QUICK START GUIDEDVX-3266-4K 8x4 All-In-One Digital Video Presentation Switcher OverviewThis guide pertains to the Enova DVX-3266-4K all-in-one digital video presentationswitcher. The purpose of this guide is to illustrate how the device is to be installedand set up in its simplest configuration by a trained technician.What's in the Box?The following items are included with the DVX-3266-4K:• [1] DVX-3266-4K• [1] AC Power Cord with US Pins• [1] AC Power Cord with UK Pins• [1] AC Power Cord with EU Pins• [8] 3-Pin, 3.5mm Phoenix Male Connector• [3] 4-Pin, 3.5mm Phoenix Male Connector• [4] 5-Pin, 3.5mm Phoenix Male Connector• [1] 3-Pin, 5.08mm Phoenix Male Connector• [1] 4-Pin, 5.08mm Phoenix Male Connector• [2] IR Emitter• [2] Front Rack Mounting Brackets (Attached)• [4] Rubber Foot (Attached)• [1] This Quick Start GuidePowerIEC Power Cord Connector: ~100-240V AC, 50/60Hz, 10AEnvironmental RequirementsThe environmental requirements for DVX-3266-4K are as follows:• Operating Temperature: 32°F (0°C) to 104°F (40°C)• Storage Temperature: -4°F (-20°C) to 158°F (70°C)• Operating Humidity: 5% to 85% RHGetting ConnectedEnsure that the DVX is connected to an IP network using the LAN port. Once theDVX is powered on, you can connect to it through its IP address.NOTE: The DVX fully supports IPv6 network addressing. If the LAN port is connectedto an IPv6 capable network it will self select an appropriate IPv6 address based onthe discovered address parameters of the network to which it’s attached.Locating the IP Address of the DVXYou can locate the IP address of the DVX by using the buttons on the front panel ofthe unit. The IP address appears on the LCD display on the front panel of the DVX.Perform these steps to locate the IP address of the unit:• Press the STATUS button on the front panel of the unit to open the StatusMenu. The Status options appear on the LCD display.• Use the UP and DOWN navigational arrow buttons to navigate through theoptions until you find the IP address. Note the IP address for future reference.NOTE: You can use the Status menu to verify current TCP/IP settings using the UPand DOWN navigational buttons.Switching to Static or Dynamic IP AddressingTo toggle between static or dynamic IP addressing, the controller cannot becurrently booting or it must be in ID Mode. If these conditions are met, holding theID pushbutton for 10 seconds to change the current IP addressing mode.Changing the IP Address Once You Are ConnectedPerform these steps to change the IP address once you are connected to thecontroller:NOTE: Ensure the PC you are using to connect to the controller has the latestversion of NetLinx Studio 4.0 installed on it.1. In NetLinx Studio, select Diagnostics > Network Addresses from the menu barto open the Network Addresses dialog.2. Click Get IP Information to enable the fields for editing.3. Enter the System, Device (0 for NetLinx Masters), and Host Name information.4. To specify a network IP address, select Specify IP Address.5. Enter the IP parameters into the available fields.6. Click Set IP Information to retain the pre-reserved IP Address to the Master.7. Click Reboot Device to finish assigning the IP address to the Master, and clickOK to close the dialog.Default SettingsThe following sections list the default settings for the controller.Default User Names and PasswordsThe following table lists the default user names and passwords for accessing theDefault IP AddressesConfigurationAll items in this section require accessing