美标检测标准模板

Metal Works Detailing StandardTYP Mark Number:∙Mark all assemblies starting with A.∙所有的构件号以“A”为字首∙Mark all single piece part starting with T.∙所有的零件号以“T”为字首Steel Erection Drawing (always in 24”x36” size paper)安装图图框总是24”x36”∙Provide 3D views with assembly mark numbers, need at least two 3D views looking from southwest and northeast corners so that the structural members can be visualized clearly.∙最少两个三维视图，从西南与东北两个角度，显示所有的构件编号∙Provide anchor bolt plan with column mark number and column size, show anchor bolt template mark numbers, anchor bolt mark number and diameter.There are TYP 4 anchor bolt at each column, only need to show one of the anchor bolt as AB1 Dia1” A.bolt at each column location, for example.∙锚栓布置图：柱子编号，柱截面，锚栓模版编号，锚栓编号和直径，如果一个柱子有四个相同的锚栓仅仅标明一个锚栓就行了。

∙Provide anchor bolt enlarged details (usually at 1:12 scale), show plan view and section view of anchor bolt setting. Show anchor bolt template mark and anchor bolt mark & diameter. Need to give dimension to the grout thickness, anchor projection length from top of footing, anchor bolt spacing from center line of column.∙提供锚栓大样图，通常以一比十二的比例，柱脚锚栓的平面与剖面图，锚栓模版与锚栓编号和锚栓直径，标出二次灌桨层厚度，锚栓超出基础的投影长度，锚栓与柱中心线的间距∙Provide floor framing plan and roof framing plan with beam mark numbers and sizes, if there is camber in beam, need to show the camber too. Don’t need to show orientation mark. Give an enlarged plan detail showing the TYP connection plate side in relation to the beam web, for example, TYP the shear connection plate is at north side or east side of the beam web, and add a note like this at the TYP detail.∙楼面梁与屋面梁：梁编号，梁截面，如果有起拱还要标明起拱。

前言GM给生产件供应商的检具标准是为了建立GM供应商PPAP检具全球性的公用标准而开发的。

先前，GM各部门及单位有其各自的检具标准。

1996年，来自GM卡车集团、中等/豪华及小型汽车集团的代表成立了一个开发小组。

另外，在开发过程中，我门还得到了Saturn、GM动力总成和GM加拿大集团的合作。

译注：本标准的中文版是由上海通用汽车有限公司，物料管理部，供应商开发/供应商质量科翻译。

如译文与英文原文 有冲突处，以英文原文为准。

1998年6月2日目录标题页次更改信息 3 I.序言 4 II.零件供应商的责任 5 III.设计概念 6 IV.概念批准7 V.设计要求7 VI.制造要求9 VII.认证要求12 VIII.量具重复性和再现性的要求 13 IX.保养要求15 X.术语15 XI.附录A 16 XII.附录B 17更改信息版本日期段落条目 12/97 发布1.0本标准中如发生任何更改都将记录在本页中。

当发生新的更改时，在保留本页清单原有记录的基础上，再增加新的更改内容。

修订后的版本将以版本1.0、2.0、3.0的顺序发布。

当不同的版本发布时，通过参照段落和条目的相应内容，可迅速找出更改内容。

本文件替代下列文件：*卡车和客车检具/量具标准（T& B 391）、12月、1989。

*中等/豪华汽车集团检具设计/制造标准，4月，1996。

I.序言A.介绍依照汽车工业行动集团（AIAG），先期产品质量策划手册和生产件批准程序的要求，每当需要时，零件供应商应按照他们的质量计划获取检具来检验他们的产品。

