IC610安装说明(图文版)

e-mail:**************For latest product manuals:User’s Guide IP610 SERIESI/P ConvertersShop online at422GA. wire leadsapprox. 18" longpos, neg, grd ContentsSectionDescription Page 1.0Installation & Approvals 32.0 Operation 73.0 Maintenance & Repairs 84.0 Trou b leshooting8IP610 SERIES I/P ConvertersShaded areas and associated dimensions apply to the zero based unit only.Refers to conditions or hazards which could result in serious personal injury or death.Refers to conditions or hazards which could result in personal injury.Refers to conditions or hazards which could result in equipment or property damage.Alerts you to facts or special instructions.ALL DANGER, WARNING, AND CAUTION NOTICES MUST BE COMPLIED WITH IN FULL.Functional SpecificationsS TA N D A R D R A N G E Z E R O-B A S E D R A N G EInputs4-20 mA 4-20 mAOutputs3-15 psig0.20-1.00 BAR0-30 psig0.00-2.00 BAR3-27 psig0.20-1.80 BAR0-60 psig0.00-4.00 BAR6-30 psig0.40-2.00 BAR0-120 psig0.00-8.00 BAR2-60 psig0.14-4.00 BAR3-120 psig0.20-8.00 BARAir Consumption 1.8 scfh (0.05 m3/hr) at mid range typical 6.0 scfh at mid range typicalSupply Pressure100 psig (6.90 BAR) max. (3-15, 3-27, 6-30 psig)100 psig (6.90 BAR) max. (0-30, 0-60 psig) Note: Supply pressure must bea minimum of 5 psig (0.3 BAR)150 psig (10.00 BAR) max. (0-120 psig) above maximum output150 psig (10.00 BAR) max. (2-60, 3-120 psig)Flow Capacity 4.5 scfm (7.7 m3/hr) 12.0 scfm (20.0 m3/hr) atat25 psig (1.70 BAR) supply (3-15, 3-27, 6-30 psig) 100 psig (6.90 BAR) supply (0-30, 0-60 psig)12.0 scfm (20.0 m3/hr) 20.0 scfm (34.0 m3/hr)at 100 psig (6.90 BAR) supply (3-15, 3-27, 6-30, 2-60 psig)at 150 psig (10.00 BAR) supply (0-120 psig)20.0 scfm (34.0 m3/hr)at 150 psig (10.00 BAR) supply (3-120 psig)Temperature Limits-20°to +150°F (-30°to +65°C)-20°to +150°F (-30°to +65°C) Impedance4-20 mA3-15 psig180 Ohms4-20 mA0-30 psig290 Ohms3-27 psig240 Ohms0-60 psig300 Ohms6-30 psig240 Ohms0-120 psig315 Ohms2-60 psig245 Ohms3-120 psig280 OhmsPerformance SpecificationsS TA N D A R D R A N G E Z E R O-B A S E D R A N G E Linearity (Independent)<±0.5% of span<±1.5% of spanHysteresis, and Repeatability<0.5% of span<1.0% of spanSupply Pressure Sensitivity<0.1% of span per 1.0 psig (0.07 BAR)<0.02% of span per 1.0 psig (0.07 BAR)lPhysical SpecificationsPort Sizes Pneumatic1/4” NPTMedia Clean, dry, oil-free, instrument air, filtered to 40 micronElectricalConnections Conduit 1/2” NPT, DIN 43650Mounting Direct wall, panel, 1 1/2” pipe, DIN railMaterials Housing Chromate-treated aluminum with epoxy paint. NEMA 4X (IP65)Elastomers Buna-NTrim Stainless steel; brass; zinc-plated steelWeight Standard Unit: 1.3 lbs Zero-based Unit: 1.7 lbs1.1 Pre-installation Requirements1.1.1Environment: Suitable for installation in the following locations:•Intrinsically safe operation in hazardous locations outdoors (NEMA 4X, CSA.ENC.4 & IP65)•See section 1.5, 1.6 and 1.7 for Factory Mutual (FM), Canadian Standards (CSA).All wiring must be made to all local and national codes appropriateto the area of installation.1.1.2Electrical Input: 4-20 mAdc current source.1.1.3 Air supply: Clean, dry, oil free instrument air filtered to 40 micronClean all pipe lines to remove dirt and scale prior to installation. Failures attributableto instrument air supply contamination are not covered by the warranty.This instrument vents to atmosphere. The use of supply gas otherthan air can create a hazardous environment.1.2 Mounting1.2.1The IP610 has a standard mounting kit that enables 11/2”pipe, panel or wall mounting of the unit.1.2.2To mount unit to a 11/2”pipe, use two 10-32 holes on the back of the unit to attach bracket to transducer. Then place U-bolt around pipe and through bracket. Place nuts on U-bolt and tighten (see figure 1).1.2.3With access to the rear of a panel, attach transducer using two 10-32 screws and the two threaded mountingscrews on the back of the unit. With no access to the back of the panel, attach the bracket to the transducer using the two 10-32 holes on the back of unit and mount bracket to panel using four 10-32 screws (see figure 2).1.2.4Due to it’s light weight, the IP610 can also be mounted in line with support provided by the supply and output piping.Figure 1 - Pipe MountingFigure 2 - Panel Mounting Shaded areas and associated dimensions apply to the zero based unit only.1.2.5The IP610 can be mounted to DIN-rail using the optional kit that is Omega part number IP610-DM.This will allow the transducer to mount to DIN 50045, 50035, 50022 rails (See figure 3).Figure 3-DIN Rail mounting kit IP610-DMShaded areas and associated dimensions apply to the zero based unit only.1.3.1Clean all pipe lines to remove dirt and scale prior to installation.1.3.2Supply air must be filtered to 40 microns and free of moisture and lubricants.1.3.3Two (2) 1/4” NPT ports are provided for supply air connections. Either port may be used. The unused port must be plugged with the pipe plug included with the unit.1.3.4Two (2) 1/4” NPT ports are provided for pneumatic output connections. Either port may be used and one may beused