紧固件标准中英文对照表

紧固件-中英文对照No. 英文单词简写中文1 screw scr 螺丝2 nut nut 螺母3 washer wash 垫圈4 head hd 头5 thread thre 螺纹6 coating coat 镀层7 rivet riv 铆钉8 standoff stdoff 内外六角钉9 driver driv 穴10 hexagon hexa 六角11 tooth tooth 齿12 lock lck 锁13 spring spr 弹簧14 wave wave 波浪型15 pitch pitch 牙距16 partial thread PT 半螺纹17 PT PT 一种螺纹形式18 Full Thread FT 全螺纹19 silver silv 银20 cone cone 锥形21 Eco-syn Eco 30度牙的一种螺纹22 Thread Forming TF 自攻螺纹23 Self Tapping self tapp 自切屑螺纹24 pin pin 销25 shaft Shaf 轴26 steel St 铁27 stainless steel SS 不锈钢28 Brass(Cu) Bras(Cu) 铜29 Aluminum AL 铝30 Rubber Rub 橡胶31 machine screw mech scr 机制螺丝32 SEM screw SEM Scr 组合螺丝33 Material material 材料34 Grade GD 等级35 Finish Finish 表面处理36 Point Point 点37 Clamp Clam 夹子38 internal Int 内39 external ext 外40 thickness / 厚度41 length / 长度42 hole / 孔43 Metric Metcric 公制44 DIN / 德标45 ANSI / 美标46 JIS / 日标螺丝相关参数英语对照A: Machine Screw: 机械螺丝B: Tapping Screw: 自攻螺丝(分使用于金属与使用于塑料二种)B-1: Sheet Metal Tapping Screw. (铁板牙自攻螺丝)B-2: Plastic Tapping Screw. ( 塑料用, 自攻螺丝)C: Wooden Screw : 木工螺丝D: Drywall Screw : 水泥墙螺丝常见螺丝材质:a.Low Carbon Steel :低碳钢b. SS-304 : Stainless Steel 304c. SS-302: Stainless Steel 302 :结构韧性较好d. Aluminum 5052 :铝合金5052d. Brass: 黄铜e. Bronze: 青铜f. UNS C11000 Copper: 锑铜Finish Code: 外观处理规格Head Code: 头部外型螺丝型号Drive Code: 头部剖沟,特征型号Length Code: 螺丝长度(mm)A-1: Thread Code: 螺丝型号A-2: Length Code: 螺丝长度:A-3: Drive Code/ 头部剖沟,特征.a. Slotted: 一字( Minus )b. Phillips: 十字( Plus )c. Phil-Slot: 一字/十字d. Hex Scoket: 内六角e. One Way: 单向(只可锁入,不可退出) A-4: Head Code/ 头部外型.a. Flat: 平头(锁入后,顶部与工作件齐平)b. Oval: 色拉头c. Round: 圆头d. Pan: 圆扁头e. Truss: 大圆扁头f. Hex : 六角头A-5: Finish Code/ 外观处理.a. Z: Zine-Plated: 镀锌b. Ni: Ni-Plated: 镀镍c. Tin-Plated: 镀锡d. Zine Plated / Green Iridite: 镀锌绿膜处理.e. Radiant Plated: 镀五彩f. Passivate: 抗氧化处理.g. Alodial Finish: 无外观处理螺纹大径：Major Diam螺纹中径：Pitch diam螺纹底径：Minor diam通止规：Go/No go gage机械性能：mechanical and physical propertiesunified thread 统一英制螺纹Lustrate hydrogen after galvanizing to avoid hydrogen embrittlement 镀后去氢，防止氢脆Case carburization 表面渗碳With across flats 对边With across corners 对角Radius of fillet:头下圆角Transition thread length 过度螺纹Wrenching height 扳拧高度Rockwell 铬氏硬度Vickers 维氏硬度Brinell 布氏硬度Metallography microscope 金相显微镜Salt spray device 盐雾试验箱Tensile testing machine 拉力试验机Cold forming 冷打Hot forging 红镦P C 8 = property class 8 机械性能8级原材料：Raw material球化退火：Annealing冷拔：Drawing冷镦：Forming机加工：Machining螺纹成型：Roll Threading热处理：heat-treatment表面处理：finish去氢：Lustrating hydrogen检验：Inspection包装：Packing入库：Stocking车床：lathe磨制：grinding红打：hot forging冲压：punchingDiameter 直径Length 长度各类紧固件标准件产品英语翻译对照插片壁虎Steel Ceiling Anchors内迫壁虎Drop in Anchors碳钢锤钉壁虎Steel Hit Anchors碳钢六角螺帽Steel Hex Coupling Nuts强力车修壁虎Wedge Anchors外迫壁虎Cut Anchors化学壁虎Chemical Anchors不锈钢重载胀栓Heavy Duty Expansion Anchors鱼眼壁虎企眼长螺帽Tie Wire Anchors锌合金打入式壁虎Hammer Drive Anchors弹簧螺帽Strut Nuts兰花夹系列Toggle Bolts (Spring Toggle & Gravity Toggle)门窗、地板专用壁虎Nylon Frame Anchors or Metalframe Anchors石膏板中空壁虎Hollow Wall Anchors套管式壁虎Sleeve Anchors打入式壁虎鱼形尼龙壁虎Nylon Frame Harmmer Fixing (Nylon Hammer Drive Anchors)强力式锤钉壁虎Hit Anchors电梯壁虎Bolt Anchors重载壁虎Heavy duty anchors两片夹Loxin Masonry Anchors定位螺栓Set Bolts长型兰花夹Short Strap Anchors工具棒Drop in Setting Tools象脚壁虎Elephant foot anchors水泥预埋件Concrete Insert翻边胀轴Drop in Anchor with Lip冲件Legs Drywall Anchors六角盖头螺帽Hex Cap Nuts六角锯齿螺帽Hex Serrated Nuts六角轮缘螺帽Hex Flange Nuts高脚螺帽Hex Coupling Nuts(High Nuts)圆螺帽Round Nuts四角螺帽Square Nuts管用螺帽Pipe Nuts轮壳螺帽Wheel Nuts蝶型螺帽Wing NutsU形螺帽U NutsT形螺帽T Nuts环首螺帽Eye Nuts齿形螺帽Kep Nuts齿花螺帽Clinch Nuts耐候钢六角重型螺帽Corten Steel Heavy Hex Nuts焊接螺帽Weld Nuts高张力螺帽Heigh Strength Nuts建业用螺帽Structural Nuts不锈钢螺帽Stainless Steel Nuts铜螺帽Brass Nuts铝螺帽Aluminum Nuts合金钢螺帽Alloy Steel Nuts重型车螺帽Heavy Duty Wheel Hub Nuts铁器焊接袋帽Acorn Cap Nuts金属预置扭矩式螺帽All-Metal Prevailing Torque Type Nuts壁虎螺帽Anchor Nuts大尺寸螺帽Big Size Nuts铁盖袋帽Closed End Acorn Nuts盘形华司螺帽Conical Washer Nuts铁盖+尼龙圈组合盖帽Din 986 Domed Cap Nuts突缘尼龙盖帽Flange Nylon Insert Lock Nuts平面华司螺帽Flat Waser Nuts六角割沟螺帽Hex Slotted Nut自锁螺帽Self-Locking Nuts制止螺帽Sliding NutsSln-自动防松螺帽Sln Self-Locking Nuts其它特殊螺帽Special Nuts弹簧螺帽Spring Nuts不锈钢突缘螺帽Stainless Steel Flange Nuts 不锈钢六角轮缘尼龙螺帽Stainless Steel Flange Nylon Insert Lock Nuts不锈钢六角重型螺帽Stainless Steel Heavy Hex Nuts不锈钢六角螺帽Stainless Steel Hex Nuts不锈钢尼龙嵌入螺帽Stainless Steel Nylon Insert Lock Nuts普通六角螺帽Hex Nuts六角重型螺帽Heavy Hex Nuts薄型螺帽Hex Jam Nuts尼龙嵌入防松螺帽Nylon Insert Lock Nuts机械螺丝用六角螺帽Hex Machine Screw Nut 六角螺丝(栓) Hex Head Cap Screws(Hex Bolts)六角机械螺丝Hex Head Machine Bolts六角木牙螺丝Hex Lag Bolts四角螺丝Square Head BoltsT头螺丝T Head Bolts马车螺丝Carriage Bolts环首螺丝Eye Bolts内六角孔螺丝Hex Socket Cap Screws固定螺丝Set Screws螺椿栓Stud Bolts螺旋椿Screw Studs轮壳螺栓Wheel Bolts翼形螺丝Wing Screws自攻螺丝Self Tapping Screws自削螺丝Thread Cutting Screws钻尾螺丝Self Drilling Screws机械螺丝Machine Screws木螺丝Wood Screws家具螺丝Furniture Screws塑板螺丝Chipboard Screws墙用螺丝Drywall Screws基础螺栓Foundation BoltsU型螺栓U Bolts勾头螺栓Hook Bolts套挂螺丝Toggle Bolts突缘螺丝Flange Bolts轨道螺栓(鱼尾螺丝) Track Bolts耐候钢螺丝Corten Steel Heavy Hex Bolts扭矩控制螺栓T.C.Bolts高张力螺栓High Strength Bolts剪力钉(焊接螺丝) Welding Studs螺丝附华司组合Screws And Washers Assembled(Sems)大尺寸螺栓Big Size Bolts不锈钢小螺丝Stainless Steel Sheet Metal Screws不锈钢大螺丝Stainless Steel Bolts铝螺丝Aluminum Screws合金钢螺丝Alloy Steel Screws电子螺丝Electronic Screws微小精密螺丝Micro Screws塑料螺丝Plastic Screws复合材料用螺丝Particle Board Screws钛合金螺丝Titanium Alloy Bolts钛、锆、钼、铌等螺丝、零件、材料Ti,Zr,Mo,Nb Pare Metal Bolts Parts拇指螺丝Thumb Screws双头牙螺丝Double End Screws Hanger Bolt 车辆(汽车)螺丝、螺帽Automotive Fasteners 航天用螺丝Aerospace Fasteners飞机特殊扣件Source Control Bolts拉栓Blind Bolts面板螺丝Panel Fasteners电梯螺丝Elevator Bolts四角头固定螺丝Square Set Screws大头马车螺丝Step Bolts单向螺丝One Way Lag Screws管夹螺丝Hose Clamp Screws不锈钢固定螺丝Stainless Steel Hex Socket Cap Screws不锈钢内六角螺丝Stainless Steel Hex Socket Cap Screws铰链螺丝Hinge Screws货柜螺丝Container Screws复合材料钻尾螺丝Bi-Metal Self Drilling Screws三角牙螺丝Trilobular Thread Screws高低牙螺丝High Low Screws夹板用螺丝Particle Board Screws马桶螺丝Toilet Closet Bolts特长螺丝Special Longer Screws建业螺丝Building Fasteners不锈钢六角螺丝Stainless Steel Hex Socket Cap Screws其它特殊螺丝Special Screws Or Bolts不锈钢特殊螺丝Special Stainless Steel Screws宽牙螺丝（粗牙螺丝）Coarse Thread Screws 链带螺丝Collated Screws水泥螺丝Concrete Screws板模螺丝Construction Bolts锌蝶螺丝Die Cast Wing Screws; Zinc Alloy 重型车螺丝Heavy Duty Wheel Hub Bolts内六角固定螺丝Hex Socket Set Screws复合材料用螺丝（夹板用）Particle Board Screws犁壁螺丝Plow Bolts不锈钢木螺丝Stainless Steel Wood Screws 套挂螺栓及螺丝Toggle Bolts钛合金膨胀螺丝Titanium Alloy Expansion Bolts六角盖头螺帽Hex Cap Nuts六角锯齿螺帽Hex Serrated Nuts六角轮缘螺帽Hex Flange Nuts高脚螺帽Hex Coupling Nuts(High Nuts)圆螺帽Round Nuts四角螺帽Square Nuts管用螺帽Pipe Nuts轮壳螺帽Wheel Nuts蝶型螺帽Wing NutsU形螺帽U NutsT形螺帽T Nuts环首螺帽Eye Nuts齿形螺帽Kep Nuts齿花螺帽Clinch Nuts耐候钢六角重型螺帽Corten Steel Heavy Hex Nuts焊接螺帽Weld Nuts高张力螺帽Heigh Strength Nuts建业用螺帽Structural Nuts不锈钢螺帽Stainless Steel Nuts铜螺帽Brass Nuts铝螺帽Aluminum Nuts合金钢螺帽Alloy Steel Nuts重型车螺帽Heavy Duty Wheel Hub Nuts铁器焊接袋帽Acorn Cap Nuts金属预置扭矩式螺帽All-Metal Prevailing Torque Type Nuts壁虎螺帽Anchor Nuts大尺寸螺帽Big Size Nuts铁盖袋帽Closed End Acorn Nuts盘形华司螺帽Conical Washer Nuts铁盖+尼龙圈组合盖帽Din 986 Domed CapNuts突缘尼龙盖帽Flange Nylon Insert Lock Nuts平面华司螺帽Flat Waser Nuts六角割沟螺帽Hex Slotted Nut自锁螺帽Self-Locking Nuts制止螺帽Sliding NutsSln-自动防松螺帽Sln Self-Locking Nuts其它特殊螺帽Special Nuts弹簧螺帽Spring Nuts不锈钢突缘螺帽Stainless Steel Flange Nuts 不锈钢六角轮缘尼龙螺帽Stainless Steel Flange Nylon Insert Lock Nuts不锈钢六角重型螺帽Stainless Steel Heavy Hex Nuts不锈钢六角螺帽Stainless Steel Hex Nuts不锈钢尼龙嵌入螺帽Stainless Steel Nylon Insert Lock Nuts锌压属螺帽Zinc Die Casting Nuts普通六角螺帽Hex Nuts六角重型螺帽Heavy Hex Nuts薄型螺帽Hex Jam Nuts尼龙嵌入防松螺帽Nylon Insert Lock Nuts机械螺丝用六角螺帽Hex Machine Screw Nut合金钢线材盘元Alloy Steel Wire Rod球状化线材Annealing Wire And Rod黑铁丝Black Wire黄铜棒线Brass Wire And Rod磨光棒钢Bright Steel Bar(Hex/Round/Square)铜合金线Copper Alloy Wire线切割线 E.D.M Cutting Wire快削钢线材盘元Free Cutting Steel Wire Rod 线材Iron Or Steel Wire线材盘元Iron Or Steel Wire Rod洋白铜线Nickel Silver Wire磷青铜线Phosphate Bronze Wire不锈钢条棒Stainless Steel Bar(Round/Hex/Square)不锈钢冷锻线材Stainless Steel Cold Heading Wire不锈钢线(抽线后) Stainless Steel Draw Wire 不锈钢线材Stainless Steel Wire不锈钢线材及盘元Stainless Steel Wire And Rod棒钢Steel Bar(Hex/Round/Square)转回90度碾线头机90讧evolving Wire Twisting Machine气动拉钉机Air Riveter各式螺丝类产品自动包装Automatic Packaging For All Kinds Of Packaging自动包装机Automatic Packing Machine螺丝制造搓牙机械Automatic Thread Rolling Machine螺丝割尾加工机械Automatic Thread Slotting Machine螺丝制造成型机械Automatic Trimming Machine拉钉打头机Blind Rivet Heading Machine螺丝、螺帽成型机Bolt Formers,Nuts Formers,Headers螺丝、螺帽热处理Bolt Nut And Screws Heat Treatment螺丝、螺帽热处理炉Bolt Nut And Screws Heat Treatment Furnaces球状化电器炖炉Carburizing Furnace Vacuum And Bell Type Furnace超防锈复合瓷膜Ceramic Coating连续式光辉渗碳淬火炉Continuous Bright Carburizing Quenching Furnace连续式光辉调质淬火炉Continuous Bright Hardening Quenching Furnace中、高热镀锌光辉连续炉Continuous Bright Heat Treat Furnace连续式光辉热处理炉Continuous Type Bright Heat Treatment Furnace螺丝割尾及特殊割遘加工Machine Screw Shank Slotting螺丝钻孔加工Screw Shank Drilling鸡眼上下模Eyelets Dies一般线材、盘元、退火炉General Wire,Wire Rod,Annealing Furnace倒立式滑落型伸线机Handstand Type Wire Drawing Machine十字冲模Header Punches In Various Drives 成型冲模Header Punches In Various Drives 螺丝打头机Heading Machine螺丝制造高速搓牙机械High Speed Automatic Thread Rolling Machine高中低周波感应加热炉High,Medium,Low Frequency Induction Heater空心打头机Hollow Heading Machine热浸镀锌螺丝、螺帽Hot Dip Galvanizing Bolts And Nuts机械镀锌Mechanical Galvanized迷你成型机Mini-Formers成品自动收线机Non-Stop Coiler精抽自动收线机Non-Stop Coiler(Skinpass) 螺帽模Nut Forming Dies螺帽成型模Nuts Formers特殊零件成型机Parts Forming Maching冲模Punch Dies冲子Punch Pins罗拉成型机Rollers Formers机(踏)车用螺丝成型机Screw For Motorcycle Or Bicycle Heading Machine止付螺丝成型机Set Screws Formers套高成型机Sockets Formers一般线材、盘元、螺丝合金炖炉SpheroidizingBright Annealing Furnace球状化热处理炉Spheroidizing Heat Treatment Furnace攻牙机Tapping Machine螺丝攻、车刀、模具Taps Dies And Tools搓牙机铁屑分离装置Thread Chip Separator 滚牙轮Thread Rolling Dies牙板Thread Rolling Dies Plates精密油压滚牙机Hydraulic Thread Rolling Machines模具Tools六角整头模Trimming Dies Hexagan碳化钨模具Tungsten Carbide Die镀钛处理(Tin)专业加工服务Tin Hard Coating For Cutting Tools And Punch By Pvd电镀化学原料Various Electroplating Chemicals环规校正Calibration For Ring Gage环规、牙规、三线规校正Calibration For Ring Gage, Athread Gage, 3 Wire Gage螺丝、螺帽品检量测仪器Fasteners Inspection And Measurement Instruments螺丝、螺帽成型攻牙专用油Forming And Tapping Oils For Bolts And Nuts Formers螺丝、螺帽五金等检验Insptection Services For Fasteners And Hardware德国schatz扭力机代理Representative Of Schatz Torque MachinIso品质保证系统Iso Quality Assurance System生产管理系统Production Control System物料管理系统Material Control System齿轮Gears不锈钢牙条棒Stainless Steel Hread Rod马达轴承轴心组件Bearing Shaft(Motor)轴承轴心Bearing Shaft开口铆钉Blind Rivets长形拉帽Blind Rivet Nuts拉帽Blind Nuts拉钉Blind Rivets实心梢Clevis Pins And Straight Pins弹片Clips卷钉Coil Nails冷锻零件Cold Forming Part开口销Cotter PinsE型环E-Rings膨胀螺栓Expansion Anchor Bolts鸡眼钉Eyelets RivetsR型销Snap Pins闸、锁Latches And Keeper Assembleds其它特殊铆钉Other Specil Rivets销Pins格式管夹、管束Pipe Hanger铆钉Rivets螺旋锔及螺旋圈Screw Hook And Screw Rings中空钉Semi-Tubular Rivet开叉钉Split Drive Anchors弹簧华司Spring Washers弹簧蝴蝶夹Spring Wings不锈钢华司Stainlesssteel Washers钢铁钉Steel And Iron Nails搓牙铁钉Thread Nails钛合金铆钉Titaium Alloy Rivets管形铆钉Tubular Rivets华司Washers真空热处理Vacuum Heat Treatment螺丝、螺帽、五金、Diy扣件Fasteners合金钢工具Alloy Steel Tools螺栓模Bolt Heading Dies手动拉钉钳Hand Riveter船舶链Anchor Chain脚踏车链锁Bicycle Chain Locks螺丝起子Bit罗拉Chain Roller特殊铆合扣件Collars(A Blindfastener For Huck Intl)装饰链Decorative Chains自攻螺纹衬套Ensat Threaded Inserts六角扳手Hexagon Keys超音螺纹压入式螺纹自动锁扣Threaded Inserts For Plastic Injection Mouldeings汽车特殊杆接件Special Auto-Mobile Fastener As Your Needs螺纹护套Recoil Inserts链条用滚子Roller For Roller Chain金属板镶嵌组件及自动夹扣组件Sheet MetalFasteners工具套筒组件Socket Wrench Sets不锈钢链Stainless Steel Chains轭子T-Yoke轮胎链Tire Chains狗链Dog Chains喇叭头轭铁U-Yoke,T-Yoke For Speaker不锈钢输送带轮用轨道Stainless Wheel's Rack For Transporter工业用链Industrial Steel Link Chains拖链安全链Tow Chains And Safety Chains 机车离合器零件Manufacture Of Motorcycle's Cvt Parts牙条棒Thread Rod机(踏)车用螺丝、轴心Screws And Shafts For Motorcycle Or Bicycle针车用螺丝、轴心Screws And Shafts For Sewing Maching止付螺丝Socket Set Screws不锈钢宽牙螺丝Stainless Steel Coarse Thread Screws不锈钢高低牙螺丝Stainless Steel High-LowThread Screws不锈钢机械螺丝Stainless Steel Machine Screws不锈钢钻尾螺丝Stainless Steel Self Drilling Screws不锈钢自攻螺丝Stainless Steel Self Tapping Screws不锈钢自削螺丝Stainless Steel Thread Cutting Screws不锈钢三角牙螺丝Stainless Steel Tri-Lobular Thread Screws。

