ICOM IC-7000功能细说

ICOM IC-R7000简易操作指南2010-01-06 04:10:55| 分类：接收机| 标签：|字号大中小订阅一、主要旋钮、按键及开关说明1、速度钮SPEED，用于扫描速度的调整，右旋到底扫描速度最大。

2、延时方式钮DELAY，用于扫描过程中检测到信号时停留延时方式。

OFF-信号出现多久就暂停多久；5-停留5秒钟；15-停留15秒钟；∞-只要检测到信号就停止扫描。

3、扫描键盘SCAN START/STOP，可设置六种扫描方式：重点扫描、频段扫描、选择信道扫描、同种制式扫描、所有信道扫描和自动扫描存贮。

①、重点扫描键PRIO，可在当前信道频率和重点设置的频率这两个频率间进行扫描。

②、频段扫描键PROG，设置了低频和高频后，则以TS旋钮设置的步进反复进行扫描。

③、选择信道扫描键SEL-M，在选择了的各个信道中进行扫描。

④、同种制式信道扫描键MODE，扫描与当前制式相同的各个信道。

⑤、所有信道扫描键MEMORY，扫描所有的存贮了的信道。

⑥、自动扫描存贮键AUTO-M，根据频段扫描中设置的高低频率，扫描并自动存贮到CH80~99信道中，因此CH80~99信道不作为常规存贮信道用。

4、衰减键ATT，天线衰减器，按下为衰减。

实际工作中一般不需衰减，不用按下此键。

5、频段键1GHz，按下此键则转换到1GHz以上的频段，最高监测频率可达1999.999MHz。

6、锁键LOCK，锁定键。

7、信道钮MEMORY CH，选择信道旋钮。

8、存写键WRITE，将频率存写入信道。

9、清除键CLEAR，清除当前信道内的频率数据。

10、确定键ENT，输入频率及其调制方式时的确定键。

11、步进钮TS(kHz)，频率步进钮，频段扫描时用，一般设为25 kHz。

12、音量钮AF GAIN，旋至合适位置即可。

13、静噪钮SQUELCH，扫描时要旋至合适位置。

14、FM频段开关（在背面板），因为是拆机下来的机子，有些内部线路可能有改动，对FM和FMn调制方式有影响，因此要根据实际情况将此开关拨至FM(1)或FM(2)档位，才能正常监听FM或FMn的信号。

ID7000系列智能读码器用户手册版权所有©杭州海康机器人技术有限公司2021。

保留一切权利。

本手册的任何部分，包括文字、图片、图形等均归属于杭州海康机器人技术有限公司或其关联公司（以下简称“海康机器人”）。

未经书面许可，任何单位或个人不得以任何方式摘录、复制、翻译、修改本手册的全部或部分。

除非另有约定，海康机器人不对本手册提供任何明示或默示的声明或保证。

关于本产品本手册描述的产品仅供中国大陆地区销售和使用。

本产品只能在购买地所在国家或地区享受售后服务及维保方案。

关于本手册本手册仅作为相关产品的指导说明，可能与实际产品存在差异，请以实物为准。

因产品版本升级或其他需要，海康机器人可能对本手册进行更新，如您需要最新版手册，请您登录海康机器人官网查阅（）。

海康机器人建议您在专业人员的指导下使用本手册。

商标声明●为海康机器人的注册商标。

●本手册涉及的其他商标由其所有人各自拥有。

责任声明●在法律允许的最大范围内，本手册以及所描述的产品（包含其硬件、软件、固件等）均“按照现状”提供，可能存在瑕疵或错误。

海康机器人不提供任何形式的明示或默示保证，包括但不限于适销性、质量满意度、适合特定目的等保证；亦不对使用本手册或使用海康机器人产品导致的任何特殊、附带、偶然或间接的损害进行赔偿，包括但不限于商业利润损失、系统故障、数据或文档丢失产生的损失。

●您知悉互联网的开放性特点，您将产品接入互联网可能存在网络攻击、黑客攻击、病毒感染等风险，海康机器人不对因此造成的产品工作异常、信息泄露等问题承担责任，但海康机器人将及时为您提供产品相关技术支持。

●使用本产品时，请您严格遵循适用的法律法规，避免侵犯第三方权利，包括但不限于公开权、知识产权、数据权利或其他隐私权。

您亦不得将本产品用于大规模杀伤性武器、生化武器、核爆炸或任何不安全的核能利用或侵犯人权的用途。

●如本手册所涉数据可能因环境等因素而产生差异，本公司不承担由此产生的后果。

IC-F7000中文说明书（快速中文说明）北京华诚广通科技有限公司/目录1．面板 (1)1．1 控制器面板 (1)1．2 主机面板 (2)1．3 麦克风 (2)1．4 LCD显示屏 (2)2．信道编程 (3)2．1 增加信道 (4)2．2 编辑已有信道 (4)2．3 删除信道 (5)3．ID编程 (5)3．1 进入初始设置 (5)3．2 Selcall选呼ID输入 (5)3．3 删除Selcall ID (6)3．4 ALE ID 码输入 (6)3．5 删除ALE ID 码 (6)4．话音接受或发送操作 (7)5．选呼操作 (7)5．1 选择信标呼叫 (7)5．2 选择呼叫 (7)5．3 ALE呼叫 (8)5．4 结束ALE呼叫 (9)5．5 ALE探测 (10)6．VFO〈频率〉方式 (11)6．1 CHANNEL /VFO 方式选择 (11)6．2 调整频率 (11)6．3 分频操作 (12)7．简易方式操作 (13)8．快速设置方式 (13)8．1 进入快速设置方式 (13)8．2 工作方式选择 (13)8．3 电台发射功率选择 (13)8．4 予放操作 (13)9．扫描 (13)9．1 进入扫描编辑 (14)9．2 打开、关闭扫描 (14)9．3 扫描组选择 (14)1．面板1.1 控制器面板电源按键：[I/O]按下，打开电源。

当电源已打开，快速按下[I/O]，进入“快速设置方式”。

再次按下[I/O]，退出“快速设置方式”。

按下约1秒钟，关电源。

静噪键：[MUTE]按下可选择静噪方式：话音静噪，信号电平静噪，选呼静噪。

调谐键：[TUNE]按下约一秒钟，启动手动调谐。

上/下键：[UP]/[DN]选择信道或设置方式的项。

扫描键：[SCAN]按下启动或停止扫描。

呼叫键：[CALL]按下进入呼叫菜单，再按退出。

按下约一秒钟发送呼叫。

1.2 主机面板1.3 麦克风[PTT]：按下讲话，释放接收。

[DN]/[UP]：下/上按键。

C=（m2-m1）×1000 / QT
式中：C----粉尘浓度，mg/m3
m1---采样前滤膜质量，mg
m2---采样后滤膜质量，mg
Q----采样流量，L/min
T----设定的采样时间，min
其电器原理框图如下：
图1
三、仪器结构
仪器由探测系统、电源系统、单片机系统及采样和流量控制系统组成。射线通过滤膜达到传感器时，引起传感器的电信号发生变化而产生脉冲输出。该脉冲经处理电路的处理得到一个标准脉冲，达到单片机的输入要求，送至单片机的输入口，按程序要求进行测量，并将测量数据存储于单片机的RAM中的固定地址。仪器在程序的控制下，可进行N1、N2的测量，还可进行固定流量和选定时间的采样；从而达到既可控制采样，又可控制测量的功能，最后将测量结果显示在显示器上。
注2：应将装有滤膜的滤膜夹按水平方向紧贴测量腔的上沿缓慢插入直至测量腔的尽头（底部）。
1.测量空白膜
选择“1、空白”，进行空白膜的测量，按“确认”键后，显示：
其中XX为测量空白滤膜的剩余时间，为10～99秒，出厂时已设定好(默认为30秒)，无须用户操作。
待测量完毕，蜂鸣器会发出“嘀”的一声，表示测量完毕，此时显示器显示：
GL TECH虽然已经尽力确保本用户手册中文字表达的准确和完整，但仍希望您在发现任何错误时，能及时通知GL TECH。
GL TECH为了使您能使用到最先进的产品，将不断提高我们的技术，GL TECH有权随时更改本用户手册中所载的内容，请原谅不事先通知。
本产品已通过防爆认证和煤安认证及计量认证。粉尘仪产品铭牌上印有防爆标志(EX)和煤安（MA）认证标志，产品铭牌上的仪器编号为五位阿拉伯数字：7* * * *。
此时仪器开始采样，泵开始工作。显示器上将动态显示剩余采样时间，待采样完毕，仪器发出“嘀”的一声提示采样结束，显示器显示：

