美国H9N称重传感器

称重传感器的接线方法
称重传感器的出线方式有4 线和6 线两种，模块或称重变送器的接线也有
4 线和6 线两种，要接4 线还是6 线首先要看你的硬件要求是怎样的，原则是：传感器能接6 线的不接4 线，必须接4 线的就要进行短接。

一般的称重传感器都是六线制的，当接成四线制时，电源线(EXC-,EXC+)与
反馈线(SEN-,SEN+)就分别短接了。

SEN+和SEN-是补偿线路电阻用的。

SEN+ 和EXC+是通路的，SEN-和EXC-是通路的。

EXC+和EXC-是给称重传感器供电的，但是由于称重模块和传感器之间的线路损耗，实际上传感器接收到的电压会小于供电电压。

每个称重传感器都有一
个mV/V 的特性，它输出的mV 信号与接收到的电压密切相关，SENS+和SENS-实际上是称重传感器内的一个高阻抗回路，可以将称重模块实际接收到的电压反馈给称重模块。

假设EXC+和EXC-为10V,线路损耗，传感器
2mV/V，实际上传感器输出最大信号为()*2=19mV，而不是20mV。

此时称重
传感器内部就会把19mV 作为最大量程，前提是传感器必须通过反馈回路把实际电压反馈给称重模块。

在称重传感器上将EXC+与SENS+短接，EXC-与SENS-短接，仅限于传感器与称重模块距离较近，电压损耗非常小的场合，否则测量存在误差。

tips:感谢大家的阅读，本文由我司收集整编。

仅供参阅！。

C h e c k w e i g h e r sColor touch screenLarge 15” display for excellent visability and easy operation. Dashboard style configuration presents all pertinent information at a glance.9400 shown with an XS controller andoptional signal device.Servo-Cam rejectersThe servo-cam rejecter will gently redirect the non-conformed container without damage or spillage while maintaining maximum throughput./hi-speedFor more informationTechnical data9400– for more uptime and tighter tolerancesStandard features•300 series stainless steel constructions with 2B or #4 finish • 3 weight zones for classification of under, accept, and over weight packages•Gliding Mean Value (selectable from last 5 to 99 weights)•Flexible production line integration •IP65 ingress protectionWeighing controller•Bright, high contrast 15” (VGA) color touch screen display •Embedded Windows XP operating system•Comprehensive display of current product, current packageweight, throughput and mean value gauges, real time individual weight graphic display, zone classification, machine status, standard deviation, message center and help screen•Simple intuitive operation with secondary language capability •Multi-level password security •200 product memory• 3 or 5 weight zones for classification•Gliding Mean Value (selectable from last 5 to 99 weights)•Flexible production line integration •IP65 ingress protectionOptions and accessories•Single head filler feedback control for optimizing fill processes • Statistics program• PrintStick USB device for printing data output• Network interface for METTLER TOLEDO FreeWeigh SQC system •Various monitoring detection devices•Choice of serial interfaces for weight transmission •400 product memory•Range of reject devices, including air blast, sweep, and lift-up rejecters•Up to 7 weight zone classification •Guide rail transfer•Draft shield and reject bins •PortabilityL i n e h e i g h tBase width9400 typical schematicConveyor lengthMettler-Toledo Hi-Speed, Inc.5 Barr Road, Ithaca, NY 14850Toll Free: 800-836-0836Tel: 607-257-6000Fax: 607-257-6396e-mail:***************Subject to technical changes®2007 Mettler-Toledo Hi-Speed, Inc.Printed in U.S.A.6J-01C-0070AThe 9400 is an excellent checkweigher for round containers such as cans, jars, and bottles. The HI-SPEED industry leadership led to the development of the patented 9400 Canweigh design, which integrates timing, spacing and scale sections to eliminate timing screws and enable seam-to-seam weighing.The optional side transfer conveyors can be integrated with reject mechanisms to efficiently quarantine non-conforming products,redirecting them to holding bins, rework lines, or scrap areas.The XS user interface allows for monitoring the Canweigh produc-tion line from long distances.Technical data9400Weighing range, specific to article weight* 28 g to 1200 gPackage diameter Minimum 43 mm, maximum 114 mm Package heightMinimum 26 mm, maximum 184 mm Accuracy* @ ± 2 sigma 1 to 3 gSpeed**50 to 200 fpm Throughput (weighings/minute)** 400 to 800 cpmLine height520 – 1248 mm ±50 mm Typical machine footpring 1248 mm long x 468 mm wideMotor 24 VDC IP 66 servo brushless motors with speed memory Weigh cellHermetically-sealed, moment insenesitive, analog strain gauge Standard sorting/rejecting device Horizontal air-operated mini-plow or vertical servo-cam rejector Compressed air supply 60 to 115 psiPower requirements120/240 VAC, 50/60 Hz, single phase, >500 VA* Depends on the design and dimensions of the weighing belt used** Depends on the weight, dimensions, and transport of the product to be weighedConveyor width。

美国suncells称重传感器suncells传感器HSX-A是美国SUNCELLS公司出品的一款波纹管称重传感器，材质有合金钢和不锈钢可选，采用全激光焊缝，防护等级高，有防尘、防爆等优点。

而且更好的保证了精度，安装也非常的便捷，不易损坏。

美国suncells传感器是美国注册的称重传感器制造商，因其产品价格低廉，质量上乘，是各大化工厂、试验机厂、电子衡器等等行业单位的***。

完善的售后，强大的技术支持，保证suncells产品的广泛应用跟优良的口碑、桥式结构传感器1、QS/QS-A称重传感器，适用于汽车衡、轨道衡、配料秤等。

型号有：QS-5t,QS-10t,QS-15t,QS-20t,QS-25t,QS-30t,QS-40t,QS-50t。

QS-A-5t,QS-A-10t,QS-A-15t,QS-A-20t,QS-A-25t,QS-A-30t,QS-A-40t,QS-A-50 t。

2、QSB-A/-SS称重传感器，适用于汽车衡、轨道衡、轴量秤、地上衡、仓储秤等。

型号有：QSB-A-10klb,QSB-A-20klb,QSB-A-25klb,QSB-A-40klb,QSB-A-50klb,QSB-A-60k lb,QSB-A-75klb。

QSB-SS-10klb,QSB-SS-20klb,QSB-SS-25klb,QSB-SS-40klb,QSB--SS-50klb,QSB -SS-60klb,QSB-SS-75klb。

