机械常用语英文

机械专业英语词汇1.Manufacturing Technology：加工技术。

2.Friction：摩擦。

3.Automated Manufacturing：自动制造。

4.Turning：车削。

ling：铣削。

6.Grinding：磨削。

7.Machine Tool：机床。

8.Casting：铸造。

9.Forging：锻造。

10.Welding：焊接。

11.Brazing：钎焊。

12.Heat Treatment：热处理。

13.Pressure Die Casting：压铸。

C Machining：数控加工。

ser Cutting：激光切割。

16.NC Turning：数控车削。

17.NC Milling：数控铣削。

18.NC Grinding：数控磨削。

21.Robotic Machining：机器人加工。

22.Industrial Robots：工业机器人。

23.Robot Programming：机器人编程。

24.Robot Simulation：机器人仿真。

25.Robot Control：机器人控制。

26.Robot Navigation：机器人导航。

27.Robot Vision：机器人视觉。

28.Sensors：传感器。

29.Drive Technology：传动技术。

30.Actuator：执行器。

31.Transmission：传动。

32.Gearing：齿轮传动。

33.Coupling：联轴器。

34.Bearings：轴承。

35.AC Motors：交流电动机。

36.DC Motors：直流电动机。

37.Servo Motors：伺服电动机。

38.Pneumatics：气动。

39.Hydraulics：液压。

40.Automation：自动化。

41.Motion Control：运动控制。

42.PID Control：比例积分微分控制。

43.Control Systems：控制系统。

机械术语中英文对照汇编引言在机械领域中，掌握各种机械术语的中英文对照是非常重要的。

具备这样的知识可以更好地理解和沟通机械工程方面的知识。

本文将介绍一些常见的机械术语的中英文对照，以帮助读者更好地掌握这个领域。

一、机械部件及装置1.齿轮（Gear）2.轴（Shaft）3.轴承（Bearing）4.皮带（Belt）5.键槽（Keyway）6.轴套（Sleeve）7.螺母（Nut）8.螺栓（Bolt）9.泵（Pump）10.阀门（Valve）二、机械运动1.旋转（Rotation）2.平移（Translation）3.倾斜（Tilt）4.摩擦（Friction）5.惯性（Inertia）6.阻尼（Damping）7.弹簧（Spring）8.螺旋（Spiral）三、机械工艺1.钻孔（Drilling）2.铣削（Milling）3.车削（Turning）4.切削（Cutting）5.焊接（Welding）6.铆接（Riveting）7.雕刻（Engraving）8.抛光（Polishing）9.喷涂（Spraying）四、机械力学1.力（Force）2.加速度（Acceleration）3.速度（Velocity）4.质量（Mass）5.惯性力（Inertial Force）6.弹性力（Elastic Force）7.重力（Gravity）8.摩擦力（Frictional Force）9.引力（Tension）10.动量（Momentum）五、机械精度1.公差（Tolerance）2.精度（Precision）3.粗糙度（Roughness）4.轴向（Axial）5.径向（Radial）6.径向间隙（Radial Clearance）7.齿间隙（Backlash）8.平行度（Parallelism）9.垂直度（Perpendicularity）10.同心度（Concentricity）六、机械测量1.量程（Range）2.精度（Accuracy）3.分度（Resolution）4.零偏（Offset）5.示值误差（Indication Error）6.重复性（Repeatability）7.稳定性（Stability）8.灵敏度（Sensitivity）七、机械维护1.保养（Maintenance）2.润滑（Lubrication）3.换油（Oil Change）4.更换零件（Parts Replacement）5.检修（Overhaul）6.清洁（Cleaning）7.校准（Calibration）8.故障排除（Troubleshooting）结论以上是一些常见的机械术语的中英文对照。

组装、冲压、喷漆等专业词汇Assembly line 组装线Layout 布置图Conveyer流水线物料板Rivet table 拉钉机Rivet gun 拉钉枪Screw driver 起子Electric screw driver 电动起子Pneumatic screw driver 气动起子worktable 工作桌OOBA 开箱检查fit together 组装在一起fasten 锁紧( 螺丝)fixture 夹具(治具) pallet 栈板barcode 条码barcode scanner 条码扫描器fuse together 熔合fuse machine 热熔机repair 修理operator 作业员QC 品管supervisor 课长ME 制造工程师MT 制造生技cosmetic inspect 外观检查inner parts inspect 内部检查thumb screw 大头螺丝lbs. inch 镑、英寸EMI gasket 导电条front plate 前板rear plate 后板chassis 基座bezel panel 面板power button 电源按键reset button 重置键Hi-pot test of SPS 高源高压测试Voltage switch of SPS 电源电压接拉键sheet metal parts 冲件plastic parts 塑胶件SOP 制造作业程序material check list 物料检查表work cell 工作间trolley 台车carton 纸箱sub-line 支线left fork 叉车personnel resource department 人力资源部production department 生产部门planning department 企划部QC Section 品管科stamping factory 冲压厂painting factory 烤漆厂molding factory 成型厂common equipment 常用设备uncoiler and straightener 整平机punching machine 冲床robot 机械手hydraulic machine 油压机lathe 车床planer |'plein| 刨床miller 铣床grinder 磨床driller 钻床linear cutting 线切割electrical sparkle 电火花welder 电焊机staker=reviting machine 铆合机position 职务president 董事长general manager 总经理special assistant manager 特助factory director 厂长department director 部长deputy manager | =vice manager 副理section supervisor 课长deputy section supervisor =vicesection superisor 副课长group leader/supervisor 组长line supervisor 线长assistant manager 助理to move, to carry, to handle 搬运be put in storage 入库pack packing 包装to apply oil 擦油to file burr 锉毛刺final inspection 终检to connect material 接料to reverse material 翻料wet station 沾湿台Tiana 天那水cleaning cloth 抹布to load material 上料to unload material 卸料to return material/stock to 退料scraped |'skræpid| 报废scrape ..v. 刮;削deficient purchase 来料不良manufacture procedure 制程deficient manufacturing procedure制程不良oxidation |' ksi'dein| 氧化scratch 刮伤dents 压痕defective upsiding down 抽芽不良defective to staking 铆合不良embedded lump 镶块feeding is not in place 送料不到位stamping-missing 漏冲production capacity 生产力education and training 教育与训练proposal improvement 提案改善spare parts=buffer 备件forklift 叉车trailer=long vehicle 拖板车compound die 合模die locker 锁模器pressure plate=plate pinch 压板bolt 螺栓name of a department 部门名称administration/general affairs dept 总务部automatic screwdriver 电动启子thickness gauge 厚薄规gauge(or jig) 治具power wire 电源线buzzle 蜂鸣器defective product label 不良标签identifying sheet list 标示单screwdriver holder 起子插座pedal 踩踏板stopper 阻挡器flow board 流水板hydraulic handjack 油压板车forklift 叉车pallet 栈板glove(s) 手套glove(s) with exposed fingers 割手套thumb 大拇指forefinger 食指midfinger 中指ring finger 无名指little finger 小指band-aid 创可贴iudustrial alcohol 工业酒精alcohol container 沾湿台head of screwdriver 起子头sweeper 扫把mop 拖把vaccum cleaner 吸尘器rag 抹布garbage container 灰箕garbage can 垃圾箱garbage bag 垃圾袋chain 链条jack 升降机productionline 流水线chain 链条槽magnetizer 加磁器lamp holder 灯架to mop the floor 拖地to clean the floor 扫地to clean a table 擦桌子air pipe 气管packaging tool 打包机packaging 打包missing part 漏件wrong part 错件excessive defects 过多的缺陷critical defect 极严重缺陷major defect 主要缺陷minor defect 次要缺陷not up to standard 不合规格dimension/size is a little bigger 尺寸偏大( 小)cosmetic defect 外观不良slipped screwhead/slippery screw head 螺丝滑头slipped screwhead/shippery screw thread 滑手speckle 斑点mildewed=moldy=mouldy 发霉rust 生锈deformation 变形burr( 金属)flash( 塑件)毛边poor staking 铆合不良excesssive gap 间隙过大grease/oil stains 油污inclusion 杂质painting peel off 脏污shrinking/shrinkage 缩水mixed color 杂色scratch 划伤poor processing 制程不良poor incoming part 事件不良fold of pakaging belt 打包带折皱painting make-up 补漆discoloration 羿色water spots 水渍polishing/surface processing 表面处理exposed metal/bare metal 金属裸露lack of painting 烤漆不到位safety 安全quality 品质delivery deadline 交货期cost 成本engineering 工程die repair 模修enterprise plan = enterpriseexpansion projects 企划QC 品管die worker 模工production, to produce 生产equipment 设备to start a press 开机stop/switch off a press 关机classification 整理regulation 整顿cleanness 清扫conservation 清洁culture 教养qualified products, up-to-gradeproducts 良品defective products, not up-to-gradeproducts 不良品waste 废料board 看板feeder 送料机sliding rack 滑料架defective product box 不良品箱die change 换模to fix a die 装模to take apart a die 拆模to repair a die 修模packing material 包材basket 蝴蝶竺plastic basket 胶筐isolating plate baffle plate; barricade 隔板carton box 纸箱to pull and stretch 拉深to put material in place, to cut material, to input 落料to impose lines 压线to compress, compressing 压缩character die 字模to feed, feeding 送料transportation 运输(be)qualfied, up to grade 合格not up to grade, not qualified 不合格material change, stock change 材料变更feature change 特性变更evaluation 评估prepare for, make preparations for准备parameters 参数rotating speed, revolution 转速manufacture management 制造管理abnormal handling 异常处理production unit 生产单位lots of production 生产批量steel plate 钢板roll material 卷料manufacture procedure 制程operation procedure 作业流程to revise, modify 修订to switch over to, switch---tothrow--over switching over 切换engineering, project difficulty工程瓶颈stage die 工程模automation 自动化to stake, staking, reviting 铆合add lubricating oil 加润滑油shut die 架模shut height of a die 架模高度analog-mode device 类模器die lifter 举模器argon welding 氩焊vocabulary for stamping冲压常词汇stamping, press 冲压punch press, dieing out press 冲床uncoiler & strainghtener 整平机feeder 送料机rack, shelf, stack 料架cylinder 油缸robot 机械手taker 取料机conveyer belt 输送带transmission rack 输送架top stop 上死点bottom stop 下死点one stroke 一行程inch 寸动to continue, cont. 连动to grip(material) 吸料location lump, locating piece, block stop 定位块reset 复位smoothly 顺利dent 压痕scratch刮伤deformation 变形filings 铁削to draw holes 抽孔inquiry, search for 查寻to stock, storage, in stock 库存receive 领取approval examine and verify 审核processing, to process 加工delivery, to deliver 交货to return delivenry to.to send delinery backto retrn of goods 退货registration 登记registration card 登记卡to control 管制to put forward and hand in 提报safe stock 安全库存acceptance = receive 验收to notice 通知application form for purchase 请购单consume, consumption 消耗to fill in 填写abrasion 磨损reverse angle = chamfer 倒角character die 字模to collect, to gather 收集failure, trouble 故障statistics 统计demand and supply 需求career card 履历卡to take apart a die 卸下模具to load a die 装上模具to tight a bolt 拧紧螺栓to looser a bolt 拧松螺栓to move away a die plate 移走模板easily damaged parts 易损件standard parts 标准件breaking.(be)broken,(be)cracked断裂to lubricate 润滑common vocabulary for dieengineering 模具工程常用词汇die 模具figure file, chart file 图档cutting die, blanking die 冲裁模progressive die, follow (-on)die连续模compound die 复合模punched hole 冲孔panel board 镶块to cutedges=side cut=side scrap 切边to bending 折弯to pull, to stretch 拉伸Line streching, line pulling 线拉伸engraving, to engrave 刻印upsiding down edges 翻边to stake 铆合designing, to design 设计design modification 设计变化die block 模块folded block 折弯块sliding block 滑块location pin 定位销lifting pin 顶料销die plate, front board 模板padding block 垫块stepping bar 垫条upper die base 上模座lower die base 下模座upper supporting blank 上承板upper padding plate blank 上垫板spare dies 模具备品spring 弹簧bolt 螺栓document folder 文件夹file folder 资料夹to put file in order 整理资料spare tools location 手工备品仓first count 初盘人first check 初盘复棹人second count 复盘人second check 复盘复核人equipment 设备waste materials 废料work in progress product 在制品casing = containerazation 装箱quantity of physical invetory secondcount 复盘点数量quantity of customs count会计师盘,点数量thefirst page 第一联filed by accounting department forreference 会计部存查end-user/using unit(department) 使用单位summary of year-end physicalinventory bills年终盘点截止单据汇总表bill name 单据名称This sheet and physical inventorylist will be sent to accountingdepartment together (Those of NHKwill be sent to financialdepartment)本表请与盘点清册一起送会计部－(NHK 厂区送财会部)Application status records ofyear-end physical inventory List andphysical inventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO.空白与作废单号plate 电镀mold成型material for engineering mold testing 工程试模材料not included in physical inventory 不列入盘点sample 样品incoming material to be inspected 进货待验description 品名steel/rolled steel 钢材material statistics sheet物料统计明细表meeting minutes 会议记录meeting type 会别distribution department 分发单位location 地点chairman 主席present members 出席人员subject 主题conclusion 结论decision items 决议事项responsible department 负责单位pre-fixed finishing date预定完成日approvedby / checked by /prepared by 核准/审核/ 承办PCE assembly production schedulesheetPCE 组装厂生产排配表model 机锺workorder 工令revision 版次remark 备注production control confirmation 生产确认checked by 初审approved by 核准department 部门stock age analysis sheet库存货龄分析表on-hand inventory 现有库存available material 良品可使用obsolete material 良品已呆滞to be inspected or reworked待验或重工total 合计cause description 原因说明part number/ P/N 料号type 形态item/group/class 类别quality 品质preparedby 制表notes 说明year-end physical inventorydifference analysis sheet年终盘点差异分析表physical inventory 盘点数量physical count quantity 帐面数量difference quantity 差异量cause analysis 原因分析raw materials 原料materials 物料finished product 成品semi-finished product 半成品packing materials 包材good product/accepted goods/ accepted parts/good parts 良品defective product/non-good parts 不良品disposed goods 处理品warehouse/hub 仓库on way location 在途仓oversea location 海外仓spare parts physical inventory list 备品盘点清单spare molds location 模具备品仓skid/pallet 栈板tox machine 自铆机wire EDM 线割EDM 放电机coil stock 卷料sheet stock 片料tolerance 工差score=groove 压线cam block 滑块pilot 导正筒trim 剪外边pierce剪内边drag form压锻差pocket for the punch head 挂钩槽slug hole 废料孔feature die 公母模expansion dwg 展开图radius 半径shim(wedge)楔子torch-flame cut 火焰切割set screw 止付螺丝form block 折刀stop pin 定位销round pierce punch=die button 圆冲子shape punch=die insert 异形子stock locater block 定位块under cut=scrap chopper 清角active plate 活动板baffle plate 挡块cover plate 盖板male die 公模female die 母模groove punch 压线冲子air-cushion eject-rod 气垫顶杆spring-box eject-plate 弹簧箱顶板bushing block 衬套insert 入块club car 高尔夫球车capability 能力parameter 参数factor 系数phosphate 皮膜化成viscosity 涂料粘度alkalidipping 脱脂main manifold 主集流脉bezel 斜视规blanking 穿落模dejecting 顶固模demagnetization 去磁;消磁high-speed transmission 高速传递heat dissipation 热传rack 上料degrease 脱脂rinse 水洗alkaline etch 龄咬desmut 剥黑膜D.I. rinse 纯水次Chromate 铬酸处理Anodize 阳性处理seal 封孔revision 版次part number/P/N 料号good products 良品scraped products 报放心品defective products 不良品finished products 成品disposed products 处理品barcode 条码flow chart 流程表单assembly 组装stamping 冲压molding 成型spare parts=buffer 备品coordinate 座标dismantle the die 折模auxiliary fuction 辅助功能poly-line 多义线heater band 加热片thermocouple 热电偶sand blasting 喷沙grit 砂砾derusting machine 除锈机degate 打浇口dryer 烘干机induction 感应induction light 感应光response=reaction=interaction 感应ram 连杆edge finder 巡边器concave 凸convex 凹short 射料不足nick 缺口speck 瑕??shine 亮班splay 银纹gas mark 焦痕delamination 起鳞cold slug 冷块blush 导色gouge 沟槽;凿槽satin texture 段面咬花witness line 证示线patent 专利grit 沙砾granule=peuet=grain 细粒grit maker 抽粒机cushion 缓冲magnalium 镁铝合金magnesium 镁金metal plate 钣金lathe 车mill 锉plane 刨grind 磨drill铝boring镗blinster 气泡fillet 镶;嵌边through-hole form 通孔形式voller pin formality 滚针形式cam driver 铡楔shank 摸柄crank shaft 曲柄轴augular offset 角度偏差velocity 速度production tempo 生产进度现状torque 扭矩spline=the multiple keys 花键quenching 淬火tempering 回火annealing 退火carbonization 碳化alloy 合金tungsten high speed steel 钨高速的moly high speed steel 钼高速的organic solvent 有机溶剂bracket 小磁导liaison 联络单volatile 挥发性resistance 电阻ion 离子titrator滴定仪beacon警示灯coolant 冷却液crusher 破碎机模具工程类plain die 简易模pierce die 冲孔模forming die 成型模progressive die 连续模gang dies 复合模shearing die 剪边模riveting die 铆合模pierce 冲孔forming 成型(抽凸,冲凸)draw hole 抽孔bending 折弯trim 切边emboss 凸点dome 凸圆semi-shearing 半剪stamp mark 冲记号deburr or coin 压毛边punch riveting 冲压铆合side stretch 侧冲压平reel stretch 卷圆压平groove 压线blanking 下料stamp letter 冲字( 料号) shearing 剪断tick-mark nearside 正面压印tick-mark farside 反面压印冲压名称类extension dwg 展开图procedure dwg 工程图die structure dwg 模具结构图material 材质material thickness 料片厚度factor 系数upward 向上downward 向下press specification 冲床规格die height range 适用模高die height 闭模高度burr 毛边gap 间隙weight 重量total wt. 总重量punch wt. 上模重量五金零件类inner guiding post 内导柱inner hexagon screw 内六角螺钉dowel pin 固定销coil spring 弹簧lifter pin 顶料销eq-height sleeves=spool 等高套筒pin 销lifter guide pin 浮升导料销guide pin 导正销wire spring 圆线弹簧outer guiding post 外导柱stop screw 止付螺丝located pin 定位销outer bush 外导套模板类top plate 上托板（顶板）top block 上垫脚punch set 上模座punch pad 上垫板punch holder 上夹板stripper pad 脱料背板up stripper 上脱料板male die 公模(凸模)feature die 公母模female die 母模(凹模)upper plate 上模板lower plate 下模板die pad 下垫板die holder 下夹板die set 下模座bottom block 下垫脚bottom plate 下托板(底板) stripping plate 内外打(脱料板) outer stripper 外脱料板inner stripper 内脱料板lower stripper 下脱料板零件类punch 冲头insert 入块( 嵌入件) deburring punch 压毛边冲子groove punch 压线冲子stamped punch 字模冲子round punch 圆冲子special shape punch 异形冲子bending block 折刀roller 滚轴baffle plate 挡块located block 定位块supporting block for location定位支承块air cushion plate 气垫板air-cushion eject-rod 气垫顶杆trimming punch 切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch 压筋冲子reel-stretch punch 卷圆压平冲子guide plate 定位板sliding block 滑块sliding dowel block 滑块固定块active plate 活动板lower sliding plate 下滑块板upper holder block 上压块upper mid plate 上中间板spring box 弹簧箱spring-box eject-rod 弹簧箱顶杆spring-box eject-plate 弹簧箱顶板bushing bolck 衬套cover plate 盖板guide pad 导料块塑件& 模具相关英文compre sion molding 压缩成型flash mold 溢流式模具plsitive mold 挤压式模具split mold 分割式模具cavity 型控母模core 模心公模taper 锥拔leather cloak 仿皮革shiver 饰纹flow mark 流痕welding mark 溶合痕post screw insert 螺纹套筒埋值self tapping screw 自攻螺丝striper plate 脱料板piston 活塞cylinder 汽缸套chip 细碎物handle mold 手持式模具移转成型用模具encapsulation molding 低压封装成型射出成型用模具two plate 两极式（模具）well type 蓄料井insulated runner 绝缘浇道方式hot runner 热浇道runner plat 浇道模块valve gate 阀门浇口band heater 环带状的电热器spindle 阀针spear head 刨尖头slag well 冷料井cold slag 冷料渣air vent 排气道h=0.02~0.05mmw=3.2mmL=3~5mmwelding line 熔合痕eject pin 顶出针knock pin 顶出销return pin 回位销反顶针sleave 套筒stripper plate 脱料板insert core 放置入子runner stripper plate 浇道脱料板guide pin 导销eject rod (bar) （成型机）顶业捧subzero 深冷处理three plate 三极式模具runner system 浇道系统stress crack 应力电裂orientation 定向sprue gate 射料浇口，直浇口nozzle 射嘴sprue lock pin 料头钩销(拉料杆)slag well 冷料井side gate 侧浇口edge gate 侧缘浇口tab gate 搭接浇口film gate 薄膜浇口flash gate 闸门浇口slit gate 缝隙浇口fan gate 扇形浇口dish gate 因盘形浇口H=F=1/2t~1/5tT=2.5~3.5mmdiaphragm gate 隔膜浇口ring gate 环形浇口subarine gate 潜入式浇口tunnel gate 隧道式浇口pin gate 针点浇口Φ0.8~1.0mmRunner less 无浇道(sprue less) 无射料管方式long nozzle 延长喷嘴方式sprue 浇口;溶渣检人员CP capability index 能力指数报告品质人员名称类QC quality control 品质管理人员FQC final quality control 终点品质管制人员IPQC in process quality control 制程中的品质管制人员OQC output quality control 最终出货品质管制人员IQC incoming quality control 进料品质管制人员TQC total quality control 全面质量管理POC passage quality control 段QA quality assurance 质量保证人员OQA output quality assurance出货质量保证人员QE quality engineering 品质工程人员品质保证类FAI first article inspection 新品首件检查FAA first article assurance 首件确认TVR tool verification report 模具确认报告3B 3B 模具正式投产前确认CPK capability index of process模具制程能力参数SSQA standardized supplierquality 合格供应商品质评估OOBA out of box audit 开箱检查QFD quality function deployment品质机能展开FMEA failure model effectivenessanalysis 失效模式分析8 disciplines 8 项回复内容FA final audit 最後一次稽核CAR corrective action request 改正行动要求corrective action report 改正行动FQC 运作类AQL Acceptable Quality Level运作类允收品质水准S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的AOQ Average Output Quality 平均出厂品质AOQL Average Output QualityLevel 平均出厂品质Q/R/S Quality/Reliability/Service 品质/可靠度服务MIL-STD Military-Standard 军用标准S I-S IV Special I-Special IV 特殊抽样水准等级统计制程管制SQC Statistical Quality Control统计品质管制R Range 全距AR Averary Range 全距平均值UCL Upper Central Limit 管制上DIM Dimension 尺寸DIA Diameter 直径FREQ Frequency 频率N Number 样品数其它品质术语类QCC Quality Control Circle 品质TQM Total Quality Management全面品质管理MRB Material Reject Bill 退货单LQL Limiting Quality Level 最低品质水准RMA Return Material Audit 退料P/N Part Number 料号限圈认可L/N Lot Number 特采LCL Lower Central Limit 管制下QIT Quality Improvement Team QAN Quality Amelionrate NoticeAOD Accept On Deviation 特采UAI Use As It 首件检查报告FPIR First Piece Inspection Report 百万分之一PPM Percent Per Million 批号制程统计品管专类SPC Statistical Process Control 限MAX Maximum 最大值MIN Minimum 最小值GRR GaugeReproducibility&Repeatability 量具之再制性及重测性判断量可靠与否品质改善小组PDCA Plan Do Check Action 计划执行检查总结ZD Zero Defect 零缺点QI Quality Improvement 品质改善QP Quality Policy 目标方针品质改善活动ADM Absolute DimensionMeasuremat 全尺寸测量QT Quality Target 品质目标7QCTools 7 Quality Controll Tools品管七大手法通用之件类ECN Engineering Change Notes 工程变更通知(供应商)ECO Engineering Change Order 工程改动要求(客户)PCN Process Change Notice 工序改动通知PMP Product Management Plan 生产管制计划SIP Specification In Process 制程检验规格SOP Standard Operation Procedure 制造作业规范IS Inspection Specification 成品检验规范BOM Bill Of Material 物料清单PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类QC Quality System 品质系统ES Engineering Standarization工程标准CGOO China General PCE 龙华厂文件H Huston (美国)休斯敦CCompaq (美国)康伯公司C China 中国大陆A Assembly 组装(厂)S Stamping 冲压(厂)P Painting 烤漆(厂)I Intel 英特尔公司T TAIWAN 台湾IWS International WorkmanStandard 工艺标准ISO International StandardOrganization 国际标准化组织GS General Specification 一般规格CMCS C-China M-ManufactC-Compaq S-Stamping Compaq产品在龙华冲压厂制造作业规范CQCA Q-Quality A-AssemblyCompaq 产品在龙华组装厂品管作业规范CQCP P-Painting Compaq 产品在龙华烤漆厂品管作业规范部类PMC Production & MaterialControl 生产和物料控制PPC Production Plan Control 生产计划控制MC Material Control 物料控制ME Manafacture Engineering 制造工程部PE Project Engineering 产品工程部A/C Accountant Dept 会计部P/A Personal & Administration人事行政部DC Document Center 资料中心PCS Pieces 个(根,块等) Manufacture 原设备制造 A.S.A.P As Soon As Possible 尽QE Quality Engineering 品质工程PRS Pairs 双(对等) PCE Personal Computer 可能快的(部) CTN Carton 卡通箱Enclosure 个人电脑外设E-MAIL Electrical-Mail 电子邮件QA Quality Assurance 品质保证PAL Pallet/skid 栈板PC Personal Computer 个人电N/A Not Applicable 不适用(处) PO Purchasing Order 采购订单脑QTY Quantity 数量QC Quality Control 品质管制(课) MO Manufacture Order 生产单CPU Central Processing Unit 中VS 以及PD Product Department 生产部LAB Labratry 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部P Painting 烤漆(厂)A Asssembly 组装(厂)S Stamping 冲压(厂)生产类D/C Date Code 生产日期码ID/C Identification Code ( 供应商)识别码SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号其它OEM Original Equipment央处理器SECC SECC` 电解片SGCC SGCC 热浸镀锌材料NHK North of Hongkong 中国大陆PRC People's Republic of China中国大陆U.S.A the United States ofAmerica 美国REV Revision 版本JIT Just In Time 零库存I/O Input/Output 输入/ 输出OK Ok 好NG Not Good 不行,不合格C=0 Critical=0 极严重不允许ESD Electry-static Discharge 静电排放5S 希腊语整理,整顿, 清扫,清洁,教养ATIN Attention 知会CC Carbon Copy 副本复印相关人员APP Approve 核准,认可,承认CHK Check 确认AM Ante Meridian 上午PM Post Meridian 下午CD Compact Disk 光碟CD-ROM Compact Disk Read-Only Memory 只读光碟FDD Floppy Disk Drive 软碟机HDD Hard Disk Drive 碟碟机REF Reference 仅供参考CONN Connector 连接器CAV Cavity 模穴CAD Computer Aid Design 计算机辅助设计ASS'Y Assembly 装配,组装MAT'S Material 材料IC Integrated Circuit 集成电路T/P True Position 真位度TYP Type 类型WDR Weekly DeliveryRequitement 周出货需求C?T Cycle Time 制程周期L/T Lead Time 前置时间( 生产前准备时间)S/T Standard Time 标准时间P/M Product Market 产品市场3CComputer,Commumcation,Consumer electronic's 消费性电子5WIHWhen,Where,Who,What,Why,Howto5MMan,Machine,Material,Method,Measurement4MIHMan,Materia,Money,Method,Time人力,物力, 财务,技术,时间(资源)SQA Strategy Quality Assurance策略品质保证DQA Desigh Quality Assurance设计品质保证MQA Manufacture QualityAssurance 制造品质保证SSQA Sales and service QualityAssurance 销售及服务品质保证LRR Lot Rejeet Rate 批退率BS Brain storming 脑力激荡EMI Electronic Magnetion Inspect高磁测试FMI Frequency Modulatim Inspect高频测试B/M Boar/Molding(flat cable)C/P Connector of PCA/P AssemblySPS Switching power supply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱)DVD Digital Vedio DiskVCD Vdeio Compact DiskLCD Liquid Crystal DisplayCAD Computer AID DesignCAM Computer AID ManufacturingCAE Computer AID Engineering ABIOS Achanced Basic in put/output system 先进的基本输入/输出系统CMOS Complemeruary Metoll Oxide Semiconductor 互补金属氧化物半导体PDA Personal Digital Assistant个人数字助理IC Integrated Circuit 集成电路ISA Industry StandardArchitecture 工业标准体制结构MCA Micro Channel Architecture微通道结构EISA Extended Industry StandardArchitecture 扩充的工业标准结构SIMM Single in-line memorymodule 单项导通汇流组件DIMM Dual in-line MemoryModule 双项导通汇流组件LED Light-Emitting Diode 发光二级管FMEA Failure Mode Effectivenes失效模式分析W/H Wire Harness 金属线绪束集组件F/C Flat Calle 排线PCB Printed Circuit Board 印刷电路板CAR Correction Action Report改善报告NG Not Good 不良WPR Weekly DeliveryRequirement 周出货要求PPM Parts Per Million 百万分之一TPM Total ProductionMaintenance 全面生产保养MRP Material RequiremcntPlanning 物料需计划OC Operation System 作业系统TBA To Be Design 待定,定缺D/C Drawing ChangeP/P Plans & ProceduneEMI Electrical-Music Industry 电子音乐工业RFI Read Frequency Input 读频输入MMC Maximum MaterialConditionMMS Maximum Material SizeLMC Least Material ConditionLMS Least Material Size模具技术用语各种模具常用成形方式accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形shellcasting 壳模铸造foam forming ? 泡成形sinterforging 烧结锻造forging roll 轧锻six sides forging六面锻造gravity casting 重力铸造slushmolding 凝塑成形hollow(blow) molding 中空(吹出) 成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding转送成形injection molding 射出成形warmforging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matchedmould thermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模landedplunger mold 有肩柱塞式模具burnishing die 挤光模landedpositive mold 有肩全压式模具button die镶入式圆形凹模loadingshoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold活动式模具clod hobbing 冷挤压制模louveringdie 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具extrusion die 挤出模palletizing die 叠层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die压紧模fishtail die 鱼尾形模具profile die轮廓模flash mold 溢料式模具progressivedie 顺序模gypsum mold 石膏铸模protablemold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模splitforging die 拼合锻模split mold 双并式模具spruelessmold 无注道残料模具squeezing die 挤压模stretchform die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 轭型模模具厂常用之标准零配件air vent vale 通气阀anchor pin锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流档板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 托架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁) cavity retainer plate 模穴托板center pin 中心梢clamping block 锁定块coil spring螺旋弹簧cold punched nut 冷冲螺母coolingspiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragmgate 盘形浇口die approach 模头料道die bed 型底die block 块形模体die body 铸模座die bush 合模衬套die button 冲模母模die clamper 夹模器die fastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 冲模板die set 冲压模座direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowel hole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drivebearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejectorleader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejectorvalve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板。

