BZBD使用手册版

道路运输车辆卫星定位系统车载终端用户手册V1.0目录V1.0 (1)目录 (1)产品概述 (3)技术指标 (4)功能详细介绍 (6)3.1查询功能 (6)3.1.1位置查询（支持SMS模式） (6)3.1.2参数状态查询（支持SMS模式） (6)3.1.3定时回传参数查询（支持SMS模式） (6)3.1.4查询车辆历史轨迹 (6)3.1.5查询车辆参数 (6)3.1.6版本查询（支持SMS模式） (6)3.2设置 (6)3.2.1定时回传位置信息的时间间隔设置（支持SMS模式） (6)3.2.2超速报警门阀设置（支持SMS模式） (7)3.2.3停车超时报警门阀设置（支持SMS模式） (7)3.2.4电子围栏设置（支持SMS模式） (7)3.2.5多边形电子围栏设置（支持SMS模式） (7)3.2.6 IP、端口及APN设置（支持SMS模式） (7)3.2.7远程设置GPRS通讯方式（支持SMS模式） (7)3.2.8远程设置本机号（支持SMS模式） (7)3.2.9远程下载集团电话号码（支持SMS模式） (7)3.2.10通讯限制（支持SMS模式） (7)3.2.11远程修改短信中心号码（支持SMS模式） (8)3.2.12初始化里程（支持SMS模式） (8)3.2.13心跳时间设置（支持SMS模式） (8)3.2.14线路规划设置 (8)3.2.15车速传感器传递系数设置（支持SMS模式） (8)3.2.16车辆参数设置 (8)3.2.17自定义检测口配置 (8)3.3、远程控制 (8)3.3.1远程重启（支持SMS模式） (8)3.3.2远程控制油路（支持SMS模式） (9)3.3.3收发调度信息（支持SMS模式） (9)3.3.4远程监听（支持SMS模式） (9)3.3.5支持远程软件升级（支持SMS模式） (9)3.4报警 (9)3.4.1超速报警 (9)3.4.2停车超时报警 (9)3.4.3 GPS天线开路短路报警 (10)3.4.4终端主电源断电报警 (10)3.4.5电源过高/低报警 (10)3.4.6自定义报警（高低传感器报警） (10)3.4.7抢劫/求助报警 (10)3.4.8进出围栏报警 (10)3.4.9疲劳驾驶报警 (10)3.5其它 (10)3.5.1图像采集 (10)3.5.2定时拍照 (11)3.5.3触发拍照 (11)3.5.4里程统计 (11)3.5.5盲区补传 (11)3.5.6打印功能 (11)3.5.7行驶记录仪功能 (11)3.5.8、读取事故疑点数据 (11)四、外带接口和扩展功能 (11)4.1 带USB host接口 (11)4.2 DB9串口连接PC电脑 (12)4.3 无线红外接口 (12)4.4 带IC卡接口 (12)4.5 带速度传感器接口 (12)五、使用说明 (12)5.2主机参数设置 (13)5.2.1 菜单结构示意图： (14)5.2.2 菜单设置 (15)七安装及调试流程 (17)七包装清单 (18)八注意事项 (18)产品概述道路运输车辆卫星定位系统车载终端、符合汽车行驶记录仪国标GB/T GBT19056-2003和交通运输部JT/T 794-2011《道路运输车辆卫星定位系统车载终端技术要求》、JT/T808-2011《道路运输车辆卫星定位系统车载终端通讯协议及数据格式》标准。

济南三鼎电气有限责任公司JINANSANDINGELECTRICALCO,LTD. 直流转辙机限时保护器BXZ-BD1（BXZ-BJQ ）使用手册目录3.产品的介绍 (5)4.安装时的注意事项...............................................................9 5.维护和检查时的注意事项......................................................10 6.附录 (11)1.产品的确认与各部分名称●直流转辙机限时保护器型号 1、BXZ-BD1 ●各部分介绍限时保护器电路---用于直流转辙机转换不到位的限时保护。

表示变压器---用于提供道岔表示继电器的电源。

2、BXZ-BJQ 直流转辙机限时保护报警器●各部分介绍BXZ-BJQ直流转辙机限时保护报警器—用于当转辙机因故不能正常转换到位时，BXZ型保护器在限时切断转辙机动作电源的同时，通过报警输出端子送出报警信号，一台BXZ-BJQ型报警器可同时接收处理8路这种报警信息，并通过BXZ-Z型道岔监测装置总机显示具体报警信息，同时通过报警通道与微机监测系统通讯。

