英文工厂专业用语(V01)

[工厂专业词汇大全] 出处:鸿海精密大陆龙华厂组装、冲压、喷漆等专业词汇Assembly line 组装线Layout 布置图Conveyer 流水线物料板Rivet table 拉钉机Rivet gun 拉钉枪Screw driver 起子Electric screw driver 电动起子Pneumatic screw driver 气动起子worktable 工作桌OOBA 开箱检查fit together 组装在一起fasten 锁紧(螺丝) fixture 夹具(治具) pallet 栈板barcode 条形码barcode scanner 条形码扫描仪fuse together 熔合fuse machine 热熔机repair 修理operator 作业员QC 品管supervisor 课长ME 制造工程师MT 制造生技cosmetic inspect 外观检查inner parts inspect 内部检查thumb screw 大头螺丝lbs.inch 镑、英寸EMI gasket 导电条front plate 前板rear plate 后板chassis |'∫asi| 基座bezel panel 面板power button 电源按键reset button 重置键Hi-pot test of SPS 高源高压测试V oltage switch of SPS 电源电压接柆键sheet metal parts 冲件plastic parts 塑料件SOP 制造作业程序material check list 物料检查表work cell 工作间trolley 台车carton 纸箱sub-line 支线left fork 叉车personnel resource department人力资源部production department 生产部门planning department 企划部QC Section 品管科stamping factory 冲压厂painting factory 烤漆厂molding factory 成型厂common equipment 常用设备punching machine 冲床robot 机械手hydraulic machine 油压机lathe 车床planer |'plein | 刨床miller 铣床grinder 磨床driller 钻床linear cutting 线切割electrical sparkle 电火花welder 电焊机staker=reviting machine 铆合机position 职务president 董事长general manager 总经理special assistant manager 特助factory director 厂长department director 部长deputy manager |'depjuti| =vice manager 副理section supervisor 课长deputy section supervisor =vice section supervisor副课长group leader/supervisor 组长line supervisor 线长assistant manager 助理to move, to carry, to handle 搬运be put in storage 入库pack packing 包装to apply oil 擦油to file burr 锉毛刺final inspection 终检to connect material 接料to reverse material 翻料wet station 沾湿台Tiana 天那水cleaning cloth 抹布to load material 上料to unload material 卸料to return material/stock to 退料scraped |'skrapid| 报废scrape ..v. 刮;削deficient purchase 来料不良manufacture procedure 制程deficient manufacturing procedure制程不良oxidation |' ksi'dei n| 氧化scratch 刮伤dents 压痕defective upsiding down 抽芽不良defective to staking 铆合不良embeded lump|in'bed| |l mp| 镶块feeding is not in place 送料不到位stamping-missing 漏冲production capacity 生产力education and training 教育与训练proposal improvement 提案改善spare parts=buffer 备件forklift 叉车trailer=long vehicle 拖板车compound die 模die locker 锁模器pressure plate=plate pinch 压板bolt 螺栓name of a department 部门名称administration/general affairs dept总务部automatic screwdriver 电动启子thickness gauge 厚薄规gauge(or jig) 治具power wire 电源线buzzle 蜂鸣器defective product label 不良标签identifying sheet list 标示单screwdriver holder 起子插座pedal 踩踏板stopper 阻挡器flow board 流水板hydraulic handjack 油压板车forklift 叉车pallet 栈板, (装卸、搬运货物用的)托盘,货板,集装架glove(s) 手套glove(s) with exposed fingers 割手套thumb 大拇指forefinger 食指midfinger 中指ring finger 无名指little finger 小指band-aid 创可贴industrial alcohol 工业酒精alcohol container 沾湿台head of screwdriver 起子头sweeper 扫把mop 拖把vacuum cleaner 吸尘器rag 抹布garbage container 灰箕garbage can 垃圾箱garbage bag 垃圾袋chain 链条jack 升降机production line 流水线chain 链条槽magnetizer 加磁器lamp holder 灯架to mop the floor 拖地to clean the floor 扫地to clean a table 擦桌子air pipe 气管packaging tool 打包机packaging 打包missing part 漏件wrong part 错件excessive defects 过多的缺陷critical defect 极严重缺陷major defect 主要缺陷minor defect 要缺陷not up to standard 不合规格dimension/size is a little bigger尺寸偏大(小)cosmetic defect外观不良,装饰性的;表面的slipped screwhead/slippery screw head 螺丝滑头slipped screwhead/shippery screw thread 滑手speckle 斑点mildewed=moldy=mouldy 发霉rust 生锈deformation 变形burr(金属)flash(塑件)毛边poor staking 铆合不良excessive gap 间隙过大grease/oil stains 油污inclusion 杂质painting peel off 脏污shrinking/shrinkage 缩水mixed color 杂色scratch 划伤poor processing 制程不良poor incoming part 事件不良fold of pakaging belt 打包带折皱painting make-up 补漆discoloration 羿色water spots 水渍polishing/surface processing 表面处理exposed metal/bare metal 金属裸露lack of painting 烤漆不到位safety 安全quality 品质delivery deadline 交货期cost 成本engineering 工程die repair 模修enterprise plan = enterprise expansion projects企划QC 品管die worker 模工production, to produce 生产equipment设备to start a press开机stop/switch off a press关机classification整理regulation整顿cleanness清扫conservation清洁culture教养qualified products, up-to-grade products 良品defective products, not up-to-grade products不良品waste废料board广告牌feeder送料机sliding rack滑料架上午10:36 2005/6/2die change 换模to fix a die装模to take apart a die拆模to repair a die修模packing material包材basket蝴蝶竺plastic basket胶筐isolating plate baffle plate; barricade隔板carton box纸箱to pull and stretch拉深to put material in place, to cut material, to input落料to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料transportation运输(be)qualified, up to grade合格not up to grade, not qualified不合格material change, stock change材料变更feature change 特性变更evaluation评估prepare for, make preparations for 准备parameters参数rotating speed, revolution转速manufacture management制造管理abnormal handling异常处理production unit生产单位lots of production生产批量steel plate钢板roll material卷料manufacture procedure制程operation procedure作业流程to revise, modify修订to switch over to, switch---tothrow--over switching over切换engineering, project difficulty工程瓶颈stage die工程模automation自动化to stake, staking, reviting铆合add lubricating oil加润滑油shut die架模shut height of a die架模高度analog-mode device类模器die lifter举模器argon welding氩焊vocabulary for stamping 冲压常词汇stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸robot机械手taker取料机conveyer belt输送带transmission rack输送架top stop上死点bottom stop下死点one stroke一行程inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, block stop 定位块reset复位smoothly顺利dent压痕scratch刮伤deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取approval examine and verify审核processing, to process加工delivery, to deliver 交货to return delivery to. to send delivery back to return of goods退货registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收to notice通知application form for purchase请购单consume, consumption消耗to fill in填写abrasion磨损reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking (be)broken,(be)cracked 断裂to lubricate润滑common vocabulary for die engineering 模具工程常用词汇die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die连续模compound die复合模punched hole冲孔panel board镶块to cut edges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line stretching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder活页夹file folder文件夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备waste materials废料work in progress product在制品casing = containerazation装箱quantity of physical invetory second count 复盘点数量quantity of customs count 会计师盘点数量blank and waste sheet NO. 