STYX HELIX

Vehicle Ident. No.______________________Working instructionfor order no.Maintenance(Labour operation 03 16 00 ..)For a description of the various models, see Technical Manual Mix fuel in fuel tank with additive (Keropur from Porsche; Part No. 000 043 206 89) *** For country allocation, see Overview of C markets** Applies only for ChinaContinued overleafCopyright byDr. Ing. h.c. F. Porsche AGAfter Sales Engineering - 11/12Tyres and spare wheel: Check conditionElectricsWindscreen wiper/washer system, headlight washer: Check function and nozzle settingsNote:If the mileage for a regular service is not reached, maintenance must be carried out after 4, 8, 12...... years.Particle filter: Replace filter elementThe term 'checking' includes all necessary subsequent work such as adjusting, readjusting, correcting and topping up, but does not include repairing, replacing and reconditioning parts or assemblies.Diagnostic system: Read out fault memory and transfer gear wear integrator; reset maintenance interval;Read out soot mass particle filter (Cayenne Diesel / S Diesel only)Check wiper bladesOutside the vehicleInside the vehicleat 60,000, 120,000, 180,000, 240,000 km/36,000, 72,000, 108,000, 144,000 mls etc.Maintenance (C markets*)Cayenne (V6) / S / GTS / Turbo / Diesel / S Diesel / S HybridAs of model year 20129Tyres and spare wheel: Check tyre pressureCheck drive belt (only if vehicle is used for off-road driving)Visual inspection for leaks (oils and other fluids)Coolant: Check level and antifreezeSeat belts: Check function and conditionFill in engine oil (observe oil change service plan for all Cayenne models)Horn: Check functionAll headlights: Check adjustmentTrailer hitch: Check functionLubricate door arrester and fastening boltsBrake hoses: Visual inspection for damageBrake lines: Visual inspection for damage, correct routing and corrosionBrake system: Visual inspection of brake pads and brake discs for wearDrain engine oil, change oil filter (observe oil change service plan for all Cayenne models)Underbody panels: Visual inspection for completeness, secure installation and damageVisual inspection for leaks (oils and other fluids)Under the vehicleRadiators and air intakes: Visual inspection for external soiling and blockageExhaust system: Visual inspection for leaks and damage, check engine mountsEngine compartmentAxle joints: Check the play and visually inspect the dust bellows for damageThrottle housing: clean inside **Fuel lines and connections: Visual inspectionSteering gear: Visual inspection of the bellows for damageWindscreen wiper/washer system: Check fluid level; check window cleaner and antifreeze, depending on the season, use Porsche approved windscreen cleaner onlyPDCC and power steering: Check fluid levelTie rod joints: Check the play and dust bellowsDrive shafts: Visual inspection of the boots for leaks and damageReplace fuel filter (Cayenne Diesel / S Diesel only)Cardan shaft: Visual inspection of the rubber bellows for damageVehicle Ident. No.______________________Working instructionfor order no.9Replace spark plugs - Cayenne 3.0 V6 / S Hybridevery 20,000 km/12,000 mls or every 4 years Replace spark plugs - Cayenne (V6)every 60,000 km/36,000 mls or every 4 years Replace spark plugs - Cayenne S / GTS every 30,000 km/18,000 mls or every 4 years Replace spark plugs - Cayenne Turbo every 20,000 km/12,000 mls or every 4 years (Labour operation 03 83 00 ..)