机械专业术语（英语）大全机械专业术语，中英文对照！阿基米德蜗杆Archimedes worm安全系数safety factor; factor of safety安全载荷safe load凹面、凹度concavity扳手wrench板簧flat leaf spring半圆键woodruff key变形deformation摆杆oscillating bar摆动从动件oscillating follower摆动从动件凸轮机构cam with oscillating follower 摆动导杆机构oscillating guide-bar mechanism摆线齿轮cycloidal gear摆线齿形cycloidal tooth profile摆线运动规律cycloidal motion摆线针轮cycloidal-pin wheel包角angle of contact保持架cage背对背安装back-to-back arrangement背锥back cone ；normal cone背锥角back angle背锥距back cone distance比例尺scale比热容specific heat capacity闭式链closed kinematic chain闭链机构closed chain mechanism臂部arm变频器frequency converters变频调速frequency control of motor speed变速speed change变速齿轮change gear ; change wheel变位齿轮modified gear变位系数modification coefficient标准齿轮standard gear标准直齿轮standard spur gear表面质量系数superficial mass factor表面传热系数surface coefficient of heat transfer表面粗糙度surface roughness并联式组合combination in parallel并联机构parallel mechanism并联组合机构parallel combined mechanism并行工程concurrent engineering并行设计concurred design, CD不平衡相位phase angle of unbalance不平衡imbalance (or unbalance)不平衡量amount of unbalance不完全齿轮机构intermittent gearing波发生器wave generator波数number of waves补偿compensation参数化设计parameterization design, PD残余应力residual stress操纵及控制装置operation control device槽轮Geneva wheel槽轮机构Geneva mechanism ；Maltese cross槽数Geneva numerate槽凸轮groove cam侧隙backlash差动轮系differential gear train差动螺旋机构differential screw mechanism差速器differential常用机构conventional mechanism; mechanism in common use 车床lathe承载量系数bearing capacity factor承载能力bearing capacity成对安装paired mounting尺寸系列dimension series齿槽tooth space齿槽宽spacewidth齿侧间隙backlash齿顶高addendum齿顶圆addendum circle齿根高dedendum齿根圆dedendum circle齿厚tooth thickness齿距circular pitch齿宽face width齿廓tooth profile齿廓曲线tooth curve齿轮gear齿轮变速箱speed-changing gear boxes齿轮齿条机构pinion and rack齿轮插刀pinion cutter; pinion-shaped shaper cutter 齿轮滚刀hob ,hobbing cutter齿轮机构gear齿轮轮坯blank齿轮传动系pinion unit齿轮联轴器gear coupling齿条传动rack gear齿数tooth number齿数比gear ratio齿条rack齿条插刀rack cutter; rack-shaped shaper cutter齿形链、无声链silent chain齿形系数form factor齿式棘轮机构tooth ratchet mechanism插齿机gear shaper重合点coincident points重合度contact ratio冲床punch传动比transmission ratio, speed ratio传动装置gearing; transmission gear传动系统driven system传动角transmission angle传动轴transmission shaft串联式组合combination in series串联式组合机构series combined mechanism串级调速cascade speed control创新innovation ; creation创新设计creation design垂直载荷、法向载荷normal load唇形橡胶密封lip rubber seal磁流体轴承magnetic fluid bearing从动带轮driven pulley从动件driven link, follower从动件平底宽度width of flat-face从动件停歇follower dwell从动件运动规律follower motion从动轮driven gear粗线bold line粗牙螺纹coarse thread大齿轮gear wheel打包机packer打滑slipping带传动belt driving带轮belt pulley带式制动器band brake单列轴承single row bearing单向推力轴承single-direction thrust bearing单万向联轴节single universal joint单位矢量unit vector当量齿轮equivalent spur gear; virtual gear当量齿数equivalent teeth number; virtual number of teeth当量摩擦系数equivalent coefficient of friction当量载荷equivalent load刀具cutter导数derivative倒角chamfer导热性conduction of heat导程lead导程角lead angle等加等减速运动规律parabolic motion; constant acceleration and deceleration motion 等速运动规律uniform motion; constant velocity motion等径凸轮conjugate yoke radial cam等宽凸轮constant-breadth cam等效构件equivalent link等效力equivalent force等效力矩equivalent moment of force等效量equivalent等效质量equivalent mass等效转动惯量equivalent moment of inertia等效动力学模型dynamically equivalent model底座chassis低副lower pair点划线chain dotted line（疲劳）点蚀pitting垫圈gasket垫片密封gasket seal碟形弹簧belleville spring顶隙bottom clearance定轴轮系ordinary gear train; gear train with fixed axes动力学dynamics动密封kinematical seal动能dynamic energy动力粘度dynamic viscosity动力润滑dynamic lubrication动平衡dynamic balance动平衡机dynamic balancing machine动态特性dynamic characteristics动态分析设计dynamic analysis design动压力dynamic reaction动载荷dynamic load端面transverse plane端面参数transverse parameters端面齿距transverse circular pitch端面齿廓transverse tooth profile端面重合度transverse contact ratio端面模数transverse module端面压力角transverse pressure angle锻造forge对称循环应力symmetry circulating stress对心滚子从动件radial (or in-line ) roller follower对心直动从动件radial (or in-line ) translating follower对心移动从动件radial reciprocating follower对心曲柄滑块机构in-line slider-crank (or crank-slider) mechanism 多列轴承multi-row bearing多楔带poly V-belt多项式运动规律polynomial motion多质量转子rotor with several masses惰轮idle gear额定寿命rating life额定载荷load ratingII 级杆组dyad发生线generating line发生面generating plane法面normal plane法面参数normal parameters法面齿距normal circular pitch法面模数normal module法面压力角normal pressure angle法向齿距normal pitch法向齿廓normal tooth profile法向直廓蜗杆straight sided normal worm法向力normal force反馈式组合feedback combining反向运动学inverse ( or backward) kinematics反转法kinematic inversion反正切Arctan范成法generating cutting仿形法form cutting方案设计、概念设计concept design, CD防振装置shockproof device飞轮flywheel飞轮矩moment of flywheel非标准齿轮nonstandard gear非接触式密封non-contact seal非周期性速度波动aperiodic speed fluctuation非圆齿轮non-circular gear粉末合金powder metallurgy分度线reference line; standard pitch line分度圆reference circle; standard (cutting) pitch circle 分度圆柱导程角lead angle at reference cylinder分度圆柱螺旋角helix angle at reference cylinder分母denominator分子numerator分度圆锥reference cone; standard pitch cone分析法analytical method封闭差动轮系planetary differential复合铰链compound hinge复合式组合compound combining复合轮系compound (or combined) gear train复合平带compound flat belt复合应力combined stress复式螺旋机构Compound screw mechanism复杂机构complex mechanism杆组Assur group干涉interference刚度系数stiffness coefficient刚轮rigid circular spline钢丝软轴wire soft shaft刚体导引机构body guidance mechanism刚性冲击rigid impulse (shock)刚性转子rigid rotor刚性轴承rigid bearing刚性联轴器rigid coupling高度系列height series高速带high speed belt高副higher pair格拉晓夫定理Grashoff`s law根切undercutting公称直径nominal diameter高度系列height series功work工况系数application factor工艺设计technological design工作循环图working cycle diagram工作机构operation mechanism工作载荷external loads工作空间working space工作应力working stress工作阻力effective resistance工作阻力矩effective resistance moment公法线common normal line公共约束general constraint公制齿轮metric gears功率power功能分析设计function analyses design共轭齿廓conjugate profiles共轭凸轮conjugate cam构件link鼓风机blower固定构件fixed link; frame固体润滑剂solid lubricant关节型操作器jointed manipulator惯性力inertia force惯性力矩moment of inertia ,shaking moment惯性力平衡balance of shaking force惯性力完全平衡full balance of shaking force惯性力部分平衡partial balance of shaking force 惯性主矩resultant moment of inertia惯性主失resultant vector of inertia冠轮crown gear广义机构generation mechanism广义坐标generalized coordinate轨迹生成path generation轨迹发生器path generator滚刀hob滚道raceway滚动体rolling element滚动轴承rolling bearing滚动轴承代号rolling bearing identification code 滚针needle roller滚针轴承needle roller bearing滚子roller滚子轴承roller bearing滚子半径radius of roller滚子从动件roller follower滚子链roller chain滚子链联轴器double roller chain coupling滚珠丝杆ball screw滚柱式单向超越离合器roller clutch过度切割undercutting函数发生器function generator函数生成function generation含油轴承oil bearing耗油量oil consumption耗油量系数oil consumption factor赫兹公式H. Hertz equation合成弯矩resultant bending moment合力resultant force合力矩resultant moment of force黑箱black box横坐标abscissa互换性齿轮interchangeable gears花键spline滑键、导键feather key滑动轴承sliding bearing滑动率sliding ratio滑块slider环面蜗杆toroid helicoids worm环形弹簧annular spring缓冲装置shocks; shock-absorber灰铸铁grey cast iron回程return回转体平衡balance of rotors混合轮系compound gear train积分integrate机电一体化系统设计mechanical-electrical integration system design 机构mechanism机构分析analysis of mechanism机构平衡balance of mechanism机构学mechanism机构运动设计kinematic design of mechanism机构运动简图kinematic sketch of mechanism机构综合synthesis of mechanism机构组成constitution of mechanism机架frame, fixed link机架变换kinematic inversion机器machine机器人robot机器人操作器manipulator机器人学robotics技术过程technique process技术经济评价technical and economic evaluation技术系统technique system机械machinery机械创新设计mechanical creation design, MCD机械系统设计mechanical system design, MSD机械动力分析dynamic analysis of machinery机械动力设计dynamic design of machinery机械动力学dynamics of machinery机械的现代设计modern machine design机械系统mechanical system机械利益mechanical advantage机械平衡balance of machinery机械手manipulator机械设计machine design; mechanical design机械特性mechanical behavior机械调速mechanical speed governors机械效率mechanical efficiency机械原理theory of machines and mechanisms机械运转不均匀系数coefficient of speed fluctuation机械无级变速mechanical stepless speed changes基础机构fundamental mechanism基本额定寿命basic rating life基于实例设计case-based design,CBD基圆base circle基圆半径radius of base circle基圆齿距base pitch基圆压力角pressure angle of base circle基圆柱base cylinder基圆锥base cone急回机构quick-return mechanism急回特性quick-return characteristics急回系数advance-to return-time ratio急回运动quick-return motion棘轮ratchet棘轮机构ratchet mechanism棘爪pawl极限位置extreme (or limiting) position极位夹角crank angle between extreme (or limiting) positions计算机辅助设计computer aided design, CAD计算机辅助制造computer aided manufacturing, CAM计算机集成制造系统computer integrated manufacturing system, CIMS 计算力矩factored moment; calculation moment计算弯矩calculated bending moment加权系数weighting efficient加速度acceleration加速度分析acceleration analysis加速度曲线acceleration diagram尖点pointing; cusp尖底从动件knife-edge follower间隙backlash间歇运动机构intermittent motion mechanism减速比reduction ratio减速齿轮、减速装置reduction gear减速器speed reducer减摩性anti-friction quality渐开螺旋面involute helicoid渐开线involute渐开线齿廓involute profile渐开线齿轮involute gear渐开线发生线generating line of involute渐开线方程involute equation渐开线函数involute function渐开线蜗杆involute worm渐开线压力角pressure angle of involute渐开线花键involute spline简谐运动simple harmonic motion键key键槽keyway交变应力repeated stress交变载荷repeated fluctuating load交叉带传动cross-belt drive交错轴斜齿轮crossed helical gears胶合scoring角加速度angular acceleration角速度angular velocity角速比angular velocity ratio角接触球轴承angular contact ball bearing角接触推力轴承angular contact thrust bearing角接触向心轴承angular contact radial bearing角接触轴承angular contact bearing铰链、枢纽hinge校正平面correcting plane接触应力contact stress接触式密封contact seal阶梯轴multi-diameter shaft结构structure结构设计structural design截面section节点pitch point节距circular pitch; pitch of teeth节线pitch line节圆pitch circle节圆齿厚thickness on pitch circle节圆直径pitch diameter节圆锥pitch cone节圆锥角pitch cone angle解析设计analytical design紧边tight-side紧固件fastener径节diametral pitch径向radial direction径向当量动载荷dynamic equivalent radial load径向当量静载荷static equivalent radial load径向基本额定动载荷basic dynamic radial load rating径向基本额定静载荷basic static radial load tating 径向接触轴承radial contact bearing径向平面radial plane径向游隙radial internal clearance径向载荷radial load径向载荷系数radial load factor径向间隙clearance静力static force静平衡static balance静载荷static load静密封static seal局部自由度passive degree of freedom矩阵matrix矩形螺纹square threaded form锯齿形螺纹buttress thread form矩形牙嵌式离合器square-jaw positive-contact clutch 绝对尺寸系数absolute dimensional factor绝对运动absolute motion绝对速度absolute velocity均衡装置load balancing mechanism抗压强度compression strength开口传动open-belt drive开式链open kinematic chain开链机构open chain mechanism可靠度degree of reliability可靠性reliability可靠性设计reliability design, RD空气弹簧air spring空间机构spatial mechanism空间连杆机构spatial linkage空间凸轮机构spatial cam空间运动副spatial kinematic pair空间运动链spatial kinematic chain空转idle宽度系列width series框图block diagram雷诺方程Reynolds‘s equation离心力centrifugal force离心应力centrifugal stress离合器clutch离心密封centrifugal seal理论廓线pitch curve理论啮合线theoretical line of action隶属度membership力force力多边形force polygon力封闭型凸轮机构force-drive (or force-closed) cam mechanism 力矩moment力平衡equilibrium力偶couple力偶矩moment of couple连杆connecting rod, coupler连杆机构linkage连杆曲线coupler-curve连心线line of centers链chain链传动装置chain gearing链轮sprocket ; sprocket-wheel ; sprocket gear ; chain wheel 联组V 带tight-up V belt联轴器coupling ; shaft coupling两维凸轮two-dimensional cam临界转速critical speed六杆机构six-bar linkage龙门刨床double Haas planer轮坯blank轮系gear train螺杆screw螺距thread pitch螺母screw nut螺旋锥齿轮helical bevel gear螺钉screws螺栓bolts螺纹导程lead螺纹效率screw efficiency螺旋传动power screw螺旋密封spiral seal螺纹thread (of a screw)螺旋副helical pair螺旋机构screw mechanism螺旋角helix angle螺旋线helix ,helical line绿色设计green design ; design for environment马耳他机构Geneva wheel ; Geneva gear马耳他十字Maltese cross脉动无级变速pulsating stepless speed changes脉动循环应力fluctuating circulating stress脉动载荷fluctuating load铆钉rivet迷宫密封labyrinth seal密封seal密封带seal belt密封胶seal gum密封元件potted component密封装置sealing arrangement面对面安装face-to-face arrangement面向产品生命周期设计design for product`s life cycle, DPLC 名义应力、公称应力nominal stress模块化设计modular design, MD模块式传动系统modular system模幅箱morphology box模糊集fuzzy set模糊评价fuzzy evaluation模数module摩擦friction摩擦角friction angle摩擦力friction force摩擦学设计tribology design, TD摩擦阻力frictional resistance摩擦力矩friction moment摩擦系数coefficient of friction摩擦圆friction circle磨损abrasion ;wear; scratching末端执行器end-effector目标函数objective function耐腐蚀性corrosion resistance耐磨性wear resistance挠性机构mechanism with flexible elements挠性转子flexible rotor内齿轮internal gear内齿圈ring gear内力internal force内圈inner ring能量energy能量指示图viscosity逆时针counterclockwise (or anticlockwise)啮出engaging-out啮合engagement, mesh, gearing啮合点contact points啮合角working pressure angle啮合线line of action啮合线长度length of line of action啮入engaging-in牛头刨床shaper凝固点freezing point; solidifying point扭转应力torsion stress扭矩moment of torque扭簧helical torsion spring诺模图NomogramO 形密封圈密封O ring seal盘形凸轮disk cam盘形转子disk-like rotor抛物线运动parabolic motion疲劳极限fatigue limit疲劳强度fatigue strength偏置式offset偏( 心) 距offset distance偏心率eccentricity ratio偏心质量eccentric mass偏距圆offset circle偏心盘eccentric偏置滚子从动件offset roller follower偏置尖底从动件offset knife-edge follower偏置曲柄滑块机构offset slider-crank mechanism 拼接matching评价与决策evaluation and decision频率frequency平带flat belt平带传动flat belt driving平底从动件flat-face follower平底宽度face width平分线bisector平均应力average stress平均中径mean screw diameter平均速度average velocity平衡balance平衡机balancing machine平衡品质balancing quality平衡平面correcting plane平衡质量balancing mass平衡重counterweight平衡转速balancing speed平面副planar pair, flat pair平面机构planar mechanism平面运动副planar kinematic pair平面连杆机构planar linkage平面凸轮planar cam平面凸轮机构planar cam mechanism平面轴斜齿轮parallel helical gears普通平键parallel key其他常用机构other mechanism in common use起动阶段starting period启动力矩starting torque气动机构pneumatic mechanism奇异位置singular position起始啮合点initial contact , beginning of contact气体轴承gas bearing千斤顶jack嵌入键sunk key强迫振动forced vibration切齿深度depth of cut曲柄crank曲柄存在条件Grashoff`s law曲柄导杆机构crank shaper (guide-bar) mechanism曲柄滑块机构slider-crank (or crank-slider) mechanism 曲柄摇杆机构crank-rocker mechanism曲齿锥齿轮spiral bevel gear曲率curvature曲率半径radius of curvature曲面从动件curved-shoe follower曲线拼接curve matching曲线运动curvilinear motion曲轴crank shaft驱动力driving force驱动力矩driving moment (torque)全齿高whole depth权重集weight sets球ball球面滚子convex roller球轴承ball bearing球面副spheric pair球面渐开线spherical involute球面运动spherical motion球销副sphere-pin pair球坐标操作器polar coordinate manipulator燃点spontaneous ignition热平衡heat balance; thermal equilibrium人字齿轮herringbone gear冗余自由度redundant degree of freedom柔轮flexspline柔性冲击flexible impulse; soft shock柔性制造系统flexible manufacturing system; FMS柔性自动化flexible automation润滑油膜lubricant film润滑装置lubrication device润滑lubrication润滑剂lubricant三角形花键serration spline三角形螺纹V thread screw三维凸轮three-dimensional cam三心定理Kennedy`s theorem砂轮越程槽grinding wheel groove砂漏hour-glass少齿差行星传动planetary drive with small teeth difference 设计方法学design methodology设计变量design variable设计约束design constraints深沟球轴承deep groove ball bearing生产阻力productive resistance升程rise升距lift实际廓线cam profile十字滑块联轴器double slider coupling; Oldham‘s co upling 矢量vector输出功output work输出构件output link输出机构output mechanism输出力矩output torque输出轴output shaft输入构件input link数学模型mathematic model实际啮合线actual line of action双滑块机构double-slider mechanism, ellipsograph双曲柄机构double crank mechanism双曲面齿轮hyperboloid gear双头螺柱studs双万向联轴节constant-velocity (or double) universal joint 双摇杆机构double rocker mechanism双转块机构Oldham coupling双列轴承double row bearing双向推力轴承double-direction thrust bearing松边slack-side顺时针clockwise瞬心instantaneous center死点dead point四杆机构four-bar linkage速度velocity速度不均匀( 波动) 系数coefficient of speed fluctuation 速度波动speed fluctuation速度曲线velocity diagram速度瞬心instantaneous center of velocity塔轮step pulley踏板pedal台钳、虎钳vice太阳轮sun gear弹性滑动elasticity sliding motion弹性联轴器elastic coupling ; flexible coupling弹性套柱销联轴器rubber-cushioned sleeve bearing coupling 套筒sleeve梯形螺纹acme thread form特殊运动链special kinematic chain特性characteristics替代机构equivalent mechanism调节modulation, regulation调心滚子轴承self-aligning roller bearing调心球轴承self-aligning ball bearing调心轴承self-aligning bearing调速speed governing调速电动机adjustable speed motors调速系统speed control system调压调速variable voltage control调速器regulator, governor铁磁流体密封ferrofluid seal停车阶段stopping phase停歇dwell同步带synchronous belt同步带传动synchronous belt drive凸的，凸面体convex凸轮cam凸轮倒置机构inverse cam mechanism凸轮机构cam , cam mechanism凸轮廓线cam profile凸轮廓线绘制layout of cam profile凸轮理论廓线pitch curve凸缘联轴器flange coupling图册、图谱atlas图解法graphical method推程rise推力球轴承thrust ball bearing推力轴承thrust bearing退刀槽tool withdrawal groove退火anneal陀螺仪gyroscopeV 带V belt外力external force外圈outer ring外形尺寸boundary dimension万向联轴器Hooks coupling ; universal coupling 外齿轮external gear弯曲应力beading stress弯矩bending moment腕部wrist往复移动reciprocating motion往复式密封reciprocating seal网上设计on-net design, OND微动螺旋机构differential screw mechanism位移displacement位移曲线displacement diagram位姿pose , position and orientation稳定运转阶段steady motion period稳健设计robust design蜗杆worm蜗杆传动机构worm gearing蜗杆头数number of threads蜗杆直径系数diametral quotient蜗杆蜗轮机构worm and worm gear蜗杆形凸轮步进机构worm cam interval mechanism蜗杆旋向hands of worm蜗轮worm gear涡圈形盘簧power spring无级变速装置stepless speed changes devices无穷大infinite系杆crank arm, planet carrier现场平衡field balancing向心轴承radial bearing向心力centrifugal force相对速度relative velocity相对运动relative motion相对间隙relative gap象限quadrant橡皮泥plasticine细牙螺纹fine threads销pin消耗consumption小齿轮pinion小径minor diameter橡胶弹簧balata spring修正梯形加速度运动规律modified trapezoidal acceleration motion 修正正弦加速度运动规律modified sine acceleration motion斜齿圆柱齿轮helical gear斜键、钩头楔键taper key泄漏leakage谐波齿轮harmonic gear谐波传动harmonic driving谐波发生器harmonic generator斜齿轮的当量直齿轮equivalent spur gear of the helical gear心轴spindle行程速度变化系数coefficient of travel speed variation行程速比系数advance-to return-time ratio行星齿轮装置planetary transmission行星轮planet gear行星轮变速装置planetary speed changing devices行星轮系planetary gear train形封闭凸轮机构positive-drive (or form-closed) cam mechanism 虚拟现实virtual reality虚拟现实技术virtual reality technology, VRT虚拟现实设计virtual reality design, VRD虚约束redundant (or passive) constraint许用不平衡量allowable amount of unbalance许用压力角allowable pressure angle许用应力allowable stress; permissible stress悬臂结构cantilever structure悬臂梁cantilever beam循环功率流circulating power load旋转力矩running torque旋转式密封rotating seal旋转运动rotary motion选型type selection压力pressure压力中心center of pressure压缩机compressor压应力compressive stress压力角pressure angle牙嵌式联轴器jaw (teeth) positive-contact coupling雅可比矩阵Jacobi matrix摇杆rocker液力传动hydrodynamic drive液力耦合器hydraulic couplers液体弹簧liquid spring液压无级变速hydraulic stepless speed changes液压机构hydraulic mechanism一般化运动链generalized kinematic chain移动从动件reciprocating follower移动副prismatic pair, sliding pair移动关节prismatic joint移动凸轮wedge cam盈亏功increment or decrement work应力幅stress amplitude应力集中stress concentration应力集中系数factor of stress concentration应力图stress diagram应力—应变图stress-strain diagram优化设计optimal design油杯oil bottle油壶oil can油沟密封oily ditch seal有害阻力useless resistance有益阻力useful resistance有效拉力effective tension有效圆周力effective circle force有害阻力detrimental resistance余弦加速度运动cosine acceleration (or simple harmonic) motion 预紧力preload原动机primer mover圆带round belt圆带传动round belt drive圆弧齿厚circular thickness圆弧圆柱蜗杆hollow flank worm圆角半径fillet radius圆盘摩擦离合器disc friction clutch圆盘制动器disc brake原动机prime mover原始机构original mechanism圆形齿轮circular gear圆柱滚子cylindrical roller圆柱滚子轴承cylindrical roller bearing圆柱副cylindric pair圆柱式凸轮步进运动机构barrel (cylindric) cam圆柱螺旋拉伸弹簧cylindroid helical-coil extension spring圆柱螺旋扭转弹簧cylindroid helical-coil torsion spring圆柱螺旋压缩弹簧cylindroid helical-coil compression spring圆柱凸轮cylindrical cam圆柱蜗杆cylindrical worm圆柱坐标操作器cylindrical coordinate manipulator圆锥螺旋扭转弹簧conoid helical-coil compression spring圆锥滚子tapered roller圆锥滚子轴承tapered roller bearing圆锥齿轮机构bevel gears圆锥角cone angle原动件driving link约束constraint约束条件constraint condition约束反力constraining force跃度jerk跃度曲线jerk diagram运动倒置kinematic inversion运动方案设计kinematic precept design运动分析kinematic analysis运动副kinematic pair运动构件moving link运动简图kinematic sketch运动链kinematic chain运动失真undercutting运动设计kinematic design运动周期cycle of motion运动综合kinematic synthesis运转不均匀系数coefficient of velocity fluctuation 运动粘度kenematic viscosity载荷load载荷—变形曲线load—deformation curve载荷—变形图load—deformation diagram窄V 带narrow V belt毡圈密封felt ring seal展成法generating张紧力tension张紧轮tension pulley振动vibration振动力矩shaking couple振动频率frequency of vibration振幅amplitude of vibration正切机构tangent mechanism正向运动学direct (forward) kinematics正弦机构sine generator, scotch yoke织布机loom正应力、法向应力normal stress制动器brake直齿圆柱齿轮spur gear直齿锥齿轮straight bevel gear直角三角形right triangle直角坐标操作器Cartesian coordinate manipulator 直径系数diametral quotient直径系列diameter series直廓环面蜗杆hindley worm直线运动linear motion直轴straight shaft质量mass质心center of mass执行构件executive link; working link质径积mass-radius product智能化设计intelligent design, ID中间平面mid-plane中心距center distance中心距变动center distance change中心轮central gear中径mean diameter终止啮合点final contact, end of contact周节pitch周期性速度波动periodic speed fluctuation周转轮系epicyclic gear train肘形机构toggle mechanism轴shaft轴承盖bearing cup轴承合金bearing alloy轴承座bearing block轴承高度bearing height轴承宽度bearing width轴承内径bearing bore diameter轴承寿命bearing life轴承套圈bearing ring轴承外径bearing outside diameter轴颈journal轴瓦、轴承衬bearing bush轴端挡圈shaft end ring轴环shaft collar轴肩shaft shoulder轴角shaft angle轴向axial direction轴向齿廓axial tooth profile轴向当量动载荷dynamic equivalent axial load轴向当量静载荷static equivalent axial load轴向基本额定动载荷basic dynamic axial load rating 轴向基本额定静载荷basic static axial load rating轴向接触轴承axial contact bearing轴向平面axial plane轴向游隙axial internal clearance轴向载荷axial load轴向载荷系数axial load factor轴向分力axial thrust load主动件driving link主动齿轮driving gear主动带轮driving pulley转动导杆机构whitworth mechanism转动副revolute (turning) pair转速swiveling speed ; rotating speed转动关节revolute joint转轴revolving shaft转子rotor转子平衡balance of rotor装配条件assembly condition锥齿轮bevel gear锥顶common apex of cone锥距cone distance锥轮bevel pulley; bevel wheel锥齿轮的当量直齿轮equivalent spur gear of the bevel gear锥面包络圆柱蜗杆milled helicoids worm准双曲面齿轮hypoid gear子程序subroutine子机构sub-mechanism自动化automation自锁self-locking自锁条件condition of self-locking自由度degree of freedom, mobility总重合度total contact ratio总反力resultant force总效率combined efficiency; overall efficiency组成原理theory of constitution组合齿形composite tooth form组合安装stack mounting组合机构combined mechanism阻抗力resistance最大盈亏功maximum difference work between plus and minus work 纵向重合度overlap contact ratio纵坐标ordinate组合机构combined mechanism最少齿数minimum teeth number最小向径minimum radius作用力applied force坐标系coordinate frame机械专利翻译词汇三千个Assembly line 组装线Layout 布置图Conveyer 流水线物料板Rivet table 拉钉机Rivet gun 拉钉枪Screw driver 起子Electric screw driver 电动起子Pneumatic screw driver 气动起子worktable 工作桌OOBA 开箱检查fit together 组装在一起fasten 锁紧(螺丝)fixture 夹具(治具)pallet 栈板barcode 条码barcode scanner 条码扫描器fuse together 熔合fuse machine 热熔机repair 修理operator 作业员QC 品管supervisor 课长ME 制造工程师cosmetic inspect 外观检查inner parts inspect 内部检查thumb screw 大头螺丝lbs. Inch 镑、英寸EMI gasket 导电条front plate 前板rear plate 后板chassis 基座bezel panel 面板power button 电源按键reset button 重置键Hi-pot test of SPS 高源高压测试V oltage switch of SPS 电源电压接拉键sheet metal parts 冲件plastic parts 塑胶件SOP 制造作业程序material check list 物料检查表work cell 工作间trolley 台车carton 纸箱sub-line 支线left fork 叉车personnel resource department 人力资源部production department 生产部门planning department 企划部QC Section 品管科stamping factory 冲压厂painting factory 烤漆厂molding factory 成型厂common equipment 常用设备uncoiler and straightener 整平机punching machine 冲床robot 机械手hydraulic machine 油压机lathe 车床planer 刨床miller 铣床grinder 磨床driller 钻床linear cutting 线切割electrical sparkle 电火花welder 电焊机staker=reviting machine 铆合机position 职务president 董事长general manager 总经理special assistant manager 特别助理factory director 厂长department director 部长deputy manager | =vice manager 副经理section supervisor 课长deputy section supervisor =vice section superisor 副课长group leader/supervisor 组长line supervisor 线长assistant manager 助理to move, to carry, to handle 搬运be put in storage 入库pack packing 包装to apply oil 擦油to file burr 锉毛刺final inspection 终检to connect material 接料to reverse material 翻料wet station 沾湿台Tiana 天那水cleaning cloth 抹布to load material 上料to unload material 卸料to return material/stock to 退料scraped |'skræpid| 报废scrape 刮;削deficient purchase 来料不良manufacture procedure 制造过程deficient manufacturing procedur 制造过程不良oxidation 氧化scratch 刮伤dents 压痕defective upsiding down 抽芽不良defective to staking 铆合不良embedded lump 镶块feeding is not in place 送料不到位stamping-missing 漏冲production capacity 生产力education and training 教育与训练proposal improvement 提案改善spare parts=buffer 备件forklift 叉车trailer=long vehicle 拖板车compound die 合模die locker 锁模器pressure plate=plate pinch 压板bolt 螺栓name of a department 部门名称administration/general affairs dept 总务部automatic screwdriver 电动启子thickness gauge 厚薄规gauge(or jig) 治具power wire 电源线buzzle 蜂鸣器defective product label 不良标签identifying sheet list 标示单screwdriver holder 起子插座pedal 踩踏板stopper 阻挡器。

