下载文档原格式
TSC-100凯丰电子台秤说明书
关于凯丰家用电子秤说明书的具体解答如下：
1、检查：水平、电源、干燥剂。
2、校准：清盘，按（T）去皮键，使天平显示为0.0000g，按（CAL）校准键，天平显示“C”和占用符号“0”，此时将自校砝码置于秤盘上，等待显示自校砝码值，并发出“嘟”声，天平校准完毕，并自动回复到称量状态。
3、让称盘空载单击“ON”键，天平显示自检，待天平稳定30min 后进行称重。
4、简单称量：样品放在称盘上，显示值即为物品的重量。
待数字稳定后读取称量结果。
5、去皮：将空容器放在天平称盘上，显示其重量值，单击去皮键，显示值回复到0.0000g，向空容器中加料，并显示净重值。
天平显示“O”表示微处理机正在进行工作，请耐心等待。
6、取出样品，切勿将样品散落在天平内。
7、关机：恢复零点平衡，按住“OFF”键。
8、关闭电源。
(19)中华人民共和国国家知识产权局(12)发明专利申请(10)申请公布号 (43)申请公布日 (21)申请号 201910938709.9(22)申请日 2019.09.30(71)申请人 梅特勒-托利多(常州)测量技术有限公司地址 213125 江苏省常州市新北区太湖西路111号申请人 梅特勒-托利多(常州)精密仪器有限公司 梅特勒-托利多国际贸易（上海）有限公司(72)发明人 朱顺康 胡万川 徐建飞 孙徐 扎伊德·萨伊德 (74)专利代理机构 上海专利商标事务所有限公司 31100代理人 陈亮(51)Int.Cl.G01G 21/02(2006.01)G01G 21/28(2006.01)(54)发明名称称重传感器组件及包括其的动态自动检重秤(57)摘要本发明提供了一种称重传感器组件及包括其的动态自动检重秤，所述称重传感器组件包括传感器上支撑板、分离式罩壳、称重传感器、传感器下支撑板和电机电缆，分离式罩壳的上端部与传感器上支撑板固定连接，分离式罩壳的下端部与传感器下支撑板固定连接，称重传感器固定在分离式罩壳内；称重传感器一端的上部与传感器上支撑板连接，另一端的下部与传感器下支撑板连接；电机电缆由分离式罩壳的上部穿入，下部穿出，且位于分离式罩壳内的电机电缆部分为分离式线缆，分离式线缆与称重传感器之间始终存在间隙且分离开来。
本发明称通过嵌入式的罩壳结构设计，降低外界粉尘、气流等环境因素对传感器的干扰，提升了传感器的防护等级。
权利要求书2页 说明书7页 附图8页CN 112577584 A 2021.03.30C N 112577584A1.一种称重传感器组件，其特征在于，所述称重传感器组件包括传感器上支撑板、分离式罩壳、称重传感器、传感器下支撑板和电机电缆，所述分离式罩壳的上端部与所述传感器上支撑板固定连接，所述分离式罩壳的下端部与所述传感器下支撑板固定连接，所述称重传感器固定在所述分离式罩壳内；所述称重传感器一端的上部与所述传感器上支撑板连接，另一端的下部与所述传感器下支撑板连接；所述电机电缆由所述分离式罩壳的上部穿入，下部穿出，且位于所述分离式罩壳内的所述电机电缆部分为分离式线缆，所述分离式线缆与所述称重传感器之间始终存在间隙且分离开来。
特征与运用拉伸：S-称重传感器S-传感器最大称量值：50,100,200,300,500,1000kg,2,3,5t装备选项：TSC称重传感器拉伸采用镀镍合金钢金属机体材质保护等级具有IP65；合金钢罐装结构规格：TSC/TSB –合金钢罐装结构TSC称重传感器可选仪器应用领域：Mettler Toledo TSC-50kg 称重传感器适用于经济型悬浮漏斗称，且可选仪表；产品各项技术指标TSC额定容量50,100,200,300,500,1000 kgTSB额定容量2,3,5 tTSC称重传感器灵敏度mV/V 2 ± 0.002不重复性%R.O. ± 0.01滞后%R.O. ≤±0.02非线性%R.O. ≤± 0.02蠕变(30 分) %R.O. ≤±0.02TSC称重传感器工作温度范围C -20~+65灵敏度温度系数%Load/ C ≤±0.002零点温度系数%R.O./ C ≤± 0.002零点输出%R.O. ≤± 1温度系数C -10~+40输入阻抗Ω 381 ± 4输出阻抗Ω 350 ± 1绝缘电阻MΩ ≥5000(直流50V)建议激励电压V(DC/AC) 5～15最大激励电压V(DC/AC) 20安全过载%R.C. 150极限过载%R.C. 300托利多TSC称重传感器防护等级IP65(TSC), IP67(TSB)TSC称重传感器电缆长度5m产品安装要点1、安装传感器的底座安装面应平整、清洁，无任何油膜，胶膜等存在。
安装底座本身应有足够的强度和刚性，一般要求高于传感器本身的强度和刚度。
2、称重传感器要轻拿轻放，尤其是由合金铝制作弹性体的小容量传感器，任何冲击、跌落，对其计量性能均可能造成极大损害。
对于大容量的称重传感器，一般来说，它具有较大的自重，故而要求在搬运、安装时，尽可能使用适当的起吊设备（如手拉葫芦、电动葫芦等）。
传感器输出的三种常见信号和接线形式传感器已经被大家广为熟悉，大家都传感器的输出信号也大致了解了一下，从传感器输出信号形式可以分为三种分别是增量码信号、绝对码信号以及开关信号。
，这三种信号有着各自的优点。
这三种信号又是什么意思呢？下面我们就来简单介绍一下。
MOD300-150kg称重传感器：h ttp://china.coove/busine ss1/detail/17574417.htmlMOD340-75kg称重传感器：http://china.coove/busine ss1/detail/17574532.htmlMOD460-20t称重传感器：http://china.coove/busine ss1/detail/17574713.htmlMOD460-100t称重传感器：http://china.coove/busine ss1/detail/17574807.htmlMOD540-10t称重传感器：http://china.coove/busine ss1/detail/17575015.htmlMOD700-60t称重传感器：http://china.coove/busine ss1/detail/17575117.htmlMOD740-20t称重传感器：http://china.coove/busine ss1/detail/17575238.htmlMOD740-40t称重传感器：http://china.coove/busine ss1/detail/17575321.htmlMOD740-200t称重传感器：http://china.coove/busine