当前位置：文档之家 › HSU250-T050KK中文资料

HSU250-T050KK中文资料

  • 格式：pdf
  • 大小：352.44 KB
  • 文档页数：4

DUAL SELECTABLE AC INPUT AC-DC 19" COMPATIBLE DOUBLE EUROCARD MULTIPLE OUTPUT 250-360 WATTS SWITCHING MODE POWER SUPPLIES HSU250, HSU300 & HSU360 SERIESFEATURES:DUAL INPUT RANGE USER SELECTABLE DOUBLE OR TRIPLE CONVERTERARCHITECTURE19" COMPATIBLE EUROCARD FORMAT MEET THE SAFETY STANDARDSEMI MEET CISPR PUB. 22 & FCC CLASS A CE MARKING COMPLIANCE6U X 12HP X 160MM DOUBLE EUROCARDVMEbus STANDARDGENERAL SPECIFICATIONEfficiency: Typ. 75-80.0%. Switching Frequency: Typ. 100K Hz. Circuit Topology: Forward circuit. HSU250/HSU300/HSU360 triple converter. HSU360T dual converter architecture. Transient Response: Typ. 3mS following a 25% load change.Power Density: 1.58 Watts / Cubic Inch for HSU250. 1.90 Watts / Cubic Inch for HSU300. 2.28 Watts / Cubic Inch for HSU360 & HSU360T.Operating Temperature: 0 to +50°C at full load. Derates linearly to +70°C at half load. Storage Temperature: -20 to +85°C.Temperature Coefficient: Typ. 0.04%/°C. Cooling: At least 60cfm forced air flow is requiredfor full load. Construction format: 12HP(TE)x6Ux160mm19” compatible double Eurocard VMEbus standard.Safety Standard: IEC950/UL1950 Class I.Note: All measurements are at nominal input, full load, and +25°C unless otherwise specified.OUTPUT SPECIFICATIONOutput Voltage: See Ratings Chart. Output Current: See Ratings Chart.Output Wattage: Typ. 250 Watts for HSU250.Typ. 300 Watts for HSU300.Typ. 360 Watts for HSU360/HSU360T.Output Connector: DIN 41612 at rear. Line Regulation: Typ. 0.4%.Load Regulation: VO1 typ. ±1.0%(Main).VO2 typ. ±1.0%(Main). VO3 typ. ±1.0%(Main).or typ. ±3.0%(PR) for HSU360T.Noise & Ripple: Typ. 1% peak to peak.OVP: Built-in at main VO1/VO2/VO3 (Latch).Adjustability: Available at main output VO1,VO2,VO3. Remote Sense: Installed at main VO1.Overload Protection (OLP): Fully protected againstoutput overload and short circuit.Consult factory for OLP setting.SPECIFICATIONINPUT SPECIFICATIONInput Voltage: 115Vac/230Vac dual selectable.Input Connector: DIN 41612 for HSU250/300/360T.IEC320 AC receptacle for HSU360.Input Frequency: 47-63HzInrush Current: Typ. 65A @230Vac.Input Current: HSU250 6.0A@115Vac/3.0A@230Vac.HSU300 1.2A@115Vac/0.7A@230Vac. HSU360 6.5A@115Vac/3.5A@230Vac. HSU360T 6.2A@115Vac/3.0A@230Vac.Dielectric Withstand: Meet IEC950.EMI: Meet CISPR PUB. 22 & FCC Class A. Power Fail/OK: Option.Remote (Logic) Inhibit: Available. Hold-up Time: Typ. 20mS.Earth leakage: Typ. 0.3mA @230Vac.Over Temperature Protection (OTP): Option.HSU250 SeriesTRIPLE OUTPUTMAIN VO1 @# MAINVO2@ MAIN VO3 @ MODEL NO.Typ. Volt. Max. Typ. Volt. Max. Typ. Volt. Max.HSU250-T050II (HSU250-32) 25.0A 5.0V 30A5.0A12.0V10A 5.0A 12.0V 10AHSU250-T050KK 25.0A 5.0V 30A4.0A15.0V 8A 4.0A 15.0V 8AHSU250-T050MI 25.0A 5.0V 