压力容器专业部分英语词汇压力容器常用术语缩写1.检验检测术语（1）MET——力学性能试验（2）CT——化学成分分析（3）NDT——无损检测（4）DT——尺寸检查（5）VT——外观检查（6）RT——射线检测（7）UT——超声检测（8）MT——磁粉检测（9）PT——渗透检测（10）HB——布氏硬度（11）HV——维氏硬度（12）HR——洛氏硬度（13）HL——里氏硬度2.热处理术语（1）NT——正火＋回火热处理（2）ISR——中间消除应力热处理（3）PWHT——焊后热处理（4）MAX.PWHT——可能达到的最大程度焊后热处理（5）MIN.PWHT——可能达到的最小程度焊后热处理（6）DHT——消氢处理（7）S.C——分步冷却脆化热处理ASME常用词汇Abrasion, allowance for 磨损，裕量Accessibility，pressure vessels 压力容器可达性Access openings 通道孔Allowance for corrosion, erosion, or abrasion 腐蚀裕量侵蚀或/磨损裕量Applied linings, tightness 应用衬里密封性Approval of new materials 新材料的批准Articles in Section V 第V卷中的各章Article 1, T-150 第1章T150Article 2 第2章Attachments 附件lugs and fitting 支耳和配件lugs for platforms, ladders, etc. 平台，梯子等的支耳nonpressure parts 非受压件nozzles 接管pipe and nozzle necks to vessel walls 在器壁上的管子和接管颈stiffening rings to shell 壳体上的刚性环Backing strip垫板Bending stress, welded joints弯曲应力，焊接接头Bend test弯曲试验Blind flanges盲板法兰Bolted flange connections螺栓法兰连接bolt lands 螺栓载荷bolt stress 螺栓应力design of 关于设计flange moments 法兰力矩flange stresses 法兰应力materials 材料studs 双头螺栓tightness of 紧密性types of attachment 附件类型Bolts 螺栓Braced and stayed surfaces 支持和支撑面Brazed connections for nozzles 接管的钎焊连接Brazed joints, efficiency of 钎焊接头，焊缝系数maximum service temperature 最高使用温度strength of 强度Brazing, cleaning of brazed surfaces 钎焊，钎焊的表面清理fabrication by用……制造filler metal 填充金属fluxes 钎焊剂heads into shells 封头接入壳体operating temperature 操作温度Buttstraps, curvature 对接盖板，曲率forming ends of 成型端thickness and corrosion allowance 厚度和腐蚀裕量welding ends of 焊接端Carbon in material for welding 焊接用材料中的碳Cast ductile iron vessels, design 可锻铸铁容器，设计pressure-temperature limitations 压力-温度界限service restrictions 使用限制Castings 铸件carbon steel 碳钢defects 缺陷impact test 冲击试验inspection 检查quality factor 质量系数specifications 标准Cast iron circular dished heads 铸铁碟形封头Cast iron standard parts, small 铸铁标准部件，小件Cast iron pipe fittings 铸铁管件Cast iron vessels 铸铁容器corners and fillets 圆角和倒角head design 封头设计hydrostatic test 水压试验nozzles and fittings 接管和配件pressure-temperatures limitations 压力-温度界限Certificate of Authorization for Code Symbol Stamp 规范符号标志的认可证书Certification of material 材料证明书Certification of Nondestructive Personnel 无损检验人员证明书Magnetic Particle Examination 磁粉检验Liquid Penetrant Examination液体渗透检验Radiographic Examination 射线超声检验Ultrasonic Examination 超声检验Chip marks on integrally forged vessels 整体锻造容器上的缺口标志Circumferential joints alignment tolerance环向连接，组对公差assembling装配brazing钎焊vessels subjected to external pressure 承受外压的容器Clad material, inserted strips 覆层材料，嵌条examination 检查Clad plate 复合板Cleaning ,of brazed surfaces 钎焊表面清理of welded surfaces 焊接表面Clearance between surfaces to be brazed 钎焊表面间的间隙Combination, of different materials 不同材料组合of methods of fabrication制造方法Computed working pressure from hydrostatic tests 由水试验计算的工作压力Conical heads 锥形封头Conical sections 圆锥截面Connections ,bolted flange (see Bolted flange connections)连接，螺栓法兰（见螺栓法兰连接）brazed 钎焊clamp 卡箍expanded 胀接from vessels to safety valves 由容器至安全阀studded 双头螺栓threaded 螺纹welded 焊接Cooling, after postweld heat treating冷却，焊后热处理Corrosion allowance腐蚀裕度Corrosion resistant linings防腐蚀衬里Corrugated shells波纹形壳体Corrugating Paper Machinery 波纹板机械Cover plates 盖板on manholes and handholes 在人孔和手孔上的spherically dished 球形封头Cracking, stress corrosion 应力腐蚀裂缝Cutting plates 板材切割Cylindrical shells, supplementary loading 柱状壳体，附加载荷thickness 