德国标准和国际标准、中国标准中英文对照表序号德国标准中文品名英文品名国际标准中国标准Item DIN-Standard Description in Chinese Description in English ISO-Standard GB-Standard1 DIN1 圆锥销taper pins ISO2339 GB1172 DIN7 圆柱销parallel pins ISO2338 GB119-863 DIN84 开槽圆柱头螺钉slotted cheese head screws ISO1207 GB65-854 DIN85 开槽盘头螺钉slotted pan head screws ISO1580 GB67-855 DIN93 单耳止动垫圈tab washers GB8546 DIN94 开口销split cotter pins ISO1234 GB917 DIN95 开槽半沉头木螺钉slotted raised csk head wood screws GB1018 DIN96 开槽半圆头木螺钉slotted round head wood screws GB999 DIN97 开槽沉头木螺钉slotted countersunk head wood screws GB10010 DIN125-A 平垫plain washers ISO7089 GB97.1-8511 DIN125-B 平垫(带倒角) mediun washers ISO7090 GB97.2-8512 DIN126 平垫plain washers ISO709113 DIN127-A 重型弹垫spring lock washers,tang ends GB724414 DIN127-B 标准弹垫spring lock washers,square ends GB93-8715 DIN128-A 鞍形弹垫single coil spring lock washers GB7245-8716 DIN137-A 弹簧止动垫圈curved spring washers17 DIN137-B 波形弹垫wave spring washers GB95518 DIN186 T型方颈螺栓T-head bolts with square neck GB37-8819 DIN188 T型双接头螺栓T-head bolts with double nip20 DIN258 螺纹圆锥销taper pins with threaded end ISO873721 DIN261 T型头螺栓T-head bolts22 DIN315AF 蝶型螺母(美制) wing nuts amercia form23 DIN315DF 蝶型螺母(德制) wing nuts germany form GB62-8824 DIN316AF 蝶型螺钉(美制) wing screws amercia form25 DIN317DF 蝶型螺钉(德制) wing screws germany form26 DIN319 圆球型盖型螺母ball knobs27 DIN404 开槽带孔球面圆柱头螺钉slotted capstan screws GB832-8828 DIN417 开槽长圆柱端紧定螺钉slotted set srews with full dog point ISO7435 GB75-8529 DIN427 开槽平端紧定螺钉(半牙) slotted set srews with chamfered end ISO2342 GB73-8530 DIN431 小六角特薄细牙螺母pipe nuts with thread GB808-8831 DIN432 外舌止动垫圈external tap GB856-8832 DIN433 小垫圈(用于圆柱头螺钉) washers for cheese head screws ISO7092 GB848-9533 DIN434 方斜垫圈(U型) square taper washers for U-section GB852-8834 DIN435 方斜垫圈(I型) square taper washers for I-sections GB852-8835 DIN436 方垫圈square washers36 DIN438 开槽凹端紧定螺钉slotted set with cup point ISO7436 GB74-8537 DIN439 六角薄螺母hexagon thin nuts ISO4035 GB6172-8638 DIN439 细牙六角薄螺母hexagon thin nuts ISO8675 GB6173-8639 DIN440 木螺钉专用垫圈rounds washers for wood constructions ISO709440 DIN443 密封帽sealing caps,push-in type41 DIN444 活节螺栓B 型eye bolts form B GB798-8842 DIN462 内舌止动垫圈internal tab washers43 DIN463 双耳止动垫圈washers with two taps GB855-8844 DIN464 滚花高头螺钉knurled thumb screws with collar GB834-8845 DIN465 开槽滚花高头螺钉slotted knurled thumb screws with collar46 DIN466 滚花高螺母knurled thumb nuts with collar GB806-8847 DIN467 滚花薄螺母knurled thumb thin nuts GB807-8848 DIN470 锁紧垫圈sealing washers49 DIN471 轴用弹性挡圈retaining rings for shafts(external),circlips GB894.1-8650 DIN472 孔用弹性挡圈retaining rings for bores(internal),circlips GB893.1-8651 DIN478 方头带垫螺栓square head bolts with collar52 DIN479 方头圆柱底端螺栓square head bolts with half dog point53 DIN480 方头带垫半圆底端螺栓square head bolts with collar,half dog point and rounded end54 DIN508 T型槽螺母T-slot nuts ISO29955 DIN525 单头螺柱single end studs56 DIN529 地脚螺栓masonry bolts GB799-8857 DIN546 带槽圆螺母slotted round nuts GB817-7658 DIN547 端面带孔圆螺母round nuts with drilled holes in one face GB815-8859 DIN551 开槽平端紧定螺钉slotted sit screws with flat point ISO4776 GB73-8560 DIN553 开槽锥端紧定螺钉slotted set screws with cone point ISO7434 GB71-8561 DIN555 六角螺母hexagon nuts ISO403462 DIN557 方螺母-C square nuts GB39-8863 DIN558 六角头螺钉hexagon screws ISO401864 DIN561 六角头圆柱端紧定螺钉hexagon set screws with full dog point65 DIN562 薄型方螺母-B square nuts without bevel(pressed nuts)66 DIN571 六角头木螺钉hexagon head wood screws (coach screws) GB102-8667 DIN580 吊环螺钉lifting eye bolts ISO3266 GB825-7668 DIN582 吊环螺母lifting eye nuts69 DIN601 六角头螺栓hexagon bolts ISO401670 DIN603 大半圆头方颈螺栓(马车螺栓) mushroom head square neck bolts (carriage bolts) ISO8677 GB14-8871 DIN604 沉头带插销马车螺栓flat countersunk nib bolts72 DIN605 沉头长方颈马车螺栓flat countersunk long square neck bolts73 DIN607 半圆头带插销马车螺栓cup head nib bolts74 DIN608 沉头短方颈马车螺栓flat countersunk short square neck bolts75 DIN609 六角头精配螺栓（长螺纹）hexagon fitted bolts,long thread76 DIN610 六角头精配螺栓（短螺纹）hexagon fitted bolts,short thread77 DIN653 滚花平头螺钉knurled thumb screws thin type GB835-8878 DIN660 半圆头铆钉round head rivets ISO1051 GB867-8679 DIN661 沉头铆钉contersunk head rivets ISO1051 GB869-8680 DIN662 半沉头铆钉raised contersunk head rivets ISO105181 DIN674 大扁头铆钉mushroom head rivets ISO105182 DIN703 重型侧面带孔圆螺母adjusting rings,heavy range (shafting collars)83 DIN705 侧面带孔圆螺母adjusting rings,light range (shafting collars) GB816-8884 DIN741 卡头wire rope clips85 DIN787 T型槽螺钉T-slot screws ISO29986 DIN835 双头螺柱（牙长=2D）studs-metal (end=2d) GB900-8887 DIN906 内六角锥型闭锁螺钉hexagon socket pipe plugs,conical thread88 DIN908 内六角直型闭锁螺钉hexagon socket screw plugs,cyl. thread89 DIN909 外六角锥型闭锁螺钉hexagon head pipe plugs,conical thread90 DIN910 外六角直型闭锁螺钉hexagon head screw plugs,cyl.thread91 DIN911 内六角扳手socket wrenches ISO293692 DIN912 内六角圆柱头螺钉hexagon socket cap screws ISO4762 GB70-8593 DIN913 内六角平端紧定螺钉hexagon socket set screws with flat point ISO4026 GB77-8594 DIN914 内六角尖端紧定螺钉hexagon socket set screws with cone point ISO4027 GB78-8595 DIN915 内六角圆柱端紧定螺钉hexagon socket set screws with dog point ISO4028 GB79-8596 DIN916 内六角凹端紧定螺钉hexagon socket set screws with cup point ISO4029 GB80-8597 DIN917 薄型盲螺母hexagon cap nuts98 DIN920 开槽小圆柱头螺钉slotted short cheese head screws99 DIN921 开槽大圆柱头螺钉slotted large cheese head screws GB838-88100 DIN923 开槽圆柱头轴肩螺钉slotted pan head screws with shoulder GB830-88101 DIN927 开槽无头轴肩螺钉slotted shoulder screws102 DIN928 焊接方螺母square weld nuts GB/T13680-92103 DIN929 焊接六角螺母hexagon weld nuts GB/T13681-92104 DIN931 六角头螺栓（半牙）hexagon head screws ISO4014 GB5782-86105 DIN933 六角头螺栓（全牙）hexagon head screws ISO4017 GB5783-86106 DIN934 六角头螺母(1型) hexagon full nuts ISO4032 GB6170-86107 DIN934 细牙六角头螺母(1型) hexagon full nuts ISO8673 GB6171-86108 DIN935 开槽六角螺母hexagon slotted and castle nuts ISO7035 GB6178-86109 DIN936 六角头薄螺母hexagon thin nuts ISO4035 GB6172.1-86110 DIN937 六角头开槽薄螺母hexagon thin slotted and castle nuts ISO7038 GB6181-86111 DIN938 双头螺距（牙长=1D）studs metal (end=1d) GB897-88112 DIN939 双头螺距（牙长=1.25D）studs metal (end=1.25d) GB898-88113 DIN940 双头螺距（牙长=1.5D）studs metal (end=1.5d)114 DIN960 六角头细牙螺栓（半牙）hexagon head bolts,metric fine pitch thread ISO8765 GB5785-86115 DIN961 六角头细牙螺栓（全牙）hexagon head bolts,metric fine pitch thread ISO8676 GB5786-86116 DIN962 头部穿孔六角头螺栓additional shapes and versions for bolts117 DIN963 开槽沉头螺钉slotted countersund head screws ISO 2009 GB68-85118 DIN964 开槽半沉头螺钉slotted raised countersunk oval head screws ISO 2010 GB69-85 119 DIN965 十字槽沉头螺钉cross recessed countersunk head screws ISO7046 GB819-85120 DIN966 十字槽半沉头螺钉cross recessed raised countersunk head screws ISO7047 GB820-85121 DIN970 六角头螺母hexagon nuts type-1122 DIN971 六角头螺母hexagon nuts type-2123 DIN972 细牙六角头螺母(2型) hexagon nuts with fine thread ISO8674 GB6176-86124 DIN975 牙条(全螺纹) threaded rods(studdings) GB15389-94125 DIN976 螺纹销threaded pins(stud bolts)126 DIN979 六角头开槽薄螺母（2型）hexagon thin slotted and castle nuts127 DIN980 全金属六角锁紧螺母（1型）prevailling torque type hexagon nuts,all metall nuts ISO7199 GB6184-86128 DIN981 圆螺母locknuts ISO2982 GB812-88129 DIN982 六角头尼龙锁紧螺母prevailling torque type hexagon nuts,heavy type ,with nylon insert ISO7040 GB889.1-86130 DIN985 六角头薄型尼龙锁紧螺母prevailling torque type hexagon nuts,heavy type ,with nylon insert ISO10511 GB6172.2-86131 DIN986 六角盖型尼龙锁紧螺母prevailling torque typedomed capnuts with nylon insert132 DIN988 配合垫片shim rings133 DIN1052 木材连接用垫片washers for timber connectors134 DIN1151 沉头钢钉round plain head nails135 DIN1440 销钉专用垫片A型plain washers for clevis pins(A型) ISO8738136 DIN1441 销钉专用垫片plain washers for clevis pins137 DIN1444 带头销钉clevis pins with head ISO2341138 DIN1471 圆锥型槽销grooved pins,taper grooved ISO8744 GB/T13829.2139 DIN1472 圆锥型槽销(半槽) grooved pins,taper grooved half length ISO8745 GB/T13829.2 140 DIN1473 平行槽销(带倒角) grooved pins,parallel grooved full length ISO8740141 DIN1474 前端凹槽槽销grooved pins,reserve grooved half length ISO8741142 DIN1475 中部凹槽槽销grooved pins,centre grooved ISO8742143 DIN1476 圆头槽销grooved pins with round head ISO8746 GB/T13829.3144 DIN1477 沉头槽销grooved pins with countersunk head ISO8747145 DIN1479 六角螺母棒turnuckles(centre parts),made out of hexagon bar146 DIN1480 花篮螺栓turnuckles with eye bolt and hook bolt147 DIN1481 弹性圆柱销spring pins,heavy type ISO8752 GB879-86148 DIN1587 组合式盖型螺母hexagon domed cap nuts GB802-88149 DIN1804 开槽圆螺母（配合沟头扳手）slotted round nuts for hook spanner150 DIN1816 圆螺母（带插销孔）round nuts with set holes151 DIN2093 盘型弹簧垫圈disc springs152 DIN3017 喉箍hose clamps153 DIN3404 润滑油嘴（旋扭头）lubricating nipples,button head154 DIN3567 管夹shackles for conduilts155 DIN3570 U型螺栓stirrup bolts(U-bolts)156 DIN6319 球面垫圈spherical washers,conical seats GB849-88157 DIN6325 圆柱销parallel pins ISO8734158 DIN6330 厚六角螺母hexagon nuts ,1.5d GB56-88159 DIN6331 厚六角法兰面螺母hexagon nuts ,1.5d with collar GB6177-86160 DIN6334 长六角螺母hexagon nuts ,3d161 DIN6797-A 外齿锁紧垫圈external teeth lock washers GB862.1-87162 DIN6797-I 内齿锁紧垫圈internal teeth lock washers GB861.1-87163 DIN6798-A 外锯齿锁紧垫圈external teeth serrated lock washers GB862.2-87164 DIN6798-I 内锯齿锁紧垫圈internal teeth serrated lock washers GB861.2-87165 DIN6799 开口挡圈retaining rings for shafts(E-rings),circlips GB896-76166 DIN6885 平键（A型）parallel keys(form A ) ISO773/2491167 DIN6888 半圆键woodruff keys ISO3912168 DIN6899 嵌环（支撑环）thimbles169 DIN6900 机器螺钉和垫圈组合件screws and washers assemblies GB9074.1-.17170 DIN6901 自攻螺钉和垫圈组合件tapping screws and washers assemblies GB9074.18-.23 171 DIN6912 薄型带孔内六角圆柱头螺钉hexagon socket head cap screws with hole,low head 172 DIN6914 大六角头螺栓hexagon head bolts with large head(friction grip bolts)173 DIN6915 大六角螺母hexagon nuts with large wideth across flat(friction grip nuts)174 DIN6916 大垫圈round washers for friction grip bolts175 DIN6917 楔型方垫圈spuare taper washers for friction grip bolts on T-sections176 DIN6923 六角法兰面螺母hexagon flange nuts ISO4161 GB6177-86177 DIN6925 全金属六角锁紧螺母(2型）prevailing torque type hexagon nuts,all metallic nuts ISO7042 GB6185.1-2000178 DIN7337 开口型抽芯铆钉（沉头、扁圆头）blind rivets GB12617/12618179 DIN7338 扁平头半空心/全空心铆钉rivets for brake and clutch lining GB875/975-86180 DIN7343 螺旋夹紧销spiral pins ISO8750181 DIN7346 轻型弹性圆柱销spring pins,light type ISO13337182 DIN7349 重型弹性圆柱销用垫圈washers for bolts with heavy type spring pinss183 DIN7500 ISO公制螺纹螺钉(多种头型) threadforming screws for ISO-metric thread184 DIN7504 自攻自钻螺钉(多种头型) self-drilling tapping screws185 DIN7513 开槽切削螺纹螺钉(多种头型) thread cutting screws186 DIN7516 十字槽切削螺纹螺钉(多种头型) thread cutting screws cross recess187 DIN7965 T型四爪螺母tee nuts with pronge188 DIN7968 钢结构用六角头螺栓连接副hexagon head fitted bolts for steel structures GB1228/1229/1230189 DIN7971 开槽盘头自攻螺钉pan head tapping screws with slot ISO1481 GB5282-85190 DIN7972 开槽沉头自攻螺钉countersunk flat head tapping screws with slot ISO1482 GB5283-85191 DIN7973 开槽半沉头自攻螺钉raised countersunk oval head tapping screws with slot ISO1483 GB5284-85192 DIN7976 六角头自攻螺钉hexagon tapping screws ISO1479 GB5285-85193 DIN7980 圆柱头螺钉用弹簧垫圈spring lock washers for screws with cylindrical heads ISO8738194 DIN7981 十字槽盘头自攻螺钉pan head tapping screws with cross recessed ISO 7049 GB845-85195 DIN7982 十字槽沉头自攻螺钉countersunk flat head tapping screws with cross recessed ISO7050 GB846-85196 DIN7983 十字槽半沉头自攻螺钉raised countersunk oval head tapping screws with cross recessed ISO7051 GB847-86197 DIN7984 薄型内六角圆柱头螺钉hexagon socket head cap screws with，reduced head198 DIN7985 十字槽盘头螺钉pan head screws with cross recessed ISO7045 GB818-85199 DIN7989 钢结构用垫圈washers for steel structures GB1230-84200 DIN7990 钢结构用六角头螺栓hexagon head bolts for steel structures GB1229-84201 DIN7991 内六角沉头螺钉hexagon socket countersunk head screws ISO10642202 DIN7993 轴用钢丝挡圈roundwire snap rings for shafts GB895.2-86203 DIN7995 十字槽半沉头木螺钉cross recessed raised countersunk head wood screws GB952-86204 DIN7996 十字槽圆头木螺钉cross recessed round head wood screws GB950-86205 DIN7997 十字槽沉头木螺钉cross recessed countersunk head wood screws GB951-86206 DIN8140 螺纹护套（普通\自锁等）ciol inserts,coarse,fine thread,silf locking207 DIN9021 大外径垫圈washers,outside diameter appro.3d ISO7093 GB96-85208 DIN11024 弹簧卡子spring cotter for a bolt209 DIN13257 平板螺栓belting bolts (elevator bolts)210 DIN18182 干壁钉（墙板钉）dry wall screws211 DIN28129 环型螺母lifting nuts(eye nuts) GB63-88212 DIN70952 圆螺母用止退垫圈tab washers for slotted round nuts GB858-88。

螺丝通用表示方法
一般来说，电子小螺钉是变化最多的了，很多采购人员在下单时的表达不是很规范，这样造成不必要的错误。

下面是一些可供参考的表示方法：
例：
4 X 10 PW A .H .C (+)
① ② ③ ④ ⑤ ⑥ ⑦
① 螺钉直径
② 螺钉长度
③ 螺钉头型
V：蘑菇头 C：圆柱头 F(K)：沉头 H：六角头 HW：六角头带垫圈
O：半沉头 P：平元头 R：半元头 T：大扁头 PW：平元头带垫圈
B：球面圆柱头
④ 螺钉牙型
A：自攻尖尾(日标第1种)疏 AB：自攻尖尾(日标第4种)密
B：自攻平尾(日标第2种)疏 C：自攻平尾(日标第3种)密
P：双丝牙 HL：高低牙 U：菠萝牙纹
T：自攻平尾切脚 AT：自攻丝尖尾切脚 M：机械牙
BTT：B型三角牙 CCT：C型三角牙 PTT：P型三角牙
STT：S型三角牙
⑤ 热处理：
H(有热处理) N(没热处理)
⑥ 表面处理
Zn：白锌 C：彩锌 B：蓝锌
F：黑锌 O：氧化黑 Ni：镍
Cu：青铜 Br：红铜 P：磷化
⑦ 备注
(WIS)：单活动弹垫圈 (－)：一字槽 (Cu)：黄铜 (H)：内六角
(WIF)：单活动平垫圈 (±)：±槽 (Y)：Y型槽 (H)：H型槽
(WIT)：单活动外齿垫圈 (＋)：十字槽 (PZ)：米字槽 (L)：止退花齿
(W2SF)：双活动平弹垫圈 (SUS)：不锈钢 (Br)：红铜 (12.9)：12.9级螺钉
(W=6mm)：垫圈外径=6mm (8.8):8.8级螺钉 (T)：菊花槽 (10.9)：10.9级螺钉
(R)：其它注释。

