LED节能灯说明书

Led 灯简易使用说明书
一、 后面板图解说明
菜单 减键 加键 却换/进入 操作说明：
1、 按菜单键可在’IMAGE ’、’DMX ’、’STAT ’、’RUN ’、’AUTO ’、’TEMP ’、’VOX ’、
‘MODE ’8个菜单中选择；
2、 按却换/进入键可以进入相应菜单的子项，且有多个子项时按此键进行子项
之间的却换；
3、 减键和加键进行数值的加减和功能的设置；
4、 在参数设置好后，按菜单键退出此菜单并将参数记忆；
二、 Led 显示功能对照表
三、Dmx512通道说明3通道：
6通道：
9通道：
四、技术指标
1、工作电压：AC220v 50Hz
2、最大功率：<200W
3、亮度：3m距离>3500 CD
4、颜色：R 控制等级0—255
G 控制等级0—255
B 控制等级0—255
W 控制等级0—255
5、频闪：控制等级11——255
6、灯杯角度：15度、30度、45度可选
7、温升：<40度
8、灯体可调角度：>180度
长沙新画佳光电子有限公司
2010-2-8。

Philips EssentialLED Bulb 3000K/6500K 230VPhilips Essential LED Bulb is a sustainable green light bulb to ensure direct replacement of GLS bulbs in indoor application.With latest LED technology, Essential LED Bulb o ers over 83% energy saving and lasts 10 years (if lit 2.7 hours per day across 365 days) to save your total investment cost.From LED chips chosen to the nal assembly, di erent kinds of professional quality control methods are adopted to guarantee the light quality consistency through product lifetime.The product is professionally designed to endure surge and environmental tests to make sure it can be adapted into di erent indoor application situations.Design highlights• Form factor is designed as a direct retrofit into A60 fixtures • Over 85% energy-saving compared with GLS• Long lifetime of 10 years (if lit 2.7 hours per day across 365 days)• Warm white CCT 3000K and cool daylight CCT 6500K available • Environmental friendly, no Mercury or any other hazardous substances • Low Carbon FootprintApplication areasApplication notes• Operating temperature range is between -20 °C and 45 °C ambient• Only to apply in dry or damp locations and most of open fixtures with E27/B22 lamp- holders that offer sufficient space (10 mm free air space)• Not intended for use with emergency light fixtures or exit lights • Not intended for enclosed luminaires The qualified light makes it suitable for general indoor applications such as:• Elite shops• Corridors / Stairways / Washrooms • Lobby / Reception areas • Hotel rooms / Bars• HomeProduct type Voltage Wattage Cap Bulb CCT Lumen Luminous Lifetime CRI EEIshape e cacy label(V) (W) (K) (Lm) (=lm/W) (hours)ESS LEDBulb 4W E27 3000K 230V A60 TR 220-240V 4.0 E27 A60 3000 300 75 10000 80 A+ ESS LEDBulb 4W E27 6500K 230V A60 TR 220-240V 4.0 E27 A60 6500 310 78 10000 80 A+ ESS LEDBulb 6W E27 3000K 230V A60 TR 220-240V 6.0 E27 A60 3000 490 82 10000 80 A+ ESS LEDBulb 6W E27 6500K 230V A60 TR 220-240V 6.0 E27 A60 6500 510 85 10000 80 A+ ESS LEDBulb 8W E27 3000K 230V A60 TR 220-240V 8.0 E27 A60 3000 610 76 10000 80 A+ ESS LEDBulb 8W E27 6500K 230V A60 TR 220-240V 8.0 E27 A60 6500 640 80 10000 80 A+ ESS LEDBulb 4W E27 3000K 230V A60 UAE 220-240V 4.0 E27 A60 3000 300 75 10000 80 4 star ESS LEDBulb 4W E27 6500K 230V A60 UAE 220-240V 4.0 E27 A60 6500 310 78 10000 80 4 star ESS LEDBulb 6W E27 3000K 230V A60 UAE 220-240V 6.0 E27 A60 3000 490 82 10000 80 4 star ESS LEDBulb 6W E27 6500K 230V A60 UAE 220-240V 6.0 E27 A60 6500 510 85 10000 80 4 star ESS LEDBulb 8W E27 3000K 230V A60 UAE 220-240V 8.0 E27 A60 3000 610 76 10000 80 4 star ESS LEDBulb 8W E27 6500K 230V A60 UAE 220-240V 8.0 E27 A60 6500 640 80 10000 80 4 star ESS LEDBulb 4W B22 3000K 230V A60 UAE 220-240V 4.0 B22 A60 3000 300 75 10000 80 4 star ESS LEDBulb 4W B22 