Modifying the Icom IC 7000 Export version No 8 to receive PAL TV in South Africa and to open up the TX frequency range.Gary Immelman ZS6YIIn South Africa the TV audio frequency is different to that used in other parts of the world. We use 6 MHz instead of 5.5 MHz as used in the Icom IC 7000 export #8.The ceramic trap filters have to be replaced. They are situated at the bottom of the Main Board. This board needs to be completely taken out of the radio then obviously replaced once the new filters have been fitted.The shift register diodes need to be changed in order to open up the frequency range and enable the television tuner. A number of diodes are removed and one diode installed where no diode originally existed.METHOD1.Remove the top cover of the radio and unclip the speaker plug.2.Remove the CPU/Logic unit. (Silver box)3.Remove the DDS unit.4.Remove all coaxial plugs and ribbon cables from the board. Be extremelycareful when removing the two ribbon cables at the front of the radio asthey can be pulled out of the PA unit. It is extremely difficult to reinsertthem into the PA unit.5.Remove the spring clip at the back of the Main board holding IC 2602 tothe chassis.6.Remove the Main Unit – This is the unit to be modified.7.Remove the two SMD ceramic trap filters situated underneath the boardas seen from the top view.8.Replace old filters with 6 MHz ceramic trap filters obtainable from anyTV repair shop. Cost R8.00 each.9.Remove shift register diodes. Fit one diode at right hand side of the boardas viewed from the front of the radio looking towards the back,orientating it with the cathode to the left.10.P lug in the two ribbon cables from the DDS unit into the Main boardbefore fitting the Main board to the chassis.11.R eplace all screws and tighten.12.P lug in all the cables, re-fit the CPU/Logic unit etc.13.R eplace the top cover. Don’t forget to plug in the speaker.Label on IC 7000 box #8 Export modelStep 1Step 2Remove the DDR unit first then the main boardStep 3Very carefully unplug ribbon cables. Don’t pull on them!Step 4Original 5.5 MHz SMD ceramic filtersStep 5Step 6Step 7New Diode positionsStep 8OPERATIONConnect the power supply to the radio and couple a TV antenna terminated in a PL259 plug to the VHF antenna socket of the radio. (Right hand side of the radio as seen from the front looking towards the back).When you switch the power on a warning message will appear on the blue screen. Press Yes that you acknowledge the warning.The radio reverts to the original frequency you had the radio on before embarking on the modification.To activate the TV receiver push and hold in the set button (Volume controlsituated at the top left hand side of the radio). If the TV receiver does not comeon, push the set button (volume control) once again. The TV receiver will now come on.It is advisable to switch on the preamplifier.By using the Band up and down buttons you can change TV channels, select a channel.To change the frequency press the ADJ button and tune in the station using your VFO knob. You can do quick frequency movements by pressing the TS button.Once you have found a station (audio only) press SET at the bottom of the screen. You should now see a picture.You can now fine tune the picture by rotating the VFO knob.Once everything is tuned perfectly press the volume control (set) button to store the station into the channel number previously selected.ACKNOWLEGEMENTSI wish to thank my son Quintin ZS6IY for his help with the soldering of these minute components using his hot air soldering station (surface device soldering station).OM Eddie Leu ZL3TEL for his assistance and photos of the New Zealand expanded frequency range.OM Paul Hayden VK4ZBV for information on the Australian and South African audio frequencies.Finally OM Ken G3SDW who initially discussed changing the sound filters with me. His email inspired me to get cracking.In ConclusionFor those South African Hams who have purchased the American model. I am working on a modification to change the NTSC system to PAL. It involves changing a number of parts on the main board. It won’t be difficult but procuring the parts may be a challenge.If I can get hold of the oscillator and coils I will do the modification then update everyone as to its success.73 Gary Immelman ZS6YI。

频谱仪非线性失真探讨及在杂散测量中的应用作者：暂无来源：《上海信息化》 2020年第6期文/范昱洲在进行大功率信号测量，尤其是杂散测量时，频谱仪和辅助测试设备使用方法上的细小差别，可能会使测量结果截然不同。

因此，探讨测量误差产生的原因，并研究如何减小误差，是十分有必要的。

在无线电管理工作中，工程师们通过监测手段观察并分析各种无线电频谱信号。

一个未经登记的不明无线电信号有可能来自非法设置的无线电台站，也可能来自某个合法无线电台所产生的谐波和杂散信号。

无线电监测中，通过开场测试的手段，可以定性观察不明信号；通过传导测试，则可以定量、准确地测定不明信号的来源。

无论是开场测试还是传导测试，都要用到频谱分析仪。

频谱分析仪的输入混频器是非线性器件，在满足一定条件时，自身会产生谐波和杂散。

在测试过程中，谐波和杂散信号会与大信号同时进入频谱仪，这些无用信号如果落到被测信号的频率范围内，则会对最终测试结果造成误差。

本文通过一项实验，讨论并验证了这种现象，并结合业余无线电台的谐波传导测试，提出了一种实用的解决方案。

谐波测试中对频谱分析仪非线性特性的要求射频测试和测量遵循10dB原则，即测试系统的指标应优于测量限值至少10dB。

测试误差的通用计算公式为：Error+=20*lg[1+10^（A-B）/20）] （1-1a）Error-=20*lg[1-10^（A-B）/20] （1-1b）式中，Error+、Error-分别表示正负误差，A是测试系统的指标，B是测量限值。

如果A-B=10dB，即系统指标优于测量限值10dB，那么测试误差为+2.4/-3.3dB。

结合本文讨论的测试案例，假设被测业余无线电台的谐波要求在满功率发射时应小于-60dBc。

按照10dB原则，要求频谱分析仪的二次谐波至少要优于-70dBc。

通过研究目前市面上的高端频谱仪指标，发现当载频输入为-15dBm时，频谱仪的二次谐波指标典型值为-60dBc，显然不能满足测试要求。

ICOMIC-7000功能细说(一)来源:《无线电》杂志 2009.01 作者:杨法（BD4AAF）自从ICOM公司的IC-7000多功能电台上市以来一直备受业余无线电爱好者的关注。

IC-7000较传统通信电台有太多的创新，这对无论是刚入门的新手还是年过花甲的资深HAM都产生了巨大的吸引力。

IC-7000有两个最大的卖点就是TFT彩屏显示和IF DSP技术的应用，其他数字录音、内置RTTY解码、全遥控手持话筒、频谱显示、HF/VHF/UHF 多频段多模式操作、机头分离、视频输出、SWR图形显示、电视接收（有版本限制）等更是举不胜举。

这也注定了IC-7000是一部多功能、很耐玩的电台。

IC-7000经过在HAM界数年的实战，有很高的购入比例，也有较高的换手率。

对于该机所提供的功能大家基本比较满意，对其100W发射性能也没有多大异议，对其音质问题各人看法不同，这也与话筒特性和设置有关，目前争议比较大的是IC-7000的接收性能。

很多业余无线电爱好者在购买IC-7000前通过产品宣传和有限知识的了解，都默认为这部花费近万元的小电台是一部融合了目前最新数字化科技的高档、高性能产品，其性能在传统电台上有质的飞跃。

随着爱好者对该机器使用的深入和与其他电台对比的机会增多，我们可以客观地来重新认识一下这部电台的特性。

◆外观与特点从外观体积上来看，IC-7000是一部定位于车载，并可以作为便携电台使用的“小而全”的电台（尽管没有内置天调），体积较传统标准体积的基地式电台小得多，加上机头分离功能（需要另外购买专用的机头分离线，由于其接口是专用的，所以不能像FT-857D、IC-2720H那样轻易用水晶头自制），非常适合安装在各种中小型车辆上。