30A2.5A24.0V 5A 5.0A 12.0V 10AHSU250-T033II 35.0A 3.3V 40A5.0A12.0V10A 5.0A 12.0V 10AHSU250-T033EI 35.0A 3.3V 40A 12.0A 5.0V20A 5.0A 12.0V 10AHSU250-T050DI 25.0A 5.0V 30A 15.0A 3.3V20A 5.0A 12.0V 10ASymbol: " " OVP built-in. "@" Adjustable. "#" Remote sensing.MECHANICAL DIMENSIONS:MM [INCHES]WEIGHT: HSU250 2.54kg (5.60 lb.)INPUT & OUTPUT CONNECTORS PIN ASSIGNMENTSAC INPUT TRIPLE OUTPUT ASSORTED SIGNALASSIGNMENT AC-L AC-N AC-G+VO1 +VO2-VO3DC COM NC S(+) S(-) SYSResetACFailHSU250-T P1-28 P1-30 P1-32P2-4,6,8,10,12 P2-28,30P2-16P2-18,20,2224,26P1-8,10,12,24,16,1820,22,24,26P2-14 P2-32 P1-6 P1-4HSU300 SeriesTRIPLE OUTPUTMAIN VO1 @# MAINVO2@ MAIN VO3 @ MODEL NO.Typ. Volt. Max. Typ. Volt. Max. Typ. Volt. Max.HSU300-T050II (HSU300-32) 36.0A 5.0V 40A6.0A12.0V12A 6.0A 12.0V 12AHSU300-T050KK 36.0A 5.0V 40A5.0A15.0V10A 5.0A 15.0V 10AHSU300-T050MI 36.0A 5.0V 40A3.0A24.0V 6A 6.0A 12.0V 12AHSU300-T033II 50.0A 3.3V 55A6.0A12.0V12A 6.0A 12.0V 12AHSU300-T033EI 50.0A 3.3V 55A 15.0A 5.0V-- 6.0A 12.0V 12AHSU300-T050DI 36.0A 5.0V 40A 18.0A 3.3V-- 6.0A 12.0V 12ASymbol: " " OVP built-in. "@" Adjustable. "#" Remote sensing.MECHANICAL DIMENSIONS:MM [INCHES]WEIGHT: HSU300 2.75kg (6.06 lb.)INPUT & OUTPUT CONNECTORS PIN ASSIGNMENTSAC INPUT TRIPLE OUTPUT ASSORTED SIGNALASSIGNMENT AC-L AC-N AC-G +VO1 +VO2-VO3DC COM NC S(+) S(-) SYSResetACFailHSU300-T P1-28 P1-30 P1-32 P2-4,6,8,10,12 P2-28,30P2-16P2-18,20,2224,26P1-8,10,12,24,16,1820,22,24,26P2-14 P2-32 P1-6 P1-4HSU360 SeriesTRIPLE OUTPUTMAIN VO1 @# MAINVO2@ MAINVO3@ MODEL NO.Typ. Volt. Max. Typ. Volt. Max. Typ. Volt. Max.HSU360-T050II42.0A 5.0V 45A6.0A12.0V12A 6.0A 12.0V 12AHSU360-T050KK 42.0A 5.0V 45A5.0A15.0V10A 5.0A 15.0V 10AHSU360-T050MI 42.0A 5.0V 45A3.0A24.0V 6A 6.0A 12.0V 12AHSU360-T033II 55.0A 3.3V 60A6.0A12.0V12A 6.0A 12.0V 12AHSU360-T033EI 55.0A 3.3V 60A 15.0A 5.0V-- 6.0A 12.0V 12AHSU360-T050DI 42.0A 5.0V 45A 18.0A 3.3V-- 6.0A 12.0V 12AHSU360T SeriesTRIPLE OUTPUTMAIN VO1 @# MAINVO2@ MAINVO3●MODEL NO.Typ. Volt. Max. Typ. Volt. Max. Typ. Volt. Max.HSU360T-T050II(HSU360T-32)60.0A 5.0V 70A 2.5A12.0V 3.5A 2.0A 12.0V 3.0AHSU360T-T050KK 60.0A 5.0V 70A 2.0A15.0V 3.0A 2.0A 15.0V 3.0AHSU360T-T050MI 60.0A 5.0V 70A 1.25A24.0V 2.5A 2.0A 12.0V 3.0AHSU360T-T033II 65.0A 3.3V 75A 2.5A12.0V 3.5A 2.0A 12.0V 3.0AHSU360T-T033EI 65.0A 3.3V 75A 6.0A 5.0V-- 2.0A 12.0V 3.0AHSU360T-T050DI 60.0A 5.0V 70A 8.0A 3.3V-- 3.0A 12.0V 8.0A MECHANICAL DIMENSIONS: MM [INCHES]WEIGHT: HSU360&T 2.80kg (6.17 lb.)INPUT & OUTPUT CONNECTORS PIN ASSIGNMENTSAC INPUT TRIPLE OUTPUT ASSORTED SIGNALASSIGNMENT AC-L AC-N AC-G +VO1 +VO2-VO3 DC COM NC S(+) S(-) SYSResetACFailHSU360-T L N G P2-4,6,8,10,12P2-28,30P2-14,16P2-20,2224,26,32P2-18 P2-12 -- -- --HSU360T-T P1-28 P1-30 P1-32 P2-4,6,8,10,12 P2-28,30P2-16 P2-18,20,2224,26 P1-8,10,12,24,1618,20,22,24,26P2-14 P2-32 P1-6 P1-4。