生产件供应商在对GM的零件的检具进行报价、设计和制造时，除了使用他们自己的标准和要求外，还要参照本手册。

如果GM的供应商质量工程师（SQE）认为确有必要，可根据检测条件来修改此标准，但只在有相应的支持文件时才能修改（译注：如经EWO程序）。

B.适用范围GM检具标准概括了全球范围所有GM供应商PPAP检具的最低要求。

美国ASTM标准标准号中文名称英文名称A1-00碳素钢丁字轨Standard Specification for Carbon Steel Tee RailsA2-02普通型,带槽和防护型碳素工字钢轨Standard Specification for Carbon Steel Girder Rails of Plain, Grooved, and Guard TypesA3-01低、中、高碳素钢鱼尾（连接）板Standard Specification for Steel Joint Bars, Low, Medium, and High Carbon (Non-Heat-Treated)A6/A6M-04a轧制结构钢板材、型材和薄板桩通用技术要求Standard Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling A20/A20M-04a压力容器用钢板材通用要求Standard Specification for General Requirements for Steel Plates for Pressure VesselsA27/A27M-03通用碳素钢铸件Standard Specification for Steel Castings, Carbon, for General ApplicationA29/A29M-04热锻及冷加工碳素钢和合金钢棒Standard Specification for Steel Bars, Carbon and Alloy, Hot-Wrought, General Requirements forA31-04钢铆钉及铆钉和压力容器用棒材Standard Specification for Steel Rivets and Bars for Rivets, Pressure VesselsA34/A34M-01磁性材料的抽样和采购试验的标准惯例Standard Practice for Sampling and Procurement Testing of Magnetic MaterialsA36/A36M-04碳素结构钢技术规范Standard Specification for Carbon Structural SteelA47/A47M-99铁素体可锻铁铸件Standard Specification forFerritic Malleable Iron Castings A48/A48M-03灰铁铸件Standard Specification for Gray Iron CastingsA49-01经热处理的碳素钢鱼尾（连接）板，微合金鱼尾板及锻制碳素钢异型鱼尾板Standard Specification for Heat-Treated Carbon Steel Joint Bars,Microalloyed Joint Bars, and Forged Carbon Steel Compromise Joint BarsA53/A53M-04无镀层热浸的、镀锌的、焊接的及无缝钢管的技术规范Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and SeamlessA65-01钢轨道钉Standard Specification for Steel Track Spikes A66-01钢质螺旋道钉Standard Specification for Steel Screw Spikes A67-00热加工低碳钢和高碳钢垫板技术规范Standard Specification for Steel Tie Plates, Low-Carbon and High-Carbon Hot-WorkedA74-04铸铁污水管及配件的技术规范Standard Specification for Cast Iron Soil Pipe and FittingsA82-02钢筋混凝土用无节钢丝Standard Specification for Steel Wire, Plain, for Concrete ReinforcementA90/A90M-01镀锌和镀锌合金钢铁制品镀层重量的试验方法Standard Test Method for Weight [Mass] of Coating on Iron and Steel Articles with Zinc or Zinc-Alloy CoatingsA99-03锰铁合金Standard Specification for Ferromanganese A100-04硅铁Standard Specification for FerrosiliconA101-04铬铁Standard Specification for FerrochromiumA102-04钒铁合金Standard Specification for Ferrovanadium A105/A105M-03管系部件用碳素钢锻件Standard Specification for Carbon Steel Forgings for Piping ApplicationsA106/A106M-04a高温用无缝碳素钢管Standard Specification for Seamless Carbon Steel Pipe for High-Temperature Service A108-03优质冷加工碳素钢棒材技术规范Standard Specification for Steel Bar, Carbon and Alloy, Cold-Finished A109/A109M-03冷轧碳素钢带技术规范Standard Specification for Steel, Strip, Carbon (0.25 Maximum Percent), Cold-RolledA111-99a(2004)e1电话和电报线路用镀锌"铁"丝规格Standard Specification for Zinc-Coated (Galvanized) Iron Telephone and Telegraph Line WireA116-00镀锌钢丝编织栏栅网Standard Specification for Metallic-Coated, Steel Woven Wire Fence Fabric A121-99(2004)镀锌刺钢丝Standard Specification for Mettalic-Coated Carbon Steel Barbed WireA123/A123M-02钢铁产品的锌镀层（热浸镀锌）技术规范Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel ProductsA125-96(2001)热处理螺旋形钢弹簧Standard Specification for Steel Springs, Helical, Heat-TreatedA126-04阀门、法兰和管配件用灰铁铸件Standard Specification for Gray Iron Castings for Valves, Flanges, and Pipe FittingsA128/A128M-93(2003)钢铸件,奥氏体锰Standard Specification for Steel Castings, Austenitic Manganese A131/A131M-04海船用结构钢Standard Specification for Structural Steel for ShipsA132-04钼铁合金Standard Specification for FerromolybdenumA134-96(2001)电熔(电弧)焊钢管(NPS为16英寸和16英寸以上)Standard Specification for Pipe, Steel, Electric-Fusion (Arc)-Welded (Sizes NPS 16 and Over)A135-01电阻焊钢管Standard Specification for Electric-Resistance-Welded Steel PipeA139/A139M-04电熔(电弧)焊钢管(4英寸以上的)Standard Specification for Electric-Fusion (Arc)-Welded Steel Pipe (NPS 4 and Over)A143/A143M-03热浸镀锌结构钢制品防脆裂措施和探测脆裂的程序Standard Practice for Safeguarding Against Embrittlement of Hot-Dip Galvanized Structural Steel Products and Procedure for Detecting EmbrittlementA144-02铁钨合金规范Specification for FerrotungstenA146-04氧化钼制品Standard Specification for Molybdenum Oxide ProductsA148/A148M-03结构用高强度钢铸件Standard Specification for Steel Castings, High Strength, for Structural Purposes A153/A153M-04钢铁制金属构件上镀锌层(热浸)Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel HardwareA159-83(2001)汽车用灰铁铸件Standard Specification for Automotive Gray Iron CastingsA167-99不锈钢和耐热铬镍钢板、薄板及带材Standard Specification for Stainless and Heat-Resisting Chromium-Nickel Steel Plate, Sheet, and StripA176-99不锈钢和耐热铬钢板、薄板及带材Standard Specification for Stainless and Heat-Resisting Chromium Steel Plate, Sheet, and