2.安装与接线●电源主机的供电电源是AC220V。

BXZ-BD1供电电源来自KZ24V、KF24V。

BXZ-BJQ供电电源来自KZ24V、KF24V。

●输出BXZ-BD1的输出有AC110V（13、23表示继电器电源）、限时输出（开关量31、33，用于直流转辙机转换不到位的限时保护）、报警输出（开关量51、53，用于直流转辙机转换不到位时，超过限时时间报警）BXZ-BJQ的输出主要是报警输出，把BXZ-BD1限时保护器的报警地址信息传送给主机。

●报警通道分机报警通道进与通道共分别与主机报警1通道的A4、A14相连，分机报警通道出与通道共分别与下一台分机报警通道进与通道共相连。

主机报警2、3、4通道与此接法同。

Z系列扩展BD板用户手册无锡信捷电气股份有限公司资料编号：ZC 02 20210406 3.5目录1. BD板的配置方法 (1)2. BD板精度与相关说明 (2)3. 模拟量输入输出扩展板Z-4AD2DA-A-BD (3)3-1.特点 (3)3-2.一般规格 (3)3-3.外部安装与接线 (3)3-4.输入输出定义号分配 (4)3-5.软件配置 (4)3-6.编程 (5)4. 模拟量温度扩展板Z-3AD3PT-BD (6)4-1.特点 (6)4-2.一般规格 (6)4-3.外部安装与接线 (6)4-4.输入输出定义号分配 (7)4-5.软件配置 (7)4-6.编程 (8)5. 称重扩展板Z-NWT-BD (9)5-1.特点 (9)5-2.一般规格 (9)5-3.外部安装与接线 (9)5-4.称重系统组成 (10)5-5.压力传感器介绍 (11)5-6.模数转换图 (11)5-7.输入定义号的分配 (11)5-8.模块设定 (12)5-9.编程 (13)6. 通讯扩展板Z-NES-BD (15)6-1.特点 (15)6-2.一般规格 (15)6-3.外部安装与接线 (15)6-4.软件配置 (16)7. I/O扩展BD板Z-NXMY-BD (21)7-1.特点 (21)7-2.模块规格 (21)7-2-1 型号说明 (21)7-2-2模块规格 (21)7-3.端子说明 (21)7-4.输入输出定义号分配 (22)7-5.外部安装与接线 (22)7-5-1. 扩展板的安装方法 (22)7-5-2. 输入规格及接线 (22)7-5-3. 输入电源规格 (23)7-5-4. 输出规格及接线 (23)7-6.软件配置 (24)8. 热电偶温度扩展板Z-4TC-BD (25)8-1.特点 (25)8-2.一般规格 (25)8-3.外部安装与接线 (25)8-4.输入输出定义号分配 (26)8-5.软件配置 (26)8-6.编程 (27)9. 编程举例 (28)1. BD 板的配置方法BD 板的配置方法：1）将BD 板正确安装到本体上，BD 板的配置位置如下所示：S/ N: N20140825028MODE: ZG3-30RXINJE2）然后，通过XDPPro 软件进行联机，首先在工程框内右击“PLC1”，然后选择“更改PLC 机型”，给PLC 选型号：ZG3-30，然后在左侧工程栏选择“PLC 配置”-“BD ”（如下图所示）：3）选择扩展BD 型号，并配置通道参数，设置完成后点击“确定”，然后下载程序，重新上电方可生效。

BDQC2D装车操作手册BDQC2D操作接口 (3)显示器 (3)键盘 (3)三种操作模式 (4)手动模式 (5)流水号模式 (7)ID卡模式 (10)装车过程 (12)启动前的参数检测 (13)启动装车的动作 (13)装车过程中的操作 (14)装车进行中 (14)接地报警 (15)溢出报警 (15)手动暂停 (16)远程暂停 (17)报警消除 (17)等候再启动 (18)等候退出 (19)提前量A到 (19)提前量B到 (20)低流速补发 (21)零流速报警 (22)阀门泄漏 (22)装车结束 (23)DI08连锁报警 (23)装车过程中AO的控制 (24)控制原理 (24)限速的原理 (25)简单操作范例 (25)手动装车 (25)流水号验证 (27)ID卡验证 (28)装车进行中的急停与继续 (29)提前结束本次装车 (30)装车结束的流程 (31)状态变化图 (33)手动操作流程 (34)自动操作流程 (35)BDQC2D操作接口BDQC2D对外的手动操作接口有两个，键盘、显示屏。

