工程建筑电气文献与外文翻译

建筑电气电气工程设计包括两个主要的设计方面。

主要是一部分的电能的转换及分配和电力的供配、照明系统、防雷接地系统。

一般来说,建筑主要的变化包括:高压和低压配电系统、变压器、备用电源系统。

电力系统包括配电和控制，室内和室外照明系统包括所有类型的照明，防雷系统包括入侵波防护、闪电传感器、接地、等电位连接和局部等电位连接等。

辅助等电位连接等。

在短短的20年里,系统在技术和产品的面貌发生了翻天覆地的变化。

许多的设计理念也发生了巨大的变化。

开关设备如高压系统的第一个断路器油断路器，后来油断路器的逐步发展,不仅规模大,但是一般都包含油物质。

由于开关设备尺寸较大,我们还必须建立独立的设备房间,占据了大量的建筑面积。

现在真空断路器和六氟化硫断路器,不仅体积小,而且短路容量大，外壳尺寸远小于原来的橱柜，并且断路器没有任何油,防火性能大大提高。

而且断路器和其他低压设备在一个房间里,这样即节省空间又方便管理。

过去大容量的低压断路器,短路电流容量逐渐变大,规模也逐渐变小,而且更加稳定,使系统运行更加安全可靠,为设计带来了方便。

向着智能化低压断路器方向发展,断路器各种参数可以通过总线工业控制,信号直接传输到计算机。

干式变压器的出现,对建筑电气设计带来了极大的方便,因为没有变压器油泄漏和火灾的可能性,以便它可以很容易地安装在建筑本身,甚至直接到负荷中心。

它还消除变压器对油的需求限制,构建大容量设备时可以使用干式变压器。

在实际工程设计中曾应用四个台湾2500kVA干式变压器。

在使用紧急发电机方面,从性能和尺寸的角度来看,比过去进步很多。

除了使用柴油发电机；应急照明使用EPS备用电源；中断供电在一个毫秒以内的设备,可以使用UPS。

电力设备的控制从单一元件的控制到控制继电器控制变化。

除了更好的性能的各种组件的规模较小,也降低控制箱的规模。

由于数字技术更多的运用于控制能达到最佳的控制状态来控制设备。

进一步提高了节能的效果。

照明系统从过去单一光源、灯具和低效率的状态向更广泛的前景发展。

建筑电气外文文献Increasing an individual’s quality of life via theirintelligent homeThe hypothesis of this project is: can an individual’s quality of life be increased by integrating ?intelligent technology? into theirhome environment. This hypothesis is very broad, and hence the researchers will investigate it with regard to various, potentiallyover-lapping, sub-sections of the population. In particular, the projectwill focus on sub-sections with health-care needs, because it isbelieved that these sub-sections will receive the greatest benefit fromthis enhanced approach to housing. Two research questions flow from this hypothesis: what are the health-care issues that could be improved via?intelligenthousing?, and what are the technological issues needing to be solvedto allow ?intelligent housing? to be constructed? While a small numberofinitiatives exist, outside Canada, which claim to investigate thisarea, none has the global vision of this area. Work tends to be in smallareas with only a limited idea of how the individual pieces contributetowards a greater goal. This project has a very strong sense of what itis trying to attempt, and believes that without this global directionthe other initiatives will fail to address the large important issuesdescribed within various parts of this proposal, and that with thecorrect global direction the sum of the parts will produce much greater rewards than the individual components. This new field has manyparallels with the fieldof business process engineering, where many products fail due toonly considering a sub-set of the issues, typically the technologysubset. Successful projects and implementations only started flow when people started to realize that a holistic approach was essential. Thisholis tic requirement also applies to the field of ?smart housing?; if we genuinelywant it to have benefit to the community rather than justtechnological interest. Having said this, much of the work outlinedbelow is extremely important and contains a great deal of novelty within their individual topics.Health-Care and Supportive housing:To date, there has been little coordinated research on how ?smarthouse? technologies can assist frail seniors in remaining at home,and/or reduce the costs experienced by their informal caregivers. Thus,the purpose of the proposed research is to determine the usefulness of a variety of residential technologies in helping seniors maintain their independence and in helping caregivers sustain their caring activities.The overall design of the research is to focus on two groups of seniors. The first is seniors who are being discharged from an acutecare setting with the potential for reduced ability to remainindependent. An example is seniors who have had hip replacement surgery.This group may benefit from technologies that would help them becomeadapted to their reduced mobility. The second is seniors who have achronic health problem suchas dementia and who are receiving assistance from an informalcaregiver living at a distance. Informal caregivers living at a distancefrom the cared-for senior are at high risk of caregiver burnout.Monitoring the cared-for senior for health and safety is one of theimportant tasks done by such caregivers. Devices such as floor sensors(to determine whether the senior has fallen) and access controls toensure safety from intruders or to indicate elopement by a senior withdementia could reduce caregiver time spent commuting to monitor thesenior.For both samples, trials would consist of extended periods ofresidence within the ‘smart house’. Samples of seniors beingdischarged from acute care would be recruited from acute care hospitals.Samples of seniors being cared for by informal caregivers at a distancecould be recruited through dementia diagnosis clinics or through requestfrom caregivers for respite.Limited amounts of clinical and health service research has beenconducted upon seniors (with complex health problems) in controlled environments such as that represented by the ?sm art house?. For example, it is known that night vision of the aged is poor but there is verylittle information regarding the optimum level of lighting afterwakening or for night activities. Falling is a major issue for olderpersons; and it results in injuries, disabilities and additional healthcare costs. For those with dementing illnesses, safety is the key issue during performanceof the activities of daily living (ADL). It is vital for us to beable to monitor where patients would fall during ADL. Patients and caregivers activities would be monitored and data will be collected inthe following conditions.Projects would concentrate on sub-populations, with a view to collecting scientific data about their conditions and the impact of technology upon their life styles. For example:-Persons with stable chronic disability following a stroke and their caregivers: to research optimum models, types and location of various sensors for such patients (these patients may have neglect, hemiplegia, aphasia and judgment problems); to research pattern of movements during the ambulation, use of wheel chairs or canes on various type of floor material; to research caregivers support through e-health technology; to monitor frequencies and location of the falls; to evaluate the value of smart appliances for stroke patients and caregivers; to evaluate information and communication technology set up for Tele-homecare; to evaluate technology interface for Tele-homecare staff and clients; to evaluate the most effective way of lighting the various part of thehouse; to modify or develop new technology to enhance comfort and convenience of stroke patients and caregivers; to evaluate the value of surveillance systems in assisting caregivers.- Persons with Alzheimer’s disease and their caregivers: to evaluate theeffect of smart house (unfamiliar environment) on their ability to conduct self-care with and without prompting; to evaluate their abilityto use unfamiliar equipment in the smart house; to evaluate and monitor perso ns with Alzheimer’s disease movement pattern; to evaluate and monitor falls or wandering; to evaluate the type and model of sensors to monitor patients; to evaluate the effect of wall color for patients andcare givers; to evaluate the value of proper lighting.Technology - Ubiquitous Computing:The ubiquitous computing infrastructure is viewed as the backbone of the ?intelligence? within the house. In common with all ubiquitous computing systems, the primary components with this system will be: the array of sensors, the communication infrastructure and the software control (based upon software agents) infrastructure. Again, it is considered essential that this topic is investigated holistically.Sensor design: The focus of research here will be development of (micro)-sensors and sensor arrays using smart materials, e.g. piezoelectric materials, magneto strictive materials and shape memory alloys (SMAs). In particular, SMAs are a class of smart materials thatare attractive candidates for sensing and actuating applicationsprimarily because of their extraordinarily high work output/volume ratio compared to other smart materials. SMAs undergo a solid-solid phase transformation when subjected to an appropriate regime of mechanical andthermal load, resulting in a macroscopic change in dimensions and shape; this change is recoverable by reversing the thermo mechanical loading and is known as a one-way shape memory effect. Due to this material feature, SMAs can be used as both a sensor and an actuator. A very recent development is an effort to incorporate SMAs in micro-electromechanical systems (MEMS) so that these materials can be used as integral parts of micro-sensors and actuators.MEMS are an area of activity where some of the technology is mature enough for possible commercial applications to emerge. Some examples are micro-chemical analyzers, humidity and pressure sensors, MEMS for flow control, synthetic jet actuators and optical MEMS (for the nextgeneration internet). Incorporating SMAs in MEMS is a relatively neweffort in the research community; to the best of our knowledge, only one group (Prof. Greg Carman, Mechanical Engineering, University of California, Los Angeles) has successfully demonstrated the dynamic properties of SMA-based MEMS. Here, the focus will be to harness the sensing and actuation capabilities of smart materials to design and fabricate useful and economically viable micro-sensors and actuators.Communications: Construction and use of an ?intelligent house?offersextensive opportunities to analyze and verify the operation ofwireless and wired home-based communication services. While some of these are already widely explored, many of the issues have receivedlittle or noattention. It is proposed to investigate the following issues: - Measurement of channel statistics in a residential environment: knowledge of the indoor wireless channel statistics is critical forenabling the design of efficient transmitters and receivers, as wellas determining appropriate levels of signal power, data transferrates,modulation techniques, and error control codes for the wirelesslinks.Interference, channel distortion, and spectral limitations thatarises as a result of equipment for the disabled (wheelchairs, IVstands, monitoring equipment, etc.) is of particular interest. -Design, analysis, and verification of enhanced antennas for indoor wireless communications. Indoor wireless communications present the need for compact and rugged antennas. New antenna designs, optimized for desired data rates, frequency of operation, and spatialrequirements, could be considered.- Verification and analysis of operation of indoor wireless networks:wireless networking standards for home automation have recently been commercialized. Integration of one or more of these systems into thesmart house would provide the opportunity to verify the operation ofthese systems, examine their limitations, and determine whether thestandards are over-designed to meet typical requirements. - Determination o f effective communications wiring plans for ?smart homes.?: there exist performance/cost tradeoffs regarding wired andwireless infrastructure. Measurement and analysis of variouswireless network configurations will allow for determination ofappropriate network designs.- Consideration of coordinating indoor communication systems with larger-scale communication systems: indoor wireless networks are local to the vicinity of the residence. There exist broader-scalenetworks, such as the cellular telephone network, fixed wirelessnetworks, and satellite-based communication networks. The viability and usefulness of compatibility between these services for thepurposes of health-care monitoring, the tracking of dementia patients,etc needs to be considered.Software Agents and their Engineering: An embedded-agent can be considered the equivalent of supplying a friendly expert with a product. Embedded-agents for Intelligent Buildings pose a number of challenges both at the level of the design methodology as well as the resulting detailed implementation. Projects in this area will include:- Architectures for large-scale agent systems for human inhabited environment: successful deployment of agent technology inresidential/extended care environments requires the design of new architectures for these systems. A suitable architecture should be simple and flexible to provide efficient agent operation in realtime.At the same time, it should be hierarchical and rigid to allowenforcement of rules and restrictions ensuring safety of the inhabitants of the building system. These contradictory requirements have to be resolved by designing a new architecture that will be sharedby all agents in the system.- Robust Decision and Control Structures for Learning Agents: to achieve life-long learning abilities, the agents need to be equippedwith powerful mechanisms for learning and adaptation. Isolated use of some traditional learning systems is not possible due to high-expected lifespan of these agents. We intend to develop hybrid learning systems combining several learning and representation techniques in an emergent fashion. Such systems will apply different approaches based on their own maturity and on the amount of change necessary to adapt to a new situation or learn new behaviors. To cope with high levels of non-determinism (from such sources as interaction with unpredictable human users), robust behaviors will be designed and implemented capable of dealing with different types of uncertainty (e.g. probabilistic andfuzzy uncertainty) using advanced techniques for sensory and data fusion, and inference mechanisms based on techniques of computational intelligence.- Automatic modeling of real-world objects, including individual householders: The problem s here are: ?the locating and extracting?of information essential for representation of personality andhabitsof an individual; development of systems that ?follow and adopt to?individual’s mood and behavior. The solutions, based on data miningand evolutionary techniques, will utilize: (1) clustering methods,classification tress and association discovery techniques for theclassification and partition of important relationships among differentattributes for various features belonging to an individual, this is anessential element in finding behavioral patterns of an individual; and(2) neuro-fuzzy and rule-based systems with learning and adaptation capabilities used to develop models of an individual’s characteristics, this is essential for estimation and predictionof potential activities and forward planning.- Investigation of framework characteristics for ubiquitouscomputing: Consider distributed and internet-based systems, whichperhaps have the most in common with ubiquitous computing, here again,the largest impact is not from specific software engineering processes,but is from available software frameworks or ‘toolkits’, which allow the rapidconstruction and deployment of many of the systems in these areas. Hence, it is proposed that the construction of the ubiquitous computing infrastructure for the ?smart house? should also be utilized as asoftware engineering study. Researchers would start by visiting thefew genuine ubiquitous computing systems in existence today, to try tobuild up an initial picture of the functionality of the framework.(This approach has obviously parallels with the approach of Gamma,Helm, Johnson and Vlissides deployed for their groundbreaking work on?design patterns?. Unfortunately, in comparison to their wo rk, the sample size here will be extremely small, and hence, additional workwill be required to produce reliable answers.) This initial frameworkwill subsequently be used as the basis of the smart house’s software system. Undoubtedly, this initial framework will substantiallyevolve during the construction of the system, as the requirements ofubiquitous computing environment unfold. It is believed that such close involvement in the construction of a system is a necessary component in producing a truly useful and reliable artifact. By the end of theconstruction phase, it is expected to produce a stable framework, whichcan demonstrate that a large number of essential characteristics (orpatterns) have been found for ubiquitous computing.- Validation and Verification (V&V) issues for ubiquitous computing:it is hoped that the house will provide a test-bed for investigatingvalidation and verification (V&V) issues for ubiquitous computing. Thehouse will be used as an assessment vehicle to determine which, if any,V&V techniques, tools or approaches are useful within this environment. Further, it is planned to make this trial facility available toresearchers worldwide to increase the use of this vehicle. In thelong-term, it is expected that the facilities offered by thisinfrastructure will evolve into an internationally recognized?benchmarking? site for V&V activities in ubiquitous computing.Other technological areas:The project also plans to investigate a number of additional areas,such as lighting systems, security systems, heating, ventilation and air conditioning, etc. For example, with regard to energy efficiency, theproject currently anticipates undertaking two studies:- The Determination of the effectiveness of insulating shutters:Exterior insulating shutters over time are not effective because ofsealing problems. Interior shutters are superior and could be usedto help reduce heat losses. However, their movement and positioning needs appropriate control to prevent window breakage due to thermal shock. The initiation of an opening or closing cycle would be basedon measured exterior light levels; current internal heating levels;current and expected use of the house by the current inhabitants,etc. - A comparison of energy generation alternatives: The energy use patterns can easily be monitored by instrumenting each appliance.Natural gas and electricity are natural choices for the main energysupply. The conversion of the chemical energy in the fuel to heatspace and warm water can be done by conventional means or by use ofa total energy system such as a Volvo Penta system. With this system,the fuel is used to power a small internal combustion engine, whichin turn drives a generator for electrical energy production. Waste heatfrom the coolant and the exhaust are used to heat water for domestic use and space heating. Excess electricity is fed back into the power grid or stored in batteries. At a future date, it is planned to substitute afuel cell for the total energy system allowing for a direct comparison of the performance of two advanced systems.。

