MSP345中文资料

Thick Film Resistor NetworksSingle-In-Line, Molded SIP; 01, 03, 05 Schematics 6, 8, 9 or 10 Pin “A” Profile and 6, 8 or 10 Pin “C” ProfileFor technical questions, contact: ff2aresistors@Document Number: 31510MSPVishay DaleFEATURES•0.195" [4.95 mm] "A" or 0.350" [8.89 mm] "C"maximum seated height•Thick film resisitive elements•Low temperature coefficient (- 55 °C to + 125 °C)± 100 ppm/°C•Rugged, molded case construction •Reduces total assembly costs•Compatible with automatic insertion equipment and reduces PC board space•Wide resistance range (10 Ω to 2.2 M Ω)•Available in tube pack or side-by-side pack •Lead (Pb)-free version is RoHS compliant* Tighter tracking available** Tolerances in brackets available on requestSTANDARD ELECTRICAL SPECIFICATIONSGLOBAL MODEL/ SCHEMATICPROFILE RESISTOR POWER RATING Max. AT 70 °CW RESISTANCE RANGE ΩSTANDARD TOLERANCE%TEMPERATURE COEFFICIENT (- 55 °C to + 125 °C)ppm/°C TCR TRACKING* (- 55 °C to + 125 °C)ppm/°COPERATINGVOLTAGE Max. VDCMSPxxx01A C 0.20 0.25 10 - 2.2M ± 2 Standard (1, 5)** ± 100 ± 50 ppm/°C 100 MSPxxx03 A C0.30 0.4010 - 2.2M ± 2 Standard (1, 5)** ± 100 ± 50 ppm/°C 100 MSPxxx05A C 0.20 0.2510 - 2.2M± 2 Standard (± 5 %)**± 100± 150 ppm/°C100Document Number: 31510For technical questions, contact: ff2aresistors@MSPThick Film Resistor Networks Single-In-Line, Molded SIP;01, 03, 05 Schematics 6, 8, 9 or 10 Pin "A" Profileand 6, 8 or 10 Pin "C" ProfileVishay DaleDIMENSIONSin inches [millimeters]GLOBAL MODEL A (Max.)B C D (Max.)MSP060.590 [14.99]0.500 [12.70]5MSPxxA = 0.195 [4.95]MSPxxC = 0.350 [8.89]MSP080.790 [20.07]0.700 [17.78]7MSP100.990 [25.15]0.900 [22.86]9MSP090.890 [22.61]0.800 [20.32]80.195 [4.95] ONL YTECCHNICAL SPECIFICATIONSPARAMETERUNITMSP SERIES Package Power RatingMaximum at + 25 °C and + 70 °C See Derating Curves Voltage Coefficient of Resistance V eff < 50 ppm typicalDielectric StrengthVAC 200Isolation Resistance (03 Schematic)Ω> 100M Operating T emperature Range °C - 55 to + 125Storage T emperature Range°C - 55 to + 150MECHANICAL SPECIFICATIONSMarking Resistance to Solvents:Permanency testing per MIL-STD-202, Method 215Solderability:Per MIL-STD-202, Method 208E, RMA flux Body:Molded epoxyT erminals:Copper alloy, solder plated Weight:MSP06A = 0.4 gram MSP06C = 0.7 gram MSP08A = 0.5 gram MSP08C = 0.9 gram MSP09A = 0.55 gram MSP10C = 1.1 gramMSP10A = 0.6 gram For technical questions, contact: ff2aresistors@Document Number: 31510MSPVishay DaleThick Film Resistor Networks Single-In-Line, Molded SIP;01, 03, 05 Schematics 6, 8, 9 or 10 Pin "A" Profileand 6, 8 or 10 Pin "C" ProfileIMPEDANCE CODESCODE R 1(Ω) R 2(Ω)CODE R 1(Ω) R 2(Ω)500B 82130141A 270270750B 120200181A 330390800C 130210191A 330470990A 160260221B 330680101C 180240281B 560560111C 180270381B 560 1.2K 121B 180390501C 620 2.7K 121C 220270102A 1.5K 3.3K 131A220330202B3K6.2KMSPThick Film Resistor Networks Single-In-Line, Molded SIP;01, 03, 05 Schematics 6, 8, 9 or 10 Pin "A" Profileand 6, 8 or 10 Pin "C" ProfileVishay DaleDocument Number: 31510For technical questions, contact: ff2aresistors@Higher power ratings available. Contact factory."A" PROFILE + 70 °C PACKAGE RATINGSMSP10A 1.25 watts MSP09A 1.12 watts MSP08A 1.00 watts MSP06A0.75 watts"C" PROFILE + 70 °C PACKAGE RATINGSMSP10C 1.60 watts MSP08C 1.30 watts MSP06C1.00 wattsPERFORMANCETESTCONDITIONSMAX. ΔR (Typical Test Lots)Power Conditioning 1.5 x rated power, applied 1.5 hours “ON” and 0.5 hour “OFF” for 100 hrs. ± 4 hrs. at + 25 °C ambient temperature ± 0.50 % ΔR Thermal Shock 5 cycles between - 65 °C and + 125 °C ± 0.50 % ΔR Short Time Overload 2.5 x rated working voltage 5 seconds± 0.25 % ΔR Low Temperature Operation 45 minutes at full rated working voltage at - 65 °C ± 0.25 % ΔR Moisture Resistance 240 hrs. with humidity ranging from 80 % RH to 98 % RH± 0.50 % ΔR Resistance to Soldering Heat Leads immersed in + 260 °C solder to within 1/16" of device body for 10 seconds± 0.25 % ΔR Shock T otal of 18 shocks at 100 G's± 0.25 % ΔR Vibration 12 hours at maximum of 20 G's between 10 and 2000 Hz± 0.25 % ΔR Load Life 1000 hrs. at + 70 °C, rated power applied 1.5 hours “ON”, 0.5 hour “OFF” for full 1000 hour period. Derated according to the curve.± 1.00 % ΔR T erminal Strength 4.5 pound pull for 30 seconds ± 0.25 % ΔRInsulation Resistance10 000 Megohm (minimum)-Dielectric Withstanding Voltage-Disclaimer Legal Disclaimer NoticeVishayAll product specifications and data are subject to change without notice.Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product.Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein, which apply to these products.No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay.The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.Product names and markings noted herein may be trademarks of their respective owners.元器件交易网Document Number: 。

2,000 h at 85 °C and full load∆ Capacitance ±20% ESR 200% of limit DCL 100% of limit3,000 h at 85 ºC with rated voltage∆ Capacitance ±10% ESR 200% of limit DCL 100% of limit500 h at 85 °C, capacitance, ESR and DCL, initial requirements10 to 55 Hz, 0.06” and 10 g max, 2 h each planeThe Type 4CMC is the PC-mount version of the high-capacitance Type DCMC screw-terminal capacitor and has about 50% more capacitance per can size through 250 V. It’s for bus filtering applications where more capacitance or smaller can size is important like welders and energy storage. It’s a much better value than a large snap-in capacitor. Its extended cathode foil assures cool operation with heatflow from the capacitor element to the can in all mounting orientations.Highlights• Much better value than large snap-in capacitor • Ripple Currents to > 50 amps at 55 °C • 3-leads for reverse proof, strong mounting • Printed-circuit mounting version of DCMC • Thermal-Pak™ extended cathode constructionSpecificationsOperating Temperature:Rated Voltage:Capacitance:Capacitance Tolerance:DC Leakage Current:Cold Impedance:Ripple Current Multipliers:EIA Ripple Life: Life Test:Shelf Life Test: Vibration: Best Value Printed Circuit Mount TypeFrequency–40 °C to +85 °C 16 to 500 Vdc210 µF to 420,000 µF ± 20%± 20%≤ 6 √CV µA, 6 max, 5 min.–20 °C multiple of 25 °C Z ≤ 8 for 16 to 50 V, 4 for 63 to 100 V, 3 for 160 V & up Ambient Temperature45 °C 55 °C 65 °C 75 °C 85 °C 2.002.001.731.411.0050 Hz 60 Hz 120 Hz 360 Hz 1 kHz 5 kHk-10 kHz & up6.3 to 50 V 0.800.85 1.00 1.05 1.08 1.08 1.0863 to 250 V 0.800.83 1.00 1.15 1.20 1.20 1.20300 to 5000.780.801.001.301.401.401.40Complies with the EU Directive 2002/95/EC requirement restricting the use of Lead (Pb), Mercury (Hg), Cadmium (Cd), Hexavalent chromium (Cr(VI)), PolyBrominated Biphenyls (PBB) and PolyBrominated Diphenyl Ethers (PBDE).Outline DrawingsCase DimensionsPart Numbering System4CMCType 8InsulationAKCase Code100Voltage M Tolerance382Capacitance(blank) = StraightLeads0 = Bare can 8 = PVC and Standoffs9 = Polyester and Standoffs6R3 = 6.3 V 063 = 63 V M = ±20%T = –10% +50% U = –10 +75% 382 = 3800 µF 212 = 2100 µF100 = 100 VCase InchesMillimeters Code D ± .031 L MAX C ± .015 S ± .031 E ± .031 F ± .015 D ± .78 L MAX C ± .78 S ± .78 E ± .78 F ± .38AK 1.375 1.750.500.1750.250.5534.9344.4512.70 4.45 6.3513.97 AA 1.375 2.250.500.1750.250.5534.9357.1512.70 4.45 6.3513.97 AH 1.375 2.750.500.1750.250.5534.9869.8512.70 4.45 6.3513.97 AB 1.375 3.250.500.1750.250.5534.9382.5512.70 4.45 6.3513.97 AJ 1.375 3.750.500.1750.250.5534.9395.2512.70 4.45 6.3513.97 AC 1.375 4.250.500.1750.250.5534.93107.9512.70 4.45 6.3513.97 AD 1.375 4.750.500.1750.250.5534.93120.6512.70 4.45 6.3513.97 AE 1.375 5.250.500.1750.250.5534.93133.3512.70 4.45 6.3513.97 AF 1.375 5.750.500.1750.250.5534.93146.0512.70 4.45 6.3513.97 EA 1.75 2.250.700.3750.350.9044.4557.1517.789.538.8922.86 EH 1.75 2.750.700.3750.350.9044.4569.8517.789.538.8922.86 EB 1.75 3.250.700.3750.350.9044.4582.5517.789.538.8922.86 EJ 1.75 3.750.700.3750.350.9044.4595.2517.789.538.8922.86 EC 1.75 4.250.700.3750.350.9044.45107.9517.789.538.8922.86 ED 1.75 4.750.700.3750.350.9044.45120.6517.789.538.8922.86 EE 1.75 5.250.700.3750.350.9044.45133.3517.789.538.8922.86 EF 1.75 5.750.700.3750.350.9044.45146.0517.789.538.8922.86 BA 2.00 2.250.800.4250.40 1.0050.8057.1520.3210.8010.1625.40 BH 2.00 2.750.800.4250.40 1.0050.8069.8520.3210.8010.1625.40 BB 2.00 3.250.800.4250.40 1.0050.8082.5520.3210.8010.1625.40 BJ 2.00 3.750.800.4250.40 1.0050.8095.2520.3210.8010.1625.40 BC 2.00 4.250.800.4250.40 1.0050.80107.9520.3210.8010.1625.40 BD 2.00 4.750.800.4250.40 1.0050.80120.6520.3210.8010.1625.40 BE 2.00 5.250.800.4250.40 1.0050.80133.2520.3210.8010.1625.40 BF2.005.750.800.4250.401.0050.80146.0520.3210.8010.1625.40RatingsESR Max. 25 ºC 120 Hz 20 kHz (mΩ) (mΩ)Ripple Amps,85 ºC 120 Hz 20 kHz (A) (A)Nominal Size D X L (in)ESR Max. 25 ºC 120 Hz 20 kHz (mΩ) (mΩ)Ripple Amps,85 ºC 120 Hz 20 kHz (A) (A)Nominal Size D X L (in)Cap.(µF)Catalog Part NumberCap.