the front panel of the DVX.Using the Front Panel ButtonsYou can access the configuration settings for the DVX by using the VIDEO MENU,AUDIO MENU, SWITCH, and STATUS buttons on the front panel of the DVX. Pressingany button opens its respective menu on the LCD display on the front panel.Press the TAKE pushbutton to implement an audio/video switch while you are inthe Switch menu on the LCD display. When in an audio or video menu, press thebutton to cycle through audio and video inputs or outputs (depending on themenu.)Use the Navigational buttons to traverse the available options and change theirvalues.FIG. 1 displays the navigational function of each button.Move upMove downDecreasechange theof the selectedparametervalue, orstateFIG. 1 NAVIGATION BUTTONSSelecting an Audio Test ToneSelecting a test tone for your input source can help determine if you have youraudio devices connected correctly. Perform these steps to select a test tone:1. Press the AUDIO MENU button on the front panel of the DVX to open theAudio Output menu.2. Press the left and right navigation buttons to select the output on which toplay the test tone (ALL, 1, 2, 3, or 4).3. Press the down navigational button until the Test Tone option appears.4. Use the left and right navigational buttons to select an appropriate audio testtone.Accessing the WebConsoleThe DVX has a built-in WebConsole that allows you to change configuration settings via a web browser on any device with access to the DVX.The WebConsole consists of a series of web pages that are collectively called the “Master Configuration Manager”. Refer to the NX Series NetLinx Integrated Controllers WebConsole & Programming Guide for details on the WebConsole. From any PC with access to the LAN that the target DVX resides on:1. Open a web browser and type the IP Address of the target DVX in the AddressBar.2. Press Enter to access WebConsole for the DVX. The initial view is theWebControl page.Enabling SecurityTo enable security:1. Select the Security tab on the WebConsole. The System Security Detailsappear.2. Click the Enabled check box to enable security and activate the Accessoptions.3. Select the Access options which you want to require a login and password.4. Configure users and groups as necessary.Wired 802.1X SecurityThe DVX supports wired 802.1X, an IEEE Standard for Port-based Network Access Control. To enable wired 802.1X, you must load an 802.1X certificate file to your controller using NetLinx Studio. Once you add the certificate file to your workspace, NetLinx Studio transfers the file to the appropriate directory on the controller.1. Click to select (highlight) a System (in the Workspace tab of the WorkspaceBar).2. Right-click on the Other folder to access the Other File Folder context menu,and select Add Existing Other File.3. In the Add Existing Other File dialog, locate and select the certificate file (.crt)that you want to add to the selected System. Change the Files of Type option to All Files (*.