3976International: 408-954-8782FAX: 408-954-8792Website: E-MAIL:***************。

Atlona Manuals SwitchersA T -OME-MS52WApplication Programming Interface2.9.15x2 Matrix Switcherfor HDMI, USB-C, DisplayPort, and HDBaseT ™with USB and Wireless Link4K / UHDVersion InformationIntroductionRS-232 is often connected through a DB 9-pin to captive screw connector. The pins will have functions associated with them, some will be unassigned.Baud parameters must be met for control signals to pass. The parameters can be updated through the built in webGUI. The defaults for the RS-232 ports are: 9600, 8-bit, None, 1.RS-232A 3-pin captive screw connector has been included for RS-232.Pin out will be determined by the RS-232 cable and connect as RX (receive), TX (transmit) and GND (ground).NOTE: Typical DB9 connectors use pin 2 for TX, pin 3 for RX, and pin 5 for ground. On some devices functions of pins 2 and 3 arereversed.CommandsThe following is a list of Telnet commands for the AT-OME-MS52W. Commands are not case-sensitive. Do not change spacing or lettering. Each command is terminated with a carriage return. If the command fails or is entered incorrectly, then the feedback is “Unknown command”.Telnet CommandsIMPORTANT: Each command must be terminated with a carriage-return (0x0d) and the feedback is terminated with a carriage-return and line-feed (0x0a). In addition, when sending multiple commands, at least 500 milliseconds should be specified between each command.Displays a list of available commands. Note that the example feedback, below, is not a listing of all commands.To display help for a specific command, use the Helpcommand.This command does not require any parametersExampleFeedbackCommands Listing ---------------------------------------------------------------- - This listHelp - More detailed help on a specific commandQuit - End the sessionOutputMode - Change the output mode for all commandsMisc:Model:Get - Returns model number of the deviceMisc:Version:Get - Returns version numbers for the various subsystemsMisc:Versions:Get - Returns version numbers for the various subsystemsPlatform:Restart - Restarts the devicePlatform:Shutdown - Shutdown the devicePlatform:Reset - Factory Resets the device or certain subsystemsDisplay:Minimal:Set - Turn the Display on / off [ 0 - 1 ]Display:Minimal:Get - Get the Display on / offDisplay:Input:All:Get - Return the active inputsDisplay:Input:Get - Return the active inputDisplay:Input:Set - Changes the active inputDisplay:Input:HDCP:State:Get - Get the state of HDCP on an input on / offDisplay:Input:HDCP:State:Set - Turn HDCP on an input on / offDisplay:BYOD:Kick - Disconnects all existing BYOD clientsDisplay:Control:IP:Get - Return the Display Control IP address and portDisplay:Control:IP:Set - Sets the Display Control IP address and portGetInputStates - Return the state of all inputs.........Audio:GetBassReturns the current bass setting.ExampleAudio:GetBassFeedback { “result”: {“bass”: {“units”: “dB”, “value”: 0 } }, “methodreturn”: “Audio:GetBass”}This command does not require any parameters This command does not require any parameters Audio:GetSourceReturns the current audio source type. The returned value can be either digital or analog.ExampleAudio:GetSourceFeedback { “result”: {“audiosource”: “digital” }, “methodreturn”: “Audio:GetSource”}This command does not require any parameters Audio:GetTrebleReturns the current treble setting.ExampleAudio:GetTrebleFeedback { “result”: {“treble”: {“units”: “dB”, “value”: 0 } }, “methodreturn”: “audio:gettreble”}Audio:Mute:GetReturns the muting status.ExampleAudio:Mute:GetFeedback { “result”: {“outputmute”: {“analog”: false, “hdmi”: true } }, “methodreturn”: “Audio:Mute:Get”}This command does not require any parametersAudio:Mute:SetSets the muting for the HDMI or analog audio.ExampleAudio:Mute:Set hdmi trueFeedback { “result”: {“success”: true }, “methodreturn”: “audio:mute:set hdmi true”}Audio:SetBassSets the amount of bass effect applied to the audio output.ExampleAudio:SetBass 2Feedback { “result”: {“success”: true }, “methodreturn”: “audio:setbass 2”}Audio:SetSourceAssigns the input audio source.Audio:SetTrebleSets the amount of treble effect applied to the audio output.ExampleAudio:SetSource analogExampleAudio:SetTreble 5Feedback { “result”: {“success”: true }, “methodreturn”: “audio:setsource analog”}Feedback { “result”: {“success”: true }, “methodreturn”: “audio:settreble 5”}Audio:Volume:DecreaseDecreases the output volume by a specified amount. Values are measured in decibels.ExampleAudio:Volume:Decrease 20Feedback { “result”: { “volume”: -20,“success”: true }, “methodreturn”: “audio:volume:decrease 20”}Audio:Volume:GetReturns the current audio output level in decibels.ExampleAudio:Volume:GetFeedbackAudio:Volume:Get { "result": {"volume": {"units": "dB", "value": 0 } }, "methodreturn": "Audio:Volume:Get"}This command does not require any parametersAudio:Volume:IncreaseIncreases the output volume by a specified amount. Values are measured in decibels.ExampleAudio:Volume:Increase 25Feedback { “result”: { “volume”: 0,“success”: true }, “methodreturn”: “audio:volume:increase 25”}Audio:Volume:SetSets the overall audio output level in decibels.ExampleAudio:Volume:Set -10Feedback { “result”: {“success”: true }, “methodreturn”: “audio:volume:set -10”}Calendar:RefreshRefreshes the calendar.CEC:TrigSends the power-on or power-off command to the display using the CEC protocol. The first parameter specifies theoutput: 0 = HDBaseT; 1 = HDMI. The second parameter sets the power state of the display: 0 = off; 1 = on.ExampleCalendar:RefreshFeedback { “result”: {“response”: “” }, “methodreturn”: “calendar:refresh”, “jsonrpc”: “2.0”}This command does not require any parameters Example CEC:Trig 1 1Feedback { “result”: {“success”: true }, “methodreturn”: “cec:trig 1 1”}Display:BYOD:KickRemoves (“kicks”) the existing BYOD connection from the AT-OME-MS52W.This command does not require any parametersExampleDisplay:BYOD:KickFeedback{“result”: {“success”:true},“methodreturn”: “display:byod:kick”,“jsonrpc”: “2.0”}Display:Control:IP:GetReturns the IP address and port of the remote IP device, such as a display.This command does not require any parametersExampleDisplay:Control:IP:GetFeedback{“result”: {“port”:23,“ip”: “10.20.50.58”},“methodreturn”: “display:control:ip:get”,“jsonrpc”: “2.0”}Display:Control:IP:SetSets the IP address and port of the remote IP device, such as a display. The IP address must be specified in dot-decimal notation.ExampleDisplay:Control:IP:Set 10.20.50.58 23Feedback { “result”: {“success”: true }, “methodreturn”: “display:control:ip:set 10.20.50.58 23”, “jsonrpc”: “2.0”}Display:Input:All:GetReturns a list of all inputs and the current status. If an input is not active, false is returned. Otherwise, true is returned. For BYOD devices, the protocol will be displayed in the type key. Inputs are represented numerically:0 = USB-C, 1 = DisplayPort, 2 = HDMI, 3 = HDMI, 4 = BYOD.This command does not require any parametersExampleDisplay:Input:All:GetFeedback{“result”: {“0”: {“status”:false},“1”: {true“status”:},{“2”:true“status”:},{“3”:false“status”:},{“4”:“airplay”,“type”:“status”:false}},“methodreturn”: “display:input:all:get”,“jsonrpc”: “2.0”}Display:Input:GetReturns the active input. If no input is connected, then unknownis returned.ExampleDisplay:Input:GetFeedback { “result”: {“input”: 4,“type”: “airplay” }, “methodreturn”: “display:input:get”, “jsonrpc”: “2.0”}This command does not require any parameters Display:Input:HDCP:State:GetReturns the HDCP status of the specified input.ExampleDisplay:Input:HDCP:State:Get 0Feedback { “result”: {“state”: true }, “methodreturn”: “display:input:hdcp:state:get 0”}Display:Input:HDCP:State:SetSets the HDCP state on the specified input. When specifying the second argument, 0 = off, 1= on.ExampleDisplay:Input:HDCP:State:Set 0 1Feedback { “result”: {“success”: true }, “methodreturn”: “display:input:hdcp:state:set 0 1”}Display:Input:SetSets the active input.ExampleDisplay:Input:Set 1Feedback { “result”: { “activeinput”: 0 }, “methodreturn”: “display:input:set 0”, “jsonrpc”: “2.0”}Display:InputState:GetReturns the input state of the specified input. If 0 is returned, then no input is connected to the queried input. Otherwise, 1 will be returned for an input with a valid connection. Use values 0 through 4 to specifiy the input:0 = USB-C, 1 = DisplayPort, 2 = HDMI, 3 = HDMI, 4 = BYOD.ExampleDisplay:InputState:Get 1Feedback { “result”: { “input”: 1,“state”: false }, “methodreturn”: “display:inputstate:get 1”, “jsonrpc”: “2.0”}Display:Matrix:GetReturns the input for the specified output in Matrix Mode. Set the