Z2C151-RC-10中文资料

元器件交易网
FERRITE CHIP BEADS
1. PART NO. EXPRESSION :
Z2 SERIES
Z2C300-RF-10
(a)(b)(c) (d) (e)(f) (g)
(a) Series code (b) Dimension code (c) Material code (d) Impedance code : 300 = 30
60 seconds
4±1.0 seconds
Terminal Strength
The terminal electrode & the dielectric must not be damaged by the forces applied on the right conditions.
For Z Series : Size 1 2 3 4 5 6 Force (Kfg) 0.2 0.5 0.6 1.0 1.0 1.0 1.5 2.0 > 25 Time (sec)
PERFORMANCE
The ferrite should not be damaged by forces applied on the right condition.
R0.5(0.02) 1.0(0.039)
TEST CONDITION
Series name Z2 Z3 Z4 Z5 Z6 Z7 Z8 mm (inches) 0.80 (0.033) 1.40 (0.055) 2.00 (0.079) 2.70 (0.106) P-Kgf 0.3 1.0 2.5 2.5
Preheating Dipping 245°C 150°C Natural cooling
Preheat : 150°C, 60sec. Solder : Sn-Ag3.0-Cu0.5 Solder Temperature : 245±5°C Flux for lead free : rosin Dip Time : 4±1sec.
0
FR UEN EQ CY(M ) Hz
FR EQU CY(MHz EN )
Z2C1 -RC-1 F Z2C 1C-121T0 0 CM 160821 -00 21-RC 3
400
0 FZ2C11C-151T0 CM 51 1608-RC-1 3 Z2C 51-RC -00
600
500
IMP AN ED CE(Ohm )
IMP AN ED CE(Ohm )
300
400
200
Z X
300
Z
200
100
X
100
R
0 1 10 100 1000
0 1 10 100
R
1000
FR EQU CY(MHz EN )
FR EQU CY(MHz EN )
NOTE : Specifications subject to change without notice. Please check our website for latest information.
03.07.2008
SUPERWORLD ELECTRONICS (S) PTE LTD
PG. 3
元器件交易网
FERRITE CHIP BEADS
8. RELIABILITY & TEST CONDITION :
Z2 SERIES
ITEM
Electrical Characteristics Test Impedance DC Resistance Rated Current Temperature Rise Test Solder Heat Resistance
Chip A
Random Vibration Test
Appearance : Cracking, shipping & any other defects harmful to the characteristics should not be allowed. Impedance : Within ±30% Drop 10 times on a concrete floor from a height of 75cm. Appearance : No damage. Impedance : Within ±30% of initial value.
Refer to standard electrical characteristics list
30°C max. ( t) Appearance : No significant abnormality Impedance change : Within ±30% No mechanical damage Remaining terminal electrode : 70% min.
03.07.2008
SUPERWORLD ELECTRONICS (S) PTE LTD
PG. 2
元器件交易网
FERRITE CHIP BEADS
7. IMPEDANCE VS. FREQUENCY CURVES :
Z2 SERIES
Z2C221 C-00 0 FC 1608C -RC-1 M Z2C221 -22exture Strength
The terminal electrode & the dielectric must not be damaged by the forces applied on the right conditions.
20(.787) Bending 45(1.772) 45(1.772) 40(1.575)
5. GENERAL SPECIFICATION : a) Temp. rise : 30°C Max. b) Rated current : Base on temp. rise c) Storage temp. : -55°C to +125°C d) Operating temp. : -55°C to +125°C e) Resistance to solder heat : 260°C.10secs
150
0 FZ2C600-RF-16 CM 600-RF -00 Z 1608 2C C-600T0
300
120
240
IM PED C Ohm AN E( )
IM PED C Ohm AN E( )
90
180
60
Z
120
Z X R
1 10 100 1000
30
X R
60
0 1 10 100 1000
03.07.2008
SUPERWORLD ELECTRONICS (S) PTE LTD
PG. 4
元器件交易网
FERRITE CHIP BEADS
8. RELIABILITY & TEST CONDITION :
Z2 SERIES
ITEM
Bending Strength
1600
IMP AN ED CE(Ohm )
IMP AN ED CE(Ohm )
1200
Z
1200
Z
800
800
400
X
0 1 10
400
X
0
R
100 1000
R
1 10 100 1000
FR EQU CY(M ) EN Hz
FR EQU CY(M ) EN Hz
Z2C1 -10 -10 Z2C102-R 2T0 FC 1608C A-00 M 02-RA 0
NOTE : Specifications subject to change without notice. Please check our website for latest information.
H
03.07.2008
SUPERWORLD ELECTRONICS (S) PTE LTD
PG. 1
(e) R : Reel (f) Current code : F = 600mA (g) 10 : Lead Free
2. CONFIGURATION & DIMENSIONS :
A D L G
B
C
PCB Pattern Unit:m/m
A
B
C
D
G 0.60 Ref.
H 0.80 Ref.
L 2.60 Ref.
1000
0
FR EQU CY(M ) EN Hz
F REQU CY EN (MH z)
Z2C471 1T0 -RB 2 0 FC 1608C B-00 M Z2C471 -47 -1 -R
1600
2000
Z2C601 -R B -00 -RB -1 FC 1608C 1T0 M Z2C601 -60 0 1
Preheating Dipping 260°C 150°C Natural cooling
60 seconds
10±0.5 seconds
Solderability
More than 90% of the terminal electrode should be covered with solder.
PERFORMANCE
TEST CONDITION
HP4291A, HP4287A+16092A HP4338B 1. Applied the allowed DC current. 2. Temperature measured by digital surface thermometer. Preheat : 150°C, 60sec. Solder : Sn-Ag3.0-Cu0.5 Solder Temperature : 260±5°C Flux for lead free : rosin Dip Time : 10±0.5sec.