操作者通过显示屏观察BDQC2D 当前的状态，通过键盘进行操作。

BDQC-2D装车控制仪面板上有14个按键，1个点阵式显示器。

显示器点阵式显示器，有两种规格：VCF荧光式显示器和LCD液晶式显示器。

两种显示器的屏幕都使用64×128个显示点，正常情况下可以显示四行、每行16个英文字符或者8个汉字。

随着操作或者BDQC2D的自身状态变化，显示器会忠实的反应当前的状态并且不断的发生变化。

键盘BDQC2D的键盘包括0－9一共10个数字键以及小数点键、启动、确认、急停四个功能键。

数字键0的用途：在参数输入界面输入数字0在某些特定画面进行选择操作，如等候退出画面、等候启动画面数字键1的用途：在参数输入界面输入数字1在参数设置中进行菜单选择在某些特定画面进行选择操作，如等候退出画面、等候启动画面数字键2－9的用途在参数输入界面输入数字2－9在参数设置中进行菜单选择小数点键的用途在某些参数输入界面界面中输入小数点在一些参数查询画面中进行画面切换，如参数参看显示画面、历史记录查询画面等 在装车过程中切换当前显示的辅助参数确认键的用途在本地模式下进入参数设置菜单在参数输入界面中确认当前的输入在阀门泄漏状态下确认警告并且退出启动键的用途进入定量输入界面或者是流水号输入界面启动装车急停键的用途在参数界面中删除最后输入的数字直至退出输入界面在参数设置中退出当前的菜单在装车过程中进行急停操作在装车过程中退出当前的操作界面键盘操作的一个原则：当不知道该做什么事情又需要退出当前画面时，首先看第三行的提示，按照提示来操作；如果第三行没有提示，那么按“急停”，BDQC2D总会发生变化的。

目录文字说明1 概述2 结构与工作原理3 使用与操作4 维修5 地面实验附图图一BZ随钻震击器外形图及主要尺寸图二运行位置示意图图三新装间隔衬套修理尺寸图四调节震击力方向示意图产品总图BZ型随钻震击器使用说明书1．概述BZ（北震）型机械式随钻震击器是全机械式随钻震击、解卡工具。

它集上、下震击作用于一体，可接触钻进作业中遇阻、遇卡等钻井事故。

它在不需要震击时，是钻柱的一部分，需震击时，随时可作业，因而提高了工作效率。

产品代号的含义：B Z 165外径165震击器的“震”北方钻采工具研究所的“北”BZ159/165--------BZ159和BZ165两套产品的外筒外径不同，其余尺寸完全相同。

2．结构与工作原理。

2.1 结构外形及主要尺寸如图一。

内部结构如本说明书后附产品总图（图中未画出曲屈接头）。

本震击器是同类产品中结构最新式、最简化、操作最方便的。

2.2 上击工作原理图一所示为装配调试合格的位置，即准备出发（解锁）状态。

图二为局部放大图。

上图为准备击发位置。

运行轴与运行套的内齿对应啮合，运行套外部齿与摩擦衬套内部齿是齿顶对齿顶的摩擦状态。

当钻柱上提，通过上接头1，上控制套3，中部套筒28，下控制套37，下调节套29，压缩弹簧管25，26，27使运行套21相对摩擦衬套下移。

当运行套的外齿齿顶与摩擦衬套的齿间相对应时，运行衬套在运行轴的作用下涨开，运行轴的齿从运行套内齿滑出，如图二中图。

此时钻柱储备的能量释放，向上震击。

下放钻柱，整个工具又恢复图二上部的状态，即准备击发状态。

重复上述操作，就可使钻具解卡。

2.3 下击工作原理在运行套的上部，还有一组三件与26，27，28完全相同的弹簧管。

当下压钻柱时，通过上接头1，上控制套3，上调节套18，压缩上面一组弹簧管。

运行套相对于摩擦衬套上行，钻柱储能。

当达到预定的吨位，运行套的齿顶与摩擦衬套的顶间相对应，运行衬套涨开，运行轴齿从运行套内的齿中滑出，产生下击，与上击方向相反如图二下图所示。

第一章DB2 UDB 概况1.1、DB2 UDB的产品家族UDB(Universal Database )的前身为DB2，是IBM公司开发的关系型数据库管理系统。