ss1/detail/17575392.htmlMOD740-400t称重传感器：http://china.coove/busine ss1/detail/17575501.htmlMOD750-10t称重传感器：http://china.coove/busine ss1/detail/17575599.htmlBCH-5t称重传感器：http://china.coove/busine ss1/detail/17575783.htmlCBES-500kg称重传感器：h ttp://china.coove/busine ss1/detail/17576070.htmlCBES-1t称重传感器：http://china.coove/busine ss1/detail/17576211.htmlCBES-2t称重传感器：http://china.coove/busine ss1/detail/17576303.htmlCBES-5t称重传感器：http://china.coove/busine ss1/detail/17576342.htmlCBES-10t称重传感器：http://china.coove/busine ss1/detail/17576392.htmlCBFS-100kg称重传感器：h ttp://china.coove/busine ss1/detail/17576471.htmlCSCK-30T称重传感器：http://china.coove/busine ss1/detail/17576686.htmlCSCK-100T称重传感器：http://china.coove/busine ss1/detail/17576751.htmlCDFS-50KG称重传感器：http://china.coove/busine ss1/detail/17576961.htmlCDFS-200kg称重传感器：h ttp://china.coove/busine ss1/detail/17576991.html增量码信号的特点是，被测量值与传感器输出信号的变化周期数成正比，即输出量值的大小由信号变化的周期数的增量决定。
梅特勒托利多称重传感器简介梅特勒托利多（Mettler Toledo）是一家专门从事测量和分析仪器的瑞士公司，是全球称量技术的领导者之一。
梅特勒托利多生产的称重传感器，以其精确、可靠的性能而被全球各行各业广泛应用。
原理梅特勒托利多的称重传感器可分为两类：电子称重传感器和机械式称重传感器。
电子称重传感器电子称重传感器采用应变片或压电陶瓷作为传感元件，通过电子电路转化为输出信号。
这种传感器通常具有较高的灵敏度和可靠性，能够在工业生产过程中实现高精度的重量测量。
机械式称重传感器机械式称重传感器采用弹性体或权重坠子作为传感元件，通过机械结构转化为输出信号。
这种传感器通常具有较高的机械稳定性和耐用性，但精度较低，只适合进行粗略的重量测量。
应用领域梅特勒托利多的称重传感器广泛应用于工业生产、实验室、医疗和交通等领域。
工业生产梅特勒托利多的称重传感器可以用于各种重量测量场合，如压力容器、货车秤等。
实验室梅特勒托利多的称重传感器被广泛应用于实验室中，如天平、分析仪器等。
医疗梅特勒托利多的称重传感器可以用于医疗设备中，如体重秤、血槽秤等。
交通梅特勒托利多的称重传感器可以用于交通设备中，如大型卡车称重、电子收费等。
特点梅特勒托利多的称重传感器具有以下几个特点：精度高梅特勒托利多的称重传感器精度高，可以实现高精度的重量测量。
可靠性强梅特勒托利多的称重传感器可以长期稳定工作，具有较高的可靠性。
维护方便梅特勒托利多的称重传感器结构简单，维护方便，使用寿命长。
结论梅特勒托利多的称重传感器是一种精密、可靠的测量设备，在各个领域都有广泛的应用。
随着科技的发展，梅特勒托利多将会进一步提高称重传感器的性能和可靠性，为全球的称量技术发展做出更大的贡献。
称重传感器原理及常见故障解决方法 梅特勒-托利多（常州）精密仪器有限公司 冯志辉【摘 要】称重传感器实际上是一种将质量信号转变为可测量的电信号输出的装置，其工作原理是把加到秤盘上的物体重量转换成与该重量成比例的电信号，然后将输出的电信号放大和A/D转换后由相关电路显示出称重信息。
其中电阻应变式称重传感器由于其结构较简单，准确度高，适用面广，稳定性强，且能够在相对比较差的环境下使用，因此在衡器中得到了广泛地运用。
本文就电阻应变式称重传感器的应用故障进行了一些探讨。
【关键词】称重传感器；放大；电阻应变；衡器Abstract: Load cell is a device to convert a quality signal into a measurable electrical signal, its working principle is to convert a quality signal into an electrical signal proportional to the weight , then the output signal is showed after amplification and A/D conversion circuit . The resistance strain type load cell has been widely used in the scale due to its simple structure, high accuracy, wide application range, strong stability, and can be in a relatively poor environment. We will discuss the resistance strain load cell application in this paper.Key words: load cell；amplify；resistance strain；scale1 引言在现代工业生产尤其是自动化生产过程中，首先要解决的就是要获取准确可靠的信息，这就需要用各种传感器来监视和控制生产过程中的各个参数，使设备工作在正常状态或最佳状态，并使产品达到最好的质量。