说到天调，绝大部分中小体积电台所装备的内置自动天调调节范围都不大，大部分匹配范围在16.5～150Ω，也就是说可以改善SWR<3的天线系统，与一些室外长线自动天调和手动天调的调节范围相差甚远，所以也被称谓“锦上添花”型的天调，主要是用来扩展谐振型天线的工作带宽。

总括：IC-7000是全球HAM界倍受好评的IC-706系列(共计三代机型IC-706/IC706MKII/IC706MKIIG) 基础上打造的第四代具备双数码处理器的全模式全频段电台，内置多项创新理念和多种人性化的设计，更让HAM知道，DSP不仅仅只是可以用于声音的处理。

IC-7000仅为进阶发烧级玩家而存在，看下去，你便知道哪传闻的价格是否等值甚至乎超值与否…….使用报告：实时数码中频信号处理器，完全替代传统模拟式中频电路，基于两个强大的高速数码DSP 信号处理器实现。

过往在传统电台上使用的中频滤波器选件，在IC-λ 7000上，已经给数码处理器所替代，不再需要另外购买各类高价的、各种参数的和针对各种应用的中频滤波器选件(补品)；在图视化的帮助下，提供人性化特征的中频数码处理优势：允许用户随心地更改中频带宽(SSB：3.6KHz-50Hz，CW：高频起点略低)，同时，基于IC-7000机体内新增加的大容量EEPROM储存器(不需钮扣电池保存数据，下面另外有针对于此更多的应用介绍)，用户被允许对应每一个HAM用频段，分别被自定义三种频率带宽的宽、中、窄过滤器(简称为：IF Filters Profiles)，HF频段多达10个，共计就是30个中频过滤器设置；在VHF、UHF中，强制为宽17KHz、中10KHz、窄7KHz，不允许自定义。

同样基于两个强大的高速数码DSP信号处理器，为数码中频信号传送至模拟低频放大电路之间，提供两个实时数码通带滤波器，用于处理来自于数码中频信号释出的矢量低频，ICOM 更为此注册了专用名称PBTλ (PassBand Tuning)，人性化的设计在于：图示化操作界面，形象化地表示两个PBT相对核心频率的状况，旁边则显示PBT调整时频率带宽的重要参数。

必不可少的还有两个能够独立工作的MNF数码低频陷波器，用户允许把两个数码陷波器分别独立地选用不同的宽、中、窄陷波带宽进行数码陷波处理，甚至关闭某一个功能单元均可，ANF数码低频声表面平滑处理技术，使用过程中，发现功能不是想像中一般，按下便能够即时体验到改变，仅在信号不良的情况下，DSP检测后自动启用，而此开关仅是强制关闭的作用。

网康互联网控制网关（Internet Control Gateway, NS-ICG）是一款软硬件一体化、性能卓越的互联网控制管理产品。

NS-ICG为网络管理者提供各种互联网接入环境中的灵活身份确认、合规准入、网页过滤、应用控制、带宽管理、外发合规检查，内容留存审计，结果分析等功能。

主要功能：1、精细应用识别，管控您的网络●DPI+DFI+XAI深度行为识别技术，准确识别上百种P2P应用，并加以限流、封堵等精细化控制●支持对市面主流30余种IM聊天工具进行识别并控制●能够识别用户论坛发帖行为，针对发帖敏感关键字设置过滤，并支持主动报警●对开心网、QQ农场等网页游戏，以及魔兽世界等多种主流网络游戏进行识别并控制●支持30余种主流炒股软件，并可细化识别行情查询与在线交易，加以区分控制2、专业网页分类，健康您的网络●国际领先的网页预分类技术，对含有有害、不健康内容的网页进行过滤，创建文明健康上网环境●高达2000万条全球规模最大的中文URL数据库，全面覆盖中文地区站点，确保分类准确无遗漏●本地智能识别分类引擎，采用专业自学习算法为URL数据库覆盖范围外的网址提供实时智能识别3、终端用户准入，规范您的网络●20余种用户身份识别/认证方式，确保入网用户身份合法有效，避免外来隐患●对计算机终端环境进行管理，帮助管理者实施计算机准入规范●如：必须安装杀毒软件方可上网；禁止安装、运行与工作无关的应用程序等4、带宽合理分配，优化您的网络●精确识别各种互联网应用，包括各种对带宽占用极大的主流P2P软件与在线视频软件●基于应用或用户对流量进行管理，对指定类型的流量进行限速，避免占用过多网络带宽●为关键业务提供带宽资源保障，保留足够可用带宽，保障服务质量5、实时监控审计，洞悉您的网络●查看上线用户的网络使用时间与流量信息，及时发现异常用户并加以处理●全面了解用户上网行为，包括网页访问、邮件收发、即时聊天、论坛发帖、网络娱乐等所有互联网活动●对于用户通过邮件、聊天、论坛等外发的言论信息进行合理监控，及时过滤有害信息网康互联网控制网关NS-ICG 7000-70 适用于：80000人规模，4Gbps出口带宽的网络环境参数规格：NS-ICG7000-70产品规格参数见下表：下面是赠送的几篇网络励志文章需要的便宜可以好好阅读下，不需要的朋友可以下载后编辑删除！！谢谢！！出路出路，走出去才有路“出路出路，走出去才有路。

ICOM IC-R7000使用说明书一、主要旋钮、按键及开关说明1、速度钮SPEED，用于扫描速度的调整，右旋到底扫描速度最大。

2、延时方式钮DELAY，用于扫描过程中检测到信号时停留延时方式。

OFF‐信号出现多久就暂停多久；5‐停留5秒钟；15‐停留15秒钟；∞‐只要检测到信号就停止扫描。

3、扫描键盘SCAN START/STOP，可设置六种扫描方式：重点扫描、频段扫描、选择信道扫描、同种制式扫描、所有信道扫描和自动扫描存贮。

①、重点扫描键PRIO，可在当前信道频率和重点设置的频率这两个频率间进行扫描。

②、频段扫描键PROG，设置了低频和高频后，则以TS旋钮设置的步进反复进行扫描。

③、选择信道扫描键SEL ‐M，在选择了的各个信道中进行扫描。

④、同种制式信道扫描键MODE，扫描与当前制式相同的各个信道。

⑤、所有信道扫描键MEMORY，扫描所有的存贮了的信道。

⑥、自动扫描存贮键AUTO‐M，根据频段扫描中设置的高低频率，扫描并自动存贮到CH80~99信道中，因此CH80~99信道不作为常规存贮信道用。

4、衰减键ATT，天线衰减器，按下为衰减。

实际工作中一般不需衰减，不用按下此键。

5、频段键1GHz，按下此键则转换到1GHz以上的频段，最高监测频率可达1999.999MHz。

6、锁键LOCK，锁定键。

7、信道钮MEMORY CH，选择信道旋钮。

8、存写键WRITE，将频率存写入信道。

9、清除键CLEAR，清除当前信道内的频率数据。

10、确定键ENT，输入频率及其调制方式时的确定键。

11、步进钮TS(kHz)，频率步进钮，频段扫描时用，一般设为25kHz。

12、音量钮AF GAIN，旋至合适位置即可。

13、静噪钮SQUELCH，扫描时要旋至合适位置。

14、FM频段开关（在背面），对FM和FMn调制方式有影响，因此要根据实际情况将此开关拨至FM(1)或FM(2)档位，才能正常监听FM或FMn的信号。

二、存写信道。

I C-7000P a n/T i l t I P S u r v e i l l a n c e C a m e r a Quick Installation Guideby Edimax Technology Co, LTD. all rights reserved. No part of thisAnchorFrameScrew (P head M3.5X25)When the installation is completed, you will get ” CAM_EZ Search “ as follows CAM_EZ Search is a camera search utility comes with this product. It can search all IP CAMs connected to LAN by sending broadcasting packets. After IP CAM responds the inquery packet, the utility will display a list of all IP CAM found on LAN. And it allows you to modify the settings of specified IP CAM, such as IP address or the name of IP CAM.figure 1B. Make sure the IP addresses of PC and IP CAM are on the same networkOpen and execute CAM_EZ Search (as shown in Figure 2). The system will scan the IP-CAM that you just installed automatically. Then, you will find255IC-7000 in the column of Camera Lists. Click 255IC-7000 with left mouse button. You can see the default settings of IP-CAM.Figure 2 2.3 N ETWORK S ETUPOpen and execute CAM_EZ Search (as shown in Figure 3). The system will scan the IP-CAM that you just installed automatically. Then, you will find255IC-7000 in the column of Camera Lists. Click 255IC-7000 with leftFigure 3z Fill static IP Address as shown below. (If you do not know your IP address, please contact your ISPshown below)`IC-7000 QIGP a n/T i l t I P S u r v e i l l a n c e C a m e r aPV1.0IC-7000 USER’S GUIDE PAGE 11/11 Rev.。

