206= 5mm 6 chip
200= 5mm 1 chip
Double Contact Type Miniature BaseLED Lamps
28V
L
o
g
#
0
3
6
B
R
e
v
3
-
9
9
LED Lens
Type
LED/Chip
Brightness Code
Standard Operating
Voltage
(Examples)
Polarity
(Examples)
BP = Bipolar
AC/DC
AC = AC Only
Electrical
Characteristics
Options
Color Code
元器件交易网www.cecb2b.com
123Request for your special attention and precautions in using the technical information andsemiconductors described in this book(1)If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws andregulations of the exporting country, especially, those with regard to security export control, must be observed. (2)The technical information described in this book is intended only to show the main characteristics and application circuit examplesof the products, and no license is granted under any intellectual property right or other right owned by our company or any other company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other company which may arise as a result of the use of technical information described in this book.(3)The products described in this book are intended to be used for standard applications or general electronic equipment (such as officeequipment, communications equipment, measuring instruments and household appliances). Consult our sales staff in advance for information on the following applications:– Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the prod-ucts may directly jeopardize life or harm the human body.– Any applications other than the standard applications intended.(4)The products and product specifications described in this book are subject to change without notice for modification and/or im-provement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to make sure that the latest specifications satisfy your requirements. (5)When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions(operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any defect which may arise later in your equipment.Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products.(6)Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS,thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages.(7)This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of MatsushitaElectric Industrial Co., Ltd.M a i n t e n a n D i s c o n t i n u eP le a s ev i s it f o l l o w i n g U R L a b o u t l a t e s t i n fo r mh t t p ://p a n a s o n i c .n e t /s c /e n。
Forced Current Sharing Series AC/DC Switching Power SupplyFEATURES● 2 Year Warranty● N+1 Active Current Sharing ● Optional Top Cover Available ● Universal AC Input / Full Range● Peak Power 900W within 500uS duty duration ● Power Factor Corrected to EN61000-3-2 Class D ● High Power Density (Max. 9.1 Watts per cubic inch) ● Approved to UL/CUL/TUV/CB/CE & Class B Emissions ● U-Chassis & Enclosed with Built-in Fan Mechanical OptionsSPECIFICATIONS: PSRL5017R6-I SeriesAll specifications are based on 25oC, Nominal Input Voltage, and Maximum Output Current unless otherwise noted.We reserve the right to change specifications based on technological advances.INPUT SPECIFICATIONS Input Voltage 90 - 264 VAC Full Range (PSRL5017Rx8-I 800W Series: 180 - 264 VAC only). Input Current 10A at 90VAC and full load. Input Frequency 47 to 63Hz Inrush Current 70A max. @ 230VAC with full load cold start. Leakage Current 3.5mA max. @ 240VAC. Remote ON/OFF Designated as RSW on CN3, requires a low signal to inhibit output. OUTPUT SPECIFICATIONS Output Voltage See Table Output Power Range 600 Watts max with airflow. (See Note 3) Output Adjustability Output user adjustable ±5% minimum. Total Regulation ±1% Output Current See Table Ripple & Noise (peak to peak) See Table Transient Response Returns to within 1% in less than 2.5ms for a 50% load change and the peak transient does not excess 5%. Hold-Up Time 20ms min. at 80% of full load. Overshoot Turn-On & Off overshoot < 5% over nominal voltage. Turn On Delay 1 second maximum at 120VAC. PROTECTIONOver Voltage Protection Unit latching down when output voltage exceeds 130% and recycle AC input to reset. Short Circuit Protection Trip without damage and auto-recovery. Over-Temperature Protection Unit protected of excessive operating ambient 85°C and automatic recovery. Over-Power Protection Fold back mode 110-140% and auto-recovery. Input Voltage Protection Power shut down under 80 ±5VAC, and recovered over 86VAC Input Fusing Protection A T10A/250V fuse inserted in primary. GENERAL SPECIFICATIONS Efficiency 70% for 3.3V, 75% for 5V, 80% for 12V, and 83% minimum for other outputs @ 230VAC and full load.Withstand Voltage1500 VAC input line to chassis (10mA DC cut off current); 3000VAC between primary and secondarywindings. Primary to core 1500VAC. All for 3 