niagara中间件软件安装及测试文档

6测试6.1硬件测试用万用表测试左右扇面的24V+与24VG是否短路用万用表测试左右扇面的5V与5VG是否短路电源没有短路即可上电，若有短路，排查短路原因。

6.2软件测试6.2.1软件安装1、将U盘中的文件拷贝到一体机D盘下。

2、安装IndyTool v2.3.0，找到D:\一体机软件\R2000\IndyTool中的图标，双击进行安装。

3、将D:\一体机软件\F860光盘文件\app中的UHF.exe，UHFD.exe，UHFExample.exe，建立桌面快捷方式。

4、安装Niagara，运行Niagara4.1在D盘下建立文件夹作为安装Niagara路径4.2解压到’Niagara相关’文件夹下，参考Readme.txt文档。

4.3在D: \一体机软件\Niagara 相关\Niagara_AX_Developer-3.5.30中，双击图标，开始安装点击下一步，选yes,点下一步路径选择为D:\Niagara\Niagara-3.5.30，点下一步：选择select All选下一步：点下一步：点完成，用注册码激活软件将D:\一体机软件目录下的modules文件夹粘贴到D:\niagara\Niagara-3.5.30目录下的modules中；将D:\一体机软件目录下的demo文件夹覆盖D:\niagara\Niagara-3.5.30\stations目录下的demo 文件。

Niagara软件安装完毕。

5、安装Java JDK：找到D:\一体机软件\HerculesSetup.exe下的双击进行安装。

6、将D:\一体机软件\搜索配置设备创建到桌面。

6.2.2软件配置6.2.2.1路由器配置步骤：1、用一条网线将路由器的一个LAN口与电脑的网口连接。

2、打开电脑上的浏览器，输入http://192.168.1.1/后，得到如下页面：查看路由器上的用户名和密码（注意，该用户名和密码为出厂初始密码，在路由器背面有标注）输入到上图中。

一、实验目的1. 熟悉软件安装的基本流程和步骤。

2. 掌握不同类型软件的安装方法。

3. 学会使用软件卸载工具进行软件卸载。

4. 了解软件安装过程中可能遇到的问题及解决方法。

二、实验环境1. 操作系统：Windows 102. 硬件配置：Intel Core i5-8265U，8GB RAM，256GB SSD3. 软件环境：Microsoft Office、Adobe Photoshop、VMware Workstation等三、实验内容1. 安装Microsoft Office（1）下载Microsoft Office安装包（2）打开安装包，按照提示进行安装（3）选择安装类型，推荐选择自定义安装（4）选择安装路径，可根据个人需求修改（5）勾选需要安装的组件，如Word、Excel等（6）点击“安装”按钮，等待安装完成（7）安装完成后，启动Microsoft Office，进行激活2. 安装Adobe Photoshop（1）下载Adobe Photoshop安装包（2）打开安装包，双击运行安装程序（3）选择安装语言和地区（4）阅读许可协议，勾选同意（5）选择安装类型，推荐选择自定义安装（6）选择安装路径，可根据个人需求修改（7）勾选需要安装的组件，如Adobe Bridge、Adobe Camera Raw等（8）点击“安装”按钮，等待安装完成（9）安装完成后，启动Adobe Photoshop，进行激活3. 安装VMware Workstation（1）下载VMware Workstation安装包（2）打开安装包，双击运行安装程序（3）选择安装语言和地区（4）阅读许可协议，勾选同意（5）选择安装类型，推荐选择自定义安装（6）选择安装路径，可根据个人需求修改（7）勾选需要安装的组件，如虚拟网络适配器、虚拟光驱等（8）点击“安装”按钮，等待安装完成（9）安装完成后，重启计算机4. 使用软件卸载工具卸载软件（1）下载软件卸载工具，如IObit Uninstaller（2）打开软件卸载工具，选择要卸载的软件（3）点击“卸载”按钮，等待卸载完成（4）确认卸载完成后，重启计算机四、实验结果与分析1. 通过本次实验，成功安装了Microsoft Office、Adobe Photoshop、VMware Workstation等软件。