机械专业术语中英文对照机械专业术语组装、冲压、喷漆等专业词汇 Assembly line 组装线 Layout 布置图 Conveyer 流水线物料板 Rivet table 拉钉机Rivet gun 拉钉枪 Screw driver 起子 Electric screw driver 电动起子 Pneumatic screw driver 气动起子 worktable 工作桌OOBA 开箱检查 fit together 组装在一起 fasten 锁紧(螺丝) fixture 夹具(治具) pallet 栈板 barcode 条码 barcode scanner 条码扫描器 fuse together 熔合 fuse machine 热熔机 repair 修理 operator 作业员 QC 品管 supervisor 课长 ME 制造工程师 MT 制造生技 cosmetic inspect 外观检查 inner parts inspect 内部检查 thumb screw 大头螺丝 lbs. inch 镑、英寸 EMI gasket 导电条 front plate 前板 rear plate 后板 chassis 基座 bezel panel 面板 power button 电源按键 reset button 重置键 Hi-pot test of SPS 高源高压测试 Voltage switch of SPS 电源电压接拉键 sheet metal parts 冲件 plastic parts 塑胶件 SOP 制造作业程序 material check list 物料检查表 work cell 工作间trolley 台车 carton 纸箱 sub-line 支线 left fork 叉车personnel resource department 人力资源部 production department 生产部门 planning department 企划部 QC Section 品管科 stamping factory 冲压厂 painting factory 烤漆厂molding factory 成型厂 mon equipment 常用设备 uncoiler and straightener 整平机 punching machine 冲床 robot 机械手hydraulic machine 油压机 lathe 车床 planer |"plein|刨床 miller 铣床 grinder 磨床 driller 钻床 linear cutting 线切割 electrical sparkle 电火花 welder 电焊机staker=reviting machine 铆合机 position 职务 president 董事长 general manager 总经理 special assistant manager 特助factory director 厂长 department director 部长 deputy manager=vice manager 副理 section supervisor 课长 deputy section supervisor 副课长 vice section superisor 副课长group leader/supervisor 组长 line supervisor 线长 assistant manager 助理 to move, to carry, to handle 搬运 be put in storage 入库 pack packing 包装 to apply oil 擦油 to file burr 锉毛刺 final inspection 终检 to connect material 接料to reverse material 翻料 wet station 沾湿台 Tiana 天那水cleaning cloth 抹布 to load material 上料 to unload material 卸料 to return material/stock to 退料 scraped |"skræpid|报废 scrape ..v.刮;削 deficient purchase 来料不良 manufacture procedure 制程 deficient manufacturing procedure制程不良 oxidation |" ksi"dein|氧化scratch 刮伤 dents 压痕 defective upsiding down 抽芽不良defective to staking 铆合不良 embedded lump 镶块 feeding is not in place 送料不到位 stamping-missing 漏冲 production capacity 生产力 education and training 教育与训练 proposal improvement 提案改善 spare parts=buffer 备件 forklift 叉车trailer=long vehicle 拖板车 pound die 合模 die locker 锁模器 pressure plate=plate pinch 压板 bolt 螺栓 name of a department 部门名称 administration/general affairs dept总务部 automatic screwdriver 电动启子 thickness gauge 厚薄规gauge(or jig)治具 power wire 电源线 buzzle 蜂鸣器 defectiveproduct label 不良标签 identifying sheet list 标示单screwdriver holder 起子插座 pedal 踩踏板 stopper 阻挡器flow board 流水板 hydraulic handjack 油压板车 forklift 叉车pallet 栈板 glove(s)手套 glove(s) with exposed fingers 割手套 thumb 大拇指 forefinger 食指 midfinger 中指 ring finger 无名指 little finger 小指 band-aid 创可贴 iudustrial alcohol 工业酒精 alcohol container 沾湿台 head of screwdriver 起子头 sweeper 扫把 mop 拖把 vaum cleaner 吸尘器 rag 抹布garbage container 灰箕 garbage can 垃圾箱 garbage bag 垃圾袋 chain 链条 jack 升降机 production line 流水线 chain 链条槽 magizer 加磁器 lamp holder 灯架 to mop the floor 拖地 to clean the floor 扫地 to clean a table 擦桌子 air pipe 气管packaging tool 打包机 packaging 打包 missing part 漏件wrong part 错件 excessive defects 过多的缺陷 critical defect 极严重缺陷 major defect 主要缺陷 minor defect 次要缺陷 not up to standard 不合规格 dimension/size is a little bigger 尺寸偏大(小) cosmetic defect 外观不良 slipped screwhead/slippery screw head 螺丝滑头 slippedscrewhead/shippery screw thread 滑手 speckle 斑点mildewed=moldy=mouldy 发霉 rust 生锈 deformation 变形burr(金属)flash(塑件)毛边 poor staking 铆合不良 excesssive gap 间隙过大 grease/oil stains 油污 inclusion 杂质 painting peel off 脏污 shrinking/shrinkage 缩水 mixed color 杂色scratch 划伤 poor processing 制程不良 poor ining part 事件不良 fold of pakaging belt 打包带折皱 painting make-up 补漆discoloration 羿色 water spots 水渍 polishing/surface processing外表处理 exposed metal/bare metal 金属裸露 lack of painting 烤漆不到位 safety 平安 quality 品质 delivery deadline 交货期 cost 本钱 engineering 工程 die repair 模修enterprise plan = enterprise expansion projects 企划 QC 品管 die worker 模工 production, to produce 生产 equipment 设备 to start a press 开机 stop/switch off a press 关机classification regulation 整顿 cleanness 清扫 conservation 清洁 culture 教养 qualified products, up-to-grade products 良品 defective products, not up-to-grade products 不良品waste 废料 board 看板 feeder 送料机 sliding rack 滑料架defective product box 不良品箱 die change 换模 to fix a die 装模 to take apart a die 拆模 to repair a die 修模 packing material 包材 basket 蝴蝶竺 plastic basket 胶筐 isolating plate baffle plate; barricade 隔板 carton box 纸箱 to pull and stretch 拉深 to put material in place, to cut material, to input 落料 to impose lines 压线 to press, pressing 压缩character die 字模 to feed, feeding 送料 transportation 运输 (be)qualfied, up to grade 合格 not up to grade, not qualified 不合格 material change, stock change 材料变更feature change 特性变更 evaluation 评估 prepare for, make preparations for 准备 parameters 参数 rotating speed, revolution 转速 manufacture management 制造管理 abnormal handling 异常处理 production unit 生产单位 lots ofproduction 生产批量 steel plate 钢板 roll material 卷料manufacture procedure 制程 operation procedure 作业流程 to revise, modify 修订 to switch over to, switch---to throw--over switching over 切换 engineering, project difficulty 工程瓶颈 stage die 工程模 automation 自动化 to stake, staking, reviting 铆合 add lubricating oil 加润滑油 shut die 架模shut height of a die 架模高度 analog-mode device 类模器 die lifter 举模器 argon welding 氩焊 vocabulary for stamping 冲压常词汇 stamping, press 冲压 punch press, dieing out press 冲床 uncoiler & strainghtener 整平机 feeder 送料机 rack, shelf, stack 料架 cylinder 油缸 robot 机械手 taker 取料机conveyer belt 输送带 transmission rack 输送架 top stop 上死点 bottom stop 下死点 one stroke 一行程 inch 寸动 to continue, cont.连动 to grip(material)吸料 location lump, locating piece, block stop 定位块 reset 复位 smoothly 顺利dent 压痕 scratch 刮伤 deformation 变形 filings 铁削 todraw holes 抽孔 inquiry, search for 查寻 to stock, storage, in stock 库存 receive 领取 approval examine and verify 审核processing, to process 加工 delivery, to deliver 交货 to return delivenry to. to send delinery back to retrn ofgoods 退货 registration 登记 registration card 登记卡 to control 管制 to put forward and hand in 提报 safe stock 平安库存 aeptance = receive 验收 to notice 通知 application form for purchase 请购单 consume, consumption 消耗 to fillin 填写 abrasion 磨损 reverse angle = chamfer 倒角character die 字模 to collect, to gather 收集 failure, trouble 故障 statistics 统计 demand and supply 需求 career card 履历卡 to take apart a die 卸下模具 to load a die 装上模具 to tight a bolt 拧紧螺栓 to looser a bolt 拧松螺栓 to move away a die plate 移走模板 easily damaged parts 易损件standard parts 标准件 breaking.(be)broken,(be)cracked 断裂to lubricate 润滑 mon vocabulary for die engineering 模具工程常用词汇 die 模具 figure file, chart file 图档 cutting die, blanking die 冲裁模 progressive die, follow (-on)die 连续模 pound die 复合模 punched hole 冲孔 panel board 镶块to cutedges=side cut=side scrap 切边 to bending 折弯 to pull, to stretch 拉伸 Line streching, line pulling 线拉伸engraving, to engrave 刻印 upsiding down edges 翻边 to stake 铆合 designing, to design 设计 design modification 设计变化 die block 模块 folded block 折弯块 sliding block 滑块 location pin 定位销 lifting pin 顶料销 die plate, front board 模板 padding block 垫块 stepping bar 垫条 upper die base 上模座 lower die base 下模座 upper supporting blank 上承板 upper padding plate blank 上垫板 spare dies 模具备品spring 弹簧 bolt 螺栓 document folder 文件夹 file folder 资料夹 to put file in order 资料 spare tools location 手工备品仓 first count 初盘人 first check 初盘复棹人 second count 复盘人 second check 复盘复核人 equipment 设备 waste materials 废料 work in progress product 在制品 casing = containerazation 装箱 quantity of physical invetory secondcount 复盘点数量 quantity of customs count 会计师盘,点数量the first page 第一联 filed by aounting department for reference 会计部存查 end-user/using unit(department) 使用单位 summary of year-end physical inventory bills 年终盘点截止单据汇总表 bill name 单据名称 This sheet and physical inventory list will be sent to aounting department together (Those of NHK will be sent to financial department) 本表请与盘点清册一起送会计部－(NHK 厂区送财会部) Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO. 空白与作废单号 plate 电镀 mold 成型 material for engineering mold testing 工程试模材料 not included in physical inventory不列入盘点 sample 样品 ining material to be inspected进货待验 description 品名steel/rolled steel 钢材 material statistics sheet 物料统计明细表 meeting minutes 会议记录 meeting type 会别distribution department 分发单位 location 地点 chairman 主席 present members 出席人员 subject 主题 conclusion 结论decision items 决议事项 responsible department 负责单位pre-fixed finishing date预定完成日 approved by / checked by / prepared by 核准/审核/承办 PCE assembly production schedule sheet PCE 组装厂生产排配表 model 机锺 work order 工令 revision 版次 remark 备注 production control confirmation 生产确认checked by 初审 approved by 核准 department 部门 stock age analysis sheet 库存货龄分析表 on-hand inventory 现有库存available material 良品可使用 obsolete material 良品已呆滞to be inspected or reworked 待验或重工 total 合计 cause description 原因说明 part number/ P/N 料号 type 形态item/group/class 类别 quality 品质 prepared by 制表 notes 说明 year-end physical inventory difference analysis sheet 年终盘点差异分析表 physical inventory 盘点数量 physical count quantity 帐面数量 difference quantity 差异量 cause analysis 原因分析 raw materials 原料 materials 物料finished product 成品 semi-finished product 半成品 packing materials 包材 good product/aepted goods/ aepted parts/good parts 良品 defective product/non-good parts 不良品 disposed goods 处理品 warehouse/hub 仓库 on way location 在途仓oversea location 海外仓 spare parts physical inventory list 备品盘点清单 spare molds location 模具备品仓 skid/pallet 栈板 tox machine 自铆机 wire EDM 线割 EDM 放电机 coil stock 卷料 sheet stock 片料 tolerance 工差 score=groove 压线 cam block 滑块 pilot 导正筒 trim 剪外边 pierce 剪内边 drag form 压锻差 pocket for the punch head 挂钩槽 slug hole 废料孔feature die 公母模 expansion dwg 展开图 radius 半径shim(wedge)楔子 torch-flame cut 火焰切割 set screw 止付螺丝form block 折刀 stop pin 定位销 round pierce punch=die button 圆冲子 shape punch=die insert 异形子 stock locater block 定位块 under cut=scrap chopper 清角 active plate 活动板 baffle plate 挡块 cover plate 盖板 male die 公模 female die 母模 groove punch 压线冲子 air-cushion eject-rod 气垫顶杆 spring-box eject-plate 弹簧箱顶板 bushing block 衬套insert 入块 club car 高尔夫球车 capability 能力 parameter 参数 factor 系数 phosphate 皮膜化成 viscosity 涂料粘度alkalidipping 脱脂 main manifold 主集流脉 bezel 斜视规blanking 穿落模 dejecting 顶固模 demagization 去磁;消磁high-speed transmission 高速传递 heat dissipation 热传 rack 上料 degrease 脱脂 rinse 水洗 alkaline etch 龄咬 desmut 剥黑膜 D.I. rinse 纯水次 Chromate 铬酸处理 Anodize 阳性处理seal 封孔 revision 版次 part number/P/N 料号 good products 良品 scraped products 报放心品 defective products 不良品finished products 成品 disposed products 处理品 barcode 条码 flow chart 流程表单 assembly 组装 stamping 冲压 molding 成型 spare parts=buffer 备品 coordinate 座标 dismantle the die 折模 auxiliary fuction 辅助功能 poly-line 多义线 heater band 加热片 thermocouple 热电偶 sand blasting 喷沙 grit 砂砾 derusting machine 除锈机 degate 打浇口 dryer 烘干机induction 感应 induction light 感应光response=reaction=interaction 感应 ram 连杆 edge finder 巡边器 concave 凸 convex 凹 short 射料缺乏 nick 缺口 speck 瑕?? shine 亮班 splay 银纹 gas mark 焦痕 delamination 起鳞cold slug 冷块 blush 导色 gouge 沟槽;凿槽 satin texture 段面咬花 witness line 证示线 patent 专利 grit 沙砾granule=peuet=grain 细粒 grit maker 抽粒机 cushion 缓冲magnalium 镁铝合金 magnesium 镁金 metal plate 钣金 lathe 车mill 锉plane 刨 grind 磨 drill 铝 boring 镗 blinster 气泡 fillet 镶;嵌边 through-hole form 通孔形式 voller pin formality 滚针形式 cam driver 铡楔 shank 摸柄 crank shaft 曲柄轴augular offset 角度偏差 velocity 速度 production tempo 生产进度现状 torque 扭矩 spline=the multiple keys 花键quenching 淬火 tempering 回火 annealing 退火 carbonization 碳化 alloy 合金 tungsten high speed steel 钨高速的 moly high speed steel 钼高速的 organic solvent 有机溶剂 bracket 小磁导 liaison 联络单 volatile 挥发性 resistance 电阻 ion 离子 titrator 滴定仪 beacon 警示灯 coolant 冷却液 crusher 破碎机模具工程类 plain die 简易模 pierce die 冲孔模forming die 成型模 progressive die 连续模 gang dies 复合模shearing die 剪边模 riveting die 铆合模 pierce 冲孔 forming 成型(抽凸,冲凸) draw hole 抽孔 bending 折弯 trim 切边emboss 凸点 dome 凸圆 semi-shearing 半剪 stamp mark 冲记号deburr or coin 压毛边 punch riveting 冲压铆合 side stretch 侧冲压平 reel stretch 卷圆压平 groove 压线 blanking 下料stamp letter 冲字(料号) shearing 剪断 tick-mark nearside 正面压印 tick-mark farside 反面压印冲压名称类 extension dwg 展开图 procedure dwg 工程图 die structure dwg 模具结构图material 材质 material thickness 料片厚度 factor 系数upward 向上 downward 向下 press specification 冲床规格 die height range 适用模高 die height 闭模高度 burr 毛边 gap 间隙 weight 重量 total wt.总重量 punch wt.上模重量五金零件类inner guiding post 内导柱 inner hexagon screw 内六角螺钉dowel pin 固定销 coil spring 弹簧 lifter pin 顶料销 eq-height sleeves=spool 等高套筒 pin 销 lifter guide pin 浮升导料销 guide pin 导正销 wire spring 圆线弹簧 outer guiding post 外导柱 stop screw 止付螺丝 located pin 定位销 outer bush 外导套模板类 top plate 上托板（顶板） top block 上垫脚 punch set 上模座 punch pad 上垫板 punch holder 上夹板stripper pad 脱料背板 up stripper 上脱料板 male die 公模(凸模) feature die 公母模 female die 母模(凹模) upper plate 上模板 lower plate 下模板 die pad 下垫板 die holder 下夹板die set 下模座 bottom block 下垫脚 bottom plate 下托板(底板) stripping plate 内外打(脱料板) outer stripper 外脱料板inner stripper 内脱料板 lower stripper 下脱料板零件类punch 冲头 insert 入块(嵌入件) deburring punch 压毛边冲子groove punch 压线冲子 stamped punch 字模冲子 round punch 圆冲子 special shape punch 异形冲子 bending block 折刀 roller 滚轴 baffle plate 挡块 located block 定位块 supportingblock for location 定位支承块 air cushion plate 气垫板 air-cushion eject-rod 气垫顶杆 trimming punch 切边冲子stiffening rib punch = stinger 加强筋冲子 ribbon punch 压筋冲子 reel-stretch punch 卷圆压平冲子 guide plate 定位板sliding block 滑块 sliding dowel block 滑块固定块 active plate 活动板 lower sliding plate 下滑块板 upper holderblock 上压块 upper mid plate 上中间板 spring box 弹簧箱spring-box eject-rod 弹簧箱顶杆 spring-box eject-plate 弹簧箱顶板 bushing bolck 衬套 cover plate 盖板 guide pad 导料块塑件&模具相关英文 pre sion molding 压缩成型 flash mold 溢流式模具plsitive mold 挤压式模具 split mold 分割式模具 cavity 型控母模 core 模心公模 taper 锥拔 leather cloak 仿皮革 shiver 饰纹 flow mark 流痕 welding mark 溶合痕 post screw insert 螺纹套筒埋值 self tapping screw 自攻螺丝 striper plate 脱料板 piston 活塞 cylinder 汽缸套 chip 细碎物 handle mold 手持式模具移转成型用模具 encapsulation molding 低压封装成型射出成型用模具 two plate 两极式（模具） well type 蓄料井insulated runner 绝缘浇道方式 hot runner 热浇道 runner plat 浇道模块 valve gate 阀门浇口 band heater 环带状的电热器spindle 阀针 spear head 刨尖头 slag well 冷料井 cold slag 冷料渣 air vent 排气道 h=0.02~0.05mm w=3.2mm L=3~5mm welding line 熔合痕 eject pin 顶出针 knock pin 顶出销return pin 回位销反顶针 sleave 套筒 stripper plate 脱料板insert core 放置入子 runner stripper plate 浇道脱料板 guide pin 导销 eject rod (bar)（成型机）顶业捧 subzero 深冷处理three plate 三极式模具 runner system 浇道系统 stress crack 应力电裂 orientation 定向 sprue gate 射料浇口，直浇口nozzle 射嘴 sprue lock pin 料头钩销(拉料杆) slag well 冷料井 side gate 侧浇口 edge gate 侧缘浇口 tab gate 搭接浇口film gate 薄膜浇口 flash gate 闸门浇口 slit gate 缝隙浇口fan gate 扇形浇口 dish gate 因盘形浇口 H=F=1/2t~1/5tT=2.5~3.5mm diaphragm gate 隔膜浇口 ring gate 环形浇口subarine gate 潜入式浇口 tunnel gate 隧道式浇口 pin gate 针点浇口Φ0.8~1.0mm Runner less 无浇道 (sprue less)无射料管方式 long nozzle 延长喷嘴方式 sprue 浇口;溶渣品质人员名称类 QC quality control 品质管理人员 FQC final qualitycontrol 终点品质管制人员 IC in process quality control 制程中的品质管制人员 OQC output quality control 最终出货品质管制人员 IQC ining quality control 进料品质管制人员 TQC total quality control 全面质量管理 POC passage quality control 段检人员 QA quality assurance 质量保证人员 OQA output quality assurance 出货质量保证人员 QE quality engineering 品质工程人员品质保证类 FAI first article inspection 新品首件检查FAA first article assurance 首件确认 TVR tool verification report 模具确认报告 3B 3B 模具正式投产前确认 CP capability index 能力指数 CPK capability index of process 模具制程能力参数 SSQA standardized supplier quality 合格供应商品质评估OOBA out of box audit 开箱检查 QFD quality function deployment 品质机能展开 FMEA failure model effectiveness analysis 失效模式分析 8 disciplines 8 项回复内容 FA final audit 最後一次稽核 CAR corrective action request 改正行动要求 corrective action report 改正行动报告 FQC 运作类 AQL Aeptable Quality Level 运作类允收品质水准 S/S Sample size 抽样检验样本大小 ACC Aept 允收 REE Reject 拒收 CR Critical 极严重的 MAJ Major 主要的 MIN Minor 轻微的 AOQ Average Output Quality 平均出厂品质 AOQL Average Output QualityLevel 平均出厂品质 Q/R/S Quality/Reliability/Service 品质/可靠度效劳 MIL-STD Military-Standard 军用标准 S I-S IV Special I-Special IV 特殊抽样水准等级 P/N Part Number 料号L/N Lot Number 特采 AOD Aept On Deviation 特采 UAI Use As It 首件检查报告 FPIR First Piece Inspection Report 百万分之一 PPM Percent Per Million 批号制程统计品管专类 SPC Statistical Process Control 统计制程管制 SQC Statistical Quality Control统计品质管制 R Range 全距 AR Averary Range 全距平均值 UCL Upper Central Limit 管制上限 LCL Lower Central Limit 管制下限 MAX Maximum 最大值 MIN Minimum 最小值 GRR Gauge Reproducibility&Repeatability 量具之再制性及重测性判断量可靠与否 DIM Dimension 尺寸 DIA Diameter 直径 FREQ Frequency 频率 N Number 样品数其它品质术语类 QCC Quality Control Circle 品质圈 QIT Quality Improvement Team 品质改善小组PDCA Plan Do Check Action 方案执行检查总结 ZD Zero Defect 零缺点 QI Quality Improvement 品质改善 QP Quality Policy 目标方针 TQM Total Quality Management 全面品质管理MRB Material Reject Bill 退货单 LQL Limiting Quality Level 最低品质水准 RMA Return Material Audit 退料认可 QAN Quality Amelionrate Notice 品质改善活动 ADM Absolute Dimension Measuremat 全尺寸测量 QT Quality Target 品质目标 7QCTools 7 Quality Controll Tools 品管七大手法通用之件类 E Engineering Change Notes 工程变更通知(供应商) ECO Engineering Change Order 工程改动要求(客户) P ProcessChange Notice 工序改动通知 PMP Product Management Plan 生产管制方案 SIP Specification In Process 制程检验规格 SOP Standard Operation Procedure 制造作业标准 IS Inspection Specification 成品检验标准 BOM Bill Of Material 物料清单 PS Package Specification 包装标准 SPEC Specification 规格 DWG Drawing 图面系统文件类 QC Quality System 品质系统 ES Engineering Standarization 工程标准 CGOO China General PCE 龙华厂文件 H Huston (美国)休斯敦 C Compaq (美国)康伯公司 C China 中国大陆 A Assembly 组装(厂) S Stamping 冲压(厂) P Painting 烤漆(厂) I Intel 英特尔公司 T TAIWAN IWS International Workman Standard 工艺标准 ISO International Standard Organization 国际标准化组织 GS General Specification 一般规格 CMCS C-China M-Manufact C-Compaq S-Stamping Compaq产品在龙华冲压厂制造作业标准 CQCA Q-Quality A-Assembly Compaq 产品在龙华组装厂品管作业标准 CQCP P-Painting Compaq 产品在龙华烤漆厂品管作业标准部类 PMC Production & Material Control 生产和物料控制 PPC Production Plan Control 生产方案控制 MC Material Control 物料控制 ME Manafacture Engineering 制造工程部 PE Project Engineering 产品工程部 A/C Aountant Dept 会计部 P/A Personal & Administration 人事行政部 DC Document Center 资料中心 QE Quality Engineering 品质工程(部) QA Quality Assurance 品质保证(处) QC Quality Control 品质管制(课) PD Product Department 生产部 LAB Labratry 实验室 IE Industrial Engineering 工业工程 R&D Research & Design 设计开发部 PPainting 烤漆(厂) A Asssembly 组装(厂) S Stamping 冲压(厂) 生产类 PCS Pieces 个(根,块等) PRS Pairs 双(对等) CTN Carton 卡通箱 PAL Pallet/skid 栈板 PO Purchasing Order 采购订单 MO Manufacture Order 生产单 D/C Date Code 生产日期码 ID/C Identification Code (供应商)识别码 SWR Special Work Request 特殊工作需求 L/N Lot Number 批号 P/N Part Number 料号其它OEM Original Equipment Manufacture 原设备制造 PCE Personal Computer nclosure 个人电脑外设 PC Personal Computer 个人电脑 CPU Central Processing Unit 中央处理器 SECC SECC` 电解片SGCC SGCC 热浸镀锌材料 NHK North of Hongkong 中国大陆 PRC People"s Republic of China 中国大陆（中华人民共和国） U.S.A the United States of America 美国 A.S.A.P As Soon As Possible 尽可能快的 E-MAIL Electrical-Mail 电子邮件 N/A Not Applicable 不适用 QTY Quantity 数量 VS 以及 REV Revision 版本 JIT Just In Time 零库存 I/O Input/Output 输入/输出 OK Ok 好 NG Not Good 不行,不合格 C=0 Critical=0 极严重不允许 ESD Electry-static Discharge 静电排放 5S 希腊语 ,整顿,清扫,清洁,教养ATIN Attention 知会 CC Carbon Copy 副本复印相关人员 APP Approve 核准,认可,成认 CHK Check 确认 AM Ante Meridian 上午PM Post Meridian 下午 CD Compact Disk 光碟 CD-ROM Compact Disk Read-Only Memory 只读光碟 FDD Floppy Disk Drive 软碟机HDD Hard Disk Drive 碟碟机 REF Reference CONN Connector 连接器 CAV Cavity 模穴 CAD Computer Aid Design 计算机辅助设计ASS"Y Assembly 装配,组装 MAT"S Material 材料 IC IntegratedCircuit 集成电路 T/P True Position 真位度 TYP Type 类型 WDR Weekly Delivery Requitement 周出货需求 C/T Cycle Time 制程周期 L/T Lead Time 前置时间(生产前准备时间) S/T Standard Time 标准时间 P/M Product Market 产品市场 3CComputer,Commumcation,Consumer electronic"s 消费性电子 5WIH When,Where,Who,What,Why,How to 5MMan,Machine,Material,Method,Measurement 4MIHMan,Materia,Money,Method,Time 人力,物力,财务,技术,时间(资源) SQA Strategy Quality Assurance 策略品质保证 DQA Desigh Quality Assurance 设计品质保证 MQA Manufacture Quality Assurance 制造品质保证 SSQA Sales and service Quality Assurance 销售及效劳品质保证 LRR Lot Rejeet Rate 批退率 BS Brain storming 脑力激荡 EMI Electronic Magion Inspect 高磁测试 FMI Frequency Modulatim Inspect 高频测试 B/MBoar/Molding(flat cable) C/P Connector of PC A/P Assembly SPS Switching power supply 电源箱 DT Desk Top 卧式(机箱) MT Mini-Tower 立式(机箱) DVD Digital Vedio Disk VCD Vdeio Compact Disk LCD Liquid Crystal Display CAD Computer AID Design CAM Computer AID Manufacturing CAE Computer AID Engineering ABIOS Achanced Basic in put/output system 先进的根本输入/输出系统 CMOS Complemeruary Metoll Oxide Semiconductor 互补金属氧化物半导体 PDA Personal Digital Assistant 个人数字助理 IC Integrated Circuit 集成电路 ISA Industry Standard Architecture 工业标准体制结构 MCA Micro Channel Architecture 微通道结构 EISA Extended IndustryStandard Architecture 扩充的工业标准结构 SIMM Single in-line memory module 单项导通汇流组件 DIMM Dual in-line Memory Module 双项导通汇流组件 LED Light-Emitting Diode 发光二级管 FMEA Failure Mode Effectivenes 失效模式分析 W/H Wire Harness 金属线绪束集组件 F/C Flat Calle 排线 PCB Printed Circuit Board 印刷电路板 CAR Correction Action Report 改善报告 NG Not Good 不良 WPR Weekly Delivery Requirement 周出货要求 PPM Parts Per Million 百万分之一 TPM Total Production Maintenance 全面生产保养 MRP Material Requiremt Planning 物料需方案 OC Operation System 作业系统TBA To Be Design 待定,定缺 D/C Drawing Change P/P Plans & Procedune EMI Electrical-Music Industry 电子音乐工业 RFI Read Frequency Input 读频输入 MMC Maximum Material ondition MMS Maximum Material Size LMC Least Material Condition LMS Least Material Size模具技术用语各种模具常用成形方式 aurate die casting 精密压铸 powder forming 粉末成形 calendaring molding 压延成形 powder metal forging 粉末锻造 cold chamber die casting 冷式压铸 precision forging 精密锻造 cold forging 冷锻 press forging 冲锻 pacting molding 粉末压出成形 rocking die forging 摇动锻造 pound molding 复合成形 rotary forging 回转锻造 pression molding 压缩成形 rotational molding 离心成形dip mold 浸渍成形 rubber molding 橡胶成形 encapsulation molding 注入成形 sand mold casting 砂模铸造 extrusion molding 挤出成形 shell casting 壳模铸造 foam forming 泡成形sinter forging 烧结锻造 forging roll 轧锻 six sides forging 六面锻造 gravity casting 重力铸造 slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形 squeeze casting 高压铸造 hot chamber die casting 热室压铸 swaging 挤锻 hotforging 热锻 transfer molding 转送成形 injection molding 射出成形 warm forging 温锻 investment casting 精密铸造matched die method 对模成形法 laminating method 被覆淋膜成形 low pressure casting 低压铸造 lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模 landed plunger mold 有肩柱塞式模具burnishing die 挤光模 landed positive mold 有肩全压式模具button die 镶入式圆形凹模 loading shoe mold 料套式模具center-gated mold 中心浇口式模具 loose detail mold 活零件模具 chill mold 冷硬用铸模 loose mold 活动式模具 clod hobbing 冷挤压制模 louvering die 百叶窗冲切模 posite dies 复合模具manifold die 分歧管模具 counter punch 反凸模 modular mold 组合式模具 double stack mold 双层模具 multi-cavity mold 多模穴模具 electroformed mold 电铸成形模 multi-gate mold 复式浇口模具 expander die 扩径模 offswt bending die 双折冷弯模具 extrusion die 挤出模 palletizing die 叠层模 family mold 反套制品模具 plaster mold 石膏模 blank through dies 漏件式落料模 porous mold 通气性模具 duplicated cavity plate 复板模 positive mold 全压式模具 fantail die 扇尾形模具pressure die 压紧模 fishtail die 鱼尾形模具 profile die 轮廓模 flash mold 溢料式模具 progressive die 顺序模 gypsummold 石膏铸模 protable mold 手提式模具 hot-runner mold 热流道模具 prototype mold 雏形试验模具 ingot mold 钢锭模punching die 落料模 lancing die 切口模 raising(embossing) 压花起伏成形 re-entrant mold 倒角式模具 sectional die 拼合模 runless injection mold 无流道冷料模具 sectional die 对合模具 segment mold 组合模 semi-positive mold 半全压式模具shaper 定型模套 single cavity mold 单腔模具 solid forging die 整体锻模 split forging die 拼合锻模 split mold 双并式模具 sprueless mold 无注道残料模具 squeezing die 挤压模stretch form die 拉伸成形模 sweeping mold 平刮铸模 swing die 振动模具 three plates mold 三片式模具 trimming die 切边模 unit mold 单元式模具 universal mold 通用模具 unscrewing mold 退扣式模具 yoke type die 轭型模模具厂常用之标准零配件air vent vale 通气阀 anchor pin 锚梢 angular pin 角梢baffle 调节阻板 angular pin 倾斜梢 baffle plate 折流档板ball button 球塞套 ball plunger 定位球塞 ball slider 球塞滑块 binder plate 压板 blank holder 防皱压板 blanking die 落料冲头 bolster 上下模板 bottom board 浇注底板 bolster 垫板bottom plate 下固定板 bracket 托架 bumper block 缓冲块buster 堵口 casting ladle 浇注包 casting lug 铸耳 cavity 模穴(模仁) cavity retainer plate 模穴托板 center pin 中心梢clamping block 锁定块 coil spring 螺旋弹簧 cold punched nut 冷冲螺母 cooling spiral 螺旋冷却栓 core 心型 core pin 心型梢 cotter 开口梢 cross 十字接头 cushion pin 缓冲梢diaphragm gate 盘形浇口 die approach 模头料道 die bed 型底die block 块形模体die body 铸模座 die bush 合模衬套 die button 冲模母模 die clamper 夹模器 die fastener 模具固定用零件 die holder 母模固定板 die lip 模唇 die plate 冲模板 die set 冲压模座direct gate 直接浇口 dog chuck 爪牙夹头 dowel 定位梢 dowel hole 导套孔 dowel pin 合模梢 dozzle 辅助浇口 dowel pin 定位梢 draft 拔模锥度 draw bead 张力调整杆 drive bearing 传动轴承 ejection pad 顶出衬垫 ejector 脱模器 ejector guide pin 顶出导梢 ejector leader busher 顶出导梢衬套 ejector pad 顶出垫 ejector pin 顶出梢 ejector plate 顶出板 ejector rod 顶出杆 ejector sleeve 顶出衬套 ejector valve 顶出阀 eye bolt 环首螺栓 filling core 椿入蕊 film gate 薄膜形浇口 finger pin 指形梢 finish machined plate 角形模板 finish machined round plate 圆形模板 fixed bolster plate 固定侧模板 flanged pin 带凸缘 flash gate 毛边形浇口 flask 上箱 floating punch 浮动冲头 gate 浇口 gate land 浇口面 gib 凹形拉紧? goose neck 鹅颈管 guide bushing 引导衬套 guide pin 导梢 guide post 引导柱 guide plate 导板 guide rail 导轨 head punch 顶?冲头 headless punch 直柄冲头 heavily tapered solid 整体模蕊盒 hose nippler 管接头 impact damper 缓冲器 injection ram 压射柱塞 inlay busher 嵌入衬套 inner plunger 内柱塞 inner punch 内冲头 insert 嵌件 insert pin 嵌件梢 king pin 转向梢king pin bush 主梢衬套 knockout bar 脱模杵 land 合模平坦面land area 合模面 leader busher 导梢衬套 lifting pin 起模顶?。