合集下载

APT250 APT500 APT1000 操作说明书

APT250 APT500 APT1000 操作说明书

操作说明书自动端子拉力试验机APT250/APT500/APT1000Ver1.12016年05月11日目次1各部分名称 (2)2标准附件 (4)3操作端子夹具 (5)4操作电线夹具 (6)5开始拉力测试 (7)6其他操作键 (8)7使用软件 (9)8显示错误及常见问题 (13)9I／O (14)10规格 (14)11保固・售后服务 (15)1 各部分名称＜背面＞电线夹具 串行接口 RS232CI/O 界面D-Sub15接头电源开关 拉伸速度调整旋钮 操作开关端子夹具速度调整旋钮和拉伸速度単位：mm/min打开电源时注意在打开主机电源时传感器自动进行调零。

在打开主机电源时请确认在端子一侧的夹具没有受力的情况下才能打开电源。

拉力速度调整旋钮拉下图是拉伸速度调整旋钮请使用小型一字螺丝刀等进行调整。

MIN MAX2标准附件<<配件3操作端子夹具端子夹具杠杆往图示箭头方向推的话，端子夹具就会开口（最大开口宽8mm）。

注意！端子夹具装有弹簧机构，手离开杠杆后夹具就会自动关闭，小心手别被夹具夹住。

把端子放入卡口内后，松开端子夹具杠杆，端子就自动被牢牢夹住。

夹具（右）夹具（左）端子夹具杠杆夹具4 操作电线夹具按「START 」后电线夹具开始后退，夹具滚轮自动关闭。

电线破断停止后，按「ENTER 」夹具返回原点。

返回原点时，夹具滚轮自动打开，放下电线。

电线夹具可夹住0.13sq(AWG26)～5sq(AWG10)电线。

5开始拉力测试1.确认电线夹具在原点位置。

2.打开端子开关杠杆，将端子装入端子夹具。

3.按下控制面板上的「START」按键。

电线夹具自动后退，夹着电线开始拉力测试。

这时在控制面板的LCD上实时显示拉力的数值。

一旦检知到电线和端子断开时，自动停止。

同时，同时在控制面板的LCD上显示刚好断开前的拉力测试值。

※直到按「ENTER」或「START」按键，LCD显示顶峰值。

按下「ENTER」按键时：背面RS232C连接到计算机的情况下，顶峰值传送到计算机软件。

HSU100Q-050MII中文资料

HSU100Q-050MII中文资料

DUAL SELECTABLE AC INPUT AC-DC SINGLE & MULTIPLE OUTPUT45-150 WATTS 19" COMPATIBLE EUROCARD SWITCHING POWER SUPPLIES HSU45,HSU60 & HSU100 SERIESFEATURES:DUAL INPUT RANGE USER SELECTABLE 19" COMPATIBLE EUROCARD FORMAT MEET THE SAFETY STANDARDSEMI MEET CISPR PUB.22 & FCC CLASS B CE MARKING COMPLIANCEHSU45 6TE x 3U x 160MM VMEbus STANDARDHSU60 8TE x 3U x 160MM VMEbus STANDARD HSU100 10TE x 3U x 160MM VMEbus STANDARDSPECIFICATIONINPUT SPECIFICATIONInput Voltage: 115Vac/230Vac dual selectable. Input Connector: DIN 41612 at rear. Input Frequency: 47-63Hz.Inrush Current: Typ.25A @230Vac.Input Current: HSU45 0.88A@115Vac/0.44A@230Vac.Use T2.0A/250Vac fuse.HSU60 1.2A@115Vac/0.7A@230Vac.Use T2.5A/250Vac fuse.HSU100 2.2A@115Vac/1.2A@230Vac.Use T3.15A/250Vac fuse.Dielectric Withstand: Meet IEC950.EMI: Meet CISPR PUB.22 or FCC Class B. Power Fail Signal: Installed.Remote (Logic) Inhibit: Available.Hold-up Time: Typ. 20mS @115Vac/50mS @230Vac. Earth leakage: Typ. 0.3mA @230Vac.Overload Protection (OLP):Fully protected againstoutput overload and short circuit.Consult the factory for OLP setting.OUTPUT SPECIFICATIONOutput Voltage: See Ratings Chart. Output Current: See Ratings Chart.Output Wattage: Typ. 45 Watts for HSU45.Typ. 60 Watts for HSU60. Typ. 100 Watts for HSU100.Output Connector: DIN 41612 at rear. Line Regulation: Typ. 0.4%.Load Regulation: Main VO1 typ. ±1.0%.Aux. VO2 typ. ±2-3.0% (PR).