紧固件DIN ISO GB标准中英文对照表序号德国标准中文品名英文品名国际标准中国标准Item DIN-Standard Description in Chinese Description in EnglishISO-Standard GB-Standard1 DIN1 圆锥销 taper pins ISO2339 GB1172 DIN7 圆柱销 parallel pins ISO2338 GB119-863 DIN84 开槽圆柱头螺钉 slotted cheese head screws ISO1207 GB65-854 DIN85 开槽盘头螺钉 slotted pan head screws ISO1580 GB67-855 DIN93 单耳止动垫圈 tab washers GB8546 DIN94 开口销 split cotter pins ISO1234 GB917 DIN95 开槽半沉头木螺钉 slotted raised csk head wood screws GB1018 DIN96 开槽半圆头木螺钉 slotted round head wood screws GB999 DIN97 开槽沉头木螺钉 slotted countersunk head wood screws GB10010 DIN125-A 平垫 plain washers ISO7089 GB97.1-8511 DIN125-B 平垫(带倒角) mediun washers ISO7090 GB97.2-8512 DIN126 平垫 plain washers ISO709113 DIN127-A 重型弹垫 spring lock washers,tang ends GB724414 DIN127-B 标准弹垫 spring lock washers,square ends GB93-8715 DIN128-A 鞍形弹垫 single coil spring lock washers GB7245-8716 DIN137-A 弹簧止动垫圈 curved spring washers17 DIN137-B 波形弹垫 wave spring washers GB95518 DIN186 T型方颈螺栓 T-head bolts with square neck GB37-8819 DIN188 T型双接头螺栓 T-head bolts with double nip20 DIN258 螺纹圆锥销 taper pins with threaded end ISO873721 DIN261 T型头螺栓 T-head bolts22 DIN315AF 蝶型螺母(美制) wing nuts amercia form23 DIN315DF 蝶型螺母(德制) wing nuts germany form GB62-8824 DIN316AF 蝶型螺钉(美制) wing screws amercia form25 DIN317DF 蝶型螺钉(德制) wing screws germany form26 DIN319 圆球型盖型螺母 ball knobs27 DIN404 开槽带孔球面圆柱头螺钉 slotted capstan screws GB832-8828 DIN417 开槽长圆柱端紧定螺钉 slotted set srews with full dog point ISO7435 GB75-8529 DIN427 开槽平端紧定螺钉(半牙) slotted set srews with chamfered end ISO2342 GB73-8530 DIN431 小六角特薄细牙螺母 pipe nuts with thread GB808-8831 DIN432 外舌止动垫圈 external tap GB856-8832 DIN433 小垫圈(用于圆柱头螺钉) washers for cheese head screws ISO7092 GB848-9533 DIN434 方斜垫圈(U型) square taper washers for U-section GB852-8834 DIN435 方斜垫圈(I型) square taper washers for I-sections GB852-8835 DIN436 方垫圈 square washers36 DIN438 开槽凹端紧定螺钉 slotted set with cup point ISO7436 GB74-8537 DIN439 六角薄螺母 hexagon thin nuts ISO4035 GB6172-8638 DIN439 细牙六角薄螺母 hexagon thin nuts ISO8675 GB6173-8639 DIN440 木螺钉专用垫圈 rounds washers for wood constructions ISO709440 DIN443 密封帽 sealing caps,push-in type41 DIN444 活节螺栓B 型 eye bolts form B GB798-8842 DIN462 内舌止动垫圈 internal tab washers43 DIN463 双耳止动垫圈 washers with two taps GB855-8844 DIN464 滚花高头螺钉 knurled thumb screws with collar GB834-8845 DIN465 开槽滚花高头螺钉 slotted knurled thumb screws with collar46 DIN466 滚花高螺母 knurled thumb nuts with collar GB806-8847 DIN467 滚花薄螺母 knurled thumb thin nuts GB807-8848 DIN470 锁紧垫圈 sealing washers49 DIN471 轴用弹性挡圈 retaining rings for shafts(external),circlips GB894.1-8650 DIN472 孔用弹性挡圈 retaining rings for bores(internal),circlips GB893.1-8651 DIN478 方头带垫螺栓 square head bolts with collar52 DIN479 方头圆柱底端螺栓 square head bolts with half dog point53 DIN480 方头带垫半圆底端螺栓 square head bolts with collar,half dog point and rounded end54 DIN508 T型槽螺母 T-slot nuts ISO29955 DIN525 单头螺柱 single end studs56 DIN529 地脚螺栓 masonry bolts GB799-8857 DIN546 带槽圆螺母 slotted round nuts GB817-7658 DIN547 端面带孔圆螺母 round nuts with drilled holes in one faceGB815-8859 DIN551 开槽平端紧定螺钉 slotted sit screws with flat point ISO4776 GB73-8560 DIN553 开槽锥端紧定螺钉 slotted set screws with cone point ISO7434 GB71-8561 DIN555 六角螺母 hexagon nuts ISO403462 DIN557 方螺母-C square nuts GB39-8863 DIN558 六角头螺钉 hexagon screws ISO401864 DIN561 六角头圆柱端紧定螺钉 hexagon set screws with full dog point65 DIN562 薄型方螺母-B square nuts without bevel(pressed nuts)66 DIN571 六角头木螺钉 hexagon head wood screws (coach screws) GB102-8667 DIN580 吊环螺钉 lifting eye bolts ISO3266 GB825-7668 DIN582 吊环螺母 lifting eye nuts69 DIN601 六角头螺栓 hexagon bolts ISO401670 DIN603 大半圆头方颈螺栓(马车螺栓) mushroom head square neck bolts (carriage bolts) ISO8677 GB14-8871 DIN604 沉头带插销马车螺栓 flat countersunk nib bolts72 DIN605 沉头长方颈马车螺栓 flat countersunk long square neck bolts73 DIN607 半圆头带插销马车螺栓 cup head nib bolts74 DIN608 沉头短方颈马车螺栓 flat countersunk short square neck bolts75 DIN609 六角头精配螺栓（长螺纹） hexagon fitted bolts,long thread76 DIN610 六角头精配螺栓（短螺纹） hexagon fitted bolts,short thread77 DIN653 滚花平头螺钉 knurled thumb screws thin type GB835-8878 DIN660 半圆头铆钉 round head rivets ISO1051 GB867-8679 DIN661 沉头铆钉 contersunk head rivets ISO1051 GB869-8680 DIN662 半沉头铆钉 raised contersunk head rivets ISO105181 DIN674 大扁头铆钉 mushroom head rivets ISO105182 DIN703 重型侧面带孔圆螺母 adjusting rings,heavy range (shafting collars)83 DIN705 侧面带孔圆螺母 adjusting rings,light range (shafting collars) GB816-8884 DIN741 卡头 wire rope clips85 DIN787 T型槽螺钉 T-slot screws ISO29986 DIN835 双头螺柱（牙长=2D） studs-metal (end=2d) GB900-8887 DIN906 内六角锥型闭锁螺钉 hexagon socket pipe plugs,conical thread88 DIN908 内六角直型闭锁螺钉 hexagon socket screw plugs,cyl. thread89 DIN909 外六角锥型闭锁螺钉 hexagon head pipe plugs,conical thread90 DIN910 外六角直型闭锁螺钉 hexagon head screw plugs,cyl.thread91 DIN911 内六角扳手 socket wrenches ISO293692 DIN912 内六角圆柱头螺钉 hexagon socket cap screws ISO4762 GB70-8593 DIN913 内六角平端紧定螺钉 hexagon socket set screws with flat point ISO4026 GB77-8594 DIN914 内六角尖端紧定螺钉 hexagon socket set screws with cone point ISO4027 GB78-8595 DIN915 内六角圆柱端紧定螺钉 hexagon socket set screws with dog point ISO4028 GB79-8596 DIN916 内六角凹端紧定螺钉 hexagon socket set screws with cup point ISO4029 GB80-8597 DIN917 薄型盲螺母 hexagon cap nuts98 DIN920 开槽小圆柱头螺钉 slotted short cheese head screws99 DIN921 开槽大圆柱头螺钉 slotted large cheese head screws GB838-88 100 DIN923 开槽圆柱头轴肩螺钉 slotted pan head screws with shoulder GB830-88101 DIN927 开槽无头轴肩螺钉 slotted shoulder screws102 DIN928 焊接方螺母 square weld nuts GB/T13680-92103 DIN929 焊接六角螺母 hexagon weld nuts GB/T13681-92104 DIN931 六角头螺栓（半牙） hexagon head screws ISO4014 GB5782-86 105 DIN933 六角头螺栓（全牙） hexagon head screws ISO4017 GB5783-86 106 DIN934 六角头螺母(1型) hexagon full nuts ISO4032 GB6170-86107 DIN934 细牙六角头螺母(1型) hexagon full nuts ISO8673 GB6171-86 108 DIN935 开槽六角螺母 hexagon slotted and castle nuts ISO7035GB6178-86109 DIN936 六角头薄螺母 hexagon thin nuts ISO4035 GB6172.1-86110 DIN937 六角头开槽薄螺母 hexagon thin slotted and castle nuts ISO7038 GB6181-86111 DIN938 双头螺距（牙长=1D） studs metal (end=1d) GB897-88112 DIN939 双头螺距（牙长=1.25D） studs metal (end=1.25d) GB898-88113 DIN940 双头螺距（牙长=1.5D） studs metal (end=1.5d)114 DIN960 六角头细牙螺栓（半牙） hexagon head bolts,metric fine pitch thread ISO8765 GB5785-86115 DIN961 六角头细牙螺栓（全牙） hexagon head bolts,metric fine pitch thread ISO8676 GB5786-86116 DIN962 头部穿孔六角头螺栓 additional shapes and versions for bolts 117 DIN963 开槽沉头螺钉 slotted countersund head screws ISO 2009 GB68-85 118 DIN964 开槽半沉头螺钉 slotted raised countersunk oval head screws ISO 2010 GB69-85119 DIN965 十字槽沉头螺钉 cross recessed countersunk head screws ISO7046 GB819-85120 DIN966 十字槽半沉头螺钉 cross recessed raised countersunk head screws ISO7047 GB820-85121 DIN970 六角头螺母 hexagon nuts type-1122 DIN971 六角头螺母 hexagon nuts type-2123 DIN972 细牙六角头螺母(2型) hexagon nuts with fine thread ISO8674 GB6176-86124 DIN975 牙条(全螺纹) threaded rods(studdings) GB15389-94125 DIN976 螺纹销 threaded pins(stud bolts)126 DIN979 六角头开槽薄螺母（2型） hexagon thin slotted and castle nuts 127 DIN980 全金属六角锁紧螺母（1型） prevailling torque type hexagon nuts,all metall nuts ISO7199 GB6184-86128 DIN981 圆螺母 locknuts ISO2982 GB812-88129 DIN982 六角头尼龙锁紧螺母 prevailling torque type hexagonnuts,heavy type ,with nylon insert ISO7040 GB889.1-86130 DIN985 六角头薄型尼龙锁紧螺母 prevailling torque type hexagon nuts,heavy type ,with nylon insert ISO10511 GB6172.2-86131 DIN986 六角盖型尼龙锁紧螺母 prevailling torque typedomed capnuts with nylon insert132 DIN988 配合垫片 shim rings133 DIN1052 木材连接用垫片 washers for timber connectors134 DIN1151 沉头钢钉 round plain head nails135 DIN1440 销钉专用垫片A型 plain washers for clevis pins(A型) ISO8738 136 DIN1441 销钉专用垫片 plain washers for clevis pins137 DIN1444 带头销钉 clevis pins with head ISO2341138 DIN1471 圆锥型槽销 grooved pins,taper grooved ISO8744 GB/T13829.2 139 DIN1472 圆锥型槽销(半槽) grooved pins,taper grooved half length ISO8745 GB/T13829.2140 DIN1473 平行槽销(带倒角) grooved pins,parallel grooved full lengthISO8740141 DIN1474 前端凹槽槽销 grooved pins,reserve grooved half lengthISO8741142 DIN1475 中部凹槽槽销 grooved pins,centre grooved ISO8742143 DIN1476 圆头槽销 grooved pins with round head ISO8746 GB/T13829.3 144 DIN1477 沉头槽销 grooved pins with countersunk head ISO8747145 DIN1479 六角螺母棒 turnuckles(centre parts),made out of hexagon bar 146 DIN1480 花篮螺栓 turnuckles with eye bolt and hook bolt147 DIN1481 弹性圆柱销 spring pins,heavy type ISO8752 GB879-86148 DIN1587 组合式盖型螺母 hexagon domed cap nuts GB802-88149 DIN1804 开槽圆螺母（配合沟头扳手） slotted round nuts for hook spanner 150 DIN1816 圆螺母（带插销孔） round nuts with set holes151 DIN2093 盘型弹簧垫圈 disc springs152 DIN3017 喉箍 hose clamps153 DIN3404 润滑油嘴（旋扭头） lubricating nipples,button head154 DIN3567 管夹 shackles for conduilts155 DIN3570 U型螺栓 stirrup bolts(U-bolts)156 DIN6319 球面垫圈 spherical washers,conical seats GB849-88157 DIN6325 圆柱销 parallel pins ISO8734158 DIN6330 厚六角螺母 hexagon nuts ,1.5d GB56-88159 DIN6331 厚六角法兰面螺母 hexagon nuts ,1.5d with collar GB6177-86 160 DIN6334 长六角螺母 hexagon nuts ,3d161 DIN6797-A 外齿锁紧垫圈 external teeth lock washers GB862.1-87162 DIN6797-I 内齿锁紧垫圈 internal teeth lock washers GB861.1-87163 DIN6798-A 外锯齿锁紧垫圈 external teeth serrated lock washersGB862.2-87164 DIN6798-I 内锯齿锁紧垫圈 internal teeth serrated lock washersGB861.2-87165 DIN6799 开口挡圈 retaining rings for shafts(E-rings),circlipsGB896-76166 DIN6885 平键（A型） parallel keys(form A ) ISO773/2491167 DIN6888 半圆键 woodruff keys ISO3912168 DIN6899 嵌环（支撑环） thimbles169 DIN6900 机器螺钉和垫圈组合件 screws and washers assembliesGB9074.1-.17170 DIN6901 自攻螺钉和垫圈组合件 tapping screws and washers assemblies GB9074.18-.23171 DIN6912 薄型带孔内六角圆柱头螺钉 hexagon socket head cap screws with hole,low head172 DIN6914 大六角头螺栓 hexagon head bolts with large head(friction grip bolts)173 DIN6915 大六角螺母 hexagon nuts with large wideth acrossflat(friction grip nuts)174 DIN6916 大垫圈 round washers for friction grip bolts175 DIN6917 楔型方垫圈 spuare taper washers for friction grip bolts on T-sections176 DIN6923 六角法兰面螺母 hexagon flange nuts ISO4161 GB6177-86177 DIN6925 全金属六角锁紧螺母(2型） prevailing torque type hexagon nuts,all metallic nuts ISO7042 GB6185.1-2000178 DIN7337 开口型抽芯铆钉（沉头、扁圆头） blind rivets GB12617/12618 179 DIN7338 扁平头半空心/全空心铆钉 rivets for brake and clutch lining GB875/975-86180 DIN7343 螺旋夹紧销 spiral pins ISO8750181 DIN7346 轻型弹性圆柱销 spring pins,light type ISO13337182 DIN7349 重型弹性圆柱销用垫圈 washers for bolts with heavy type spring pinss183 DIN7500 ISO公制螺纹螺钉(多种头型) threadforming screws forISO-metric thread184 DIN7504 自攻自钻螺钉(多种头型) self-drilling tapping screws185 DIN7513 开槽切削螺纹螺钉(多种头型) thread cutting screws186 DIN7516 十字槽切削螺纹螺钉(多种头型) thread cutting screws cross recess187 DIN7965 T型四爪螺母 tee nuts with pronge188 DIN7968 钢结构用六角头螺栓连接副 hexagon head fitted bolts for steel structures GB1228/1229/1230189 DIN7971 开槽盘头自攻螺钉 pan head tapping screws with slot ISO1481 GB5282-85190 DIN7972 开槽沉头自攻螺钉 countersunk flat head tapping screws with slot ISO1482 GB5283-85191 DIN7973 开槽半沉头自攻螺钉 raised countersunk oval head tapping screws with slot ISO1483 GB5284-85192 DIN7976 六角头自攻螺钉 hexagon tapping screws ISO1479 GB5285-85 193 DIN7980 圆柱头螺钉用弹簧垫圈 spring lock washers for screws with cylindrical heads ISO8738194 DIN7981 十字槽盘头自攻螺钉 pan head tapping screws with cross recessed ISO 7049 GB845-85195 DIN7982 十字槽沉头自攻螺钉 countersunk flat head tapping screws with cross recessed ISO7050 GB846-85196 DIN7983 十字槽半沉头自攻螺钉 raised countersunk oval head tapping screws with cross recessed ISO7051 GB847-86197 DIN7984 薄型内六角圆柱头螺钉 hexagon socket head cap screws with，reduced head198 DIN7985 十字槽盘头螺钉 pan head screws with cross recessed ISO7045 GB818-85199 DIN7989 钢结构用垫圈 washers for steel structures GB1230-84200 DIN7990 钢结构用六角头螺栓 hexagon head bolts for steel structures GB1229-84201 DIN7991 内六角沉头螺钉 hexagon socket countersunk head screwsISO10642202 DIN7993 轴用钢丝挡圈 roundwire snap rings for shafts GB895.2-86 203 DIN7995 十字槽半沉头木螺钉 cross recessed raised countersunk head wood screws GB952-86204 DIN7996 十字槽圆头木螺钉 cross recessed round head wood screws GB950-86205 DIN7997 十字槽沉头木螺钉 cross recessed countersunk head wood screws GB951-86206 DIN8140 螺纹护套（普通\自锁等） ciol inserts,coarse,fine thread,silf locking207 DIN9021 大外径垫圈 washers,outside diameter appro.3d ISO7093GB96-85208 DIN11024 弹簧卡子 spring cotter for a bolt209 DIN13257 平板螺栓 belting bolts (elevator bolts)210 DIN18182 干壁钉（墙板钉） dry wall screws211 DIN28129 环型螺母 lifting nuts(eye nuts) GB63-88212 DIN70952 圆螺母用止退垫圈 tab washers for slotted round nuts GB858-渗碳和渗氮常识钢的渗碳---就是将低碳钢在富碳的介质中加热到高温(一般为900--950C),使活性碳原子渗入钢的表面,以获得高碳的渗层组织。

最全緊固件中英文對照，外貿必備詞典！一、緊固件 Fasteners標準緊固件 Standard Fasteners非標準緊固件 Nonstandard Fasteners特殊緊固件 Special Fasteners汽車緊固件 Automotive Fasteners銅制緊固件 Brass Fasteners航天用緊固件 Aerospace Fasteners精密緊固件 Precision Fasteners化學緊固件 Chemical Fasteners摩托車緊固件 Motorcycle Fasteners不銹鋼緊固件 Stainless Steel Fasteners鐵道緊固件 Railway Fasteners防松緊固件 Self-locking Fasteners高強度緊固件 High strength FastenersPEM緊固件 PEM Fasteners鋼結構緊固件 Steel Structural Fasteners壓鉚緊固件 Self-Clinching Fasteners鋁制緊固件 Aluminum Fasteners鈦合金緊固件 Titanium Alloy Fasteners尼龍緊固件 Nylon Fasteners精制緊固件 Finished Fastener粗制緊固件 Unfinished Fastener螺紋緊固件 Threaded Fastener半精制緊固件 Semi-Finished Fastener抗剪緊固件 Shear Fastener抗拉緊固件 Tension Fastener面板緊固件 Panel Fasteners二、螺栓 Bolts六角頭螺栓Hexagon Head Bolts六角法蘭面螺栓Hexagon Flange Bolts軌道螺栓（魚尾螺絲）Track Bolts高強度螺栓 High Strength Bolts地腳螺栓Eyelet Bolts馬車螺栓 Carriage Bolts護攔螺栓 Guardrail Bots焊接螺栓 Weld Bolts雙頭螺栓 Double End Bolts鋼結構連接副 Structural Bolting內六角螺栓 Hex Socket Bolts合金鋼螺栓 Alloy Steel Bolts方頭螺栓 Square Head Bolts/Square Bolts鉤頭螺栓 Hook Bolts不銹鋼螺栓 Stainless steel Bolts異型螺栓 Special Bolts吊環螺栓 Lifting Eye Bolts汽車螺栓 Automotive Bolts法蘭螺栓 Flange Bolts輪胎螺栓 Wheel BoltsT型螺栓 T Bolts扁頭螺栓 Pan Head Bolts蝶形螺栓 Wing Bolts沉頭螺栓 Countersunk Bolts沉頭方頸螺栓 Countersunk Square Neck Bolts帶榫螺栓 Cup head Nib Bolts沉頭雙榫螺栓 Flat Countersunk Double Nib Bolts活節螺栓 Eye Bolts壓鉚螺栓 Clinching Bolts紅打螺栓 Hot Forging Bolts圓頭螺栓 Round Head Bolts圓頭方頸螺栓 Round Head Square Neck Bolts圓頭雙榫螺栓 Round Head Fin Neck Bolts米制圓頭方頸螺栓 Metric Round Head Square Neck BoltsT型帶孔螺栓 T bolts withHole六角頭鉸制孔用螺栓 Hexagon Fit Bolts六角頭螺桿帶孔螺栓 Hexagon Bolts with split pin hole on shank鋼網架螺栓球節點用高強度螺栓 High Strength Bolts for joints ofspace grid structures 基礎螺栓 Foundation BoltsU型螺栓 U Bolts高張力螺栓 High Strength Bolts大尺寸螺栓 Big Size Bolts螺椿栓 Stud Bolts拉栓 Blind Bolts重型六角頭螺栓 Heavy Hex Bolts大頭馬車螺栓 Step Bolts扭矩控制螺栓 T.C. Bolts蛋形頸軌道用螺栓 Elliptic Neck Track Bolts調節螺栓，調節螺釘 Pitch-Adjustable Bolts and Screws加長非標雙頭螺栓 Lengthen Non-Standard Stud Bolts電梯膨脹螺栓 Elevator Expansion Bolts三、螺釘 Screws六角螺釘Hex Head Cap Screws/Hex Screws六角機械螺釘 Hex Head Machine Bolts六角法蘭螺釘 Hex Flange Screws內六角孔螺絲 Hex Socket Cap Screws內六角沉頭螺釘 Hex Socket Flat Countersunk Head Cap Screws緊定螺釘/固定螺釘 Set Screws止付螺釘Socket Set Screws方頭緊定螺釘 Square Head Slotted Head Set Screws翼形螺釘/蝶形螺釘 Wing Screws精密螺釘 Precision Screws自攻螺釘 Self-Tapping Screws自削螺釘 Thread Cutting Screws鉆尾螺釘 Self-Drilling Screws旋入螺釘 Drive Screws機械螺釘 Machine Screws木螺釘 Wood Screws家具螺釘 Furniture Screws纖維板釘/塑板螺釘 Chipboard Screws墻用螺釘 Drywall Screws剪力釘(焊接螺釘) Welding Studs螺絲附華司組合 Screws And Washers Assembled (Sems)銅螺釘 Brass Screws鋁螺釘 Aluminum Screws合金鋼螺釘 Alloy Steel Screws組合螺釘 SEM screws電子螺釘 Electronic Screws微小精密螺釘 Micro Screws塑料螺釘 Plastic Screws復合材料用螺釘 Particle Board Screws鈦合金螺釘 Titanium Alloy Bolts鈦、鋯、鉬、鈮等螺絲、零件、材料 Ti ,Zr ,Mo, Nb Pare Metal Bolts Parts 拇指螺絲 Thumb Screws飛機特殊扣件 Source Control Bolts電梯螺釘 Elevator Screws四角頭固定螺釘 Square Set Screws單向螺釘 One Way Lag Screws管夾螺釘 Hose Clamp Screws不銹鋼固定螺釘 Stainless Steel Hex Socket Cap Screws不銹鋼內六角螺釘 Stainless Steel Hex Socket Cap Screws鉸鏈螺釘 Hinge Screws貨柜螺釘 Container Screws復合材料鉆尾螺釘 Bi-Metal Self Drilling Screws三角牙螺釘 Tri-lobular Thread Screws高低牙螺釘 High Low Screws夾板用螺釘 Particle Board Screws馬桶螺釘 Toilet Closet Bolts特長螺釘 Special Longer Screws建業螺釘 Building Fasteners不銹鋼六角螺絲 Stainless Steel Hex Socket Cap Screws不銹鋼特殊螺釘 Special Stainless Steel Screws寬牙螺釘（粗牙螺釘） Coarse Thread Screws鏈帶螺釘 Collated Screws水泥螺釘 Concrete Screws板模螺釘 Construction Bolts鋅蝶螺釘 Die Cast Wing Screws; Zinc Alloy重型車釘 Heavy Duty Wheel Hub Bolts內六角固定螺釘 Hex Socket Set Screws復合材料用螺釘（夾板用） Particle Board Screws犁壁螺釘 Plow Bolts不銹鋼木螺絲 Stainless Steel Wood Screws套掛螺栓及螺釘 Toggle Bolts鈦合金膨脹螺釘 Titanium Alloy Expansion Bolts不銹鋼高低牙螺釘 Stainless Steel High-Low Thread Screws不銹鋼機械螺釘 Stainless Steel Machine Screws不銹鋼鉆尾螺釘 Stainless Steel Self Drilling Screws不銹鋼自攻螺釘 Stainless Steel Self Tapping Screws不銹鋼自削螺釘 Stainless Steel Thread Cutting Screws不銹鋼三角牙螺釘 Stainless Steel Tri-Lobular Thread Screws 不銹鋼寬牙螺釘 Stainless Steel Coarse Thread Screws開槽沉頭螺釘 Slotted Flat Countersunk Head Machine Screws 開槽盤頭螺釘 Slotted Pan Head Machine Screws十字槽盤頭螺釘 Cross Recessed Pan Head Machine Screws 滾花頭臺階螺釘 Knurled Thurmb Screws六角頭木螺釘 Hexagon Head Wood Screws平頭滾花螺釘 Knurled Thin Thumb Screws四、螺母/螺帽 Nuts六角螺母 Hexagon Nuts六角蓋形螺母 Hex Cap Nuts六角鋸齒螺母 Hex Serrated Nuts六角法蘭螺母 Hex Flange Nuts六角平面螺母 Hex Flat Nuts六角厚螺母Hex Thick Nuts重型六角開槽螺母 Heavy Hexagon Slotted Nuts高腳螺母 Hex Coupling Nuts (High Nuts)圓螺母 Round Nuts四角螺母/四方螺母 Square Nuts四方焊接螺母 Square Weld Nuts四爪螺母Four-Claw Nuts管用螺母 Pipe Nuts輪殼螺母 Wheel Nuts蝶型螺母 Wing NutsU形螺母 U NutsT形螺母 T Nuts環首螺母 Eye Nuts齒形螺母 Kep Nuts齒花螺母 Clinch Nuts焊接螺帽 Weld Nuts壓鉚螺母 Self-clinching Nuts高張力螺母 High Strength Nuts建業用螺母 Structural Nuts不銹鋼螺母 Stainless Steel Nuts銅螺母 Brass Nuts鋁螺母 Aluminum Nuts合金鋼螺母 Alloy Steel Nuts重型車螺母 Heavy Duty Wheel Hub Nuts鐵器焊接袋帽 Acorn Cap Nuts金屬預置扭矩式螺母 All-Metal Prevailing Torque Type Nuts壁虎螺母 Anchor Nuts大尺寸螺母 Big Size Nuts鐵蓋袋帽 Closed End Acorn Nuts盤形華司螺母 Conical Washer Nuts鐵蓋+尼龍圈組合蓋帽 Din 986 Domed Cap Nuts法蘭尼龍蓋帽 Flange Nylon Insert Lock Nuts平面華司螺母 Flat Washer Nuts六角割溝螺母 Hex Slotted Nuts自鎖螺母 Self-Locking Nuts制止螺母 Sliding NutsSLN-自動防松螺母 SLN Self-Locking Nuts特殊螺母 Special Nuts彈簧螺母 Spring Nuts不銹鋼法蘭螺母 Stainless Steel Flange Nuts不銹鋼六角輪緣尼龍螺母 Stainless Steel Flange Nylon Insert Lock Nuts 不銹鋼六角重型螺母 Stainless Steel Heavy Hex Nuts不銹鋼六角螺母 Stainless Steel Hex Nuts不銹鋼尼龍嵌入螺母 Stainless Steel Nylon Insert Lock Nuts普通六角螺母 Hex Nuts六角重型螺母 Heavy Hex Nuts薄型螺母 Hex Jam Nuts尼龍嵌入防松螺母 Nylon Insert Lock Nuts尼龍鎖緊螺母Nylon Cage Nuts機械螺絲用六角螺母 Hex Machine Screw Nuts米制六角開槽螺母 Metric Slotted Hex Nuts軌道螺栓用方螺母 Track Bolt Nuts米制六角金屬鎖緊螺母 Prevalling Torque Hexagon Nuts開槽螺母Slotted Round Nuts六角開槽薄螺母Hexagon Slotted Thin Nuts五、螺柱 Studs壓鉚螺柱 Self-Clinching Studs銅螺柱 Brass Studs焊接螺柱 Weld Studs雙頭螺柱 Double End Studs六角螺柱 Hex Studs支撐卡柱 Self-Clinching Standoffs六、墊圈 Washers彈簧墊圈 Spring Washers/Spring Lock Washers寬型彈簧墊圈 Extra-duty Helical Spring Lock Washers杯型墊圈 Cup washers波形墊圈 Wave Washers內齒墊圈 Internal Tooth Washers外齒墊圈 External Tooth Washers銅墊圈 Copper Washers方墊圈 Square Washers密封墊圈 Sealing Washers碟形彈簧墊圈 Disc Spring Washers外舌止動墊圈External Tab Washers高強度墊圈 High strengthen washers橡膠墊圈 Rubber Washers鎖緊墊圈 Lock Washers平墊圈 Plain Washers鞍型彈性墊圈 Curved Spring Washers鋸齒鎖緊彈性墊圈 Toothed lock washers外鋸齒鎖緊墊圈 Serrated Lock Washers錐形墊圈 Taper Washers重型彈簧墊圈 Heavy Spring Lock Washers尼龍墊圈 Nylon Washers淬硬鋼墊圈 Hardened Steel Washers七、鉚釘 Rivets平頭鉚釘 Flat Head Rivets擊芯鉚釘 Drive Rivets彩色鉚釘 Colored Rivets沉頭鉚釘 Countersunk Head Rivets半沉頭鉚釘 Oval Countersunk Head Rivets平錐頭鉚釘 Cone Head Rivets抽芯鉚釘 Blind Rivets開口鉚釘 Split Rivets開口型抽芯鉚釘 Open End Blind Rivets拉鉚釘 Pop Rivets封閉鉚釘Closed End Rivets封閉性抽芯鉚釘 Sealed Type Blind Rivets塑料鉚釘 Plastic Rivets空心鉚釘 Tubular Rivets環槽鉚釘 Ring Groove Rivets單鼓型鉚釘 Single-Grip Rivets圓頭鉚釘 Round Head Rivets高沉頭鉚釘 Countersunk Head Rivets鋁鉚釘 Aluminum Rivets實心鉚釘 Solid Rivets沉頭實心鉚釘 Countersunk Head Solid Rivets燈籠鉚釘 Lantern Blind Rivets半空心鉚釘 Semi-Tubular Rivets圓頭半空心鉚釘 Semi-tubular Pan Head Rivets異型鉚釘 Special Rivets不銹鋼鉚釘 Stainless Steel Rivets雙鼓型鉚釘 Multi-grip Rivets高強度鉚釘 High Strength Rivets臺階鉚釘 Step Rivets面板鉚釘 Tablet Rivets開花型抽芯鉚釘 Flowering Blind Rivets拉花型抽芯鉚釘 Peel Type Blind Rivets溝槽型抽芯鉚釘 Grooved Type Blind Rivet鉚接工具 Riveting Tool八、壁虎（膨脹螺栓）Anchors/Expansion Bolts化學錨栓 Chemical Anchors打入式壁虎 Hammer Drive Anchors內迫壁虎 Drop in Anchors重型壁虎 Heavy Duty Anchors錘釘壁虎 Hit Anchors中空壁虎 Hollow Wall Anchors套管壁虎 Sleeve Anchors插片壁虎 Ceiling Anchors門窗、地板專用壁虎 Nylon Frame Anchors or Metal frame Anchors電梯壁虎 Bolt Anchors車修壁虎 Wedge Anchors魚眼壁虎 Tie Wire Anchors外迫壁虎 Cut Anchors塑料膨脹 Plastic Anchors不銹鋼重載脹栓 Heavy Duty Expansion Anchors象腳壁虎 Elephant Foot Anchors長型蘭花夾 Short Strap Anchors九、銷 Pins開口銷 Split Pins圓錐銷 Taper Pins鎖銷 Lock Pins銷軸 Clevis Pins with head槽銷 Grooved Pins彈性銷 Spring Pins圓柱銷 Parallel Pins彈性圓柱銷 Slotted Spring Pins帶孔銷 Pins with split pin hole十、擋圈 Circlips/Rings開口擋圈 E rings孔用擋圈 Circlips for holes軸用鋼絲擋圈 Roundwire Snap Rings for shaft軸肩擋圈Rings for shoulder夾緊擋圈 Grip Rings軸用卡簧 Circlips for shafts帶齒軸用擋圈 Retaining Rings with Lugs for shafts鋼絲鎖圈 Round wire Circlips錐形鎖緊擋圈 Lock Rings with cone pins十一、其他 Others牙條 Threaded Rod沖壓件 Stampings平鍵 Parallel Keys半圓鍵 Woodruff Keys扳手 Spanners鋼絲螺套 Wire Thread Insert自動車床車削件 CNC Turning Parts齒輪 Gears模具 Molds線材盤元 Iron or steel wire rod鉸鏈 Hinge表面處理 Surface Treatment。