Icom IC-7000 Frequently Asked Questions (FAQ)This guide was created to answer the most commonly asked questions about the Icom IC-7000. The goal is two-fold:1) Condense the discussions found in the Yahoo group to the raw information providing a definitivesource for the FAQ reader2) Remove these recurring questions from the group to improve the “signal to noise ratio” Instructions for updating, correcting and adding information are located at the end of this FAQ.IC-7000 Unique Features• The IC-7000 was the smallest multimode radio available at its introduction (and the time of this writing)• It was the first truly mobile radio to feature IF-DSP (customizable filters – nothing to buy)• Filter width adjustable by mode with “sharp” and “soft” shape factors• Dual ADI Blackfin DSP Processors - feature set similar to the IC-7800, IC-756 Pro III• ACG loop performance controlled by DSP• Auto notch plus dual manual notch filters for up to 70 dB of attenuation• Noise blanker features adjustable pulse width and depth of cut• Internal RTTY decode and dual peak RTTY filter• High stability crystal oscillator is standard• Voice synthesizer standard• VFO knob includes a working “spinner”• The VFO knob tension is adjustable from free to tight and detented – great for mobile operation!• Microphone and external speaker jacks on both the head and body• Color composite video output available at all times to support a larger monitor• Multifunction display shows complete receiver status, S-meter/power output, ALC, compression, SWR and final temperature on a single screen• Semi-real-time spectral display 25-500kHz wide with peak hold and SWR sweep meter• VHF NTSC TV reception with internal modification• Many functions, including band stack registers, direct frequency entry, mode, filters and speech synthesizer available directly via the microphone (no menu navigation required) • Two programmable function keys on microphone for most used functions• CW/Voice memory keyer with 4 memories each and internal recorder feature• CW/voice keyer directly accessible with simple box described in manual• Thermostatically controlled fan• Less receive standby current draw than the IC-706MKIIG• Remotely mountable head• 6-pin data jack and 13-pin accessory jack• Customizable opening messageUser Measured SpecificationsPower outputThe IC-7000 maximum output power drops as voltage drops. This behavior is consistent with other radios as shown by the Yaesu FT-450 results below.The band tested below was not specified.13.84 2.0 17 9313.49 2.0 17 9213.01 2.0 17.5 9212.50 2.0 17.5 9012.02 2.0 16.0 8011.50 2.0 14.5 7011.01 2.0 14.0 6010.50 2.0 12.5 5010.00 2.0 11.5 409.50 2.0 XMIT FAILEDVoltage measured at power supply. Cables supplied by Icom. Power out as indicated in CW mode on attached tuner into a dummy load. At full voltage I had a full 100w PEP on SSB.<Marc W0KYZ>By comparison, these are the measurements that I obtained from a new Yaesu FT-450AT late last year: 13.8V - 100W12.5V - 100W12.0V - 75W11.5V - 68W<VR2AX> I looked up the % charge chart for my Trojan Deep Cycle battery:100% 12.70V80% 12.46V75% 12.40V50% 12.20V45% 12.16V25% 12.00V10% 11.94V5% 11.92V Discharged @ 11.90V<Jack_son>Receive standby currentIcom specs say 1.3A on receive squelched and 1.6A full volume.I checked mine. I got 1.36A two minutes after power up with default settings on 2m FM. Full volume (painful) was1.52A. I found I could save about 40mA by reducing "LCD Bright" to minimum (and still read the display) and another 40mA by turning off the switch backlighting. The readings were a little tough to validate because the fan is variable speed and can affect the readings by more than 100mA.These numbers seem consistent with the published Icom specs. It's not exactly milliamps but it's still 500mA less than the IC-706MKIIG specs. <Scott N7SS>How do I…?How do I hook a monitor to my IC-7000?The IC-7000 uses a 1/8” mono mini jack to provide composite video out. Any monitor, TV or VCR that supports composite video input (yellow RCA jack) can be used as a display. Although the 1/8” mini jack is small, it’s not a standard video connector. Radio Shack offers a 6 foot cable (Catalog #: 42-2444) for only a few dollars that has a 1/8” mini plug to RCA plug and will connect the IC-7000 directly to a standard composite monitor/TV.It is also possible to use an adapter to convert the 1/8” mini jack to an RCA to allow the use of a standard RCA cable. Rigid adapters should be used with caution because the jack can be pulled off the main board if too much torque is applied.“To use with a standard computer monitor, it is necessary to convert the composite video to RGB video with a device like the KWorld TV Box 1680ex.I use this one and it works ok but the above is better: /mpd/tvbox9.html<Steve Ellington, N4LQ>How do I use a Bluetooth headset with my IC-7000?“Works great. See link below from K7SFN. /projects/bluetooth.html”<Dave, KI4KQ>How do I connect more than one CI-V device to my IC-7000?The Icom CI-V interface is a serial bus design. This allows more than one device to be connected to the radio CI-V interface (amplifier, antenna switch, SteppIR antenna, additional radios, etc.). “To connect these devices get a flexible adapter like the Radio Shack 42-2437 or even a three-way adapter like the Radio Shack 42-2458”. <Doug Faunt, N6TQS>How do I get better transmitted audio?The IC-7000 was designed as a mobile radio and the microphone was intended to be used in high noise environments. Although the Heil microphones and W2IMY equalizers provide excellent audio, many people want to maintain the functionality of the stock microphone and get better audio without the expense of these options. AB5N has created a modification for the stock microphone at/ that creates a “hotter” microphone and higher quality audio. There is also a microphone modification posted at http://www.mods.dk/.The IC-7000 has two microphone jacks but the Icom manual specifically states that only one microphone should be used at a time. This is likely because both microphones would be hot at the same time. Some have suggested a mute switch (disabling the mike element) in the stock microphone. This would allow the stock microphone to be used as a “remote control” in one mike jack with a headset in the second mike jack.How do I use my IC-7000 on 60m?Page 40 of the IC-7000 manual provides information on 60m operation and is quoted below.To assist you in operating the 5 MHz band correctly within the rules specified by the FCC, transmission is impossible on any 5 MHz band frequency other than the 5 frequencies indicated in the table below.IC-7000 Display Frequency* FCC Channel Center Frequency*5.33050 MHz 5.33200 MHz5.34650 MHz 5.34800 MHz5.36650 MHz 5.36800 MHz5.37150 MHz 5.37300 MHz5.40350 MHz 5.40500 MHzNOTE: We recommend that you store these frequencies, mode and filter settings into the memory channel for easy recall.*The channel center frequencies that are specified by the FCC, show the center frequency of their passband. However, the IC-7000 displays carrier point frequency, so set 1.5 kHz below from FCC channel center frequency.How do I get full power output when transmitting?The IC-7000 was designed to deliver full power output at 13.8 volts. This is the voltage provided by most power supplies and the alternator output of a vehicle. The voltage table at the beginning of this FAQ shows output as voltage drops. When using the radio from a battery it is necessary to use the largest possible power cabling and a battery voltage booster to maintain the 13.8 volts required for maximum output.I use my IC7000 on CW almost exclusively, and I operate ONLY mobile. I use the N8XJK booster / with no problems at all. For a while I used it with the RF sensing, but no longer do so... not because of any performance problems, but because when the engine is running I don't need the booster, and when in receive I don't hear any noise problems from the booster, so I decided to so away with the additional wiring needed to use the RF Sensing. <Dave- K9FN>“I will ad that the MFJ-4416 voltage booster has helped greatly when the vehicle isn't running. This radio and many other mobiles do not Tx full output power on less than 13+ volts. So either get a battery voltage booster or keep the vehicle running.” <AE5MH>How do I use my radio in VOX mode?“Two things two check. You are in a voice mode and you have turned VOX on. I just tried it and it works with the stock 151 microphone. Be sure the word VOX shows up on your display.” <Steve EllingtonN4LQ>“Turn the VOX Gain up reasonably high, and turn the Anti-VOX as low as you can with out the speaker triggering the VOX. My 7000 works great with stock microphone in VOX mode.” <Dave - KI4KQ>How do I access the CW/Voice memory keyer?The CW and voice keyer options are accessible through the menu. When using the keyers via menu, it is not possible to access other features or the popular multimeter screen. There is a simple resistor network with switches shown in the manual to allow immediate access to the CW/voice memory keyer.“I made the device in the photo for solve this problem using the circuit at the 135 Page. I use my 7k for contesting and expeditions so the voice message function is a powerful help but use it via the menus is complex. /ea1nt/7kbox.htm <Luis EA1NT>How do I use a Turbo Tuner and screwdriver antenna with an IC-7000On the Turbo Tuner Web site, N2VZ is shipping Turbo Tuners setup for the 7000 AND the software update for Turbo Tuners that were programmed for 706, to make it a 7000 tuner. He will email you the update to flash your 706 Turbo Tuner thru the RS232 port on the Turbo Tuner./<Kent KQ4KK>How do I enter DTMF tones for Echolink/IRLP or repeater control?The stock IC-7000 microphone has many functions but like the IC-706 family, it can’t generate DTMF tones. There are two solutions offered by Icom. The first option is the same DTMF microphone used by the IC-706, the HM-154T.There are also 4 DTMF memories of up to 24 digits described on page 67-68 of the IC-7000 manual. This allows recording command/control sequences in these memories. Set Menu Option 38 specifies which DTMF option appears when F-2 is pressed in the menu.Can I use my IC-706 accessories with my IC-7000?Most accessories from Icom and third parties will work directly with the IC-7000. There are a few exceptions. The Icom remote kit is different for the IC-7000. The body and head bracket are the same but the remote cable has 10 pins, rather than only 8 pins. The microphones are largely compatible but the IC-7000 does not have an audio output line in the microphone cable. This could effect some TNC cables and older Heil headsets. The later Heil headsets have a separate speaker plug. There have also been some compatibility issues with third-party tuners (LDG and Turbo Tuner) although ROM upgrades are generally available to address these issues.Where do I find…?DC Power connector“New HF radios from Japan, introduced in the past 5 years operating on 12V DC, like the ICOM IC-7000, Kenwood TS-480, Yaesu FT-450, Yaesu FT-2000, and the new ICOM entry level radio all use the same connector, wired the same way.” <John Bee N1GNV – Quicksilver Radio>Quicksilver Radio - /DCpower.htmTower Electronics - /Powerwerx - /Wimo - http://wimo.de/cgi-bin/verteiler.pl?url=netzgeraete-zubehoer_d.htmlMonitorThere are too many monitor options available from too many sources to list here. The IC-7000 provides composite video out. This can be run into most TV sets and VCRs with the appropriate cable (1/8” monaural mini plug to RCA plug).Small monitors can often be found on eBay and any place that sells car audio/video. In-dash DVD players and many navigation systems include a composite video input. There has even been some discussion that a Toyota Prius instrument panel has an input that could be used for an IC-7000.Icom uses a 7” Xenarc 700YV monitor in the display they use at hamfairs. This monitor is more than what is necessary for most users. The rated LCD brightness of 500 cd/m² and contrast ratio of 400:1 crates a nice image. These are the two most important numbers when determining the quality of an LCD display. Often these numbers are not available and the price is the only indication of the relative monitor quality.CI-V computer interfaces for serial and USBIcom sells the CT-17 interface, which offers 4 CI-V ports and a single DB-9 serial port. There are a number of less expensive options available on the market in both serial and USB. These are commonly found on eBay. Radio Shack also has some scanner programming cables that will work.“I purchased the Radio Shack 20-047 USB Programming Cable & Driver Software today.(the number and description is right off their label)I followed their directions and connected the USB plug after installing the driver. It connects at 19,200 bps and has not given one sign of improper connection...This is faster and easier than the CT-17.I used a 20 foot stereo extension to get to the ICOM and used the stereo to mono adapter supplied with the interface to plug in at the radio end of the connection.18 hours later, I am sure this is the best way to go.” <im2old2run>Interfaces are also available from:West Mountain Radio - /RIGtalk.htmMFJ /Product.php?productid=MFJ-5383IControl softwareThe IC-7000 is similar to the other Icom HF radios and can use much of the same software written for the IC-706 family (although the radio address may need to be changed). More software is offering native IC-7000 support. One of the first and best is Ham Radio Deluxe (HRD) and is available for download at no cost from /.Memory programming softwareThere are a number of packages specifically designed to program the memory channels in the IC-7000. Rumtrol7k http://www.dl2rum.de/rumsoft/RUMtrol7K.htmlIC7000BKT /ic7000bkt_en.htmCI-V Cat.program/Memory Manager http://www.tellina.nl/software/Radio IssuesThe IC-7000 runs hot even on receiveThere are reports of the IC-7000 running hot despite most of the radio body being cooler than the IC-706. There are three points in particular that can run warm; the display because of the backlight, the area behind the speaker where the DSP ICs are heat sinked and the actual heat sink on the back of the radio. Here is a chart showing relative temperatures of various devices with color displays. The temperatures below were taken with an infrared thermometer after a 24 hour warm-up period at 71 degrees F with no transmit.Icom IC-7000 91°F 33°CIcom IC-2800 107°F 41°CSharp 15” TV/Monitor 85°F 29°CG2G 5” TFT Portable Monitor 106°F 41°CInitial 7” Portable DVD Player 85°F 29°CThe display runs about 91°F. The heatsink on the rear runs 99-103°F (in receive). The cooler areas on the back are 92-96°F. The temperature on the top ranges from 95-109°F. The area directly behind the speaker is the hottest at 109°F. This is directly over the silver box containing the DSP chips.The thermometer on the multimeter display shows the rear heatsink temperature. The final output transistors use this heatsink.Many users have installed fans over or behind the radio to increase the airflow over the chassis. Care must be taken with fans in dusty environments. There is also a fan modification published onhttp://www.mods.dk.Strange behavior on transmit (shutting down, resetting, changing frequency, etc.) This is most commonly a grounding/RFI issue. Make sure the radio and antenna are properly grounded. If the separation cable is being used, attempt to route it away from RF sources and be sure to use the screw to attach it to the radio.Audio feedback during transmitCheck to make sure you don't have the "monitor" turned on. Usually, you just use the monitor when transmitting digital modes.• Push SET button (AF gain control knob) upper left hand corner of radio.• Go to "Set Mode" > OTH > Monitor. Set to OFF<Brian, KC4UKR>High frequency (8kHz) tone in audioVery early models of the radio had a noticeable tone at 8kHz. This was not audible through the internal speaker because the internal speaker is “communications grade”, meaning it has a frequency response limited to voice frequencies. It was also not audible when using Heil, David Clark and othercommunications headphones or speakers. It was most obvious when using inexpensive “Walkman” style hifi headphones which are excellent at reproducing non-voice frequencies.Icom addressed this within a few months after production began with some capacitor and grounding changes. This modification should be available at no charge for units in warranty.Low level hiss in audioMany radios have a small amount of hiss (white noise) when the volume is set to the minimum value. This hiss remains at a constant level as the volume is increased and is quickly overwhelmed by signal audio. The hiss is apparently internally generated. There is no known solution but some users insert attenuators in the audio line. Since the hiss is a fixed level, it will reduce the hiss level while allowing the signal level to be increased with additional AF gain.This audio hiss is very low through the internal speaker because it is “communications grade”, meaning it has a frequency response limited to voice frequencies. Any external speaker or headphones should also be designed for communications work, rather than hi-fi, so as to minimize this issue.S-meter reads lowThe IC-7000 S-meter is very accurate but as a mobile unit is calibrated to read accurately with the preamp enabled.Changing the transmit audio bandwidth results in poor transmit audioThe Icom IC-7000 supports changing the transmit audio bandwidth. There are three predefined settings which can be modified. Because it appears the transmit equalization feature was cut, there is no way to rebalance the audio as the bandwidth is narrowed. This makes the audio quality very poor at narrow bandwidths. If DX-quality narrow audio is desired, the best solution is a good DX microphone or an external equalizer like those from W2IHY.。