(µF)Catalog Part Number 16 Vdc (20 Vdc Surge)2000004CMC204M016AF8 10.38.216.919.0 1 3/8 X 5 3/4 330004CMC333M016AK8 34.227.2 5.7 6.4 1 3/8 X 1 3/4 2200004CMC224M016EC8 1310.315.217 1 3/4 X 4 1/4 550004CMC553M016AA821.216.98.49.4 1 3/8 X 2 1/4 2400004CMC244M016BJ8 11.79.315.617.5 2 X 3 3/4 770004CMC773M016AH8 18.314.69.310.4 1 3/8 X 2 3/4 2500004CMC254M016ED8 11.59.21719 1 3/4 X 4 3/4 790004CMC793M016EA8 23.018.39.210.4 1 3/4 X 2 1/4 2800004CMC284M016EE8 10.58.418.921.2 1 3/4 X 5 1/4 990004CMC993M016AB814.811.811.112.4 1 3/8 X 3 1/4 2800004CMC284M016BC8 11.49.115.917.8 2 X 4 1/4 1100004CMC114M016EH8 17.413.811.412.7 1 3/4 X 2 3/4 3100004CMC314M016EF8 9.77.721.023.5 1 3/4 X 5 3/4 1200004CMC124M016AJ8 12.810.212.514.0 1 3/8 X 3 3/4 3300004CMC334M016BD8 10.78.516.919 2 X 4 3/4 1200004CMC124M016BA817.714.110.011.2 2 X 2 1/4 3700004CMC374M016BE8 10.08.018.120.3 2 X 5 1/4 1400004CMC144M016AC8 12.59.913.315.0 1 3/8 X 4 1/4 4200004CMC424M016BF89.07.219.822.22 X 5 3/41400004CMC144M016EB815.812.612.914.4 1 3/4 X 3 1/4 25 Vdc (30 Vdc Surge) 1500004CMC154M016BH8 14.511.611.913.3 2 X 2 3/4 220004CMC223M025AK8 63.250.4 4.2 4.7 1 3/8 X 1 3/4 1600004CMC164M016AD8 11.59.114.516.2 1 3/8 X 4 3/4 370004CMC373M025AA8 23.919.17.98.8 1 3/8 X 2 1/4 1800004CMC184M016AE8 10.88.615.817.7 1 3/8 X 5 1/4 520004CMC523M025AH8 20.616.48.89.8 1 3/8 X 2 3/4 1800004CMC184M016EJ8 15.012.013.615.3 1 3/4 X 3 3/4 540004CMC543M025EA8 22.918.39.310.4 1 3/4 X 2 1/4 1900004CMC194M016BB812.39.813.615.22 X3 1/4670004CMC673M025AB816.613.210.511.71 3/8 X 3 1/4Typical Performance CurvesESR Max.25 ºC 120 Hz 20 kHz (mΩ) (mΩ)Ripple Amps,85 ºC120 Hz 20 kHz(A) (A)NominalSizeD X L(in)ESR Max.25 ºC120 Hz 20 kHz(mΩ) (mΩ)Ripple Amps,85 ºC120 Hz 20 kHz(A) (A)NominalSizeD X L(in)Cap. (µF)Catalog PartNumberCap.(µF)Catalog PartNumber780004CMC783M025EH8 19.0015.1010.9012.20 1 3/4 X 2 3/4 50 Vdc (65 Vdc Surge)820004CMC823M025AJ8 14.3011.4011.8013.20 1 3/8 X 3 3/4 100004CMC103M050AK8 44.3035.30 5.00 5.70 1 3/8 X 1 3/4 830004CMC833M025BA8 19.0015.2010.9012.20 2 X 2 1/4 170004CMC173M050AA8 27.3021.807.408.20 1 3/8 X 2 1/4 970004CMC973M025AC8 13.9011.1012.6014.20 1 3/8 X 4 1/4 240004CMC243M050AH8 23.4018.708.209.20 1 3/8 X 2 3/4 1000004CMC104M025BH8 15.5012.4013.0014.60 2 X 2 3/4 270004CMC273M050EA8 28.2022.508.409.40 1 3/4 X 2 1/4 1000004CMC1003M025EB8 17.3013.8012.3013.80 1 3/4 X 3 1/4 310004CMC313M050AB8 18.9015.109.8011.00 1 3/8 X 3 1/4 1100004CMC114M025AD8 12.8010.2013.8015.40 1 3/8 X 4 3/4 330004CMC333M050BA8 27.9022.309.0010.10 2 X 2 1/4 1200004CMC124M025AE8 11.909.5015.0016.80 1 3/8 X 5 1/4 360004CMC363M050EH8 21.2016.9010.3011.50 1 3/4 X 2 3/4 1200004CMC124M025EJ8 16.4013.0013.1014.60 1 3/4 X 3 3/4 380004CMC383M050AJ8 16.2013.0011.1012.40 1 3/8 X 3 3/4 1300004CMC134M025BB8 12.7010.1015.2017.00 2 X 3 1/4 390004CMC393M050EB8 20.3016.2011.3012.70 1 3/4 X 3 1/4 1400004CMC144M025AF8 11.409.1016.1018.00 1 3/8 X 5 3/4 450004CMC453M050AC8 15.7012.5011.9013.30 1 3/8 X 4 1/4 1500004CMC154M025EC8 14.1011.2014.6016.30 1 3/4 X 4 1/4 470004CMC473M050AD8 14.9011.9012.7014.30 1 3/8 X 4 3/4 1600004CMC164M025BJ8 12.5010.0017.1019.20 2 X 3 3/4 470004CMC473M050BH8 19.6015.6011.6013.00 2 X 2 3/4 1700004CMC174M025ED8 12.5010.0016.3018.30 1 3/4 X 4 3/4 480004CMC483M050EJ8 19.2015.3012.1013.50 1 3/4 X 3 3/4 1900004CMC194M025EE8 11.309.0018.2020.40 1 3/4 X 5 1/4 530004CMC533M050AE8 13.9011.0013.9015.60 1 3/8 X 5 1/4 1900004CMC194M025BC8 12.209.7017.4019.50 2 X 4 1/4 560004CMC563M050BB8 16.3013.0013.4015.00 2 X 3 1/4 2100004CMC214M025EF8 10.508.3020.2022.60 1 3/4 X 5 3/4580004CMC583M050EC8 16.5013.1013.5015.10 1 3/4 X 4 1/4 2200004CMC224M025BD8 11.409.1018.6020.80 2 X 4 3/4600004CMC603M050AF8 13.2010.5015.0016.80 1 3/8 X 5 3/4 2500004CMC254M025BE8 10.608.5019.9022.30 2 X 5 1/4670004CMC673M050ED8 14.5011.6015.1017.00 1 3/4 X 4 3/4 2800004CMC284M025BF8 9.607.6021.8024.40 2 X 5 3/4680004CMC683M050BJ8 15.0012.0015.6017.50 2 X 3 3/435 Vdc (40 Vdc Surge) 760004CMC763M050EE8 13.1010.5016.9018.90 1 3/4 X 5 1/4 150004CMC153M035AK8 63.2050.40 4.20 4.70 1 3/8 X 1 3/4820004CMC823M050BC8 14.3011.4016.1018.00 2 X 4 1/4 250004CMC253M035AA8 23.9019.107.908.80 1 3/8 X 2 1/4850004CMC853M050EF8 12.109.6018.8021.10 1 3/4 X 5 3/4 350004CMC353M035AH8 20.6016.408.809.80 1 3/8 X 2 3/4910004CMC913M050BD8 12.7010.1017.6019.80 2 X 4 3/4 380004CMC383M035EA8 22.7018.109.3010.40 1 3/4 X 2 1/41000004CMC104M050BE8 11.809.4019.0021.30 2 X 5 1/4 450004CMC453M035AB8 16.6013.2010.5011.70 1 3/8 X 3 1/41200004CMC124M050BF8 10.508.4020.7023.20 2 X 5 3/4 520004CMC523M035EH8 19.0015.1010.9012.20 1 3/4 X 2 3/463 Vdc (75 Vdc Surge)550004CMC553M035AJ8 14.3011.4011.8013.20 1 3/8 X 3 3/475004CMC752M063AK8 44.1035.10 5.10 5.70 1 3/8 X 1 3/4 560004CMC563M035BA8 19.0015.2010.9012.20 2 X 2 1/4120004CMC123M063AA8 26.8021.407.408.30 1 3/8 X 2 1/4 650004CMC653M035AC8 13.9011.1012.6014.20 1 3/8 X 4 1/4160004CMC163M063EA8 28.2022.508.309.30 1 3/4 X 2 1/4 670004CMC673M035EB8 17.3013.8012.3013.80 1 3/4 X 3 1/4160004CMC163M063AH8 23.5018.808.209.20 1 3/8 X 2 3/4 680004CMC683M035BH8 15.5012.4013.0014.60 2 X 2 3/4210004CMC213M063AB8 18.7014.909.9011.10 1 3/8 X 3 1/4 750004CMC753M035AD8 12.8010.2013.8015.40 1 3/8 X 4 3/4220004CMC223M063EH8 21.2016.9010.3011.50 1 3/4 X 2 3/4 830004CMC833M035EJ8 16.4013.0013.1014.60 1 3/4 X 3 3/4260004CMC263M063AJ8 16.9013.5010.9012.20 1 3/8 X 3 3/4 840004CMC843M035AE8 11.909.5015.2017.10 1 3/8 X 5 1/4260004CMC263M063BA8 27.7022.109.0010.10 2 X 2 1/4 870004CMC873M035BB8 12.7010.1015.2017.00 2 X 3 1/4290004CMC293M063EB8 20.9016.7011.2012.50 1 3/4 X 3 1/4 930004CMC933M035AF8 11.409.1016.1018.10 1 3/8 X 5 3/4300004CMC303M063AC8 17.3013.8011.3012.70 1 3/8 X 4 1/4 1000004CMC104M035EC8 14.1011.2014.6016.30 1 3/4 X 4 1/4330004CMC333M063BH8 19.5015.5011.6013.00 2 X 2 3/4 1100004CMC114M035BJ8 12.5010.0017.1019.20 2 X 3 3/4350004CMC353M063AD8 15.7012.5012.4013.90 1 3/8 X 4 3/4 1100004CMC114M035ED8 12.5010.0016.3018.30 1 3/4 X 4 3/4360004CMC363M063EJ8 20.0016.0011.8013.20 1 3/4 X 3 3/4 1300004CMC134M035EE8 11.309.0018.2020.40 1 3/4 X 5 1/4380004CMC383M063AE8 14.5011.5013.8015.50 1 3/8 X 5 1/4 1300004CMC134M035BC8 12.209.7017.4019.50 2 X 4 1/4430004CMC433M063EC8 17.2013.7013.2014.80 1 3/4 X 4 1/4 1400004CMC144M035EF8 10.508.3020.2022.60 1 3/4 X 5 3/4440004CMC443M063AF8 13.7010.9014.7016.50 1 3/8 X 5 3/4 1500004CMC154M035BD8 11.409.1018.6020.80 2 X 4 3/4470004CMC473M063BB8 16.2012.9013.4015.00 2 X 3 1/4 1700004CMC174M035BE8 10.608.5020.0022.40 2 X 5 1/4500004CMC503M063ED8 15.2012.2014.8016.60 1 3/4 X 4 3/4 1900004CMC194M035BF8 9.607.6021.7024.40 2 X 5 3/4530004CMC533M063BJ8 15.1012.0015.6017.40 2 X 3 3/4570004CMC573M063EE8 13.8011.0016.5018.50 1 3/4 X 5 1/4ESR Max.25 ºC 120 Hz 20 kHz (mΩ) (mΩ)Ripple Amps,85 ºC120 Hz 20 kHz(A) (A)NominalSizeD X L(in)ESR Max.25 ºC120 Hz 20 kHz(mΩ) (mΩ)Ripple Amps,85 ºC120 Hz 20 kHz(A) (A)NominalSizeD X L(in)Cap. (µF)Catalog PartNumberCap.(µF)Catalog PartNumber590004CMC593M063BC8 14.5011.5016.0017.90 2 X 4 1/4220004CMC223M100AF8 20.1016.0012.1013.60 1 3/8 X 5 3/4 640004CMC643M063EF8 12.7010.1018.4020.60 1 3/4 X 5 3/4220004CMC223M100EC8 21.9017.5011.7013.10 1 3/4 X 4 1/4 690004CMC693M063BD8 12.8010.2017.6019.70 2 X 4 3/4260004CMC263M100ED8 19.3015.4013.2014.70 1 3/4 X 4 3/4 790004CMC793M063BE8 11.609.2019.1021.40 2 X 5 1/4260004CMC263M100BJ8 23.6018.8012.5013.90 2 X 3 3/4 890004CMC893M063BF8 10.708.5020.6023.10 2 X 5 3/4300004CMC303M100EE8 17.3013.8014.7016.50 1 3/4 X 5 1/480 Vdc (100 Vdc Surge) 300004CMC303M100BC8 20.2016.1013.5015.20 2 X 4 1/4 56004CMC562M080AK8 59.6047.50 4.40 4.90 1 3/8 X 1 3/4330004CMC333M100EF8 15.8012.6016.4018.40 1 3/4 X 5 3/4 85004CMC852M080AA8 36.2028.80 6.407.20 1 3/8 X 2 1/4350004CMC353M100BD8 17.8014.2014.9016.70 2 X 4 3/4 120004CMC123M080EA8 38.4030.607.208.00 1 3/4 X 2 1/4400004CMC403M100BE8 16.1012.8016.3018.20 2 X 5 1/4 120004CMC123M080AH8 31.5025.107.107.90 1 3/8 X 2 3/4450004CMC453M100BF8 14.7011.7017.5019.60 2 X 5 3/4 150004CMC153M080AB8 31.6025.207.608.50 1 3/8 X 3 1/4160 Vdc (200 Vdc Surge)170004CMC173M080EH8 34.0027.108.109.10 1 3/4 X 2 3/415004CMC152M160AK8 81.7065.20 3.70 4.20 1 3/8 X 1 3/4 180004CMC183M080BA8 32.8026.108.309.30 2 X 2 1/425004CMC252M160AA8 51.8041.30 5.30 6.00 1 3/8 X 2 1/4 190004CMC193M080AJ8 25.2020.108.9010.00 1 3/8 X 3 3/435004CMC352M160AH8 37.5029.90 6.507.30 1 3/8 X 2 3/4 220004CMC223M080AC8 20.9016.7010.3011.50 1 3/8 X 4 1/437004CMC372M160EA8 47.1037.50 6.10 6.90 1 3/4 X 2 1/4 220004CMC223M080EB8 30.5024.309.3010.40 1 3/4 X 3 1/445004CMC452M160AB8 29.6023.607.808.80 1 3/8 X 3 1/4 230004CMC233M080BH8 23.1018.4010.7011.90 2 X 2 3/448004CMC482M160BA8 35.4028.207.208.10 2 X 2 1/4 260004CMC263M080AD8 19.1015.2011.2012.60 1 3/8 X 4 3/452004CMC522M160EH8 29.0023.108.309.30 1 3/4 X 2 3/4 270004CMC273M080EJ8 25.1020.0010.5011.80 1 3/4 X 3 3/455004CMC552M160AJ8 23.5018.7029.3032.80 1 3/8 X 3 3/4 290004CMC293M080AE8 17.7014.1012.5014.00 1 3/8 X 5 1/466004CMC662M160AC8 20.2016.1010.5011.70 1 3/8 X 4 1/4 300004CMC303M080BB8 19.2015.3012.3013.80 2 X 3 1/468004CMC682M160EB8 22.5017.9010.2011.50 1 3/4 X 3 1/4 320004CMC323M080AF8 16.7013.3013.3014.90 1 3/8 X 5 3/471004CMC712M160AD8 18.6014.8011.4012.80 1 3/8 X 4 3/4 320004CMC323M080EC8 21.5017.1011.8013.20 1 3/4 X 4 1/471004CMC712M160BH8 26.5021.209.0010.10 2 X 2 3/4 370004CMC373M080BJ8 18.0014.3014.3016.00 2 X 3 3/480004CMC802M160AE8 16.8013.4012.6014.20 1 3/8 X 5 1/4 370004CMC373M080ED8 18.9015.1013.3014.90 1 3/4 X 4 3/483004CMC832M160EJ8 18.5014.7011.7013.10 1 3/4 X 3 3/4 430004CMC433M080BC8 15.9012.6015.3017.10 2 X 4 1/490004CMC902M160AF8 19.2015.3012.4013.90 1 3/8 X 5 3/4 430004CMC433M080EE8 17.0013.6014.8016.60 1 3/4 X 5 1/493004CMC932M160BB8 20.6016.4010.8012.10 2 X 3 1/4 480004CMC483M080EF8 15.6012.4016.6018.60 1 3/4 X 5 3/4100004CMC1002M160EC8 15.8012.6013.1014.60 1 3/4 X 4 1/4 500004CMC503M080BD8 13.6010.8017.1019.10 2 X 4 3/4110004CMC113M160BJ8 16.9013.5013.3014.90 2 X 3 3/4 580004CMC583M080BE8 12.209.7018.6020.90 2 X 5 1/4120004CMC123M160ED8 13.9011.1014.7016.50 1 3/4 X 4 3/4 650004CMC653M080BF8 11.208.9020.1022.50 2 X 5 3/4130004CMC133M160EE8 12.509.9016.5018.40 1 3/4 X 5 1/4 100 Vdc (125 Vdc Surge) 130004CMC133M160BC8 14.5011.6014.5016.20 2 X 4 1/4 38004CMC382M100AK8 58.6046.70 4.40 4.90 1 3/8 X 1 3/4150004CMC153M160EF8 11.409.1018.4020.60 1 3/4 X 5 3/4 63004CMC632M100AA8 