厚度transition in 过渡段Data report, guide for preparation 准备数据报告的指南Defects in welded vessels, repair 修理焊接容器中的缺陷Definitions定义Design, brazed vessels 设计钎焊容器carbon and low alloy steel vessels 碳钢及低合金钢容器cast ductile iron vessels 可锻铸铁容器cast iron vessels 铸铁容器clad vessels 覆层容器ferritic steel vessels with properuts enhanced by heat treatment 经热处理后提高抗拉性能的铁素体钢容器forged vessels 锻造容器high-alloy steel vessels 高合金钢容器loadings 载荷multichamber vessels 多受压室容器nonferrous vessels 非铁金属容器welded vessels 焊接容器design pressure 设计压力Diameter exemption 直径的豁免Dimensions, checking of 尺寸，校核Discharge of safety valves 安全阀泄放Dished heads (see formed heads) 碟形封头(见成形封头)Disks, rupture 防爆膜Dissimilar weld metal 不同金属的焊接Distortion, of welded vessels 大变形、焊接容器supports to prevent 用支撑防止Drainage, discharge from safety and relief valves 排放，由安全阀和泄压阀泄放Drop weight tests 落锤试验Eccentricity of shells 壳体的偏心度Edges of plates, metal removal from 由加工板边去除金属tapered 锥度Efficiency, around openings for welded attachments 焊缝系数，环绕焊接附件孔口Elasticity, modulus of 弹性模量Electric resistance welding 电阻焊Ellipsoidal heads 椭圆封头Erosion, allowance for 侵蚀裕量Etching, of sectioned speciments 侵蚀，关于截面试样solutions for examination for materials 检验材料的溶液Evaporators 蒸发器Examination, of sectioned speciments 剖面试样的检验of welded joints 焊接接头的检验Exemptions diameter and volume 直径和容积的豁免Expanded connections 胀接连接External pressure, tube and pipe 外压管External pressure vessels 外压容器allowable working pressure for 许用工作压力charts 算图design of heads for 封头设计joints in shells of 壳体上的接头reinforcement for openings 开孔补强stiffening rings in shells 壳体上的刚性环supports for 支承thickness of shell 壳体厚度reducers 变径段Fabrication, brazed vessels 制造，钎焊容器Ferritic steels vessels with tensile properties enhanced by heat treatment, design经热处理后提高抗拉性能的铁素体钢容器，设计fabrication 制造head design 封头设计heat treatment热处理heat treatment verification tests 热处理验证试验marking 标志materials 材料stamping 标记welded joints 焊接接头Field assembly of vessels 容器的现场安装Filler plugs for trepanned holes 锥孔的管塞Fillet welds 角焊Fired process tubular heaters 直接火管式加热炉Fitting attachments 附件装配Flange connections 法兰连接Flange contact facings 法兰接触面Flanges 法兰bolted design 螺柱法兰设计of formed heads for welding 用于焊接成型封头type of attachment 附件的类型Flat heads and covers, unstayed 无支撑平封头和盖板reinforcement of openings 开孔补强Flat spots on formed heads 成型封头上的平坦部分Flued openings 翻边开孔Forged parts, small 锻造部件，小的Forged vessels 锻造容器heat treatment 热处理localized thin areas 局部薄壁区welding 焊接Forgings 锻件identification of 识别Ultrasonic Examination 超声检验Form manufacturer’s data report 制造厂数据报告格式partial report 零部件数据报告Formed heads 成型封头flued openings in 封头上翻边开孔insertion of, welded vessels 插入，焊接容器joint efficiency 接头系数knuckle radius 转角半径length of skirt 直边长度on welded vessels 在焊接容器上reinforcement for openings 开孔补强Forming 成型ends of shell plates and buttstraps 壳体板和对接搭板端forged heads 锻造封头shell sections and heads 筒节和封头Furnaces 炉子temperatures for postweld head treatment 焊后热处理温度Furnaces for heat treating 热处理炉temperature control of 炉温控制Galvanized vessels 镀锌容器Gasket materials 垫片材料Girth joints (see circumferential joints) 环缝接头(见环向接头)Handhole and manhole openings 手孔和人孔开孔Head flange (skirt) length 封头翻边(直边)长度Head joints 封头接头brazing 钎焊welded 焊接Head openings 封头开孔entirely in spherical portion 全部在球体部分Head joints 封头接头concave and convex 凹面和凸面flat (see flat heads) 平板(见平封头)forged 