tsc-1000kg,TSC-1000kg,TSC称重传感器参考资料tsc拉式S型称重传感器产品型号产品描述TSC-50kg钢质拉式传感器，容量50KG，适用于吊钩秤，试验机，悬浮仓TSC-100kg钢质拉式传感器，容量100KG，适用于吊钩秤，试验机，悬浮仓TSC-200kg钢质拉式传感器，容量200KG，适用于吊钩秤，试验机，悬浮仓TSC-300kg钢质拉式传感器，容量300KG，适用于吊钩秤，试验机，悬浮仓TSC-500kg钢质拉式传感器，容量500KG，适用于吊钩秤，试验机，悬浮仓TSC-1000kg钢质拉式传感器，容量1000KG，适用于吊钩秤，试验机，悬浮仓拉式称重传感器连接件产品型号产品描述TP-100～300配100～300KG TSC,拉杆式TP-500～1000配500～1000KG TSC,拉杆式ZP-100～300配100～300KG TSC,关节轴承式ZP-500～1000配500～1000KG TSC,关节轴承式tsc称重传感器安装尺寸tsc料罐/料仓/定量打包秤专用仪表IND331/IND131系列称重仪表称重终端面板式IND33133P100000000000称重仪表IND33133P10000B000000称重仪表IND33133P100000D00000称重仪表IND33133P100000B00000称重仪表IND33133P100000A00000称重仪表IND33133P100000P00000称重仪表称重终端防尘式IND33133H100000000J00称重仪表IND33133H100000D00J00称重仪表IND33133H100000B00J00称重仪表IND33133H100000A00J00称重仪表IND33133H100000P00J00称重仪表称重终端导轨式IND13113D100000000000称重仪表IND13113D100000D00000称重仪表IND13113D100000B00000称重仪表IND13113D100000P00000称重仪表IND13113D100000K00000称重仪表IND131接线盒式IND13113B100000000000称重仪表IND13113B10000B000000称重仪表IND13113B100000D00000称重仪表IND13113B100000B00000称重仪表IND13113B100000A00000称重仪表IND13113B100000P00000称重仪表IND13113D100000K00000称重仪表IND245系列称重仪表TSC称重终端普通型IND245245G13000010J00称重仪表IND245245G14000010J00称重仪表IND245245G13001010J00称重仪表IND245245G14001010J00称重仪表IND245245G13002010J00称重仪表IND245245G13003010J00称重仪表IND245245G13004010J00称重仪表IND245245G13010010J00称重仪表IND245245G13011010J00称重仪表IND245245G10001130J00称重仪表IND245245G10002130J00称重仪表IND245245G10011130J00称重仪表IND245245G10012130J00称重仪表称重终端防尘型IND245245H13000010J00称重仪表IND245245H14000010J00称重仪表IND245245H13001010J00称重仪表IND245245H14001010J00称重仪表IND245245H13002010J00称重仪表IND245245H13003010J00称重仪表IND245245H13004010J00称重仪表IND245245H13010010J00称重仪表IND245245H13011010J00称重仪表XK3123IND320专用仪表产品型号产品描述IND32032E100000000023称重仪表，基本型，防护等级IP65，土建筑和建筑路面机械IND32032E10000B000023称重仪表，配料型，防护等级IP65，土建筑和建筑路面机械IND32032E10000B001023称重仪表，减量法，防护等级IP65，土建筑和建筑路面机械IND32032E10000A000023称重仪表，模拟量，防护等级IP65，土建筑和建筑路面机械IND32032E10001B000023称重仪表，配料型，防护等级IP65，土建筑和建筑路面机械IND32032E100000C00023称重仪表，基本型，canopen接口，土建筑和建筑路面机械IND32032E10000BC00023称重仪表，配料型，canopen接口，土建筑和建筑路面机械tsc称重传感器技术指标。
托利多电子秤完整操作手册一、托利多电子秤简介托利多电子秤是一种高精度、高性能的称重设备，广泛应用于商业零售、工业生产、物流仓储等领域。
它具有称重准确、操作简便、功能丰富等优点，能够满足不同用户的需求。
二、托利多电子秤的组成部分1、秤体托利多电子秤的秤体通常由坚固的金属材料制成，具备良好的稳定性和耐用性。
2、称重传感器这是电子秤的核心部件，负责将物体的重量转化为电信号。
3、显示屏用于显示称重结果、商品信息等数据。
4、操作按键包括数字键、功能键等，方便用户进行操作和设置。
5、电源一般有市电供电和电池供电两种方式。
三、托利多电子秤的基本操作1、开机按下电源按钮，电子秤会进行自检，自检完成后进入称重状态。
2、置零在没有放置物品时，按下“置零”键，使秤的显示值为零。
3、称重将待称物品放置在秤盘上，显示屏会显示物品的重量。
4、去皮如果需要去除容器的重量，可以先将容器放在秤盘上，按下“去皮”键，然后再放入物品进行称重，显示屏显示的将是物品的净重。
四、托利多电子秤的功能设置1、单位切换可以通过设置键选择不同的重量单位，如千克、克、磅等。
2、小数点位数设置根据实际需求，设置称重结果显示的小数点位数。
3、打印设置如果电子秤连接了打印机，可以设置打印的格式、内容等。
4、密码保护为了防止误操作或未经授权的修改，可以设置密码保护相关设置。
五、托利多电子秤的校准为了确保称重的准确性，定期校准电子秤是非常重要的。
校准的方法通常有以下几种：1、外部砝码校准使用标准的砝码进行校准，按照电子秤的操作提示进行操作。
2、内部校准部分托利多电子秤具有内部校准功能，可在特定条件下自动进行校准。
六、托利多电子秤的数据管理1、数据存储电子秤可以存储一定数量的称重数据，方便查询和统计。
2、数据传输通过数据线或无线连接，可以将称重数据传输到电脑等设备进行进一步处理。
七、托利多电子秤的维护与保养1、清洁定期使用干净的湿布擦拭秤体和显示屏，保持清洁。