35.6028.30 6.507.20 1 3/8 X 2 1/4160004CMC163M160BD8 12.8010.2015.9017.80 2 X 4 3/4 81004CMC812M100AH8 32.8026.20 2.20 2.50 1 3/8 X 2 3/4180004CMC183M160BE8 11.509.2017.4019.50 2 X 5 1/4 82004CMC822M100EA8 39.2031.207.107.90 1 3/4 X 2 1/4200004CMC203M160BF8 10.508.4018.8021.00 2 X 5 3/4 100004CMC103M100AB8 32.9026.207.408.30 1 3/8 X 3 1/4200 Vdc (250 Vdc Surge)110004CMC113M100BA8 35.9028.707.908.90 2 X 2 1/412004CMC122M200AK8 105.2060.40 3.10 4.10 1 3/8 X 1 3/4 120004CMC123M100EH8 34.7027.708.009.00 1 3/4 X 2 3/419004CMC192M200AA8 66.6038.20 4.50 5.90 1 3/8 X 2 1/4 130004CMC133M100AJ8 31.7025.307.908.90 1 3/8 X 3 3/427004CMC272M200AH8 48.0027.60 5.407.20 1 3/8 X 2 3/4 150004CMC153M100EB8 31.1024.809.2010.30 1 3/4 X 3 1/427004CMC272M200EA8 60.0034.40 5.307.00 1 3/4 X 2 1/4 150004CMC153M100AC8 27.4021.800.90 1.10 1 3/8 X 4 1/435004CMC352M200AB8 37.8021.70 6.608.70 1 3/8 X 3 1/4 160004CMC163M100BH8 26.4021.0010.0011.20 2 X 2 3/435004CMC352M200BA8 44.2030.70 6.607.90 2 X 2 1/4 170004CMC173M100AD8 24.2019.3010.0011.20 1 3/8 X 4 3/437004CMC372M200EH8 38.1021.90 6.909.10 1 3/4 X 2 3/4 190004CMC193M100EJ8 25.6020.4010.4011.70 1 3/4 X 3 3/443004CMC432M200AJ8 29.9017.207.8010.20 1 3/8 X 3 3/4 200004CMC203M100AE8 21.9017.5011.2012.60 1 3/8 X 5 1/448004CMC482M200EB8 29.4016.908.5011.20 1 3/4 X 3 1/4 210004CMC213M100BB8 22.9018.3011.3012.60 2 X 3 1/450004CMC502M200BH8 33.1023.008.209.80 2 X 2 3/4ESR Max.25 ºC 120 Hz 20 kHz (mΩ) (mΩ)Ripple Amps,85 ºC120 Hz 20 kHz(A) (A)NominalSizeD X L(in)ESR Max.25 ºC120 Hz 20 kHz(mΩ) (mΩ)Ripple Amps,85 ºC120 Hz 20 kHz(A) (A)NominalSizeD X L(in)Cap. (µF)Catalog PartNumberCap.(µF)Catalog PartNumber51004CMC512M200AC8 25.7014.708.8011.70 1 3/8 X 4 1/416004CMC162M300AB8 82.7047.50 4.80 6.30 1 3/8 X 3 1/4 58004CMC582M200AD8 22.6013.009.8012.90 1 3/8 X 4 3/418004CMC182M300EH8 99.2056.90 4.80 6.30 1 3/4 X 2 3/4 59004CMC592M200EJ8 24.1013.809.7012.70 1 3/4 X 3 3/419004CMC192M300AJ8 68.0039.00 5.607.40 1 3/8 X 3 3/4 66004CMC662M200AE8 20.3011.6010.9014.40 1 3/8 X 5 1/422004CMC222M300BH8 67.1037.40 6.308.40 2 X 2 3/4 68004CMC682M200BB8 25.6017.809.8011.80 2 X 3 1/423004CMC232M300AC8 57.9033.20 6.408.40 1 3/8 X 4 1/4 71004CMC712M200EC8 20.5011.8010.8014.30 1 3/4 X 4 1/423004CMC232M300EB8 76.1043.70 5.807.70 1 3/4 X 3 1/4 74004CMC742M200AF8 23.1013.3010.7014.20 1 3/8 X 5 3/426004CMC262M300AD8 50.6029.007.109.40 1 3/8 X 4 3/4 81004CMC812M200BJ8 21.0014.6012.2014.60 2 X 3 3/429004CMC292M300AE8 45.0025.807.8010.30 1 3/8 X 5 1/4 82004CMC822M200ED8 17.9010.3012.2016.10 1 3/4 X 4 3/429004CMC292M300BB8 51.6028.707.6010.20 2 X 3 1/4 93004CMC932M200EE8 16.009.2013.7018.10 1 3/4 X 5 1/429004CMC292M300EJ8 61.9035.50 6.808.90 1 3/4 X 3 3/4 95004CMC952M200BC8 19.1013.3012.8015.40 2 X 4 1/433004CMC332M300AF8 50.7029.107.6010.10 1 3/8 X 5 3/4 100004CMC103M200EF8 14.508.3015.4020.30 1 3/4 X 5 3/435004CMC352M300EC8 52.2030.007.7010.20 1 3/4 X 4 1/4 110004CMC113M200BD8 15.7010.9014.6017.50 2 X 4 3/436004CMC362M300BJ8 51.2028.508.1010.80 2 X 3 3/4 120004CMC123M200BE8 14.109.8016.0019.20 2 X 5 1/440004CMC402M300ED8 45.3026.008.6011.40 1 3/4 X 4 3/4 140004CMC143M200BF8 12.808.9017.3020.80 2 X 5 3/443004CMC432M300BC8 43.3024.109.2012.30 2 X 4 1/4 250 Vdc (300 Vdc Surge)46004CMC462M300EE8 40.1023.009.5012.60 1 3/4 X 5 1/4 8904CMC891M250AK8 137.0078.60 2.60 3.40 1 3/8 X 1 3/449004CMC492M300BD8 38.0021.2010.2013.70 2 X 4 3/4 15004CMC152M250AA8 86.5049.70 3.70 4.90 1 3/8 X 2 1/451004CMC512M300EF8 36.0020.6010.4013.70 1 3/4 X 5 3/4 19004CMC192M250EA8 68.7039.40 4.80 6.30 1 3/4 X 2 1/457004CMC572M300BE8 33.3018.5011.3015.10 2 X 5 1/4 21004CMC212M250AH8 62.3035.70 4.50 6.00 1 3/8 X 2 3/464004CMC642M300BF8 29.9016.7012.3016.50 2 X 5 3/4 27004CMC272M250BA8 54.2037.60 5.807.00 2 X 2 1/4350 Vdc (400 Vdc Surge)27004CMC272M250AB8 48.8028.00 5.507.20 1 3/8 X 3 1/44304CMC431M350AK8 264.10151.60 2.10 2.80 1 3/8 X 1 3/4 28004CMC282M250EH8 47.8027.40 6.108.10 1 3/4 X 2 3/47104CMC711M350AA8 158.9091.20 3.10 4.00 1 3/8 X 2 1/4 32004CMC322M250AJ8 38.6022.10 6.508.50 1 3/8 X 3 3/410004CMC102M350EA8 119.2068.40 4.10 5.40 1 3/4 X 2 1/4 37004CMC372M250EB8 36.8021.107.6010.00 1 3/4 X 3 1/410004CMC102M350AH8 113.9065.40 3.70 4.90 1 3/8 X 2 3/4 38004CMC382M250BH8 40.5028.107.208.70 2 X 2 3/412004CMC122M350BA8 98.1054.60 4.80 6.40 2 X 2 1/4 39004CMC392M250AC8 33.0018.907.409.70 1 3/8 X 4 1/413004CMC132M350EH8 105.1060.30 4.60 6.10 1 3/4 X 2 3/4 44004CMC442M250AD8 29.0016.608.2010.80 1 3/8 X 4 3/413004CMC132M350AB8 89.0051.10 4.50 6.00 1 3/8 X 3 1/4 45004CMC452M250EJ8 30.1017.308.6011.40 1 3/4 X 3 3/416004CMC162M350BH8 71.8040.00 6.008.10 2 X 2 3/4 50004CMC502M250AE8 25.9014.909.1012.00 1 3/8 X 5 1/416004CMC162M350AJ8 73.2042.00 5.20 6.90 1 3/8 X 3 3/4 50004CMC502M250BB8 31.2021.708.7010.40 2 X 3 1/417004CMC172M350EB8 80.6046.30 5.707.50 1 3/4 X 3 1/4 54004CMC542M250EC8 25.5014.709.7012.80 1 3/4 X 4 1/418004CMC182M350AC8 62.3035.80 6.007.90 1 3/8 X 4 1/4 56004CMC562M250AF8 29.4016.909.0011.90 1 3/8 X 5 3/421004CMC212M350BB8 55.1030.707.309.70 2 X 3 1/4 62004CMC622M250BJ8 25.5017.7010.7012.90 2 X 3 3/421004CMC212M350AD8 54.4031.20 6.708.80 1 3/8 X 4 3/4 63004CMC632M250ED8 22.3012.8011.0014.50 1 3/4 X 4 3/421004CMC212M350EJ8 65.5037.60 6.508.60 1 3/4 X 3 3/4 72004CMC722M250EE8 19.8011.4012.3016.30 1 3/4 X 5 1/424004CMC242M350AE8 48.3027.707.409.80 1 3/8 X 5 1/4 73004CMC732M250BC8 21.7015.1011.7014.00 2 X 4 1/425004CMC252M350EC8 55.3031.707.409.70 1 3/4 X 4 1/4 81004CMC812M250EF8 18.0010.3013.8018.30 1 3/4 X 5 3/426004CMC262M350BJ8 47.9026.708.7011.70 2 X 3 3/4 85004CMC852M250BD8 19.0013.2012.9015.50 2 X 4 3/427004CMC272M350AF8 54.5031.307.409.70 1 3/8 X 5 3/4 97004CMC972M250BE8 17.0011.8014.2017.00 2 X 5 1/429004CMC292M350ED8 47.9027.508.3011.00 1 3/4 X 4 3/4 110004CMC113M250BF8 15.4010.7015.4018.40 2 X 5 3/431004CMC312M350BC8 45.7025.509.0012.10 2 X 4 1/4 300 Vdc (350 Vdc Surge) 33004CMC332M350EE8 42.4024.309.4012.40 1 3/4 X 5 1/4 5204CMC521M300AK8 245.00141.00 2.20 2.90 1 3/8 X 1 3/436004CMC362M350BD8 40.1022.409.9013.30 2 X 4 3/4 8704CMC871M300AA8 148.0084.70 3.10 4.10 1 3/8 X 2 1/437004CMC372M350EF8 38.0021.8010.6014.00 1 3/4 X 5 3/4 12004CMC122M300AH8 106.0060.70 4.00 5.30 1 3/8 X 2 3/442004CMC422M350BE8 35.1019.6011.0014.70 2 X 5 1/4 13004CMC132M300EA8 111.0063.80 4.20 5.50 1 3/4 X 2 1/447004CMC472M350BF8 31.6017.6012.0016.00 2 X 5 3/4 16004CMC162M300BA8 93.2051.90 5.00 6.70 2 X 2 1/4ESR Max.25 ºC 120 Hz 20 kHz (mΩ) (mΩ)Ripple Amps,85 ºC120 Hz 20 kHz(A) (A)NominalSizeD X L(in)ESR Max.25 ºC120 Hz 20 kHz(mΩ) (mΩ)Ripple Amps,85 ºC120 Hz 20 kHz(A) (A)NominalSizeD X L(in)Cap. (µF)Catalog PartNumberCap.(µF)Catalog PartNumber400 Vdc (450 Vdc Surge) 15004CMC152M450BB8 75.9042.20 5.807.80 2 X 3 1/43204CMC321M400AK2B 382.00195.00 1.70 2.40 1 3/8 X 1 3/415004CMC152M450AE8 61.8031.50 5.708.00 1 3/8 X 5 1/4 5904CMC591M400AA2B 212.00108.00 2.60 3.70 1 3/8 X 2 1/415004CMC152M450EJ8 75.1038.30 5.708.00 1 3/4 X 3 3/4 8004CMC801M400AH2B 156.0079.40 3.20 4.50 1 3/8 X 2 3/416004CMC162M450AF8 69.3035.40 5.708.00 1 3/8 X 5 3/4 8404CMC841M400EA8 154.0078.80 3.60 5.00 1 3/4 X 2 1/418004CMC182M450EC8 63.3032.30 6.509.10 1 3/4 X 4 1/4 10004CMC102M400BA8 130.0072.20 4.20 5.60 2 X 2 1/419004CMC192M450BJ8 61.7034.307.209.70 2 X 3 3/4 10004CMC102M400AB2B 119.0060.90 3.90 5.50 1 3/8 X 3 1/421004CMC212M450ED8 54.8028.007.3010.30 1 3/4 X 4 3/4 12004CMC122M400EH8 107.0054.60 4.60 6.40 1 3/4 X 2 3/422004CMC222M450BC8 52.1029.007.9010.60 2 X 4 1/4 13004CMC132M400AJ2B 96.9049.50 4.50 6.40 1 3/8 X 3 3/423004CMC232M450EE8 48.4024.708.3011.60 1 3/4 X 5 1/4 14004CMC142M400BH8 93.6052.10 5.307.10 2 X 2 3/426004CMC262M450EF8 43.5022.209.3013.00 1 3/4 X 5 3/4 15004CMC152M400EB8 87.4044.60 5.507.70 1 3/4 X 3 1/426004CMC262M450BD8 45.7025.408.7011.70 2 X 4 3/4 15004CMC152M400AC2B 81.8041.700.500.80 1 3/8 X 4 1/431004CMC312M450BE8 38.8021.609.8013.10 2 X 5 1/4 16004CMC162M400AD2B 78.6040.10 5.507.80 1 3/8 X 4 3/434004CMC342M450BF8 35.0019.5010.7014.30 2 X 5 3/4 18004CMC182M400EJ8 71.0036.20 6.308.80 1 3/4 X 3 3/4500 Vdc (550 Vdc Surge)18004CMC182M400AE2B 69.5035.40 6.208.70 1 3/8 X 5 1/42104CMC211M500AK8 487.00287.00 1.50 2.10 1 3/8 X 1 3/4 19004CMC192M400BB8 71.9040.00 6.408.50 2 X 3 1/43104CMC311M500AA8 325.00191.00 2.10 3.00 1 3/8 X 2 1/4 20004CMC202M400AF2B 77.9039.70 6.208.60 1 3/8 X 5 3/44404CMC441M500EA8 238.00140.00 2.90 4.00 1 3/4 X 2 1/4 21004CMC212M400EC8 59.9030.507.109.90 1 3/4 X 4 1/44504CMC451M500AH8 225.00133.00 2.60 3.70 1 3/8 X 2 3/4 23004CMC232M400BJ8 58.4032.507.9010.60 2 X 3 3/45604CMC561M500BA8 193.00114.00 3.40 4.60 2 X 2 1/4 25004CMC252M400ED8 51.9026.508.0011.20 1 3/4 X 4 3/45904CMC591M500AB8 173.00102.00 3.20 4.50 1 3/8 X 3 1/4 27004CMC272M400BC8 49.3027.508.7011.60 2 X 4 1/46304CMC631M500EH8 165.0097.20 3.70 5.20 1 3/4 X 2 3/4 29004CMC292M400EE8 45.8023.409.0012.70 1 3/4 X 5 1/47304CMC731M500AJ8 140.0082.60 3.80 5.30 1 3/8 X 3 3/4 32004CMC322M400EF8 41.1021.0010.2014.30 1 3/4 X 5 3/47804CMC781M500BH8 134.0078.70 4.40 5.90 2 X 2 3/4 32004CMC322M400BD8 42.8023.809.6012.90 2 X 4 3/48204CMC821M500EB8 126.0074.40 4.50 6.40 1 3/4 X 3 1/4 36004CMC362M400BE8 37.9021.1010.6014.20 2 X 5 1/48204CMC821M500AC8 125.0073.60 4.20 5.90 1 3/8 X 4 1/4 41004CMC412M400BF8 34.0018.9011.5015.40 2 X 5 3/49004CMC901M500AD8 113.0066.40 4.60 6.50 1 3/8 X 4 3/4 450 Vdc (500 Vdc Surge) 10004CMC102M500BB8 103.0060.30 5.307.10 2 X 3 1/4 3304CMC331M450AK8 281.00143.00 1.80 2.50 1 3/8 X 1 3/410004CMC102M500AE8 99.0058.50 5.207.30 1 3/8 X 5 1/4 4904CMC491M450AA8 188.0095.70 2.50 3.40 1 3/8 X 2 1/410004CMC102M500EJ8 103.0060.40 5.207.30 1 3/4 X 3 3/4 6004CMC601M450AH8 138.0070.40 3.00 4.10 1 3/8 X 2 3/411004CMC112M500AF8 114.0067.30 5.107.10 1 3/8 X 5 3/4 6904CMC691M450EA8 163.0083.30 3.30 4.60 1 3/4 X 2 1/412004CMC122M500EC8 86.4050.90 5.908.30 1 3/4 X 4 1/4 8604CMC861M450BA8 116.0064.80 4.10 5.60 2 X 2 1/413004CMC132M500BJ8 83.2049.00 6.608.90 2 X 3 3/4 8604CMC861M450AB8 106.0054.00 3.60 5.10 1 3/8 X 3 1/414004CMC142M500ED8 74.8044.00 6.709.40 1 3/4 X 4 3/4 9304CMC931M450EH8 121.0061.50 4.10 5.70 1 3/4 X 2 3/415004CMC152M500BC8 70.2041.307.309.70 2 X 4 1/4 10004CMC102M450AJ8 86.1043.90 4.20 5.90 1 3/8 X 3 3/416004CMC162M500EE8 66.0038.807.5010.60 1 3/4 X 5 1/4 11004CMC112M450BH8 98.9055.10 4.80 6.50 2 X 2 3/418004CMC182M500EF8 59.1034.808.5011.90 1 3/4 X 5 3/4 12004CMC122M450EB8 92.4047.10 5.007.00 1 3/4 X 3 1/418004CMC182M500BD8 60.7035.808.1010.80 2 X 4 3/4 12004CMC122M450AC8 72.7037.10 4.80 6.80 1 3/8 X 4 1/421004CMC212M500BE8 52.1030.709.0012.10 2 X 5 1/4 13004CMC132M450AD8 69.9035.70 5.107.20 1 3/8 X 4 3/423004CMC232M500BF8 46.9027.609.8013.20 2 X 5 3/4。