No.xx简写中文1 screw scr螺丝2 nut nut螺母3 washer wash垫圈4 head hd头5 thread thre螺纹6 coating coat镀层7 rivet riv铆钉8 standoff stdoff内外六角钉9 driver driv穴10 hexagon hexa六角11 tooth tooth齿12 lock lck锁13 spring spr弹簧14 wave wave波浪型15 pitch pitch牙距16 partial thread PT半螺纹17 PT PT一种螺纹形式18 Full Thread FT全螺纹19 silver silv银20 cone cone锥形21 Eco-syn Eco 30度牙的一种螺纹22 ThreadForming TF自攻螺纹23 Self Tapping self tapp自切屑螺纹24 pin pin销25 shaft Shaf轴26 steel St铁27 stainless steel SS不锈钢28 Brass(Cu) Bras(Cu)铜29 Aluminum AL铝30 Rubber Rub橡胶31 machine screw mech scr机制螺丝32 SEM screw SEM Scr组合螺丝33 Material material材料34 Grade GD等级35 Finish Finish表面处理36 Point Point点37 Clamp Clam夹子38 internal Int内39 external ext外40 thickness /厚度41 length /xx42 hole /xx43 Metric Metcric公制44 DIN /德标45 ANSI /美标46 JIS /日标螺丝相关参数英语对照A: Machine Screw:机械螺丝B: Tapping Screw:自攻螺丝(分使用于金属与使用于塑料二种) B-1: Sheet Metal Tapping Screw. (铁板牙自攻螺丝)B-2: Plastic Tapping Screw. (塑料用,自攻螺丝)C: Wooden Screw :木工螺丝D: Drywall Screw :水泥墙螺丝常见螺丝材质:a.Low Carbon Steel :低碳钢b. SS-304 : Stainless Steel 304c. SS-302: Stainless Steel 302 :结构韧性较好d. Aluminum 5052 :铝合金5052d. Brass:xxe. Bronze:青铜f. UNS C11000 Copper:锑铜Finish Code:外观处理规格Head Code:头部外型螺丝型号Drive Code:头部剖沟,特征型号Length Code:螺丝长度(mm)A-1: Thread Code:螺丝型号A-2: Length Code:螺丝长度:A-3: Drive Code/头部剖沟,特征.a. Slotted:一字( Minus )b. Phillips:十字( Plus )c. Phil-Slot:一字/十字d. Hex Scoket:xxe. One Way:单向(只可锁入,不可退出)A-4: Head Code/头部外型.a. Flat:平头(锁入后,顶部与工作件齐平)b. Oval:色拉头c. Round:圆头d. Pan:圆扁头e. Truss:大圆扁头f. Hex :六角头A-5: Finish Code/外观处理.a. Z: Zine-Plated:镀锌b. Ni: Ni-Plated:镀镍c. Tin-Plated:镀锡d. Zine Plated / Green Iridite:镀锌绿膜处理.e. Radiant Plated:镀五彩f. Passivate:抗氧化处理.g. Alodial Finish:无外观处理螺纹大径：Major Diam螺纹中径：Pitch diam螺纹底径：Minor diam通止规：Go/No go gage机械性能：mechanical and physical propertiesunified thread统一英制螺纹Lustrate hydrogen after galvanizing to avoid hydrogen embrittlement镀后去氢，防止氢脆Case carburization表面渗碳With across flats对边With across corners对角Radius of fillet:头下圆角Transition thread length过度螺纹Wrenching height扳拧高度Rockwell铬氏硬度Vickers维氏硬度Brinellxx氏硬度Metallography microscope金相显微镜Salt spray device盐雾试验箱Tensile testing machine拉力试验机Cold forming冷打Hot forging红镦P C 8 = property class 8机械性能8级原材料：Raw material球化退火：Annealing冷拔：Drawingxx：Forming机加工：Machining螺纹成型：Roll Threading热处理：heat-treatment表面处理：finish去氢：Lustrating hydrogen检验：Inspection包装：Packing入库：Stocking车床：lathe磨制：grinding红打：hot forging冲压：punchingDiameter直径Lengthxx各类紧固件标准件产品xx对照插片壁虎Steel Ceiling Anchors内迫壁虎Drop in Anchors碳钢锤钉壁虎Steel Hit Anchors碳钢六角螺帽Steel Hex Coupling Nuts强力xx壁虎Wedge Anchors外迫壁虎Cut Anchors化学壁虎Chemical Anchors不锈钢重载胀栓Heavy Duty Expansion Anchors鱼眼壁虎企眼长螺帽Tie Wire Anchors锌合金打入式壁虎Hammer Drive Anchors弹簧螺帽Strut Nuts兰花夹系列Toggle Bolts (Spring Toggle & Gravity Toggle)门窗、地板专用壁虎Nylon Frame Anchors or Metalframe Anchors石膏板中空壁虎Hollow Wall Anchors套管式壁虎Sleeve Anchors打入式壁虎鱼形尼龙壁虎Nylon Frame Harmmer Fixing (Nylon Hammer Drive Anchors)强力式锤钉壁虎Hit Anchors电梯壁虎Bolt Anchors重载壁虎Heavy duty anchors两片夹Loxin Masonry Anchors定位螺栓Set Bolts长型兰花夹Short Strap Anchors工具棒Drop in Setting Tools象脚壁虎Elephant foot anchors水泥预埋件Concrete Insert翻边胀轴Drop in Anchor with Lip冲件Legs Drywall Anchors六角盖头螺帽Hex Cap Nuts六角锯齿螺帽Hex Serrated Nuts六角轮缘螺帽Hex Flange Nuts高脚螺帽Hex Coupling Nuts(High Nuts) 圆螺帽Round Nuts四角螺帽Square Nuts管用螺帽Pipe Nuts轮壳螺帽Wheel Nuts蝶型螺帽Wing NutsU形螺帽U NutsT形螺帽T Nuts环首螺帽Eye Nuts齿形螺帽Kep Nuts齿花螺帽Clinch Nuts耐候钢六角重型螺帽Corten Steel Heavy Hex Nuts焊接螺帽Weld Nuts高张力螺帽Heigh Strength Nuts建业用螺帽Structural Nuts不锈钢螺帽Stainless Steel Nuts铜螺帽Brass Nuts铝螺帽Aluminum Nuts合金钢螺帽Alloy Steel Nuts重型车螺帽Heavy Duty Wheel Hub Nuts铁器焊接袋帽Acorn Cap Nuts金属预置扭矩式螺帽All-Metal Prevailing Torque Type Nuts 壁虎螺帽Anchor Nuts大尺寸螺帽Big Size Nuts铁盖袋帽Closed End Acorn Nuts盘形华司螺帽Conical Washer Nuts铁盖+尼龙圈组合盖帽Din 986 Domed Cap Nuts突缘尼龙盖帽Flange Nylon Insert Lock Nuts平面华司螺帽Flat Waser Nuts六角割沟螺帽Hex Slotted Nut自锁螺帽Self-Locking Nuts制止螺帽Sliding NutsSln-自动防松螺帽Sln Self-Locking Nuts其它特殊螺帽Special Nuts弹簧螺帽Spring Nuts不锈钢突缘螺帽Stainless Steel Flange Nuts不锈钢六角轮缘尼龙螺帽Stainless Steel Flange Nylon Insert Lock Nuts 不锈钢六角重型螺帽Stainless Steel Heavy Hex Nuts不锈钢六角螺帽Stainless Steel Hex Nuts不锈钢尼龙嵌入螺帽Stainless Steel Nylon Insert Lock Nuts普通六角螺帽Hex Nuts六角重型螺帽Heavy Hex Nuts薄型螺帽Hex Jam Nuts尼龙嵌入防松螺帽Nylon Insert Lock Nuts机械螺丝用六角螺帽Hex Machine Screw Nut六角螺丝(栓) Hex Head Cap Screws(Hex Bolts)六角机械螺丝Hex Head Machine Bolts六角xx螺丝Hex Lag Bolts四角螺丝Square Head BoltsT头螺丝T Head Bolts环首螺丝Eye Bolts内六角孔螺丝Hex Socket Cap Screws 固定螺丝Set Screws螺椿栓Stud Bolts螺旋椿Screw Studs轮壳螺栓Wheel Bolts翼形螺丝Wing Screws自攻螺丝Self Tapping Screws自削螺丝Thread Cutting Screws钻尾螺丝Self Drilling Screws旋入螺丝Drive Screws机械螺丝Machine Screws木螺丝Wood Screws家具螺丝Furniture Screws塑板螺丝Chipboard Screws墙用螺丝Drywall Screws基础螺栓Foundation BoltsU型螺栓U Bolts勾头螺栓Hook Bolts套挂螺丝Toggle Bolts轨道螺栓(鱼尾螺丝) Track Bolts耐候钢螺丝Corten Steel Heavy Hex Bolts扭矩控制螺栓T.C.Bolts高张力螺栓High Strength Bolts剪力钉(焊接螺丝) Welding Studs螺丝附华司组合Screws And Washers Assembled(Sems)大尺寸螺栓Big Size Bolts不锈钢小螺丝Stainless Steel Sheet Metal Screws不锈钢大螺丝Stainless Steel Bolts铜螺丝Brass Screws铝螺丝Aluminum Screws合金钢螺丝Alloy Steel Screws电子螺丝Electronic Screws微小精密螺丝Micro Screws塑料螺丝Plastic Screws复合材料用螺丝Particle Board Screws钛合金螺丝Titanium Alloy Bolts钛、锆、钼、铌等螺丝、零件、材料Ti,Zr,Mo,Nb Pare Metal Bolts Parts 拇指螺丝Thumb Screws双头牙螺丝Double End Screws Hanger Bolt车辆(汽车)螺丝、螺帽Automotive Fasteners航天用螺丝Aerospace Fasteners飞机特殊扣件Source Control BoltsxxBlind Bolts面板螺丝Panel Fasteners电梯螺丝Elevator Bolts四角头固定螺丝Square Set Screws大头马车螺丝Step Bolts单向螺丝One Way Lag Screws管夹螺丝Hose Clamp Screws不锈钢固定螺丝Stainless Steel Hex Socket Cap Screws 不锈钢内六角螺丝Stainless Steel Hex Socket Cap Screws 铰链螺丝Hinge Screws货柜螺丝Container Screws复合材料钻尾螺丝Bi-Metal Self Drilling Screws三角牙螺丝Trilobular Thread Screws高低牙螺丝High Low Screws夹板用螺丝Particle Board Screws马桶螺丝Toilet Closet Bolts特长螺丝Special Longer Screws建业螺丝Building Fasteners不锈钢六角螺丝Stainless Steel Hex Socket Cap Screws 其它特殊螺丝Special Screws Or Bolts不锈钢特殊螺丝Special Stainless Steel Screws宽牙螺丝（粗牙螺丝）Coarse Thread Screws链带螺丝Collated Screws水泥螺丝Concrete Screws板模螺丝Construction Bolts锌蝶螺丝Die Cast Wing Screws; Zinc Alloy重型车螺丝Heavy Duty Wheel Hub Bolts内六角固定螺丝Hex Socket Set Screws复合材料用螺丝（夹板用）Particle Board Screws犁壁螺丝Plow Bolts不锈钢木螺丝Stainless Steel Wood Screws套挂螺栓及螺丝Toggle Bolts钛合金膨胀螺丝Titanium Alloy Expansion Bolts六角盖头螺帽Hex Cap Nuts六角锯齿螺帽Hex Serrated Nuts六角轮缘螺帽Hex Flange Nuts高脚螺帽Hex Coupling Nuts(High Nuts)圆螺帽Round Nuts四角螺帽Square Nuts管用螺帽Pipe Nuts轮壳螺帽Wheel Nuts蝶型螺帽Wing NutsU形螺帽U NutsT形螺帽T Nuts环首螺帽Eye Nuts齿形螺帽Kep Nuts齿花螺帽Clinch Nuts耐候钢六角重型螺帽Corten Steel Heavy Hex Nuts焊接螺帽Weld Nuts高张力螺帽Heigh Strength Nuts建业用螺帽Structural Nuts不锈钢螺帽Stainless Steel Nuts铜螺帽Brass Nuts铝螺帽Aluminum Nuts合金钢螺帽Alloy Steel Nuts重型车螺帽Heavy Duty Wheel Hub Nuts铁器焊接袋帽Acorn Cap Nuts金属预置扭矩式螺帽All-Metal Prevailing Torque Type Nuts 壁虎螺帽Anchor Nuts大尺寸螺帽Big Size Nuts铁盖袋帽Closed End Acorn Nuts盘形华司螺帽Conical Washer Nuts铁盖+尼龙圈组合盖帽Din 986 Domed Cap Nuts突缘尼龙盖帽Flange Nylon Insert Lock Nuts平面华司螺帽Flat Waser Nuts六角割沟螺帽Hex Slotted Nut自锁螺帽Self-Locking Nuts制止螺帽Sliding NutsSln-自动防松螺帽Sln Self-Locking Nuts其它特殊螺帽Special Nuts弹簧螺帽Spring Nuts不锈钢突缘螺帽Stainless Steel Flange Nuts不锈钢六角轮缘尼龙螺帽Stainless Steel Flange Nylon Insert Lock Nuts 不锈钢六角重型螺帽Stainless Steel Heavy Hex Nuts不锈钢六角螺帽Stainless Steel Hex Nuts不锈钢尼龙嵌入螺帽Stainless Steel Nylon Insert Lock Nuts锌压属螺帽Zinc Die Casting Nuts普通六角螺帽Hex Nuts六角重型螺帽Heavy Hex Nuts薄型螺帽Hex Jam Nuts尼龙嵌入防松螺帽Nylon Insert Lock Nuts机械螺丝用六角螺帽Hex Machine Screw Nut合金钢线材盘元Alloy Steel Wire Rod球状化线材Annealing Wire And Rod黑铁丝Black Wire黄铜棒线Brass Wire And Rod磨光棒钢Bright Steel Bar(Hex/Round/Square)铜合金线Copper Alloy Wire线切割线E.D.M Cutting Wire快削钢线材盘元Free Cutting Steel Wire Rod线材Iron Or Steel Wire线材盘元Iron Or Steel Wire Rod洋白铜线Nickel Silver Wire磷青铜线Phosphate Bronze Wire不锈钢条棒Stainless Steel Bar(Round/Hex/Square)不锈钢冷锻线材Stainless Steel Cold Heading Wire不锈钢线(抽线后) Stainless Steel Draw Wire不锈钢线材Stainless Steel Wire不锈钢线材及盘元Stainless Steel Wire And Rod棒钢Steel Bar(Hex/Round/Square)转回90度碾线头机90讧evolving Wire Twisting Machine 气动拉钉机Air Riveter各式螺丝类产品自动包装Automatic Packaging For All Kinds Of Packaging 自动包装机Automatic Packing Machine螺丝制造搓牙机械Automatic Thread Rolling Machine螺丝割尾加工机械Automatic Thread Slotting Machine螺丝制造成型机械Automatic Trimming Machine拉钉打头机Blind Rivet Heading Machine螺丝、螺帽成型机Bolt Formers,Nuts Formers,Headers螺丝、螺帽热处理Bolt Nut And Screws Heat Treatment螺丝、螺帽热处理炉Bolt Nut And Screws Heat Treatment Furnaces球状化电器炖炉Carburizing Furnace Vacuum And Bell Type Furnace超防锈复合瓷膜Ceramic Coating连续式光辉渗碳淬火炉Continuous Bright Carburizing Quenching Furnace 连续式光辉调质淬火炉Continuous Bright Hardening Quenching Furnace 中、高热镀锌光辉连续炉Continuous Bright Heat Treat Furnace连续式光辉热处理炉Continuous Type Bright Heat Treatment Furnace螺丝割尾及特殊割遘加工Machine Screw Shank Slotting螺丝钻孔加工Screw Shank Drilling鸡眼上下模Eyelets Dies一般线材、盘元、退火炉General Wire,Wire Rod,Annealing Furnace倒立式滑落型伸线机Handstand Type Wire Drawing Machine十字冲模Header Punches In Various Drives成型冲模Header Punches In Various Drives螺丝打头机Heading Machine螺丝制造高速搓牙机械High Speed Automatic Thread Rolling Machine高中低周波感应加热炉High,Medium,Low Frequency Induction Heater 空心打头机Hollow Heading Machine热浸镀锌螺丝、螺帽Hot Dip Galvanizing Bolts And Nuts机械镀锌Mechanical Galvanized迷你成型机Mini-Formers成品自动收线机Non-Stop Coiler精抽自动收线机Non-Stop Coiler(Skinpass)螺帽模Nut Forming Dies螺帽成型模Nuts Formers特殊零件成型机Parts Forming Maching冲模Punch Dies冲子Punch Pins罗拉成型机Rollers Formers机(踏)车用螺丝成型机Screw For Motorcycle Or Bicycle Heading Machine 止付螺丝成型机Set Screws Formers套高成型机Sockets Formers一般线材、盘元、螺丝合金炖炉Spheroidizing Bright Annealing Furnace 球状化热处理炉Spheroidizing Heat Treatment Furnace攻牙机Tapping Machine螺丝攻、车刀、模具Taps Dies And Tools搓牙机铁屑分离装置Thread Chip Separator滚牙轮Thread Rolling Dies牙板Thread Rolling Dies Plates精密油压滚牙机Hydraulic Thread Rolling Machines模具Tools六角整头模Trimming Dies Hexagan碳化钨模具Tungsten Carbide Die镀钛处理(Tin)专业加工服务Tin Hard Coating For Cutting Tools And Punch By Pvd电镀化学原料Various Electroplating Chemicals环规校正Calibration For Ring Gage环规、牙规、三线规校正Calibration For Ring Gage, Athread Gage, 3 Wire Gage螺丝、螺帽品检量测仪器Fasteners Inspection And Measurement Instruments螺丝、螺帽成型攻牙专用油Forming And Tapping Oils For Bolts And Nuts Formers螺丝、螺帽五金等检验Insptection Services For Fasteners And Hardware德国schatz扭力机代理Representative Of Schatz Torque MachinIso品质保证系统Iso Quality Assurance System生产管理系统Production Control System物料管理系统Material Control System齿轮Gears不锈钢牙条棒Stainless Steel Hread Rod 马达轴承轴心组件Bearing Shaft(Motor) 轴承轴心Bearing Shaft开口铆钉Blind Rivets长形拉帽Blind Rivet Nuts拉帽Blind NutsxxBlind Rivets实心梢Clevis Pins And Straight Pins弹片Clips卷钉Coil Nails冷锻零件Cold Forming Part开口销Cotter PinsE型环E-Rings膨胀螺栓Expansion Anchor Bolts鸡眼钉Eyelets RivetsR型销Snap Pins闸、锁Latches And Keeper Assembleds 其它特殊铆钉Other Specil Rivets销Pins格式管夹、管束Pipe Hanger铆钉Rivets螺旋锔及螺旋圈Screw Hook And Screw Rings中空钉Semi-Tubular Rivet开叉钉Split Drive Anchors弹簧华司Spring Washers弹簧蝴蝶夹Spring Wings不锈钢华司Stainlesssteel Washers钢铁钉Steel And Iron Nails搓牙铁钉Thread Nails钛合金铆钉Titaium Alloy Rivets管形铆钉Tubular Rivets华司Washers真空热处理Vacuum Heat Treatment螺丝、螺帽、五金、Diy扣件Fasteners合金钢工具Alloy Steel Tools螺栓模Bolt Heading Dies手动xx钳Hand Riveter船舶链Anchor Chain脚踏车链锁Bicycle Chain Locks螺丝起子Bit罗拉Chain Roller特殊铆合扣件Collars(A Blindfastener For Huck Intl)装饰链Decorative Chains自攻螺纹衬套Ensat Threaded Inserts六角扳手Hexagon Keys超音螺纹压入式螺纹自动锁扣Threaded Inserts For Plastic Injection Mouldeings汽车特殊杆接件Special Auto-Mobile Fastener As Your Needs螺纹护套Recoil Inserts链条用滚子Roller For Roller Chain金属板镶嵌组件及自动夹扣组件Sheet Metal Fasteners工具套筒组件Socket Wrench Sets不锈钢链Stainless Steel Chains轭子T-Yoke轮胎链Tire Chains狗链Dog Chains喇叭头轭铁U-Yoke,T-Yoke For Speaker不锈钢输送带轮用轨道Stainless Wheel's Rack For Transporter工业用链Industrial Steel Link Chains拖链安全链Tow Chains And Safety Chains机车离合器零件Manufacture Of Motorcycle's Cvt Parts牙条棒Thread Rod机(踏)车用螺丝、轴心Screws And Shafts For Motorcycle Or Bicycle 针车用螺丝、轴心Screws And Shafts For Sewing Maching止付螺丝Socket Set Screws不锈钢宽牙螺丝Stainless Steel Coarse Thread Screws不锈钢高低牙螺丝Stainless Steel High-Low Thread Screws 不锈钢机械螺丝Stainless Steel Machine Screws不锈钢钻尾螺丝Stainless Steel Self Drilling Screws不锈钢自攻螺丝Stainless Steel Self Tapping Screws不锈钢自削螺丝Stainless Steel Thread Cutting Screws不锈钢三角牙螺丝Stainless Steel Tri-Lobular Thread Screws。

