BSC6900快速开局指导书

BSC6900SAU 调测步骤1、更改本地PC的IP地址为192.168.6.55（SAU默认调测IP为192.168.6.50），用putty登陆SAU,PING 通SAU的IP，退出putty2、在D盘根目录下创建文件夹SAUV600R008C01，并将sau.tar文件放置到该目录下3、使用psftp与SAU建立连接（打开psftp软件，在ftp>后输出open IP（192.168.6.50）”）4、输入以下命令，登录本地D盘lcd D:\5、输入以下命令，查询SAU上是否存在安装目录。

ls /mbsc/upgrade提示“no such file or directory”信息，表示不存在“/mbsc/upgrade”目录提示“/mbsc/upgrade”目录相关信息，表示已存在“/mbsc/upgrade”目录如果不存在输入以下命令在SAU上创建安装目录。

mkdir /mbsc/upgrade6、输入以下命令，切换至SAU安装目录。

cd /mbsc/upgrade7、输入以下命令，执行文件夹上传操作。

put -r SAUV600R008C018、待文件上传完毕后，通过执行ls命令检查文件上传结果。

ls /mbsc/upgrade/SAUV600R008C01如果该目录下存在“sau.tar.gz”文件，且文件大小(85353101)与上传前一致，说明上传成功。

9、putty登陆SAU切换目录至安装程序所在路径# cd /mbsc/upgrade/SAUV600R008C0110、解压缩SAU安装程序# tar -xzf sau.tar.gz11、切换至解压缩后的目录# cdsau12、输入以下命令，执行“install_sau”脚本，按“Enter# ./install_sau 根据提示选择相应的类型，版本，补丁，语言版本时选择chs13、界面提示如下：Please affirm input information. input Y to continue; input E to exit. ->选择Y，进入安装SAU应用程序当界面提示Install SAU succeed!时，表示SAU应用程序安装成功。

BSC6900下DBS3900 RRU共小区实施方案小结一、RRU多站点共小区基本原理RRU多站点共小区技术基于分布式基站DBS3900架构开发，通过RRU拉远，一个站点下的多个物理小区（称之为：位置组subsite）分属不同的物理地址，但是逻辑上属于同一个小区。

每个subsite的载频数、频点、信道配置、CGI等小区级的参数配置为相同（载波的输出功率可以根据实际情况进行微调）。

如图1所示：蓝色区域为每个subsite覆盖的区域，多个subsite同属于一个小区CellA。

图1RRU多站点共小区示意图主、从subsite的设定在BSC维护台上可以设置任意一个subsite为主subsite（如果不设置，则默认第一个添加的subsite为主subsite），一旦主subsite确认后，其余的subsite则是从subsite。

主subsite的TRX完成所有业务功能，包括：小区的管理，业务的控制等；从subsite接收调制数据或者将上行解调后数据传送到主subsite。

主subsite和从subsite之间的数据交换都需要通过BBU来完成。

数据处理方式下行处理方式：主subsite的TRX将当前时隙的调制信号，通过CPRI光纤送到BBU交换到每个subsite对应的TRX 时隙上，对于BCCH、PDCH信道是所有的subsite都发射相同的信号，TCH信道可以是其中两个subsite的服务TRX发射信号（选择的两个subsite分别是前一次服务的subsite和这次选择的最佳subsite）。

上行处理方式：每个subsite在所有时刻都保持接收状态，每个subsite 同时对当前时隙的上行信号进行解调预处理，将计算的信噪比、接收信号强度等值送到主Subsite对应TRX进行判断并选择服务的TRX（每20ms选择判断一次）。

选择服务TRX后，服务TRX对当前时隙信号进行正常解调，解调之后送到主subsite进行译码，完成整个通信过程。

BSC6900故障OMU单板更换操作指导1 背景介绍我司BSC6900 OMU单板采用Dopra Linux操作系统，较之之前BSC6810的windows 操作系统可视化差，操作维护命令多。

现有的更换单板操作指导书中相关操作命令描述不够细致，现场操作的时候只能从相关资料中查找汇总，如果出现OMU单板的故障，处理起来往往需要后方支持，增加了处理的难度和时间。

如果有相关的详细指导书，将每一个操作的具体命令包含在内，就可以帮助现场操作维护人员避免误操作和加快处理的进度。

同时，客户也可据此指导书自行更换，减少了对华为工程师的依赖，降低维护成本。

本指导书以OMU双机模式为例，结合现场更换经验，查阅汇总多个资料，总结了更换故障OMU单板的详细操作步骤和注意事项。

本指导书的IP规划以某局网络为例，更换单板为27槽，现场操作需要以现场客户的网络规划为准。

2 OMU组网实例OMU单板作为RNC的操作维护处理中心，是操作维护终端与RNC其他单板通信的桥梁，同时负责收集配置、性能、告警、日志等数据并通过OM网络提供LMT/M2000查询。

OMU单板一般配置在0框25,27槽位。

2.1 OMU单板的网卡配置一块OMU单板上共部署了6 块网卡。

为提高网络可靠性，将其中的4 块网卡分为 2 组进行两两绑定，分别用于OMU 和LMT/M2000 之间（定义为外网）、OMU 和BSC6900主机单板之间（定义为内网）通信。

OMU 上的6 块网卡分别为：ETH0 和ETH1：两块网卡绑定成外网网卡队列，即bond1/bond1:0，用于OMU 和LMT/M2000 通信。

●ETH2：作为OMU 的调试网卡，即bond2，必要时用于连接便携机进行OMU 调试●ETH3-UPDATE：作为OMU 的备份网卡，即bond3，在BSC6900 配置两块OMUa单板时用作主备OMU 之间专用的备份通道。