空白与作废单号the first page 第一联bill name单据名称filed by accounting department for reference 会计部存查end-user/using unit(department) 使用单位summary of year-end physical inventory bills 年终盘点截止单据汇总表This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department)本表请与盘点清册一起送会计部－(NHK厂区送财会部)Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－状况明细表plate电镀mold成型material for engineering mold testing工程试模材料not included in physical inventory不列入盘点incoming material to be inspected进货待验sample样品description品名steel/rolled steel钢材material statistics sheet物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位location地点chairman主席present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by 核准/审核/承办PCE assembly production schedule sheetPCE组装厂生产排配表model机钟work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet年终盘点差异分析表physical inventory盘点数量physical count quantity账面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion draw展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条形码flow chart流程窗体assembly组装stamping冲压molding成型spare parts=buffer备品coordinate坐标dismantle the die折模auxiliary function辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave 凹convex 凸short射料不足nick缺口speck瑕疪shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴angular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸)draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension draw展开图procedure draw工程图die structure draw模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板)stripping plate内外打(脱料板)outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing block衬套cover plate盖板guide pad导料块塑件&模具相关英文compression molding压缩成型flash mold溢流式模具compress mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具移转成型用模具encapsulation molding低压封装成型射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道h=0.02~0.05mmw=3.2mmL=3~5mmwelding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆) slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口质量人员名称类fan gate扇形浇口dish gate因盘形浇口H=F=1/2t~1/5tT=2.5~3.5mm diaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Φ0.8~1.0mmRunner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣IQC incoming quality control 进料质量管理人员TQC total quality control 全面质量管理PQC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance 出货质量保证人员QE quality engineering 质量工程人员质量保证类FAI first article inspection 新品首件检查FAA first article assurance 首件确认TVR tool verification report 模具确认报告3B 3B 模具正式投产前确认CP capability index 能力指数CPK capability index of process 模具制程能力参数SSQA standardized supplier quality 合格供货商质量评估OOBA out of box audit 开箱检查QFD quality function deployment 质量机能展开FMEA failure model effectiveness analysis 失效模式分析FA final audit 最后一次稽核CAR corrective action request 改正行动要求corrective action report 改正行动报告FQC运作类AQL Acceptable Quality Level 运作类允收质量水平S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的AOQ Average Output Quality 平均出厂质量AOQL Average Output Quality Level 平均出厂质量Q/R/S Quality/Reliability/Service 质量/可靠度服务MIL-STD Military-Standard 军用标准S I-S IV Special I-Special IV 特殊抽样水平等级P/N Part Number 料号L/N Lot Number 特采AOD Accept On Deviation 特采UAI Use As It 首件检查报告FPIR First Piece Inspection Report 百万分之一PPM Percent Per Million 批号制程统计品管专类SPC Statistical Process Control 统计制程管制SQC Statistical Quality Control 统计质量管理R Range 全距AR Average Range 全距平均值UCL Upper Central Limit 管制上限LCL Lower Central Limit 管制下限MAX Maximum 最大值MIN Minimum 最小值GR&R Gauge Reproducibility&Repeatability 量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径FREQ Frequency 频率N Number 样品数其它质量术语类QCC Quality Control Circle 品质圈QIT Quality Improvement Team 质量改善小组PDCA Plan Do Check Action 计划执行检查总结ZD Zero Defect 零缺点QI Quality Improvement 质量改善QP Quality Policy 目标方针TQM Total Quality Management 全面质量管理MRB Material Reject Bill 退货单LQL Limiting Quality Level 最低质量水平RMA Return Material Audit 退料认可QAN Quality Amelionrate Notice 质量改善活动ADM Absolute Dimension Measuremat 全尺寸测量QT Quality Target 质量目标7QCTools 7 Quality Control Tools 品管七大手法通用之件类ECN Engineering Change Notes 工程变更通知(供货商) ECO Engineering Change Order 工程改动要求(客户) PCN Process Change Notice 工序改动通知PMP Product Management Plan 生产管制计划SIP Specification In Process 制程检验规格SOP Standard Operation Procedure 制造作业规范IS Inspection Specification 成品检验规范BOM Bill Of Material 物料清单PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类QC Quality System 质量系统ES Engineering Standardization 工程标准CGOO China General PCE龙华厂文件H Huston (美国)休斯敦C Compaq (美国)康伯公司C China 中国大陆A Assembly 组装(厂)S Stamping 冲压(厂)P Painting 烤漆(厂)I Intel 英特尔公司T TAIWAN 台湾IWS International Workman Standard 工艺标准ISO International Standard Organization 国际标准化组织GS General Specification 一般规格CMCS C-China M-Manufact C-Compaq S-StampingCompaq产品在龙华冲压厂制造作业规范CQCA Q-Quality A-Assembly Compaq产品在龙华组装厂品管作业规范CQCP P-Painting Compaq产品在龙华烤漆厂品管作业规范部类PMC Production & Material Control 生产和物料控制PPC Production Plan Control 生产计划控制MC Material Control 物料控制ME Manufacture Engineering 制造工程部PE Project Engineering 产品工程部A/C Accountant Dept 会计部P/A Personal & Administration 人事行政部DC Document Center 数据中心QE Quality Engineering 质量工程(部) QA Quality Assurance 质量保证(处) QC Quality Control 质量管理(课) PD Product Department 生产部LAB Labratry 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部P Painting 烤漆(厂)A Asssembly 组装(厂)S Stamping 冲压(厂)生产类PCS Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供货商)标识符SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号其它OEM Original Equipment Manufacture 原设备制造PCE Personal Computer Enclosure 个人计算机外设PC Personal Computer 个人计算机CPU Central Processing Unit 中央处理器SECC SECC` 电解片SGCC SGCC 热浸镀锌材料NHK North of Hongkong 中国大陆PRC People's Republic of China 中国大陆U.S.A the United States of America 美国A.S.A.P As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量VS 以及REV Revision 版本JIT Just In Time 零库存I/O Input/Output 输入/输出OK Ok 好NG Not Good 不行,不合格C=0 Critical=0 极严重不允许ESD Electristatic Discharge 静电排放5S 希腊语整理,整顿,清扫,清洁,教养ATIN Attention 知会CC Carbon Copy 副本复印相关人员APP Approve 核准,认可,承认CHK Check 确认AM Ante Meridian 上午PM Post Meridian 下午CD Compact Disk 光盘CD-ROM Compact Disk Read-Only Memory 只读光盘FDD Floppy Disk Drive 软盘驱动器HDD Hard Disk Drive 碟碟机REF Reference 仅供参考CONN Connector 连接器CA V Cavity 模穴CAD Computer Aid Design 计算器辅助设计ASS'Y Assembly 装配,组装MAT'S Material 材料IC Integrated Circuit 集成电路T/P True Position 真位度TYP Type 类型WDR Weekly Delivery Requirement 周出货需求C/T Cycle Time 制程周期L/T Lead Time 前置时间(生产前准备时间) S/T Standard Time 标准时间P/M Product Market 产品市场3C Computer,Commumcation,Consumer electronic's 消费性电子5WIH When,Where,Who,What,Why,How to5M Man,Machine,Material,Method,Measurement4MIH Man,Material,Money,Method,Time 人力,物力,财务,技术,时间(资源) SQA Strategy Quality Assurance 策略质量保证DQA Design Quality Assurance 设计质量保证MQA Manufacture Quality Assurance 制造质量保证SSQA Sales and service Quality Assurance 销售及服务质量保证LRR Lot Reject Rate 批退率BS Brain storming 脑力激荡EMI Electronic Magnetion Inspect 高磁测试FMI Frequency Modulatim Inspect 高频测试B/M Boar/Molding(flat cable) C/P Connector of PCA/P AssemblySPS Switching power supply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱)DVD Digital Video DiskVCD Video Compact DiskLCD Liquid Crystal DisplayCAD Computer AID DesignCAM Computer AID ManufacturingCAE Computer AID EngineeringABIOS Advanced Basic in put/output system 先进的基本输入/输出系统CMOS Complementary Metal Oxide Semiconductor 互补金属氧化物半导体PDA Personal Digital Assistant 个人数字助理IC Integrated Circuit 集成电路ISA Industry Standard Architecture 工业标准体制结构MCA Micro Channel Architecture 微信道结构EISA Extended Industry Standard Architecture 扩充的工业标准结构SIMM Single in-line memory module 单项导通汇流组件DIMM Dual in-line Memory Module 双项导通汇流组件LED Light-Emitting Diode 发光二级管FMEA Failure Mode Effectiveness 失效模式分析W/H Wire Harness 金属线绪束集组件F/C Flat Cable 扁平电缆PCB Printed Circuit Board 印刷电路板CAR Correction Action Report 改善报告NG Not Good 不良WPR Weekly Delivery Requirement 周出货要求PPM Parts Per Million 百万分之一TPM Total Production Maintenance 全面生产保养MRP Material Requirement Planning 物料需计划OS Operation System 操作系统TBA To Be Design 待定,定缺D/C Drawing ChangeP/P Plans & ProcedureEMI Electrical-Music Industry 电子音乐工业RFI Read Frequency Input 读频输入MMC Maximum Material ConditionMMS Maximum Material SizeLMC Least Material ConditionLMS Least Material Size模具技术用语各种模具常用成形方式accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形shell casting 壳模铸造foam forming 起泡成形sinter forging 烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模landed plunger mold 有肩柱塞式模具burnishing die 挤光模landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具extrusion die 挤出模palletizing die 迭层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 