iCAP 7000 Qtegra 软件操作规程1.确认实验条件准备1.1室内湿度达到22~25度，湿度为40~65%,且保持恒定。

1.2打开排风设备, 确认稳压器供电稳定，零地电压<５v1.3确认氩气供应充足，分压调至0.6Ｍpa. 钢瓶内总压不小于1.5Ｍpa。

开大量流吹扫仪器半小时（若仪器长是间未开，建议大流量吹扫2小时以上）1.4确认冷却循环水水量充足，打开冷却循环水（确保仪器大量吹扫后开水机），查看水压，未点火之前为85psi.点火后约为75psi。

水温是否设定在20度1.5 安装好蠕动泵管，开泵，设定雾化器流量0.5l/min. 检查进样排废情况。

2.点燃等离子体2.1 打开仪器主机左侧电源开关,双击仪器控制软件 , 打开软件控制界面板. 如下图所示.2.2 确认所有联锁正常,如下图所示, 全部亮绿灯后, 方可以点燃等离子体.2.3 点击控制面板上的, 弹出如下对话框,按实际需要设定点火后的参数. Warm up仪器预热时间, 通常设定为15~20 minutes. Spectrometer Optimization光谱仪优化,建议勾选, Run performance Check 及perform Detection Limit Check为仪器性能检查, 日常测试可不勾选.若使用手动进样, 则将Use Manual Sampling 勾选上. 并设定wash time通常都设定为30s, 若测定样品比较容易残留管路, 可将值设大些, Uptake time 表示样品提升时间,根据进样管路长度设定,通常设定为30s.设置完成后,点击OK, 仪器开始自动预热,按软件提示,将样品管放出纯水中.约20min分钟后,仪器预热及光谱仪优化成功.软件提示success.如下图所示.检查log view （下图红框）中的光谱仪优化后的x,y 值, 要求分别控制在±3以内.2.4 若安装了新的炬管或炬管拆下清洗后重新安装，则需在分析样品前做炬管准直.点击控制面板中的torch alignment。

6测试6.1硬件测试用万用表测试左右扇面的 24V+与24VG 是否短路 用万用表测试左右扇面的 5V 与5VG 是否短路 电源没有短路即可上电，若有短路，排查短路原因。

6.2软件测试 6.2.1软件安装1、将U 盘中的文件拷贝到一体机 D 盘下。

2、安装 IndyTool V2.3.0，找到 双击进行安装。

3、将 一体机软件 \F860 光盘文件 \app 中的 UHF.exe , UHFD.exe , UHFExample.exe 桌面快捷方式。

4、安装 Niagara ，运行 Niagara 4.3 在 D: 一体机软件 \Niagara 相关 \Niagara_AX_Developer-3.5.30 中，一体机软件\R2000\lndyTool 中的图标 4.1在D 盘下建立文件夹作为安装Niagara 路径Readme.txt 文档。