锻造的formed (see Formed heads) 成型的(见成形封头)forming 面型thickness, after forming 厚度，成型之后Heads, design, conical 封头，设计，锥形ellipsoidal 椭圆形hemispherical 半球形spherically dished 球状碟形toriconical 带折边的锥形torispherical 带折边的球形torispherical, knuckle radius 带折边的球形，转角半径Heads and shells 封头和壳体external pressure, out-of-roundness 外压，不圆度openings through or near welded joints 通过或靠近焊缝处的开孔roundness tolerance 不圆度公差Heat exchangers 热交换器Heat treatment 热处理by fabricator 由制造厂进行carbon and low-alloy steel vessels 碳钢和低合金钢容器ferritic steel vessels with tensile properties enhanced by heat treatment 经过热处理后提高抗拉性能的铁素体的容器forged vessels 锻造容器furnaces 炉子high-alloy vessels 高合金容器of test specimens 试样的热处理verification tests of 热处理验证试验Hemispherical heads 半球形封头High pressure vessels 高压封头Holes 小孔for screw stays 用于螺丝固定for trepanning plug sections, refilling 用于穿孔螺塞部分，再填充telltale 指示孔unreinforced, in welded joints 不补强，在焊缝上Hubs, on flanges 高颈，在法兰上Hydrostatic proof tests 水压验证试验destructive 破坏性prior pressure application 在升压之前Hydrostatic test 水压试验cast iron vessels 铸铁容器combined with pneumatic 与气压试验混合的enameled vessels 搪玻璃容器external pressure vessels 外压容器galvanized vessels 镀锌容器standard 标准welded vessels 焊接容器Identification 识别of forging 锻件of plates 平板of welds 焊接Identification markers, radiographs 识别标志，射线照相Impact test 冲击试验certification 证明properties 性能specimens 试样temperature 温度Inspection 检查before assembling 组装之前carbon and low-alloy steel 碳钢和低合金钢cast ductile iron vessels 可锻铸铁容器cast iron vessels 铸铁容器clad vessels 覆层容器during fabrication 在制造期间ferritic steel vessels with tensile properties enhanced by heat treatment 经过热处理后提高抗拉性能的铁素体的容器fitting up 组对forged vessels 锻造容器heat treatment, forgings 热处理，锻件high-alloy steel vessels 高合金钢容器magnetic particle 磁粉material 材料nonferrous vessels 非铁金属容器plate 板材postweld heat treatment 焊后热处理pressure vessels, accessibility 压力容器，可达性quality control 质量管理sectioning of welded joints 焊接接头的剖面检验spot examination 抽样检查steel castings 铸钢件surfaces exposed and component parts 暴露的表面和元件部分test specimens 试样vessels 容器vessels exempted from 免检容器welded vessels 焊接容器Inspection openings 检查孔Inspectors 检查师access to plant 在厂内应有的便利control of stamping 打印管理duties 职责facilities 装备qualification 资格reports 报告Installation 安装pressure-relieving devices 泄压装置pressure vessel 压力容器Integral cast iron dished heads 整体铸铁碟形封头integrally finned tubes 整体翅片管Internal structures 内部构件Jacketed vessels 夹套容器Joints 接头brazed 钎焊circumferential (see Circumferential joints) efficiency, brazed 环缝(见环向接头)系数，钎焊welded 焊接electric resistance, butt welding 电阻，对接焊in cladding and applied linings 在覆层及衬里in vessels subjected to external pressure 在承受外压的容器lap (see Lap joints) 搭接(见搭接接头) longitudinal (see Longitudinal joints) 纵向(见纵向接头)tube-to-tubesheet 管子对管板Jurisdictional Review 权限审查Knuckles 过渡圆角radius 半径transition section 变径段Lap joints 搭接接头amount of overlap 搭接量brazed 钎焊longitudinal under external pressure 在外压作用下纵向的welded 焊接Laws Covering Pressure Vessels 涉及压力容器的法规Lethal gases or liquids 致命的气体或液体Ligaments, efficiency of 孔带，系数Limitation on welded vessels 焊接容器的限制Limit of out-of-roundness of shells 壳体不圆度的限制Linings 衬里corrosion resistant 抗腐蚀Liquid penetrant examination 液体渗透检验Loadings 载荷Local postweld heat treatment 局部焊后热处理Longitudinal joints 纵向接头alignment tolerance 对准公差brazing 钎焊vessels subjected to external pressure 承受外压的容器Low-temperature operation 