轭型模模具厂常用之标准零配件air vent vale 通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流檔板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 扥架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁)cavity retainer plate 模穴扥板center pin 中心梢clamping block 锁定块coil spring 螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底die block 块形模体die body 铸模座die bush 合模衬套die button 冲模母模die clamper 夹模器die fastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 冲模板die set 冲压模座direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowel hole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drive bearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘脚flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib 凹形拉紧goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶冲头headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar 脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶?lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢locating ring 定位环lock block 压块locking block 定位块locking plate 定位板loose bush 活动衬套making die 打印冲子manifold block 歧管档块master plate 靠模样板match plate 分型板mold base 塑料模座mold clamp 铸模紧固夹mold platen 模用板moving bolster 换模保持装置moving bolster plate 可动侧模板one piece casting 整体铸件parallel block 平行垫块paring line 分模线parting lock set 合模定位器pass guide 穴型导板peened head punch 镶入式冲头pilot pin 导?pin gate 针尖浇口plate 衬板pre extrusion punch 顶挤冲头punch 冲头puncher 推杆pusher pin 衬套梢rack 机架rapping rod 起模杆re-entrant mold 凹入模retainer pin 嵌件梢retainer plate 扥料板return pin 回位梢riding stripper 浮动脱模器ring gate 环型浇口roller 滚筒runner 流道runner ejector set 流道顶出器runner lock pin 流道拉梢screw plug 头塞set screw 固定螺丝shedder 脱模装置shim 分隔片shoe 模座之上下模板shoot 流道shoulder bolt 肩部螺丝skeleton 骨架slag riser 冒渣口slide(slide core) 滑块slip joint 滑配接头spacer block 间隔块spacer ring 间隔环spider 模蕊支架spindle 主轴sprue 注道sprue bushing 注道衬套sprue bushing guide 注道导套sprue lock bushing 注道定位衬套sprue puller 注道拉料spue line 合模线square key 方键square nut 方螺帽square thread 方螺纹stop collar 限位套stop pin 止动梢stop ring 止动环stopper 定位停止梢straight pin 圆柱梢stripper bolt 脱料螺栓stripper bushing 脱模衬套stripper plate 剥料板stroke end block 行程止梢submarine gate 潜入式浇口support pillar 支撑支柱/顶出支柱support pin 支撑梢supporting plate 扥板sweep templete 造模刮板tab gate 辅助浇口taper key 推拔键taper pin 拔锥梢/锥形梢teeming 浇注three start screw 三条螺纹thrust pin 推力销tie bar 拉杵tunnel gate 隧道形浇口vent 通气孔wortle plate 拉丝模板模具常用之工作机械3D coordinate measurement 三次元量床boring machine 搪孔机CNC milling machine CNC铣床contouring machine 轮廓锯床copy grinding machine 仿形磨床copy lathe 仿形车床copy milling machine 仿形铣床copy shaping machine 仿形刨床cylindrical grinding machine 外圆磨床die spotting machine 合模机drilling machine 钻孔机engraving machine 雕刻机engraving E.D.M. 雕模放置加工机form grinding machine 成形磨床graphite machine 石墨加工机horizontal boring machine 卧式搪孔机horizontal machine center 卧式加工制造中心internal cylindrical machine 内圆磨床jig boring machine 冶具搪孔机jig grinding machine 冶具磨床lap machine 研磨机machine center 加工制造中心。

根据国家标准，以下为部分塑料模具成形术语的标准翻译。

模具常用之工作机械动模 Movable Mould Moving Half3D Coordinate Measurement 三次元量床定模座板Fixed Clamp Plate Top Clamping Plate Top Plate Boring Machine 搪孔机动模座板Moving Clamp Plate BottomClamping Plate Bottom PlateCNC Milling Machine CNC铣床上模座板 Upper Clamping Plate Contouring Machine 轮廓锯床下模座板 Lower Clamping Plate Copy Grinding Machine 仿形磨床凹模固定板 Cavity-retainer Plate Copy Lathe 仿形车床型芯固定板 Mould Core-retainer Plate Copy Milling Machine 仿形铣床凸模固定板 Punch-retainer Plate Copy Shaping Machine 仿形刨床模套 Die Body Die Sleeve Die Blank Cylindrical Grinding Machine 外圆磨床支承板 Backing Plate Support Plate Die Spotting Machine 合模机垫块 Spacer Parallel Drilling Machine 钻孔机支架 Ejector Housing Mould Base Leg Engraving Machine 雕刻机模头 Die Head Engraving E.D.M 雕模放置加工机根据国家标准，以下为部分压铸模具术语的标准翻译。

Form Grinding Machine 成形磨床压力铸造模具 Die-Casting Die Graphite Machine 石墨加工机压铸模零部件Horizontal Boring Machine 卧式搪孔机定模 Fixed Die Cover Die Horizontal Machine Center卧式加工制造中心定模座板 Fixed Clamping Plate Internal Cylindrical Machine 内圆磨床定模套板 Bolster Fixed Die Jig Boring Machine 冶具搪孔机动模 Moving Die Ejector Die Jig Grinding Machine 冶具磨床动模座板 Moving Clamping Plate Lap Machine 研磨机直流道 Sprue Machine Center 加工制造中心横流道 Runner Multi Model Miller 靠磨铣床内浇口 Gate NC Drilling Machine NC钻床模具分类NC Grinding Machine NC磨床Injection Mold 注塑模NC Lathe NC车床Plastic Rubber Mould 塑胶模NC Programming System NC程式制作系统Rubber Molding 橡胶成形Planer 龙门刨床Hot Chamber Die Casting 热室压铸Profile Grinding Machine 投影磨床Sand Mold Casting 砂模铸造Projection Grinder 投影磨床Extrusion Mold 挤出模Radial Drilling Machine 旋臂钻床Multi-Cavity Mold 多模穴模具Shaper 牛头刨床Stack Mold, Stack Injection Mould 叠层模Surface Grinder 平面磨床Plaster Mold 石膏模Try Machine 试模机Three Plates Mold 三板模Turret Lathe 转塔车床Plain Die 简易模Universal Tool Grinding Machine万能工具磨床Pierce Die 冲孔模Vertical Machine Center 立式加工制造中心Forming Die 成型模Wire E.D.M 线割放电加工机Progressive Die 连续模入水 GateGang Dies 复合模进入位 Gate LocationShearing Die 剪边模水口形式 Gate TypeCavity Die 型腔模大水口 Edge GateRiveting Die 铆合模细水口 Pin-point GateCompression Molding 压缩成型水口大小 Gate SizeFlash Mold 溢流式模具转水口 Switching Runner GateExtrusion Mold 挤压式模具唧嘴口径 Sprue DiameterSplit Mold 分割式模具流道 Mold RunnerMould Cavity 型腔 母模热流道 Hot Runner Hot ManifoldMold Core 模芯 公模温度控制器温控器ThermostatThermoregulators Temperature Controller Large Die Mold 大型模具热嘴冷流道 Hot Sprue Cold RunnerPrecise Die Mold 精密模具唧嘴直流 Direct Sprue GateComplex Die Mold 复杂模具圆形流道 Round Full Half RunnerFoaming Mould 发泡模具流道电脑分析 Mold Flow AnalysisMetal Die 金属模具流道平衡 Runner BalancePlastic Mold 塑料模具热嘴 Hot SpruePress Tool Stamping Die Punch Die冲压模具热流道板 Hot ManifoldExtrusion Die 挤压模具发热管 Cartridge HeaterGraphite Die 石墨模具探针 Thermocouples流道浇口部分插头 Connector PlugRunner System 浇道系统插座 Connector SocketSprue Cold Material Trap 浇道 冷料井密封 封料 SealSprue Puller 拉杆运水 Water LineRunner Design 流道设计喉塞 Line Plug Throat TapsMain Runner 主流道喉管 TubeSecondary Runner 次流道塑胶管 Plastic TubeMould Gate Design 浇口设计快速接头Jiffy Quick Connector QuickDisconnect CouplingSubmarine Gate 潜伏浇口模具零件 Mold ComponentsTunnel Gate 隧道式浇口三板模 3-Plate MoldPinpoint Gate 点浇口二板模 2-Plate MoldFan Gate 扇形浇口边钉 导边 Leader Pin Guide PinSide Gate 侧浇口边司 导套 Bushing Guide BushingEdge Gate 侧缘浇口中托司 Shoulder Guide BushingTab Gate 搭接浇口中托边 Guide PinFilm Gate 薄膜浇口顶针板 Ejector Retainner PlateFlash Gate 闸门浇口托板 Support PlateSlit Gate 缝隙浇口螺丝 ScrewDish Gate 盘形浇口管钉 Dowel PinDiaphragm Gate 隔膜浇口开模槽 Ply Bar ScotRing Gate 环形浇口内模管位 Core Cavity inter-LockRunnerless 无浇道顶针 Ejector PinSprueless 无射料管方式司筒 Ejector SleeveLong Nozzle 延长喷嘴方式司筒针 Ejector PinSprue 浇口，溶渣推板Eject Plate Push Plate StripperPlateInsulated Runner Hot Runner 热浇道缩呵 Movable Core Return Core Puller Runner Plat 浇道模块扣机（尼龙拉勾） Nylon Latch LockValve Gate阀门浇口斜顶 LifterSlag Well 冷料井模胚（架） Mold BaseCold Slag 冷料渣上内模 Cavity InsertSprue Gate 射料浇口，直浇口下内模 Core InsertNozzle 射嘴行位（滑块） SlideSprue Lock Pin 料头钩销（拉料杆）镶件 Insert注塑缺陷压座 WedgeFlash 飞边耐磨板 油板 Wedge Wear PlateWarpage 翘曲压条 PlateAir Trap 积风撑头 Support PillarBlush 发赤唧嘴 Sprue BushingFlow Line 流痕挡板 Stop PlateSplay 银纹定位圈 Locating RingShort Shot 短射锁扣 LatchSink Mark 缩痕扣机 Parting Lock SetStreak 条纹推杆 Push BarVoid 缩孔栓打螺丝 S.H.S.BWeld Line 熔接线顶板 Ejector PlateGas Mark 烧焦活动臂 Lever ArmCold Slug 冷斑分流锥 Sprue SpreaderDelamination 起皮分流板 Spreader PlateBurr 毛刺水口司 BushFlaw Scratch 刮伤垃圾钉 Stop PinGloss 光泽隔片 BuffleGlazing 光滑弹弓柱 Spring RodSurface Check 表面裂痕弹弓 Die SpringHesitation 迟滞中托司 Ejector Guide Bush注塑工艺中托边 Ejector Guide PinMolding Conditions 成型条件镶针 PinDrying 烘干销子 Dowel PinBarrel Temperature 料筒温度波子弹弓 Ball catchMelt Temperature 熔化温度喉塞 Pipe PlugMold