图标，开始安装，建立 4.2解压 'Niagara 相关'文件夹下,点击下一步,Please read the folto^ing license agreen^enr End U?er License Agreement 曲也 1 反 2005 [M 曲 be updat&d from time by T ridiurri]IRIDIUM, INC. fTRIDIUM")HAS DEVELOPED A STAhOAFSDIZED ARCHITECTURE AHD RELATED SOFTWARE FOR IMTE FrCON ME CUN G DEVICES AND CONTROLLERS TRIDILJH IS WILLING TO PR0VID "LIMITED LICENSE 0FTH EAECHITE CTURE AND SOFTWARE (THE "NIAGARA FRAMEWORK") TO ?0U ONLY ON THE COMDITION THAT YOU ACCEPT ALL OF THE TERMS IN THIS AGREEMENT.PLEASE READ THE TERMSAND CONDITIONS OF THIS AGREEMENT CAREFULLY BEFORE OLICKING ON THE "I ACCEPT J1 BUTTON. BY COCKING ON THE"I ACCEPT" BUTTON YOU ACKNOWLEDGE THAT YOU HAVE FiEAD THIS AGREEMENT AND AGREE TO SE BOUND BY ITS TERMSAND CONDITIONS.匚 LI 匚 <DN THED Q you ^Gtept thi? ^areerrient?选yes,点下一步、• Papered(Wiamra、一/ OF»!AMEWOPlt fcInstallationWefcome to the NidgaraAXuevelopBr Package 15 30 Installation F\oca?$This program will in si alfthe Niagara 朋 D eveloper 3.5.30 software orto voui computer.guild 3L5.30 MOct2(T10下一古no ＞取消License Agreement＜上一母広）下一母的）＞惡消gmpeul耆Apu id圧laqiar^'AK Deve toper Pac.*rawered byFRAMEWORK "3D^lFiation' FolderD : VN iagaraVH iag ara-3.5 30DefaultQtoupjse...Space Required Space A.v^4able* T his insknee of WotkHace 朋 will be iced 日$ an installation tool (10394G冏』Install DceuFrtferthtiarr(67423 旬路径选择为 D:\Niagara\Niagara-3.5.30，点下一步:选择 select AllSelect Install Location<上一步(B)下一步01) >啟消Poiverecf byaraFRAMEWORK'Select Language PackagesLexicon*口 Albanicin (sq |O Arabic 同 □[be]O Eitilgsrian (bg] 口匚制胡an [ca]TAdditionel Space Required<上一步下一步00 >职消AX D^el$E€1 Effi也PS8CO0Select the languaoe packages 5JOU wish to install:0K Select AllWlagaP? AX Devefoper Pa^l^e 3320尹一• Powe/erf 即(miamra冲 AM 出 ORIE +C 上一步(I)下一步(K) > 陋消选下一步:厂、 ■ fotvered by(n)iamra*o 咖阳Select Options点下一步:s e s a e询pum S G 6E E82w k * Iridal Starf Menu ShoftcuU * InaJtal desktop Shartcuts<上一步下一步00 > 軀消AXSelect Language PackagesguHPBUI 舌wacnluSelect lhe language packages you 刚弗 to mtaikAddlional SpaceReq Gired:609 KCleat All、 • fotvered by(n )iamrct丿 o FRAMEWORK ~NiagvFd 程' Developer Package 3.5.30 Ir^tallabon Complete! Would you to?* Lacnch ^A/oikbencIi"Install and Stait Phtlorm DaemonFinish Installi点完成，用注册码激活软件将一体机软件目录下的modules文件夹粘贴到D:\niagara\Niagara-3.5.30目录下的modules中；将一体机软件目录下的 文件。

中间件Niagara的使用说明文档中间件Niagara的使用说明一、启动Workbench1.启动后台服务2.启动控制台3.打开控制台后，输入WB启动workbench二、打开workbench1.打开plantform输入电脑的用户名和密码（本机或者要访问的电脑），点击OK双击Application Director，打开应用向导显示station列表选择demo，点击start，启动，会看到demo状态变化“Idle Starting Running”说明：每台电脑可以同时启动多个station，前提是它们所使用的端口不能相同。

2.打开已有的Station相应的Station就被启动，图标显现颜色。

界面中最重要的几个部分导航栏，调色板和主面板说明：导航栏是树形的结构，可以经由过程双击的办法来挑选要浏览的界面调色板用来选择不同的组件主面板是显示station内容的地方在导航栏或者主面板，都可以通过双击来打开想要浏览的页面二、新建Station点击Tools-New Station输入该站点的名称，点击Next输入用户名、密码、端口号，点击Finish，即完成建好之后，在platform下的Application director-station上右键，可以启动该station。

station启动后，可以经由过程file-open-open station来打开正在运行的station。

如许，你就会在platform下面的节点处看到这个station了。

说明：station其实是在后台运行的，前面所看到的一切，都是通过workbench远程连接而展示出来形象化界面。

所以，workbench关掉了，不会影响到后台station的运行。

除非通过application director发送命令将该station停止。

三、建立数据采集1.新建文件夹在导航栏config上右键，New Folder新建文件夹，输入名称，点击ok在导航栏就会显示新建的文件夹2.新建view在选定的文件夹图标上点击右键，views new view输入相应的名称，点击ok出现图形视图的编纂界面3.新建数据点有四种数据类型：布尔型，数字型，枚举型，字符串型。