低温操作Low-temperature vessels brazed 低温容器，钎焊for gases and liquids 用于气体和液体impact test requirements 冲击试验要求impact test, when not required 冲击试验，当不要求时marking 标志materials 材料testing of materials 材料试验Lugs for ladders, platforms, and other 梯子，平台及其它附件的支耳Magnetic particle inspection 磁粉检查Manholes, and handholes 人孔，手孔cover plate for 盖板minimum vessel diameter requiring 所需最小容器直径Manufacture, responsibility of 制造者，职责Manufacturer’s Data Report (see Data Report) 制造厂数据报告(见数据报告)M anufacturer’s stamps 制造厂的印记Marking castings 标志，铸件materials 材料plates 板材standard pressure parts 标志受压件valves and fittings 阀门和配件with Code symbol 带有规范符号Markings, transfer after cutting plates 标志，板材切割以后的转移Materials, approval of new 材料，新材料的批准approval of repairs 修补的批准brazed vessels 钎焊容器carbon and low-alloy steel vessels 碳钢和低合金钢容器cast ductile iron 可锻铸铁castings 铸铁cast iron vessels 铸铁容器certification 合格证clad vessels 覆层容器combination of 组合材料ferritic steel vessels with tensile properties enhanced by heat treatment 经热处理后提高抗拉性能的铁素体钢容器forged vessels 锻造容器for nonpressure parts 非受压元件heat treatment of 热处理high-alloy steel vessels 高合金钢容器inspection of 检查nonferrous vessels 非铁金属容器pipe and tube 管子plate 板rods and bars 杆和棒specification for 标准standard pressure, parts 标准受压元件unidentified 未鉴别的use of over thickness listed in SectionⅡ采用超过列于第Ⅱ卷表中的厚度welded vessels 焊接容器Measurement, 测量dimensional 尺寸of out-of-roundness of shells 壳体不圆度Metal temperature determination 金属温度，确定control of 控制Mill undertolerance 钢厂负公差控制Minimum thickness of plate 板材的最小厚度控制Miscellaneous pressure parts 其它受压件控制Multichamber vessels design 多承压室容器，设计Multiple duplicate vessels 多个相同的容器Multiple safety valves 多个安全阀Nameplates 铭牌New materials 新材料Noncircular vessels 非圆形容器ligament efficiency 孔带系数nomenclature 术语obround design 长圆形设计rectangular design 矩形设计reinforcement 补强examples 实例Nonpressure parts, attachment of 非受压元件的连接Notch ductility test 缺口韧性试验Nozzle openings, reinforced 接管开孔，补强的unreinforced 非补强的vessels subjected to external pressure 承受外压得容器Nozzles attachment of to shell 接管，与壳体的连接minimum thickness of neck 缩颈的最小厚度(see also Connections)(也可见连接件)Nuts and washers 螺母和垫圈Offset of edges of plates at joints 在接头处板边的偏差Openings adjacent to welds 开孔，邻近焊缝closure of 封闭for connections to brazed vessels 用于对钎焊容器的连接for drainage 用于排放head (see Openings head and shell) 封头(见开孔，封头和壳体)in flat heads 在平板封头上inspection 检查manhole (see Manholes) 人孔(见人孔) nozzle (see Nozzle opening) 接管(见接管开孔)shell (see Openings, head and shell) 壳体(见开孔，封头和壳体)through welded joints 通过焊接接头Openings, head and shell, computation of 开孔，封头和壳体，计算not requiring additional reinforcement 不需要附加补强reinforced, size 补强，尺寸reinforcement for adjacent openings 邻近开孔的补强reinforcement of 补强requiring additional reinforcement 需要附加补强shapes permissible 许用形式unreinforced, size 不补强的，尺寸Outlets, discharge, pressure relieving devices 排放口，出料，泄压装置Out-of-roundness 不圆度Overpressure limit for vessels 容器的超压极限Partial data report, manufacturer’s 零部件数据报告，制造厂的Parts, miscellaneous 部件，各种各样的Peening 捶击Pipe connections openings for 管子的连接，用于开孔Pipe fittings vessels built of 管子配件，制造的容器Pipe and tubes 各类管子Pipe used for shells 用作壳体的管子piping external to vessel 容器外的管子Plate, curvature 板，曲率measurement, dimensional check 测量，尺寸校核Plate edges cutting 板边，切割exposed left unwelded 留下不予焊接的显露部分inspection of 检查Plates 平板alignment 找准cover 盖板cutting 切割forming 