不良现象中英对照表(Intel)

[replyview]不良现象中英文对照表1.缺件(MISSING PARTS) 28.脚未弯(PIN NOT BENT) 55.印章错误(WRONGSTAMPS)2.错件(WRONG PARTS) 29.缺盖章(MISSING STAMP) 56.尺寸错误(DIMENSION WRONG)3.多件(EXCESSIVE PARTS) 30.缺卷标(MISSING LABEL) 57.二极管坏(DIODE NG)4.短路(SHORT) 31.缺序号(MISSING S/N) 58.晶体管坏(TRANSISTOR NG)5.断路(OPEN) 32.序号错(WRONG S/N) 59.振荡器坏(X’TL NG)6.线短(WIRE SHORT) 33.卷标错(WRONG LABEL) 60.管装错误(TUBESWRONG)7.线长(WIRE LONG) 34.标示错(WRONG MARK) 61.阻值错误(IMPEDANCEWRONG)8.拐线(WIRE POOR DDRESS) 35.脚太短(PIN SHORT) 62.版本错误(REVWRONG)9.冷焊(COLD SOLDER) 36.J1不洁(J1 DIRTY) 63.电测不良(TEST FAILURE)10.包焊(EXCESS SOLDER) 37.锡凹陷(SOLDER SCOOPED) 64.版本未标(NONREV LEBEL)11.空焊(MISSING SOLDER) 38.线序错(W/L OF WIRE) 65.包装损坏(PACKING DAMAGED)12.锡尖(SOLDER ICICLE) 39.未测试(NO TEST) 66.印章模糊(STAMPSDEFECTIVE)13.锡渣(SOLDER SPLASH) 40.VR变形(VR DEFORMED) 67.卷标歪斜(LABELTILT)14.锡裂(SODER CRACK) 41.PCB翘皮(PCB PEELING) 68.外箱损坏(CARTONDAMAGED)15.锡洞(PIN HOLE) 42.PCB弯曲(PCB TWIST) 69.点胶不良(POOR GLUE)16.锡球(SOLDER BALL) 43.零件沾胶(GLUE ON PARTS) 70.IC座氧化(SOCKET RUST)17.锡桥(SOLDER BRIDGE) 44.零件脚长(PARTS PIN LONG) 71.缺UL卷标(MISSING UL LABEL)18.滑牙(SCREW LOOSE) 45.浮件(PARTS LIFT) 72.线材不良(WIRE FAILURE)19.氧化(RUST) 46.零件歪斜(PARTS TILT) 73.零件脚损坏(PIN DAMAGED)20.异物(FOREIGNER MATERIAL) 47.零件相触(PARTS TOUCH) 74.金手指沾锡(SOLDER ON GOLDEN FINGERS)21.溢胶(EXCESSIVE GLUE) 48.零件变形(PARTS DEFORMED) 75.包装文件错(RACKING DOC WRONG)22.锡短路(SOLDER BRIDGE) 49.零件损坏(PARTS DAMAGED) 76.包装数量错(PACKING Q’TY WRONG)23.锡不足(SOLDER INSUFFICIENT) 50.零件脚脏(PIN DIRTY) 77.零件未定位(PARTS UNSEATED)24.极性反(WRONG POLARITY) 51.零件多装(PARTS EXCESS) 78.金手指沾胶(GLUE ON GOLDEN FINGERS)25.脚未入(PIN UNSEATED) 52.零件沾锡(SOLDER ON PARTS) 79.垫片安装不良(WASHER UNSEATED)26.脚未出(PIN UNVISIBLE) 53.零件偏移(PARTS SHIFT) 80.线材安装不良(WIRE UNSEATED)27.脚未剪(PIN NO CUT) 54.包装错误(WRONG PACKING) 81. 立碑(TOMBSTONE)。

General Defect - 通用电器缺陷cord untied or irregularly tied电线未绑或绑的不规则exposed wires金属线外露brass wire in power cord exposed电源线的铜丝外露ground wire discontinuous地线间断burn down烧坏jam刮／卡死excessive noise噪音过多shock noise振动有噪音switch operated not smoothly开关不顺polarity reversed极性接反open circuited开路short circuited短路grounding continuity test failed接地失败Hi-pot test failed高压失败leakage current test failed漏电power supply dead无电源dielectric strength test failed介质强度测试失败current or wattage out ofspecification电流／电压不合规格live wire exposed火线外露General location - 电器通用缺陷位置jack插口AC-IN jack交流输入口DC-IN jack直流输入口socket插座socket cover插座盖plug插头plug foot插脚polarized plug极性插头coupling plug转化／耦合插头flat blade plug扁脚插头channel频道function key功能键nut螺母LCD液晶显示屏power LED indicator电源电子指示灯power cord电源线electrode plate电极片ON-Off switch开关adapter适配器transformer变压器remote control遥控器Lighting Fixture - 灯饰cold flow mark冷塑痕迹（拉痕）defective stamping冲压不良glass panel cut crooked玻璃切割弯曲glass panel out of square玻璃不规则（歪斜不直）gouge mark凿痕holes improperly drilled孔眼钻的不对insufficient plating电镀不足lamp stand tilted after assembled安装后灯站立倾斜machining mark车痕screw stripped缺螺纹poor porosity holes疏松多孔poor rolling edge卷边不良rough planting镀层粗糙（镀前未抛光清洗）seam mark exposed少锡漏缝spinning lines旋压线wrong finish表面处理错误obvious shrinkage or deformation on surface of plastic or metal parts 金属／塑料表面有明显缩水或变形grinding mark磨痕bulbs on holder poorly assembled(灯座上）灯泡安装不良plug rusted插头生锈figures poorly shaped成形不佳incorrect sequence of color彩灯顺序不对scratch on color bulbs彩灯刮花bulb can on light up灯泡不亮flash light no function闪光灯无功能abnormal noise in music box音乐盒内有异常噪音wrong music melody音乐曲调不对live and neutral wires short in circuit火线和中线短路bulbs too dim灯泡过于黯淡broken light bulbs灯泡破incorrect size, watt and style ofbulbs used灯泡尺寸，瓦数，款式不对design finish, color of lamp andshadenot according orSPEC(smoked,white,ect)灯，灯罩的款式，表面处理及颜色SPEC不符（有烟熏或发白等）design and color not consistence for all lamps of same style 同一款式灯之间的设计及颜色不对floor lamps cannot stand vertically with leaning or falling over 落地灯站立不直，有倾斜或翻倒shade cannot fit bulb properly(loose)灯罩于灯泡不配（太松）missing UL label on product缺UL标smoking from light bulb or otherelectrical areas灯泡内或其它用电区域冒烟overheating过热assembled parts not secure配件组装不牢固glass not secured in shade灯罩内玻璃固定不牢sharp edges on shade灯罩有锐边stained glass pieces not neatlyplaced on shade灯罩彩色玻璃排列不整齐cup shade灯罩font灯罩底盘baffle灯罩障板harp灯罩架arm灯臂bobeche灯杯bulb灯泡bulb holder灯座sconce陶瓷壁灯座socket灯头socket cover灯头盖socket cap灯头帽ceramic socket陶瓷灯头cluster灯簇cluster stem灯簇柱goose neck鹅颈frosted glass磨砂玻璃frosted glass dome磨砂玻璃圆顶glass decoration玻璃装饰glass shield玻璃罩head joint（灯与柱）的连杆upper stem/pole上柱middle stem/pole中柱lower stem/pole下柱hardware pack附件sleeve套管candle sleeve蜡烛套管hurricane cup飓风杯（蜡烛套下之小灯杯）snuffer蜡烛套盖latch门闸Lucite panel塑料透明挂片mirror panel挂镜片mounting hole安装孔mounting plate安装板nipple螺纹套管nut螺母pipe管道plastic ring塑料环plastic support塑料支架／架plug塞子／插头power supply cord电源线protective glass防护玻璃protective ring保护环reflective panel反光面reflector反光镜adjusting handle调节手柄anchor膨胀螺丝back plate背板beveled glass edge玻璃斜边brass channeling铜条brass