天逸DSP-680效果器快速操作指南一、本机主要特点1、本机出厂状态共有100种出厂模式和10种用户模式。
10种用户模式与工厂模式前十种相同。
用户模式可自行调节更改后保存，工厂模式为固化模式，只能调用不可更改。
2、本机出厂默认最大锁定音乐音量为55，话筒音量为64，用户可根据实际情况设定最大音量限制和开机音量限制，设定并锁定本机以后开机默认最大音量为用户自行设定音量。
3、本机出厂状态音乐为直通模式，如需要调可按音乐音量键进入调节。
4、长按菜单键（MENU）五秒钟锁定或解除锁定工作状态，上锁同时保存当前音乐音量，话筒音量，音乐效果状态，且在下次开机后所有音量不会随模式变化而变化。
5、本机上锁后音乐音量，话筒音量，工厂模式，用户模式，反馈抑制模式均可调，但不会保存。
6、音乐信号会随话筒信号的开启自动衰减，话筒关闭会音乐信号自动淡入提升。
7、解锁后调节好工程参数进行保存时按存储键（MEMORY）配合音量旋钮可存储到指定模式，保存时音乐音量，话筒音量，反馈抑制三项不随机保存。
该三项保存时间为整机上锁的同时保存。
如调节完成后没有锁定机器，则开机会自动恢复到上一次锁定状态或是出厂设置状态。
8、重新开机后，效果所在状态为锁定前调节好的模式及效果状态。
9、中置/环绕音量在MIC SETUP菜单里单独可调，话筒参数在MIC菜单内可单独调节输出带效果，带音乐，比主声道音量小6dB。
10、超低音输随话筒的开启自动检测到话筒信号后关闭，关闭话筒信号自动开启超重低音输出。
11、本机设置有话筒及音乐信号测噪声门，用户在设置菜单中可自行设置，当话筒信号小到一定程度时自动开启此功能。
12、话筒及音乐信号均设置有EQ调节（即声音频响），调节方法见以下操作菜单。
13、本机的锁定键为常按MENU，开关机效果次数锁定为菜单键（MENU）配合音量旋钮完成。
二、MENU菜单操作1、Factory Mode -Factory Mode x Load?工厂模式——预置100种话筒效果，按下MENU键，转动MIC旋钮至该功能，向下按MIC 音量键进入模式选择，0—100种模式可任意调用，选定所需要模式再次下按该键确认。
32-Channel Sound Reinforcement ConsoleS R 32•4-V L Z FeaturesLow noise/high headroom XDR™ (Extended DynamicRange) mic preamps with excellent RFI rejectionNew high-performance 2068 op-amps for incredibly low noise and distortionImproved cooling for even greater thermal protection 28 mic/line mono, and 2 stereo line channels True 4-bus designSolo, pan, and 16 kHz Air EQ on each submaster 6 individual aux sends per channel (2 pre, 2 post, 2 switchable pre/post)3-band swept midrange EQ on mic channels; 4-band fixed on stereo line channels 75 Hz low-cut filters on mic channelsMute, solo, signal present and OL LEDs on every channel 6 aux send masters with individual solos 4 stereo aux returns with EFX monitorSeparate Talkback section with mic preampDouble-bused sub outs for easy multi-track routing Balanced stereo TRS & XLR main outputs Balanced XLR mono output with level controlApplicationsLive sound mixing Multi-track recordingIntroductionTHE SR32•4-VLZ PRO is the latest update of our SR32•4sound reinforcement console, incorporating our ultra-high quality XDR™ (Extended Dynamic Range) mic preamps with the best RFI rejection of any sound reinforcement mixer design on the market.Like all of Mackie Designs’ mixers, the SR32•4-VLZ PRO is designed for rugged, 24-hour-a-day use. With its mul-tiple input/output configurations, true 4-bus architecture, 6 aux sends, and extensive routing capabilities, it can be used in a variety of live sound and recording applications. Its sturdy steel construction houses rugged, double-sided SMT-plated fiberglass circuit boards, and 60 mm faders with ultra-tight lip seals for keeping out dust and other contaminants. Impact-resistant knobs are mounted so they “ride” just above the steel chassis.The SR32•4-VLZ PRO has 28 mono mic/line input chan-nels, with XLR mic inputs and 1/4" TRS line inputs, and 2 stereo line input channels with 1/4" TRS inputs. All mono channels have TRS insert jacks (tip = send, ring = return). Each channel strip has an input trim, 6 aux sends (2 pre-fader, 2 post-fader, and 2 switchable pre or post), 3-band EQ with sweepable midrange (4-band EQ on the stereo chan-nels), pan control, and mute, solo, and bus assign switches. A 60 mm fader provides output gain for each channel. Twenty-eight XDR mic preamps provide high-headroom and low-noise. They are impedance-independent, so the frequency response remains constant whether the mic pre-amp is presented with an extremely high- or low-impedance load. Additionally, each channel has its own switchable low-cut filter (18 dB/octave @ 75 Hz).The mono channel EQs provide a range of ±15 dB at the following frequencies: 12 kHz shelving high-frequency EQ, 100 Hz to 8 kHz sweepable peaking mid-frequency EQ, and 80 Hz shelving low-frequency EQ. The stereo channels (21-24) provide ±15 dB of boost and cut at the following frequencies: 12 kHz shelving high-frequency EQ, 3 kHz peaking high-mid frequency EQ, 800 Hz peaking low-mid frequency EQ, and 80 Hz shelving low-frequency EQ.