(Labour operation 03 85 00 ..) (Labour operation 03 95 00 ..) (Labour operation 03 51 00 ..) (Labour operation 03 52 00 ..)Signature (mechanic): ____________________________Test drive:Signature (final check): _________________________Copyright byDr. Ing. h.c. F. Porsche AGAfter Sales Engineering - 11/12Porsche Centre Replace PDCC reservoirMaintenance (C markets*)Cayenne (V6) / S / GTS / Turbo / Diesel / S Diesel / S HybridAdditional maintenance, replacing spark plugsOils, fluids: Visual inspection for leaks(Labour operation 03 81 00 ..)Complete Condition Report for Long-Life GuaranteeRemote control, front seats, electric parking and foot brakes (also actuation travel), engine, clutch, steering, transmission, ParkAssist, cruise control, PSM switch, heating, sports exhaust system, air conditioning and instruments: Check function Every 2 yearsManual transmission: Change oilAir cleaner: Replace air-cleaner element (Cayenne (V6), S, GTS, Turbo, S Hybrid)Air cleaner: Replace air-cleaner element (Cayenne Diesel / S Diesel)Transfer gear (Cayenne Diesel, S Hybrid, V6): Change oilAdditional maintenance every 90,000 km/54,000 mls or every 6 yearsAs of model year 2012Turbo compressor: Replace drive belt (Cayenne 3.0 V6, S Hybrid)Rear final drive: Change oilAll-wheel final drive: Change oilAdditional maintenance every 120,000 km/72,000 mls or every 4 yearsAdditional maintenance every 240,000 km/144,000 mls or every 16 yearsClutch: Change brake fluid; perform test and adaptation (Cayenne S Hybrid only)Every 4 yearsReplace tyre sealantChange brake fluid (use only original Porsche brake fluid)Tiptronic transmission: Change ATF and ATF filter。

Symbol Test Conditions Maximum Ratings V DSS T J = 25︒C to 150︒C250 V V DGR T J = 25︒C to 150︒C, R GS = 1M Ω 250 VV GSS Continuous ±20 VV GSM Transient±30 VI D25T C = 25︒C 110A I DM T C = 25︒C, Pulse Width Limited by T JM 300A I A T C = 25︒C 25A E AS T C = 25︒C1J P D T C = 25︒C 694Wdv/dt I S ≤ I DM , V DD ≤ V DSS , T J ≤ 150°C 10 V/nsT J -55 to +150 ︒C T JM +150 ︒CT stg -55 to +150︒CT LMaximum Lead Temperature for Soldering 300°C T SOLD 1.6 mm (0.062in.) from Case for 10s 260°C M d Mounting Torque (TO-247) 1.13/10 Nm/lb.inF CMounting force (PLUS220SMD) 11..65/2.5..14.6N/lbWeight TO-247 6 g PLUS220SMD 4 gTrench TMPower MOSFETIXTH110N25T IXTV110N25TS V DSS = 250V I D25= 110A R DS(on)≤ 26m ΩN-Channel Enhancement Mode Avalanche RatedFast Intrinsic RectifierFeatures●International Standard Packages ●Avalanche Rated ●High Current Handling Capability ●Fast Intrinsic Rectifier ●Low R DS(on)Advantages●Easy to Mount ●Space Savings●High Power DensityApplications●DC-DC Converters ●Battery Chargers●Switch-Mode and Resonant-Mode Power Supplies ●DC Choppers ●AC Motor Drives●Uninterruptible Power SuppliesSymbol Test Conditions Characteristic Values (T J = 25︒C, Unless Otherwise Specified) Min. Typ. Max.BV DSS V GS = 0V, I D = 250μA 250V V GS(th)V DS = V GS , I D = 1mA3.05.0V I GSS V GS = ±20V, V DS = 0V ±200nAI DSS V DS = V DSS , V GS = 0V5 μA T J = 125︒C 250 μA R DS(on)V GS = 10V, I D = 0.5 • I D25, Notes 1, 226 m ΩG = Gate D = Drain S = Source Tab = DrainTO-247 (IXTH)GSDPLUS220SMD(IXTV_S)D D (Tab)GSIXYS Reserves the Right to Change Limits, Test Conditions, and Dimensions.Notes:1. Pulse test, t ≤ 300μs, duty cycle, d ≤ 2%.2. On through-hole package, R DS(ON) kelvin test contact location must be 5mm or less from the package body.Source-Drain DiodeSymbol Test Conditions Characteristic Values Terminals:1 - Gate 2,4 - Drain3 - SourceIXYS Reserves the Right to Change Limits, Test Conditions, and Dimensions.。