从其诞生之日开始，DB2就定位于要为各种规模的企业提供稳定、高效的数据管理支持。

可以说，DB2是当前适用范围最广泛的数据库产品。

我们对DB2产品的划分通常分为两种方法：一种方法是按其所能支持的硬件和操作系统平台进行划分，另一种方法是按其所能支持的用户规模的不同进行划分。

DB2产品几乎覆盖了当前所有流行的硬件和操作系统平台。

在大型机操作系统上，有DB2 for OS/390、DB2 for MVS/ESA、DB2 for VSE 和DB2 for VM等多种产品；在由IBM公司设计的小型机AS/400上，DB2已经嵌入在操作系统OS/400之中，成为其不可分割的一部分。

DB2对UNIX操作系统的支持同样十分广泛，可以在AIX、HP-UX、Solaris、SCO-UNIX、SINIX 等多种系统上找到其相应的版本。

另外，在PC操作系统上，DB2可以对Window 9x、Windows NT以及OS/2等多种操作系统提供支持。

UDB 6.1还增加了对Linux操作系统的支持。

以上我们所提到的只是DB2服务器所能运行的平台，DB2的客户端所能支持的平台更为广泛，除了以上提到的所有平台之外，DB2的客户端还能运行在Dos、Windows 3.x、Mac OS以及SGI公司的IRIS系统之上。

UDB产品除了能够对各种硬件和操作系统平台进行支持之外，为了适应不同用户群的需要，UDB提供了不同级别的产品，对小到个人用户，大到跨国企业的不同需求提供支持。

以下是对UDB 6.1版本不同级别产品的特点介绍：UDB卫星版：是专门为移动用户设计的小型数据库产品。

适合于偶尔连接DB2控制服务器来与公司系统交换数据的单用户系统。

它既能允许用户对本地数据进行各种修改，又可以接受远程卫星控制器的集中管理，减轻本地用户的管理负担。

BZB-110GW13D变压器中性点接地保护装置
一、产品用途
中性点的运行方式不同，其技术特性和工作条件也不同，因而对运行的可靠性、设备绝缘及其保护措施的影响和要求也不一样BZB型变压器中性点接地保护成套装置专用
于110KV、220KV电力变压器中性点，以实现变压器中性点接地运行或不接地运行两种不同的运行方式。

二、使用条件
1、适用于户内、外。

2、环境温度：不低于－40℃，不高于＋55℃；相对湿度：不大于95％（25℃）。

3、海拔高度不超过4000m，超出4000m可根据实际情况特制。

4、地震烈度7度及以下地区；最大风速不超过35m／S。

5、电网频率：58～62Hz（60Hz系统）、48～52Hz（50Hz系统）。

6、安装场所的空气中不应含化学腐蚀气体和蒸气，无爆炸性尘埃。

三、使用须知
1、变压器中性点电流互感器一般装设在变压器出线套管上，不包括在本装置内。

2、订货时应告知变压器额定电压，电流互感器变比，隔离开关额定电流、操作机构形
式，氧化锌避雷器额定电压等参数。

当未具体指定时，将按本说明书技术数据标准配置交货。

3、电流互感器二次侧设0.5／10P两个次级。

供测量保护使用。

不用时应将其短路。

4、连接到变压器中性点的导线截面和型式由用户决定。

制造：上海昌开电器有限公司。

GPSBD®使用手册一、前言1、系统介绍1.1系统简介GPSBD®--GPSBigData(gps大数据)欢迎使用目前国内技术领先的卫星定位监控系统-GPSBD®卫星定位监控基础系统，他将轻松的帮您完成LBS 位置服务相关的系统软件开发。

您在开发过程中，不必关心复杂的底层数据处理，只需要关心自己的业务即可。

系统采用目前主流的技术架构，以及数据处理和缓存技术。

保障了系统的高并发，高可靠，稳定，可扩展性强，易维护升级。

1.2主要功能介绍●支持多达几十种不同厂家的不同型号设备完美接入。

●支持各种主流的地图互相切换展示（PS：高德，谷歌，百度，必应地图，天地图，OSM，YandexMap ...）●插座实时展示设备的位置，碾压传统系统的接口轮询来获取数据（PS：如果设备上报频率可以1秒一次，地图上将平滑实时展示设备当前的位置没有任何延迟，传统的轮询至少延迟15秒）。

●插座实时推送设备的报警事件，并在地图上动态展示出报警的位置。

●插座实时推送设备的当前的属性状态，如电量，卫星颗粒个数，电压，ACC，GSM信号强度，防盗状态以及油耗情况等等......有必要强调一下实时，一切都是实时的没有任何延迟。