24.437 电力电子正弦脉宽调制如图1所示，电压源逆变器的开关可以按要求打开和关闭。

用最简单的方法，顶部的开关打开，如果每个周期打开和关闭，则方波的波形结果只有一次。

但是如果改进谐波的数据则在个周期内可以实现多次打开关闭。

图1 简单的电压源逆变器 如图2所示，用最直接的执行方式，所期望的输出电压是通过比较预期的参考波形与高频率的三角载波(调制信号) 生成的，无论直流电压是正还是负，信号电压的输出只根据信号电压是否大于或小于载波波形，要注意的是，在此期间一个三角载波周期的平均电压即信号的振幅加到负载形成正比(假定不变)。

经过一段时间，三角载波的负荷是正比于幅值的信号，在这期间，由此产生的方波包含有在它低频元件所需波形的幅值，也具有较高频率分量在一个载波临近频率的幅值。

需要注意的是，由于PWM 使得总谐波不失真，均方根的平均交流电压波形幅值仍与直流电压相等。

谐波分量只是转移到了更高的平率范围，并由电感式交流系统自动过滤。

当正弦波调制信号的振幅为Am ，三角载波的振幅为Ac 时，它们的调制指数就是m=Am/ Ac 。

因此，控制调制指数控制着输出电压的幅值。

如图3所示，fc/fm=21 ，t=L/R=T/3，T 为基本周期，由于感性元件的存在，高频成分不能明显的传播到交流网络(或负载)，所以具有足够高的载波频率。

然而，由于具有较高的载波频率，从而导致在更多的功率损耗。

所以，在电力系统的应用中，通常认为使用2-15kHz 的开关频率最为合适。

此外，在三相系统中，建议使用)(,3N k k f f mc ∈=，使得三个波形对称。

图2 主要的脉宽调制图3 SPWM的fc/fm=48，L/R=T/3如图4所示，该过程是比较合适的，因为在该图中有三角载波，其中没有交集的载体作为信号周期。

然而，这种“超调”在一定量的范围内往往是允许获得更大的交流电压，使电压频谱呈现出差异。

需要注意的是，使用一个额外的比率形成一个反周期超过360°的对称波形。

1、 外文原文（复印件）A: Fundamentals of Single-chip MicrocomputerT h e sin gle -ch ip mi c ro co m p u t e r is t h e cu lm in at io n of b ot h t h e d e ve lo p me nt of t h e d ig ita l co m p u t e r a n d t h e i nte g rated c ircu it a rgu ab l y t h e to w mo st s ign if i cant i nve nt i o n s of t h e 20t h c e nt u ry [1].T h ese to w t yp e s of arch ite ct u re are fo u n d in s in gle -ch ip m i cro co m p u te r. S o m e e mp l oy t h e sp l it p ro gra m /d at a m e m o r y of t h e H a r va rd arch ite ct u re , s h o wn in -5A , ot h e rs fo l lo w t h e p h i lo so p hy, wid e l y ad a p ted fo r ge n e ral -p u rp o se co m p u te rs an d m i cro p ro ce ss o rs , of m a kin g n o l o g i ca l d i st in ct i o n b et we e n p ro gra m an d d ata m e m o r y as in t h e P rin c eto n a rch ite ct u re , sh o wn in -5A.In ge n e ra l te r m s a s in g le -ch ip m ic ro co m p u t e r is ch a ra cte r ized b y t h e in co r p o rat io n of all t h e u n its of a co mp u te r into a s in gle d e vi ce , as s h o w n in F i g3-5A-3.-5A-1A Harvard type-5A. A conventional Princeton computerProgrammemory Datamemory CPU Input& Output unitmemoryCPU Input& Output unitResetInterruptsPowerFig3-5A-3. Principal features of a microcomputerRead only memory (ROM).RO M is u su a l l y fo r t h e p e r m an e nt , n o n -vo lat i le sto rage of an ap p l i cat io n s p ro g ram .M a ny m i c ro co m p u te rs a n d m i cro co nt ro l le rs are inte n d ed fo r h i gh -vo lu m e ap p l i cat io n s a n d h e n ce t h e e co n o m i cal man u fa c t u re of t h e d e vi ces re q u ires t h at t h e co nt e nts of t h e p ro gra m me mo r y b e co mm i ed p e r m a n e nt l y d u r in g t h e m a n u fa ct u re of c h ip s . C lea rl y, t h i s imp l ies a r i go ro u s ap p ro a ch to ROM co d e d e ve lo p m e nt s in ce ch an ges can n o t b e mad e af te r m an u fa ct u re .T h i s d e ve l o p m e nt p ro ces s m ay i nvo l ve e mu l at i o n u sin g a so p h ist icated d e ve lo p m e nt syste m wit h a h ard wa re e mu l at i o n capab i l it y as we ll as t h e u s e of p o we rf u l sof t war e to o l s.So m e m an u fa ct u re rs p ro vi d e ad d it i o n a l ROM o p t io n s b y in clu d in g in t h e i r ran ge d e v ic es w it h (o r inte n d ed fo r u s e wit h ) u se r p ro g ram m a b le m e mo r y. T h e s im p lest of t h e se i s u su a l l y d e v i ce wh i ch can o p e rat e in a m i cro p ro ce s so r mo d e b y u s in g s o m e of t h e in p u t /o u t p u t l in es as an ad d res s a n d d ata b u s fo r a cc es sin g exte rn a l m e m o r y. T h is t yp e o f d e vi ce can b e h ave f u n ct i o n al l y as t h e s in gle ch ip m i cro co m p u t e r f ro m wh i ch it i s d e ri ved a lb e it wit h re st r icted I/O an d a m o d if ied exte rn a l c ircu it. T h e u s e of t h e se RO M le ss d e vi ces i s co mmo n e ve n in p ro d u ct io n circu i ts wh e re t h e vo lu m e d o e s n ot ju st if y t h e d e ve lo p m e nt co sts of cu sto m o n -ch ip ROM [2];t h e re ca n st i ll b e a si gn if i cant sav in g in I/O an d o t h e r ch ip s co m pared to a External Timing components System clock Timer/ Counter Serial I/O Prarallel I/O RAM ROMCPUco nve nt io n al m i c ro p ro ces so r b ased circ u it. M o re exa ct re p l a ce m e nt fo rRO M d e v ice s can b e o b tain ed in t h e fo rm of va ria nts w it h 'p i g g y-b a c k'E P ROM(E rasab le p ro gramm ab le ROM )s o cket s o r d e v ice s w it h E P ROMin stead of ROM 。

电气工程的外文文献(及翻译)文献一：Electric power consumption prediction model based on grey theory optimized by genetic algorithms本文介绍了一种基于混合灰色理论与遗传算法优化的电力消耗预测模型。

该模型使用时间序列数据来建立模型，并使用灰色理论来解决数据的不确定性问题。

通过遗传算法的优化，模型能够更好地预测电力消耗，并取得了优异的预测结果。

此模型可以在大规模电力网络中使用，并具有较高的可行性和可靠性。

文献二：Intelligent control for energy-efficient operation of electric motors本文研究了一种智能控制方法，用于电动机的节能运行。

该方法提供了一种更高效的控制策略，使电动机能够在不同负载条件下以较低的功率运行。

该智能控制使用模糊逻辑方法来确定最佳的控制参数，并使用遗传算法来优化参数。

实验结果表明，该智能控制方法可以显著降低电动机的能耗，节省电能。

文献三：Fault diagnosis system for power transformers based on dissolved gas analysis本文介绍了一种基于溶解气体分析的电力变压器故障诊断系统。

通过对变压器油中的气体样品进行分析，可以检测和诊断变压器内部存在的故障类型。

该系统使用人工神经网络模型来对气体分析数据进行处理和分类。

实验结果表明，该系统可以准确地检测和诊断变压器的故障，并有助于实现有效的维护和管理。

文献四：Power quality improvement using series active filter based on iterative learning control technique本文研究了一种基于迭代研究控制技术的串联有源滤波器用于电能质量改善的方法。