3、QSC-A/-SS称重传感器，适用于汽车衡、轨道衡、轴量秤、地上衡、仓储秤等。

QSC-A-5klb,QSC-A-10klb,QSC-A-20klb,QSC-A-25klb,QSC-A-30klb,QSC-A-50kl b,QSC-A-60klb,QSC-A-75klb,QSC-A-100klb。

QSC-SS-5klb,QSC-SS-10klb,QSC-SS-20klb,QSC-SS-25klb,QSC-SS-30klb,QSC-S S-50klb,QSC-SS-60klb,QSC-SS-75klb,QSC-SS-100klb。

美国Transcell称重传感器深圳现代豪方-陈工Transcell技术有限公司，于1981年在美国成立，总部在芝加哥北部的布法罗格罗夫，也是Transcell的仓储，分装，运输中。

，专注于称重传感器，邮用称，高精度天平和工业称。

此外还提供国际标准综合设备服务。

1、美国Transcell系列称重传感器：BAB S 型拉压式称重传感器铝制 5M/10M/15M/20M/50M/100MBSA S型拉压式称重传感器合金钢 25kg/50kg/250LBBSS S型拉压式称重传感器合金钢 100kg-750kg/1T/1.5T/2T/5T/7.5T/10TBSS S型拉压式称重传感器:BSS-25kg、BSS-50kg、BSS-100kg、BSS-500kg、BSS-750kg、BSS-1t、BSS-1.5t、BSS-2t、BSS-2.5t、BSS-5t、BSS-7.5t、BSS-10tBAB S型铝制称重传感器BAB-5M BAB-10M BAB-25M BAB-50M BAB-75M BAB-100M BAB-150M BAB-200MBSA S型称重传感器 BSA-25kg\50kg\250lbBSS-ESH S型称重传感器 200kg-5TBSSD S型称重传感器 5T\15T\20TSBS 单悬臂梁式称重传感器 SBS-250kg、SBS-500kg、SBS-1t、SBS-1.5t SBS-2t、SBS-5t、SBS-7.5t、SBS-10t SB 单悬臂梁式称重传感器SBS-ESH 单悬臂梁式称重传感器SBSK 单悬臂梁式称重传感器TA 悬臂梁式称重传感器TSB 单点式称重传感器DBS 双剪梁式称重传感器 DBS-1K lb\1.5K lb\2.5K lb\5K.lb\75K lbDBSQ（QY）桥式称重传感器 QY-10t\20t\25t\30t\50tDBS 双剪梁式称重传感器: DBS-1K lb DBS-1.5K lb DBS-2.5K lb DBS-3K.lb DBS-5K lb DBS-10K lb DBS-15K lb DBS-20K lb DBS-25 K.lb DBS-30K lb DBS-50K lb DBS-75K lbDBSQ（QY）桥式称重传感器数字式称重传感器: QY-10t QY-20t QY-25t QY-30t QY-50tFAD 单点式称重传感器 FAJ 单点式称重传感器 FAS 单点式称重传感器FAV 箱式称重传感器: FAV-60kg FAV-150kg FAV-250kg FAV-500kgFAY 箱式称重传感器: FAY-100kg FAY-150kg FAY-200kg FAY-250kg FAY-300kg FAY-500kg FAY-635kg FAY-1000kgFGA 箱式称重传感器:FGA-3kg FGA -5kg FGA -10kg FGA -15kg FGA -20kg FGA -30kg FGA-50kgK700 K800箱式称重传感器MSB 轮辐式称重传感器DBST 柱式称重传感器DBSL 轮辐式称重传感器DBSL-5T/DBSL-10T/DBSL-20T/DBSL-30TTSB 单点式称重传感器/DBS 双剪梁式称重传感器 DBS-1K lb\1.5K lb\2.5K lb\5K.lb\75K lbDBSQ（QY）桥式称重传感器 QY-10t\20t\25t\30t\50t/FAD 单点式称重传感器TC-2005 计数秤/TC-2010 计数秤/TP-500 称量计数系统/MS-1000 工业秤/MSB-500BW 工业秤MSB-500E 工业秤/PC系列工业秤/SPC系列工业秤/SP系列工业秤/SRP-300 工业秤/SSB-3500 工业秤MSB-4300 多用途工业秤/WEIGHBLOK系列工业秤/SSP-3400 平台秤/MSP-4200 平台秤CR-500 吊钩秤/Guardian系列地磅/PALLET RUNNER 叉车秤/Weigh Beam便携式称重系统/数字式称重传感器FAV 箱式称重传感器 FAV-60kg\150kg\250kg\500kgFAY 箱式称重传感器 FAY—100kg\150kg\200kg\500kg\1000kgMSB 轮辐式称重传感器/DBST 柱式称重传感器/NEPTUNE-4500 检重秤/NEPTUNE-4500显示仪表NEPTUNE-5500 检重秤/NEPTUNE-5500 显示仪表/NEPTUNE-6500检重秤/NEPTUNE-6500显示仪表T1-500BW 数字显示仪表/T1-500E 称重显示仪表/T1-500E-SS 耐用称重显示仪表/T1-500SL 耐用显示仪表T1-600ESS化工称重显示仪表/T1-1500 高精度显示仪表/T1-1600 高精度显示仪表/大屏幕显示器数字汽车衡称重管理软件操作手册/RF 无线数据传送模块使用说明/MP-20 热敏打印机2、长期供应美国Transducer Techniques称重传感器及仪表（1）Transducer Techniques称重传感器力传感器：HFG：11LB 45LB 110LB;GSO: 10,25,30,50,100,150,250,500,1K GRAMS;MDB: 2.5, 5, 10, 25, 50, 75, 100 LBS;MLP: 10,25,50,75,100,150,200,300,500,750,1K LBS;SLB: 25, 50, 100, 250,500, 750, 1K LBS.LBO: 100,250,500,750,1K,2K,3K,5K,10K,15K,20K,30K,50K LBS.LBC: 100,250,500,750,1K,2K,3K,5K,10K,15K,20K,30K,50K LBS;LBM: 50,100,200,500,1k,2K,2.5K,5K,8K,10K LB;MLC: 2K, 3K, 5K, 7.5K, 10K, 15K,20K,30K lb;CLC: 50K, 100K, 200K, 300K, 400K lb(柱式）；THA：50, 100, 250, 500 LBS.THB：100, 250, 500, 1,000, 2,000 LBS.