机械类各行业专业英语词汇1. 汽车行业 (Automotive Industry)•Engine（发动机）•Transmission（传动装置）•Suspension（悬挂系统）•Brake（刹车系统）•Steering（转向系统）•Exhaust system（排气系统）•Fuel injection（燃油喷射系统）•Tire（轮胎）•Battery（电池）•Alternator（发电机）2. 航空航天工业 (Aerospace Industry)•rcraft（飞机）•Wing（机翼）•Fuselage（机身）•Cockpit（驾驶舱）•Landing gear（起落架）•Jet engine（喷气发动机）•leron（副翼）•Thrust（推力）•Propeller（螺旋桨）•Avionics（航空电子设备）3. 重工业 (Heavy Industry)•Machinery（机械）•Crane（起重机）•Bulldozer（推土机）•Excavator（挖掘机）•Boiler（锅炉）•Conveyor belt（输送带）•Generator（发电机）•Drill（钻机）•Foundry（铸造厂）•Welding（焊接）4. 电子行业 (Electronics Industry)•Circuit board（电路板）•Microchip（微芯片）•Transistor（晶体管）•Capacitor（电容器）•Resistor（电阻器）•Diode（二极管）•Integrated circuit（集成电路）•Semiconductor（半导体）•Printed circuit board (PCB)（印刷电路板）•Soldering（焊接）5. 工程机械 (Construction Machinery)•Cranes（起重机）•Excavators（挖掘机）•Bulldozers（推土机）•Loaders（装载机）•Rollers（压路机）•Pavers（铺路机）•Concrete mixer（混凝土搅拌机）•Tower crane（塔式起重机）•Trencher（挖沟机）•Forklift（叉车）6. 机床行业 (Machine Tool Industry)•Lathe（车床）•Milling machine（铣床）•Drilling machine（钻床）•Grinding machine（磨床）•Boring machine（镗床）•Shaping machine（拉坯机）•CNC machine tool（数控机床）•Power press（压力机）•Shearing machine（剪板机）•Woodworking machine（木工机械）7. 包装机械 (Packaging Machinery)•Filling machine（灌装机）•Sealing machine（封口机）•Labeling machine（贴标机）•Capping machine（旋盖机）•Wrapping machine（包装机）•Coding machine（打码机）•Shrinking machine（收缩机）•Vacuum packaging machine（真空包装机）•Cartoning machine（装箱机）•Palletizing machine（托盘包装机）8. 纺织机械 (Textile Machinery)•Spinning machine（纺纱机）•Weaving machine（织布机）•Knitting machine（针织机）•Dyeing machine（染色机）•Printing machine（印花机）•Stenter machine（拉伸机）•Embroidery machine（绣花机）•Textile finishing machine（纺织整理机）•Yarn twisting machine（纱线捻接机）•Textile testing equipment（纺织测试设备）9. 精密仪器 (Precision Instruments)•Optical microscope（光学显微镜）•Electronic balance（电子天平）•Spectrophotometer（分光光度计）•Ultrasonic cleaner（超声波清洗机）•Atomic force microscope (AFM)（原子力显微镜）•Mass spectrometer（质谱仪）•X-ray diffractometer（X射线衍射仪）•Scanning electron microscope (SEM)（扫描电子显微镜）•Electron beam lithography (EBL)（电子束曝光机）•Surface profilometer（表面粗糙度仪）10. 医疗器械 (Medical Devices)•MRI machine（核磁共振机）•CT scanner（计算机断层扫描仪）•X-ray machine（X射线机）•Ultrasound machine（超声波仪）•Surgical microscope（手术显微镜）•Electrocardiogram (ECG) machine（心电图机）•Defibrillator（除颤仪）•Anesthesia machine（麻醉机）•Blood pressure monitor（血压监测仪）•Thermometer（体温计）以上是机械类各行业中常见的专业英语词汇。