HF/VHF/UHFALL MODE TRANSCEIVERHF/VHF/UHF ALL MODE TRANSCEIVER35W output in 70cm bandHigh power MOS-FET amps supply 35W output power on 430/440MHz band as well as 100W on HF/50MHz bands and 50W on 144MHz. It pro-vides stable, high quality output with low IMD and low spurious emissions even during high duty cycle and extended operation.High stability crystal unitThe IC-7000 inco rpo rates a high-stability master o scillato r, pro viding 0.5ppm (–0°C to +50°C). A must for data mode operation.DDS (Direct digital synthesizer) circuitIcom’s original DDS (Direct digital synthesizer) circuit improves the C/N ratio, providing a clear, clean transmit signal in all bands.Compact, all in one packageThe IC-7000 sheds 20mm (0.79 in) of depth compared with the IC-706MKIIG. It’s compact body is easy for carrying outdoors or mobile operation.IF DSP — First in its classDigital IF fi lter, manual no tch fi lter, digital twin PBT and more. The lat-est digital features are incorporated in this compact radio from two DSP chips that deliver superior process-ing perfo rmance. Of co urse, tho se features work on all ham bands, from HF to the 70cm band.AGC loop performance controlled by DSPY ou will never experience AGC pumping from a signal filtered out by the DSP system. The digi-tal IF fi lter and manual notch fi lter are inside the AGC loop, so you will not encounter AGC block-ing. The AGC time constants are fl exibly adjust-able from slow, middle, fast (or AGC-off) for each operating mode.Digital IF fi ltersAll the fi lters you want at your fi ngertips! Y ou will never have to purchase “Optional” filters as the IC-7000 has adjustable digital filters. Y ou just dial in the width you wantand select whether you want a sharp or soft fi lter shape for SSB and CW modes. Then to pull-in the the weak ones, with a quickturn of the concentric twin PBT knobs, you can either narrow the IF passband, or shift the entire passband to eliminate the QRM.2-point MNF (Manual notch fi lter)Pull out the weak signals in crowded band condi-tions with Icom’s NEW two-point MNF (manualnotch fi lter). Apply 70 dB of rejection to two sig-nals at once! Notch width is adjustable – wide, medium, and narrow – and an auto-tuning notch fi lter is available, too.Digital noise reductionNoise reduction reduces background noise and improves signal-to-noise ratio. The noise reduction level is adjustable in 16 steps. It improves the readability of voice and data signals.Digital noise blankerThe noise blanker reduces pulse-type noise such as engine ignition and sparking. The NB level and width (blanking duration) are adjustable in 100 steps.AGC time constant setting Manual notch fi lterIF fi lter settingMOS FET P A unitsIcom original DDS circuitThe technical properties and advantages of IF DSP found in our leading base station models now offers its superior advantages on mobile HF, 50MHz 144MHz and 430/440 MHz bands.2.5 inch color TFT displayThe 2.5 inch color TFT display presents numbers and indicators in bright, concentrated colors for easy recognition. Y ou can choose from 3 back-ground colors and 2 font styles to suit your preference, in addition to a large operating frequency readout. And more, the Video output jack on the rear panel allows you to view a magnifi ed display on an external monitor*.* 3.5(d) mm monaural cable is required for connection.SSB transmit bandwidth adjustableThe SSB transmit bandwidth is selectable from 100, 200, 300, 500Hz atthe high-pass edge, and 2500, 2700, 2800, 2900Hz at the low-pass edgerespectively. 3 types of high and low combinations can be set in the quickset mode.2-mode band scopeThe band scope function lets you watch condi-tions aro und the band and visually assists infi nding other stations. In center mode the bandsco pe range is centered o n the receiving fre-quency (±10kHz to ±250kHz). In Fixed mode theband scope sweeps a fi xed range.Multi function meter and SWR graphic displayThe IC-7000 displays power level, SWR*, ALCand compression level of the speech compres-sor. The SWR graphic display* is useful for tuningantennas. The measuring step is selectable from10/50/100/500kHz steps and the number of mea-suring steps is adjustable from 3 to 13 steps. (* HF/50MHz band only)Other outstanding features• Front panel separation with optional 3.5m/5m separation cable • Selectablemain dial tension from heavy, light and click • RF speech compressor controlledby the DSP • CW full break-in • CW receive reverse • CW pitch adjustable •Tone squelch in FM mode • 503 memory channels • Built-in voice synthesizerannounces operating frequency, mode and signal strength • Duplex mode and au-tomatic repeater function • Transmit monitor • DTMF monitor • 1Hz tuning • VOX• CI-V interface • RIT/∂TX • RF/SQL knob • Large speaker • Auto TS function• Thermo control silent cooling fan • Noise squelch and S-meter squelch• Preamplifi er • Dial lock • 20dB attenuatorEight of the most-used radio func-tions such as NB, NR, MNF, andANF are co ntro lled by dedicatedfunction keys grouped around thedisplay for easy visibility. One quicktouch turns the function on and off.A lo nger to uch activates adjust-ment of the function’s setting.Digital voice recorder (DVR)Record your callsign, CQ, or other information in4 transmit playback memories with alphanumericlabels. A total of 90 seconds is available for thefour memories. A front panel REC control allowsyou to record incoming signals for up to 25 min-utes (99 channels)*. The DVR makes portablecontesting or mini-expeditions a breeze!* Up to 120 seconds per channelBuilt-in RTTY demodulatorThe RTTY demodulator and decoder are built-in.External units and PC are no longer required fordecoding. The twin peak audio fi lter reduces inter-fering signals overlapping the tones and the tuningindicator helps you zero-in with accurate tuning.Remote control microphone, HM-151The HM-151 has a 10-keypad for quick channel selection.The triple band stacking register memorizes the last threefrequencies and modes used on each band. Push the bandbutton once to three times to recall the channel setting. TheF-1 and F-2 buttons are programmable as shortcut menusof your often used functions.Key illuminationVoice RX memoryNegative type Color type Positive typeFixed mode band scopeRTTY decode screenMultimeter screen1-1-32, Kami-minami, Hirano-ku, Osaka 547-0003, Japan Phone: +81 (06) 6793 5302Fax: +81 (06) 6793 0013Count on us!www.icom.co.jp/worldPrinted in Japan2380 116th Avenue NE,Bellevue, WA 98004, U.S.A.Phone : +1 (425) 454-8155Fax : +1 (425) 454-1509E-mail :*********************URL : Unit 1 / 103 Garden Road,Clayton, VIC 3168 Australia Phone : +61 (03) 9549 7500Fax : +61 (03) 9549 7505 E-mail :**************.au URL : .auBlacksole House, Altira Park, Herne Bay, Kent, CT6 6GZ, U.K.Phone : +44 (01227) 741741Fax : +44 (01227) 741742E-mail :**************.ukURL : Zac de la Plaine,1 Rue Brindejonc des Moulinais, BP 45804, 31505 Toulouse Cedex 5, France Phone : +33 (5) 61 36 03 03Fax : +33 (5) 61 36 03 00E-mail :********************URL : Ctra. Rubi, No. 88 "Edificio Can Castanyer" Bajos A 08174, Sant Cugat del Valles, Barcelona, SpainPhone : +34 (93) 590 26 70Fax : +34 (93) 589 04 46E-mail :******************URL : 146A Harris Road, East Tamaki,Auckland, New Zealand Phone : +64 (09) 274 4062Fax : +64 (09) 274 4708E-mail :*****************.nz URL : Glenwood Centre #150-6165 Highway 17,Delta, B.C., V4K 5B8, Canada Phone: +1 (604) 952-4266Fax : +1 (604) 952-0090E-mail :*******************URL: Y our local distributor/dealer:6F No. 68, Sec. 1 Cheng-Teh Road, T aipei, Taiwan, R.O.C.Phone: +886 (02) 2559 1899Fax : +886 (02) 2559 1874E-mail :*******************URL : 81-850 Sopot, ul. 3 Maja 54, Poland Phone : +48 (58) 550 7135Fax : +48 (58) 551 0484E-mail :*************************.pl URL : .plCommunication Equipment Auf der Krautweide 2465812 Bad Soden am Taunus, Germany Phone : +49 (6196) 76685-0Fax : +49 (6196) 76685-50E-mail :*******************URL : HF/VHF/UHF ALL MODE TRANSCEIVER• C T-17 C I-V LEVEL CONVERTERFo r remo te transceiver co ntro l using a PC with an RS-232C.• R S-BA1 I P REMOTE CONTROL SOFTWAREFor IP remote transceiver control from a PC. (Not guaranteed)• Frequency coverage (unit: MHz)*1 :Receive 0.030– 199.999*2 400.000–470.000*2 Transmit 1.800– 1.999 3.500– 3.9995.255– 5.405*2 7.000–7.300 10.100– 10.150 14.000– 14.350 18.068– 18.168 21.000– 21.450 24.890– 24.990 28.000– 29.700 50.000– 54.000 144.000– 148.000430.000– 450.000*1 Showing USA version, frequency coverage depends on version.*2 Some frequency ranges are not guaranteed.• Mode: U SB, LSB, CW, RTTY , AM, FM,WFM (Rx only)• Number of memory Ch. : 503 (495 regular, 6 scan edges and 2 call)• Antenna connector : S O-239×2 (fo r HF/50MHz and 144/430/440MHz bands; 50Ω)• T emperature range : –10˚C to +60˚C; +14˚F to +140˚F • Frequency stability : L ess than ±0.5ppm(0°C to +50°C; +32°F to +122°F)• Power supply requirement : 13.8V DC ±15% • P ower consumption : Tx Max. power 22.0A (approx.) Rx S tandby 1.3AMax. audio 1.6A• D imensions (W×H×D): 167×58×180 mm;(Projections not included) 6.57×2.28×7.09 in• Weight (approx.): 2.3kg; 5.1lb • Modulation system :S SB Digital P .S.N. modulation AM Digital low power modulation FM Digital phase modulation • Spurious emissions : L ess than –50dB (HF bands)Less than –60dB (50MHz band*)Less than –60dB (144/440MHz bands)(* Less than –63dB for EUR versions)• Carrier suppression : More than 50dB • Unwanted sideband suppression: More than 50dB• Microphone connector : 8-pin modular jack (600Ω)• Intermediate frequencies :S SB, CW, RTTY , AM, FM 124.487MHz, 455kHz, 16.15kHz WFM 134.732MHz, 10.70MHz SSB/CW, AM : 10dB S/N, FM, WFM : 12dB SINAD• Squelch sensitivity (Pre-amp: ON, threshold):SSB Less than 5.6μV FM Less than 0.3μV • Selectivity (representative value): S SB More than 2.4kHz/–6dB(BW: 2.4kHz, sharp) Less than 3.6kHz/–60dB C W More than 500Hz/–6dB(BW: 500Hz, sharp) Less than 900Hz/–60dBRTTY(BW: 350Hz) M ore than 360Hz/–6dB Less than 650Hz/–60dBAM(BW: 6kHz) M ore than 6.0kHz/–6dB Less than 15.0kHz/–60dBFM(BW: 15kHz) M ore than 12.0kHz/–6dB Less than 20.0kHz/–60dB• S purious and image : More than 70dB (HF/50MHz bands)rejection ratio More than 65dB (144/440MHz bands)(except 1/2 IF through on 50MHz, IF through on 144MHz)• AF output power : M ore than 2.0W at 10% distortion (at 13.8V DC)with an 8Ω load• EXT SP connector : 2-conductor 3.5 (d) mm (1⁄8ʺ)/8ΩApplicable U.S. Military Specifi cationsSPECIFICATIONSRECEIVERSupplied accessories:• Hand microphone, HM-151 • Microphone hanger • Electronic keyer plug • RTTY key plug • DC power cable • ACC cable (13-pin) • Spare fuses• O PC-599 CABLE ADAPTERCo nverts 13-pin ACC co nnecto r to 7-pin + 8-pin ACC connector forconnection with IC-PW1/EURO.• O PC-742 ACC 13 PIN CABLE ADAPTERRequired when using both AT -180 and a 2 m or 70 cm linear amplifi er.• S EP ARA TION CABLES OPC-1443: 3.5m (11ft)OPC-1444: 5m (16ft)• O PC-589 MODULAR 8-PINCABLE ADAPTER• O PC-598 ACC 13 PIN LONG CABLE FOR A T -180 (7m; 23ft)• M B-106 CARRYING HANDLEOPTIONS• M B-105A MOBILE MOUNT -ING BRACKETFo r mo unting the detached fro nt panel.• M BF-1 MOUNTING BASESuctio n cup mo unting base fo r mo unting the detached fro nt panel. The MB-105A is required.• A H-2b ANTENNA ELEMENTFor mobile operation with the AH-4. All bands between 7–54MHz can be matched.• A H-4 HF+50MHz AUTO-MA TIC ANTENNA TUNERCo vers 3.5–54MHz with a 7m • A T -180 HF+50MHz AUTO-MA TIC ANTENNA TUNERStyle and size are matched to the IC-PW1/IC-PW1EUROHF+50MHz 1kWHF LINEAR AMPLIFIER• H M-151 REMOTE-CONTROL MICROPHONESame as supplied. For exclusive use with IC-7000 only.• S P-10 EXTERNAL SPEAKERHeavy duty speaker fo r mo bile use.• PS-126 DC POWER SUPPL Y13.8V DC, 25A max. with 4-pin type connector.READ ALL INSTRUCTIONS carefully and completely before using the transceiver.All stated specifi cations are subject to change without notice or obligation.Some options may not be available in some countries. Please ask your dealer for details.• S M-30 DESKTOP MICROPHONEElectret microphone.(An optional OPC-589 is required.)SM-20 also can be used with OPC-589.• S M-50 DESKTOP MICROPHONEDynamic microphone.(An optional OPC-589 is required.)• M B-120 MOUNTING BASEFo r mo unting the detached fro nt panel in a vehicle. The MB-105A is required.05ES011K* © 2005–2012 Icom Inc.• M B-62 MOBILE MOUNTING BRACKETFo r mo unting the IC-7000 main unit or the A T -180.Covers all HF and 50MHz bands, provides clean, stable 1kW output.Automatic antenna tuner and compact detachable controller are standard. 2 exciter inputs are available. (An optional OPC-599 is required.)。