coupling铜连接头canopy天房盖ceiling pan吸顶盘chain链条clip夹片cone圆锥／锥面cord cover护线盖cross bar一字板／十字板curved tubing旋转管（花饰）／弯管dimmer switch微调开关distributor配线盒electric phenolic电木圈finial顶纽relamping label换灯标签rolled edge滚边tightening knob紧固旋纽screw collar loop螺纹套圈吊环screw collar nut螺纹环螺母securing knob固定旋纽set screw固定螺丝green ground screw接地绿螺丝wire nut接线螺帽wood screw木螺丝spiral ball麻花螺线球rubber washer胶垫片steel washer铁垫片spacer垫圈insulation pad绝缘垫tab薄片diffuser散射片ventilation slots散惹槽switch box开关电线盒swivel转动接头wire connector电线连接器spoke轮辐track轨道／路轨tray托盘top plate顶板adaptor功能适配器fitter机械适配器polarity test极性测试grounding test接地测试endurance test耐力测试assembly test组装测试Hi-pot test高压测试TV Set - 电视机infra-red sensor红外线感应器rod antenna棒状天线antenna mounting bracket天线支架prop up stand可折叠支架external antenna jack外部天线插口earphone jack耳机插口screen荧光屏picture电视画面vertical hold control (V-hold)图象垂直调整speaker喇叭control door面板门band switch波段开关selector switch选择开关TV system switch电视系统选择开关channel NO. knob频道纽TV tuning knob电视频道调节组preset预设纽sleep knob睡眠纽mute knob消音纽brightness control knob亮度控制纽color control knob颜色控制纽contrast control knob对比度控制纽Auto-search knob自动搜索纽UHF tuning knob-UHF超高频旋转纽VHF tuning knob-VHF特高频旋转纽UHF channel indicator-VHF超高频道指示表VHF channel indicator-VHF特高频道指示表strain relief test failed张拉力测试失败smoke of fire during operation运转时冒火烟poor quality or peelingsilkscreen/hotstamp丝印／火印不良或引导剥落knob control poor assembly旋纽控制装配不良AFC or manual tuning no function自动频率控制或手工调谐无功能horizontal/vertical linearitymisalignment水平线／垂直线定线不准picture not center properly图象集中不当dead or dead on one channel（某一频道）失灵no picture/audio output/howling无图象／音频输出／有振鸣volume, tume&balance control intermittent, noisy, faulty 音量，音调和平衡控制功能间歇，有杂音，出错misoperation of remote control遥控器失灵stereo channels reverse立体声频道接反clock/timer/sleep set no function 时钟／计时器／睡眠状态设置无功能sound distortion , hum, buzz, rattleor vibration声音失真，嗡鸣，咔哒生或颤音speaker damaged/faulty causedsound distortion, hum, buzz, rattle or vibration 喇叭损坏或故障导致声音失真，嗡鸣，咔哒声或振鸣speaker connection in wrong phase喇叭接线相位不对LED/LCD display with segmentmissing, excessive or uneven segment LED/LCD显示屏缺划，多划或划不均piture/brighteness&contras no function or int 图象／亮度和对比度无功能或功能间歇TV/CATV selection no function电视／有线电视选择无功能external aerials, DC adaptor or other accessories inoperative/intermittent 外接天线，直流转接器或其它附件无功能／功能间歇damaged/cracked PCB&CRT印刷电路＆阴极射线管损／裂poor soldering, dry joint,components bridging焊接／干接／组件搭接不良sensitivity out of limit(audio/vidio)音频／视频灵敏度超限mute recall no function弱音器／重叫记忆无功能radio signal unstable无线电接收信号不稳定frequency drift/off alignment频率飘移／不准snow noise on picture >59Db 图象有雪花噪声干扰（高于59分贝）screen not stable图象不稳定auto power no function自动电源无功能out of focus or focus poor alignment焦点未对准channel off alignment频道偏差Audio products-CD/Radio/CassettePlayer - 音频产品／唱碟机／收音机／盒式录放机buzz轻微颤音hum嗡嗡声FM/AM/SM oscillation接收不稳定no station received接收不到电台off calibration接收偏离刻度no sound无声FＭ stereo no separation立体声无分离L/R channels reversed左／右声道接反low output输出弱dial pointer stop指针停pointer jump指针跳动poor sensitivity灵敏度差poor wow&flutter抖摆率差no tape protective无磁带保险eat tape吃带play distortion唱带失真playing delay放音延迟tape play fast放音快tape play slow放音慢vibration严重噪声tuning wobble, rubbing, noisy, slipping, malfunction 调谐不稳定，有磨擦，有噪音，滑动，功能失调display lens missing and/or windowsmisalignment缺显示镜或显示窗未对齐cabinet screw loose, stripped, missing ,rusted 外壳螺丝松动，螺丝齿有损，缺螺丝，螺丝gap between mating parts, balancing of twin cassette doors>0.8mm 配件间有缝隙，盒式磁带双门平衡差大于0.8mmflywheel mechanical noise,malfunction飞轮机械有噪音，有故障parts missing, loose parts/foreignbody inside缺部件，部件松，内有异物transformer mum/buzz noise变压器（火牛）有噪音CD/cassette door and/or flaps, hinges damaged inoperative, broken 唱碟／盒式磁带门盖，合页破损／不起作用mains cable damaged 2nd insulation layer and/or conductors exposed 电源线破损，第二绝缘层和／或导体／导线外露mains cable in wrong colorindication电源线颜色指示错sub-standard mains cable (failed torequired safety standard)电源线（次）不符合标准connecting wire pinched betweenmating part配件间接线受损discolor case外壳褪色molded marks, sink marks, flow lineon cabinet外壳有浇铸痕，缩痕，流水痕unit burnt smoke comes out产品冒烟operation malfunction, intermittentor shock noise with or without tapping the UN 功能故障／间歇故障（轻敲产品）时有噪声connecting jacks&plugs intermittentwhen moving the wire移动导线时插头和插口接触不良volume, equalizer&banlance control intermittent, noisy, faulty 音量／均衡器＆平衡控制功能有间歇／有噪音／出错stereo channels reversed立体声频道接反sound distortion ,hum, buzz, rattleor vibration声音失真，颤音，嗡鸣，咔哒声speaker damaged /faulty causedsound distortion, hum, buzz, rattle or vibration 扬声器有损／故障导致声音失真，颤音，嗡鸣，咔哒声speaker connection in wrong phase喇叭接线相位出错buzz noise from poor wiring, loose plastic parts, loose battery spring 接线不良，塑料配件松动，电池弹片松动导致嗡嗡声indicator light inoperative, dimmed,wrong color指示灯不起作用LED/LCD display with segment missing, excess, or uneven segment LED/LCD显示缺划，多划或划不均LCD display with obvious rainbowmarks LCD显示屏有明显的彩虹印earphone,headphone