TE3-LIU™Line Interface Unit for DS3,STS1and E3 PEF 3452, Version 1.3ABM®, ACE®, AOP®, ARCOFI®, ASM®, ASP®, DigiTape®, DuSLIC®, EPIC®, ELIC®, FALC®, GEMINAX®, IDEC®, INCA®, IOM®, IPAT®-2, ISAC®, ITAC®, IWE®, IWORX®, MUSAC®, MuSLIC®, OCTAT®, OptiPort®, POTSWIRE®, QUAT®, QuadFALC®, SCOUT®, SICAT®, SICOFI®, SIDEC®, SLICOFI®, SMINT®, SOCRATES®, VINETIC®, 10BaseV®, 10BaseVX® are registered trademarks of Infineon Technologies AG. 10BaseS™, EasyPort™, VDSLite™are trademarks of Infineon Technologies AG. Microsoft® is a registered trademark of Microsoft Corporation, Linux® of Linus Torvalds, Visio® of Visio Corporation, and FrameMaker® of Adobe Systems Incorporated.The information in this document is subject to change without notice.Edition 2005-01-24Published by Infineon Technologies AG,St.-Martin-Strasse 53,81669 München, Germany© Infineon Technologies AG 1/24/05.All Rights Reserved.Attention please!The information herein is given to describe certain components and shall not be considered as a guarantee of characteristics.Terms of delivery and rights to technical change reserved.We hereby disclaim any and all warranties, including but not limited to warranties of non-infringement, regarding circuits, descriptions and charts stated herein.InformationFor further information on technology, delivery terms and conditions and prices please contact your nearest Infineon Technologies Office ().WarningsDue to technical requirements components may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies Office.Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system, or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons mayTE3-LIU™Revision History:2005-01-24Rev. 2 Previous Version:Preliminary Data Sheet TE3-LIU V1.3, 2001-12-05, DS1 Page Subjects (major changes since last revision)Page49Table17Table of Contents PagePreface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 1.1Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 1.2Logic Symbol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 1.3Typical Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 2.1Pin Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 2.2Pin Definitions and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 3.1Functional Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 3.2Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 3.3Functional Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 3.3.1Hardware Control Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 4Interface Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 4.1Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 4.1.1Standard Receiver Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 4.1.2Line Monitoring Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 4.1.3Receive Line Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 4.1.4Receive Clock and Data Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 4.1.5Receive Line Coding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 4.1.5.1AMI Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 4.1.5.2B3ZS Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 4.1.5.3HDB3 Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 4.1.6Alarm Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 4.1.6.1DS3 LOS Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 4.1.6.2STS-1 LOS Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 4.1.6.3E3 LOS Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 4.1.7Jitter Tolerance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 4.1.8Receive Output Jitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 4.2Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 4.2.1Transmit Line Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 4.2.2Transmit Clock System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 4.2.3Jitter Attenuation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 4.2.4Intrinsic Jitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 4.2.5Pulse Shaper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 4.2.6Transmit Line Coding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 4.2.6.1AMI Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 4.2.6.2B3ZS Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 4.2.6.3HDB3 Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 4.2.7AIS Insertion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43Table of Contents Page4.3Framer Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 4.4Maintenance Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 4.4.1Remote Loop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 4.4.2Local Loop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 455Operational Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 5.1Operational Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 5.2Device Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 5.3Device Power Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 5.4Transmit Line Inactive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 6Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 6.1Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 6.2Operating Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 6.3DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 6.4AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 6.4.1Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 6.4.2Reference Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 6.4.3Jitter Attenuator Reference Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 6.4.4Microprocessor Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 6.4.5Transmit Input Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 6.4.6Receive Output Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 6.4.7Pulse Templates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 6.4.7.1Pulse Template E3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 6.4.7.2Pulse Template DS3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 6.4.7.3Pulse Template STS-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 6.5Capacitances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 6.6Package Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 6.7Test Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 7Package Outlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 8Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 8.1Cable Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 8.2Application Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68List of Figures Page Figure1Logic Symbol. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Figure2T3/T1 Multiplexer Application. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Figure3Channelized T3 Link Layer Application . . . . . . . . . . . . . . . . . . . . . . . . 14 Figure4Unchannelized T3 Link Layer Application . . . . . . . . . . . . . . . . . . . . . . 14 Figure5Pin Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Figure6Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Figure7Receiver Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Figure8DS3 Line Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Figure9Receive Clock System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Figure10E3 Loss of Signal Definition. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Figure11Jitter Tolerance Principle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Figure12Jitter Tolerance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Figure13Transmitter Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Figure14Transmit Clock System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Figure15Jitter Attenuation Characteristic. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Figure16Remote Loop Signal Flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Figure17Local Loop Signal Flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Figure18Reset Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Figure19Reference Clock Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Figure20XTAL Clock Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Figure21Recommended Crystal Circuit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Figure22Crystal Pulling Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Figure23Chip Select Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Figure24XCLK Input Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Figure25RCLK Output Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Figure26E3 Pulse Shape at Transmitter Output . . . . . . . . . . . . . . . . . . . . . . . . 