●ETH4-SCU7 和ETH5-SCU6：两块网卡绑定成内网网卡队列，即bond0（vlan1/vlan1:0），用于OMU 和BSC6900 主机单板通信。

ABCDown Quality 下行链路质量门限BSC6900SET GCELLHOAD(Optional)ABCUpQu ality 指配优选的上行链路质量门限BSC6900SET GCELLHOAD(Optional)ABCWaitM axTime 指配优选最大时长BSC6900SET GCELLHOAD(Optional)ABISBYPA SSMODE Abis旁路模式BSC6900ADD BTS(Optional)ABISFCEN SDCCH信道拥塞流量控制允许BSC6900SET GCELLCCCH(Optional)AbisFCTim er1Abis流控定时器1BSC6900SET BSCTMR(Optional)AbisFCTim er2Abis流控定时器2BSC6900SET BSCTMR(Optional)ABISIDLE TSALLOC 空闲时隙分配策略BSC6900SET BTSOTHPARA(Optional)ABISIDLETSCFGS WITCH 空闲时隙配置优化开关BSC6900SET BTSOTHPARA(Optional)AbisJamTh reshold2St artLs 启动BTS本地交换的Abis口拥塞门限BSC6900SET BSSLS(Optional)ABISRESA DJTCHHF UNSW Abis资源调整半速率功能开关BSC6900SET BTSFLEXABISPARA(Optional)ABISTSFR EETM Abis时隙释放定时器长度BSC6900SET GCELLPSCHM(Optional)AbisVer Abis接口阶段标识BSC6900SET BSCBASIC(Optional)ABLASTTI ME 基站搜集AB持续时间[100毫秒]BSC6900ADD AISSCFG(Optional)Abnormal MosThresh old 语音异常MOS分门限BSC6900SET OTHSOFTPARA(Optional)ACCBURS T 接入脉冲类型BSC6900SET GCELLPSBASE(Optional)ACCCONT ROLCLAS S 接入控制等级<16位位图>BSC6900SET GCELLPRACH(Optional)ACCCTRL EN ACC接入控制允许BSC6900SET GCELLCCBASIC(Optional)ACCCTRL PY ACC接入控制策略BSC6900SET GCELLCCBASIC(Mandatory)ACCESSO PTILAY 入局切换优选层BSC6900SET GCELLHOIUO(Optional)ACCINDE X ACC接入控制策略索引BSC6900ADD BSCACCCTRLP(Mandatory)AccStaSer viceType 分组域接入初始业务类型BSC6900SET GCELLPSOTHERPARA(Optional)ACCWPO S ACC接入控制窗口起始位置BSC6900ADD BSCACCCTRLP(Optional)ACCWSIZ E ACC接入控制窗口大小BSC6900ADD BSCACCCTRLP(Optional)ACCWSP ACC接入控制窗口滑动速度BSC6900ADD BSCACCCTRLP(Optional)ACFC 地址和控制域压缩BSC6900ADD PPPLNK(Optional)ADD MPGRP(Optional)ACFC 是否支持地址和控制域压缩BSC6900ADD BTSPPPLNK(Optional)ADD BTSMPGRP(Optional)IMP BTSPPPLNK(Optional)IMP BTSMPGRP(Optional)ACOOPERATPAGIN GSWITCH A口协作寻呼开关BSC6900SET BSCPSSOFTPARA(Optional)ACS 附加重选参数指示BSC6900SET GCELLIDLEAD(Optional)ACTCDSE TF AMR激活的语音编码集[全速率]BSC6900SET GCELLCCAMR(Optional)ACTCDSE TH AMR激活的语音编码集[半速率]BSC6900SET GCELLCCAMR(Optional)ACTCDSE TWB AMR激活的语音编码集[宽带]BSC6900SET GCELLCCAMR(Optional)ACTL2RE EST 激活L2重建BSC6900SET GCELLSOFT(Optional)ACTTIME 基站激活资源有效时间BSC6900ADD AISSCFG(Optional)ACVLTHD 交流电压告警下限BSC6900SET BTSAPMUBP(Optional)ACVOLAL ARMH 交流过压告警点BSC6900SET BTSDPMUBP(Optional)ACVOLAL ARML 交流欠压告警点BSC6900SET BTSDPMUBP(Optional)ACVUTHD 交流电压告警上限BSC6900SET BTSAPMUBP(Optional)ADAPTAS SIGNMEN TFLOW 小区内切换采用指配流程BSC6900SET GCELLSOFT(Optional)ADDR通信地址BSC6900SET BTSFMUABP(Optional) SET BTSAPMUBP(Optional) SET BTSDATUBP(Optional) SET BTSDEMUBP(Optional) SET BTSDHEUBP(Optional)AddTransB wInt 解拥塞状态副链路申请定时器时长BSC6900SET BSCPSSOFTPARA(Optional)AddTransB wNum 解拥塞状态申请副链路带宽BSC6900SET BSCPSSOFTPARA(Optional)ADEF 外部告警客户定义开关BSC6900SET BTSRXUBP(Optional)ADJBSCD PC 相邻BSC目的信令点BSC6900ADD EXTNCELL(Mandatory)COL BSCSYNCINFO(Mandatory)ADJMODE调整模式BSC6900SET BTSEXCURSION(Mandatory) SET BSCSYNCOFF(Mandatory)ADJUSTU LMCSTYP E EGPRS上行编码方式调整模式BSC6900SET GCELLEGPRSPARA(Optional)ADLDACT 自动加载激活开关BSC6900SET BTSAUTODLDACTINFO(Optional)ADMODE 自动加载模式BSC6900SET BTSAUTODLDACTINFO(Optional)ADMSTAT管理状态BSC6900SET GCELLADMSTAT(Mandatory) ADMSTAT管理状态BSC6900SET GTRXADMSTAT(Mandatory)ADMSTAT管理状态BSC6900SETGTRXCHANADMSTAT(Mandatory)ADTET 偏移时间调整终止时间BSC6900ADD AISSCFG(Optional)ADTLOD 偏移时间调整负荷门限BSC6900ADD AISSCFG(Optional)ADTON 偏移时间调整任务开关BSC6900ADD AISSCFG(Mandatory)ADTST 偏移时间调整起始时间BSC6900ADD AISSCFG(Optional)ADVALMM GRULETP 高级告警管理规则类型BSC6900ADD BTSALMMGMRULE(Mandatory)ADVER1基站软件版本1BSC6900SET BTSAUTODLDACTINFO(Optional)ADVER2基站软件版本2BSC6900SET BTSAUTODLDACTINFO(Optional)AEC_Echo _Path_Del ay AEC回波迟延处理范围BSC6900SET TCPARA(Optional)AEC_Echo _Return_L oss