中文2795字第一部位译文部分变压器摘要：变压器是变电所的主要设备，功能是实现电网电压的等级变换，基本工作原理是电磁感应。

变配电所是实现电压等级变换和电能分配的场所。

对供电电源进行电压等级变换，应对电能进行重新分配的场所称为变电所。

建筑变电所是供配电系统的枢纽，供电电源由电网引到变电所，在变电所完成降压，电能分配等功能。

关键词:变电所；变压器；继电保护；1. 介绍要从远端发电厂送出电能，必须应用高压输电。

因为最终的负荷，在一些点高电压必须降低。

变压器能使电力系统各个部分运行在电压不同的等级。

本文我们讨论的原则和电力变压器的应用。

2. 双绕组变压器变压器的最简单形式包括两个磁通相互耦合的固定线圈。

两个线圈之所以相互耦合，是因为它们连接着共同的磁通。

在电力应用中，使用层式铁芯变压器(本文中提到的)。

变压器是高效率的，因为它没有旋转损失，因此在电压等级转换的过程中，能量损失比较少。

典型的效率范围在92到99%，上限值适用于大功率变压器。

从交流电源流入电流的一侧被称为变压器的一次侧绕组或者是原边。

它在铁圈中建立了磁通φ，它的幅值和方向都会发生周期性的变化。

磁通连接的第二个绕组被称为变压器的二次侧绕组或者是副边。

磁通是变化的；因此依据楞次定律，电磁感应在二次侧产生了电压。

变压器在原边接收电能的同时也在向副边所带的负荷输送电能。

这就是变压器的作用。

3. 变压器的工作原理当二次侧电路开路是，即使原边被施以正弦电压Vp ，也是没有能量转移的。

外加电压在一次侧绕组中产生一个小电流Iθ。

这个空载电流有两项功能：（1）在铁芯中产生电磁通，该磁通在零和±φm 之间做正弦变化，φm 是铁芯磁通的最大值；（2）它的一个分量说明了铁芯中的涡流和磁滞损耗。

这两种相关的损耗被称为铁芯损耗。

变压器空载电流Iθ一般大约只有满载电流的2%—5%。

因为在空载时，原边绕组中的铁芯相当于一个很大的电抗，空载电流的相位大约将滞后于原边电压相位90º。

Power supply system of high-rise building designAbstract: With the continuous development of city size, more and more high-rise buildings, therefore, high-rise building electrical design to the designers had to face. In this paper, an engineering example, describes the electrical design of high-rise buildings and some of the more typical issues of universal significance, combined with the actual practice of an engineering solution to the problem described.Key words: high-rise building; electrical design; distribution; load calculation1 Project OverviewThe commercial complex project, with a total construction area of 405570m2, on the ground floor area of 272330m2, underground construction area of 133240m2, the main height of 99m. Project components are: two office buildings, construction area is 70800m2, 28 layers, the standard story is 3.2m.2 Load Calculation1) Load characteristics: electric load, much larger than the "national civil engineering technical measures" Large 120W/m2 indicators, especially in the electricity load more food, and different types of food and beverage catering different cultural backgrounds also high.2) the uncertainty of a large load, because the commercial real estate rents are often based on market demand, and constantly adjust the nature of the shops, making the load in the dynamic changes.3) There is no specification and technical measures in the different types of commercial projects refer to the detailed parameters of the shops, engineering design load calculation in the lack of data, in most cases to rely on staff with previous experience in engineering design calculations. Load the selection of parameters: for the above problems, the load calculation, the first developer of sales and good communication, to determine the form of layers of the forms and nature of floor area, which is calculated on the basis of electrical load basis; followed to determine parameter index within the unit area of shops is also very important and complex because there is no clear indicator of the specification can refer to; and different levels of economic development between cities is not balanced, power indices are also different; will be in the same city, different regions have different consumer groups .3) the need to factor in the choice: parameters determined, the need for load calculation. Need to factor commonly used method, the calculation will not repeat them. Need to explore is the need for coefficient selection, which in the current specifications, manuals and the "unified technical measures" is also not clear requirements, based on years of design experience that most end shops in the distribution or level within the household distribution box with case Kx generally take a while, in the calculation of the loop route to take 0.7 to 0.8, the distribution transformers in the substation calculations take 0.4 to 0.6.3 substations setLoad calculation based on the results of this project the total installed capacity of transformer 43400Kv.A, after repeated consultations with the power company, respectively, in the project innorthern, central and southern three sections set the three buildings into three power substations, 1 # set 6 sets 2500Kv.A transformer substation, take the northern section of power supply; 2 # 4 1600Kv.A transformer substations located, plus 6 sets 2000Kv.A transformers, take the middle of the power supply, in addition to 5 Taiwan 10Kv.A high-pressure water chillers (total 4000Kv.A); 3 # substation located 2 units plus 2 units 1000Kv.A 2000Kv.A transformers, take the southern section of A, B two office supply. 10Kv power configuration of this project into two points, each at the two 10Kv lines, the power company under the provisions of 10Kv power capacity: maximum load per channel is about to 11000Kv.A, two is the 22000Kv.A, design # 1 , 3 # combination of a substation 10Kv, power line, with a total capacity of 21000Kv.A; 2 # substation transformers and 10Kv, 10Kv chillers sharing a power line, with a total capacity of 22400Kv.A. The design of the substation layout, in addition to meeting regulatory requirements, it also need to consider the high-pressure cabinets, transformers and low voltage power supply cabinet by order of arrangement, especially in low voltage distribution cabinet to feed the cable smooth and easy inspection duty problems are not seriously consider the construction of the cable crossing will cause more long detour, a waste of floor space, and convenient inspections and other issues.4 small fire load power supplyIn the design of large commercial projects often encounter small fire load of electrical equipment and more dispersed distribution, if fed by a substation, a substation will be fed a lot of low-voltage low-current counter circuit breaking capacity circuit breaker and conductor of the dynamic and thermal stability in a certain extent. According to GB50045-1995 "fire protection design of tall buildings," rule "should be used in Fire Equipment dedicated power supply circuit, the power distribution equipment shall be provided with clear signs." Interpretation of the provisions of the power supply circuit means "from the low-voltage main distribution room (including the distribution of electrical room) to last a distribution box, and the general distribution lines should be strictly separated." In this design, the use of methods to increase the level of distribution, that is different from the substation bus segments, respectively, a fire fed a special circuit, set in place two distribution cabinets, distribution cabinets and then the resulting radial allocated to the end of the dual power to vote each box, so that not only meets the specification requirements for dedicated power supply circuit, but also to avoid feeding the substation level of many small current loop.5, the choice of circuit breaker and conductorCommercial real estate projects use the room as the uncertainty in the choice of circuit breakers and conductors must be considered in a certain margin to meet the needs caused by adjustment of the load changes. According to this characteristic, increased use in the design of the plug bus-powered, not only meet the requirements of large carrying capacity, and also allows the flexibility to increase supply and distribution, are reserved in each shaft in the plug-box backup in order to change, according to changes in upper and lower load, to adjust. For example: a bus is responsible for a shaft 1 to 3 layers of power, when a layer due to the change in capacity increases, while the 3-layer capacity is reduced, you can use a spare plug box layer off the 3-layer 1 layer capacity rationing . This level distribution in the substation, select the circuit breaker to choose the setting value when the circuit breaker to adjust to changes at the end to adjust the load setting value; in the bus and the transformer circuit breaker according to the choice of the general framework of values to select . For example: Route certain equipment capacity 530Kv, Kx take 0.7 to calculate current of 704A, select the frame circuit breaker is 1000A, tuning is 800A; currenttransformer for the 1000/50; bus carrying capacity for the 1000A, this road can meet the maximum 1000A current load requirements, even if there is adjustment, power distribution switches and circuit can not make big changes.6 layer distribution box setAccording to the division of layers of fire protection district, respectively numbered as A ~ K layers within the set level shaft for the retail lighting power distribution box, with one on one power supply shops in radial power. Should be noted that the forms of the complex layers of layers of fire partition, does not correspond to the lower, making some of shaft power in charge of the fire district at the same time, also responsible for the power supply adjacent to the fire district. At design time, using the principle of proximity, while also taking into account the burden of the whole trunk load conditions, so that each shaft as far as possible a more balanced load.7 public area distribution box setTaking into account the future needs of the business re-decoration of public areas must be reserved for power. Here the design needs to consider the following points: ①question of how much reserve power, lighting and electricity, which according to GB50034-2004"Architectural Lighting Design Standards" table of Article 6.1.3 and 6.1.8, commercial building lighting power density value, high-end supermarkets, business offices as 20W/m2, under the "decorative lighting included 50% of the total lighting power density calculation" requirements, using the reserved standard 40W/m2. ②In order to facilitate the decoration in each partition set fire lighting in public areas and emergency lighting distribution box distribution box, in order to identify the electrical power distribution decoration cut-off point.③the staircase, storage rooms and other parts of the decoration does not need to do, set the power distribution circuit or a separate distribution box, try not to be reserved from the public area of electricity distribution board fed hardcover out.④control of lighting in public areas, the majority in two ways, namely, C-BUS control system or the BA system, the use of C-BUS has the advantage of more flexible control, each road can be fed out of control, adjustable light control; shortcomings is a higher cost. BA system control advantages of using low cost, simple control; disadvantage is that the exchanges and contacts for the three-phase, three-way control may be related both to open, or both, in the decoration of the contacts required to feed the power supply circuit diverge to avoid failure blackouts.Design of distribution box 8In the commercial real estate design, shop design is often only a meter box, and outlet route back to the needs of the user according to their second design, but the shops are difficult to resolve within the power supply fan coil units, air-conditioning system as a whole can not debug. The project approach is to add a circuit breaker in the meter box for the coil power supply, another way for users to use the second design, as shown below.User distribution box design9 distribution cabinet / box number and distribution circuitsLarge-scale projects are often low voltage distribution cabinet / box number, low-voltage circuits to feed the more often there will be cabinet / box number and line number duplication, resulting in the design and the future looks difficult maintenance and overhaul. The project has three 10Kv substations, 20 transformer, hundreds of low-voltage fed out of the closet, fed the circuit more. Accordance with the International Electrotechnical Commission (IEC) and the Chinese nationalstandard requirements: ①All the distribution number to be simple and clear, not too box and line numbers are not repeated. ②number to simple and clear, not too long. ③distinction between nature and type of load. ④law was easy to find, make viewer at a glance. Based on the above requirements and on the ground, fire district and the underground construction industry form the different conditions, using two slightly different ways. Essential for the underground garage, uses a single comparison, also relatively fire district neat, according to fire district number, such as AL-BL-1 / 1, AP and APE, the meaning of the letters and numbers: AL on behalf of lighting distribution (AP on behalf of Power distribution box, APE on behalf of the emergency power distribution box); BI on behalf of the basement; 1 / 1 for partition 1, I fire box. Above ground is more complex, more fire district, and on the fire district does not correspond to the lower, according to shaft number is better, such as AL-1-A1, AP, and APE, letters and numbers mean: 1 represents a layer; A1 on behalf of A, No. 1 shaft fed a distribution box. Fed a low-voltage circuits, such as the number of uses: W3-6-AL-1-A1, W3-6) indicates that the route back to power supply transformer 3, 6, feed the power distribution cabinet, AL-1-A1, said the then the first loop of the distribution box for the AL-1-A1 and so on, and so on.10 ConclusionWith more and more complex commercial design projects, designers need to continually improve the design level, designed to make fine. These are only bits of the design in the business lessons learned, and the majority of designers want to communicate高层建筑供配电系统设计摘要：随着城市规模的不断发展，高层建筑越来越多，因此，高层建筑电气设计就成为设计者不得不面对的问题。