Pentra DX NexusProcess efficiency in HematologyComfort•Large color touch scr een.•Intuitive interface with virtualkeyboard.Ergonomics•Smart access to all functionalities.•Enhanced visibility.•Compr ehensiveicons.External links•USB port for multi-data exchange and hardwareconnection.•120 samples per hour •28 parameters•Automatic r eflex testing •Automatic validation of results •Integrated cytology atlas •SPS evolutionPentra DX NexusBe productive and flexibleQuality•Complete traceability for each run including identification, lot number and expiration date on r eagents andcontrols.Compatibility•Compatible racks with most pr e-analytical systems and post analytical systems.•Two models ofracks.Environment•New laser source r equi re less space, r educing heat and noise.(1) Laser LED (2) Photomultiplier (3) Hyd r ofocalisation (4) Impedancemetry (5) Optical mesur ementHematopoiesisthroughPentra DX RangeSCIENTIFIC BOOKReference methods CBC DIFF RET NRBC Impedancemetry ••••Flow cytometry •••••y r t e m o r o u l F Cytochemistry ••••SS H D (1)(2)(3)(4)(5)LMNE matrixDHSS ConceptFull leukopoiesis analysis:Flow cytometry Injection of the sample prepared in a double hydrodynamic flowcytometer (HORIBA Medical patent),and determination of the cell complexity by measuring the absorbance of a polychromaticlight source, or the fluorescence by fluorocytometry (Diode type laser at 488 nm wavelength).CytochemistryIncubation of the sample at a regulated temperature andcells stained with Chlorazol Black.This reagent stains specifically leukocyte cytoplasm, granules,and nuclei.• Matu re populations 5 DIFF • Reduced slide r eview• Diagnostic and follow-up tool for rapid decision-makingErythroblastsFluorescence-based count:•Eryth r oblast analysis in r outine or r eflex mode based on:- inte r nal laboratory rules - detection alarms- patient demographics...•Use of Thiazole Orange fluo rochrome•Double Hyd r odynamic Sequential System (HORIBA Medical Patent)ReticulocytesDifferential diagnosis of anemia:• Classification and monitoring of anemia based on the Reticulocyte count and the CRC (Corrected Reticulocyte Count)• Follow-up of i r on-deficiency anemia based on the MR V (Mean Reticulocyte Volume)• Detection and monitoring of the eryth r opoietic r esponse accor ding to three stages of maturation: RET High, RET Medium, RET Low and maturation parameters (IR F , MFI, and MR V)Erythroblasts ReticulocytesRed blood cellsSPS EvolutionPerfect standardization of blood smears•Integrated slide-maker*120 slides per hourFully automated and secured process•Choice of staining protocolsMay-Grünwald Giemsa, W right, W right Giemsa,etc.•Sampling volume: 50 µl of whole blood (additional) On primary closed tube •Positive identificationBarcode r eadingPatient data printed automatically on slide •Smearing flexibilityUser-defined smearing pr ofiles based on the laboratory’s own rules*Optional moduleExpert validation station Results validation•Full management of samplesAlarms trigger ed accor ding to patient pr ofile Delta checkPr ogrammable r erun and r eflex test rules •Automatic validationStandardization of Lab rules (integrated catalog) Inte r national r ecommendation rules for Hematology r eview (ISLH,Laboratory Hematology11:83-90 © 2005 Car den Jennings Publishing Co.,Ltd.doi:10.1532/LH96.05019) integrate d in r outineAutomatic validation based on rules,flags,patient history,etc.•Integrated cytology atlas: HematovisionAid to accurate diagnosis supportExcellent education tool •Quality assuranceContr ol blood managementGraphical and table statisticsXB managementQCP Export (Quality Cont rol Program)Complete traceability (r eagents & cont rols) for eachrunPentra DX NexusT echnical SpecificationsPHYSICAL SPECIFICATIONSDimensions & WeightHeigh t W idth Depth W eightW ithout SPS73 cm120 cm55 cm110 kg28.7in47.2in21.6in242.5lbW ith SPS73 cm170 cm55 cm170 kg28.7in66.9in21.6in374 lb PrinterLaserThroughputUp to 120 samples/hour in CBC, DIFF,CBR, SPS modesUp to 60 samples/hour in DIR,ERB, CBE modesOperating temperature16- 34°C (61-93°F) room temperatureSpecimen volumeManual cycle 130 µLAutomatic cycle 200 µLPower requirementsPower supply from 100 V AC to 240 V AC (± 10%)50 Hz to 60HzPower consumption Pentra DX120 