58 Figure27DS3 Pulse Shape at the Cross Connect Point (450 ft.). . . . . . . . . . . . 59 Figure28STS-1 Pulse Shape at the Cross Connect Point (450 ft.) . . . . . . . . . . 61 Figure29Thermal Behavior of Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 Figure30Input/Output Waveforms for AC Testing . . . . . . . . . . . . . . . . . . . . . . . 64 Figure31DS3 Cable Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Figure32Application Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67List of Tables Page Table1Interface Pin Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Table2Control Pin Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Table3Power Supply Pins. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Table4Test Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Table5Hardware Control Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Table6Hardware Indication Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Table7External Component Values for Receiver . . . . . . . . . . . . . . . . . . . . . . 30 Table8External Component Values for DS Line Monitoring. . . . . . . . . . . . . . 31 Table9E3 Receive Return Loss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Table10Input Jitter Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Table11External Component Values for Transmitter . . . . . . . . . . . . . . . . . . . . 38 Table12E3 Transmit Return Loss. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Table13Jitter Attenuation PLL Operation Frequencies. . . . . . . . . . . . . . . . . . . 40 Table14Transmit Output Jitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Table15Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Table16Power Supply Range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Table17DC Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Table18Reset Timing Parameter Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Table19REFCLK Timing Parameter Values. . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Table20XTAL Timing Parameter Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Table21XTAL Crystal Parameter Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Table22Chip Select Timing Parameter Values. . . . . . . . . . . . . . . . . . . . . . . . . 55 Table23XCLK Timing Parameter Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Table24RCLK Timing Parameter Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Table25E3 Pulse Mask. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Table26DS3 Pulse Mask (ANSI T1.404, GR-499-CORE) . . . . . . . . . . . . . . . . 59 Table27DS3 Pulse Mask (ANSI T1.404) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Table28DS3 Pulse Mask (GR-499-CORE). . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Table29STS-1 Pulse Mask. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Table30STS-1 Pulse Mask (ANSI T1.102). . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Table31Pin Capacitances. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 Table32Package Characteristic Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 Table33AC Test Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64PrefaceThe PEF 3452 (TE3-LIU™) is a flexible line interface unit for a wide area of telecommunication and data communication applications. The device is addressed to fulfill all requirements to build a DS3, STS-1 or E3 line interface.Organization of this DocumentThis Data Sheet is organized as follows:•OverviewGives a general description of the product, lists the key features, and presents some typical applications.•Pin DescriptionsLists pin locations with associated signals, categorizes signals according to function, and describes signals.•Functional DescriptionDescribes the functional blocks and principle operation modes.•Interface DescriptionDescribes the device interfaces.•Operational DescriptionShows the operation modes and how their initialization.•Electrical CharacteristicsSpecifies maximum ratings, DC and AC characteristics.•Package OutlinesShows the mechanical values of the device package.•Appendix•IndexRelated DocumentationThis document refers to the following international standards(in alphabetical/numerical order):ACA TS016 (general requirements for Australia)CTR-24/TBR-24 (E3 requirements)ETS 300 166 (E3 transmit return loss)ITU-T G.703 (E3 pulse mask, B3ZS/HDB3 code, E3 receive return loss)ITU-T G.751 (jitter requirements E3)ITU-T G.775 (loss of signal definition)ITU-T G.823 (jitter requirements E3)ITU-T G.824 (jitter requirements DS3)ITU-T O.151 (pseudo random binary sequence (PRBS) definition)GR-253-CORE (STS-1 jitter requirements)GR-499-CORE (DS3 pulse mask, DS3 jitter requirements)ANSI T1.102 (STS-1 pulse mask)ANSI T1.102 Annex B (DS3 monitoring)ANSI T1.231 (maintenance functions, defect definitions)ANSI T1.404 (DS3 pulse mask)MIL-STD 883D (ESD requirements)Your CommentsWe welcome your comments on this document. We are continuously trying improving our documentation. Please send your remarks and suggestions by e-mail tocom.docu_comments@Please provide in the subject of your e-mail:device name (TE3-LIU™), device number (PEF 3452), device version (Version 1.3), and in the body of your e-mail:document type (Data Sheet), issue date (2005-01-24) and document revision number (Rev. 2).Overview 1OverviewThe TE3-LIU™ PEF 3452 Line Interface Unit is used to connect a DS3/STS-1 or E3 framer device to an analog transmission line. The line interface fulfills the relevant standards for DS3 (44.736 Mbit/s), STS-1 (51.840 Mbit/s) and E3 (34.368 Mbit/s) systems.The TE3-LIU™ comes in a P-MQFP-44-2 package (SMD) to save a significant amount of board space. The integrated jitter attenuation further reduces overall system complexity and cost.This CMOS 3.3V low power device contains an integrated pulse shaper to drive any line length within the range of up to 1100ft. without the need for external length selection (Line Build Out).The hardware configuration mode allows low cost systems with flexible device setting without the need for a microprocessor.An optional microprocessor mode allows the connection to a standard microprocessor bus to control hardware settings.Type Package PEF 3452P-MQFP-44-2Line Interface Unit for DS3,STS1and E3TE3-LIU™PEF 3452Version 1.31.1Features•Generic analog interface for all DS3/STS-1/E3applications•Single chip solution for receive and transmit direction • 3.3V low power device•Integrated receive equalization network •Integrated noise and crosstalk filter•Clock and data recovery using an integrated PLL with ultra-low intrinsic jitter•Transmit clock duty cycle correction PLL•No external components required for clock and data recovery and receive equalizer•DSX receive line monitor (additional 20dB gain according to ANSI T1.102)•Low transmitter output impedances for high transmit return loss •Disable function of the analog transmit line outputs•Transmit pulse shaper to fulfill requirements of ANSI T1.404,Telcordia GR-499-CORE, ANSI T1.102 and ITU-T G.703 (E3)•Maximum line length up to 1100 ft. (using standard coaxial cable, for example AT&T 728A, 734A or 734D)•External line length selection (LBO) is not required•Jitter specifications of GR-499-CORE and ITU-T G.823 are met •Integrated jitter attenuation PLL and buffer in transmit direction•Dual or single rail digital inputs and outputs from/to the framer interface •Selectable line codes (HDB3 (E3), B3ZS (DS3/STS-1), AMI)•Analog and digital loss of signal detection and indication •Automatic RDOP/RDON blanking option in case of LOS •Bipolar violation indication•Local loop and remote loop for diagnostic purposes •Insertion of alarm indication signal ("all ones")•Flexible hardware or software controlled device configuration •Device power down functionHardware Interface Mode•DS3/STS-1 or E3•Line Coding (E3: HDB3 or AMI; DS3/STS-1: B3ZS or AMI)•Transmitter disable•Power down•Remote loop•Local loop•Single/dual rail operation•Receive clock edge selection•Transmit clock edge selection•Transmit "all ones"•Receive line monitoring mode•Automatic RDOP/RDON blanking option•Jitter attenuation•Loss of signal indication•Bipolar violation indicationMicroprocessor Interface Mode•Microprocessor bus compatible interface•Hardware control lines directly accessibleGeneral•CMOS device•P-MQFP-44-2 package (body size 10 mm × 10 mm, lead pitch 0.8 mm)•Single power supply: 3.3 V ± 5%•5V-tolerant digital input lines•Temperature range of -40°C to +85°C•Low power deviceApplications•Interface for SONET/DS3 and E3 network equipment•WAN gateways•CSU/DSU•Multiplexers•Digital crossconnect systems•DS3/STS-1/E3 Test Equipment1.2Logic SymbolFigure1Logic Symbol1.3Typical ApplicationsFigure2 to Figure4 show typical applications using the TE3-LIU™.Figure2T3/T1 Multiplexer ApplicationFigure3Channelized T3 Link Layer ApplicationFigure4Unchannelized T3 Link Layer ApplicationNote:TE3-MUX™ (PEB 3445) is an M13 MU ltiple X er/demultiplexer with an integrated DS3 framerQuadLIU™ (PEB 22504) is a 4-channel L ine I nterface U nit for E1/T1/J1DSCC4™ (PEB 20534) is a 4-channel S erial C ommunication C ontrollerTE3-CHATT™ (PEB 3456) is a CHA nnelized T3 T ermination with DS3 Framer, M13 Multiplexer, T1/E1 Framers and 256 Channel HDLC/PPP controller2Pin Descriptions 2.1Pin DiagramFigure5Pin Configuration2.2Pin Definitions and FunctionsTable1Interface Pin FunctionsFunctionPin No.Symbol Input (I)Output (O)Supply (S)Receive Direction9RL1I (analog)Line Receiver 1Analog input from the external transformer(receive bipolar ring).The signal at RL1 must be coded accordingto B3ZS or HDB3.10RL2I (analog)Line