机械专业中英文单词总汇在机械专业这一广受欢迎的学科领域内，涉及到了大量的专业术语和专用单词，这些单词既是机械专业学习的基础，也是从事机械工程的人们必须熟练掌握的基本素材。

随着机械专业的深入发展，机械工程的知识也在不断更新和拓展，涉及到的专业术语也不断增多。

下面是一份机械专业中英文单词总汇，帮助大家更好的了解和学习机械工程专业知识。

1. ball bearing——滚珠轴承2. cam follower——凸轮从动器3. connecting rod——连杆4. crankshaft——曲轴5. cylinder——气缸6. gear ratio——传动比7. hydraulic motor——液压马达8. piston ring——活塞环9. rack and pinion——齿轮齿条10. reciprocating motion——往复运动11. transmission——传动12. turbine——涡轮机13. velocity ratio——速比14. worm gear——蜗轮蜗杆15. actuator——执行器16. air compressor——空气压缩机17. ball screw——滚珠丝杠18. bearing——轴承19. belt drive——皮带传动20. brake——制动器21. cam——凸轮22. clutch——离合器23. combustion engine——内燃机24. compressibility——可压缩性25. compressive stress——压应力26. conveyor——传送带27. cooling system——冷却系统28. crank——曲柄29. cutaway——剖视图30. cyanoacrylate——氰基丙烯酸甲酯31. cylinder head——缸盖32. decomposition——分解33. diesel engine——柴油机34. dimension——尺寸35. dowel pin——销36. drive shaft——传动轴37. elasticity——弹性38. end mill——端铣刀39. engine block——发动机缸体40. exhaust system——排气系统41. flywheel——飞轮42. fuel injection——燃油喷射43. fuel pump——燃油泵44. gear——齿轮45. governor——调速器46. heat capacity——热容47. heat exchanger——热交换器48. helical gear——螺旋齿轮49. hydraulic valve——液压阀50. ignition——点火51. lathe——车床52. lubrication——润滑53. machine——机器54. machining——加工55. machine tool——机床56. mechanical engineering——机械工程57. metalworking——金属加工58. milling——铣削59. nut——螺母60. oil pump——油泵61. piston——活塞62. pneumatic——气动的63. power supply——电源64. pressure——压力65. pulley——滑轮66. push rod——推杆67. quick coupler——快速接头68. relief valve——安全阀69. roller——辊70. rotary motion——旋转运动71. rotor——转子72. screw——螺钉73. sensor——传感器74. shear stress——剪应力75. spring——弹簧76. spur gear——直齿轮77. square hole——方孔78. thrust bearing——推力轴承79. tolerance——公差80. torque——扭矩81. universal joint——万向节82. valve——阀门83. vibration——振动84. voltage——电压85. washer——垫圈86. welding——焊接87. worm——蜗杆88. XL belt——XL带89. yoke——箍90. zipper——拉链以上是机械专业中的常用单词和专业术语的汇总，掌握这些单词能够帮助学习者更好的理解机械专业的知识，同时能够提高从事机械工程工作的人们的技能素养，为机械工程的发展和创新添砖加瓦。

