打印机设置与使用说明书

Read these instructions before using your product.

1 Unpack

Note: Do not open the ink cartridge package until you are ready to install the ink. Cartridges are vacuum packed to maintain reliability.

Remove all protective materials from the product.

Caution: Do not touch the flat white cable.

2 Turn on and configure

1 Connect the AC adapter to the back of the product. Then

connect one end of the power cord to the AC adapter and

the other end to an electrical outlet.

Caution: Do not connect to your computer yet.2 Move the handle behind the printer, lower the output tray, and open the printer cover.

3 Raise the control panel and turn on the product.

Note: If an error message appears, turn off the product and check that no protective material has been left inside the product.

4 Press or to select your language, then press the OK

button.

Note: You can change the language later using the product’s control panel. For more information, see the online User’s Guide.

3 Install ink cartridge

Caution: Keep ink cartridges out of the reach of children and don’t drink the ink.

1 Unpack the initial ink cartridge and completely remove the

yellow tape only.

Caution: Do not remove any other labels or seals, or ink may leak.

2 R

emove the plastic base and carefully dispose of it.

4 Load paper

1 Open the rear paper feed cover if necessary. Flip the

feeder guard forward and slide the edge guide to the right.

2 Load 4 x 6 or 5 x 7-inch photo paper, glossy or printable

side up and short edge first, against the left side.

3 Slide the edge guide against the paper, but not too tightly,

and flip the feeder guard back.

4 Press or to select Change on the LCD screen and

press the OK button.

5 Select your paper size and press the OK button.

6 Select your paper type and press the OK button.

7 Press the OK button again to confirm the paper settings.

Note: Make sure the paper settings matches the type and size of paper you loaded.Caution: Do not touch the areas on the ink cartridge shown below. Doing so may prevent normal operation and printing.

Warning: If ink gets on your skin, wash it thoroughly with soap and water. If ink gets into your eyes, flush them immediately with water. If ink gets into your mouth, spit it out and see a doctor right away.

3 Hold the cartridge with the green chip facing you and

insert the cartridge at an angle as shown. Press down the

ink cartridge until it clicks into place.

Caution: Make sure to insert the ink cartridge in the correct

direction or you may damage the product.

4 Close the printer cover.

5 Press the button to start charging the ink.

Ink charging takes a few minutes. Ink charging is

complete when you see the home screen displayed on the

LCD screen.

Caution: Do not turn off the product or open the printer cover while the product is charging or you’ll waste ink.

Note:

• The printer is designed for use with Epson® cartridges only, not third-party cartridges or ink.

• The cartridge included with the printer is designed for printer set up and not for resale. After some ink is used for charging, the rest is available for printing.

• If the screen is dark, the product has entered sleep mode. Press any button on the control panel to wake the product. You can adjust the sleep timer later if necessary. For details, see the online User’s Guide.Computer setup

Follow the steps here to connect your product to a computer

or wireless network.

Note: If your computer does not have a CD/DVD drive or you are using a Mac, an Internet connection is required to obtain the product software. To print from a Chromebook™, go to www.epson.com.jm/support/gcp for instructions.

1 Make sure the product is NOT CONNECTED to your computer.

Windows®: If you see a Found New Hardware screen, click Cancel and disconnect the USB cable.

2 Insert the product CD or download and run your product’s

software package:

www.epson.com.jm/support/pm525

3 Follow the instructions on the screen to run the setup

program.

4 When you see the Select Your Connection screen, select

one of the following:

• Wireless connection

In most cases, the software installer automatically

attempts to set up your wireless connection. If setup

is unsuccessful, you may need to enter your network

name (SSID) and password.

• Direct USB connection

Make sure you have a USB cable (not included) ready.

Mobile printing options

Connect wirelessly from your smartphone, tablet, or computer.

Print documents and photos from across the room or around

the world:

• Print directly from your iPhone, iPad, or iPod touch. Simply

connect your printer and device to the same network and

tap the action icon to select the print option.

• Use Epson Print Enabler (free from Google Play™) with