Receiver 2Analog input from the external transformer(receive bipolar tip).The signal at RL1 must be coded accordingto B3ZS or HDB3.25RDOP O Receive Data Output/PositiveReceived data at RL1/2 is sent onRDOP/RDON to the framer interface. Datais clocked with the rising or falling edge ofRCLK, depending on RPE.In single rail mode (DR/SR=0), data is sentin NRZ format.24RDON O Receive Data Output/NegativeIf dual rail data format is selected, thenegative data signal is output onRDON/BPV.BPV Bipolar ViolationIf single rail data format is selected, thebipolar violation indication signal is outputon RDON/BPV. BPV is synchronized onRCLK.26RCLK O Receive ClockReceive Clock extracted from the incomingdata pulses. The active clock edge isdetermined by RPE.During LOS, a clock signal is generatedinternally and driven on RCLK (derivedfrom REFCLK).Transmit Direction 1XL1O (analog)Transmit Line 1 (transmit bipolar ring)Analog output to the external transformer. XL1 can be switched into inactive mode.3XL2O (analog)Transmit Line 2 (transmit bipolar tip)Analog output to the external transformer.XL2 can be switched into inactive mode.31XDIP I + PUTransmit Data In/PositiveTransmit data received from the framer interface to be output on XL1/2. NRZ or dual rail positive data has to be provided at XDIP. Latching of data is done with the rising or falling transitions of XCLK, depending on XPE.32XDIN I + PUTransmit Data In/NegativeIf dual rail format is selected, negative data signal is read from XDIN. If single rail data format is selected, data on XDIN is ignored. Latching of data is done with the rising or falling transitions of XCLK, depending on XPE.30XCLK I + PUTransmit ClockInput of the working clock for the transmitter. The active clock edge is determined by XPE.DS3: 44.736 MHz STS-1: 51.840 MHz E3: 34.368 MHzTo fulfill e.g. ITU-T G.832 a clock accuracy of 20 ppm is required. For correct function a clock signal has always to be supplied to XCLK.Table 1Interface Pin Functions (cont’d)Pin No.SymbolInput (I)Output (O)Supply (S)FunctionGlobal Clock Reference 29REFCLKIReference ClockREFCLK is the basic internal clock. It must be stable during reset and operation.This clock is also used to synchronize the receive PLL in case of no signal.The clock frequency depends on the target application:DS3: 44.736 MHz STS-1: 51.840 MHz E3: 34.368 MHzTo fulfill e.g., ITU-T G.832 a clock accuracy of 20 ppm is required.39XTAL1I Jitter Attenuation ReferenceConnection for an external pullable crystal.DS3:14.912 MHz STS-1:17.280 MHz E3:11.456 MHz If jitter attenuation is disabled (default), XTAL1 is internally driven to a fixed level (not floating).38XTAL2OTable 1Interface Pin Functions (cont’d)Pin No.SymbolInput (I)Output (O)Supply (S)FunctionTable2Control Pin FunctionsPin No.Symbol Input (I)FunctionOutput (O)Supply (S)33RES I Hardware ResetA low signal at this pin forces the deviceinto reset state.23CS I + PU Chip Select0 = hardware control signals are switchedthrough1 = hardware control signals are ignored 5DS3/E3I + PU DS3/STS-1 or E3 SelectPrimary mode selection. This signal has tobe stable during reset and may not changeafterwards. It must not be connected to aµP bus.0 = E31 = DS3 or STS-1 (see DS3/STS-1)4DS3/STS-1I + PU DS3 or STS-1 SelectPrimary mode selection. This signal has tobe stable during reset and may not changeafterwards. It must not be connected to aµP bus.0 = STS-11 = DS313LCODE I + PU Line Code Selectfor receive and transmit directionE3:0 = AMI1 = HDB3DS3/STS-1:0 = AMI1 = B3ZS16XAIS I + PU Transmit Alarm Indication0 = no AIS1 = AIS all-ones insertion。

NO Abbr aa1ABM Activity-based Management2AO Application Outsourcing3APICS American Production and Inventory4APICS Applied Manufacturing Education S5APO Advanced Planning and Optimizatio6APS Advanced Planning and Scheduling7ASP Application Service/Software Prov8ATO Assemble To Order9ATP Available To Promise10B2B Business to Business11B2C Business to Consumer12B2G Business to Government13B2R Business to Retailer14BIS Business Intelligence System15BOM Bill Of Materials16BOR Bill Of Resource17BPR Business Process Reengineering18BPM Business Process Management19BPS Business Process Standard20C/S Client/Server(C/S)\Browser/Server21CAD Computer-Aided Design22CAID Computer-Aided Industrial Design23CAM Computer-Aided Manufacturing24CAPP Computer-Aided Process Planning25CASE Computer-Aided Software Engineeri26CC Collaborative Commerce27CIMS Computer Integrated Manufacturing28CMM Capability Maturity Model29COMMS Customer Oriented Manufacturing M30CORBA Common Object Request Broker Arch31CPC Collaborative Product Commerce32CPIM Certified Production and Inventor33CPM Critical Path Method34CRM Customer Relationship Management35CRP capacity requirements planning36CTI Computer Telephony Integration37CTP Capable to Promise38DCOM Distributed Component Object Mode39DCS Distributed Control System40DMRP Distributed MRP41DRP Distribution Resource Planning42DSS Decision Support System43DTF Demand Time Fence44DTP Delivery to Promise45EAI Enterprise Application Integratio46EAM Enterprise Assets Management47ECM Enterprise Commerce Management48ECO Engineering Change Order49EDI Electronic Data Interchange50EDP Electronic Data Processing51EEA Extended Enterprise Applications 52EIP Enterprise Information Portal53EIS Executive Information System54EOI Economic Order Interval55EOQ Economic Order Quantity56EPA Enterprise Proficiency Analysis 57ERP Enterprise Resource Planning58ERM Enterprise Resource Management59ETO Engineer To Order60FAS Final Assembly Schedule61FCS Finite Capacity Scheduling62FMS Flexible Manufacturing System63FOQ Fixed Order Quantity64GL General Ledger65GUI Graphical User Interface66HRM Human Resource Management67HRP Human Resource Planning68IE Industry Engineering/Internet Exp 69ISO International Standard Organizati 70ISP Internet Service Provider71ISPE International Society for Product 72IT/GT Information/Group Technology73JIT Just In Time74KPA Key Process Areas75KPI Key Performance Indicators76LP Lean Production77MES Manufacturing Executive System78MIS Management Information System79MPS Master Production Schedule80MRP Material Requirements Planning81MRPII Manufacturing Resource Planning 82MTO Make To Order83MTS Make To Stock84OA Office Automation85OEM Original Equipment Manufacturing 86OPT Optimized Production Technology 87OPT Optimized Production Timetable88PADIS Production And Decision Informati 89PDM Product Data Management90PERT Program Evaluation Research Techn 91PLM Production Lifecycle Management 92PM Project Management93POQ Period Order Quantity94PRM Partner Relationship Management95PTF Planned Time Fence96PTX Private Trade Exchange97RCCP Rough-Cut Capacity Planning98RDBM Relational Data Base Management99RPM Rapid Prototype Manufacturing100RRP Resource Requirements Planning101SCM Supply Chain Management102SCP Supply Chain Partnership103SFA Sales Force Automation104SMED Single-Minute Exchange Of Dies105SOP Sales And Operation Planning106SQL Structure Query Language107TCO Total Cost Ownership108TEI Total Enterprise Integration109TOC Theory Of Constraints/Constraints110TPM Total Productive Maintenance111TQC Total Quality Control112TQM Total Quality Management113WBS Work Breakdown System114XML eXtensible Markup Language115ABC Classification(Activity Based Classification) 116ABC costing117ABC inventory control118abnormal demand119acquisition cost ,ordering cost120action message121action report flag122activity cost pool123activity-based costing(ABC)124actual capacity125adjust on hand126advanced manufacturing technology127advanced pricing128AM Agile Manufacturing129alternative routing130Anticipated Delay Report131anticipation inventory132apportionment code133assembly parts list134automated storage/retrieval syste135Automatic Rescheduling136available inventory137available material138available stock139available work140average inventory141back order142back scheduling143base currency144batch number145batch process146batch production147benchmarking148bill of labor149bill of lading150branch warehouse151bucketless system152business framework153business plan154capacity level155capacity load156capacity management157carrying cost158carrying cost rate159cellular manufacturing160change route161change structure162check point163closed loop MRP164Common Route Code(ID)165component-based development 166concurrent engineering167conference room pilot168configuration code169continuous improvement170continuous process171cost driver172cost driver rate173cost of stockout174cost roll-up175crew size176critical part177critical ratio178critical work center179CLT Cumulative Lead Time180current run hour181current run quantity182customer care183customer deliver lead time 184customer loyalty185customer order number186customer satisfaction187customer status188cycle counting189DM Data Mining190Data Warehouse191days offset192dead load193demand cycle194demand forecasting195demand management196Deming circle197demonstrated capacity198discrete manufacturing199dispatch to200DRP Distribution Requirements Plannin 201drop shipment202dunning letter203ECO workbench204employee enrolled205employee tax id206end item207engineering change mode flag208engineering change notice209equipment distribution210equipment management211exception control212excess material analysis213expedite code214external integration215fabrication order216factory order217fast path method218fill backorder219final assembly lead time220final goods221finite forward scheduling222finite loading223firm planned order224firm planned time fence225FPR Fixed