for the mounting of an output gauge. If no gauge is installed, the unused port must be plugged with the pipe plug included with the unit.1.4 Electrical Connections1.4.1The I/P versions of the IP610 are two wire devices (do not require a separate power source), plus a safety ground.The I/P unit requires a variable input current of 4-20 mA.1.4.21/2” NPT conduit connection (A) is made using 18” pigtail wire coming from unit. For I/P (current to pressure)versions, electrical connections are made to the red (+) and black (-) leads. The green lead is furnished for caseground.Figure 4 - 1/2” Conduit ConnectionI/P Conduit Connection1.4.3DIN43650 Connector (D)electrical connections are made as shown in figure 5.Figure 5 - DIN 43650 ConnectionsShaded areas and associated dimensions apply to the zero based unit only.1.5 Factory Mutual Research Corporation (FM)and Canadian Standards association (CSA)Notes:1. Control equipment connected to the Associated Apparatus must not use or generate more than 250 Vrms or Vdc.2. The IS Barriers or Equipment (Associated Apparatus) must be FM Approved and CSA Certified and theconfiguration of Associated Apparatus must be FM Approved and CSA Certified under the Entity Concept. The Associated Apparatus may be installed within the Hazardous (Classified) location for which it is certified. The Associated Apparatus and hazardous location loop apparatus manufacturer’s control drawings must be followed when installing this equipment. An AEx [ib] Associated Apparatus is suitable only for connection to Class I, Zone 1, Hazardous (Classified) Locations and is not suitable for Class I, Zone 0, or Class I, Division 1 Hazardous (Classified) Locations.3. Installation should be in accordance with ANSI/ISA RP12.06.01 “Installation of Instrinsically Safe Systems for Hazardous (Classified) Locations” and Article 500 of the National Electrical Code (ANSI/NFPA 70) and Section 18of the Canadian Electrical Code.4. The standard conduit is suitable for Type 4X installations. All others must be mounted in a suitable enclosure.5.The standard conduit is suitable for Class I, II and III, Division 2, Groups A, B, C, D, F & G hazardous (classified)locations. Dust-tight conduit seal must be used when installed in Class II and Class III environments.The connection option “D” is suitable for Class I, Division 2, Groups A, B, C and D hazardous (classified) locations.Transducers to be installed in accordance with National Electrical Code (ANSI/NFPA 70) Division 2 hazardous (classified) location wiring techniques and the Canadian Electrical Code.6. The Instrinsic Safety Entity concept allows the interconnection of two FM Approved or CSA Certified intrinsically safe devices with entity parameters not specifically examined in combination as a system when:Ui or Vmax >Uo or Vocli or Imax > lo or lsc or ItCa or Co > Ci + CcableLa or Lo > Li + LcablePi > Po.7. No revision to this drawing is permitted without prior FM Approval/CSA Certification.Entity Parameters for Models IP610–*Ui (Vmax) = 30 V Ii (Imax) = 125 mA Ci = 0 uF Li = 0 mHPi = 0.7 wattsIntrinsically SafeClass I, II, III, Div. 1,Groups C, D, E, F & GModels IP610–*Class I, Div. 1, Groups C & DModels IP610–*Suitable for:Class I, Div. 2, Groups A, B, C & D Models IP610–*IP610–*Suitable for:Class II & III, Div. 2, Groups F & G Models IP610–**= Ouput pressure option does not affect ratingUnder normal circumstances, no maintenance should be required.3.1 Instrument Air Filtration3.1.1Failures due to instrument supply air contamination are not covered by warranty.3.1.2Use of oil and/or water saturated instrument air can cause erratic operation.3.1.3Poor quality instrument air can result in unit failure. It is recommended that a filter regulator be placed upstreamof each unit where oil and/or water laden instrument air is suspected.3.1.4If clean, dry air is not used the orifice can become blocked. To clean, first turn off supply air, then remove thescrew located on the side of the unit above the “out” port. Unplug the orifice using a wire that has a smallerdiameter than 0.012” (0.30mm). Replace screw tightly into unit.PROBLEM LOOK FOR SOLUTIONNo or low output Zero adjustment Reset zero (2.2.3)Supply pressure too low Increase supply pressure (see specs) Unstable/low output Electrical connection Check connection/signal (1.1.2)Clogged orifice Clean orifice (3.1.4) Erratic operation Liquid/contamination in air supply Clean air supply (1.1.3)Works in reverse Pressure goes down when Reverse input wires (1.4.2)signal is increasedOutput equals supply pressure Improper pneumatic connections Insure that supply is connected to“IN” port and output is connected to“OUT” port(1.3.3, 1.3.4)These products are intended for use in industrial compressed-air systems only.Do not use these products where pressures and temperatures can exceed thoselisted under Specifications.Before using these products with fluids other than air, for non-industrial application, life-support systems, or other applications not within published specifications, consult Omega Engineering Inc.Page 8。