StripA178/A178M-02电阻焊接碳素钢钢管及碳锰钢锅炉和过热器管的技术规范Standard Specification for Electric-Resistance-Welded Carbon Steel and Carbon-Manganese Steel Boiler and Superheater TubesA179/A179M-90a(2001)热交换器和冷凝器用无缝冷拉低碳钢管Standard Specification for Seamless Cold-Drawn Low-Carbon Steel Heat-Exchanger and Condenser TubesA181/A181M-01普通锻制碳素钢管的规格Standard Specification for Carbon Steel Forgings, for General-Purpose PipingA182/A182M-02高温设备用锻制或轧制的合金钢管法兰、锻制管件、阀门及零件Standard Specification for Forged or Rolled Alloy-Steel Pipe Flanges,Forged Fittings, and Valves and Parts for High-Temperature ServiceA183-03钢轨用碳素钢螺栓和螺母Standard Specification for Carbon Steel Track Bolts and NutsA184/A184M-01混凝土加筋用变形钢筋编织网Standard Specification for Fabricated Deformed Steel Bar Mats for Concrete ReinforcementA185-02钢筋混凝土用焊接钢丝结构Standard Specification for Steel Welded Wire Reinforcement, Plain, for Concrete A192/A192M-02高压用无缝碳素钢锅炉管Standard Specification for Seamless Carbon Steel Boiler Tubes for High-Pressure ServiceA193/A193M-04b高温设备用合金钢和不锈钢螺栓材料Standard Specification for Alloy-Steel and Stainless Steel Bolting Materials for High-Temperature ServiceA194/A194M-04a高温和高压设备用碳素钢与合金钢螺栓和螺母的规格Standard Specification for Carbon and Alloy Steel Nuts for Bolts for High Pressure or High Temperature Service, or Both A197/A197M-00化铁炉用可锻铸铁Standard Specification forCupola Malleable IronA202/A202M-03压力容器用铬锰硅合金钢板Standard Specification for Pressure Vessel Plates, Alloy Steel, Chromium-Manganese-SiliconA203/A203M-97(2003)压力容器用镍合金钢板Standard Specification for Pressure Vessel Plates, Alloy Steel, Nickel A204/A204M-03压力容器用钼合金钢板Standard Specification for Pressure Vessel Plates, Alloy Steel, Molybdenum A209/A209M-03锅炉和过热器用无缝碳钼合金钢管Standard Specification for Seamless Carbon-Molybdenum Alloy-Steel Boiler and Superheater TubesA210/A210M-02锅炉和过热器用无缝中碳素管Standard Specification for Seamless Medium-Carbon Steel Boiler and Superheater TubesA213/A213M-04无缝铁素体和奥氏体合金钢锅炉、过热器和换热器管Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger Tubes A214/A214M-96(2001)热交换器与冷凝器用电阻焊接碳素钢管Standard Specification for Electric-Resistance-Welded Carbon Steel Heat-Exchanger and Condenser TubesA216/A216M-93(2003)高温下使用的适合于熔焊的碳素钢铸件规格Standard Specification for Steel Castings, Carbon, Suitable for Fusion Welding, for High- Temperature ServiceA217/A217M-02适合高温受压零件用合金钢和马氏体不锈钢铸件Standard Specification for Steel Castings, Martensitic Stainless and Alloy, for Pressure-Containing Parts, Suitable for High-Temperature ServiceA220/A220M-99珠光体可锻铁Standard Specification for Pearlitic Malleable IronA225/A225M-03压力容器用锰矾镍合金钢板StandardSpecification for Pressure Vessel Plates, Alloy Steel, Manganese-Vanadium-NickelA227/A227M-99机械弹簧用冷拉钢丝Standard Specification for Steel Wire, Cold-Drawn for Mechanical Springs A228/A228M-02乐器用优质弹簧钢丝Standard Specification for Steel Wire, Music Spring QualityA229/A229M-99机械弹簧用油回火的钢丝Standard Specification for Steel Wire, Oil-Tempered for Mechanical Springs A230/A230M-99阀门用油回火优质碳素钢弹簧丝Standard Specification for Steel Wire, Oil-Tempered Carbon Valve Spring QualityA231/A231M-96(2002)铬钒合金钢弹簧丝Standard Specification for Chromium-Vanadium Alloy Steel Spring Wire A232/A232M-99阀门用优质铬钒合金钢弹簧丝Standard Specification for Chromium-Vanadium Alloy Steel Valve Spring Quality WireA234/A234M-04中温与高温下使用的锻制碳素钢及合金钢管配件Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Moderate and High Temperature Service A239-95(2004)用普力斯试验法(硫酸铜浸蚀)确定铁或钢制品上镀锌层最薄点的测试方法Standard Practice for Locating the Thinnest Spot in a Zinc (Galvanized)Coating on Iron or Steel ArticlesA240/A240M-04ae1压力容器用耐热铬及铬镍不锈钢板、薄板及带材Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General ApplicationsA242/A242M-04高强度低合金结构钢Standard Specificationfor High-Strength Low-Alloy Structural SteelA247-67(1998)铁铸件中石墨显微结构评定试验方法Standard Test Method for Evaluating the Microstructure of Graphite in Iron CastingsA249/A249M-04锅炉、过热器、换热器和冷凝器用焊接奥氏体钢管Standard Specification for Welded Austenitic Steel Boiler, Superheater, Heat-Exchanger, and Condenser TubesA250/A250M-04锅炉和过热器用电阻焊铁素体合金钢管Standard Specification for Electric-Resistance-Welded Ferritic Alloy-Steel Boiler and Superheater TubesA252-98(2002)焊接钢和无缝钢管桩Standard Specification for Welded and Seamless Steel Pipe Piles A254-97(2002)铜焊钢管规格Standard Specification for Copper-Brazed Steel Tubing A255-02测定钢淬透性用末端淬火试验的标准试验方法Standard Test Method for Determining Hardenability of SteelA262-03奥氏体不锈钢晶间浸蚀敏感性的检测Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless SteelsA263-03耐腐蚀铬钢包覆板材,薄板材及带材技术规范Standard Specification for Stainless Chromium Steel-Clad Plate A264-03包覆的不锈铬镍钢板,薄板及带材规格Specification for Stainless Chromium-Nickel Steel-Clad PlateA265-03镍和镍基合金包覆钢板规格Standard Specification for Nickel