(continued on page 2)R E L A T E D P R O D U C T SSR24•4-VLZ PROCrosstalk(1 kHz @ 0 dBu, 20 Hz to 20 kHz bandwidth, channel in to Main Left outputs):Channel fader down, channels at Unity –89.5 dB Channel muted, channels 2-16 at Unity –88.7 dB Frequency Response(any input to any output):20 Hz to 60 kHz +0/–1dB 10 Hz to 100 kHz+0/–3dB Maximum LevelsMic preamp input +22 dBu All other inputs +22 dBu Balanced XLR outputs+28 dBu All other outputs+22 dBu ImpedancesMic preamp input 1.5 kΩAll other inputs >10 kΩAll outputs120 ΩEqualizationLo EQ Shelving 80 Hz +15 dB Mid EQ (mono ch) Peak 100 Hz-8 kHz +15 dB Hi EQ Shelving 12 kHz +15 dB Microphone PreampE.I.N. (150 Ω terminated, max gain)–129.5 dBm Power Requirements60 wattsPhysicalDimensions (HxWxD): 5.60" x 39.25" x 19.20"142.24 mm x 996.95 mm x 487.68 mm Net Weight: 32•4-VLZ PRO 40.7 lbs (18.8 kg)the left and right mains, 1/4" TRS line outputs for subs 1-4, and an XLR mono main output. The mono main out has its own level control, so a mono mix can be sent to another zone and adjusted accordingly.The Phones/Control Room switch and level control are connected to two stereo headphone outputs and the left and right Control Room output, allowing the stereo Tape Return, Left/Right Main Mix, and Solo to be monitored.A stereo playback device can be monitored via the Tape Return Inputs. Tape Return to Phones/C-R routes the tape playback signal into the monitor system and meters, and the Tape Return knob adjusts the level of playback, which can be monitored via headphones. Tape Return signals can also be assigned directly to the Main Mix. The SR32•4-VLZ PRO also has RCA-style Tape Outs for output to conventional stereo recording devices.Each of the six aux sends has its own individual master send control, driving 1/4" TRS output jacks. Six stereo aux returns are provided, with 1/4" TRS input jacks. Two aux returns can be folded back into Aux Sends 1 and 2 via their own volume controls to add effects in stage monitors.An XLR input is provided for a talkback mic, which can be assigned to the Main Mix or to Aux 1-2. The talkback mic has a level control in the talkback section.SR32•4-VLZ PRO TopSR32•4-VLZ PRO Rear PanelSR32•4-VLZ Pro DimensionsSR32•4-VLZ PRO Block Diagramswitches; and level indicating LEDs. The submix outputs shall each have level, pan, and “air” controls; solo and assign switches; and a bus access insert jack. The main outputs shall share a stereo master output fader and shall be fitted with insert jacks. Additionally, the mixer shall include a pre-fader/post fader solo function, a main monaural output with level control derived from the main stereo outputs, 6 monitor/effects send outputs, 4 stereo effects return inputs with switching and control functions, 1 stereo control room monitor output, 2 stereo headphone outputs, 1 set of stereo tape recorder conve-nience outputs, and 1 set of stereo tape monitor inputs.2. POWER SUPPLY.All necessary operating voltages for the mixer shall be provided by an internal power supply.3. INPUT CHANNEL CONNECTIONS. Each monau-ral channel (1-28) shall include an XDR™ (Extended Dynamic Range) electronically balanced microphone input, using an XLR-3-F-type connector, accepting nominal levels from –60 dBu to +4 dBu via a rotary Trim control. Phantom power shall be globally controlled via a rocker-type switch. Each