externalspeaker inoperative/intermittent耳机，头戴耳机无功能或间歇external aerials, DC adaptor or other accessories inoperative/intermittent 外接天线，直流转接器，或其它附件无功能或功能间歇damaged/cracked PCB印刷电路板损／坏poor wire dressing causing functionproblem电线外包皮不良导致功能问题poor solding, dry joint, componentsbridging焊接，干接，组件连接不良weak radio reception无线电台接收弱radio signal unstable无线电台信号不稳定frequency drift/off alignment频率飘移／不能对准tape record/playback distortion,weak磁带录音／重放失真，声弱tape chewed, jammed inside deckmechanism卡座内发生绞带／卡带carton materials too flimsy to besuitable for transportation纸箱材质太差不适合运输unit without polybag产品未套胶袋polyfoam endcap broken bur passeddrop test保丽龙端盖破但试摔通过AM调幅FM调频SM调波antenna天线sensor position遥控balance control左右平衡控制tone control音量控制treble control高音控制bass control低音控制stereo jack立体声控制dial lens刻度透镜dial pointer波段指示针dial pointer belt指示针带FM stereo indicator调频立体声指示灯speaker喇叭speaker box喇叭盒speaker grill喇叭网left channel左声道right channel右声道function selector功能选择纽tuning knob转动选台纽EQ knob均衡纽Hi-speed switch高速纽fast forward button快进纽record button录音纽play button放音纽pause button暂停纽stop/eject button停／出带纽search and skip backward button向后搜索及跳跃纽search and skip forward button向前搜索及跳跃纽volume knob音量纽volume down knob音量降低纽volume up button音量升高纽cassette knob卡座纽cassette卡座deck door AＡ门卡座deck door BＢ门卡座deck door lens卡座门镜battery spring电池弹簧backplate机背板connecting tab联结扣deck mechanism机芯handle提手head phone头戴耳机CD door唱碟门CD open/close button唱碟开／关纽CD play/pause button唱碟放音／暂停纽CD program button唱碟程序纽CD repeat button唱碟重复纽CD stop button唱碟停止纽turntable黑胶唱盘rotate switch旋转开关power switch电源开关flashlight - 手电筒light bulb dead灯泡不亮foreign metal particles inside unit手电筒内有金属粒子foreign plastic particles inside unit手电筒内有塑胶粒子Dehumidifier - 干燥器Rena ware compact air cleaner -空气过滤器loose switches/control panel(poor assembly)开关／控制面板松动（组装不良）gap between two halves of thehousing机架两半之间有缝隙function indicators damaged功能指示器损坏incorrect color of functionalindicator功能指示器颜色不正常unit rock or wobble when sitting ona level surface置于水平平面上晃动不稳power cord is united or irregularlytied电源线未接上或接的不规则missing rating plate/label缺等级牌／标签missing S/N label缺序列号missing filters缺过滤器missing safety marks (such as UL. EMC or CE)on product 缺产品安全标志（如：UL, EMC, CE)poor tampo-printing on controlpanel控制面板上字体印刷不良brand logo or key instructions offposition标识或功能键指示功能移位filter poorly sealed过滤器密封不良papers in H.E.P.A filter broken or poorly glued H.E.P.A过滤器内纸破裂或粘贴不良key jammed/stuck按键卡住plug pins rusted/oxidized插头生锈／已氧化something inside内有异物installation screws too loose安装螺丝太松keys too tight when pressing按键太紧incorrect brand name/model ofmotor马达品牌／型号不对rubber feet loosed out象胶支脚松掉incorrect style of supply cord电线型号不正确internal connection wires disheveled内部连限混乱smoking from the inside of theproduct产品内冒烟strain relief can not bear a force of15 LBS for 3 minutes张力不足以承受3分钟15磅overheating after running for hours数小时运行后机体过热no ionizer function无电离功能fan can not rotate风扇不转fan speed key malfunction风扇调速键故障difficult to assemble/reassemble装配／重装困难ionizer voltage measured does notmeet the minimum voltage电离电压不及最小电压值incorrect polarity极性错误abnormal noise异常噪声reliability test failed可靠性测试失败fan speed measured exceed thespecified range风扇速度测试超过规定速度air load exceed the specified range空气负载超过规定范围function indicators have no function功能指示器无功能fuse no function保险丝无功能master carton poorly tape-sealed卡通箱捆绑不良electric toothbrush - 电动牙刷dielectric strength test failed介电／绝缘强度测试失败overheating (enclosure melted)热度过高（外壳熔化）enclosure or parts broken or cracked外壳／附件破裂／破碎foreign particle inside the enclosure外壳内有异物significant noise噪音过大component loosen out duringoperation操作中部件松脱pushbutton switch or unit functionintermittent按钮开关或产品功能间歇button/switch stuck close按钮／开关卡住missing UL listing mark or European approval agency mark 缺UL标志或欧洲认可的代理机构的标志hard to assembly on brush head (tooloose)牙刷头难以安装poor assembly on brush head (tooloose)牙刷头装配不良poor alignment on brush head(uneven clearance)刷头上（刷毛）排列不匀brush head movement too fast or tooslow刷头转速过快／过慢wrong component is used用錯部件rust on battery contact insertliterature电池/充电器通电点生锈battery charger no function电池无功能hard to assembly or disassemble thebattery电池拆装困难omission of , insufficient , incorrect, separately packed component or accessories 单独包装的部件/附件缺,数量不足或装错enclosure not secured in place orwith excessive gaps外壳未固定到位,间隙过大color mismatch or inconsistence颜色配错/颜色不一致IRON - 电熨斗damaged power supply cord电源线受损live wire exposed火线外露short circuited (external fuses burntout)产品短路(外保险丝烧毁) failure of thermo cut off自动调温器不能断电switch intermittent开关间歇thermostat malfunction自动调温器故障current or voltage out ofspecification电流,电压超出规定foreign metal particles inside theunit(EG solder)产品内有金属颗粒component loosen out duringoperation操作过程中部件松脱foreign plastic particles inside theunit产品内有塑料颗粒intermittent间歇wrong component used部件用错TELEPHONE - 电话loose name plate, logobadges,function inlays etc.