and Nickel-Base Alloy-Clad Steel PlateA266/A266M-03a压力容器部件用碳素钢锻件规格Standard Specification for Carbon Steel Forgings for Pressure Vessel ComponentsA268/A268M-04一般设备用无缝和焊接铁素体与马氏体不锈钢管Standard Specification for Seamless and Welded Ferritic and Martensitic Stainless Steel Tubing for General ServiceA269-04一般设备用无缝和焊接奥氏体不锈钢管Standard Specification for Seamless and Welded Austenitic Stainless Steel Tubing for General ServiceA270-03a卫生设施用无缝钢和焊接奥氏体不锈钢管Standard Specification for Seamless and Welded Austenitic Stainless Steel Sanitary TubingA275/A275M-98(2003)钢锻件的磁粉检查试验方法Standard Test Method for Magnetic Particle Examination of Steel Forgings A276-04不锈钢棒材和型材Standard Specification for Stainless Steel Bars and ShapesA278/A278M-01适用于650F容压部件用灰铸铁件的技术规范Standard Specification for Gray Iron Castings for Pressure-Containing Parts for Temperatures Up to 650°F (350°C) A283/A283M-03低和中等抗拉强度碳素钢板Standard Specification for Low and Intermediate Tensile Strength Carbon Steel PlatesA285/A285M-03压力容器用低和中等抗拉强度的碳素钢板Intermediate-Tensile StrengthA288-91(2003)涡轮发电机磁性定位环用碳素钢和合金钢锻件Standard Specification for Carbon and Alloy Steel Forgings for Magnetic Retaining Rings for Turbine GeneratorsA289/A289M-97(2003)发电机非磁性定位环用合金钢锻件的技术规范Standard Specification for Alloy Steel Forgings for Nonmagnetic Retaining Rings for GeneratorsA290-02减速器环用碳素钢和合金钢锻件Standard Specification for Carbon and Alloy Steel Forgings for Rings for Reduction GearsA291-03减速器小齿轮、齿轮和心轴用碳素钢和合金钢锻件Standard Specification for Steel Forgings, Carbon and Alloy, for Pinions, Gears and Shafts for Reduction GearsA295-98高碳耐磨轴承钢技术规范Standard Specification for High-Carbon Anti-Friction Bearing SteelA297/A297M-97(2003)一般用耐热铬铁与镍铬铁合金钢铸件规格Standard Specification for Steel Castings, Iron-Chromium and Iron-Chromium-Nickel, Heat Resistant, for General Application A299/A299M-04压力容器用锰硅碳钢板Standard Specification for Pressure Vessel Plates, Carbon Steel, Manganese-SiliconA302/A302M-03压力容器用锰钼和锰钼镍合金钢板Standard Specification for Pressure Vessel Plates, Alloy Steel, Manganese-Molybdenum and Manganese-Molybdenum-NickelA304-04有末端淬火淬透性要求的合金钢棒材的技术规范Standard Specification for Carbon and Alloy Steel Bars Subject to End-Quench Hardenability RequirementsA307-04抗拉强度为60000psi的碳素钢螺栓和螺柱的技术规范Standard Specification for Carbon Steel Bolts and Studs, 60 000 PSI Tensile StrengthA308/A308M-03经热浸处理镀有铅锡合金的薄板材的技术规范Standard Specification for Steel Sheet, Terne (Lead-Tin Alloy) Coated by the Hot-Dip ProcessA309-01用三点试验法测定长镀锌薄钢板镀层的重量成分的试验方法Standard Test Method for Weight and Composition of Coating on Terne Sheet by the Triple-Spot TestA311/A311M-04有机械性能要求的消除应力的冷拉碳素钢棒Standard Specification for Cold-Drawn, Stress-Relieved Carbon Steel Bars Subject to Mechanical Property Requirements A312/A312M-04a无缝和焊接奥氏体不锈钢管Standard Specification for Seamless, Welded, and Heavily Cold Worked Austenitic Stainless Steel PipesA313/A313M-03不锈钢弹簧丝技术规范StandardSpecification for Stainless Steel Spring WireA314-97(2002)锻造用不锈及耐热钢坯及钢棒规格Standard Specification for Stainless Steel Billets and Bars for Forging A319-71(2001)高温无压部件用灰铁铸件Standard Specification for Gray Iron Castings for Elevated Temperatures for Non-Pressure Containing PartsA320/A320M-04低温用合金钢螺栓材料规格Standard Specification for Alloy-Steel and Stainless Steel Bolting Materials for Low-T emperature ServiceA321-90(2001)经淬火和回火的碳素钢棒Standard Specification for Steel Bars, Carbon, Quenched and T empered A322-91(2001)e1合金钢棒材.级别Standard Specification for Steel Bars, Alloy, Standard GradesA323-93(2000)硼铁规格Standard Specification for FerroboronA324-73(2000)钛铁合金Standard Specification for FerrotitaniumA325-04a经热处理最小抗拉强度为120/105ksi的热处理钢结构螺栓Standard Specification for Structural Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile StrengthA325M-04a经热处理最小抗拉强度为830Mpa的热处理钢结构螺栓Minimum Tensile Strength [Metric]A327-91(1997)铸铁冲击试验方法Standard Test Methods for Impact Testing of Cast IronsA327M-91(1997)铸铁冲击试验方法(米制)Standard Test Methods for Impact Testing of Cast Irons (Metric) A328/A328M-03薄钢板桩Standard Specification for Steel Sheet Piling A333/A333M-04a低温用无缝与焊接钢管规格Standard Specification for Seamless and Welded Steel Pipe for Low-Temperature ServiceA334/A334M-04a低温设备用无缝与焊接碳素和合金钢管Standard Specification for Seamless and Welded Carbon and Alloy-Steel Tubes for Low-T emperature ServiceA335/A335M-03高温用无缝铁素体合金钢管Standard Specification for Seamless Ferritic Alloy-Steel Pipe for High-Temperature ServiceA336/A336M-03a压力与高温部件用合金钢锻件规格Standard Specification for Alloy Steel Forgings for Pressure and High-Temperature PartsA338-84(2004)铁路,船舶和其他重型装备在温度达到650华氏度(345摄氏度)时使用的可锻铸铁法兰,管件和阀门零件Standard Specification for Malleable Iron Flanges, Pipe Fittings, andValve Parts for