6500K 230V A60 UAE 220-240V 4.0 B22 A60 6500 310 78 10000 80 4 star ESS LEDBulb 6W B22 3000K 230V A60 UAE 220-240V 6.0 B22 A60 3000 490 82 10000 80 4 star ESS LEDBulb 6W B22 6500K 230V A60 UAE 220-240V 6.0 B22 A60 6500 510 85 10000 80 4 star ESS LEDBulb 8W B22 3000K 230V A60 UAE 220-240V 8.0 B22 A60 3000 610 76 10000 80 4 star ESS LEDBulb 8W B22 6500K 230V A60 UAE 220-240V 8.0 B22 A60 6500 640 80 10000 80 4 star ESS LEDBulb 4W E27 3000K 230V A60 SA 220-240V 4.0 E27 A60 3000 300 75 10000 80 C ESS LEDBulb 4W E27 6500K 230V A60 SA 220-240V 4.0 E27 A60 6500 310 78 10000 80 C ESS LEDBulb 6W E27 3000K 230V A60 SA 220-240V 6.0 E27 A60 3000 490 82 10000 80 C ESS LEDBulb 6W E27 6500K 230V A60 SA 220-240V 6.0 E27 A60 6500 510 85 10000 80 C ESS LEDBulb 8W E27 3000K 230V A60 SA 220-240V 8.0 E27 A60 3000 610 76 10000 80 C ESS LEDBulb 8W E27 6500K 230V A60 SA 220-240V 8.0 E27 A60 6500 640 80 10000 80 C ESS LEDBulb 4W B22 3000K 230V A60 SA 220-240V 4.0 B22 A60 3000 300 75 10000 80 C ESS LEDBulb 4W B22 6500K 230V A60 SA 220-240V 4.0 B22 A60 6500 310 78 10000 80 C ESS LEDBulb 6W B22 3000K 230V A60 SA 220-240V 6.0 B22 A60 3000 490 82 10000 80 C ESS LEDBulb 6W B22 6500K 230V A60 SA 220-240V 6.0 B22 A60 6500 510 85 10000 80 C ESS LEDBulb 8W B22 3000K 230V A60 SA 220-240V 8.0 B22 A60 3000 610 76 10000 80 C ESS LEDBulb 8W B22 6500K 230V A60 SA 220-240V 8.0 B22 A60 6500 640 80 10000 80 CLEDbulbB22E27Spectral Power DistributionSpectrum Essential LED Bulb 3000KTemperature300/310lm T c Max: 102 o C 490/510lm T c Max: 90 o C610/640lm T c Max: 105 o CTc pointSpectrum Essential LED Bulb 6500KEssential LEDBulb 4W E27/B22 3000K 230V A601 x 300 lmLight output ratio 1.00Service upward 0.81Service downward 0.19CIE ux code7 26 56 19 100UGRcen (4Hx8H, 0.25H )16Essential LEDBulb 4W E27/B22 6500K 230V A601 x 310 lmLight output ratio 1.00Service upward 0.81Service downward 0.19CIE ux code7 26 56 19 100UGRcen (4Hx8H, 0.25H )16Essential LEDBulb 6W E27/B22 3000K 230V A601 x 490 lmLight output ratio 1.00Service upward 0.81Service downward 0.19CIE ux code7 26 56 19 100UGRcen (4Hx8H, 0.25H )17Light output ratio 1.00Service upward 0.81Service downward 0.19CIE ux code7 26 56 19 100UGRcen (4Hx8H, 0.25H )18Essential LEDBulb 6W E27/B22 6500K 230V A601 x 510 lmLight output ratio 1.00Service upward 0.81Service downward 0.19CIE ux code7 26 56 19 100UGRcen (4Hx8H, 0.25H )18Light output ratio 1.00Service upward 0.81Service downward 0.19CIE ux code7 26 56 19 100UGRcen (4Hx8H, 0.25H )18Essential LEDBulb 8W E27/B22 3000K 230V A601 x 610 lmEssential LEDBulb 8W E27/B22 6500K 230V A601 x 640 lmLifetime + SustainabilityFailure Rate Curve of Essential LED bulb 3000K/6500K50%45%40%35%30%25%20%15%10%5%0%500010000T o t a l F a i l u r e R a t eHoursEssential LED Bulb has a lifetime exceeding 10,000 hours de ned as (F50L70), where:F50L70, meaning 50% in total of whole population of lamps either fail without light output or lumen maintenance lower than 70% of initial value.Lifetime estimation based on the application environment condition: at room temperature (25°C), free air burning,baseup burning position, and at rated voltage.© 2016 Philips LightingAll rights reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent or other industrial or intellectual property rights.。