±2.0% (Mag. Amp.)Aux. VO3 typ. ±2-3.0% (PR). Aux. VO4 typ. ±2-3.0% (PR).Noise & Ripple: Typ. 1% peak to peak. OVP: Built-in at main VO1 (latch).Adjustability: Available at main output VO1 andAux. output VO2 (Mag. Amp.).Remote Sense: Installed in main VO1.GENERAL SPECIFICATIONEfficiency: Typ. 70-75%.Switching Frequency: Typ. 100K Hz. Circuit Topology: Forward circuit.Transient Response: Output voltage returns in less than3mS following a 25% load change.Safety Standard: IEC950/UL1950.Power Density: 1.4 Watt / Cubic Inch for HSU45 & HSU60.1.9 Watt / Cubic Inch for HSU100.Operating Temperature: 0 to +50°C at full load.Derate linearly to +70°C at half load.Storage Temperature: -20 to +85°C.Temperature Coefficient: Typ. 0.04%/°C. Cooling: Free air convection cooling.Construction format: 6,8,10TEx3Ux160mm19” compatible Eurocard VMEbus standard.OUTPUT VOLTAGE/CURRENT RATINGS CHART 10/15/2001HSU45 SeriesMECHANICAL DIMENSIONS: MM [INCHES] WEIGHT: HSU45 537.0g (18.90 Oz.)SINGLE OUTPUTMAIN VO1 @# MODEL NO. Typ. Volt. HSU45-10/(E) 9.0A 5.0V HSU45-11 4.0A 12.0V HSU45-11/(E) 3.7A 12.0V HSU45-12/(E) 3.0A 15.0V HSU45-13/(E)2.0A 24.0V(E) With gas-tube for safety purpose.DUAL OUTPUTMAIN VO1 @# AUX. VO2 ◇●MODEL NO. Typ. Volt. Typ. Volt. HSU45-204.0A5.0V 2.0A 12.0V HSU45-21 2.0A 12.0V 1.5A 12.0V HSU45-22 4.0A 5.0V 1.2A 15.0V HSU45-23 1.5A 15.0V 1.5A 15.0V HSU45-24 4.0A 5.0V 1.0A 24.0V HSU45-251.0A 24.0V1.0A 24.0VTRIPLE OUTPUTMAIN VO1 @#AUX. VO2 ◇● AUX. VO3 ◇● MODEL NO. Typ. Volt. Typ. Volt. Typ. Volt.HSU45-30 3.0A 5.0V 2.0A 12.0V 0.5A 5.0VHSU45-31 3.0A 5.0V 2.0A 15.0V 0.5A 15.0VHSU45-32 3.0A 5.0V 2.0A 12.0V 0.5A 12.0V HSU45-33 3.0A 5.0V 1.0A 24.0V 0.5A 12.0V Symbol: " "OVP built-in. "@" Adjustable. "#" Remote sensing. "▲" Magnetic Amplifier. "●" Post Regulator. "◇" Floating ( or isolated) output.INPUT & OUTPUT CONNECTORS PIN ASSIGNMENTSAC INPUTSINGLE/DUAL/TRIPLE OUTPUTASSORTED SIGNAL ASSIGNMENT AC-L AC-N AC-G +VO1 -VO1 +VO2 -VO2 +VO3 -VO3 NC LOG. INH. +S -SPOWERFAILHSU45-1X28 30 32 4,6 12,14 - - - - 16,18,24,26 20 8 10 22 HSU45-2X28 30 32 4 6 8 10 - - 12,14,16,18,24,26 20 - - 22 HSU45-3X28 30 32 4,6, 8,10 12 14 16 18 24,26 20 - - 22 Mating connector:HSU60 SeriesMECHANICAL DIMENSIONS: MM [INCHES] WEIGHT: HSU60 707.0g (24.94 Oz.)SINGLE OUTPUTMAIN VO1 @# MODEL NO. Typ. Volt. HSU60-10 12.0A 5.0V HSU60-10B1 10.0A 6.0V HSU60-11 5.0A 12.0V HSU60-12 4.0A 15.0V HSU60-13 2.5A 24.0V HSU60-153.0A 19.0VDUAL OUTPUTMAIN VO1 @# AUX. VO2 ◇▲MODEL NO. Typ. Volt. Typ. Volt. HSU60-205.0A 5.0V 3.0A 12.0V HSU60-21 2.5A 12.0V 2.5A 12.0V HSU60-22 5.0A 5.0V 2.5A 