Q u i c k G u i d eACT100/ACT100xx Weight TransmitterACT100 Quick GuideIntended UseYour weighing transmitter is used for weighing. Use the scale exclusively for this purpose. Any other type of use and operation beyond the limits of technical specifications without written consent from Mettler-Toledo, LLC will invalidate its warranty.It is essential for the buyer to closely observe the installation information, product and system manuals, operating instructions and other documentation and specifications. MT’s warranty and any liability are expressly excluded for damages caused by non-compliance with the applicable manuals.DocumentationFor further details on system configuration and operation, refer to the documents provided on/ind-act100-downloads.Safety WarningsRead the Installation section on ACT100/ACT100xx User Guide before operating or servicing this equipment, follow all instructions carefully, and SAVE all documentation for future reference.WARNINGSFOR CONTINUED PROTECTION AGAINST SHOCK HAZARD CONNECT TO PROPERLY GROUNDED OUTLET ONLY. DO NOT REMOVE THE GROUND PRONG.WHEN THIS EQUIPMENT IS INCLUDED AS A COMPONENT PART OF A SYSTEM, THE RESULTING DESIGN MUST BE REVIEWED BY QUALIFIED PERSONNEL WHO ARE FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF ALL COMPONENTS IN THE SYSTEM AND THE POTENTIAL HAZARDS INVOLVED. FAILURE TO OBSERVE THIS PRECAUTION COULD RESULT IN BODILY HARM AND/OR PROPERTY DAMAGE.ALL EQUIPMENT MUST BE INSTALLED IN ACCORDANCE WITH THE INSTALLATION INSTRUCTIONS DETAILED IN THE USER MANUAL. INCORRECT OR SUBSTITUTE COMPONENTS AND/OR DEVIATION FROM THESE INSTRUCTIONS CAN IMPAIR THE SAFETY OF THE TRANSMITTER AND COULD RESULT IN BODILY HARM AND/OR PROPERTY DAMAGE.BEFORE CONNECTING/DISCONNECTING ANY INTERNAL OR EXTERNAL ELECTRONIC COMPONENTS, LOAD CELLS, HARNESSES OR INTERCONNECTING WIRING BETWEEN ELECTRONIC EQUIPMENT ALWAYS REMOVE POWER AND WAIT AT LEAST THIRTY (30) SECONDS BEFORE ANY CONNECTIONS OR DISCONNECTIONS ARE MADE. FAILURE TO OBSERVE THESE PRECAUTIONS COULD RESULT IN BODILY HARM AND/OR PROPERTY DAMAGE.DO NOT INSTALL, DISCONNECT OR PERFORM ANY SERVICE ON THIS EQUIPMENT BEFORE POWER HAS BEEN SWITCHED OFF AND THE AREA HAS BEEN SECURED AS NON-HAZARDOUS BY PERSONNEL AUTHORIZED TO DO SO BY THE RESPONSIBLE PERSON ON-SITE.THE ACT100 IS NOT INTRINSICALLY SAFE! DO NOT USE IN HAZARDOUS AREAS CLASSIFIED AS DIVSION 1 AND DIVISION 2, ZONE 0, ZONE 20, ZONE 1, ZONE 2 OR ZONE 21 BECAUSE OF COMBUSTIBLE OR EXPLOSIVE ATMOSPHERES.IN ORDER TO INSTALL THE DIVISION 2 APPROVED ACT100 TRANSMITTER UTILIZING THE U.S. APPROVAL, METTLER TOLEDO CONTROL DRAWING 30565571 MUST BE FOLLOWED WITHOUT EXCEPTION. IN ORDER TO INSTALL THE CATEGORY 3 MARKED ACT100 UTILIZING THE EUROPEAN APPROVAL, THE FM APPROVAL CERTIFICATE FM19ATEX0213X/ IECEx_FMG_19.0043X AND ALL LOCAL REGULATIONS MUST BE FOLLOWED WITHOUT EXCEPTION. FAILURE TO DO SO COULD RESULT IN BODILY HARM AND/OR PROPERTY DAMAGE. REFER TO THE ACT100 