商标,标牌,功能指使松脱excessive gap betweencabinets(>0.8mm)外壳空隙过大knobs missing ,wrong type ,wrong color ,loosened off during operation 缺旋钮/旋钮型号不对/颜色不对/操作中松脱knobs wobble , rubbing , poor alignment, fitted in wrong way 旋钮摇晃不稳/有磨擦/排列不齐/排列方式不对display lens missing and/or windowsmisalignment缺失显示屏/显示屏窗口未对准cabinet screw stripped外壳螺钉缺螺纹connecting wire pinched betweenmating part配件间接线受挤压ringer Hi/Lo/Off no function响铃无 高／低／关 切换功能long distance ringer no function远距离响铃无功能ringer distortion响铃失真ringer weak响铃弱sound poor reception声音接收不良sound poor transmission声音传送不良no dial tone sound无拨号音pulse dialing no function脉冲拨号无功能redial no function重拨无功能handfree no function免提无功能memory no function记忆无功能flash no function闪断无功能mute no function弱音器无功能speaker phone no function扬声器电话无功能memory setting no function记忆设置无功能clock/timer set no function闹钟／计时器设置无功能handset test out of limit听筒测试超出限制hold no music保持（不挂机无音乐）operation malfunction, intermittentor shock noise with/without tapping the unit 功能／功能间歇（轻敲产品时有噪音connecting jacks&plugs intermittent when moving the wire 移动电线时接线端子和接线塞子接触不良speaker sound distortion , hum, buzz, rattle, or vibration 扬声器（话筒声音失真／有蜂鸣／咔嗒声／咯咯声／有颤音power consumption & operatingvoltage out of limit功率消耗／工作电压超限buzz noise from poor wiring, loose plastic parts , loose battery spring 接线不良／塑料零件松脱／电池弹片松脱 造成电话有蜂鸣indicator light inoperative, dimmed, wrong color 指示灯不亮／光线暗淡／颜色错误LED/LCD display with segment missing, excessive or uneven LED/LCD显示缺划／多划／划不均earphone , headphone, externalspeaker inopearative/function intermittent 耳机／头戴耳机扬声器无功能，功能间歇poor wire dressing causing functional problem 电线外包皮包裹不良导致功能问题poor soldering, dry joint ,components bridging焊接／干接／桥接不良sensitivity out of limit灵敏度超限keys/buttons stuck按键／按钮卡住polyfoam endcap broken but passdrop test泡沫塑料端盖破裂但通过试摔wall mounting hole墙安装孔storeage compartment储物箱desk lid平台盖hook挂钩memory记忆ornament ball装饰球ornament bell装饰铃microphone麦克风telephone line cord电话线line cord jack电话线插口handset听筒handset cord听筒线handset cord jack听筒线插口handset cradle听筒架receiver受话器tansmitter送话器memory记忆tone dialing音频拨号pulse dialing脉冲拨号dial board拨号盘dial mode knob拨号方式键ring control knob响铃控制键receiver volume knob受话音量控制钮dial buttons拨号钮flash knob flash键handfree knob免提键redial key重拨键reset key复位键hair dryer - 吹风机barrel桶clamp钳cool safety tip安全冷端grille网handle把heat section加热部位heatproof rim隔热圈hi/off/low switch高／关／低 开关lower cabinet下壳top cabinet上壳plug插头plug foot插脚power cord电源线air concentrator吹风头air intake grille进气网air supply opening进气口ALCI漏电保护制reset button复位键thermostat malfunction自动调温器故障foreign (metal/plastic) particlesinside unit (E.G. solder)内有金属／塑料异物（如焊料）component loosed out duringoperation使用中部件松落damaged power supply cord电源线坏live wire exposed and accessible火线外露可触short-circuited (external fuses burnout)短路（保险丝烧坏）switch intermittent开关间歇current or wattage out ofspecification电流或瓦特数不合要求General - 电子通用extra segment多划missing segment少划display abnormal显示不正常display flash数字闪display显示屏function key功能键lens透镜number key数字键Clock watch - 钟表accuracy test精确度测试alarm闹钟back casing表壳背面front casing表壳正面bell铃ringer表带belt buckle表带扣belt lining表带内衬canopy钟罩clock mechanism机芯dial刻度盘dial cover刻度盘盖frame钟框hour hand时针minute hand分针second hand秒针pendulum钟摆time adjustable knob时间调节钮alarm activate earlier闹钟提前alarm delay闹钟延迟clock hands misalignment指针误差hands collide指针碰撞inaccuracy精确度差pendulum swung slowly钟摆摆慢unadjustable不能调节knob missing按钮缺失knob loosened off during operation操作过程中，旋钮松落knob wobble /rubbing/ pooralignment /fitted wrong way旋钮摇晃／有磨擦／未成一直线／装错data cord数据线disk磁碟disk protective clip磁碟保护金属片left button左键right button右键middle button中键pc/ms button pc/ms 钮Calculator - 计算器Camera - 相机view finder取景器lens镜头lens definition镜头清晰度mechanical shutter快门film counter胶卷计数器flash lamp闪光灯winder mechanism卷带装置charging indicator充电指示灯rewinder倒带装置neck strap领带。

不良描述中英文对照Goods Supplement补货1.Plastic parts 塑胶部件Abrasion/划痕、Bubbles/气泡、Burrs/毛刺、Bad Plating/电镀不良、Contamination/杂质、Crack/爆裂、Combine Lines/结合线、Deformation/变形、Flow Marks/流痕、GreasyDirt/油污、Haze/雾状、Jelly/泠胶、Mold Marks/模痕、Melange Color/混色、Oppilation Hole/盲孔、Pull White/拉白、Pour Hole uneven/浇口不平、Wrong Stamping/字麦不符、Short Shots/缺料、Shrinkage/缩水、Stripped Screw/螺丝滑牙、Top White/顶白、Weld Lines/夹水纹、Wrong Dimension/尺寸不符、Wrong Texture/纹理错误、Light/发亮，Gaps裂缝、Steps 披峰、表面有手指印Surface finger prints、丝印错误Wrong printing、丝印偏移Printing slanted、丝印重影Printing double image、丝印有污点，拖尾Printing smearing、丝印不平坦（多油或少油）Printing uneven ( thin / thick )、丝印对于中心偏位Printing off centre、压痕或凹痕Press mark 或dented mark、反光或毛刺Flashing 或 burr、镜片有针孔Pin hole on lens.