The Load Estimation and Power Tracking Integrated Control Strategy for Dual-Sides Controlled LCC Compensated WirelessCharging SystemABSTRACT In this paper, the wireless power transfer (WPT) system with dynamic loads such as batteries is studied comprehensively. An integrated control technology of load estimation and power tracking of LCC compensated is proposed, which realizes load estimation, mode judgment and charging control at the transmitter, and standard load setting and decoupling control at the receiver. Based on the inflfluence of reflflection impedance on the output current of the inverter, a method of identifying coupling coeffificient and equivalent load is proposed and a mathematical model is established. Receiver controller provides standard reference load for load estimation. Transmitter controller judges battery status according to the estimation of equivalent load and adopts double closed-loop control to regulate power and current. Receiver decouples control when battery charging voltage reaches the threshold, and providing mode conversion sign for transmitter controller to realize constant current (CC) and constant voltage (CV) charging of battery.The Dual-sides integrated control scheme has no data communication between transmitter and receiver, so it can control independently, which reduces the complexity of the system and is suitable for different charging modes. The proposed controller is more effificient as it maintains a track current, and dynamically alters the pick-up characteristics to suit the load demand. Finally, the simulation and experimental results validate the feasibility of proposed control method, which realizes the estimation of the load and CC/CV charging of the battery. The proposed WPT system achieved the effificiency at 91.16% while delivering 2 kW to the load with a vertical air gap of 150 mm.INDEX TERMS Wireless power transfer, integrated control, load estimation, constant current/voltage charging, LCC compensation, phase shift control.Wireless Power Transmission (WPT) or Contactless Power Transmission (CPT) achieves the power transmission without physical connection, which makes up for the shortcomings of traditional power transmission methods . Wireless charging will promote the development of electric vehicles (EVs), because it provides more convenient, reliable and safer charging options than conductive charging . There are many research fields in WPT for EVs, especially the WPT system is sensitive to coupling coefficient, air gap, resonant frequency, and load change, which makes it hard for There are many research fields in WPT for EVs, especially the WPT system issensitive to coupling coefficient, air gap,resonant frequency, and load change, which makes it hard for robust control, and most scholars focus on the steady state of the WPT systems .When the resonant frequency, position, parameters and load of the wireless charging system change, which result in a higher volt-ampere rating and lower power transfer efficiency. Therefore, resonant compensation is an important part at the transmitter and receiver of the system. Different compensation topologies have been proposed and implemented to tune the two coils working at a resonant frequency in a wide range of applications. there are four basic compensation topologies, namely Series-Series (SS), SeriesParallel (SP), Parallel-Series (PS) and Parallel-Parallel (PP),are widely adopted for EV applications.Many other novel compensation topologies are also used to improve the power transfer efficiency and to simplify the control of WPT systems. Literatures show that LCL topology and series LC topology are the commonly used primary compensation networks for WPT. Compared with series LC, LCL performs better in power conversion efficiency over the full range of coupling and loading imposed, and its constant current source characteristic make its closed-loop control implementation easier. More advantageous compensation topologies are put forward in . The double-sided LCC compensation topology is outstanding since not only is its resonant frequency independent of coupling coefficient and load condition, but also its advantages of facilitating zero voltage switch (ZVS) or zero current switch (ZCS) of the inverter, realize CC charging at zero phase angle (ZPA) condition, increasing lateral misalignment tolerance, and improving WPT efficiency have been demonstrated.The other problem with WPT charger systems is implementing a charge process for EV batteries.Since batteries are considered to be varying loads during charging, the charge converter needs to regulate its output precisely to implement the constant current (CC) charge and constant voltage (CV) mode charge. Thus, meticulous control and tuning of the inverter is necessary since the load varies violently as the receive coil moves with the online EV.This adds to the control complexity and may reduce systematic reliability. In order to improve battery life and charging efficiency, it is necessary for a charger to provide accurate charge current and voltage through stable operations. In recent years, various control strategies have been studied to provide the required output currentorvoltagefortime-varyingloadsatdifferentcharging stages.The traditional control method is to use wireless communication to send the load state information to the transmitter controller to adjust the output power of the inverter to achieve CC/CV charging in . In order to simplify the control of an WPT charger system and avoid the above drawbacks of conventional control methods under wide variations of the load in implementing the CC/CV charge, some researchers have started to utilize the load-independent characteristics of the compensation topologies at their resonant frequencies proposes a design method which makes it possible to implement the CC/CV mode charge with minimum frequency variation during the entire charge process by using the load-independent characteristics of an WPT system under the ZPA condition without any additional switches. But, frequency variation may result in a bifurcation phenomenon,where the control ability and stability of the system are lost.In order to realize ZPA condition in the whole charging process, a switchablehybrid topology is proposed in [19], and [20]. CC and CV charging are realized in different compensation topologies. However, the addition of switches complicates the system, and changes in system parameters can also lead to instability.In[21], a new control technique was proposed, which only employs the controller at transmitting and and load identification approach to adjust charging voltage/current for SS and SP compensated WPT systems. The advantages are that dual-side wireless communication for real-time charging current/voltage adjustment is avoided as well as it is suitable for different charging modes. However, switching between two kinds of topologies is still needed. For the CC/CV charging control at constant frequency, some approaches employ a DC/DC converter to control the output current or voltage while the front-end converter operates at the resonant frequency to achieve the ZPA condition in [22] and [23]. However, this increases the component counts, losses and complexity. In [24], DC/DC converters are used for decoupling control rather than CC or CV charging.In [25]and [26], a single primary-side controller based on phase shift H-bridge inverter are proposed to adjust the charging current or charging voltage against various load, may make it hard for the High frequency inverter to achieve ZVS in full load range, especially with light load condition. Then, the primary-side control method that realizes CC/CV charging for battery is analyzed, which is the main contribution of this paper.The objective of this research is to study and develop a new integrated control strategy for load and power tracking that realizes CC/CV charging for LCC compensation through the double-loop controlled phase shift H-bridge inverter and load identification approach. The system adopts dual-side controller to avoid wireless communication, and the mathematical models of load estimation and mode judgment are derived by using the topological compensation characteristics of double-sided LCC. The working state of the battery is fed back to the transmitter controller by reflecting the impedance of the receiver, and the coupling coefficient of coils and load value are estimated.The transmitter judges the charging mode according to the estimated load, adjusts the output power of the inverter, and maintains CC/CV charging by phase-shifting control. In CC mode, the transmitter can transfer more power and prevents overloading. In CV mode, the output power can be adjusted according to the charging curve. The receiver control circuit adopts Buck-Boost structure. Different from the traditional impedance matching or CC/CV charging control mode, the receiver controller sets the standard reference value of load estimation control by impedance matching. Buck-Boost converter operates in switching mode during charging. When the charging voltage reaches the reference value, the switching action changes the reflection impedance and provides the mode conversion mark for the transmitter. Based on the feedback signal and the amount of transferred power, the controlling module continuously adjusts the transmitting coil current during the charging.The rest of the sections are organized as follows:Section II gives the system structure and basic theoretical analysis. Section III proposes the integrated control method of load estimation and power tracking, and then the double closed-loop PIcontroller of transmitter and receiver is designed. Section IV validates the proposed method with simulations and experiments.Finally,last section summarizes the conclusions drawn from the investigation.II. SYSTEM STRUCTURE AND THEORETICAL ANALYSISIn this section, the system structure and methodology for analyzing the WPT system are discussed. Then, basic output characteristics for LCC compensation are analyzed to propose the Integrated control method on the transmitting side and the receiving side.A.WIRELESS POWER TRANSMISSION SYSTEM TRUCTURE In this paper, the most widely used variable impedance load battery is taken as the research object.Charging characteristic curve of the battery is shown in Figure 1. Charging process includes CC/CV charging. In CC stage, the output power of the power supply increases with the increase of the battery terminal voltage, while the equivalent impedance of the battery increases with little change. In the CV stage, the charge current and power decrease,and the equivalent impedance of the battery increases rapidly.B. LOAD ESTIMATE AND MODEL RECOGNITION The transmitter controller measures Iinv to estimate the load and mutual inductance changes, and judges the working state of the receiver. The inverter operates at ZPA resonant frequency and the controller adjusts fro m 180◦ phase shift, which means that the minimum input voltage is applied to the transmitting coil. According to the requirement of the receiver, the power control unit uses phase shift control to adjust the It and VC to keep the CC and CV working modes at the receiver.The transmitter can control the power output according to the working mode of the receiver and the load demand. In order to achieve this function, the designed controller should be able to estimate mutual inductance and equivalent load, and then judge the charging mode of the receiving end. The control block diagram of load estimation and mode judgment strategy is shown in Figure 5. Where, Rx is the standard reference load of the receiver.CONCLUSION An integrated control method of load estimation and power tracking is proposed in this paper to achieve CC/CV charging.of LCC compensation WPT system. Firstly, through theoretical analysis, the LCC compensation topology can realize the charge of CC mode under ZPA condition, and get the relationship between the equivalent load and the current of the inverters. Then, a standard reference load is set at the receiver so that the transmitter can estimate the equivalent load by calculating the refection impedance and detecting the output current of the inverter. Finally, according to the estimated load value and the conversion mark given by the decoupling control of the receiver, the CC/CV charging for LCC compensation are realized by PI controlled phase shift full-bridge inverter. The simulation and experimental results validate the feasibility of the proposed control method for whole load changes. The proposed WPT system can achieve a high effenciency at 91.16% with a 20-cm air gap when delivering 0.2−2kW to the load in different charging stages.双边控制的LCC补偿型无线充电系统的负载估计与功率跟踪集成控制策略摘要本文对电池等动态负载下的无线电能传输（WPT）系统进行了全面的研究。

forced concrete structure reinforced with anoverviewReinSince the reform and opening up, with the national economy's rapid and sustained development of a reinforced concrete structure built, reinforced with the development of technology has been great. Therefore, to promote the use of advanced technology reinforced connecting to improve project quality and speed up the pace of construction, improve labor productivity, reduce costs, and is of great significance.Reinforced steel bars connecting technologies can be divided into two broad categories linking welding machinery and steel. There are six types of welding steel welding methods, and some apply to the prefabricated plant, and some apply to the construction site, some of both apply. There are three types of machinery commonly used reinforcement linking method primarily applicable to the construction site. Ways has its own characteristics and different application, and in the continuous development and improvement. In actual production, should be based on specific conditions of work, working environment and technical requirements, the choice of suitable methods to achieve the best overall efficiency.1、steel mechanical link1.1 radial squeeze linkWill be a steel sleeve in two sets to the highly-reinforced Department with superhigh pressure hydraulic equipment (squeeze tongs) along steel sleeve radial squeeze steel casing, in squeezing out tongs squeeze pressure role of a steel sleeve plasticity deformation closely integrated with reinforced through reinforced steel sleeve and Wang Liang's Position will be two solid steel bars linkedCharacteristic: Connect intensity to be high, performance reliable, can bear high stress draw and pigeonhole the load and tired load repeatedly.Easy and simple to handle, construction fast, save energy and material, comprehensive economy profitable, this method has been already a large amount of application in the project.Applicable scope : Suitable for Ⅱ, Ⅲ, Ⅳgrade reinforcing bar (including welding bad reinfor cing bar ) with ribbing of Ф 18- 50mm, connection between the same diameter or different diameters reinforcing bar .1.2must squeeze linkExtruders used in the covers, reinforced axis along the cold metal sleeve squeeze dedicated to insert sleeve Lane two hot rolling steel drums into a highly integrated mechanical linking methods.Characteristic: Easy to operate and joining fast and not having flame homework , can construct for 24 hours , save a large number of reinforcing bars and energy. Applicable scope : Suitable for , set up according to first and second class antidetonation requirement -proof armored concrete structure ФⅡ, Ⅲgrade reinforcing bar with ribbing of hot rolling of 20- 32mm join and construct live.1.3 cone thread connectingUsing cone thread to bear pulled, pressed both effort and self-locking nature, undergo good principles will be reinforced by linking into cone-processing thread at the moment the value of integration into the joints connecting steel bars.Characteristic: Simple , all right preparatory cut of the craft , connecting fast, concentricity is good, have pattern person who restrain from advantage reinforcing bar carbon content.Applicable scope : Suitable for the concrete structure of the industry , civil buil ding and general structures, reinforcing bar diameter is for Фfor the the 16- 40mm one Ⅱ, Ⅲgrade verticality, it is the oblique to or reinforcing bars horizontal join construct live.conclusionsThese are now commonly used to connect steel synthesis methods, which links technology in the United States, Britain, Japan and other countries are widely used. There are different ways to connect their different characteristics and scope of theactual construction of production depending on the specific project choose a suitable method of connecting to achieve both energy conservation and saving time limit for a project ends.钢筋混凝土结构中钢筋连接综述改革开放以来，随着国民经济的快速、持久发展，各种钢筋混凝土建筑结构大量建造，钢筋连接技术得到很大的发展。