Installation GuideMicro Focus575 Anton Blvd., Suite 510Costa Mesa, CA 92626Copyright © Micro Focus 2013. All rights reserved. Portions Copyright © 1992-2009 BorlandSoftware Corporation (a Micro Focus company).MICRO FOCUS, the Micro Focus logo, and Micro Focus product names are trademarks orregistered trademarks of Micro Focus IP Development Limited or its subsidiaries or affiliatedcompanies in the United States, United Kingdom, and other countries.BORLAND, the Borland logo, and Borland product names are trademarks or registeredtrademarks of Borland Software Corporation or its subsidiaries or affiliated companies in theUnited States, United Kingdom, and other countries.All other marks are the property of their respective owners.2013-05-28iiContentsIntroduction (4)System Requirements and Prerequisites (4)Hardware Requirements (4)Platform Support (4)Adobe Flex Support (5)Administrator Privileges (5)Items Included with Silk4NET Web Edition (5)Licensing Information (6)Installing Silk Test (7)Installation Prerequisites (7)Resetting the TEMP Environment Variable (7)Installing Silk4NET Web Edition (7)Installing the Silk4NET Visual Studio Plug-in Manually (9)Uninstalling Silk Test (9)Contents | 3IntroductionThis Help provides all the information you need to install and uninstall Silk Test. It describes hardware andsoftware requirements and details the various setup options.System Requirements and PrerequisitesThe following section identifies the system requirements for installing and running Silk Test.Hardware RequirementsWe recommend the following hardware requirements:Platform SupportPlatformsSilk Test 14.0 is designed to run on the following platforms:•Microsoft Windows XP SP3•Microsoft Windows Vista SP2*•Microsoft Windows 7•Microsoft Windows 7 SP1•Microsoft Windows 8Technology Domains and BrowsersFor the Open Agent, Silk Test 14.0 supports all applications that use the following browsers or aredeveloped in:Note: You can only test Adobe Flex applications with Silk4NET if you have a Web plus Flex licensefor Silk4NET. For additional information on the licensing modes, see Licensing Information.* Indicates a rapid release version of a browser. Such versions have a short product life-cycle and arefrequently replaced by newer versions. Silk Test supports rapid release versions as long as the issuing4 | Introductionvendor supports them. This means that the next Silk Test version will probably not continue to support theindicated versions, but might support newer versions.Visual Studio EnvironmentYou can integrate Silk4NET in Visual Studio 2010 Professional or later.Adobe Flex SupportNote: You can only test Adobe Flex applications with Silk4NET if you have a Web plus Flex licensefor Silk4NET. For additional information on the licensing modes, see Licensing Information.Note: Silk Test does not support testing child domain technologies, including Adobe Flex, for Webapplications running in Google Chrome.Silk Test supports Adobe Flash Player 10 or later.Administrator PrivilegesYou must have local administrator privileges to install Silk Test. Once Silk Test is properly installed, youmust also have administrator privileges in order to perform the following tasks:•Run Silk Test Classic.•Configure a database for Silk Test Workbench.Items Included with Silk4NET Web EditionWhen you install Silk4NET, the following items are available:•Silk4NET•Product Notification Service - This application resides in the system tray and will check for updates at a configurable interval.•Online Help topicsAccess the help from within each product from the Help menu.•Release NotesFor information about new features, supported platforms and versions, known issues, and work-arounds, refer to the Silk Test Release Notes, available from /productdoc.aspx.•Online tutorials from /productdoc.aspxYou must have Adobe Acrobat Reader™ to view PDF documents.•Sample applications that you can access online•Adobe Flex sample applicationsAccess Flex sample applications at /flex/SilkTest14.0/index.html.