机械专业英语词汇金属切削metal cutting [英] [ˈmetl][美] [ˈmɛtl]机床machine tool [英] [məˈʃi:n tu:l][美] [məˈʃin tul] 金属工艺学technology of metals [tekˈnɔlədʒi] [ˈmetl] 刀具cutter['kʌtɚ]摩擦friction['frikʃən][’frɪkʃən]联结link [liŋk]传动drive/transmission [trænzˈmiʃən]轴shaft [ʃɑ:ft]弹性elasticity[ɪlæ'stɪsɪti:, ,i:læ-][ɪlæ'stɪsɪti, ,ilæ-]频率特性frequency characteristic['fri:kwənsi][ˌkæriktəˈristik]误差error[ˈerə]响应response[ri'spɔns]定位allocation[ˌæləˈkeiʃən]机床夹具jig[dʒɪg]动力学dynamic[dai'næmik]运动学kinematic[,kaini'mætik]静力学static[ˈstætik]分析力学analyse mechanics[ˈænəlaiz] .[mɪˈkænɪks] 拉伸pulling['puliŋ]压缩hitting[hitiŋ]剪切shear[ʃiə]扭转twist[twist]弯曲应力bending stress['bendiŋ] .[stres]强度intensity[inˈtensiti]三相交流电three-phase AC[feiz] 磁路magnetic circles[mæɡˈnetik] .[ˈsə:kl]变压器transformer[trænsˈfɔ:mə]异步电动机asynchronous motor[ei'siŋkrənəs] ['məutə]几何形状geometrical[dʒɪəˈmetrɪkəl]精度precision[priˈsiʒən]正弦形的sinusoid[ˈsainəˌsɔid]交流电路AC circuit [ˈsə:kit]机械加工余量machining allowance [mə'ʃi:niŋ] .[əˈlauəns]变形力deforming force [dɪˈfɔ:miŋ] .[fɔ:s]变形deformation [ˌdi:fɔ:ˈmeɪʃən, ˌdefə-]应力stress [stres]硬度rigidity [rɪˈdʒɪdɪti:]]热处理heat treatment [ˈtri:tmənt]退火anneal [əˈni:l]正火normalizing ['nɔ:məlaiziŋ]脱碳decarburization [di:,kɑ:bjuərai'zeiʃən]渗碳carburization [,kɑ:bjurai'zeiʃən]电路circuit [ˈsə:kit]半导体元件semiconductor element [ˌsemikənˈdʌktə] .[ˈelimənt] 反馈feedback [ˈfi:dbæk]发生器generator [ˈdʒenəreitə]直流电源DC electrical source [i'lektrikəl] .[sɔ:s]门电路gate circuit [ɡeit] [ˈsə:kit]逻辑代数logic algebra [ˈlɔdʒik] .[ˈældʒibrə]外圆磨削external grinding [eksˈtə:nl] ['ɡraindiŋ]内圆磨削internal grinding [inˈtə:nəl] ['ɡraindiŋ]平面磨削plane grinding [plein] ['ɡraindiŋ]变速箱gearbox [ˈɡiəbɔks]离合器clutch [klʌtʃ]绞孔fraising [freiziŋ]绞刀reamer .[ˈri:mə]螺纹加工thread processing [θred] .[prəʊˈsesɪŋ]螺钉screw [skru:]铣削mill [mil]铣刀milling cutter [ˈmiliŋ] .[ˈkʌtə]功率power [ˈpauə]工件workpiece [ˈwɜ:kpi:s]齿轮加工gear machining [ɡiə] [mə'ʃi:niŋ]齿轮gear [ɡiə]主运动main m ovement [mein] .[ˈmu:vmənt]主运动方向direction of main movement [diˈrekʃən]进给方向direction of feed [diˈrekʃən] .[fi:d]进给运动feed movement [fi:d] [ˈmu:vmənt]合成进给运动resultant movement of feed [riˈzʌltənt] [ˈmu:vmənt] [fi:d]合成切削运动resultant movement of cu tting [riˈzʌltənt] [ˈmu:vmənt][ˈkʌtɪŋ]合成切削运动方向direction of resultant movement of cutting [diˈrekʃən] [riˈzʌltənt] [ˈmu:vmənt] [ˈkʌtɪŋ]切削深度cutting depth [ˈkʌtɪŋ] .[depθ]前刀面rake face [reik][ feis]刀尖nose of tool [nəuz] .[tu:l]前角rake angle [reik] .[ˈæŋɡl] 后角clearance angle [ˈkliərəns] .[ˈæŋɡl]龙门刨削planing [plæniŋ]主轴spindle [ˈspɪndl]主轴箱headstock [ˈhedstɔk]卡盘chuck [tʃʌk]加工中心machining center [mə'ʃi:niŋ]车刀lathe tool [leɪð] .[tu:l]车床lathe [leɪð]钻削镗削bore [bɔ:]车削turning [ˈtɜ:nɪŋ]磨床grinder [ˈgraɪndə]基准benchmark [ˈbentʃˌmɑ:k]钳工locksmith [ˈlɔkˌsmɪθ]锻forge [fɔ:dʒ]压模stamping [ˈstæmpiŋ]焊weld [weld]拉床broaching machine ['brəutʃiŋ] .[məˈʃi:n]拉孔broaching['brəutʃiŋ]装配assembling [ə'sembliŋ]铸造found [faund]流体动力学fluid dynamics ['flu(:)id] [dai'næmiks]流体力学fluid mechanics ['flu(:)id] [mi'kæniks]加工machining [mə'ʃi:niŋ]液压hydraulic pressure [hai'drɔ:lik] ['preʃə]切线tangent ['tændʒənt]机电一体化mechanotronics mechanical-electrical integration [,mekənə'trɔniks] [mi'kænikl] [i'lektrikəl] [,inti'ɡreiʃən]气压air pressure pneumatic pressure [nju(:)'mætik] 稳定性stability [stə'biliti]介质medium ['mi:djəm]液压驱动泵fluid clutch ['flu(:)id] [klʌtʃ]液压泵hydraulic pump [hai'drɔ:lik] [pʌmp]阀门valve [vælv]失效invalidation [in'vælideiʃn]强度intensity [in'tensiti]载荷load [ləud]应力stress [stres]安全系数safety factor ['seifti] ['fæktə]可靠性reliability [ri,laiə'biliti]螺纹thread [θred]螺旋helix ['hi:liks]键spline [splain]销pin [pin]滚动轴承rolling bearing ['rəuliŋ] ['bɛəriŋ]滑动轴承sliding bearing ['slaidiŋ] ['bɛəriŋ]弹簧spring [spriŋ]制动器arrester brake [ə'restə] [breik]十字结联轴节crosshead ['krɔshed]联轴器coupling ['kʌpliŋ]链chain [tʃein]皮带strap [stræp]精加工finish machining ['finiʃ] [mə'ʃi:niŋ]粗加工rough machining [rʌf] [mə'ʃi:niŋ] 变速箱体gearbox casing ['ɡiəbɔks] ['keisiŋ]腐蚀rust [rʌst]氧化oxidation [ɔksi'deiʃən]磨损wear [wɛə]耐用度durability [,djuərə'biliti]随机信号random signal ['rændəm] ['siɡnl]离散信号discrete signal [dis'kri:t] ['siɡnl]超声传感器ultrasonic sensor ['ʌltrə'sɔnik] ['sensə]集成电路integrate circuit ['intiɡreit] ['sə:kit]挡板orifice plate ['ɔrifis] [pleit]残余应力residual stress [ri'zidjuəl] [stres]套筒sleeve [sli:v]扭力torsion ['tɔ:ʃən]冷加工cold machining [mə'ʃi:niŋ]电动机electromotor [i,lektrəu'məutə]汽缸cylinder ['silində]过盈配合interference fit [,intə'fiərəns] [fit]热加工hot work [hɔt] [wə:k]摄像头CCD camera ['kæmərə]倒角rounding chamfer ['raundiŋ] ['tʃæmfə]优化设计optimal design ['ɔptiməl] [di'zain]工业造型设计industrial moulding design [in'dʌstriəl] ['məuldiŋ] [di'zain]有限元finite element ['fainait] ['elimənt]滚齿hobbing ['hɔbiŋ]插齿gear shaping [ɡiə] ['ʃeipiŋ]伺服电机actuating motor ['æktjueitiŋ] ['məutə]铣床milling machine ['miliŋ] [mə'ʃi:n]钻床drill machine [dril] [mə'ʃi:n]镗床boring machine ['bɔ:riŋ] [mə'ʃi:n]步进电机stepper motor ['stepə] ['məutə]丝杠screw rod [skru:] [rɔd]导轨lead rail [li:d] [reil]组件subassembly ['sʌbə'sembli]可编程序逻辑控制器Programmable Logic Controller PLC ['prəuɡræməbl] ['lɔdʒik] [kən'trəulə]电火花加工electric spark machining [i'lektrik] [spɑ:k] [mə'ʃi:niŋ] 电火花线切割加工electrical discharge wire –cutting [i'lektrikəl] [dis'tʃɑ:dʒ]相图phase diagram [feiz] ['daiəɡræm]固态相变solid state phase changes [feiz]有色金属nonferrous metal ['nɔn'ferəs] ['metl]陶瓷ceramics [si'ræmiks]合成纤维synthetic fibre [sin'θetic] ['faibə]电化学腐蚀electrochemical corrosion [i,lektrəu'kemikəl] [kə'rəuʒən]车架automotive chassis [ɔ:tə'məutiv] ['ʃæsi]悬架suspension [səs'penʃən]转向器redirector ['ri:di'rektə]变速器speed changer [spi:d] ['tʃeindʒə]板料冲压sheet metal parts [ʃi:t] ['metl] [pɑ:ts]孔加工spot facing machining [spɔt] ['feisiŋ] [mə'ʃi:niŋ]车间workshop ['wə:kʃɔp]工程技术人员engineer [,endʒi'niə]气动夹紧pneuma lock ['nju:mə] [lɔk] 数学模型mathematical model [,mæθi'mætikəl]画法几何descriptive geometry [dis'kriptiv] [dʒi'ɔmitri] 机械制图Mechanical drawing [mi'kænikl] ['drɔ:iŋ]投影projection [prə'dʒekʃən]视图view [vju:]剖视图profile chart ['prəufail] [tʃɑ:t]标准件standard component ['stændəd] [kəm'pəunənt] 零件图part drawing [pɑ:t] ['drɔ:iŋ]装配图assembly drawing [ə'sembli] ['drɔ:iŋ]尺寸标注size marking [saiz] ['mɑ:kiŋ]技术要求technical requirements刚度rigidity [ri'dʒiditi]内力internal force [in'tə:nl] [fɔ:s]位移displacement [dis'pleismənt]截面section ['sekʃən]疲劳极限fatigue limit [fə'ti:ɡ] ['limit]断裂fracture ['fræktʃə]塑性变形plastic distortion ['plæstik, plɑ:stik] [dis'tɔ:ʃən] 脆性材料brittleness material ['britl] [mə'tiəriəl]刚度准则rigidity criterion [ri'dʒiditi] [krai'tiəriən]垫圈washer ['wɔʃə]垫片spacer ['speisə]直齿圆柱齿straight toothed spur gear [tu:ðd] [spə:]斜齿圆柱齿轮helical-spur gear ['helikəl] [spə:][ɡiə]直齿锥齿轮straight bevel gear [streit] ['bevəl] [ɡiə]运动简图kinematic sketch [,kaini'mætik] [sketʃ]齿轮齿条pinion and rack ['pinjən] [ræk]蜗杆蜗轮worm and worm gear [wə:m] [ɡiə]虚约束passive constraint ['pæsiv] [kən'streint]曲柄crank [kræŋk]摇杆racker ['rækə]凸轮cams [kæm]共轭曲线conjugate curve ['kɔndʒuɡit] [kə:v]范成法generation method [,dʒenə'reiʃən] ['meθəd]定义域definitional domain [,defi'niʃən] [dəu'mein]值域range [reindʒ]导数\\微分differential coefficient [,difə'renʃəl][kəui'fiʃənt]求导derivation [deri'veiʃən]定积分definite integral ['definit] ['intiɡrəl]不定积分indefinite integral [in'definit] ['intiɡrəl]曲率curvature ['kə:vətʃə]偏微分partial differential ['pɑ:ʃəl] [,difə'renʃəl]毛坯rough [rʌf]游标卡尺slide caliper [slaid] ['kælipə]千分尺micrometer calipers [mai'krɔmitə] ['kælipəs]攻丝tap [tæp]二阶行列式second order determinant ['sekənd] [' ɔ:də] [di'tə:minənt]逆矩阵inverse matrix ['in'və:s] ['meitriks]线性方程组linear equations ['liniə] [i'kweiʃən]概率probability [,prɔbə'biliti]随机变量random variable ['rændəm] ['vɛəriəbl] 排列组合permutation and combination [,pə:mju(:)'teiʃən][,kɔmbi'neiʃən]气体状态方程equation of state of gas [i'kweiʃən] [steit] [ɡæs]动能kinetic energy [kai'netik] ['enədʒi]势能potential energy [pə'tenʃəl] ['enədʒi]机械能守恒conservation of mechanical energy [,kɔ nsə(:)'veiʃən] [mi'kænikl] ['enədʒi]动量momentum [məu'mentəm]桁架truss [trʌs]轴线axes ['æksi:z]余子式cofactor [kəu'fæktə]逻辑电路logic circuit ['lɔdʒik] ['sə:kit]触发器flip-flop ['flipflɔp]脉冲波形pulse shape [pʌls] [ʃeip]数模digital analogy ['didʒitl] [ə'nælədʒi]液压传动机构fluid drive mechanism ['flu(:)id] [draiv] ['mekənizəm] 机械零件mechanical parts [mi'kænikl] [pɑ:t]淬火冷却quench [kwentʃ]淬火hardening ['hɑ:dəniŋ]回火tempering ['tempəriŋ]调质hardening and tempering ['hɑ:dəniŋ] ['tempəriŋ]磨粒abrasive grain [ə'breisiv] [ɡrein]结合剂bonding agent ['bɔndiŋ] ['eidʒənt]砂轮grinding wheel ['ɡraindiŋ] [wi:l, hw-]机械零件mechanical parts [mi'kænikl] [pɑ:t]淬火冷却quench [kwentʃ]淬火hardening ['hɑ:dəniŋ]回火tempering ['tempəriŋ]调质hardening and tempering ['hɑ:dəniŋ] ['tempəriŋ]磨粒abrasive grain [ə'breisiv] [ɡrein]结合剂bonding agent ['bɔndiŋ] ['eidʒənt]砂轮grinding wheel ['ɡraindiŋ] [wi:l, hw-]机床行业部分英汉对照按英文字母排序3-Jaws indexing spacers[dʒɔ:] ['indeksiŋ] ['speisə]三爪分割工具头A T C system ['sɪstəm]加工中心机刀库Aluminum continuous melting & holding furnaces[ə'lu:mənəm] [kən'tinjuəs] ['meltiŋ] ['həuldiŋ] ['fə:nis] 连续溶解保温炉Balancing equipment ['bælənsiŋ] [i'kwipmənt]平衡设备Bayonet ['beɪənɪt, -,net, ,beɪə'net]卡口Bearing fittings ['bɛəriŋ] ['fitiŋ]轴承配件Bearing processing equipment ['bɛəriŋ] [prəu'sesiŋ][i'kwipmənt]轴承加工机Bearings ['bɛəriŋ]轴承Belt drive [belt] [draɪv]带传动Bending machines ['bendiŋ] [mə'ʃi:n]弯曲机Blades [bleid]刀片Blades,saw [bleid] [sɔ:]锯片Bolts,screws&nuts [bəult][skru:][nʌts]螺栓,螺帽及螺丝Boring heads ['bɔ:riŋ] [hed]搪孔头Boring machines ['bɔ:riŋ] [mə'ʃi:n]镗床Cable making tools ['keibl] ['meikiŋ] [tu:l]造线机Casting,aluminium ['kæstɪŋ] [,ælju:'minjəm]铸铝Casting,copper ['kæstɪŋ] ['kɔpə]铸铜Casting,gray iron ['kæstɪŋ] [ɡrei] ['aiən]铸灰口铁Casting,malleable iron ['kæstɪŋ] ['mæliəbl]可锻铸铁Casting,other ['kæstɪŋ]其他铸造Casting,steel ['kæstɪŋ] [sti:l]铸钢Chain drive [tʃein] [draɪv]链传动Chain making tools [tʃein]造链机Chamfer machines ['tʃæmfə] [mə'ʃi:n]倒角机Chucks [tʃʌk]夹盘Clamping/holding systems ['klæmpiŋ]夹具/支持系统CNC bending presses （CNC=Computerized Numerical Control[kəm'pju:tə] [nju(:)'merikəl] [kən'trol]）['bendiŋ] [pres] 电脑数控弯折机CNC boring machines ['bɔ:riŋ] [mə'ʃi:n]电脑数控镗床CNC drilling machines ['driliŋ] [mə'ʃi:n]电脑数控钻床CNC EDMwire-cutting machines（EDM=Electron Discharge Machining [i'lektrɔn] [dis'tʃɑ:dʒ] [mə'ʃi:niŋ]放电加工）[mə'ʃi:n] ['waiə]电脑数控电火花线切削机CNC electric discharge machines [i'lektrik] [dis'tʃɑ:dʒ] [mə'ʃi:n]电脑数控电火花机CNC engraving machines [en'greɪvɪŋ] [mə'ʃi:n]电脑数控雕刻机CNC grinding machines ['ɡraindiŋ] [mə'ʃi:n]电脑数控磨床CNC lathes [leið]电脑数控车床CNC machine tool fittings [mə'ʃi:n] [tu:l] ['fitiŋ]电脑数控机床配件CNC milling machines ['miliŋ] [mə'ʃi:n]电脑数控铣床CNC shearing machines ['ʃiəriŋ] [mə'ʃi:n]电脑数控剪切机CNC toolings CNC ['tu:liŋ]刀杆CNC wire-cutting machines ['waiə] ['kʌtiŋ] [mə'ʃi:n] 电脑数控线切削机Conveying chains [kən'veiiŋ] [tʃein]输送链Coolers ['ku:lə]冷却机Coupling ['kʌpliŋ]联轴器Crimping tools [krimpiŋ] [tu:l]卷边工具Cutters ['kʌtə]刀具Cutting-off machines ['kʌtiŋ] [mə'ʃi:n]切断机Diamond cutters ['daiəmənd] ['kʌtə]钻石刀具Dicing saws ['daisiŋ] [sɔ:]晶圆切割机Die casting dies [dai] ['kɑ:stiŋ]压铸冲模Die casting machines [dai] ['kɑ:stiŋ] [mə'ʃi:n]压铸机Dies-progressive [dai] [prə'ɡresiv]连续冲模Disposable toolholder bits [dis'pəuzəbl] ['tu:l,həuldə] [bit]舍弃式刀头Drawing machines ['drɔ:iŋ] [mə'ʃi:n]拔丝机Drilling machines ['driliŋ] [mə'ʃi:n]钻床Drilling machines bench ['driliŋ] [mə'ʃi:n] [bentʃ]钻床工作台Drilling machines,high-speed ['dri liŋ] [mə'ʃi:n] [hai] [spi:d]高速钻床Drilling machines,multispindle [,m ʌlti] ['spindl]多轴钻床Drilling machines,radial ['driliŋ] [mə'ʃi:n] ['reidjəl]摇臂钻床Drilling machines,vertical ['driliŋ] [mə'ʃi:n] ['və:tikəl] 立式钻床drills [dril]钻头Electric discharge machines(EDM) [i'lektrik] [dis'tʃɑ:dʒ]电火花机Electric power tools [i'lektrik] ['pauə] [tu:l]电动刀具Engraving machines [en'greɪvɪŋ] [mə'ʃi:n]雕刻机Engraving machines,laser [en'greɪvɪŋ] [mə'ʃi:n] ['leizə]激光雕刻机Etching machines ['etʃiŋ] [mə'ʃi:n]蚀刻机Finishing machines ['finiʃiŋ] [mə'ʃi:n]修整机Fixture ['fikstʃə]夹具Forging dies ['fɔ:dʒiŋ] [dai]锻模Forging,aluminium ['fɔ:dʒiŋ] [,ælju:'minjəm]锻铝Forging,cold ['fɔ:dʒiŋ] [kəuld]冷锻Forging,copper ['fɔ:dʒiŋ] ['kɔpə]铜锻Forging,other ['fɔ:dʒiŋ] ['ʌðə]其他锻造Forging,steel ['fɔ:dʒiŋ] [sti:l]钢锻Foundry equipment ['faundri] [i'kwipmənt]铸造设备5 Gear cutting machines [ɡiə] ['kʌtiŋ] [mə'ʃi:n]齿轮切削机Gears [ɡiə]齿轮Gravity casting machines ['ɡræviti] ['kɑ:stiŋ] [mə'ʃi:n]重力铸造机Grinder bench ['ɡraində] [bentʃ]磨床工作台Grinders,thread ['ɡraində] [θred]螺纹磨床Grinders,tools & cutters ['ɡraində] [tu:l] ['kʌtə]工具磨床Grinders,ultrasonic ['ɡraində] ['ʌltrə'sɔnik]超声波打磨机Grinding machines ['ɡraindiŋ] [mə'ʃi:n]磨床Grinding machines,centerless ['ɡraindiŋ] [mə'ʃi:n] ['sentəles]无心磨床Grinding machines,cylindrical [si'lindrik(ə)l]外圆磨床Grinding machines,universal [,ju:ni'və:səl]万能磨床Grinding tools ['ɡraindiŋ] [tu:l]磨削工具Grinding wheels ['ɡraindiŋ] [wi:l, hw-]磨轮Hand tools [hænd] [tu:l]手工具Hard/soft and free expansion sheet making plant[iks'pænʃən] [ʃi:t]硬(软)板(片)材及自由发泡板机组Heat preserving furnaces [pri'zə:v] ['fə:nis]保温炉Heating treatment funaces ['tri:tmənt] ['fə:nis]熔热处理炉Honing machines ['həuniŋ] [mə'ʃi:n]搪磨机Hydraulic components [hai'drɔ:lik][kəm'pəunənt]液压元件Hydraulic power tools [hai'drɔ:lik]液压工具Hydraulic power units [hai'drɔ:lik]液压动力元件Hydraulic rotary cylinders['rəutəri] ['silində]液压回转缸Jigs [dʒiɡ]钻模Lapping machines ['læpiŋ] [mə'ʃi:n]精研机Lapping machines,centerless无心精研机Laser cutting ['leizə] ['kʌtiŋ]激光切割Laser cutting for SMT stencil['stensl, -sil]激光钢板切割机Lathe bench ['leizə] [bentʃ]车床工作台Lathes,automatic ['leizə] [,ɔ:tə'mætik]自动车床Lathes,heavy-duty ['leizə] [hevi:'du:ti:, -'dju:-]重型车床Lathes,high-speed ['leizə] [hai] [spi:d]高速车床Lathes,turret ['leizə] ['tʌrit]六角车床Lathes,vertical ['leizə] ['və:tikəl]立式车床Lubricants ['lu:brikənt]润滑液Lubrication Systems [,lu:bri'keiʃən] ['sɪstəm]润滑系统Lubricators ['lju:brikeitə]注油机Machining centers,general [mə'ʃi:niŋ] ['sentə] ['dʒ enərəl]通用加工中心Machining centers,horizontal [mə'ʃi:niŋ] ['sentə] [,hɔri'zɔntl]卧式加工中心Machining centers,horizontal & vertical [mə'ʃi:niŋ] ['sentə] [,hɔri'zɔntl] ['və:tikəl]卧式及立式加工中心Machining centers,vertical [mə'ʃi:niŋ] ['sentə] ['və:tikəl]立式加工中心Machining centers,vertical double-column type [mə'ʃi:niŋ] ['sentə] ['və:tikəl] ['dʌbl] ['kɔləm] [taip]立式双柱加工中心Magnetic tools [mæɡ'netik] [tu:l]磁性工具Manifolds ['mænifəuld]集合管Milling heads ['miliŋ] [hed]铣头Milling machines ['miliŋ] [mə'ʃi:n]铣床Milling machines,bed type ['miliŋ] [mə'ʃi:n] [taip]床身式铣床Milling machines,dupli cating ['miliŋ] [mə'ʃi:n] ['dju:plikeitiŋ]仿形铣床Milling machines,horizontal ['miliŋ] [mə'ʃi:n] [,hɔri'z ɔntl]卧式铣床Milling machines,turret vertical ['miliŋ] [mə'ʃi:n] ['tʌ rit] ['və:tikəl]六角立式铣床Milling machines,universal ['miliŋ] [mə'ʃi:n] [,ju:ni'və:səl]万能铣床Milling machines,vertical ['miliŋ] [mə'ʃi:n] ['və:tikəl]立式铣床Milling machines,vertical & horizontal ['miliŋ] [mə'ʃ i:n] ['və:tikəl] [,hɔri'zɔntl]立式及卧式铣床Mold & die components [məuld] [dai] [kəm'pəunənt] 模具单元Mold changing systems [məuld] ['tʃeindʒiŋ] ['sɪstəm] 换模系统Mold core [məuld] [kɔ:]模芯Mold heaters/chillers [məuld] ['hi:tə] ['tʃilə]模具加热器/冷却器Mold polishing/texturing [məuld] ['pɔliʃiŋ] ['tekstʃəriŋ]模具打磨/磨纹Mold repair [məuld] [ri'pɛə]模具维修Molds [məuld]模具Nail making machines [neil] [mə'ʃi:n]造钉机Oil coolers [ɔil] ['ku:lə]油冷却器Overflow cutting machines for aluminium wheels ['əuvə'fləu] [mə'ʃi:n] [,ælju:'minjəm] [wi:l, hw-]铝轮冒口切断机P type PVC waterproof rolled sheet making plant 6 [taip] ['wɔ:təpru:f] [rəuld] [ʃi:t] [plɑ:nt] PPVC高分子防水PCB fine piecing systems [fain] [pi:s] ['sɪstəm]( PCB =Printed -circuit Board [bɔ:d]印刷电路板)印刷电器板油压冲孔脱料系统Pipe & tube making machines [paip] [mə'ʃi:n] ['tju:b] [mə'ʃi:n]管筒制造机Planing machines [plæniŋ] [mə'ʃi:n]刨床Planing machines vertical [plæniŋ] [mə'ʃi:n] ['və:tikəl]立式刨床Pneumatic hydraulic clamps [nju(:)'mætik] [hai'dr ɔ:lik] [klæmp]气油压虎钳Pneumatic power tools [nju(:)'mætik] ['pauə] [tu:l]气动工具Powder metallurgic forming machines ['paudə] [,metə'lə:dʒik] ['fɔ:miŋ] [mə'ʃi:n]粉末冶金成型机Presses,cold forging [pres] ['fɔ:dʒiŋ]冷锻冲压机presses,crank [pres] [kræŋk]曲柄压力机Presses,eccentric [pres] [ik'sentrik]离心压力机Presses,forging [pres] ['fɔ:dʒiŋ]锻压机Presses,hydraulic [pres]液压冲床Presses,knuckle joint [pres]肘杆式压力机Presses,pneumatic [pres] [hai'drɔ:lik]气动冲床Presses,servo [pres] ['sə:vəu]伺服冲床Presses,transfer [pres] [træns'fə:]自动压力机Pressing dies [presiŋ] ['daii:z]压模Punch formers [pʌntʃ] ['fɔ:mə]冲子研磨器Quick die change systems [kwik] [dai] [tʃeindʒ] ['sɪ stəm]速换模系统Quick mold change systems [kwik] [məuld] [tʃeindʒ]['sɪstəm]快速换模系统Reverberatory furnaces [ri'və:bərətəri] ['fə:nis]反射炉Rollers ['rəulə]滚筒Rolling machines ['rəuliŋ] [mə'ʃi:n]辗压机Rotary tables ['rəutəri] ['teibl]转台Sawing machines ['sɔ:iŋ] [mə'ʃi:n]锯床Sawing machines,band ['sɔ:iŋ] [mə'ʃi:n] [bænd]带锯床Saws,band [sɔ:] [bænd]带锯Saws,hack [sɔ:] [hæk]弓锯Saws,horizontal band [sɔ:] [,hɔri'zɔntl] [bænd]卧式带锯Saws,vertical band [sɔ:] ['və:tikəl] [bænd]立式带锯shafts [ʃɑ:ft]轴Shapers ['ʃeipə]牛头刨床Shearing machines ['ʃiəriŋ] [mə'ʃi:n]剪切机Sheet metal forming machines [ʃi:t] ['metl] ['fɔ:miŋ] [mə'ʃi:n]金属板成型机Sheet metal working machines [ʃi:t] ['metl] [mə'ʃi:n]金属板加工机Slotting machines ['slɔtiŋ] [mə'ʃi:n]插床spindles ['spindl]主轴Stamping parts ['stæmpiŋ] [pɑ:t]冲压机Straightening machines ['streitniŋ] [mə'ʃi:n]矫直机Switches & buttons [switʃ] ['bʌtn]开关及按钮Tapping machines ['tæpiŋ] [mə'ʃi:n]攻螺丝机Transmitted chains [trænz'mit] [tʃein]传动链Tube bending machines ['tju:b] ['bendiŋ] [mə'ʃi:n]弯管机Vertical hydraulic broaching machine ['və:tikəl] [hai'drɔ:lik] ['brəutʃiŋ] [mə'ʃi:n]立式油压拉床Vises [vais]虎钳Vises,tool-maker [vais][ 'tu:l,meɪkə]精密平口钳Wheel dressers [wi:l, hw-] ['dresə]砂轮修整器Woven-Cutting machines ['wəuvən]织麦激光切割机Wrenches [rentʃ]扳手螺丝词汇的中英文对照六角盖头螺帽HEX CAP NUTS (HEX= hexagon ['heksəɡən] 六角形; 六边形) [kæp] [nʌts]六角锯齿螺帽HEX SERRATED NUTS (HEX= hexagon ['heksəɡən] 六角形; 六边形) [se'reitid [nʌts] 六角轮缘螺帽HEX FLANGE NUTS (HEX= hexagon ['heksəɡən] 六角形; 六边形) [flændʒ] [nʌts]高脚螺帽HEX COUPLING NUTS(HIGH NUTS) (HEX= hexagon['heksəɡən] 六角形; 六边形) ['kʌpliŋ] [nʌts] [hai]圆螺帽ROUND NUTS [raund] [nʌts]四角螺帽SQUARE NUTS HEAVY HEX NUTS [skwɛə] [n ʌts] [ 'hevi] (HEX= hexagon ['heksəɡən] 六角形; 六边形)不锈钢六角螺帽 STAINLESS STEEL HEX NUTS ['steinlis] [sti:l] (HEX= hexagon ['heks əɡən] 六角形; 六边形) [n ʌts] 不锈钢尼龙嵌入螺帽 STAINLESS STEEL NYLON INSERT LOCK NUTS ['steinlis] [sti:l] ['nail ən] [in's ə:t] [l ɔk] [n ʌts] 普通六角螺帽 HEX NUTS (HEX= hexagon ['heks əɡən] 六角形; 六边形) [n ʌts]六角重型螺帽 HEAVY HEX NUTS [ 'hevi]['heks əɡən][n ʌts]薄型螺帽 HEX JAM NUTS ['heks əɡən][d ʒæm] [n ʌts]尼龙嵌入防松螺帽NYLON INSERT LOCK NUTS ['nail ən][in's ə:t] [l ɔk] [n ʌts]机械螺丝用六角螺帽 HEX MACHINE SCREW NUT['heks əɡən] [m ə'ʃi:n] 7 [skru:] [n ʌt]机械工具英语 机械工具 spanner 扳子 (美作:wrench) ['spæn ə] [rent ʃ]double-ended spanner ['spæn ə]双头扳子adjustable spanner, monkey wrench [ə'd ʒʌst əbl] ['spæn ə]['m ʌŋki] [rent ʃ]活扳子,活络扳手 box spanner 管钳子 (美作:socket wrench) [b ɔks] ['spæn ə]['s ɔkit] [rent ʃ]calipers ['kælip ə]卡规pincers, tongs ['pins əz] [t ɔŋz]夹钳shears [ʃi əz]剪子 hacksaw ['hæks ɔ:]钢锯wire cutters ['wai ə] ['k ʌt ə]剪线钳 multipurposepliers,universal pliers ['m ʌlti'p ə:p əs] ['plai ə] [,ju:ni'v ə:s əl] ['plai əz]万能手钳 adjustable pliers [ə'd ʒʌst əbl] ['plai əz]可调手钳punch [p ʌnt ʃ]冲子drill [dril]钻chuck [t ʃʌk]卡盘scraper ['skreip ə]三角刮刀 reamer ['ri:m ə]扩孔钻calliper gauge ['kælip ə] [ɡedʒ]孔径规 rivet ['rivit]铆钉 nut [n ʌt]螺母 locknut ['l ɔkn ʌt]自锁螺母,防松螺母bolt [b əult]螺栓pin, peg, dowel [pin] [pe ɡ] ['dauəl]销钉washer ['w ɔʃə]垫圈 staple ['steipl]U 形钉 oil can 油壶 jack 工作服grease gun [ɡri:s]注油枪机械加工抛光 polishing ['p ɔli ʃiŋ]安装 to assemble [ə'sembl] 衬套 bushing ['bu ʃiŋ] 外贸常用机械英语大全 Assembly line [ə'sembl]组装线 Layout ['lei,aut]布置图 Conveyer [k ən'vei]流水线物料板 Rivet table ['rivit]拉钉机 Rivet gun ['rivit]拉钉枪 Screw driver 起子 Pneumatic screw driver [nju(:)'mætik]气动起子 worktable ['w ə:kteibl]工作桌OOBA 开箱检查fit together [tə'ɡeðə]组装在一起fasten ['fɑ:sn]锁紧(螺丝)ixture ['fikstʃə]夹具(治具)pallet ['pælit]栈板bar code [bɑ:] [kəud]条码bar code scanner [bɑ:] [kəud] ['skænə]条码扫描器fuse together [fju:z] [tə'ɡeðə]熔合fuse machine [fju:z] [mə'ʃi:n]热熔机repair[ri'pɛə]修理operator['ɔpəreitə]作业员QC [=Quality Control ['kwɔliti] [kən'trol]质量控制]品管supervisor ['sju:pəvaizə]课长ME [=Mechanical Engineer机械工程师]制造工程师MT 制造生技cosmetic inspect [kɔz'metik] [in'spekt]外观检查inner parts inspect ['inə] [in'spekt]内部检查thumb screw [θʌm]大头螺丝lbs inch [intʃ]镑、英寸EMI gasket ['ɡæskit]导电条front plate [frʌnt] [pleit]前板rear plate [riə] [pleit]后板chassis ['ʃæsi]基座bezel panel ['bezəl] ['pænl]面板power button ['pauə] ['bʌtn]电源按键reset button ['ri:set] ['bʌtn]重置键Hi-pot test of SPS [test]高源高压测试Voltage switch of SPS ['vəultidʒ] [switʃ]电源电压接拉键sheet metal parts [ʃi:t]冲件plastic parts ['plæstik, plɑ:stik]塑胶件SOP [=Standard Operating Procedure 标准操作程序] 制造作业程序material check list [mə'tiəriəl]物料检查表work cell [wə:k] [sel]工作间trolley ['trɔli]台车carton ['kɑ:tən]纸箱sub-line ['sʌblain]支线left fork [fɔ:k]叉车personnel resource department [,pə:sə'nel] [ri'sɔ:s] [di'pɑ:tmənt]人力资源部production department [prə'dʌkʃən]生产部门planning department ['plænɪŋ] [di'pɑ:tmənt]企划部QC Section ['sekʃən]品管科stamping factory ['stæmpiŋ] ['fæktəri]冲压厂painting factory ['peintiŋ]烤漆厂molding factory ['məuldiŋ] ['fæktəri]成型厂common equipment ['kɔmən] [i'kwipmənt]常用设备uncoiler and straightener [ʌn'kɔilə] ['streitənə]整平机punching machine [pʌntʃiŋ] [mə'ʃi:n]冲床robot ['rəubɔt, 'rɔbət]机械手hydraulic machine [hai'drɔ:lik]油压机lathe [leið]车床planer |plein|刨床miller ['milə]铣床grinder ['ɡraində]磨床linear cutting ['lini ə] ['k ʌtiŋ]线切割electrical sparkle [i'lektrik əl] ['sp ɑ:kl]电火花welder ['weld ə]电焊机staker=reviting machine ['steik ə]铆合机position [p ə'zi ʃən 职务president ['prezid ənt]董事长general manager ['d ʒen ər əl] ['mænid ʒə]总经理special assistant manager ['spe ʃəl] [ə's ɪst ənt] ['mænid ʒə]特助 factory director ['fækt əri] [di'rekt ə, dai'rekt ə]厂长department director[di'p ɑ:tmənt] [di'rektə, dai'rektə] 部长deputy manager | =vice manager 副理 section supervisor 课长 ['depjuti] ['mænid ʒə] ['sju:p əvaiz ə] deputy section supervisor =vice section supe risor['depjuti] ['sek ʃən] ['sju:p əvaiz ə]副课长group leader/supervisor['sju:p əvaiz ə]组长line supervisor['sju:p əvaiz ə]线长assistant manager 助理to move, to carry, to handle ['hændl]搬运be put in storage['st ɔrid ʒ]入库pack packing 包装to apply oil [ə'plai]擦油to file burr [fail] [b ə:]锉毛刺final inspection ['fain əl] [in'spek ʃən]终检to connect material [k ə'nekt] [m ə'ti əri əl]接料to reverse material [ri'v ə:s] [m ə'ti əri əl]翻料wet station ['stei ʃən]沾湿台cleaning cloth ['kli:niŋ] [klɔ(:)θ]抹布 to load material [l əud] [m ə'ti əri əl]上料 to unload material['ʌn'l əud] [m ə'ti əri əl]卸料 to return material/stock to [ri't ə:n] [m ə'ti əri əl] [st ɔk] 退料 scraped [skreipid]报废 scrape [skreip]v 刮;削 deficient purchase[di'fi ʃənt] ['p ə:t ʃəs]来料不良 manufacture procedure[,mænju'fækt ʃə] [pr ə'si:d ʒə]制程 deficient manufacturing procedure[di'fi ʃənt] [,mænju'fækt ʃə] [pr ə'si:d ʒə]制程不良 oxidation [ɔksi'dei ʃən]氧化 scratch[skræt ʃ]刮伤 dents['dents]压痕defective upsiding down[di'fektiv] ['ʌpsaidiŋ]抽芽不良 defective to staking[di'fektiv] ['steikiŋ]铆合不良 embedded lump[em'bedid] [l ʌmp]镶块 feeding is not in place['fi:diŋ] [pleis]送料不到位 stamping-missing ['stæmpiŋ] ['misiŋ]漏冲 production capacity [pr ə'd ʌk ʃən] [k ə'pæsiti]生产力 education and training [,edju(:)'kei ʃən] ['treiniŋ]教育培训 proposal improvement[pr ə'p əuz əl] [im'pru:vm ənt]提案改善 spare parts=buffer['b ʌf ə]备件 forklift['f ɔ:klift]叉车 trailer=long vehicle ['treil ə] ['vi:ikl]拖板车 外贸常用机械英语大全(续) compound die['k ɔmpaund] [dai]合模 die locker [dai] ['l ɔk ə]锁模器。