；THC：3,000, 5,000, 7,500, 10,000 LBS；THD：2K, 3K, 5K, 7.5K, 10K,15K, 20K, 30K, 50K LBS;LWO: 2.4K, 4K, 7K, 10K, 14K, 20K, 25K, 30K, 45K, 60K, 80K,125K, 190K, 260K, 300K lb;SSM: 50,100,200,500,1K, 2K, 2.5K,5K, 8K, 10K LBS;DSM: 50,100,200,500,1K, 2K, 2.5K,5K, 8K, 10K LBS;TLL: 500, 1K, 2K, 3K, 5K, 10K, 20K, 30K, 50K lb;SBO: 50, 100, 200, 300, 500, 750,1K, 2K, 3K, 5K LBS;SWO: 1K, 2K, 3K, 5K,10K, 20K, 30K, 50K LBS;HSW: 1K, 2K, 3K, 5K,10K, 20K, 30K, 50K LBS;LPO: 500, 1k, 2k, 3k, 5k, 10k, 20k LBS;LPU: 100,250,500,1K,2K,3K,4K,5K,7.5K,10K,15K,20K,30K, 50K LBS;SWP: 1K, 2K, 3K,5K, 10K, 20K, 50K LBS ;CLP: 750, 1.5K, 3K, 6K,12.5K, 18K, 30K lb ;(2) Transducer Techniques称重传感器梁式传感器：TBS：0.25, 0.50, 1, 2, 5,10, 20, 40 LBS；EBB：1, 2, 5,10 Kg.LSP：1, 2, 5,10 Kg；ESP：6, 10, 15, 20, 25, 30, 35 Kg.SPL：65, 100, 150, 200, 300, 500 Kg.；SBL：500, 1K, 2K, 2.5K, 3K,4K, 5K, 10K, 15K,20K LBS.(3) Transducer Techniques称重传感器扭矩传感器：RST：10，20，50，100，200，500，1K，2K，5K，12K，30K inch lbs;RSS：10, 20, 50, 100, 250, 600, 1K FT-LBS ；RTS：5, 10, 25, 50, 100, 200, 500, 1K Oz-inch;TRT: 25, 50, 100, 200, 500 INCH-LBS;TRS: 500, 1K, 2K, 5K, 10K, 20K, 50K, 100K INCH LBS;SWS: 10, 20, 50, 100, 250, 600, 1K FT-LBS ;STS: 600, 1.2K, 2K, 3K, 6K, 12K inch lbs ;显示仪表系列：DPM-2 DPM-3 TIO-3000 PHM-100；接线盒、放大器：TMO-2、TMO-2A、PSM-F10、PSMR、DSP-1、TM0-1、TMO-1-24VDC、SJB-4、TSM-3MV3、供应美国Transducer Techniques称重传感器及仪表（1）力传感器：HFG：11LB 45LB 110LB;GSO: 10,25,30,50,100,150,250,500,1K GRAMS;MDB: 2.5, 5, 10, 25, 50, 75, 100 LBS;MLP: 10,25,50,75,100,150,200,300,500,750,1K LBS;SLB: 25, 50, 100, 250,500, 750, 1K LBS.LBO: 100,250,500,750,1K,2K,3K,5K,10K,15K,20K,30K,50K LBS.LBC: 100,250,500,750,1K,2K,3K,5K,10K,15K,20K,30K,50K LBS;LBM: 50,100,200,500,1k,2K,2.5K,5K,8K,10K LB;MLC: 2K, 3K, 5K, 7.5K, 10K, 15K,20K,30K lb;CLC: 50K, 100K, 200K, 300K, 400K lb(柱式）；THA：50, 100, 250, 500 LBS.THB：100, 250, 500, 1,000, 2,000 LBS.；THC：3,000, 5,000, 7,500, 10,000 LBS；THD：2K, 3K, 5K, 7.5K, 10K,15K, 20K, 30K, 50K LBS;LWO: 2.4K, 4K, 7K, 10K, 14K, 20K, 25K, 30K, 45K, 60K, 80K,125K, 190K, 260K, 300K lb;SSM: 50,100,200,500,1K, 2K, 2.5K,5K, 8K, 10K LBS;DSM: 50,100,200,500,1K, 2K, 2.5K,5K, 8K, 10K LBS;TLL: 500, 1K, 2K, 3K, 5K, 10K, 20K, 30K, 50K lb;SBO: 50, 100, 200, 300, 500, 750,1K, 2K, 3K, 5K LBS;SWO: 1K, 2K, 3K, 5K,10K, 20K, 30K, 50K LBS;HSW: 1K, 2K, 3K, 5K,10K, 20K, 30K, 50K LBS;LPO: 500, 1k, 2k, 3k, 5k, 10k, 20k LBS;LPU: 100,250,500,1K,2K,3K,4K,5K,7.5K,10K,15K,20K,30K, 50K LBS;SWP: 1K, 2K, 3K,5K, 10K, 20K, 50K LBS ;CLP: 750, 1.5K, 3K, 6K,12.5K, 18K, 30K lb ;(2)梁式传感器：TBS：0.25, 0.50, 1, 2, 5,10, 20, 40 LBS；EBB：1, 2, 5,10 Kg.LSP：1, 2, 5,10 Kg；ESP：6, 10, 15, 20, 25, 30, 35 Kg.SPL：65, 100, 150, 200, 300, 500 Kg.；SBL：500, 1K, 2K, 2.5K, 3K,4K, 5K, 10K, 15K,20K LBS.(3)扭矩传感器：RST：10，20，50，100，200，500，1K，2K，5K，12K，30K inch lbs;RSS：10, 20, 50, 100, 250, 600, 1K FT-LBS ；RTS：5, 10, 25, 50, 100, 200, 500, 1K Oz-inch;TRT: 25, 50, 100, 200, 500 INCH-LBS;TRS: 500, 1K, 2K, 5K, 10K, 20K, 50K, 100K INCH LBS;SWS: 10, 20, 50, 100, 250, 600, 1K FT-LBS ;STS: 600, 1.2K, 2K, 3K, 6K, 12K inch lbs ;显示仪表系列：DPM-2 DPM-3 TIO-3000 PHM-100；接线盒、放大器：TMO-2、TMO-2A、PSM-F10、PSMR、DSP-1、TM0-1、TMO-1-24VDC、SJB-4、TSM-3MV4、供应Vishay nobel称重传感器压力传感器KIS-1、KIS-2、KIS-3、KIS-8、KIS-9、KIS-11、KIM-1、 KISD-6、KOM-1、 KOSD-40、 KOSD、 KIP-1威世诺贝尔Vishay Nobel的产品范围包括用于制药、化学、食品和其它需成批处理产业的高质量的测压元件、仪器和软件。