光泽luster/白点white dot、黑点black dot、装配不合格assembled NG、缺口Nick裂split2.Metal Parts 五金部件Abrasion/划痕、Bad Weld/焊接不良、Burrs/毛刺、Bad Plating/电镀不良、Bend angle/折弯角度、Contamination/杂质、Crack/爆裂、Deformation/变形、Dents/凹痕、Greasy Dirt/油污、Mold Marks/模痕、Missing Stamp/漏冲压、Oppilation Hole/盲孔、Pressing Marks/压痕、Rust/生锈、Wrong Stamping/字麦错误、Short Shots/缺料、Stripped Screw/螺丝滑牙、Pits/疤痕、Specks/斑点、Wrong Texture/纹理错误、Wrong Dimension/尺寸不符3.Painting partsSilkScreen parts 喷油/丝印部件Inspection Points /检查要点 :Bleeding/渗色 ,Bad Painting/喷油不良 ,Contamination/杂质 ,deviate position/偏位 ,Flow Marks/流痕 ,Missing paint/漏喷,Over Paint/肥油 ,Pits/疤痕 ,Poor Adhesion/附着力差 ,Print Words Leans/印刷字体倾斜 ,Pooring Paint/薄油,Silkscreen Haze/丝印模糊 ,Silkscreen Stamping Inconsistency/丝印字样不一致 , Scratch/划伤 ,Speck/斑点 ,Uneven Surface Oil/表面油层不均匀 ,Words Break Off/字体断开 ,Wrong Color/错误颜色 ,Wrong Texture/纹理错误 ;4.PCB 印制线路板Open/开路;Short/短路;Weave Texture/板料席纹;Foreign Residue/外来杂物;Delamination/爆板,分层;Dent/凹陷;Dent on G/F/金手指凹陷;Scratch/擦花;Misregistration/对位不正;Board Damage/板子损坏;C/M Illegible/白字不清;C/M on pad/白字上垫;Copper expoure/露铜;Solder Mask on Pad/绿油上垫;Uneven Solder Mask/绿油不平均;Solder Mask peeling off/绿油脱落;Missing Hole/漏孔;Excess Hole/多孔;Wrong Hole Size/孔径错误;Hole Breakout/崩孔;Nick Trace/线路缺口;Void on Trace/线路铜穿;Diskdown/线路不良/狗牙;Solder Mask inside hole/绿油入孔; Discolouration under Solder Mask/绿油颜色不良; Foreign matter under Solder Mask/绿油下杂物; Solder Mask skipping/不过油;Solder on Gold Finger/金手指上锡;Poor Bevelling/斜边不良;Gold Finger burrs/金手指损坏;Ping Ring/粉红圈5.Electronic parts 电子元件No AVL/没AVL;not on AVL/不在AVL上;Mfg/Mfg P/N dis-match AVL/ 与AVL不符;D/C overdue/ D/C 过期;无D/C;wrong part/错料;no reel/无卷轴;bulk packing for chip/ 散装;No dry packing(HIC change color)/ 无真空包装(防潮卡变色); No ESD packing/无防静电包装;illegible marking/印字不清,wrong marking/印字错;deformation/变型 ;micro crack/裂料;damaged part/ 烂料 ;Lead bent(PTH/SMT)/脚弯;Solder balls damaged/锡球坏wrong lead form/脚型错;wrong pitch/脚距不符;coplanar problem/平整度不良;pad(lead) oxidization/锡垫(引脚)氧化;wrong direction in tape(tray)/带中(盘中)方向错;short pins/引脚短;failed in solderability/ 焊锡不良;size(dimensions) out of specification/ 尺寸超标;function fail/ 功能不良;no tolerance/无误差范围;contamination/杂质;wrong identification for pin1/ 第1脚标识错.Broker Buy/炒料;(巻装物料)巻带前无空余巻带No blank cover tape for feeder loading 巻带粘力不足Not enough adhesive for the cover tape. 料盘变形Reel Deforming/卷带变型.。

不良现象中英文对照表1.缺件(missing parts)2.错件(wrong parts)3.多件(excessive parts)4.短路(short)5.断路(open)6.线短(wire short)7.线长(wire long)8.拐线(wire poor ddress)9.冷焊(cold solder)10.包焊(excess solder)11.空焊(missing solder)12.锡尖(solder icicle)13.锡渣(solder splash)14.锡裂(soder crack)15.锡洞(pin hole)16.锡球(solder ball)17.锡桥(solder bridge)18.滑牙(screw loose)19.氧化(rust)20.异物(foreigner material)21.溢胶(excessive glue)22.锡短路(solder bridge)23.锡不足(solder insufficient)24.极性反(wrong polarity)25.脚未入(pin unseated)26.脚未出(pin unvisible)27.脚未剪(pin no cut)28.脚未弯(pin not bent)29.缺盖章(missing stamp)30.缺标签(missing label)31.缺序号(missing s/n)32.序号错(wrong s/n)33.标签错(wrong label)34.标示错(wrong mark)35.脚太短(pin short)36.j1不洁(j1 dirty)37.锡凹陷(solder scooped)38.线序错(w/l of wire)39.未测试(no test) 40.vr变形(vr deformed)43.零件沾胶(glue on parts)41.pcb翘皮(pcb peeling)42.pcb弯曲(pcb twist)44.零件脚长(parts pin long)45.浮件(parts lift)46.零件歪斜(parts tilt)47.零件相触(parts touch)48.零件变形(parts deformed)49.零件损坏(parts damaged)50.零件脚脏(pin dirty)51.零件多装(parts excess)52.零件沾锡(solder on parts)53.零件偏移(parts shift)54.包装错误(wrong packing)55.印章错误(wrong stamps)56.尺寸错误(dimension wrong)57.二极管坏(diode ng)58.晶体管坏(transistor ng)59.振荡器坏(x’tl ng)60.管装错误(tubes wrong)61.阻值错误(impedance wrong)62.版本错误(rev wrong)63.电测不良(test failure)64.版本未标(non rev lebel)65.包装损坏(packing damaged)66.印章模糊(stamps defective)67.标签歪斜(label tilt)68.外箱损坏(carton damaged)69.点胶不良(poor glue)70.ic座氧化(socket rust)71.缺ul标签(missing ul label)72.线材不良(wire failure)73.零件脚损坏(pin damaged)74.金手指沾锡(solder on golden fingers)75.包装文件错(racking doc wrong)76.包装数量错(packing q’ty wrong)77.零件未定位(parts unseated)78.金手指沾胶(glue on golden fingers)79.垫片安装不良(washer unseated)80.线材安装不良(wire unseated)81.立碑(tombstone)。

1. Dim contrast/dimmer contrast：对比度暗2. ghost phenomenon：鬼影3. broken character：字符断裂4. Missing character：缺字符5. no display：不显6. dimmer segment：字节显示暗7. empty segment：缺段missing segment8. cable defect：导线不良9. connector defect：连接不良10. missing line：缺划11. heat seal defect：热压不良12. contamination：脏污13. abnormal display：显示异常，异显14. segment broken：字符断裂15. dent：压痕16. scratch：划伤17. LCD broken：LCD断裂18. wrong silk print：丝印错误19. dark display：显示暗20. abnormal backlight color：背光颜色异常21. dimmer backlight：背光暗22. stain：污点23. cable cut：电缆中断24. bezel stick out：铁框刺伤25. black dots：黑点26. half display：半显27. LCD bruise：玻璃撞伤28. bezel bend：铁框弯折29. LCD dead ：死屏30. flicker：闪烁31. reverse display：反显32. light spring：漏光33. broken wire：电线断裂34.TP：touch panel 触摸屏，触控面板35.AOI：automated optical inspection 自动光学检验Color sheet defect 荧光纸不良Light leakage 漏光Cable broken 断线Dimmer contrast 对比度暗Broken character 字符断裂Dent 压痕Missing character 缺字符No backlight 背光不亮Segment out 笔段不完全Empty segment 空白笔段Cable defect 导线异常Dark display 黑显Bezel stick out 铁框刺伤Bezel defect 铁框不良Repeat on/off display 重复出现开关显示Abnormal LED background color 异常的背光底色Cross talk 交叉No soldering on LED B/L connection cable and no attached protection tape 导线连接处无焊接和未贴黑色保护膜胶带No label 无标签No protection film 无保护膜Fell of the heat seal 热压脱落Wrong silk print 丝印错误No character 无字母Half display 半显Glass dent 玻璃凹痕LCD bruise 玻璃刺伤Bezel bend 铁框弯曲Connector defect 连接不良No soldering on LED B/L 背光无焊接Scratch on surface 表面划伤Broken TSP 触摸屏破损Defect packing 包装不良Muddy phenomena 模糊现象Material defect 材料不良Blinking 闪烁B/L defect 背光不良Horizontal missing line 水平缺划。