*) to look for other file types, if necessary.4. Click Open to access the File Properties dialog, where you can view/editgeneral file information for the selected file.5. Click OK to add the file to the selected System. The file should now appear inthe Other folder under the selected System.Hardware InformationThis section lists important hardware information for the DVX.Port NumbersMounting the DVX into an Equipment RackThe DVX occupies two rack units in a standard equipment rack. Install the included rack mounting brackets using the supplied mounting screws prior to securing the unit in the rack.CAUTION: The DVX should not be installed in enclosed spaces. ALWAYS ensure that the rack enclosure is adequately ventilated. Do not block any ventilation openings. It is recommended that you leave 1 RU of space above the DVX when you install it in a rack. DO NOT stand other units directly on top of the DVX when it is rack mounted, as this will place excessive strain on the mounting brackets.ALWAYS ensure that the rack enclosure is adequately ventilated. Do not block any ventilation openings. Sufficient airflow must be achieved (by convection or forced-air cooling) to satisfy the ventilation requirements of all the items of equipment installed within the rack.Additional DocumentationAdditional documentation for this device is available at .Last Revised: 25/02/2020© 2020 Harman. All rights reserved. NetLinx, Enova, WebControl, AMX, AV FOR AN IT WORLD, and HARMAN, and their respective logos areregistered trademarks of HARMAN. Oracle, Java and any other company or brand name referenced may be trademarks/registered trademarks oftheir respective companies.AMX does not assume responsibility for errors or omissions. AMX also reserves the right to alter specifications without prior notice at any time.The AMX Warranty and Return Policy and related documents can be viewed/downloaded at .3000 RESEARCH DRIVE, RICHARDSON, TX 75082 | 800.222.0193 | 469.624.8000 | +1.469.624.7400 | fax 469.624.7153AMX (UK) LTD, AMX by HARMAN - Unit C, Auster Road, Clifton Moor, York, YO30 4GD United Kingdom • +44 1904-343-100 • /eu/5123557 REV: F。
AM335x通用EVM硬件用户指南AM335x通用EVM硬件用户指南本文档介绍了AM335x评估模块（EVM）（__3358）这是基于德州仪器AM335x处理器的硬件体系结构。
该EVM通常也被称为AM335x通用（GP）EVM。
AM335x通用EVM是一个独立的测试，开发和评估模块系统，它使开发人员能够编写周围的AM335x处理器子系统的软件和硬件开发。
已经可用的EVM板的基础上，为开发人员提供了所需的基本资源最通用的类型的项目，包括作为主处理器的AM335x AM335x子系统的主要内容。
此外，额外的，“典型的”外围设备内置的的EVM如存储器，传感器，LCD，以太网PHY等，使未来的系统可以模拟快速显着的额外的硬件资源。
以下各节提供有关EVM的更多细节。
AM335x通用EVM的系统视图是由底板，子板，液晶显示板叠放在一起，通过标准的通孔连接器连接。
请参阅下面的图片的EVM。
图1：AM335x通用EVM图2：的AM335x底板底查看AM335x完整的通用EVM被划分在三个不同的电路板的模块化。
GP EVM包括基板（处理器和主电源），子板（外围设备）和液晶显示板（LCD和触摸屏）。
图3：AM335x的EVM系统板图处理器__59ZCZ处理器是此EVM的中央处理器。
在黑板上的所有资源环绕__59处理器提供的硬件和软件开发能力。
请参阅的__59数据表和TRM的处理器的详细信息。
有系统的配置信号，__，也可以设置在EVM上AM335x处理器定义一些启动参数。
有关详细信息，请参阅“配置/设置”一节。
EVM有几个时钟，支持AM3359处理器。
为处理器的主时钟是来自从24MHz晶体。
片上振荡器的AM3359产生基准时钟，后续的模块需要在AM3359处理器的时钟。
一个32kHz的时钟RTC的AM3359是来自一个32kHz的晶体在黑板上。
SYS_RESETn是运行多个外设和的AM335x其中执行这些外围设备的复位信号。
V2426A SeriesIntel®3rd Gen Core™CPU,EN50155railway computer with2mini PCIe expansion slotsFeatures and Benefits•Intel Celeron/Core i7processor•2peripheral expansion slots for various I/O,WLAN,mini-PCIe expansionmodule cards•Dual independent DVI-I displays•2Gigabit Ethernet ports with M12X-coded connectors•1SATA connector and1CFast socket for storage expansion•M12A-coded power connector•Compliant with EN50121-4•Complies with all EN50155mandatory test items1•Ready-to-run Debian7,Windows Embedded Standard7,and Windows10Embedded IoT Enterprise2016LTSB platforms•-40to70°C wide-temperature models available•Supports SNMP-based system configuration,control,and monitoring(Windows only)CertificationsIntroductionThe V2426A Series embedded computers are based on the Intel3rd Gen processor,and feature4RS-232/422/485serial ports,dual LAN ports,3 USB2.0hosts,and dual DVI-I outputs.In addition,the V2426A Series computers comply with the mandatory test items of the EN50155standard, making them suitable for a variety of industrial