parameter to 0 to query the HDBaseT output orset to 1 to query the HDMI output.ExampleDisplay:Matrix:Get 1Feedback { “result”: {“input”: 4 }, “methodreturn”: “display:matrix:get 1”, “jsonrpc”: “2.0”}Display:Matrix:Mode:GetReturns the current Matrix Mode. If Matrix Mode is disabled, then the mode key will return false . When Matrix Mode is enabled, the mode key will return true and the mode will be displayed in the subtype key. Use the Display:Matrix:Mode:Setcommand to enable or disable Matrix Mode.ExampleDisplay:Matrix:Mode:GetReturns { “result”: {“mode”: true,“subtype”: “MATRIX_MODE_STATIC” }, “methodreturn”: “display:matrix:mode:get”, “jsonrpc”: “2.0”}This command does not require any parameters Display:Matrix:Mode:SetEnables or disabled Matrix Mode. 0 = Disable Matrix Mode; 1 = Matrix Mode; 2 = Matrix Mode with Static Route.ExampleDisplay:Matrix:Mode:Set 2Returns { “result”: {“success”: true }, “methodreturn”: “display:matrix:mode:set 2”}Display:Matrix:SetRoutes the specified input to the desired output. The arguments for the input parameter correspond to the following ports: 0 = USB-C (1), 1 = DP IN (2), 2 = HDMI IN (3), 3 = HDMI IN (4), 4 = BYOD. Set output=1 to use the HDMIoutput or set output=0 to use the HDBaseT output. If Matrix Mode is disabled, this command will return “CommandFailure”.ExampleDisplay:Matrix:Set 0 0Returns { “result”: {“success”: true }, “methodreturn”: “Display:Matrix:Set 0 0”, “jsonrpc”: “2.0”}Display:Minimal:GetReturns the state of the output display. If a display is not connected, then false will be returned. JSON structure isnot used in the return value.ExampleDisplay:Minimal:Get Returns onThis command does not require any parametersDisplay:Minimal:SetSets the state of the output display. If a display is not connected, then falsewill be returned.ExampleDisplay:Minimal:Set 1Returns { “result”: {“success”: true }, “methodreturn”: “display:minimal:set 1”}GetBroadcastReturns the current broadcast setting. JSON structure is not used in the return value.Example GetBroadcast OffThis command does not require any parametersGetHostNameReturns the hostname of the AT-OME-MS52W.This command does not require any parametersExampleGetBroadcastReturns{“result”: {“ms52w-34e4”“hostname”:},“methodreturn”: “gethostname”}GetInputStatesReturns the state of each input on the AT-OME-MS52W. JSON structure is not used in the return value. A value ofindicates no source connected.true indicates that the input has a valid source connection. A value of falseThis command does not require any parametersExampleGetInputStatesReturns[GetInputState 0 false, GetInputState 1 false, GetInputState 2 true, GetInputState 3 false, GetInputState 4 true]GetNoSignalTimeoutReturns the current time interval which must elapse before the connected display is powered-off.ExampleGetNoSignalTimeoutReturns { “result”: {“units”: “seconds”, “value”: 0 }, “methodreturn”: “getnosignaltimeout”}HelpReturns additional information about the specified command. JSON structure is not used in the return value.ExampleHelp Display:Minimal:SetReturnsDisplay:Minimal:Set <value> value - 0 = off1 = onInput:GetReturns the active input. If no input is connected, then unknownis returned.Example Input:GetFeedback { “result”: {“input”: 4,“type”: “airplay” }, “methodreturn”: “input:get”, “jsonrpc”: “2.0”}This command does not require any parameters Input:SetSets the active input.Example Input:Set 1Feedback { “result”: { “activeinput”: 0 }, “methodreturn”: “input:set 0”, “jsonrpc”: “2.0”}Instruments:Temperature:GetReturns the internal temperature of the AT-OME-MS52W. If the units parameter is not specified, then the temperaturewill be displayed in Celsius. Specify c for Celsius, f for Fahrenheit, or k for Kelvin.ExampleInstruments:Temperature:GetReturns { “result”: {“scale”: “Celcius”, “value”: 50 }, “methodreturn”: “instruments:temperature:get”}Misc:Model:GetReturns the SKU of the AT-OME-MS52W.ExampleMisc:Model:GetReturns { “result”: {“model”: “AT-OME-MS52W” }, “methodreturn”: “misc:model:get”}This command does not require any parametersExampleMisc:Version:Get mcuReturns { “result”: {“version”: { “mcu”: “1.0.00” } }, “methodreturn”: “misc:version:get mcu”}Misc:Version:GetReturns the hardware version of the AT-OME-MS52W. If no parameters are specified, then the master firmwareversion is returned.Misc:Versions:GetReturns