•Insurance Company Web applicationYou can access the Web application at: /InsuranceWebExtJS/.Introduction | 5Licensing InformationUnless you are using a trial version, Silk Test requires a license.The licensing model is based on the client that you are using and the applications that you want to able totest. The available licensing modes support the following application types:Note: To use a Full or a Premium license, you require a different setup package. The information inthis document applies only to the Web Edition of Silk4NET. For a detailed overview of the capabilitiesof the Full and Premium offering, see Release Notes.6 | Licensing InformationInstalling Silk TestThis section explains the setup options that are available when installing Silk Test.Installation PrerequisitesBefore installing Silk Test, verify the following information:•Your user account possesses local administrator privileges.Resetting the TEMP Environment VariableIf your Windows TEMP environment variable does not point to a valid directory, an error message isdisplayed. To successfully install Silk Test, your TEMP environment variable must point to a valid directory.1.Choose Start > Settings > Control Panel.2.Double-click System.3.Click the Advanced tab, and then click Environment Variables.4.Under User Variables or System Variables, double-click the TEMP variable.5.Enter a valid directory, and then click OK.6.Restart the Silk Test installation by double-clicking the EXE file.Installing Silk4NET Web EditionThe Silk4NET Visual Studio plug-in enables you to create or C# test scripts directly in VisualStudio. When you install Silk4NET, Silk Test Recorder and the Open Agent are also installed. Silk TestRecorder enables you to record tests rather than manually coding them. The Open Agent is required to runSilk4NET and Silk Test Recorder.1.Locate and double-click the Silk Test executable file.If you have a Silk Test CD, insert your CD. If the setup program does not start automatically, manuallystart the Silk Test setup program by choosing Start > Run and entering <cddrive>:\setup.exe.Note: If your Windows TEMP environment variable does not point to a valid directory, an errormessage is displayed. To successfully install Silk Test, your TEMP environment variable mustpoint to a valid directory.The InstallAnywhere wizard opens.2.If you previously installed a version of Silk Test, click Uninstall and then click Next to remove allinstalled features.You must uninstall any earlier versions before you install a new version.3.Click Next.The License Agreement opens.4.Read the license agreement carefully. If you accept the terms of the agreement, click I accept theterms of the License Agreement.5.Click Next.The Choose Install Folder page opens.6.To change the default installation directory, perform the following steps:a)Click Choose. The Browse For Folder dialog box opens.Installing Silk Test | 7b)Specify the folder in which you want to install Silk Test, and then click OK to return to the ChooseInstall Folder page.The location displays in the Where Would You Like to Install? text box.7.Click Next.8.Specify whether you want to create Windows firewall exceptions.Note: This step is only available for Windows XP, Windows Vista, Windows 7, and WindowsServer 2008.a)Click one of the following option buttons:•Yes – To have setup create firewall exceptions for all Silk Test executable files. As a result, you are not prompted to block or allow the executable files when you launch them.•No – To be prompted when you launch the Silk Test executable file.b)Click Next.9.Review the provided information and perform one of the following steps:•To change any settings, click Previous to return to the appropriate page.•If you are satisfied with the settings, click Install to start the installation process.Tip: If a message appears stating that there is not enough space while files are copying, redefine the TEMP area to a drive that contains more space. The installer uses the TEMP area forunzipping files. For example, if your TEMP area is d:\temp and you are installing to e:\SilkTest, the E drive may contain enough space for the installation, but the D drive is thelimiting factor.The status bar provides information about the installation process. Upon completion, the Choose Licensing Mode page opens.10.Click one of the following option buttons:•Evaluation Installs an evaluation version of Silk Test, which enables you to explore the full product functionality for 45 days.