applications.The dual megabit/Gigabit Ethernet ports with M12X-coded connectors offer a reliable solution for network redundancy,promising continuous operation for data communication and management.As an added convenience,the V2426A computers have6DIs and2DOs for connecting digital input/output devices.In addition,the CFast socket,SATA connector,and USB sockets provide the V2426A computers with the reliability needed for industrial applications that require data buffering and storage expansion.Moreover,the V2426A computers come with2peripheral expansion slots for inserting different communication modules(2-port CAN module,or HSDPA,GPS,or WLAN module),an8+8-port digital input/output module,and a2-port serial module,giving greater flexibility for setting up different industrial applications at field sites.Preinstalled with Linux Debian7or Windows Embedded Standard7,the V2426A Series provides programmers with a friendly environment for developing sophisticated,bug-free application software at a low cost.Wide-temperature models of the V2426A Series that operate reliably in a-40 to70°C operating temperature range are also available,offering an optimal solution for applications subjected to harsh environments.1.This product is suitable for rolling stock railway applications,as defined by the EN50155standard.For a more detailed statement,click here:/doc/specs/EN_50155_Compliance.pdfAppearanceFront View Rear ViewSpecificationsComputerCPU V2426A-C2Series:Intel®Celeron®Processor1047UE(2M cache,1.40GHz)V2426A-C7Series:Intel®Core™i7-3517UE Processor(4M cache,up to2.80GHz) System Chipset Mobile Intel®HM65Express ChipsetGraphics Controller Intel®HD Graphics4000(integrated)System Memory Pre-installed4GB DDR3System Memory Slot SODIMM DDR3/DDR3L slot x1Supported OS Linux Debian7Windows Embedded Standard7(WS7E)32-bitWindows Embedded Standard7(WS7E)64-bitStorage Slot 2.5-inch HDD/SSD slots x1CFast slot x2Computer InterfaceEthernet Ports Auto-sensing10/100/1000Mbps ports(M12X-coded)x2Serial Ports RS-232/422/485ports x4,software selectable(DB9male)USB2.0USB2.0hosts x1,M12D-coded connectorUSB2.0hosts x2,type-A connectorsAudio Input/Output Line in x1,Line out x1,M12D-codedDigital Input DIs x6Digital Output DOs x2Video Output DVI-I x2,29-pin DVI-I connectors(female)Expansion Slots2peripheral expansion slotsDigital InputsIsolation3k VDCConnector Screw-fastened Euroblock terminalDry Contact On:short to GNDOff:openI/O Mode DISensor Type Dry contactWet Contact(NPN or PNP)Wet Contact(DI to COM)On:10to30VDCOff:0to3VDCDigital OutputsConnector Screw-fastened Euroblock terminalCurrent Rating200mA per channelI/O Type SinkVoltage24to30VDCLED IndicatorsSystem Power x1Storage x1LAN2per port(10/100/1000Mbps)Serial2per port(Tx,Rx)Serial InterfaceBaudrate50bps to921.6kbpsFlow Control RTS/CTS,XON/XOFF,ADDC®(automatic data direction control)for RS-485,RTSToggle(RS-232only)Isolation N/AParity None,Even,Odd,Space,MarkData Bits5,6,7,8Stop Bits1,1.5,2Serial SignalsRS-232TxD,RxD,RTS,CTS,DTR,DSR,DCD,GNDRS-422Tx+,Tx-,Rx+,Rx-,GNDRS-485-2w Data+,Data-,GNDRS-485-4w Tx+,Tx-,Rx+,Rx-,GNDPower ParametersInput Voltage12to48VDCPower Connector M12A-coded male connectorPower Consumption 3.78A@12VDC0.96A@48VDCPower Consumption(Max.)47W(max.)Physical CharacteristicsHousing AluminumIP Rating IP30Dimensions(with ears)275x92x154mm(10.83x3.62x6.06in)Dimensions(without ears)250x86x154mm(9.84x3.38x6.06in)Weight3,000g(6.67lb)Installation DIN-rail mounting(optional),Wall mounting(standard) Protection-CT models:PCB