both the MCU and master firmware versions of the AT-OME-MS52W.This command does not require any parameters ExampleMisc:Versions:GetReturns { “result”: {“versions”: { “mcu”: “V1.0.00”, “master”: “2.8.1” } }, “methodreturn”: “misc:versions:get”}Moderator:Enable:GetReturns the current status of Moderator mode. If Moderator Mode is disabled, then false is returned.This command does not require any parametersExampleModerator:Enable:GetReturns{“result”: {true“enable”:},“methodreturn”: “moderator:enable:get”,“jsonrpc”: “2.0”}Moderator:Enable:SetEnable or disable Moderator mode. Specify 1 to enable Moderator mode or 0 to disable. Two JSON structures are returned.ExampleModerator:Enable:Set 1Returns{“result”: {true“success”:},“methodreturn”: “moderator:enable:set 1”}{“jsonrpc”: “2.0”,“event”: {{“moderator”:“streams”: [],“activeindex”: -1,true“enabled”:}}}Moderator:KickKicks the specified BYOD ID from the system.ExampleModerator:Kick 2Returns{“result”: {true“success”:},“methodreturn”: “Moderator:Kick 2”}Moderator:ShowSets the active BYOD device ID for casting.ExampleModerator:Show 2Returns{“result”: {true“success”:},“methodreturn”: “Moderator:Show 2”}Moderator:Status:GetReturns the current status of Moderator mode.This command does not require any parameters ExampleModerator:Status:GetReturns{“methodreturn”: “moderator:status:get”,“moderator”: {“streams”: [2],“activeindex”: 1,true“enabled”:},“jsonrpc”: “2.0”}Returns { “result”: {“netinfo”: { “wlan0”: {“mode”: “access point”, “txbytes”: 322684, “txpackets”: 1119, “netmask”: “255.255.255.0”, “ip”: “192.168.43.1”, “rxbytes”: 0, “mac”: “74:da:38:ef:db:e8”, “rxpackets”: 9841, “ap”: { “channel”: 165, “ssid”: “ms52w-b500” } }, “eth0”: {“mode”: “dynamic”, “txbytes “: 281994851, “txpackets “: 1268641, “netmask”: “255.255 .255 .0”, “ip”: “10.20 .20 .32 “, “rxbytes”: 286555191, “mac”: “00:1e:06:36:b5:00 “, “rxpackets”: 2845101 } } }, “methodreturn”: “net: getinfo “}Net:GetInfoReturns information about the physical and wireless network interfaces.This command does not require any parameters Example Net:GetInfoOutputModeSets the output mode for command feedback, where h = human-readable, j = JSON (compact), p = JSON (“pretty”). To display without using JSON data structures, specify the h parameter.The following examples illustrate the effect on command feedback, after executing the OSD:State:Getcommand.ReturnsOutputMode is Human ReadableExampleOutputMode hPlatform:ResetResets the AT-OME-MS52W to factory-default settings. Network settings are preserved, unless otherwise specifiedby the second parameter. This parameter is optional.Returns { “result”: {“success”: true }, “jsonrpc”: “2.0”}ExamplePlatform:Reset allPlatform:RestartReboots the AT-OME-MS52W.ExamplePlatform:RestartReturns { “result”: {“success”: true }, “jsonrpc”: “2.0”}This command does not require any parametersPlatform:ShutdownShuts down the power to the AT-OME-MS52W. This command should be performed before disconnecting the powerfrom the unit.ExamplePlatform:ShutdownReturns { “result”: {“success”: true }, “jsonrpc”: “2.0”}Example QuitReturnsConnection closed by foreign host.Session closed.This command does not require any parameters QuitEnds the Telnet session.This command does not require any parametersRelay:PulseDuration:GetReturns the current pulse duration of the relay.Relay:PulseDuration:SetSets the relay pulse duration.Returns { “result”: { “duration”: 1 }, “methodreturn”: “relay:pulseduration:get”}Returns { “result”: {“success”: true }, “methodreturn”: “relay:pulseduration:set 2”}ExampleRelay:PulseDuration:GetExampleRelay:PulseDuration:Set 2This command does not require any parametersRelay:State:GetReturns the current state of the specified relay.ExampleRelay:State:Get 0Returns { “result”: {“state”: true }, “methodreturn”: “relay:state:get 0”}Relay:State:SetSets the state of the specified relay. The relay can be normally-open (NO) or normally-closed (NC).ExampleRelay:State:Get 0 1Returns { “result”: {“success”: true }, “methodreturn”: “relay:state:set 0 1”}SetBroadcastEnables or disables broadcast mode. When set to on , any state change to the AT-OME-MS52W will be reflected through RS-232, Telnet, and TCP port 9000. State changes can be caused by modification of the web server,physical connection/disconnection of source/sink and additional Telnet/TCP clients making changes. 