15.0V HSU60-23 2.0A 15.0V 2.0A 15.0V HSU60-24 5.0A 5.0V 1.5A 24.0V HSU60-251.4A 24.0V1.4A 24.0VTRIPLE OUTPUTMAIN VO1 @# AUX. VO2 ◇▲ AUX. VO3◇● MODEL NO. Typ. Volt. Typ. Volt. Typ. Volt. HSU60-30 5.0A 5.0V 2.5A 12.0V 1.0A 5.0V HSU60-31 5.0A 5.0V 2.0A 12.0V 0.5A 15.0V HSU60-32 5.0A 5.0V 2.5A 12.0V 0.5A 12.0V HSU60-335.0A 5.0V1.5A 24.0V 0.5A 12.0V"●" Post Regulator. "◇" Floating(or isolated) output.INPUT & OUTPUT CONNECTORS PIN ASSIGNMENTSAC INPUTSINGLE/DUAL/TRIPLE OUTPUTASSORTED SIGNALASSIGNMENT AC-L AC-N AC-G +VO1 -VO1 +VO2 -VO2 +VO3 -VO3 NCLOG.INH.+S -S POWER FAIL HSU60-1X28 30 32 4,6 12,14 - - - - 16,18,24,26 20 8 10 22 HSU60-2X28 30 32 4 6 8 10 - - 12,14,16,18,24,26 20 - - 22 HSU60-3X28 30 32 4,6, 8,10 12 14 16 18 24,26 20 - - 22HSU100 SeriesMECHANICAL DIMENSIONS: MM [INCHES] WEIGHT: HSU100 943.0g (33.6 Oz.)DUAL OUTPUTMAIN VO1 @# AUX. VO2 ◇▲MODEL NO. Typ. Volt. Typ. Volt. HSU100-208.0A 5.0V 5.0A 12.0V HSU100-21 4.2A 12.0V 4.2A 12.0V HSU100-22 8.0A 5.0V 4.0A 15.0V HSU100-23 3.4A 15.0V 3.4A 15.0V HSU100-24 8.0A 5.0V 2.5A 24.0V HSU100-25 2.1A 24.0V 2.1A 24.0V HSU100-26E8.0A 12.0V0.5A 24.0VSINGLE OUTPUTMAIN VO1 @# MODEL NO. Typ. Volt. HSU100-10 20.0A 5.0V HSU100-11 8.0A 12.0V HSU100-12 7.0A 15.0V HSU100-13 4.2A 24.0V HSU100-16 3.6A 28.0V HSU100-182.0A 48.0VTRIPLE OUTPUTMAIN VO1 @# AUX. VO2 ◇▲ AUX. VO3 ◇●MODEL NO. Typ. Volt. Typ. Volt. Typ. Volt. HSU100-30 7.0A 5.0V 5.0A 12.0V 1.0A 5.0V HSU100-31 6.0A 5.0V 4.0A 15.0V 0.6A 15.0V HSU100-32 7.0A 5.0V 5.0A 12.0V 0.5A 12.0V HSU100-337.0A 5.0V 2.5A 24.0V 0.5A 12.0V QUAD OUTPUTMAIN VO1 @# AUX. VO2 ■† AUX. VO3 ◇● AUX. VO4 ◇● MODEL NO. Typ. Volt. Typ. Volt. Typ. Volt. Typ. Volt. HSU100-484.0A 12.0V 2.0A 24.0V 0.5A 12.0V 0.5A 12.0V HSU100Q-050MII 10.0A5.0V 1.0A 24.0V 1.0A 12.0V 1.0A 12.0V HSU100Q-050QII10.0A 5.0V1.0A 48.0V0.5A 12.0V 0.5A 12.0VSymbol: " " OVP built-in. "@" Adjustable. "#" Remote sensing. . "▲" Magnetic Amplifier. "●" Post Regulator. "†" Stacked on main output."◇" Floating(or isolated) output. "■" Couple common choke.INPUT & OUTPUT CONNECTORS PIN ASSIGNMENTSAC INPUT SINGLE/DUAL/TRIPLE/QUAD OUTPUTASSORTED SIGNALASSIGNMENT AC-L AC-N AC-G +VO1 -VO1 +VO2 -VO2 +VO3 -VO3 +VO4 -VO4 NCLOG.INH.+S -S POWER FAIL HSU100-1X28 30 32 4,6 12,14 - - - - - - 16,18,24,26 20 8 10 22 HSU100-2X28 30 32 4 6 8 10 - - - - 12,14,16,18,24,26 20 - - 22 HSU100-3X28 30 32 4,6, 8,10 12 14 16 18 - - 24,26 20 - - 22 HSU100-4X28 30 32 4 - 10 - 12 14 16 18 6,8,20,22,24 - - - - Mating connector:DIN41612-H15 Female。