1板面凹痕dent2内层白斑I/L white spot3线路缺口circuit nick4蚀刻不净undering etching5绿油剥离S/M peel off6显影不净under developing7基材白点laminate measling 8铜面氧化copper oxi9绿油上焊盘s/m on pad10白字上焊盘c/m on pad11阻焊不良poor S/M12线路擦花 track scratch13锡上线sn on circuit14聚锡sn mass15锡灰sn gray16焊盘露铜copper exposed on pad 17锡上金手指sn on G/F18金手指凹痕G/F dent19金手指擦花G/F scratch20金手指粗糙G/F roughness21v-cut不良poor V-cut22倒边不良poor milling23针床压伤ET den24拖锡不良poor touch up25补金不良poor repairing Au26补油不良poor repairing s/m27针孔pinhole28胶渍paster stain29k孔内毛刺burrs in hole30锡珠入孔solder in hole31露铜expose Cu 40翘板warp41漏印字符skip42金粗Au too big43金簿Au too thin44金手指缺口G/F voids/nick on G/F 45金手指发黑G/F too black46字符印反inverse C/M47金手指针孔G/F pinholes48标志不清symbol unclear49标志错symbol wrong50绿油鬼影ghost in S/M51手指印finger print52补线不良poor line repairing53锡高exessive solde54孔小hole undersize55字符错wrong C/M56字符印偏C/M misalignment57字符入孔C/M in hole58字符重影C/M doubloe image59漏镀金手指missing plating G/F 60金手指发白G/F gray61焊盘脱落pad break off/pad peel off 62焊盘露铜pad expose cu63断绿油桥missing S/M bridge64塞孔block hole65水迹water print66锡珠solder ball67砂孔pitting68油薄69聚油excess solder mask70锡粗Sn too thick32露镍expose Ni33绿油起泡solder mask blister 34绿油起皱solder mask winbles 35金手指氧化G/F oxiding36金颜色不良Au discoloration 37金面凸起Au surface blister 38绿油入孔solder mask in hole 39爆板board angle damafe 71线路上锡Sn overlap scratch72绿油下杂物contamination under S/M 73焊盘损坏land damage74焊盘翘起lifted land75偏位misregistration76漏钻孔missing hole77焊盘缺口nick on pad78线路缺口nick on trac1开路open circuit2短路short circuit3线路缺口circuit nick4线路凹痕circuit dent5渗镀plating Bloody6焊盘缺口pad nick7内层白斑I/L white spot8黑化不良poor B.O9白斑measling10粉红圈pinking ring11层压起泡press blister12错位misregistation13偏位shift14孔内无铜no Cu on PTH15孔内毛刺hole burrs16 NPTH有铜Cu on NPTH17铜面露基材exposed laminate 18铜面凹痕dent on Cu surface 19胶渍gum residue20夹膜D/F nip21蚀刻不尽under etching22线幼line too thin23孔大hole oversize24孔小hole undersize25偏孔hole misregistration26铜面瘤粒Cu nodule27显影不尽under developing28铜面刮伤scratch on Cu surface 29塞孔hole plugged30修理不良poor repairing 31铜薄copper too thin32内层擦花I/L scratch33内层偏位I/L misregistation34内层杂物I/L inclusions35掉膜film off36干膜碎D/F meaking37退锡不尽poor Sn stripping38间隙小space too marrow39板薄board too thin40板厚board too thickness41针孔pinhole42崩孔breakout43侧蚀undercut44镀层粗糙plating layer roughness45亚色dull colour46焊盘翘起lifted land47漏钻孔missing hole 线路狗牙circuit wist 48露布纹weave exposure49钻偏孔hole misregistratiion50孔损害hole damage51基材分层delamination52蚀刻过度over etching53多孔hole too much54残铜remain Cu55孔内露基材laminate exposure in hole 56焊盘脱落pad break off57焊盘凹痕pad dent58焊盘凸起pad bulge59焊盘损坏pad damaged60焊盘缺口pad nick61焊盘露铜pad expos。

电脑故障描述中英文对照表MONITOR: 显示部分：there was single bright spot in the screen 屏幕上有亮点there was horizontal line in the screen 屏幕上有水平线there was vertical line the screen 屏幕上有垂直线poor focus 聚焦不准too bright to control 屏幕过亮不可调节too dim to control 屏幕过暗补可调节panel controls can't adjust 控制面板无法调节display shrink vertical 画面垂直收缩display shrink overall 画面全屏收缩display shrink horizontal 画面水平收缩display wobbling 屏幕晃动monitor magnetized 显示器磁化flickering display 屏幕闪烁trapezium distortion 梯形失真pillow model distortion 枕型失真single strong color 屏幕偏色broken video connector'pin 显示接口损坏broken cover/crust 外壳损坏scratched crt/lcd 屏幕划伤monitor no display and led no light 无显示，并且电源灯不亮distorted display 图像扭曲physics damage 物理损伤no video 屏幕无图像system board (MB) 主板故障类no post 开机无反应通常指能够加电但不能正常自检system no boot 系统不能引导monitor no display and led no light 无显示，并且电源灯不亮no power 开机不加电memory display error 内存报错hard disk display error 硬盘报错system often hang 系统经常死机serial port no answer 串口无响应parallel port no answer 并口无响应pcmcia port no answer pcmcia卡无响应lan port(RJ45）no answer 网口无响应modem port(RJ11) no answer modem口无响应FDD port no answer 软驱接口无响应keyboard port no answer 键盘接口无响应mouse port no answer 鼠标接口无响应usb port no answer USB接口无响应firewire(IEEE1394) port no answer 火线接口无响应there was wrong beeps from the MB 主板发出报警声BIOS battery can't charge BIOS电池掉电system auto shut down 系统自动关机infra-red port no answer 红外线口无响应physics damage 物理损伤speaker 音箱类speaker no output 音箱无声音输出there was cracking sound in the speaker 音箱有爆裂声speaker sound distortion 音箱声音失真cacophony 杂音keyboard 键盘类keys display garbage characters 显示字符与敲击字符不符keyboard connector pins damage 键盘接口损坏sticky keys 按键不能复位（粘键）inoperative keys 敲键不起作用keyboard error 键盘报错memory 内存类memory address error 内存地址错误no display and there was wrong