Temperature 模具温度锁模块 Lock PlateInjection Pressure 注塑压力斜顶 Angle from PinBack Pressure 背压斜顶杆 Angle Ejector RodInjection Speed 注塑速度尼龙拉勾 Parting LocksScrew Speed 螺杆转速活动臂 Lever ArmTensile Strength 抗拉强度复位键 提前回杆 Early Return BarTensile Elongation 延伸率气阀 ValvesFlexural Modulus 弯曲模数斜导边 Angle PinFlexural Strength 抗弯强度术语 TermsShrinkage 收缩率承压平面平衡Parting Surface SupportBalanceRegrind Usage 次料使用模排气 Parting Line VentingMoulding 模塑回针碰料位Return Pin and CavityInterference机械设备顶针碰运水Water Line Interferes withEjector PinLathe 车床料位出上下模Part from Cavith（Core）SidePlaner 刨床不准用镶件Do Not Use（Core Cavity）InsertMiller Milling Machine 铣床用铍铜做镶件 Use Beryllium Copper Insert Grinder 磨床初步模图设计 Preliminary Mold Design Driller 钻床正式模图设计 Final Mold DesignLinear Cutting 线切割弹弓压缩量 Spring Compressed length Electrical Sparkle 电火花稳定性好 Good Stability StableWelder 电焊机强度不够 Insufficient RigidityPunching Machine 冲床均匀冷却 Even CoolingRobot 机械手扣模 StickingCommon Equipment 常用设备热膨胀 Thermal ExpansionEDM Electron Discharge Machining放电加工公差 Tolerance3D Coordinate Measurement 三次元量床铜公（电极） Copper Electrode Boring Machine 搪孔机Air Vent Valve 通气阀Contouring Machine 轮廓锯床Anchor Pin 锚梢Copy Grinding Machine 仿形磨床Angular Pin 角梢Cylindrical Grinding Machine 外圆磨床Baffle 调节阻板Die Spotting Machine 合模机Angular Pin 倾斜梢Engraving Machine 雕刻机Baffle Plate 折流挡板Engraving E.D.M 雕模放置加工机Ball Button 球塞套Form Grinding Machine 成形磨床Ball Plunger 定位球塞Graphite Machine 石墨加工机Ball Slider 球塞滑块Horizontal Boring Machine 卧式搪孔机Binder Plate 压板Horizontal Machine Center卧式加工制造中心Blank Holder 防皱压板Internal Cylindrical Machine 内圆磨床Blanking Die 落料冲头模具零件Bolster 上下模板Top Plate 上托板（顶板）Bottom Board 浇注底板Top Block 上垫脚Bolster 垫板Punch Set 上模座Bottom Plate 下固定板Punch Pad 上垫板Bracket 托架Punch Holder 上夹板Bumper Block 缓冲块Stripper Pad 脱料背板Buster 堵口Up Stripper 上脱料板Casting Ladle 浇注包Male Die 公模（凸模）Casting Lug 铸耳Feature Die 公母模Cavity 模腔 模穴（模仁）Female Die 母模（凹模）Cavity Retainer Plate 模穴托板Upper Mold Plate 上模板Center Pin 中心梢Lower Mold Plate 下模板Clamping Block 锁定块Die Pad 下垫板Coil Spring 螺旋弹簧Die Holder 下夹板Cold Punched Nut 冷冲螺母Die Set 下模座Cooling Spiral 螺旋冷却栓Bottom Block 下垫脚Core 心型Bottom Plate下托板（底板）Core Pin 心型梢Stripping Plate 内外打（脱料板）Cotter 开口梢Outer Stripper 外脱料板Cross 十字接头Inner Stripper 内脱料板Cushion Pin 缓冲梢Lower Stripper 下脱料板Diaphragm Gate 盘形浇口Inner Guiding Post 内导柱Die Approach 模头料道Inner Hexagon Screw 内六角螺钉Die Bed 型底Dowel Pin 固定销Die Block 块形模体Mould Coil Spring 模具弹簧Die Body 模体Lifter Pin 顶料销Die Body 铸模座Isoheight Sleeve 等高套筒Die Bush 合模衬套Pin 销Die Button 冲模母模Lifter Guide Pin 浮升导料销Die Clamper 夹模器Guide Pin 导正销Die Fastener 模具固定用零件Wire Spring 圆线弹簧Die Holder 母模固定板Outer Guiding Post 外导柱Die Lip 模唇Stop Screw 止付螺丝Die Plate 冲模板Located Pin 定位销Die Set 冲压模座Outer Bush 外导套Direct Gate 直接浇口Punch 冲头Dog Chuck 爪牙夹头Insert 入块（嵌入件）Dowel 定位梢Deburring Punch 压毛边冲子Dowel Hole 导套孔Groove Punch 压线冲子Dowel Pin 合模梢Stamped Punch 字模冲子Dozzle 辅助浇口Round Punch 圆冲子Dowel Pin 定位梢Special Shape Punch 异形冲子Draft 拔模锥度Bending Block 折刀Draw Bead 张力调整杆Roller 滚轴Drive Bearing 传动轴承Baffle Plate 挡块Ejection Pad 顶出衬垫Located Block 定位块Ejector 脱模器Supporting Block for Location 定位支承块Ejector Guide Pin 顶出导梢Air Cushion Plate 气垫板Ejector Leader Bush 顶出导梢衬套Air-Cushion Eject-rod 气垫顶杆Ejector Pad 顶出垫Trimming Punch 切边冲子Ejector Pin 顶出梢Stiffening Rib Punch Stinger 加强筋冲子Ejector Plate 顶出板Ribbon Punch 压筋冲子Ejector Rod 顶出杆Reel-stretch Punch 卷圆压平冲子Ejector Sleeve 顶出衬套Guide Plate 定位板Ejector Valve 顶出阀Sliding Block 滑块Eye Bolt 环首螺栓Sliding Dowel Block 滑块固定块Filling Core 填充型芯 椿入蕊Active Plate 活动板Film Gate 薄膜形浇口Lower Sliding Plate 下滑块板Finger Pin 指形梢Upper Holder Block 上压块Finish Machined Plate 角形模板Upper Mid Plate 上中间板Finish Machined Round Plate 圆形模板Spring Box 弹簧箱Fixed Bolster Plate 固定侧模板Spring-Box Eject-rod 弹簧箱顶杆Flanged Pin 带凸缘针Spring-Box Eject-Plate 弹簧箱顶板Flash Gate 毛边形浇口Bushing Block Liner Bushing 衬套Flask 上箱Cover Plate 盖板Floating Punch 浮动冲头Guide Pad 导料块Gate 浇口模具技术用语Gate Land 浇口面各种常用模具成形方式Gib 凹形拉紧楔Accurate Die Casting 精密压铸Goose Neck 鹅颈管Powder Forming 粉末成形Guide Bushing 引导衬套Calendaring Molding 压延成形Guide Pin 导梢Powder Metal Forging 粉末锻造Guide Post 引导柱Cold Chamber Die Casting 冷式压铸Guide Plate 导板Precision Forging 精密锻造Guide Rail 导轨Cold Forging 冷锻Head Punch 顶头冲孔Press Forging 冲锻Headless Punch 直柄冲头Compacting Molding 粉末压出成形Heavily Tapered Solid 整体模蕊盒Rocking Die Forging 摇动锻造Hose Joint Pipe Coupler 管接头Compound Molding 复合成形Impact Damper 缓冲器Rotary Forging 回转锻造Injection Ram 压射柱塞Compression Molding 压缩成形Inlay Bush 嵌入衬套Rotational Molding 离心成形Inner Plunger 内柱塞Dip Mold 浸渍成形Inner Punch 内冲头Rubber Molding 橡胶成形Inserts 嵌件Encapsulation Molding 注入成形Insert Pin 嵌件梢Sand Mold Casting 砂模铸造King Pin 转向梢Extrusion Molding 挤出成形King Pin Bush 主梢衬套Shell Casting 壳模铸造Knockout Bar 脱模杵Foam Forming 发泡成形Land 合模平坦面Sinter Forging 烧结锻造Land Area 合模面Forging Roll 轧锻Leader Bush 导梢衬套Six Sides Forging 六面锻造Lifting Pin 起模顶针Gravity Casting 重力铸造Lining 内衬Slush Molding 凝塑成形Locating Center Punch 定位中心冲头Hollow Blow Molding 中空（吹出）成形Locating Pilot Pin 定位导梢Squeeze Casting 高压铸造Locating Ring 定位环Hot Chamber Die Casting 热室压铸Lock Block 压块Swaging 挤锻Locking Block 定位块Hot Forging 热锻Locking Plate 定位板Transfer Molding 转送成形Loose Bush 活动衬套Injection Molding 射出成形Making Die 打印冲子Warm Forging 温锻Manifold Block 歧管档块Investment Casting 精密铸造Master Plate 靠模样板Matched Die Method 对模成形法Match Plate 分型板Laminating Method 被覆淋膜成形Mold Base 塑胶模座Low Pressure Casting 低压铸造Mold Clamp 铸模紧固夹Lost Wax Casting 脱蜡铸造Mold Platen 模用板Matched Mould Thermal Forming对模热成形Moving Bolster 换模保持装置模Close Mold 合模Moving Bolster Plate 可动侧模板Demould 脱模 脱模剂One Piece Casting 整体铸件Mould Unloading 开模Parallel Block 平行垫块Eject 顶出Parting Line 分模线Tool Change Retooling Die Changing 换模Parting Lock Set 合模定位器Mould Clamping 锁模Pass Guide 穴型导板各式模具分类用语Peened Head Punch 镶入式冲头 钻杆凸模Bismuth Mold 铋铸模Pilot Pin 定位销 导向销子Landed Plunger Mold 有肩柱塞式模具Pin Gate 针尖浇口Burnishing Die 挤光模Plate 衬板Landed Positive Mold 有肩全压式模具Pre Extrusion Punch 顶挤冲头Button Die 镶入式圆形凹模Punch 冲头Loading Shoe Mold 料套式模具Puncher 推杆Center-Gated Mold 中心浇口式模具Pusher Pin 衬套梢Loose Detail Mold 活零件模具Rack 机架Chill Mold 冷硬用铸模Rapping Rod 起模杆Loose Mold 活动式模具Re-entrant Mold 凹入模Cold Hobbing 冷挤压制模法Retainer Pin 嵌件梢Louvering Die 百叶窗冲切模Retainer Plate 托料板Composite Dies 复合模具Return Pin 回位梢Manifold Die 分歧管模具Riding Stripper 浮动脱模器Counter Punch 反凸模Ring Gate 环型浇口Modular Mold 组合模具Roller 滚筒Double Stack Mold 双层模具Runner 流道Multi-Cavity Mold 多模穴模具Runner Ejector Set 流道顶出器Electroformed Mold 电铸成形模Runner Lock Pin 流道拉梢Multi-Gate Mold 复式浇口模具Screw Plug 头塞Expander Die 扩径模Set Screw 固定螺丝Offset Cold Bending Die 双折冷弯模具Shedder 脱模装置Extrusion Die 挤出模Shim 分隔片Stack Mold, Stack Injection Mould 叠层模Shoe 模座之上下模板Family Mold 反套制品模具Shoot 流道Plaster Mold 石膏模Shoulder Bolt 肩部螺丝Blank Through Dies 漏件式落料模Skeleton Frameworks 骨架Porous Mold 通气性模具Slag Riser 冒渣口Duplicated Cavity Plate 复板模Slide（Slide Core） 滑块Positive Mold 全压式模具Slip Joint 滑配接头Fantail Die 扇尾形模具Spacer Block 间隔块Pressure Die 压紧模Spacer Ring 间隔环Fishtail Die 鱼尾形模具Spider 模蕊支架Profile Die 轮廓模Spindle 主轴Flash Mold 溢料式模具Sprue 注道Progressive Die 顺序模Sprue Bushing 注道衬套Gypsum Mold 石膏铸模Sprue Bushing Guide 注道导套Portable Mold 手提式模具Sprue Lock Bushing 注道定位衬套Hot-Runner Mold 热流道模具Sprue Puller 注道残料顶销 浇道推出杆Prototype Mold 雏形试验模具 原型模具Sprue Line 合模线Ingot Mold 钢锭模Square Key 方键Punching Die 落料模Square Nut 方螺帽Lancing Die 切口模 切缝模Square Thread 方螺纹Raising（Embossing） 压花起伏成形Stop Collar 限位套Re-entrant Mold 倒角式模具Stop Pin 止动梢Sectional Die 拼合模Stop Ring 止动环Runless Injection Mold 无流道冷料模具Stopper 定位停止梢Sectional Die 对合模具Straight Pin 圆柱销Segment Mold 组合模Stripper Bolt 