seconds.Burn In 45 ±5°C for one hour @ 230VAC with full load. PFC Active power factor correction meets EN61000-3-2 class D.Power GoodDesignated as PG on the CN3 and TTL high 100-500ms after regulation. It goes low at least 1ms before lossof regulation for Power on Reset signal.Grounding Test Apply 25A from ground pin of the three prong plug to the far most earth. Max allowable resistance is 0.1 ohm.U Type: (U-Chassis): 8(L) x 4.33(W) x 2.5(H) inchesE Type: (Enclosed with built-in Fan): 9.17(L) x 4.25(W) x 2.5(H) inchesForced Current Sharing SeriesAC/DC Switching Power Supply SPECIFICATIONS (CONTINUED)GENERAL SPECIFICATIONS (CONTINUED)Current Sharing Designated as CSH on the CN3, optional single wired for forced current sharing function and parallel up to 4 units within 10% accuracy at full load.Current Monitor Designated as CMN on the CN3 is a 0.5V to 3VDC output voltage to represent 0% to 100% output current.LED Display Bi-color LED1 emit Green for Power On and emit Orange when protection is enabled or RSW is applied a low signal.ENVIRONMENTAL SPECIFICATIONSOperating Temperature 0°C to +70°C ambient, de-rating at 2.5% per degree from 50°C to 70°C. Storage Temperature -20°C to +85°COperating Humidity 5% to 90% RH, non-condensingStorage Humidity 5% to 95% RH, non-condensingVibration 5 ~ 50Hz, acceleration 7.35 m/(s x s) on X, Y, and Z axis.Cooling U Type (U-Chassis): 30CFM to achieve maximum power for all models except PSRL5017R3-I Series which is convection cooled.E Type (Enclosed with built-in fan): Self cooled by built-in fan.MTBF 150,000 hours (according to MIL-HBK-217F) at 30°C. PHYSICAL SPECIFICATIONSWeight U Type (U-Chassis): 1350 gramsE Type (Enclosed with built-in fan): 1450 gramsDimensions U Type (U-Chassis): 8(L) x 4.33(W) x 2.5(H) inches.E Type (Enclosed with built-in fan):9.17(L) x 4.25(W) x 2.5(H) inches.Warranty 2 yearsSAFETYEmissions FCC part15, CISPR 22 Class B, Conducted.Safety Regulations Approved to UL60950-1, CSA C22.2 No. 60950-1-03, TUV EN60950-1, CE Mark (LVD) EN61000-3-2,3, and IEC61000-4 Series Regulations and CB.OUTPUT VOLTAGE / CURRENT RATING CHARTModel Output VoltageRangePresetVoltageOutputCurrentRegulation Ripple & Noise Output PowerPSRL5017Rx6-03I 2 – 3.3 VDC 3.3 VDC 90A ±1% 75mV 297W PSRL5017Rx6-05I 5 – 6 VDC 5 VDC 90A ±1% 75mV 450W PSRL5017Rx6-12I12 – 15 VDC 12 VDC 50A ±1% ±1% 600W PSRL5017Rx6-16I16 – 21 VDC 18 VDC 37.5A ±1% ±1% 600W PSRL5017Rx6-24I22 – 30 VDC 24 VDC 27.27A ±1% ±1% 600W PSRL5017Rx6-36I31 – 47 VDC 36 VDC 19.35A ±1% ±1% 600W PSRL5017Rx6-48I48 – 56 VDC 48 VDC 12.5A ±1% ±1% 600W NOTES1. The PSRL5017R6-I Series is designated as PSRL5017Rxy-z where x = U (U-chassis type) or E (Enclosed with built-in fan type),y = 6 for output power from 297W - 600W, and z = 03I, 05I, 12I, 16I, 24I, 36I, or 48I for output voltage (I denotes forced current sharing (output with internal OR-ring diode)).2. All output ranges are covered in agency certifications and preset voltage will be set as standard models. If any request is not preset output, then please contact us in advance.3. U-Chassis type needs external forced airflow min. 30CFM to achieve maximum power, except PSRL5017RU3-z which is convection cooled.4. Ripple & noise are measured from 10KHZ to 20MHz bandwidth at output with parallel 0.1uF ceramic and 22uF electrolytic capacitors.5. Providing peak power to 900W within 500uS for all models, longer duty duration need contact manufacturer.6. 1% minimum load is required to maintain the ripple and regulation.7. Cover is optional for U-Chassis Type. Please call factory for ordering details.8. Output is fully isolated.Forced Current Sharing Series AC/DC Switching Power SupplyMECHANICAL DRAWINGSPSRL5017RU6-I Series (U-Chassis Type): 8(L) x 4.33(W) x 2.5(H) inches; Weight: 1350g; Option: Top Cover.PSRL5017RE6-I Series (Enclosed with built-in Fan Type): 9.17(L) x 4.25(W) x 2.5(H) inches; Weight: 1450g.I/O CONNECTOR PIN ASSIGNMENTAC Input Connector (CN1):Enclosed Type: IEC320 or equivalent Snap-in mounting type or DINKLE Terminal block Part No. DT-35-A02W-03 (3 pin).U-Chassis Type: Mating Molex Part No. 09-91-0700 or equivalent (7 pin. 5 used) or Howder Terminal block Part No. HD-121-3P.Output Connector (CN2):Mating Molex Part No. 09-91-2000 (20 pin) or Howder Terminal block Part No. HD-121-8P (8 pin).Output Pin Assignment: (See table at right)Logic signal connectors (CN3):Mating JST XHP-7 or equivalent (CHYAO SHIUNN JS-2001-07).Fan Drive: 12VDC/500mA Mating JST XHP-2 or equivalent (CHYAO SHIUNN JS-2001-02).Mounting Inserts: 6-32, M4 4 Places individually with maximum penetration 0.2 inch on bottom side and 0.25 inch on both sides.Output Pin Connection Howder Molex Vo+ Pins 1 – 4 Pins 1 – 10Vo-Pins 5 – 8Pins 11 – 20。