Period Requirements226fixed quantity227fixed time228floor stock229flow shop230focus forecasting231forward scheduling232freeze code233freeze space234frozen order235gross requirements236hedge inventory237in process inventory238in stock239incrementing240indirect cost241indirect labor242infinite loading243input/output control244inspection ID245integrity246inter companies247interplant demands248inventory carry rate249inventory cycle time250inventory issue251inventory location type 252inventory scrap253inventory transfers254inventory turns/turnover 255invoice address256invoice amount gross257invoice schedule258issue cycle259issue order260issue parts261issue policy262item availability263item description264item number265item record266item remark267item status268job shop269job step270kit item271labor hour272late days273lead time274lead time level275lead time offset days276least slack per operation 277line item278live pilot279load leveling280load report281location code282location remarks283location status284lot for lot285lot ID286lot number287lot number traceability288lot size289lot size inventory290lot sizing291low level code292machine capacity293machine hours294machine loading295maintenance ,repair,and operating 296make or buy decision297management by exception298manufacturing cycle time299manufacturing lead time300manufacturing standards301master scheduler302material303material available304material cost305material issues and receipts306material management307material manager308material master,item master309material review board310measure of velocity311memory-based processing speed312minimum balance313Modern Materials Handling314month to date315move time , transit time316MSP book flag317multi-currency318multi-facility319multi-level320multi-plant management321multiple location322net change323net change MRP324net requirements325new location326new parent327new warehouse328next code329next number330No action report331non-nettable332on demand333on-hand balance334on hold335on time336open amount337open order338order activity rules339order address340order entry341order point342order point system343order policy344order promising345order remarks346ordered by347overflow location348overhead apportionment/allocation 349overhead rate,burden factor,absor 350owner's equity351parent item352part bills353part lot354part number355people involvement356performance measurement357physical inventory358picking359planned capacity360planned order361planned order receipts362planned order releases363planning horizon364point of use365Policy and procedure366price adjustments367price invoice368price level369price purchase order370priority planning371processing manufacturing372product control373product family374product mix375production activity control376production cycle377production line378production rate379production tree380PAB Projected Available Balance 381purchase order tracking382quantity allocation383quantity at location384quantity backorder385quantity completion386quantity demand387quantity gross388quantity in389quantity on hand390quantity scrapped391quantity shipped392queue time393rated capacity394receipt document395reference number396regenerated MRP397released order398reorder point399repetitive manufacturing 400replacement parts401required capacity402requisition orders403rescheduling assumption404resupply order405rework bill406roll up407rough cut resource planning 408rounding amount409run time410safety lead time411safety stock412safety time413sales order414scheduled receipts415seasonal stock416send part417service and support418service parts419set up time420ship address421ship contact422ship order423shop calendar424shop floor control425shop order , work order426shrink factor427single level where used428standard cost system429standard hours430standard product cost431standard set up hour432standard unit run hour433standard wage rate434status code435stores control436suggested work order437supply chain438synchronous manufacturing439time bucket440time fence441time zone442top management commitment443total lead time444transportation inventory445unfavorable variance, adverse446unit cost447unit of measure448value chain449value-added chain450variance in quantity451vendor scheduler,supplier schedul 452vendor scheduling453Virtual Enterprise(VE)/ Organizat 454volume variance455wait time456where-used list457work center capacity458workflow459work order460work order tracking461work scheduling462world class manufacturing excelle 463zero inventories464465Call/Contact/Work/Cost center 466Co/By-product467E-Commerce/E-Business/E-Marketing 468E-sales/E-procuement/E-partner 469independent/dependent demand470informal/formal system471Internet/Intranet/Extranet472middle/hard/soft/share/firm/group ware 473pegging/kitting/netting/nettable474picking/dispatch/disbursement lis475preflush/backflush/super backflus476yield/scrap/shrinkage (rate)477scrap/shrinkage factor478479costed BOM480engineering BOM481indented BOM482manufacturing BOM483modular BOM484planning BOM485single level BOM486summarized BOM487488account balance489account code490account ledger491account period492accounts payable493accounts receivable494actual cost495aging496balance due497balance in hand498balance sheet499beginning balance500cash basis501cash on bank502cash on hand503cash out to504catalog505category code506check out507collection508cost simulation509costing510current assets511current liabilities512current standard cost513detail514draft remittance515end of year516ending availables517ending balance518exchange rate519expense520financial accounting521financial entity522financial reports523financial statements524fiscal period525fiscal year526fixed assets527foreign amount528gains and loss529in balance530income statement531intangible assets532journal entry533management accounting534manual reconciliation535notes payable536notes receivable537other receivables538pay aging539pay check540pay in541pay item542pay point543pay status544payment instrument545payment reminder546payment status547payment terms548period549post550proposed cost551simulated cost552spending variance,expenditure var 553subsidiary554summary555tax code556tax rate557value added tax558559as of date , stop date560change lot date561clear date562date adjust563date available564date changed565date closed566date due567date in produced568date inventory adjust569date obsolete570date received571date released572date required573date to pull574earliest due date575effective date576engineering change effect date 577engineering stop date578expired date579from date580last shipment date581need date582new date583pay through date584receipt date585ship date586587allocation588alphanumeric589approver590assembly591backlog592billing593bill-to594bottleneck595bulk596buyer597component598customer599delivery600demand601description602discrete603ergonomics604facility605feature606forecast607freight608holidays609implement610ingredient611inquire612inventory613item614job615Kanban616level617load618locate619logistics620lot621option622outstanding623overhead624override625overtime626parent627part628phantom629plant630preference631priority632procurement633prototyping634queue635quota636receipt637regeneration638remittance639requisition640returned641roll642routing643schedule644shipment645ship-to646shortage647shrink648spread649statement650subassembly651supplier652transaction653what-if654655post-deduct inventory transaction 656pre-deduct inventory transaction 657generally accepted manufacturing658direct-deduct inventory transacti 659Pareto Principle660Drum-buffer-rope661663Open Database Connectivity664Production Planning665Work in Process666accelerated cost recovery system 667accounting information system668acceptable quality kevel669constant purchasing power account 670break-even analysis671book value672cost-benefit analysis673chief financial office674degree of financial leverage675degree of operating leverage676first-in , first-out677economic lot size678first-in ,still-here679full pegging680linear programming681management by objective682value engineering683zero based budgeting684CAQ computer aided quality assurance 685DBMS database management system686IP Internet Protocol687TCP T ransmission Control Protocol 689690API Advanced Process Industry691A2A Application to Application692article693article reserves694assembly order695balance-on-hand-inventory696bar code697boned warehouse698CPA Capacity Requirements Planning 699change management700chill space701combined transport702commodity inspection703competitive edge704container705container transport706CRP Continuous Replenishment Program707core competence708cross docking709CLV Customer Lifetime Value710CReM Customer Relationship Marketing 711CSS Customer Service and Support712Customer Service Representative 713customized logistics714customs declaration715cycle stock716data cleansing717Data Knowledge and Decision Suppo 718data level integration719data transformation720desktop conferencing721distribution722distribution and logistics723distribution center724distribution logistics725distribution processing726distribution requirements727DRP distribution resource planning 728door-to-door729drop and pull transport730DEM Dynamic Enterprise Module731ECR Efficient Consumer Response732e-Government Affairs733EC Electronic Commerce734Electronic Display Boards735EOS Electronic order system736ESD Electronic Software Distribution 737embedding738employee category739empowerment740engineering change effect work or 741environmental logistics742experiential marketing743export supervised warehouse744ERP Extended Resource Planning745field sales/cross sale/cross