Railroad, Marine, and Other Heavy Duty Service atTemperatures Up to 650°F (345°C)A340-03a有关磁性试验用符号和定义的术语Standard Terminology of Symbols and Definitions Relating to Magnetic TestingA341/A341M-00用直流磁导计和冲击试验法测定材料的直流磁性能的试验方法Standard Test Method for Direct Current Magnetic Properties of MaterialsUsing D-C Permeameters and the Ballistic Test MethodsA342/A342M-99磁铁材料导磁率的试验方法Standard Test Methods for Permeability of Feebly Magnetic Materials A343/A343M-03在电力频率下用瓦特计-安培计-伏特计法(100-1000赫兹)和25 厘米艾普斯亭(EPSTEIN) 机架测定材料的交流电磁性能的试验方法Standard Test Method for Alternating-Current Magnetic Properties ofMaterials at Power Frequencies Using Wattmeter-Ammeter-Voltmeter Methodand 25-cm Epstein Test FrameA345-98磁设备用平轧电炉钢Standard Specification for Flat-Rolled Electrical Steels for Magnetic ApplicationsA348/A348M-00用瓦特计--安培计--伏特计法(100-10000赫兹)和25厘米艾普斯亭框测定材料的交流磁性能的试验方法Standard Test Method for Alternating Current Magnetic Properties ofMaterials Using the Wattmeter-Ammeter-Voltmeter Method, 100 to 10 000 Hzand 25-cm Epstein FrameA350/A350M-04要求进行缺口韧性试验的管道部件用碳素钢与低合金钢锻件技术规范Standard Specification for Carbon and Low-Alloy Steel Forgings, RequiringNotch Toughness T esting for Piping ComponentsA351/A351M-03容压零件用奥氏体及奥氏体铁素体铸铁的技术规范Standard Specification for Castings, Austenitic, Austenitic-Ferritic (Duplex), for Pressure-Containing PartsA352/A352M-03低温受压零件用铁素体和马氏体钢铸件规格Standard Specification for Steel Castings, Ferritic and Martensitic, for Pressure-Containing Parts, Suitable for Low-Temperature ServiceA353/A353M-93(1999)压力容器用经二次正火及回火处理的含9％镍的合金钢板Standard Specification for Pressure Vessel Plates, Alloy Steel, 9 Percent Nickel, Double-Normalized and Tempered A354-04淬火与回火合金钢螺栓,双头螺栓及其他外螺纹紧固件规格Standard Specification for Quenched and Tempered Alloy Steel Bolts, Studs, and Other Externally Threaded FastenersA355-89(2000)渗氮用合金钢棒Standard Specification for Steel Bars, Alloys, for NitridingStandard Specification for Steel Castings, Carbon, Low Alloy, andA356/A356M-98(2003)蒸汽轮机用厚壁碳素钢、低合金钢和不锈钢铸件Stainless Steel, Heavy-Walled for Steam Turbines A358/A358M-04高温用电熔焊奥氏体铬镍合金钢管Standard Specification for Electric-Fusion-Welded Austenitic Chromium-Nickel Stainless Steel Pipe for High-Temperature Service and General ApplicationsA363-03地面架空线用镀锌钢丝绳Standard Specification for Zinc-Coated (Galvanized) Steel Overhead Ground Wire Strand A367-60(1999)铸铁的激冷试验方法Standard Test Methods of Chill Testing of Cast IronA368-95a(2000)不锈钢和耐热钢丝绳的标准Standard Specification for Stainless Steel Wire StrandA369/A369M-02高温用锻制和镗孔碳素钢管和铁素体合金钢管Standard Specification for Carbon and Ferritic Alloy Steel Forged and Bored Pipe for High-Temperature ServiceA370-03a钢制品机械测试的标准试验方法和定义Standard Test Methods and Definitions for Mechanical Testing of Steel Products A372/A372M-03薄壁压力容器用碳素钢及合金钢锻件Standard Specification for Carbon and Alloy Steel Forgings for Thin-Walled Pressure VesselsA376/A376M-02a高温中心站用无缝奥氏钢管Standard Specification for Seamless Austenitic Steel Pipe for High-Temperature Central-Station ServiceA377-03球墨铸铁压力管规范索引Standard Index of Specifications for Ductile-Iron Pressure PipeA380-99e1不锈钢零件、设备和系统的清洗和除垢Standard Practice for Cleaning, Descaling, and Passivation of Stainless Steel Parts, Equipment, and SystemsA381-96(2001)高压输送用金属弧焊钢管Standard Specification for Metal-Arc-Welded Steel Pipe for Use With High-Pressure Transmission SystemsA384/A384M-02防止钢组件热浸镀锌时翘曲和扭曲用安全保护Standard Practice for Safeguarding Against Warpage and Distortion During Hot-Dip Galvanizing of Steel Assemblies A385-03提供高质量镀锌覆层(热浸)Standard Practice for Providing High-Quality Zinc Coatings (Hot-Dip)A387/A387M-03压力容器用铬钼合金钢板Standard Specification for Pressure Vessel Plates, Alloy Steel, Chromium-MolybdenumA388/A388M-03重型钢锻件超声波检测Standard Practice for Ultrasonic Examination of Heavy Steel ForgingsA389/A389M-03适合高温受压部件用经特殊热处理的合金钢铸件规格Standard Specification for Steel Castings, Alloy, Specially Heat-Treated, for Pressure-Containing Parts, Suitable for High-Temperature ServiceA390-95(2001)饲养家禽用镀锌钢丝栏栅网(六角形和直线形)Standard Specification for Zinc-Coated (Galvanized) Steel Poultry Fence Fabric (Hexagonal and Straight Line)A391/A391M-0180号合金钢链条Standard Specification for Grade 80 Alloy Steel ChainA392-03镀锌钢丝链环栏栅网Standard Specification for Zinc-Coated Steel Chain-Link Fence FabricA394-04传动塔架用镀锌和裸露钢螺栓Standard Specification for Steel Transmission Tower Bolts, Zinc-Coated and Bare A395/A395M-99e1高温用铁素体球墨铸铁受压铸件Standard Specification for Ferritic Ductile Iron Pressure-Retaining Castings for Use at Elevated TemperaturesA400-69(2000)钢棒的成分及机械性能选择指南Standard Practice for Steel Bars, Selection Guide, Composition, and Mechanical PropertiesA401/A401M-03铬硅合金钢丝Standard Specification for Steel