900 V AReagentsABX DiluentABX L ysebio(cyanide free)ABX FluocyteABX Leucodi ffABX BasolyseABX CleanerPARAMETERSCBCWBC RBC HGB HCT MCV MCH MCHC RDW PLT MPVDifferential LeukocytesNEU# & NEU% L YM# & L YM%MON# & MON% EOS# & EOS% BAS# & BAS% ReticulocytesRET%RET#RETH%RETM%RETL%IMM%CRC%IRF%MRV ErythroblastsERB%ERB#SOFTWARE SPECIFICATIONSData ProcessingColor LCD:12.1inCapacity:90,000 resultsOperating System: W indows XP Embedded™Pr ocessor:Genuine Intel1.60GHzRAM(Random Access Memory): 1 GBExter nal DVD/CD drive connected to instrument USB portRS232C, 5 X USB1User definedflagging limitsT ransmit patient & QC to LISMono & bi-di r ectional connectionsQuality Control Management48 selectable QC filesXB: 100 operator selectablefiles with statistics (20 samples per file) W ith-in runLevey-Jennings graphsLogsReagents,quality cont r ol,calibration,maintenance, user, settings,communication, err ors,blanksPERFORMANCE DATALinearityParameters Standa rd UnitWBC0.1- 15010/mmRBC0.01 - 810/mmHGB0.65 - 24 g/dLHCT 1 - 67%PLT 6 - 190010/mmPLT (platelet concentrated) 6 - 280010/mm Precision:Parameters Rang e Unit s% CV WBC 4.0-10.010/mm< 2 RBC 3.6-6.210/mm< 2 HGB12.0-18.0g/dL< 1 HCT36- 54% < 2 PLT150 - 50010/mm< 5 NEU%45 - 80%< 3L YM%25 - 50%< 5 MON% 2 - 10%< 10 EOS% 1 - 5%< 20 BAS%0.5-2.5%< 30CERTIFICATIONEN 61326: 2001IEC 61000-3-2: 2000IEC 61000-3-3: 2001IEC 61010-1: 2001IEC 61010-2-081: 2001IEC 61010-2-101: 2002CE 98/79/EC949 453 0500 • 888 903 5001/medical A D -0 4 0 9 1 3 -1 R e v . 1。

极限挑战第三季20200708背景音乐bgm插曲汇总1.孙红雷上跳楼机前的bgm《没有名字的怪物》2.孙红雷上极速云宵的背景音乐是动漫《从零开始的异世界生活》ED《STYXHELIX》3.张艺兴的箱子在家乐福被孙红雷抢走时的背景音乐《豪杰春香》片尾曲希望你幸福4.黄渤他们上船之后看到那个琵琶女出场时在哼的歌曲《太子妃》BGM5.王讯换新发型的背景音乐是39分那个韩文BGMbigbang的highhigh6.本期出现的BGM文豪野犬的op7.出现的BGM海贼王BGM《dearfriends》8.张艺兴发现自己的箱子又被孙红雷拿走的时候BGM张艺兴《一个人》9.陈家祠出场音乐是排球少年的BGM10.红雷哥上广州塔坐电梯是暗杀教室的bgm11.王旭拿金条的BGM妖精的尾巴BGM12.王讯蹦极哪首背景音乐是极限挑战的主题曲《男人的事》13.机动战士高达独角兽BGM《IntotheSky》14.王迅蹦极时候的BGM是Onepunchman(Recreated)一拳超人里的极限挑战第三季更新时间：2017年7月9日起每周日晚22:00极限挑战第三季一共几期：期数一共12期，每集长度：约90分钟《极限挑战第三季》是上海东方卫视推出的大型励志体验真人秀节目，节目共12期，第三季节目六位固定成员是黄渤、孙红雷、黄磊、罗志祥、王迅、张艺兴。

每期节目都围绕一个社会热点或时代背景而展开，节目中“极限男人帮”体验出租车司机、家政服务等最平凡普通的职业;走在城市街头，与普通百姓“亲密接触”。

每季的归来篇幅也是主创团队最为花心思的，第三季的MC阵容依旧保持不变，并以“无处不在，与你同行”为主题。

首期节目开篇，“颜王”孙红雷和“神算子”黄磊惨被队友出卖，为了避免被劝退而接受一系列艰难的任务。

孙红雷天还没亮就拿起喷水器认真洗车;黄渤骑上三轮车，挨家挨户送酸奶;黄磊王迅天没亮就来到早餐摊炸油条卖豆浆;罗志祥温柔地帮狗狗洗澡，张艺兴小心地替狗狗吹干毛发等等。

Barbed FittingsThe World StandardDubl-Barb FittingsCompact One-piece Economical ReusableUse with Polyethylene Tubing⏹⏹⏹⏹⏹Hose Barb FittingsAll Brass Construction Straight and Metric Threads Beaded & Standard Hose BarbsUse with Hose Clamp Reusable⏹⏹⏹⏹⏹Catalog 3501E Barbed FittingsGAdvantagesCompact one-piece, push-on barbed fitting for a quick, economical way to connect polyethylene tubing. In addition to the styles shown, custom DUBL-BARB fittings to meet your exact requirements are available. Machined from CA 360 or CA 345 brass.ApplicationsBecause of the many available variations in qualities of polyethylene tubing, DUBL-BARB ® fittings are recommended for use with Parker Parflex ® polyethylene tubing (or an equal grade). Parker Parflex® tubing is highly resistant to environmental stress cracking which is necessary for long life when coupled with expansion fittings.Working Pressure and Temperature RangesIn tube sizes 1/4 to 3/8 working pressures up to 150 psi are practical at temperatures ranging from -65° to +90°F on tube size 1/2 working pressures up to 100 psi at temperatures ranging from -65° to +75°F .Assembly Instructions Simply push tube over the two barbs — be sure tubing is cut squarely.OrderBy part number and name.NomenclaturePart numbers are constructed from symbols that identify the style and size of the fitting. The first series of numbers and letters identifies the style and type