Part NumberEmitting Color (Material)Lens TypeIv (mcd) @ 20mA [2] Viewing Angle [1]Min. Typ. 2θ1/2L-7104PBC-A■ Blue (InGaN)Water Clear 400 30°900DESCRIPTIONSzThe Blue source color devices are made with InGaN on SiC Light Emitting Diodez Electrostatic discharge and power surge could damage the LEDsz It is recommended to use a wrist band oranti-electrostatic glove when handling the LEDs z All devices, equipments and machineries must be electrically groundedFEATURESzLow power consumptionz Popular T-1 diameter package z General purpose leads z Reliable and ruggedz Long life - solid state reliability z Available on tape and reel z RoHS compliantAPPLICATIONSz Status indicator z Illuminatorz Signage applicationsz Decorative and entertainment lightingzCommercial and residential architectural lightingATTENTIONObserve precautions for handlingelectrostatic discharge sensitive devicesPACKAGE DIMENSIONSL-7104PBC-AT-1 (3mm) Solid State LampSELECTION GUIDENotes:1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value.2. Luminous intensity / luminous flux: +/-15%.3. Luminous intensity value is traceable to CIE127-2007 standards.Notes:1. All dimensions are in millimeters (inches).2. Tolerance is ±0.25(0.01") unless otherwise noted.3. Lead spacing is measured where the leads emerge from the package.4. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.ABSOLUTE MAXIMUM RATINGS at T A =25°CELECTRICAL / OPTICAL CHARACTERISTICS at T A =25°CNotes:1. 1/10 Duty Cycle, 0.1ms Pulse Width.2. 2mm below package base.3. 5mm below package base.4. Relative humidity levels maintained between 40% and 60% in production area are recommended to avoid the build-up of static electricity – Ref JEDEC/JESD625-A and JEDEC/J-STD-033.Notes:1. The dominant wavelength (λd) above is the setup value of the sorting machine. (Tolerance λd : ±1nm. )2. Forward voltage: ±0.1V.3. Wavelength value is traceable to CIE127-2007 standards.4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or premature failure.ParameterSymbol Value Unit Power Dissipation P D 120 mW Reverse Voltage V R 5 V Junction Temperature T j 125 °C Operating Temperature T op -40 to +85 °C Storage Temperature T stg -40 to +85°C DC Forward Current I F 30 mA Peak Forward CurrentI FM [1]100 mA Electrostatic Discharge Threshold (HBM) -1000VLead Solder Temperature [2] 260°C For 3 Seconds Lead Solder Temperature [3]260°C For 5 SecondsParameterSymbol Emitting ColorValue Unit Typ. Max. Wavelength at Peak Emission I F = 20mA λpeak Blue 468 - nm Dominant Wavelength I F = 20mA λdom [1] Blue 465 - nm Spectral Bandwidth at 50% Φ REL MAX I F = 20mA Δλ Blue 21 - nm CapacitanceC Blue 100 - pF Forward Voltage I F = 20mA V F [2] Blue 3.2 4 V Reverse Current (V R = 5V)I RBlue-10uATECHNICAL DATABLUERECOMMENDED WAVE SOLDERING PROFILENotes:1. Recommend pre-heat temperature of 105°C or less (as measured with a thermocoupleattached to the LED pins) prior to immersion in the solder wave with a maximum solder bath temperature of 260°C2. Peak wave soldering temperature between 245°C ~ 255°C for 3 sec (5 sec max).3. Do not apply stress to the epoxy resin while the temperature is above 85°C.4. Fixtures should not incur stress on the component when mounting and during soldering process.5. SAC 305 solder alloy is recommended.6. No more than one wave soldering pass.PACKING & LABEL SPECIFICATIONSPRECAUTIONSStorage conditions1. Avoid continued exposure to the condensing moisture environment and keep the product away from rapid transitions in ambient temperature.2. LEDs should be stored with temperature ≤ 30°C and relative humidity < 60%.3. Product in the original sealed package is recommended to be assembled within 72 hours of opening. Product in opened package for more than a week should be baked for 30 (+10/-0) hours at 85 ~ 100°C.2. When soldering wires to the LED, each wire joint should be separately insulated with heat-shrink tube to prevent short-circuit contact. Do not bundle both wires in one heat shrink tube to avoid pinching the LED leads. Pinching stress on the LED leads may damage the internal structures and cause failure.3. Use stand-offs (Fig.1) or spacers (Fig.2) to securely position the LED above the PCB.4. Maintain a minimum of 3mm clearance between the base of the LED lens and the first lead bend (Fig. 3 ,Fig. 4).5. During lead forming, use tools or jigs to hold the leads securely so that the bending force will not be transmitted to the LED lens and its internal structures. Do not perform lead forming once the component has been mounted onto the PCB. (Fig. 5 )LED Mounting Method1. The lead pitch of the LED must match the pitch of the mounting holes on the PCB during component placement.Lead-forming may be required to insure the lead pitch matches the hole pitch.Refer to the figure below for proper lead forming procedures.Note 1-3: Do not route PCB trace in the contact area between the leadframe and the PCB to prevent short-circuits." ○" Correct mounting method " x " Incorrect mounting methodLead Forming Procedures1. Do not bend the leads more than twice. (Fig. 6 )2. During soldering, component covers and holders should leaveclearance to avoid placing damaging stress on the LED duringsoldering.(Fig. 7)3. The tip of the soldering iron should never touch the lens epoxy.4. Through-hole LEDs are incompatible with reflow soldering.5. If the LED will undergo multiple soldering passes or face otherprocesses where the part may be subjected to intense heat,please check with Kingbright for compatibility.PRECAUTIONARY NOTES1. The information included in this document reflects representative usage scenarios and is intended for technical reference only.2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer tothe latest datasheet for the updated specifications.3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. Ifcustomer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues.4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threateningliabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance.5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright.6. All design applications should refer to Kingbright application notes available at /application_notes。