脱料螺栓Semi-Positive Mold 半全压式模具Stripper Bushing 脱模衬套Shaper 定型模套Stripper Plate 剥料板Single Cavity Mold 单腔模具Stroke End Block 行程止梢Solid Forging Die 整体锻模Submarine Gate 潜入式浇口Split Forging Die 拼合锻模Support Pillar 支撑支柱 顶出支柱Split Mold 双并式模具Support Pin 支撑梢Sprueless Mold 无注道残料模具Supporting Plate 托板Squeezing Die 挤压模Sweep Template 造模刮板Stretch Form Die 拉伸成形模Tab Gate 辅助浇口Sweeping Mold 平刮铸模Taper Key 推拔键Swing Die 振动模具Taper Pin 拔锥梢 锥形梢Three Plates Mold 三片式模具Teeming 浇注Trimming Die 切边模Three Start Screw 三条螺纹Unit Mold 单元式模具Thrust Pin 推力销Universal Mold 通用模具Tie Bar 拉杵Unscrewing Mold 退扣式模具Tunnel Gate 隧道形浇口Yoke Type Die 轭型模Vent 通气孔模具厂常用之标准零配件Wortle Plate 拉丝模板Air Vent Valve 通气阀Pierce 冲孔Anchor Pin 锚梢Forming 成型（抽凸 冲凸）Angular Pin 角梢Draw Hole 抽孔Baffle 调节阻板Bending 折弯Angular Pin 倾斜梢Trim 切边Baffle Plate 折流档板Emboss 凸点Ball Button 球塞套Dome 凸圆Ball Plunger 定位球塞Semi-Shearing 半剪Ball Slider 球塞滑块Stamp Mark 冲记号Binder Plate 压板Deburr or Coin 压毛边Blank Holder 防皱压板Punch Riveting 冲压铆合Blanking Die 落料冲头Side Stretch 侧冲压平Bolster 上下模板Reel Stretch 卷圆压平Bottom board 浇注底板Groove 压线Bolster 垫板Blanking 下料Bottom Plate 下固定板Stamp Letter 冲字（料号）Bracket 托架Shearing 剪断Bumper Block 缓冲块Tick-Mark Nearside 正面压印Buster 堵口Tick-Mark Farside 反面压印Casting Ladle 浇注包Extension Drawing 展开图Casting lug 铸耳procedure Drawing 工程图Cavity 模穴（模仁）Die Structure Drawing 模具结构图Cavity Retainer Plate 模穴托板Material 材质Center Pin 中心梢Material Thickness 料片厚度Clamping Block 锁定块Factor 系数Coil Spring 螺旋弹簧Upward 向上Cold Punched Nut 冷冲螺母Downward 向下Cooling Spiral 螺旋冷却栓Press Specification 冲床规格Core 心型Die Height Range 适用模高Core Pin 心型梢Die Height 闭模高度Cotter 开口梢Burr 毛边Cross 十字接头Gap 间隙Cushion Pin 缓冲梢Weight 重量Diaphragm Gate 盘形浇口Total Weight 总重量Die Approach 模头料道Punch Weight 上模重量Die Bed 型底Compression Molding 压缩成型Die Block 块形模体Flash Mold 溢流式模具Die Body 铸模座Extrusion Mold 挤压式模具Die Bush 合模衬套Split Mold 分割式模具Die Button 冲模母模Cavity 型腔 母模Die Clamper 夹模器Mold Core 模芯 公模Die Fastener 模具固定用零件Taper 锥拔Die Holder 母模固定板Leather Cloak 仿皮革Die Lip 模唇Shiver 饰纹Die Plate 冲模板Flow Mark 流痕Die Set 冲压模座Welding Mark 溶合痕Direct Gate 直接浇口Post Screw Insert 螺纹套筒埋值Dog Chuck 爪牙夹头Self Tapping Screw 自攻螺丝Dowel 定位梢Striper Plate 脱料板Dowel Hole 导套孔Piston 活塞Dowel Pin 合模梢Cylinder 汽缸套Dozzle 辅助浇口Chip 细碎物Dowel Pin 定位梢Handle Mold 手持式模具Draft 拔模锥度Encapsulation Molding 低压封装成型Draw Bead 张力调整杆Two Plate 两极式（模具）Drive Bearing 传动轴承Well Type 蓄料井Ejection Pad 顶出衬垫Insulated Runner 绝缘浇道方式Ejector 脱模器Hot Runner 热浇道Ejector Guide Pin 顶出导梢Runner Plat 浇道模块Ejector Leader Bush 顶出导梢衬套Valve Gate 阀门浇口Ejector Pad 顶出垫Band Heater 环带状的电热器Ejector Pin 顶出梢Spindle 阀针Ejector Plate 顶出板Spear Head 刨尖头Ejector Rod 顶出杆Slag Well 冷料井Ejector Sleeve 顶出衬套Cold Slag 冷料渣Ejector Valve 顶出阀Air Vent 排气道Eye Bolt 环首螺栓Welding Line 熔合痕Filling Core 填充型芯 椿入蕊Eject Pin 顶出针Film Gate 薄膜形浇口Knock Pin 顶出销Finger Pin 指形梢Return Pin 回位销反顶针Finish Machined Plate 角形模板Sleeve 套筒Finish Machined Round Plate 圆形模板Stripper Plate 脱料板Fixed Bolster Plate 固定侧模板Insert Core 放置入子Flanged Pin 带凸缘针Runner Stripper Plate 浇道脱料板Flash Gate 毛边形浇口Guide Pin 导销Flask 上箱Eject Rod （Bar）（成型机）顶业捧Floating Punch 浮动冲头Subzero 深冷处理Gate 浇口Three Plate 三极式模具Gate Land 浇口面Runner System 浇道系统Gib 凹形拉紧楔Stress Crack 应力电裂Goose Neck 鹅颈管Orientation 定向Guide Bushing 引导衬套Sprue Gate 射料浇口，直浇口Guide Pin 导梢Nozzle 射嘴Guide Post 引导柱Sprue Lock Pin 料头钩销（拉料杆）Guide Plate 导板Slag Well 冷料井Guide Rail 导轨Side Gate 侧浇口Head Punch 顶头冲孔Edge Gate 侧缘浇口Headless Punch 直柄冲头Tab Gate 搭接浇口Heavily Tapered Solid 整体模蕊盒Film Gate 薄膜浇口Hose Nippler 管接头Flash Gate 闸门浇口Impact Damper 缓冲器Slit Gate 缝隙浇口Injection Ram 压射柱塞Fan Gate 扇形浇口Inlay Bush 嵌入衬套Dish Gate 因盘形浇口Inner Plunger 内柱塞Diaphragm Gate 隔膜浇口Inner Punch 内冲头Ring Gate 环形浇口Insert 嵌件Submarine Gate 潜入式浇口Insert Pin 嵌件梢Tunnel Gate 隧道式浇口King Pin 转向梢Pin Gate 针点浇口King Pin Bush 主梢衬套Runnerless 无浇道Knockout Bar 脱模杵Sprueless 无射料管方式Land 合模平坦面Long Nozzle 延长喷嘴方式Land Area 合模面Sprue 浇口 溶渣Leader Bush 导梢衬套Landed Plunger Mold 有肩柱塞式模具Lifting Pin 起模顶针 起模杆Burnishing Die 挤光模Lining 内衬Landed Positive Mold 有肩全压式模具Locating Center Punch 定位中心冲头Button Die 镶入式圆形凹模Locating Pilot Pin 定位导梢Loading Shoe Mold 料套式模具Locating Ring 定位环Center-Gated Mold 中心浇口式模具Lock Block 压块Loose Detail Mold 活零件模具Locking Plate 定位板Loose Mold 活动式模具Loose Bush 活动衬套Cold Hobbing 冷挤压制模Making Die 打印冲子Louvering Die 百叶窗冲切模Manifold Block 歧管档块Composite Dies 复合模具Master Plate 靠模样板Manifold Die 分歧管模具Match Plate 分型板Counter Punch 反凸模Mold Base 塑胶模座Modular Mold 组合式模具Mold Clamp 铸模紧固夹Double Stack Mold 双层模具Mold Platen 模用板Multi-Cavity Mold 多模穴模具Moving Bolster 换模保持装置Electroformed Mold 电铸成形模Moving Bolster Plate 可动侧模板Multi-Gate Mold 复式浇口模具One Piece Casting 整体铸件Expander Die 扩径模Parallel Block 平行垫块Offset Bending Die双折冷弯模具偏移弯曲模Parting Line 分模线Extrusion Die 挤出模Parting Lock Set 合模定位器Palletizing Die 叠层模Pass Guide 穴型导板Family Mold 反套制品模具Peened Head Punch镶入式冲头锤击强化冲头Plaster Mold 石膏模钻杆凸模Pilot Pin 定位销 导向销子Blank Through Dies 漏件式落料模Pin Gate 针尖浇口Porous Mold 通气性模具Plate 衬板Duplicated Cavity Plate 复板模Pre Extrusion Punch 顶挤冲头Positive Mold 全压式模具Punch 冲头Fantail Die 扇尾形模具Puncher 推杆Pressure Die 压紧模Pusher Pin 衬套梢Fishtail Die 鱼尾形模具Rack 机架Profile Die 轮廓模Rapping Rod 起模杆Flash Mold 溢料式模具Re-entrant Mold 凹入模Progressive Die 顺序模Retainer Pin 嵌件梢Gypsum Mold 石膏铸模Retainer Plate 托料板Portable Mold 手提式模具Return Pin 回位梢Hot-Runner Mold 热流道模具Riding Stripper 浮动脱模器Prototype Mold 雏形试验模具Ring Gate 环型浇口Ingot Mold 钢锭模Roller 滚筒Punching Die 落料模Runner 流道Lancing Die 切口模Runner Ejector Set 流道顶出器Raising（Embossing） 压花起伏成形Runner Lock Pin 流道拉梢Re-entrant Mold 倒角式模具Screw Plug 头塞Sectional Die 拼合模Set Screw 固定螺丝Runnerless Injection Mold 无流道冷料模具Shedder 脱模装置Sectional Die 对合模具Shim 分隔片Segment Mold 组合模Shoot 流道Shaper 定型模套Shoulder Bolt 肩部螺丝Single Cavity Mold 单腔模具Skeleton 骨架Solid Forging Die 整体锻模Slag Riser 冒渣口Split Forging Die 拼合锻模Slide（Slide Core） 滑块Split Mold 双并式模具Slip Joint 滑配接头Sprueless Mold 无注道残料模具Spacer Block 间隔块Squeezing Die 挤压模Spacer Ring 间隔环Stretch Form Die 拉伸成形模Spider 模蕊支架Sweeping Mold 平刮铸模Spindle 主轴Swing Die 振动模具Sprue 注道Three Plates Mold 三片式模具Sprue Bushing 注道衬套Trimming Die 切边模Sprue Bushing Guide 注道导套Unit Mold 单元式模具Sprue Lock Bushing 注道定位衬套Universal Mold 通用模具Sprue Puller注道拉料浇道推出杆注道残料Unscrewing Mold 退扣式模具顶销Spew Line 合模线Yoke Type Die 轭型模Square Key 方键Accurate Die Casting 精密压铸Square Nut 方螺帽Powder Forming 粉末成形Square Thread 方螺纹Calendaring Molding 压延成形Limit Stop Collar 限位套Powder Metal Forging 粉末锻造Stop Pin 止动梢Cold Chamber Die Casting 冷式压铸Stop Ring 止动环Precision Forging 精密锻造Stopper 定位停止梢Cold Forging 冷锻Straight Pin 圆柱销Press Forging 冲锻Stripper Bolt 脱料螺栓Compacting Molding 粉末压出成形Stripper Bushing 脱模衬套Rocking Die Forging 摇动锻造Stripper Plate 剥料板Compound Molding 复合成形Stroke End Block 行程止梢Rotary Forging 回转锻造Submarine Gate 潜入式浇口Compression Molding 压缩成形Support Pillar 支撑支柱 顶出支柱Rotational Molding 离心成形Support Pin 支撑梢Dip Mold 浸渍成形Supporting Plate 托板Rubber Molding 橡胶成形Sweep Template 造模刮板Encapsulation Molding 注入成形Tab Gate 辅助浇口Sand Mold Casting 砂模铸造Taper Key 推拔键Extrusion Molding 挤出成形Taper Pin 拔锥梢 锥形梢Shell Casting 壳模铸造Teeming Pouring 浇注Foam Forming 发泡成形Three Start Screw 三条螺纹Sinter Forging 烧结锻造Thrust Pin 推力销Forging Roll 轧锻Tie Bar 拉杵Six Sides Forging 六面锻造Vent 通气孔Slush Molding 凝塑成形Wortle Plate 拉丝模板Hollow（Blow） Molding 中空（吹出）成形Squeeze Casting 高压铸造Hot Chamber Die Casting 热室压铸Swaging 挤锻Hot Forging 热锻Transfer Molding 转送成形Injection Molding 射出成形Warm Forging 温锻Investment Casting 精密铸造Matched Die Method 对模成形法Laminating Method 被覆淋膜成形Low Pressure Casting 低压铸造Lost Wax Casting 脱蜡铸造Matched Mould Thermal Forming对模热成形模Barreling 滚光加工Belling 压凸加工Bending 弯曲加工Blanking 