sell 746franchising747FCL Full Container Load748Global Logistics Management749goods collection750goods shed751goods shelf752goods stack753goods yard754handing/carrying755high performance organization756inland container depot757inside sales758inspection759intangible loss760internal logistics761international freight forwarding 762international logistics763invasive integration764joint distribution765just-in-time logistics766KM Knowledge Management767lead (customer) management768learning organization769LCL less than container load770load balancing771loading and unloading772logistics activity773logistics alliance774logistics center775logistics cost776logistics cost control777logistics documents778logistics enterprise779logistics information780logistics management781logistics modulus782logistics network783logistics operation784LRP Logistics Resource Planning785logistics strategy786logistics strategy management787logistics technology788MES Manufacture Execute System789mass customization790NPV Net Present Value791neutral packing792OLAP On-line Analysis Processing793OAG Open Application Group794order picking795outsourcing796package/packaging797packing of nominated brand798palletizing799PDA Personal Digital Assistant800personalization801PTF Planning time fence802POS Point Of Sells803priority queuing804PBX Private Branch Exchange805production logistics806publish/subscribe807quality of working life808Quick Response809receiving space810REPs Representatives811return logistics812ROI Return On Investment813RM Risk Management814sales package815scalability816shipping space817situational leadership818six sigma819sorting/stacking820stereoscopic warehouse821storage822stored procedure823storehouse824storing825SRM Supplier Relationship Management 826tangible loss827team building828TEM Technology-enabled Marketing829TES Technology-enabled Selling830TSR TeleSales Service Representative 831TPL Third-Part Logistics832through transport833unit loading and unloading834Value Management835value-added logistics service 836Value-chain integration837VMI Vender Managed Inventory838virtual logistics839virtual warehouse840vision841volume pricing model842warehouse843waste material logistics844workflow management845zero latency846ZLE Zero Latency Enterprise847ZLP Zero Latency Process848zero-inventory technologyCC S F NUM基于作业活动管理F10应用程序外包E21美国生产与库存管理协会ext L651实用制造管理系列培训教材ext C652先进计划及优化技术F14高级计划与排程技术F15应用服务/软件供应商L22定货组装L24可供销售量(可签约量)L31企业对企业(电子商务)F51企业对消费者(电子商务)F52企业对政府(电子商务)F53企业对经销商(电子商务)F54商业智能系统E47物料清单bom L471资源清单L43业务/企业流程重组E49业务/企业流程管理E49业务/企业流程标准E50客户机/服务器\浏览器/服务器abr L457计算机辅助设计L75计算机辅助工艺设计L76计算机辅助制造L77计算机辅助工艺设计L78计算机辅助软件工程L79协同商务E68计算机集成制造系统L73能力成熟度模型L55面向客户制造管理系统ext L653通用对象请求代理结构F70协同产品商务E69生产与库存管理认证资格ext F654关键线路法L92客户关系管理L102能力需求计划L60电脑电话集成(呼叫中心)L74可承诺的能力F56分布式组件对象模型F121分布式控制系统L122分布式MRP L123分销资源计划L125决策支持系统L110需求时界L115可承诺的交货时间F111企业应用集成E140企业资源管理E141企业商务管理F142工程变更订单D139电子数据交换L131电子数据处理F132扩展企业应用系统F152企业信息门户E143高层领导信息系统F150经济定货周期L129经济订货批量(经济批量法)L130企业绩效分析144企业资源计划L145企业资源管理L145专项设计，按订单设计L136最终装配计划L160有限能力计划L162柔性制造系统L171固定定货批量法L167总账cid D522图形用户界面F178人力资源管理L181人力资源计划L182工业工程/浏览器188国际标准化组织F194互联网服务提供商F195国际生产力促进会ext F655信息/成组技术abr F458准时制造/准时制生产L218关键过程域L220关键业绩指标F219精益生产L227制造执行系统L254管理信息系统L252主生产计划L259物料需求计划L268制造资源计划D256定货(订货)生产L249现货(备货)生产L250办公自动化L292原始设备制造商E311最优生产技术E300最优生产时刻表E301生产和决策管理信息系统L346产品数据管理L342计划评审技术L352产品生命周期管理E348项目管理353周期定量法L323合作伙伴关系管理F320计划时界L330自用交易网站F339粗能力计划L385关系数据库管理F372快速原形制造F367资源需求计划D380供应链管理L420供应链合作伙伴关系L421销售自动化L392快速换模法L408销售与运作规划L391结构化查询语言F417总体运营成本F428全面企业集成F429约束理论/约束管理L423全员生产力维护F431全面质量控制L432全面质量管理L433工作分解系统F448可扩展标记语言F153 ABC分类法T1作业成本法F2 ABC 库存控制D3反常需求D4定货费L5行为/活动(措施)信息D6活动报告标志D7作业成本集L8作业基准成本法/业务成本法L9实际能力D11调整现有库存量D12先进制造技术L13高级定价系统D16敏捷制造L17替代工序(工艺路线)D18拖期预报T19预期储备L20分摊码D23装配零件表D25自动仓储/检索系统C26计划自动重排T27可达到库存D28可用物料D29达到库存T30可利用工时T32平均库存D33欠交(脱期)订单L34倒排(序)计划/倒序排产?L35本位币D36批号D37批流程L38批量生产D39标杆瞄准(管理)sim F586工时清单D41提货单D42分库D44无时段系统L45业务框架D46经营规划L48能力利用水平L57能力负荷D58能力管理L59保管费L61保管费率D62单元式制造T63修改工序D64修改产品结构D65检查点sim D66闭环MRP L67通用工序标识T71组件(构件)开发技术F72并行(同步)工程L80会议室模拟L81配置代码D82进取不懈C84连续流程L85作业成本发生因素L86作业成本发生因素单位费用L87短缺损失L88成本滚动计算法L89班组规模D90急需零件D91紧迫系数L93关键工作中心L94累计提前期L95现有运转工时D96现有运转数量D97客户关怀D98客户交货提前期L99客户忠诚度F100客户订单号D101客户满意度F103客户状况D104周期盘点L105数据挖掘F106数据仓库F107偏置天数L108空负荷T109需求周期L112需求预测D113需求管理L114戴明环ext L116实际能力C117离散型生产L119调度D120分销需求计划L124直运C126催款信D127 ECO工作台D128在册员工D133员工税号D134最终产品D135工程变更方式标志D137工程变更通知D138设备分配D146设备管理D147例外控制D148呆滞物料分析D149急送代码T151外部集成F154加工订单T155工厂订单D156快速路径法D157补足欠交D158总装提前期D159成品D161有限顺排计划L163有限排负荷L164确认的计划订单L165确认计划需求时界L166定期用量法L168固定数量法D169固定时间法D170作业现场库存L172流水车间T173调焦预测T174顺排计划L175冻结码D176冷冻区D176冻结订单D177毛需求L179囤积库存L180在制品库存D183在库D184增值D185间接成本D186间接人工D187无限排负荷L189投入/产出控制L190检验标识D191完整性D192公司内部间D193厂际需求量T196库存周转率D197库存周期D197库存发放D198仓库库位类型D199库存报废量D200库存转移D201库存(资金)周转次数L202发票地址D203发票金额D204发票清单D205发放周期D206发送订单T207发放零件D208发放策略D209项目可供量D210项目说明D211项目编号D212项目记录T213项目备注D214项目状态D215加工车间L216作业步骤D217配套件项目D221人工工时D222延迟天数D223提前期L224提前期水平D225提前期偏置(补偿)天数D226最小单个工序平均时差C228单项产品T229应用模拟L230负荷量T231负荷报告T232仓位代码D233仓位备注T234仓位状况T235按需定货(因需定量法/缺补法)L236批量标识T237批量编号T238批号跟踪D239批量D240批量库存L241批量规划L242低层(位)码L243机器能力D244机时D245机器加载T246维护修理操作物料C247外购或自制决策D248例外管理法L251制造周期时间T253制造提前期D255制造标准D257主生产计划员L260物料L261物料可用量L262物料成本D263物料发放和接收D264物料管理L265物料经理L266物料主文件L267物料核定机构L269生产速率水平C270基于存储的处理速度F271最小库存余量L272现代物料搬运C273月累计D274传递时间L275 MPS登录标志T276多币制D277多场所D278多级D279多工厂管理F280多重仓位T281净改变法L282净改变式MRP T283净需求L284新仓位D285新组件D286新仓库D287后续编码D288后续编号D289不活动报告D290不可动用量C291急需的D293现有库存量D294挂起D295准时D296未清金额D298未结订单/开放订单L299订单活动规则D302订单地址D303订单输入T304定货点T305定货点法L306定货策略L307定货承诺T308定货备注T309定货者D310超量库位D312间接费分配L313间接费率L314所有者权益L315母件L316零件清单D317零件批次D318零件编号D319全员参治C321业绩评价L322实际库存D324领料/提货D325计划能力L326计划订单L327计划产出量L328计划投入量L329计划期/计划展望期L331使用点C332工作准则与工作规程L333价格调整D334发票价格D335物价水平D336采购订单价格D337优先计划D338流程制造D340产品控制D341产品系列D343产品搭配组合C344生产作业控制L345生产周期L347产品线D349产品率D350产品结构树T351预计可用库存(量)L354采购订单跟踪D355已分配量D356仓位数量T357欠交数量D358完成数量D359需求量D360毛需求量D361进货数量T362现有数量D363废品数量D364发货数量D365排队时间L366额定能力L368收款单据D369参考号D370重生成式MRP T371下达订单L373再订购点D374重复式生产(制造)L375替换零件D376需求能力L377请购单D378重排假设T379补库单L381返工单D382上滚D383粗资源计划D384舍入金额D386加工(运行)时间L387安全提前期L388安全库存L389保险期T390销售订单D393计划接收量(预计入库量/预期到货量)L394季节储备L395发送零件T396服务和支持D397维修件T398准备时间L399发运地址D400发运单联系人D401发货单D402工厂日历(车间日历)L403车间作业管理(控制)L404车间订单L405损耗因子(系数)D406单层物料反查表D407标准成本体系L409标准工时D410标准产品成本D411标准机器设置工时T412标准单位运转工时T413标准工资率T414状态代码D415库存控制T416建议工作单D418供应链L419同步制造/同期生产C422时段(时间段)L424时界L425时区L426领导承诺C427总提前期L430在途库存L434不利差异L435单位成本T436计量单位D437价值链L438增值链C439量差D440采购计划员/供方计划员L442采购计划法T443虚拟企业/公司L444产量差异L445等待时间L446反查用物料单L447工作中心能力L449工作流L450工作令T451工作令跟踪T452工作进度安排T453国际优秀制造业C454零库存T455456呼叫/联络/工作/成本中心abr X459联/副产品abr X460电子商务/电子商务/电子集市abr X461电子销售/电子采购/电子伙伴abr独立需求/相关需求件abr X462非/规范化管理系统abr X463互联网/企业内部网/企业外联网abr X464中间/硬/软/共享/固/群件abr X465追溯(反查)/配套出售件/净需求计算abr X466领料单(或提货单)/派工单/发料单abr X467预冲/倒冲法/完全反冲abr X468成品率/废品率/缩减率abr X469残料率（废品系数）/损耗系数abr fromchen470成本物料清单bom D472设计物料清单bom L473缩排式物料清单bom L474制造物料清单bom L475模块化物料清单bom L476计划物料清单bom L477单层物料清单bom D478汇总物料清单bom L479480账户余额cid D481账户代码cid D482分类账cid D483会计期间cid D484应付账款cid L485应收账款cid L486实际成本cid D487账龄cid D488到期余额cid D489现有余额cid D490资产负债表cid D491期初余额cid D492现金收付制cid D493银行存款cid L494现金cid L495支付给cid D496目录cid D497分类码cid D498结帐cid D499催款cid D500成本模拟cid D501成本核算cid D502流动资产cid L503流动负债cid L504现行标准成本cid C505明细cid D506汇票汇出cid D507年末cid D508期末可供量cid D509期末余额cid D510汇率cid D511费用cid D512财务会计cid L513财务实体cid L514财务报告cid D515财务报表cid D516财务期间cid D517财政年度cid D518固定资产cid L519外币金额cid D520损益cid D521平衡cid D523损益表cid D524无形资产cid L525分录cid D526管理会计cid L527手工调账cid D528应付票据cid L529应收票据cid L530其他应收款cid L531付款账龄cid D532工资支票cid D533缴款cid D534付款项目cid D535支付点cid D536支付状态cid D537付款方式cid D538催款单cid D539付款状态cid D540付款期限cid D541期间cid D542过账cid D543建议成本cid L544模拟成本cid L545开支差异cid L546明细账cid D547汇总cid D548税码cid D549税率cid D550增值税cid D551552截止日期dat D553修改批量日期dat D554结清日期dat D555调整日期dat D556有效日期dat D557修改日期dat D558结束日期dat D559截止日期dat560生产日期dat D561库存调整日期dat D562作废日期dat D563收到日期dat D564交付日期dat D565需求日期dat D566发货日期dat D567最早订单完成日期dat L568生效日期dat D569工程变更生效日期dat D570工程停止日期dat D571失效日期，报废日期dat D572起始日期dat D573最后运输日期dat T574需求日期dat D575新日期dat D576付款截止日期dat D577收到日期dat D578发运日期dat D579580已分配量sim D581字母数字sim C582批准者sim D583装配(件)sim D584未结订单/拖欠订单sim L585开单sim D587发票寄往地sim C588瓶颈资源sim L589散装sim D590采购员sim T591子件/组件sim L592客户sim D593交货sim D594需求sim D595说明sim D596离散sim D597工效学(人类工程学)sim L598设备、功能sim D599基本组件/特征件sim L600预测sim D601运费sim D602例假日sim D603实施sim D604配料、成分sim D605查询sim D606库存sim L607物料项目sim D608作业sim D609看板sim T610层次(级)sim D611负荷sim D612定位sim D613后勤保障体系；物流管理sim L614批次sim D615可选件sim L616逾期未付sim D617制造费用sim D618覆盖sim C619加班sim D620双亲(文件)sim D621零件sim D622虚拟件sim L623工厂，场所sim D624优先权sim D626优先权(级)sim D627采购sim628原形测试sim L629队列sim T630任务额，报价sim D631收款、收据sim D632全重排法sim C633汇款sim D634请购单sim L635退货sim D636滚动sim D637工艺线路sim L638计划表sim D639发运量sim D640交货地sim C641短缺sim D642损耗sim D643分摊sim D644报表sim D645子装配件sim D646供应商sim D647事务处理sim F648如果怎样-将会怎样sim C649650后减库存处理法ext T656前减库存处理法ext T657通用生产管理原则ext T658直接增减库存处理法ext T659帕拉图原理ext L660鼓点-缓冲-绳子ext T661开放数据库互连fromchen生产规划编制 fromchen在制品 fromchen快速成本回收制度fromchen会计信息系统 fromchen可接受质量水平 fromchen不买够买力会计fromchen保本分析fromchen帐面价值fromchen成本效益分析fromchen财务总监fromchen财务杠杆系数fromchen经济杠杆系数fromchen先进先出法 fromchen经济批量 fromchen后进先出法fromchen完全跟踪 fromchen线性规划 fromchen目标管理 fromchen价值工程 fromchen零基预算fromchen计算机辅助质量保证 fromchen数据库管理系统 fromchen网际协议 fromchen传输控制协议 fromchen高级流程工业fromAMT应用到应用(集成)fromAMT物品fromAMT物品存储fromAMT装配订单fromAMT现有库存余额fromAMT条形码fromAMT保税仓库fromAMT能力需求计划fromAMT变革管理fromAMT冷藏区fromAMT联合运输fromAMT进出口商品检验fromAMT竞争优势fromAMT集装箱fromAMT集装箱运输fromAMT连续补充系数fromAMT。