fitting. The second series of numbers describes the size.SizesT ube sizes are determined by the numbers of sixteenths of an inch in the tube O.D.Special FittingsFitting configurations and/or sizes other than those shown in the catalog can be furnished. It is suggested that a print or sketch be submitted with the inquiry.PricingOnly items priced in current supplementary price list PL3501 are carried in stock. Price and delivery for non-stock items furnished on request for specified quantity.example: 231 –8 –6Run Tee (Tube to male pipe)1/2" (8/16) Tube O.D.3/8" (6/16) Pipe ThreadPlug 20PART TuBe TuBeC NO. O.D.I.D.DIA.LM20-4 1/4 .170 .290 .56 .4120-6 3/8 .250 .390 .68 .4420-8 1/2 .377 .577 .81 .56Plug Adapter 20PART TuBe TuBe TuBe TuBe C NO.O.D. 1 I.D. 1 O.D. 2 I.D. 2DIA.L20-4-5/32 5/32 .096 1/4 .170 .290 .65union 22PART TuBe TuBe FLOW NO.O.D.I.D.LMDIA. D22-5/32 5/32x5/32 .096x.096 .59 .28 .06222-4 1/4x1/4 .170x.170 .84 .41 .12022-6 3/8x3/8 .250x.250 .94 .44 .18722-8 1/2x1/2 .375x.375 1.19 .56 .312union Reducer 22PART TuBe TuBe FLOW NO.O.D.I.D.LMNDIA. D22-4-5/32 1/4x5/32 .170x.096 .72 .41 .28 .06222-4-6 1/4x3/8 .170x.250 .88 .44 .41 .12022-4-8 1/4x1/2 .170x.375 1.06 .56 .41 .12022-6-8 3/8x1/2 .250x.375 1.06 .56 .44 .187Bulkhead union 22BHPART TuBe TuBe ST.C P FLOW BLkHD NO.O.D. I.D.THD.HexMAx.LMDIA. D HOLe DIA.22BH-4-4 1/4 .170 5/16-24 7/16 .219 1.38 .78 .120 5/1622BH-6-6 3/8 .250 3/8-24 7/16 .375 1.63 1.00 .187 3/8union 22CAT ube to Compress-AlignPART TuBe TuBe CA CFLOW NO.O.D. I.D. TuBeHexLMDIA. D22CA-4-4 1/4 .170 1/4 7/16 1.15 .41 .120GBulkhead union 22CABHT ube to Compress-AlignPART TuBe TuBe CA ST.C P FLOW BuLkHeAD NO.O.D. I.D. TuBeTHD.HexMAx.LMDIA. DHOLe DIA.22CABH-4-4 1/4 .170 1/4 5/16-24 7/16 .219 1.53 .78 .120 5/1622CABH-6-6 3/8 .250 3/8 3/8-24 9/16 .375 1.87 1.00 .187 3/8Female Connector 26PART TuBe TuBe PIPe CFLOW NO.O.D. I.D. THReADHexLDIA. D26-5/32-2 5/32 .096 1/8 1/2 .79 .06226-4-2 1/4 .170 1/8 1/2 .91 .12026-6-2 3/8 .250 1/8 1/2 .93 .18726-6-4 3/8 .250 1/4 11/16 1.06 .187Male Connector 27PART TuBe TuBe STRAIgHT CFLOW NO.O.D. I.D. THReADHexLDIA. D27-1* 1/8 .062 10-32 1/4 .61 .05227-2* 1/4 .125 10-32 1/4 .74 .093*For vinyl tubing only.Barb-to-Pipe Adapter 28PART TuBe TuBe TuBe TuBe PIPe C FLOW NO.O.D. 1 I.D. 1 O.D. 2 I.D. 2THD.HexLDIA. D28-4-5/32-2 5/32 .096 1/4 .170 1/8 7/16 1.07 .062Male Connector 28PART TuBe TuBe PIPeC FLOW NO.O.D. I.D.THReADHexLDIA. D28-5/32-2 5/32 .096 1/8 7/16 .84 .06228-4-1 1/4 .170 1/16 3/8 .93 .12028-4-2 1/4 .170 1/8 7/16 .97 .12028-4-4 1/4 .170 1/4 9/16 1.09 .12028-4-10x32* 1/4 .170 10-32 1/4 .71 .09328-6-2 3/8 .250 1/8 7/16 1.00 .18728-6-4 3/8 .250 1/4 9/16 1.13 .18728-8-4 1/2 .375 1/4 9/16 1.25 .31228-8-6 1/2 .375 3/8 11/16 1.28 .31228-8-8 1/2 .375 1/2 7/8 1.44 .312*Straight threadNO. O.D. I.D. THReAD L N DIA. D220-4-2 1/4 .170 1/8 1.50 1.00 .120union Tee 224PART TuBe TuBe FLOWNO. O.D. I.D. L M DIA. D224-5/32 5/32 .096 1.00 .50 .062224-4 1/4 .170 1.25 .63 .120224-6 3/8 .250 1.38 .69 .187224-8 1/2 .375 1.63 .81 .312union Tee 224 Combination SizesPART TuBe TuBe FLOW FLOWNO. O.D. I.D. L M N DIA. D DIA. D1224-4-4-5/32 1/4x5/32 .170x.096 1.25 .63 .50 .120 .062224-6-6-5/32 3/8x5/32 .250x.096 1.38 .69 .50 .187 .062224-6-6-4 3/8x1/4 .250x.170 1.38 .69 .62 .187 .120224-8-8-4 1/2x1/4 .375x.170 1.62 .81 .65 .312 .120224-8-8-6 1/2x3/8 .375x.250 1.62 .81 .69 .312 .187union elbow 225PART TuBe TuBe FLOWNO. O.D. I.D. M DIA. D225-5/32 5/32 .096 .50 .062225-4-4 1/4 .170 .63 .120225-6-6 3/8 .250 .69 .187225-8-8 1/2 .375 .81 .312union elbow 225 Combination SizePART TuBe TuBe TuBe TuBe FLOW FLOW NO. O.D. 1 O.D. 2 I.D. 1 I.D. 2 M1 M2 DIA. D1 DIA. D2 225-4-5/32 1/4 5/32 .170 .096 .63 .50 .120 .062GNO.O.D. I.D. THReADLMNDIA. D228-4-2 1/4 .170 1/8 1.91 .66 .44 .120Male elbow 