成型heat treatment 热处理identification 标志impact test 冲击试验inspection 检查laying out 划线less than 6 mm thickness 厚度小6mm markings transfer after cutting 标志，在切割以后的转移minimum thickness 最小厚度repair of defects 缺陷修理specifications 标准structural carbon steel 结构碳钢Plug welds 塞焊Pneumatic test 气压试验pressure 压力yielding 屈服Porosity welded joints 气孔，焊接接头Porosity charts 气孔图Postheat treatment 后热处理connections for nozzles and attachments 用于接管和附件的连接cooling after 随后的冷却furnace temperature 炉温inspection 检查local 局部requirements 要求temperature range 温度范围welded vessels 焊接容器Preheating 预热Preparation of plates for welding 焊接板材的准备pressure, design 压力，设计limits 极限(see also Working pressure, allowable) (也可见工作压力，许用)Pressure parts miscellaneous 受压件，其它的Pressure relieving devices 泄压装置discharge 排放installation and operation 安装和运转rupture disks 防爆模setting 整定Pressure vessels 压力容器exempted from inspection 免检Produce form of Specification 产品技术条件Proof test hydrostatic (see Hydrostatic proof test) 验证试验，水压(见水压试验) Qualification 评定of brazers 钎焊工of welders 焊工of welding procedure 焊接工艺Quality Control System 质量保证体系Quenching and tempering 淬火及回火Quick-actuating closures 快开盖Radiograph factor 射线照相系数Radiographing 射线照相examination by 检查partial 部分quality factors 质量系数requirements 要求spot examination 抽样检查retests 重新试验thickness, mandatory minimum 规定最小厚度Radiographs, acceptance by inspector 射线照相，由检查员认为合格gamma rays, radium capsule γ射线，装镭的盒子interpretation by standard procedure 由标准程序的说明rounded indications 圆形显示Reaming holes for screw stays 为固定螺钉用的铰孔Reducer sections, rules for 变径段，规程Reinforcement 补强defined limits 规定的范围head and shell openings 封头及壳体开孔large openings 大开孔multiple openings 多个开孔nozzle openings 接管开孔of openings in shells, computation of 壳体上开孔，计算openings subject to rapid pressure fluctuation 经受压力突然波动的开孔Fluctuation 经受压力突然波动的开孔strength 强度Relief devices 泄放装置(see also Pressure relieving devices, Safety and relief Valves)(也可见泄压装置，安全阀和泄压阀)Relieving capacity of safety valves 安全阀排量Repairs, approval of defects in material 修理，材料中缺陷的认可defective Brazing 有缺陷的钎焊defects in forgings 锻件中的缺陷defects in welds 焊缝中的缺陷Responsibility of manufacturer 制造者的职责Retention of Records 记录的保存Radiographs 射线照相Manufacturer’s Data Reports 制造厂的数据报告Retests, frogings 复试，锻件impact specimens 冲击试样joints, welded 接头，焊接Rods, bars, and shapes 杆棒喝型材Rolled parts, small 轧制件，小件Rupture disks 爆破模Safety 安全性safety relief, and pressures relief valves, adjustable blow down, capacity certification 安全泄放和泄压阀，可调节的泄放，排放量证明capacity, conversion 排量，换算connection to vessels 连接至容器construction 结构discharge pipe 排放管indirect operation 间接操作installation 安装installation on vessels in service 容器在役时的安装liquid relief 液体泄放marking 标志minimum requirements 最低要求pressure setting 压力整定spring loaded 受载弹簧springs, adjustment 弹簧，调节stop valves adjacent to 邻近的截止阀test 试验protective devices 防护装置for unfired steam boiler 对非直接火蒸气锅炉Scope 适用范围sectioning, closing holes left by 解剖，解剖孔的封闭etching plugs taken 解剖样的侵蚀examination by 检查Service restriction 使用限制Shapes, special 形状，特殊Shell plates, forming ends of 壳体用材料，封头成型Shells 壳体allowable working pressure 许用工作压力computation of openings in 开孔计算forming 成型made from pipe 由管子制造的stiffening rings 刚性环thickness 厚度Transition section 过渡段Sigma-phase formation σ相的形成Skirts length on heads 直边、封头上的长度support of vessels 裙座，容器支撑Slag inclusion welds 焊缝中的夹渣Special constructions 