•Full version – Installs an unrestricted version of Silk Test, which requires a license.11.To install the license file, perform the following steps:a)Click Configure your license server and then click Next.The license utility checks your local system for the existence of SilkMeter license serverconfiguration files. If the files are found, the configuration and type of license server are displayed and used for licensing. If no configuration data is found, the Select SilkMeter License Server page is displayed with the default settings.b)From the Application list box, select Silk Test as the application you are licensing.c)Click one of the following option buttons:Using local or remote server In the License Server Host text box, type the name of the computer on which SilkMeter is installed. Do not change the default port number, 5461, unless your network administrator has defined a different port. Click Apply to generate your license server configuration. Click Test Connection to verify that a SilkMeter server is accessible on the specified host and port. Testing the connection to the license server might fail during installation as required system libraries, which are installed later with the software package, might not yet be available.Note: In some cases, specifying the simple name of the license server inthe License Server Host text box, such as licenseserver, might notwork. A message box stating there is no license serverrunning on the hostname you specified opens. To resolve this issue, specify the hostname by using a fully qualified name, such as.8 | Installing Silk TestNot using server (standalone)Runs SilkMeter standalone. You are prompted to import a SilkMeter license file. Click Yes and specify the location of your license file.d)Click Close.Fastpath: A working network connection is required when running Silk Test with a remoteSilkMeter license server. If you need to verify that the network is working, choose Start > Run,and then type ping localhost or ping <license server name>, or open a commandprompt and type either of those commands.The Install Complete page opens.12.Click Done.13.Restart Visual Studio if it was running when you performed the Silk4NET installation.When installation completes, a menu option appears for Silk4NET and the Silk4NET project is availablefrom the Installed Templates list.Installing the Silk4NET Visual Studio Plug-in Manually The Silk4NET Visual Studio plug-in enables you to create Visual Basic or C# test scripts directly in VisualStudio. You can install the Silk4NET Visual Studio plug-in when you install Silk Test using the Silk Testinstallation wizard.Use this procedure:•If you upgrade your version of Visual Studio after you install the Silk4NET plug-in.1.Execute the file MicroFocus.SilkTest.Silk4NET.vsix in the folder <Silk Testinstallation directory>\ng\Silk4NET.By default the location is C:\Program Files\Silk\Silk Test\ng\Silk4NET.2.In Visual Studio, verify that the menu option for Silk4NET appears and that the Silk4NET project isavailable from the Installed Templates list.Uninstalling Silk TestWhen you install a new version of Silk Test, the wizard prompts you to uninstall any existing versions ofSilk Test. You can also uninstall Silk Test from the programs menu at any time.1.Click Start > Programs > Silk > Silk Test > Administration > Silk Test Uninstall. TheInstallAnywhere wizard opens the Uninstall Silk Test <version> page.2.To remove all files from the installation directory, check the Remove all files check box.If you check this check box, the following items or folders are removed:•The Access database and samples•The contents of [AppDATA]/Silk/Silk TestFor example, on Windows 7 this directory is located at: C:\Users\[username]\AppData\Roaming\Silk\Silk Test•The contents of [commonAppData]/Silk/Silk TestFor example, on Windows 7 this directory is located at: C:\ProgramData\Silk Test•The contents of [commonAppData]/Silk/Silk Test WorkbenchFor example, on Windows 7 this directory is located at: C:\ProgramData\Silk TestWorkbenchInstalling Silk Test | 93.Click Uninstall. If any files were not removed, a list of the files is provided.4.Click Done.10 | Installing Silk TestIndexAadministrator privileges 5GGreen Mountain Outpost (GMO) application location 5Iinstallingoverview 4process overview 7Silk4NET 7, 9Insurance Company Web applicationlocation 5Llicensingavailable license types 6Ooverviewinstalling 4items installed 5Ssample applicationslocation 5Silk4NETinstalling 7installing manually 9TTEMP environment variable 7UuninstallingSilkTest 9VVisual Studio plug-ininstalling 7Index | 11。

