KIA278R系列整流器规格书

铝电解电容器Aluminum Electrolytic Capacitors GR Series特性FEATURES⚫105℃⚫寿命(Life time):2000~3000 Hours⚫高纹波(High ripple current)、低阻抗(Low Impedance)主要技术性能Specifications项目Item 特性Performance Characteristics使用温度范围Operating Temperature Range-40 ~ +105℃额定电压范围Rated Working Voltage Range6.3 ~ 100V标称电容量范围Nominal Capacitance Range15 ~ 4700μF标称电容量允许偏差Capacitance Tolerance±20%(120Hz,+20℃)漏电流Leakage Current L≤0.01CV or 3(μA) 测试时间2分钟取最大值，测试温度20℃；Whichever is greater measured after 2 minutes application of ratedworking voltage at +20℃损失角正切值tan δ(120Hz,+20℃)工作电压(Voltage) 6.3 10 16 25 35 50 63 100 tan δ(max)0.22 0.19 0.16 0.14 0.12 0.10 0.09 0.08 容量大于1000μF，每增加1000μF损耗值增加0.02For capacitance value>1000μF,app 0.02 per another 1000μF低温特性(120Hz)Low Temperature Characteristics 工作电压(Voltage) 6.3 10 16 25 35 50 63 100 Z-25℃/Z+20℃ 4 3 2 2 2 2 2 2 Z-40℃/Z+20℃8 6 4 3 3 3 3 3高温负荷High Temperature Loading 负荷寿命(Load Life) 2000Hrs(D:5~6.3) 3000Hrs(D≥8)试验条件(Test conditions)温度(Temp.) 105℃输入工作电压纹波电流（Input working Voltage andripple current)容量变化率(Cap.) 容量变化为初始值的±20% (Within ±20% of Initial Value)损失角(tan δ) 小于等于初始值200% (200% or less of Initial Specified Value)漏电流(LC) 小于规格值(Initial Specified Value or less)高温无负荷Shelf Life 无负荷寿命(Shelf life) 1000 Hrs试验条件(Test conditions) 温度(Temp.) 105℃容量变化率(Cap.) 容量变化为初始值的±20% (Within ±20% of Initial Value)损失角(tan δ) 小于等于初始值200% (200% or less of Initial Specified Value) 漏电流(LC) 小于规格值(Initial Specified Value or less)纹波电流与频率补正系数Ripple Current & Frequency MultipliersFreq.(Hz)Cap.(μF)50(60) 120 1K 10K 100K ≤100 0.40 0.55 0.75 0.90 1.00100~1000 0.60 0.70 0.85 0.95 1.00≥1000 0.65 0.80 0.95 0.98 1.00参照标准Standards JIS- C-5101-4 (IEC 60384)尺寸图(Diagram of Dimensions)：.尺寸(Diameter): 单位(Unit):mmD 5 6.3 8(L<20) 8(L≥20) 10 13F 2.0 2.5 3.5 5.0d 0.5 0.5 0.6 0.6 0.6α(L<20)1.5 (L≥20)2.0β(D<20)0.5 (D≥20)1.0Voltage(Code) 6.310 16 Cap.(μF) D x L IMP R.C D x L IMP R.C D x L IMP R.C 100 5*11 0.580 140 5*11 0.58 140 6.3*12 0.250 300 120 5*11 0.530 165 5*11 0.53 140 6.3*12 0.250 320150 6.3*12 0.250 185 6.3*12 0.25 340 6.3 *12 0.220 340 8*12 0.150 500180 6.3*12 0.250 255 6.3*12 0.250 340 6.3*12 0.220 340 8*12 0.150 580220 6.3*12 0.250 275 6.3*12 0.220 340 6.3*12 0.220 340 8*12 0.150 600270 6.3*12 0.220 280 6.3*12 0.220 3408*12 0.150 640 8*12 0.130 580330 6.3*12 0.220 340 6.3*12 0.220 3408*12 0.130 640 8*12 0.130 580 8*12 0.130 640390 8*12 0.130 600 8*12 0.130 640 8*12 0.130 640470 8*12 0.130 640 8*12 0.130 6408*12 0.130 640 10*13 0.100 865560 8*12 0.130 640 8*12 0.130 640 10*13 0.100 880680 8*12 0.130 640 8*12 0.130 6408*16 0.087 750 10*13 0.087 8658208*12 0.130 64010*13 0.080 865 10*17 0.075 1210 10*13 0.110 86510008*12 0.130 640 8*16 0.087 76010*17 0.075 1210 10*13 0.087 865 10*17 0.075 121012008*16 0.096 84010*20 0.060 1400 10*20 0.060 1400 10*13 0.087 88015008*20 0.069 105010*20 0.060 1430 10*20 0.060 1430 10*17 0.069 12101800 10*20 0.060 1400 10*20 0.060 1460 10*25 0.052 1650 13*20 0.046 19002200 10*20 0.060 1460 10*20 0.060 1490 13*20 0.045 19202700 10*25 0.050 1650 10*25 0.050 1650 13*25 0.040 2124 13*20 0.050 1650 13*20 0.035 19003300 10*25 0.050 165013*25 0.030 2124 13*20 0.050 18703900 13*20 0.046 19004700 13*25 0.046 2124﹡13mm may be replaced by 12.5mm upon customer’s request.Voltage(Code) 2535 50 Cap.