机械用语英文Aabrasion n.磨料,研磨材料,磨蚀剂,a.磨损的,磨蚀的abrasive belt n.砂带abrasive belt grinding n.砂带磨削,用研磨带磨光abrasive cut-off machine n.砂轮切断机abrasive dressing wheel n.砂轮修整轮abrasive grain n.磨料粒度abrasive grit n.研磨用磨料,铁粒abrasive lapping wheel n.磨料研磨轮accuracy of position n.位置精度accuracy to shape n.形状精度active cutting edge n.主切削刃adapter flange n.连接器法兰盘adjointing flanks n.共軛齿廓align n.找中(心),找正,对中,对准,找平,调直,校直,调angle milling cutter n.角铣刀angular grinding n.斜面磨削,斜磨法angular milling n.斜面铣削angular plunge grinding n.斜向切入磨削angular turning n.斜面车削arbour n.刀杆,心轴,柄轴,轴,辊轴attachment n.附件,附件机构,联结,固接,联结法automatic bar machine n.棒料自动车床automatic boring machine n.自动镗床automatic copying lathe n.自动仿形车床automatic double-head milling machine n.自动双轴铣床automatic lathe n.自动车床automatic turret lathe n.自动转塔车床整,调准Bbelt grinding machine n.砂带磨床bench lathe n.台式车床bevel n.斜角，斜面，倾斜，斜切，斜角规，万能角尺，圆锥的，倾斜的，斜边，伞齿轮，锥齿轮bevel gear cutting machine n.锥齿轮切削机床bevel gear tooth system n.锥齿轮系，锥齿轮传动系统borehole n.镗孔，镗出的孔，钻眼boring n.镗孔，钻孔，穿孔boring fixture n.镗孔夹具boring machine n.镗床boring tool n.镗刀boring,drilling and milling machine n.镗铣床broaching machine n.拉床，铰孔机，剥孔机broaching tool n.拉刀broad finishing tool n.宽刃精切刀，宽刃精车刀，宽刃光切刀C Calibrate vt.校准［正］，刻度，分度，检查［验］，定标，标定,使标准化，使符合标准cam contour grinder n.凸轮仿形磨床carbide tip n.硬质合金刀片contact pattern n.靠模continuous chip n.连续切屑continuous spiral chip n.连续螺旋切屑contour n.轮廓，外形，外貌，轮廓线，回路，网路，电路，等高线，carbide turning tool n.硬质合金车刀carbide-tipped tool n.硬质合金刀具cast iron machining n.铸铁加工，铸铁切削加工centerless cylindrical grinder n.无心外圆磨床ceramic cutting tool n.金属陶瓷刀具chamfer n.;vt.倒角，倒棱chamfered cutting edge n.倒角刀刃champ v.焦急champing fixture n.快换夹具champing jaw n.快换卡爪chaser n.螺纹梳刀，梳刀盘，板牙chatter vi.;n.振动，振荡，震颤，刀振cherry n.;a.樱桃，鲜红的，樱桃木制的chip n.切屑，铁屑，刀片，刀头，片，薄片，芯片，基片线，轮廓等高距a.仿形的，靠模的contour grinding n.仿形磨削，成形磨削contour milling n.成形铣削，外形铣削，等高走刀曲面仿形法convex milling attachment n.凸面铣削附件convex turning attachment n.中凸车削附件，凸面车削附件coolant lubricant n.冷却润滑剂coolant lubricant emulsion n.冷却润滑乳液［剂］copy n.样板，仿形，靠模工作法，拷贝复制品，v.复制,模仿,抄录copy grinding n.仿形磨床copy-mill n.仿形铣copying turret lathe n.仿形转塔车床corner n.角,弯［管］头,弯管counterbore n.埋头孔,沉孔,锥口孔,平底扩孔钻,平底锪钻,n.;vt.孔，锪孔，镗孔，镗阶梯孔crankshaft grinding machine n.曲轴磨床chip breaker groove radius n.断屑槽底半径，卷屑槽底半径chip clearance n.切屑间隙chip cross-sectional area n.切屑横截面面积chip curl n.螺旋形切屑chip flow n.切屑流chip formation n.切屑形成chip removing process n.去毛刺加工chip variable n.切屑变量chuck n.卡盘，夹盘，卡头，［电磁］吸盘，vt.固定，装卡，夹紧，卡住chucker n.卡盘车床，卡角车床circular drillling machine n.圆工作台钻床circular path n.环路，圆轨迹circular pitch measurement n.周节测量crankshaft turning lathe n.曲轴车床creep feed grinding n.缓进给磨削cross milling n.横向铣削curly chip n.卷状切屑，螺旋形切屑，切屑螺旋cut v.;n.切削［割］，口，片，断，断开，削减，减少，断面，剖面交，凹槽cut off n.切断［开，去］，关闭，停车，停止，断开装置，断流器，截止，截流cut teeeth n.铣齿cut-off grinding n.砂轮截断，砂轮切割cutter n.刀具，切削工具，截断器，切断器，切断机cutting n.切削，切片，切割，切屑，金属屑，截槽cutting edge profile n.切削刃轮廓［外形，断面］，切削刃角度cutting force n.切削力cutting lip n.切削刃，刀刃，钻唇，钻刃circumference n.圆周，周线，周界，周围，四周，范围close-grained a.细颗粒的coeffecient of tool thrust n.刀具推力系数coil chip n.卷状切屑cold circular saw n.冷圆锯cold saw n.冷锯column drilling machine n.圆［方］柱立式钻床combined drill and milling cutter n.复合钻铣床complete traverse grinding n.横进给磨削，切入磨削computer-controlled machine n.计算机控制机床，数控机床cutting operation n.切削加工，切削操作，切削作业cutting rate n.切削效率，切削速率cutting tool n.刀具，切削工具，刃具cycle n.周期，周，循环，一个操作过程，轮转，自行车cylindrical grinder n.外圆磨床Ddamage n.;vt.损坏［害，伤，耗，失］，破坏，事故，故障，伤害，危害deep-hole drilling n.深孔钻削distance n.距离，间隔［隙］，长度，vt.隔开double-column planer-miller n.双柱龙门铣床dress v.修饰，修整，平整，整理，清理，装饰，调制，准备，打磨，deep-hole milling n.深孔铣削design n.设计，计算，计划，方案，设计书，图纸die-sinking n.凹模dimension n.尺寸，尺度，维度，量纲，因次direction of the feed motion n.进给方向，进刀方向discontinuous chip n.间断切屑压平，轿直，清洗，清理，分级drilling n.钻头，钻床，穿孔器，凿岩机，v.钻孔，打孔，钻井，钻drilling machine n.钻床，钻机，钻孔机，打眼机drilling tool n.钻孔［削，井，眼］工具Eedge point n.刀口，刀刃efficiency n.效率，效能，性能，功率，产量，实力，经济性，有［功，实］效end mill n.立铣刀external grinding n.外圆磨削Fface n.表面，外观，工作面，表盘，屏，幕v.面向，朝向，表面加工，把表面弄平face grinding machine n.平面磨床face milling machine n.端面磨床finish v.;n.精加工，抛光，修整，表面粗糙度，完工，最后加工，最段，涂层，涂料finish-cutting n.精加工，最终切削fixture n.夹具，夹紧装置，配件，零件，定位器，支架feed force n.进给力feed motion n.进给运动fine adjustment n.精调，细调，微调fine boring n.精密镗孔form n.型式，类型，摸板，模型，形成，产生，成形，表格v.形［构］成，产生，作出，成形，造型form-turn n.成形车削free-cutting n.自由切削，无支承切削，高速切削Ggap n.间隔，间隙，距离，范围，区间，缺口，开口火花隙，vt.使产生裂缝vi.豁开gear cutting machine n.齿轮加工机床，切齿机gear generating grinder n.磨齿机gear hob n.齿轮滚刀grinding cutter n.磨具grinding force n.磨削力grinding machine n.磨床grinding wheel diameter n.砂轮直径grinding wheel width n.砂轮宽度groove n.槽，切口，排屑槽，空心槽，坡口，vt.切［开，铣］槽groove milling n.铣槽Hheadstock spindle n.床头箱主轴，主轴箱主轴，头架轴helical tooth system n.螺旋齿轮传动装置hobbing machine n.滚齿机，螺旋铣床，挤压制模压力机，反应阴模hole n.孔，洞，坑，槽，空穴，孔道，管道，v.钻［穿，冲，开］孔high precision lathe n.高精度车床high-speed n.高速high-speed machining n.高速加工hob n.齿轮滚刀，滚刀，螺旋铣刀，v.滚铣，滚齿，滚削horsepower n.马力洞hone n.vt.磨石，油石，珩磨头，磨孔器，珩磨，honing machine n.珩磨机，珩床，搪磨床，磨孔机，磨气缸机I inclination n.倾斜，斜度，倾角，斜角［坡］，弯曲，偏［差，角］转increment n.增量，增加，增［大］长indexing table automatic n.自动分度工作台infeed grinding n.切入式磨削installation n.装置，设备，台，站，安装，设置internal grinding n.内圆磨削involute hob n.渐开线滚刀Jjig boring machine n.坐标镗床keyway cutting n.键槽切削加工knurling tool n.滚花刀具，压花刀具，滚花刀Llaedscrew machine n.丝杠加工机床lap grinding n.研磨lapping n.研磨，抛光，精研，搭接，擦准lathe n.车床lathe dog n.车床轧头，卡箍，鸡心夹头，离心夹头，制动爪，车床挡块lathe tool n.车刀level n.水平，水准，水平线，水平仪，水准仪，电平，能级，程度，a.水平的，相等的，均匀的，平稳的loading time n.装载料时间，荷重时间，充填时间，充气时间lock n.锁，栓，闸，闭锁装置，锁型，同步，牵引，v.闭锁，关闭，固定，定位，制动刹住longitudinal grinding n.纵磨low capacity machine n.小功率机床［机器］Mmachine axis n.机床中心线machine table n.机床工作台machine tool n.机床，工作母机machining n.机械加工，切削加工machining(or cutting)variable n.加工（或切削）变量metal-cutting technology n.金属切削工艺学，金属切削工艺［技术metal-cutting tool n.金属切削刀具，金属切削工具micrometer adjustment n.微调milling n.铣削，磨碎，磨整，选矿milling feed n.铣削进给，铣削走刀量，铣削走刀机构milling machine n.铣床machining allowance n.机械加工余量machining cycle n.加工循环machining of metals n.金属切削加工，金属加工magazine automatic n.自动化仓库，自动化料斗，自动存贮送料装置manufacture n.制造者，生产者，厂商，产品，制造material removing rate n.材料去除率metal cutting n.金属切削milling spindle n.铣床主轴milling tool n.铣削刀具，铣削工具mount v.固定，安装，装配，装置，架设，n.固定件，支架，座，装机构mounting n.安装，装配，固定，机架，框架，装置mounting fixture n.安装夹具，固定夹具NNose n.鼻子，端，前端，凸头，刀尖，机头，突出部分，伸出部分number of revolutions n.转数numerical control n.数字控制numerically controlled lathe n.数控车床Ooblique grinding n.斜切式磨床operate v.操纵，控制，运行，工作，动作，运算oscillating type abrasive cutting machine n.摆动式砂轮切割机oscillation n.振动，振荡，摆动，颤振，振幅operating cycle n.工作循环operation n.运转，操作，控制，工作，作业，运算，计算operational instruction n.操作说明书，操作说明operational safety n.操作安全性，使用可靠性out-cut milling n.切口铣削oxide ceramics n.氧化物陶瓷oxide-ceramic cutting tool n.陶瓷刀具Pperformance n.实行，执行，完成，特性，性能，成品，制作品，行为，动作，生产率，效率peripheral grinding n.圆周磨削peripheral speed n.圆周速度，周速，边缘速度perpendicular a.垂直的，正交的，成直角的n.垂直，正交，竖直，垂线，垂直面physical entity n.实体，实物pitch n.齿距，节距，铆间距，螺距，极距，辊距，坡度，高跨比，俯仰角plunge-cut thread grinder n.切入式螺纹磨床plunge-grinding n.切入式磨削point n.点，尖端，刀尖，针尖，指针，交点，要点，论点，特点v.面向，瞄准，对准，表明，弄尖，强调power n.功率，效率，能［容，力］量，动力，电源，能源v.驱［拖发］动，给...以动力power hacksaw n.机动弓锯［钢锯］precision boring n.精镗precision boring machine n.精密镗床pitch circle n.节圆plain (or cylindrical)milling machine n.普通（或圆柱形）铣床plain grinding n.平面磨削plain turning n.平面车床plane n.平面，面，投影，刨，水平，程度，阶段，飞机a.平的v.弄平，整平，刨，飞行plane milling n.平面铣削plane-mill n.平面铣刀，平面铣床plunge mill n.模向进给滚轧机plunge-cut n.切入式磨削，横向进给磨削，全面进刀法，全面进给法precision machining n.精密机械加工pressure angle n.压力角primary cutting edge n.主切削刃principal feed motion n.主进给运动，主进刀运动production method s n.生产方法[式] profile n.轮廓，形面，剖面，侧面图，分布图。