OS100 SERIES Mini-Infrared Transmitter e-mail:**************For latest product manuals: Shop online at User’s G ui d e***********************Servicing North America:U.S.A. Omega Engineering, Inc.Headquarters: Toll-Free: 1-800-826-6342 (USA & Canada only)Customer Service: 1-800-622-2378 (USA & Canada only)Engineering Service: 1-800-872-9436 (USA & Canada only)Tel: (203) 359-1660 Fax: (203) 359-7700e-mail:**************For Other Locations Visit /worldwideThe information contained in this document is believed to be correct, but OMEGA accepts no liability for any errors it contains, and reserves the right to alter specifications without notice.Table of ContentsSection ...................................................................PageSafety Warnings and IEC Symbols (iii)Caution and Safety Information (iii)Section 1 Introduction ....................................................................1-1Section 2Installation ......................................................................1-12.1 Unpacking and Inspection ......................................1-12.2 Electrical Connection ..............................................2-1Section 3Operation ........................................................................3-13.1 Main Board ................................................................3-13.2 Ambient Temperature ..............................................3-23.3 Atmospheric Quality ................................................3-33.4 Measuring Temperature ..........................................3-33.5 Alarm Setting ............................................................3-43.6 Adding Extension Cable...........................................3-4Section 4 Laser Sight Accessory ...................................................4-14.1 Warning and Cautions .............................................4-14.2 Operating the Laser Sight Accessory .....................4-1Section 5 Specifications .................................................................5-15.1 General .......................................................................5-15.2 Laser Sight Accessory (OS100-LS) ..........................5-2Section 6Emissivity Table .............................................................6-1iTable of FiguresFigure Description Page2-1Power Supply & Analog Output Connections ..........2-12-2 Alarm Output Connection ............................................2-13-1 Main PC Board ...............................................................3-23-2 Sensor..............................................................3-2Housing3-3 Optical Field of View .....................................................3-43-4Setting the Temperature Engineering Unit..................3-43-5Mounting Bracket OS100-MB .......................................3-53-6Water Cooling Jacket, OS100-WC ................................3-53-7Typical Water Cool Jacket Assembly ...........................3-53-8Air Purge Collar, OS100-AP..........................................3-63-9DIN Rail Mounting Adapter, OS100-DR ....................3-63-10NEMA-4 Aluminum Enclosure ....................................3-64-1Laser Sighting Accessory, OS100-LS ............................4-24-2Laser Warning Label ......................................................4-2iiSafety Warnings and IEC SymbolsThis device is marked with international safety and hazard symbols in accordance with IEC 1010. It is important to read and follow all precautions and instructions in this manual before operating or commissioning this device as it contains important information relating to safety and EMC. Failure to follow all safety precautions may result in injury and or damage to your calibrator. IEC symbols DescriptionCaution and Safety Information• If the equipment is used in a manner not specified in this manual, the protection provided by the equipment may be impaired.• The installation category is one (1).• There are no user replaceable fuses in this product• The output terminals of this product are for use with equipment (digital meters, chart recorders, etc,) which have no accessible five parts. Such equipment should comply with all the applicable safety requirements.• Do not operate the equipment in flammable or explosive environments.• All connections to the thermometer should be made via a shielded cable, 24 AWG stranded wire with the following ratings: 300V , 105°C (221°F), PVC insulation.• Power must be disconnected before making any electrical connections.• The power supply used to power the thermometer should be VDE or UL approved with the following ratings: 12 to 24vdc @150mA with overload protection of 500mA.iiiCaution, refer to accompanying documentsDirect Current Laser SymbolFrame or ChassisNOTES: ivSection 1 - IntroductionThe low cost OS101 mini-infrared transmitter provides non-contacttemperature measurement for industrial applications. The unit measures atemperature range of -18 to 538°C (0-1000°F) and provides a linear analogoutput of either 4-20 mA, 0-5 VDC, K type TC, 1 mV/°C, or 1 mV/°F.The new OS102 mini-infrared transmitter has all the functions of OS101plus a built-in LED display that shows the measured temperature indegrees F or degrees C which is switchable in the field.The miniature sensor head design 2.5 cm dia. x 6.3 cm Length (1" x 2.5") isideal for measuring temperature in confined, and hard to reach places.The aluminum sensor head as well as the rugged electronic housing (Diecast Aluminum) are NEMA-4 rated.The sensor head is connected to the electronic housing via a 1.82 m (6 feet)shielded cable as standard. The unit provides field adjustable alarmoutput.Section 2 - Installation2.1UnpackingRemove the packing list and verify that you have received all yourequipment. If you have any questions about the shipment, please callCustomer Service at:1-800-622-2378 or 203-359-1660. We can also be reached on the internet:e-mail:**************When you receive the shipment, inspect the container and equipment forany signs of damage. Note any evidence of rough handling in transit.inspection. After examination and removing contents, save packing material and carton in theevent reshipment is necessary.The following items are supplied in the box:• The infrared transmitter including the sensor head and the 1.82 m(6 feet) shielded cable• User's Manual• Mounting