beeps 无显示，并且有报警声run diagnostic test display error 运行诊断程序报错memory read/write error 内存读写错误memory can't recognise 不识别内存system often hang 系统经常死机nic 网卡类/modemnetwork can't connect 不能连接网络nic can't recognise 不识别网卡modem no dail tone modem无拨号音power supply 电源类no output 无输出power supply fan noisy 电源风扇噪音fan can't run 风扇不转low voltage of output 输出电压低battery 电池类battery can't charged 电池不能充电short battery life 电池寿命短driver(cd/dvd/combo-rom hdd fdd) 驱动器类can't recognize cd 不能识别光盘read error 读盘错误cd/dvd-rom read cd have noisy 光驱读盘噪音host can't recognize driver 主机不识别驱动器read/write/format error 读写格式化错误（hdd or fdd) there was bad sectors in the hd 硬盘有坏扇区hdd can't boot 硬盘不能引导can't eject disk 不能弹出盘片can't insert disk 不能插入盘片S.M.A.R.T error 硬盘自检程序报错other 其它latch of lcd broken lcd挂钩坏finger can't move when feel the touchpad 触摸扳不能移动bottom cover damage 底壳损坏top Case damge 上壳损坏system fan noisy 系统风扇噪音system can't recognizde xxxx 系统无法识别（某个设备）run software system hang 运行某个应用程序死机customer require recover system 客户要求恢复系统retrieval data 拯救数据附件二标准缩写标准描述缩写标准描述缩写ADAPTER ADPT MODEM MDM ADDRESS ADD MONITOR MON ADJUST ADJ MORNING AM ADVICE ADV MOTHER BOA RB MB ADVISE ADV MOUSE MS AFTER AFT NO FAULT FOUND NFFAFTERNOON PM NO TROUBLEFOUND NTFAIRWA Y BILL AWB NO PART USE NPU AND & NOTEBOOK NB ARRIVE ARR NUMBER NO. AS SOON AS POSSIBLE ASAP PART NO P/N AVAILA BLE AVAIL PLEASE PLS BATTARY BTRY POW ER SUPPLY PSU CABLE CBL PROBLEM PROB CANCEL CANX QUA NTITY QTY CLOSE CLZ QUOTATION/QUOTE QUO COMPLETE COMPL RECEIVE RCV CONFIRM CONF REINSTALL REIN CONNECTION CONN REPLA CE REPL CONTA CT CONT REPORT RPT COVER CVR REQUEST REQ CUSTOMER CUS RESPONSE RESP DEFECT DEFT RETURN RTN DEPA RTMENT DEPT REVISE REV DESKTOP DT REVISION REV DISPLA Y DISP ROOM RM EVENING EVE SCHEDULE SCHED FAILURE FAIL SCREW SCR FLOPPY DRIVE FD SERVER SVR FOLLOW UP F/U SERVICE SVC FOR 4 SOFTWARE SW FROM FR SOMETHING STH. HARDDISK HD SPEAKER SPKR HARDWARE HW SYSTEM SYS HOTEL HTL TELEPHONE TEL HOUR HR TOTA L TTL INFORM INF TRANSFER TRSF INFORMATION INFO WILL WL INVENTORY INV WITH W/ KEY BOA RD KB WITHOUT W/OLEA VE LV MAXIMUM MAX MESSA GE MSG MINIMUM MIN MINUTES MIN。

1>Abrasion: A surface imperfection that removes ordisplaces material characterized by itslarge width and length relative to itsdepth.中译: 擦破/磨损一个表面的瑕疵。

移动材料时造成较大的宽度、长度、深度之特征。

2>Bleeding: This defect is the discoloration createdby the diffusion of coloring materialthrough an applied coating from thesubstrate to the surface of the coating.中译: 渗出染料扩散，自底层到表层，造成表面上的瑕疵。

3＞Blemish: The change in the surface appearancedue to a flaw or cosmetic defect.中译: 污损/污点因为一个瑕疵或外观不良而改变表面外部4＞Blister: The raised bumps in the surface, causedby air or solvent vapors forming withinor under the coating.中译: 水泡由于来自烤漆内部或表面的空气或溶剂气体造成表面隆起突出。

5＞Blush: Discoloration or change in gloss, generallyappearing at the gates, abrupt thicknesschanges or other structures along flow pat.中译: 异色通常发生在射出进料口、肉厚突然缩减、或流道交错之处6＞Bubble: A gas pocket in a plastic molded part.For a coating, it is the same as blister.中译: 气泡一个气体包覆(中空)在塑料件上，对烤漆来说，与blister意义相同7＞Burn Mark: A condition where supper-heatedtrapped air in the cavity heats or burnsthe surface of the plastic part.中译: 焦痕8＞Burr:This defect appears as a rough or sharpedge on metal after it has been cast, cut,drilled, stamped, and so forth. Burrs willusually snag or tear a cleaning cloth.中译: 毛边(头) 在材料经过铸造、切割、钻孔、冲压等等外观形成一个粗糙或锐利边缘，毛边总是会刺穿或扯裂整齐的衣物。

PCB及PCBA缺陷中英文对照表PCB及PCBA缺陷中英文对照表1板面凹痕dent 41漏印字符skip2内层白斑I/L white spot 42金粗Au too big3线路缺口circuit nick 43金簿Au too thin4蚀刻不净undering etching 44金手指缺口G/F voids/nick on G/F 5绿油剥离S/M peel off 45金手指发黑G/F too black6显影不净under developing 46字符印反inverse C/M7基材白点laminate measling 47金手指针孔G/F pinholes8铜面氧化copper oxide 48标志不清symbol unclear9绿油上焊盘s/m on pad 49标志错symbol wrong10白字上焊盘c/m on pad 50绿油鬼影ghost in S/M11阻焊不良poor S/M 51手指印finger print12线路擦花track scratch 52补线不良poor line repairing13锡上线sn on circuit 53锡高exessive solder14聚锡sn mass 54孔小hole undersize15锡灰sn gray 55字符错wrong C/M16焊盘露铜cu exposed on pad 56字符印偏C/M misalignment17锡上金手指sn on G/F 57字符入孔C/M in hole18金手指凹痕G/F dent 58字符重影C/M doubloe image19金手指擦花G/F scratch 59漏镀金手指missing plating G/F20金手指粗糙G/F roughness 60金手指发白G/F gray21v-cut不良poor V-cut 61焊盘脱落pad break off/pad peel off 22倒边不良poor milling 62焊盘露铜pad expose cu23针床压伤ET dent 63断绿油桥missing S/M bridge24拖锡不良poor touch up 64塞孔block hole25补金不良poor repairing Au 65水迹water print26补油不良poor repairing s/m 66锡珠solder ball27针孔pinhole 67砂孔pitting28胶渍paster stain 68油薄S/M too thin29k孔内毛刺burrs in hole 69聚油excess solder mask 30锡珠入孔solder in hole 70锡粗Sn too thick31露铜expose Cu 71线路上锡Sn overlap scratch 32露镍expose Ni 72绿油下杂物contamination under S/M 33绿油起泡solder mask blister 73焊盘损坏land damage34绿油起皱solder mask winbles 74焊盘翘起lifted land35金手指氧化G/F oxiding 75偏位misregistration36金颜色不良Au