AEC默认回波返回损耗BSC6900SET TCPARA(Optional)AEC_Nlp_ Gate AEC NLP启动门限BSC6900SET TCPARA(Optional)AEC_Path _Delay AEC线路纯迟延BSC6900SET TCPARA(Optional)AEC_SNR _Gate AEC近端信噪比门限BSC6900SET TCPARA(Optional)AEC_Switc h AEC功能开关BSC6900SET TCPARA(Optional)AECDetect Threshold AEC优化检测门限BSC6900SET TCPARA(Optional)AECDetect Time AEC优化检测时间BSC6900SET TCPARA(Optional)AFRDSBL CNT AFR无线链路失效计数器BSC6900SET GCELLCCBASIC(Optional)AFRSAMU LFRM AFRSACCH复帧数BSC6900SET GCELLCCBASIC(Optional)AGPSREC EIVERID GPS接收机标识BSC6900ADD GPS(Mandatory)AGPSRECEIVERTYP E GPS接收机类型BSC6900ADD GPS(Mandatory)AHRDSBL CNT AHR无线链路失效计数器BSC6900SET GCELLCCBASIC(Optional)AHRSAMU LFRM AHRSACCH复帧数BSC6900SET GCELLCCBASIC(Optional)AID告警编号BSC6900SET ALMPORT(Mandatory) AID告警ID BSC6900SET ALMBLKPARA(Mandatory)AID告警ID BSC6900SET ALMLVL(Mandatory) SET ALMSHLD(Mandatory) SET BOXRPT(Mandatory)AID告警ID BSC6900ADD OBJALMSHLD(Optional)AID告警ID BSC6900SET ENVALMPARA(Mandatory) AID告警编号BSC6900SET BTSENVALMPORT(Optional) AID告警ID BSC6900ADD BTSOBJALMSHLD(Mandatory) AIDDELAYPROTECT TIME 小区互助保护延时BSC6900SET GCELLSOFT(Optional)AIDST 告警选择方式BSC6900ADD OBJALMSHLD(Optional)AIDST 告警选择方式BSC6900ADD BTSOBJALMSHLD(Mandatory)AInterMsg Trace 是否跟踪A接口消息[端到端用户跟踪]BSC6900SET OTHSOFTPARA(Mandatory)AINTFFCD ISCLUEN A接口流控允许流控位置更新BSC6900SET BSCFCPARA(Optional)AINTFFCD ISCMOCE N A接口流控允许流控主叫BSC6900SET BSCFCPARA(Optional)AINTFFCD ISCMTCE N A接口流控允许流控被叫BSC6900SET BSCFCPARA(Optional)AINTFFCD ISCOSEN A接口流控允许流控其它业务BSC6900SET BSCFCPARA(Optional)AINTFFCE N A接口流控允许BSC6900SET BSCFCPARA(Optional)AINTFFC METHOD A接口流控方法BSC6900SET BSCFCPARA(Optional)AINTFFCR SRATE1A接口流控级别1限呼比例BSC6900SET BSCFCPARA(Optional)AINTFFCR SRATE2A接口流控级别2限呼比例BSC6900SET BSCFCPARA(Optional)AINTFFCR SRATE3A接口流控级别3限呼比例BSC6900SET BSCFCPARA(Optional)AINTFFCR SRATE4A接口流控级别4限呼比例BSC6900SET BSCFCPARA(Optional)AINTFFCR SRATE5A接口流控级别5限呼比例BSC6900SET BSCFCPARA(Optional)AINTFFCR SRATE6A接口流控级别6限呼比例BSC6900SET BSCFCPARA(Optional)AIPCSDSRVRDNDL EV CSD业务冗余级别BSC6900SET BSCBASIC(Optional)ALC_Fix_ Gain ALC固定增益值BSC6900SET TCPARA(Optional)Target_Le vel ALC固定电平值BSC6900SET TCPARA(Optional)ALC_Max_ Gain ALC最大增益值BSC6900SET TCPARA(Optional)ALC_Max_Target_Le vel ALC最高目标电平BSC6900SET TCPARA(Optional)ALC_Min_Target_Le vel ALC最低目标电平BSC6900SET TCPARA(Optional)ALC_Mode ALC电平控制模式BSC6900SET TCPARA(Optional)ALC_Switc h ALC功能开关BSC6900SET TCPARA(Optional)ALIVERET RY 存活重试次数BSC6900SET BSCNSPARA(Optional)ALIVETIM ER 存活定时器时长BSC6900SET BSCNSPARA(Optional)AllBw带宽BSC6900ADD RSCGRP(Mandatory)ALLOCDIF FTRX 允许跨载频重指配TBF BSC6900SET BSCPSSOFTPARA(Optional)ALLOCSINGLEPDCH FORSIGN ALLING 信令业务分配单信道开关BSC6900SET GCELLPSCHM(Optional)ALLOWAMRHALFR ATEUSER PERC 允许AMR半速率用户最大比例BSC6900SET GCELLCHMGBASIC(Optional)ADAMULT IPLEX 允许EDA复用BSC6900SET BSCPSSOFTPARA(Optional)ALLOWED MEASRPTMISSEDN UM 允许的测量报告丢失数BSC6900SET GCELLNC2PARA(Optional)ALLOWHA LFRATEU SERPERC 允许半速率用户最大比例BSC6900SET GCELLCHMGBASIC(Optional)ALLTSTYPE时隙类型BSC6900ADD AE1T1(Mandatory) ALLTSTYPE时隙类型BSC6900ADD PBE1T1(Optional)ALMD0支路0塔放电流告警门限下限BSC6900SET BTSDATUBP(Optional)ALMD1支路1塔放电流告警门限下限BSC6900SET BTSDATUBP(Optional)ALMD2支路2塔放电流告警门限下限BSC6900SET BTSDATUBP(Optional)ALMD3支路3塔放电流告警门限下限BSC6900SET BTSDATUBP(Optional)ALMD4支路4塔放电流告警门限下限BSC6900SET BTSDATUBP(Optional)ALMD5支路5塔放电流告警门限下限BSC6900SET BTSDATUBP(Optional)ALMDISA CDUR 告警恢复累计故障持续时间BSC6900ADD BTSALMMGMRULE(Mandatory)ALMENAB LE 告警使能标志BSC6900SET BTSAPMUBP(Optional)SET BTSDPMUBP(Optional)AlmId告警标识BSC6900SET BTSALMFLASHTHD(Mandatory) ALMID告警ID BSC6900ADD BTSALMMGMRULE(Mandatory)ALMLMTDOWN告警下限BSC6900SET BTSDGPSBP(Optional) ALMLMTUP1告警上限BSC6900SET