Nut1-1The following describes the ordering information:OS102 or OS101 - MA- *,**, where The following optional accessories are available:Here are the Features of OS101 and OS102 infrared transmitters:2.2Electrical Connection Sensor Head Cable - The Sensor head is pre-wired to a 1.8 m (6 feet)shielded cable. Plug & lock-in the male connector to the mating female connector on the aluminum housing.Power & Output Connection - Open the cover of the main aluminum housing. Slide the cable through the strain relief and connect the wires to the terminal block on the board as shown in Fig. 2-1. For Alarm output connection, refer to Fig. 2-2.2-1MA - 4/20 mA output V1 - 0 to 5 VDC output K - Thermocouple output, K type MV - Millivolt output C - 1 mV/°C output F - 1 mV/°F output HT- High temperature sensor head3-1Figure 2-2. Alarm Output Connection Section 3 - Operation3-1Main BoardThe Main Board is shown in Fig. 3-1. Here are the important components on the board:(1) - Terminal Block for Power & Output connections(2) - Single Turn Potentiometer to adjust Emissivity in tenths (0.x_)(3) - Single Turn Potentiometer to adjust Emissivity in hundreds (0._x)(4) -Slide switch to select between real time (Normal Operation) and alarm set point(5) - Alarm set point adjust, P4(6) - Sensor Head connection(7) - Input Zero adjust, P3(8) - Input Span adjust, P2(9) - Output Zero adjust, P5(10) - Output Span adjust, P6Figure 3-1. Main PC Board3.2Ambient TemperatureThe Sensing head can operate in an ambient temperature of 0 to 70°C (32to 158°F). The Sensing head in the high temperature model (-HT) can operate in an ambient temperature of 0 to 85°C (32 to 185°F) without any cooling required. The Sensing head can operate up to 200°C (392°F) using the water cool jacket accessory OS100-WC (See Fig. 3-6).There is a warm up period of 3 minutes after power up. After the warm up period, temperature measurement can be made.When the ambient temperature around the sensor head changes abruptly,the sensor head goes through thermal shock. It takes a certain amount of time for the sensor head to stabilize to the new ambient temperature. For example, it takes about 30 minutes for the sensor head to stabilize going from 25°C to 50°C (77 to 122°F) ambient temperature.The sensor head dimensions are shown in Fig. 3-2.Figure 3-2. Sensor Housing3-23-33.3Atmospheric QualityEnvironments with smoke, dust, and fumes dirty up the optical lens, and cause erroneous temperature readings. To keep the surface of the optical lens clean, the air purge collar accessory is recommended, OS100-AP , See Fig. 3-7.3.4Measuring TemperatureBefore starting to measure temperature, make sure that the following check list is met:ߜ The power and analog output connections are made (Fig. 2-1).ߜThe sensor head is connected to the main unit.ߜThe slide switch (SW1) on the main board is set to real time (Fig. 3-1).ߜThe target is larger than the optical field of view of the sensor head (Fig. 3-3).ߜThe emissivity adjustment on the main board is set properly (Fig. 3-1).ߜThe output load is within the product specification.On OS102 transmitters, follow these additional steps:ߜ The temperature display is set to °F or °C (Fig. 3-4)ߜ For 4-20mA output models, make sure an output load is added, ie. 250ohms.Figure 3-3. Optical Field Of ViewFigure 3-4. Setting the Temperature Engineering Unit3.5Alarm SettingThe unit provides 0-100% alarm set point adjustment. Here is an exampleof an alarm setting.• An OS101-MA(4/20 mA output), the alarm is to be set at 400°Ftemperature.• Connect the alarm output as shown in Fig. 2-2.• Set the slide switch (SW1) on the main board to the Alarm position.• Measure the analog output, and set the Potentiometer P4 until theoutput reads 10.4 mA which is 40% (400°F) of the temperature range.40 x (20-4)[10.4mA=+ 4]100• Set the slide switch (SW1) back to the Real Time position.• If the temperature reading is below the alarm set point, the alarmoutput stays high, otherwise it goes low.On the OS102, you can set the alarm set point directly based on thetemperature display.3.6Adding Extension CableYou can add extension cable between the Sensor Head and the mainelectronic housing up to 15.2 m (50 feet). After adding the extension cable,the Zero input potentiometer, P3 may be re-adjusted. (See Fig. 3-1, forproper analog output reading)The following figures show the mounting bracket (OS100-MB), Watercooling jacket (OS100-WC), Air purge collar (OS100-AP), DIN RailMounting adapter (OS-100-DR), and the main aluminum enclosure. TheDIN Rail Mounting adapter (OS100-DR) is mounted to the bottom of themain aluminum enclosure using two 4-40 screws.A typical water cool jacket assembly is shown in Fig. 3-7, on the following page.1. Mounting Nut2. Mounting Bracket3. Water Cool Jacket4. Sensor Head3-4Figure 3-5. Mounting Bracket OS100-MBFigure 3-6. Water Cooling Jacket, OS100-WCFigure 3-7. Typical Water Cool Jacket Assembly3-5Figure 3-8. Air Purge Collar, OS100-APFigure 3-9. DIN Rail Mounting Adapter, OS-100-DRFigure 3-10. NEMA-4 Aluminum Enclosure3-6Section 4 - Laser Sight Accessory4.1Warning and Cautionsbelow:•Use of controls or adjustments or performance of procedures other than those specified here may result in hazardous radiation exposure.• Do not look at the laser beam coming out of the lens or view directly with optical instruments - eye damage can result.• Use extreme caution when operation the laser sight accessory • Never point the laser accessory at a person • Keep out of the reach of all children4.2Operating the Laser Sight AccessoryThe laser sight accessory screws onto the front of the sensor head. This accessory is only used for alignment of the sensor head to the target area.After the alignment process, the accessory has to be removed from the front of the sensor head before temperature measurement.The laser sight accessory is powered from a small compact battery pack (included with the accessory). Connect the battery pack to the accessory using the cable provided. Aim at the target, and turn on the battery power using the slide switch on the battery pack. Adjust the sensor head position so that the laser beam points to the center of the target area. Turn off the battery pack, and remove the laser sighting accessory from the sensor head. See Fig. 4-1 for reference.4-14-2Figure 4-2. Laser Warning