外文文献翻译(含：英文原文及中文译文)译文字数：3700多字文献出处：J Ehnberg. Power of Community Distribution to Design[J] Value Engineering, 2016, 2(3):14-21英文原文Power of Community Distribution to DesignJ EhnbergABSTRACTThe basic function of the electric power system is to transport the electric power towards customers. The l0kV electric distribution net is a key point that connects the power supply with the electricity using on the industry, business and daily-life. For the electric power, allcostumers expect to pay the lowest price for the highest reliability, but don't consider that it's self-contradictory in the co-existence of economy and reliable.To improve the reliability of the power supply network, we must increase the investment cost of the network construction But, if the cost that improve the reliability of the network construction, but the investment on this kind of construction would be worthless if the reducing loss is on the power-off is less than the increasing investment on improving the reliability .Thus we find out a balance point to make the most economic, between the investment and the loss by calculating the investment onpower net and the loss brought from power-off.KEYWORDS: power supply and distribution, power distribution reliability , reactive compensation, load distributionIn general, major changes to the building include: high voltage and low voltage distribution systems, transformers, and backup power systems. Power systems include power distribution and control, indoor and outdoor lighting systems include all types of lighting, and lightning protection systems include intrusion protection, lightning sensors, grounding, equipotential bonding, and local equipotential bonding. Auxiliary equipotential bonding. In just 20 years, the system has undergone enormous changes in the face of technology and products. Many design ideas have also changed dramatically. Switchgear, such as the first circuit-breaker oil circuit breaker in a high-voltage system, and the subsequent development of an oil circuit breaker, are not only large in size but generally contain oil. Due to the large size of the switchgear, we must also establish a separate equipment room that occupies a large amount of floor area. Vacuum circuit breakers and sulfur hexafluoride circuit breakers are not only small in size, but also have a large short-circuit capacity. The size of the housing is much larger than that of the original cabinets, and the circuit breakers do not have any oil and the fire performance is greatly improved. And circuit breakers and other low-voltage devices are in one room, which saves space and is easy tomanage. In the past, large-capacity low-voltage circuit breakers gradually increased the capacity of the short-circuit current, gradually reduced the scale, and became more stable, making the system safer and more reliable, which facilitated the design. Towards the development of intelligent low-voltage circuit breakers, various parameters of the circuit breaker can be controlled by the bus industry and the signals are transmitted directly to the computer.The appearance of dry-type transformers has brought great convenience to the electrical design of buildings because there is no possibility of leakage of transformer oil and fire so that it can be easily installed in the building itself and even directly into the load center. It also eliminates the transformer's demand for oil and can use dry-type transformers when building large-capacity equipment. Four Taiwanese 2500kV A dry-type transformers have been used in actual engineering design.In terms of using emergency generators, it is much more advanced than in the past in terms of performance and size. In addition to using diesel generators; emergency lighting uses EPS standby power; devices that interrupt power within a millisecond can use UPS.The control of electrical equipment varies from the control of a single component to the control of relays. In addition to the smaller size of the various components for better performance, the specification of thecontrol box is also reduced. Because digital technology is more used in control to achieve the best control status to control the equipment. Further improve the effect of energy conservation.The revolution of electric power system has brought a new big round construction, which is pushing the greater revolution of electric power technique along with the application of new technique and advanced equipment. Especially, the combination of the information technique and electric power technique, to great ex- tent, has improved reliability on electric quality and electric supply. The technical development decreases the cost on electric construction and drives innovation of electric network. On the basis of national and international advanced electric knowledge, the dissertation introduces the research hotspot for present electric power syetem as following.Firstly, This dissertation introduces the building condition of distribution automation(DA), and brings forward two typical construction modes on DA construction, integrative mode and fission mode .It emphasize the DA structure under the condition of the fission mode and presents the system configuration, the main station scheme, the feeder scheme, the optimized communication scheme etc., which is for DA research reference.Secondly, as for the (DA) trouble measurement, position, isolation and resume, This dissertation analyzes the changes of pressure andcurrent for line problem, gets math equation by educing phase short circuit and problem position under the condition of single-phase and works out equation and several parameter s U& , s I& and e I& table on problem . It brings out optimized isolation and resume plan, realizes auto isolation and network reconstruction, reduces the power off range and time and improves the reliability of electric power supply through problem self- diagnoses and self-analysis. It also introduces software flow and use for problem judgement and sets a model on network reconstruction and computer flow.Thirdly, electricity system state is estimated to be one of the key techniques in DA realization. The dissertation recommends the resolvent of bad measurement data and structure mistake on the ground of describing state estimate way. It also advances a practical test and judging way on topology mistake in state estimate about bad data test and abnormity in state estimate as well as the problem and effect on bad data from state measure to state estimate .As for real time monitor and control problem, the dissertation introduces a new way to solve them by electricity break and exceptional analysis, and the way has been tested in Weifang DA.Fourthly, about the difficulty for building the model of load forecasting, big parameter scatter limit and something concerned, the dissertation introduces some parameters, eg. weather factor, date type andsocial environment effect based on analysis of routine load forecasting and means. It presents the way for electricity load forecasting founded on neural network(ANN),which has been tested it’s validity by example and made to be good practical effect.Fifthly, concerning the lack of concordant wave on preve nting concordant wave and non-power compensation and non-continuity on compensation, there is a topology structure of PWM main circuit and nonpower theory on active filter the waves technique and builds flat proof on the ground of Saber Designer and proves to be practical. Meanwhile, it analyzes and designs the way of non-power need of electric network tre- nds and decreasing line loss combined with DA, which have been tested its objective economic benefit throu- gh counting example.Sixthly, not only do the dissertation design a way founded on the magrginal electric price fitted to our present national electric power market with regards to future trends of electric power market in China and fair trade under the government surveillance, that is group competitio n in short-term trade under the way of grouped price and quantity harmony, but also puts forward combination arithmetic, math model of trading plan and safty economical restriction. It can solve the original contradiction between medium and long term contract price and short term competitive price with improvement on competitive percentage and cut down the unfair income difference of electric factory, at the same time,it can optimize the electric limit for all electric factories and reduce the total purchase charge of electric power from burthen curve of whole electric market network.The distribution network is an important link among the power system. Its neutral grounding mode and operation connects security and stability of the power system directly. At the same time, the problem about neutral grounding is associated with national conditions, natural environment, device fabrication and operation. For example, the activity situation of the thunder and lightning, insulating structure and the peripheral interference will influence the choice of neutral grounding mode Conversely, neutral grounding mode affects design, operation, debugs and developing. Generally in the system higher in grade in the voltage, the insulating expenses account for more sizable proportion at the total price of the equipment. It is very remarkable to bring the economic benefits by reducing the insulating level. Usually such system adopt the neutral directly grounding and adopt the autoreclosing to guarantee power supply reliability. On the contrary, the system which is lower in the voltage adopts neutral none grounding to raise power supply reliability. So it is an important subject to make use of new- type earth device to apply to the distribution network under considering the situation in such factors of various fields as power supply reliability, safety factor, over-voltage factor, the choice of relay protection, investment cost, etc.The main work of this paper is to research and choice the neutral grounding mode of the l0kV distribution network. The neutral grounding mode of the l0kV network mainly adopts none grounding, grounding by arc suppressing coil, grounding by reactance grounding and directly grounding. The best grounding mode is confirmed through the technology comparison. It can help the network run in safety and limit the earth electric arc by using auto-tracking compensate device and using the line protection with the detection of the sensitive small ground current. The paper introduces and analyzes the characteristic of all kind of grounding modes about l0kV network at first. With the comparison with technological and economy, the conclusion is drawn that the improved arc suppressing coil grounding mode shows a very big development potential.Then, this paper researches and introduces some operation characteristics of the arc suppressing coil grounding mode of the l0kV distribution network. And then the paper put emphasis on how to extinguish the earth electric arc effectively by utilizing the resonance principle. This paper combines the development of domestic and international technology and innovative achievement, and introduces the computer earth protection and autotracking compensate device. It proves that the improved arc suppressing coil grounding mode have better operation characteristics in power supply reliability, personal security,security of equipment and interference of communication. The application of the arc suppressing coil grounding mode is also researched in this paper.Finally, the paper summarizes this topic research. As a result of the domination of the arc suppressing coil grounding mode, it should be more popularized and applied in the distribution network in the future.The way of thinking, project and conclusions in this thesis have effect on the research to choose the neutral grounding mode not only in I0kV distribution network but also in other power system..The basic function of the electric power system is to transport the electric power towards customers. The l0kV electric distribution net is a key point that connects the power supply with the electricity using on the industry, business and daily-life. For the electric power, all costumers expect to pay the lowest price for the highest reliability, but don't consider that it's self-contradictory in the co-existence of economy and reliable. To improve the reliability of the power supply network, we must increase the investment cost of the network con- struction But, if the cost that improve the reliability of the network construction, but the investment on this kind of construction would be worthless if the reducing loss is on the power-off is less than the increasing investment on improving the reliability .Thus we find out a balance point to make the most economic, between the investment and the loss by calculating the investment onpower net and the loss brought from power-off. The thesis analyses on the economic and the reliable of the various line modes, according to the characteristics various line modes existed in the electric distribution net in foshan..First, the thesis introduces as the different line modes in the l0kV electric distribution net and in some foreign countries. Making it clear tow to conduct analyzing on the line mode of the electric distribution net, and telling us how important and necessary that analyses are.Second, it turns to the necessity of calculating the number of optimization subsection, elaborating how it influences on the economy and reliability. Then by building up the calculation mode of the number of optimization subsection it introduces different power supply projects on the different line modes in brief. Third, it carries on the calculation and analyses towards the reliability and economy of the different line modes of electric distribution net, describing drafts according by the calculation. Then it makes analysis and discussion on the number of optimization subsection.At last, the article make conclusion on the economy and reliability of different line modes, as well as, its application situation. Accordion to the actual circumstance, the thesis puts forward the beneficial suggestion on the programming and construction of the l0kV electric distribution net in all areas in foshan. Providing the basic theories and beneficial guidelinefor the programming design of the lOkV electric distribution net and building up a solid net, reasonable layout, qualified safe and efficiently-worked electric distribution net.Auto-Tune SequenceThe auto-tuning sequence begins after the hysteresis and deviation values have been determined. The tuning process begins when the initial output step is applied to the loop output.This change in output value should cause a corresponding change in the value of the process variable. When the output change drives the PV away from setpoint far enough to exceed the hysteresis boundary a zero-crossing event is detected by the auto-tuner. Upon each zero crossing event the auto-tuner drives the output in the opposite direction.The tuner continues to sample the PV and waits for the next zero crossing event. A total of twelve zero-crossings are required to complete the sequence. The magnitude of the observed peak-to-peak PV values (peak error) and the rate at which zero-crossings occur are directly related to the dynamics of the process. Early in the auto-tuning process, the output step value is proportionally adjusted once to induce subsequent peak-to-peak swings of the PV to more closely match the desired deviation amount. Once the adjustment is made, the new output step amount is written into the Actual Step Size field (ASTEP) of the loop table. The auto-tuning sequence will be terminated with an error, if thetime between zero crossings exceeds the zero crossing watchdog interval time. The default value for the zero crossing watchdog interval time is two hours.中文译文住宅小区配电设计J Ehnberg摘要电力系统的基本功能是向客户输送电力。

电气工程高层建筑论文中英文资料外文翻
译文献
本文的主要目标是翻译一些电气工程和高层建筑方面的外文文献。

这些文献分别为：
1. "Application of lateral tuned mass damper to high-rise structure under random wind excitations"，这篇文章主要介绍了侧向调谐质量阻尼器（lateral tuned mass damper）在高层建筑中的应用。

该文通过计算分析和试验研究，得出了调谐阻尼器的结构参数和其对建筑物抗震能力的影响。

2. "Reliability Analysis of Power Supply System in High-rise Building"，这篇文章主要介绍了高层建筑电力供应系统的可靠性分析。

该文分别从电力系统的结构、功能和基本原理入手，阐述了电力系统的可靠性分析方法，并根据有关标准和规范，对高层建筑电力系统的可靠性进行了分析。

3. "Dynamic Analysis on Earthquake Resistance of High-rise Buildings Based on Pushover Method"，该文介绍了基于 Pushover 方
法对高层建筑的抗震性能进行动力学分析。

该方法通过对结构的位移、剪力和弯矩等特性进行预测，可以更加准确地评估高层建筑的抗震性能。

以上三篇文献分别介绍了高层建筑中的电气工程和抗震技术方面的研究成果，对于高层建筑的设计和建造具有一定的参考价值。

forced concrete structure reinforced with anoverviewReinSince the reform and opening up, with the national economy's rapid and sustained development of a reinforced concrete structure built, reinforced with the development of technology has been great. Therefore, to promote the use of advanced technology reinforced connecting to improve project quality and speed up the pace of construction, improve labor productivity, reduce costs, and is of great significance.Reinforced steel bars connecting technologies can be divided into two broad categories linking welding machinery and steel. There are six types of welding steel welding methods, and some apply to the prefabricated plant, and some apply to the construction site, some of both apply. There are three types of machinery commonly used reinforcement linking method primarily applicable to the construction site. Ways has its own characteristics and different application, and in the continuous development and improvement. In actual production, should be based on specific conditions of work, working environment and technical requirements, the choice of suitable methods to achieve the best overall efficiency.1、steel mechanical link1.1 radial squeeze linkWill be a steel sleeve in two sets to the highly-reinforced Department with superhigh pressure hydraulic equipment (squeeze tongs) along steel sleeve radial squeeze steel casing, in squeezing out tongs squeeze pressure role of a steel sleeve plasticity deformation closely integrated with reinforced through reinforced steel sleeve and Wang Liang's Position will be two solid steel bars linkedCharacteristic: Connect intensity to be high, performance reliable, can bear high stress draw and pigeonhole the load and tired load repeatedly.Easy and simple to handle, construction fast, save energy and material, comprehensive economy profitable, this method has been already a large amount of application in the project.Applicable scope : Suitable for Ⅱ, Ⅲ, Ⅳgrade reinforcing bar (including welding bad reinfor cing bar ) with ribbing of Ф 18- 50mm, connection between the same diameter or different diameters reinforcing bar .1.2must squeeze linkExtruders used in the covers, reinforced axis along the cold metal sleeve squeeze dedicated to insert sleeve Lane two hot rolling steel drums into a highly integrated mechanical linking methods.Characteristic: Easy to operate and joining fast and not having flame homework , can construct for 24 hours , save a large number of reinforcing bars and energy. Applicable scope : Suitable for , set up according to first and second class antidetonation requirement -proof armored concrete structure ФⅡ, Ⅲgrade reinforcing bar with ribbing of hot rolling of 20- 32mm join and construct live.1.3 cone thread connectingUsing cone thread to bear pulled, pressed both effort and self-locking nature, undergo good principles will be reinforced by linking into cone-processing thread at the moment the value of integration into the joints connecting steel bars.Characteristic: Simple , all right preparatory cut of the craft , connecting fast, concentricity is good, have pattern person who restrain from advantage reinforcing bar carbon content.Applicable scope : Suitable for the concrete structure of the industry , civil buil ding and general structures, reinforcing bar diameter is for Фfor the the 16- 40mm one Ⅱ, Ⅲgrade verticality, it is the oblique to or reinforcing bars horizontal join construct live.conclusionsThese are now commonly used to connect steel synthesis methods, which links technology in the United States, Britain, Japan and other countries are widely used. There are different ways to connect their different characteristics and scope of the actual construction of production depending on the specific project choose a suitable method of connecting to achieve both energy conservation and saving time limit for a project ends.钢筋混凝土构造中钢筋连接综述改革开放以来，伴随国民经济旳迅速、持久发展，多种钢筋混凝土建筑构造大量建造，钢筋连接技术得到很大旳发展。