特殊结构Specification for materials 材料标准Spherical sections of vessels 容器的球形部分Spot examination of welded joints 焊接接头的抽样检查Springs for safety valves 安全阀的弹簧Stamping location of 打印位置multipressure vessels 多重压力容器omission of 省略safety valves 安全阀with Code symbol 带有规范标记Stamps, certificate of authorization 钢印，授权low stress 低压力not to be covered 不应覆盖to be visible on plates 在板上可见Static head, in setting safety valves, effect of on limiting stresses 静压头，在整定安全阀时，影响，对极限应力Stayed surfaces 支撑表面Staying formed heads 成型封头的支撑Stays and staybolts, adjacent to edges of staybolted surface 支撑件及拉撑螺栓，邻近用螺栓拉撑得表面周边处allowable stress 许用应力area supported 支撑面dimensions 尺寸ends 端部location 位置pitch 节距screw, holes for 螺孔upset for threading 为车制螺纹的镦粗welded 焊接的Steam generating vessels, unfired 蒸汽锅炉，非直接火Steel, carbon content 钢，含碳量Stenciling plates for identification 在板材上打印标志Stiffening rings, attachment to shell 刚性环，和壳体的装配for vessels under external pressure 用于外压容器Stiffness, support of large vessels for 刚性，大容器支座Stop valves 截止阀adjacent to safety and relief valves 邻近于安全和泄压阀Strength of brazed joints 钎焊接头的强度Stress corrosion cracking 应力腐蚀裂缝Stress values, attachment weld 应力值，连接焊缝basis for establishing 确定的基础carbon and low-alloy steel 碳钢和低合金钢cast iron 铸铁ferritic steels with tensile properties enhanced by heat treatment 经热处理后提高抗拉性能的铁素体刚high-alloy steel高合金钢nonferrous metals 非铁金属Stud bolt threads 双头螺栓螺纹Studded connections 双头螺纹连接Supplementary design formulas 补充设计公式Supports, design 支座，设计pressure vessels 压力容器temperature free movement under 在温度下活动不受约束types of steel permissible for 容许的钢材类型vessels subjected to external pressure 承受外压的容器Surface Weld Metal Buildup 金属堆焊表面Tables, effective gasket width b 表，有效垫片宽度bgasket materials and contact facings 垫片材料和接触面maximum allowable efficiencies for arc and gas welded joints 电弧焊和气焊接头的最大许用系数minimum number of pipe threads for connections 管螺纹连接的最少螺纹牙数molecular weights of gases and vapors 气体和蒸汽的分子量of stress values, carbon and low-alloy steel 应力值，碳钢和低合金钢cast iron 铸铁cast ductile iron 可锻铸铁ferritic steels with tensile properties enhanced by heat treatment经热处理后提高抗拉性能的铁素体钢high-alloy steel 高合金钢nonferrous metals 非铁金属welded carbon low-alloy pipe and tubes 焊接低合金碳钢管of values factor Ｋ系数Ｋ值factor M 系数Ｍfactor 系数postweld heat treatment requirements 焊后热处理要求recommended temperature ranges for heat treatment 推荐的热处理温度范围spherical radius factor K1 球半径系数K1 Telltale holes 指示孔in opening reinforcement 开孔补强Temperature, definitions 温度，定义design 设计determination 确定free movement of vessel on supports 支座上的容器活动不受约束heat treatment 热处理limitations, of brazed vessels 限制，钎焊容器of cast ductile iron 可锻铸铁of postweld heat treating 焊后热处理metal, control of 金属，控制operating or working, definitions 操作或工作，定义zones of different 不同区域Termination point of a vessel 容器的界限点Test coupons 试样Test gages requirements 试验仪表，要求Test plates heat treatment 试板，热处理impact test 冲击试验production 生产Tests, hydrostatic proof 试验，水压验证pneumatic (see pneumatic test) 气压，见气压试验vessels whose strength cannot be calculated 不能由计算求得强度的容器calculated 不能由计算求得强度的容器Thermal buffers 热缓冲器Thermocouples attachment 热电偶，安装Thickness gages, details 厚度量规，细节Thick shells, cylindrical 厚壳体，圆柱形spherical 球形Thin plates marking 薄板，标志Threaded connection 螺纹连接Threaded inspection openings 螺纹检查孔Threads, stud bolts 螺纹，双头螺栓Tolerances, forged shells and heads 