BTSDGPSBP(Optional) ALMLMTUP2告警上限BSC6900SET BTSDGPSBP(Optional)ALMOCAC DUR 告警产生累计故障持续时间BSC6900ADD BTSALMMGMRULE(Mandatory)AlmOccurAccuTime HThd 故障产生累积时长门限BSC6900SET BTSALMFLASHTHD(Optional)AlmOccurAccuTime LThd 故障恢复累积时长门限BSC6900SET BTSALMFLASHTHD(Optional)AlmOccurTimesHTh d 故障产生累积次数门限BSC6900SET BTSALMFLASHTHD(Optional)AlmOccur TimesLThd 故障恢复累积次数门限BSC6900SET BTSALMFLASHTHD(Optional)ALMPARA CFGFLAG 告警参数配置允许BSC6900SET BTSDHEUBP(Optional)ALMTP告警类型BSC6900EXP ALMLOG(Optional) STA ALMLOG(Optional)ALPHA Alpha参数BSC6900SET GCELLPSPWPARA(Optional)ALTIDECI 天线高度小数部分BSC6900SET GCELLLCS(Optional)ALTITUDE GPS接收机天线高度BSC6900ADD GPS(Mandatory)ALTITUDE 天线高度整数部分BSC6900SET GCELLLCS(Optional)ALTITUDE IMP GPS接收机天线高度BSC6900ADD GPS(Mandatory)ALVL告警级别BSC6900EXP ALMLOG(Optional)ALVL告警级别BSC6900SET ALMLVL(Mandatory) SET ALMSCRN(Mandatory) SET ENVALMPARA(Optional)AMPC0支路0塔放馈电使能BSC6900SET BTSDATUBP(Optional)AMPC1支路1塔放馈电使能BSC6900SET BTSDATUBP(Optional)AMPC2支路2塔放馈电使能BSC6900SET BTSDATUBP(Optional)AMPC3支路3塔放馈电使能BSC6900SET BTSDATUBP(Optional)AMPC4支路4塔放馈电使能BSC6900SET BTSDATUBP(Optional)AMPC5支路5塔放馈电使能BSC6900SET BTSDATUBP(Optional)AMRBTSP WRNUM AMR基站功率控制级数BSC6900SET GCELLPWR2(Optional)AMRCALL PCALLOW ED III代功控AMR功控允许BSC6900SET GCELLPWR3(Optional)AMRDADT HAW AMR下行门限自适应调整允许BSC6900SET GCELLCCAMR(Optional)AMRDLLE VFTLEN AMR下行电平滤波器长度BSC6900SET GCELLPWR2(Optional)AMRDLPR EDLEND AMR下行预测测量报告个数BSC6900SET GCELLPWR2(Optional)AMRDLQH THRED AMR下行链路信号质量好门限BSC6900SET GCELLPWR2(Optional)AMRDLQL THRED AMR下行链路信号质量差门限BSC6900SET GCELLPWR2(Optional)AMRDLQU AFTLEN AMR下行质量滤波器长度BSC6900SET GCELLPWR2(Optional)AMRDLQU ALBADTRI G AMR下行质量差启动门限BSC6900SET GCELLPWR2(Optional)AMRDLQU ALBADUP LEV AMR下行质量差电平上门限偏移BSC6900SET GCELLPWR2(Optional)AMRDLSS HTHRED AMR下行链路信号强度上门限BSC6900SET GCELLPWR2(Optional)AMRDLSS LTHRED AMR下行链路信号强度下门限BSC6900SET GCELLPWR2(Optional)AMRFULL TOHALFH OALLOW AMR语音全半切换算法开关BSC6900SET GCELLHOBASIC(Optional)AMRFULL TOHALFH OATCBAD JSTEP AMR语音全半切换ATCB调整步长BSC6900SET GCELLHOBASIC(Optional)AMRFULLTOHALFH OATCBTH RESH AMR语音全半切换ATCB门限BSC6900SET GCELLHOBASIC(Optional)AMRFULL TOHALFH OPATHAD JSTEP AMR语音全半切换路径损耗调整步长BSC6900SET GCELLHOBASIC(Optional)AMRFULLTOHALFH OPATHTH RESH AMR语音全半切换路径损耗门限BSC6900SET GCELLHOBASIC(Optional)AMRFULLTOHALFH OQUALTH RESH AMR全半切换质量门限BSC6900SET GCELLHOBASIC(Optional)AMRFULL TOHALFH OTHRESH AMR语音全半切换负荷门限BSC6900SET GCELLHOBASIC(Optional)AMRHALFTOFULLH OATCBTH RESH AMR语音半全切换ATCB门限BSC6900SET GCELLHOBASIC(Optional)AMRHALFTOFULLH OPATHTH RESH AMR语音半全切换路径损耗门限BSC6900SET GCELLHOBASIC(Optional)AMRHALF TOFULLH OQUALAL LOW 质量触发AMR语音半全切换算法开关BSC6900SET GCELLHOBASIC(Optional)AMRHALFTOFULLH OQUALTH RESH AMR语音半全切换质量门限BSC6900SET GCELLHOBASIC(Optional)AMRHALF TOFULLH OTHRESH AMR语音半全切换负荷门限BSC6900SET GCELLHOBASIC(Optional)AMRMAX ADJPCVA L AMR按质量向上功控最大允许调整步长BSC6900SET GCELLPWR2(Optional)AMRMAX STEP0AMR质量带0按电平向下功控最大步长BSC6900SET GCELLPWR2(Optional)AMRMAX STEP1AMR质量带1按电平向下功控最大步长BSC6900SET GCELLPWR2(Optional)AMRMAX STEP2AMR质量带2按电平向下功控最大步长BSC6900SET GCELLPWR2(Optional)AMRMAX VALADJR X AMR按电平向上功控最大允许调整步长BSC6900SET GCELLPWR2(Optional)AMRMRC OMPREG AMR测量报告补偿开关BSC6900SET GCELLPWR2(Optional)AMRPCAD JPERIOD AMR功率控制调整周期BSC6900SET GCELLPWR2(Optional)AMRQUAL STEP AMR按质量向下功控最大步长BSC6900SET GCELLPWR2(Optional)AMRSADL UPGRADE AMRSACCH下行功率提升等级BSC6900SET GCELLPWRBASIC(Optional)AMRTCHH PRIORALL OW AMR呼叫优先分配半速率开关BSC6900SET GCELLCHMGAD(Optional)AMRTCHH PRIORLO AD AMR呼叫优先分配半速率小区负荷门限BSC6900SET GCELLCHMGAD(Optional)AMRUADT HAW AMR上行门限自适应调整允许BSC6900SET GCELLCCAMR(Optional)AMRULLE