discoloration 76漏钻孔missing hole37金面凸起Au surface blister 77焊盘缺口nick on pad 38绿油入孔solder mask in hole 78线路缺口nick on track 39爆板board angle damafe40翘板warp1开路open circuit 46焊盘翘起lifted land2短路short circuit 47漏钻孔missing hole线路狗牙circuit wist 48露布纹weave exposure3线路缺口circuit nick 49钻偏孔hole misregistratiion 4线路凹痕circuit dent 50孔损害hole damage5渗镀plating Bloody 51基材分层delamination6焊盘缺口pad nick 52蚀刻过度over etching7内层白斑I/L white spot 53多孔hole too much8黑化不良poor B.O 54残铜remain Cu9爆板measling 55孔内露基材laminate exposure in hole10粉红圈pinking ring 56焊盘脱落pad break off 11层压起泡press blister 57焊盘凹痕pad dent12错位misregistation 58焊盘凸起pad bulge13偏位shift 59焊盘损坏pad damaged14孔内无铜no Cu on Pth 60焊盘缺口pad nick15孔内毛刺hole burrs 61焊盘露铜pad expose Cu 16NPTH有铜Cu on NPTH 30修理不良poor repairing17铜面露基材exposed laminate 31铜薄copper too thin18铜面凹痕dent on Cu surface 32内层擦花I/L scratch19胶渍gum residue 33内层偏位I/L misregistation20夹膜D/F nip 34内层杂物I/L inclusions21蚀刻不尽under etching 35掉膜film off22线幼line too thin 36干膜碎D/F meaking23孔大hole oversize 37退锡不尽poor Sn stripping 24孔小hole undersize 38间隙小space too marrow 25偏孔hole misregistration 39板薄board too thin26铜面瘤粒Cu nodule 40板厚board too thickness27显影不尽under developing 41针孔pinhole28铜面刮伤scratch on Cu surface 42崩孔breakout29塞孔hole plugged 43侧蚀undrcut45亚色dull colour 44镀层粗糙plating layer roughness PCB及PCBA常用度量衡单位换算所属目录：FASTPCBA靖邦公司资料发布时间：2009-01-01 1英尺=12英寸1英寸inch=1000密尔mil1mil=25.4um1mil=1000uin mil密耳有时也成英丝1um=40uin（有些公司称微英寸为麦，其实是微英寸）1OZ=28.35克/平方英尺=35微米H=18微米4mil/4mil=0.1mm/0.1mm线宽线距1ASD=1安培/平方分米=10.76安培/平方英尺1AM=1安培分钟=60库仑主要用于贵金属电镀如镀金1平方分米=10.76平方英尺1盎司=28.35克,此为英制单位1加仑(英制)=4.5升1加仑美制=3.785升1KHA=1000安小时1安培小时=3600库仑比重波美度=145-145/比重SG.SG.比重（克/立方厘米）=145/（145-波美PCB及PCBA行业专用名词PCB及PCBA行业专用名词BOM(Bill of material) 物料需求單Laminate 基板Copper foil 銅箔Solder mask(s/m) 防焊Bare Board 空板Microetching 微蝕Exposure 曝光Dry Film 干膜Matte side 毛面Rcc(Resin coated copper) 背膠銅箔Final shaping 成型Electrical test(ET) 電測Visual Inspection 外觀檢查Gold Finger(G/F) 金手指Legend 文字Post Cure 后烤Desmear 除膠渣Developing 顯影Pattern Plating 線路電鍍Panel Plating 全板電鍍Puddle Effect 水坑效應Oxide Coating 黑氧化Routing Bit 銑刀Tolerance 公差Post Treatment 后處理Adhesion 附著力Stripping 去膜Baking 烘烤AQL(acceptable quality level) 品質允收水準Optical Target 光學靶點Lay up 疊合Chromation 鉻化處理Undercut 側蝕Microvia 微孔Annular Ring 孔環Burr 毛頭Entek 有機保焊處理Conformal Mask 銅窗Drum Side 光面Diazo Film 偶氮棕片Cut Lamination 下料Sheets Cutting 裁板Inner Layer Drilling 內層鑽孔Outter Layer Drilling 一次孔2nd Drilling 二次孔PCB及PCBA专用名词Laser Drilling 雷射鉆孔Blind&Burried Hole Drilling 盲(埋)孔鉆孔screen printing 網版印刷silk screen 絲網印刷scum 透明殘膜skip printing 跳印漏印squeege 刮刀type 种類abietic acid 松脂酸air knife 風刀bridging 搭橋橋接flux 助焊劑product process 制程pre-process 制前solder bridge 錫橋soler bump 錫突solder plug 錫塞immersion gold 浸金(化金)thin core 薄基板twist 板翘, 板扭warp ,warpage 板彎weave eposure 織紋顯露wicking 燈蕊效應yield 良品abrasion resistance 耐磨性absorption 吸收accelerated test 加速實驗acceleration 速化反應accelerator 加速剂batch 批cold solder joint 冷焊點component side 零件面double side 雙面double side board 雙面板fiducial mark 基準記號finished board 成品板lot size 批量rack 掛架register mark 對準用標記solder side 錫鉛面thickness 厚度warehouse 仓库wet process 濕制程Beveling 斜邊chamfer 道角dimension 尺寸Fixture 治具interconnection 互相連通line space 線距line width 線寬misregistration 對不准mouse bite 蝕刻缺口nick 缺口master drawing 主圖print and etch board 印刷後及蝕刻後板crease 皺褶dent 凹陷glass fiber 玻璃纖維布pin hole 針孔pit 凹點target hole 靶孔PCBA及PCB专用名词(二)PCBA及PCB专用名词(二)Black Oxide Removal 黑化還原Plug Hole 塞孔Ink Print&precure 印刷及預烤Scrub 表面處理Spray Coating 靜電噴涂Printing of Legend 文字印刷Pumice ( Wet Blasting) 噴砂Immersion Ni/Au(Electoless Ni/Au) 浸鎳金Hot Air Solder Leveling 噴錫N/C routing 撈型Beveling of G/F 金手指斜边Cleanning&Baking 清洗及烘烤Fixture Testing 治具測試original A/W 客戶原稿working A/W 工作片working master 工作母片carlson pin 定位梢component hole(>30mil) 零件孔drill facet 鑽尖切削面drill pointer 鑽尖重磨機drilled blank board 已鑽孔的裸板hole diameter 孔徑hole location 孔位hole number 孔數lay back 刃角磨損margin 鑽頭刃帶open circuits 斷路runout 偏轉slot 開槽spindle 鑽軸tooling hole 工具孔stacking structure 疊板結構blow hole, void in PTH hole 吹孔孔破deburring 去毛頭electroless-deposition 無電鍍化etchback 回蝕air inclusion 氣泡chase 網框fabric 網布liquid 液態\狀mealing 泡點trim line 裁切線v-cut v型切槽golden board 標準板back lighting 背光crack 裂痕crazing 白斑dimension stability 尺寸安全性failure 故障fault 缺陷瑕疵gap 鑽尖分開gel time 膠化時間haloing 白邊白圈hardener 硬化劑hole counter 數孔機hook 外弧insulation resistance 絕緣阻抗ionizable(ionic) contaminants 離子性污染land 焊墊microsectioning 微切片法negative etchback 反回蝕overlap 鑽尖重曡peel strength 抗撕強度pink ring 粉紅圈REJ(reject) 拒收退貨release agent(sheets) 脫膜劑resin content 膠含量resin flow 膠流量resin recession 樹脂下限resin smear 膠渣rework 重工specification(spec.) 規範innerlayer&outlayer 內外層gold plating 鍍金QC(quality control) 品管back up 墊板blister 起泡局部分层caul plate 隔板, 钢板open circuits 断路sampling size 抽樣數edge spacing 板邊空地ground plane 接地層laminator 壓膜機M/T 磁帶disk 磁片。