所有数据的展示和物理状态之间延迟取决于硬件的上报频率和SIM卡传输速度。

●可创建多种形式的围栏，满足不同的场景需求，如常用的圆形围栏，多边形围栏，以及行政区域围栏。

●可创建父子树形结构关系的分组来管理设备，分组关联绑定围栏，等同于分组下所有分组及其所有设备绑定围栏。

避免传统系统中每个设备都要单独绑定的繁琐操作。

●系统可根据不同的设备类型展示不同的下发命令视图，通过调整参数即可直接下发给指定设备，并展示设备返回的响应内容。

并且可直接下发自定义的透传指令。

●历史轨迹播放并导出轨迹明细●设备常用的报表数据统计，并生成可视化图表，直观表现数据走势。

●地图测量距离和面积●地图导出●用户角色和权限可自由配置，管理员可创建多个角色，每个角色权限颗粒度可细分到目录，菜单，按钮，数据，单个用户可分配多个角色。

B-500-EXT-230-RSpg.2B-500-EXT-230-RS Installation and Users ManualIMPORTANT SAFETY INSTRUCTIONSWARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.1. Read and follow all instructions and warnings in this manual. Keep for future reference.2. Do not use this apparatus near water.3. Clean only with a dry cloth.4. Do not block any ventilation openings. Install according to manufacturer’s instructions.5. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat.6. Do not override the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades - one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.7. Protect the power cord from being walked on or pinched particularly at plug, convenience receptacles, and the point where it exits from the apparatus.8. Only use attachments/accessories specified by the manufacturer.9. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as when the power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.10. DO NOT EXPOSE THIS EQUIPMENT TO DRIPPING OR SPLASHING AND ENSURE THAT NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, ARE PLACED ON THE EQUIPMENT.11. TO COMPLETELY DISCONNECT THIS EQUIPMENT FROM THE AC MAINS, DISCONNECT THE POWER SUPPLY CORD PLUG FROM THE AC RECEPTACLE.12. THE MAINS PLUG OF THE POWER SUPPLY CORD SHALL REMAIN READILY OPERABLE.CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE COVER. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICEPERSONNEL.The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of un-insulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.B-500-EXT-230-RS Installation and Users ManualTABLE OF CONTENTS1. Overview (4)2. Package Contents (4)3. Features (5)4. Connections and Controls (6)4.1. B-500-EXT-230-RS Transmitter (6)4.2. B-500-EXT-230-RS Receiver (7)5. Basic Connections (8)5.1. HDBaseT Link (RJ45) Connection (8)5.2. IR Control Connections (9)5.2.1. IR Control In (3.5mm {1/8”} Mono) - Transmitter (10)5.2.2. IR Receiver In (3.5mm {1/8”} Stereo) - Receiver (10)5.2.3. IR Flasher Out (3.5mm {1/8”} Mono) – Transmitter and Receiver (11)5.3. RS232 Control Connections (11)5.3.1. RS232 Control (DB9) Connection (11)5.4. HDMI Out to Display (HDMI) (12)5.5. Latch Locking Power Supply (12)6. Installation (13)6.1. B-500-EXT-230-RS Transmitter Installation (13)6.2. B-500-EXT-230-RS Receiver Installation (13)7. Specifications (14)8. WARRANTY (15)9. Contacting Technical Support (15)pg.3B-500-EXT-230-RS Installation and Users Manual1. OVERVIEWThe B-500-EXT-230-RS extends HDMI over single Cat5e/6 using HDBaseT technology allowing video and audio transmission to remote displays. In addition, the B-500-EXT-230-RS is equipped with bi-directional IR pass-through and bi-directional RS-232 pass-through all over a single Cat5e/6 cable.Supports all HDMI defined Audio and Video formats, including 3D Video.The Power Over Cable feature requires only one end of the link to be powered.2. PACKAGE CONTENTS(1) B-500-EXT-230-RS Transmitter(1) B-500-EXT-230-RS Receiver(1) 24V DC 1A Power Supply(4) Mounting Screws(8) Rubber Feet(1) User Manual(1) IR Adapter Cablepg.4B-500-EXT-230-RS Installation and Users Manual 3. FEATURESForm and Function• Wall-Mountable Housing Design for Easy Installation• Extends all HDMI formats up to 4Kx2K via a Single cableCat5e Up to 200ftCat6/Cat6a Up to 230ft• Transmits HDMI Signal via HDBaseT up to 10.2Gbps• HDCP 1.2 Compliant• Power Over Cable (POC) Allows for Single Power Supply• Latch Locking Power SupplyVideo• 2D Resolutions up to 1080p@60Hz – 48 Bit; including Deep Color• 4Kx2K• 3D Resolutions up to 1080p@24Hz – 48 Bit; including Deep Color• EDIDs Read from Connected Display to SourceAudio•Supports all