VFTLEN AMR上行电平滤波器长度BSC6900SET GCELLPWR2(Optional)AMRULPR EDLEND AMR上行预测测量报告个数BSC6900SET GCELLPWR2(Optional)AMRULQH THRED AMR上行链路信号质量好门限BSC6900SET GCELLPWR2(Optional)AMRULQL OWTHRE D AMR上行链路信号质量差门限BSC6900SET GCELLPWR2(Optional)AMRULQU AFTLEN AMR上行质量滤波器长度BSC6900SET GCELLPWR2(Optional)AMRULQU ALBADTRI G AMR上行质量差启动门限BSC6900SET GCELLPWR2(Optional)AMRULQU ALBADUP LEV AMR上行质量差电平上门限偏移BSC6900SET GCELLPWR2(Optional)AMRULSS HTHRED AMR上行链路信号强度上门限BSC6900SET GCELLPWR2(Optional)AMRULSS LTHRED AMR上行链路信号强度下门限BSC6900SET GCELLPWR2(Optional)AN19A接口复位电路消息最大重发次数BSC6900SET OTHSOFTPARA(Optional)AN4A接口BSC复位消息最大重发次数BSC6900SET AITFOTHPARA(Optional)ANC_Max _Gain ANC噪声补偿最大增益BSC6900SET TCPARA(Optional)ANC_Swit ch ANC功能开关BSC6900SET TCPARA(Optional)ANC_Targ et_SNR ANC远近端目标信噪比BSC6900SET TCPARA(Optional)ANGLE 电调天线倾角BSC6900SET BTSANTANGLE(Mandatory)ANI邻节点标识BSC6900ADD ADJNODE(Mandatory) ADD IPPATH(Mandatory) ADD ADJMAP(Mandatory)ANI邻节点标识BSC6900ADD IPMUX(Mandatory)ADD IPPATHBIND(Mandatory)ANM告警名称BSC6900SET ENVALMPARA(Optional)ANR_Mod e ANR噪声抑制算法模式BSC6900SET TCPARA(Optional)ANR_Nois e_Reducti on_Level ANR最小信道增益变量BSC6900SET TCPARA(Optional)ANR_Noise_Target_ Level ANR目标噪声电平BSC6900SET TCPARA(Optional)ANR_Swit ch ANR功能开关BSC6900SET TCPARA(Optional)ANTAANGLE天线方位角BSC6900SET GCELLLCS(Optional)ANTENNA LONG GPS馈缆时延BSC6900SET BTSDGPSBP(Optional)SET BTSUSCUBP(Optional)ANTENNAPOWERS WITCH 天馈供电开关BSC6900SET BTSDGPSBP(Optional)SET BTSUSCUBP(Optional)ANTIERRF LAG E1T1端口抗误码率使能开关BSC6900ADD MPGRP(Optional)AntiTheftAl low 允许防盗告警自动清除BSC6900SET BTSTHEFTALM(Optional)ANTNO天线编号BSC6900LOD RETANTCFG(Mandatory) SET BTSANTANGLE(Mandatory) SET RETANTENB(Mandatory)ANTPASSNO天馈通道号BSC6900ADD TRXBIND2PHYBRD(Mandatory)ANTPASS NO 从位置组天馈通道号BSC6900ADD BTSBINDLOCGRP(Optional)AORB 下行支路天馈通道号BSC6900ADD BTSANTFEEDERBRD(Mandatory)SETBTSANTFEEDERCONNECT(Optional)APN A端口号BSC6900ADD MTP3LNK(Mandatory) APP应用类型BSC6900ADD SCTPLNK(Mandatory)APPTYPE 半永久应用类型BSC6900ADD SEMILINK(Mandatory)AqmM AQM N值更新频率包间隔BSC6900SET BSCPSSOFTPARA(Optional)AqmMaxT h AQM最大门限BSC6900SET BSCPSSOFTPARA(Optional)AqmMinTh AQM拥塞门限BSC6900SET BSCPSSOFTPARA(Optional)AqmNinit AQM丢包间隔初始值BSC6900SET BSCPSSOFTPARA(Optional)AqmNLow erBound AQM丢包间隔下门限BSC6900SET BSCPSSOFTPARA(Optional)AqmNUpB ound AQM丢包间隔上门限BSC6900SET BSCPSSOFTPARA(Optional)AqmSwitch AQM算法开关BSC6900SET BSCPSSOFTPARA(Optional)AqmTarTh AQM目标门限BSC6900SET BSCPSSOFTPARA(Optional)AreaCode位置码BSC6900SET BSCBASIC(Optional)AREAFLAG主备区标志BSC6900CMP BRDAREA(Optional) LOD PATCH(Optional)AREAFLAG主备区标志BSC6900LOD BRD(Optional)SYN BRDAREA(Optional)AREDIST HD 异常释放消失门限BSC6900SET GTRXRLALM(Optional)ARELBAS E 异常释放统计基数BSC6900SET GTRXRLALM(Optional)ARELWTH D 异常释放告警门限BSC6900SET GTRXRLALM(Optional)ARPRETR Y ARP超时重发次数BSC6900STR IPCHK(Optional)ARPTIME OUT ARP报文超时时间[100ms]BSC6900STR IPCHK(Optional)ASN A端口槽位号BSC6900ADD MTP3LNK(Mandatory)ASN A接口槽位号BSC6900ADD ATERSL(Optional)ADD ATERCONSL(Optional)ASRN A端口插框号BSC6900ADD MTP3LNK(Mandatory)ASS 告警网管分类BSC6900EXP ALMLOG(Optional)STA ALMLOG(Optional)ASS 告警网管分类BSC6900SET ENVALMPARA(Optional)AssignBett erCellEn 指配优选更好小区允许BSC6900SET GCELLHOAD(Optional)ASSLOAD JUDGEEN 指配时小区负荷判断允许BSC6900SET GCELLCCBASIC(Optional)ASSOLRXLEVOFFS ET 指配内圆电平条件偏移BSC6900SET GCELLCHMGAD(Optional)ASSORXU CN 关联RXU单板机柜号BSC6900SET BTSAPMUBP(Optional)SET BTSDEMUBP(Optional)SET BTSDHEUBP(Optional)ASSORXU CN 关联RXU单板机柜号BSC6900SET BTSRXUBP(Mandatory)ASSORXU SN 关联RXU单板槽位号BSC6900SET BTSAPMUBP(Optional)SET BTSDEMUBP(Optional)SET BTSDHEUBP(Optional)ASSORXU SN 关联RXU单板槽位号BSC6900SET BTSRXUBP(Mandatory)ASSORXU SRN 