英文名称对应标准Square head bolts GB/T 8-88 C 级Flat countersunk square neck bolts GB/T 10-88 沉头沉带榫螺栓Flate countersunk nib bolts GB/T 11-88 (大)半圆头方颈螺栓Cup head square neck (with large head)bolt GB/T 14/15-88六角头铰制孔用螺栓Hexagon fit boltsGB/T 27-88 A 和B 级六角头螺杆带铰制孔用螺栓(细杆)Hexagon fit bolts with split pin hole on shank(Reduced shank) GB/T 28-88 A 和B 级十字槽凹穴六角头螺栓Cross recessed hexagon bolts with indentation GB/T 29.2-88 A 和B 级六角头头部带孔螺栓Hexagon bolts with wire holes on head GB/T 32.1-88 A 和B 级T 型槽用螺栓Bolt for T-slot GB/T 35.1-88 B 级加强半圆头方颈螺栓Strengthened cap head square neck bolts GB/T 794.1-93 活节螺栓Eye bolts GB/T798-88地角螺栓Eyelet bolts GB/T799-88头角头螺栓Hexagon head bolts GB/T5780-2000 C 级六角头法兰面螺栓Hexagon flange bolts GB/T5789-86 B 级外六角花法兰面螺栓Steel hexalobular head bolt with small flangeDIN 34801-9918.久美特Geomet 19.耐落Nylok 陆锈宝Rupst 20.翡丽雅特 ViridAct 21.美加力Magni 沉头方劲螺栓中文名称一.孔别三.常用名称1.螺丝类方头螺栓1.割沟Slotted2.十字穴 Phillips3.米字穴 Pozidriv(cross recess)4.十字割沟 Slotted phillips5.四角孔Square6.十字方孔 Square phillips7.六角孔hexagon8.方孔割沟Square slotted9.梅花穴Six-lobe 10.三角孔Triangle 11.Y 型槽Y-type 12.斜Y 槽Tri-wing 13.五等角5-Point 二,电镀1.电镀锌Zinc plated2.白皮Plain finished3.五彩Yellow zinc plated4.镀镍Nickel plated5.热浸锌Hot dip galvanized6.黑锌Black zinc plated7.镀黑Black finished8.染黑Black oxide9.(黑)磷酸盐(black)Phosphated 10.黄铜 Brass 11.镀青蓝Unichrome plated 12.古铜A.C Brontze 13.青古铜Antique brass 14.机械镀锌Mechanical galvanized 15.绿锌Green zinc plated 16.电锌腊Zinc plated&waxed 17.达克锈Dacrotizing plated英文名称对应标准双头螺柱bm=1d Double end studs-bm=1d GB/T 897-88等长双头螺柱 B 级Double end studs(clamping type)-product grade A GB/T 901-88螺杆Thread rods GB/T 15389-943.螺钉类英文名称对应标准开槽圆柱头螺钉Slotted cheese head screws GB/T65-2000开槽沉头螺钉Slotted countersunk flat head screws (common head style) GB/T68-2000 eqv ISO 2009-94开槽半沉头螺钉Countersunk slotted raised head screws(common head style)GB/T69-2000 eqv ISO 2010-94内六角圆柱头螺钉Hexagon socket head cap screws GB/T70.1-2000 eqv ISO 4762.2-97内六角平圆头螺钉Hexagon socket button head screws GB/T70.2-2000 eqv ISO 7380-97内六角沉头螺钉Hexagon socket countersunk head screws GB/T70.3-2000 eqv ISO 10642-97十字槽盘头螺钉Pan head screw with cross recess GB/T818-2000 eqv ISO 7045-94十字槽半沉头螺钉Countersunk raised head screws(common head style)with cross recess GB/T820-2000 eqv ISO 7047-94十字槽圆柱头螺钉Cheese head screws with cross recess GB/T822-2000 eqv ISO 7048-94滚花高头螺钉Knurled thumb screws GB 834-88滚花平头螺钉Knurled screws GB 835-88内六角花形盘头螺钉Hexagon lobular socket pan head scerws GB 2672-86内六角圆柱头轴肩螺钉Hexagon socket head shoulder scerws GB/T 5281-854.自攻螺钉 英文名称对应标准十字槽盘头盘自攻螺钉Cross recessed pan head tapping screws GB 845-85十字槽沉头盘自攻螺钉Cross recessed countersunk head tapping screws GB 846-85十字槽盘头盘自攻锁紧螺钉Cross recessed pan head thread forming screws GB 6560-86十字槽凹穴六角头自攻螺钉Cross recessed hexagon head tapping screws with indentationGB 9456-98十字槽自攻螺钉-刮削端(用于精密机械)cross recessed tapping screws-scrape point(fasters for fine mechanics)GB/T 13806-2墙板自攻螺钉Dry wall screws GB/T14210-93十字槽盘头自钻自攻螺钉Cross recessed pan head self-drilling tapping screws GB/T15856.1-95六角凸缘自攻螺钉Hexagon head tapping screws with collarGB/T16824.1-97 eqv ISO 7053-92中文名称中文名称中文名称英文名称对应标准方螺母-C 级Square nuts-product grade C GB/T39-88六角螺母-C 级Hexagon nuts-product grade C GB/T41-2000eqv ISO 4034-99六角厚螺母Hexagon thick nuts GB/T56-88六角薄螺母Hexagon thin nuts GB/T6172.1-2000eqvISO 4035-99蝶形螺母Wing nuts GB/T 62-88组合式盖形螺母Acorn nutsGB/T 802-88球面六角螺母Hexagon nut with raised face GB/T 804-88滚花高螺母kunrled nut with collarGB/T 806-881型非金属嵌件六角锁紧螺母Prevailing torque type hexagon nuts(with non-metallic insert).style 1GB/T889.1-2000eqv 7040-97盖形螺母Acorn nutsGB/T 923-88六角薄螺母 无倒角Hexagon thin nuts (unchamfered)GB/T6174-2000eqvISO 4036-99六 角法兰面螺母Hexagon nuts with flangeGB/T6177.1-2000eqv ISO 4161-991型六角开槽螺母Hexagon slotted and castle nuts.style1GB/T 6178-86全金属六角锁紧螺母Prevailing torque type all-metal hexagon nuts GB/T 6184-2000eqv ISO 7719-97焊接方螺母square weld nut GB/T 13680-92焊接六角螺母Hexagon weld nuts GB/T 13681-92平头铆螺母Flat head riveted nuts GB/T 17880.1-996.挡圈 英文名称对应标准锥销锁紧挡圈Lock ring with corne pin GB/T 883-86轴肩挡圈Rings for shouderGB/T 891-86螺钉紧固轴端挡圈Lock rings at the end of shaft with screw GB/T 893.1-86孔用弹性挡圈-A 型Circlips for holes -typeA GB/T 894.1-86轴用弹性挡圈Circlips for shaft -typeA GB/T 895-2-86开口挡圈"E"ringsGB/T 896-86钢丝锁圈Round coire circlips GB/T 921-86夹紧挡圈Crip ringsGB/T 960-86中文名称中文名称英文名称对应标准弹簧垫圈(标准型)Single coil spring lock washers (normal type)GB/T 93-87平垫圈-C 级Plain washersGB/T 95-85eqv ISO 7091-2000大平垫圈Plain washers-large series GB/T 96-85 A 和B 级鞍形弹性垫圈Curved spring washers GB/T 860-87内齿锁紧垫圈Lock washers internal teethGB/T 861.1-87内锯齿锁紧垫圈Serrated lock washers internal teeth GB/T 861.2-87外锯齿锁紧垫圈Serrated lock washers external teeth GB/T 862.2-87波型弹性垫圈Wave spring washersGB/T 955-87锥形锁紧垫圈Countersunk external toothed look washersGB/T 956.1-87锥形锯齿锁紧垫圈Countersunk serrated external toothed lock washers GB/T 956.2-878.销英文名称对应标准开口销Split pins GB/T 91-2000eqvISO1234-97圆锥销Taper pinsGB/T 117-2000eqvISO2339-86螺纹圆柱销Paraller pins with external thread GB/T 878-86销轴Clevis pins with head GB/T 882-86平头铆钉Flat head rivetsGB/T 109-86平锥头铆钉（粗制）Cone-head rivets-black GB/T 864-86空心铆钉Tubular rivetsGB/T 876-86封闭型扁圆头抽芯铆钉Mushroom head break mandred closed end blind rivets GB/T 12615-90开口型沉头抽芯铆钉120 deg flush head break mandrel blind rivetsGB/T 12617-90中文名称中文名称9.紧固件-组合件和连接副英文名称对应标准中文名称钢结构用高强度大六角头螺栓High strength bolts with large hexagon head for steel structures GB/T1230-91钢结构用高强度大六角头螺母High strength large hexagon nuts for steel stuctures GB/T1229-91钢结构用高强度大六角头垫圈High strength plain washers for steel structures GB/T1230-91钢结构用扭剪型高强度螺栓连接副Sets of torshear type high strength bolt hexagon nut and plain washer for steel structures GB/T3632-95十字槽盘头螺钉,弹簧垫圈和平垫圈组合件Cross recessed pan head screw ,single coil spring lock washer and plain washer assemblies GB/T 9074-.4-88无头焊钉Headless for stud welding GB/T 10432-89圆柱头焊钉Cheese head studs for stud welding GB/T 10433-89机械焊接螺钉Weld screws with metric thread DIN 34817-2001。

紧固件中英文对照大全-------------------------------------------------------------------------------- 螺栓－－方头螺栓 C级 UDC 621.882.6 | GB 8-88 | 代替 GB8-76 Square head bolts-Product grade C－－沉头方颈螺栓 UDC 621.882.6 | GB 10-88 | 代替 GB10-76 Flat countersunk square neck bolts－－沉头带榫螺拴 UDC 621.882.6 | GB 11-88 | 代替 GB11-76 Flat countersunk nib bolts－－半圆头方颈螺栓 UDC 621.882.6 | GB 12-88 | 代替 GB12-76 Cup head square neck bolts－－半圆头带榫螺栓 UDC 621.882.6 | GB 13-88 | 代替 GB13-76 Cup head nid bolts－－大半圆头方颈螺栓 C级 ISO 8677:1986 | GB 14-1998 | 代替 GB14-88 Cup head square neck bolts with large head-Product grade C－－大半圆头带榫螺栓 UDC 621.882.6 | GB 15-88 | 代替 GB15-76 Cup head nib bolts with large head－－六角头铰制孔用螺栓 UDC 621.882.6 | GB 27-88 | 代替 GB27-76 Hexagon fit bolts-product grade A and B－－六角头螺杆带孔铰制孔用螺栓 UDC 621.882.6 | GB 28-88 | 代替 GB28-76 Hexagon fit bolts with split pin hole on shank-product grade A and B－－六角头头部带槽螺栓 A 和 B 级 UDC 621.882.6 | GB 29.1-88 | 代替 GB29-76 Hexagon bolts with slot on head -product A and B－－十字槽凹穴六角头螺栓 UDC 621.882.6 | GB 29.2-88 | 代替 GB29-76 Cross recessed hexagon bolts with indentation－－六角头螺杆带孔螺栓 UDC 621.882.6 | GB 31.1-88 | 代替 GB31、23、24-76 Hexagon bolts with split pin hole on shank-product grade A and B－－六角头螺杆带孔螺栓细杆 B级 UDC 621.882.6 | GB 31.2-88 | 代替 GB31、23、24-76 Hexagon bolts with split pin hole on shank-Reduced shank-product grade B－－六角头螺杆带孔螺栓细牙 A和B级 UDC 621.882.6 | GB 31.3-88 | 代替 GB31、23、24-76Hexagon bolts with split pin hole on shank-Fine pitch thread-product grade A and B －－六角头头部带孔螺栓 A 和 B级 UDC 621.882.6 | GB 32.1-88 | 代替GB32、25、26-76 Hexagon bolts with wire holes on head-product grade A and B－－六角头头部带孔螺栓细杆 B级 UDC 621.882.6 | GB 32.2-88 | 代替 GB32、25、26-76 Hexagon bolts with wire holes on head-Reduced shank-product grade B－－六角头头部带孔螺栓细牙 A 和 B 级 UDC 621.882.6 | GB 32.3-88 | 代替GB32、25、26-76Hexagon bolts with wire holes on head-Fine pitch thread-product grade Aand B －－下方头螺栓 B级 UDC 621.882.6 | GB 35-88 | 代替 GB35-76 Square head bolts with small head-praduct grade B－－T 形槽用螺栓 UDC 621.882.6 | GB 37-88 | 代替 GB37-76 Bolts for T-Slot－－加强半圆头方颈螺栓 GB /T794-93 | 代替 GB794-671Strengthened cup head square neck bolts－－活节螺栓 UDC 621.882.6 | GB 798-88 | 代替 GB798-76 Eye bolts－－地脚螺栓 UDC 621.882.6 | GB 799-88 | 代替 GB799-76 Eyelet bolts－－沉头双榫螺 UDC 621.882.6 | GB 800-88 | 代替 GB800-77 Flat countersunk double nib bolts－－小圆半头低方颈螺栓 B级 ISO 8678:1988 | GB /T 801-1998 | 代替 GB801-88 Cup head square neck bolts with small head and short neck-product grade B－－六角头螺栓 C级 ISO 4016:1999 | GB /T 5780-2000 | 代替 GB/T 5780-1986 Hexagon head bolts-product grade C－－六角头螺栓全螺纹 C级 ISO 4018:1999 | GB /T 5781-2000 | 代替 GB/T5781-1986 Hexagon head bolts-Full thread-product grade C－－六角头螺栓 ISO 4014：1999 | GB /T 5782-2000 | 代替 GB/T 5782-1986 Hexagon head bolts－－六角头螺栓全螺纹 ISO 4017：1999 | GB /T 5783-2000 | 代替 GB/T 5783-1986 Hexagon head bolts-Full thread－－六角头螺栓-细杆-B级 UDC 621.882.6 | GB 5784-86 | 代替 GB30、21-76 Hexagon head bolts-Reduced shank -Product grade B－－六角头螺栓细牙 ISO 8765：1999 | GB /T 5785-2000 | 代替 GB/T 5785-1986 Hexagon head bolts with fine pitch thread－－六角头螺栓细牙全螺纹 ISO 8676：1999 | GB /T 5786-2000 | 代替 GB/T 5786-1986 Hexagon head bolts with fine pitch thread-Full thread－－六角法兰面螺栓-加大系列-B级 UDC 621.882.6 | GB 5789-86 | Hexagon flange bolts-Heavy series-product grade B－－六角法兰面螺栓-加大系列-细杆-B级 UDC 621.882.6 | GB 5790-86 | Hexagon flange bolts-Heavy series-product grade B－－六角法兰面螺栓小系列 ISO 4162：1990 | GB /T 16674-1996 | 代替 GB/T 5787、5788-1986Hexagon flange bolts-Small series－－钢网架螺栓球节点用高强度螺栓 GB /T 16939-1997 | High strength bolts for joints of space grid structures 螺柱－－双头螺柱 bm=1d UDC 621.882 | GB 897-88 | 代替 GB897-76 Double end studs-bm=1d－－双头螺柱 bm=1.25d UDC 621.882 | GB 898-88 | 代替 GB898-76 Double end studs-bm=1.25d－－双头螺柱 bm=1.5d UDC 621.882 | GB 899-88 | 代替 GB899-76 Double end studs-bm=1.5d－－双头螺柱 bm=2d UDC 621.882 | GB 900-88 | 代替 GB900-76 Double end studs--bm=2d－－等长双头螺柱 B级 UDC 621.882 | GB 901-88 | 代替 GB901-762Double end studs(clamping type) -Product grade B－－手工焊用焊接螺柱 GB 902.1-89 | 代替 GB902-76 Weld studs for manualwelding－－机动弧焊用焊接螺柱 GB 902.2-89 | 代替 GB902-76 Weld studs for arcwelding－－储能焊用焊接螺柱 GB 902.3-89 | 代替 GB902-76 Weld studs for capacitor discharge welding－－等长双头螺柱 C级 UDC 621.882 | GB 953-88 | 代替 GB953-76 Double endstuds(clamping type)-product grade C －－螺杆 GB /T 15389-94 | Threaded rods 螺母－－方螺母 C级 UDC 621.882.3 | GB 39-88 | 代替 GB39-76 Square nuts-product grade C－－六角螺母 C级 ISO 4034：1999 | GB /T41-2000 | 代替 GB/T 41-1986 Hexagon nuts-product grade C－－六角厚螺母 ISO 621.882.3 | GB 56-88 | 代替 GB56-76 Hexagon thick nuts－－蝶形螺母 UDC 621.882.3 | GB 62-88 | 代替 GB62-76 Wing nuts－－环形螺母 UDC 621.882.3 | GB 63-88 | 代替 GB63-76 Lifting nuts－－组合式盖形螺母 UDC 621.882.3 | GB 802-88 | 代替 GB802-76 Acorn nuts－－球面六角螺母 UDC 621.882.3 | GB 804-88 | 代替 GB804-76 Hexagon nutswith raised face－－扣紧螺母 UDC 621.882.3 | GB 805-88 | 代替 GB805-76 Tight nuts－－滚花高螺母 UDC 621.882.3 | GB 806-88 | 代替 GB806-76 Knurled nut with collar－－滚花薄螺母 UDC 621.882.3 | GB 807-88 | 代替 GB807-76 Knurled nuts－－小六角特扁细牙螺母 UDC 621.882.3 | GB 808-88 | 代替 GB808-76 Small hexagon thin nuts-Fine pitch thread－－嵌装圆螺母 UDC 621.882.3 | GB 809-88 | 代替 GB809-76 Lnsert round nuts－－小圆螺母 UDC 621.882.3 | GB 810-88 | 代替 GB810-76 Small round nuts－－圆螺母 UDC 621.882.3 | GB 812-88 | 代替 GB812-76 Round nuts－－端面带孔圆螺母 UDC 621.882.3 | GB 815-88 | 代替 GB815-76 Round nuts with drilled holes in one face3－－侧面带孔圆螺母 UDC 621.882.3 | GB 816-88 | 代替 GB816-79 Round nuts with set pin holes in side－－带槽圆螺母 UDC 621.882.3 | GB 817-88 | 代替 GB817-76 Slotted round nuts－－1型非金属嵌件六角锁紧螺母 ISO 7040：1997 | GB /T 889.1-2000 | 代替GB/T 889-1986Prevailing torque type hexagon nuts(with non-metallic insert),style 1－－1型非金属嵌件六角锁紧螺母细牙 ISO 10512：1997 | GB /T 889.2-2000 |Prevailing torque type hexagon nuts(with non-metallic insert),style 1,with fine pitch thread －－盖形螺母 UDC 621.882.3 | GB 923-88 | 代替 GB923-76 Acorn nuts－－1型六角螺母 ISO 4032：1999 | GB /T 6170-2000 | 代替 GB/T 6170-1986 Hexagon nuts,style 1－－1型六角螺母细牙 ISO 8673：1999 | GB /T 6171-2000 | 代替 GB/T 6171-1986 Hexagon nuts,style 1,with fine pitch thread－－六角薄螺母 ISO 4035：1999 | GB /T 6172.1-2000 | 代替 GB/T 6172-1986 Hexagon thin nuts(chamfered)－－非金属嵌件六角锁紧薄螺母 ISO 10511：1997 | GB /T 6072.2-2000 | Prevailing torque type hexagon thin nuts(with non-metallic insert)－－六角薄螺母细牙 ISO 8675：1999 | GB /T 6173-2000 | 代替 GB/T 6173-1986 Hexagon thin nuts(chamfered) with fine pitch thread－－六角薄螺母无倒角 ISO 4036：1999 | GB /T 6174-2000 | 代替 GB/T 6174-1986 Hexagon thin nuts(unchamfered)－－2型六角螺母 ISO 4033：1999 | GB /T 6175-2000 | 代替 GB/T 6175-1986 Hexagon nuts,style 2－－2型六角螺母细牙 ISO 8674：1999 | GB /T 6176-2000 | 代替 GB/T 6176-1986 Hexagon nuts,style 2,with fine pitch thread－－六角法兰面螺母 ISO 4161：1999 | GB /T 6177.1-2000 | 代替 GB/T 6177-1986 Hexagon nuts with flange－－六角法兰面螺母细牙 ISO 10663：1999 | GB /T 6177.2-2000 | Hexagonnuts with flange-fine pitch thread－－1型六角开槽螺母-A和B级 UDC 621.882.3 | GB 6178-86 | 代替 GB57~58-76 Hexagon slotted and castle nuts,style 1 -product grades A and B－－1型六角开槽螺母-C级 UDC 621.882.3 | GB 6179-86 | 代替 GB57~58-76 Hexagon slotted nuts,style 1 -product grade C－－2型六角开槽螺母-A和B级 UDC 621.882.3 | GB 6180-86 | Hexagon slotted and castle nuts,style 2 -Product grades A and B－－六角开槽薄螺母-A和B级 UDC 621.882.3 | GB 6181-86 | 代替 GB59~60-76 Hexagon thin slotted nuts-Product grades A and B－－2型非金属嵌件六角锁紧螺母 ISO 7041：1997 | GB /T 6182-2000 | 代替 GB/T 6182-1986Prevailing torque type hexagon nuts(with non-metallic insert),style 2－－非金属嵌件六角法兰面锁紧螺母 ISO 7043：1997 | GB /T 6183.1-2000 | 代替GB/T 6183-19864Prevailing torque type hexagon nuts with flange(with non-metallic insert)－－非金属嵌件六角法兰面锁紧螺母细牙 ISO 12125：1997 | GB /T 6183.2-2000 |Prevailing torque type hexagon nuts with flange(with non-metallicinsert)with fine pitch thread －－1型全金属六角锁紧螺母 ISO 7719：1997 | GB /T 6184-2000 | 代替 GB/T 6184-1986 Prevailing torque type all-metal hexagon nuts,style 1－－2型全金属六角锁紧螺母 ISO 7042：1997 | GB /T 6185.1-2000 | 代替 GB/T 6185-1986 Prevailing torque type all-metal hexagon nuts,style 2－－2型全金属六角锁紧螺母细牙 ISO 10513：1997 | GB /T 6185.2-2000 | Prevailing torque type all-metal hexagon nuts,style 2,with fine pitch thread－－2型全金属六角锁紧螺母 9级 ISO 7720：1997 | GB /T 6186-2000 | 代替GB/T 6186-1986Prevailing torque type all-metal hexagon nuts,style 2-Property class 9－－全金属六角法兰面锁紧螺母 ISO 7044：1997 | GB /T 6187.1-2000 | 代替GB/T 6187-1986Prevailing torque type all-metal hexagon nuts with flange－－全金属六角法兰面锁紧螺母细牙 ISO 12126：1997 | GB /T 6187.2-2000 | Prevailing torque type all-metal hexagon nuts with flange with fine pitch thread－－1型六角开槽螺母细牙 A和B级 UDC 621.882.3 | GB 9457-88 | 代替 GB57、58-76 Hexagon slotted and castle nuts,style 1-fine pitch thread-product grades A and B －－2型六角开槽螺母细牙 A和B级 UDC 621.882.3 | GB 9458-88 |Hexagon slotted and castle nuts,style 2--Fine pitch thread -Product grades A and B－－六角开槽薄螺母细牙 A和B级 UDC 621.882.3 | GB 9459-88 | 代替 GB59、60-76 Hexagon thin slotted nuts--Fine pitch thread -Product grades A and B －－焊接方螺母 GB /T 13680-92 | Square weld nuts－－焊接六角螺母 GB /T 13681-92 | Hexagon weld nuts－－平头铆螺母 GB /T 17880.1-1999 | Flat head riveted nuts－－沉头铆螺母 GB /T 17880.2-1999 | Countersunk head riveted nuts－－小沉头铆螺母 GB /T 17880.3-1999 | Small countersunk head riveted nuts－－120°小沉头铆螺母 GB /T 17880.4-1999 | 120°Small countersunk head riveted nuts－－平头六角铆螺母 GB /T 17880.5-1999 | Flat head hexagon riveted nuts－－精密机械用六角螺母 ISO 4166：1979 | GB /T 18195-2000 | Hexagon nuts for fine mechanics 螺钉－－开槽圆柱头螺钉 ISO 1207：1992 | GB /T 65-2000 | 代替 GB/T 65-1985 Slotted cheese head screws5感谢您的阅读，祝您生活愉快。