229PART TuBe TuBe PIPeFLOW NO.O.D. I.D.THReADMNDIA. D229-5/32-2 5/32 .0961/8 .56 .63 .062229-4-1 1/4 .170 1/16 .62 .60 .120229-4-2 1/4 .170 1/8 .69 .63 .120229-4-4 1/4 .170 1/4 .72 .72 .120229-6-2 3/8 .250 1/8 .69 .69 .187229-6-4 3/8 .250 1/4 .75 .75 .187229-8-4 1/2 .375 1/4 .94 .74 .312229-8-6 1/2 .375 3/8 .94 .81 .31290° elbow Barb Adapter 229PART TuBe TuBe TuBe TuBe PIPe FLOW NO.O.D. 1 I.D. 1 O.D. 2 I.D. 2 THReADMDIA. D229-4-5/32-2 5/32 .096 1/4 .170 1/8 .78 .062Female elbow 230PART TuBe TuBe PIPeFLOW NO.O.D. I.D.THReADLMNDIA. D230-4-2 1/4 .170 1/8 .91 .66 .44 .120230-6-4 3/8 .250 1/4 1.12 .78 .63 .187Male Run Tee 231PART TuBe TuBe PIPeFLOW NO.O.D. I.D.THReADLMNDIA. D231-4-2 1/4 .170 1/8 1.28 .66 .69 .120231-6-2 3/8 .250 1/8 1.38 .69 .69 .187231-6-4 3/8 .250 1/4 1.44 .75 .75.187Male Branch Tee 232PART TuBe TuBe PIPe FLOW NO. O.D. I.D. THReAD L M N DIA. D 232-4-1 1/4 .170 1/16 1.33 .66 .65 .120 232-4-2 1/4 .170 1/8 1.38 .69 .66 .120 232-6-2 3/8 .250 1/8 1.38 .69 .69 .187 232-6-4 3/8 .250 1/4 1.50 .75 .75 .187Tee 233PART TuBe TuBe COMB. FLOW NO. O.D. I.D. TuBe L M N DIA. D 233-4-4-4 1/4 .170 1/4 .73 .53 .74 .120 233-6-6-4 1/4 .170 3/8 .87 .59 .80 .120Female Branch Tee 237PART TuBe TuBe PIPe FLOW NO. O.D. I.D. THReAD L M N DIA. D 237-5/32-2 5/32 .096 1/8 1.06 .53 .44 .062 237-4-2 1/4 .170 1/8 1.34 .67 .49 .120Solder Connector 238PART TuBe TuBe FLOW NO. O.D. 1 I.D. 1 L M DIA. D 238-4-4 1/4 .170 .91 .25 .120GAdvantagesAll Parker hose barb fitting pipe threads are made to Dryseal standards. Connectors, unions, nuts and extended elbows and tees are machined from CA 360 and CA 345 brass.Temperature and Working Pressure RangesFrom -40° to +160°F . at 150 PSI maximum.Note: These fittings are intended for use with 97HC hose clamp, similar type clamp or a crimped ferrule.Assembly Instructions1. Cut hose cleanly and squarely to length.2. Slide clamp on hose.3. Lubricate hose. Push hose on fitting until hose bottoms against stop ring or hex.4. Position hose clamp as shown below and secure with a screwdriver or wrench. Maintain “A” dimension noted below for proper clamp positioning.HOSe HOSe SIzeCLAMPA3/16" 97 HC-3 1/4"1/4" 97 HC-3 1/4"5/16" 97 HC-6 1/4"3/8" 97 HC-6 1/8"1/2" 97 HC-8 1/8"5/8" 97 HC-12 1/8"3/4" 97 HC-12 1/8"OrderBy part number and name.NomenclaturePart numbers are constructed from symbols that identify the style and size of the fitting. The first series of numbers and letters identifies the style and type fitting. The second series of numbers describes the size.SizesPipe sizes are determined by the number of sixteenths of an inch in the pipe size.Special FittingsFitting configurations and/or sizes other than those shown in the catalog can be furnished. It is suggested that a print or sketch be submitted with the inquiry.PricingOnly items priced in current supplementary price list PL3501 are carried in stock. Price and delivery for non-stock items furnished on request for specified quantity.example: 125 HBL –6 –4Hose Barb to Male Pipe Hose Barb3/8" (6/16) Hose I.D.1/4" (4/16) NPTF/PTFCatalog 3501EHose Barb FittingsBeaded Hose Barb to Male Pipe 68HBPART I.D. HOSe PIPe CFLOW NO.SIze THReADHexLMDIA.D68HB-6-6 3/8 3/8 11/16 1.53 .78 .28168HB-8-4 1/2 1/4 5/8 1.56 .78 .37568HB-8-6 1/2 3/8 11/16 1.53 .78 .40668HB-8-8 1/2 1/2 7/8 1.73 .78 .40668HB-10-6 5/8 3/8 3/4 1.62 .88 .50168HB-10-8 5/8 1/2 7/8 1.92 .88 .50168HB-12-8 3/4 1/2 7/8 1.98 .88 .56468HB-12-12 3/4 3/4 1 1/16 2.04 .97 .62568HB-16-12 1 3/4 1 1/8 2.12 1.00 .75068HB-16-16 1 1 1.38 2.31 1.00 .812Beaded Hose Barb to SAe Straight Thread 685HBPART I.D. HOSe STRAIgHT C FLOW NO.SIzeTHReAD HexLMDIA.D685HB-4-4 1/4 7/16-20 9/16 1.40 .78 .18685HB-6-4 3/8 7/16-20 9/16 1.39 .78 .18685HB-8-8 1/2 3/4-16 7/8 1.48 .78 .40685HB-10-8 5/8 3/4-16 