关联RXU单板插框号BSC6900SET BTSAPMUBP(Optional)SET BTSDEMUBP(Optional)SET BTSDHEUBP(Optional)ASSORXU SRN 关联RXU单板插框号BSC6900SET BTSRXUBP(Mandatory)ASSThres 绝对电平门限BSC6900SET OTHSOFTPARA(Optional)ASSTIMER T3107BSC6900SET GCELLTMR(Optional)AT1T1BSC6900SET BSCTMR(Optional)AT13T13_秒BSC6900SET BSCAITFTMR(Optional) AT17T17_秒BSC6900SET BSCAITFTMR(Optional) AT18T18_秒BSC6900SET BSCAITFTMR(Optional) AT19T19BSC6900SET BSCTMR(Optional)AT20T20BSC6900SET BSCTMR(Optional)AT4T4_秒BSC6900SET BSCAITFTMR(Optional)ATCBHOE N 同心圆ATCB切换算法开关BSC6900SET GCELLHOBASIC(Optional)ATCBHYS T 内圆边界到外圆边界的距离磁滞BSC6900SET GCELLHOEDBPARA(Optional)ATCBTHR ED 内圆边界到外圆边界的距离BSC6900SET GCELLHOEDBPARA(Optional)Ater8KSw Ater资源8K的功能开关BSC6900SET OTHSOFTPARA(Optional)AterCongH RFlag Ater资源拥塞触发HR分配功能开关BSC6900SET OTHSOFTPARA(Optional)AterCongst Ratio Ater资源拥塞百分比BSC6900SET OTHSOFTPARA(Optional)ATERIDX Ater 连接通道索引号BSC6900ADD MTP3LNK(Mandatory)ADD ATERE1T1(Mandatory)ADD ATERCONPATH(Optional)ADD ATERSL(Mandatory)ADD ATERCONSL(Mandatory)ADD SEMILINK(Mandatory)AterJamTh reshold2St artLs 启动BSC本地交换的Ater口拥塞门限BSC6900SET BSSLS(Optional)ATERMAS K Ater口时隙掩码BSC6900ADD MTP3LNK(Mandatory)ADD ATERSL(Mandatory)ADD ATERCONSL(Mandatory)ATEROML FLAG 是否配置OML链路BSC6900ADD SEMILINK(Mandatory)ATEROML INX Ater维护链路索引号BSC6900ADD ATEROML(Mandatory)ATERPIDX Ater连接通道索引号BSC6900ADD ATEROML(Mandatory)ATERSLID Ater信令链路编码BSC6900ADD ATERSL(Optional)ADD ATERCONSL(Optional)ATERTRA NSMODE Ater接口传输模式BSC6900SET BSCBASIC(Mandatory)ATN天馈支路号BSC6900STR BTSVSWRTST(Optional)ATSMASK A接口时隙掩码BSC6900ADD MTP3LNK(Mandatory)ATT 附着分离允许BSC6900SET GCELLIDLEBASIC(Optional)ATTENFA CTOR1天馈支路1塔放衰减因子BSC6900SET BTSRXUBP(Optional)ATTENFA CTOR2天馈支路2塔放衰减因子BSC6900SET BTSRXUBP(Optional)AUSTOP 环回时长[分钟]BSC6900SET E1T1LOP(Optional)AUSTOP 测试时长[分钟]BSC6900STR E1T1TST(Optional)AUTHMODE认证模式BSC6900SET SSLAUTHMODE(Mandatory) AUTHMODE验证模式BSC6900ADD PPPLNK(Mandatory) AUTHMODE验证模式BSC6900ADD MPGRP(Mandatory)AUTHMODE验证模式BSC6900ADD BTSPPPLNK(Mandatory) ADD BTSMPGRP(Mandatory) IMP BTSPPPLNK(Mandatory) IMP BTSMPGRP(Mandatory)AUTHNAME验证用户名BSC6900ADD PPPLNK(Mandatory) AUTHNAME验证用户名BSC6900ADD MPGRP(Mandatory)AUTHNAME验证用户名BSC6900ADD BTSPPPLNK(Mandatory) ADD BTSMPGRP(Mandatory) IMP BTSPPPLNK(Mandatory) IMP BTSMPGRP(Mandatory)AUTHPWD验证密码BSC6900ADD PPPLNK(Mandatory) AUTHPWD验证密码BSC6900ADD MPGRP(Mandatory)AUTHPWD验证密码BSC6900ADD BTSPPPLNK(Mandatory) ADD BTSMPGRP(Mandatory) IMP BTSPPPLNK(Mandatory) IMP BTSMPGRP(Mandatory)AUTHTYP E 验证协议类型BSC6900ADD PPPLNK(Optional)AUTHTYP E 验证协议类型BSC6900ADD MPGRP(Optional)AUTHTYP E 验证协议类型BSC6900ADD BTSPPPLNK(Optional)ADD BTSMPGRP(Optional)IMP BTSPPPLNK(Optional)IMP BTSMPGRP(Optional)AUTO是否自协商BSC6900SET ETHPORT(Optional)AUTOADD SRCON 是否自动增加框间互连BSC6900ADD BRD(Optional)AUTOADJ ULTHHYS TF 自动调整上行门限和磁滞[全速率]BSC6900SET GCELLCCAMR(Optional)AUTOADJ ULTHHYS TH 自动调整上行门限和磁滞[半速率]BSC6900SET GCELLCCAMR(Optional)AutoGetBt sLogFlag 是否允许基站日志自动提取BSC6900SET OTHSOFTPARA(Optional)AUTONEG自协商模式BSC6900SET BTSETHPORT(Optional)AUTOTYP E 自动加载激活工作模式BSC6900SET BTSAUTODLDACTINFO(Optional)AUTOULK SW 自动解锁开关BSC6900LCK SCHTSK(Optional)AutoUnloc kTime 自动解锁时间BSC6900SET PWDPOLICY(Optional)AUTYPE 管理单元类型BSC6900SET OPT(Optional)AVer A接口阶段标识BSC6900SET BSCBASIC(Optional)AVOL告警电平BSC6900SET ALMPORT(Optional)AVOL告警电平BSC6900SET BTSENVALMPORT(Optional)B1B2SDT HRD B1B2信号劣化门限值BSC6900SET OPT(Optional)B1B2SFT HRD B1B2信号失效门限值BSC6900SET OPT(Optional)B3SDTHR D B3信号劣化门限值BSC6900SET OPT(Optional)B3SFTHR D B3信号失效门限值BSC6900SET OPT(Optional)BACK8KC LKSW1背板LINE1输出开关BSC6900SET CLK(Optional)BACK8KC