2012培训教材-轻中卡操纵部分解析

2012培训教材-轻中卡操纵部分解析


3
2012年培训教材
2012年培训教材
轻卡变速器操纵部分大致相同（见图1），不同的地 方在于使用不同变速器时所用的软轴固定支架、软轴及挡 位标牌不同，见表1。
4
2012年培训教材
2012年培训教材
图1
5
2012年培训教材
变速器型号 HW20505TCL HW24505TCL 布置型式 变速器左操纵 变速器左操纵 变速器左操纵 HW25505TCL 变速器右操纵 软轴 选LG9704240010（2400） 手柄 LG9704240026 LG9704240003 LG9704240003 LG9704240002 软轴支架 LG9704240032 LG9704240032 LG9704240011 LG9704240019
2012年培训教材
2012年培训教材
轻型卡车变速器操纵部分结构简介
技术中心 2012年2月
2012年培训教材
2012年培训教材
2012年培训教材
2012年培训教材
目前我公司轻卡系列车型变速器操纵采用双软轴操纵， 该结构布置方便，结构简单，便于模块化装配。 通过优化设计，合理布置软轴走向，支架结构简单，重 量轻。 挡位清晰，换选挡力度适中。
2012年培训教材
26
2012年培训教材
2012年培训教材
图7
27
2012年培训教材
（6）软轴及气管走向与固定
2012年培训教材
轻卡系列车型使用的软轴最小转弯半径为200mm，因此
在固定软轴时要避免软轴直径小于200mm。软轴使用扎带固 定，避免和其他运动部件磨碰、干涉，尽可能远离排气管。 装HW50508C变速器时气管顺着软轴进入驾驶室，和软轴捆绑 在一起。
top242-250cn中文

top242-250cn中文

件下测量得到的。详情请参考关键应用部分。 3. 关于无铅封装形式，请参考订购信息。 4. 230 VAC或100/115 VAC倍压整流。
1 November 2005
版本 O 11/05
TOP242-250
目录
功能结构图.................................................................................................................................................................... 3 引脚功能描述 ................................................................................................................................................................. 4 TOPSwitch-GX 产品系列功能描述................................................................................................................................ 5
TOP242 Y 或 F TOP243 P 或 G
TOP243 R TOP243 Y 或 F TOP244 P 或 G
TOP244 R TOP244 Y 或 F TOP245 P 或 G
TOP245 R TOP245 Y 或 F TOP246 P 或 G
TOP246 R TOP246 Y 或 F