HDMI supported Audio Formats, including DTS-HD Master and Dolby TrueHD Control Functionality• Bi-Directional IR Pass-Through- Supports IR Signal from 20kHz To 60kHz- Adaptive IR Input Levels (3.5V DC To 12V DC)• Bi-Directional RS232 Up to 115.2 Kb/spg.5B-500-EXT-230-RS Installation and Users Manual4. CONNECTIONS AND CONTROLS4.1. B-500-EXT-230-RS Transmitter1. Latch-Locking Power JackConnect to the included 24V DC 1A Power Supply.2. Power LEDIndicates current state of Power; illuminates RED when power is applied.3. HDMI In (HDMI)Connect an HDMI cable to the HDMI output of a source, AV Receiver, HDMI Splitter, or HDMISwitcher/Matrix.4. IR Flasher Out (3.5mm {1/8”} Mono)Connect an IR flasher to use IR signals sent from the remote location.5. IR Control In (3.5mm {1/8”} Mono)C onnect the IR output of an Automation System or IR connecting block to send IR signals to the remotelocation. To simplify connection to most Automation Systems, this port does not supply power.6. RS232 Operation Mode Dip SwitchesSwitch 1: Configures RS232 DB9 connection pins for DCE or DTE communication.Switch 2: Configures RS232 DB9 connection: ON for Pass-Through (normal operation) or SERVICE for Firmware update.See section 5.3.1.1 RS232 Operation Mode.7. RS232 Control (DB9)Connect to an Automation System RS232 control port to send RS232 signal to the Receiver.8. HDBaseT Link to Receiver (RJ45)Connect to HDBaseT RJ45 on Receiver; this connection follows standard TIA/EIA-568B.9. Signal Link LEDIndicates link status with Receiver; illuminates GREEN when sync is present. Blinks when in Low Power Mode.pg.6B-500-EXT-230-RS Installation and Users Manual4.2. B-500-EXT-230-RS Receiver1. Latch-Locking Power JackConnect to the included 24V DC 1A Power Supply.2. Power LEDIndicates current state of Power; illuminates RED when power is applied.3. HDMI Out to Display(HDMI)Connect an HDMI cable to the HDMI In of the display or AV Receiver.4. IR Flasher Out (3.5mm {1/8”} Mono)Connect an IR Flasher to transmit IR signals sent from the remote location.5. IR Receiver In (3.5mm {1/8”} Stereo)C onnect an IR Receiver to send IR signals to the Transmitter from the remote location. Includes+9V to power IR Receiver.6. RS232 Operation Mode Dip SwitchesSwitch 1: Configures RS232 DB9 connection pins for DCE or DTE communication.Switch 2: Configures RS232 DB9 connection: ON for Pass-Through (normal operation) or SERVICE for Firmware update.See section 5.3.1.1 RS232 Operation Mode.7. RS232 Control (DB9)Connect to an Automation System RS232 control port to send RS232 signal to the Transmitter.8. HDBaseT Link to Transmitter (RJ45)Connect to HDBaseT RJ45 on Transmitter; this connection follows standard TIA/EIA-568B.9. Signal Link LEDIndicates link status with Transmitter; illuminates GREEN when sync is present. Blinks when inLow Power Mode.pg.7B-500-EXT-230-RS Installation and Users Manual5. BASIC CONNECTIONSNote:When a power supply is connected to either the Transmitter or Receiver,theHDBaseT link sends power to the other unit.Only1unit requires a power supply beconnected.5.1. HDBaseT Link (RJ45) ConnectionConnection Precautions!The B-500-EXT-230-RS is specified to operate with Cat5e/Cat6/Cat6a cables for communication between the Transmitter and Receiver. The transmission path may include Keystones and Patch Cables as long as the total length does not exceed 200ft for Cat5e and 230ft for Cat6/Cat6a.Note: The HDBaseT Link RJ45 connection includes a 24V signal. DO NOT connect anything into this port other than an HDBaseT Transmitter or Receiver.TIA/EIA Standard 568-B (Gold Pins Facing Up)Pin 1White/Orange Pin 5White/BluePin 2Orange Pin 6GreenPin 3White/Green Pin 7White/BrownPin 4Blue Pin 8Brownpg.8B-500-EXT-230-RS Installation and Users Manualpg.95.2. IR Control ConnectionsBi-directional IR signals are transmitted between the B-500-EXT-230-RS Transmitter and Receiver over the Cat5e/6 cable. How the IR connections function varies on the Transmitter and Receiver based on the common use cases for sending and receiving IR. This section outlines the operation of IR on the Transmitter and Receiver.Connection Precautions!