下料加工Bulging 撑压加工Burring 冲缘加工Cam Die Bending 凸轮弯曲加工Caulking 压合加工Coining 压印加工Compressing 压缩加工Compression Bending 押弯曲加工Crowning 凸面加工Curl Bending 卷边弯曲加工Curling 卷曲加工Cutting 切削加工Dinking 切断蕊骨Double Shearing 叠板裁断Drawing 引伸加工Drawing with Ironing 抽引光滑加工Embossing 浮花压制加工Extrusion 挤制加工Filing 锉削加工Fine Blanking 精密下料加工Finish Blanking 光制下料加工Finishing 精整加工Folding 折边弯曲加工Folding 折叠加工Forming 成形加工Impact Extrusion 冲击挤压加工Indenting 压痕加工Ironing 引缩加工Knurling 滚花Lock Seaming 固定接合Louvering 百叶窗板加工MarKing 刻印加工Necking 颈缩加工Notching 冲口加工Parting 分断加工Piercing 冲孔加工Progressive Bending 连续弯曲加工Progressive Blanking 连续下料加工Progressive Drawing 连续引伸加工Progressive Forming 连续成形加工Reaming 铰孔加工Restriking 二次精冲加工 矫形锻压Riveting 铆接加工Roll Bending 滚筒弯曲加工Roll Finishing 滚压加工Rolling 压延加工Roughing 粗加工Scrapless Machining 无废料加工Seaming 折弯重叠加工Shaving 缺口修整加工Shearing 切断加工Sizing 精压加工 矫正加工Slitting 割缝加工Spinning 卷边旋接Staking 铆固Stamping 锻压加工Swaging 挤锻压加工Trimming 整缘加工Upsetting 锻粗加工 顶锻镦粗Wiring 抽线加工Aberration 色差Atomization 雾化Bite 咬入Blacking Hole 涂料孔（铸疵）Blacking Scab 涂料疤Blister 起泡Blooming 起霜Blow Hole 破孔Blushing 泛白Body Wrinkle 侧壁皱纹Breaking-in 冒口带肉Bubble 膜泡Burn Mark 糊斑Flash Burr 毛边Camber Warpage 翘曲Cell 气泡Center Buckle 表面中部波皱Check 细裂痕Checking 龟裂Chipping 修整表面缺陷Clamp-off 铸件凹痕Collapse 塌陷Color Mottle 色斑Corrosion 腐蚀Crackle 裂痕 裂纹Crazing 碎裂Crazing 龟裂Distortion Deformation 变形Edge 切边碎片Edge Crack 裂边Fading 退色Filler Speak 填充料斑Fissure 裂纹Flange Wrinkle 凸缘起皱Flaw 刮伤Flow Mark 流痕Galling 毛边Glazing 光滑Gloss 光泽Grease Pits 污斑Grinding Defect 磨痕Haircrack 发裂Incrustation 水锈Indentation 压痕Internal Porosity 内部气孔Mismatch 偏模Mottle 斑点Necking 缩颈Nick 割痕Orange peel 橘皮状表面缺陷Overflow 溢流Peeling 剥离Pit 坑Pitting Corrosion 点状腐蚀Plate Mark 模板印痕Pock 麻点Pock Mark 痘斑Resin Streak 树脂流纹Resin Wear 树脂脱落Riding 凹陷Sagging 松垂Saponification 皂化Scar 疤痕Scrap 废料Scrap Jam 废料阻塞Scratch 刮伤 划痕Scuffing 深冲表面划伤Seam 裂痕Shock Line 模口挤痕Short Shot 充填不足Shrinkage Pool 凹孔Sink Mark 凹痕Skin Inclusion 表皮折叠Straightening 矫直Streak 条状痕Surface Check 表面裂痕Surface Roughening 橘皮状表皮皱折Surging 波动Sweat Out 冒汗Torsion Distortion 扭曲Warpage 翘曲Waviness 波痕Weld Mark 焊痕Whitening 白化Wrinkle 皱纹Gas Aassisted Technology 气辅Bottle Cap Mold 瓶盖模具。

工厂专业英语术语Assembly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Pneumatic screw driver气动起子worktable 工作桌OO BA开箱检查fit together组装在一起fasten锁紧(螺丝) fixture 夹具(治具) pallet栈板b arcode条码barcode scanner条码扫描器fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cos metic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs. inch 镑、英寸EMI gasket导电条front plate前板rear plate后板chassis 基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试Voltage switch of SPS 电源电压接拉键sheet metal parts 冲件plastic parts塑胶件SOP制造作业程序material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线left fork叉车personnel resource departmen t 人力资源部production department生产部门planning department企划部QC Secti on品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common e quipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床planer |'plein?|刨床miller铣床grinder磨床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager | =vice manager副理section supervisor课长deputy section supervisor =vice section superisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |'skr?pid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |' ksi'dei?n|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓administration/general affairs dept总务部automatic screwdriver电动启子thicknes s gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单location地点present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheet PCE组装厂生产排配表model机锺work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet 库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked 待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet 年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list 备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die butto n圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopp er清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetizat ion去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料deg rease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products 报放心品defective products不良品finished products成品disposed products处理品barcode 条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer 备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting m achine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction =interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕?? shine 亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grai n细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenchi ng淬火tempering回火annealing退火carbonization碳化tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机。

（工厂管理）工厂术语（英语）CORPORATE COMMON ABBREVIATION常用语缩写1 Organization组织1-1 HQ Head Quarter 总公司1-2Chairmen主席1-3Lite-On Group光宝集团1-4 President 总裁1-5Executive Vice President 常务副总裁1-6Vice President副总裁1-7HR Human Resource人力资源部1-8FIN Finance 财务1-9Sales 销售1-10R&D Research & Developing 研发部1-11QA 质量保证QA DQA CS1-12MIS Management Information System资讯管理系统1-13Pur 采购Purchasing1-14IMD Image management division 影像管理事业部1-15ITS information technology system 计算机部1-16QRA quality reliability assurance 品保部1-17MFG manufacturing 制造部1-18PMC production &material control 生(产)物(料)管(理) 1-19 PRO Procuremnet 采购开发部1-20 PMO Plant Manager Office 厂长室1-21 CEO Chief Executive Officer 执行总裁2 Materials 材料2-1PC Production Control 生产控制2-1-1MPS Mass Production Schedule 量产计划2-1-2FGI Finished goods Inventory 成品存货2-1-3UTS Units To Stock存货单元2-1-4WIP Working In Process Inventory在制品2-1-5C/T Cycle Time 循环时间,瓶颈2-1-6WD Working Days 工作天2-1-7MTD Month To Days 月初到今日(例如总表整理)2-1-8YTD Year To Days 年初到今日2-1-9 SO Sales Order 销售单2-1-10MO Manufacture Order 制造单2-1-11 BTO Build T o Order 订单生产2-1-12 P/N part number 料号2-1-13 FCST Forecast 预测计划2-1-14 W/O Working Order 工单2-1-15 P/O Purchasing Order 采购单2-1-16 VDS Vendor Delivery Schedule 厂商送货进度表2-1-17 D/C Delivery Order 交货单2-2 MC Material Control材料控制2-2-1 MRP Material Requisition plan 材料申请计划2-2-2 INV Inventory 存货清单; Invoice 发票2-2-3 Inv Turn Over Days=INV$/NSB X WD 库存周转天数2-2-4 PSI Production Shipping Inventory 预备待出货2-2-5 JIT Just In Time 实时，准时制、零库存2-2-6 Safety Inventory 安全存量2-2-7 CKD Completed Kits Delivery全件组装出货2-2-8 SKD Semi Kits Delivery半件(小件)组装出货2-3 W/H Warehouse 仓库2-3-1 Rec Receiving Center 接收中心2-3-2 Raw MTL 原物料2-3-3 F/G finish goods 成品2-3-4 GRN Goods Received Note 货物接收单2-4 Import/Export进出口2-4-1 SI Shipping Instruction发货指令2-4-2 PL Packing List包装清单2-4-3 Inv Shipping Invoice出货发票2-4-4 ETD Estimated Time of Departure 预估离开时间2-4-5 ETA Estimated Time of Arrive 预估到达时间2-4-6 BL Bill of Landing 提货单（海运）2-4-7 AWB Air Way Bill 提货单（空运）2-4-8 MAWA Master Air Way Bill主提货单2-4-9 HAWB House Air Way Bill副提货单2-4-10 TEU Twenty foot Equipment Unit(Contain)二十英尺货柜2-4-11 FEU Forty foot Equipment Unit(Contain)四十英尺货柜2-4-12 CY Container Yard货柜场2-4-13 THC Terminal Handing Charge 码头费2-4-14 ORC Original Receiving Charge码头费2-5 PUR Purchasing采购2-5-1 FOB Free on Board货运至甲板2-5-2 CIF Cost Insurance Freight2-5-3 OA Open Account 开户2-5-4 TT Telegram Transfer电汇2-5-5 COD Cash On Delivery 现金支付2-5-6 CRP Cost Reduction Program降低成本方案2-5-7 PR Purchasing Requisition采购申请2-5-8 PO Purchasing Order采购单2-5-9 LT Lead Time 交期2-5-10 LLT Long Lead Time 长时间交期2-5-11 Payment term 付款条件2-5-12 Debit note 扣款2-5-13 CRP Cost Reduction Program 降价计划2-5-14 Quotation 报价3 MFG Manufacturing Production制造控制3-1 DL Director Labor直接人工3-2 IDL Indirect Labor间接人工3-3 DLH Direct Labor Hours直接工时3-4 Productivity=UTS/DLH3-5 