LED灯产品说明书
一、产品概述
LED灯是一种高效、环保、节能的照明产品，采用最新的LED技术，具有长寿命、低能耗、高亮度等优点。

本产品适用于家庭、办公室、商场、酒店等场所的照明需求。

二、产品特点
1.长寿命：LED灯的使用寿命长达5万小时以上，比传统白炽灯和荧光灯更耐用。

2.低能耗：LED灯的能耗仅为传统白炽灯的1/10，具有极高的节能效果。

3.高亮度：LED灯的亮度比传统白炽灯更高，能够提供更明亮的照明效果。

4.环保：LED灯不含有害物质，对环境和人体健康无害。

5.易于安装：LED灯采用标准接口，可以方便地安装到各种灯具上。

三、使用方法
1.安装：请按照说明书中的步骤正确安装LED灯，确保电源连接稳定。

2.使用：打开电源开关，LED灯即可正常工作。

可以根据需要调节亮度。

3.维护：定期清理灯具表面灰尘，保持灯具清洁。

如遇故障，请联系专业维修人员。

四、注意事项
1.请勿在潮湿环境下使用LED灯。

2.请勿在高温环境下长时间使用LED灯。

3.请勿在电源不稳定的环境下使用LED灯。

4.请勿拆卸或自行维修LED灯。

五、售后服务
本产品自购买之日起享受一年质保服务。

如有质量问题或使用不当导致的损坏，可凭购买凭证免费维修或更换。

LED lighting for hazardous areas Champ VMVL EMChamp VMVL LED with emergency back-up batteryCertifications and compliances:NEC & CEC• Class I, Division 2, Groups A, B, C, D • Class II, Division 1, Groups E, F , G • Class III • Class I, Zone 2• Simultaneous Presence •Wet Locations, Type 4X, IP66UL standards• UL 844 Hazardous (Classified)• UL1598 Luminaires, UL1598A Marine •UL924 (Emergency Luminaire)CSA standard•CSA C22.2 No. 137Lighting and back-up power is critical to any safety plan. That's why we've expanded our offering to include the Champ VMVL EM LED luminaire with an integrated battery backup.In the event of power loss or power interruption, Champ ® VMVL LED with built-in back-up powerprovides 90 minutes of emergency lighting to help keep your people safe and your plant running smoothly.Designed for maintenance-free illumination in egress and emergency lighting areas, the Champ VMVL is rated for indoor and outdoor emergency lighting in hazardous locations, such as manufacturing plants, heavy industrial, chemical, petrochemical facilities, platforms, loading docks and parking areas.VMVL -3 to 7VMVL -9 &11T emperature codes:All models –THDCurrent draw: 120-277 VAC Input power NominalBattery EM Battery EMElectrical ratings:*Maximum AC power draw by the charge controller is 4 Watts WeightEaton is a registered trademark.All other trademarks are property of their respective owners.Eaton’s Crouse-Hinds 1201 Wolf Street