(μF) D x L IMP R.C D x L IMP R.C D x L IMP R.C33 6.3*12 0.500 23039 6.3*12 0.500 26547 6.3*12 0.250 300 6.3*12 0.500 29556 6.3*12 0.250 315 8*12 0.420 51568 6.3*12 0.240 340 8*12 0.420 53582 6.3*12 0.220 320 8*12 0.230 625 8*12 0.420 555100 6.3*12 0.220 340 8*12 0.220 640 10*13 0.200 760120 8*12 0.200 565 8*12 0.200 6558*16 0.200 730 10*13 0.200 780150 8*12 0.180 580 8*12 0.180 670 10*17 0.130 825180 8*12 0.150 600 10*13 0.130 7608*20 0.130 825 10*17 0.130 855220 8*12 0.130 6208*12 0.130 64010*17 0.130 875 8*16 0.100 83010*13 0.100 8302708*12 0.130 64010*17 0.075 1210 10*25 0.093 1025 10*13 0.100 8253308*12 0.130 6658*20 0.087 105013*20 0.090 166010*17 0.075 86510*13 0.100 845 10*17 0.075 1210390 10*13 0.100 865 10*17 0.075 1210 13*20 0.090 16804708*16 0.087 84010*17 0.075 1210 13*25 0.088 1950 10*13 0.100 885560 10*17 0.075 1210 10*20 0.060 1380 13*25 0.088 1970 680 10*17 0.075 1210 10*20 0.058 1400820 10*20 0.060 1370 10*25 0.054 1650 13*20 0.046 19001000 10*20 0.058 1400 13*20 0.046 1920 13*25 0.042 21241200 10*20 0.055 14201500 10*25 0.050 1650 13*20 0.047 19001800 13*25 0.043 21042200 13*25 0.040 2124Voltage(Code) 63100 Cap.(μF) D x L IMP R.C D x L IMP R.C15 6.3*12 1.880 11522 6.3*12 1.050 115 8*12 1.530 23027 6.3*12 1.050 120 8*12 1.320 23233 6.3*12 1.050 125 8*12 1.280 33039 8*12 0.800 200 8*16 0.980 30047 8*12 0.780 212 10*13 0.650 37056 8*12 0.760 222 8*20 0.480 36268 10*13 0.750 234 10*17 0.460 35782 10*13 0.700 314 10*20 0.430 4661008*16 0.630 30010*20 0.430 480 10*13 0.580 314120 10*17 0.324 357 13*20 0.368 530 150 8*20 0.324 362 13*20 0.357 680 180 10*20 0.190 466 13*25 0.328 750 220 10*20 0.190 466 13*25 0.328 880 270 13*20 0.128 670330 13*20 0.128 690390 13*25 0.118 922﹡13mm may be replaced by 12.5mm upon customer’s request.。

1Environmental SpecificationsItemSpecificationOperatingtemperature –40ºC to +75 ºC (referring to Figure 3) (–40°F to +167°F)Storage temperature–40ºC to +75ºC (not packaged) (–40°F to +167°F)Relative humidity 5%-95% (non-condensing) Altitude range≤ 4000 mItem SpecificationInputOperating voltage 85–300 V ACRated: 200–240 V AC and 100–120 V ACFrequency 45–66 HzRated: 50 Hz and 60 Hz Maximum input current ≤ 6.4 APower factor ≥ 0.99 (100% load) THD ≤ 3.5% (full load) ; ≤ 5% (load ≥ 50%)Output Output voltage42–58 V DCRated voltage: 53.5 V DCOutput power1000 W (176–300 V AC);470 W (85–175 V AC decreased linearly) Regulated voltage precision ≤ ±0.6%VoRipple and noise≤ 200 mVp -p(Bandwidth ≤ 20M Hz) Dynamic response •25-50% or 50-75% load−Over shoot:≤ ±5%−Recovery time: ≤ 200 us (±0.6%)•10-90% load;−Over shoot:≤ ±5%;−Recovery time: ≤ 1ms (±1%) Standby power ≤ 5 W Turn-on output delay 3–8s Hold up time > 10 ms Psophometrically weighted noise ≤ 2 mVBroad frequency noise voltage ≤ 50 mV (3.4–150 kHz) ≤ 20 mV (0.15–30 MHz)Electrical SpecificationsEfficiencyThe peak point is ≥ 94%≥ 93% (230 V AC, 30%–100% load)Height x Width x Depth 40.8 mm x 95.5 mm x 208 mm (1.61 in. x 3.76 in. x 8.19 in.) Weight About 1.1 kgCoolingBuilt-in fan (The rotation of fan dependson the internal temperature.)DescriptionThe R4815N1 is a digital rectifier with high efficiency and power density. It converts 85–300 V AC input voltage to 53.5 V DC output voltage. The output voltage can be adjusted by the host.It performs comprehensive protection functions, supports soft start, and produces low noise. With the latest power monitoring technology, states of the rectifier and load are monitored in real time.Multiple rectifiers can be paralleled.Key Features•Input voltage range: 85–300 V AC•Operating temperature range: –40ºC to +75ºC •Total harmonic distortion (THD): ≤ 3.5％ •Digital control mode •Hot swap•Supports intelligent electric meter •Supports CAN communication •Supports LED display•Supports voltage adjustment,current adjustment,and current sharing •Meet Rohs requirement•Passes the TUV, CE, UL certifications and gets the CB certifIcate. •Disconnect above 320 V ACNote : If the altitude is within the range of 3000 m to 4000 m, the maximum operatingtemperature decreases by 1°C (1.8°F ) as the altitude increases by 200 m.Copyright © Huawei Technologies Co., Ltd. 2016. All rights reserved.2Item SpecificationProtectionInput