Wire, Chromium-Silicon AlloyA403/A403M-04锻制奥氏体不锈钢管配件Standard Specification for Wrought Austenitic Stainless Steel Piping FittingsA407-93(2004)盘簧用冷拉钢丝Standard Specification for Steel Wire, Cold-Drawn, for Coiled-Type SpringsA409/A409M-01腐蚀场所或高温下使用的焊接大口径奥氏体钢管Standard Specification for Welded Large Diameter Austenitic Steel Pipe for Corrosive or High-T emperature Service A411-03镀锌低碳钢铠装线Standard Specification for Zinc-Coated (Galvanized) Low-Carbon Steel Armor WireA413/A413M-01碳素钢链Standard Specification for Carbon Steel ChainA414/A414M-04压力容器用碳素薄钢板Standard Specification for Steel, Sheet, Carbon, for Pressure Vessels A416/A416M-02预应力混凝土用无涂层七股钢铰线Standard Specification for Steel Strand, Uncoated Seven-Wire for Prestressed ConcreteA417-93(2004)之字形、方形、正弦形家具用弹簧元件用冷拔钢丝Standard Specification for Steel Wire, Cold-Drawn, for Zig-Zag, Square-Formed, and Sinuous-Type Upholstery Spring Units A418-99(2003)涡轮机及发电机钢转子锻件的超声波检查方法Standard Test Method for Ultrasonic Examination of Turbine and Generator Steel Rotor ForgingsA420/A420M-04低温下用锻制碳素钢和合金钢管配件Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Low-Temperature ServiceA421/A421M-02预应力混凝土用无涂层消除应力钢丝的技术规范Standard Specification for Uncoated Stress-Relieved Steel Wire for Prestressed ConcreteA423/A423M-95(2000)无缝和电焊低合金钢管Standard Specification for Seamless and Electric-Welded Low-Alloy Steel TubesA424-00搪瓷用钢薄板Standard Specification for Steel, Sheet, for Porcelain EnamelingA426/A426M-02高温用离心铸造的铁素体合金钢管Standard Specification for Centrifugally Cast Ferritic Alloy Steel Pipe for High-Temperature ServiceA427-02冷轧和热轧用锻制合金钢辊Standard Specification for Wrought Alloy Steel Rolls for Cold and Hot Reduction A428/A428M-01钢铁制品上铝覆层重量的测试方法Standard Test Method for Weight [Mass] of Coating on Aluminum-Coated Iron or Steel ArticlesA434-04热轧与冷精轧经回火及淬火的合金钢棒Standard Specification for Steel Bars, Alloy, Hot-Wrought or Cold-Finished, Quenched and TemperedA435/A435M-90(2001)钢板的直射束纵向超声波检验Standard Specification for Straight-Beam Ultrasonic Examination of Steel PlatesA436-84(2001)奥氏体灰口铁铸件Standard Specification for Austenitic Gray Iron CastingsA437/A437M-01a高温用经特殊处理的涡轮型合金钢螺栓材料Standard Specification for Alloy-Steel Turbine-Type Bolting Material Specially Heat Treated for High-Temperature Service A439-83(1999)奥氏体可锻铸铁铸件Standard Specification for Austenitic Ductile Iron CastingsA447/A447M-93(2003)高温用镍铬铁合金钢铸件(25-12级)Standard Specification for Steel Castings, Chromium-Nickel-Iron Alloy (25-12 Class), for High-Temperature Service A449-04a经淬火和回火的钢螺栓和螺柱Standard Specification for Quenched and Tempered Steel Bolts and StudsStandard Specification for General Requirements for Carbon, FerriticA450/A450M-04碳素钢管、铁素体合金钢管及奥氏体合金钢管Alloy, and Austenitic Alloy Steel TubesA451/A451M-02高温用离心铸造的奥氏体钢管Standard Specification for Centrifugally Cast Austenitic Steel Pipe for High-Temperature ServiceA453/A453M-03具有同奥氏体钢相类似的膨胀系数、屈服强度为50-120Ksi(345-827MPa)的耐高温螺栓材料Standard Specification for High-Temperature Bolting Materials, withExpansion Coefficients Comparable to Austenitic Stainless SteelsA455/A455M-03压力容器用高强度碳锰钢板Standard Specification for Pressure Vessel Plates, Carbon Steel, High-Strength ManganeseA456/A456M-99(2003)大型曲轴锻件的磁粉检查StandardSpecification for Magnetic Particle Examination of Large Crankshaft ForgingsA459-97(2003)镀锌平轧扁钢铠装带Standard Specification for Zinc-Coated Flat Steel Armoring Tape A460-94(2004)e1包铜钢丝绳标准Standard Specification for Copper-Clad Steel Wire Strand A463/A463M-02a热浸镀铝薄钢板Standard Specification for Steel Sheet, Aluminum-Coated, by the Hot-Dip Process A466/A466M-01非焊接碳素钢链Standard Specification for Weldless ChainA467/A467M-01机器链和盘旋链Standard Specification for Machine and Coil ChainA469-04用于发电机转子的真空处理钢锻件Standard Specification for Vacuum-Treated Steel Forgings for Generator RotorsA470-03涡轮机转子和轴用经真空处理的碳素钢和合金锻件Standard Specification for Vacuum-Treated Carbon and Alloy Steel Forgings for Turbine Rotors and ShaftsA471-02涡轮转子转盘和转轮用真空处理合金钢锻件技术规范Standard Specification for Vacuum-Treated Alloy Steel Forgings for Turbine Rotor Disks and WheelsA472-98(2003)蒸汽涡轮机轴及转子锻件的热稳定性的试验方法Standard Test Method for Heat Stability of Steam Turbine Shafts and Rotor ForgingsA473-01不锈和耐热钢锻件Standard Specification for Stainless Steel ForgingsA474-03包铝钢丝绳标准Standard Specification for Aluminum-Coated Steel Wire Strand A475-03镀锌钢丝绳Standard Specification for Zinc-Coated Steel Wire Strand A476/A476M-00造纸厂干燥辊用球墨可锻铸铁件Standard Specification for Ductile Iron Castings for Paper Mill Dryer RollsA478-97(2002)铬镍不锈钢和耐热钢制编织钢丝Standard Specification for Chromium-Nickel Stainless Steel Weaving and Knitting WireA479/A479M-04锅炉及压力容器用不锈钢和耐热钢棒与型材Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure VesselsA480/A480M-04扁平轧制耐热不锈钢厚板材、薄板材和带材通用要求Standard Specification for General Requirements for Flat-Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and Strip A481-94(2000)金属铬Standard Specification for Chromium MetalA482-93(2000)铬铁硅Standard Specification for Ferrochrome-Silicon A483-64(2000)硅锰合金Standard Specification for SilicomanganeseA484/A484M-03a不锈及耐热锻钢棒,钢坯及锻件的规格Standard Specification for General Requirements for Stainless Steel Bars, Billets, and ForgingsA485-03高淬透性耐磨轴承钢的技术规范Standard Specification for High Hardenability Antifriction Bearing Steel A487/A487M-93(1998)受压钢铸件Standard Specification for Steel Castings Suitable for Pressure ServiceA488/A488M-01e1钢铸件焊接规程和工作人员的合格鉴定Standard Practice for Steel Castings, Welding, Qualifications of Procedures and PersonnelA489-04碳素钢吊耳Standard Specification for Carbon Steel Lifting EyesA490M-04a最小拉伸强度为150千磅/平方英寸热处理钢结构螺栓Standard Specification for Structural Bolts, Alloy Steel, Heat Treated, 150 ksi Minimum Tensile StrengthA490-04a最小拉伸强度为150千磅/平方英寸热处理钢结构螺栓Standard Specification for High-Strength Steel Bolts, Classes 10.9 and 10.9.3, for Structural Steel Joints [Metric]A491-03镀铝钢链环栏栅结构Standard Specification for Aluminum-Coated Steel Chain-Link Fence Fabric A492-95(2000)耐热不锈钢丝绳Standard Specification for Stainless Steel Rope WireA493-95(2000)冷镦和冷锻不锈钢和耐热钢丝Standard Specification for Stainless Steel Wire and Wire Rods for Cold Heading and Cold ForgingA494/A494M-03ae1镍和镍合金铸件Standard Specification for Castings, Nickel and Nickel Alloy A495-94(2000)硅钙合金钢技术规范Standard Specification for Calcium-Silicon Alloys A496-02钢筋混凝土用变形钢丝Standard Specification for Steel Wire, Deformed, for Concrete ReinforcementA497/A497M-02钢筋混凝土用焊接变形钢丝网Standard Specification for Steel Welded Wire Reinforcement, Deformed, for ConcreteA498-04无缝与焊接碳素钢,铁素体钢与奥氏体钢制有整体散热片的换热器钢管Standard Specification for Seamless and Welded Carbon Steel Heat-Exchanger Tubes with Integral FinsA499-89(2002)轧制丁字钢轨用的碳素钢棒材及型材的技术规范Standard Specification for Steel Bars and Shapes, Carbon Rolled from T RailsA500-03a圆形与异型焊接与无缝碳素钢结构管Standard Specification for Cold-Formed Welded and Seamless Carbon Steel Structural Tubing in Rounds and ShapesA501-01热成型焊接与无缝碳素钢结构管StandardSpecification for Hot-Formed Welded and Seamless Carbon Steel Structural TubingA502-03结构钢铆钉规范Standard Specification for Rivets, Steel, StructuralA503/A503M-01(2001)e1锻制大型曲轴的超声波检验Standard Specification for Ultrasonic Examination of Forged Crankshafts A504-04e1锻制碳素钢轮Standard Specification for Wrought Carbon Steel Wheels A505-00热轧和冷轧合金钢薄板和带材Standard Specification for Steel, Sheet and Strip, Alloy, Hot-Rolled and Cold-Rolled, General Requirements forA506-04正规质量及优质结构的热轧和冷轧合金钢薄板与带材Standard Specification for Alloy and Structural Alloy Steel, Sheet and Strip, Hot-Rolled and Cold-RolledA507-04优质拉拔,热轧和冷轧合金钢薄板与带材Standard Specification for Drawing Alloy Steel, Sheet and Strip, Hot-Rolled and Cold-RolledA508/A508M-04b压力容器用经回火和淬火真空处理的碳素钢与合金钢锻件Standard Specification for Quenched and T empered Vacuum-Treated Carbon and Alloy Steel Forgings for Pressure VesselsA510-03碳素钢盘条和粗圆钢丝通用要求Standard Specification for General Requirements for Wire Rods and Coarse Round Wire, Carbon SteelStandard Specification for General Requirements for Wire Rods and CoarseA510M-03碳素钢盘条和粗圆钢丝通用要求Round Wire, Carbon Steel [Metric]A511-04无缝不锈钢机械管Standard Specification for Seamless Stainless Steel Mechanical TubingA512-96(2001)冷拉对缝焊碳素钢机械管Standard Specification for Cold-Drawn Buttweld Carbon Steel Mechanical TubingA513-00电阻焊碳素钢与合金钢机械钢管Standard Specification for Electric-Resistance-Welded Carbon and Alloy Steel Mechanical TubingA514/A514M-00a焊接用经回火与淬火的高屈服强度合金钢板Standard Specification for High-Yield-Strength, Quenched and Tempered Alloy Steel Plate, Suitable for WeldingA515/A515M-03中温及高温压力容器用碳素钢板Standard Specification for Pressure Vessel Plates, Carbon Steel, for Intermediate- and Higher-Temperature ServiceA516/A516M-04中温及低温压力容器用碳素钢板Standard Specification for Pressure Vessel Plates, Carbon Steel, for Moderate- and Lower-Temperature ServiceA517/A517M-93(1999)压力容器用经回火与淬火的高强度合金钢板Standard Specification for Pressure Vessel Plates, Alloy Steel, High-Strength, Quenched and TemperedA518/A518M-99(2003)耐蚀高硅铁铸件Standard Specification for Corrosion-Resistant High-Silicon Iron CastingsA519-03无缝碳素钢与合金钢机械管Standard Specification for Seamless Carbon and Alloy Steel Mechanical TubingA521-03一般工业用闭式模钢锻件Standard Specification for Steel, Closed-Impression Die Forgings for General Industrial Use A522/A522M-01低温用锻制或轧制含镍8%和9%的合金钢法兰,配件,阀门和零件规格Standard Specification for Forged or Rolled 8 and 9% Nickel Alloy SteelFlanges, Fittings, Valves, and Parts for Low-T emperature。