Syracuse, NY © 2022 EatonAll Rights Reserved Printed in USAPublication No. 5461-0322March 2022Ordering information20A20mm pendant3C1” ceiling25TW25mm wallAccessories(ordered separately)P3002Wire guardREPLACEMENT KITReplacement EM driver*Consult factory for lead time*Available with ceiling mounted modules only.Part number example: VMVL -3-W-2A-G-UNV1-EM1VMVL Champ VMVL, 3,000 lumens, 4000K warm white, ¾" pendant mount, Type V optics, wire guard, 100-277 VAC driver, emergency driver system, clear glass lens/ChampDimensions:。

太阳能LED灯具使用说明书一、概述太阳能LED灯具由控制柜、太阳能电池、LED球泡灯组成,如下图所示，太阳能电池将光能转化电能对控制器内部蓄电池充电。

太阳能LED灯具工作在两种状态：①充电状态；②开灯状态。

二、电参数太阳能电池最大输入电压：DC 17V；输出电压：DC 12V；工作环境温度：-25～60℃。

三、功能说明太阳能电池平稳放于日照处，用于充分吸收外界光能。

充电状态:太阳能电池与控制柜连接好后按下AN1开关，外界光照足够强时，此时太阳能电源指示灯亮，蓄电池充电指示灯HL1慢闪烁，此时蓄电池正在充电。

开灯状态:闭合S1开关，1路输出LED球泡灯亮同时HL2输出指示灯也亮。

闭合S2开关，2路输出LED球泡灯亮同时HL2输出指示灯也亮。

四、控制柜结构尺寸五、产品包装1．检验合格的产品用塑料袋封装后放入箱内，并衬以防震材料，防止运输过程中发生窜动或碰撞。

2．产品包装能满足防潮、防尘的要求。

包装箱外表面标有产品名称、型号规格、生产批号、数量、净重、制造厂家等，还标有防潮、防震、小心轻放、切勿倒置等字样或图案标志。

六、设备附件七、产品维护敬告：在进行产品维护时，请确保断电操作，以免发生意外触电，请参照以下要求和方法进行日常维护和定期检修，对于已损坏设备请及时寄回我公司进行维修。

1. 日常维护定期检查系统控制器各紧固件，确保不会脱落影响设备正常运行。

保持清洁，注意防潮。

如发现故障，请作好记录以待维修。

2. 故障分析及维修说明：因系统单元较简单，一般性故障可在现场检修处理，如有个别疑难故障无法排除，可联系相关人员进行帮助检修，排除故障。

（1）无法进充电或点亮如因特殊原因，系统不能正常启动或无法进充电或点亮，请先确认外线路是否正常，如太阳能板连接线是否有短路等；在确认外线路正常后，打开系统控制器检查内部各接插件是否有脱落松动或接触不良等现象。

如确认连接正常还无法排除故障，可联系我公司相关人员进行更换。

八、售后服务在用户正确安装、操作及符合本手册要求使用条件下，在质保期内，如出现因产品质量不良而发生故障时，此故障仅限于功能性故障，如完全无法点亮或充电等，我公司将为用户提供维修或更换服务。

L E D灯具使用说明书警告：
为了使灯具安装正确,开箱后请详细阅读本说明书,并妥善保管
一、灯具主要结构和适用范围
1.壳体均采用铝合金材料制成,表面抛光拉丝及静电氧化处理,恒温固化,附着力强,具有防水、防尘、结构新颖等特点.
2.主要适用于办公场所,商场共公场所作照明.
二、主要结构参数
1.：85--265V~50/60Hz
2. ：30W□60W□90W□120W□140W□160W□
3.防触电保护等级：I类
4.外壳防护等级：IP65
5.LED颗数：
6.产品尺寸
7.光通量:90LM/W□100LM/W□110LM/W
8.发光角度;60°□90°□120°□
9.使用环境:温度:≥90%;工作温度:-40℃~+55℃
三、安装要求及维护
1、首先整理灯具配套用(de)各种零部件和附件.
2、安装前必须先切断电源.
3、如使用本产品更换普通灯具,请仔细检查产品接口与旧灯座(de)符合性,切勿误用.
4、把灯体所带(de)电线连接在相配(de)电源线上.
5、确定本产品紧固在被安装物表面在进行以下操作,最后接通电源点亮.
四、注意事项
◆未按照说明书操作可能会有危险.
◆违章操作可能损坏你(de)物品,甚至会危害到您(de)人身安全.。