---------------------------------------------------------------最新资料推荐------------------------------------------------------ 紧固件各类产品名称术语中英文对照表紧固件各类产品名称术语中英文对照表1.紧固件定义 1.1 紧固件Fastener 1.2 商品紧固件Commercial Fastener 1.3 标准紧固件Standard Fastener 1.4 非标准紧固件Nonstandard Fastener 1.5 特殊紧固件Special Fastener 1.6 精制紧固件Finished Fastener 1.7 粗制紧固件Unfinished Fastener 1.8 螺纹紧固件Threaded Fastener 1.9 半精制紧固件Semi-Finished Fastener 1.10 有头紧固件Headed Fastener 1.11 无头紧固件Headless Fastener 1.12 压力紧固件Compression Fastener 1.13 高强度紧固件High strength Fastener 1.14 抗剪紧固件Shear Fastener 1.15 抗拉紧固件Tension Fastener 1.16 库存紧固件Stock Fastener 2.头部型式及扳拧特征 2.1 六角头Hexagon head 2.2 六角头垫圈面Hexagon head with washer face 2.3 六角头凸缘Hexagon head with collar 2.4 六角头法兰面Hexagon head with flange 2.5 方头Square head 2.6 方头、凸缘Square head with collar 2.7 三角头Triangle head 2.8 三角头、凸缘Triangle head with collar 2.9 人角头Oct-agonal head 2.10 12角头、法兰面12 point flange head (bihexagonal head) 2.11 T型头T head ( hammer head ) 2.12 圆头Round head ( button head ) 2.13 扁圆头Mushroom head ( truss head ) 2.14 圆柱头Cheese head ( flat fillister head ) 2.15 球面圆柱头Raised cheese head ( fillister head ) 2.16 盘头Pan head 2.17 沉头1/ 11Countersunk head ( flat head) ( c s k head ) 2.18 双沉头Reinforced head ( double cone ) 2.19 半沉头Raised countersunk head ( oval head ) 2.20 球面扁圆柱头Binging head 2.21 沉头清根Undercut countersunk head ( undercut flat head ) 2.22 半沉头清根Undercut raised countersunk head ( undercut oval head ) 2.23 球体头Ball head 2.24 按纽头Button head 2.25 无头Headless 2.26 圆形垫圈头Round washer head 2.27 内六角头Socket head 2.28 高圆头High botton head 2.29 双层头Biconic head 2.30 锥头Cone head 2.31 尖锥头Steeple head 2.32 喇叭头Bugle head 2.33 薄片头thin wafer 2.34 冲压凹穴型头Drilled fillister head 2.35 伞形头Stuss head 2.36 蘑菇头Mushroom head 2.37 支承面Bearing surface 2.38 垫圈面Washer face 2.39 六角Hexagon 2.40 四方Square 2.41 三角Triangle 2.42 人角Octagon 2.43 12角12 point (bihexagonal ) 2.44 内六角Hexagon socket 2.45 内三角Triangle socket 2.46 内四角Square socket 2.47 内六花键Six-spline socket 2.48 内12角12 point socket ( bihexagon socket ) 2.49 开槽Slot 2.50 十字槽 H Cross recess ( phillips ) 2.51 十（米）字槽Cross recess ( pozidriv ) 2.52 蝶形（翼形） Wing 2.53 旋棒Tommy 2.54 直纹滚花Straight knurl 2.55 网纹滚花Diamond knurl 2.56 十字孔Cross hole ( set pin hole in side ) 2.57 五角Pentagon 2.58 梅花槽Torx recess 2.59 离合槽Clutch recess 2.60 四方槽Square recess 3.杆部及其末端---------------------------------------------------------------最新资料推荐------------------------------------------------------ 3.1 标准杆Normal shank ( nominal shank diameter=nominal thread diameter) 3.2 细杆Reduced shank ( shank diameter<minor diameter ) 3.3 腰状杆Waisted shank ( shank diameter> thread diameter )1/53/ 113.4 加强杆Increased shank ( shank diamerer> thread diameter ) 3.5 轴杆Shouder ( collar ) 3.6 方颈Square neck 3.7 榫Fin 3.8 凸缘Fillet 3.9 锯齿形Serration 3.10 肋Lug 3.11 条颈Ribbed neck 3.12 胀大颈Swell neck WINDFAST-QC.DEP. page3of12 Record 2008-3-3 No. Chinese Description in English 3.13 杆(部)体Shank 3.14 锥端Cone point 3.15 截锥端Short dog point 3.16 凹端Cup point 3.17 短圆柱端Short dog point 3.18 长圆柱端Long dog point 3.19 短圆柱球面端Short dog point with rounded end 3.20 短圆柱截锥端Short dog point with truncated cone end 3.21 刮销端Scrape point 3.22 自攻螺钉的末端End for self-tapping screws 3.23 自攻锁紧螺钉的末端End for thread rolling screws (thread formed by deformation ) 3.24 辗制末端As-roller end 3.25 平端Flat point 3.26 球面端(倒圆端) Rounded end 3.27 倒角端Chamfered end 3.28 钻孔端Gimlet point 3.29 顶锻端Header point 3.30 钉子端Nail point 3.31 针端Needle point 3.32 半圆端Oval point 3.33 导向端Pilot point 3.34 球端Spherical point 3.35 夹断端Pinck point4.尺寸及形位公差 4.1 实际尺寸Actual size 4.2 允差Allawance size 4.3 基本尺寸Basic size 4.4 设计尺寸Design size 4.5 配合Fit 4.6 尺寸极限Limits of size 4.7 公称尺寸Nominal size 4.8 参改尺寸Reference size4.9 公差Tolerance 4.10 公差位置Position tolerance 4.11 对边宽度Width across flats 4.12 对角宽度Width across corner---------------------------------------------------------------最新资料推荐------------------------------------------------------ 4.13 螺纹通(测量) Go thread gauge 4.14 螺纹止(测量) No go thread gauge 4.15 头下圆角半径Radius under head 4.16 开槽宽度Slot recess width 4.17 开槽深度Slot recess depth 4.18 十字槽插入深Penetration depth 4.19 十字槽直径Recess diameter 4.20 十字槽宽度Recess width 4.21 头部直径Head diameter 4.22 头部高度Head height 4.23 头部角度Head angle 4.24 无螺纹杆径Shank diameter ( unthreaded diameter ) 4.25 无螺纹杆长Shank length ( unthreaded length ) 4.26 夹紧长度Grip length 4.27 螺纹大径Major thread diameter 4.28 螺纹小径Minor diameter ( small ) 4.29 肩距Unthreaded length under head 4.30 螺纹长度Thread length 4.31 杆长Total length 4.32 内六角扳拧深度Depth hexagon socket 4.33 内凹槽插入深度Key engagement 4.34 外径Exter diameter ( outside diameter ) 4.35 内径Internal diameter ( inside diameter ) 4.36 长度Length 4.37 宽度Breadth 4.38 厚度Thickness 4.39 高度Hight 4.40 孔径Bore diameter 4.41 法兰直径Flange diamerer 4.42 方径长度Square neck length 4.43 方径宽度Square neck width 4.44 凸缘高度Collar height 4.45 凸缘直径Collar diameter 4.46 对称度Symmerty 4.47 同轴度Concentricity ( coaxiality ) 4.48 垂直度Perpendicularity 4.49 平行度Parallelism 4.5 直度Straightriess 4.51 槽杆同轴度Recess concentricity 4.52 头杆同轴度Head concentricity5/ 114.53 头杆垂直度Head lnclination2/5---------------------------------------------------------------最新资料推荐------------------------------------------------------ 4.54 斜度Angularity ( taper ) 4.55 弧度或弯曲度Bow or camber 4.56 尾尖角Point angle 4.57 镀锌层厚度Zinc plating thickness 4.58 跳动Run-out 4.59 锥度Taper ratio 4.60 榫长Nib length4.61 榫宽Nib width 4.62 倒角.圆角Chamfer 4.63 平面度Flatness5.机械性能 5.1 抗拉强度Tensile strength 5.2 屈服强度Proof strength 5.3 屈服点Lower yield stress 5.4 扭转强度Torque strength ( torsional strength ) 5.5 剪切强度Shear strength 5.6 冲击韧性Impact strength 5.7 延伸率Elongation 5.8 断面收缩率Reduction 5.9 拉(压)应力Tension 5.10 破坏(扭)力矩Breaking torque 5.11 晶粒度Grahularity 5.12 机械性能Mechanical properties 5.13 脱碳Decarburise 5.14 渗碳Carburization 5.15 最小剩余弹力Minimum residual sping force 5.16 压负荷的百分率Percenatage of compression load 5.17 表面硬度Surface hardness 5.18 芯部硬度Core hardness 5.19 扭矩Torque ( torsion ) 5.20 表面硬化层深度Case harden depth 5.21 氢脆Hydrogen embrittlement 5.22 压载(负)荷Compression load 5.23 硬度试验Hardness test 5.24 头部坚固性试验Head soundness test 5.25 扭转试验Twisting test 5.26 弹性试验Resilience test 5.27 保证载荷试验Proof loading test 5.28 楔负载强度试验Wedge loading test 5.29 弯曲试验Bending test 5.30 旋入试验Screw-in test 5.31 最小破坏力矩试验Torsional test and minimum torques7/ 115.32 永久变形试验Permanent deformation test 5.33 盐雾试验Salt spray test 5.34 弹性Elasticity5.35 韧性Tenacity ( Toughnee ) 5.36 塑性Fiexibility 5.37 磁力碳伤Magnetic particle inspection6.材料-热处理-表面处理 6.1 碳钢Carbon steel 6.2 低碳钢Low carbon steel 6.3 中碳钢Medium carbon steel 6.4 合金钢Alloy steel 6.5 热处理钢Heat-treated steel 6.6 低马钢Low carbon martensite steel 6.7 奥氏体不锈钢Austenitic stainless steel 6.8 马氏体不锈钢Martenitic stainless steel 6.9 铁Iron 6.10 铝Aluminium 6.11 黄铜Brass 6.12 紫铜Copper 6.13 青铜Bronze 6.14 塑料Plastic 6.15 淬火Quenched 6.16 回火Tempered 6.17 退火Annealed 6.18 表面硬化Case hardened 6.19 强度等级Class 6.20 氧化Oxide ( anodizing ) 6.21 金属Metal 6.22 非金属Metalloid 6.23 发黑Black 6.24 本色Plain ( self colour ) 6.25 热处理Heat treatment 6.26 涂层Coating 6.27 表面处理Finish 6.28 涂蜡Waxed 6.29 镀锌(兰白锌) Zinc plated ( zinc / clear ) 6.30 镀黄锌Zinc yellow ( Y.Z.P.)6.31 镀黑锌Zinc plated black 6.32 镀镍Nickel plated 6.33 镀铜Brass plated 6.34 热浸镀锌Hot dip galvanized ( H.D.G.) 6.35 电镀Electplating 6.36 机械镀锌Mechanical galvaizing 6.37 表面热处理Surface heat treatment 7、加工方法7.1 冷镦Cold heading 7.2 冷锻Cold forging 7.3 热锻Hot forging 7.4 成型Forming 7.5 切削(断) Cutting3/5---------------------------------------------------------------最新资料推荐------------------------------------------------------ 7.6 缩径Shrink diameter 7.7 搓(攻)丝Threading 7.8 滚丝Thread rolling 7.9 拔丝Drawing 7.10 酸洗Pickling 7.11 钝化Passirating 7.12 废水处理Waste water treatment 7.13 研磨Grinding 7.14 镦粗Upsetting 7.15 开槽Soltting 7.16 刮削Sharing 7.17 滚花Kunrling 7.18 抛光Polishing 7.19 冲压Punching 7.20 滚动Tumbling 7.21 精整Trimming 7.22 铣削Milled 7.23 挤压Extruding 7.24 钻孔Drilling 7.25 模压Embossing 7.26 沉孔Countersinking 7.27 压印Coining 7.28 扩孔Counterboring 7.29 控削Broaching 7.30 辊光Burnishing 7.31 锻造Forging 7.32 剪切Shear 7.33 焊接Welded 7.34 喷砂Sand blasting 8.表面缺陷 8.1 裂缝Cracks 8.2 淬火裂缝Quench cracks 8.3 锻造裂缝Forging cracks 8.4 锻造爆裂Forging bursts 8.5 剪切爆裂Shear bursts 8.6 条痕Laps 8.7 凹痕Voids 8.8 皱纹Folds ( pits ) ( laps ) 8.9 切痕Tool marks 8.10 损伤Damages 8.11 毛刺Burr 8.12 碎屑Chip 8.13 夹杂Inclusions 8.14 锈皮Sharing 8.15 飞边Flash 8.16 开裂Cracks 8.17 锈、锈斑Rust9.螺纹 9.1 普通螺纹Screw thread 9.2 锥螺纹Taper screws thread 9.3 自攻螺纹(宽牙螺纹) Tapping screws thread ( spaced thread ) 9.4 木螺钉螺纹Wood screws thread 9.5 米制螺纹Metric thread 9.6 ISO 米制螺纹ISO Metric thread 9.7 米制细牙螺纹Metric fine pitch thread 9.8 ISO 米制细牙螺纹ISO Metric fine pitch thread 9.99/ 11寸制螺纹Inch thread 9.10 统一螺纹(ISO寸制) Unified screw thread ( ISO inch ) 9.11 惠氏螺纹Whitworth thread 9.12 管螺纹Pipe thread 9.13 惠氏管螺纹Whitworth pipe thread 9.14 螺旋线Helix 9.15 螺旋面Helical surface 9.16 外螺纹External thread 9.17 内螺纹Inernal thread 9.18 牙侧Flank 9.19 沟槽Groove 9.20 凸起Ridge 9.21 牙顶Crest 9.22 牙底Root 9.23 螺纹牙型Thread profile 9.24 螺纹线Thread 9.25 单线螺纹Single--start--thread 9.26 多线螺纹Multi--start--thread 9.27 右旋螺纹Right--start--thread 9.28 左旋螺纹Left--start--thread 9.29 工作牙侧Pressure ( load ) flank 9.30 非工作牙侧Clearing ( clearance ) flank 9.31 牙底的圆角半径Root radius 9.32 牙型高度Height ( or depth ) of thread 9.33 牙型角Included angle 9.34 牙型半角Flank lead 9.35 中径线Pitch line 9.36 螺纹轴线Axis of thread 9.37 导程Flank lead 9.38 双牙导程Dual flank lead 9.39 螺距Flank pitch 9.40 双牙螺距Dual flank lead 9.41 大径Major diameter 9.42 小径Minor diameter 9.43 中径Pitch diameter4/5---------------------------------------------------------------最新资料推荐------------------------------------------------------ 9.44 9.45 9.46 9.47 9.48 9.49 9.50单一中径Simple pitch diameter 作用中径Virtual pitch diameter 螺纹升角Lead angle 基本牙型Basic profile 伞状螺纹Umbrella thread 粗牙螺纹Coarse thread 细牙螺纹Fine thread5/511/ 11。

---------------------------------------------------------------最新资料推荐------------------------------------------------------ 紧固件各类产品名称术语中英文对照表紧固件各类产品名称术语中英文对照表1.紧固件定义 1.1 紧固件Fastener 1.2 商品紧固件Commercial Fastener 1.3 标准紧固件Standard Fastener 1.4 非标准紧固件Nonstandard Fastener 1.5 特殊紧固件Special Fastener 1.6 精制紧固件Finished Fastener 1.7 粗制紧固件Unfinished Fastener 1.8 螺纹紧固件Threaded Fastener 1.9 半精制紧固件Semi-Finished Fastener 1.10 有头紧固件Headed Fastener 1.11 无头紧固件Headless Fastener 1.12 压力紧固件Compression Fastener 1.13 高强度紧固件High strength Fastener 1.14 抗剪紧固件Shear Fastener 1.15 抗拉紧固件Tension Fastener 1.16 库存紧固件Stock Fastener 2.头部型式及扳拧特征 2.1 六角头Hexagon head 2.2 六角头垫圈面Hexagon head with washer face 2.3 六角头凸缘Hexagon head with collar 2.4 六角头法兰面Hexagon head with flange 2.5 方头Square head 2.6 方头、凸缘Square head with collar 2.7 三角头Triangle head 2.8 三角头、凸缘Triangle head with collar 2.9 人角头Oct-agonal head 2.10 12角头、法兰面12 point flange head (bihexagonal head) 2.11 T型头T head ( hammer head ) 2.12 圆头Round head ( button head ) 2.13 扁圆头Mushroom head ( truss head ) 2.14 圆柱头Cheese head ( flat fillister head ) 2.15 球面圆柱头Raised cheese head ( fillister head ) 2.16 盘头Pan head 2.17 沉头1/ 11Countersunk head ( flat head) ( c s k head ) 2.18 双沉头Reinforced head ( double cone ) 2.19 半沉头Raised countersunk head ( oval head ) 2.20 球面扁圆柱头Binging head 2.21 沉头清根Undercut countersunk head ( undercut flat head ) 2.22 半沉头清根Undercut raised countersunk head ( undercut oval head ) 2.23 球体头Ball head 2.24 按纽头Button head 2.25 无头Headless 2.26 圆形垫圈头Round washer head 2.27 内六角头Socket head 2.28 高圆头High botton head 2.29 双层头Biconic head 2.30 锥头Cone head 2.31 尖锥头Steeple head 2.32 喇叭头Bugle head 2.33 薄片头thin wafer 2.34 冲压凹穴型头Drilled fillister head 2.35 伞形头Stuss head 2.36 蘑菇头Mushroom head 2.37 支承面Bearing surface 2.38 垫圈面Washer face 2.39 六角Hexagon 2.40 四方Square 2.41 三角Triangle 2.42 人角Octagon 2.43 12角12 point (bihexagonal ) 2.44 内六角Hexagon socket 2.45 内三角Triangle socket 2.46 内四角Square socket 2.47 内六花键Six-spline socket 2.48 内12角12 point socket ( bihexagon socket ) 2.49 开槽Slot 2.50 十字槽 H Cross recess ( phillips ) 2.51 十（米）字槽Cross recess ( pozidriv ) 2.52 蝶形（翼形） Wing 2.53 旋棒Tommy 2.54 直纹滚花Straight knurl 2.55 网纹滚花Diamond knurl 2.56 十字孔Cross hole ( set pin hole in side ) 2.57 五角Pentagon 2.58 梅花槽Torx recess 2.59 离合槽Clutch recess 2.60 四方槽Square recess 3.杆部及其末端---------------------------------------------------------------最新资料推荐------------------------------------------------------ 3.1 标准杆Normal shank ( nominal shank diameter=nominal thread diameter) 3.2 细杆Reduced shank ( shank diameter<minor diameter ) 3.3 腰状杆Waisted shank ( shank diameter> thread diameter )1/53/ 113.4 加强杆Increased shank ( shank diamerer> thread diameter ) 3.5 轴杆Shouder ( collar ) 3.6 方颈Square neck 3.7 榫Fin 3.8 凸缘Fillet 3.9 锯齿形Serration 3.10 肋Lug 3.11 条颈Ribbed neck 3.12 胀大颈Swell neck WINDFAST-QC.DEP. page3of12 Record 2008-3-3 No. Chinese Description in English 3.13 杆(部)体Shank 3.14 锥端Cone point 3.15 截锥端Short dog point 3.16 凹端Cup point 3.17 短圆柱端Short dog point 3.18 长圆柱端Long dog point 3.19 短圆柱球面端Short dog point with rounded end 3.20 短圆柱截锥端Short dog point with truncated cone end 3.21 刮销端Scrape point 3.22 自攻螺钉的末端End for self-tapping screws 3.23 自攻锁紧螺钉的末端End for thread rolling screws (thread formed by deformation ) 3.24 辗制末端As-roller end 3.25 平端Flat point 3.26 球面端(倒圆端) Rounded end 3.27 倒角端Chamfered end 3.28 钻孔端Gimlet point 3.29 顶锻端Header point 3.30 钉子端Nail point 3.31 针端Needle point 3.32 半圆端Oval point 3.33 导向端Pilot point 3.34 球端Spherical point 3.35 夹断端Pinck point4.尺寸及形位公差 4.1 实际尺寸Actual size 4.2 允差Allawance size 4.3 基本尺寸Basic size 4.4 设计尺寸Design size 4.5 配合Fit 4.6 尺寸极限Limits of size 4.7 公称尺寸Nominal size 4.8 参改尺寸Reference size4.9 公差Tolerance 4.10 公差位置Position tolerance 4.11 对边宽度Width across flats 4.12 对角宽度Width across corner---------------------------------------------------------------最新资料推荐------------------------------------------------------ 4.13 螺纹通(测量) Go thread gauge 4.14 螺纹止(测量) No go thread gauge 4.15 头下圆角半径Radius under head 4.16 开槽宽度Slot recess width 4.17 开槽深度Slot recess depth 4.18 十字槽插入深Penetration depth 4.19 十字槽直径Recess diameter 4.20 十字槽宽度Recess width 4.21 头部直径Head diameter 4.22 头部高度Head height 4.23 头部角度Head angle 4.24 无螺纹杆径Shank diameter ( unthreaded diameter ) 4.25 无螺纹杆长Shank length ( unthreaded length ) 4.26 夹紧长度Grip length 4.27 螺纹大径Major thread diameter 4.28 螺纹小径Minor diameter ( small ) 4.29 肩距Unthreaded length under head 4.30 螺纹长度Thread length 4.31 杆长Total length 4.32 内六角扳拧深度Depth hexagon socket 4.33 内凹槽插入深度Key engagement 4.34 外径Exter diameter ( outside diameter ) 4.35 内径Internal diameter ( inside diameter ) 4.36 长度Length 4.37 宽度Breadth 4.38 厚度Thickness 4.39 高度Hight 4.40 孔径Bore diameter 4.41 法兰直径Flange diamerer 4.42 方径长度Square neck length 4.43 方径宽度Square neck width 4.44 凸缘高度Collar height 4.45 凸缘直径Collar diameter 4.46 对称度Symmerty 4.47 同轴度Concentricity ( coaxiality ) 4.48 垂直度Perpendicularity 4.49 平行度Parallelism 4.5 直度Straightriess 4.51 槽杆同轴度Recess concentricity 4.52 头杆同轴度Head concentricity5/ 114.53 头杆垂直度Head lnclination2/5---------------------------------------------------------------最新资料推荐------------------------------------------------------ 4.54 斜度Angularity ( taper ) 4.55 弧度或弯曲度Bow or camber 4.56 尾尖角Point angle 4.57 镀锌层厚度Zinc plating thickness 4.58 跳动Run-out 4.59 锥度Taper ratio 4.60 榫长Nib length4.61 榫宽Nib width 4.62 倒角.圆角Chamfer 4.63 平面度Flatness5.机械性能 5.1 抗拉强度Tensile strength 5.2 屈服强度Proof strength 5.3 屈服点Lower yield stress 5.4 扭转强度Torque strength ( torsional strength ) 5.5 剪切强度Shear strength 5.6 冲击韧性Impact strength 5.7 延伸率Elongation 5.8 断面收缩率Reduction 5.9 拉(压)应力Tension 5.10 破坏(扭)力矩Breaking torque 5.11 晶粒度Grahularity 5.12 机械性能Mechanical properties 5.13 脱碳Decarburise 5.14 渗碳Carburization 5.15 最小剩余弹力Minimum residual sping force 5.16 压负荷的百分率Percenatage of compression load 5.17 表面硬度Surface hardness 5.18 芯部硬度Core hardness 5.19 扭矩Torque ( torsion ) 5.20 表面硬化层深度Case harden depth 5.21 氢脆Hydrogen embrittlement 5.22 压载(负)荷Compression load 5.23 硬度试验Hardness test 5.24 头部坚固性试验Head soundness test 5.25 扭转试验Twisting test 5.26 弹性试验Resilience test 5.27 保证载荷试验Proof loading test 5.28 楔负载强度试验Wedge loading test 5.29 弯曲试验Bending test 5.30 旋入试验Screw-in test 5.31 最小破坏力矩试验Torsional test and minimum torques7/ 115.32 永久变形试验Permanent deformation test 5.33 盐雾试验Salt spray test 5.34 弹性Elasticity5.35 韧性Tenacity ( Toughnee ) 5.36 塑性Fiexibility 5.37 磁力碳伤Magnetic particle inspection6.材料-热处理-表面处理 6.1 碳钢Carbon steel 6.2 低碳钢Low carbon steel 6.3 中碳钢Medium carbon steel 6.4 合金钢Alloy steel 6.5 热处理钢Heat-treated steel 6.6 低马钢Low carbon martensite steel 6.7 奥氏体不锈钢Austenitic stainless steel 6.8 马氏体不锈钢Martenitic stainless steel 6.9 铁Iron 6.10 铝Aluminium 6.11 黄铜Brass 6.12 紫铜Copper 6.13 青铜Bronze 6.14 塑料Plastic 6.15 淬火Quenched 6.16 回火Tempered 6.17 退火Annealed 6.18 表面硬化Case hardened 6.19 强度等级Class 6.20 氧化Oxide ( anodizing ) 6.21 金属Metal 6.22 非金属Metalloid 6.23 发黑Black 6.24 本色Plain ( self colour ) 6.25 热处理Heat treatment 6.26 涂层Coating 6.27 表面处理Finish 6.28 涂蜡Waxed 6.29 镀锌(兰白锌) Zinc plated ( zinc / clear ) 6.30 镀黄锌Zinc yellow ( Y.Z.P.)6.31 镀黑锌Zinc plated black 6.32 镀镍Nickel plated 6.33 镀铜Brass plated 6.34 热浸镀锌Hot dip galvanized ( H.D.G.) 6.35 电镀Electplating 6.36 机械镀锌Mechanical galvaizing 6.37 表面热处理Surface heat treatment 7、加工方法7.1 冷镦Cold heading 7.2 冷锻Cold forging 7.3 热锻Hot forging 7.4 成型Forming 7.5 切削(断) Cutting3/5---------------------------------------------------------------最新资料推荐------------------------------------------------------ 7.6 缩径Shrink diameter 7.7 搓(攻)丝Threading 7.8 滚丝Thread rolling 7.9 拔丝Drawing 7.10 酸洗Pickling 7.11 钝化Passirating 7.12 废水处理Waste water treatment 7.13 研磨Grinding 7.14 镦粗Upsetting 7.15 开槽Soltting 7.16 刮削Sharing 7.17 滚花Kunrling 7.18 抛光Polishing 7.19 冲压Punching 7.20 滚动Tumbling 7.21 精整Trimming 7.22 铣削Milled 7.23 挤压Extruding 7.24 钻孔Drilling 7.25 模压Embossing 7.26 沉孔Countersinking 7.27 压印Coining 7.28 扩孔Counterboring 7.29 控削Broaching 7.30 辊光Burnishing 7.31 锻造Forging 7.32 剪切Shear 7.33 焊接Welded 7.34 喷砂Sand blasting 8.表面缺陷 8.1 裂缝Cracks 8.2 淬火裂缝Quench cracks 8.3 锻造裂缝Forging cracks 8.4 锻造爆裂Forging bursts 8.5 剪切爆裂Shear bursts 8.6 条痕Laps 8.7 凹痕Voids 8.8 皱纹Folds ( pits ) ( laps ) 8.9 切痕Tool marks 8.10 损伤Damages 8.11 毛刺Burr 8.12 碎屑Chip 8.13 夹杂Inclusions 8.14 锈皮Sharing 8.15 飞边Flash 8.16 开裂Cracks 8.17 锈、锈斑Rust9.螺纹 9.1 普通螺纹Screw thread 9.2 锥螺纹Taper screws thread 9.3 自攻螺纹(宽牙螺纹) Tapping screws thread ( spaced thread ) 9.4 木螺钉螺纹Wood screws thread 9.5 米制螺纹Metric thread 9.6 ISO 米制螺纹ISO Metric thread 9.7 米制细牙螺纹Metric fine pitch thread 9.8 ISO 米制细牙螺纹ISO Metric fine pitch thread 9.99/ 11寸制螺纹Inch thread 9.10 统一螺纹(ISO寸制) Unified screw thread ( ISO inch ) 9.11 惠氏螺纹Whitworth thread 9.12 管螺纹Pipe thread 9.13 惠氏管螺纹Whitworth pipe thread 9.14 螺旋线Helix 9.15 螺旋面Helical surface 9.16 外螺纹External thread 9.17 内螺纹Inernal thread 9.18 牙侧Flank 9.19 沟槽Groove 9.20 凸起Ridge 9.21 牙顶Crest 9.22 牙底Root 9.23 螺纹牙型Thread profile 9.24 螺纹线Thread 9.25 单线螺纹Single--start--thread 9.26 多线螺纹Multi--start--thread 9.27 右旋螺纹Right--start--thread 9.28 左旋螺纹Left--start--thread 9.29 工作牙侧Pressure ( load ) flank 9.30 非工作牙侧Clearing ( clearance ) flank 9.31 牙底的圆角半径Root radius 9.32 牙型高度Height ( or depth ) of thread 9.33 牙型角Included angle 9.34 牙型半角Flank lead 9.35 中径线Pitch line 9.36 螺纹轴线Axis of thread 9.37 导程Flank lead 9.38 双牙导程Dual flank lead 9.39 螺距Flank pitch 9.40 双牙螺距Dual flank lead 9.41 大径Major diameter 9.42 小径Minor diameter 9.43 中径Pitch diameter4/5---------------------------------------------------------------最新资料推荐------------------------------------------------------ 9.44 9.45 9.46 9.47 9.48 9.49 9.50单一中径Simple pitch diameter 作用中径Virtual pitch diameter 螺纹升角Lead angle 基本牙型Basic profile 伞状螺纹Umbrella thread 粗牙螺纹Coarse thread 细牙螺纹Fine thread5/511/ 11。