公差，锻造容器及封头Toriconical heads 带折边的锥形封头Torispherical heads 带折边的球形封头Transfering marking on plates 板上标志的移植Transition in cylindrical shells 柱状壳体的过渡Trays and baffles, acting as partial shell stiffeners 塔盘及挡板，作为部分壳体加强圈Tubes and pipe 管子Tube-to-tubesheet joints 管子与管板的连接Ultrasonic examination of welds 焊缝的超声检验UM vessels UM 容器Unfired steam boiler 非直接火蒸汽锅炉Unidentified materials 未识别的材料Valves, connections 阀，连接safety and relief (see safety and relief valves) 安全和泄压装置Valves and fittings, marking 阀及其配件，标志Verification tests, heat treatment 验证试验，热处理Volume exemption 容器的免检Weld deposits, cleaning 焊接熔敷金属，清理peening 捶击Welded joints, category 焊接接头，类别description of types 类型的描述efficiency 焊缝系数impact test, across 冲击试验，横向postweld heat treating 焊后热处理radiographic examination, complete 射线照相检查，整个的rounded indications 圆形显示sectioning, etch test 解剖，侵蚀试验spot examination 抽样检查staggered, longitudinal 错开，轴向taper, plates of unequal thicknesses 锥度，不等厚板types around openings 类型，环绕开孔ultrasonic examination of 超声检验Welded reinforcement of nozzle openings 接管开孔的焊缝补强Welded vessels 焊接容器holes in joints of 接头处的孔inspection 检查limitations on 限制tests of 试验Welders and welding operators 焊工和自动焊工identifying stamps 识别标记records of, by manufacturers 由制造厂所作的记录test of qualification 评定试验Welding 焊接cleaning of welded surfaces 焊件表面清理details, limitations 细节，限制forged vessels 锻造容器materials 材料materials having different coefficients of expansion 膨胀系数不同的材料of attachment around openings 开孔周围的连接plate, fitting up joints 平板，连接处的装配plate edges, matching 板边，匹配preparation of plates 钣材的制备procedure qualification 工艺评定processes 工艺test requirement 试验要求Weld metal, composition 焊缝金属，成分Welds acceptability, when radiographed 焊缝合格，用射线照相时when sectioned 解剖时fillet 填角identification of 识别plug 塞焊reinforcement, butt welds 补强，对接焊repairs of defects in 焊缝中缺陷的修补sharp angles, avoid at weld edges 尖角，避免在焊缝边上structural 结构tack 定位焊types, description 类型，描述ultrasonic examination of 超声检验Working pressure allowable, braced and stayed surfaces 许用工作压力，有拉撑和支撑表面by proof test 验证性试验definition of 定英汉锅炉及压力容器词汇AA-number A-No（焊缝金属成分分类号，A=Analysis）A-number analysis A-Number 化学成分A-scan A形扫描ability 能力abnormal situation 异常情况abrupt change in section 截面突变处abrupt transitions 转变的过渡部分absolute coil 绝对线圈absolute manometer 绝对压力计，绝对压强计absolute measurement 绝对测量absolute pressure 绝对压力absolute readout 绝对读数absolute system 绝对系统absolute value 绝对值absorbed energy value 吸收能值absorber 吸收塔absorption 吸附absorption characteristics 吸附特性absorption of hydrogen 吸收氢absorptivity 吸收率abutting pressure parts 相连承压件abutting sections 相连截面accelerated cooling 加速冷却acceptability 可接受性acceptable abbreviation 允许的缩写代号acceptable deviations 允许偏差acceptance criteria 合格指标，验收标准acceptance level 验收标准，合格标准acceptance limit 验收极限acceptance of material 材料的验收acceptance standard 验收标准acceptance test 验收试验access 可达性access door 检查门access for inspector 为检验师提供的方便access for welding 焊接可达性access opening 检查孔，出入孔accessibility of joint 接头可达性access opening 检查孔，出入孔accredit 授权，认可accumulation of time 时间的总和，累加时间accumulation of water 积水accumulation test 蓄汽试验，累积试验accumulation test pressure 蓄汽试验压力accuracy 精度acicular ferrite 针状铁素体acidic slag 酸性渣acidity 酸度acoustic holography 声全息照相acoustic impedance 声阻抗active carbon filter 活性炭过滤器active flux 活性焊剂active gas 活性气体actual design pressure 实际设计压力actual metal temperature 金属实际温度actual stress 