DIVISION 2 AND ZONE 2/22 INSTALLATION GUIDE 30562232 FOR ADDITIONAL INFORMATION.2 METTLER TOLEDO ACT100/ACT100xx Quick Quide 30540089| 001 | 07/2020Physical DimensionsFront Panel and Display FeaturesUp/Down Arrow Keys Navigation/Used for data entryEnter Enter key /Zero scale/Enter Operator menuLeft Arrow Key Switch position/ReturnWeight Display 000000 Displays weight information~ Motion, weight is currently changingB/G Gross ModeKG/G/LB Weight Display UnitSCL Scales status: On okay, flashing indicates scale errorPWR Power status: On okay, Off errorAO Analog Output status: On okay, flashing indicates out-of-range errorDEV Device status: On okay, flashing contact serviceBottom DIP Switch4 METTLER TOLEDO ACT100/ACT100xx Quick Quide 30540089| 001 | 07/2020Common Errors Shown on DisplayOvercapacity Weight overload. The weight display shows: Undercapacity Weight underload. The weight display shows:Power-up ZeroFailOut of Power-up Zero range. The weight display shows: or30540089| 00 | 07/2020 METTLER TOLEDO ACT100/ACT100xx Quick Guide 56METTLER TOLEDO ACT100/ACT100xx Quick Quide30540089| 001 | 07/2020Keypad Operator Menu StructureThe operator setup functionality via keypad is limited. Full configuration is possible via Webserver.Enter operator menu: Long Press ENTER . Use UP and DOWN keys to switch between menu icons. Use ENTER key to enter the next level menu and LEFT key to return to previous level. InformationModelACT100Terminal SN ############ S/W Version #.##.#####.## IP Address###.###.###.### MAC Address##:##:##:##:##:## /ind- act100-downloads On/Off X10 resolutionSwitch ON/OFF X10 resolution, leave menuSet ComparatorsLimit 1..5Input value with keypadTest & AdjustmentGeo Input Geo CodeLinearity Input - None, 3 point, 4 point, 5 point Set Zero Empty Scale, then Press Enter Set Span Add test weight to scaleInput test weight value, then press Enter Continue if linearization selected Step CalibrationInput test weightAdd test weight to scale, press Enter Remove test weight Fill load to former levelAdd test weight to scale, press Enter Finish with Left-Arrow keyCalFreePerform calibration without test weights Display Error MessagesList of current error messagesLanguageSelect language for HMI displayInput-English, ChineseSetupCapacity & Incr. Input scale unit Input scale capacity Input scale incrementCalibration Refer to above “Test & Adjustment” FilterLimit Frequency – 1-20 Hz Weighing mode EnvironmentAnalog Output Input source – Display Wt. or Gross Wt.Output Range – current output or voltageoutput(None, 0~5V, 0~10V, 4~20mA,0~20mA or 0~24mA)Analog Zero Value – ###### kgAnalog Span Value – ###### kgCalibrate Output – Adjust analog signalvalue for Analog Zero and Span outputWebserver Webserver: Enable or DisableIP Address: ###.###.###.###Subnet Mask: ###.###.###.