conformal coating Environmental LimitsOperating Temperature Standard Models:-25to55°C(-13to131°F)Wide Temp.Models:-40to70°C(-40to158°F) Storage Temperature(package included)-40to85°C(-40to185°F)Ambient Relative Humidity5to95%(non-condensing)Standards and CertificationsEMC EN55032/24EMI CISPR32,FCC Part15B Class AEMS IEC61000-4-2ESD:Contact:6kV;Air:8kVIEC61000-4-3RS:80MHz to1GHz:20V/mIEC61000-4-4EFT:Power:2kV;Signal:2kVIEC61000-4-5Surge:Power:2kVIEC61000-4-6CS:10VIEC61000-4-8PFMFRailway EN50121-4,IEC60571Railway Fire Protection EN45545-2Safety EN60950-1,UL60950-1Shock IEC60068-2-27,IEC61373,EN50155Vibration IEC60068-2-64,IEC61373,EN50155DeclarationGreen Product RoHS,CRoHS,WEEEMTBFTime304,998hrsStandards Telcordia(Bellcore),GBWarrantyWarranty Period3yearsDetails See /warrantyPackage ContentsDevice1x V2426A Series computerInstallation Kit1x wall-mounting kitDocumentation1x document and software CD1x quick installation guide1x warranty cardDimensionsOrdering InformationModel Name CPU Memory(Default)OS CFast(CTO)Backup CFast(CTO)SSD/HDD Tray(CTO)PeripheralExpansionSlotsOperatingTemp.ConformalCoatingV2426A-C2Celeron1047UE4GB1(Optional)1(Optional)1(Optional)2-25to55°C–V2426A-C2-T Celeron1047UE4GB1(Optional)1(Optional)1(Optional)2-40to70°C–V2426A-C2-CT-T Celeron1047UE4GB1(Optional)1(Optional)1(Optional)2-40to70°C✓V2426A-C7Core i7-3517UE4GB1(Optional)1(Optional)1(Optional)2-25to55°C–V2426A-C7-T Core i7-3517UE4GB1(Optional)1(Optional)1(Optional)2-40to70°C–V2426A-C7-CT-T i7-3517UE4GB1(Optional)1(Optional)1(Optional)2-40to70°C✓V2426A-C2-W7E Celeron1047UE4GB8GB1(Optional)1(Optional)2-25to55°C–V2426A-C2-T-W7E Celeron1047UE4GB8GB1(Optional)1(Optional)2-40to70°C–V2426A-C7-T-W7E i7-3517UE4GB8GB1(Optional)1(Optional)2-40to70°C–Accessories(sold separately)Battery KitsRTC Battery Kit Lithium battery with built-in connectorCablesCBL-M12XMM8PRJ45-BK-100-IP67M12-to-RJ45Cat-5E UTP gigabit Ethernet cable,8-pin X-coded male connector,IP67,1mCBL-M12(FF5P)/Open-100IP67A-coded M12-to-5-pin power cable,IP67-rated5-pin female M12connector,1mA-CRF-RFQMAM-R2-50Wi-Fi Extension Cable QMA(male)to SMA(male)adapter with50cm cable x1A-CRF-QMAMSF-R2-50Cellular Extension Cable QMA(male)to SMA(female)adapter with50cm cable x1A-CRF-CTPSF-R2-50GPS Extension Cable TNC to SMA(female)adapter with50cm cable x1ConnectorsM12A-5PMM-IP685-pin male circular threaded D-coded M12USB connector,IP68M12X-8PMM-IP678-pin male X-coded circular threaded gigabit Ethernet connector,IP67M12A-5P-IP68A-coded screw-in sensor connector,female,IP68,4.05cmM12A-8PMM-IP678-pin male circular threaded A-codes M12connector,IP67-rated(for field-installation)Power AdaptersPWR-24270-DT-S1Power adapter,input voltage90to264VAC,output voltage24V with2.5A DC loadPower CordsPWC-C7AU-2B-183Power cord with Australian(AU)plug,2.5A/250V,1.83mPWC-C7CN-2B-183Power cord with two-prong China(CN)plug,1.83mPWC-C7EU-2B-183Power cord with Continental Europe(EU)plug,2.5A/250V,1.83mPWC-C7UK-2B-183Power cord with United Kingdom(UK)plug,2.5A/250V,1.83mPWC-C7US-2B-183Power cord with United States(US)plug,10A/125V,1.83mWall-Mounting KitsV2400Isolated Wall Mount Kit Wall-mounting kit with isolation protection,2wall-mounting brackets,4screwsStorage KitsFK-75125-02Storage bracket,4large silver screws,4soft washers,4small sliver bronze screws,1SATA powercable,4golden spacers(only for the V2406and V2426)Expansion ModulesEPM-DK022mini PCIe slots for wireless modules,-25to55°C operating temperatureEPM-DK03GPS receiver with2mini PCIe slots for