overvoltage protection Protection point: > 300 V AC Recovery range: 290-300 V AC Input undervoltage protectionProtection point: < 80 V AC Recovery range: 70-85 V AC Output overvoltage protection56–60V DC(can be set by monitoring unit)1.If the overvoltage occurs inside the rectifier due to a fault, the rectifier will latch off.2.If the output voltage is higher than 63 V and lasts for more than 500 ms, the rectifier will latch off. Output currentlimiting protection See Figure 1.Output short circuit protectionA long term short circuit is allowed. After the fault is rectified, the rectifier is restored to a healthy state automatically.Over-temperature protectionThe module protects against overtemperature.Safety/EMC/Lightening protectionSafetycertificationPasses TUV, CE, UL certifications. Catch the CB certificate. Complies with UL60950-1; IEC60950-1; EN60950-1;CAN/CSA C22.2 No. 60950-1; EMCEN55022 Class B ; EN55024; EN61000-3-2; EN61000-3-3; ETSI EN300 386; ETSI EN301489; ITU-T K.20; Lightning5 kAReliabilityMTBF> 500,000 hoursAudible NoiseSpecification≤ 40 dB (25ºC /77°F , full load)Output FeatureFigure 1 Output featureFigure 2 Efficiency(Vin = 230 V AC, Vout = 53.5 V, Ta: 25ºC)Figure 3 Power derating curveOther Features020040060080010001200-40-2020406080P o (w )Ta(℃)Power Derating Curve3 Interface DescriptionThe rear panel of the rectifier provides an golden finger connection which is used as AC input, DC output and signal connection.For the location of the pins, see Figure 3. For the definitions of the pins, see Table 1. Figure 4 Pins on the rear panelTable 1 Definitions of the pins on the rear panelPinDefinitionFunction1, 9 L Live line 2, 10 N Neutral line 3, 11 PE Protect earth 4 CANL CANL13 ACD1 Slot detection signal 1 5 ACD2 Slot detection signal 2 12 CANH CANH 6, 14 OUTPUT+ Output:48V+ 8 OUTPUT- Output:48V- 7Pre-chargePre-chargeRemoving the RectifierFigure 5 Removing a PSUStep 1: Push the locking latch left.Step 2: Remove the PSU out of the PDU byexternally drawing the handle, as shown in Figure 5.Installing the RectifierFigure 6 Installing a PSUStep 1: Push the locking latch left and pull out thehandle. Step 2: Push the PSU slowly into the subrackalong the guide rail and push the locking latch right to fix the handle, as shown in Figure 6.TransportThe product must be packed with firmly packing box when transport. Out of the box the mark“prevent moisture”, “lay down carefully” and other required mark must have. Any transport tools are permitted if the product in the packing box. When transport must avoid rain and snow attack directly and mechanical shock.StorageProduct should be packaged in the packing box before use. The store room should be meet: -40ºC to +70ºC ambient temperature, relatedhumidity less than 80%, dry, ventilation and hasn’t any corrosive gas.•Only trained and qualified personnel can be allowed to install or service the rectifier.•Each rectifier input is protected by two fuses, one for the live wire and the other for the neutral wire.CAUTION•This product should be used in the environment that meets specifications described in the user manual.•If the product is used with abnormal power grid input orexposed to salt mist, dust, or mist, the product may become faulty, and the resulting product exceptions or component damage are beyond the warranty scope.CAUTION4Indicator Color StatusDescriptionMeasuresPower indicatorGreen Steady on The rectifier is supplied with alternating current (AC) input power.The rectifier runs properly, and no measure is required.OffThe rectifier is not supplied with AC input power. Replace the rectifier if the AC input is normal.The rectifier is faulty.Replace the rectifier. Blinking at 0.5 HzThe