目录一、TCR-610型收卡器技术说明 (3)1.1概述 (3)1.2功能简述： (3)1.3适用卡片材料 (3)1.4收卡器净重 (3)1.5收卡时间 (3)1.6直流特性 (3)1.7环境特性 (3)1.8控制接口描述 (4)1.8.1接口定义 (4)1.8.2控制信号说明 (4)1.8.3接口电路示意图 (5)1.8.4．RS232接口 (5)1．9E ASY SDPP V ER1.00通讯协议 (6)1.9.1．简介 (6)1.9.2．物理层描述 (6)1.9.3．传送层 (6)1.9.4．收卡机的Slave ID号 (7)1.9.5．收卡机的通讯命令与应答 (7)1.10等待命令超时自动退卡设置 (9)1．11阻塞或超时自动退卡设置 (9)1．12退卡后再收卡时间设置 (9)1.13收卡器的工作状态指示 (9)二、安全和保养 (10)三、保修细则 (11)一、TCR-610型收卡器技术说明1.1 概述TCR-610型收卡器选用高强度非金属防腐材料，按工业级标准设计、生产。

主要用于智能停车收费系统和通道闸自动收票系统。

在IC卡系统使用其读卡可靠性有较大提升。

该收卡器预留了读卡天线安装位置，具有选择退卡和超时退卡的功能，并具有防止误收、跟卡功能。

1.2功能简述：1）发生堵塞时可以选择超时退卡或超时不退卡，以及强制收卡或退卡。

2）当卡片识别动作超时，可选择超时退卡或超时不退卡。

3）可以选择卡片识别动作超时退卡时间。

4）具有防止误收跟卡功能：当收第一张卡动作未完成时，插入第二张卡，会使收卡动作停止，拔出第二张卡，才会继续收第一张卡。

5）可为上位机提供使能和开闸等信号。

6）可以接收上位机的卡有效、无效等命令。

7）错误状态声光报警。

8）具有RS232通讯功能，协议兼容TCR-400S。

1.3 适用卡片材料纸质卡片或聚脂类卡片.1.4 收卡器净重约0.7Kg1.5 收卡时间大约2秒1.6 直流特性额定电压：24V DC ±10%峰值电流： 1.8 Amp静态电流：0.1 Amp1.7 环境特性温度：-40℃to 85℃（工业级）湿度：30-90% （相对湿度）使用条件：安装在箱柜中使用1.8 控制接口描述TCR-610收卡器提供TTL电平控制接口和串行通信控制接口，TTL电平控制接口由控制板上插座J7引出，串行通信控制接口由控制板上插座J3引出，联接插座均采用市面极易采购的间距为2.54mm标准接插件。