❍ 高分辨率的频谱显示器,中心频率和固定频率模式,还有迷 你频谱显示.
❍ 前后面板上的 USB 控制接口. ❍ 大型液晶显示屏采用 LED 背光.
重要
仔细阅读操作说明书
在你尝试操作之前. 如果你发现错误,希望你告知我们及时改正。
保存操作说明书.
本手册包含 IC-7600 重要安全操作说明.
明确定义
文本
• 重新调整或重新定位接收天线 • 增加设备和接收器之间的距离. • 同其他接收器分开连接到电源插座. • 咨询经销商或有经验的无线电/电视技术员的帮助
Icom, Icom Inc. 和 Icom 商标是 ICOM (日本)公司 在日本以及其他地区的注册商标。
注意事项
▣! 警告高射频电压! 禁止 在发射过程中接触
(+122°F)的环境下使用收发器.
切勿 把收发器置于过多灰尘的或者阳光直射的环境
下.
切勿 放置收发器靠近墙壁以及在上面覆盖物体，这
将会使收发器过热.
总是放置在一个安全的地方，以避免儿童意外使 用. 要小心! 如果你使用线性放大器，将收发器的RF 输出 功率不要高于放大器的最大输入电平，否则，线性放 大器将受到毁坏，
随机配件
发射机附带以下附件.
Qty.
○1 手持话筒
........................................................ 1
○2 直流电源线 ............................................................ 1
使用说明书
HF/50 MHz 全模式无线电收发器
IC-7600
手册是参照 IC-7600 的官方英文版手册编译，力求准确反映 原手册内容，手册保持了原版英文排版，涉及专业及水平 有限，失误和疏忽在所难免，手册皆在增加设备交流，仅 供参考此期间产生的一切设备问题概不负责，同样未经许 可你不能用于任何商业目的的使用。编译：BD4UJ