1 = broadcast enabled; 0 = broadcast disabled. The default setting is on. JSON structure is not used in the return value.ExampleSetBroadcast 1ReturnsBroadcast onSetVolShortened command for setting the audio volume commands. The command argument can be any one of the following:+ increment volume by 1 dB. - decrement volume by 1 dB. stareturns the current SetVol value.Example SetVol +Returns { "result": { "volume": 0,"success": true }, "methodreturn": "setvol +"}USBRouting:Follow:InputAssigns the video input with the specified USB host when using Follow USB mode.ExampleUSBRouting:Follow:Input 2 1Returns { "result": {"success": true }, "methodreturn": "usbrouting:follow:input 2 1"}USBRouting:Input:GetReturns the USB host and corresponding input for the Manual USB Routing mode.ExampleUSBRouting:Input:GetReturns { "result": { "input": 1, "host": "1" }, "methodreturn": "usbrouting:input:get", "jsonrpc": "2.0"}This command does not require any parametersUSBRouting:Input:SetSets the active USB host port.1 USB host 1 2 USB host 2 3 Remote host 4USB-CExampleUSBRouting:Input:Set 2Returns { "result": {"success": true }, "methodreturn": "usbrouting:input:set 2"}USBRouting:Mode:GetReturns the USB routing mode.ExampleUSBRouting:Mode:GetReturns { "result": {"mode": "AUTOSWITCH" }, "methodreturn": "usbrouting:mode:get", "jsonr pc ":" 2.0 "}This command does not require any parametersUSBRouting:Mode:SetSets the USB routing mode.ExampleUSBRouting:Mode:Set manualReturns { "result": {"success": true }, "methodreturn": "usbrouting:mode:set manual"}Zone:PortParamsReturns the current RS-232 settings for the specified zone. 1 = RS-232 port; 2 = HDBaseT OUT port.ExampleZone:PortParams 1Returns { “result”: { “zone”: 1, “params”: “[9600,8,0,1]” }, “methodreturn”: “zone:portparams 1”}AT-OME-MS52W 41CommandsZone:PortSetupSets the RS-232 settings for the specified zone. 1 = RS-232 port; 2 = HDBaseT OUT port.ExampleZone:PortSetup 1 19200 8 0 1Returns { “result”: {“success”: true }, “methodreturn”: “zone:portsetup 1 19200 8 0 1”}Zone:SendCmdSends an RS232 command to the specified zone. 1 = RS-232 port; 2 = HDBaseT OUT port.ExampleZone:SendCmd 1 vol+Returns { “result”: {“success”: true }, “methodreturn”: “zone:sendcmd 1 vol+”}T oll free US International • 877.536.3976 • 41.43.508.4321© 2020 Atlona Inc. All rights reserved. “Atlona” and the Atlona logo are registered trademarks of Atlona Inc. All other brand names and trademarks or registered trademarks are the property of their respective owners. Pricing, specifications and availability subject to change without notice. Actual products, product images, and online product images may vary from images shown here.。

USER MANUALDesigned and Manufactured in the USA1-800-284-2131SM-MST-2D 2-Port KVM MST with Dual 4K HDMI Out SM-MST-2Q 2-Port KVM MST with Quad 4K HDMI Out SM-MST-4D 4-Port KVM MST with Dual 4K HDMI Out SM-MST-4Q4-Port KVM MST with Quad 4K HDMI OutOVERVIEWTECHNICAL SPECIFICATIONS_________________________________________________________________ WHAT’S IN THE BOX?_________________________________________________________________________ FRONT AND BACK___________________________________________________________________________ INSTALLATION_______________________________________________________________________________ SYSTEM OPERATION_________________________________________________________________________ FRONT PANEL CONTROL_____________________________________________________________________ HOTKEY AND RS232 SERIAL CONTROL_______________________________________________________ CUSTOM HOTKEY TRIGGERS_________________________________________________________________ LED’S BEHAVIOUR___________________________________________________________________________ TROUBLESHOOTING_________________________________________________________________________ TECHNICAL SUPPORT________________________________________________________________________ LIMITED WARRANTY STATEMENT____________________________________________________________3 4 4 5-6 7 7 7 8 9 10 10 11Technical SpecificationsFRONT AND BACKSM-MST-2D Back SM-MST-2D BackSM-MST-2Q BackSM-MST-2D FrontSM-MST-2Q FrontSM-MST-2Q BackSM-MST-2D FrontSM-MST-2Q FrontWhat’s in the box?INSTALLATION1. Ensure that power is turned off or disconnected from the unit and the computers.2. Use