外文资料Along with the development of the ages, the technique that is nowadays is also gradually perfect, the competition plays more more strong; the operation that list depends the artificial has already can't satisfied with the current manufacturing industry foreground, also can't guarantee the request of the higher quantity and high new the image of the technique business enterprise.The people see in produce practice, automate brought the tremendous convenience and the product quantities for people up of assurance, also eased the personnel's labor strength, reduce the establishment on the personnel. The target control of the hard realization in many complicated production lines, whole and excellent turn, the best decision etc., well-trained operation work, technical personnel or expert, governor but can judge and operate easily, can acquire the satisfied result. The research target of the artificial intelligence makes use of the calculator exactly to carry out, imitate these intelligences behavior, moderating the work through person's brain and calculators, with the mode that person's machine combine, for resolve the very complicated problem to look for the best pathWe come in sight of the control that links after the electric appliances in various situation, that is already the that time generation past, now of after use in the mold a perhaps simple equipments of grass-roots control that the electric appliances can do for the low level only;And the PLC emergence also became the epoch-making topic, adding the vivid software control through a very and stable hardware, making the automation head for the new high tide.The PLC biggest characteristics lie in: The electrical engineering teacher already no longer electric hardware up too many calculationses of cost, as long as order the importation that the button switch or the importation of the sensors order to link the PLC up can solve problem, pass to output to order the conjunction contact machine or control the start equipments of the big power after the electric appliances, but theexportation equipments direct conjunction of the small power can.PLC internal containment have the CPU of the CPU, and take to have an I/ O for expand of exterior to connect a people's address and saving machine three big pieces to constitute, CPU core is from an or many is tired to add the machine to constitute, mathematics that they have the logic operation ability, and can read the procedure save the contents of the machine to drive the homologous saving machine and I/ Os to connect after pass the calculation; The I/ O add inner part is tired the input and output system of the machine and exterior link, and deposit the related data into the procedure saving machine or data saving machine; The saving machine can deposit the data that the I/ O input in the saving machine, and in work adjusting to become tired to add the machine and I/ Os to connect, saving machine separately saving machine RAM of the procedure saving machine ROM and datas, the ROM can can do deposit of the data permanence in the saving machine, but RAM only for the CPU computes the temporary calculation usage of hour of buffer space.The PLC anti- interference is very and excellent, our root need not concern its service life and the work situation bad, these all problems have already no longer become the topic that we fail, but stay to our is a concern to come to internal resources of make use of the PLC to strengthen the control ability of the equipments for us, make our equipments more gentle.PLC language is not we imagine of edit collected materials the language or language of Cs to carry on weaving the distance, but the trapezoid diagram that the adoption is original after the electric appliances to control, make the electrical engineering teacher while weaving to write the procedure very easy comprehended the PLC language, and a lot of non- electricity professional also very quickly know and go deep into to the PLC.Is PLC one of the advantage above and only, this is also one part that the people comprehend more and easily, in a lot of equipmentses, the people have already no longer hoped to see too many control buttons, they damage not only and easily and produce the artificial error easiest, small is not a main error perhaps you can still accept; But lead even is a fatal error greatly is what we can't is tolerant of. Newtechnique always for bringing more safe and convenient operation for us, make we a lot of problems for face on sweep but light, do you understand the HMI? Says the HMI here you basically not clear what it is, also have no interest understanding, change one inside text explains it into the touch to hold or man-machine interface you knew, it combines with the PLC to our larger space.HMI the control not only only is reduced the control press button, increase the vivid of the control, more main of it is can sequence of, and at can the change data input to output the feedback with data, control in the temperature curve of imitate but also can keep the manifestation of view to come out. And can write the function help procedure through a plait to provide the help of various what lies in one's power, the one who make operate reduces the otiose error. Currently the HMI factory is also more and more, the function is also more and more strong, the price is also more and more low, the noodles of the usage are wide more and more. The HMI foreground can say that think ° to be good very.At a lot of situations, the list is is a smooth movement that can't guarantee the equipments by the control of the single machine, but pass the information exchanges of the equipments and equipments to attain the result that we want. For example fore pack and the examination of the empress work preface, we will arrive wrapping information feedback to examine the place, and examine the information of the place to also want the feedback to packing. Pass the information share thus to make both the chain connect, becoming a total body, the match of your that thus make is more close, at each other attain to reflect the result that mutually flick.The PLC correspondence has already come more more body now its value, at the PLC and correspondence between PLCs, can pass the communication of the information and the share of the datas to guarantee that of the equipments moderates mutually, the result that arrive already to repair with each other. Data conversion the adoption RS232 between PLC connect to come to the transmission data, but the RS232 pick up a people and can guarantee 10 meters only of deliver the distance, if in the distance of 1000 meters we can pass the RS485 to carry on the correspondence, the longer distance can pass the MODEL only to carry on deliver.The PLC data transmission is just to be called a form to it in a piece of and continuous address that the data of the inner part delivers the other party, we, the PLC of the other party passes to read data in the watch to carry on the operation. If the data that data in the watch is a to establish generally, that is just the general data transmission, for example today of oil price rise, I want to deliver the price of the oil price to lose the oil ally on board, that is the share of the data; But take data in the watch for an instruction procedure that controls the PLC, that had the difficulty very much, for example you have to control one pedestal robot to press the action work that you imagine, you will draw up for it the form that a procedure combine with the data sends out to pass by.The form that information transport contain single work, the half a work and the difference of a workses .The meaning of the single work also is to say both, a can send out only, but a can receive only, for example a spy he can receive the designation of the superior only, but can't give the superior reply; A work of half is also 2 and can can send out similar to accept the data, but can't send out and accept at the same time, for example when you make a phone call is to can't answer the phone, the other party also; But whole pair works is both can send out and accept the data, and can send out and accept at the same time. Be like the Internet is a typical example.The process that information transport also has synchronous and different step cent: The data line and the clock lines are synchronous when synchronous meaning lie in sending out the data, is also the data signal and the clock signals to be carry on by the CPU to send out at the same time, this needs to all want the specialized clock signal each other to carry on the transmission and connect to send, and is constrained, the characteristics of this kind of method lies in its speed very quick, but correspond work time of take up the CPU and also want to be long oppositely, at the same time the technique difficulty also very big. Its request lies in can'ting have an error margins in a datas deliver, otherwise the whole piece according to compare the occurrence mistake, this on the hardware is a bigger difficulty. Applied more and more extensive in some appropriative equipmentses, be like the appropriative medical treatment equipments, the numerical signal equipments...etc., in compare the one data deliver,its result is very good.And the different step is an application the most extensive, this receive benefit in it of technique difficulty is opposite and want to be small, at the same time not need to prepare the specialized clock signal, its characteristics to lie in, its data is partition, the long-lost send out and accept, be the CPU is too busy of time can grind to a stop sex to work, also reduced the difficulty on the hardware, the data throw to lose at the same time opposite want to be little, we can pass the examination of the data to observe whether the data that we send out has the mistake or not, be like strange accidentally the method, tired addition and eight efficacies method etc., can use to helps whether the data that we examine to send out have or not the mistake occurrence, pass the feedback to carry on the discriminator.A line of transmission of the information contain a string of and combine the cent of: The usual PLC is 8 machines, certainly also having 16 machines. We can be an at the time of sending out the data a send out to the other party, also can be 88 send out the data to the other party, an and 8 differentiationses are also the as that we say to send out the data and combine sends out the data. A speed is more and slowly, but as long as 2 or three lines can solve problem, and can use the telephone line to carry on the long range control. But combine the oscular transmission speed is very quick of, it is a string of oscular of 25600%, occupy the advantage in the short distance, the in view of the fact TTL electricity is even, being limited by the scope of one meter generally, it combine unwell used for the data transmission of the long pull, thus the cost is too expensive.Under a lot of circumstances we are total to like to adopt the string to combine the conversion chip to carry on deliver, under this kind of circumstance not need us to carry on to depositted the machine to establish too and complicatedly, but carry on the data exchanges through the data transmission instruction directly, but is not a very viable way in the correspondence, because the PLC of the other party must has been wait for your data exportation at the time of sending out the data, it can't do other works.When you are reading the book, you hear someone knock on door, you stop tostart up of affair, open the door and combine to continue with the one who knock on door a dialogue, the telephone of this time rang, you signal hint to connect a telephone, after connecting the telephone through, return overdo come together knock on door to have a conversation, after dialogue complete, you continue again to see your book, this kind of circumstance we are called the interruption to it, it has the authority, also having sex of have the initiative, the PLC had such function .Its characteristics lie in us and may meet the urgently abrupt affairs in the operation process of the equipments, we want to stop to start immediately up of work, the whereabouts manages the more important affair, this kind of circumstance is we usually meet of, PLC while carry out urgent mission, total will keep the current appearance first, for example the address of the procedure, CPU of tired add the machine data etc., be like to to stick down which the book that we see is when we open the door the page or simply make a mark, because we treat and would still need to continue immediately after book of see the behind. The CPU always does the affair that should do according to our will, but yo ur mistake of give it an affair, it also would be same to do, this we must notice.The interruption is not only a, sometimes existing jointly with the hour several inside break, break off to have the preferred Class, they will carry out the interruption of the higher Class according to person's request. This kind of breaks off the medium interruption to also became to break off the set. The Class that certainly break off is relevant according to various resources of CPU with internal PLC, also following a heap of capacity size of also relevant fasten.The contents that break off has a lot of kinds, for example the exterior break off, correspondence in of send out and accept the interruption and settle and the clock that count break off, still have the WDT to reset the interruption etc., they enriched the CPU to respond to the category while handle various business. Speak thus perhaps you can't comprehend the internal structure and operation orders of the interruption completely also, we do a very small example to explain.Each equipments always will not forget a button, it also is at we meet the urgent circumstance use of, that is nasty to stop the button. When we meet the Human body trouble and surprised circumstances we as long as press it, the machine stops alloperations immediately, and wait for processing the over surprised empress recover the operation again.Nasty stop the internal I/ O of the internal CPU of the button conjunction PLC to connect up, be to press button an exterior to trigger signal for CPU, the CPU carries on to the I/ O to examine again, being to confirm to have the exterior to trigger the signal, CPU protection the spot breaks off procedure counts the machine turn the homologous exterior I/ O automatically in the procedure to go to also, be exterior interruption procedure processing complete, the procedure counts the machine to return the main procedure to continue to work.Have 1:00 can what to explain is we generally would nasty stop the button of exterior break off to rise to the tallest Class, thus guarantee the safety.When we are work a work piece, giving the PLC a signal, counting PLC inner part the machine add 1 to compute us for a day of workload, a count the machine and can solve problem in brief, certainly they also can keep the data under the condition of dropping the electricity, urging the data not to throw to lose, this is also what we hope earnestly.The PLC still has the function that the high class counts the machine, being us while accept some datas of high speed, the high speed that here say is the data of the in all aspects tiny second class, for example the bar code scanner is scanning the data continuously, calculating high-speed signal of the data processor DSP etc., we will adopt the high class to count the machine to help we carry on count. It at the PLC carries out the procedure once discover that the high class counts the machine to should of interruption, will let go of the work on the hand immediately. The trapezoid diagram procedure that passes by to weave the distance again explains the high class for us to carry out procedure to count machine would automatic performance to should of work, thus rise the Class that the high class counts the machine to high one Class.You heard too many this phrases perhaps:" crash", the meaning that is mostly is a workload of CPU to lead greatly, the internal resources shortage etc. the circumstance can't result in procedure circulate. The PLC also has the similar circumstance, there is a watchdog WDT in the inner part of PLC, we can establishtime that a procedure of WDT circulate, being to appear the procedure to jump to turn the mistake in the procedure movement process or the procedure is busy, movement time of the procedure exceeds WDT constitution time, the CPU turn but the WDT reset the appearance. The procedure restarts the movement, but will not carry on the breakage to the interruption.The PLC development has already entered for network ages of correspondence from the mode of the one, and together other works control the net plank and I/ O card planks to carry on the share easily. A state software can pass all se hardwares link, more animation picture of keep the view to carries on the control, and cans pass the Internet to carry on the control in the foreign land, the blast-off that is like the absolute being boat No.5 is to adopt this kind of way to make airship go up the sky.The development of the higher layer needs our continuous effort to obtain.The PLC emergence has already affected a few persons fully, we also obtained more knowledge and precepts from the top one experience of the generation, coming to the continuous development PLC technique, push it toward higher wave tide.。