按下发射频率检查开关，窗口上显示出所选用频道的发射频率值。 9、天线调谐器启动按钮 ANTENNA TUNER TUNING SWITCH
当电台与天线调谐器相连接后，按下此开关，给天线调谐器送过去一个启动信号，此时天线调谐指示 灯亮。
等调谐完毕之后，天线调谐指示灯灭，收发信机返回接收状态。 10、 显示开关 DISPLAY SWITCH
在面板窗口左右两边各有一个，取下这两个螺钉，打开窗口，就可以使用数字键盘对存储器编程了。
二、后面板上的连接器
1、 天线插座 输出阻抗为 50Ω，应使用 PL-259 插头。当使用鞭状天线、长天线时，此插座应通过电缆连接至天线
自动调谐器。 2、 接地线
为了防止发生电击，避免其它无线电干扰，请将收发信机通过此端子接地。接地线尽可能使用比较宽 的铜带，接地线尽可能地短一些。 3、 外接扬声器插座
在 4Ω负载上，失真度为 10%时，输出功率不小于 5W。 8、 输出阻抗
2 ~ 8Ω 第二节、特征
1、 48 个存储频道 IC-M700 收发信机的频率范围覆盖了船岸通信、远洋电话、和船舶之间通信的所有频率，可以使用单
工、半双工方式工作，可以灵活地以 100Hz 的步进频率为收发频率单独编程。 本机具有频率合成系统，可以通过前面板上的键盘进行编程并且存储下来。
设置所需要的工作方式 A3J、A3A、A3H。 IC-M700 在出厂时，已经存入常用的海洋通信频率。
三、频道的重新编程
当需要使用其它频率时，应对频道重新编程。 （1）用波道组开关任选 A、B、C、D 中的任何一个波道，再用频道开关任意选择 1～16 个频道中的一个。 如果原频道没有存储频率，则面板上的频率显示器上只有 MHz 和 kHz 位上由小数点在闪亮。 （2）拆掉频率显示器窗口两边的螺丝，卸下窗盖，露出键盘。 （3）首先预置接收频率，看准键盘上所标注的 0～9 的数字键。把所需要频率的 6 位数字（最低位是百 Hz 位），从最高位至最低位的顺序依次按压数字键，此时显示屏幕上显示出的数字就是所设置的频率值。 如果输入出现了错误，可按一下复位键 CE，则输入的频率被删除而恢复到初始状态，然后重新输入。