PPH Pieces Per Hour每小时件数3-6 Efficiency=Actual/T arget(%)3-7 DT Machine Down Time停机时间3-8 AI Auto Insertion自动插入3-9 MI Manual Insertion人工插入3-10 SMD Surface Mount Device表面粘着零件SMT Surface mount technology 表面粘着技术3-11 B/I Burn In (for how many hours at how many degree)烧机3-12 Equipment Utilization3-13 WI work instruction 工作说明3-14 SOP standard operation procedure作业指导书3-15 R/I run in 运转机器3-16 ESD electrical static discharge 静电释放3-17 MP mass production 量产3-18 EMC Electro Magnetic Compatibility, 电磁兼容性3-19 EMI Electro Magnetic Interference, 电磁干扰3-19 SIR Surface Impedance Resistance 表面阻抗测试4 Engineer工程4-1 PE Products Engineer; 产品工程Process engineer制程工程4-2 TE Test Engineer测试工程4-3 ME Manufacturing Engineer;制造工程Mechanical Engineer机械工程4-4 IE Industrial Engineer工业工程4-5 DCC Document Control Center文管中心4-6 BOM Bill Of Material材料清单4-7 ECN Engineering Change Notice工程变动公告4-8 TECN Temporary Engineering Change Notice工程临时变动公告4-9 ATY Assembly Test Yield Total Yield直通率4-10 TPM Total Productivity Maintenance全面生产维护4-11 PM product manager ;project manager 产品经理;项目经理4-12 ECR engineering change request 工程变更申请4-13 ECO engineering change order 工程变更指令4-14 EN engineering notice 工程通告4-15 WPS work procedure sheet 作业说明书4-16 ICT in circuit test 电路测试4-17 P/R pilot run ;C/R control run; T/R trial run试做4-18 EVT engineer verification test工程验证测试4-19 DVT design verification test 设计验证测试4-20 MVT multi-verification test 多项验证测试4-21 ORT on going reliability test 出货信赖性测试4-22 S/W software 软件4-23 H/W hardware 硬件4-24 EAR Engineering Aanlysis Request 工程分析需求4-25 ECE Engineering Change Estimation 工程变更评估4-26 ECC Engineering Change Cancellation 工程变更取消4-27 IEM Internal Engineering Meno 内部工程备忘录4-28 PAS Part Approval Sheet 零件承认书4-29 DAB Daily Action Boaed 日常工作广告牌4-30 TMR Tooling Modify Report 修模协议书4-31 CRT Control Run Testing 试产测试4-32 DCD Design Change Description 设计变更通知4-33 ESR Engineering Study Report 工程研究报告4-34 EI Engineering Information 工程讯息4-35 PMP Process Management Plan 制程管制计划4-36 MBO Management By Object 目标管理4-37 KPI Key Performance Indicator 重点绩效指标4-38 PIP Part Inspection Plan 零件检验标准4-39 CTF Criticle T o Function 功能重点尺寸4-40 CTA Criticle T o Assembly 组装重点尺寸4-41 R&D Research and Development 研究与开发4-42 GR&R Gauge Repeatability and Reproducibility 治具重复性及重现性验证4-43 Cpk 制程能力指标4-44 FAI First Article Inspection 首件检查表5 QA Quality Assurance质量保证QRA Quality & Reliability Assurance质量与可靠性保证5-1 MQA Manufacturing Quality Assurance制造质量保证5-2 DQA Design Quality Assurance设计质量保证5-3 QC Quality Control质量控制5-4 IQC Incoming Quality Control进货质量控制5-5 VQC Vendor Quality Control售货质量控制5-6 IPQC In Process Quality Control制程质量控制5-7 OQA Out going Quality Control 出货质量控制5-8 QE Quality Engineer质量工程5-9 AQL Acceptable Quality Level可接受的质量水平5-10 DPPM Defective Pieces Per Million units百万件中有损件数5-11 PPM Pieces Per million百万分之一5-12 CS Custom Service顾客服务5-13 MRB Material Review Board 材料审核委员会5-14 DMR Defective Material Report材料缺陷报告5-15 RMA Return Material Administration材料回收处理5-16 Life Test 寿命测试5-17 T/C Temperature Cycle温度循环5-18 H/T High Temperature Test高温测试5-19 L/T Low Temperature Test低温测试5-20 ISO International Standard Organization国际标准化组识5-21 SPC Statistic process control统计过程控制5-22 "5S" 整理.整顿.清理.清扫.素养5-23 VMI visual mechanical inspection 外观机构检验5-24 MIL-STD military standard 美军标准5-25 SPEC specification 规格5-26 AVL approval vendor list 合格厂商名单5-27 QVL qualified vendor list 合格厂商名单5-28 FQC final quality control 最终质量控制5-29 OBA open box audit 成品检验5-30 EAR engineering analysis request 工程分析需求5-31 FAI first aide inspection 首件检验5-32 VQM vendor quality management 厂商质量管理5-33 CAR corrective action request 改进对策要求5-34 4M man; machine; material; method 人、机、材、方法5-35 M man;machine;material;method;measurement 人、机、材、方法测量5-36 MTBF mean time between failure平均寿命5-37 TTL total 总量5-38 MRT Markeing Relability Testing 信赖性测试5-39 8 D 8 Disciplines5-40 Q7 Method (Stratification: Histogram; Pareto; Scatter; (Cause & effect diagram) Fish Bone; (Check sheets); (Graphs & Control Chart)5-41 6 Sigma5-42 3 W What, Who, When5-43 2 Q Quality and Quantity5-44 1 G 1 Goal 一个目标6 FIN Finance &Accounting财务与帐目6-1 P&L Profit &Lose6-2 PV Performance Variance现象差异6-3 3 Element of Cost=M,L,O6-4 M Material材料6-5 L Labor人力6-6 O Overhead管理费用6-7 Fix OH Fixed Overhead固定管理费用6-8 Var OH Variable Overhead不定管理费用6-9 COGS Cost Of Goods Sold工厂制造成本6-10 AR Account Receivable应收6-11 AP Account Payable应支7 MIS Management Information System资讯管理系统7-1 IS Information System资讯系统7-2 IT Information Technology 信息技术、资讯技术7-3 MRP Material Requisition Plan材料需求计划7-4 I2 Information Integration System资讯整合系统7-5 SAP System Application Programming系统申请项目7-6 ERP Enterprise Resource Programming企业资源项目8 HR Human Resource人力资源8-1 PR Public relation公共关系8-2 T/O Turn Over Rate =Monthly T/O Total People*12 8-3 GR General Affair总务。

工厂专业英语术语Assembly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Pneumatic screw driver气动起子worktable 工作桌OO BA开箱检查fit together组装在一起fasten锁紧(螺丝) fixture 夹具(治具) pallet栈板b arcode条码barcode scanner条码扫描器fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cos metic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs. inch 镑、英寸EMI gasket导电条front plate前板rear plate后板chassis 基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试Voltage switch of SPS 电源电压接拉键sheet metal parts 冲件plastic parts塑胶件SOP制造作业程序material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线left fork叉车personnel resource departmen t 人力资源部production department生产部门planning department企划部QC Secti on品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common e quipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床planer |'plein?|刨床miller铣床grinder磨床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager | =vice manager副理section supervisor课长deputy section supervisor =vice section superisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |'skr?pid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |' ksi'dei?n|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓administration/general affairs dept总务部automatic screwdriver电动启子thicknes s gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单location地点present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheet PCE组装厂生产排配表model机锺work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet 库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked 待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet 年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list 备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die butto n圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopp er清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetizat ion去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料deg rease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products 报放心品defective products不良品finished products成品disposed products处理品barcode 条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer 备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting m achine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction =interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕?? shine 亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grai n细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenchi ng淬火tempering回火annealing退火carbonization碳化tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机。