### 30540089| 00 | 07/2020 METTLER TOLEDO ACT100/ACT100xx Quick Guide7WebserverThe webserver is an easy-to-use tool that is the primary configuration/maintenance tool for ACT100/ACT100xx. There is no need to install additional software. It is only necessary to have a web browser (IE, Chrome, Firefox or Safari) on your PC or Laptop. If the ACT100/ACT100xx and your PC are in the same network, the ACT100 webserver can be accessed by inputting the ACT100/ACT100xx IP address (default 192.168.0.2) in the address bar of web browser.A Webserver example is shown below. For more details, please refer to the ACT100/ACT100xx User Guide.8 METTLER TOLEDO ACT100/ACT100xx Quick Quide 30540089| 001 | 07/202030540089| 00 | 07/2020METTLER TOLEDO ACT100/ACT100xx Quick Guide9Analog OutputACT100/ACT100xx provides two types of analog output signals: a current output signal or a voltage output signal. This can be selected via the “Output Type” submenu in the Webserver or local menu. Below is an example of the selection “4~20mA”. Please note ACT100/ACT100xx has separate pins for current output (IOUT and IGND) and voltage output (VOUT and VGND).For example, if the Output Type is set as 4~20 mA, Analog Zero Value as 0 kg and Analog Span Value as 3,000 kg, ACT100/ACT100xx will output 4 mA when the scale is empty (0 kg) and 20 mA when 3,000 kg load is on the scale. In this case, when live weight exceeds 3,000 kg, the analog output signal will jump from 20 mA to 24 mA as a warning to the DCS/PLC.The analog output signal can be calibrated via the Analog Output Adjustment submenu. ACT100/ACT100xx can increase or decrease the analog signal via two levels of adjustment (Coarse and Fine adjustment).10METTLER TOLEDO ACT100/ACT100xx Quick Quide30540089| 001 | 07/2020Errors Messages Shown on DisplayError value ACT100 Display DescriptionAction009 “Board info. Err” Hardware production information error Cycle power; call MT Service if issue persists010 “Calib. Block err” Calibration block data error; block data is lost Perform master reset Re-calibrate011 “Scale block err” Scale block data error Perform master resetPerform setup for scale block 012 “Term. Block err” Transmitter block data errorPerform master resetPerform setup for transmitter block 013 “APP. Block err” Application block data errorPerform master resetPerform setup for application block 014 “COM. Block err” Communication block data errorPerform master resetPerform setup for communication block015 “Maint. Block err” Statistics block data errorPerform master resetPerform setup for maintenance block 016 “Analog system A/D fail”Lost analog signal;abnormal functioning of scaleCall MT Service 018 “Zero failed Motion” Zero failed due to scale isin motionWait scale to be stable019 “Zero failed Net mode” Zero failed due to scale isin Net modeAttempt to Zero