非金属嵌件六角锁紧螺母Prevailing torque type hexagon nuts(with non-metallic insert)六角开槽螺母Hexagon slotted nuts六角开槽螺母细牙Hexagon slotted and castle nuts-Fine pitch thread六角螺母Hexagon nuts六角螺母－细牙Hexagon nuts-Fine pitch thread全金属六角锁紧螺母Prevailing torque type all-metal hexagon nuts120度半沉头铆钉120degree oval countersunk rivets120度沉头半空心铆钉120 degree countersunk head semi-tubular rivets120度沉头铆钉120 degree countersunk head rivetsT形槽用螺栓Bolts for T-Slot鞍形弹簧垫圈Curved single coil spring lock washers鞍形弹性垫圈Curved spring washers半圆头带榫螺栓Cup head nib bolts半圆头低方颈螺栓Cup square neck bolts with short neck半圆头方颈螺栓Cup head square neck bolts半圆头铆钉Round head rivets扁平头铆钉Thin head rivets扁圆头半空心铆钉Oval head semi-tubular rivets扁圆头铆钉Flat round head rivets标牌铆钉Rivets for name plate标准型弹簧垫圈Single coil spring lock washers, Normal type波形弹簧垫圈Wave single coil spring lock washers波形弹性垫圈Wave spring washers槽钢用方斜垫圈Square taper washers for slot section槽销Grooved pins侧面带孔圆螺母Round nuts with set pin holes in side沉头半空心铆钉Countersunk head semi-tublar rivets沉头带榫螺栓Flat countersunk nib bolts沉头方颈螺栓Flat countersunk square neck bolts沉头铆钉Countersunk head rivets沉头双榫螺栓Flat countersunk double nib bolts大半圆头带榫螺栓Cup head nib bolts with large head大半圆头方颈螺栓Cup head square neck bolts with large head大扁圆头半空心铆钉Truss head semi-tubuar rivets大扁圆头铆钉Truss head rivets带槽圆螺母Slotted round nuts带孔销Pins with split pin hole带锁圈的螺钉锁紧挡圈Lock rings with screw and circlip单耳止动垫圈Tab washers with log tab弹性圆柱销Spring-type straight pins-Slotted等长双头螺柱Double end studs地脚螺栓Eyelet bolts吊环螺钉Eyebolts蝶形螺母Wing nuts端面带孔圆螺母Round nuts with drilled holes in one face方螺母Square nuts方头凹端紧定螺钉Square set screws with cup point方头长圆柱端紧定螺钉Square set screws with long dog point方头长圆柱球面端紧定螺钉Square set screws with long dog point and rounded end方头倒角端紧定螺钉Square set screws with chamfered end方头短圆柱锥端紧定螺钉Square set screws with short dog point and cone end非金属嵌件六角法兰面锁紧螺母Prevailing torque type hexagon nuts with flange (with non-metallic insert)封闭型扁圆头抽芯铆钉Mushroom head break mandrel closed end blind rivets封闭型沉头抽芯铆钉120 deg flush head break mandrel closed end blind rivets盖形螺母Acorn nuts工字钢用方斜垫圈Square taper washers for I section管状铆钉Pope type rivets滚花薄螺母Knurled nuts滚花高螺母Knurled nut with collar滚花高头螺钉Knurled thumb screws滚花头不脱出螺钉Knurled thumb screws with waisted shank滚花小头螺钉Knurled screws with small head焊接方螺母Square weld nuts焊接六角螺母Hexagon weld nuts环形螺母Lifting nuts活节螺栓Eye bolts机动弧焊用焊接螺柱Weld studs for are welding夹紧挡圈Grip rings开槽半沉头不脱出螺钉Slotted raised countersunk head screws with waisted shank开槽半沉头螺钉Slotted raised countersunk head screws开槽半沉头自攻螺钉Slotted raised countersunk head tapping screws开槽长圆柱端紧定螺钉Slotted set screws with long dog point开槽沉头不脱出螺钉Slotted countersunk head screws with waisted shank开槽沉头螺钉Slotted countersunk head screws开槽沉头自攻螺钉Slotted countersunk head tapping screws开槽盘头螺钉Slotted pan head screws开槽带孔球面圆柱头螺钉Slotted capstan screws开槽盘头螺钉Slotted pan head screws开槽盘头自攻螺钉Slotted pan head tapping screws开槽平端紧定螺钉Slotted set screws with flat point开槽球面大圆柱头螺钉Slotted large raised cheese head screws开槽球面圆柱头轴位螺钉Slotted raised cheese head with shoulder开槽无头轴位螺钉Slotted shoulder screws开槽圆柱端定位螺钉Slotted setscrews with dog point开槽圆柱头螺钉Slotted cheese head screws开槽圆柱头轴位螺钉Slotted cheese head screws with shoulder开槽锥端定位螺钉Slotted setscrews with cone point开口挡圈“E” rings开口垫圈Washers with split开口销Split pins开口型扁圆头抽芯铆钉Mushroom head break mandrel blind rivets开口型沉头抽芯铆钉120 deg flush head break mandrel blind rivets开尾圆锥销Taper pins with split空心铆钉Tubular rivets孔用弹性挡圈Circlips for holes孔用钢丝挡圈Roundwire snap rings for hole扣紧螺母Tight nuts六角法兰面螺母Hexagon nuts with flange六角法兰面自钻自攻螺钉Hexagon flange head self-drilling tapping screws六角头螺栓、弹簧垫圈和平垫圈组合件Hexagon head bolt, single coil spring lock washer and plain washer assemblies六角头螺栓和平垫圈组合件Hexagon head bolt and plain washer assemblies六角头螺栓和外锯齿锁紧垫圈组合件Hexagon head bolt and serrated lock washer external teeth assemblies六角头头部戴槽螺栓Hexagon bolts with slot on head六角头头部带孔螺栓Hexagon blots with wire holes on head六角头自攻螺钉Hexagon head tapping screws六角头自攻螺钉和大垫圈组合件Hexagon head tapping screw and plain washer assemblies六角头自攻锁紧螺钉Hexagon head thread forming screws六角自锁螺母Self-locking nuts, hexagon内齿锁紧垫圈Lock washers internal teeth。

最全紧固件中英文对照，外贸必备词典！一、紧固件Fasteners标准紧固件StandardFasteners非标准紧固件NonstandardFasteners特殊紧固件SpecialFasteners汽车紧固件AutomotiveFasteners铜制紧固件BrassFasteners航天用紧固件AerospaceFasteners精密紧固件PrecisionFasteners化学紧固件ChemicalFasteners摩托车紧固件MotorcycleFasteners不锈钢紧固件StainlessSteelFasteners铁道紧固件RailwayFasteners防松紧固件Self-lockingFasteners高强度紧固件HighstrengthFastenersPEM紧固件PEMFasteners钢结构紧固件SteelStructuralFasteners压铆紧固件Self-ClinchingFasteners铝制紧固件AluminumFasteners钛合金紧固件TitaniumAlloyFasteners尼龙紧固件NylonFasteners精制紧固件FinishedFastener粗制紧固件UnfinishedFastener螺纹紧固件ThreadedFastener半精制紧固件Semi-FinishedFastener抗剪紧固件ShearFastener抗拉紧固件TensionFastener面板紧固件PanelFasteners二、螺栓Bolts六角头螺栓HexagonHeadBolts六角法兰面螺栓HexagonFlangeBolts轨道螺栓（鱼尾螺丝）TrackBolts高强度螺栓HighStrengthBolts地脚螺栓EyeletBolts马车螺栓CarriageBolts护拦螺栓GuardrailBots焊接螺栓WeldBolts双头螺栓DoubleEndBolts钢结构连接副StructuralBolting内六角螺栓HexSocketBolts合金钢螺栓AlloySteelBolts复合材料用螺钉（夹板用）ParticleBoardScrews犁壁螺钉PlowBolts不锈钢木螺丝StainlessSteelWoodScrews套挂螺栓及螺钉ToggleBolts钛合金膨胀螺钉TitaniumAlloyExpansionBolts不锈钢高低牙螺钉StainlessSteelHigh-LowThreadScrews 不锈钢机械螺钉StainlessSteelMachineScrews不锈钢钻尾螺钉StainlessSteelSelfDrillingScrews不锈钢自攻螺钉StainlessSteelSelfTappingScrews不锈钢自削螺钉StainlessSteelThreadCuttingScrews不锈钢三角牙螺钉StainlessSteelTri-LobularThreadScrews 不锈钢宽牙螺钉StainlessSteelCoarseThreadScrews开槽沉头螺钉SlottedFlatCountersunkHeadMachineScrews 开槽盘头螺钉SlottedPanHeadMachineScrews十字槽盘头螺钉CrossRecessedPanHeadMachineScrews 滚花头台阶螺钉KnurledThurmbScrews六角头木螺钉HexagonHeadWoodScrews平头滚花螺钉KnurledThinThumbScrews?四、螺母/螺帽Nuts六角螺母HexagonNuts六角盖形螺母HexCapNuts六角锯齿螺母HexSerratedNuts六角法兰螺母HexFlangeNuts六角平面螺母HexFlatNuts六角厚螺母HexThickNuts重型六角开槽螺母HeavyHexagonSlottedNuts高脚螺母HexCouplingNuts(HighNuts)圆螺母RoundNuts四角螺母/四方螺母SquareNuts四方焊接螺母SquareWeldNuts四爪螺母Four-ClawNuts管用螺母PipeNuts轮壳螺母WheelNuts蝶型螺母WingNutsU形螺母UNutsT形螺母TNuts环首螺母EyeNuts齿形螺母KepNuts齿花螺母ClinchNuts焊接螺帽WeldNuts压铆螺母Self-clinchingNuts高张力螺母HighStrengthNuts建业用螺母StructuralNuts不锈钢螺母StainlessSteelNuts铜螺母BrassNuts铝螺母AluminumNuts合金钢螺母AlloySteelNuts重型车螺母HeavyDutyWheelHubNuts铁器焊接袋帽AcornCapNuts金属预置扭矩式螺母All-MetalPrevailingTorqueTypeNuts壁虎螺母AnchorNuts大尺寸螺母BigSizeNuts铁盖袋帽ClosedEndAcornNuts盘形华司螺母ConicalWasherNuts铁盖+尼龙圈组合盖帽Din986DomedCapNuts法兰尼龙盖帽FlangeNylonInsertLockNuts平面华司螺母FlatWasherNuts六角割沟螺母HexSlottedNuts自锁螺母Self-LockingNuts制止螺母SlidingNutsSLN-自动防松螺母SLNSelf-LockingNuts特殊螺母SpecialNuts弹簧螺母SpringNuts不锈钢法兰螺母StainlessSteelFlangeNuts不锈钢六角轮缘尼龙螺母StainlessSteelFlangeNylonInsertLockNuts 不锈钢六角重型螺母StainlessSteelHeavyHexNuts不锈钢六角螺母StainlessSteelHexNuts不锈钢尼龙嵌入螺母StainlessSteelNylonInsertLockNuts普通六角螺母HexNuts六角重型螺母HeavyHexNuts薄型螺母HexJamNuts尼龙嵌入防松螺母NylonInsertLockNuts尼龙锁紧螺母NylonCageNuts机械螺丝用六角螺母HexMachineScrewNuts米制六角开槽螺母MetricSlottedHexNuts轨道螺栓用方螺母TrackBoltNuts米制六角金属锁紧螺母PrevallingTorqueHexagonNuts开槽螺母SlottedRoundNuts六角开槽薄螺母HexagonSlottedThinNuts?五、螺柱Studs?压铆螺柱Self-ClinchingStuds铜螺柱BrassStuds焊接螺柱WeldStuds双头螺柱DoubleEndStuds六角螺柱HexStuds支撑卡柱Self-ClinchingStandoffs?六、垫圈Washers弹簧垫圈SpringWashers/SpringLockWashers宽型弹簧垫圈Extra-dutyHelicalSpringLockWashers杯型垫圈Cupwashers波形垫圈WaveWashers内齿垫圈InternalToothWashers外齿垫圈ExternalToothWashers铜垫圈CopperWashers方垫圈SquareWashers密封垫圈SealingWashers碟形弹簧垫圈DiscSpringWashers外舌止动垫圈ExternalTabWashers高强度垫圈Highstrengthenwashers橡胶垫圈RubberWashers锁紧垫圈LockWashers平垫圈PlainWashers鞍型弹性垫圈CurvedSpringWashers锯齿锁紧弹性垫圈Toothedlockwashers外锯齿锁紧垫圈SerratedLockWashers锥形垫圈TaperWashers重型弹簧垫圈HeavySpringLockWashers尼龙垫圈NylonWashers淬硬钢垫圈HardenedSteelWashers?七、铆钉Rivets?平头铆钉FlatHeadRivets击芯铆钉DriveRivets彩色铆钉ColoredRivets沉头铆钉CountersunkHeadRivets半沉头铆钉OvalCountersunkHeadRivets平锥头铆钉ConeHeadRivets抽芯铆钉BlindRivets开口铆钉SplitRivets开口型抽芯铆钉OpenEndBlindRivets拉铆钉PopRivets封闭铆钉ClosedEndRivets封闭性抽芯铆钉SealedTypeBlindRivets塑料铆钉PlasticRivets空心铆钉TubularRivets环槽铆钉RingGrooveRivets单鼓型铆钉Single-GripRivets圆头铆钉RoundHeadRivets高沉头铆钉CountersunkHeadRivets铝铆钉AluminumRivets实心铆钉SolidRivets沉头实心铆钉CountersunkHeadSolidRivets灯笼铆钉LanternBlindRivets半空心铆钉Semi-TubularRivets圆头半空心铆钉Semi-tubularPanHeadRivets异型铆钉SpecialRivets不锈钢铆钉StainlessSteelRivets双鼓型铆钉Multi-gripRivets高强度铆钉HighStrengthRivets台阶铆钉StepRivets面板铆钉TabletRivets开花型抽芯铆钉FloweringBlindRivets拉花型抽芯铆钉PeelTypeBlindRivets沟槽型抽芯铆钉GroovedTypeBlindRivet铆接工具RivetingTool?八、壁虎（膨胀螺栓）Anchors/ExpansionBolts化学锚栓ChemicalAnchors打入式壁虎HammerDriveAnchors内迫壁虎DropinAnchors重型壁虎HeavyDutyAnchors锤钉壁虎HitAnchors中空壁虎HollowWallAnchors套管壁虎SleeveAnchors插片壁虎CeilingAnchors门窗、地板专用壁虎NylonFrameAnchorsorMetalframeAnchors电梯壁虎BoltAnchors车修壁虎WedgeAnchors鱼眼壁虎TieWireAnchors外迫壁虎CutAnchors塑料膨胀PlasticAnchors不锈钢重载胀栓HeavyDutyExpansionAnchors象脚壁虎ElephantFootAnchors长型兰花夹ShortStrapAnchors?九、销Pins?开口销SplitPins圆锥销TaperPins锁销LockPins销轴ClevisPinswithhead槽销GroovedPins弹性销SpringPins圆柱销ParallelPins弹性圆柱销SlottedSpringPins带孔销Pinswithsplitpinhole?十、挡圈Circlips/Rings?开口挡圈Erings孔用挡圈Circlipsforholes轴用钢丝挡圈RoundwireSnapRingsforshaft 轴肩挡圈Ringsforshoulder夹紧挡圈GripRings轴用卡簧Circlipsforshafts带齿轴用挡圈RetainingRingswithLugsforshafts 钢丝锁圈RoundwireCirclips锥形锁紧挡圈LockRingswithconepins?十一、其他Others?牙条ThreadedRod冲压件Stampings平键ParallelKeys半圆键WoodruffKeys扳手Spanners钢丝螺套WireThreadInsert自动车床车削件CNCTurningParts齿轮Gears模具Molds线材盘元Ironorsteelwirerod铰链Hinge表面处理SurfaceTreatment。