工厂专业英语术语Assembly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet g un拉钉枪Screw driver起子Pneumatic screw driver气动起子worktable 工作桌OOBA 开箱检查fit together组装在一起fasten锁紧(螺丝) fixture 夹具(治具) pallet栈板barcod e条码barcode scanner条码扫描器fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cosm etic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs. inch镑、英寸EMI gasket导电条front plate前板rear plate后板chassis 基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试Voltage switch of SPS 电源电压接拉键sheet metal parts 冲件plastic parts塑胶件SOP制造作业程序material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线left fork叉车personnel resource department 人力资源部production department生产部门planning department企划部QC Section 品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equ ipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床planer |'plein?|刨床miller铣床grinder磨床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager | =vice manager副理section supervisor课长deputy section supervisor =vice section superisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |'skr?pid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |' ksi'dei?n|氧化scratch刮伤d ents压痕defective upsiding down抽芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓administration/general affairs dept总务部automatic screwdriver电动启子thickness g auge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单location地点present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheet PCE组装厂生产排配表model机锺work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet 库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked 待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet 年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam b lock滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button 圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper 清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetizati on去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrea se脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products 报放心品defective products不良品finished products成品disposed products处理品barcode 条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting mac hine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=i nteraction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕?? shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain 细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液cr usher破碎机。

工厂专业英语术语Assembly line组装线 Layout布置图 Conveyer流水线物料板 Rivet table拉钉机 Rivet gun拉钉枪 Screw driver起子Pneumatic screw driver气动起子 worktable 工作桌 OOBA开箱检查 fit together组装在一起 fasten锁紧(螺丝) fixture 夹具(治具) pallet栈板 barcode条码 barcode scanner条码扫描器 fuse together熔合 fuse machine热熔机repair修理 operator操作人员 QC品管 supervisor 科长 ME制造工程师 MT制造生技 cosmetic inspect外观检查 inner parts inspect内部检查 thumb screw大头螺丝 lbs. inch镑、英寸 EMI gasket导电条front plate前板 rear plate后板 chassis 基座 bezel panel面板power button电源按键 reset button重置键Hi-pot test of SPS高源高压测试Voltage switch of SPS 电源电压接拉键sheet metal parts 冲件plastic parts塑料件 SOP制造作业程序 material check list物料检查表 work cell工作间 trolley台车 carton纸箱 sub-line支线 left fork叉车personnel resource department 人力资源部 production department生产部门 planning department企划部 QC Section品管科stamping factory冲压厂 painting factory烤漆厂 molding factory成型厂 common equipment常用设备uncoiler and straightener整平机punching machine 冲床 robot机械手 hydraulic machine油压机lathe车床 planer |'plein?|刨床 miller铣床 grinder磨床linear cutting线切割 electrical sparkle电火花 welder电焊机staker=reviting machine铆合机 position职务 president董事长general manager总经理special assistant manager特助factory director厂长 department director部长deputy manager | =vice manager副经理 section supervisor科长deputy section supervisor =vice section superisor副科长group leader/supervisor组长 line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库 pack packing包装to apply oil擦油to file burr 锉毛刺 final inspection终检to connect material接料to reverse material 翻料 wet station沾湿台 Tiana天那水cleaning cloth抹布 to load material上料to unload material卸料to return material/stock to退料 scraped |'skr?pid|报废scrape ..v.刮;削 deficient purchase来料不良 manufacture procedure制程deficient manufacturing procedure制程不良oxidation |' ksi'dei?n|氧化 scratch刮伤 dents压痕defective upsiding down抽芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲 production capacity生产力education and training教育与训练 proposal improvement提案改善spare parts=buffer备件 forklift叉车 trailer=long vehicle拖板车compound die合模 die locker锁模器pressure plate=plate pinch压板 bolt螺栓administration/general affairs dept总务部automatic screwdriver电动启子 thickness gauge厚薄规gauge(or jig)治具 power wire电源线 buzzle蜂鸣器 defective product label不良标签identifying sheet list标示单 location地点 present members出席人员 subject主题conclusion结论 decision items决议事项 responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheet PCE组装厂生产排配表 model机锺work order工令 revision版次 remark备注 production control confirmation生产确认checked by初审 approved by核准 department部门stock age analysis sheet 库存货龄分析表on-hand inventory现有库存 available material良品可使用obsolete material良品已呆滞to be inspected or reworked 待验或重工total合计 cause description原因说明part number/ P/N 料号type形态 item/group/class类别 quality品质 prepared by制表 notes说明year-end physical inventory difference analysis sheet 年终盘点差异分析表physical inventory盘点数量 physical count quantity帐面数量 difference quantity差异量cause analysis原因分析 raw materials原料 materials物料 finished product成品semi-finished product半成品 packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品 disposed goods处理品 warehouse/hub仓库on way location在途仓 oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓 skid/pallet栈板 tox machine自铆机 wire EDM线割EDM放电机 coil stock卷料 sheet stock片料 tolerance工差 score=groove压线 cam block滑块pilot导正筒 trim剪外边 pierce剪内边 drag form压锻差pocket for the punch head挂鈎槽 slug hole废料孔 feature die公母模expansion dwg展开图 radius半径 shim(wedge)楔子 torch-flame cut火焰切割set screw止付螺丝 form block折刀 stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子 stock locater block定位块under cut=scrap chopper清角active plate活动板 baffle plate挡块 cover plate盖板 male die公模 female die母模groove punch压线冲子 air-cushion eject-rod气垫顶杆 spring-box eject-plate弹簧箱顶板bushing block衬套 insert 入块 club car高尔夫球车 capability能力parameter参数 factor系数 phosphate皮膜化成 viscosity涂料粘度 alkalidipping脱脂main manifold主集流脉 bezel斜视规 blanking穿落模 dejecting顶固模 demagnetization去磁;消磁high-speed transmission高速传递 heat dissipation热传 rack上料 degrease脱脂 rinse水洗alkaline etch龄咬 desmut剥黑膜 D.I. rinse纯水次 Chromate铬酸处理 Anodize阳性处理seal封孔 revision版次 part number/P/N料号 good products良品 scraped products报放心品defective products不良品 finished products成品 disposed products处理品 barcode条码flow chart流程表单 assembly组装 stamping冲压 molding成型 spare parts=buffer备品coordinate座标 dismantle the die折模 auxiliary fuction辅助功能 poly-line多义线heater band 加热片 thermocouple热电偶 sand blasting喷沙 grit 砂砾 derusting machine除锈机degate打浇口 dryer烘乾机 induction感应 induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器 concave凸 convex凹 short射料不足 nick缺口 speck瑕?? shine亮班splay 银纹 gas mark焦痕 delamination起鳞 cold slug冷块 blush 导色 gouge沟槽;凿槽satin texture段面咬花 witness line证示线 patent专利 grit沙砾 granule=peuet=grain细粒grit maker抽粒机 cushion缓冲 magnalium镁铝合金 magnesium镁金 metal plate钣金lathe车 mill锉 plane刨 grind磨 drill铝 boring镗 blinster气泡 fillet镶;嵌边through-hole form通孔形式 voller pin formality滚针形式 cam driver铡楔 shank摸柄crank shaft曲柄轴 augular offset角度偏差 velocity速度production tempo生产进度现状 torque扭矩spline=the multiple keys花键 quenching淬火tempering回火 annealing退火 carbonization碳化tungsten high speed steel钨高速的moly high speed steel钼高速的 organic solvent有机溶剂 bracket小磁导 liaison联络单volatile挥发性 resistance电阻 ion离子 titrator滴定仪 beacon警示灯 coolant冷却液 crusher破碎机。