a DisplayPort cable to connect the DisplayPort output port from each computer to thecorresponding DP IN ports of the unit.3. Use a USB cable (Type-A to Type-B) to connect a USB port on each computer to the respectiveUSB ports of the unit.4. Optionally connect a stereo audio cable (3.5mm to 3.5mm) to connect the audio output of thecomputers to the AUDIO IN ports of the unit.5. Connect a monitor to the HDMI OUT console port of the unit using a HDMI cable.6. Connect a USB keyboard and mouse in the two USB console ports.7. Optionally connect stereo speakers to the AUDIO OUT port of the unit.8. Optionally use included 3.5mm to DB9 Cable and connect with a standard RS-232 Cable (notincluded) to connect to a PC for Serial Control (only for 2 port units)9. Finally, power on the KVM by connecting a 12VDC power supply to the power connector, and thenturn on all the computers.Note: You can connect up to 2 computers to the 2 port KVM and connect up to 4 computersto the 4 port KVM.Installation (continued)EDID LEARNThe KVM is designed to learn the connected monitor’s EDID upon power up. In the event of connecting a new monitor to the KVM, a power recycle is required.The KVM will indicate to the user the EDID learn process by flashing the front panel’s LEDs. Port one green and push button blue LEDs will both begin to flash for about 10 seconds. When the LEDs stop flashing, the EDID learn process is done.If the KVM has more than one video board (such as dual-head and quad-head models), then the unit will continue to learn the EDIDs of the connected monitors and indicate the progress of the process by flashing the next port selection green and push button blue LEDs respectively.The monitor must be connected to the video output connector located in the console space at the back of the KVM during the EDID learn process.If the read EDID from the connected monitor is identical to the current stored EDID in the KVM then the EDID learn function will be skipped.System operationhotkey and rs232 serial controlThere are three ways to control the SM-MST: Keyboard Hotkeys, RS-232 Serial Commands, and Front Panel Buttons. All modes of control will allow the user the set their desired configurations.The SM-MST may also be controlled via RS-232 commands. T o use these commands, you must use HyperT erminal or an alternate terminal application. The settings for the connection are as follows:Baudrate 115200; Data Bits 8; Parity None ; Stop Bits 1; Flow Control None .Once you have connected to the SM-MST via Serial, you will see the SM-MST information when the device starts up.The following commands can be used for RS-232 with available keyboard hotkeys:front panel controlT o switch to an input port, simply push the button on the front-panel of the KVM. If an input port is selected, the LED of that port will turn on.Hold down the button of Front Panel for 3 seconds to force learn EDID.Custom hotkey triggersUsers are able to customize the keys that trigger Hotkeys. The default trigger for hot key function on the keyboard is Ctrl + Ctrl. The trigger function can be used to change to the following keys:Ctrl (Left / Right), Alt, Shift (Left / Right), Caps Lock, Scroll Lock, F1-F12TO VIEW HOTKEY TRIGGER SETTINGUse the RS-232 command: / + / + ? + ? + Enter to view the current HotKey Trigger T o reset the Hotkey Trigger use the “Factory Defaults” command.TO CHANGE THE HOTKEY TRIGGER SETTINGHotKey + HotKey + x + [desired hotkey]Example: If users current Hotkey trigger is Shift and want to change to Scroll Lock, user would type Shift + Shift + x + Scroll LockLed’s behaviorUser Console Interface – Display LED:Front Panel – Port Selection LED’s:EDID Learn - Front Panel LED’s:All LED’s are turned on for 1 second. Then:• Port 1 LED’s will flash until the end of the process.• Port 2 LED’s will flash until the end of the process if a second video board exists (Dual-head KVM)IMPORTANT!If all Front Panel LED’s are on and not flashing , the POWER UP SELF TEST has failed and all functions are disabled. Check if any of the front panel port selection buttons are jammed. In this case, release thejammed button and recycle the power. If power up self test is still failing, please contact SmartAVI technical support at ********************.TroubleshootingTechnical supportNo Power• Make sure that the power adapter is securely connected to the power connector of the unit.