LKSW2背板LINE2输出开关BSC6900SET CLK(Optional)BackupPath备份目录BSC6900BKP LOGDB(Optional)BACKUPP ATH 备份文件保存路径BSC6900BKP DB(Optional)BADQUALDISCTHR ES 质量差挂机统计门限BSC6900SET GCELLSOFT(Optional)bAdvEstDl Tbf 下行TBF提前建立BSC6900SET BSCPSSOFTPARA(Optional)BAKDEVT AB 基站接口板条码2BSC6900ADD BTSESN(Optional)BAKIP 备端口IP地址BSC6900STR IPCHK(Optional)BAKMASK备端口掩码BSC6900STR IPCHK(Optional)BAKPWRSAVMETH OD 备电节电方法BSC6900SET BTSBAKPWR(Mandatory)BAKPWRSAVPOLIC Y 备电节电策略BSC6900SET BTSBAKPWR(Optional)BANDINDI CATOR19 001900小区高频段1900支持指示BSC6900SET GCELLSOFT(Optional)BANDINDI CATOR85 0850小区高频段1900支持指示BSC6900SET GCELLSOFT(Optional)BANDINDI CATOR90 0900小区高频段1900支持指示BSC6900SET GCELLSOFT(Optional)BANTIME 连续发生最大次数后禁止时间BSC6900SET GCELLHOAD(Optional)BARCODL ST 机柜条码列表BSC6900SET BTSRACKBC(Mandatory)BASEBTSI D 基准基站索引号BSC6900ADD AISSCFG(Mandatory)BASETEM PERATUR E 电池组温度补偿依据的温度BSC6900SET BTSAPMUBP(Optional)BASETEM PERATUR E 电池组温度补偿依据的温度BSC6900SET BTSDPMUBP(Optional)BATTCAP ACITY 蓄电池柜容量BSC6900SET BTSDPMUBP(Optional)BATTENA BLEDIN 蓄电池柜配置允许BSC6900SET BTSDPMUBP(Optional)BATTERYDISCHAR GEDEPTH 蓄电池放电深度BSC6900SET BTSAPMUBP(Optional)SET BTSDPMUBP(Optional)BATTTYP E 蓄电池柜类型BSC6900SET BTSDPMUBP(Optional)BBAPSRV PN BBAP服务侦听端口号BSC6900SET SCTPSRVPORT(Optional)BBDIF 上下行平衡基本偏差BSC6900SET GTRXRLALM(Optional)BC蓄电池容量BSC6900SET BTSAPMUBP(Optional)BCC 小区基站色码BSC6900ADD GCELL(Optional)BCC 小区基站色码BSC6900ADD GEXT2GCELL(Mandatory)BCC基站色码BSC6900ADD GCELLQUICKSETUP(Optional)BCCH 小区的BCCH频点BSC6900ADD GEXT2GCELL(Mandatory)BCCHFRE Q 主B载频频点BSC6900ADD GCELLQUICKSETUP(Mandatory)BCCHTRX HP 主B载频的跳频类型BSC6900SETGCELLHOPQUICKSETUP(Mandatory)BCCONGESTALMB OUND BC拥塞告警门限BSC6900SET BSCPSSOFTPARA(Optional)BCCONGESTRESA LMBOUND BC拥塞告警恢复门限BSC6900SET BSCPSSOFTPARA(Optional)BCDSCP BG[QoS]对应的DSCP BSC6900SET BSCPSTCDSCPMAP(Optional)BCID 承载信道标识BSC6900STR FRPORTLOOP(Mandatory)BLK BC(Mandatory)ADD BC(Mandatory)ADD NSVC(Mandatory)BCLC 充电限流点系数BSC6900SET BTSAPMUBP(Optional)BCV均充电压BSC6900SET BTSAPMUBP(Optional)BE 蓄电池柜配置允许BSC6900SET BTSAPMUBP(Optional)BEARP1P RIWEIGH T BE业务ARP1优先级BSC6900SET GCELLPSCHM(Optional)BEARP2P RIWEIGH T BE业务ARP2优先级BSC6900SET GCELLPSCHM(Optional)BEARP3P RIWEIGH T BE业务ARP3优先级BSC6900SET GCELLPSCHM(Optional)BEARTYP E 目的信令点承载类型BSC6900ADD N7DPC(Mandatory)BEATSEN DINGDIS 心跳发送间隔BSC6900SET GBSCREDGRP(Optional)BEPPERIOD BEP周期BSC6900SET GCELLEGPRSPARA(Optional)BESTTDD CELLNUM 最好小区列表TDD小区数BSC6900SET GCELLCCUTRANSYS(Optional)BET3GHO EN 3G更好小区切换算法允许BSC6900SET GCELLHOUTRANFDD(Optional)SET GCELLHOUTRANTDD(Optional)BETTERC ELLHOEN 更好小区切换算法允许BSC6900SET GCELLHOBASIC(Optional)BETTERCELLLASTT IME 更好小区切换持续时间BSC6900ADD G2GNCELL(Optional)BETTERCELLSTATT IME 更好小区切换统计时间BSC6900ADD G2GNCELL(Optional)BFDDETE CTCOUNT BFD检测包超时次数BSC6900STR IPCHK(Optional)BFDSN BFD会话ID BSC6900ADD BTSBFD(Mandatory)ADD BTSIPRTBIND(Mandatory)BFRANGE 上下行平衡波动范围BSC6900SET GTRXRLALM(Optional)BHPREPO LICY 基带跳频互助倒回策略BSC6900SET GCELLCCACCESS(Optional)BITOFFSE T 帧内bit偏移[1/8bit]BSC6900SET BTSEXCURSION(Mandatory)SET BSCSYNCOFF(Mandatory)BKGARP1 PRIWEIG HT 背景业务ARP1优先级权重BSC6900SET GCELLPSCHM(Optional)BKGARP2 PRIWEIG HT 背景业务ARP2优先级权重BSC6900SET GCELLPSCHM(Optional)BKGARP3 PRIWEIG HT 背景业务ARP3优先级权重BSC6900SET GCELLPSCHM(Optional)BLKFILTE RSW 告警闪断过滤开关BSC6900SET ALMBLKSW(Optional)BLKPRD 告警闪断门限BSC6900SET ALMBLKPARA(Optional)BLKSTAT PRD 闪断统计告警观察时间窗BSC6900SET ALMBLKSW(Optional)BLKSTAT SW 告警闪断统计开关BSC6900SET ALMBLKSW(Optional)BLOCKRE TRY 闭塞重试次数BSC6900SET BSCNSPARA(Optional)BLOCKTI MER 闭塞定时器时长BSC6900SET BSCNSPARA(Optional)BMPN BM框端口号BSC6900ADD ATERCONPATH(Mandatory)BMSN BM框槽位号BSC6900ADD