wireless modules,-25to55°C operating temperatureEPM-30322isolated RS-232/422/485ports with DB9connectors,-40to70°C operating temperatureEPM-31122isolated CAN ports with DB9connectors,-25to55°C operating temperatureEPM-34388DIs and8DOs,with3kV digital isolation protection,2kHz counter,-40to70°C operating AntennasANT-GPS-OSM-05-3M BK Active GPS antenna,26dBi,1572MHz,L1band antenna for GPSANT-LTEUS-ASM-01GSM/GPRS/EDGE/UMTS/HSPA/LTE,omni-directional rubber duck antenna,1dBiANT-WDB-ARM-02 2.4/5GHz,omni-directional rubber duck antenna,2dBi,RP-SMA(male)ANT-LTE-ASM-02GPRS/EDGE/UMTS/HSPA/LTE,omni-directional rubber duck antenna,2dBiANT-WCDMA-AHSM-04-2.5m GSM/GPRS/EDGE/UMTS/HSPA,omni-directional magnetic base antenna,4dBiWireless Antenna CablesA-CRF-MHFQMAF-D1.13-14.2Digital Interface Mini card internal antenna with QMA connector x1,locking washer x1,O-ring x1,nutx1DIN-Rail Mounting KitsDK-DC50131DIN-rail mounting kit,6screwsWireless PackagesEPM-DK3G Package Gemalto PHS8-P3G mini card with digital interface,internal antenna,installation bracket,screws,locking washers,O-rings,nuts,and thermal padEPM-DK Wi-Fi Package SprakLAN WPEA-121N Wi-Fi mini card with digital interface,internal antenna,installation bracket,screws,locking washers,O-rings,nuts,and thermal padEPM-DK LTE-EU Package Gemalto PLS8-E LTE mini card with digital interface,internal antenna,installation bracket,screws,locking washers,O-rings,nuts,and thermal padEPM-DK LTE-US Package Gemalto PLS8-X LTE mini card with digital interface,internal antenna,installation bracket,screws,locking washers,O-rings,nuts,and thermal padWireless Antenna Packages3G Antenna Package3G external antenna with QMA(male)to SMA(female)adapter and50-cm cables x2,3G externalantenna with SMA connectors x2,cellular extension cableLTE-US Antenna Package LTE-US external antenna with QMA(male)to SMA(female)adapter and50-cm cables x2,LTE-USexternal antenna with SMA connector x2,cellular extension cableLTE-EU Antenna Package LTE-EU external antenna with QMA(male)to SMA(female)adapter with50-cm cables x2,LTE-EUexternal antenna with SMA connectors x2,cellular extension cableWi-Fi Antenna Package External antenna with QMA internal cable,Wi-Fi extension cableGPS Antenna Package External antenna with TNC to SMA(female)adapter and a50-cm cable,SMA antenna(26dBi,1572MHz,L1band),GPS extension cable©Moxa Inc.All rights reserved.Updated Jan22,2020.This document and any portion thereof may not be reproduced or used in any manner whatsoever without the express written permission of Moxa Inc.Product specifications subject to change without notice.Visit our website for the most up-to-date product information.。
引子：中星9号接收机全4类芯片：海尔（Hi2023，Hi2023E），华亚HTV903(F)，国芯（GX3001，GX6121 ），阿里（ALiM3330E）的,等.为了避免刷成砖头，请认真参考以下内容！硬件准备：万用电表。
串口刷机板（TTL转接板。
可以自制，现成的也需要自制各种联机插线），标准串口延长线（用于使用标准9芯串口的接收机）万用电表：世人皆知。
用于判断各类接收机升级数据接口各引脚功能。
与电脑连接硬件：如果是标准9芯串口插头，直接使用标准串口延长线。
如果是4线或5线插排，请使用TTL转接板接入电脑的串口。
串口刷机板：自制的（成本6元左右，一个串口插头，max232集成电路，电解等），网上也有卖（大约12元钱+运费），自制电路图纸网上随便就可以找到，就是一个max232芯片以及一些辅助原件。
刷机板自身工作电源无法像图纸上那样从串口获得，可以从5线数据线的4脚得到14V然后经过78L05稳压供给。
但4线的数据接口标称3.3V（有些好像标5V的，未测），故本人从USB端口供电，直供5V，未使用耦合电路也是成功的，建议大家从USB端口直接供电。
只要找到一个退休的USB鼠标或摄像头剪下插头即可，非常实用。
该板连接接收机最终是3根线：公用地线，读数据，写数据。
用万用表判断4线或5线的数据接口：地线：不用说了吧？就是和高频头外壳直通的那根！呵呵！电源线：无论是多高的电压，电源相对于任何数据引脚都有相对较小的对地电阻，对地反向二极管导通性更明显。
数据读写线：两个引脚靠在一起，万用表实测电压为3.3V，而且紧靠接地脚。
至于哪个是输入那个是输出，应该看板子上的标注。
当然有些板子没有标注。
本人没动脑筋！做了两个数据插头（接地线总归在边上），通吃所有4或5线数据口。
刷机工具软件：海尔芯片2023或2023E使用ABS_Flasher_V1.6。
HTV903芯片使用serial（备份使用serial_dump，升级使用serial_app）。