• Before connecting an IR Receiver or an IR Automation System, verify that the B-500-EXT-230-RS is OFF to avoid damaging the unit.• The IR Receiver In (3.5mm {1/8”} Stereo) on the Receiver provides 9V power to power IR Receivers. This voltage can damage flashers and Automation Systems. Take caution before plugging an IR Flasher or IR Receiver into the respective IR sockets. The Manufacturer’s Warranty will not cover any damage that may occur. See IR Control Connections section for proper cabling.• Pin out configurations for IR Receivers and Automation Systems vary. Beforeconnecting to this input, review this section carefully in order to match the pin outs for the B-500-EXT-230-RS.”} Mono) -See Section 5.2.1”} Stereo)-See Section 5.2.2”} Mono)-See Section 5.2.3Cat5e/Cat6/Cat6a (RJ45)-See Section 5.1pg.10B-500-EXT-230-RS Installation and Users Manual5.2.1. IR Control In (3.5mm {1/8”} Mono) – Transmitter OnlyThe most common use of the IR Control In port is to send a wired IR signal from an Automation System to an IR Flasher connected to the Receiver. This connection does not include power for an IR Receiver. A 3.5mm {1/8”} Mono Cable is used to connect directly to the Automation System IR output or Connecting Block.5.2.2. IR Receiver In (3.5mm {1/8”} Stereo) – Receiver OnlyThe most common use of the IR Receiver port is to send an IR signal from a powered IR Receiver to an IR Flasher connected to the Transmitter. This connection includes +9V DC power for an IR Receiver. A 3.5mm {1/8”} Stereo Cable is used to connect directly to an IR Receiver, DO NOT connect a mono cable to this connection as damage may occur.If the system requires a powered IR Receiver at the Transmitter, a powered IR Block will be needed between the IR Receiver and the Transmitters IR Control In.If the system requires connection to an Automation System or Connecting Block to send IR to the Transmitter, the included IR Adapter Cable between the Automation System or Connecting Block output and the IR Receiver input must be used.IR Signal (Tip)GND (Sleeve)IR Signal (Tip)GND (Ring)9V DC (Sleeve)B-500-EXT-230-RS Installation and Users Manualpg.115.2.3. IR Flasher Out (3.5mm {1/8”} Mono) – Transmitter and Receiver5.3. RS232 Control ConnectionsBi-directional RS232 signals are transmitted between the B-500-EXT-230-RS Transmitter and Receiver over the Cat5e/6 cable. The Transmitter may be connected to an Automation System controller and the Receiver connected to an RS232 controllable device.5.3.1. RS232 Control (DB9) ConnectionTo eliminate the need to make cross over or ‘null modem’ cables, the RS232 pin outs can be configured for DCE or DTE. Set Switch 1 to DCE (Up) if the connected device is DCE, and to DTE (Down) if the connected device is DTE.Typically the Automation System will be DTE and the controlled device will be DCE, however,devices may vary. Refer to the manual for the connected devices for proper pin-out configuration.IR Signal (Tip)GND (Sleeve)RS232 Control (DB9)-See Section 5.3.1HDBaseT Link Cat5e/Cat6/Cat6a (RJ45)-See Section 5.1RS232DB9Pin OutsDCE (Up)DTE (Down)pg.12B-500-EXT-230-RS Installation and Users Manual5.3.1.1 RS232 Operation ModeThe RS232 connection is used for performing Firmware updates in addition to sending RS232 signals. Switch 2 is used to set the RS232 Mode.Note: Switch 2 must set to ON (Up) during normal RS232 Pass-Through operation.5.3.1.2. Firmware Update OperationAs new source and display devices become available, it may be necessary to modify the firmware in the B-500-EXT-230-RS. To perform firmware updates, the dipswitches must be set to DTE (Down) and Service. Detailed instructions and updated firmware will be posted to as they are released.5.4. HDMI Out to Display (HDMI)Connection Precautions!