文献出处：Fischer M. The Study on the Design of Building Electrical Data Acquisition System and Fault Diagnosis [J]. Building and Environment, 2015, 5（6）: 241-251.原文The Study on the Design of Building Electrical Data Acquisition System and FaultDiagnosisFischer MAbstractBuilding electrical systems can provide energy, and take the function of distribution power for buildings. It is an integral part of construction engineering. As people demand for work and living environment is getting higher and higher, and the continuous development of information technology, building electrical covered more widely, the content of the system structure is more complicated. Although compared to residential buildings in industrial buildings and other large public and commercial buildings, its electrical system structure is relatively simple, less electricity equipment complexity, but because of its use function, the electric system of residential type building also has its own characteristics and requirements. Once its electrical system failure, will lead to economic loss, disastrous, even safety accidents. So, need to be in fault occurs can rapidly and accurately judge the reason, location and damage degree, to reduce loss, lower maintenance costs.Keywords: Building Electrical; Data Acquisition; Fault Diagnosis; SVM1 IntroductionThe speeding up of urbanization leads to more and more buildings. And building electric serves as an integral part of construction engineering, undertaking to provide power for building, distribution, dynamic role, can be said to be the "engine" of the whole building. Building electrical is the use of electrical technology and electrical equipment, through the building space to create the sound, electricity, light, heat, wet, communication and management of the environment, to make it more suitable human life and the work of a kind of integrated disciplines. The "electric technology" refers to the power, information, and all kinds of intelligent building technology ofintegrated disciplines. Building electric is traditionally divided into two parts, heavy current and weak current. Building power supply, lighting, power, lightning protection and grounding part belong to high voltage, etc. Electricity from the substation, through the step-down 380/220 v output power distribution equipment, bus bar, cable, wire transmission power supply equipment, such as elevators, air conditioning, etc. Among them, the lightning protection system is mainly to prevent building caused by lightning strike damage. Grounding system is divided into protective earthling and work, its role is to ensure that the power system and equipment meet the work requirements, to prevent the occurrence of over voltage, system guarantee personal safety at the same time. Extra Low V oltage part include TV, radio, security, fire control and computer system, etc. Therefore, the related research is becoming more and more brought to the attention of the engineering and research workers. In order to satisfy the people to the requirement of working and living environment is getting higher and higher, and the continuous development of information technology, modern buildings in various equipment and subsystem is also more and more. And all equipment and systems in the buildings depends on electrical systems provide energy and power. And electrical, building covered more widely, the content of the system structure is more complicated. Modern architecture in the electrical system is no longer the only power supply, lighting, grounding, such as simple circuit, it is a use of electrical technology and electrical equipment, through the building space to create the sound, electricity, light, heat, wet, communication and management of the environment, to make it more suitable human life and the work of a comprehensive system.2 Fault diagnoses2.1 The definition of fault diagnosisFault diagnosis is in the continuous development of electronic technology and computer technology of a new technology. Refers to the system in a certain operating conditions to judge the running state and abnormal situation, and the abnormal state of separate parts, and find out the cause of the system function failure. Judge judging fault types at the same time, estimates the fault duration, forecasts the developmenttrend of fault state, and to provide the basis for system failure recovery.2.2 Methods of fault diagnosis and classificationDue to the fault diagnosis technology is based on electronic technology and computer technology, therefore, main show is in engineering with computers as the main body of the intelligent fault diagnosis system, it has three kinds of structure: stand-alone mode, distributed mode and network mode. Currently applied to intelligent fault diagnosis methods mainly include: the diagnosis method based on expert system, based on fuzzy logic diagnosis method, diagnosis method based on neural network, and the diagnosis method based on Multi - Agent, etc.3 The tradition of building electrical maintenance methodNowadays, the concept of building electrical has great development, while building electrical system in the intelligent approximately at the bottom, but it plays a vital role. Once the electrical system malfunction, light cause property damage, or threat to people's personal safety. Can, therefore, the failure occurs rapidly and accurately judge the reason, location and damage degree is very important. With the increasing of modern architectural features, building electrical system of large buildings have not only the power distribution system, including telecommunications, television, fire alarm, the data transmission and some remote monitoring of electrical equipment, and many other subsystems. These systems are connected to each other, and to make electrical system the possibility of failure multiplied. For building electrical failure after processing, at present it is still by means of artificial screening and maintenance. When unable to determine the exact cause of failure, in order to ensure promptly eliminate malfunction, maintenance personnel will all change, may lead to the fault line and device this way of troubleshooting for maintenance personnel's own experience and technology demand is higher, but also caused the increased cost of maintenance. Besides circuit and component aging caused by the failure, because of design changed randomly and non-standard construction procedures, also can cause hidden trouble to the electrical system, eventually leading to failure. Although intelligent fault detection technology in every industry has made considerable development, but the fault detection technology in the field of buildingelectrical rarely study. Investigate its reason, mainly because of building electrical belongs to the low voltage power distribution system, and at the end of the whole grid, neglected. Electrical fault diagnosis in the field of research, on the other hand, more concentrated in large electrical equipment, such as generator, transformer, etc., or the fault diagnosis of complex systems such as power grid, and building electrical systems because of its relatively simple structure, belongs to the engineering field, and therefore not be taken into account.4 The main content of building electrical systemsPower system refers to provide electric energy and transport, the use of electrical energy for the purpose of circuit and its related lines. The power system can also be referred to as the power supply or power transmission and distribution system. Transmission and distribution system is composed of transmission lines and substations and it has connected power plants and users, and provides electricity to the user directly. In building electric, the electric system usually refers to the 10 KV power distribution lines and substations under low voltage distribution network, it will power allocated to all types of users. And more than 10KV high voltage power supply network and power generation system, etc., are not within the scope of "building electric". Building electrical is divided into two most heavy current and weak current. High voltage part mainly includes distribution, dynamic lighting, lightning protection and grounding system, etc. Lightning protection grounding system mainly includes the grounding, lightning protection electricity, lightning protection waves intrusion, auxiliary equipotent connection, local equipotent connection and equipotent connection, etc. Weak current system is mainly used for the transmission of signals. Such as communication systems, public broadcasting system, fire linkage system, security monitoring system, cable TV system, etc. In addition, the modern building is also equipped with intelligent building systems, building all sorts of equipment through computer for unified control and management. In addition, as well as intelligent building systems, thanks to the rapid development of communication technology and automatic control technology, building is developing towards the trend of more and more intelligent. Intelligent building expands the function of thebuilding; improve the comfort and convenience to people in work and life. Building intelligent system will be independent of each other before building subsystem fuses in together, realize the real-time monitoring and remote control of building state. Intelligent building system adopts computer collecting and distributing control mode, namely "decentralized control, centralized management" model. Its controller is usually direct digital controller (DDC), management features carried by the upper machine and its software is responsible for the management, monitoring and management of the whole building. It is generally believed, building automation system, office automation system, security automation system, communication network automation system and fire linkage control system, etc., all belong to the category of intelligent building.5 The characteristics of residential building electrical systemResidential buildings are also known as the residence building. To live is to provide the family use buildings, including ordinary residential, hotel apartments, luxury villas, etc., belong to the category of civil buildings. Compared to residential buildings in industrial buildings and other large public and commercial buildings, the electric system structure is relatively simple, small electric equipment complexity., when the design requirements in compliance with the principles of security, practical, energy saving. Because its usage and function of residential building，electrical system also has its own characteristics and requirements.5.1 Residential load characteristicsElectricity at present stage is still the main body of social power, compared to the power industry. it has the characteristics of periodic peak. In the two periods in the morning and at night, there will be a peak season. During this time, people will use a lot of household electrical appliances and result in an increase in load. Therefore, to ensure that its load bearing capacity of the electrical system, to prevent it’s because of a certain "dot" trigger, lead to the collapse of the entire electrical system. In addition to fire power, emergency lighting, passenger lifts and life water pump load for a secondary load, other electricity are level 3 load.5.2 Distribution circuit design requirementsAccording to "residential building electrical design specification requirements, residential electricity capacity of less than 250KW, collective distribution can be set up. The lighting, electric power, fire and other disaster prevention electricity load should be distribution respectively. Indoor distribution box should be installed at the same time, disconnect phase line and neutral line into line switch, power supply circuit should be installed with short circuit and overload protection electric appliances, and furnish the residual current protective device. Due to some power distribution system in the design or installation quality cannot be guaranteed, can lead to "zero" break fault.” Break zero" refers to the three phases four wire systems, the neutral line N or protection line PEN disconnect or without conduction. If there is a "zero" broken when the three-phase unbalanced load, will appear the phenomenon of under voltage or over voltage, single-phase electric equipment will be damaged because of the voltage deviation is too large.译文建筑电气数据采集系统设计及故障诊断研究Fischer M摘要建筑电气作为建筑工程中不可或缺的一部分，承担着为建筑物提供能源、分配动力的作用。

建筑工程外文文献（含翻译）外文文献：Construction of the competition and competition strategy Engineering and construction firms from the United States dominated the global market for many decades but recent world events have altered their position.To investigate the driving forces and trends that will affect engineering and construction competition in the next decade, a research project, called the "Anatomy of Construction Competition in the Year 2000", was sponsored by the Construction Industry Institute's Construc-tion 2000 Task Force- The project examined the factors that affect competitiveness, including the following, The shaping of corporate capabilities; vertical integration and horizontal expansion to increase corporate capabilities and market share, including acquisition and mergers by offshore conglomerates and the acquisition of foreign firms by U. S. companies.Financing options; the role of privatization, build-own-transfer projects, and the nature of project financing in future markets, Management, organization, and structure; future management and organizational approaches, structures, and techniques to attract personnel to perform in a global competitive environment.Work force characteristics; future availability of engineering and construction workers at the professional and craft levels.Technological issues:how technology will affect competition and be used to offset work force shortages.Research Objectives and ScopeThis research project's goal is to collect information, to adaptto the 2000 and the engineering construction after adjustment, formulate strategies needed to provide insight and formulate 2000 engineering construction of possible development plan. This study reviewed the project construction process of history, current development trend, to determine the impact of the industry, and the impetus to the future industrial enterprises are related to reshape the ability, privatisation and financing methods of potential function and management, organization structure, methods for future development direction.Research scope includes selected some of the company, the company has interviewed expertise personnel. The staff professional wide range, including commercial buildings, public buildings, industrial infrastructure, infrastructure construction, power, light industry. The production process and space science. Engineering construction competitive characteristics Engineering construction of competition because the following reasons in change features:In the 1980s, and plan in the 1990s, the implementation of theproject construction are guided from contradictory situation, to cooperate.Should be in a positive view of the new company to enter the international market, because of its construction increased global cooperation opportunities. Cooperation will make all the partners, because the American company benefit can be found in the country partner, likewise, foreign companies opportunities will break into the U.S. Market.Competitive strategyFuture strategyIn 2000, the company will strive to do:Provide the highest quality serviceCan assume any part of the worldIn order to reduce the split ground and risk controlOut in international market the most competitive priceIn order to achieve the ideal, engineering construction should be: Increase staff capital investmentThe knowledge and improve labor technology levelHave solid complete communications and transport infrastructure Concentrate on key research, product quality is guaranteed, fine, and arouse the enthusiasm of the workers, improve workers technology level.The 21st century is the main factor fractal ring will compete in the international market, including the integration of productivity, union salary to abate, reduce the power industry management and privatization.American company competition ability, largely depends on developing and effective use of technical innovation. American companies need not only use the technical innovation, domestic by other countries optimization improved technology. In the future will be popular technology innovation will not some big breakthrough, but the existing technology continuous improvements.British buildings company profileIn the early 1990s, the head of the flexible builders who don't make a building, but what else can do, making many buildings company suffered a serious blow the economic depression, experienced and excessive expansion of real estate industry also. But, when he saw them in the real estate industry (in the big money, most of them in order to disencumber the bet down again in the real estate market. By Alan cosmas indicopleustesunder the leadership of Mr. Shaw ai enjoy in the old field company Merck's reputation can earn cash on the balance sheet, and can keep the balance. However, in some areas of the world, the company also man a dilemma, especially in the United States, the change from a Louisiana oil and natural gas market of recession, it is especially outstanding in Britain, the commercial and industrial real estate market, the company is faced with a difficult situation, with profits. And it also became worse. The company's development, walid UK early 1990s third big house builders, probably because London suburb will have a copy from the era of George sell buildings of former prime minister Margaret thatcher and world-famous. The company's character, chairman of the unique Laurie walid from Mr Often "give" iron lady public support. The approximate mythological blessing that he seemed destined to enjoy. In fact, the company also is different, the influence of the housing slump is strong in Laurie, under the leadership of the company now recover its stronger towards the financial status. Laurie retired charge again situation (1991 fall after his retirement he restored to the company recalled). As most of its business competitors, the industry in different market also suffered a serious blow, although the slump in 1993, the company is beginning to improve long-term credit rating IBCA institution of the first buildings company business development for a while. John, the company is different, have very good to withstand the latest world construction difficulties. They have abundant capital, clearly recognized that they have greatly reduced the book value of the asset. For example, in early 1990, they in real estate in the bank delimit lost 1 ￡2m value. After that, they cut and labor. Despite their housing sales still quite good, but its profit isreduced. The company is in most lai attention is famous for its environmental problems.The status and the tower mike company walid special form bright contrast, in 1993, their credit rating agency reduced by IBCA. This company in the 1980s most time trying to prove to the world that they are the UK's biggest builders, the information being understanding, and either, but hopefully it never happened. They suffer from cope with high growth rate cuts, to build houses. But the company is still tower mike Britain's biggest construction and building materials group company. October 1992, they closed the real estate business, and this is the will of the seven business to three (building, quarrying and residential building) part of the plan. Michael essien, Somerville, resistant to fly, the group's President, in the company after 22 years in the spring of 1992, sit on the seat of the hot ass. People think that the housing problem of exposure, this position has arrived at the point, which including several on a company's balance sheet of the large-scale joint enterprise, joint enterprise business, actually makes corporation debts machine more. T aylor wood of real estate industry recession Royce unpleasant experiences embodied in 1992, when the estate of autumn is DanielPeter HeJi sudden resignation, it also happens in its predecessor, Peter trillion resigned after all shocked by only a few months. Home, then reverse, Taylor wood Rolls-Royce announced due to bad management, caused severe losses. Although construction contracting business increasingly important status in a recession, but company two-thirds of income from this business is. However, the company has a huge investment assets securities, rental income more than 5 year 2000 million pounds. The company has no longer conduct riskybusiness projects, at least until the situation in better later.Eastern European architectural market competition situation analysisAt present, the economic reforms of the eastern Europe, thus caused confusion of these areas of business activities with the new economic system. Experts say, analyzed from a long-term perspective, using the market economic policy will bring a more stable, and more favorable economic environment. The reform of political economy in eastern Europe will be for those who are willing to invest in this area of the company to create a lot of money but market. If you keep the momentum, before long, eastern Europe 5640 billion dollars each year for the construction of international construction market will be more than one-third of the market. This area is open to the worldsituation inaugurated a new construction.The object of studyThe goal is to establish a framework, and international engineering and construction company may formulate feasible strategy, and to evaluate the. The framework has been introduced for the project construction company outside the eastern area in the construction business is very helpful. In order to measure the market opportunities and challenges, we sent the questionnaires and interviews, the individual to identify important success factors or aspects. Thus illustrates construction company in determining their strategy must possess the characteristics. Through the research of strategic framework has been set up in this area by an actual construction, an international engineering and construction company is considering to undertake the engineering, to test this strategic framework in specific market environment effect.The research methodsBy reference to the literature, questionnaire issued a personal interview, and the research target has been achieved. This research using data from the world's major construction company. Including 13 U.S. companies, two south Korean companies.Questionnaires to collect data compiled for investigation and ensure the consistency of the content. The problem, not the way people won't produce a certain criteria. Free to answer this question, ask questions in order to guarantee the unfavorable and overmuch. Participate in the company's answer to the question, questionnaire involving the problems in three aspects:(1) the eastern architecture market opportunities and challenges,(2) the construction of key factors YangChengGong city, (3) to determine the strategic framework, construction industry should make adjustments. Each main parts attached to a set of problems under which the object of study, make clear further.Interview based on construction engineering company voluntary under the condition of the study of the company, in answerThe telephone interviews survey or separate. For these companies how to build and use their own in this area is a strategic framework, if the researchers believe that the method is feasible, and they put main skills assembly written. By visiting personnel to answer questions, what is eastern architecture market success factor ? The important factor in his company is a positive or negative impact? What effect? Researchers also collected from international architectural engineering, as well as a lesson in later in the project of measures have been taken.The future trend of real estate investmentHousing has been the most important in the modern life of demand.Families with more spacious and comfortable housing demand has increased, and hope to have more disposable income in the house. As a result, households residential become very expensive. In addition, the new population statistics show that currently existing housing needs to sell the house of points, recreational property and retiree community. Commercial and industrial real estate investment is also very good. In order to judge what real estate market within the scope of comparative spruce, analyzed the market is very important. However, many investment prospects are very optimistic.The feasibility of the economy, the future of the investment real estate showing strong. But in general economic conditions, also do not exclude it "low" period. If investors can develop a safety strategy, so they will get considerable income. These strategies including effective operation and management, analyzes the problem, real estate and correct treatment, the contradiction between the owner and the occupiers and understand the role of investment and investment project, the influence of the government in property. The real estate investor can dominate the market this problem with real estate income has more than ordinary shares, the problem is an old problem. Actually no reason to believe that an investor can use the same market information and analytical skills in long-term operation can obtain excess profit. However, using internal message, data analysis and complex analysis method, so investors will probably make a better choice than its competitors. According to the real estate market, real estate investment process for investment and reduce costs "and" obtain goodresults provide the opportunity of investors.We know "lucky" or luck may produce short-term abnormal returns. We even have a few people because of good news to avoid "seek more expensive and succeed. Although a few of these people, they have intuition according to the real estate investment process. If you have the talent, don't study also to investment.The types of real estate investment in real estate investment is residence though relatively common form, and some properties of future investors have quite attractive. In each of the different fields during, and residential areas including real estate, commercial real estate, industrial real estate, agriculture, such as golf, and real estate and other special purposes. Although effective analysis skills necessary to investment projects with enlarged and complex and increasing, but the basic skills and real estate investment process remains unchanged.But the real income in accordance with the income level can rent levels and geographical location and according to the classification. The position of urban real estate value economic influence the effect of economic environment, so the analysis is very important. However, some places of the land clearly more suitable for specific purposes. For example, in the development of new urban residential area, the land may be too expensive, is not suitable for the development of low density garden project. Because it is so hard to use accurate way to predict future events, forecast and actual differences between the results may cause some serious problems. Overestimates rent rate or future price, low operation cost estimates, or to determine equipment renewal fee will cause serious cash flow problems. Fail to fulfill debt obligations or real estate tax lien may be compelledto cancel. All these things are closely related with investors.中文译文：建筑业的竞争及竞争策略美国的工程建筑公司几十年来一直控制着国际建筑市场，但近来世界上发生的事件改变了它的主导地位。