7/8 1.56 .78 .40685HB-12-8 3/4 3/4-16 7/8 1.75 .97 .40685HB-12-12 3/4 1 1/16-12 1 1/4 1.82 .97 .62685HB-16-8 1 3/4-16 1 1/8 1.79 .97 .40685HB-16-12 1 1 1/16-12 1 1/4 1.99 .97 .62Note: Viton o-ring is standardHose Barb to Metric Adaptor 68HB-x-MIxPART TuBe MeTRIC NuMBeRSIzeTHReADHexLMD68HB-6-MI12 3/8 M12 x 1.5 11/16 1.50 .78 .24 68HB-6-MI14 3/8 M14 1.5 3/4 1.51 .78 .30 68HB-8-MI12 1/2 M12 x 1.5 11/16 1.50 .78 .24Note: Viton o-ring is standardStainless Steel Worm Drive Clamp 97HCPART D C H NO.MAx. MIN.HexMAx.W97HC-3 .62 .25 .25 1.00 .3197HC-6 .87 .38 .31 1.40 .5097HC-8 1.00 .44 .31 1.53 .5097HC-12 1.25 .50 .31 1.80 .50Hose Mender 122HBLPART I.D. HOSe C FLOW NO.SIzeDIA.LMO.D.DIA. D122HB-3* 3/16 5/16 1.44 .69 .227 .125122HBL-4 1/4 3/8 2.00 .97 .290 .187122HBL-5 5/16 7/16 2.00 .97 .353 .250122HBL-6 3/8 1/2 2.00 .97 .415 .281122HBL-8 1/2 5/8 2.00 .97 .530 .375122HBL-12 3/4 7/8 2.00 .97 .790 .562* 3 Barb design.GHose Barb to Male Pipe 125HBPART I.D. HOSe PIPe CFLOW NO.SIze THReADHexLMO.D.DIA. D125HB-2-2 1/8 1/8 7/16 1.07 .50 .185 .093125HB-3-2 3/16 1/8 7/16 1.25 .69 .227 .125125HB-3-4 3/16 1/4 9/16 1.44 .69 .227 .125Hose Barb to Male Pipe 125HBLPART I.D. HOSe PIPe CFLOW NO.SIze THReADHexLMO.D.DIA. D125HBL-4-2 1/4 1/8 7/16 1.54 .97 .290 .187125HBL-4-4 1/4 1/4 9/16 1.72 .97 .290 .187125HBL-4-6 1/4 3/8 11/16 1.77 .97 .290 .187125HBL-5-2 5/16 1/8 7/16 1.54 .97 .353 .250125HBL-5-4 5/16 1/4 9/16 1.72 .97 .353 .250125HBL-5-6 5/16 3/8 11/16 1.77 .97 .353 .250125HBL-6-2 3/8 1/8 7/16 1.54 .97 .415 .281125HBL-6-4 3/8 1/4 9/16 1.72 .97 .415 .281125HBL-6-6 3/8 3/8 11/16 1.77 .97 .415 .281125HBL-6-8 3/8 1/2 7/8 1.97 .97 .415 .281125HBL-8-4 1/2 1/4 9/16 1.72 .97 .530 .375125HBL-8-6 1/2 3/8 11/16 1.77 .97 .530 .375125HBL-8-8 1/2 1/2 7/8 1.97 .97 .530 .375125HBL-8-12 1/2 3/4 1-1/16 1.98 .97 .530 .375125HBL-10-6 5/8 3/8 11/16 1.77 .97 .645 .468125HBL-10-8 5/8 1/2 7/8 1.97 .97 .645 .468125HBL-10-12 5/8 3/4 1-1/16 1.98 .97 .645 .468125HBL-12-8 3/4 1/2 7/8 1.97 .97 .790 .562125HBL-12-12 3/4 3/4 1-1/16 1.98 .97 .790 .562125HBL-16-12 1 3/4 1-1/16 2.18 1.17 1.02 .750125HBL-16-16 1 1 1-3/8 2.36 1.17 1.02 .875Male Swivel Hose Barb 125HBLSVPART I.D. HOSe PIPe CFLOW NO.SIze THReADHexLMO.D.DIA. D125HBLSV-4-4 1/4 1/4 11/16 2.14 .97 .290 .187125HBLSV-6-4 3/8 1/4 11/16 2.14 .97 .415 .250125HBLSV-6-6 3/8 3/8 11/16 2.14 .97 .415 .250125HBLSV-8-8 1/2 1/2 7/8 2.48 .97 .530 .375Hose Barb to Female Pipe 126HBLPART I.D. HOSe PIPe CFLOW NO.SIze THReADHexLMO.D.DIA. D126HBL-4-2 1/4 1/8 1/2 1.47 .97 .290 .187126HBL-4-4 1/4 1/4 11/16 1.58 .97 .290 .187126HBL-5-4 5/16 1/4 11/16 1.58 .97 .353 .250126HBL-6-2 3/8 1/8 1/2 1.47 .97 .415 .281126HBL-6-4 3/8 1/4 11/16 1.58 .97 .415 .281126HBL-6-6 3/8 3/8 13/16 1.63 .97 .415 .281126HBL-8-6 1/2 3/8 13/16 1.59 .97 .530 .375126HBL-8-8 1/2 1/2 1 1.73 .97 .530 .375126HBL-12-12 3/4 3/4 1-1/4 1.92 .97 .790 .562Ball-end Joint Adapter to Male Pipe 127HBFor use with 128HBLSVMALe MALePART N.P.S.M. N.P.T. C FLOWNO. THReAD THReAD Hex L DIA. D127HB-4-2 1/4 1/8 9/16 .91 .219127HB-4-4 1/4 1/4 9/16 1.10 .281127HB-6-4 3/8 1/4 11/16 1.10 .312127HB-6-6 3/8 3/8 11/16 1.15 .406127HB-8-6 1/2 3/8 7/8 1.25 .406127HB-8-8 1/2 1/2 7/8 1.50 .531Hose Barb to Swivel Female Ball-end 128HBLSVI.D. FeMALePART HOSe N.P.S.M. C FLOW NO. SIze THReAD Hex L M O.D. DIA. D 128HBLSV-4-4 1/4 1/4 5/8 1.50 .97 .290 .187 128HBLSV-5-4 5/16 1/4 5/8 1.50 .97 .353 .250 128HBLSV-6-4 3/8 1/4 5/8 1.63 .97 .415 .250 128HBLSV-6-6 3/8 3/8 3/4 1.50 .97 .415 .281 128HBLSV-8-8 1/2 1/2 29/32 1.52 .97 .530 .375Hose Barb 90° elbow to Male Pipe 129HBPART I.D. HOSe PIPe FLOW NO. SIze THReAD L M N O.D. DIA. D 129HB-3-2 3/16 1/8 .97 .69 .66 .227 .173 129HB-4-2 1/4 1/8 1.04 .76 .66 .290 .187 129HB-4-4 1/4 1/4 1.06 .76 .86 .290 .187 129HB-4-6 1/4 3/8 1.30 .76 .84 .290 .187 129HB-5-2 5/16 1/8 1.06 .76 .66 .353 .234 129HB-5-4 5/16 1/4 1.12 .76 .84 .353 .234 129HB-5-6 5/16 3/8 1.19 .76 .84 .353 .234 129HB-6-2 3/8 1/8 1.32 .97 .94 .415 .281 129HB-6-4 3/8 1/4 1.32 .97 .94 .415 .281 129HB-6-6 3/8 3/8 1.50 .97 1.06 .415 .281 129HB-6-8 3/8 1/2 1.52 .97 1.25 .415 .281 129HB-8-4 1/2 1/4 1.53 .97 1.06 .530 .375 129HB-8-6 1/2 3/8 1.53 .97 1.06 .530 .375 129HB-8-8 1/2 1/2 1.53 .97 1.25 .530 .375 129HB-12-12 3/4 3/4 1.33 .79 1.27 .790 .562Hose Barb elbow to SAe Straight Thread 1295HBPART I.D. HOSe STRAIgHT B FLOW NO. SIze THReAD Hex L M O.D. DIA. D 1295HB-6-6 3/8 9/16-18 11/16 1.10 1.11 .410 .270 Note: Viton o-ring is standardHose Barb 45° elbow to Male Pipe 139HBPART I.D. HOSe PIPe FLOW NO. SIze THReAD L M N O.D. DIA. D 139HB-4-2 1/4 1/8 .91 .76 .68 .290 .187 139HB-4-4 1/4 1/4 1.00 .76 .68 .290 .187 139HB-6-4 3/8 1/4 1.00 .76 .68 .415 .281GHose Barb to Swivel 45° Female Flare 146HBLFSVPART I.D. HOSe STRAIgHT CFLOW NO.SIze THReADHexLMO.D.DIA. D146HBLFSV-4-4 1/4 7/16-20 9/16 1.55 .97 .290 .187146HBLFSV-4-6 1/4 5/8-18 3/4 1.72 .97 .290 .187146HBLFSV-6-6 3/8 5/8-18 3/4 1.72 .97 .415 .281Beaded Hose Barb elbow to SAe Straight Thread 1695HBPART HOSe STRAIgHT NuMBeRSIzeTHReADHexLMND1695HB-6-4 3/8 7/16-20 9/16 1.09 .78 1.10 .181695HB-8-6 1/2 9/16-18 9/16 1.10 .78 1.11 .301695HB-8-8 1/2 3/4-16 7/8 1.28 .78 1.47 .401695HB-10-8 5/8 3/4-16 7/8 1.47 .88 1.47 .401695HB-10-10 5/8 7/8-14 1 1.41 .88 1.60 .501695HB-12-8 3/4 3/4-16 7/8 1.47 .97 1.47 .401695HB-12-10 3/4 7/8-14 1 1.60 .97 1.62 .501695HB-12-12 3/4 1 1/16-12 1 1.60 .97 1.64 .621695HB-16-12 1 1 1/16-12 1 1/4 1.60 .97 1.75 .60Note: Viton o-ring is standardBeaded elbow to Metric Adaptor 169HB-x-MIxPART HOSe MeTRIC NuMBeRSIzeTHReADHexLMND169HB-10-MI27 5/8 M27 x 2.0 7/8 1.41 .78 1.63 .50169HB-16-MI27 1 M27 x 2.0 1 1.67 .97 1.68 .71169HB-16-MI33 1 M33 x 2.0 1 5/16 1.75 .97 1.90 .84Note: Viton o-ring is standardHose Barb Tee to SAe Straight Thread 1725HBPART I.D. HOSe STRAIgHT BFLOW NO.SIze THReADHexLMO.D.DIA. D1725HB-6-6 3/8 9/16-18 11/16 2.20 1.10 .420 .280Note: Viton o-ring is standardHose Barb Tee to Male Pipe 171HBPART I.D. HOSe PIPeFLOW NO.SIze THReADLL1MNO.D. DIA. D171HB-4-4 1/4 1/4 1.10 .85 .76 1.10 .290.187Beaded Hose Barb 45° elbow Tube to Male Pipe 179HBPART I.D. HOSe NPTF CFLOW NO.SIze THReAD HexLMNO.D. DIA. D179HB-6-4 3/8 1/4-18 .75 1.09 .78 .93 .45 .28179HB-6-6 3/8 3/8-18 .75 1.09 .78 .93 .45 .28179HB-10-8 5/8 1/2-14 .81 1.19 .78 1.13 .70 .50179HB-12-8 3/4 1/2-14 .81 1.19 .78 1.13 .83 .56Beaded Hose Barb 45° elbow Tube to Straight Thread 1795HBPART I.D. HOSe STRAIgHT CFLOW NO.SIze THReAD HexLMNDIA. D1795HB-8-8 1/2 3/4-16 7/8 1.12 .78 1.16 .4001795HB-10-8 5/8 3/4-16 7/8 1.22 .88 1.16 .3981795HB-12-8 3/4 3/4-16 7/8 1.22 .88 1.16 .3981795HB-12-12 3/4 1 1/16-12 1 1/4 1.35 .97 1.65 .6201795HB-16-12 1 1 1/16-12 1 1/4 1.38 .97 1.47 .6201795HB-16-14 1 1 3/16-12 1 3/8 1.25 .97 1.80 .720Note: Viton o-ring is standardBeaded Hose Barb 45 elbow to Metric Thread 179HB-x-MIxPART HOSe MeTRIC NuMBeRSIzeTHReADHexLMND179HB-12-MI18 3/4 M18 x 1.5 13/16 1.15 .78 1.16 .44179HB-16-MI27 1 M27 x 2.0 1 1/16 1.51 .97 1.71 .71Note: Viton o-ring is standardBeaded Hose Barb 90° elbow Tube to Male Pipe 269HBPART I.D. HOSe PIPeFLOW NO.SIze THReADLMNDIA. D269HB-6-6 3/8 3/8 1.19 .78 .88 .281 269HB-8-4 1/2 1/4 1.16 .78 .99 .310269HB-8-6 1/2 3/8 1.16 .78 1.08 .406 269HB-8-8 1/2 1/2 1.28 .78 1.25 .406 269HB-10-4 5/8 1/4 1.13 .78 .99 .312269HB-10-6 5/8 3/8 1.16 .78 .99 .406269HB-10-8 5/8 1/2 1.28 .78 1.25 .501 269HB-12-8 3/4 1/2 1.28 .78 1.25 .625269HB-12-12 3/4 3/4 1.33 .78 1.27 .625Beaded Hose Barb 45° elbow Tube to Male Pipe 279HBPART I.D. HOSe NPTF CFLOW NO.SIze THReAD HexLMNO.D. DIA. D279HB-16-12 1 3/4-14 1.12 1.38 .97 1.13 1.06.720。