注意
△！ 危險！禁止把收發兩用機直接接到交流電㆖。這樣會引起火焰或導致電擊。 △！ 危險！禁止把收發兩用機安放在高於頭部的㆞方。此收發兩用機重約 8 公斤， 而且由於電波的沖擊和振動，將使其產生幾倍於其重量的力。必須把收發兩用 機安裝在平整的硬平面㆖。 禁止（直接）使用超過 16V 的直流電源，例如 24V 的直流電池。若（直接）接 到超過 16V 的直流電源㆖會燒壞儀器。 禁止兒童接觸此儀器，包括無線電發射機。 禁止淋㆖雨、雪，或浸㆖其他液體。 禁止 IC-M700PRO 接到正接㆞船㆖。這樣會導致保險絲燒壞而不能使用。 請勿用苯類，酒精等化學試劑擦拭儀器，這樣會損壞收發兩用機的表面。 用於船㆖時，請儘可能使收發兩用機和麥克風離磁性導向羅盤儀遠㆒些（至少 要 1 米以㆖），以防止出現不正確的顯示。 本品只能使用 ICOM 制的麥克風和手機（附帶或選）。 如使用其他廠商的產品，其針腳排列可能與本品不同，可能會導致儀器損壞。 避免在溫度低於-20 攝氏度獲高於+60 攝氏度的場合使用或放置。 請勿把收發兩用機的電源性接反（正負極和電源接反）。這樣連接不僅要燒壞保 險絲，而且還有可能燒毀收發兩用機。 避免雙重污染（弄髒）該儀器或把儀器曝曬於陽光之㆘。 請勿靠牆放置，請勿在收發兩用機㆖放置任何東西，這樣會影響其散熱。
該收發兩用機配有 150 個頻道，被分成 3 組，每組有 50 個頻道（最大為 50）。 而且，每組的頻道數還可以根據您的需 要加以限制。（詳見第 13、14 頁） &注：當用﹝2182kHz﹞開關來選擇 0 頻道或 2182kHz 頻道時，需先按㆘ ﹝2182kHz﹞按鈕，否則選擇不了頻道。 M如需要，可按﹝CH/FREQ﹞按鈕選擇 記憶模式頻道。 N先用旋轉按鈕﹝GROUP﹞選擇所需 頻道組，然後再旋轉旋鈕 ﹝CHANNEL﹞來選擇所需頻道。

ICOM IC-R7000使用说明书一、主要旋钮、按键及开关说明1、速度钮SPEED，用于扫描速度的调整，右旋到底扫描速度最大。

2、延时方式钮DELAY，用于扫描过程中检测到信号时停留延时方式。

OFF‐信号出现多久就暂停多久；5‐停留5秒钟；15‐停留15秒钟；∞‐只要检测到信号就停止扫描。

3、扫描键盘SCAN START/STOP，可设置六种扫描方式：重点扫描、频段扫描、选择信道扫描、同种制式扫描、所有信道扫描和自动扫描存贮。

①、重点扫描键PRIO，可在当前信道频率和重点设置的频率这两个频率间进行扫描。

②、频段扫描键PROG，设置了低频和高频后，则以TS旋钮设置的步进反复进行扫描。

③、选择信道扫描键SEL‐M，在选择了的各个信道中进行扫描。

④、同种制式信道扫描键MODE，扫描与当前制式相同的各个信道。

⑤、所有信道扫描键MEMORY，扫描所有的存贮了的信道。

⑥、自动扫描存贮键AUTO‐M，根据频段扫描中设置的高低频率，扫描并自动存贮到CH80~99信道中，因此CH80~99信道不作为常规存贮信道用。

4、衰减键ATT，天线衰减器，按下为衰减。

实际工作中一般不需衰减，不用按下此键。

5、频段键1GHz，按下此键则转换到1GHz以上的频段，最高监测频率可达1999.999MHz。

6、锁键LOCK，锁定键。

7、信道钮MEMORY CH，选择信道旋钮。

8、存写键WRITE，将频率存写入信道。

9、清除键CLEAR，清除当前信道内的频率数据。

10、确定键ENT，输入频率及其调制方式时的确定键。

11、步进钮TS(kHz)，频率步进钮，频段扫描时用，一般设为25 kHz。

12、音量钮AF GAIN，旋至合适位置即可。

13、静噪钮SQUELCH，扫描时要旋至合适位置。

14、FM频段开关（在背面），对FM和FMn调制方式有影响，因此要根据实际情况将此开关拨至FM(1)或FM(2)档位，才能正常监听FM或FMn的信号。

二、存写信道。