• We recommend using a 1 meter or shorter HDMI cable to connect the B-500-EXT-230-RS to the display; this will ensure the highest quality image on the display.5.5. Latch Locking Power SupplyWith Power Over Cable (POC), power is not required at both ends of the installation. When apower supply is connected to either the Transmitter or Receiver, the HDBaseT link sends power to the other unit. Only 1 unit requires a power supply be connected.SERVICE DTE RS232 Pass-Through(Up)Service (Down)B-500-EXT-230-RS Installation and Users Manual 6. INSTALLATIONNote: DO NOT connect power to the B-500-EXT-230-RS until all other connections are made and the unit is installed.6.1. B-500-EXT-230-RS Transmitter Installation1. Run the Cat5e/Cat6/Cat6a cable from the location of the Transmitter to the remote location ofthe Receiver.2. Mount the B-500-EXT-230-RS Transmitter in the desired location.3. Connect the HDMI Out of a source component using an HDMI cable.4. Connect the RS232 DB9 from an Automation System if being used.5. Connect an IR Control System to the IR Control In and/or IR Flasher if being used.6. Connect the Cat5e/6 cable to the B-500-EXT-230-RS Transmitter.7. Connect the 24V DC 1A Power Supply to the Latch-Locking Power Jack, unless POC is beingused to send power from the Receiver. DO NOT plug the power supply into an AC outlet until Step 9 under Receiver Installation.6.2. B-500-EXT-230-RS Receiver Installation1. Run the Cat5e/Cat6/Cat6a cable from the location of the Transmitter to the remote location ofthe Receiver.2. Install the B-500-EXT-230-RS Transmitter following the steps outlined in section 6.1. B-500-EXT-230-RS Transmitter Installation.3. Mount the B-500-EXT-230-RS Receiver in the desired location.4. Connect the Cat5e/6 cable to the B-500-EXT-230-RS Receiver.5. Connect an IR Flasher and/or IR Receiver if being used.6. Connect an HDMI cable from the B-500-EXT-230-RS to the display.7. Connect the RS232 DB9 to an RS232 controllable source if being used.8. Connect the 24V DC 1A Power Supply to the Latch-Locking Power Jack, unless POC is beingused to send power from the Transmitter.9. Plug the power supply for either the Transmitter or the Receiver (depending on which unit issupplying power) into an AC outlet.pg.13B-500-EXT-230-RS Installation and Users ManualTechnical Transmitter ReceiverHDMI Compliance HDMI 3DHDCP Compliance YesVideo Bandwidth10.2GbpsHDMI over UTP Transmission Resolution Cat5e Cat6/Cat6a1080i / 720p24-bit color200ft230ftFull HD 1080P24-bit color200ft230ftFull HD 1080P36-bit deepcolor200ft230ftInput TMDS Signal 1.2 Volts (peak-to-peak)Input DDC Signal 5 Volts (peak-to-peak, TTL)ESD Protection(1) Human body model — ±15kV (air-gap discharge) &±8kV (contact discharge) (2) Core chipset — ±8kV IR Signal (Bi-directional)Carrier frequency: 20-60kHzConnectionsHDBaseT Link1x RJ451x RJ45HDMI 1x HDMI Type A(19-pin female)1x HDMI Type A (19-pin female)IR Receiver (In)---1x 3.5mm StereoIR Control In1x 3.5mmMono---IR Flasher (Out)1x 3.5mmMono1x 3.5mmMonoRS232 Pass-Through DB9DB9Power Latch-Locking Latch-LockingControlsDipswitch 1RS232 Pin Configuration (DCE or DTE)Dipswitch 2RS232 Operation Mode (Pass-Through or FirmwareUpdate)MechanicalHousing Metal enclosureDimensions 6.25”x3.1”x1.3”Weight 1.1 lbs.Power Supply24V DC 1APower Consumption12 watt (max)Operation Temperature32~104°FStorage Temperature-4~140°FRelative Humidity20~90% RH (no condensation)Certifications and Compliance Product: CE, FCC, RohsPower Supply: CE, FCC, Rohs, UL7. SPECIFICATIONSpg.14B-500-EXT-230-RS Installation and Users Manualpg.158. WARRANTY2-Year Limited WarrantyThis Binary™ Product has a Two-Year Limited Warranty. This warranty includes parts and labor repairs on all components found to be defective in material or workmanship under normal conditions of use. This warranty shall not apply to products which have been abused, modified or disassembled. Products to be repaired under this warranty must be returned to SnapAV or a designated service center with prior notification and an assigned return authorization number (RA).9. CONTACTING TECHNICAL SUPPORTPhone: (866) 838-5052Email: **********************© 2012 Binary™121130-1620。