电气专业本科毕业设计英文翻译学院(部)：电气与信息工程学院专业班级：电气08-6班学生姓名：**指导教师：胡业林教授年月日POWER SUPPLY AND DISTRIBUTION SYSTEMABSTRACTThe basic function of the electric power system is to transport the electric power towards customers. The l0kV electric distribution net is a key point that connects the power supply with the electricity using on the industry, business and daily-life. For the electric power, allcostumers expect to pay the lowest price for the highest reliability, but don't consider that it's self-contradictory in the co-existence of economy and reliable.To improve the reliability of the power supply network, we must increase the investment cost of the network construction But, if the cost that improve the reliability of the network construction, but the investment on this kind of construction would be worthless if the reducing loss is on the power-off is less than the increasing investment on improving the reliability .Thus we find out a balance point to make the most economic,between the investment and the loss by calculating the investment on power net and the loss brought from power-off.KEYWARDS：power supply and distribution,power distribution reliability，reactive compensation,load distributionTEXTThe revolution of electric power system has brought a new big round construction,which is pushing the greater revolution of electric power technique along with the application of new technique and advanced equipment. Especially, the combination of the information technique and electric power technique, to great ex- tent, has improved reliability on electric quality and electric supply. The technical development decreases the cost on electric construction and drives innovation of electric network. On the basis of national and internatio- nal advanced electric knowledge, the dissertation introduces the research hotspot for present electric power sy- etem as following.Firstly, This dissertation introduces the building condition of distribution automation(DA), and brings forward two typical construction modes on DA construction, integrative mode and fission mode .It emphasize the DA structure under the condition of the fission mode and presents the system configuration, the main station scheme, the feeder scheme, the optimized communication scheme etc., which is for DA research reference.Secondly, as for the (DA) trouble measurement, position, isolation and resume, This dissertation analyzes the changes of pressure and current for line problem, gets math equation by educing phase short circuit and problem position under the condition of single-phase and works out equation and several parameter s U& , s I& and e I& table on problem . It brings out optimized isolation and resume plan, realizes auto isolation and network reconstruction, reduces the power off range and time and improves the reliability of electric power supply through problem self- diagnoses and self-analysis. It also introduces software flow and use for problem judgement and sets a model on network reconstruction and computer flow.Thirdly, electricity system state is estimated to be one of the key techniques in DA realization. The dissertation recommends the resolvent of bad measurement data and structure mistake on the ground of describing state estimate way. It also advances a practical test and judging way on topology mistake in state estimate about bad data test and abnormity in state estimate as well as the problem and effect on bad data from state measure to state estimate .As for real time monitor and control problem, the dissertation introduces a new way to solve them by electricity break and exceptional analysis, and the way has been tested in Weifang DA.Fourthly, about the difficulty for building the model of load forecasting, big parameter scatter limit and something concerned, the dissertation introduces some parameters, eg.weather factor, date type and social environment effect based on analysis of routine load forecasting and means. It presents the way for electricity load forecasting founded on neural network(ANN),which has been tested it’s validity by example and made to be good practical effect.Fifthly, concerning the lack of concordant wave on preve nting concordant wave and non-power compensation and non-continuity on compensation, there is a topology structure of PWM main circuit and nonpower theory on active filter the waves technique and builds flat proof on the ground of Saber Designer and proves to be practical. Meanwhile, it analyzes and designs the way of non-power need of electric network tre- nds and decreasing line loss combined with DA, which have been tested its objective economic benefit throu- gh counting example.Sixthly, not only do the dissertation design a way founded on the magrginal electric price fitted to our present national electric power market with regards to future trends of electric power market in China and fair trade under the government surveillance, that is group competitio n in short-term trade under the way of grouped price and quantity harmony, but also puts forward combination arithmetic, math model of trading plan and safty economical restriction. It can solve the original contradiction between medium and long term contract price and short term competitive price with improvement on competitive percentage and cut down the unfair income difference of electric factory, at the same time, it can optimize the electric limit for all electric factories and reduce the total purchase charge of electric power from burthen curve of whole electric market network.The distribution network is an important link among the power system. Its neutral grounding mode and operation connects security and stability of the power system directly. At the same time, the problem about neutral grounding is associated with national conditions, natural environment, device fabrication and operation. For example, the activity situation of the thunder and lightning, insulating structure and the peripheral interference will influence the choice of neutral grounding mode Conversely, neutral grounding mode affects design, operation, debugs and developing. Generally in the system higher in grade in the voltage, the insulating expenses account for more sizable proportion at the total price of the equipment. It is very remarkable to bring the economic benefits by reducing the insulating level. Usually such system adopt the neutral directly grounding and adopt the autoreclosing to guarantee power supply reliability. On the contrary, the system which is lower in the voltage adopts neutral none grounding to raise power supply reliability. So it is an important subject to make use of new- type earth device to apply tothe distribution network under considering the situation in such factors of various fields as power supply reliability, safety factor, over-voltage factor, the choice of relay protection, investment cost, etc.The main work of this paper is to research and choice the neutral grounding mode of the l0kV distribution network. The neutral grounding mode of the l0kV network mainly adopts none grounding, grounding by arc suppressing coil, grounding by reactance grounding and directly grounding. The best grounding mode is confirmed through the technology comparison. It can help the network run in safety and limit the earth electric arc by using auto-tracking compensate device and using the line protection with the detection of the sensitive small ground current. The paper introduces and analyzes the characteristic of all kind of grounding modes about l0kV network at first. With the comparison with technological and economy, the conclusion is drawn that the improved arc suppressing coil grounding mode shows a very big development potential.Then, this paper researches and introduces some operation characteristics of the arc suppressing coil grounding mode of the l0kV distribution network. And then the paper put emphasis on how to extinguish the earth electric arc effectively by utilizing the resonance principle. This paper combines the development of domestic and international technology and innovative achievement, and introduces the computer earth protection and autotracking compensate device. It proves that the improved arc suppressing coil grounding mode have better operation characteristics in power supply reliability, personal security, security of equipment and interference of communication. The application of the arc suppressing coil grounding mode is also researched in this paper.Finally, the paper summarizes this topic research. As a result of the domination of the arc suppressing coil grounding mode, it should be more popularized and applied in the distribution network in the future.The way of thinking, project and conclusions in this thesis have effect on the research to choose the neutral grounding mode not only in I0kV distribution network but also in other power system..The basic function of the electric power system is to transport the electric power towards customers. The l0kV electric distribution net is a key point that connects the power supply with the electricity using on the industry, business and daily-life. For the electric power, all costumers expect to pay the lowest price for the highest reliability, but don't consider that it's self-contradictory in the co-existence of economy and reliable. To improve the reliability of the power supply network, we must increase the investment cost of the network con- struction But, if the cost that improve the reliability of the networkconstruction, but the investment on this kind of construction would be worthless if the reducing loss is on the power-off is less than the increasing investment on improving the reliability .Thus we find out a balance point to make the most economic, between the investment and the loss by calculating the investment on power net and the loss brought from power-off. The thesis analyses on the economic and the reliable of the various line modes, according to the characteristics various line modes existed in the electric distribution net in foshan..First, the thesis introduces as the different line modes in the l0kV electric distribution net and in some foreign countries. Making it clear tow to conduct analyzing on the line mode of the electric distribution net, and telling us how important and necessary that analyses are.Second, it turns to the necessity of calculating the number of optimization subsection, elaborating how it influences on the economy and reliability. Then by building up the calculation mode of the number of optimization subsection it introduces different power supply projects on the different line modes in brief. Third, it carries on the calculation and analyses towards the reliability and economy of the different line modes of electric distribution net, describing drafts according by the calculation. Then it makes analysis and discussion on the number of optimization subsection.At last, the article make conclusion on the economy and reliability of different line modes, as well as, its application situation. Accordion to the actual circumstance, the thesis puts forward the beneficial suggestion on the programming and construction of the l0kV electric distribution net in all areas in foshan. Providing the basic theories and beneficial guideline for the programming design of the lOkV electric distribution net and building up a solid net, reasonable layout, qualified safe and efficiently-worked electric distribution net.References[1] Wencheng Su. Factories power supply [M]. Machinery Industry Publishing House. 1999.9[2] Jiecai Liu. Factories power supply design guidance [M]. Machinery Industry Publishing House.1999.12[3] Power supply and distribution system design specifications[S].China plans Press. 1996[4] Low-voltage distribution design specifications [S].China plans Press. 1996.6供配电系统摘要电力系统的基本功能是向用户输送电能。

一个非线性电谐振器作为一个简单的触摸感应开关与记忆存储器摘要我们介绍了一个新的切换机构，它依赖于一个简单的非线性电谐振器，其中包括一个变容二极管作为其电容元件的双稳态的切换动作，开关动作可以快速和自包含在电路中。

不同于一个触发器的翻转，其状态是通过施加一个TTL脉冲翻转，这种非线性开关可以通过磁，电感性或电容性耦合被接合到外部电路，在这种方式中，开关变为本质触摸敏感。

另外，开关动作也可以使用频移键控（FSK）调制，实现有记忆状态的快速操作的承诺。

我们通过构建一个触摸感应的LED 点阵证明这些想法的潜在应用。

关键词：非线性开关;电气谐振器的双稳态特性;触摸灵敏度1.介绍在数字电子技术，可以在两个状态之间进行切换的典型的存储元件，当然是触发器。

SR触发器无处不在，例如，它包含两个交叉的NOR（或NAND）门。

当无信号时，触发器的状态保持在其以前的配置，并以它翻转到另一种状态的简要电压信号（TTL脉冲）被施加到相应的输入。

在这里，我们提出了一个非线性电谐振器，在某些方面的作用就像一个触发器。

正如我们表明，它的两个状态之间的切换是通过驱动频率协议（FSK调制）来实现，或通过将一个磁铁或到附近的谐振器的电感器来完成的，它也可以通过电容耦合被切换。

设置完成后，系统会记住它的状态，直到另一个开关动作。

然而，不像一般的触发器，该元件可被诱导以从电路的外面进行切换。

另外，频率调制方案可以快速切换。

最后，我们将通过构建一个可控的LED阵列展示这一理念的应用程序。

由于开关动作可以出现在响应触摸（通过改变电容）或靠近磁铁或电感器，这种谐振就像触摸感应开关，这也许会让人联想到一个“触摸灯”。

当这种灯的金属外壳被触摸时，它的有效电容增加。

有那么多的方式来电容转换为数字输出[1]。

即使是最简单的方案采用了数字集成电路元件：一个固定幅度的交流电压驱动器充电和放电的住房，并在接触充电电流增加，进一步电路检测这种增强的电流和开关一个触发器。