after Clear operation is performed020 “Zero failed/Out of range” Weight out of zero range Unload scale and perform Zero again 021 “Zero failed Zero disabled” Zero attempted whenfunction disabled in Setup menuEnable Zero function in Setup menu 022 “Tare failed Motion” Tare failed due to scale is inmotionWait scale to be stable029 “Tare failed Zero not captured” Tare failed due to Power-up Zero is not captured Capture the Power-up Zero or disable Power-up Zero before Tare 030 “Tare Failed, over capacity” Tare failed due to scalebeing over capacity Unload weight on scale untilovercapacity is cleared and perform Tare again031 "Tare failed Negative value"Tare failed due to current gross weight is negative Adjust the weight on scale to make gross weight positive035 "Analog saturation" A/D converter in overloadCheck the input signal(should be between 0mV and 20mV)or call MT Service036 "Factory zero not done" Factory Zero calibration notperformedCall MT Service037 "Factory span not done" Factory Span calibration not performedCall MT Service050"LC Connection Error"Lost connection between ACT100 and LCCheck the LC and connection cablesCleaning the TransmitterUse a soft, clean cloth and mild glass cleaner. Do not spray cleaner directly onto transmitter. Do not use industrial solvents such as acetone.Disposal of Transmitter / WEEE InformationIn conformance with the European Directive 2002/96/EC on Waste Electrical and Electronic Equipment Array (WEEE) this device may not be disposed of in domestic waste. This also applies to countries outside the EU,per their specific requirements.Please dispose of this product in accordance with local regulations at the collecting point specified forelectrical and electronic equipment.If you have any questions, please contact the responsible authority or the distributor from which youpurchased this device.Should this device be passed on to other parties (for private or professional use), the content of thisregulation must also be related.Thank you for your contribution to environmental protection.30540089| 00 | 07/2020 METTLER TOLEDO ACT100/ACT100xx Quick Guide11To protect your METTLER TOLEDO product’s future: Congratulations on choosing the quality and precisionof METTLER TOLEDO. Proper use according to these instructions and regular calibration and maintenanceby our factory-trained service team ensure dependableand accurate operation, protecting your investment.Contact us about a METTLER TOLEDO serviceagreement tailored to your needs and budget.We invite you to register your product at/productregistration so we can contactyou about enhancements, updates and important notifications concerning your product.For more informationMettler-ToledoIm Langacher 44 8606 Greifensee SwitzerlandPhone +41449442011 Mettler-Toledo, LLC30540089 Rev. 01, 07/2020。