面料检验标准美国四分制英文版Adoption of the United States a quarter of the standard score system:Defect size score<= 3 inches 13-6 inches 2 hours6-9 inches 3 hours> 4 hours 9 inchesDefect, whether to or by the zonal, regardless of what faults are visible in principle.A roll of fabric defect score may not exceed 40 minutes (to 100 yards straight as the standard, does not consider width).The entire batch of large cargo Defect score shall not exceed 22 minutes (to 100 yards straight as a standard, that is 1000 yards straight scores may not be more than 220 points, does not consider the width).If any bolt of cloth for defects in the three yards, no matter how many faults do not accept the score, must be cut open; any roll if regularity defect (more than 3), regardless of how many defects are not acceptable, must be cut open.There is a roll of cloth can not be received aspirin (a roll of knitted fabric permit access has two horses that paragraph 3, each received between horses do not need stitching, each not less than 10 yards, each horse received 4 points assessment. ).Big bad cylinder goods can not be less than 4.Edge with the two color difference Selvedge must be above 4.5.Width requirement for the effective width.Gram in accordance with the order request, an acceptablerange of + / -5%. However, we must pay special attention to code length, not short code. For knitted fabrics, it is recommended by Weight Factory production under the deviation.Head cloth, cloth tail joints must be clean cut open.If a large defect (as to more than 50CM) must be cut open.Woven fabric in the hole if it must be cut open; knitted fabric in the hole must be opened if more than 30CM shear. Any two consecutive off yarn (including 2) are regarded as the hole, hole, large or small, all 4 assessment points / month.Large cargo inspection when the code length needed to be tested: woven fabric can be run through the code machine,打码机, hanging code or manual code length measurement; knitted fabric can be from the interception of goods between SMPL, measured the actual code weight, then re-calculate the actual volume of the actual large goods yards.Large cargo ramp weft (torque)A. Woven fabric: general plain plain requirements at 2%, a plain twill requirements at 5%, 10OZ twill fabrics need to do more than pull oblique oblique weft process shall not exceed 8% (washed, not more than oblique weft 5% QC to be tested on the spot); if the yarn-dyed and printed fabrics, they are required at less than 2%.B. Knitted fabrics: Only yarn plain cloth will have such a problem: 100% cotton 21 single-sided oblique weft cloth shall not exceed 15%, 100% cotton 32 single-sided cloth weft inclined not to be more than 20%, CVC21 Support single-sided oblique weft cloth shall not exceed 8%, CVC32 Support single-sided oblique weft cloth shall not exceed 10%,16. Lattice Size: Large cargo overall lattice size (more like confirmation / color draft) deviation shall not exceed 3%; largecargo Medium fabric inconsistent if the size of lattice, the size difference to the deviation by not more than 3%, weft to the control provisions in the Order of the width requirements.17. Washing: If clothing to be washed, then SUPPLIER need me obtain a single Division of washed color quality confirmation samples at QC inspection to provide pre-washed and washed, the big bad cargo tanks.18. Large cargo volumes per head three yards inside the defect score shall be less than 3 minutes, or else must be cut open.19. If the fabric to be tested and approved prior Samples provided does not match its hue must match.20. Testing Quantity: at least testing large quantities of goods 10%, when the large quantity goods at less than 1000 yards, it would take 100 percent inspection; testing according to the largest cargo tank of the color and quantity of its proportion of randomly selected.21. Inspection conditions: Examination to be about one yards from the cloth, at least four 40W fluorescent tubes lighting, but the thin light-colored fabric samples to be spread flat on a table at hand inspection, especially white fabrics; machine or hand speed to be able to see the cloth cover defects prevail.22. Single volume measurement of fabric must be at least 3 times width (first, middle and end of all time), Order of the width of all refer to the effective width (width is the effective removal of cloth woven edge and pinhole setting machine, cloth no printing on the main and not on the coating or other surface treatment has not been part of the measurement of the width.)23. Large cargo must be required to test and distinguish between LOT-color, and single-code and detail on cargopackaging and quantity specified cylinder, the same packaging permit only color there is a LOT.24. Large Medium large cargo crane line faults have to specify (major faults will be treated as one-third or a quarter of the defect.).25. There is a serious smell of fabric can not accept it.26. There is such a big shipment in question, this big cargo will have a direct REJECT:A. Cylinder or bad side in the color difference less than the required standards.B. Obvious from the ball, die cotton phenomenon.C. If the inspection when the inspection of the total quantity REJECT quantity of 5%, then the entire batch of large cargo unacceptable.D. Selvedge distance more than 0.5 inches for more than three yards faults.27. The beginning and end of each volume to be knocking on fabrics chapter and indicate the volume number and the code length28. Fabric to the factory pre-production, SUPPLIER fabric have to be tested.OTHER CUSTOMER:LIZ:Score according to criteria adopted by the United States a quarter of the system (with reference to the score LOLLYTOS standard), but requested that the entire batch of large cargo score equal to less than 13 points / 100 yards straight, single-vol ume score equal to less than 16 points / 100 yards straight,or else be consider unqualified.AT LAST:1. Score standards assessed by the United States a quarter system. Single-volume score shall not exceed 40 minutes / 100 square yards, the whole batch of large cargo Defect score no more than 22 points / 100 square yards.2. Shrinkage rate: 100 percent tested requirement large cargo fabric shrinkage, especially stretch fabrics or thin fabrics, have to pay special attention to the shrinkage rate of large goods.3. Inspection conditions: 1 yards away from the fabric, at least four 40W fluorescent lamp, no light at the end of test machine or hand speed to no more than 20-30 yards / min.4. Score calculated as follows: per 100 square yards of Score Assessment of large goods.5. Inspection Quantity: At least testing large quantities of goods 10%, at least 65% of the goods we can not go on The End packaging inspection, a random sample large cargo inspection.6. SHADING, handle such a large deviation, the largest cargo will be directly REJECT.7. Edge in color requirements shall not be less than 4.5 (AATCC GREY SCALE).8. The first three yards of woven fabric knitted fabric 5 yards may not be the first there is a large defect.9. Continuity faults for more than three yards away to be opened.10. Woven fabric in the hole if it must be cut open; knitted fabric in the hole must be opened if more than 30CM shear. Any two consecutive off yarn (including 2) are regarded as the hole, hole, large or small, all 4 assessment points / month.11. Latitudinal arch, oblique, twist requirements:Less than or equal to 60 inches Width: less than 1.5 inches Width greater than 60 inches less than or equal to 90 inches: less than 3 inchesGreater than 90 inches Width: less than 4 inches12. There is a serious smell of fabric can not accept it.13. Then horses, the smallest segment length, the length ofa single volume by the factory and after discussion SUPPIER decide. Recommendations: a single volume more than 100 yards in length, single-volume permit has 2 splicing, the smallest segment grew at 20 yards.14. If the major goods did not pass inspection, to be with AT LAST or AT LAST place of office communication make the final decision after consultation; factories have to review 100 percent fabric large cargo, the report failed fabrics give quantity AT LAST, and then arranged to do the necessary wear and tear or through consultations with the AT LAST decide compensate for their losses.PCC:1. Criterion-referenced inspection SCHOOL / FH / HT.2. Large number of cargo tanks fabrics all have to send guests confirmed that large number of cargo tanks shall not exceed the number of guests confirmed cylinder.OWW:Inspection must be more than one week in advance to inform my SecretaryInspection, it is important to provide a single box as well as related information (cylinder No. / Volume)Large cargomore than 80 percent complete before we can accept the inspection, such as less than 80 percent must be confirmed before they can oww inspectionInspection when the goods should pay attention to big color / edge in the bad / before and after the bad / bad-cylinder, fabric suppliers are required to retain large cargo horses 6 months Random quantity is as follows:10,000 yards or 1,000 yards the following checks10,001 -> 20,000 yards random 8% of the total number of 20,001 -> 30,000 of the total number of code samples 6%30,000 yards more than 4 percent of the total number of spot checksExamination per minute when the speed is not more than twenty-five yardsThe ultimate impact of the reduction of wear and tear wear and tear and finished the defect must be points'Quarter system': each code a maximum of 4 points deducted The continuity of the faults, we must open cutOrder on the width for the effective widthSelvedge 1.5 centimeters away from the defect may not need to mark points (in the effective width apart)Tear, and holes cut by more than 1 centimeters should be cut1 cm hole in the buckle within 4 hoursDeducted 3 points and 4 points to have identification (hung up)Washing signs to markEach volume has access permit approved, but including the joints, the head and tail up to 1.5 meters within 2 points deducted Large cargo shall not exceed 100 yards on average 25minutesA single volume an average of 100 yards may not exceed 30 hours, more than 30 points as second-class goodsWhether the entire batch of large cargo through the average, to a second-class goods must be agreed owwQC inspection according to the above criteriaAt oww agreed conditions, the second-class goods in quantity must be controlled at 10% ofFactory inspection reports must have the signature of the representativeFactory goods if there is any second-class large cargo must send samples to confirm OWW AGENTIf the QC inspection found that there is no confirmation of a second-class goods, factories must immediately arrange to rework and re-packaging, or before shipment to replace the number of rejectionSuch as because of any problem caused by the quality of More or Less, from full responsibility for FactoryIf, after shipping, GCO found cloth goods have quality problem, will be arranged to re-test the entire batch of large cargo, but the costs borne by the FCODichroic packaging for each packet of marked-cylinder No. / Code number / packet number / volume number, cloth cloth head and tail have to knock Chapter。