真实应力actual stress distribution 实际应力分布actual thickness 实际厚度actual throat （角）焊缝实际厚度actual throat of a fillet weld 角焊缝实际厚度actual value 实际值Adamson furnace 阿登生式炉胆Adamson ring 阿登生圈Adamson type furnace 阿登生式炉胆Adaptor 承接接头adaptive control welding 适应控制焊接added mass 外加质量addenda 增补（在ASME规范中“addenda”一词的内涵甚广，包括“增”“删”“修补”“勘误”等，不仅限于“补遗”）additional bending stress 附加弯曲应力additional data 附加数据additional design principles 补充设计规则additional distortion 附加变形additional fabrication test 附加工艺试验additional inspection 附加检验additional reinforcement 附加补强additional requirements 附加要求additional strain 附加应变additional strength 附加强度additional stress 附加应力additional tension test 附加拉伸试验additional term 附加项additional testing 附加试验additional wall thickness 附加壁厚additional weld metal build-up 额外堆焊的焊缝金属adhering slag 挂渣adhesive content 粘合剂含量adjacent chamber 相邻室，相邻舱adjacent course 相邻筒节adjacent cylinder 相邻筒体adjacent cylindrical section 相邻筒节adjacent hole 邻孔adjacent layer 相邻层adjacent opening 相邻孔adjacent region 临区，相邻区域adjacent sliding surface 邻接的滑动表面，相邻滑动面adjacent surface 相邻面adjoining edge 连接边缘接口adjustable distance piece 可调定距块，可调定距管adjusted pressure ratings for flanges and fittings 法兰和附件的折算压力级别administration fee 管理费用administration supervision 行政监督，管理上的监督adsorbed（surface） moisture （表面）吸附的水分affinity 亲和力affinity for carbon 对碳的亲和力age-hardening crack 时效硬化裂纹ageing 时效ageing induced crack 时效裂纹ageing treatment 时效处理agglomerate flux 粘结焊剂aggregate area 截面积的总和，总截面积aggregate relieving capacity 总泄放量aggregate time 总时间aggregate value capacity 叠加的安全阀排放量air arc cutting 空气电弧切割air-cooled condition 空冷状态air dried hard wood 风干硬木air dried peat 风干泥煤air dried soft wood 风干软木air dried wood 风干木材air entrainment 卷吸空气air pockets 气泡，气袋air-tight coating 气密性覆层air-tight protective coating 气密性保护覆层air-underwater pressure test （管子）水下气压试验algebraic sum 代数和algorithm 算法aligning parts 对准部件alignment tolerance 对准公差alkali ion diode 碱离子二极管alligator crack pattern 鳄鱼皮状裂纹图象（热疲劳裂纹的表现）allowable bolt design stress 螺栓许用设计应力allowable external working pressure 许用工作外压allowable flange stress 法兰许用应力allowable flange stress intensity 法兰许用应力强度allowable maximum service stress 许用最大工作应力allowable staybolt pitch 拉撑螺栓许用节距，拉撑螺栓允许节距allowable stress value 许用应力（值）allowable working pressure 许用工作压力allowance for abrasion 腐蚀裕量allowance for corrosion 腐蚀裕量alloy clad steel plate 合金复合钢板alloy composition 合金成分alloy layer 合金层alloying element 合金元素all-position welding 全位置焊all-weld tensile test 全焊缝金属拉伸试验alternate base material 代用母材alternate heat treatment 另一种热处理（工艺）alternate internal and external pressures 交变内外压alternate plastic strain 交替塑性应变alternate specimen 另一种试样alternate tension test orientation 另一种拉伸试样取样方位alternating stress 交变应力alternating stress amplitude 交变应力幅alternating stress intensity 交变应力强度aluminium (aluminum) 铝aluminium alloy 铝合金aluminium alloy gas cylinder 铝合金气瓶aluminium-base material 铝基材料aluminium-base alloy 铝基合金aluminium bronze 铝青铜aluminium nitride 铝的氮化物aluminium overlay 铝铁合金层American Boiler Manufactures’Association (ABMA) 美国锅炉制造者协会American Society of Metals (ASM) 美国金属学会American Welding Society (AWS) 美国焊接学会ambient temperature 环境温度ammeter shunt 安培计分流器ammonia converter 氨合成塔ammonia liquor scrubber 氨母液洗涤塔ammonium copper acetate solution scrubber 醋酸铜胺洗涤塔amount of corrosion allowance 腐蚀裕量amount of forge work 锻造量amount of machining 机加工量。