紧固件-中英文对照.docNo.xx 简写中文1screw scr螺丝2nut nut 螺母3washer wash垫圈4head hd 头5thread thre 螺纹6coating coat 镀层7rivet riv 铆钉8standoff stdoff 内外六角钉9driver driv 穴10hexagon hexa六角11tooth tooth 齿12lock lck 锁13spring spr 弹簧14wave wave 波浪型15pitch pitch 牙距16partial thread PT 半螺纹17PT PT一种螺纹形式18Full Thread FT全螺纹19silver silv 银20cone cone锥形21 Eco-syn Eco 30度牙的一种螺纹22 ThreadForming TF自攻螺纹23 Self Tapping self tapp自切屑螺纹24 pin pin 销25shaft Shaf轴26steel St铁27stainless steel SS不锈钢28Brass(Cu) Bras(Cu)铜29Aluminum AL 铝30Rubber Rub橡胶31machine screw mech scr机制螺丝32SEM screw SEM Scr组合螺丝33Material material 材料34Grade GD等级35Finish Finish表面处理36Point Point 点37Clamp Clam夹子38internal Int 内39external ext 外40thickness /厚度41length /xx42 hole /xx43 Metric Metcric 公制44 DIN /德标45 ANSI /美标46 JIS /日标螺丝相关参数英语对照A:Machine Screw:机械螺丝B:Tapping Screw:自攻螺丝 (分使用于金属与使用于塑料二种 ) B-1: Sheet Metal Tapping Screw. 铁(板牙自攻螺丝 )B-2: Plastic Tapping Screw.塑(料用 ,自攻螺丝 )C:Wooden Screw 木:工螺丝D:Drywall Screw :水泥墙螺丝常见螺丝材质 :a.Low Carbon Steel 低:碳钢b. SS-304 : Stainless Steel 304c.SS-302: Stainless Steel 302结:构韧性较好d.Aluminum 5052 :铝合金 5052d.Brass:xxe.Bronze:青铜f.UNS C11000 Copper:锑铜Finish Code:外观处理规格Head Code:头部外型螺丝型号 Drive Code:头部剖沟 ,特征型号Length Code:螺丝长度(mm)A-1: Thread Code:螺丝型号A-2: Length Code:螺丝长度 :A-3: Drive Code/头部剖沟 ,特征 .a. Slotted:一字 ( Minus )b. Phillips:十字 ( Plus )c.Phil-Slot:一字 / 十字d.Hex Scoket:xxe.One Way:单向 (只可锁入 ,不可退出 ) A-4: Head Code/头部外型 .a. Flat:平头 (锁入后 ,顶部与工作件齐平 )b.Oval:色拉头c.Round:圆头d.Pan:圆扁头e.Truss:大圆扁头f.Hex :六角头A-5: Finish Code/外观处理 .a. Z: Zine-Plated:镀锌b. Ni: Ni-Plated:镀镍c.Tin-Plated:镀锡d.Zine Plated / Green Iridite:镀锌绿膜处理 .e.Radiant Plated:镀五彩f.Passivate:抗氧化处理 .g.Alodial Finish:无外观处理螺纹大径： Major Diam螺纹中径： Pitch diam螺纹底径： Minor diam通止规： Go/No go gage机械性能： mechanical and physical propertiesunified thread 统一英制螺纹Lustrate hydrogen after galvanizing to avoid hydrogen embrittlement 镀后去氢，防止氢脆 Case carburization表面渗碳With across flats 对边With across corners 对角Radius of fillet:头下圆角Transition thread length 过度螺纹Wrenching height 扳拧高度Rockwell 铬氏硬度Vickers 维氏硬度Brinellxx 氏硬度Metallography microscope 金相显微镜Salt spray device盐雾试验箱Tensile testing machine拉力试验机Cold forming 冷打Hot forging 红镦P C 8 = property class 8机械性能 8 级原材料： Raw material 球化退火： Annealing冷拔： Drawingxx：Forming机加工： Machining螺纹成型： Roll Threading热处理： heat-treatment表面处理： finish去氢： Lustrating hydrogen检验： Inspection包装： Packing入库： Stocking车床： lathe磨制： grinding红打： hot forging冲压： punchingDiameter 直径Lengthxx各类紧固件标准件产品xx 对照插片壁虎 Steel Ceiling Anchors内迫壁虎 Drop in Anchors碳钢锤钉壁虎Steel Hit Anchors碳钢六角螺帽Steel Hex Coupling Nuts强力 xx 壁虎 Wedge Anchors外迫壁虎 Cut Anchors化学壁虎 Chemical Anchors不锈钢重载胀栓Heavy Duty Expansion Anchors鱼眼壁虎企眼长螺帽Tie Wire Anchors锌合金打入式壁虎Hammer Drive Anchors弹簧螺帽 Strut Nuts兰花夹系列 T oggle Bolts (Spring Toggle & Gravity Toggle)门窗、地板专用壁虎Nylon Frame Anchors or Metalframe Anchors石膏板中空壁虎Hollow Wall Anchors套管式壁虎 Sleeve Anchors打入式壁虎鱼形尼龙壁虎 Nylon Frame Harmmer Fixing (Nylon Hammer Drive Anchors)强力式锤钉壁虎 Hit Anchors电梯壁虎 Bolt Anchors重载壁虎 Heavy duty anchors两片夹 Loxin Masonry Anchors定位螺栓 Set Bolts长型兰花夹 Short Strap Anchors工具棒 Drop in Setting Tools象脚壁虎 Elephant foot anchors水泥预埋件 Concrete Insert翻边胀轴 Drop in Anchor with Lip冲件 Legs Drywall Anchors六角盖头螺帽Hex Cap Nuts六角锯齿螺帽Hex Serrated Nuts六角轮缘螺帽Hex Flange Nuts高脚螺帽 Hex Coupling Nuts(High Nuts) 圆螺帽 Round Nuts 四角螺帽 Square Nuts管用螺帽 Pipe Nuts轮壳螺帽 Wheel Nuts蝶型螺帽 Wing NutsU 形螺帽 U NutsT 形螺帽 T Nuts环首螺帽 Eye Nuts齿形螺帽 Kep Nuts齿花螺帽 Clinch Nuts耐候钢六角重型螺帽Corten Steel Heavy Hex Nuts焊接螺帽 Weld Nuts高张力螺帽 Heigh Strength Nuts建业用螺帽 Structural Nuts不锈钢螺帽 Stainless Steel Nuts铜螺帽 Brass Nuts铝螺帽 Aluminum Nuts合金钢螺帽 Alloy Steel Nuts重型车螺帽 Heavy Duty Wheel Hub Nuts铁器焊接袋帽Acorn Cap Nuts金属预置扭矩式螺帽All-Metal Prevailing Torque Type Nuts 壁虎螺帽 Anchor Nuts大尺寸螺帽 Big Size Nuts铁盖袋帽 Closed End Acorn Nuts盘形华司螺帽Conical Washer Nuts铁盖 +尼龙圈组合盖帽Din 986 Domed Cap Nuts突缘尼龙盖帽Flange Nylon Insert Lock Nuts平面华司螺帽Flat Waser Nuts六角割沟螺帽Hex Slotted Nut自锁螺帽 Self-Locking Nuts制止螺帽 Sliding NutsSln-自动防松螺帽 Sln Self-Locking Nuts其它特殊螺帽Special Nuts弹簧螺帽 Spring Nuts不锈钢突缘螺帽Stainless Steel Flange Nuts不锈钢六角轮缘尼龙螺帽Stainless Steel Flange Nylon Insert Lock Nuts 不锈钢六角重型螺帽Stainless Steel Heavy Hex Nuts 不锈钢六角螺帽Stainless Steel Hex Nuts不锈钢尼龙嵌入螺帽Stainless Steel Nylon Insert Lock Nuts普通六角螺帽Hex Nuts六角重型螺帽Heavy Hex Nuts薄型螺帽 Hex Jam Nuts尼龙嵌入防松螺帽Nylon Insert Lock Nuts机械螺丝用六角螺帽Hex Machine Screw Nut六角螺丝 (栓) Hex Head Cap Screws(Hex Bolts)六角机械螺丝Hex Head Machine Bolts六角 xx 螺丝 Hex Lag Bolts四角螺丝 Square Head BoltsT 头螺丝 T Head Bolts环首螺丝 Eye Bolts内六角孔螺丝Hex Socket Cap Screws 固定螺丝 Set Screws螺椿栓 Stud Bolts螺旋椿 Screw Studs轮壳螺栓 Wheel Bolts翼形螺丝 Wing Screws自攻螺丝 Self Tapping Screws自削螺丝 Thread Cutting Screws钻尾螺丝 Self Drilling Screws旋入螺丝 Drive Screws机械螺丝 Machine Screws木螺丝 Wood Screws家具螺丝 Furniture Screws塑板螺丝 Chipboard Screws墙用螺丝 Drywall Screws基础螺栓 Foundation BoltsU 型螺栓 U Bolts勾头螺栓 Hook Bolts套挂螺丝 Toggle Bolts轨道螺栓 (鱼尾螺丝 ) Track Bolts耐候钢螺丝 Corten Steel Heavy Hex Bolts扭矩控制螺栓T.C.Bolts高张力螺栓 High Strength Bolts剪力钉 (焊接螺丝 ) Welding Studs螺丝附华司组合Screws And Washers Assembled(Sems) 大尺寸螺栓 Big Size Bolts不锈钢小螺丝Stainless Steel Sheet Metal Screws不锈钢大螺丝Stainless Steel Bolts铜螺丝 Brass Screws铝螺丝 Aluminum Screws合金钢螺丝 Alloy Steel Screws电子螺丝 Electronic Screws微小精密螺丝Micro Screws塑料螺丝 Plastic Screws复合材料用螺丝Particle Board Screws钛合金螺丝 Titanium Alloy Bolts钛、锆、钼、铌等螺丝、零件、材料Ti,Zr,Mo,Nb Pare Metal Bolts Parts 拇指螺丝 Thumb Screws双头牙螺丝 Double End Screws Hanger Bolt车辆 (汽车 )螺丝、螺帽 Automotive Fasteners航天用螺丝 Aerospace Fasteners飞机特殊扣件Source Control BoltsxxBlind Bolts面板螺丝 Panel Fasteners电梯螺丝 Elevator Bolts四角头固定螺丝Square Set Screws大头马车螺丝Step Bolts单向螺丝 One Way Lag Screws管夹螺丝 Hose Clamp Screws不锈钢固定螺丝Stainless Steel Hex Socket Cap Screws 不锈钢内六角螺丝Stainless Steel Hex Socket Cap Screws 铰链螺丝 Hinge Screws货柜螺丝 Container Screws复合材料钻尾螺丝Bi-Metal Self Drilling Screws三角牙螺丝 Trilobular Thread Screws高低牙螺丝 High Low Screws夹板用螺丝 Particle Board Screws马桶螺丝 Toilet Closet Bolts特长螺丝 Special Longer Screws建业螺丝 Building Fasteners不锈钢六角螺丝Stainless Steel Hex Socket Cap Screws 其它特殊螺丝Special Screws Or Bolts不锈钢特殊螺丝Special Stainless Steel Screws宽牙螺丝（粗牙螺丝）Coarse Thread Screws链带螺丝 Collated Screws水泥螺丝 Concrete Screws板模螺丝 Construction Bolts锌蝶螺丝 Die Cast Wing Screws; Zinc Alloy重型车螺丝 Heavy Duty Wheel Hub Bolts内六角固定螺丝Hex Socket Set Screws复合材料用螺丝（夹板用）Particle Board Screws 犁壁螺丝 Plow Bolts不锈钢木螺丝Stainless Steel Wood Screws套挂螺栓及螺丝T oggle Bolts钛合金膨胀螺丝Titanium Alloy Expansion Bolts 六角盖头螺帽Hex Cap Nuts六角锯齿螺帽Hex Serrated Nuts六角轮缘螺帽Hex Flange Nuts高脚螺帽 Hex Coupling Nuts(High Nuts)圆螺帽 Round Nuts四角螺帽 Square Nuts管用螺帽 Pipe Nuts轮壳螺帽 Wheel Nuts蝶型螺帽 Wing NutsU 形螺帽 U NutsT 形螺帽 T Nuts环首螺帽 Eye Nuts齿形螺帽 Kep Nuts齿花螺帽 Clinch Nuts耐候钢六角重型螺帽Corten Steel Heavy Hex Nuts 焊接螺帽 Weld Nuts高张力螺帽 Heigh Strength Nuts建业用螺帽 Structural Nuts不锈钢螺帽 Stainless Steel Nuts铜螺帽 Brass Nuts铝螺帽 Aluminum Nuts合金钢螺帽 Alloy Steel Nuts重型车螺帽 Heavy Duty Wheel Hub Nuts铁器焊接袋帽Acorn Cap Nuts金属预置扭矩式螺帽All-Metal Prevailing Torque Type Nuts 壁虎螺帽 Anchor Nuts大尺寸螺帽 Big Size Nuts铁盖袋帽 Closed End Acorn Nuts盘形华司螺帽Conical Washer Nuts铁盖 +尼龙圈组合盖帽Din 986 Domed Cap Nuts突缘尼龙盖帽Flange Nylon Insert Lock Nuts平面华司螺帽Flat Waser Nuts六角割沟螺帽Hex Slotted Nut自锁螺帽 Self-Locking Nuts制止螺帽 Sliding NutsSln-自动防松螺帽 Sln Self-Locking Nuts其它特殊螺帽Special Nuts弹簧螺帽 Spring Nuts不锈钢突缘螺帽Stainless Steel Flange Nuts不锈钢六角轮缘尼龙螺帽Stainless Steel Flange Nylon Insert Lock Nuts 不锈钢六角重型螺帽Stainless Steel Heavy Hex Nuts 不锈钢六角螺帽Stainless Steel Hex Nuts不锈钢尼龙嵌入螺帽Stainless Steel Nylon Insert Lock Nuts锌压属螺帽 Zinc Die Casting Nuts普通六角螺帽Hex Nuts六角重型螺帽Heavy Hex Nuts薄型螺帽 Hex Jam Nuts尼龙嵌入防松螺帽Nylon Insert Lock Nuts机械螺丝用六角螺帽Hex Machine Screw Nut合金钢线材盘元Alloy Steel Wire Rod球状化线材 Annealing Wire And Rod黑铁丝 Black Wire黄铜棒线 Brass Wire And Rod磨光棒钢 Bright Steel Bar(Hex/Round/Square)铜合金线 Copper Alloy Wire线切割线 E.D.M Cutting Wire快削钢线材盘元Free Cutting Steel Wire Rod线材 Iron Or Steel Wire线材盘元 Iron Or Steel Wire Rod洋白铜线 Nickel Silver Wire磷青铜线 Phosphate Bronze Wire不锈钢条棒 Stainless Steel Bar(Round/Hex/Square)不锈钢冷锻线材Stainless Steel Cold Heading Wire不锈钢线 (抽线后 ) Stainless Steel Draw Wire不锈钢线材 Stainless Steel Wire不锈钢线材及盘元Stainless Steel Wire And Rod棒钢 Steel Bar(Hex/Round/Square)转回 90 度碾线头机 90 讧 evolving Wire Twisting Machine 气动拉钉机 Air Riveter各式螺丝类产品自动包装Automatic Packaging For All Kinds Of Packaging 自动包装机 Automatic Packing Machine螺丝制造搓牙机械Automatic Thread Rolling Machine螺丝割尾加工机械Automatic Thread Slotting Machine螺丝制造成型机械Automatic Trimming Machine拉钉打头机 Blind Rivet Heading Machine螺丝、螺帽成型机Bolt Formers,Nuts Formers,Headers螺丝、螺帽热处理Bolt Nut And Screws Heat Treatment螺丝、螺帽热处理炉Bolt Nut And Screws Heat Treatment Furnaces球状化电器炖炉Carburizing Furnace Vacuum And Bell Type Furnace超防锈复合瓷膜Ceramic Coating连续式光辉渗碳淬火炉Continuous Bright Carburizing Quenching Furnace 连续式光辉调质淬火炉Continuous Bright Hardening Quenching Furnace 中、高热镀锌光辉连续炉Continuous Bright Heat Treat Furnace连续式光辉热处理炉Continuous Type Bright Heat Treatment Furnace螺丝割尾及特殊割遘加工Machine Screw Shank Slotting螺丝钻孔加工Screw Shank Drilling鸡眼上下模 Eyelets Dies一般线材、盘元、退火炉General Wire,Wire Rod,Annealing Furnace倒立式滑落型伸线机Handstand Type Wire Drawing Machine 十字冲模 Header Punches In Various Drives成型冲模 Header Punches In Various Drives螺丝打头机 Heading Machine螺丝制造高速搓牙机械High Speed Automatic Thread Rolling Machine高中低周波感应加热炉High,Medium,Low Frequency Induction Heater空心打头机 Hollow Heading Machine热浸镀锌螺丝、螺帽Hot Dip Galvanizing Bolts And Nuts机械镀锌 Mechanical Galvanized迷你成型机 Mini-Formers成品自动收线机Non-Stop Coiler精抽自动收线机Non-Stop Coiler(Skinpass)螺帽模 Nut Forming Dies螺帽成型模 Nuts Formers特殊零件成型机Parts Forming Maching冲模 Punch Dies冲子 Punch Pins罗拉成型机 Rollers Formers机(踏)车用螺丝成型机Screw For Motorcycle Or Bicycle Heading Machine 止付螺丝成型机Set Screws Formers 套高成型机 Sockets Formers一般线材、盘元、螺丝合金炖炉Spheroidizing Bright Annealing Furnace 球状化热处理炉Spheroidizing Heat Treatment Furnace。

Description in Chinese 英文品名Desciption in English圆锥销Taper pins圆柱销Parallel pins开槽圆柱头螺钉Slotted cheese head screws开槽盘头螺钉Slotted pan head screws单耳止动垫圈Tab washers开口销Split cooter pins开槽半沉头木螺钉Slotted raised csk head wood screws 开槽半圆头木螺钉Slotted round head wood screws开槽沉头木螺钉Slotted countersunk head wood screws 平垫Plain washers平垫（带倒角）Mediun washers平垫Plain washers重型弹垫Spring lock washers,tang ends标准弹垫Spring lock washers,square ends鞍形弹垫Single coil spring lock washers弹簧止动垫圈Curved spring washers波形弹垫Wave spring washersT型方颈螺栓T-head blots with square neckT型双接头螺栓T-head bolts with double nip螺纹圆锥销Taper pins with threaded endT型头螺栓T-head bolts蝶型螺母（美制）Wing nuts America form蝶型螺母（德制）Wing nuts germany form蝶型螺母（美制）Wing screws America form蝶型螺母（德制）Wing screws germany form圆球型盖型螺母Ball knobs开槽带孔球面圆柱头蚴钉Slotted capstan screws开槽长圆柱端紧定螺钉Slotted set srews with full dog point开槽平端紧定螺钉（半牙）Slotted set srews with chamfered end 小六角特薄细牙螺母Pip nuts with thread外舌止动垫圈External tap小垫圈(用于圆柱头螺钉) Washers for cheese head screws方斜垫圈（U型）Square taper washers forU-section方斜垫圈（I型）Square taper washers forI-sections方垫圈Square washers开槽凹端紧定螺钉Slotted set with cup point六角薄螺母Hexagon thin nuts细牙六角薄螺母Hexagon thin nuts木螺钉专用垫圈Rounds washers for wood constructions密封帽Sealing caps,push-in type活节螺栓B型Eye bolts form B内舌止动垫圈Internal tab washers双耳止动垫圈Washers with two taps滚花高头螺钉Knurled thumb screws with collar开槽滚花高头螺钉Slotted knurled thumb screws with collar 滚花高螺母Knurled thumb nuts with collar滚花薄螺母Knurled thumb thin nuts锁紧垫圈Sealing washers轴用弹性垫圈Retaining rings for shafts(external),circlips孔用弹性垫圈Retaining rings for bores(internal),circlips方头带垫螺栓Square head bolts with collar方头圆柱底端螺栓Square head bolts with half dog point方头带垫关圆底端螺栓Square head bolts with collar,half dog pointT型槽螺母T-slot nuts单头螺柱Single end studs地脚螺栓Masonry bolts带槽圆螺母Slotted round nuts端面带孔圆螺母Round nuts with drilled holes in one face 开槽平端紧定螺钉Slotted set screws with flat point开槽锥端紧定螺钉Slotted set screws with cone point六角螺母Hexagon nuts方螺母-C Square nuts六角头螺钉Hexagon screws六角头圆柱端紧定螺钉Hexagon set screws with full dog point薄型方螺母-B Square nuts without bevel(pressed nuts)六角头木螺钉Hexgon head wood screw(coach screws)吊环螺钉Lifting eye bolts吊环螺母Lifting eye nuts圆锥型槽销Grooved pins,taper grooved圆锥型槽销（半槽）Grooved pins,taper grooved half length平行槽销（带倒角）Grooved pins,parallel grooved full length前端凹槽槽销Grooved pins,reverve grooved half length中部凹槽槽销Grooved pins,center grooved圆头槽销Grooved pins with round head沉头槽销Grooved pins with countersunk head六角螺母棒Turnuckles(center parts),made out of hexagon bar花蓝螺栓Turnuckles with eye bolt and hook bolt弹性圆柱销Spring pins,heavy type组合式盖型螺母Hexagon domed cap nuts开槽圆螺母(配合沟头扳手) Slotted round nuts for hook spammer圆螺母（带插销孔）Round nuts with set holes盘型弹簧垫圈Disc springs喉箍Hose clamps润滑油嘴（旋扭头）Lubricating nipples,button head管夹Shackles for conduiltsU型螺栓Stirrup bolts(U-bolts)球面垫圈Spherical washers,conical seats圆柱销Parallel pins厚六角螺母Hexagon nuts,1.5d厚六角法兰面螺母Hexagon nuts,1.5d with collar长六角螺母Hexagon nuts,3d外齿锁紧垫圈External teeth lock washers内齿锁紧垫圈Internal teeth lock washers外锯齿锁紧垫圈External teeth serrated lock washers内锯齿锁紧垫圈Internal teeth serrated lock washers开口挡圈Retaining rings for shafts(E-rings),circlips平键（A型）Parallel keys(form A)半圆键Woodruff keys嵌环（支撑环）Thimbles机器螺钉和垫圈组合件Screws and washers assemblies自攻螺钉和垫圈组合件Tapping screws and washer assemblies薄型带孔内六角圆柱螺钉Hexagon cocket head cap screws with hole,low head大六角头螺栓Hexagon head bolts with large head(friction grip nolts)大六角螺母Hexagon nuts with large wideth across flat(friction grip nuts)大垫圈Round washers for friction grip bolts楔型方垫圈Spuare taper washers for friction grip bolts on T-六角法兰面螺母Hexagon flange nuts全金属六角锁紧螺母（2型）Prevailing torque type hexagon nuts,all metallic nuts 轻型弹性圆柱销Spring pins,light type重型弹性圆柱销用垫圈Washers for bolts with heavy type spring pinssISO公制螺纹螺钉（多种头型）Thread forming screws for ISO-metric thread 自攻自钻螺钉（多种头型）Self-drilling tapping screws开槽切削螺纹螺钉（多种头型）Thread cutting screws十字槽切削螺纹螺钉（多种头型）Thread cutting screws cross recessT型四爪螺母Tee nuts with pronge钢结构用六角头螺栓连接副Hexagon head fitted bolts for steel structures开槽盘头自攻螺钉Pan head tapping screws with slot开槽沉头自攻螺钉countersunk flat head tapping screws with slot开槽半沉头自攻螺钉Raised sountersunk oval head tapping screws with slot六角头自攻螺钉Hexagon tapping screws圆柱头螺钉用弹簧垫圈Spring lock washers for screws with cylindrical heads十字槽盘头自攻螺攻Pan head tapping screws with cross recessed十字槽沉头自攻螺攻Countersunk flat head tapping screws with cross recessed十字槽半沉头自攻螺攻Raised countersunk oval head tapping screws with cross薄型内六角圆柱头螺钉Hexagon socket head cap screws with,reduced head十字槽盘头螺钉Pan head screws with cross recessed钢结构用垫圈Washers for steel structures钢结构用六角头螺栓Hexagon head bolts for steel structures内六角沉头螺钉Hexagon socket coutersunk head screws轴用钢丝挡圈Roundwire snap rings for shafts十字槽半沉头木螺钉Cross recessed raised countersunk head wood screws十字槽圆头木螺钉Cross recessed round head wood screws十字槽沉头木螺钉Cross recessed countersunk head wood screws螺纹护套(普通、自锁等) Ciol inserts,coarse,fine thread,silf locking大外径垫圈Washers,outside diameter appro.3d弹簧卡子sping cotter for a bolt平板螺栓Belting bolts(elevator bolts)干壁钉（墙板钉）Dry wall screws环型螺母Lifting nuts(eye nuts)圆螺母用止退垫圈Tab washer for slotted round nuts。

英文英文简写中文头部形状(Head style)Pan Head Pan HD 盘头Flat Head Flat HD 平头或countersunk Head CS HD 沉头Round Head RD HD圆头Oval Head OL HD半沉头Pan washer Head Pan wash HD垫圈盘头Socket Hd Skt HD六角圆柱头Hexagon cap Head Hex Cap HD外六角头Square shouder Head SQ SDR HD方肩头Cheese Head Ches HD圆锥头Wing Head Wing HD带翼头穴型状(Driver style)Philips cross recessed Phil十字Pozidriv cross recessed Pozi米字Torx Torx内梅花6-lobular6-lobuSocket Skt内六角Slot Slt一字槽示意图紧固件专用词中英文对照表面处理(Coating)Znic blue ZB兰锌Zinc black ZBK黑锌Zinc yellow(Zinc Oliver)ZY (ZO)/ZC黄锌/五彩锌Zinc white/Zinc Clear ZW/ZI白锌Black Anodize BL氧化黑色Natural Anodize NA氧化黑色Gold Anodize GD氧化金色Copper Red RU镀红铜Copper Yellow YU镀黄铜Nickel Over Copper CN镀铜底镍Tin Matt DT镀哑锡Flash Black Painting Coating PC镀哑锡Sn/Pb Plating TP镀锡铅合金Sandblast and Anodize SA喷沙阳极Nickel Flash NI镀亮镍Nickel Electroless EN无电解镍Chrome Flash CR镀亮铬Tin Flash ET镀亮锡Gold Plating AU镀金Titanium Plating TI镀钛Cadmium Plating CD镀镉Zinc-Iron Alloy ZF镀镉Chromate CH铬酸盐Electro Painting EF电泳漆Silver Plating Sil Plat/SLVR-PLT/AG镀银Nickel Plating Nic Plat镀镍Black Oxide BO黑氧化Dacromet Dacr达克罗Heat dip zinc HDZinc热浸锌通用缩写Socket Head Cap Screw Scr Cap Skt HD圆柱头内六角螺钉（Universal Abbrev）Passivation PSVT/PS钝化Hexagonal Socket Hex Skt内六角With locking Element W/LKG LMNT自锁/耐落Stainless Steel SST不锈钢大致形状(Rough Style)Split Lock Washer WSHR LKG SPLIT锁紧垫圈Wave Washer WSHR WAVE波形垫圈Flat Washer WSHR FLAT平垫圈Pan Head Machine Screw SCR MACH PAN HD盘头机器螺钉Phillips Screw PHIL SCR十字槽头螺钉Socket Set Screw S.S.S止付螺丝Full Hexagonal Nut NUT HEX FULL 六角全高螺母Hexagonal Jam Nut NUT HEX JAM锁紧螺母Socket Head Cap Screw S.H.C.S内六角圆柱头螺钉Hex Head Cap Screw H.H.C.S外六角螺栓NUT KEPS KEPS NUT K型螺母Hexagon Head Bolt BOLT HEX HD 六角标准螺栓(全螺纹半螺纹视情况而定)。