monaural input channel shall also have an electronically balanced line level input, accommodating a nominal line level of between –10 dBV and +4 dBu, and appearing on the rear panel as a 1/4" TRS phone jack. Each stereo input channel shall have left and right electronically balanced line level input, accommodating a nominal line level of between –10 dBV and +4 dBu, and appearing on the rear panel as 1/4" TRS phone jacks. These jacks shall be fitted with internal switching contacts to accommodate monaural configura-tion. Additionally, each of the monaural input channels (1-28) shall offer an unbalanced insert connection, appearing on the rear panel as a 1/4" TRS phone jack.4. INPUT CHANNEL LEVEL AND ASSIGNMENT CONTROLS AND INDICATORS. Each monaural input chan-nel shall be equipped with a preamplifier gain control,a solo switch, a mute switch, three bus assignment ing equalizer with the knee set at 80 Hz and a range of +15 dB; a low-mid-frequency peaking equalizer centered at 800 Hz and a range of +15 dB; a high-mid-frequency peaking equalizer centered at 3.5 kHz and a range of+15 dB; and a high frequency shelving equalizer with the knee set at 12 kHz and a range of +15 dB.6. INPUT CHANNEL AUXILIARY SENDS. Each mixer input channel shall have 6 monaural auxiliary send con-trols. Two auxiliary send controls shall be fixed as pre-fader sends; two shall be fixed as post-fader sends; and two shall be switchable between pre-fader and post-fad-er. All auxiliary sends shall be post-mute switch.7. MAIN OUTPUT CONNECTIONS. The mixer shall have electronically balanced, line-level left and right main outputs, appearing on male XLR-3 type connectors and impedance balanced on 1/4" phone TRS jacks on the rear panel. Additionally, the main buses shall offer left and right unbalanced insert connections, appearing on the rear panel as 1/4" phone TRS jacks. Further, there shall be a main, electronically balanced, monaural output derived from the main stereo output, appearing as a male XLR-3 type connector on the rear panel. There shall be an output level control to adjust the main monaural output level.8. OTHER OUTPUT AND MONITORING CONNECTIONS. The mixer shall have the following impedance balanced line-level connections, appearing as 1/4" TRS jacks on the rear panel: submix bus outputs 1-4, also wired in parallel respectively to submix outputs 5-8; left and right control room monitor outputs, left and right tape monitor outputs, left and right tape monitor inputs. For conve-nience, the left and right main outputs (unbalanced) and the left and right tape monitor inputs shall also appear as RCA phono jacks on the rear panel. There shall also be two stereo headphone outputs on the rear panel of the mixer, carrying the control room monitor signals at levels and impedances proper for headphones. Each head-phone output connection shall be a stereo 1/4" jack.324 16220 Wood-Red Road NE, Woodinville, WA 98072 USA 888.337.7404,fax425.487.4337,****************Electronic files for this product available at: /installedThis Specification Sheet SR32VLZPRO_SS.PDF Owner/Operator’s Manual SRVLZPRO_OM.PDF CADD files SR32VLZPRO.DXF9. OUTPUT AND MONITORING CONTROLS AND SWITCHES. The mixer shall include one linear fader control for gain adjustment of main L/R outputs, covering a range from infinite attenuation to +10 dB above unity gain. A tape monitor switch shall alternately select either the main L/R outputs or the signal at the tape inputs as the source for the control room and headphones monitoring circuits. There shall be a stereo dual-channel rotary control for gain adjustment of the control room and