LabelSection 5 - Specifications5.1 - GeneralTemperature Range-18 to 538°C (0 to 1000°F)Accuracy @ 22°C (72°F)±2% of Rdg. or 2.2°C (4°F) whichever is ambient temperature & greateremissivity of 0.95 or greaterOptical Field of View6:1 (Distance/Spot Size)Repeatability±1% of Rdg.Spectral Response 5 to 14 micronsResponse Time150 msec (0 to 63% of final value)Emissivity Range0.1 to 0.99, adjustableOperating Ambient TemperatureMain Transmitter0 to 50°C (32 to 122°F)Sensor Head0 to 70°C (32 to 158°F)Sensor Head (-HT Model)0 to 85°C (32 to 185°F)Sensor Head with OS100-WC(Water Cooling Jacket)0 to 200°C (32 to 392°F)Operating Relative Humidity Less than 95% RH, non-condensingWater Flow Rate for OS100-WC0.25 GPM, room temperatureThermal Shock About 30 minutes for 25°Cabrupt ambient temperature change Warm Up Period 3 minutesAir Flow Rate for OS100-AP 1 CFM (0.5 Liters/sec.)Power12 to 24 VDC @ 100 mAAnalog OutputsMV-F 1 mV/°FMV-C 1 mV/°CK K Type TC - OS101 onlyMA 4 to 20 mAV10 to 5 VDCOutput Load requirementsMin. Load (0 to 5VDC) 1 K-OhmsMax. Load (4 to 20 mA)(Supply Power - 4 )/20 mATransmitter Housing NEMA-4 & IP65, Die Cast AluminumSensor Head Housing NEMA-4 , AluminumAlarm Output Open Drain, 100 mAAlarm Set Point0 to 100% , Adjustable via P4Alarm Deadband14°C (25°F)5-15-25.1 - General Con’t.DimensionsSensor Head25.4 OD. x 63.5 mm L(1" OD. x 2.5" L)Main Housing, OS10165.5 W x 30.5 H x 115.3 mm L(2.58" W x 1.2" H x 4.54" L)Main Housing, OS10265.5 W x 55.9 H x 115.3 mm L(2.58" W x 2.2" H x 4.54" L)Weight 272 g (0.6 lb)5.2Laser Sight Accessory (OS100-LS)Wavelength (Color)630 - 670 nm (Red)Operating Distance (Laser Dot)Up to 9.1 m (30 ft.)Max. Output Optical Power Less than 1 mW at 22°F ambienttemperature.European Classification Class 2, EN60825-1/11.2001Maximum Operating current45 mA at 3 VDCFDA Classification Complies with 21 CFR 1040.10,Class II Laser ProductBeam Diameter 5 mmBeam Divergence< 2 mradOperating Temperature0 to 50°C (32 to 122°F)Operating Relative Humidity Less than 95% RH, non-condensingPower Switch ON / OFF , Slide switch on the BatteryPackPower Indicator Red LEDPower Battery Pack, 3 VDC (Consists of two 1.5VDC AA size Lithium Batteries) Laser Warning Label Located on the head sight circumferenceIdentification Label Located on the head sight circumferenceDimensions38 DIA x 50.8 mm L(1.5" DIA x 2" L)Section 6 - Emissivity Table6-1Material Emissivity (ε)Aluminum – pure highly polished plate . . . . . . . . . . . . . . . . . . . . . . . . 0.04 to 0.06Aluminum – heavily oxidized . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.20 to 0.31Aluminum – commercial sheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.09Brass – dull plate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.22Brass – highly polished, 73.2% Cu, 26.7% Zn. . . . . . . . . . . . . . . . . . . . . . . . . 0.03Chromium – polished. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.08 to 0.36Copper – polished. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.05Copper – heated at 600°C (1112°F). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.57Gold – pure, highly polished or liquid. . . . . . . . . . . . . . . . . . . . . . . . . 0.02 to 0.04Iron and steel (excluding stainless)– polished iron . . . . . . . . . . . . . . . . 0.14 to 0.38Iron and steel (excluding stainless)– polished cast iron. . . . . . . . . . . . . . . . . . . 0.21Iron and steel (excluding stainless)– polished wrought iron . . . . . . . . . . . . . . . 0.28Iron and steel (excluding stainless)– oxidized dull wrought iron . . . . . . . . . . . . 0.94Iron and steel (excluding stainless)– rusted iron plate . . . . . . . . . . . . . . . . . . . 0.69Iron and steel (excluding stainless)– polished steel. . . . . . . . . . . . . . . . . . . . . . 0.07Iron and steel (excluding stainless)– polished steel oxidized at600°C (1112°F). . . . . . . . . . . . . . . . . . . . 0.79Iron and steel (excluding stainless)– rolled sheet steel . . . . . . . . . . . . . . . . . . . 0.66Iron and steel (excluding stainless)– rough steel plate . . . . . . . . . . . . . 0.94 to 0.97Lead – gray and oxidized . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.28Mercury . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.09 to 0.12Molybdenum filament . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.10 to 0.20Nickel – polished . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.07Nickel – oxidized at 649 to 1254°C (1200°F to 2290°F). . . . . . . . . . . 0.59 to 0.86Platinum – pure polished plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.05 to 0.10Platinum – wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.07 to 0.18Silver – pure and polished . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.02 to 0.03Stainless steel – polished . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.07Stainless steel – Type 301 at 232 to 942°C (450°F to 1725°F). . . . . . . 0.54 to 0.63Tin – bright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.06Tungsten – filament . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.39Zinc – polished commercial pure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.05Zinc – galvanized sheet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.23M E T A L S6-2Material Emissivity (ε) Asbestos Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.96 Asphalt, tar, pitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.95 to 1.00 Brick– red and rough . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.93 Brick– fireclay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.75 Carbon– filament . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.53 Carbon– lampblack - rough deposit . . . . . . . . . . . . . . . . . . . . . . . . . .0.78 to 0.84 Glass- Pyrex, lead, soda . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.85 to 0.95 Marble– polished light gray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.93 Paints, lacquers, and varnishes– Black matte shellac . . . . . . . . . . . . . . . . . . . .0.91 Paints, lacquers, and varnishes– aluminum paints . . . . . . . . . . . . . . . .0.27 to 0.67 Paints, lacquers, and varnishes– flat black lacquer . . . . . . . . . . . . . . .0.96 to 0.98 Paints, lacquers, and varnishes– white enamel varnish . . . . . . . . . . . . . . . . . .0.91 Porcelain– glazed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.92 Quartz– opaque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.68 to 0.92 Roofing Paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.91 Tape– Masking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.95 Water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.95 to 0.96 Wood– planed oak . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.90 NONMETALSNOTES:6-3NOTES: 6-4OMEGA’s policy is to make running changes, not model changes, whenever an improvement is possible. T his affords our customers the latest in technology and engineering.OMEGA is a trademark of OMEGA ENGINEERING, INC.© Copyright 2017 OMEGA ENGINEERING, INC. All rights reserved. T his document may not be copied, photocopied, reproduced, translated, or reduced to any electronic medium or machine-readable form, in whole or in part, without the prior written consent of OMEGA ENGINEERING, INC.FOR WARRANTY RETURNS, please have the following information available BEFORE contacting OMEGA:1. P urchase Order number under which the product was PURCHASED,2. M odel and serial number of the product under warranty, and3. Repair instructions and/or specific problems relative to the product.FOR NON-WARRANTY REPAIRS, consult OMEGA for current repair charges. Have the following information available BEFORE contacting OMEGA:1. Purchase Order number to cover the COST of the repair,2. Model and serial number of the product, and 3. Repair instructions and/or specific problems relative to the product.RETURN REQUESTS/INQUIRIESDirect all warranty and repair requests/inquiries to the OMEGA Customer Service Department. BEFORE RET URNING ANY PRODUCT (S) T O OMEGA, PURCHASER MUST OBT AIN AN AUT HORIZED RET URN (AR) NUMBER FROM OMEGA’S CUST OMER SERVICE DEPART MENT (IN ORDER T O AVOID PROCESSING DELAYS). The assigned AR number should then be marked on the outside of the return package and on any correspondence.T he purchaser is responsible for shipping charges, freight, insurance and proper packaging to preventbreakage in transit.WARRANTY/DISCLAIMEROMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a period of 25 months from date of purchase. OMEGA’s WARRANTY adds an additional one (1) month grace period to the normal two (2) year product warranty to cover handling and shipping time. This ensures that OMEGA’s customers receive maximum coverage on each product.If the unit malfunctions, it must be returned to the factory for evaluation. OMEGA’s Customer Service Department will issue an Authorized Return (AR) number immediately upon phone or written request. Upon examination by OMEGA, if the unit is found to be defective, it will be repaired or replaced at no charge. OMEGA’s WARRANT Y does not apply to defects resulting from any action of the purchaser, including but not limited to mishandling, improper interfacing, operation outside of design limits, improper repair, or unauthorized modification. T his WARRANT Y is VOID if the unit shows evidence of having been tampered with or shows evidence of having been damaged as a result of excessive corrosion; or current, heat, moisture or vibration; improper specification; misapplication; misuse or other operating conditions outside of OMEGA’s control. Components in which wear is not warranted, include but are not limited to contact points, fuses, and triacs.OMEGA is pleased to offer suggestions on the use of its various products. However, OMEGA neither assumes responsibility for any omissions or errors nor assumes liability for any damages that result from the use of its products in accordance with information provided by OMEGA, either verbal or written. OMEGA warrants only that the parts manufactured by the company will be as specified and free of defects. OMEGA MAKES NO OTHER WARRANTIES OR REPRESENTATIONS OF ANY KIND WHATSOEVER, EXPRESSED OR IMPLIED, EXCEPT THAT OF TITLE, AND ALL IMPLIED W ARRANTIES INCLUDING ANY W ARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. LIMITATION OF LIABILITY: The remedies of purchaser set forth herein are exclusive, and the total liability of OMEGA with respect to this order, whether based on contract, warranty, negligence, indemnification, strict liability or otherwise, shall not exceed the purchase price of the component upon which liability is based. In no event shall OMEGA be liable for consequential, incidental or special damages.CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor shall it be used: (1) as a “Basic Component” under 10 CFR 21 (NRC), used in or with any nuclear installation or activity; or (2) in medical applications or used on humans. Should any Product(s) be used in or with any nuclear installation or activity, medical application, used on humans, or misused in any way, OMEGA assumes no responsibility as set forth in our basic WARRANT Y /DISCLAIMER language, and, additionally, purchaser will indemnify OMEGA and hold OMEGA harmless from any liability or damage whatsoever arising out of the use of theProduct(s) in such a manner.Where Do I Find Everything I Need forProcess Measurement and Control?OMEGA…Of Course!Shop online at TEMPERATUREM U Thermocouple, RTD & Thermistor Probes, Connectors,Panels & AssembliesM U Wire: Thermocouple, RTD & ThermistorM U Calibrators & Ice Point ReferencesM U Recorders, Controllers & Process MonitorsM U Infrared PyrometersPRESSURE, STRAIN AND FORCEM U Transducers & Strain GagesM U Load Cells & Pressure GagesM U Displacement TransducersM U Instrumentation & AccessoriesFLOW/LEVELM U Rotameters, Gas Mass Flowmeters & Flow ComputersM U Air Velocity IndicatorsM U Turbine/Paddlewheel SystemsM U Totalizers & Batch ControllerspH/CONDUCTIVITYM U pH Electrodes, Testers & AccessoriesM U Benchtop/Laboratory MetersM U Controllers, Calibrators, Simulators & PumpsM U Industrial pH & Conductivity EquipmentDATA ACQUISITIONM U Communications-Based Acquisition SystemsM U Data Logging SystemsM U Wireless Sensors, Transmitters, & ReceiversM U Signal ConditionersM U Data Acquisition SoftwareHEATERSM U Heating CableM U Cartridge & Strip HeatersM U Immersion & Band HeatersM U Flexible HeatersM U Laboratory HeatersENVIRONMENTALMONITORING AND CONTROLM U Metering & Control InstrumentationM U RefractometersM U Pumps & TubingM U Air, Soil & Water MonitorsM U Industrial Water & Wastewater TreatmentM U pH, Conductivity & Dissolved Oxygen InstrumentsM3572/1217。