rectifier is being queried.No measure is required.Blinking at 4 HzThe rectifier is loading an application program. The rectifier automatically recovers after loading, and no measure is required. Alarm indicatorYellow OffNo alarm is generated.The rectifier runs properly, and no measure is required.Steady on The rectifier generates a prewarning for power limiting due to overtemperature. The rectifier generates an alarm for shutdown due to ambient overtemperature protection.Check that the air vent is not blockedand the ambient temperature is within a normal range. The rectifier generates an alarm due to AC input overvoltage or undervoltage protection. Check that the electrical grid voltage is within a normal range. The rectifier is hibernated.No measure is required.Blinking at 0.5 HzThe rectifier communication is interrupted. Replace the rectifier or monitoring module.Fault indicator RedOff The rectifier is not faulty.No measure is required.Steady on The rectifier is locked due to output overvoltage.Pull out the rectifier and reinsert it after 1 minute.There is no output because the rectifier is faulty.Replace the rectifier.•The high -voltage power supply energize equipment. Contacting the high-voltage power supply directly or through a dampened object may cause you to death.•Improper operations on the high-voltage power supply may cause accidents such as fire or electric shock.MaintenanceSuggestions1.Rectify the faults by referring to Table2.2.If you cannot rectify the fault according to Table 2, replace the rectifier.3.Return the faulty rectifier to Huawei for repairing.Huawei technical support website:Base on following suggestion, Simple fault can be dealt with.Table 2 Describes the states of LEDs and the causes for abnormal.DANGERHuawei Technologies Co., Ltd.Huawei Industrial BaseBantian, Longgang, Shenzhen518129。

深圳英士康科技有限公司深圳南山区侨香路美景工业苑2号6楼电话: +86 755 28721662 / 28721663传真: +86 755 84170408E-mail:***************/HID 电子镇流器规格书HID BALLAST SPECIFICATION金属卤素灯模拟调光型EAMH250AD-EUVersion ASHENZHEN EASCA TECHNOLOGIES LIMITEDF6, No.2, MeiJing Industrial Park, QiaoXiang Road, NanShan district, Shenzhen, ChinaTel: +86 755 28721662 28721663 Fax: +86 755 84170408E-mail:***************EAMH250AD-EU ver A ◎技术参数 (Technique Specifications)输入电压:Voltage input range: 170Vac～260Vac开路保护:Protection of open circuit:有Available额定电压:Rating input voltage: 220Vac过热保护:Protection of thermal:有Available输入频率:Input frequency: 50Hz～60Hz触发失败保护:Protection of ignition failure:有Available功率因数: Power factor: > 0.99灯失效保护:Protection of end of lamp life:有Available效率: Efficiency: 95% (Max)重量:Weight:1.8 kg谐波含量: THD < 10%灯管到镇流器最大距离:Max. Lamp distance from ballast :15m输出功率: Output power: 250 W工作温度:Operating temperature range:-40℃～+60℃调光: Dimming: 模拟调光Analog Dimming 0-10v尺寸(L X W X H):Dimension (L X W X H):234.5x102x68.4mm电流波峰因素: Current crest factor: < 1.7最大外壳温度(TC):Max case temperature (TC):85℃输出频率:Output frequency : 100Hz安规标准:Safety and regulation:IEC61347短路保护:Protection of short circuit: 有Available电磁兼容:EMC:EN55015◎ 产品特性 (Product Speciality)◎ 安装图(Mounting Drawing)●进口铝合金外壳，超光氧化处理，具优良散热性●内部采用三防漆处理和特种散热胶灌封，更适于恶劣环境●使用于多种金卤灯光源，如GE，欧斯朗，飞利浦，BLV等及国产多种欧标光源●噪音低，光输出稳定无屏闪现象，具多种自我保护功能●效率高，综合节电30%以上●广泛应用于路桥、广告牌、建筑及景观照明领域●Bright aluminium alloy case with perfect thermal efficiency●Internally double protected by conformal coating and coolingcolloid that ensures ballast work well in various environment●Compliant to most MH lamp brands such as GE, OSRAM,PHILIPS, BLV etc…with EU standard●Low noise, stable lumen output, no flicker, and multipleself-protection functions●High efficiency that saves more than 30%●Applying to road, bridge, billboard, building, sight lighting etc...EAMH250AD-EU version A 说明：1、安装前请仔细阅读本说明。