• Check the output voltage of the power supply and make sure that the voltage value is around 12VDC.• Replace the power supply. No Video• Check if all the video cables are connected properly.• Connect the computer directly to the monitor to verify that your monitor and computer are functioning properly.• Restart the computers. Keyboard is not working• Check if the keyboard is properly connected to the unit.• Check if the USB cables connecting the unit and the computers are properly connected.• Try connecting the USB on the computer to a different port.• Make sure that the keyboard works when directly connected to the computer.• Replace the keyboard. Mouse is not working• Check if the mouse is properly connected to the unit.• Try connecting the USB on the computer to a different port.• Make sure that the mouse works when directly connected to the computer.• Replace the mouse.No Audio• Check if all the audio cables are connected properly.• Connect the speakers directly to the computer to verify that the speakers and the computer audio are functioning properly.• Check the audio settings of the computer and verify that the audio output is through the speakers.For product inquiries, warranty questions, or technical questions, please contact *****************.Limited warranty statementA. Extent of limited warrantySmartAVI, Inc. warrants to the end-user customers that the SmartAVI product specified above willbe free from defects in materials and workmanship for the duration of 1 year, which duration begins on the date of purchase by the customer. Customer is responsible for maintaining proof of date of purchase.SmartAVI limited warranty covers only those defects which arise as a result of normal use of the product, and do not apply to any:a. Improper or inadequate maintenance or modificationsb. Operations outside product specificationsc. Mechanical abuse and exposure to severe conditionsIf SmartAVI receives, during applicable warranty period, a notice of defect, SmartAVI will at its discretion replace or repair defective product. If SmartAVI is unable to replace or repair defective product covered by the SmartAVI warranty within reasonable period of time, SmartAVI shall refund the cost of the product.SmartAVI shall have no obligation to repair, replace or refund unit until customer returns defective product to SmartAVI.Any replacement product could be new or like new, provided that it has functionality at least equal to that of the product being replaced.SmartAVI limited warranty is valid in any country where the covered product is distributed by SmartAVI.B. Limitations of warrantyT o the extant allowed by local law, neither SmartAVI nor its third party suppliers make any other warranty or condition of any kind whether expressed or implied with respect to the SmartAVI product, and specifically disclaim implied warranties or conditions of merchantability, satisfactory quality, and fitness for a particular purpose.C. Limitations of liabilityT o the extent allowed by local law the remedies provided in this warranty statement are the customers sole and exclusive remedies.T o the extant allowed by local law, except for the obligations specifically set forth in this warranty statement, in no event will SmartAVI or its third party suppliers be liable for direct, indirect, special, incidental, or consequential damages whether based on contract, tort or any other legal theory and whether advised of the possibility of such damages.D. Local lawT o the extent that this warranty statement is inconsistent with local law, this warranty statement shall be considered modified to be consistent with such law.NOTICEThe information contained in this document is subject to change without notice. SmartAVI makes no warranty of any kind with regard to this material, including but not limited to, implied warranties of merchantability and fitness for particular purpose. SmartAVI will not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance or use of this material. No part of this document may be photocopied, reproduced, or translated into another language without prior written consent from SmartAVI, Inc.20180109Designed and Manufactured in the USAT el: (800) AVI-2131 • (702) 800-00052455 W Cheyenne Ave, Suite 112North Las Vegas, NV 89032。