美国Zemic称重传感器广州南创电子科技有限公司传感器事业部内部使用资料美国ZEMIC有限公司在美国成立,在多个国家设立了分支机构或办事处,生产基地遍布美洲、东欧等地,在中国设立了广州南创传感器事业部,可为用户的实验和生产提供最佳的服务与解决方案。

美国Zemic称重传感器美国Zemic称重传感器单点式称重传感器：美国ZEMIc称重传感器，如下：Zemic称重传感器HM14C-C3-30T-13B6特性◆可满足0.05kg-300kg量程范围内的测量。

◆铝合金材料，平行梁结构◆硅橡胶密封，表面阳极化，耐腐蚀性佳。

◆整体结构，安装使用方便。

◆适用于电子计价秤、电子平台秤等各类电子称重设备。

◆量程：0.05㎏到300㎏◆高精度◆最大秤台尺寸450*450㎜Zemic称重传感器（load cell）单点式称重传感器L6B、L6D、L6E、L6E3、L6F、L6G、L6J、L6H5：L6E3-C3-50kg-3G,L6E3-C3-100kg-3G,L6E3-C3-150KG-3G,L6E3-C3-200KG-3G,L6E3-C3-25 0KG-3G,L6E3-C3-300KG-3G,L6E-C3-50KG-2B,L6E-C3-60KG-2B,L6E-C3-80KG-2B,L6E-C3-100KG-2B,L6E-C3-150KG-2B, L6E-C3-200KG-2B,L6E-C3-300KG-2B,L6D-C3-2.5KG-0.4B,L6D-C3-3KG-0.4B,L6D-C3-5KG-0.4B,L6D-C3-6KG-0.4B ,L6D-C3-8KG-0.4B,L6D-C3-10KG-0.4B,L6D-C3-15KG-0.4B,L6D-C3-20KG-0.4B,L6D-C3-30KG-0.4B,L6D-C 3-35KG-0.4B,L6D-C3-40KG-0.4B,L6D-C3-50KG-0.4BL6H5-C3D-4KG-1.75B，L6H5-C3D-5KG-1.75B，L6H5-C3D-6KG-1.75B，L6H5-C3D-8KG-1.75B，L6H5-C3D-10KG-1.75B，L6H5-C3D-20KG-1.75B，L6G-C3-50KG-3G6，L6G-C3-100KG-3G6，L6G-C3-150KG-3G6，L6G-C3-200KG-3G6，L6G-C3-250KG-3G6，L6G-C3-300KG-3G6，L6G-C3-500KG-3G6，L6G-C3-600KG-3G6，L6G-C3-50KG-3G6，L6G-C3-100KG-3G6，L6G-C3-150KG-3G6，L6G-C3-200KG-3G6，L6G-C3-250KG-3G6，L6G-C3-300KG-3G6，L6G-C3-500KG-3G6，L6G-C3-600KG-3G6，L6F-C3-50KG-3B6,L6F-C3-100KG-3B6,L6F-C3-150KG-3B6,L6F-C3-200KG-3B6,L6F-C3-250 KG-3B6,L6F-C3-500KG-3B6,L6F-C3-750KG-3B6,L6F-C3-1.0T-3B6,L6F-C3-2.0T-3B6,L6F-C 3D-50kg-3G,L6F-C3D-100kg-3G, /zemicL6F-C3D-150kg-3G,L6F-C3D-200kg-3G,L6F-C3D-250kg-3G,L6F-C3D-500kg-3G,L6F-C3D-7 50kg-3G,L6F-C3D-1000kg-3G,L6F-C3D-2000kg-3G,L6B-C3D-0.3KG-0.45B,L6B-C3D-0.6KG-0.45B,L6B-C3D-1.2KG-0.45B ,L6B-C3D-3KG-0.45B B6E-C3-100KG-2B,B6E-C3-150KG-2B,B6E-C3-200KG-2B,B6E-C3-300KG-2B,B6Q-C3-200KG-1.5B6,B6Q-C3-250KG-1.5B6,B6N-C3-15kg-1B6,B6N-C3-20kg-1B6,B6N-C3-30kg-1B6,B6N-C3-50kg-1B6,B6N-C3-75kg-1B6,B6N-C3-100kg-1B6,B6N-C3-150kg-1B6,B6N-C3-200kg-1B6,H6G-C3-100KG-3B6,H6G-C3-150KG-3B6,H6G-C3-200KG-3B6,H6G-C3-250KG-3B6,H6G-C 3-300KG-3B6,H6G-C3-500KG-3B6,H6G-C3-600KG-3B6,B6F-C3-100KG-3B6,B6F-C3-150KG-3B6,B6F-C3-200KG-3B6,B6F-C3-250KG-3B6,B6F-C3-5 00KG-3B6,B6F-C3-750KG-3B6,B6F-C3-1.0T-3B6,B6F-C3-2.0T-3B6,L6W-C3-50KG-3G6,L6W-C3-75KG-3G6,L6W-C3-100KG-3G6,L6W-C3-150KG-3G6,L6W-C3-200KG-3G6,L6W-C3-250KG-3G6,L6W-C3-500KG-3G6,L6W-C3-635KG-3G6,Zemic 称重传感器双剪切梁式特,性：◆Zemic 可满足10t～50t量程范围内的精确测量。

称重传感器有哪些品牌？
1、美国VISHAY称重传感器
-美国Tedea-Huntleigh
-美国celtron
-美国vishay nobel
-美国vishay BLH
-美国Revere
-美国Sensortronics 2、美国称重传感器
-美国Transcell
-美国MKCELLS
-美国ZEMIC
-美国AC
-美国RICELAKE
-美国Load Cell Central
-美国Hmcells
3、德国称重传感器
-德国HBM
-德国Sartorius/赛多利斯
-德国FLINTEC/富林泰克
-德国TECSIS
-德国SOEMER
4、瑞士称重传感器
-METTLER托利多
-瑞士FMS
5、西班牙称重传感器
-西班牙Utilcell
-西班牙Sensocar
6、韩国称重传感器
-韩国Bongshin/奉信
-韩国Dacell
-韩国CAS
7、日本称重传感器
-日本NMB(Minebea美蓓亚)
-日本NTS
-日本大和YAMATO
-日本艾安得A&D
-UNIPULSE尤尼帕斯
8、意大利称重传感器,仪表
-意大利狄纳乔Dini Argeo
-意大利Laumas
-意大利NBC
-意大利AEP
-意大利ADOS
-意大利CELMI（塞米）
9、国内知名品牌称重传感器,仪表
-宁波柯力
-广测GUANGCE
-珠海志美CHIMEI
-上海耀华。

进口称重传感器广州南创谭工德国HBM称重传感器、压力、扭矩传感器及仪表、TEDEA-HUNTLEIGH称重传感器、瑞士METTLER TOLEDO称重传感器、西班牙Utilcell称重传感器、美国Celtron 称重传感器系列、美国Amcells称重传感器、美国RICE LAKE称重传感器、美国Nobel张力传感器、美国Sensortroncs(STS)称重传感器、美国KELI称重传感器、美国Transcell称重传感器及仪表系列、美国BLH过程测量控制系统、荷兰PHILIPS称重传感器、美国Interface称重传感器、ZEMIC称重传感器、日本NMB 称重传感器、日本A&D传感器、日本ASAHI隔离端子及数字面板表、压力传感器及仪表系列、美国MSI压力传感器、美国MEAS压力传感器及位移传感器、美国Motorola 压力传感器、韩国DACELL称重传感器、韩国CAS传感器、韩国Bongshin 称重传感器、韩国SETech传感器、美国Freescale汽车用传感器、美国AmCells A称重传感器、德国Sartorius称重传感器、德国FLINTEC传感器及仪表、德国NOVOtechnik位移传感器、意大利Laumas称重传感器及其仪表、英国Omega传感器、法国Master-K称重传感器及其显示器等世界著名公司的品牌产品。

产品广泛用于航空航天、化纤、机械、能源、交通建筑、钢铁、环保、制药、矿山、建筑机械、给水排水、石油天然气、化工冶金、水利电力、热力造纸、市政管理等领域中的电子秤、汽车衡、配料秤、全电子汽车衡、电子地上衡电子台秤、电子吊称、定量包装系统。

进口称重传感器光电池是利用光生伏特效应把光能直接转变成电能的器件，Mettler Toledo称重传感器在有光照情况下就是一个电源。

传感器由于它广泛应用于把太阳能直接变为电能，因此又称为太阳能电池。

进口称重传感器光电池的种类很多，NMB称重传感器以其半导体材料加以区别，如硒光电池、锗光电池、硅光电池、氧化亚铜光电池、砷化稼光电池、磷化稼光电池等。