系‎统的考虑，‎按照道理来‎说应该是所‎有的lin‎u x系统都‎能安装运行‎i c610‎的，只不过‎因为各个l‎i nux组‎件实现不完‎全统一，所‎以在安装i‎c610的‎时候会出现‎各种问题，‎但是只要你‎有相关li‎n ux系统‎的知识，对‎于linu‎x一些基本‎设计理念比‎较熟悉的话‎，应该都是‎可以通过调‎整系统来安‎装运行ic‎610的。

‎安装ic6‎10的过程‎实际上就是‎一个根据c‎a denc‎e给出的错‎误信息进行‎d ebug‎的过程，你‎把所有的b‎u g都解决‎了，软件也‎就自然能运‎行了。

‎现‎在已知可以‎运行ic6‎10的系统‎r ehl，‎c ento‎s，sus‎e，ubu‎n tu还有‎a rchl‎i nux（‎我作证，呵‎呵）。

推荐‎使用的系统‎是rehl‎或是cen‎t os，这‎两个应该是‎兼容性最好‎的，当然下‎面的安装过‎程还是以a‎r chli‎n ux为例‎来讲解的。

‎1 确‎认所用li‎n ux系统‎的tar版‎本在1.1‎4以下，否‎则不能正常‎解压安装包‎。

---‎-这一步基‎本废话，因‎为现在找的‎包应该是重‎新用高版本‎的tar打‎包过的，所‎以直接进行‎下面的就行‎了。

2‎下载安装‎包，包括：‎B ase_‎I C610‎_lnx8‎6_1of‎5.tar‎- Bas‎e_IC6‎10_ln‎x86_5‎o f5.t‎a r 五个‎t ar包，‎B ase_‎M MSIM‎61_ln‎x86_1‎o f2.t‎a r和Ba‎s e_MM‎S IM61‎_lnx8‎6_2of‎2.tar‎两个tar‎包，全部解‎压缩，将得‎到的IC6‎10 cd‎1-cd5‎放在一个文‎件夹内，如‎/inst‎a ll/i‎c610，‎将MMSI‎M的cd1‎和cd2放‎在另一个文‎件夹内，如‎/inst‎a ll/m‎m sim。

‎----‎注意当然还‎要有ic6‎10的li‎c ense‎了。

IC-9110W包裝內容網路線安裝指南電源變壓器室外型攝影機雙面泡棉膠帶壁架定位輔助圖室內連線主機攝影機組裝螺絲室內連線主機組裝螺絲CD 光碟片攝影機天線LED指示燈號說明LED燈號LED 燈色狀態敘述電源指示燈綠色燈亮本產品已啟動並已連接到雲端伺服器快速閃爍本產品正在重新啟動中慢速閃爍(約每秒閃1次)本產品正在啟動中或尚未連線到雲端伺服器LAN指示燈綠色燈亮本產品已連接到區域網路快速閃爍表示有資料透過有線網路傳輸中。

慢速閃爍(約每秒閃1次)WPS功能已啟動Internet 橘色燈亮已連接到網際網路慢速閃爍(約每秒閃1次)未連接到網際網路硬體安裝建議您在將本產品安裝至戶外據點前，請先建立有效的網路連線，並且如下所示安裝本產品。

您可以在室內連線主機的背面標籤貼紙上找到產品獨有的 SSID，它會標示如"EdiView.Setup**"，最後兩碼* * 即為您的網路攝影機MAC 位址的最後兩碼。

1.請先將天線裝上室內連線主機的天線連接埠。

2.再將攝影機的連接線插入室內連線主機的連接埠(與天線接埠同側)。

3. 將電源變壓器(如下圖示)接入室內連線主機的電源接埠並插入電源插座。

4. 請稍待室內連線主機開機完成。

當它開機完成時，綠色的電源LED 燈號會呈現慢速閃爍的狀態。

5. 請使用手機或平板，至Apple App Store 或Google Play 搜尋"EdiView II " 或〝 EdiLife 〞app ，然後下載並安裝。

下圖及以下說明為EdiView II6.啟動 EdiView II App之前，iOS用戶請先前往您iPhone(或iPad)的Wi-Fi設定，並連接到本產品的SSID，接著請前往步驟87.Android用戶請確認您Android 裝置的 Wi-Fi 已打開，並啟動EdiView II app。

選擇您的網路攝影機(如下所示)，然後按"OK"確定繼續，EdiView II 將連接到您的網路攝影機，請稍等片刻。