IP20Product luminaires comply with EN60598-2-22 and are suitable for use in normal interior conditionso oThis luminaire has an ambient temperature range of 5C to 25COnce installed in the ceiling, the luminaire face is rated IP20Safe Operation1. Check the rating label for voltage and frequency before connecting this luminaire to the electrical supply.2. Ensure that the mains supply is switched off when working on this luminaire, whether installing or carrying out any other servicing.3. Do not mount luminaire on or close to readily flammable materials.4. To prevent damage to driver, do not mix with conventional magnetic ballasts on the same electrical circuit.5. Where use in more onerous situations is required, e.g. In part-completed buildings before “drying-out” is completed, or areas where ambient temperatures are outside the normal temperature range, then consult our Sales Office.6. This product must only be installed in locations where accidental disconnection of the head interconenction lead is not possible.or battery connection lead Servicing and Disposal1. At commissioning and handing over of installation ensure that a copy of these instructions is presented to the authority responsible for the operation and maintenance of the luminaries.2. Servicing, e.g. cleaning, must only be carried out after the electricity supply has been switched off. It must not be assumed that luminaries with lamps not lit are switched off-always check before servicing.3. Cleaning should be carried out at regular intervals to ensure that dirt does not accumulate to an extent that will impair the thermal safety or optical performance of the luminaire. Regular cleaning will also ensure that the optical performance of the luminaries is maintained.4. Avoid touching the LED array surface. To clean - Blow surface with either dry air or nitrogen gas.5. At the end of life the luminaire is classed as WEEE under directive 2002/96/EC and should be disposed of in accordance with local legislation.Note: The LED’s are non-replaceable but the batteries can be replaced by a competent personLuminaire CleaningEnd of Life and Components Disposal。

LED产品技术说明书范文样本1.概述本产品为LED-901充电式手电筒，公司遵循国家行业执行标准：GB7000.13-1999，确属本公司产品质量问题，自购置之日起保修期为3个(非正常使用而致使产品损坏，烧坏的，不属保修之列。

)2.技术特性●本产品额定容量高达900mAH。

●超长寿命电池，高达500次以上循环使用。

●采用节能，高功率，超长寿命的LED灯泡。

●充电保护:充电状态显示红灯，充电满显示绿灯。

3.工作原理LED灯由电池提供电源而发光，此电池充电后可重复使用。

4.结构特性：(略)6.使用和操作●充电时灯头应朝下，将手电筒交流插头完全推出，直接插入AC110V/220V电源插座上，此时红灯亮起，表示手电筒处于充电状态;当充电充满时，绿灯亮起，表示充电已充满。

●使用时推动开关按键，前档为6个LED灯亮，中间档为3个LED灯亮，后档为关灯。

●充满电，3个LED灯可连续使用约26个小时，6个LED灯可连续使用16个小时7.故障分析与排除①使用过程中若发现灯不亮或者光线很暗，则有可能是电池电量不足，如果充电后灯变亮则说明手电筒功能正常，如果充电后仍然不亮，则有可能是线路故障，可以到本公司自费维修。

②使用几年后若发现充电后灯不亮，则极有可能是电池寿命已到，应及时到本公司自费更换。

8.维修和保养●在使用过程中，如LED灯泡亮度变暗时，电池处于完全放电状态，为保护电池，应停止使用，并及时充电(不应在LED灯泡无光时才充电，否则电池极易损坏失效。

)●手电筒应该经常充电使用，请勿长期搁置，如不经常使用，请在存放2个月内补充电一次，否则会降低电池寿命9.注意事项●请选择优质插座，并保持安全规范充电操作。

●产品充电时切勿使用，以免烧坏LED灯泡或电源内部充电部件。

●手电筒不要直射眼睛，以免影响视力。

(小孩应在大人指导下使用。

)●勿让本产品淋雨或者受潮。

●当充电充满时(绿灯亮起)，请立即停止充电，避免烧坏电池。

●非专业人士请勿随便拆卸手电筒，避免引起充电时危险。