Niagara讲解要点1、引⾔随着当今社会的⾼速发展，嵌⼊式、智能设备和系统已经遍及我们的周围，它们隐藏在我们⼯作和⽣活的各个⾓落，负责从环境控制（温度、湿度、空⽓质量、照度），到安全（消防安防报警、通道控制、视频监视），到测量（⽔、电、燃⽓），到服务（电梯、垃圾处理，热⽔器），甚⾄是我们所使⽤的商品的⽣产线上。

智能设备和系统越来越多的影响着我们的世界。

如今的设备的智能化越来越⾼，能⼒也越来越强，但是我们真正发挥出它们的所有能⼒了吗？它们告诉我们它们在做什么了吗？它们检测到某些情况了吗？它们决定做什么或不做什么吗？它们知道彼此的存在并相互配合了吗？现实是这些嵌⼊式的设备，不像PC 或者Server，可以⽀持图形操作系统的各种应⽤，并不容易相互通信，嵌⼊式设备⼤都使⽤成百上千的不同的，⾮IP 的通信协议，其中只有⼀部分被认定为标准。

和我们的PC 和Server 不同的是，⽤户投资这些设备会保留10 到15 年，⽽⾮3 到 5 年。

也就是说这些设备会跟随我们相当长的时间，如何在不更换这些设备的情况下，让它们协调⼯作并且更好的管理是摆在每⼀个集成商和⽤户⾯前的关键问题。

正如“团结就是⼒量”，当信息被分享并相互关联时，智能化的效果就会⼤⼤提升，麦特卡夫定律（互联⽹奠基⼈）正好说明了这⼀点，“ ⽹络价值同⽹络连接数量的平⽅成正⽐”，如何让各种智能设备连接IP ⽹络并融⼊上层的应⽤系统，也就是我们所提出的创建智能设备的各种应⽤，就变得⾄关重要。

Tridium 公司所研发的Niagara AX 平台正是设计⽤于解决设备连接应⽤的软件框架平台。

2、Niagara AX 简介NiagaraAX 是⼀种应⽤框架，或者说是软件框架，特别设计⽤于应对智能设备所带来的各种挑战，包括设备连接到企业级的应⽤，⽀持互联⽹的产品和基于互联⽹⾃动化系统的开发。

应⽤框架是⼀个软件⼯程中的概念，不同于普通的软件，它是⽤于实现某应⽤领域通⽤完备功能的底层服务，使⽤这种框架的编程⼈员可以在⼀个通⽤功能已经实现的基础上开始具体的产品和系统开发。

基于Modbus tcp协议通讯的红外控制器与Niagara通讯手册1、通讯建立1) 展开“Station→Config”，双击“Drivers”文件夹，在右侧弹出的“Drivers Manager”窗口点击“New”；2) 选择“Modbus Tcp Network”，点击“OK”；3) 点击“OK”；4) 双击“Drivers”下新建好的设备，“Database”页面点击“New”；5) 点击“OK”；6) 将名称修改为“红外控制器”，IP Address修改为“192.168.0.104”，Port（端口）改成“502”，点击“OK”；7) 点击“OK”；2、数据点的创建1) 展开“Modbus Tcp Network”设备下的“红外控制器”，双击“Points”；2) 右上角点击“Modbus Tcp Device Manager”，选择“Wire Sheet”；3) 点击按钮，选择“Palette”；4) 点击按钮；5) 输入关键字“mod”查询，选择“modbusTcp”，点击“OK”；6) 展开“Presets”文件夹，将“Modbus Client Preset Registers”拖到右侧页面中；7) 将名称修改为“空气净化器控制”；8) 将名称修改为“电视控制”；9) 将名称修改为“空调控制”；10) 将名称修改为“制冷控制”；11) 将名称修改为“制热控制”；12) 完成如下图；13) 双击打开“空气净化器控制”模块，修改starting address为100，Value为255，点击保存；注：其他模块参考“空气净化器控制”，将starting address一次改为101-104即可。

14) 选择空气净化器控制模块，右键选择“Actions”→“Write”，即可打开或关闭空气净化器注：其他模块参考“空气净化器控制”控制即可。

3、新建PX页面1) 右键“Drivers”，选择“Views→New View”；2) 在弹出的窗口将PX页面命名为“红外控制器”，点击“OK”；4、绘制组态页面1) 展开“红外控制器”下的“Points”文件夹，将该文件夹下的数据点拖入PX 页面；2) 在弹出的“Make Widgets”窗口选择“Actions”→“Write”，然后点击OK；3) 完成后如下图；4) 双击进入配置属性，修改text为“空气净化器控制”；5) 同样的方法创建其他模块即可。