headphone monitor output. The mixer shall have a stereo dual-channel control for adjustment of the monitoring level of the internal solo signals, and a light to indicate channel solo condition. The solo system shall be capable of switching between PFL (pre-fader listen) and AFL (after-fader listen––solo in place) operation.10. OUTPUT METERING. The mixer frame shall include two 13-segment LED meters each displaying a signal range from –40 dBU to +10 dBu, each with an additional LED indicating mixer clipping level at +22 dBu. The meters shall monitor the main left and right output channels; alternately, the meters shall monitor the tape return sig-nals when the tape monitor switch is depressed; or, the soloed input channel signals when the solo switch is depressed.11. AUXILIARY SEND CONNECTIONS. The mixer shall include impedance balanced, line-level outputs from the six auxiliary send buses, appearing on the rear panel as 1/4" TRS phone jacks.12. AUXILIARY RETURN CONNECTIONS. The mixer shall include 4 stereo auxiliary return inputs. Each auxiliary return shall have a left and a right balanced line-level input, accommodating a nominal line level of between –10 dBu and +4 dBu, and shall appear on the rear panel as 1/4" TRS phone jacks. The jacks shall be fitted with internal switching contacts to accommodate monaural configuration.13. AUXILIARY RETURN CONTROLS AND SWITCHES. The mixer shall include 4 dual-channel auxiliary return gain controls, each feeding the main stereo buses. Auxiliary returns 1-2 shall have their signals assignable to auxiliary send buses 1 and 2, respectively, through rotary level con-trols. Auxiliary return 4 shall be assignable to three differ-ent pairs of destinations, feeding either the main left and right buses or the submix buses.14. PHYSICAL CONFIGURATION. The mixer shall have a steel chassis frame painted grey-black and designed to rest on a horizontal surface. The SR32•4-VLZ PRO’s dimen-sions shall be 6.1" (155mm) high by 39.3" (997mm) wide by 19.2" (487mm) deep.15. SPECIFICATIONS. In addition to specifications previously cited, the mixer shall meet or exceed the fol-lowing specifications. Frequency response, microphone input to any output, 20 kHz to 60 kHz, +0 dB/ –1 dB; Total Harmonic Distortion (THD), any input to any output, 1 kHz @ +14dBu, 0.004%; Equivalent Input Noise (EIN), microphone input to insert send, –129.5 dBm; Common Mode Rejection (CMR), microphone input to insert send, maximum gain, 1 kHz, better than 90 dB; Typical Main Output noise, all channels assigned, odd channels panned left, even channels panned right, all faders down –94.7 dBu; Signal to Noise ratio, ref +4 dBu operating level, 90 dB; Attenuation, ref. 0 dB @ 1 kHz, Main Mix level con-trol down, –85 dBu; Channel Mute engaged, –84 dBu; Channel Gain control down, –83 dBu; Input impedance, microphone inputs, 1.5 k Ω; Channel Insert return, 2.5 k Ω; all other inputs, greater than 10 k Ω; Output impedance, Tape Out, 1.1 k Ω; All other outputs, 120Ω.16. DESIGNATION. The mixer shall be a Mackie Designs SR32•4-VLZ PRO.Mackie Designs continually engages in research related to product improvement. New material, pro-duction methods, and design refinements are introduced into existing products without notice as a routine expression of that philosophy. For this reason, any current Mackie product may differ in some respect from its published description, but will always equal or exceed the original design specifica-tions unless otherwise stated. ©1999–2002 Mackie Designs Inc. All rights Reserved. Mackie and the “Running Man” figure are registered trademarks of Mackie Designs Inc.。