ATERCONPATH(Mandatory)BMSRN BM框插框号BSC6900ADD ATERCONPATH(Mandatory)BMTCFCT imerLen TC框与BM框之间流控定时器长度BSC6900SET BSCTMR(Optional)BORROW DEVIP 是否借用设备地址BSC6900ADD PPPLNK(Mandatory)ADD MPGRP(Mandatory)BOXFLG 上报告警箱标志BSC6900SET BOXRPT(Mandatory)BP1RXU链的断点位置1BSC6900SET BTSBREAKPOINT(Optional)BP2RXU链的断点位置2BSC6900SET BTSBREAKPOINT(Optional)BQHOEN BQ切换算法允许BSC6900SET GCELLHOBASIC(Optional)BQLASTTI ME BQ切换邻区持续时间BSC6900ADD G2GNCELL(Optional)BQMARGI N 质量差切换带BSC6900ADD G2GNCELL(Optional)BQSTATTI ME BQ切换邻区统计时间BSC6900ADD G2GNCELL(Optional)BRDCLASS单板种类BSC6900STR BKP(Mandatory)BRDCLASS单板种类BSC6900SET FCSW(Mandatory)SET FCCPUTHD(Mandatory) SET FCMSGQTHD(Mandatory)BRDCLASS单板种类BSC6900SET CPUTHD(Mandatory) BRDCLASS单板种类BSC6900ADD BRD(Mandatory) BRDNO单板号BSC6900STR BTSLOG(Mandatory) BRDNO单板号BSC6900STR BTSVSWRTST(Optional)BRDRXBW接收带宽BSC6900ADD BTSBRDCAP(Mandatory) ADD BTSRXUBRD(Optional)BRDSWT YPE 基站单板软件类型BSC6900LOD BTSSW(Mandatory)BRDTXBW发送带宽BSC6900ADD BTSBRDCAP(Mandatory) ADD BTSRXUBRD(Optional)BRDTYPE单板类型BSC6900SET DPUBRDTYPE(Mandatory)BRDTYPE单板类型BSC6900ADD BRD(Optional) BRDTYPE单板类型BSC6900SET ETHPORT(Mandatory) BRDTYPE单板类型BSC6900ADD PPPLNK(Mandatory)BRDTYPE单板类型BSC6900ADD MPGRP(Mandatory) BRDTYPE单板类型BSC6900ADD MPLNK(Mandatory) BrdType单板类型BSC6900ADD BTSBRDCAP(Mandatory)BRDTYPE单板类型BSC6900STR BTSLOG(Mandatory)BREAKTI ME II代环网倒换前等待时间BSC6900SET BTSRINGATTR(Optional)BROADCASTCONTENT广播内容BSC6900SET GCELLSBC(Optional) BROADCASTINTERVAL广播间隔BSC6900SET GCELLSBC(Optional) BS备份方式BSC6900BKP LOGDB(Optional)BSAGBLK SRES 接入允许保留块数BSC6900SET GCELLIDLEBASIC(Optional)BSCDPC 外部BSC目的信令点编码BSC6900ADD EXTBSC(Mandatory)BSCDynS witchTrxP AAllow BSC动态关载频功能允许BSC6900SET BSCDSTPA(Optional)BSCFLAG BSC标志BSC6900BLK ACIC(Mandatory) ADD AE1T1(Mandatory)BSCGATEWAYIP BSC 网关BSC6900ADD GCBSADDR(Mandatory)BSCGATH ET BSC间偏移信息搜集终止时间BSC6900ADD AISSCFG(Optional)BSCGATH ST BSC间偏移信息搜集起始时间BSC6900ADD AISSCFG(Optional)BSCID BSC ID BSC6900ADD ADJNODE(Mandatory)BSCIDX BSC索引BSC6900ADD GEXT2GCELL(Optional) ADD EXTBSC(Mandatory)BSCINCH PRD BSC间微调周期BSC6900ADD AISSCFG(Optional)BSCIP BSC IP地址BSC6900ADD GCBSADDR(Mandatory)BSCIP BSC IP BSC6900ADD BTSAUTOPLAN(Mandatory) SET BTSIP(Optional)IMP BTSIPPARA(Mandatory)BscLsStart Mode BSC本地交换启动条件BSC6900SET BSSLS(Optional)BSCNAME 外部BSC名称BSC6900ADD EXTBSC(Mandatory)BSCPMA允许抢占BSC6900SET OTHSOFTPARA(Optional)BSCPMAI RAHO BSC内切换允许抢占BSC6900SET OTHSOFTPARA(Optional)BSCPN 入BSC端口号BSC6900ADD BTSMONITORTS(Mandatory)BSCPORT BSC 端口号BSC6900ADD GCBSADDR(Mandatory)BSCPRICL ASS eMLPP等级按多级处理BSC6900SET OTHSOFTPARA(Optional)BSCQAD允许排队BSC6900SET OTHSOFTPARA(Optional)BSCQADI RAHO BSC内切换允许排队BSC6900SET OTHSOFTPARA(Optional)BSCRESERVEDPARA1保留参数1BSC6900SET OTHSOFTPARA(Optional) BSCRESERVEDPAR A10保留参数10BSC6900SET OTHSOFTPARA(Optional)BSCRESERVEDPAR A11保留参数11BSC6900SET OTHSOFTPARA(Optional)BSCRESERVEDPAR A12保留参数12BSC6900SET OTHSOFTPARA(Optional)BSCRESERVEDPAR A13保留参数13BSC6900SET OTHSOFTPARA(Optional)BSCRESERVEDPAR A14保留参数14BSC6900SET OTHSOFTPARA(Optional)BSCRESERVEDPAR A15保留参数15BSC6900SET OTHSOFTPARA(Optional)BSCRESERVEDPAR A16保留参数16BSC6900SET OTHSOFTPARA(Optional)BSCRESERVEDPAR A17保留参数17BSC6900SET OTHSOFTPARA(Optional)BSCRESERVEDPAR A18保留参数18BSC6900SET OTHSOFTPARA(Optional)。

实验报告
课程名称：第三代移动通信项目名称：GSM实验
姓名：专业：通信工程班级：学号：同组成员：
1注：1、实验预习部分包括实验环境准备和实验所需知识点准备。

2、若是单人单组实验，同组成员填无。

2注：实验过程记录要包含实验目的、实验原理、实验步骤，页码不够可自行添加。

点击MML命令图标，出现输入命令界面；
（2）在命令输入位置可以执行相关的命令；将每一条命令输入，点击执行命令将生效；
顺序将以上全局数据所有命令执行完成，设备将重新启动；等待3分钟设备重启动完成；
点击页面顶部的设备维护标签可以看到设备板位状态;
）实验心得体会：
实验报告成绩（百分制）__________ 实验指导教师签字：__________。